There is an on-board PCI device where bus master has to be enabled in
PCI configuration space. As there is no need for a complete PCI driver
for this device just set the bus master bit in mainboard_final().
Change-Id: I1ef4a7774d4ca75c230063debbc63d03486fed6f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
On this mainboard there is a legacy PCI device, which is connected to
the PCIe root port via a PCIe-2-PCI bridge. This device only supports
legacy interrupt routing. For this reason we have to adjust the PIR6
register (0x314c) which is responsible for PCIe device 13h and 14h. This
means that the interrupt routing will also be the same for both PCIe
devices. The bridge is connected to PCIe root port 2 and 3 over two
lanes (Device 13.0 and 13.1).
The following routing is required:
INTA#->PIRQD#, INTB#->PIRQA#, INTC#->PIRQB#, INTD#->PIRQC#
Change-Id: I5028c26769a2122b1c609ad7789c9949e3cb7a87
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29513
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
EC_SYNC_IRQ from EC to host is level-triggered in practice and
configuring it as edge-triggered on the host results in host missing
events if there are multiple events queued on the EC side. This is
because Linux kernel driver reads one event per irq and the EC does
not de-assert the interrupt line until all events are drained
out. This results in event queue being filled up completely on the EC
and the host failing to see any of those events.
This change configures EC_SYNC_IRQ as level triggered to allow the
host to read events from the the EC as long as the line is asserted.
BUG=b:118949877
Change-Id: Id3fcfa0445f83865d57975a7bbc179dca047ba4c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
* Remove dead code
* Add support for types 2504 and 2505
* Print dock info at romstage entry
* Improve dock disconnect for type 2505
* Move defines into dock.h for future ACPI code
* Reduce timeouts according to spec to decrease boot time on error
* Fix no docking detection (reduces boot time by 1 second)
* Configure GPIO LDN before reading GPIOs
* Use Kconfig values instead of fixed defines
* Add documentation
Tested on Lenovo T500 with docking 2504 and 2505.
Change-Id: Ic4510ffadc67da95961cecd51a6d8ed856b3ac99
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/29418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change disables HECI1 device at the end of boot sequence. It uses
the P2SB messaging to disable HECI1 device before hiding P2SB and
dropping privilege level.
BUG=b:119074978
BRANCH=None
TEST=Verified that HECI1 device is not visible in lspci on octopus.
Change-Id: Id6abfd0c71a466d0cf8f19ae9b91f1d3446e3d09
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29534
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kane Chen <kane.chen@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change 76ab2b7 ("arch/x86: allow global .bss objects without
CAR_GLOBAL") allowed use of global .bss objects and hence moved around
the macros resulting in car_active returning 0 even for those boards
where CAR is actually active but do not require global migration. This
resulted in boards getting stuck when doing a reset in verstage because
the code flow incorrectly assumed that there was no CAR active and
hence triggered a cache invalidate.
This change fixes the above issue by returning 1 for car_active if
ENV_CACHE_AS_RAM is set even if global migration is not required.
BUG=b:109717603
TEST=Verified that board reset does not trigger cache invalidate in
verstage and does not result in board hang.
Change-Id: I182f3e4277c57d6c50f7fcac2be72514896b3c61
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peichao Li <peichao.wang@bitland.corp-partner.google.com>
Reviewed-by: Nick Chen <nickchen@ami.corp-partner.google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
1. Add two parameters for panel initialization timing.
> lvds_poseq_varybl_to_blon
> lvds_poseq_blon_to_varybl
2. The BL_PWM is controlled by APU_EDP_BKLTEN_L/APU_DP_VARY_BL/
EDP_BKLTEN_L, so move APU_EDP_BKLTEN_L to early init stage,
and be enabled depends on SKU, thus we can control the delay
time by config APU_DP_VARY_BL.
BUG=b:118011567
TEST=emerge-grunt coreboot.
Change-Id: Ib20c48813b208d697b950b2f02a70a690e483fdb
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
GPIOs that use GPI_APIC setting with DEEP can cause an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ strom after S3 resume.
For sarien/arcada these are all runtime IRQs only, not wake capable.
Change-Id: Iec3706a3b47b54abbacd06081910f389979c330f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Select the option to disable eSPI when ACPI is enabled so the EC
is unable to assert an SMI when booted into the OS. There is a
kernel driver that implements the same mailbox interface so it
cannot also be used by the SMI handler.
Change-Id: I8bafc749f22aed5595e19e773762ee8b038950b9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add an option that will disable eSPI SMI when ACPI mode is enabled,
and re-enable eSPI SMI when ACPI mode is disabled. Additionally it
ensures eSPI SMI is disabled on the ACPI OS resume path.
This allows a mainboard to ensure that the Embedded Controller will
not be able to assert SMI at runtime when booted into an ACPI aware
operating system.
This was tested on a Sarien board with the Wilco EC to ensure that
the eSPI SMI enable bit is clear when booted into the OS, and remains
clear after resume.
Change-Id: Ic305c3498dfa4b8166cfdb070fc404dd4618ba3c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Make the firmware slot configuration in VBOOT selectable. The following
three modes are available:
-RO only
-RO + RW_A
-RO + RW_A + RW_B
The mode "RO only" is the lowest mode with no safety during update.
You can select either RW_A or RW_AB via Kconfig which will add the
selected parttions to the final image.
Change-Id: I278fc060522b13048b00090b8e5261c14496f56e
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/27714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
This patch also add new SKL PCH-H device id's in soc platform reporting and
common lpc driver.
BUG=None
TEST=Booted kabylake RVP11 with HM175 SKL PCH-H and verified the device id
in serial logs.
Change-Id: I8c04bf8d9c27caad800427a5c29da869da1d445d
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/29432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Boon Tiong Teo <boon.tiong.teo@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
GPIO's that use GPI_APIC setting with DEEP causes an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ storm after S3 resume and hence
configuring GPP_D9 and GPP_D10 to use PLTRST.
BUG=b:119202293
TEST=none
Change-Id: I98d71100f28fb9bae05db3fb7d9afcb3f81beb43
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29538
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_C11 (FPMCU_INT_L) was set to DEEP, causing problems with S3.
Changed GPP_C11 configuration to use PLTRST instead.
BUG=b:114196791
TEST=Build, flash, boot nocturne, log in to kernel and execute
the following two commands and verify it passes :
echo 0 > /var/lib/power_manager/suspend_to_idle && restart powerd
sudo suspend_stress_test -c 2
Change-Id: I008532fce963c51a435378001440ac72b5ebfffc
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change allows to redirect coreboot console output to COM2 by
setting appropriate UART index in Console menu in Kconfig.
Change is helpful for users which would like to use COM1 port for
other purposes, because COM1 is the only port with hardware flow
control.
Change-Id: I39f88d7e7794f603775a985afe07fef349172e5f
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/29255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
VB2_LIB will be used across all stages to hash data. Add it to postcar
stage sources so that it is compiled if postcar exists. In this way the
new function tpm_measure_region() introduced in commit
61322d7 (security/tpm: Add function to measure a region device)
can be used in every stage.
Change-Id: I933d33b0188d1b123bb4735722b6086e7786624f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/29465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
* Move all implementations to into common folder.
* Add rtc.c for rtc based functions
Allows all Intel based platforms to use VBOOT_VBNV_CMOS.
Change-Id: Ia494e6d418af6f907c648376674776c54d95ba71
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/29427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
