Non-dts based systems can pass mclk to da7219 driver by
this property.
BUG=b:74570989
TEST=Enabled clock in kernel driver using the property
Change-Id: I2e10769e5b3c6b3aa30f340fe0e88c29b87430cb
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Some touchscreens need to adhere to certain timings during the power
off sequence as well as during the power on sequence. Adding
reset_off_delay_ms, enable_off_delay_ms, and stop_off_delay_ms to
accommodate these devices.
BUG=b:78311818
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: Idb4a5dbe56eee4749d2f2b514e92c28fb2c6078f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/25882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The chip PCA9538 is a 8 bit I/O expander connected to the systems I2C
bus. Add a chip driver to support this chip.
Beside the pure chip driver two interface functions are provided to read
the state of the pins and write output values to the pins.
As the slave address of this chip is hardware configurable the function
pca9538_get_dev() is used to get the right slave address. This function
needs to be implemented in mainboard code if one needs to use the
interface functions to read and write I/O state.
Change-Id: Ic856123b4f4c8b721928ee3a2a4bb37833ea4b20
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/23748
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The designware i2c controller indicates that the slave address
shouldn't be programmed while the controller is enabled. Therefore,
switch the ordering of the slave target address and the enable.
Additionally, ensure the controller is disabled prior to the
start of the slave programming sequence.
Lastly, chunk up the i2c_msg segments at differing slave address
boundaries. That allows for simpler programming for the controller
by only doing one slave address transaction chunk at a time.
BUG=b:70232394,b:69250772
Change-Id: Iebc08e2db847cb182fad98e0ff3d799b9a64aca7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Grunt (a amd-stoneyridge based platform) uses a GPIO to interface with
the tpm. This change allows devicetree entries to use a irq_gpio entry
to describe the interface with the TPM.
BUG=b:72655090
Change-Id: I08289891408d7176f68eb9c67f7a417a2448c2de
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Right now dw_i2c_get_soc_cfg() is expecting the SoC to implement
that callback for obtaining the bus config. However, we're currently
forcing another parameter of struct device so one can do the lookup.
This works for Intel-based systems since the struct device was needed
to program the BAR, etc. However, from an API standpoint, it just
complicates matters by needing to obtain the struct device. The SoC
already has knowlege of its own devices so it can get the config
itself by bus number. Therefore, remove that contraint from the API.
BUG=b:70232394
Change-Id: Id8558f5deedda0963a46a532a7bf984e168fb270
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23420
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In ramstage the device_operations are needed for the i2c designware
host controller. Move the intel/common/block/i2c implementation
into the generic driver so other platforms can take advantage of it.
BUG=b:72121803
Change-Id: Id249933fadcc016bfba00e7a6d65f56dfc220724
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
If one wants to implement both i2c_bus.h and i2c_simple.h APIs
the compilation unit needs to be guarded or coordinated carefully
with different compilation units. Instead, name the i2c_bus
functions with _dev such that it indicates that they operate on
struct device. One other change to allow i2c_bus.h to be built in
non-ramstage environments is to ensure DEVTREE_CONST is used for
the dev field in struct bus.
BUG=b:72121803
Change-Id: I267e27e62c95013e8ff8b0728dbe9e7b523de453
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
* Move code from src/lib and src/include into src/security/tpm
* Split TPM TSS 1.2 and 2.0
* Fix header includes
* Add a new directory structure with kconfig and makefile includes
Change-Id: Id15a9aa6bd367560318dfcfd450bf5626ea0ec2b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The Cr50 i2c driver provides separate entry points for probing and
initialization, but probing function does not really do much.
It also claims and releases locality on every coreboot stage, but
there is no need for this - locality should be definitely claimed
after reset and then it could be retained through the boot process.
On top of that the driver does not properly account for long time it
could take the Cr50 chip to come around to reset processing if TPM
reset request was posted during a lengthy TPM operation.
This patch addresses the issues as follows:
- tpm_vendor_probe() and tpm_vendor_cleanup() become noops, kept
around to conform to the expected driver API.
- tpm_vendor_init() invokes a function to process TPM reset only in
the first stage using TPM (typically verstage), the function
checks if locality is claimed and if so - waits for it to be
released, which indicates that TPM reset processing is over.
- before claiming locality check if it is already taken, and if so -
just proceed.
BRANCH=none
BUG=b:65867313, b:68729265
TEST=Verified that reef no longer hangs during EC reboot and
firmware_Cr50ClearTPMOwner (not yet merged) tests.
Change-Id: Iba8445caf1342e3a5fefcb2664b0759a1a8e84e3
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/22554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In case the TPM is doing a long crypto operation the initial probe
could be very delayed. Rather than end up in recovery make the delay
long enough to accommodate the (current) long crypto times.
BUG=b:65867313, b:68729265
TEST=Verified that Soraka no longer hangs during EC reboot test.
Change-Id: I3bccff70e001dfc065c24be8ad34ef239a144db1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change list adds imon and vmon slot numbers as params for
Maxim 98927 driver. These values are looked up in the kernel driver
to confiure IV feedback for audio playback on speakers.
BUG=b:36724448
TEST=After boot, the register dump for Max98927 codecs should have
imon and vmon slots numbers set in 0x1e register.
Change-Id: I21d72ba91af83782587f11018b2d1d1c8d4f676c
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There is at least one I2C device (being used by Soraka) that has 3
controls -- enable, reset and stop. If the stop gpio is not put into
the right state when turning off the device in suspend mode, then it
causes leakage. Thus, we need control in power resource to be able to
stop the device when entering suspend state.
BUG=b:64987428
TEST=Verified on soraka that touchscreen stop is correctly configured
on suspend.
Change-Id: Iae5ec7eb3972c5c7f80956d60d0d3c321bbefb0f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21249
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Replaces the ics/954309 driver with a more generic version to
accommodate clockgens with a different amount of registers.
It also features a mask to only touch certain bits of the clockgen.
TODO: set appropriate mask for X60/T60 since the datasheets for their
clockgens can be found.
Change-Id: Ie43c4de7891a39f2f443e78213ecd688134e68d7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Add support for providing additional free form device properties via
devicetree in order to make this driver suitable for kernel drivers
that need additional board-specific device properties.
This currently allows adding up to 10 additional properties to a device.
BUG=b:63413023
TEST=manual testing to ensure that newly added properties are in SSDT
Change-Id: I2b8ceb208f4aba01053746547def6d07c8f8f3a2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/21270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Our current struct for I2C segments `i2c_seg` was close to being compa-
tible to the Linux version `i2c_msg`, close to being compatible to SMBus
and close to being readable (e.g. what was `chip` supposed to mean?) but
turned out to be hard to fix.
Instead of extending it in a backwards compatible way (and not touching
current controller drivers), replace it with a Linux source compatible
`struct i2c_msg` and patch all the drivers and users with Coccinelle.
The new `struct i2c_msg` should ease porting drivers from Linux and help
to write SMBus compatible controller drivers.
Beside integer type changes, the field `read` is replaced with a generic
field `flags` and `chip` is renamed to `slave`.
Patched with Coccinelle using the clumsy spatch below and some manual
changes:
* Nested struct initializers and one field access skipped by Coccinelle.
* Removed assumption in the code that I2C_M_RD is 1.
* In `i2c.h`, changed all occurences of `chip` to `slave`.
@@ @@
-struct i2c_seg
+struct i2c_msg
@@ identifier msg; expression e; @@
(
struct i2c_msg msg = {
- .read = 0,
+ .flags = 0,
};
|
struct i2c_msg msg = {
- .read = 1,
+ .flags = I2C_M_RD,
};
|
struct i2c_msg msg = {
- .chip = e,
+ .slave = e,
};
)
@@ struct i2c_msg msg; statement S1, S2; @@
(
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1 else S2
|
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1
)
@@ struct i2c_msg *msg; statement S1, S2; @@
(
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1 else S2
|
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1
)
@@ struct i2c_msg msg; expression e; @@
(
-msg.read = 0;
+msg.flags = 0;
|
-msg.read = 1;
+msg.flags = I2C_M_RD;
|
-msg.read = e;
+msg.flags = e ? I2C_M_RD : 0;
|
-!!(msg.read)
+(msg.flags & I2C_M_RD)
|
-(msg.read)
+(msg.flags & I2C_M_RD)
)
@@ struct i2c_msg *msg; expression e; @@
(
-msg->read = 0;
+msg->flags = 0;
|
-msg->read = 1;
+msg->flags = I2C_M_RD;
|
-msg->read = e;
+msg->flags = e ? I2C_M_RD : 0;
|
-!!(msg->read)
+(msg->flags & I2C_M_RD)
|
-(msg->read)
+(msg->flags & I2C_M_RD)
)
@@ struct i2c_msg msg; @@
-msg.chip
+msg.slave
@@ struct i2c_msg *msg; expression e; @@
-msg[e].chip
+msg[e].slave
@ slave disable ptr_to_array @ struct i2c_msg *msg; @@
-msg->chip
+msg->slave
Change-Id: Ifd7cabf0a18ffd7a1def25d1d7059b713d0b7ea9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
According to the datasheet the RTC needs a power rising slope of no more
than 100µs/V to ensure a correct power-on reset. If the mainboard that
hosts the RTC cannot guarantee this, a software reset sequence is needed
in the case where the battery was drained completely.
As the rising slope of the power supply depends on so many parameters
and is highly mainboard specific, refactor the initialization code to
perform a software reset every time a power loss event is recognized by
the RTC.
Change-Id: If64d672e51667523058041bd00e1e50ac047143d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The RTC RX6110SA has several configuration options which might be
interesting to set. To make this setup independent of the driver itself
but let it still be configurable on mainboard level, add more
configuration options to the chip driver.
Change-Id: I7f8b2aa7cd001a887f271be36f655e10e60e778b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The driver for the RTC RX6110SA is designed to be used with I2C bus.
This patch adds the possibility to use SMBus operations to access the
RTC. For this purpose the Kconfig switch RX6110SA_USE_SMBUS is added. It
is not enabled per default so that I2C will be used. One can set this
switch on board level to use SMBus instead.
Change-Id: I4827ae2c544e8002399d94a1159acacd8176c5e9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19978
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The vendor.irq field was originally intended for use as the TPM 1.2
"command complete" interrupt. However, all actual coreboot tpm drivers
and hardware use the vendor.status method of checking command completion
instead, and this irq field is not used.
Let's just remove this unused functionality to simplify the code.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I994c5bfbd18124af9cb81d9684117af766ab0124
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19396
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
The Cr50 TPM uses an IRQ to provide a "status" signal used for hand-shaking
the reception of commands. Real IRQs are not supported in firmware,
however firmware can still poll interrupt status registers for the same
effect.
Commit 94cc485338 ("drivers/i2c/tpm/cr50: Support interrupts for status")
added support for the Cr50 driver on X86 platforms to use a KConfig file
to supply an IRQ which it would poll using acpi_get_gpe. If the IRQ is
not supplied, the Cr50 driver inserts a 20 ms wait.
Unfortunately this doesn't work so well when using the i2c connected Cr50
on ARM platforms. Luckily, a more generic implementation to allow a
mainboard to supply a Cr50 IRQ status polling function was solved for SPI
connected Cr50s by commit 19e3d335bd ("drivers/spi/tpm: using tpm irq to
sync tpm transaction").
Let's refactor the i2c c50 driver to use this same approach, and change
eve and reef boards to make use of DRIVER_TPM_TIS_ACPI_INTERRUPT for
specifying the TPM flow control interrupt.
This essentially reverts these two commits:
48f708d199 drivers/i2c/tpm/cr50: Initialize IRQ status handler before probe
94cc485338 drivers/i2c/tpm/cr50: Support interrupts for status
And ports this commit to i2c/tpm/cr50:
19e3d335bd drivers/spi/tpm: using tpm irq to sync tpm transaction
As a side effect the tpm_vendor_specific IRQ field goes back to its
original usage as the "TPM 1.2 command complete" interrupt, instead of
being repurposed to hold the flow control IRQ.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I004329eae1d8aabda51c46b8504bf210484782b4
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19363
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
1. Move common TIS macros to include/tpm.h.
2. Use common TIS macros while referring to status and access registers.
3. Add a new function claim_locality to properly check for required
access bits and claim locality 0.
BUG=b:36873582
Change-Id: I11bf3e8b6e1f50b7868c9fe4394a858488367287
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19213
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
