ed6598adf5
Corrected Bed Height vs. Bed Topology for verbosity > 3
...
and cleaned out some tabs.
Everything else is a rebased PR#2017 as proposed by @CptanPanic
2015-07-15 19:51:40 -05:00
62302ceb9e
Add calculation of difference between auto-correct bed level plane, and measured topo map.
2015-07-15 19:51:40 -05:00
49609f6c14
Activate the new servo.move() function
...
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
2015-07-15 17:39:43 -05:00
87a872e103
Use st_get_position_mm where possible (PR#2411)
2015-07-12 22:15:54 -05:00
2e0da8abdc
Allow N to take a negative argument (PR@2402)
2015-07-12 22:14:25 -05:00
447dbd6fa5
Add STEPPER_RESET_PIN support
2015-07-11 16:04:11 -05:00
6b1b8cb2b3
Also nullify spaces before the checksum asterisk (PR#2409)
2015-07-10 09:03:07 -05:00
4e9d658141
Prevent a hanging SERIAL_ECHO_START in M111
2015-07-07 06:59:10 -05:00
6b494c1535
Use disable_all_heaters in M111
2015-07-07 06:59:10 -05:00
15190d40df
Add extra EOL after M111
2015-07-07 06:59:10 -05:00
d421f5250d
Correct the sign of zprobe_zoffset for G29 (PR#@391)
...
Sign flipped with #2167 .
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
2015-07-07 06:55:33 -05:00
52fcc743ab
Replace "target" with "destination" in M600 (PR#2374)
...
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
2015-07-04 05:55:25 -05:00
23c8c5348f
Z-height fix V2b (PR#2351)
...
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
2015-07-02 20:30:40 -05:00
a111fbbd0a
z-probe offset fix (PR#2361)
...
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
2015-07-02 20:28:07 -05:00
9682ed455e
Fix comment on M83, add comment to prepare_move
2015-06-28 08:20:19 -05:00
36746143a1
Correct output of M48 (PR#2336)
...
n_samples is an uint8_t .
Got printouts like:
50 of 2 ...
2015-06-27 06:08:40 -05:00
f6ca5a8da8
Allow "M110 N123" without a checksum
2015-06-26 18:13:54 -05:00
aaad65ff5d
Include a comment documenting M110
2015-06-26 18:13:54 -05:00
862c72b030
Put the mandatory test of gcode_N first
2015-06-26 18:13:54 -05:00
30976f9773
Allow M110 to handle a second N argument
2015-06-26 18:13:53 -05:00
5ccb1c9e7d
Use millis for M600 audio feedback interval
2015-06-25 20:45:03 -05:00
fb16a83b8a
Cleanup M600 documentation comments
2015-06-25 20:45:03 -05:00
97ec224d72
Replace target with destination in M600
2015-06-25 20:45:03 -05:00
4ce9ddbb74
Check the temperature before filament change
2015-06-25 20:45:03 -05:00
722829b058
Move buzzing code to buzzr.h & buzzer.cpp (PR#2307)
...
at least the lcd independent part from Marlin_main.cpp.
2015-06-22 22:31:48 -04:00
1e9cf905c7
Enable ZigZag AutoBedLeveling on Deltas (PR#2273)
...
ZigZag has been disabled by fault due to do_topography_map
2015-06-15 20:26:25 -05:00
6ab7b560af
Rework buzzing (PR#2296)
...
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.
Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.
All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.
To do: Check the conditions for the BEEPER-pin in all pin-files.
2015-06-15 06:13:26 -05:00
29122db2fa
Fix ULTRA_LCD spelling in HAS_LCD_BUZZ
2015-06-15 06:12:34 -05:00
e2a4a83586
Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281 )
2015-06-12 22:39:35 -05:00
eb81982fcd
Fix error next command in autotune (PR#2274)
...
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
2015-06-12 07:10:38 -05:00
55b23c896a
Optimise out_of_range_error() (PR#2265)
...
by avoiding the strncopy()
2015-06-12 02:20:40 -05:00
45642b7fe8
Respect DISABLE_AXIS settings (PR#2216)
...
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
2015-06-11 11:35:05 -05:00
962b107341
Prevent current_command_args from bypassing nul (PR#2270)
2015-06-09 16:07:10 -05:00
ff6081be3a
Parse N[0-9]+[ ]* differently (PR #2263 )
...
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
2015-06-08 17:06:49 -05:00
96a3fba8ac
Reverse the sign of zprobe_zoffset
...
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
2015-06-08 05:09:27 -05:00
8d295547be
* Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button.
2015-06-06 19:45:45 -05:00
ad09d6a60f
3 Step Allen Key Probe
2015-06-06 17:48:27 -05:00
e400fce271
Merge pull request #2221 from MagoKimbra/Dryrun
...
Insert Debug DRYRUN Repetier Host compatible
2015-06-03 12:30:48 +02:00
c3fe6e61ae
Merge pull request #2229 from AnHardt/position-out-of-range
...
Fix out_of_range_error()
2015-06-03 09:46:22 +02:00
d1f4471000
Merge pull request #2146 from Wackerbarth/Versioning
...
Versioning
2015-06-02 18:31:21 +02:00
17b0ec84ed
Fix out_of_range_error()
...
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
2015-06-02 11:50:32 +02:00
35af5ef23e
Merge pull request #2225 from Wurstnase/naming
...
consistency name for multiplier
2015-06-02 10:18:22 +02:00
e7e964432b
consistency name for multiplier
...
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
2015-06-01 22:33:22 +02:00
76306f9073
Insert Debug DRYRUN Repetier Host compatible
2015-06-01 18:34:45 +02:00
881146bc22
Fix problem Width Cura
2015-06-01 17:25:32 +02:00
9d2a980bcf
Merge pull request #2170 from thinkyhead/beep_M600_elsewise
...
Slight size reduction by adding idle()
2015-05-30 12:42:32 +02:00
2728dc0606
Merge pull request #2194 from thinkyhead/reduce_strings
...
Redo "invalid extruder" to save 304 bytes
2015-05-30 11:05:08 +02:00
be5236e839
Reduce setTargetedHotend by removing the switch
2015-05-29 18:03:58 -07:00
06f401e7e5
Redo "invalid extruder" to save 264 bytes
...
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
2015-05-28 22:25:28 -07:00
1a882bcc2e
Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands
...
Ignore unknown commands if they start with G, M, or T
2015-05-28 22:03:48 -07:00
