The current CSE firmware update implementation adds CSE RW binary to
FW_MAIN_A/B and this increases the boot time due to the size increase
of these regions leading to higher loading and hashing time.
To mitigate this issue, CSE RW binary is moved from FW_MAIN_A/B to new
region, ME_RW_A/B under RW_SECTON_A/B, and this updates the flashmap to
add ME_RW_A/B region for CSE RW binary.
BUG=b:169077783
TEST=build with cse rw binary, flash and verify volteer2 boots to OS.
Verify me_rw binary is added to ME_RW_A/B region.
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Change-Id: I87da3824933ed2dd8e8ed0fed8686d2a3527faea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46431
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CSE RW blob which will be used by coreboot to update CSE's RW partition,
is packed part of FW_MAIN_A and FW_MAIN_B. This will increase the size of
FW_MAIN_A and FW_MAIN_B. So, accordingly load and hash calculation of
FW_MAIN_A (or FW_MAIN_B) increases during verstage. It increases the boot
time by around 300ms.
The patch address the boot time by pulling CSE RW blob outside of
FW_MAIN_A and FW_MAIN_B. So, it creates new FMAP region within
RW_SECTION_A and RW_SECTION_B and adds CSE RW blob in the new regions
(ME_RW_A and ME_RW_B) as a CBFS file.
Boot Time Measurement details when CSE RW blob is added in the
ME_RW_A and ME_RW_B.
--------------------------------------------------------
| Platform | Old Boot Time | New Boot Time |
--------------------------------------------------------
| JSL | 1.3s | 1.06s |
--------------------------------------------------------
| TGL | 1.63s | 1.36s |
--------------------------------------------------------
Changes:
1. Makefile change to accommodate CSE RW blob into ME_RW_A/ME_RW_B
2. Kconfig change to define CBFS name and default file name for RW blob
metadata.
3. CSE Lite Driver
BUG=b:169077783
TEST=Verified on JSL & TGL platforms
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: If043c9cb99fb822b62633591bf9c5bd75dfe8349
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This patch modifies flash layout to add ME_RW_A/B to add
the CSE RW blob and also enable the CSE RW update feature for
JSLRVP
BUG=b:169077783
TEST= Built for jslrvp. Verified that CSE RW and metadata files
are included in cbfs.
Change-Id: I13baa317a06d00cec0337f08754892c7c8737f5d
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Existing implementation adds the CSE RW update binary to FW_MAIN_A/B
regions and this has significant impact on boot time due to the
increase in the size of these regions leading to higher loading
and hashing time.
This patch modifies flash layout to add new ME_RW_A/B fmap regions
in the RW_SECTION_A/B.
BUG=b:169077783
TEST= Built for dedede. Verified that CSE RW binary is added to the
CSE_RW_A/B fmap region.
Change-Id: I23a3e22a569488b39beb4d12f5b6309c7c742992
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In the existing implementation CSE RW metadata file is generated by
scripts and to avoid incompitable issues between coreboot and the
scripts this patch adds the follwing changes,
* Move the metadata generation to the coreboot Makefile.
* Add CBFS component type struct to create a metadata file during
the compile time.
* Extract the CSE RW version from SOC_INTEL_CSE_RW_VERSION config
and update the major, minor, hotfix and build versions using the
compile time flags.
* Compute the hash of CSE RW binary in hex format using the openssl
and use the HASH_BYTEARRAY macro to convert the 64 character hex
values into the array.
* Add the me_rw.metadata cbfs file to FW_MAIN_A and FW_MAIN_B
regions.
BUG=b:169077783
TEST= Built for dedede. Verify that metadata file was generated
and added to the FW_MAIN_A/B. Extracted it using cbfstool and
verfied that metadata was generated properly.
Change-Id: I412581400a9606fa17cf4398faffda923f07b320
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add the Kconfig to enable the CSE FW Update feature and also to
ensure all the configs are set by the mainboards to enable this
feature.
This config by default disables the CSE FW update feature for JSL
and TGL platforms. It will be enabled after splitting and including
the CSE RW and CSE RW metadata blobs in the CBFS.
BUG=b:169077783
Change-Id: I12810031224f79aba8a4057725ae0ed5a9b36d7e
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This patch adds a kconfig SOC_INTEL_CSE_RW_VERSION to pass the
CSE RW firmware version from the mainboard. This will be extracted
by makefile to update the cse_rw_metadata structure.
Right now the required tool to extract the CSE RW version from
the blob is still under development and after the official version
of the tool is released, version will be extracted by parsing the
CSE RW blob.
BUG=b:169077783
Cq-Depend: chrome-internal:3402224, chrome-internal:3397863,
chromium:2473603, chromium:2473603, chromium:2535950
Change-Id: I62691ee3ede7d4cd21f821381f5d1519f9061fd9
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47430
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SKX FSP doesn't support X2APIC setup, but CPX does. The CPX DMAR
table needs the X2APIC opt out flag set. This fixes the hang loading
a kexec'd kernel. The change is easy to see in the coreboot output:
[DMA Remapping table] Flags: 0x3
or in the DMAR ACPI table.
Change-Id: Iec977c893b70e30875d9a92f24af009c1e90389e
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When the system shuts down, turn the fingerprint sensor off. This sets
the GPIOs correctly for the next boot. The fingerprint sensor was
previously left on, and was just powering down when the rails went low.
On suspend, the fingerprint sensor stays awake and puts itself in a low
powerstate mode based on the SLP_Sx_L pin states.
BUG=b:171837716
TEST=Fingerprint sensor still works after S3, GPIO state on the boot
following a shutdown is low.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3837b58372d8f4a504535e76bd21c667d68f8995
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47311
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
At this point, the zork platform will only use psp_verstage, so remove
the VBOOT_STARTS_IN_BOOTBLOCK option and set code for VBOOT_STARTS-
BEFORE_BOOTBLOCK to always be used.
TEST=Build & Boot Morphius
BRANCH=Zork
BUG=b:172848137
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I30d90fe82c37966a860b52c07a3550dcecf8d19d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47529
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change drops the inclusion of entry16.ld and reset16.ld and
instead adds the content of those files directly in memlayout_x86.ld
in amd/picasso. This is done to allow the work for top-aligning
bootblock to happen independent of Picasso layout. Once that is
complete, Picasso layout can be re-evaluated to see if it can make use
of the common bootblock linker file includes.
TEST=Verified that coreboot.rom generated using --timeless is the same
with and without this change for trembyle.
Change-Id: Ib1218b24a06d0f69b856fb21458a6183fd21fcbc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
In the file uintptr_t that is defined in stdint.h and struct device that
is defined in device/device.h are used, so include them directly to
avoid having to rely on them being included in the file that includes
this header file.
Change-Id: I9893619924d45e5690a5cfc65252ace4cb7f1486
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Add a NULL check and only skip setting the default operations
if `.ops` was set by a driver. It's fairly unlikely that some-
body adds a driver and forgets the `.ops` pointer. So this is
mostly to increase readability: Nobody should have to wonder
if we're missing a NULL-check.
The condition is moved out of the loop to reduce indentation
levels. Alternatively, we could jusk skip drivers that don't
have `.ops` set (i.e. continue the loop).
Change-Id: I5dcc05ebb092fb9c4be929c81ea2b05a10b1311b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46297
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Devices of class type "system" are arbitrary devices and it's not clear
which of them need bus mastering. Therefore, enable bus mastering
conditionally based on Kconfig option PCI_ALLOW_BUS_MASTER_ANY_DEVICE.
Change-Id: Ia04e83606a0a081c0758ec59e52627aa1dbd2622
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
If the stub size would be larger than the save state size, the stagger
points would overlap with the stub.
The check is placed in the stub placement code. The stub placement
code is called twice. Once for the initial SMM relocatation and for
the permanent handler in TSEG. So the check is done twice, which is
not really needed.
Change-Id: I253e1a7112cd8f7496cb1a826311f4dd5ccfc73a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47069
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The only reason to write the MR values to the training result registers
is for EV (Electrical Validation) usage. The hardware doesn't need it.
Tested on Asus P8H61-M PRO, still boots.
Change-Id: I808174494729453f4ebcaa13258d735faae68d72
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
It is usually written to right after programming a pattern, because its
lower byte contains the number of cachelines of the programmed pattern.
The other cases merely reset the WDB data write and compare pointers.
Change-Id: I97196d404bf70542db28499e0d2e24b7cdab07b6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Create the lantis variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171546871
BRANCH=dedede
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_LANTIS
Change-Id: Ie3d15a687b870afc7d8bbeb6b5cab0792650da31
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Add a function that initializes GPIOs based on the sleep type that
the system is coming back from. This allows initialization of the
fingerprint GPIOs which need to be handled differently between wake
from S3 and boot from S5.
On initial boot, the state of the FP sensor could be either
enabled or disabled. Because of this, on boot, we power off
the sensor for >200ms, to reset its state, then power it back on.
In suspend/resume, the fingerprint sensor should remain powered
the entire time.
If fingerprint is disabled on the trembyle-based board, set the pins
to no-connect. Dalboz doesn't have fingerprint and the GPIOS are
configured differently due to the FT5 chip having fewer GPIOS than
FP5, so nothing needs to be initialized there.
There were also a couple of trivial comment clean ups regarding the
FPMCU GPIOS.
BUG=b:171837716
TEST=Boot & Check GPIO states.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I16a2e621145782e0a908bb3e49478586c09a0e0a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
