- Small step forward Linux boots and almost works...

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@795 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2003-04-24 06:25:08 +00:00
parent 8ca8d7665d
commit 5899fd82aa
17 changed files with 3024 additions and 22 deletions
--- a/src/include/device/device.h
+++ b/src/include/device/device.h
@@ -0,0 +1,91 @@
+#ifndef DEVICE_H
+#define DEVICE_H
+
+#include <device/resource.h>
+
+struct device;
+struct device_operations {
+	void (*read_resources)(struct device *dev);
+	void (*set_resources)(struct device *dev);
+	void (*init)(struct device *dev);
+	unsigned int (*scan_bus)(struct device *bus, unsigned int max);
+};
+
+
+#define MAX_RESOURCES 6
+/*
+ * There is one pci_dev structure for each slot-number/function-number
+ * combination:
+ */
+
+struct device {
+	struct device	*bus;		/* bus this device is on */
+	struct device	*children;	/* devices behind this bridge */
+	struct device	*sibling;	/* next device on this bus */
+	struct device	*next;		/* chain of all devices */
+
+	unsigned int	devfn;		/* encoded device & function index */
+	unsigned short	vendor;
+	unsigned short	device;
+	unsigned int	class;		/* 3 bytes: (base,sub,prog-if) */
+	unsigned int	hdr_type;	/* PCI header type */
+	unsigned int	master : 1;	/* set if device is master capable */
+
+	unsigned char	secondary; 	/* secondary bus number */
+	unsigned char	subordinate;	/* max subordinate bus number */
+	uint8_t command;
+	/*
+	 * In theory, the irq level can be read from configuration
+	 * space and all would be fine.  However, old PCI chips don't
+	 * support these registers and return 0 instead.  For example,
+	 * the Vision864-P rev 0 chip can uses INTA, but returns 0 in
+	 * the interrupt line and pin registers.  pci_init()
+	 * initializes this field with the value at PCI_INTERRUPT_LINE
+	 * and it is the job of pcibios_fixup() to change it if
+	 * necessary.  The field must not be 0 unless the device
+	 * cannot generate interrupts at all.
+	 */
+	unsigned int	irq;		/* irq generated by this device */
+
+	/* Base registers for this device, can be adjusted by
+	 * pcibios_fixup() as necessary.
+	 */
+	struct resource resource[MAX_RESOURCES];
+	unsigned int resources;
+	unsigned long rom_address;
+	struct device_operations *ops;
+
+};
+
+extern struct device	dev_root;	/* root bus */
+extern struct device	*all_devices;	/* list of all devices */
+
+
+/* Generic device interface functions */
+extern void dev_enumerate(void);
+extern void dev_configure(void);
+extern void dev_enable(void);
+extern void dev_initialize(void);
+
+/* Generic device helper functions */
+void append_device(struct device *dev);
+void compute_allocate_resource(struct device *bus, struct resource *bridge,
+	unsigned long type_mask, unsigned long type);
+void assign_resources(struct device *bus);
+void enumerate_static_device(void);
+unsigned long device_memory_base;
+
+
+/* Helper functions */
+struct device *dev_find_device (unsigned int vendor, unsigned int device, struct device *from);
+struct device *dev_find_class (unsigned int class, struct device *from);
+struct device *dev_find_slot (unsigned int bus, unsigned int devfn);
+
+/* Rounding for boundaries. 
+ * Due to some chip bugs, go ahead and roung IO to 16
+ */
+#define DEVICE_IO_ALIGN 16 
+#define DEVICE_MEM_ALIGN 4096
+
+
+#endif /* DEVICE_H */
--- a/src/include/device/pci.h
+++ b/src/include/device/pci.h
@@ -0,0 +1,310 @@
+/*
+ *	$Id$
+ *
+ *	PCI defines and function prototypes
+ *	Copyright 1994, Drew Eckhardt
+ *	Copyright 1997--1999 Martin Mares <mj@atrey.karlin.mff.cuni.cz>
+ *
+ *	For more information, please consult the following manuals (look at
+ *	http://www.pcisig.com/ for how to get them):
+ *
+ *	PCI BIOS Specification
+ *	PCI Local Bus Specification
+ *	PCI to PCI Bridge Specification
+ *	PCI System Design Guide
+ */
+
+#ifndef PCI_H
+#define PCI_H
+
+/*
+ * Under PCI, each device has 256 bytes of configuration address space,
+ * of which the first 64 bytes are standardized as follows:
+ */
+#define PCI_VENDOR_ID		0x00	/* 16 bits */
+#define PCI_DEVICE_ID		0x02	/* 16 bits */
+#define PCI_COMMAND		0x04	/* 16 bits */
+#define  PCI_COMMAND_IO		0x1	/* Enable response in I/O space */
+#define  PCI_COMMAND_MEMORY	0x2	/* Enable response in Memory space */
+#define  PCI_COMMAND_MASTER	0x4	/* Enable bus mastering */
+#define  PCI_COMMAND_SPECIAL	0x8	/* Enable response to special cycles */
+#define  PCI_COMMAND_INVALIDATE	0x10	/* Use memory write and invalidate */
+#define  PCI_COMMAND_VGA_PALETTE 0x20	/* Enable palette snooping */
+#define  PCI_COMMAND_PARITY	0x40	/* Enable parity checking */
+#define  PCI_COMMAND_WAIT 	0x80	/* Enable address/data stepping */
+#define  PCI_COMMAND_SERR	0x100	/* Enable SERR */
+#define  PCI_COMMAND_FAST_BACK	0x200	/* Enable back-to-back writes */
+
+#define PCI_STATUS		0x06	/* 16 bits */
+#define  PCI_STATUS_CAP_LIST	0x10	/* Support Capability List */
+#define  PCI_STATUS_66MHZ	0x20	/* Support 66 Mhz PCI 2.1 bus */
+#define  PCI_STATUS_UDF		0x40	/* Support User Definable Features [obsolete] */
+#define  PCI_STATUS_FAST_BACK	0x80	/* Accept fast-back to back */
+#define  PCI_STATUS_PARITY	0x100	/* Detected parity error */
+#define  PCI_STATUS_DEVSEL_MASK	0x600	/* DEVSEL timing */
+#define  PCI_STATUS_DEVSEL_FAST	0x000	
+#define  PCI_STATUS_DEVSEL_MEDIUM 0x200
+#define  PCI_STATUS_DEVSEL_SLOW 0x400
+#define  PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */
+#define  PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */
+#define  PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */
+#define  PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */
+#define  PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */
+
+#define PCI_CLASS_REVISION	0x08	/* High 24 bits are class, low 8
+					   revision */
+#define PCI_REVISION_ID         0x08    /* Revision ID */
+#define PCI_CLASS_PROG          0x09    /* Reg. Level Programming Interface */
+#define PCI_CLASS_DEVICE        0x0a    /* Device class */
+
+#define PCI_CACHE_LINE_SIZE	0x0c	/* 8 bits */
+#define PCI_LATENCY_TIMER	0x0d	/* 8 bits */
+#define PCI_HEADER_TYPE		0x0e	/* 8 bits */
+#define  PCI_HEADER_TYPE_NORMAL	0
+#define  PCI_HEADER_TYPE_BRIDGE 1
+#define  PCI_HEADER_TYPE_CARDBUS 2
+
+#define PCI_BIST		0x0f	/* 8 bits */
+#define PCI_BIST_CODE_MASK	0x0f	/* Return result */
+#define PCI_BIST_START		0x40	/* 1 to start BIST, 2 secs or less */
+#define PCI_BIST_CAPABLE	0x80	/* 1 if BIST capable */
+
+/*
+ * Base addresses specify locations in memory or I/O space.
+ * Decoded size can be determined by writing a value of 
+ * 0xffffffff to the register, and reading it back.  Only 
+ * 1 bits are decoded.
+ */
+#define PCI_BASE_ADDRESS_0	0x10	/* 32 bits */
+#define PCI_BASE_ADDRESS_1	0x14	/* 32 bits [htype 0,1 only] */
+#define PCI_BASE_ADDRESS_2	0x18	/* 32 bits [htype 0 only] */
+#define PCI_BASE_ADDRESS_3	0x1c	/* 32 bits */
+#define PCI_BASE_ADDRESS_4	0x20	/* 32 bits */
+#define PCI_BASE_ADDRESS_5	0x24	/* 32 bits */
+#define  PCI_BASE_ADDRESS_SPACE	0x01	/* 0 = memory, 1 = I/O */
+#define  PCI_BASE_ADDRESS_SPACE_IO 0x01
+#define  PCI_BASE_ADDRESS_SPACE_MEMORY 0x00
+#define  PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06
+#define  PCI_BASE_ADDRESS_MEM_TYPE_32	0x00	/* 32 bit address */
+#define  PCI_BASE_ADDRESS_MEM_TYPE_1M	0x02	/* Below 1M [obsolete] */
+#define  PCI_BASE_ADDRESS_MEM_TYPE_64	0x04	/* 64 bit address */
+#define  PCI_BASE_ADDRESS_MEM_PREFETCH	0x08	/* prefetchable? */
+#define  PCI_BASE_ADDRESS_MEM_MASK	(~0x0fUL)
+#define  PCI_BASE_ADDRESS_IO_MASK	(~0x03UL)
+/* bit 1 is reserved if address_space = 1 */
+
+/* Header type 0 (normal devices) */
+#define PCI_CARDBUS_CIS		0x28
+#define PCI_SUBSYSTEM_VENDOR_ID	0x2c
+#define PCI_SUBSYSTEM_ID	0x2e  
+#define PCI_ROM_ADDRESS		0x30	/* Bits 31..11 are address, 10..1 reserved */
+#define  PCI_ROM_ADDRESS_ENABLE	0x01
+#define PCI_ROM_ADDRESS_MASK	(~0x7ffUL)
+
+#define PCI_CAPABILITY_LIST	0x34	/* Offset of first capability list entry */
+
+/* 0x35-0x3b are reserved */
+#define PCI_INTERRUPT_LINE	0x3c	/* 8 bits */
+#define PCI_INTERRUPT_PIN	0x3d	/* 8 bits */
+#define PCI_MIN_GNT		0x3e	/* 8 bits */
+#define PCI_MAX_LAT		0x3f	/* 8 bits */
+
+/* Header type 1 (PCI-to-PCI bridges) */
+#define PCI_PRIMARY_BUS		0x18	/* Primary bus number */
+#define PCI_SECONDARY_BUS	0x19	/* Secondary bus number */
+#define PCI_SUBORDINATE_BUS	0x1a	/* Highest bus number behind the bridge */
+#define PCI_SEC_LATENCY_TIMER	0x1b	/* Latency timer for secondary interface */
+#define PCI_IO_BASE		0x1c	/* I/O range behind the bridge */
+#define PCI_IO_LIMIT		0x1d
+#define  PCI_IO_RANGE_TYPE_MASK	0x0f	/* I/O bridging type */
+#define  PCI_IO_RANGE_TYPE_16	0x00
+#define  PCI_IO_RANGE_TYPE_32	0x01
+#define  PCI_IO_RANGE_MASK	~0x0f
+#define PCI_SEC_STATUS		0x1e	/* Secondary status register, only bit 14 used */
+#define PCI_MEMORY_BASE		0x20	/* Memory range behind */
+#define PCI_MEMORY_LIMIT	0x22
+#define  PCI_MEMORY_RANGE_TYPE_MASK 0x0f
+#define  PCI_MEMORY_RANGE_MASK	~0x0f
+#define PCI_PREF_MEMORY_BASE	0x24	/* Prefetchable memory range behind */
+#define PCI_PREF_MEMORY_LIMIT	0x26
+#define  PCI_PREF_RANGE_TYPE_MASK 0x0f
+#define  PCI_PREF_RANGE_TYPE_32	0x00
+#define  PCI_PREF_RANGE_TYPE_64	0x01
+#define  PCI_PREF_RANGE_MASK	~0x0f
+#define PCI_PREF_BASE_UPPER32	0x28	/* Upper half of prefetchable memory range */
+#define PCI_PREF_LIMIT_UPPER32	0x2c
+#define PCI_IO_BASE_UPPER16	0x30	/* Upper half of I/O addresses */
+#define PCI_IO_LIMIT_UPPER16	0x32
+/* 0x34 same as for htype 0 */
+/* 0x35-0x3b is reserved */
+#define PCI_ROM_ADDRESS1	0x38	/* Same as PCI_ROM_ADDRESS, but for htype 1 */
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_BRIDGE_CONTROL	0x3e
+#define  PCI_BRIDGE_CTL_PARITY	0x01	/* Enable parity detection on secondary interface */
+#define  PCI_BRIDGE_CTL_SERR	0x02	/* The same for SERR forwarding */
+#define  PCI_BRIDGE_CTL_NO_ISA	0x04	/* Disable bridging of ISA ports */
+#define  PCI_BRIDGE_CTL_VGA	0x08	/* Forward VGA addresses */
+#define  PCI_BRIDGE_CTL_MASTER_ABORT 0x20  /* Report master aborts */
+#define  PCI_BRIDGE_CTL_BUS_RESET 0x40	/* Secondary bus reset */
+#define  PCI_BRIDGE_CTL_FAST_BACK 0x80	/* Fast Back2Back enabled on secondary interface */
+
+/* Header type 2 (CardBus bridges) */
+#define PCI_CB_CAPABILITY_LIST	0x14
+/* 0x15 reserved */
+#define PCI_CB_SEC_STATUS	0x16	/* Secondary status */
+#define PCI_CB_PRIMARY_BUS	0x18	/* PCI bus number */
+#define PCI_CB_CARD_BUS		0x19	/* CardBus bus number */
+#define PCI_CB_SUBORDINATE_BUS	0x1a	/* Subordinate bus number */
+#define PCI_CB_LATENCY_TIMER	0x1b	/* CardBus latency timer */
+#define PCI_CB_MEMORY_BASE_0	0x1c
+#define PCI_CB_MEMORY_LIMIT_0	0x20
+#define PCI_CB_MEMORY_BASE_1	0x24
+#define PCI_CB_MEMORY_LIMIT_1	0x28
+#define PCI_CB_IO_BASE_0	0x2c
+#define PCI_CB_IO_BASE_0_HI	0x2e
+#define PCI_CB_IO_LIMIT_0	0x30
+#define PCI_CB_IO_LIMIT_0_HI	0x32
+#define PCI_CB_IO_BASE_1	0x34
+#define PCI_CB_IO_BASE_1_HI	0x36
+#define PCI_CB_IO_LIMIT_1	0x38
+#define PCI_CB_IO_LIMIT_1_HI	0x3a
+#define  PCI_CB_IO_RANGE_MASK	~0x03
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_CB_BRIDGE_CONTROL	0x3e
+#define  PCI_CB_BRIDGE_CTL_PARITY	0x01	/* Similar to standard bridge control register */
+#define  PCI_CB_BRIDGE_CTL_SERR		0x02
+#define  PCI_CB_BRIDGE_CTL_ISA		0x04
+#define  PCI_CB_BRIDGE_CTL_VGA		0x08
+#define  PCI_CB_BRIDGE_CTL_MASTER_ABORT	0x20
+#define  PCI_CB_BRIDGE_CTL_CB_RESET	0x40	/* CardBus reset */
+#define  PCI_CB_BRIDGE_CTL_16BIT_INT	0x80	/* Enable interrupt for 16-bit cards */
+#define  PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100	/* Prefetch enable for both memory regions */
+#define  PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200
+#define  PCI_CB_BRIDGE_CTL_POST_WRITES	0x400
+#define PCI_CB_SUBSYSTEM_VENDOR_ID 0x40
+#define PCI_CB_SUBSYSTEM_ID	0x42
+#define PCI_CB_LEGACY_MODE_BASE	0x44	/* 16-bit PC Card legacy mode base address (ExCa) */
+/* 0x48-0x7f reserved */
+
+/* Capability lists */
+
+#define PCI_CAP_LIST_ID		0	/* Capability ID */
+#define  PCI_CAP_ID_PM		0x01	/* Power Management */
+#define  PCI_CAP_ID_AGP		0x02	/* Accelerated Graphics Port */
+#define  PCI_CAP_ID_VPD		0x03	/* Vital Product Data */
+#define  PCI_CAP_ID_SLOTID	0x04	/* Slot Identification */
+#define  PCI_CAP_ID_MSI		0x05	/* Message Signalled Interrupts */
+#define  PCI_CAP_ID_CHSWP	0x06	/* CompactPCI HotSwap */
+#define  PCI_CAP_ID_HT          0x08
+#define PCI_CAP_LIST_NEXT	1	/* Next capability in the list */
+#define PCI_CAP_FLAGS		2	/* Capability defined flags (16 bits) */
+#define PCI_CAP_SIZEOF		4
+
+/* Power Management Registers */
+
+#define  PCI_PM_CAP_VER_MASK	0x0007	/* Version */
+#define  PCI_PM_CAP_PME_CLOCK	0x0008	/* PME clock required */
+#define  PCI_PM_CAP_AUX_POWER	0x0010	/* Auxilliary power support */
+#define  PCI_PM_CAP_DSI		0x0020	/* Device specific initialization */
+#define  PCI_PM_CAP_D1		0x0200	/* D1 power state support */
+#define  PCI_PM_CAP_D2		0x0400	/* D2 power state support */
+#define  PCI_PM_CAP_PME		0x0800	/* PME pin supported */
+#define PCI_PM_CTRL		4	/* PM control and status register */
+#define  PCI_PM_CTRL_STATE_MASK	0x0003	/* Current power state (D0 to D3) */
+#define  PCI_PM_CTRL_PME_ENABLE	0x0100	/* PME pin enable */
+#define  PCI_PM_CTRL_DATA_SEL_MASK	0x1e00	/* Data select (??) */
+#define  PCI_PM_CTRL_DATA_SCALE_MASK	0x6000	/* Data scale (??) */
+#define  PCI_PM_CTRL_PME_STATUS	0x8000	/* PME pin status */
+#define PCI_PM_PPB_EXTENSIONS	6	/* PPB support extensions (??) */
+#define  PCI_PM_PPB_B2_B3	0x40	/* Stop clock when in D3hot (??) */
+#define  PCI_PM_BPCC_ENABLE	0x80	/* Bus power/clock control enable (??) */
+#define PCI_PM_DATA_REGISTER	7	/* (??) */
+#define PCI_PM_SIZEOF		8
+
+/* AGP registers */
+
+#define PCI_AGP_VERSION		2	/* BCD version number */
+#define PCI_AGP_RFU		3	/* Rest of capability flags */
+#define PCI_AGP_STATUS		4	/* Status register */
+#define  PCI_AGP_STATUS_RQ_MASK	0xff000000	/* Maximum number of requests - 1 */
+#define  PCI_AGP_STATUS_SBA	0x0200	/* Sideband addressing supported */
+#define  PCI_AGP_STATUS_64BIT	0x0020	/* 64-bit addressing supported */
+#define  PCI_AGP_STATUS_FW	0x0010	/* FW transfers supported */
+#define  PCI_AGP_STATUS_RATE4	0x0004	/* 4x transfer rate supported */
+#define  PCI_AGP_STATUS_RATE2	0x0002	/* 2x transfer rate supported */
+#define  PCI_AGP_STATUS_RATE1	0x0001	/* 1x transfer rate supported */
+#define PCI_AGP_COMMAND		8	/* Control register */
+#define  PCI_AGP_COMMAND_RQ_MASK 0xff000000  /* Master: Maximum number of requests */
+#define  PCI_AGP_COMMAND_SBA	0x0200	/* Sideband addressing enabled */
+#define  PCI_AGP_COMMAND_AGP	0x0100	/* Allow processing of AGP transactions */
+#define  PCI_AGP_COMMAND_64BIT	0x0020 	/* Allow processing of 64-bit addresses */
+#define  PCI_AGP_COMMAND_FW	0x0010 	/* Force FW transfers */
+#define  PCI_AGP_COMMAND_RATE4	0x0004	/* Use 4x rate */
+#define  PCI_AGP_COMMAND_RATE2	0x0002	/* Use 4x rate */
+#define  PCI_AGP_COMMAND_RATE1	0x0001	/* Use 4x rate */
+#define PCI_AGP_SIZEOF		12
+
+/* Slot Identification */
+
+#define PCI_SID_ESR		2	/* Expansion Slot Register */
+#define  PCI_SID_ESR_NSLOTS	0x1f	/* Number of expansion slots available */
+#define  PCI_SID_ESR_FIC	0x20	/* First In Chassis Flag */
+#define PCI_SID_CHASSIS_NR	3	/* Chassis Number */
+
+/* Message Signalled Interrupts registers */
+
+#define PCI_MSI_FLAGS		2	/* Various flags */
+#define  PCI_MSI_FLAGS_64BIT	0x80	/* 64-bit addresses allowed */
+#define  PCI_MSI_FLAGS_QSIZE	0x70	/* Message queue size configured */
+#define  PCI_MSI_FLAGS_QMASK	0x0e	/* Maximum queue size available */
+#define  PCI_MSI_FLAGS_ENABLE	0x01	/* MSI feature enabled */
+#define PCI_MSI_RFU		3	/* Rest of capability flags */
+#define PCI_MSI_ADDRESS_LO	4	/* Lower 32 bits */
+#define PCI_MSI_ADDRESS_HI	8	/* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */
+#define PCI_MSI_DATA_32		8	/* 16 bits of data for 32-bit devices */
+#define PCI_MSI_DATA_64		12	/* 16 bits of data for 64-bit devices */
+
+/*
+ * The PCI interface treats multi-function devices as independent
+ * devices.  The slot/function address of each device is encoded
+ * in a single byte as follows:
+ *
+ *	7:3 = slot
+ *	2:0 = function
+ */
+#define PCI_DEVFN(slot,func)	((((slot) & 0x1f) << 3) | ((func) & 0x07))
+#define PCI_SLOT(devfn)		(((devfn) >> 3) & 0x1f)
+#define PCI_FUNC(devfn)		((devfn) & 0x07)
+#define PCI_BDF(bus,dev,func)	((bus) << 16 | (dev) << 11 | (func) << 8)
+
+
+#include <device/resource.h>
+#include <device/device.h>
+#include <device/pci_ops.h>
+
+
+struct pci_driver {
+	struct device_operations *ops;
+	unsigned short vendor;
+	unsigned short device;
+};
+
+#define __pci_driver __attribute__ ((unused,__section__(".rodata.pci_driver")))
+extern struct pci_driver pci_drivers[];
+extern struct pci_driver epci_drivers[];
+
+
+struct device_operations default_pci_ops_dev;
+struct device_operations default_pci_ops_bus;
+struct device_operations default_pci_ops_root;
+
+
+void pci_dev_read_resources(struct device *dev);
+void pci_bus_read_resources(struct device *dev);
+void pci_dev_set_resources(struct device *dev);
+unsigned int pci_scan_bridge(struct device *bus, unsigned int max);
+
+#define PCI_IO_BRIDGE_ALIGN 4096
+#define PCI_MEM_BRIDGE_ALIGN (1024*1024)
+
+#endif /* PCI_H */
--- a/src/include/device/pci_ids.h
+++ b/src/include/device/pci_ids.h
--- a/src/include/device/pci_ops.h
+++ b/src/include/device/pci_ops.h
@@ -0,0 +1,15 @@
+#ifndef PCI_OPS_H
+#define PCI_OPS_H
+
+#include <stdint.h>
+struct device;
+
+int pci_read_config_byte(struct device *dev, uint8_t where, uint8_t *val);
+int pci_read_config_word(struct device *dev, uint8_t where, uint16_t *val);
+int pci_read_config_dword(struct device *dev, uint8_t where, uint32_t *val);
+int pci_write_config_byte(struct device *dev, uint8_t where, uint8_t val);
+int pci_write_config_word(struct device *dev, uint8_t where, uint16_t val);
+int pci_write_config_dword(struct device *dev, uint8_t where, uint32_t val);
+void pci_set_method(void);
+
+#endif /* PCI_OPS_H */
--- a/src/include/device/resource.h
+++ b/src/include/device/resource.h
@@ -0,0 +1,70 @@
+#ifndef RESOURCE_H
+#define RESOURCE_H
+
+
+#define IORESOURCE_BITS		0x000000ff	/* Bus-specific bits */
+
+#define IORESOURCE_IO		0x00000100	/* Resource type */
+#define IORESOURCE_MEM		0x00000200
+#define IORESOURCE_IRQ		0x00000400
+#define IORESOURCE_DMA		0x00000800
+
+#define IORESOURCE_PREFETCH	0x00001000	/* No side effects */
+#define IORESOURCE_READONLY	0x00002000
+#define IORESOURCE_CACHEABLE	0x00004000
+#define IORESOURCE_RANGELENGTH	0x00008000
+#define IORESOURCE_SHADOWABLE	0x00010000
+#define IORESOURCE_BUS_HAS_VGA	0x00020000
+
+#define IORESOURCE_SET		0x80000000
+
+/* PCI specific resource bits */
+#define IORESOURCE_PCI64	(1<<0)	/* 64bit long pci resource */
+#define IORESOURCE_PCI_BRIDGE	(1<<1)  /* A bridge pci resource */
+
+/* ISA PnP IRQ specific bits (IORESOURCE_BITS) */
+#define IORESOURCE_IRQ_HIGHEDGE		(1<<0)
+#define IORESOURCE_IRQ_LOWEDGE		(1<<1)
+#define IORESOURCE_IRQ_HIGHLEVEL	(1<<2)
+#define IORESOURCE_IRQ_LOWLEVEL		(1<<3)
+
+/* ISA PnP DMA specific bits (IORESOURCE_BITS) */
+#define IORESOURCE_DMA_TYPE_MASK	(3<<0)
+#define IORESOURCE_DMA_8BIT		(0<<0)
+#define IORESOURCE_DMA_8AND16BIT	(1<<0)
+#define IORESOURCE_DMA_16BIT		(2<<0)
+
+#define IORESOURCE_DMA_MASTER		(1<<2)
+#define IORESOURCE_DMA_BYTE		(1<<3)
+#define IORESOURCE_DMA_WORD		(1<<4)
+
+#define IORESOURCE_DMA_SPEED_MASK	(3<<6)
+#define IORESOURCE_DMA_COMPATIBLE	(0<<6)
+#define IORESOURCE_DMA_TYPEA		(1<<6)
+#define IORESOURCE_DMA_TYPEB		(2<<6)
+#define IORESOURCE_DMA_TYPEF		(3<<6)
+
+
+/* ISA PnP memory I/O specific bits (IORESOURCE_BITS) */
+#define IORESOURCE_MEM_WRITEABLE	(1<<0)	/* dup: IORESOURCE_READONLY */
+#define IORESOURCE_MEM_CACHEABLE	(1<<1)	/* dup: IORESOURCE_CACHEABLE */
+#define IORESOURCE_MEM_RANGELENGTH	(1<<2)	/* dup: IORESOURCE_RANGELENGTH */
+#define IORESOURCE_MEM_TYPE_MASK	(3<<3)
+#define IORESOURCE_MEM_8BIT		(0<<3)
+#define IORESOURCE_MEM_16BIT		(1<<3)
+#define IORESOURCE_MEM_8AND16BIT	(2<<3)
+#define IORESOURCE_MEM_SHADOWABLE	(1<<5)	/* dup: IORESOURCE_SHADOWABLE */
+#define IORESOURCE_MEM_EXPANSIONROM	(1<<6)
+
+struct resource {
+	unsigned long base;	/* Base address of the resource */
+	unsigned long size;	/* Size of the resource */
+	unsigned long limit;	/* Largest valid value base + size -1 */
+	unsigned long flags;	/* Descriptions of the kind of resource */
+	unsigned long index;	/* Bus specific per device resource id */
+	unsigned char align;	/* Required alignment (base 2) of the resource */
+	unsigned char gran;	/* Granularity (base 2) of the resource */
+	/* Alignment must be >= the granularity of the resource */
+};
+
+#endif /* RESOURCE_H */