mb/google/brya/variants/primus: Swap TPM I2C with touchscreen I2C

In next build phase, primus will exchange i2c port for touchscreen and cr50.

BUG=b:207834727
TEST=build pass

Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: Ief1b156b866a9aaa2919f0e209b6439c7019e939
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>

src/mainboard/google/brya/Kconfig

@@ -74,7 +74,8 @@ config DRIVER_TPM_I2C_BUS
 	hex
 	default 0x3 if BOARD_GOOGLE_BRYA0
 	default 0x3 if BOARD_GOOGLE_BRASK
-	default 0x3 if BOARD_GOOGLE_PRIMUS
+	default 0x1 if BOARD_GOOGLE_PRIMUS
+	default 0x3 if BOARD_GOOGLE_PRIMUS4ES
 	default 0x1 if BOARD_GOOGLE_GIMBLE
 	default 0x3 if BOARD_GOOGLE_GIMBLE4ES
 	default 0x3 if BOARD_GOOGLE_REDRIX

src/mainboard/google/brya/variants/primus/gpio.c

@@ -80,10 +80,10 @@ static const struct pad_config early_gpio_table[] = {
 	PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT),
 	/* B4  : PROC_GP3 ==> SSD_PERST_L */
 	PAD_CFG_GPO(GPP_B4, 0, DEEP),
-	/* B7  : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */
+	/* H6  : I2C1_SDA ==> PCH_I2C_TPM_SDA */
-	PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2),
+	PAD_CFG_NF(GPP_H6, NONE, DEEP, NF1),
-	/* B8  : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */
+	/* H7  : I2C1_SCL ==> PCH_I2C_TPM_SCL */
-	PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2),
+	PAD_CFG_NF(GPP_H7, NONE, DEEP, NF1),
 	/*
 	 * D1  : ISH_GP1 ==> FP_RST_ODL
 	 * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down.

src/mainboard/google/brya/variants/primus/overridetree.cb

@@ -42,11 +42,11 @@ chip soc/intel/alderlake
 	#+-------------------+---------------------------+
 	#| GSPI1             | Fingerprint MCU           |
 	#| I2C0              | Audio                     |
-	#| I2C1              | Touchscreen               |
+	#| I2C1              | cr50 TPM. Early init is   |
-	#| I2C2              |                           |
-	#| I2C3              | cr50 TPM. Early init is   |
 	#|                   | required to set up a BAR  |
 	#|                   | for TPM communication     |
+	#| I2C2              |                           |
+	#| I2C3              | Touchscreen               |
 	#| I2C5              | Trackpad                  |
 	#+-------------------+---------------------------+
 	register "common_soc_config" = "{
@@ -54,14 +54,20 @@ chip soc/intel/alderlake
 			.speed = I2C_SPEED_FAST,
 		},
 		.i2c[1] = {
+			.early_init = 1,
 			.speed = I2C_SPEED_FAST,
+			.rise_time_ns = 600,
+			.fall_time_ns = 400,
+			.data_hold_time_ns = 50,
 		},
 		.i2c[2] = {
 			.speed = I2C_SPEED_FAST,
 		},
 		.i2c[3] = {
-			.early_init = 1,
 			.speed = I2C_SPEED_FAST,
+			.rise_time_ns = 650,
+			.fall_time_ns = 400,
+			.data_hold_time_ns = 50,
 		},
 		.i2c[5] = {
 			.speed = I2C_SPEED_FAST,
@@ -197,6 +203,13 @@ chip soc/intel/alderlake
 			end
 		end #I2C0
 		device ref i2c1 on
+			chip drivers/i2c/tpm
+				register "hid" = ""GOOG0005""
+				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
+				device i2c 50 on end
+			end
+		end
+		device ref i2c3 on
 			chip drivers/i2c/hid
 				register "generic.hid" = ""ELAN9050""
 				register "generic.desc" = ""ELAN Touchscreen""
@@ -232,13 +245,6 @@ chip soc/intel/alderlake
 				device i2c 0x40 on end
 			end
 		end
-		device ref i2c3 on
-			chip drivers/i2c/tpm
-				register "hid" = ""GOOG0005""
-				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
-				device i2c 50 on end
-			end
-		end
 		device ref i2c5 on
 			chip drivers/i2c/generic
 				register "hid" = ""ELAN0000""