diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index b3f43b4c2d..54a719885e 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -690,14 +690,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index b1095f8e12..4efb07f722 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 12c0da6ceb..2bddfa24ef 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -2215,7 +2215,7 @@ static void clean_up_after_endstop_or_probe_move() {
   }
 
   /**
-   * @details Used by probe_pt to do a single Z probe.
+   * @details Used by probe_pt to do a single Z probe at the current position.
    *          Leaves current_position[Z_AXIS] at the height where the probe triggered.
    *
    * @return The raw Z position where the probe was triggered
@@ -2229,7 +2229,8 @@ static void clean_up_after_endstop_or_probe_move() {
     // Prevent stepper_inactive_time from running out and EXTRUDER_RUNOUT_PREVENT from extruding
     refresh_cmd_timeout();
 
-    #if ENABLED(PROBE_DOUBLE_TOUCH)
+    // Double-probing does a fast probe followed by a slow probe
+    #if MULTIPLE_PROBING == 2
 
       // Do a first probe at the fast speed
       if (do_probe_move(-10, Z_PROBE_SPEED_FAST)) return NAN;
@@ -2257,22 +2258,49 @@ static void clean_up_after_endstop_or_probe_move() {
       }
     #endif
 
-    // move down slowly to find bed
-    if (do_probe_move(-10, Z_PROBE_SPEED_SLOW)) return NAN;
+    #if MULTIPLE_PROBING > 2
+      float probes_total = 0;
+      for (uint8_t p = MULTIPLE_PROBING + 1; --p;) {
+    #endif
+
+        // move down slowly to find bed
+        if (do_probe_move(-10, Z_PROBE_SPEED_SLOW)) return NAN;
+
+    #if MULTIPLE_PROBING > 2
+        probes_total += current_position[Z_AXIS];
+        if (p > 1) do_blocking_move_to_z(current_position[Z_AXIS] + Z_CLEARANCE_BETWEEN_PROBES, MMM_TO_MMS(Z_PROBE_SPEED_FAST));
+      }
+    #endif
+
+    #if MULTIPLE_PROBING > 2
+
+      // Return the average value of all probes
+      return probes_total * (1.0 / (MULTIPLE_PROBING));
+
+    #elif MULTIPLE_PROBING == 2
+
+      const float z2 = current_position[Z_AXIS];
+
+      #if ENABLED(DEBUG_LEVELING_FEATURE)
+        if (DEBUGGING(LEVELING)) {
+          SERIAL_ECHOPAIR("2nd Probe Z:", z2);
+          SERIAL_ECHOLNPAIR(" Discrepancy:", first_probe_z - z2);
+        }
+      #endif
+
+      // Return a weighted average of the fast and slow probes
+      return (z2 * 3.0 + first_probe_z * 2.0) * 0.2;
+
+    #else
+
+      // Return the single probe result
+      return current_position[Z_AXIS];
+
+    #endif
 
     #if ENABLED(DEBUG_LEVELING_FEATURE)
       if (DEBUGGING(LEVELING)) DEBUG_POS("<<< run_z_probe", current_position);
     #endif
-
-    // Debug: compare probe heights
-    #if ENABLED(PROBE_DOUBLE_TOUCH) && ENABLED(DEBUG_LEVELING_FEATURE)
-      if (DEBUGGING(LEVELING)) {
-        SERIAL_ECHOPAIR("2nd Probe Z:", current_position[Z_AXIS]);
-        SERIAL_ECHOLNPAIR(" Discrepancy:", first_probe_z - current_position[Z_AXIS]);
-      }
-    #endif
-
-    return current_position[Z_AXIS];
   }
 
   /**
@@ -6005,7 +6033,7 @@ void home_all_axes() { gcode_G28(true); }
 
     bool G38_pass_fail = false;
 
-    #if ENABLED(PROBE_DOUBLE_TOUCH)
+    #if MULTIPLE_PROBING > 1
       // Get direction of move and retract
       float retract_mm[XYZ];
       LOOP_XYZ(i) {
@@ -6032,7 +6060,7 @@ void home_all_axes() { gcode_G28(true); }
 
       G38_pass_fail = true;
 
-      #if ENABLED(PROBE_DOUBLE_TOUCH)
+      #if MULTIPLE_PROBING > 1
         // Move away by the retract distance
         set_destination_from_current();
         LOOP_XYZ(i) destination[i] += retract_mm[i];
diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h
index 2d5c706fcb..1f9dccc36b 100644
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@@ -224,6 +224,8 @@
   #error "UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN is now SEGMENT_LEVELED_MOVES. Please update your configuration."
 #elif HAS_PID_HEATING && (defined(K1) || !defined(PID_K1))
   #error "K1 is now PID_K1. Please update your configuration."
+#elif defined(PROBE_DOUBLE_TOUCH)
+  #error "PROBE_DOUBLE_TOUCH is now MULTIPLE_PROBING. Please update your configuration."
 #endif
 
 /**
@@ -698,6 +700,10 @@ static_assert(1 >= 0
     #error "Probes need Z_CLEARANCE_BETWEEN_PROBES >= 0."
   #endif
 
+  #if MULTIPLE_PROBING && MULTIPLE_PROBING < 2
+    #error "MULTIPLE_PROBING must be >= 2."
+  #endif
+
 #else
 
   /**
diff --git a/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h b/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h
index 9418f7f47c..c2bda49fe7 100644
--- a/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h
@@ -710,14 +710,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h
index f83ebeaa27..1f8602dff9 100644
--- a/Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/AliExpress/CL-260/Configuration.h b/Marlin/example_configurations/AliExpress/CL-260/Configuration.h
index 20aa9ba542..acf3b2c2c6 100644
--- a/Marlin/example_configurations/AliExpress/CL-260/Configuration.h
+++ b/Marlin/example_configurations/AliExpress/CL-260/Configuration.h
@@ -690,14 +690,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Anet/A6/Configuration.h b/Marlin/example_configurations/Anet/A6/Configuration.h
index cc82e88bdb..99843e3efb 100644
--- a/Marlin/example_configurations/Anet/A6/Configuration.h
+++ b/Marlin/example_configurations/Anet/A6/Configuration.h
@@ -769,14 +769,16 @@
 #define XY_PROBE_SPEED 8000
 //#define XY_PROBE_SPEED 6000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 3)
 
-// Use double touch for probing
-#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Anet/A6/Configuration_adv.h b/Marlin/example_configurations/Anet/A6/Configuration_adv.h
index a5c53df43c..581cfaf0b4 100644
--- a/Marlin/example_configurations/Anet/A6/Configuration_adv.h
+++ b/Marlin/example_configurations/Anet/A6/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Anet/A8/Configuration.h b/Marlin/example_configurations/Anet/A8/Configuration.h
index 55843fc273..f0e0150ee0 100644
--- a/Marlin/example_configurations/Anet/A8/Configuration.h
+++ b/Marlin/example_configurations/Anet/A8/Configuration.h
@@ -697,14 +697,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 6000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Anet/A8/Configuration_adv.h b/Marlin/example_configurations/Anet/A8/Configuration_adv.h
index a176761ebc..9537b22471 100644
--- a/Marlin/example_configurations/Anet/A8/Configuration_adv.h
+++ b/Marlin/example_configurations/Anet/A8/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/BQ/Hephestos/Configuration.h b/Marlin/example_configurations/BQ/Hephestos/Configuration.h
index 6a908de4d5..6a844afba8 100644
--- a/Marlin/example_configurations/BQ/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/BQ/Hephestos/Configuration.h
@@ -681,14 +681,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h b/Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h
index 7b98a75a93..6d93dd138f 100644
--- a/Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h b/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h
index cd2cb05e7d..0e9f08d411 100644
--- a/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h
@@ -691,14 +691,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h
index 3f77a3065b..8a5f3e7720 100644
--- a/Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/BQ/WITBOX/Configuration.h b/Marlin/example_configurations/BQ/WITBOX/Configuration.h
index 4bfd3a3822..727e83cd77 100644
--- a/Marlin/example_configurations/BQ/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/BQ/WITBOX/Configuration.h
@@ -681,14 +681,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h b/Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h
index 7b98a75a93..6d93dd138f 100644
--- a/Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Cartesio/Configuration.h b/Marlin/example_configurations/Cartesio/Configuration.h
index eccef8aec9..a1b391bf0d 100644
--- a/Marlin/example_configurations/Cartesio/Configuration.h
+++ b/Marlin/example_configurations/Cartesio/Configuration.h
@@ -689,14 +689,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Cartesio/Configuration_adv.h b/Marlin/example_configurations/Cartesio/Configuration_adv.h
index 2c138d3c17..fa6d2b55d1 100644
--- a/Marlin/example_configurations/Cartesio/Configuration_adv.h
+++ b/Marlin/example_configurations/Cartesio/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Creality/CR-10/Configuration.h b/Marlin/example_configurations/Creality/CR-10/Configuration.h
index 18019bad83..200619a773 100755
--- a/Marlin/example_configurations/Creality/CR-10/Configuration.h
+++ b/Marlin/example_configurations/Creality/CR-10/Configuration.h
@@ -700,14 +700,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Creality/CR-10/Configuration_adv.h b/Marlin/example_configurations/Creality/CR-10/Configuration_adv.h
index 40fcca7276..044def3a4f 100755
--- a/Marlin/example_configurations/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/example_configurations/Creality/CR-10/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h
index 789f251159..5920f97cdb 100644
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@@ -672,14 +672,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h
index 29b2845ed0..1c925bb8c5 100644
--- a/Marlin/example_configurations/Felix/Configuration_adv.h
+++ b/Marlin/example_configurations/Felix/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h
index 5758bb9ef0..350785f160 100644
--- a/Marlin/example_configurations/Felix/DUAL/Configuration.h
+++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h
@@ -672,14 +672,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h b/Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h
index 35976de17b..6aefbc00e1 100644
--- a/Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h
+++ b/Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h
@@ -694,14 +694,16 @@
 
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 7500
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/FolgerTech/i3-2020/Configuration_adv.h b/Marlin/example_configurations/FolgerTech/i3-2020/Configuration_adv.h
index 31cccde0be..af44462f66 100644
--- a/Marlin/example_configurations/FolgerTech/i3-2020/Configuration_adv.h
+++ b/Marlin/example_configurations/FolgerTech/i3-2020/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Geeetech/GT2560/Configuration.h b/Marlin/example_configurations/Geeetech/GT2560/Configuration.h
index e2d6b16075..4acbde91ce 100644
--- a/Marlin/example_configurations/Geeetech/GT2560/Configuration.h
+++ b/Marlin/example_configurations/Geeetech/GT2560/Configuration.h
@@ -705,14 +705,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h
index 02f4467133..3c36f6d79b 100644
--- a/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -690,14 +690,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Infitary/i3-M508/Configuration.h b/Marlin/example_configurations/Infitary/i3-M508/Configuration.h
index d21d3bbd87..2f39fcc912 100644
--- a/Marlin/example_configurations/Infitary/i3-M508/Configuration.h
+++ b/Marlin/example_configurations/Infitary/i3-M508/Configuration.h
@@ -694,14 +694,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h b/Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h
index 5c86932cb5..020cd1f2cf 100644
--- a/Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Malyan/M150/Configuration.h b/Marlin/example_configurations/Malyan/M150/Configuration.h
index 841cce6774..3d23a8a105 100644
--- a/Marlin/example_configurations/Malyan/M150/Configuration.h
+++ b/Marlin/example_configurations/Malyan/M150/Configuration.h
@@ -714,14 +714,16 @@
 // X and Y axis travel speed (mm/m) between probes
 //#define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 //#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 //#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Malyan/M150/Configuration_adv.h b/Marlin/example_configurations/Malyan/M150/Configuration_adv.h
index 60f1d8de24..925395758c 100644
--- a/Marlin/example_configurations/Malyan/M150/Configuration_adv.h
+++ b/Marlin/example_configurations/Malyan/M150/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Micromake/C1/basic/Configuration.h b/Marlin/example_configurations/Micromake/C1/basic/Configuration.h
index d8b375a3c0..9ec5ef7a89 100644
--- a/Marlin/example_configurations/Micromake/C1/basic/Configuration.h
+++ b/Marlin/example_configurations/Micromake/C1/basic/Configuration.h
@@ -694,14 +694,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h b/Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h
index 5de6a703ed..13971ed928 100644
--- a/Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h
+++ b/Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h
@@ -694,14 +694,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Micromake/C1/enhanced/Configuration_adv.h b/Marlin/example_configurations/Micromake/C1/enhanced/Configuration_adv.h
index dcd1dd67ec..c0b33fe7b2 100644
--- a/Marlin/example_configurations/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/example_configurations/Micromake/C1/enhanced/Configuration_adv.h
@@ -743,7 +743,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
index 5450c018fc..c239bfe5cc 100644
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@@ -690,14 +690,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h
index 058278fa6e..8172df219b 100644
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@@ -688,14 +688,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h
index 5dd79f5c0e..8dd1170f37 100644
--- a/Marlin/example_configurations/RigidBot/Configuration_adv.h
+++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index febe7874fa..0c6746500b 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -702,14 +702,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h
index ecbc3e5148..bca1fa4b40 100644
--- a/Marlin/example_configurations/SCARA/Configuration_adv.h
+++ b/Marlin/example_configurations/SCARA/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Sanguinololu/Configuration.h b/Marlin/example_configurations/Sanguinololu/Configuration.h
index 0c5af413df..96100eecd1 100644
--- a/Marlin/example_configurations/Sanguinololu/Configuration.h
+++ b/Marlin/example_configurations/Sanguinololu/Configuration.h
@@ -721,14 +721,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Sanguinololu/Configuration_adv.h b/Marlin/example_configurations/Sanguinololu/Configuration_adv.h
index 038d1a0bf0..29cb9ee931 100644
--- a/Marlin/example_configurations/Sanguinololu/Configuration_adv.h
+++ b/Marlin/example_configurations/Sanguinololu/Configuration_adv.h
@@ -731,7 +731,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/TinyBoy2/Configuration.h b/Marlin/example_configurations/TinyBoy2/Configuration.h
index 2b5531ae25..b80f058557 100644
--- a/Marlin/example_configurations/TinyBoy2/Configuration.h
+++ b/Marlin/example_configurations/TinyBoy2/Configuration.h
@@ -741,14 +741,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/TinyBoy2/Configuration_adv.h b/Marlin/example_configurations/TinyBoy2/Configuration_adv.h
index 09e5443de2..d63224cee4 100644
--- a/Marlin/example_configurations/TinyBoy2/Configuration_adv.h
+++ b/Marlin/example_configurations/TinyBoy2/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Velleman/K8200/Configuration.h b/Marlin/example_configurations/Velleman/K8200/Configuration.h
index 16d46f1b9c..bcb393d864 100644
--- a/Marlin/example_configurations/Velleman/K8200/Configuration.h
+++ b/Marlin/example_configurations/Velleman/K8200/Configuration.h
@@ -719,14 +719,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Velleman/K8200/Configuration_adv.h b/Marlin/example_configurations/Velleman/K8200/Configuration_adv.h
index c0da1d6859..13566af07b 100644
--- a/Marlin/example_configurations/Velleman/K8200/Configuration_adv.h
+++ b/Marlin/example_configurations/Velleman/K8200/Configuration_adv.h
@@ -753,7 +753,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Velleman/K8400/Configuration.h b/Marlin/example_configurations/Velleman/K8400/Configuration.h
index 98b6a51b29..b8aa5e86b2 100644
--- a/Marlin/example_configurations/Velleman/K8400/Configuration.h
+++ b/Marlin/example_configurations/Velleman/K8400/Configuration.h
@@ -690,14 +690,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Velleman/K8400/Configuration_adv.h b/Marlin/example_configurations/Velleman/K8400/Configuration_adv.h
index f84742c5ca..6206688ec6 100644
--- a/Marlin/example_configurations/Velleman/K8400/Configuration_adv.h
+++ b/Marlin/example_configurations/Velleman/K8400/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h b/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h
index 91c42f784c..045dd6cd64 100644
--- a/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h
+++ b/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h
@@ -690,14 +690,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h b/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h
index 67c1f1eb9c..531a6a8270 100644
--- a/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h	
+++ b/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h	
@@ -700,14 +700,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration_adv.h b/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration_adv.h
index da700d789f..612293dea7 100644
--- a/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration_adv.h	
+++ b/Marlin/example_configurations/Wanhao/Duplicator 6/Configuration_adv.h	
@@ -744,7 +744,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
index b2740b8621..fca4fe7b40 100644
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@@ -690,14 +690,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h
index 057ba49e05..1c8001b24e 100644
--- a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h
@@ -770,14 +770,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 5000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST) / 6
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h
index ac5b68091a..0023bdb43b 100644
--- a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -744,7 +744,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h
index 9d767cd362..86a0cebba2 100644
--- a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h
@@ -770,14 +770,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 2000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+#define MULTIPLE_PROBING 2
 
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
diff --git a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h
index c3c6636efc..bcc226cca7 100644
--- a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -744,7 +744,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index 3cf0d2099d..692a014b45 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -760,14 +760,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 4000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h
index c3c6636efc..bcc226cca7 100644
--- a/Marlin/example_configurations/delta/generic/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h
@@ -744,7 +744,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index 6b672f3dfc..1ea9c6ce23 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -760,14 +760,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 4000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
index c3c6636efc..bcc226cca7 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
@@ -744,7 +744,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
index 09abd744a7..a4c33f5aea 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@@ -756,14 +756,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
index e38f5278e0..503cdbcb17 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
@@ -749,7 +749,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
index fe2667eb5b..f5bed07dcb 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@@ -772,14 +772,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
index 27d3eb95cc..e4e8e83850 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
@@ -744,7 +744,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h b/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h
index 2766613826..5172429631 100644
--- a/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h
+++ b/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h
@@ -703,14 +703,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 7500
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/example_configurations/gCreate/gMax1.5+/Configuration_adv.h
index 30081e0e6b..ed77949771 100644
--- a/Marlin/example_configurations/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/example_configurations/gCreate/gMax1.5+/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index 71d9604d5a..3f1b04d9df 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -693,14 +693,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h
index 7c870a8954..eb18eebcb2 100644
--- a/Marlin/example_configurations/makibox/Configuration_adv.h
+++ b/Marlin/example_configurations/makibox/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index d910be3491..ae0526c72e 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -685,14 +685,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
index 22733d8b1f..fb5aa824b4 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
@@ -742,7 +742,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
diff --git a/Marlin/example_configurations/wt150/Configuration.h b/Marlin/example_configurations/wt150/Configuration.h
index dfb87d5f82..2d79450368 100644
--- a/Marlin/example_configurations/wt150/Configuration.h
+++ b/Marlin/example_configurations/wt150/Configuration.h
@@ -695,14 +695,16 @@
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
 
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+// Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/Marlin/example_configurations/wt150/Configuration_adv.h b/Marlin/example_configurations/wt150/Configuration_adv.h
index acca3e1ac6..8b590cb256 100644
--- a/Marlin/example_configurations/wt150/Configuration_adv.h
+++ b/Marlin/example_configurations/wt150/Configuration_adv.h
@@ -732,7 +732,7 @@
 //#define BEZIER_CURVE_SUPPORT
 
 // G38.2 and G38.3 Probe Target
-// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+// Set MULTIPLE_PROBING if you want G38 to double touch
 //#define G38_PROBE_TARGET
 #if ENABLED(G38_PROBE_TARGET)
   #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)