Keep "astyled" elements in planner.*

Marlin/planner.cpp

@@ -110,7 +110,7 @@ long position[NUM_AXIS];               // Rescaled from extern when axis_steps_p
 static float previous_speed[NUM_AXIS]; // Speed of previous path line segment
 static float previous_nominal_speed;   // Nominal speed of previous path line segment
 
-unsigned char g_uc_extruder_last_move[4] = {0,0,0,0};
+unsigned char g_uc_extruder_last_move[4] = { 0 };
 
 #ifdef XY_FREQUENCY_LIMIT
   // Used for the frequency limit
@@ -118,7 +118,7 @@ unsigned char g_uc_extruder_last_move[4] = {0,0,0,0};
   // Old direction bits. Used for speed calculations
   static unsigned char old_direction_bits = 0;
   // Segment times (in µs). Used for speed calculations
-  static long axis_segment_time[2][3] = { {MAX_FREQ_TIME+1,0,0}, {MAX_FREQ_TIME+1,0,0} };
+  static long axis_segment_time[2][3] = { {MAX_FREQ_TIME + 1, 0, 0}, {MAX_FREQ_TIME + 1, 0, 0} };
 #endif
 
 #if ENABLED(FILAMENT_SENSOR)
@@ -153,7 +153,7 @@ FORCE_INLINE float intersection_distance(float initial_rate, float final_rate, f
 
 // Calculates trapezoid parameters so that the entry- and exit-speed is compensated by the provided factors.
 
-void calculate_trapezoid_for_block(block_t *block, float entry_factor, float exit_factor) {
+void calculate_trapezoid_for_block(block_t* block, float entry_factor, float exit_factor) {
   unsigned long initial_rate = ceil(block->nominal_rate * entry_factor); // (step/min)
   unsigned long final_rate = ceil(block->nominal_rate * exit_factor); // (step/min)
 
@@ -178,17 +178,17 @@ void calculate_trapezoid_for_block(block_t *block, float entry_factor, float exi
     plateau_steps = 0;
   }
 
-#if ENABLED(ADVANCE)
+  #if ENABLED(ADVANCE)
-  volatile long initial_advance = block->advance * entry_factor * entry_factor;
+    volatile long initial_advance = block->advance * entry_factor * entry_factor;
-  volatile long final_advance = block->advance * exit_factor * exit_factor;
+    volatile long final_advance = block->advance * exit_factor * exit_factor;
-#endif // ADVANCE
+  #endif // ADVANCE
 
   // block->accelerate_until = accelerate_steps;
   // block->decelerate_after = accelerate_steps+plateau_steps;
   CRITICAL_SECTION_START;  // Fill variables used by the stepper in a critical section
   if (!block->busy) { // Don't update variables if block is busy.
     block->accelerate_until = accelerate_steps;
-    block->decelerate_after = accelerate_steps+plateau_steps;
+    block->decelerate_after = accelerate_steps + plateau_steps;
     block->initial_rate = initial_rate;
     block->final_rate = final_rate;
     #if ENABLED(ADVANCE)
@@ -215,7 +215,7 @@ FORCE_INLINE float max_allowable_speed(float acceleration, float target_velocity
 
 
 // The kernel called by planner_recalculate() when scanning the plan from last to first entry.
-void planner_reverse_pass_kernel(block_t *previous, block_t *current, block_t *next) {
+void planner_reverse_pass_kernel(block_t* previous, block_t* current, block_t* next) {
   if (!current) return;
   UNUSED(previous);
 
@@ -229,7 +229,7 @@ void planner_reverse_pass_kernel(block_t *previous, block_t *current, block_t *n
       // for max allowable speed if block is decelerating and nominal length is false.
       if (!current->nominal_length_flag && current->max_entry_speed > next->entry_speed) {
         current->entry_speed = min(current->max_entry_speed,
-          max_allowable_speed(-current->acceleration, next->entry_speed, current->millimeters));
+                                   max_allowable_speed(-current->acceleration, next->entry_speed, current->millimeters));
       }
       else {
         current->entry_speed = current->max_entry_speed;
@@ -252,11 +252,11 @@ void planner_reverse_pass() {
 
   if (BLOCK_MOD(block_buffer_head - tail + BLOCK_BUFFER_SIZE) > 3) { // moves queued
     block_index = BLOCK_MOD(block_buffer_head - 3);
-    block_t *block[3] = { NULL, NULL, NULL };
+    block_t* block[3] = { NULL, NULL, NULL };
     while (block_index != tail) {
       block_index = prev_block_index(block_index);
-      block[2]= block[1];
+      block[2] = block[1];
-      block[1]= block[0];
+      block[1] = block[0];
       block[0] = &block_buffer[block_index];
       planner_reverse_pass_kernel(block[0], block[1], block[2]);
     }
@@ -264,7 +264,7 @@ void planner_reverse_pass() {
 }
 
 // The kernel called by planner_recalculate() when scanning the plan from first to last entry.
-void planner_forward_pass_kernel(block_t *previous, block_t *current, block_t *next) {
+void planner_forward_pass_kernel(block_t* previous, block_t* current, block_t* next) {
   if (!previous) return;
   UNUSED(next);
 
@@ -275,8 +275,7 @@ void planner_forward_pass_kernel(block_t *previous, block_t *current, block_t *n
   if (!previous->nominal_length_flag) {
     if (previous->entry_speed < current->entry_speed) {
       double entry_speed = min(current->entry_speed,
-        max_allowable_speed(-previous->acceleration, previous->entry_speed, previous->millimeters));
+                               max_allowable_speed(-previous->acceleration, previous->entry_speed, previous->millimeters));
-
       // Check for junction speed change
       if (current->entry_speed != entry_speed) {
         current->entry_speed = entry_speed;
@@ -290,7 +289,7 @@ void planner_forward_pass_kernel(block_t *previous, block_t *current, block_t *n
 // implements the forward pass.
 void planner_forward_pass() {
   uint8_t block_index = block_buffer_tail;
-  block_t *block[3] = { NULL, NULL, NULL };
+  block_t* block[3] = { NULL, NULL, NULL };
 
   while (block_index != block_buffer_head) {
     block[0] = block[1];
@@ -307,8 +306,8 @@ void planner_forward_pass() {
 // updating the blocks.
 void planner_recalculate_trapezoids() {
   int8_t block_index = block_buffer_tail;
-  block_t *current;
+  block_t* current;
-  block_t *next = NULL;
+  block_t* next = NULL;
 
   while (block_index != block_buffer_head) {
     current = next;
@@ -322,7 +321,7 @@ void planner_recalculate_trapezoids() {
         current->recalculate_flag = false; // Reset current only to ensure next trapezoid is computed
       }
     }
-    block_index = next_block_index( block_index );
+    block_index = next_block_index(block_index);
   }
   // Last/newest block in buffer. Exit speed is set with MINIMUM_PLANNER_SPEED. Always recalculated.
   if (next) {
@@ -358,7 +357,7 @@ void planner_recalculate() {
 void plan_init() {
   block_buffer_head = block_buffer_tail = 0;
   memset(position, 0, sizeof(position)); // clear position
-  for (int i=0; i<NUM_AXIS; i++) previous_speed[i] = 0.0;
+  for (int i = 0; i < NUM_AXIS; i++) previous_speed[i] = 0.0;
   previous_nominal_speed = 0.0;
 }
 
@@ -374,7 +373,7 @@ void plan_init() {
     uint8_t block_index = block_buffer_tail;
 
     while (block_index != block_buffer_head) {
-      block_t *block = &block_buffer[block_index];
+      block_t* block = &block_buffer[block_index];
       if (block->steps[X_AXIS] || block->steps[Y_AXIS] || block->steps[Z_AXIS]) {
         float se = (float)block->steps[E_AXIS] / block->step_event_count * block->nominal_speed; // mm/sec;
         if (se > high) high = se;
@@ -391,7 +390,7 @@ void plan_init() {
     oldt = t;
     setTargetHotend0(t);
   }
-#endif
+#endif //AUTOTEMP
 
 void check_axes_activity() {
   unsigned char axis_active[NUM_AXIS] = { 0 },
@@ -401,7 +400,7 @@ void check_axes_activity() {
                   tail_e_to_p_pressure = EtoPPressure;
   #endif
 
-  block_t *block;
+  block_t* block;
 
   if (blocks_queued()) {
     uint8_t block_index = block_buffer_tail;
@@ -413,7 +412,7 @@ void check_axes_activity() {
     #endif
     while (block_index != block_buffer_head) {
       block = &block_buffer[block_index];
-      for (int i=0; i<NUM_AXIS; i++) if (block->steps[i]) axis_active[i]++;
+      for (int i = 0; i < NUM_AXIS; i++) if (block->steps[i]) axis_active[i]++;
       block_index = next_block_index(block_index);
     }
   }
@@ -461,10 +460,10 @@ void check_axes_activity() {
 
   #if ENABLED(BARICUDA)
     #if HAS_HEATER_1
-      analogWrite(HEATER_1_PIN,tail_valve_pressure);
+      analogWrite(HEATER_1_PIN, tail_valve_pressure);
     #endif
     #if HAS_HEATER_2
-      analogWrite(HEATER_2_PIN,tail_e_to_p_pressure);
+      analogWrite(HEATER_2_PIN, tail_e_to_p_pressure);
     #endif
   #endif
 }
@@ -475,9 +474,9 @@ float junction_deviation = 0.1;
 // mm. Microseconds specify how many microseconds the move should take to perform. To aid acceleration
 // calculation the caller must also provide the physical length of the line in millimeters.
 #if ENABLED(AUTO_BED_LEVELING_FEATURE) || ENABLED(MESH_BED_LEVELING)
-  void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, const uint8_t extruder)
+  void plan_buffer_line(float x, float y, float z, const float& e, float feed_rate, const uint8_t extruder)
 #else
-  void plan_buffer_line(const float &x, const float &y, const float &z, const float &e, float feed_rate, const uint8_t extruder)
+  void plan_buffer_line(const float& x, const float& y, const float& z, const float& e, float feed_rate, const uint8_t extruder)
 #endif  // AUTO_BED_LEVELING_FEATURE
 {
   // Calculate the buffer head after we push this byte
@@ -532,7 +531,7 @@ float junction_deviation = 0.1;
   #endif
 
   // Prepare to set up new block
-  block_t *block = &block_buffer[block_buffer_head];
+  block_t* block = &block_buffer[block_buffer_head];
 
   // Mark block as not busy (Not executed by the stepper interrupt)
   block->busy = false;
@@ -622,7 +621,7 @@ float junction_deviation = 0.1;
   if (block->steps[E_AXIS]) {
     if (DISABLE_INACTIVE_EXTRUDER) { //enable only selected extruder
 
-      for (int i=0; i<EXTRUDERS; i++)
+      for (int i = 0; i < EXTRUDERS; i++)
         if (g_uc_extruder_last_move[i] > 0) g_uc_extruder_last_move[i]--;
 
       switch(extruder) {
@@ -873,9 +872,9 @@ float junction_deviation = 0.1;
     // Compute path unit vector
     double unit_vec[3];
 
-    unit_vec[X_AXIS] = delta_mm[X_AXIS]*inverse_millimeters;
+    unit_vec[X_AXIS] = delta_mm[X_AXIS] * inverse_millimeters;
-    unit_vec[Y_AXIS] = delta_mm[Y_AXIS]*inverse_millimeters;
+    unit_vec[Y_AXIS] = delta_mm[Y_AXIS] * inverse_millimeters;
-    unit_vec[Z_AXIS] = delta_mm[Z_AXIS]*inverse_millimeters;
+    unit_vec[Z_AXIS] = delta_mm[Z_AXIS] * inverse_millimeters;
 
     // Compute maximum allowable entry speed at junction by centripetal acceleration approximation.
     // Let a circle be tangent to both previous and current path line segments, where the junction
@@ -893,18 +892,17 @@ float junction_deviation = 0.1;
       // Compute cosine of angle between previous and current path. (prev_unit_vec is negative)
       // NOTE: Max junction velocity is computed without sin() or acos() by trig half angle identity.
       double cos_theta = - previous_unit_vec[X_AXIS] * unit_vec[X_AXIS]
-        - previous_unit_vec[Y_AXIS] * unit_vec[Y_AXIS]
+                         - previous_unit_vec[Y_AXIS] * unit_vec[Y_AXIS]
-        - previous_unit_vec[Z_AXIS] * unit_vec[Z_AXIS] ;
+                         - previous_unit_vec[Z_AXIS] * unit_vec[Z_AXIS] ;
-
       // Skip and use default max junction speed for 0 degree acute junction.
       if (cos_theta < 0.95) {
-        vmax_junction = min(previous_nominal_speed,block->nominal_speed);
+        vmax_junction = min(previous_nominal_speed, block->nominal_speed);
         // Skip and avoid divide by zero for straight junctions at 180 degrees. Limit to min() of nominal speeds.
         if (cos_theta > -0.95) {
           // Compute maximum junction velocity based on maximum acceleration and junction deviation
-          double sin_theta_d2 = sqrt(0.5*(1.0-cos_theta)); // Trig half angle identity. Always positive.
+          double sin_theta_d2 = sqrt(0.5 * (1.0 - cos_theta)); // Trig half angle identity. Always positive.
           vmax_junction = min(vmax_junction,
-          sqrt(block->acceleration * junction_deviation * sin_theta_d2/(1.0-sin_theta_d2)) );
+                              sqrt(block->acceleration * junction_deviation * sin_theta_d2 / (1.0 - sin_theta_d2)));
         }
       }
     }
@@ -1008,9 +1006,9 @@ float junction_deviation = 0.1;
 #endif // AUTO_BED_LEVELING_FEATURE && !DELTA
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE) || ENABLED(MESH_BED_LEVELING)
-  void plan_set_position(float x, float y, float z, const float &e)
+  void plan_set_position(float x, float y, float z, const float& e)
 #else
-  void plan_set_position(const float &x, const float &y, const float &z, const float &e)
+  void plan_set_position(const float& x, const float& y, const float& z, const float& e)
 #endif // AUTO_BED_LEVELING_FEATURE || MESH_BED_LEVELING
   {
     #if ENABLED(MESH_BED_LEVELING)
@@ -1026,10 +1024,10 @@ float junction_deviation = 0.1;
     st_set_position(nx, ny, nz, ne);
     previous_nominal_speed = 0.0; // Resets planner junction speeds. Assumes start from rest.
 
-    for (int i=0; i<NUM_AXIS; i++) previous_speed[i] = 0.0;
+    for (int i = 0; i < NUM_AXIS; i++) previous_speed[i] = 0.0;
   }
 
-void plan_set_e_position(const float &e) {
+void plan_set_e_position(const float& e) {
   position[E_AXIS] = lround(e * axis_steps_per_unit[E_AXIS]);
   st_set_e_position(position[E_AXIS]);
 }

Marlin/planner.h

@@ -97,23 +97,23 @@ FORCE_INLINE uint8_t movesplanned() { return BLOCK_MOD(block_buffer_head - block
    * Add a new linear movement to the buffer. x, y, z are the signed, absolute target position in
    * millimeters. Feed rate specifies the (target) speed of the motion.
    */
-  void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, const uint8_t extruder);
+  void plan_buffer_line(float x, float y, float z, const float& e, float feed_rate, const uint8_t extruder);
 
   /**
    * Set the planner positions. Used for G92 instructions.
    * Multiplies by axis_steps_per_unit[] to set stepper positions.
    * Clears previous speed values.
    */
-  void plan_set_position(float x, float y, float z, const float &e);
+  void plan_set_position(float x, float y, float z, const float& e);
 
 #else
 
-  void plan_buffer_line(const float &x, const float &y, const float &z, const float &e, float feed_rate, const uint8_t extruder);
+  void plan_buffer_line(const float& x, const float& y, const float& z, const float& e, float feed_rate, const uint8_t extruder);
-  void plan_set_position(const float &x, const float &y, const float &z, const float &e);
+  void plan_set_position(const float& x, const float& y, const float& z, const float& e);
 
 #endif // AUTO_BED_LEVELING_FEATURE || MESH_BED_LEVELING
 
-void plan_set_e_position(const float &e);
+void plan_set_e_position(const float& e);
 
 //===========================================================================
 //============================= public variables ============================
@@ -155,9 +155,9 @@ FORCE_INLINE void plan_discard_current_block() {
 }
 
 // Gets the current block. Returns NULL if buffer empty
-FORCE_INLINE block_t *plan_get_current_block() {
+FORCE_INLINE block_t* plan_get_current_block() {
   if (blocks_queued()) {
-    block_t *block = &block_buffer[block_buffer_tail];
+    block_t* block = &block_buffer[block_buffer_tail];
     block->busy = true;
     return block;
   }