According to doc 609208, bit 25 TOL_1V8 in GPP_F4 ~ GPP_F11 DW1
should be clear to prevent unexpected I2C behaviors.
BUG=b:124269499
TEST=boot on nami and check bit 25 TOL_1V8 is clear
Change-Id: I419ef3e89104ad3611e96bbe23a582504b45be0c
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/31368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
CNVi Bluetooth module is at port 8 (zero-indexed) and not at port 9. Fix
the device configuration in the devicetree.
BUG=b:123296264
BRANCH=octopus
TEST=Boots to ChromeOS. Checked the SSDT table to ensure that the reset
gpio is exported under the device \_SB_.PCI0.XHCI.RHUB.HS09. Ensured
that the kernel btusb driver is able to find the exported GPIO in the
devices with CNVi BT module.
Change-Id: I302bc87b18a1aaad77bfb73d607ba28b89b79c14
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change sets default bus speed as I2C_SPEED_FAST instead of
I2C_SPEED_STANDARD when board does not provide any speed. This makes
it similar to all other i2c drivers in coreboot.
BUG=b:124403846
BRANCH=nocturne,atlas
Change-Id: I877d837eea2dfebf78ad7d97a32ee2071500625e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Allow EC region to be readable by BIOS/CPU so that flashrom
can read it.
BUG=b:123199222
TEST=Build coreboot with CONFIG_LOCK_MANAGEMENT_ENGINE set,
run firmware_LockedME test.
Change-Id: I306c74a0893355e57632a22a712b1f4fdaa19306
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change bumps up the BIOS region to 28MiB to use the hole
between SI_ALL and SI_BIOS. Since this SPI flash part is 32MiB, only
the top 16MiB actually gets memory mapped. Thus, the change ensures
that only RW_LEGACY lies in the 12MiB that is not memory mapped.
BUG=b:123443737
TEST=Verified that hatch still boots up. Ensured that fmap dump looks
correct.
Change-Id: I5832d2b89c7eedfc270755e2add16131cfbddff4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Set SerialIoDebugUartNumber to CONFIG_UART_FOR_CONSOLE
SerialIoDebugUartNumber UPD use to select UART Number for Debug Purpose
The default value of SerialIoDebugUartNumber is 2 by default it selects UART 2
so it needs to be initialized as per board config
BUG=b:123702398
Change-Id: I91df4bb756e8ea86db112f1cc28687f48b2c0525
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31375
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Sarien board may have different touchscreen devices that use the
same I2C slave address but have different requirements such as needing
a special driver or ACPI configuration.
In order to support this the devicetree may be configured with multiple
devices at the same address and at boot time the unused devices will be
disabled.
Because there is no GPIO for selecting the device that is present it can
instead be selected with Kconfig, or by setting a VPD key to the HID of
the touchscreen device that is present. The default for Sarien devices
is to not enable a touchscreen for the OS.
The touchscreen selection is currently limited to the Sarien variant but
this also adds the touchscreen HID for Arcada to Kconfig so it would not
complain about the key not being set.
BUG=b:122019253
TEST=This was tested on a Sarien board by adding a second entry to the
devicetree at the same address. Without this change the SSDT is not
loaded by the kernel because of the address conflict. After this change
no touchscreen is enabled by default, but one can be selected with
Kconfig or by setting the 'touchscreen_hid' VPD key.
Change-Id: I4da12b1de0c551bcd89325fe0d8c66c6ffeb7afc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Under some scenarios the key ladder on the Cr50 can get disabled. If
this state is detected, trigger a reboot of the Cr50 to restore full
TPM functionality.
BUG=b:121463033
BRANCH=none
TEST=Built coreboot on sarien and grunt platforms.
TEST=Ran 'gsctool -a -m disable' and reboot. Verified coreboot sends
VENDOR_CC_IMMEDIATE_RESET command to Cr50 and that the Cr50 resets and
then the platform boots normally.
TEST=Performed Cr50 rollback to 0.0.22 which does not support the
VENDOR_CC_TPM_MODE command, confirmed that platform boots normally and
the coreboot log captures the unsupported command.
Tested-by: Keith Short <keithshort@chromium.org>
Change-Id: I70e012efaf1079d43890e909bc6b5015bef6835a
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This implementation configures GPIO (GPP_A21, GPP_C21, GPP_D16)
pad in non-inversion mode i.e Rx PAD state is not inverted as
it is sent from GPIO to IOAPIC.
BUG=b:123315212
TEST=Tested for below:
-> Verify touchpad is working fine.
-> TPM init is successful and boot with fixed boot media.
Change-Id: I6034fd07ccc96a19218d57ef8bb9049c4b963ea5
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/31328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
`off_t` is supposed to be signed, but has no (minimum) width
specified. We'll assume 32-bit minimum, like a `signed long int`.
Also include `sys/types.h` in `libpayload.h` so everything is
available through the latter.
Change-Id: I6c0c1bc1a959db7863cbad2ba29318da162431be
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/31346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
* Adding separate targets for 32bit and 64bit qemu
* Using the riscv64 toolchain for 32bit builds requires setting -m elf32lriscv
* rv32/rv64 is currently configured with ARCH_RISCV_RV32/RV64 and not per stage.
This should probably be changed later.
TEST=Boots to "Payload not loaded." on 32bit qemu using the following commands:
util/riscv/make-spike-elf.sh build/coreboot.rom build/coreboot.elf
qemu-system-riscv32 -M virt -m 1024M -nographic -kernel build/coreboot.elf
Change-Id: I35e59b459d1770df10b51fe9e77dcc474d7c75a0
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/c/31253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: ron minnich <rminnich@gmail.com>
This macro was unnecessarily complex. Trying to avoid an overflow
for unknown reasons, and instead shifted the result into the sign
bit in C. Using a plain number literal that forces C to use an
adequate integer type seems to be safe. We start with 0xffffffff,
subtract `x` and add 1 again. Turned out to be a common pattern
and can't overflow for any positive 32-bit `x`.
Change-Id: Ibb0c5b88a6e42d3ef2990196a5b99ace90ea8ee8
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/31322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
It needs to tune usb2eye setting for these ports:
USB2[4] - type-c port
USB2[6] - camera
BUG=b:122878632
BRANCH=octopus
TEST=built and passed usb2eye SI test
Change-Id: Iaa3adaab2f391e95730b141dc0237ca62c459e5a
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31359
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
