- Factoring of auto.c

- Implementation of fallback/normal support for the amd solo board
- Minor bugfix in romcc


git-svn-id: svn://svn.coreboot.org/coreboot/trunk@867 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

src/southbridge/amd/amd8111/amd8111_early_smbus.c

@@ -0,0 +1,108 @@
+#define SMBUS_IO_BASE 0x1000
+
+#define SMBGSTATUS 0xe0
+#define SMBGCTL    0xe2
+#define SMBHSTADDR 0xe4
+#define SMBHSTDAT  0xe6
+#define SMBHSTCMD  0xe8
+#define SMBHSTFIFO 0xe9
+
+#define SMBUS_TIMEOUT (100*1000*10)
+
+static void enable_smbus(void)
+{
+	uint32_t addr;
+	addr = pci_locate_device(PCI_ID(0x1022, 0x746b), 0);
+	if (addr == ~0U) {
+		die("SMBUS controller not found\r\n");
+	}
+	uint8_t enable;
+	print_debug("SMBus controller enabled\r\n");
+	pci_write_config32(addr + 0x58, SMBUS_IO_BASE | 1);
+	enable = pci_read_config8(addr + 0x41);
+	pci_write_config8(addr + 0x41, enable | (1 << 7));
+}
+
+
+static inline void smbus_delay(void)
+{
+	outb(0x80, 0x80);
+}
+
+static int smbus_wait_until_ready(void)
+{
+	unsigned long loops;
+	loops = SMBUS_TIMEOUT;
+	do {
+		unsigned short val;
+		smbus_delay();
+		val = inw(SMBUS_IO_BASE + SMBGSTATUS);
+		if ((val & 0x800) == 0) {
+			break;
+		}
+	} while(--loops);
+	return loops?0:-1;
+}
+
+static int smbus_wait_until_done(void)
+{
+	unsigned long loops;
+	loops = SMBUS_TIMEOUT;
+	do {
+		unsigned short val;
+		smbus_delay();
+		
+		val = inw(SMBUS_IO_BASE + SMBGSTATUS);
+		if (((val & 0x8) == 0) || ((val & 0x437) != 0)) {
+			break;
+		}
+	} while(--loops);
+	return loops?0:-1;
+}
+
+static int smbus_read_byte(unsigned device, unsigned address)
+{
+	unsigned char global_control_register;
+	unsigned char global_status_register;
+	unsigned char byte;
+
+	if (smbus_wait_until_ready() < 0) {
+		return -1;
+	}
+	
+	/* setup transaction */
+	/* disable interrupts */
+	outw(inw(SMBUS_IO_BASE + SMBGCTL) & ~((1<<10)|(1<<9)|(1<<8)|(1<<4)), SMBUS_IO_BASE + SMBGCTL);
+	/* set the device I'm talking too */
+	outw(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBHSTADDR);
+	/* set the command/address... */
+	outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
+	/* set up for a byte data read */
+	outw((inw(SMBUS_IO_BASE + SMBGCTL) & ~7) | (0x2), SMBUS_IO_BASE + SMBGCTL);
+
+	/* clear any lingering errors, so the transaction will run */
+	/* Do I need to write the bits to a 1 to clear an error? */
+	outw(inw(SMBUS_IO_BASE + SMBGSTATUS), SMBUS_IO_BASE + SMBGSTATUS);
+
+	/* clear the data word...*/
+	outw(0, SMBUS_IO_BASE + SMBHSTDAT);
+
+	/* start the command */
+	outw((inw(SMBUS_IO_BASE + SMBGCTL) | (1 << 3)), SMBUS_IO_BASE + SMBGCTL);
+
+
+	/* poll for transaction completion */
+	if (smbus_wait_until_done() < 0) {
+		return -1;
+	}
+
+	global_status_register = inw(SMBUS_IO_BASE + SMBGSTATUS);
+
+	/* read results of transaction */
+	byte = inw(SMBUS_IO_BASE + SMBHSTDAT) & 0xff;
+
+	if (global_status_register != (1 << 4)) {
+		return -1;
+	}
+	return byte;
+}

src/southbridge/amd/amd8111/amd8111_enable_rom.c

@@ -0,0 +1,18 @@
+
+static void amd8111_enable_rom(void)
+{
+	unsigned char byte;
+	uint32_t addr;
+
+	/* Enable 4MB rom access at 0xFFC00000 - 0xFFFFFFFF */
+	/* Locate the amd8111 */
+	addr = pci_locate_device(PCI_ID(0x1022, 0x7468), 0);
+	
+	/* Refine the address to point at the rom enable byte */
+	addr += 0x43;
+
+	/* Set the 4MB enable bit bit */
+	byte = pci_read_config8(addr);
+	byte |= 0x80;
+	pci_write_config8(addr, byte);
+}