Always exit 4-byte addressing mode to prevent errors when the spi flash
is not left in 4-byte addressing mode.
TEST=boot with PSP releases that leave the flash in both 4-byte
and 3-byte mode and verify flash writes
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I9884b85bc3b0a9b654a2cb91fb314b0869abd622
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76094
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIO GPP_B5 is used as input on this mainboard. For a full-populated
DRAM configuration, the input signal is connected to ground and for a
half-populated configuration it is connected to 3.3 V.
BUG=none
TEST=Use different HW configurations and check coreboot log
GPP_B5 = 0:
[DEBUG] 2 DIMMs found
GPP_B5 = 1:
[INFO ] meminit_channels: DRAM half-populated
[DEBUG] 1 DIMMs found
Change-Id: I48b4a3bea7f1ff804b78b7c648a7ea1925627b8a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76245
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
There can be mainboard variants, which are only equipped with
half-populated DRAM. For this reason, the meminit parameter for
populatation should be adjustable. The default setting remains at
full-populated DRAM. At mainboard variant level a different selection
via individual input paths can be made.
Change-Id: I390bbfa680b5505bb2230fa0740720bd9dd1fafb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76244
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
At the time of writing SMM runtime does not make register
accesses to LAPIC registers, but such breakage has been
reported.
S3 resume failure, where OS switched back from X2APIC
to XAPIC mode, can be reproduced with a sandybridge SKU
that has VT-d disabled.
Change-Id: I300ba87c3d8fde548dbaf95703bd7e2fe54cff57
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Some ancient CPUs may have had LAPIC disabled at power-up, so
semantically enable_lapic() should always come before attempting
to access the register banks.
With X2APIC_ONLY option it is necessary to ensure enable_lapic()
is called prior to any other lapic register space accesses,
since the XAPIC mode MMIO accessors are optimised away build-time
and CPU's do not yet initialise for X2APIC mode at reset.
Change-Id: I96eaa5c43108c802375e184e0c68b5091ca0198f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76195
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Updating from commit id 8be5a82:
2022-10-04 14:01:00 +0000 - (Fix "unnecessary with of ancestor [-gnatwr]")
to commit id 95ad8c5:
2022-12-22 15:32:38 +0000 - (hw-debug: Place global variables in the .bss section)
This brings in 1 new commits:
95ad8c5 hw-debug: Place global variables in the .bss section
Change-Id: Ib28dbcdf14f313cbfeab03e98e05fffe16a1b708
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75794
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Updating some submodule pointers to their latest commit causes some
builds with default configuration to fail since all required components
don't fit into 2MB anymore. Specifically, this has been experienced with
the microcode and FSP submodules.
So, increase the default CBFS size to 4MB to make sure builds succeed
with updated submodules.
Change-Id: I2fc16240bef36c057608acadf3cb7c65e7f0d244
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
VP2420 (vault_ehl) has only 1 DIMM slot present. Set the DIMM_MAX to 1
to optimize the common libraries to not attempt to read and parse more
SPD than needed.
TEST=Boot Protectli VP2420 (vault_ehl) with different DIMMs and see
FSP is retraining the memory properly and fastboot is working.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I29a99f387ffe2df1060547e0818c5c5b66a27061
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73819
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michał Kopeć <michal.kopec@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CBMEM can contain log in different forms (at most one is present):
- coreboot-specific format (CBMEM_ID_TPM_CB_LOG exported as
LB_TAG_TPM_CB_LOG)
- TPM1.2 format (CBMEM_ID_TCPA_TCG_LOG)
- TPM2 format (CBMEM_ID_TPM2_TCG_LOG)
The last two follow specifications by Trusted Computing Group, but until
now cbmem couldn't print them. These formats were added not so long ago
in:
- commit 4191dbf0c9 ("security/tpm: add TPM log format as per 1.2
spec")
- commit 53db677586 ("security/tpm: add TPM log format as per 2.0
spec")
These changes make cbmem utility check for existence of TPM1.2/TPM2 logs
in CBMEM and add code necessary for parsing and printing of their
entries.
TEST=`cbmem -L` for CONFIG_TPM1=y case
TCPA log:
Specification: 1.21
Platform class: PC Client
TCPA log entry 1:
PCR: 2
Event type: Action
Digest: 5622416ea417186aa1ac32b32c527ac09009fb5e
Event data: FMAP: FMAP
TEST=`cbmem -L` for CONFIG_TPM2=y case
TPM2 log:
Specification: 2.00
Platform class: PC Client
TPM2 log entry 1:
PCR: 2
Event type: Action
Digests:
SHA256: 68d27f08cb261463a6d004524333ac5db1a3c2166721785a6061327b6538657c
Event data: FMAP: FMAP
Change-Id: Ib76dc7dec56dd1789a219539a1ac05a958f47a5c
Ticket: https://ticket.coreboot.org/issues/425
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68749
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch enables BT offload feature for soundwire audio over SSP1.
BT mode is selected via FW_CONFIG and corresponding VGPIOs are
programmed.
BUG=b:275538390
TEST=build and verify BT offload on rex soundwire audio
Change-Id: I99df78787d9f54c91bcedf6f70352890a715cdb3
Signed-off-by: Uday M Bhat <uday.m.bhat@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75924
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Always send the Exit 4-Byte Address Mode (E9h) command before the first
access to the SPI flash in all stages when the SPI flash is
memory-mapped. This is useful for x86 mainboards that do not access SPI
flash in bootblock yet still need to exit 4-byte addressing mode in
romstage or ramstage.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I3a62bfa44a0a5645c1bb80b32d0b9f92075c66bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Replace `CBFS_SIZE` with FMD files to declare regions and sizes. This
will be used to lock BIOS region (except SMMSTORE) on boot.
`CBFS_SIZE` was incorrectly set to 10 MiB, so this also corrects the
BIOS region size to match the FIT values.
Change-Id: I0f068f4d9b376f12b46faa5bb0c6a08e6cb744d8
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76155
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Multiple users have requested to have the DMI values for product UUID
and serial number be populated. Enable the drivers so that we may set
them when flashing or updating firmware.
Change-Id: I710363d9df626d51756a265f0099f26ef28411c2
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
