adapt to 1.1.6

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1445 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

src/mainboard/newisys/khepri/Config.lb

@@ -1,28 +1,34 @@
 uses HAVE_MP_TABLE
 uses HAVE_PIRQ_TABLE
 uses USE_FALLBACK_IMAGE
-uses USE_OPTION_TABLE
 uses HAVE_FALLBACK_BOOT
 uses HAVE_HARD_RESET
+uses IRQ_SLOT_COUNT
 uses HAVE_OPTION_TABLE
+uses CONFIG_MAX_CPUS
+uses CONFIG_IOAPIC
+uses CONFIG_SMP
 uses FALLBACK_SIZE
 uses ROM_SIZE
 uses ROM_SECTION_SIZE
 uses ROM_IMAGE_SIZE
 uses ROM_SECTION_SIZE
 uses ROM_SECTION_OFFSET
-uses CONFIG_SMP
-uses CONFIG_MAX_CPUS
-uses CONFIG_IOAPIC
 uses CONFIG_ROM_STREAM
 uses CONFIG_ROM_STREAM_START
 uses PAYLOAD_SIZE
 uses _ROMBASE
 uses XIP_ROM_SIZE
 uses XIP_ROM_BASE
-uses IRQ_SLOT_COUNT
 uses STACK_SIZE
 uses HEAP_SIZE
+uses USE_OPTION_TABLE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD_PART_NUMBER
+uses MAINBOARD_VENDOR
+
 
 ## ROM_SIZE is the size of boot ROM that this board will use.
 default ROM_SIZE=524288
@@ -45,7 +51,7 @@ default HAVE_HARD_RESET=1
 ## Build code to export a programmable irq routing table
 ##
 default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=7
+default IRQ_SLOT_COUNT=9
 
 ##
 ## Build code to export an x86 MP table
@@ -58,6 +64,13 @@ default HAVE_MP_TABLE=1
 ##
 default HAVE_OPTION_TABLE=1
 
+##
+## Move the default LinuxBIOS cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
 ##
 ## Build code for SMP support
 ## Only worry about 2 micro processors
@@ -70,6 +83,12 @@ default CONFIG_MAX_CPUS=2
 ##
 default CONFIG_IOAPIC=1
 
+##
+## Clean up the motherboard id strings
+##
+default MAINBOARD_PART_NUMBER="Khepri 2100"
+default MAINBOARD_VENDOR="Newisys"
+
 ###
 ### LinuxBIOS layout values
 ###
@@ -154,12 +173,12 @@ end
 
 makerule ./failover.inc
 	depends "./failover.E ./romcc"
-	action "./romcc -O2 -o failover.inc --label-prefix=failover ./failover.E"
+	action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"
 end
 
 makerule ./auto.E 
-	depends	"$(MAINBOARD)/auto.c" 
+	depends	"$(MAINBOARD)/auto.c option_table.h"
-	action	"$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
+	action	"$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
 end
 makerule ./auto.inc 
 	depends "./auto.E ./romcc"
@@ -171,6 +190,7 @@ end
 ##
 mainboardinit cpu/i386/entry16.inc
 mainboardinit cpu/i386/entry32.inc
+mainboardinit cpu/i386/bist32.inc
 ldscript /cpu/i386/entry16.lds
 ldscript /cpu/i386/entry32.lds
 
@@ -300,4 +320,5 @@ end
 ##
 mainboardinit pc80/serial.inc
 mainboardinit arch/i386/lib/console.inc
+mainboardinit cpu/i386/bist32_fail.inc
 

src/mainboard/newisys/khepri/auto.c

@@ -4,9 +4,8 @@
 
 #include <stdint.h>
 #include <device/pci_def.h>
-#include <cpu/p6/apic.h>
 #include <arch/io.h>
-#include <device/pnp.h>
+#include <device/pnp_def.h>
 #include <arch/romcc_io.h>
 #include <arch/smp/lapic.h>
 #include "option_table.h"
@@ -98,13 +97,13 @@ static unsigned int generate_row(uint8_t node, uint8_t row, uint8_t maxnodes)
 		{ 0x00010404, 0x00050101 }
 	};
 
-	if(maxnodes>2) {
+	if(maxnodes > 2) {
 		print_debug("this mainboard is only designed for 2 cpus\r\n");
 		maxnodes=2;
 	}
 
 
-	if (!(node>=maxnodes || row>=maxnodes)) {
+	if (!(node >= maxnodes || row >= maxnodes)) {
 		ret=rows_2p[node][row];
 	}
 
@@ -176,7 +175,6 @@ static void main(void)
 		print_info("ht reset -");
 		soft_reset();
 	}
-	
 #if 0
 	print_pci_devices();
 #endif
@@ -194,7 +192,6 @@ static void main(void)
 	dump_pci_device(PCI_DEV(0, 0x18, 2));
 #endif
 
-	/* Check all of memory */
 #if 0
 	/* Check the first 1M */
 	ram_check(0x00000000, 0x000100000);

src/mainboard/newisys/khepri/cmos.layout

@@ -29,6 +29,9 @@ entries
 386          1       e       1        ECC_memory
 388          4       r       0        reboot_bits
 392          3       e       5        baud_rate
+395          1       e       1        hw_scrubber
+396          1       e       1        interleave_chip_selects
+397          2       e       8        max_mem_clock
 400          1       e       1        power_on_after_fail
 412          4       e       6        debug_level
 416          4       e       7        boot_first
@@ -36,7 +39,14 @@ entries
 424          4       e       7        boot_third
 428          4       h       0        boot_index
 432	     8       h       0        boot_countdown
-1008         16      h       0        check_sum
+440          4       e       9        slow_cpu
+444          1       e       1        nmi
+728        256       h       0        user_data
+984         16       h       0        check_sum
+# Reserve the extended AMD configuration registers
+1000        24       r       0        reserved_memory
+
+
 
 enumerations
 
@@ -66,9 +76,21 @@ enumerations
 7     9     Fallback_HDD
 7     10    Fallback_Floppy
 #7     3     ROM
+8     0     200Mhz
+8     1     166Mhz
+8     2     133Mhz
+8     3     100Mhz
+9     0     off
+9     1     87.5%
+9     2     75.0%
+9     3     62.5%
+9     4     50.0%
+9     5     37.5%
+9     6     25.0%
+9     7     12.5%
 
 checksums
 
-checksum 392 1007 1008
+checksum 392 983 984
 
 

src/mainboard/newisys/khepri/failover.c

@@ -14,7 +14,7 @@ static void main(void)
 {
 	/* Nothing special needs to be done to find bus 0 */
 	/* Allow the HT devices to be found */
-	enumerate_ht_chain(0);
+	enumerate_ht_chain();
 
 	/* Setup the 8111 */
 	amd8111_enable_rom();