mb/google/trulo/var/orisa: Add memory config

Fill in memory config based on the the schematic_20240607.

BUG=b:333486830
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot

Change-Id: I1456f7385e092b606fc0a35b25f3454600af8b23
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82662
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>

src/mainboard/google/brya/variants/orisa/Makefile.mk

@@ -2,4 +2,5 @@
 
 bootblock-y += gpio.c
 romstage-y += gpio.c
+romstage-y += memory.c
 ramstage-y += gpio.c

src/mainboard/google/brya/variants/orisa/memory.c

@@ -0,0 +1,111 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+
+#include <baseboard/variants.h>
+#include <gpio.h>
+#include <soc/romstage.h>
+
+static const struct mb_cfg variant_memcfg = {
+	.type = MEM_TYPE_LP5X,
+
+	.rcomp = {
+		/* Baseboard uses only 100ohm Rcomp resistors */
+		.resistor = 100,
+	},
+
+	/* DQ byte map */
+	.lpx_dq_map = {
+		.ddr0 = {
+			.dq0 = { 12,  9, 10, 11, 14, 13,  8, 15 },
+			.dq1 = {  3,  1,  2,  0,  4,  7,  5,  6 },
+		},
+		.ddr1 = {
+			.dq0 = {  3,  1,  2,  0,  4,  7,  5,  6 },
+			.dq1 = { 13,  9,  8, 11, 10, 14, 15, 12 },
+		},
+		.ddr2 = {
+			.dq0 = {  2,  1,  3,  0,  4,  6,  5,  7 },
+			.dq1 = {  8,  9, 10, 11, 13, 14, 12, 15 },
+		},
+		.ddr3 = {
+			.dq0 = {  3,  0,  1,  2,  5,  6,  4,  7 },
+			.dq1 = { 13,  9, 11,  8, 14, 15, 10, 12 },
+		},
+		.ddr4 = {
+			.dq0 = { 12,  9, 10, 11, 14, 13,  8, 15 },
+			.dq1 = {  3,  1,  2,  0,  4,  7,  5,  6 },
+		},
+		.ddr5 = {
+			.dq0 = {  3,  1,  2,  0,  4,  7,  5,  6 },
+			.dq1 = { 13,  9,  8, 11, 10, 14, 15, 12 },
+		},
+		.ddr6 = {
+			.dq0 = {  2,  1,  3,  0,  4,  6,  5,  7 },
+			.dq1 = {  8,  9, 10, 11, 13, 14, 12, 15 },
+		},
+		.ddr7 = {
+			.dq0 = {  3,  0,  1,  2,  5,  6,  4,  7 },
+			.dq1 = { 13,  9, 11,  8, 14, 15, 10, 12 },
+		},
+	},
+
+	/* DQS CPU<>DRAM map */
+	.lpx_dqs_map = {
+		.ddr0 = { .dqs0 = 1, .dqs1 = 0 },
+		.ddr1 = { .dqs0 = 0, .dqs1 = 1 },
+		.ddr2 = { .dqs0 = 0, .dqs1 = 1 },
+		.ddr3 = { .dqs0 = 0, .dqs1 = 1 },
+		.ddr4 = { .dqs0 = 1, .dqs1 = 0 },
+		.ddr5 = { .dqs0 = 0, .dqs1 = 1 },
+		.ddr6 = { .dqs0 = 0, .dqs1 = 1 },
+		.ddr7 = { .dqs0 = 0, .dqs1 = 1 },
+	},
+
+	.lp5x_config = {
+		.ccc_config = 0xff,
+	},
+
+	.ect = 1, /* Early Command Training */
+
+	.UserBd = BOARD_TYPE_MOBILE,
+};
+
+const struct mb_cfg *variant_memory_params(void)
+{
+	return &variant_memcfg;
+}
+
+int variant_memory_sku(void)
+{
+	/*
+	 * Memory configuration board straps
+	 * GPIO_MEM_CONFIG_0	GPP_E1
+	 * GPIO_MEM_CONFIG_1	GPP_E2
+	 * GPIO_MEM_CONFIG_2	GPP_E12
+	 */
+	gpio_t spd_gpios[] = {
+		GPP_E1,
+		GPP_E2,
+		GPP_E12,
+	};
+
+	return gpio_base2_value(spd_gpios, ARRAY_SIZE(spd_gpios));
+}
+
+bool variant_is_half_populated(void)
+{
+	/*
+	 * Ideally half_populated is used in platforms with multiple channels to
+	 * enable only one half of the channel. Alder Lake N has single channel,
+	 * and it would require for new structures to be defined in meminit block
+	 * driver for LPx memory configurations. In order to avoid adding new
+	 * structures, set half_populated to true. This has the same effect as
+	 * having single channel with 64-bit width.
+	*/
+	return true;
+}
+
+void variant_get_spd_info(struct mem_spd *spd_info)
+{
+	spd_info->topo = MEM_TOPO_MEMORY_DOWN;
+	spd_info->cbfs_index = variant_memory_sku();
+}