Add NUM_RUNOUT_SENSORS to example configs

Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h

@@ -850,15 +850,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/AliExpress/CL-260/Configuration.h

@@ -830,15 +830,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Anet/A6/Configuration.h

@@ -940,15 +940,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Anet/A8/Configuration.h

@@ -837,15 +837,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/BIBO/TouchX/Cyclops/Configuration.h

@@ -830,15 +830,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/BIBO/TouchX/default/Configuration.h

@@ -830,15 +830,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/BQ/Hephestos/Configuration.h

@@ -818,15 +818,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/BQ/Hephestos_2/Configuration.h

@@ -831,15 +831,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/BQ/WITBOX/Configuration.h

@@ -818,15 +818,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Cartesio/Configuration.h

@@ -829,15 +829,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Creality/CR-10/Configuration.h

@@ -840,15 +840,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Creality/CR-10S/Configuration.h

@@ -829,15 +829,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING true // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Creality/Ender/Configuration.h

@@ -833,15 +833,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Felix/Configuration.h

@@ -812,15 +812,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -812,15 +812,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h

@@ -844,15 +844,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Geeetech/GT2560/Configuration.h

@@ -845,15 +845,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -830,15 +830,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -837,15 +837,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -836,15 +836,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Infitary/i3-M508/Configuration.h

@@ -834,15 +834,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/JGAurora/A5/Configuration.h

@@ -842,15 +842,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Malyan/M150/Configuration.h

@@ -854,15 +854,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Micromake/C1/basic/Configuration.h

@@ -834,15 +834,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h

@@ -834,15 +834,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -830,15 +830,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/RigidBot/Configuration.h

@@ -828,15 +828,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/SCARA/Configuration.h

@@ -842,15 +842,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Sanguinololu/Configuration.h

@@ -861,15 +861,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/TinyBoy2/Configuration.h

@@ -886,15 +886,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Tronxy/X1/Configuration.h

@@ -829,15 +829,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Tronxy/X5S/Configuration.h

@@ -830,15 +830,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Tronxy/XY100/Configuration.h

@@ -841,15 +841,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Velleman/K8200/Configuration.h

@@ -860,15 +860,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Velleman/K8400/Configuration.h

@@ -830,15 +830,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h

@@ -830,15 +830,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h

@@ -840,15 +840,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -830,15 +830,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h

@@ -960,15 +960,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/delta/FLSUN/kossel/Configuration.h

@@ -959,15 +959,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h

@@ -960,15 +960,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/delta/generic/Configuration.h

@@ -947,15 +947,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -950,15 +950,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -950,15 +950,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -959,15 +959,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h

@@ -844,15 +844,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/makibox/Configuration.h

@@ -833,15 +833,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -825,15 +825,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"

Marlin/example_configurations/wt150/Configuration.h

@@ -835,15 +835,16 @@
 #endif
 
 /**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
  *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   #define FILAMENT_RUNOUT_SCRIPT "M600"