The PCIe WWAN module used on rex requires control over 4 signals to
successfully power it on. It is desirable to do this before passing
control to the payload, because the modem requires a ~10 seconds
initialization phase before it can be used.
The corrected sequence looks like:
1) Drive device into full reset and enable power in bootblock
2) Deassert FCPO in romstage, after power rails stabilize
3) Deassert WWAN_RST#, then WWAN_PERST# in ramstage
BUG=b:244077118
TEST=FM350 could be enumerated via lspci
Measured signals to check start-up Timing Sequence, tpr/ton1/ton2.
Tpr = 572mS
Ton1 = 6.3s
Ton2 = 6.3+4.17ms
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: I6cda9348ef7f54efe5ba2358040596a1c2da1b13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67332
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the missing spaces to two log message, like the one below.
WARNING: Device PCI: 03:00.0 requests a BAR with34 bits of address space, which coreboot is notconfigured to hand out, truncating to 29 bits
Change-Id: If933d8fb0db5b58ff12f043cc73172a3f6ffc624
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Missing power limit setting for Alder-Lake-N 7W soc.
Document reference: 645548 and 646929
BUG=b:245440443
BRANCH=None
TEST=Build FW and test on nivviks board and there is no error
message "unknown SA ID: 0x4617, skipped power limits configuration."
Signed-off-by: Simon Yang <simon1.yang@intel.com>
Change-Id: Iefe17f5b574cc319fe9aad3850401a8aa8e31270
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Change the name of the CALIBRATION_REGION definitions used in two
separate locations. This conflict was causing an error for the
lint-001-no-global-config-in-romstage test.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If6734f2a7d9be669586ea350fb9979fcd422b591
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Currently, the "loading FSP-S" timestamp is added in fsp_silicon_init().
However, most Intel platforms actually load FSP-S earlier than this, in
soc_fsp_load(). So the timestamp is added in the wrong place.
Add the timestamp in fsps_load() instead, after the load_done early
return so that it will only be added for the first call.
Before:
949:finished CSE firmware sync 961,833 (17,998)
17:starting LZ4 decompress (ignore for x86) 1,018,328 (56,495)
18:finished LZ4 decompress (ignore for x86) 1,018,797 (469)
30:device enumeration 1,035,096 (16,298)
971:loading FSP-S 1,048,082 (12,986)
954:calling FspSiliconInit 1,049,331 (1,249)
After:
949:finished CSE firmware sync 959,355 (16,370)
971:loading FSP-S 978,139 (18,784)
17:starting LZ4 decompress (ignore for x86) 1,015,796 (37,656)
18:finished LZ4 decompress (ignore for x86) 1,016,271 (475)
30:device enumeration 1,032,567 (16,295)
954:calling FspSiliconInit 1,046,867 (14,300)
BUG=b:239769975
TEST="loading FSP-S" is added in the right place on nivviks (see above).
Change-Id: Ib26cf96ae97766333fe75ae44381d4f7c6cc7b61
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Having a CSE Lite SKU's firmware is not necessarily depending
on the underlying hardware nor on having ChromeOS installed as
already mentioned in commit f3419b29b7 ("soc/intel/common/cse:
Drop dependency on CHROMEOS for SOC_INTEL_CSE_LITE_SKU").
For example RVP Boards sometimes have a CSE LITE FW, if Chrome board
related stuff is tested, which doesn't necessarily imply a ChromeOS
being used. It is therefore changed to an option, which can be
changed in menuconfig.
Change-Id: I4da7feab881ae43528c9d852cc842ac93fa9c6de
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67078
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Comparing the APOB in RAM to flash takes a significant amount of time
(~11ms). Instead of comparing the entire APOB, use a fast hash function
and compare just that. Reading, hashing, and comparing the hash take
~70 microseconds.
BUG=b:193557430
TEST=compile and boot to OS in chausie with and without this option set
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I241968b115aaf41af63445410660bdd5199ceaba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
dptc_enable is being treated as a bool, so convert to explicitly be a
bool.
BRANCH=none
BUG=b:217911928
TEST=Build zork
TEST=Build guybrush
TEST=Build skyrim
Change-Id: I0e93d892b3b8016221812c8b9ec6c257dcf13ef5
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67188
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Due to layout restrictions on mc_ehl2, the SD-card interface is limited
to operate in DDR50 mode. The alternative modes SDR104 and SDR50 are not
supported. Limit the capabilities in the SD card controller to DDR50
mode only so that the SD card driver in OS will choose the right mode
for operation even if the attached SD card supports higher modes.
Change-Id: Idc7f1466ec71f4218f6b957cadeeffadd069eb2d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Since the latest redesign a new RTC was introduced on mc_ehl2. Instead
of the old RX6110SA the new Micro Crystal RTC RV3028 is used now. Since
the address of this new RTC conflicts with an EEPROM on I2C bus 2, the
new RTC was moved to I2C bus 1.
As the mainboard is not finished yet, there are no incompatibility
issues with this change. Every new mainboard will have the new RTC and
the older mainboards are not delivered yet.
Change-Id: I3dd00855b8c9b22bdea21d3c8563cdb392868751
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
This patch adds a driver for a new RTC from Micro Crystal. Supported
features are:
* configure backup voltage switchover via devicetree
* configure backup capacitor charging mode via devicetree
* set date if a voltage drop on backup voltage was detected
to either a user definable (devicetree) or coreboot build date
Change-Id: I37176ea726e50e4e74d409488981d7618ecff8bb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Some of the pll settings are incorrect, which cause problems in GPU
after booting into kernel.
- MFGPLL opp_ck_en bit isn't located at MFGPLL_CON1, so we need to fix
it to enable MFGPLL properly.
- Switch SPMI clock muxes to 260M to avoid kernel hang while probing
SPMI kernel driver.
TEST=GPU bringup correctly.
BUG=b:233720142
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Change-Id: I971109a5f72e3307899daaf5a5f26022124b559b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67355
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
The header file `compiler.h` is automatically included in the build by
the top level makefile using the command:
`-include $(src)/commonlib/bsd/include/commonlib/bsd/compiler.h`.
Similar to `config.h`, 'kconfig.h`, and 'rules.h`, this file does not
need to be included manually, so remove it.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I5d3eb3f5e5f940910b2d45e0a2ae508e5ce91609
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
The header file `rules.h` is automatically included in the build by the
top level makefile using the command:
`-include src/soc/intel/common/block/scs/early_mmc.c`.
Similar to `config.h` and 'kconfig.h`, this file does not need to be
included manually, so remove it.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I23a1876b4b671d8565cf9b391d3babf800c074db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67348
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Without these, all SuperSpeed ports are wired to EHCI #2.
"superspeed_capable_ports" and "xhci_switchable_ports" should fit both
CMT and SFF variants, while "xhci_overcurrent_mapping" should be
consistent with the first 4 elements of mainboard_usb_ports[].
With this commit, SuperSpeed devices plugged in SuperSpeed ports are
wired to the XHCI on my own Z220 SFF.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Ifddecfd1d32ed6ab84d7eed8dc2d85d83cbebbcc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67089
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch fixes a hidden issue present inside FSP-S while coreboot
decides to skip performing MP initialization by overriding FSP-S UPDs
as below:
1. CpuMpPpi ------> Passing `NULL` as coreboot assume FSP don't need
to use coreboot wrapper for performing any
operation over APs.
2. SkipMpInit -----> Set `1` to let FSP know that coreboot decided
to skip FSP running CPU feature programming.
Unfortunately, the assumption of coreboot is not aligned with FSP when
it comes to the behaviour of `CpuMpPpi` UPD. FSP assumes ownership of
the APs (Application Processors) upon passing `NULL` pointer to the
`CpuMpPpi` FSP-S UPD.
FSP-S creates its own infrastructure code after seeing the CpuMpPpi
UPD is set to `NULL`. FSP requires the CpuMpPei module, file name `UefiCpuPkg/CpuMpPei/CpuMpPei.c`, function name `InitializeCpuMpWorker`
to perform those additional initialization which is not relevant for
the coreboot upon selecting the SkipMpInit UPD to 1 (a.k.a avoid
running CPU feature programming on APs).
Additionally, FSP-S binary size has increased by ~30KB (irrespective of
being compressed) with the inclusion of the CpuMpPei module, which is
eventually not meaningful for coreboot.
Hence, this patch selects `MP_SERVICES_PPI_V2_NOOP` config
unconditionally to ensure pass a valid pointer to the `CpuMpPpi` UPD
and avoid APs getting hijacked by FSP while coreboot decides to set
SkipMpInit UPD.
Ideally, FSP should have avoided all AP related operations when
coreboot requested FSP to skip MP init by overriding required UPDs.
TEST=Able to drop CpuMpPei Module from FSP and boot to Chrome OS on
Google/Redrix, Kano, Taeko devices with SkipMpInit=1.
Without this patch:
Here is the CPU AP logs coming from the EDK2 (open-source)
[UefiCpuPkg/CpuMpPei/CpuMpPei.c] when coreboot sets `NULL` to the
CpuMpPpi UPD.
[SPEW ] Loading PEIM EDADEB9D-DDBA-48BD-9D22-C1C169C8C5C6
[SPEW ] Loading PEIM at 0x00076F9A000 EntryPoint=0x00076FA24E2
CpuMpPei.efi PROGRESS CODE: V03020002 I0
[SPEW ] Register PPI Notify: F894643D-C449-42D1-8EA8-85BDD8C65BDE
[SPEW ] Notify: PPI Guid: F894643D-C449-42D1-8EA8-85BDD8C65BDE,
Peim notify entry point: 76FA0239
AP Loop Mode is 2
GetMicrocodePatchInfoFromHob: Microcode patch cache HOB is not found.
CPU[0000]: Microcode revision = 00000000, expected = 00000000
[SPEW ] Register PPI Notify: 8F9D4825-797D-48FC-8471-845025792EF6
Does not find any stored CPU BIST information from PPI!
APICID - 0x00000000, BIST - 0x00000000
[SPEW ] Install PPI: 9E9F374B-8F16-4230-9824-5846EE766A97
[SPEW ] Install PPI: 5CB9CB3D-31A4-480C-9498-29D269BACFBA
[SPEW ] Install PPI: EE16160A-E8BE-47A6-820A-C6900DB0250A
PROGRESS CODE: V03020003 I0
With this patch:
No instance of `CpuMpPei` has been found in the AP UART log with FSP
debug enabled.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I8ebe0bcfda513e79e791df7ab54b357aa23d295c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66706
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In order to fix the USB port of type-C dongle has no function after
reboot/shutdown, modify ufp which is in google_chromeec_usb_pd_get_info
from the bit1 of type-c role (PD_CTRL_RESP_ROLE_DATA).
BUG=b:239138412
TEST=Built coreboot image and verified that using this patch can detect
usb drive after reboot.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I73a4a6ec37129388783599125f067068d155d93f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67168
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We currently have two competing mechanisms to limit the placement of
resources:
1. the explicit `.limit` field of a resource, and
2. the IORESOURCE_ABOVE_4G flag.
This makes the resource allocator unnecessarily complex. Ideally, we
would always reduce the `.limit` field if we want to "pin" a specific
resource below 4G. However, as that's not done across the tree yet,
we will use the _absence_ of the IORESOURCE_ABOVE_4G flag as a hint
to implicitly lower the `limit` of a resource. In this patch, this
is done inside the effective_limit() function that hides the flag
from the rest of the allocator.
To automatically place resources above 4G if their limit allows it,
we have to allocate from top down. Hence, we disable the prompt for
RESOURCE_ALLOCATION_TOP_DOWN if resources above 4G are requested.
One implication of the changes is that we act differently when a
cold-plugged device reports a prefetchable resource with 32-bit
limit. Before this change, we would fail to allocate the resource.
After this change, it forces everything on the same root port below
the 4G line.
A possible solution to get completely rid of the IORESOURCE_ABOVE_4G
flag would be rules to place resources of certain devices below 4G.
For instance, the primary VGA device and storage and HID devices
could be made available to a payload that can only address 32 bits.
For now, effective_limit() provides us enough abstraction as if the
`limit` would be the only variable to consider. With this, we get
rid of all the special handling of above 4G resources during phase 2
of the allocator. Which saves us about 20% of the code :D
Change-Id: I4c7fcd1f5146f6cc287bd3aa5582da55bc5d6955
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65413
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `IORESOURCE_ABOVE_4G` flag was only explicitly set for our dummy
device that reserves resources behind a hotplug port. The current re-
source allocator implicitly extends this to all devices below the port,
including real ones. Let's make that explicit, so future changes to the
allocator can't break this rule.
Change-Id: Id4c90b60682cf5c8949cde25362d286625b3e953
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66719
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Add option to resource allocator v4 that restores the top-down
allocation approach at the domain level.
This makes it easier to handle 64-bit resources natively. With
the top-down approach, resources that can be placed either above
or below 4G would be placed above, to save precious space below
the 4G boundary.
Change-Id: Iaf463d3e6b37d52e46761d8e210034fded58a8a4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
For TPM2, vb2api_secdata_firmware_create() is already called from
setup_firmware_space() from _factory_initialize_tpm(). Therefore move
the duplicate call from factory_initialize_tpm() to TPM1's
_factory_initialize_tpm().
Change-Id: I892df65c847e1aeeabef8a7578bec743b639a127
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Intel platforms have soft straps stored in the SI_DESC FMAP section
which can alter boot behavior and may open up a security risk if they
can be modified by an attacker. This patch adds the SI_DESC region to
the list of ranges covered by GSC verification (CONFIG_VBOOT_GSCVD).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0f1b297e207d3c6152bf99ec5a5b0983f01b2d0b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66346
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
