MicrocodeDetect function will run by every threads, and it will
use PcdGet to get PcdCpuMicrocodePatchAddress and
PcdCpuMicrocodePatchRegionSize, if change both PCD default to dynamic,
system will in non-deterministic behavior.
By design, UEFI/PI services are single threaded and not re-entrant
so Multi processor code should not use UEFI/PI services. Here, Pcd
protocol/PPI is used to access dynamic PCDs so it would result in
non-deterministic behavior.
This code get PCD value in BSP and save them in CPU_MP_DATA for Ap.
https://bugzilla.tianocore.org/show_bug.cgi?id=726
Cc: Crystal Lee <CrystalLee@ami.com.tw>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
(cherry picked from commit 1e3f7a3782)
Every processor's StartupApSignal is initialized in
MpInitLibInitialize() before calling CollectProcessorCount().
When SortApicId() is called from CollectProcessorCount(), AP Index
is re-assigned by APIC ID. But SortApicId() forgets to set the
correct StartupApSignal when sorting the AP.
The patch fixes this issue.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Chasel Chiu <chasel.chiu@intel.com>
(cherry picked from commit bafa76ef5b)
GetWakeupBuffer() tries to find a below-1M free memory, it checks
whether the memory is allocated already in
CheckOverlapWithAllocatedBuffer(). When there is a memory allocation
hob (base = 0xff_00000000, size = 0x10000000),
CheckOverlapWithAllocateBuffer() truncates the base to 0 which causes
it always returns TRUE so GetWakeupBuffer() fails to find a below-1MB
memory.
The patch fixes this issue by using UINT64 type.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jeff Fan <vanjeff_919@hotmail.com>
(cherry picked from commit 5986cf382e)
Current calculate timeout logic may have overflow if the input
timeout value too large. This patch fix this potential overflow
issue.
V2: Use local variable instead of call GetPerformanceCounterProperties
twice. Also correct some comments.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
(cherry picked from commit 48cfb7c0f4)
PI has description said If an AP is enabled, then the implementation must
guarantee that a complete initialization sequence is performed on the AP,
so the AP is in a state that is compatible with an MP operating system.
Current implementation just set the AP to idle state when enable this AP
which is not follow spec. This patch fix it.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
(cherry picked from commit d5fdae96e2)
If APIC ID values are changed during AP functions execution, we need to update
new APIC ID values in local data structure accordingly.
But if APIC mode change happened during AP function execution, we do not support
APIC ID value changed.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
(cherry picked from commit c6b0feb396)
https://bugzilla.tianocore.org/show_bug.cgi?id=565
Fix NASM compatibility issues with XCODE5 tool chain.
The XCODE5 tool chain for X64 builds using PIE (Position
Independent Executable). For most assembly sources using
PIE mode does not cause any issues.
However, if assembly code is copied to a different address
(such as AP startup code in the MpInitLib), then the
X64 assembly source must be implemented to be compatible
with PIE mode that uses RIP relative addressing.
The specific changes in this patch are:
* Use LEA instruction instead of MOV instruction to lookup
the addresses of functions.
* The assembly function RendezvousFunnelProc() is copied
below 1MB so it can be executed as part of the MpInitLib
AP startup sequence. RendezvousFunnelProc() calls the
external function InitializeFloatingPointUnits(). The
absolute address of InitializeFloatingPointUnits() is
added to the MP_CPU_EXCHANGE_INFO structure that is passed
to RendezvousFunnelProc().
Cc: Andrew Fish <afish@apple.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Andrew Fish <afish@apple.com>
(cherry picked from commit 3b2928b469)
If CR0 PG bit is not set, it means paging is not enabled on BSP. Thus, Execute
Disable feature is not working actually. Thus, we cannot enable it on APs.
v2:
Correct the commit log.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
During switching BSP phase, we need to disable CPU interruput to prevent stack
crashed by Timer interrupt handle. But when we enabled source debugging feature,
debug timer interrupt handler (existing on both PEI and DXE) also could crash
the stack used during switching BSP. So,we need to move save/restore interrupt
to SwitchBSPWorker().
Cc: Feng Tian <feng.tian@intel.com>
Cc: Kinney Michael D <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If APs are waken up by INIT-SIPI-SIPI command, they will lose original local
APIC timer setting. As a result, the timer library instance based on local APIC
timer cannot work on APs function.
This fix is to save BSP's local APIC timer settings before waking up APs and
to sync to APs when APs wakeup by INIT-SIPI-SIPI command.
Setting BSP's current counter to AP's initial counter could make sure BSP and
APs have same counter value across BSP switching.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Kinney Michael D <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The current DxeDebugAgentLib supports source debugging on AP function. This
update is to update DxeMpInitLib to consume Debug Agent Library by
DEBUG_AGENT_INIT_DXE_AP flag. Thus, we could source debugging AP function
invoked by CPU MP Protocol.
However, current SecPeiDebugAgentLib does not support source debugging on AP
function invoked by CPU MP PPI. I have submitted one bugzilla to add this
support at https://bugzilla.tianocore.org/show_bug.cgi?id=308.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Kinney Michael D <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Sometimes a platform knows exactly how many CPUs it has at boot. It should
be able to
- set PcdCpuMaxLogicalProcessorNumber dynamically to this number,
- set PcdCpuApInitTimeOutInMicroSeconds to a very long time (for example
MAX_UINT32, approx. 71 minutes),
- and expect that MpInitLib wait exactly as long as necessary for all APs
to report in.
Other platforms should be able to continue setting a reasonably large
upper bound on supported CPUs, and waiting for a reasonable, fixed amount
of time for all APs to report in.
Add this functionality. The TimedWaitForApFinish() function will return
when all APs have reported in, or the timeout has expired -- whichever
happens first.
(Accessing these PCDs dynamically is safe. The PEI and DXE phase instances
of this library are restricted to PEIM and DXE_DRIVER client modules, thus
the PCD accesses cannot be linked into runtime code.)
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Bugzilla: https://bugzilla.tianocore.org/show_bug.cgi?id=116
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
AP will get target C-State from eax[7:4]. We do shift in ebx firstly before set
to eax. It will lead ebx is incorrect in the next time.
The fix is to set ebx to eax firstly and does shift in eax. Thus, ebx could keep
original value.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
For long mode DXE, we will disable paging on AP to protected mode to execute AP
safe loop code in reserved memory range under 4GB. But we forget to allocate
stack for AP under 4GB and AP still are using original AP stack. If original AP
stack is larger than 4GB, it cannot be used after AP is transferred to protected
mode. Besides MwaitSupport == TRUE, AP stack is still required during phase of
disabling paging in long mode DXE.
Moreover, even though AP stack is always under 4GB (a) in Ia32 DXE and (b) with
this patch, after transferring to protected mode from X64 DXE, AP stack
(in BootServiceData) maybe crashed by OS after Exit Boot Service event.
This fix is to allocate reserved memory range under 4GB together with AP safe
loop code. APs will switch to new stack in safe loop code.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
According to the Intel SDM (325462-060US / September 2016),
> INPUT EAX = 0BH: Returns Extended Topology Information
>
> [...] Software must detect the presence of CPUID leaf 0BH by verifying
> (a) the highest leaf index supported by CPUID is >= 0BH, and
> (b) CPUID.0BH:EBX[15:0] reports a non-zero value. [...]
The "GetApicId" sections in the Ia32 and X64 "MpFuncs.nasm" files do not
perform check (b).
This causes an actual bug in the following OVMF setup:
- Intel W3550 host processor <http://ark.intel.com/products/39720/>,
- the QEMU/KVM guest's VCPU model is set to "host", that is, "the CPU
visible to the guest should be exactly the same as the host CPU".
Under "GetApicId", check (a) passes: the CPUID level of the W3550 is
exactly 11 decimal. However, leaf 11 itself is not supported, therefore
EDX is set to zero:
> If a value entered for CPUID.EAX is less than or equal to the maximum
> input value and the leaf is not supported on that processor then 0 is
> returned in all the registers.
Because we don't check (b), the "GetProcessorNumber" section of the code
is reached with an initial APIC ID of 0 in EDX on all of the APs. Given
that "GetProcessorNumber" searches the
"MP_CPU_EXCHANGE_INFO.CpuInfo[*].InitialApicId" fields for a match, all
APs enter ApWakeupFunction() with an identical "NumApsExecuting"
parameter. This results in unpredictable guest behavior (crashes, reboots,
hangs etc).
Reorganize the "GetApicId" section and add the missing check in both
assembly files.
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
The cached "CPU_INFO_IN_HOB.ApTopOfStack" field currently has type UINT32.
This is not ideal because the AP stacks are located within
"CpuMpData->Buffer", which is allocated with a plain AllocatePages() call
in MpInitLibInitialize():
platform CpuMpPei included PEI RAM > 4GB result
-------- ----------------- ------------- ------
Ia32 * n/a good
Ia32X64 no n/a BAD
Ia32X64 yes n/a good
X64 no * BAD
X64 yes no good
X64 yes yes BAD
- If we are on an Ia32X64 or X64 platform that does not include CpuMpPei,
then CpuDxe cannot reuse the CPU_INFO_IN_HOB structures preallocated by
CpuMpPei (through the CpuInitMpLib GUID HOB), and then AllocatePages()
-- invoked first in 64-bit DXE -- could return an address outside of
32-bit address space.
- If we are on an X64 platform where the permanent PEI RAM extends above
the 32-bit address space, then the same issue can surface even if
CpuMpPei is included: even the original allocation of the
CPU_INFO_IN_HOB structures, by CpuMpPei, could be satisfied from above
4GB.
The original "AP init" branch in "X64/MpFuncs.nasm" correctly considers a
64-bit stack start: the "MP_CPU_EXCHANGE_INFO.StackStart" field has type
UINTN, and the code uses QWORD addition and movement to set RSP from it.
Adapt the "GetApicId" branch of "X64/MpFuncs.nasm":
- change the type of "CPU_INFO_IN_HOB.ApTopOfStack" to UINT64,
- remove the explicit truncation to UINT32 in InitializeApData(),
- update the "GetNextProcNumber" iteration size to the new size of
"CPU_INFO_IN_HOB",
- set RSP with a QWORD movement from "CPU_INFO_IN_HOB.ApTopOfStack".
Because the same CPU_INFO_IN_HOB structure is used by "Ia32/MpFuncs.nasm",
we have to update the "GetNextProcNumber" iteration size there as well.
The ESP setting can be preserved as a DWORD movement from the original
offset (decimal 12), since our integers are little endian.
Cc: Jeff Fan <jeff.fan@intel.com>
Fixes: 845c5be1fd
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
The recent patch "UefiCpuPkg/MpInitLib: Program AP stack in fixed address"
inadvertently broke the first startup of APs during X64 PEI, because in
the TestLock section of the code, it replaced the access to the
NumApsExecuting counter with an access to the unrelated InitFlag field.
Cc: Jeff Fan <jeff.fan@intel.com>
Fixes: 845c5be1fd
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
At this point, ESI still has the value from EBX.
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
When BSP switched, we need to update some AP information. For example,
ApStartupSignalBuffer and ApTopOfStack.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Currently, MpInitLib will program AP stack in dynamic address. Each processor
will calculate its stack address by adding stack size based on the last stack
address. That means AP may have the different stack address everytime it is
wakeup by INIT-SIPI-SIPI.
When all APs have wakeup to execute AP task, each each has been assigned one
stack address. Once the timeout happened on some of APs, BSP will send INIT-
SIPI-SIPI to wake up APs. We need to re-assign stack for APs. Based on the
current implementation, we might assign one stack address used by other APs.
It will cause the unexpected stack overlapped issue.
This fix changed the stack assignment policy. We will record the stack address
assigned to AP at first time AP wakeup. When AP failed on AP task, BSP could
reassigned the same stack for it.
Getting initial APIC ID in assembly code could help AP to get saved its stack
address.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Some CPU information (InitialApicId/ApicId/Health) are duplicated in CPU_AP_DATA
and CPU_INFO_IN_HOB.
This update is to remove the ones from CPU_AP_DATA and update MpInitLib to
consume the ones from CPU_INFO_IN_HOB.
V2:
Fixed potential un-initialized variable issue.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If BSP found APs timeout happened when AP executing AP task, BSP will reset APs
by WakeUpAP(). However, if ApLoopMode is ApMwaitLoop or ApRunLoop, WakeUpAp()
will try to write semaphore in memory to wake up AP. It cannot wake up APs
actually if APs still executing AP task.
This fix is to set ApInitReconfig flag to force BSP to send INIT-SIPI-SIPI to
wake up APs.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Current implementation just allocates reserve memory for AsmRelocateApLoopFunc.
It not be safe because APs will be placed into 32bit protected mode on long mode
DXE. This reserve memory must be located below 4GB memory.
This fix is to allocate < 4GB memory for AsmRelocateApLoopFunc.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
[lersek@redhat.com: strip whitespace at EOL]
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
GetProcessorLocation() is too generic and will conflict with the API defined in
Galileo Board Software Package v1.0.0.
This update is just to rename GetProcessorLocation() to one specific name
GetProcessorLocationByApicId().
Contributed-under: TianoCore Contribution Agreement 1.0
Cc: Leo Duran <leo.duran@amd.com>
Cc: Michael Kinney <Michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <Michael.d.kinney@intel.com>
Reviewed-by: Leo Duran <leo.duran@amd.com>
1) Remove SmmGetProcessorLocation() from PiSmmCpuDxeSmm driver.
2) Remove ExtractProcessorLocation() from MpInitLib library.
3) Add GetProcessorLocation() to BaseXApicLib and BaseXApicX2ApicLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leo Duran <leo.duran@amd.com>
Signed-off-by: Michael Kinney <Michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <Michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
In Exit Boot Services callback function, we cannot use allocate memory services
because it may change the memory map that has been gotten by OS.
This fix is not to allocate reset vector buffer after SaveRestoreFlag is set to
TRUE in MpInitExitBootServicesCallback(). Instead AllocateResetVector() will use
the previous allocated buffer address and save the contents before copying reset
vector code. At the same time, FreeResetVector() will restore original contents
after if SaveRestoreFlag is TRUE.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
