There is no public datasheet available for this SuperIO so the resources are
guessed by looking at other ITE SuperIO's and the register dumps while running
vendor firmware.
The only board with this SuperIO in the tree is the asus m5a88-v. Most of the
devicetree entries would have been invalid here so one should not worry too much
about regressions.
Tested with Foxconn d41s.
Change-Id: I6715c68b3aa9aebf6e292975cbf64ce905b30e8b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The existing code for modifying the power state after power loss of the system
only implemented the transitions from power off to either power on or power keep
properly.
Since I don't have a board with this chip, I couldn't test the patch on real
hardware. The two cases described above were tested before the original patch
was merged, so I'd expect this to work.
Change-Id: I3c26a2837e451dbfd3cee82e9beedc0f4a90af03
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
The implementation of wpcd376i in coreboot is based on the
superiotool output which apparently was incorrect. This
patch refines the implementation to match the datasheet.
Change-Id: I0108e912dc4f603276074f0999c6d3146c3b13f9
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/27857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
By defining SUPERIO_KBC_PS2M, ACPI code is added to show the PS/2 mouse.
This has been tested on an ASUS P8H61-M LX with Linux 4.9.110 and
4.17.8. In each case, the PS/2 mouse works automatically, whereas it was
not detected before.
Change-Id: I7983f85b3fd23547950f1f75a81bbca63c63d52b
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/27797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
When compiling for the ASUS P8H61-M LX, IASL 20180531 emits the
following remark: "Control Method should be made Serialized (due to
creation of named objects within)". Making the appropriate methods
Serialized eliminates these remarks.
Change-Id: I8e95d9a00a629a2f904c79b78fac20810327ed37
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/27796
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Exposing the parallel port via ACPI causes Linux to automatically detect
the parallel port and load the appropriate modules. Tested on an ASUS
P8H61-M LX with Linux 4.9.110 and 4.17.8.
However, no parallel port device has been tested.
Change-Id: I2529a074e24433d093ad0650a45c7b29238620f3
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/27795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch makes it possible to enter the config mode of the super IO chip, so
that changes can be made to the configuration registers.
Change-Id: I7e31eaf217b3af2226c1e7d2f14f2ef7b0d7ddbe
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
The pnp ops struct is already passed to the pnp_enable_devices function and it
is used if no override is supplied in the elements of the pnp_info struct array
Change-Id: I14dbeda9832a25116cf53c36197615e9d02d5134
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The pnp ops struct is already passed to the pnp_enable_devices function and it
is used if no override is supplied in the elements of the pnp_info struct array
Change-Id: I42469c844074db57071d0191d12d8fd64f462672
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The pnp ops struct is already passed to the pnp_enable_devices function and it
is used if no override is supplied in the elements of the pnp_info struct array
Change-Id: I5bd525532c01b3b9f7ddbc8eab42caa8b7f30795
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The pnp ops struct is already passed to the pnp_enable_devices function and it
is used if no override is supplied in the elements of the pnp_info struct array
Change-Id: Ic6387032e043b6ad9e9ceefd2fcc1cdf843e2989
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Configure SuperIO on shutdown to keep devices enabled, set green LED
to fading on sleep and normal on wake.
Add SSDT to write LDN4 IOBASE addresses stored in devicetree.cb.
Tested on HP8200:
* Wakes from power button or USB keyboard.
* LED is fading
Change-Id: I2035249a39616aa2d87bd93f9e49c70d231546cc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Pass the address of the chip-specific ops struct instead of the one of
the generic pnp_ops struct to the PNP device enable function.
This allows the removal of the LDN-specific ops overrides which is also done in
this patch.
Change-Id: I0c820254e97e3f80470d148552af06940e147b74
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/23008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Pass the address of the chip-specific ops struct instead of the one of the
generic pnp_ops struct to the PNP device enable function.
This allows the removal of the LDN-specific ops overrides which is also done in
this patch.
Change-Id: I16e485494e448ae02e0a7b9e21b90ddbb1a53a4b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/23007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Pass the address of the chip-specific ops struct instead of the one of the
generic pnp_ops struct to the PNP device enable function.
This allows the removal of the LDN-specific ops overrides which is also done in
this patch.
Change-Id: I5f03a4064778c419f4b9c50e70db1296addf6c9e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/23006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Implement method to access the SuperIO's harware monitor (HWM) IO space.
Set the PSU fan using a new CMOS option psu_fan_lvl. Add the CMOS option
to all board that use NPCD378. In case no CMOS is set use the default
fan level 3.
The HWM space can be written to at any time, but the SuperIO has to be
notified that a write is ongoing. After clearing the write-lock bit all
changes are applied at once.
Tested on HP Compaq 8200 SFF.
Change-Id: I56ce7ad1df88638589a577b8a09d5d775557887b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/26050
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Program the Super I/O to turn the machine on or restore its power state
when AC power is restored.
Based on code from src/superio/nuvoton/nct5572d/superio.c.
Change-Id: I1f3432f43b0784c3696bf1d7233b83d3a203af20
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/25463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The NPCD378 can be found on at least:
* HP Compaq 8200
* HP Compaq 8300
The datasheet is not publicly available, as HP implements lots of
custom hardware. Add basic support for it, based on HP Compaq 8200.
The first eight LDNs seem to be standard nuvoton compatible, except for
LDN4, which is used to control front LED and power in ACPI S3.
LDN8 provides access to HP's proprietary HWM which is accessiable at the LDN's
IOBASE with a size of 0x100 bytes.
The HWM consists of 16 pages with each holding 0xff bytes. The pages can be
selected by writing the page index to IOBASE + 0xff.
TODO:
Reverse engineer the HWM to support fan control.
WARNING:
The remaining LDNs have been guessed and might be wrong!
The serial has been tested and is working.
Change-Id: Ib497fd41b88e9c159eeeffa69bc2bfdccee9cb38
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/25384
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Copies the common/env_ctrl support code from the it8728f driver.
Tested on an ASUS AM1I-A using Linux 4.16.7-gentoo as payload,
and booting userspace without a kexec call.
Prior to this change, an error was given during boot:
it87 it87.656: Detected broken BIOS defaults, disabling PWM interface
After this change, the message is gone, and PWM fan control works
through the /sys/class/hwmon interface.
Change-Id: Id97c4ec19562e7c78308c5afe6ff7c938922c9e7
Signed-off-by: Kevin Cody-Little <kcodyjr@gmail.com>
Reviewed-on: https://review.coreboot.org/26224
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add device tree options to enable beeps when exceeding temperature,
voltage, and fan limits. As of this commit, setting voltage and fan
limits is not implemented.
Change-Id: I57ce622ee4498b75f00e678c2e6d72e499925bce
Signed-off-by: Vagiz Trakhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/22141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
northbridge/intel/i3100
southbridge/intel/i3100
superio/intel/i3100
cpu/intel/socket_mPGA479M
Mainboards:
mainboard/intel/truxton
mainboard/intel/mtarvon
mainboard/intel/truxton
Change-Id: Ic2bbdc8ceb3ba0359c120cf4286b0c5b7dc653bb
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This patch makes it possible to set the "Temperature Sensor Type Register"
at index 6Bh from the devicetree, allowing the use of thermistors instead of
BJT type sensors.
Register documentation (from page 60 of the F71869 datasheet):
6.6.25 Temperature Sensor Type Register - Index 6Bh
Bit 7-4: reserved
Bit 3: T3_MODE (0: thermistor, 1: BJT [default])
Bit 2: T2_MODE (0: thermistor, 1: BJT [default])
Bit 1: T1_MODE (0: thermistor, 1: BJT [default])
Bit 0: reserved
Change-Id: I6af0d93061ec49aec7a9181cdf7affd60fbdca73
Signed-off-by: Renze Nicolai <renze@rnplus.nl>
Reviewed-on: https://review.coreboot.org/22935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Currently, having a keyboard connected to the PS/2 controller of the
ASRock E350M1, after suspending and resuming the system, the keyboard
does not work anymore. A similar problem is documented in commit
448e3863 (drivers/pc80: Add PS/2 mouse presence detect) [1].
There is no reason to not disable the controller during resume. Also,
that way, the PS2 ASL method does not need to be overriden.
[1] https://review.coreboot.org/13165
TEST=Resume system, and notice PS/2 keyboard works.
Change-Id: I51dc446861120f80bc9ffc4cc54b86e317d99689
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/22287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
These macros, broken since day one, should CreateByteField instead
of CreateWordField. Without the fix, any ASLs that try to use it
will fail to compile with a "ResourceTag smaller than Field"
warning.
Change-Id: Ieeb509aece8836785998b23fdc805a747d40a77a
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/22066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Instead of setting "peci_tmpin" in the devicetree, THERMAL_PECI is now
a mode of TMPIN like THERMAL_RESISTOR and THERMAL_DIODE. Since the logic
to set temperature offsets and limits is in the function that sets
thermal modes, it makes sense to treat PECI as yet another mode.
As of this commit, there are no boards that actually use peci_tmpin from
ite/common. There are three boards that have a similar device tree
option, but those boards use it8772f, which implements all superio
functions on its own.
The first user will probably be Gigabyte GA-Z77-DS3H.
Change-Id: I39da50c124ad767f8681302733cf004622975e81
Signed-off-by: Vagiz Trakhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/22076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add devicetree options to set temperature limits that are used to alarm
user when temperature exceeds defined values.
Audio alerts by superio are not implemented yet, but since limits are
visible to userland, some software might use them as is. For instance,
lm-sensors displays "ALERT" when temperature exceeds limits.
Change-Id: I56e041fb78f518d6a9640dc2b3985459991242b9
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Once w83627hf_set_clksel_48() is unified into
winbond/common/early_init.c by /c/21331 (Unify w*_set_clksel_48()),
this file is no longer needed and can be dropped.
Build tested on select affected mainboards.
Change-Id: I6a5e27fdd48c6e002c3a39dc92fef77e85aea209
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This function is identical throughout all Winbond superios in
the tree, so move it into superio/winbond/common/early_init.c,
renamed from early_serial.c because it now does more than just
early serial.
Change all affected mainboards to use the unified function.
Change-Id: If05e0db93375641917e538d83aacd1b50fbd033b
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
