FFCP updates. Update XY soft endstops on tool_change (#14125)
This commit is contained in:
mikeshub
Scott Lahteine
@ -124,7 +124,7 @@
|
||||
*
|
||||
* :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
|
||||
*/
|
||||
#define BAUDRATE 115200
|
||||
#define BAUDRATE 250000
|
||||
|
||||
// Enable the Bluetooth serial interface on AT90USB devices
|
||||
//#define BLUETOOTH
|
||||
@ -294,8 +294,8 @@
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
// For the other hotends it is their distance from the extruder 0 hotend.
|
||||
#define HOTEND_OFFSET_X {0.0, -33.00} // (mm) relative X-offset for each nozzle
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (mm) relative Y-offset for each nozzle
|
||||
//#define HOTEND_OFFSET_X {0.0, -34.00} // (mm) relative X-offset for each nozzle
|
||||
//#define HOTEND_OFFSET_Y {0.0, 0.00} // (mm) relative Y-offset for each nozzle
|
||||
//#define HOTEND_OFFSET_Z {0.0, 0.00} // (mm) relative Z-offset for each nozzle
|
||||
|
||||
// @section machine
|
||||
@ -405,11 +405,11 @@
|
||||
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||||
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
|
||||
|
||||
#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
|
||||
#define TEMP_RESIDENCY_TIME 0 // (seconds) Time to wait for hotend to "settle" in M109
|
||||
#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
|
||||
|
||||
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
|
||||
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
|
||||
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
|
||||
|
||||
@ -452,7 +452,7 @@
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 15 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
@ -699,7 +699,7 @@
|
||||
* Override with M203
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 500, 500, 20, 25 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 250, 250, 20, 100 }
|
||||
|
||||
/**
|
||||
* Default Max Acceleration (change/s) change = mm/s
|
||||
@ -707,7 +707,7 @@
|
||||
* Override with M201
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
|
||||
*/
|
||||
#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 100, 80000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 100, 5000 }
|
||||
|
||||
/**
|
||||
* Default Acceleration (change/s) change = mm/s
|
||||
@ -717,9 +717,9 @@
|
||||
* M204 R Retract Acceleration
|
||||
* M204 T Travel Acceleration
|
||||
*/
|
||||
#define DEFAULT_ACCELERATION 1750 // X, Y, Z and E max acceleration for printing moves
|
||||
#define DEFAULT_ACCELERATION 250 // X, Y, Z and E max acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
//
|
||||
// Use Junction Deviation instead of traditional Jerk Limiting
|
||||
@ -743,7 +743,7 @@
|
||||
#define DEFAULT_ZJERK 0.4
|
||||
#endif
|
||||
|
||||
#define DEFAULT_EJERK 5.0 // May be used by Linear Advance
|
||||
#define DEFAULT_EJERK 2.0 // May be used by Linear Advance
|
||||
|
||||
/**
|
||||
* S-Curve Acceleration
|
||||
@ -970,7 +970,7 @@
|
||||
|
||||
//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
|
||||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
@ -989,7 +989,7 @@
|
||||
#define Y_BED_SIZE 148
|
||||
|
||||
// Travel limits (mm) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS -120
|
||||
#define X_MIN_POS -115
|
||||
#define Y_MIN_POS -84
|
||||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS 152
|
||||
@ -1351,11 +1351,11 @@
|
||||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
//#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
#endif
|
||||
|
||||
//
|
||||
@ -1387,13 +1387,13 @@
|
||||
|
||||
// Preheat Constants
|
||||
#define PREHEAT_1_LABEL "PLA"
|
||||
#define PREHEAT_1_TEMP_HOTEND 180
|
||||
#define PREHEAT_1_TEMP_BED 70
|
||||
#define PREHEAT_1_TEMP_HOTEND 200
|
||||
#define PREHEAT_1_TEMP_BED 50
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
#define PREHEAT_2_LABEL "ABS"
|
||||
#define PREHEAT_2_TEMP_HOTEND 240
|
||||
#define PREHEAT_2_TEMP_BED 110
|
||||
#define PREHEAT_2_TEMP_HOTEND 220
|
||||
#define PREHEAT_2_TEMP_BED 100
|
||||
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
/**
|
||||
@ -1507,7 +1507,7 @@
|
||||
*
|
||||
* View the current statistics with M78.
|
||||
*/
|
||||
//#define PRINTCOUNTER
|
||||
#define PRINTCOUNTER
|
||||
|
||||
//=============================================================================
|
||||
//============================= LCD and SD support ============================
|
||||
@ -1582,7 +1582,7 @@
|
||||
*
|
||||
* Use CRC checks and retries on the SD communication.
|
||||
*/
|
||||
//#define SD_CHECK_AND_RETRY
|
||||
#define SD_CHECK_AND_RETRY
|
||||
|
||||
/**
|
||||
* LCD Menu Items
|
||||
@ -1637,7 +1637,7 @@
|
||||
//
|
||||
// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
|
||||
//
|
||||
//#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
|
||||
//
|
||||
// SPEAKER/BUZZER
|
||||
|
||||
Reference in New Issue
Block a user