system76-coreboot/src/mainboard/amd/bilby/mainboard.c

/* SPDX-License-Identifier: GPL-2.0-only */

#include <console/console.h>
#include <device/device.h>
#include <amdblocks/amd_pci_util.h>
#include <FspsUpd.h>
#include <gpio.h>
#include <soc/cpu.h>
#include <soc/southbridge.h>
#include <soc/pci_devs.h>
#include <soc/platform_descriptors.h>
#include <types.h>
#include <commonlib/helpers.h>
#include <soc/amd/picasso/chip.h>
#include "gpio.h"
#include "mainboard.h"

#define MAINBOARD_SHARED_DDI_PORTS 2

/* TODO: recheck IRQ tables */

/*
 * These arrays set up the FCH PCI_INTR registers 0xC00/0xC01.
 * This table is responsible for physically routing the PIC and
 * IOAPIC IRQs to the different PCI devices on the system.  It
 * is read and written via registers 0xC00/0xC01 as an
 * Index/Data pair.  These values are chipset and mainboard
 * dependent and should be updated accordingly.
 */
static uint8_t fch_pic_routing[0x80];
static uint8_t fch_apic_routing[0x80];

_Static_assert(sizeof(fch_pic_routing) == sizeof(fch_apic_routing),
	"PIC and APIC FCH interrupt tables must be the same size");

static const struct fch_irq_routing {
	uint8_t intr_index;
	uint8_t pic_irq_num;
	uint8_t apic_irq_num;
} bilby_fch[] = {
	{ PIRQ_A,	8,		16 },
	{ PIRQ_B,	10,		17 },
	{ PIRQ_C,	11,		18 },
	{ PIRQ_D,	12,		19 },
	{ PIRQ_SCI,	9,		 9 },
	{ PIRQ_SD,	PIRQ_NC,	16 },
	{ PIRQ_SDIO,	PIRQ_NC,	16 },
	{ PIRQ_SATA,	PIRQ_NC,	19 },
	{ PIRQ_EMMC,	PIRQ_NC,	17 },
	{ PIRQ_GPIO,	 7,		 7 },
	{ PIRQ_I2C2,	 6,		 6 },
	{ PIRQ_I2C3,	14,		14 },
	{ PIRQ_UART0,	 4,		 4 },
	{ PIRQ_UART1,	 3,		 3 },
	{ PIRQ_UART2,	 4,		 4 },
	{ PIRQ_UART3,	 3,		 3 },

	/* The MISC registers are not interrupt numbers */
	{ PIRQ_MISC,	0xfa,		0x00 },
	{ PIRQ_MISC0,	0x91,		0x00 },
	{ PIRQ_MISC1,	0x00,		0x00 },
	{ PIRQ_MISC2,	0x00,		0x00 },
};

static void init_tables(void)
{
	const struct fch_irq_routing *entry;
	int i;

	memset(fch_pic_routing, PIRQ_NC, sizeof(fch_pic_routing));
	memset(fch_apic_routing, PIRQ_NC, sizeof(fch_apic_routing));

	for (i = 0; i < ARRAY_SIZE(bilby_fch); i++) {
		entry = bilby_fch + i;
		fch_pic_routing[entry->intr_index] = entry->pic_irq_num;
		fch_apic_routing[entry->intr_index] = entry->apic_irq_num;
	}
}

static void pirq_setup(void)
{
	intr_data_ptr = fch_apic_routing;
	picr_data_ptr = fch_pic_routing;
}

static void program_display_sel_gpios(void)
{
	int idx, port_type;
	gpio_t display_sel[MAINBOARD_SHARED_DDI_PORTS] = {GPIO_29, GPIO_31};

	for (idx = 0; idx < MAINBOARD_SHARED_DDI_PORTS; idx++) {
		port_type = get_ddi_port_conn_type(idx);

		if (port_type == HDMI)
			gpio_output(display_sel[idx], 0);
		else if (port_type == DP)
			gpio_output(display_sel[idx], 1);
	}

}

static void mainboard_init(void *chip_info)
{
	struct soc_amd_picasso_config *cfg = config_of_soc();

	if (!CONFIG(BILBY_LPC))
		cfg->emmc_config.timing = SD_EMMC_EMMC_HS400;

	mainboard_program_gpios();

	program_display_sel_gpios();

	/* Re-muxing LPCCLK0 can hang the system if LPC is in use. */
	if (CONFIG(BILBY_LPC))
		printk(BIOS_INFO, "eMMC not available due to LPC requirement\n");
	else
		mainboard_program_emmc_gpios();
}

static void mainboard_enable(struct device *dev)
{
	init_tables();
	/* Initialize the PIRQ data structures for consumption */
	pirq_setup();
}

struct chip_operations mainboard_ops = {
	.init = mainboard_init,
	.enable_dev = mainboard_enable,
};