This change uses the following information to determine the
appropriate S0ix states to enable as per PDG document: 607872
for TGL UP3 UP Rev2p2 (section 10.13):
1. SoC - UP3 v/s UP4
2. H/W design - external phy gating, external clk gating, external bypass
3. Devices enabled at runtime - CNVi, ISH
In some cases, it is recommended to use a shallower state for
S0ix even if the higher state can be achieved (e.g. with external
gating not enabled). This recommendation is because the shallower
state is determined to provide better power savings as per the
above document. Deepest state expected on tigerlake up3 based
platforms is S0i3.2.
BUG=b:177821896
TEST=Build coreboot for volteer. Verify that deepest
S0ix substate that is enabled is S0i3.1
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Change-Id: I5f2ac8b72d0c9b05bc02c092188d0c742cc83af9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49766
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As a requirement of TCSS this setting needs to be correctly set
to determine what Type-C ports are enabled on the platform. Without
this value correctly set there can be adverse effects on the other
TCSS specific values.
BUG=b:159151238
BRANCH=firmware-volteer-13672.B
TEST=Built image for Voxel and verified that S0ix cycles no longer
fail when the IomPortPad is set to 0
Change-Id: I6c5260cda71041439fe89d15bd3cafd4052ef1e7
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
This change lets IOM consider all USB connected devices as device
attached(DA) scenario. While connecting a typec-to-a dongle, IOM would
disable TC cold and help to resolve enemuration failure after usb3
device is plugged into the dongle.
BUG=b:173054070
TEST=Build and boot on delbin.
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I0ad0322693b4f8fbf1000b24eb21dddcebec686b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49244
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: John Zhao <john.zhao@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
USB3 is in CPU and USB2 in PCH on Tigerlake. Cross die messaging is
implemented between CPU and PCH through the IOSF SB bridge. a PCH xHCI
USB2 port reset event issued by the xHCI driver shall trigger a message
upstream to CPU to wake it from the low power state which allows a USB3
device that downgraded to USB2 to upgrade back to USB3.
BUG=b:176575892
TEST=Built and booted to kernel on Voxel board.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I672f30a117980bc10bd71e9b77c5fa76286b9f5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49052
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Expose a config option that allows enabling the FSP UPD which controls
Precision Time Measurement for a particular PCIe root port.
This UPD is enabled by default in FSP but interferes with achieving
deeper S0ix substates so in order to prevent it from needing to be
explicitly disabled for every root port this change makes disabling it
the default and allows it to be enabled if needed.
BUG=b:160996445
TEST=boot on volteer with PTM disabled by default for all root ports
and ensure S0i3.2 substate can be achieved.
Change-Id: Icb51b256eb581d942b2d30fcabfae52fa90e48d4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46856
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order for USB Type-C idisplays to be detected prior to loading Kernel
PMC IPC driver is needed to communicate with PMC in order to correctly set
the USB Mux settings. This patch is adding in support for early detection
of both Displays.
BUG=b:151731851
BRANCH=NONE
TEST=built and verified that TCSS MUX is being set on Volteer
Change-Id: I58e66f21210d565fb8145d140d2fc7febecdd21a
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42079
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disable C1 C-state auto demotion to decrease SoC power usage.
When set, processor will conditionally demote C3/C6/C7 requests
to C1 based on uncore auto-demote information.
BUG=b:161215906
TEST=Measure and confirm SoC power usage reduction for key use cases
eg 'Google Meets video call'
Measured on instrumented boards for Volteer EVT and Delbin.
Below measurements for Volteer:
Google meets with 720p w/ auto-demotion w/o auto-demotion
System Power 13.14W 9.4W
SOC Power 7.9W 5.4W
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Signed-off-by: Shweta Malik <shweta.malik@intel.com>
Change-Id: I649cafbaf03917d76521aa5f76ec58d218e1a1b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Expose the following FSP UPD interface into coreboot:
- AcousticNoiseMitigation
- FastPkgCRampDisable
- SlowSlewRateFor
BUG=b:153015585
BRANCH=none
TEST= Measure the change in noise level by changing the UPD values.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I1924a3bac8beb16a9d841891696f9a3dea0d425f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45052
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change adds configuration support for both of CnviBtCore and
CnviBtAudioOffload.
BUG=b:169045123
TEST=Built and boot up to kernel on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Id4bf41f07c4a53de17e9eb91a8ddfb1083cbf83e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45585
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Naveen M <naveen.m@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fsp configures the USB over-current pin and overrides the according pad
configuration to NF1, regardless of the port being configured as disabled.
Thus, set the OC pin to 0xff ("disabled") in this case to prevent this.
This allows us to skip setting USBx_PORT_EMPTY in the devicetree for
disabled USB ports.
Change-Id: Ib8ea2ea26c0623d4db910e487b37255e907b299d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45112
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP default UPD for SkipMpInit is set to 0 which refers to run CPU
feature programming on all cores (BSP + APs).
Setting SkipMpInit=1 is not recommended as it will only limit CPU
feature programming on BSP.
TEST=Able to perform CPU feature programming by FSP on all cores
using external MP PPI services.
Change-Id: I22e70f5f15e53c5fabd78cc3698c4d718b607af6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Update configuration for both of TCSS D3Hot and D3Cold. It is expected
D3Hot is enabled for all platforms. Because there are known limitations
for D3Cold enabling on pre-QS platform, this change reads cpu id and
disables D3Cold for pre-QS platform. For QS platform, D3Cold is
configured to be enabled.
BUG=None
TEST=Verified D3Hot is enabled, D3Cold is disabled for pre-QS (cpu:806c0)
and enabled for QS (cpu:0x806c1).
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I534ddfefcd182f5b35aa5e8b461f0920d375a66d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43980
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Divya S Sasidharan <divya.s.sasidharan@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Simplify if-statements and use is_dev_enabled() where possible.
Change-Id: I791273e5dd633cd1d6218b322106e2f62a393259
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43897
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BOOL type Kconfig values should be used through the CONFIG() macro.
These instances were not, so update them.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ie4706d82c12c487607bbf5ad8059922e0e586858
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
SataPortsEnableDitoConfig Enable DEVSLP Idle Timeout settings DmVal and
DitoVal. SataPortsDmVal and SataPortsDitoVal helps to determine when to
enter Device Sleep. Device Sleep enables the host bus adapter (HBA) to
assert the DEVSLP signal as soon as there are no commands outstanding
to the device and the port specific Device Sleep idle timer has expired.
Device Sleep Idle Timeout values (PxDEVSLP.DITO and PxDEVSLP.DM) are
port specific timeout values used by the HBA for determining when to
assert the DEVSLP signal. They provides a mechanism for the HBA to apply
a programmable amount of hysteresis so as to prevent the HBA from
asserting the DEVSLP signal too quickly which may result in undesirable
latencies. This patch is created based on Intel Tiger Lake Processor
PCH Datasheet with Document number:575857 and Chapter number:12.
* PxDEVSLP.DM -> SataPortsDmVal: Enable SATA Port DmVal DITO multiplier.
Default is 15.
* PxDEVSLP.DITO -> SataPortsDitoVal: Enable SATA Port DmVal DEVSLP Idle Timeout
(DITO), Default is 625ms.
BUG=b:151163106
BRANCH=None
TEST=Build and boot volteer and TGL RVP.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I6a824524738a9e0609f54bea9d892b4a42a1d3db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42214
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A UPD HybridStorageMode allows a platform to dynamically configure the
PCIe strap configuration required if an Optane device is connected.
The strap configuration is done by HECI commands between FSP and CSE to
override the default PCIe strap value, and the updated strap value is
stored in SPI RW data to be used on the next boot.
CSE Lite supports the strap override when running on CSE RW partition,
while CSE RO partition does not support it because CSE RO is not allowed
to access SPI RW data. The strap override failure on CSE RO causes FSP
not initializing PCH Clkreq and PCIe port mapping and this results NVMe
and Optane initialization failure.
By disabling HybridStorageMode in case of CSE RO boot, NVMe detection is
done by the default PCIe configuration and Optane is detected as a
single NVMe storage device on CSE RO boot in recovery mode. Both NVMe
and Optane devices detection as well as OS installation to these storage
devices are verified on CSE RO boot in recovery mode.
BUG=b:158643194
TEST=boot and verified with tglrvp and volteer in recovery mode
Cq-Depend: chrome-internal:3100721
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Change-Id: I5397cfc007069debe3701bf1e38e81bd17a29f0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42282
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This enables Thermal Control Circuit (TCC) activation feature to set
tcc_offset to new value in devicetree.
BUG=None
BRANCH=None
TEST=Built for volteer platform and verified the MSR value.
Change-Id: I36b0d6aad4be8a9cbb145dcd66d65235d3f6ac35
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch adds support for enabling/disabling PCIe hot-plug via
a chip config option PcieRpHotPlug, which is copied to the corresponding
FSP-S UPD.
BUG=b:156879564
BRANCH=none
TEST=Boot Volteer/RVP with FSP log and check hotplug enabled/disabled
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I4c0187644b6ca9735f1b159e110e3466af14ff71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41794
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For Tiger Lake platforms, this patch set provides a way to override PCH
external VR settings and ext rail voltage/current through devicetree.
This enables setting of optimal settings for FIVRs for a particular PCH
type.
BUG=None
BRANCH=None
TEST=Build and boot volteer.
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Ic55472d392f27d153656afbe8692be7e243bb374
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41424
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Connect Topology Command(CNTP) is sent with default timeout value
(0x1388) along with FW CM. The CNTP is supposed to be skipped while
using SW CM. While transition from FW CM to SW CM, the default timeout
value could cause boot time delay up to ~10 seconds. Set this FSPS UPD
ITbtConnectTopologyTimeoutInMs to be 0 in order to avoid the 10 seconds
delay. Future FSP release will evaluate this ITbtConnectTopologyTimeoutInMs
value. While FSP finds this UPD value being 0, FSP will skip sending CNTP.
BUG=b:155893566
TEST=Built image with SW CM Thunderbolt firmware and verified no
outstanding delay time while using FSP v3197 during boot to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I47e3519fd818cb56e6abd16464d8370ffddabc5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42056
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's already disabled by FSP default but disable VMD by devicetree
to remove dependency with FSP default setting.
BUG=None
Branch=None
Test=Build TGLRVP and boot up and check FSP log for checking VMD is
disabled.
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ief81fe481b94abed9754881cf1f454999fafa52e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41061
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds FSP UPD D3HotEnable and D3ColdEnable for configuration.
D3Hot low power mode support is for TCSS xhci, xdci, TBT PCIe root
ports and DMA controllers. D3Cold is lower mode for TBT PCIe root
ports and DMA controllers with D3Hot->D3Cold transition.
BUG=🅱️146624360
TEST=Built and booted on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I6782cde6a1bfe13f46e75db8c85537c6d62f5d41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
In order for the SOC to be able to control the Aux line orientation for
Type-C ports that do not have a retimer, the IomTypeCPortPadCfg UPD needs
to be configurable through devicetree to correctly set the GPIO pins that
the SOC should use to flip orientation.
BUG=b:145220205
BRANCH=NONE
TEST=booted Volteer proto 2 and verified that the AUX channels flip
when the cable is flipped
Change-Id: I2e48adb624c7922170eafb8dfcaed680f008936e
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40244
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP provides the UPD's for SATA and DMI power optimization.
In this patch we are adding the soc's config support to set
those power optimization bits in FSP. By default those
optimizations are enabled. To disable those we need to set
the DmiPwrOptimizeDisable and SataPwrOptimizeDisable to 1
in devicetree.
BUG=b:151162424
BRANCH=None
TEST=Build and boot volteer and TGL RVP.
Change-Id: Iefc5e7e48d69dccae43dc595dff2f824e53f5749
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40005
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This CL adds support to fill PcieRpClkReqDetect UPD from devicetree.
Filling this UPD will allow FSP to enable proper clksrc gpio
configuration.
BUG=None
BRANCH=None
TEST=Build and boot tglrvp.
Change-Id: Iad0ba94fea019623a5b98fff0cb4a2cd1d2a7bd7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Add LTR and AER configuration to the root ports config.
BUG=b:151166040
TEST= build and boot volteer and check LTR and AER value
from FSP log
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I668f2e5fea15019a9e5ae06fb4d55fa2aea69e8a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40262
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I482715c166ccf5d2f3cc25118d25b07dbfd6650a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
New Kconfig for Jasperlake soc was created and fsp_param for Jasperlake
has differences compared to Tigerlake. Thus renaming fsp_params.c to
fsp_params_tgl.c to point out correct file as per soc selected.
Also adding new file for fsp_param_jsl for Jasperlake SoC and currently
its the copy of fsp_param_tgl.
TODO: update files with correct fsp_params
Change-Id: I12815ae28a1eb4c64afda0a85b5c14fc0da3e4b1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37267
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Include soc common lpss header file to resolve build error due to
missing soc_lpss_controllers_list declaration.
Also remove console header since it is unused.
Change-Id: I2b2c82fc7592120993bc483d3061803cf75c7335
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37556
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clone entirely from Icelake
List of changes on top off initial icelake clone
1. Replace "Icelake" with "Tigerlake"
2. Replace "icl" with "tgl"
3. Replace "icp" with "tgp"
4. Rename structure based on Icelake with Tigerlake
5. Remove and clean below files
5.a Clean up upd override in fsp_params.c,
will be added once FSP available.
5.b Remove __weak functions from fsp_params.c
5.c Remove dGPU over PCIE enable Kconfig option
6. Add CPU/PCH/SA EDS document number and chapter number
7. Remove unnecessary headers from .c files based on review
Tiger Lake specific changes will follow in subsequent patches.
1. Include GPIO controller delta over ICL
2. FSP-S related UPD overrides as applicable
Change-Id: Id95e2fa9b7a7c6b3b9233d2c438b25a6c4904bbb
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36087
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
