soc/rockchip: Fix typos

Change-Id: I85ccb9e1458340bd5bc2a0eb9abed8d0eeb2fe65
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>

src/soc/rockchip/common/edp.c

@@ -135,7 +135,7 @@ static void rk_edp_init_analog_func(struct rk_edp *edp)
 
 static void rk_edp_init_aux(struct rk_edp *edp)
 {
-	/* Clear inerrupts related to AUX channel */
+	/* Clear interrupts related to AUX channel */
 	write32(&edp->regs->dp_int_sta, AUX_FUNC_EN_N);
 
 	/* Disable AUX channel module */

src/soc/rockchip/rk3288/hdmi.c

@@ -733,7 +733,7 @@ static int hdmi_read_edid(int block, u8 *buff)
 	u32 trytime = 5;
 	u32 n, j, val;
 
-	/* set ddc i2c clk which devided from ddc_clk to 100khz */
+	/* set ddc i2c clk which derived from ddc_clk to 100kHz */
 	write32(&hdmi_regs->i2cm_ss_scl_hcnt_0_addr, 0x7a);
 	write32(&hdmi_regs->i2cm_ss_scl_lcnt_0_addr, 0x8d);
 	clrsetbits32(&hdmi_regs->i2cm_div, HDMI_I2CM_DIV_FAST_STD_MODE,

src/soc/rockchip/rk3288/tsadc.c

@@ -100,7 +100,7 @@ void tsadc_init(void)
 
 	/*
 	  tsadc iomux must be set after the tshut polarity setting,
-	  since the tshut polarity defalut low active,
+	  since the tshut polarity default low active,
 	  so if you enable tsadc iomux,it will output high
 	 */
 	setbits32(&rk3288_pmu->iomux_tsadc_int, IOMUX_TSADC_INT);

src/soc/rockchip/rk3399/clock.c

@@ -304,7 +304,7 @@ static void rkclk_set_pll(u32 *pll_con, const struct pll_div *div)
 	u32 output_khz = vco_khz / div->postdiv1 / div->postdiv2;
 
 	printk(BIOS_DEBUG, "PLL at %p: fbdiv=%d, refdiv=%d, postdiv1=%d, "
-			   "postdiv2=%d, vco=%u khz, output=%u khz\n",
+			   "postdiv2=%d, vco=%u kHz, output=%u kHz\n",
 			   pll_con, div->fbdiv, div->refdiv, div->postdiv1,
 			   div->postdiv2, vco_khz, output_khz);
 	assert(vco_khz >= VCO_MIN_KHZ && vco_khz <= VCO_MAX_KHZ &&
@@ -485,7 +485,7 @@ void rkclk_init(void)
 
 	/* some cru registers changed by bootrom, we'd better reset them to
 	 * reset/default values described in TRM to avoid confusion in kernel.
-	 * Please consider these threee lines as a fix of bootrom bug.
+	 * Please consider these three lines as a fix of bootrom bug.
 	 */
 	write32(&cru_ptr->clksel_con[12], 0xffff4101);
 	write32(&cru_ptr->clksel_con[19], 0xffff033f);

src/soc/rockchip/rk3399/mipi.c

@@ -319,7 +319,7 @@ static int rk_mipi_dsi_get_lane_bps(struct rk_mipi_dsi *dsi,
 	min_prediv = DIV_ROUND_UP(fref, 40 * MHz);
 	max_prediv = fref / (5 * MHz);
 
-	/* constraint: 80MHz <= Fvco <= 1500Mhz */
+	/* constraint: 80MHz <= Fvco <= 1500MHz */
 	fvco_min = 80 * MHz;
 	fvco_max = 1500 * MHz;
 	min_delta = 1500 * MHz;

src/soc/rockchip/rk3399/tsadc.c

@@ -112,7 +112,7 @@ void tsadc_init(uint32_t polarity)
 
 	/* setup the automatic mode:
 	 * AUTO_PERIOD: interleave between every two accessing of TSADC
-	 * AUTO_DEBOUNCE: only generate interrupt or TSHUT when temprature
+	 * AUTO_DEBOUNCE: only generate interrupt or TSHUT when temperature
 	 *                is higher than COMP_INT for "debounce" times
 	 * AUTO_PERIOD_HT: the interleave between every two accessing after the
 	 *                 temperature is higher than COMP_SHUT or COMP_INT
@@ -123,7 +123,7 @@ void tsadc_init(uint32_t polarity)
 	write32(&rk3399_tsadc->hight_int_debounce, AUTO_DEBOUNCE);
 	write32(&rk3399_tsadc->auto_period_ht, AUTO_PERIOD_HT);
 	write32(&rk3399_tsadc->hight_tshut_debounce, AUTO_DEBOUNCE_HT);
-	/* Enable the src0, negative temprature coefficient */
+	/* Enable the src0, negative temperature coefficient */
 	setbits32(&rk3399_tsadc->auto_con, Q_SEL | SRC0_EN);
 	udelay(100);
 	setbits32(&rk3399_tsadc->auto_con, AUTO_EN);