228 lines
5.8 KiB
C
228 lines
5.8 KiB
C
/**
|
|
* Arduino Mega with RAMPS v1.3 pin assignments
|
|
*
|
|
* Applies to the following boards:
|
|
*
|
|
* RAMPS_13_EFB (Extruder, Fan, Bed)
|
|
* RAMPS_13_EEB (Extruder, Extruder, Bed)
|
|
* RAMPS_13_EFF (Extruder, Fan, Fan)
|
|
* RAMPS_13_EEF (Extruder, Extruder, Fan)
|
|
* 3DRAG
|
|
* K8200
|
|
* AZTEEG_X3
|
|
* AZTEEG_X3_PRO
|
|
*/
|
|
|
|
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
|
|
#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
#define LARGE_FLASH true
|
|
|
|
#define X_STEP_PIN 54
|
|
#define X_DIR_PIN 55
|
|
#define X_ENABLE_PIN 38
|
|
#define X_MIN_PIN 3
|
|
#define X_MAX_PIN 2
|
|
|
|
#define Y_STEP_PIN 60
|
|
#define Y_DIR_PIN 61
|
|
#define Y_ENABLE_PIN 56
|
|
#define Y_MIN_PIN 14
|
|
#define Y_MAX_PIN 15
|
|
|
|
#define Z_STEP_PIN 46
|
|
#define Z_DIR_PIN 48
|
|
#define Z_ENABLE_PIN 62
|
|
#define Z_MIN_PIN 18
|
|
#define Z_MAX_PIN 19
|
|
|
|
#define Y2_STEP_PIN 36
|
|
#define Y2_DIR_PIN 34
|
|
#define Y2_ENABLE_PIN 30
|
|
|
|
#define Z2_STEP_PIN 36
|
|
#define Z2_DIR_PIN 34
|
|
#define Z2_ENABLE_PIN 30
|
|
|
|
#define E0_STEP_PIN 26
|
|
#define E0_DIR_PIN 28
|
|
#define E0_ENABLE_PIN 24
|
|
|
|
#define E1_STEP_PIN 36
|
|
#define E1_DIR_PIN 34
|
|
#define E1_ENABLE_PIN 30
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS 53
|
|
#define LED_PIN 13
|
|
|
|
#if MB(RAMPS_13_EEB) && defined(FILAMENT_SENSOR) // FMM added for Filament Extruder
|
|
// define analog pin for the filament width sensor input
|
|
// Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
|
|
#define FILWIDTH_PIN 5
|
|
#endif
|
|
|
|
#if MB(RAMPS_13_EFB) || MB(RAMPS_13_EFF) || MB(AZTEEG_X3) || MB(AZTEEG_X3_PRO) || MB(WITBOX) || MB(HEPHESTOS)
|
|
#define FAN_PIN 9 // (Sprinter config)
|
|
#if MB(RAMPS_13_EFF)
|
|
#define CONTROLLERFAN_PIN -1 // Pin used for the fan to cool controller
|
|
#endif
|
|
#elif MB(RAMPS_13_EEF)
|
|
#define FAN_PIN 8
|
|
#else
|
|
#define FAN_PIN 4 // IO pin. Buffer needed
|
|
#endif
|
|
|
|
#define PS_ON_PIN 12
|
|
|
|
#if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
|
|
#define KILL_PIN 41
|
|
#else
|
|
#define KILL_PIN -1
|
|
#endif
|
|
|
|
#if MB(RAMPS_13_EFF)
|
|
#define HEATER_0_PIN 8
|
|
#else
|
|
#define HEATER_0_PIN 10 // EXTRUDER 1
|
|
#endif
|
|
|
|
#if MB(RAMPS_13_EFB) || MB(AZTEEG_X3) || MB(WITBOX) || MB(HEPHESTOS)
|
|
#define HEATER_1_PIN -1
|
|
#else
|
|
#define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter)
|
|
#endif
|
|
|
|
#define HEATER_2_PIN -1
|
|
|
|
#define TEMP_0_PIN 13 // ANALOG NUMBERING
|
|
#define TEMP_1_PIN 15 // ANALOG NUMBERING
|
|
#define TEMP_2_PIN -1 // ANALOG NUMBERING
|
|
|
|
#if MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF)
|
|
#define HEATER_BED_PIN -1 // NO BED
|
|
#else
|
|
#define HEATER_BED_PIN 8 // BED
|
|
#endif
|
|
|
|
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
|
|
|
|
#ifdef NUM_SERVOS
|
|
#define SERVO0_PIN 11
|
|
|
|
#if NUM_SERVOS > 1
|
|
#define SERVO1_PIN 6
|
|
#endif
|
|
|
|
#if NUM_SERVOS > 2
|
|
#define SERVO2_PIN 5
|
|
#endif
|
|
|
|
#if NUM_SERVOS > 3
|
|
#define SERVO3_PIN 4
|
|
#endif
|
|
#endif
|
|
|
|
#if MB(AZTEEG_X3_PRO)
|
|
#define BEEPER 33
|
|
#endif
|
|
|
|
#ifdef TEMP_STAT_LEDS
|
|
#if MB(AZTEEG_X3)
|
|
#define STAT_LED_RED 6
|
|
#define STAT_LED_BLUE 11
|
|
#endif
|
|
#endif
|
|
|
|
#ifdef ULTRA_LCD
|
|
|
|
#ifdef NEWPANEL
|
|
#define LCD_PINS_RS 16
|
|
#define LCD_PINS_ENABLE 17
|
|
#define LCD_PINS_D4 23
|
|
#define LCD_PINS_D5 25
|
|
#define LCD_PINS_D6 27
|
|
#define LCD_PINS_D7 29
|
|
|
|
#ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
|
|
#define BEEPER 37
|
|
|
|
#define BTN_EN1 31
|
|
#define BTN_EN2 33
|
|
#define BTN_ENC 35
|
|
|
|
#define SDCARDDETECT 49
|
|
#elif defined(LCD_I2C_PANELOLU2)
|
|
#define BTN_EN1 47 // reverse if the encoder turns the wrong way.
|
|
#define BTN_EN2 43
|
|
#define BTN_ENC 32
|
|
#define LCD_SDSS 53
|
|
#define SDCARDDETECT -1
|
|
#define KILL_PIN 41
|
|
#elif defined(LCD_I2C_VIKI)
|
|
#define BTN_EN1 22 // reverse if the encoder turns the wrong way.
|
|
#define BTN_EN2 7
|
|
#define BTN_ENC -1
|
|
#define LCD_SDSS 53
|
|
#define SDCARDDETECT 49
|
|
#else
|
|
// arduino pin which triggers an piezzo beeper
|
|
#define BEEPER 33 // Beeper on AUX-4
|
|
|
|
// buttons are directly attached using AUX-2
|
|
#ifdef REPRAPWORLD_KEYPAD
|
|
#define BTN_EN1 64 // encoder
|
|
#define BTN_EN2 59 // encoder
|
|
#define BTN_ENC 63 // enter button
|
|
#define SHIFT_OUT 40 // shift register
|
|
#define SHIFT_CLK 44 // shift register
|
|
#define SHIFT_LD 42 // shift register
|
|
#else
|
|
#define BTN_EN1 37
|
|
#define BTN_EN2 35
|
|
#define BTN_ENC 31 // the click
|
|
#endif
|
|
|
|
#ifdef G3D_PANEL
|
|
#define SDCARDDETECT 49
|
|
#else
|
|
#define SDCARDDETECT -1 // Ramps does not use this port
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#else // Old-style panel with shift register
|
|
// Arduino pin witch triggers an piezzo beeper
|
|
#define BEEPER 33 // No Beeper added
|
|
|
|
// Buttons are attached to a shift register
|
|
// Not wired yet
|
|
// #define SHIFT_CLK 38
|
|
// #define SHIFT_LD 42
|
|
// #define SHIFT_OUT 40
|
|
// #define SHIFT_EN 17
|
|
|
|
#define LCD_PINS_RS 16
|
|
#define LCD_PINS_ENABLE 17
|
|
#define LCD_PINS_D4 23
|
|
#define LCD_PINS_D5 25
|
|
#define LCD_PINS_D6 27
|
|
#define LCD_PINS_D7 29
|
|
#endif
|
|
#endif // ULTRA_LCD
|
|
|
|
// SPI for Max6675 Thermocouple
|
|
#ifndef SDSUPPORT
|
|
#define MAX6675_SS 66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card
|
|
#else
|
|
#define MAX6675_SS 66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
|
|
#endif
|
|
|
|
#ifndef SDSUPPORT
|
|
// these pins are defined in the SD library if building with SD support
|
|
#define SCK_PIN 52
|
|
#define MISO_PIN 50
|
|
#define MOSI_PIN 51
|
|
#endif
|