Allow EC region to be readable by BIOS/CPU so that flashrom
can read it.
BUG=b:123199222
TEST=Build coreboot with CONFIG_LOCK_MANAGEMENT_ENGINE set,
run firmware_LockedME test.
Change-Id: I306c74a0893355e57632a22a712b1f4fdaa19306
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change bumps up the BIOS region to 28MiB to use the hole
between SI_ALL and SI_BIOS. Since this SPI flash part is 32MiB, only
the top 16MiB actually gets memory mapped. Thus, the change ensures
that only RW_LEGACY lies in the 12MiB that is not memory mapped.
BUG=b:123443737
TEST=Verified that hatch still boots up. Ensured that fmap dump looks
correct.
Change-Id: I5832d2b89c7eedfc270755e2add16131cfbddff4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Set SerialIoDebugUartNumber to CONFIG_UART_FOR_CONSOLE
SerialIoDebugUartNumber UPD use to select UART Number for Debug Purpose
The default value of SerialIoDebugUartNumber is 2 by default it selects UART 2
so it needs to be initialized as per board config
BUG=b:123702398
Change-Id: I91df4bb756e8ea86db112f1cc28687f48b2c0525
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31375
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Sarien board may have different touchscreen devices that use the
same I2C slave address but have different requirements such as needing
a special driver or ACPI configuration.
In order to support this the devicetree may be configured with multiple
devices at the same address and at boot time the unused devices will be
disabled.
Because there is no GPIO for selecting the device that is present it can
instead be selected with Kconfig, or by setting a VPD key to the HID of
the touchscreen device that is present. The default for Sarien devices
is to not enable a touchscreen for the OS.
The touchscreen selection is currently limited to the Sarien variant but
this also adds the touchscreen HID for Arcada to Kconfig so it would not
complain about the key not being set.
BUG=b:122019253
TEST=This was tested on a Sarien board by adding a second entry to the
devicetree at the same address. Without this change the SSDT is not
loaded by the kernel because of the address conflict. After this change
no touchscreen is enabled by default, but one can be selected with
Kconfig or by setting the 'touchscreen_hid' VPD key.
Change-Id: I4da12b1de0c551bcd89325fe0d8c66c6ffeb7afc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Under some scenarios the key ladder on the Cr50 can get disabled. If
this state is detected, trigger a reboot of the Cr50 to restore full
TPM functionality.
BUG=b:121463033
BRANCH=none
TEST=Built coreboot on sarien and grunt platforms.
TEST=Ran 'gsctool -a -m disable' and reboot. Verified coreboot sends
VENDOR_CC_IMMEDIATE_RESET command to Cr50 and that the Cr50 resets and
then the platform boots normally.
TEST=Performed Cr50 rollback to 0.0.22 which does not support the
VENDOR_CC_TPM_MODE command, confirmed that platform boots normally and
the coreboot log captures the unsupported command.
Tested-by: Keith Short <keithshort@chromium.org>
Change-Id: I70e012efaf1079d43890e909bc6b5015bef6835a
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This implementation configures GPIO (GPP_A21, GPP_C21, GPP_D16)
pad in non-inversion mode i.e Rx PAD state is not inverted as
it is sent from GPIO to IOAPIC.
BUG=b:123315212
TEST=Tested for below:
-> Verify touchpad is working fine.
-> TPM init is successful and boot with fixed boot media.
Change-Id: I6034fd07ccc96a19218d57ef8bb9049c4b963ea5
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/31328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
`off_t` is supposed to be signed, but has no (minimum) width
specified. We'll assume 32-bit minimum, like a `signed long int`.
Also include `sys/types.h` in `libpayload.h` so everything is
available through the latter.
Change-Id: I6c0c1bc1a959db7863cbad2ba29318da162431be
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/31346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
* Adding separate targets for 32bit and 64bit qemu
* Using the riscv64 toolchain for 32bit builds requires setting -m elf32lriscv
* rv32/rv64 is currently configured with ARCH_RISCV_RV32/RV64 and not per stage.
This should probably be changed later.
TEST=Boots to "Payload not loaded." on 32bit qemu using the following commands:
util/riscv/make-spike-elf.sh build/coreboot.rom build/coreboot.elf
qemu-system-riscv32 -M virt -m 1024M -nographic -kernel build/coreboot.elf
Change-Id: I35e59b459d1770df10b51fe9e77dcc474d7c75a0
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/c/31253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: ron minnich <rminnich@gmail.com>
This macro was unnecessarily complex. Trying to avoid an overflow
for unknown reasons, and instead shifted the result into the sign
bit in C. Using a plain number literal that forces C to use an
adequate integer type seems to be safe. We start with 0xffffffff,
subtract `x` and add 1 again. Turned out to be a common pattern
and can't overflow for any positive 32-bit `x`.
Change-Id: Ibb0c5b88a6e42d3ef2990196a5b99ace90ea8ee8
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/31322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
It needs to tune usb2eye setting for these ports:
USB2[4] - type-c port
USB2[6] - camera
BUG=b:122878632
BRANCH=octopus
TEST=built and passed usb2eye SI test
Change-Id: Iaa3adaab2f391e95730b141dc0237ca62c459e5a
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31359
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The CAR setup is almost identical to the cpu/intel/non-evict
CAR setup, with the only difference that L2 cache needs to be
separately enabled. Currently this assumes that it is possible
to use a static Kconfig option to cover all CPU's requiring this.
Change-Id: Iae9b584bc0d32a56be2e6e2b2e893897eb448aa5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
On my Thinkpad T420 the default 3000ms SeaBIOS timeout is too short,
it takes nearly 5000ms for my keyboard to become ready.
Timing out before it's ready leads to pretty bad behavior: I cannot use
my keyboard at all to control SeaBIOS, nor the subsequent GRUB instance.
Linux is fine though, possibly because it does its own keyboard init.
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Change-Id: Id1681bf3921c8b5dc124d4c4e9072f146f84f3a2
Reviewed-on: https://review.coreboot.org/c/31279
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It is not mentioned in the FSP spec and doesn't seem to be implemented
for any other FSP than the Broadwell-DE one.
Change-Id: I87c758204f1aabf13f47de19fd87c6e1ed67258e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/31300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use AGPIO 10 as the EC sync interrupt for MKBP events for sensor data.
On this platform, interrupts are routed via the GPIO controller so need to be
registered using GpioInt instead of Interrupt.
BUG=b:123750725
BRANCH=grunt
TEST=MKBP events still received (with matching EC and kernel changes)
Change-Id: If499d24511bbaa7054207b7e0b98445723332c4f
Signed-off-by: Edward Hill <ecgh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
I think our docs inside of the codebase might not be the ideal place
to announce future events.
First, they might be scheduled so shortly before the conference that the
change, if at all done, would barely make it to the repo and the web. Also,
_if_ really maintained, it would churn the docs unnessesarily. But, I doubt
that anyone of us would want to maintain this here at all. Lastly, I think
that nobody out there would _look for_ upcoming events in coreboot's
documentation. We have bigger problems in the Documentation directory than
this :)
Change-Id: I918e17a427405a05722c6e0d61dc422f94cac809
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-on: https://review.coreboot.org/c/31266
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add Philipps great 35c3 talk and Davids and Andreas fosdem talk to the
conferences page. linuxboot adds those to their website too but they
can't be linked to too often :)
Change-Id: I1e7ce078020dc5e9c9d9d47210c70ee16ef2f82e
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-on: https://review.coreboot.org/c/31265
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
