🧑💻 Dump BOTH and EITHER macros (#25908)
This commit is contained in:
Scott Lahteine
GitHub
@@ -46,8 +46,8 @@
|
||||
#if ENABLED(TEST0) || !ENABLED(TEST2) || ENABLED(TEST3) || !ENABLED(TEST1, TEST2, TEST4)
|
||||
#error "ENABLED is borked!"
|
||||
#endif
|
||||
#if BOTH(TEST0, TEST1)
|
||||
#error "BOTH is borked!"
|
||||
#if ALL(TEST0, TEST1)
|
||||
#error "ALL is borked!"
|
||||
#endif
|
||||
#if DISABLED(TEST1) || !DISABLED(TEST3) || DISABLED(TEST4) || DISABLED(TEST0, TEST1, TEST2, TEST4) || !DISABLED(TEST0, TEST3)
|
||||
#error "DISABLED is borked!"
|
||||
@@ -300,45 +300,45 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if BOTH(ENDSTOPPULLUPS, ENDSTOPPULLDOWNS)
|
||||
#if ALL(ENDSTOPPULLUPS, ENDSTOPPULLDOWNS)
|
||||
#error "Enable only one of ENDSTOPPULLUPS or ENDSTOPPULLDOWNS."
|
||||
#elif BOTH(FIL_RUNOUT_PULLUP, FIL_RUNOUT_PULLDOWN)
|
||||
#elif ALL(FIL_RUNOUT_PULLUP, FIL_RUNOUT_PULLDOWN)
|
||||
#error "Enable only one of FIL_RUNOUT_PULLUP or FIL_RUNOUT_PULLDOWN."
|
||||
#elif BOTH(ENDSTOPPULLUP_XMAX, ENDSTOPPULLDOWN_XMAX)
|
||||
#elif ALL(ENDSTOPPULLUP_XMAX, ENDSTOPPULLDOWN_XMAX)
|
||||
#error "Enable only one of ENDSTOPPULLUP_X_MAX or ENDSTOPPULLDOWN_X_MAX."
|
||||
#elif BOTH(ENDSTOPPULLUP_YMAX, ENDSTOPPULLDOWN_YMAX)
|
||||
#elif ALL(ENDSTOPPULLUP_YMAX, ENDSTOPPULLDOWN_YMAX)
|
||||
#error "Enable only one of ENDSTOPPULLUP_Y_MAX or ENDSTOPPULLDOWN_Y_MAX."
|
||||
#elif BOTH(ENDSTOPPULLUP_ZMAX, ENDSTOPPULLDOWN_ZMAX)
|
||||
#elif ALL(ENDSTOPPULLUP_ZMAX, ENDSTOPPULLDOWN_ZMAX)
|
||||
#error "Enable only one of ENDSTOPPULLUP_Z_MAX or ENDSTOPPULLDOWN_Z_MAX."
|
||||
#elif BOTH(ENDSTOPPULLUP_IMAX, ENDSTOPPULLDOWN_IMAX)
|
||||
#elif ALL(ENDSTOPPULLUP_IMAX, ENDSTOPPULLDOWN_IMAX)
|
||||
#error "Enable only one of ENDSTOPPULLUP_I_MAX or ENDSTOPPULLDOWN_I_MAX."
|
||||
#elif BOTH(ENDSTOPPULLUP_JMAX, ENDSTOPPULLDOWN_JMAX)
|
||||
#elif ALL(ENDSTOPPULLUP_JMAX, ENDSTOPPULLDOWN_JMAX)
|
||||
#error "Enable only one of ENDSTOPPULLUP_J_MAX or ENDSTOPPULLDOWN_J_MAX."
|
||||
#elif BOTH(ENDSTOPPULLUP_KMAX, ENDSTOPPULLDOWN_KMAX)
|
||||
#elif ALL(ENDSTOPPULLUP_KMAX, ENDSTOPPULLDOWN_KMAX)
|
||||
#error "Enable only one of ENDSTOPPULLUP_K_MAX or ENDSTOPPULLDOWN_K_MAX."
|
||||
#elif BOTH(ENDSTOPPULLUP_UMAX, ENDSTOPPULLDOWN_UMAX)
|
||||
#elif ALL(ENDSTOPPULLUP_UMAX, ENDSTOPPULLDOWN_UMAX)
|
||||
#error "Enable only one of ENDSTOPPULLUP_U_MAX or ENDSTOPPULLDOWN_U_MAX."
|
||||
#elif BOTH(ENDSTOPPULLUP_VMAX, ENDSTOPPULLDOWN_VMAX)
|
||||
#elif ALL(ENDSTOPPULLUP_VMAX, ENDSTOPPULLDOWN_VMAX)
|
||||
#error "Enable only one of ENDSTOPPULLUP_V_MAX or ENDSTOPPULLDOWN_V_MAX."
|
||||
#elif BOTH(ENDSTOPPULLUP_WMAX, ENDSTOPPULLDOWN_WMAX)
|
||||
#elif ALL(ENDSTOPPULLUP_WMAX, ENDSTOPPULLDOWN_WMAX)
|
||||
#error "Enable only one of ENDSTOPPULLUP_W_MAX or ENDSTOPPULLDOWN_W_MAX."
|
||||
#elif BOTH(ENDSTOPPULLUP_XMIN, ENDSTOPPULLDOWN_XMIN)
|
||||
#elif ALL(ENDSTOPPULLUP_XMIN, ENDSTOPPULLDOWN_XMIN)
|
||||
#error "Enable only one of ENDSTOPPULLUP_X_MIN or ENDSTOPPULLDOWN_X_MIN."
|
||||
#elif BOTH(ENDSTOPPULLUP_YMIN, ENDSTOPPULLDOWN_YMIN)
|
||||
#elif ALL(ENDSTOPPULLUP_YMIN, ENDSTOPPULLDOWN_YMIN)
|
||||
#error "Enable only one of ENDSTOPPULLUP_Y_MIN or ENDSTOPPULLDOWN_Y_MIN."
|
||||
#elif BOTH(ENDSTOPPULLUP_ZMIN, ENDSTOPPULLDOWN_ZMIN)
|
||||
#elif ALL(ENDSTOPPULLUP_ZMIN, ENDSTOPPULLDOWN_ZMIN)
|
||||
#error "Enable only one of ENDSTOPPULLUP_Z_MIN or ENDSTOPPULLDOWN_Z_MIN."
|
||||
#elif BOTH(ENDSTOPPULLUP_IMIN, ENDSTOPPULLDOWN_IMIN)
|
||||
#elif ALL(ENDSTOPPULLUP_IMIN, ENDSTOPPULLDOWN_IMIN)
|
||||
#error "Enable only one of ENDSTOPPULLUP_I_MIN or ENDSTOPPULLDOWN_I_MIN."
|
||||
#elif BOTH(ENDSTOPPULLUP_JMIN, ENDSTOPPULLDOWN_JMIN)
|
||||
#elif ALL(ENDSTOPPULLUP_JMIN, ENDSTOPPULLDOWN_JMIN)
|
||||
#error "Enable only one of ENDSTOPPULLUP_J_MIN or ENDSTOPPULLDOWN_J_MIN."
|
||||
#elif BOTH(ENDSTOPPULLUP_KMIN, ENDSTOPPULLDOWN_KMIN)
|
||||
#elif ALL(ENDSTOPPULLUP_KMIN, ENDSTOPPULLDOWN_KMIN)
|
||||
#error "Enable only one of ENDSTOPPULLUP_K_MIN or ENDSTOPPULLDOWN_K_MIN."
|
||||
#elif BOTH(ENDSTOPPULLUP_UMIN, ENDSTOPPULLDOWN_UMIN)
|
||||
#elif ALL(ENDSTOPPULLUP_UMIN, ENDSTOPPULLDOWN_UMIN)
|
||||
#error "Enable only one of ENDSTOPPULLUP_U_MIN or ENDSTOPPULLDOWN_U_MIN."
|
||||
#elif BOTH(ENDSTOPPULLUP_VMIN, ENDSTOPPULLDOWN_VMIN)
|
||||
#elif ALL(ENDSTOPPULLUP_VMIN, ENDSTOPPULLDOWN_VMIN)
|
||||
#error "Enable only one of ENDSTOPPULLUP_V_MIN or ENDSTOPPULLDOWN_V_MIN."
|
||||
#elif BOTH(ENDSTOPPULLUP_WMIN, ENDSTOPPULLDOWN_WMIN)
|
||||
#elif ALL(ENDSTOPPULLUP_WMIN, ENDSTOPPULLDOWN_WMIN)
|
||||
#error "Enable only one of ENDSTOPPULLUP_W_MIN or ENDSTOPPULLDOWN_W_MIN."
|
||||
#endif
|
||||
|
||||
@@ -455,7 +455,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
* I2C Position Encoders
|
||||
*/
|
||||
#if ENABLED(I2C_POSITION_ENCODERS)
|
||||
#if !BOTH(BABYSTEPPING, BABYSTEP_XY)
|
||||
#if !ALL(BABYSTEPPING, BABYSTEP_XY)
|
||||
#error "I2C_POSITION_ENCODERS requires BABYSTEPPING and BABYSTEP_XY."
|
||||
#elif !WITHIN(I2CPE_ENCODER_CNT, 1, 5)
|
||||
#error "I2CPE_ENCODER_CNT must be between 1 and 5."
|
||||
@@ -468,11 +468,11 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
#if ENABLED(SCARA)
|
||||
#error "BABYSTEPPING is not implemented for SCARA yet."
|
||||
#elif ENABLED(BABYSTEP_XY) && EITHER(MARKFORGED_XY, MARKFORGED_YX)
|
||||
#elif ENABLED(BABYSTEP_XY) && ANY(MARKFORGED_XY, MARKFORGED_YX)
|
||||
#error "BABYSTEPPING only implemented for Z axis on MarkForged."
|
||||
#elif BOTH(DELTA, BABYSTEP_XY)
|
||||
#elif ALL(DELTA, BABYSTEP_XY)
|
||||
#error "BABYSTEPPING only implemented for Z axis on deltabots."
|
||||
#elif BOTH(BABYSTEP_ZPROBE_OFFSET, MESH_BED_LEVELING)
|
||||
#elif ALL(BABYSTEP_ZPROBE_OFFSET, MESH_BED_LEVELING)
|
||||
#error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
|
||||
#elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && !HAS_BED_PROBE
|
||||
#error "BABYSTEP_ZPROBE_OFFSET requires a probe."
|
||||
@@ -482,7 +482,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#error "BABYSTEP_GFX_OVERLAY requires a BABYSTEP_ZPROBE_OFFSET."
|
||||
#elif ENABLED(BABYSTEP_HOTEND_Z_OFFSET) && !HAS_HOTEND_OFFSET
|
||||
#error "BABYSTEP_HOTEND_Z_OFFSET requires 2 or more HOTENDS."
|
||||
#elif BOTH(BABYSTEP_ALWAYS_AVAILABLE, MOVE_Z_WHEN_IDLE)
|
||||
#elif ALL(BABYSTEP_ALWAYS_AVAILABLE, MOVE_Z_WHEN_IDLE)
|
||||
#error "BABYSTEP_ALWAYS_AVAILABLE and MOVE_Z_WHEN_IDLE are incompatible."
|
||||
#elif !defined(BABYSTEP_MULTIPLICATOR_Z)
|
||||
#error "BABYSTEPPING requires BABYSTEP_MULTIPLICATOR_Z."
|
||||
@@ -520,21 +520,21 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#error "FIL_RUNOUT3_PIN is required with NUM_RUNOUT_SENSORS >= 3."
|
||||
#elif NUM_RUNOUT_SENSORS >= 2 && !PIN_EXISTS(FIL_RUNOUT2)
|
||||
#error "FIL_RUNOUT2_PIN is required with NUM_RUNOUT_SENSORS >= 2."
|
||||
#elif BOTH(FIL_RUNOUT1_PULLUP, FIL_RUNOUT1_PULLDOWN)
|
||||
#elif ALL(FIL_RUNOUT1_PULLUP, FIL_RUNOUT1_PULLDOWN)
|
||||
#error "You can't enable FIL_RUNOUT1_PULLUP and FIL_RUNOUT1_PULLDOWN at the same time."
|
||||
#elif BOTH(FIL_RUNOUT2_PULLUP, FIL_RUNOUT2_PULLDOWN)
|
||||
#elif ALL(FIL_RUNOUT2_PULLUP, FIL_RUNOUT2_PULLDOWN)
|
||||
#error "You can't enable FIL_RUNOUT2_PULLUP and FIL_RUNOUT2_PULLDOWN at the same time."
|
||||
#elif BOTH(FIL_RUNOUT3_PULLUP, FIL_RUNOUT3_PULLDOWN)
|
||||
#elif ALL(FIL_RUNOUT3_PULLUP, FIL_RUNOUT3_PULLDOWN)
|
||||
#error "You can't enable FIL_RUNOUT3_PULLUP and FIL_RUNOUT3_PULLDOWN at the same time."
|
||||
#elif BOTH(FIL_RUNOUT4_PULLUP, FIL_RUNOUT4_PULLDOWN)
|
||||
#elif ALL(FIL_RUNOUT4_PULLUP, FIL_RUNOUT4_PULLDOWN)
|
||||
#error "You can't enable FIL_RUNOUT4_PULLUP and FIL_RUNOUT4_PULLDOWN at the same time."
|
||||
#elif BOTH(FIL_RUNOUT5_PULLUP, FIL_RUNOUT5_PULLDOWN)
|
||||
#elif ALL(FIL_RUNOUT5_PULLUP, FIL_RUNOUT5_PULLDOWN)
|
||||
#error "You can't enable FIL_RUNOUT5_PULLUP and FIL_RUNOUT5_PULLDOWN at the same time."
|
||||
#elif BOTH(FIL_RUNOUT6_PULLUP, FIL_RUNOUT6_PULLDOWN)
|
||||
#elif ALL(FIL_RUNOUT6_PULLUP, FIL_RUNOUT6_PULLDOWN)
|
||||
#error "You can't enable FIL_RUNOUT6_PULLUP and FIL_RUNOUT6_PULLDOWN at the same time."
|
||||
#elif BOTH(FIL_RUNOUT7_PULLUP, FIL_RUNOUT7_PULLDOWN)
|
||||
#elif ALL(FIL_RUNOUT7_PULLUP, FIL_RUNOUT7_PULLDOWN)
|
||||
#error "You can't enable FIL_RUNOUT7_PULLUP and FIL_RUNOUT7_PULLDOWN at the same time."
|
||||
#elif BOTH(FIL_RUNOUT8_PULLUP, FIL_RUNOUT8_PULLDOWN)
|
||||
#elif ALL(FIL_RUNOUT8_PULLUP, FIL_RUNOUT8_PULLDOWN)
|
||||
#error "You can't enable FIL_RUNOUT8_PULLUP and FIL_RUNOUT8_PULLDOWN at the same time."
|
||||
#elif FILAMENT_RUNOUT_DISTANCE_MM < 0
|
||||
#error "FILAMENT_RUNOUT_DISTANCE_MM must be greater than or equal to zero."
|
||||
@@ -587,7 +587,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Individual axis homing is useless for DELTAS
|
||||
*/
|
||||
#if BOTH(INDIVIDUAL_AXIS_HOMING_MENU, DELTA)
|
||||
#if ALL(INDIVIDUAL_AXIS_HOMING_MENU, DELTA)
|
||||
#error "INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics."
|
||||
#endif
|
||||
|
||||
@@ -691,7 +691,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* A Dual Nozzle carriage with switching servo
|
||||
*/
|
||||
#if BOTH(SWITCHING_NOZZLE, MECHANICAL_SWITCHING_NOZZLE)
|
||||
#if ALL(SWITCHING_NOZZLE, MECHANICAL_SWITCHING_NOZZLE)
|
||||
#error "Enable only one of SWITCHING_NOZZLE or MECHANICAL_SWITCHING_NOZZLE."
|
||||
#elif ENABLED(MECHANICAL_SWITCHING_NOZZLE)
|
||||
#if EXTRUDERS != 2
|
||||
@@ -747,7 +747,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Single Stepper Dual Extruder with switching servo
|
||||
*/
|
||||
#if BOTH(SWITCHING_EXTRUDER, MECHANICAL_SWITCHING_EXTRUDER)
|
||||
#if ALL(SWITCHING_EXTRUDER, MECHANICAL_SWITCHING_EXTRUDER)
|
||||
#error "Enable only one of SWITCHING_EXTRUDER or MECHANICAL_SWITCHING_EXTRUDER."
|
||||
#elif ENABLED(MECHANICAL_SWITCHING_EXTRUDER)
|
||||
#if EXTRUDERS < 2
|
||||
@@ -855,7 +855,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* (Magnetic) Parking Extruder requirements
|
||||
*/
|
||||
#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
|
||||
#if ANY(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
|
||||
#if ENABLED(EXT_SOLENOID)
|
||||
#error "(MAGNETIC_)PARKING_EXTRUDER and EXT_SOLENOID are incompatible. (Pins are used twice.)"
|
||||
#elif EXTRUDERS != 2
|
||||
@@ -913,7 +913,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Magnetic / Electromagnetic Switching Toolhead requirements
|
||||
*/
|
||||
#if EITHER(MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
|
||||
#if ANY(MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
|
||||
#ifndef SWITCHING_TOOLHEAD_Y_POS
|
||||
#error "(ELECTRO)?MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Y_POS"
|
||||
#elif !defined(SWITCHING_TOOLHEAD_X_POS)
|
||||
@@ -983,7 +983,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Extruder temperature control algorithm - There can be only one!
|
||||
*/
|
||||
#if BOTH(PIDTEMP, MPCTEMP)
|
||||
#if ALL(PIDTEMP, MPCTEMP)
|
||||
#error "Only enable PIDTEMP or MPCTEMP, but not both."
|
||||
#undef MPCTEMP
|
||||
#undef MPC_AUTOTUNE
|
||||
@@ -1007,7 +1007,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Bed Heating Options - PID vs Limit Switching
|
||||
*/
|
||||
#if BOTH(PIDTEMPBED, BED_LIMIT_SWITCHING)
|
||||
#if ALL(PIDTEMPBED, BED_LIMIT_SWITCHING)
|
||||
#error "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED."
|
||||
#endif
|
||||
|
||||
@@ -1030,7 +1030,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Chamber Heating Options - PID vs Limit Switching
|
||||
*/
|
||||
#if BOTH(PIDTEMPCHAMBER, CHAMBER_LIMIT_SWITCHING)
|
||||
#if ALL(PIDTEMPCHAMBER, CHAMBER_LIMIT_SWITCHING)
|
||||
#error "To use CHAMBER_LIMIT_SWITCHING you must disable PIDTEMPCHAMBER."
|
||||
#endif
|
||||
|
||||
@@ -1196,7 +1196,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Some things should not be used on Belt Printers
|
||||
*/
|
||||
#if BOTH(BELTPRINTER, HAS_LEVELING)
|
||||
#if ALL(BELTPRINTER, HAS_LEVELING)
|
||||
#error "Bed Leveling is not compatible with BELTPRINTER."
|
||||
#endif
|
||||
|
||||
@@ -1218,7 +1218,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Z_PROBE_SLED is incompatible with DELTA
|
||||
*/
|
||||
#if BOTH(Z_PROBE_SLED, DELTA)
|
||||
#if ALL(Z_PROBE_SLED, DELTA)
|
||||
#error "You cannot use Z_PROBE_SLED with DELTA."
|
||||
#endif
|
||||
|
||||
@@ -1361,7 +1361,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Mag mounted probe requirements
|
||||
*/
|
||||
#if BOTH(MAG_MOUNTED_PROBE, USE_PROBE_FOR_Z_HOMING) && DISABLED(Z_SAFE_HOMING)
|
||||
#if ALL(MAG_MOUNTED_PROBE, USE_PROBE_FOR_Z_HOMING) && DISABLED(Z_SAFE_HOMING)
|
||||
#error "MAG_MOUNTED_PROBE requires Z_SAFE_HOMING if it's being used to home Z."
|
||||
#endif
|
||||
|
||||
@@ -1586,7 +1586,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if BOTH(PREHEAT_BEFORE_PROBING, PREHEAT_BEFORE_LEVELING)
|
||||
#if ALL(PREHEAT_BEFORE_PROBING, PREHEAT_BEFORE_LEVELING)
|
||||
#error "Disable PREHEAT_BEFORE_LEVELING when using PREHEAT_BEFORE_PROBING."
|
||||
#endif
|
||||
|
||||
@@ -1703,7 +1703,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Make sure DISABLE_[XYZ] compatible with selected homing options
|
||||
*/
|
||||
#if HAS_DISABLE_MAIN_AXES && EITHER(HOME_AFTER_DEACTIVATE, Z_SAFE_HOMING)
|
||||
#if HAS_DISABLE_MAIN_AXES && ANY(HOME_AFTER_DEACTIVATE, Z_SAFE_HOMING)
|
||||
#error "DISABLE_[XYZIJKUVW] is not compatible with HOME_AFTER_DEACTIVATE or Z_SAFE_HOMING."
|
||||
#endif
|
||||
|
||||
@@ -1725,7 +1725,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#error "POWER_MONITOR_CURRENT requires a valid POWER_MONITOR_CURRENT_PIN."
|
||||
#elif ENABLED(POWER_MONITOR_VOLTAGE) && !PIN_EXISTS(POWER_MONITOR_VOLTAGE)
|
||||
#error "POWER_MONITOR_VOLTAGE requires POWER_MONITOR_VOLTAGE_PIN to be defined."
|
||||
#elif BOTH(POWER_MONITOR_CURRENT, POWER_MONITOR_VOLTAGE) && POWER_MONITOR_CURRENT_PIN == POWER_MONITOR_VOLTAGE_PIN
|
||||
#elif ALL(POWER_MONITOR_CURRENT, POWER_MONITOR_VOLTAGE) && POWER_MONITOR_CURRENT_PIN == POWER_MONITOR_VOLTAGE_PIN
|
||||
#error "POWER_MONITOR_CURRENT_PIN and POWER_MONITOR_VOLTAGE_PIN must be different."
|
||||
#endif
|
||||
|
||||
@@ -1757,7 +1757,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#if ENABLED(SAV_3DGLCD)
|
||||
#if NONE(U8GLIB_SSD1306, U8GLIB_SH1106)
|
||||
#error "Enable a SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106."
|
||||
#elif BOTH(U8GLIB_SSD1306, U8GLIB_SH1106)
|
||||
#elif ALL(U8GLIB_SSD1306, U8GLIB_SH1106)
|
||||
#error "Only enable one SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106."
|
||||
#endif
|
||||
#endif
|
||||
@@ -1841,7 +1841,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* Make sure FAN_*_PWM values are sensible
|
||||
*/
|
||||
#if EITHER(HAS_FAN, USE_CONTROLLER_FAN)
|
||||
#if ANY(HAS_FAN, USE_CONTROLLER_FAN)
|
||||
#if !WITHIN(FAN_MIN_PWM, 0, 255)
|
||||
#error "FAN_MIN_PWM must be a value from 0 to 255."
|
||||
#elif !WITHIN(FAN_MAX_PWM, 0, 255)
|
||||
@@ -2047,7 +2047,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#elif !ANY_PIN(TEMP_0, TEMP_0_CS) && !TEMP_SENSOR_0_IS_DUMMY
|
||||
#error "TEMP_0_PIN or TEMP_0_CS_PIN not defined for this board."
|
||||
#endif
|
||||
#if EITHER(HAS_MULTI_HOTEND, HEATERS_PARALLEL) && !HAS_HEATER_1
|
||||
#if ANY(HAS_MULTI_HOTEND, HEATERS_PARALLEL) && !HAS_HEATER_1
|
||||
#error "HEATER_1_PIN is not defined. TEMP_SENSOR_1 might not be set, or the board (not EEB / EEF?) doesn't define a pin."
|
||||
#endif
|
||||
#if HAS_MULTI_HOTEND
|
||||
@@ -2230,7 +2230,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
/**
|
||||
* FYSETC/MKS/BTT Mini Panel Requirements
|
||||
*/
|
||||
#if EITHER(FYSETC_242_OLED_12864, FYSETC_MINI_12864_2_1)
|
||||
#if ANY(FYSETC_242_OLED_12864, FYSETC_MINI_12864_2_1)
|
||||
#ifndef NEO_RGB
|
||||
#define NEO_RGB 123
|
||||
#define FAUX_RGB 1
|
||||
@@ -2244,7 +2244,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#undef NEO_RGB
|
||||
#undef FAUX_RGB
|
||||
#endif
|
||||
#elif EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) && DISABLED(RGB_LED)
|
||||
#elif ANY(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) && DISABLED(RGB_LED)
|
||||
#error "Your FYSETC Mini Panel requires RGB_LED."
|
||||
#endif
|
||||
|
||||
@@ -2354,12 +2354,12 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
// Z homing requirements
|
||||
#if Z_HOME_TO_MAX && ENABLED(USE_PROBE_FOR_Z_HOMING)
|
||||
#error "Z_HOME_DIR must be -1 when homing Z with the probe."
|
||||
#elif BOTH(HOMING_Z_WITH_PROBE, Z_MULTI_ENDSTOPS)
|
||||
#elif ALL(HOMING_Z_WITH_PROBE, Z_MULTI_ENDSTOPS)
|
||||
#error "Z_MULTI_ENDSTOPS is incompatible with USE_PROBE_FOR_Z_HOMING."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if BOTH(HOME_Z_FIRST, USE_PROBE_FOR_Z_HOMING)
|
||||
#if ALL(HOME_Z_FIRST, USE_PROBE_FOR_Z_HOMING)
|
||||
#error "HOME_Z_FIRST can't be used when homing Z with a probe."
|
||||
#endif
|
||||
|
||||
@@ -2498,21 +2498,21 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
* Fan check
|
||||
*/
|
||||
#if HAS_FANCHECK
|
||||
#if BOTH(E0_FAN_TACHO_PULLUP, E0_FAN_TACHO_PULLDOWN)
|
||||
#if ALL(E0_FAN_TACHO_PULLUP, E0_FAN_TACHO_PULLDOWN)
|
||||
#error "Enable only one of E0_FAN_TACHO_PULLUP or E0_FAN_TACHO_PULLDOWN."
|
||||
#elif BOTH(E1_FAN_TACHO_PULLUP, E1_FAN_TACHO_PULLDOWN)
|
||||
#elif ALL(E1_FAN_TACHO_PULLUP, E1_FAN_TACHO_PULLDOWN)
|
||||
#error "Enable only one of E1_FAN_TACHO_PULLUP or E1_FAN_TACHO_PULLDOWN."
|
||||
#elif BOTH(E2_FAN_TACHO_PULLUP, E2_FAN_TACHO_PULLDOWN)
|
||||
#elif ALL(E2_FAN_TACHO_PULLUP, E2_FAN_TACHO_PULLDOWN)
|
||||
#error "Enable only one of E2_FAN_TACHO_PULLUP or E2_FAN_TACHO_PULLDOWN."
|
||||
#elif BOTH(E3_FAN_TACHO_PULLUP, E3_FAN_TACHO_PULLDOWN)
|
||||
#elif ALL(E3_FAN_TACHO_PULLUP, E3_FAN_TACHO_PULLDOWN)
|
||||
#error "Enable only one of E3_FAN_TACHO_PULLUP or E3_FAN_TACHO_PULLDOWN."
|
||||
#elif BOTH(E4_FAN_TACHO_PULLUP, E4_FAN_TACHO_PULLDOWN)
|
||||
#elif ALL(E4_FAN_TACHO_PULLUP, E4_FAN_TACHO_PULLDOWN)
|
||||
#error "Enable only one of E4_FAN_TACHO_PULLUP or E4_FAN_TACHO_PULLDOWN."
|
||||
#elif BOTH(E5_FAN_TACHO_PULLUP, E5_FAN_TACHO_PULLDOWN)
|
||||
#elif ALL(E5_FAN_TACHO_PULLUP, E5_FAN_TACHO_PULLDOWN)
|
||||
#error "Enable only one of E5_FAN_TACHO_PULLUP or E5_FAN_TACHO_PULLDOWN."
|
||||
#elif BOTH(E6_FAN_TACHO_PULLUP, E6_FAN_TACHO_PULLDOWN)
|
||||
#elif ALL(E6_FAN_TACHO_PULLUP, E6_FAN_TACHO_PULLDOWN)
|
||||
#error "Enable only one of E6_FAN_TACHO_PULLUP or E6_FAN_TACHO_PULLDOWN."
|
||||
#elif BOTH(E7_FAN_TACHO_PULLUP, E7_FAN_TACHO_PULLDOWN)
|
||||
#elif ALL(E7_FAN_TACHO_PULLUP, E7_FAN_TACHO_PULLDOWN)
|
||||
#error "Enable only one of E7_FAN_TACHO_PULLUP or E7_FAN_TACHO_PULLDOWN."
|
||||
#endif
|
||||
#elif ENABLED(AUTO_REPORT_FANS)
|
||||
@@ -2640,7 +2640,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
|
||||
#if ENABLED(TFT_GENERIC) && NONE(TFT_INTERFACE_FSMC, TFT_INTERFACE_SPI)
|
||||
#error "TFT_GENERIC requires either TFT_INTERFACE_FSMC or TFT_INTERFACE_SPI interface."
|
||||
#elif BOTH(TFT_INTERFACE_FSMC, TFT_INTERFACE_SPI)
|
||||
#elif ALL(TFT_INTERFACE_FSMC, TFT_INTERFACE_SPI)
|
||||
#error "Please enable only one of TFT_INTERFACE_FSMC or TFT_INTERFACE_SPI."
|
||||
#endif
|
||||
|
||||
@@ -2664,7 +2664,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#error "GRAPHICAL_TFT_UPSCALE must be between 2 and 8."
|
||||
#endif
|
||||
|
||||
#if BOTH(CHIRON_TFT_STANDARD, CHIRON_TFT_NEW)
|
||||
#if ALL(CHIRON_TFT_STANDARD, CHIRON_TFT_NEW)
|
||||
#error "Please select only one of CHIRON_TFT_STANDARD or CHIRON_TFT_NEW."
|
||||
#endif
|
||||
|
||||
@@ -2686,7 +2686,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
static_assert(strcmp(STRINGIFY(LCD_LANGUAGE_2), "zh_CN") == 0, "LCD_LANGUAGE_2 must be set to zh_CN for ANYCUBIC_LCD_VYPER.");
|
||||
#endif
|
||||
|
||||
#if EITHER(MKS_TS35_V2_0, BTT_TFT35_SPI_V1_0) && SD_CONNECTION_IS(LCD)
|
||||
#if ANY(MKS_TS35_V2_0, BTT_TFT35_SPI_V1_0) && SD_CONNECTION_IS(LCD)
|
||||
#error "SDCARD_CONNECTION cannot be set to LCD for the enabled TFT. No available SD card reader."
|
||||
#endif
|
||||
|
||||
@@ -2696,25 +2696,25 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#if ENABLED(DWIN_CREALITY_LCD)
|
||||
#if !HAS_MEDIA
|
||||
#error "DWIN_CREALITY_LCD requires SDSUPPORT to be enabled."
|
||||
#elif EITHER(PID_EDIT_MENU, PID_AUTOTUNE_MENU)
|
||||
#elif ANY(PID_EDIT_MENU, PID_AUTOTUNE_MENU)
|
||||
#error "DWIN_CREALITY_LCD does not support PID_EDIT_MENU or PID_AUTOTUNE_MENU."
|
||||
#elif EITHER(MPC_EDIT_MENU, MPC_AUTOTUNE_MENU)
|
||||
#elif ANY(MPC_EDIT_MENU, MPC_AUTOTUNE_MENU)
|
||||
#error "DWIN_CREALITY_LCD does not support MPC_EDIT_MENU or MPC_AUTOTUNE_MENU."
|
||||
#elif ENABLED(LCD_BED_TRAMMING)
|
||||
#error "DWIN_CREALITY_LCD does not support LCD_BED_TRAMMING."
|
||||
#elif BOTH(LCD_BED_LEVELING, PROBE_MANUALLY)
|
||||
#elif ALL(LCD_BED_LEVELING, PROBE_MANUALLY)
|
||||
#error "DWIN_CREALITY_LCD does not support LCD_BED_LEVELING with PROBE_MANUALLY."
|
||||
#endif
|
||||
#elif ENABLED(DWIN_LCD_PROUI)
|
||||
#if !HAS_MEDIA
|
||||
#error "DWIN_LCD_PROUI requires SDSUPPORT to be enabled."
|
||||
#elif EITHER(PID_EDIT_MENU, PID_AUTOTUNE_MENU)
|
||||
#elif ANY(PID_EDIT_MENU, PID_AUTOTUNE_MENU)
|
||||
#error "DWIN_LCD_PROUI does not support PID_EDIT_MENU or PID_AUTOTUNE_MENU."
|
||||
#elif EITHER(MPC_EDIT_MENU, MPC_AUTOTUNE_MENU)
|
||||
#elif ANY(MPC_EDIT_MENU, MPC_AUTOTUNE_MENU)
|
||||
#error "DWIN_LCD_PROUI does not support MPC_EDIT_MENU or MPC_AUTOTUNE_MENU."
|
||||
#elif ENABLED(LCD_BED_TRAMMING)
|
||||
#error "DWIN_LCD_PROUI does not support LCD_BED_TRAMMING."
|
||||
#elif BOTH(LCD_BED_LEVELING, PROBE_MANUALLY)
|
||||
#elif ALL(LCD_BED_LEVELING, PROBE_MANUALLY)
|
||||
#error "DWIN_LCD_PROUI does not support LCD_BED_LEVELING with PROBE_MANUALLY."
|
||||
#endif
|
||||
#endif
|
||||
@@ -2735,9 +2735,9 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
|
||||
// Startup Tune requirements
|
||||
#ifdef STARTUP_TUNE
|
||||
#if EITHER(ANYCUBIC_LCD_CHIRON, ANYCUBIC_LCD_VYPER)
|
||||
#if ANY(ANYCUBIC_LCD_CHIRON, ANYCUBIC_LCD_VYPER)
|
||||
#error "STARTUP_TUNE should be disabled with ANYCUBIC_LCD_CHIRON or ANYCUBIC_LCD_VYPER."
|
||||
#elif !(BOTH(HAS_BEEPER, SPEAKER) || USE_MARLINUI_BUZZER)
|
||||
#elif !(ALL(HAS_BEEPER, SPEAKER) || USE_MARLINUI_BUZZER)
|
||||
#error "STARTUP_TUNE requires a BEEPER_PIN with SPEAKER or USE_MARLINUI_BUZZER."
|
||||
#undef STARTUP_TUNE
|
||||
#endif
|
||||
@@ -3232,7 +3232,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
|
||||
#endif // !SPI_ENDSTOPS
|
||||
|
||||
#if ENABLED(DELTA) && !BOTH(STEALTHCHOP_XY, STEALTHCHOP_Z)
|
||||
#if ENABLED(DELTA) && !ALL(STEALTHCHOP_XY, STEALTHCHOP_Z)
|
||||
#error "SENSORLESS_HOMING on DELTA currently requires STEALTHCHOP_XY and STEALTHCHOP_Z."
|
||||
#elif ENDSTOP_NOISE_THRESHOLD
|
||||
#error "SENSORLESS_HOMING is incompatible with ENDSTOP_NOISE_THRESHOLD."
|
||||
@@ -3262,7 +3262,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
#error "CoreXZ requires both X and Z to use sensorless homing if either one does."
|
||||
#elif CORE_IS_YZ && Y_SENSORLESS != Z_SENSORLESS && !HOMING_Z_WITH_PROBE
|
||||
#error "CoreYZ requires both Y and Z to use sensorless homing if either one does."
|
||||
#elif EITHER(MARKFORGED_XY, MARKFORGED_YX) && X_SENSORLESS != Y_SENSORLESS
|
||||
#elif ANY(MARKFORGED_XY, MARKFORGED_YX) && X_SENSORLESS != Y_SENSORLESS
|
||||
#error "MARKFORGED requires both X and Y to use sensorless homing if either one does."
|
||||
#endif
|
||||
|
||||
@@ -3350,7 +3350,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
|
||||
* Digipot requirement
|
||||
*/
|
||||
#if HAS_MOTOR_CURRENT_I2C
|
||||
#if BOTH(DIGIPOT_MCP4018, DIGIPOT_MCP4451)
|
||||
#if ALL(DIGIPOT_MCP4018, DIGIPOT_MCP4451)
|
||||
#error "Enable only one of DIGIPOT_MCP4018 or DIGIPOT_MCP4451."
|
||||
#elif !MB(MKS_SBASE, AZTEEG_X5_GT, AZTEEG_X5_MINI, AZTEEG_X5_MINI_WIFI) \
|
||||
&& (!defined(DIGIPOTS_I2C_SDA_X) || !defined(DIGIPOTS_I2C_SDA_Y) || !defined(DIGIPOTS_I2C_SDA_Z) || !defined(DIGIPOTS_I2C_SDA_E0) || !defined(DIGIPOTS_I2C_SDA_E1))
|
||||
@@ -3423,7 +3423,7 @@ static_assert(_PLUS_TEST(3), "DEFAULT_MAX_ACCELERATION values must be positive."
|
||||
#undef _PLUS_TEST
|
||||
#undef _EXTRA_NOTE
|
||||
|
||||
#if BOTH(CNC_COORDINATE_SYSTEMS, NO_WORKSPACE_OFFSETS)
|
||||
#if ALL(CNC_COORDINATE_SYSTEMS, NO_WORKSPACE_OFFSETS)
|
||||
#error "CNC_COORDINATE_SYSTEMS is incompatible with NO_WORKSPACE_OFFSETS."
|
||||
#endif
|
||||
|
||||
@@ -3459,18 +3459,18 @@ static_assert(_PLUS_TEST(3), "DEFAULT_MAX_ACCELERATION values must be positive."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if BOTH(X_AXIS_TWIST_COMPENSATION, NOZZLE_AS_PROBE)
|
||||
#if ALL(X_AXIS_TWIST_COMPENSATION, NOZZLE_AS_PROBE)
|
||||
#error "X_AXIS_TWIST_COMPENSATION is incompatible with NOZZLE_AS_PROBE."
|
||||
#endif
|
||||
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
#if ENABLED(BACKUP_POWER_SUPPLY) && !PIN_EXISTS(POWER_LOSS)
|
||||
#error "BACKUP_POWER_SUPPLY requires a POWER_LOSS_PIN."
|
||||
#elif BOTH(POWER_LOSS_PULLUP, POWER_LOSS_PULLDOWN)
|
||||
#elif ALL(POWER_LOSS_PULLUP, POWER_LOSS_PULLDOWN)
|
||||
#error "You can't enable POWER_LOSS_PULLUP and POWER_LOSS_PULLDOWN at the same time."
|
||||
#elif ENABLED(POWER_LOSS_RECOVER_ZHOME) && Z_HOME_TO_MAX
|
||||
#error "POWER_LOSS_RECOVER_ZHOME is not needed on a machine that homes to ZMAX."
|
||||
#elif BOTH(IS_CARTESIAN, POWER_LOSS_RECOVER_ZHOME) && Z_HOME_TO_MIN && !defined(POWER_LOSS_ZHOME_POS)
|
||||
#elif ALL(IS_CARTESIAN, POWER_LOSS_RECOVER_ZHOME) && Z_HOME_TO_MIN && !defined(POWER_LOSS_ZHOME_POS)
|
||||
#error "POWER_LOSS_RECOVER_ZHOME requires POWER_LOSS_ZHOME_POS for a Cartesian that homes to ZMIN."
|
||||
#endif
|
||||
#endif
|
||||
@@ -3532,7 +3532,7 @@ static_assert(_PLUS_TEST(3), "DEFAULT_MAX_ACCELERATION values must be positive."
|
||||
#error "BACKLASH_COMPENSATION requires BACKLASH_DISTANCE_MM."
|
||||
#elif !defined(BACKLASH_CORRECTION)
|
||||
#error "BACKLASH_COMPENSATION requires BACKLASH_CORRECTION."
|
||||
#elif EITHER(MARKFORGED_XY, MARKFORGED_YX)
|
||||
#elif ANY(MARKFORGED_XY, MARKFORGED_YX)
|
||||
constexpr float backlash_arr[] = BACKLASH_DISTANCE_MM;
|
||||
static_assert(!backlash_arr[CORE_AXIS_1] && !backlash_arr[CORE_AXIS_2],
|
||||
"BACKLASH_COMPENSATION can only apply to " STRINGIFY(NORMAL_AXIS) " on a MarkForged system.");
|
||||
@@ -3582,7 +3582,7 @@ static_assert(_PLUS_TEST(3), "DEFAULT_MAX_ACCELERATION values must be positive."
|
||||
/**
|
||||
* Require soft endstops for certain setups
|
||||
*/
|
||||
#if !BOTH(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
|
||||
#if !ALL(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
|
||||
#if ENABLED(DUAL_X_CARRIAGE)
|
||||
#error "DUAL_X_CARRIAGE requires both MIN_ and MAX_SOFTWARE_ENDSTOPS."
|
||||
#elif HAS_HOTEND_OFFSET
|
||||
@@ -3643,7 +3643,7 @@ static_assert(_PLUS_TEST(3), "DEFAULT_MAX_ACCELERATION values must be positive."
|
||||
#endif
|
||||
|
||||
#define _PIN_CONFLICT(P) (PIN_EXISTS(P) && P##_PIN == SPINDLE_LASER_PWM_PIN)
|
||||
#if BOTH(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#if ALL(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#error "Enable only one of SPINDLE_FEATURE or LASER_FEATURE."
|
||||
#elif NONE(SPINDLE_SERVO, SPINDLE_LASER_USE_PWM) && !PIN_EXISTS(SPINDLE_LASER_ENA)
|
||||
#error "(SPINDLE|LASER)_FEATURE requires SPINDLE_LASER_ENA_PIN, SPINDLE_LASER_USE_PWM, or SPINDLE_SERVO to control the power."
|
||||
@@ -3792,7 +3792,7 @@ static_assert(_PLUS_TEST(3), "DEFAULT_MAX_ACCELERATION values must be positive."
|
||||
#error "ESP3D_WIFISUPPORT requires an ESP32 MOTHERBOARD."
|
||||
#elif ENABLED(WEBSUPPORT) && NONE(ARDUINO_ARCH_ESP32, WIFISUPPORT)
|
||||
#error "WEBSUPPORT requires WIFISUPPORT and an ESP32 MOTHERBOARD."
|
||||
#elif BOTH(ESP3D_WIFISUPPORT, WIFISUPPORT)
|
||||
#elif ALL(ESP3D_WIFISUPPORT, WIFISUPPORT)
|
||||
#error "Enable only one of ESP3D_WIFISUPPORT or WIFISUPPORT."
|
||||
#endif
|
||||
|
||||
@@ -3810,14 +3810,14 @@ static_assert(_PLUS_TEST(3), "DEFAULT_MAX_ACCELERATION values must be positive."
|
||||
/**
|
||||
* Sanity Check for MEATPACK and BINARY_FILE_TRANSFER Features
|
||||
*/
|
||||
#if BOTH(HAS_MEATPACK, BINARY_FILE_TRANSFER)
|
||||
#if ALL(HAS_MEATPACK, BINARY_FILE_TRANSFER)
|
||||
#error "Either enable MEATPACK_ON_SERIAL_PORT_* or BINARY_FILE_TRANSFER, not both."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Sanity Check for Slim LCD Menus and Probe Offset Wizard
|
||||
*/
|
||||
#if BOTH(SLIM_LCD_MENUS, PROBE_OFFSET_WIZARD)
|
||||
#if ALL(SLIM_LCD_MENUS, PROBE_OFFSET_WIZARD)
|
||||
#error "SLIM_LCD_MENUS disables \"Advanced Settings > Probe Offsets > PROBE_OFFSET_WIZARD.\""
|
||||
#endif
|
||||
|
||||
@@ -3854,7 +3854,7 @@ static_assert(_PLUS_TEST(3), "DEFAULT_MAX_ACCELERATION values must be positive."
|
||||
/**
|
||||
* Sanity check for MIXING_EXTRUDER & DISTINCT_E_FACTORS these are not compatible
|
||||
*/
|
||||
#if BOTH(MIXING_EXTRUDER, DISTINCT_E_FACTORS)
|
||||
#if ALL(MIXING_EXTRUDER, DISTINCT_E_FACTORS)
|
||||
#error "MIXING_EXTRUDER can't be used with DISTINCT_E_FACTORS. But you may use SINGLENOZZLE with DISTINCT_E_FACTORS."
|
||||
#endif
|
||||
|
||||
@@ -3988,7 +3988,7 @@ static_assert(_PLUS_TEST(3), "DEFAULT_MAX_ACCELERATION values must be positive."
|
||||
#endif
|
||||
|
||||
// Check requirements for upload.py
|
||||
#if ENABLED(XFER_BUILD) && !BOTH(BINARY_FILE_TRANSFER, CUSTOM_FIRMWARE_UPLOAD)
|
||||
#if ENABLED(XFER_BUILD) && !ALL(BINARY_FILE_TRANSFER, CUSTOM_FIRMWARE_UPLOAD)
|
||||
#error "BINARY_FILE_TRANSFER and CUSTOM_FIRMWARE_UPLOAD are required for custom upload."
|
||||
#endif
|
||||
|
||||
@@ -4008,12 +4008,12 @@ static_assert(_PLUS_TEST(3), "DEFAULT_MAX_ACCELERATION values must be positive."
|
||||
#error "Input Shaping is not compatible with POLARGRAPH kinematics."
|
||||
#elif ENABLED(DIRECT_STEPPING)
|
||||
#error "Input Shaping is not compatible with DIRECT_STEPPING."
|
||||
#elif BOTH(INPUT_SHAPING_X, CORE_IS_XZ)
|
||||
#elif ALL(INPUT_SHAPING_X, CORE_IS_XZ)
|
||||
#error "INPUT_SHAPING_X is not supported with COREXZ."
|
||||
#elif BOTH(INPUT_SHAPING_Y, CORE_IS_YZ)
|
||||
#elif ALL(INPUT_SHAPING_Y, CORE_IS_YZ)
|
||||
#error "INPUT_SHAPING_Y is not supported with COREYZ."
|
||||
#elif ANY(CORE_IS_XY, MARKFORGED_XY, MARKFORGED_YX)
|
||||
#if !BOTH(INPUT_SHAPING_X, INPUT_SHAPING_Y)
|
||||
#if !ALL(INPUT_SHAPING_X, INPUT_SHAPING_Y)
|
||||
#error "INPUT_SHAPING_X and INPUT_SHAPING_Y must both be enabled for COREXY, COREYX, or MARKFORGED_*."
|
||||
#else
|
||||
static_assert(SHAPING_FREQ_X == SHAPING_FREQ_Y, "SHAPING_FREQ_X and SHAPING_FREQ_Y must be the same for COREXY / COREYX / MARKFORGED_*.");
|
||||
|
||||
Reference in New Issue
Block a user