Previous commit fixed that check in DXE, this one now for PEI.
Signed-off-by: Mara Sophie Grosch <littlefox@lf-net.org>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Fix the check for NVMe command set being supported by the controller.
Was problematic with qemu (6.2.0, Debian 1:6.2+dfsg-3), which sets 0xC1
in that register, making the OVMF think the NVMe controller does not
support NVMe.
Uncovered by commit 9dd14fc91c, which
changed the number of bits included in the Css register from 4 to 8.
Signed-off-by: Mara Sophie Grosch <littlefox@lf-net.org>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
No need to check the interface protocol then conditionally setting,
just set it to BOOT_PROTOCOL and check for error.
This is what Linux does for HID devices as some don't follow the USB spec.
One example is the Aspeed BMC HID keyboard device, which adds a massive
boot delay without this patch as it doesn't respond to
'GetProtocolRequest'.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Move the logic that stores starting PCI attributes and sets the
EFI_PCI_IO_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute to
DriverBindingStart() before the memory that backs the
DMA engine is allocated.
This ensures that the DMA-backing memory is not forcibly allocated
below 4G in system address map. Otherwise the allocation fails on
platforms that do not have any memory below the 4G mark and the drive
initialisation fails.
Leave the PCI device enabling attribute logic in NvmeControllerInit()
to ensure that the device is re-enabled on reset in case it was
disabled via PCI attributes.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Leif Lindholm <quic_llindhol@quicinc.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Tomas Pilar <quic_tpilar@quicinc.com>
Acked-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3811
Remove ASSERT() statements that are triggered if a platform provides
an override of PCI ROM attached to a PCI Controller. The PCI Platform
Protocol allows the platform to provide a PCI ROM image for a PCI
Controller. This works for PCI Controllers that do not have an attached
PCI ROM, but the platform is not allowed to replace the PCI ROM for a
PCI Controller that has its own PCI ROM. Removing these ASSERT()
statements enables this additional use case.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
This changes is by adding 50ms delay during voltage switching from 3.3V to
1.8V, plus adding a goto Voltage33Retry for 3.3V checking and retrying.
Change is for Enabling OS boot from SD card through UEFI payload.
Signed-off-by: Aiman Rosli <muhammad.aiman.rosli@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Before trying to access parent root port to check ARI capabilities,
enumerator should see if Endpoint device is not Root Complex integrated
to avoid undefined parent register accesses.
Signed-off-by: Damian Bassa <damian.bassa@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
gcc-11 (fedora 35):
/home/kraxel/projects/edk2/MdeModulePkg/Bus/Usb/UsbBusDxe/UsbBus.c: In function ?UsbIoBulkTransfer?:
/home/kraxel/projects/edk2/MdeModulePkg/Bus/Usb/UsbBusDxe/UsbBus.c:277:12: error: ?UsbHcBulkTransfer? accessing 80 bytes in a region of size 8 [-Werror=stringop-overflow=]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
When use the UsbHcAllocMemFromBlock() and UsbHcFreeMem() to allocate
memory and free memory for the UHC, it should use the corresponding host
address but not the pci bus address.
Signed-off-by: jdzhang <jdzhang@zd-tech.com.cn>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Add correct content to the 'SdDxeExtra.uni' file.
Include 'EmmcDxeExtra.uni' and 'SdDxeExtra.uni' files to their
appropriate INF files.
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=3635
Currently, in order to test the supported attributes,
the PciTestSupportedAttribute() will set the command register
to 0x27 (EFI_PCI_COMMAND_IO_SPACE, EFI_PCI_COMMAND_MEMORY_SPACE,
EFI_PCI_COMMAND_BUS_MASTER, EFI_PCI_COMMAND_VGA_PALETTE_SNOOP) firstly,
and then read back to check whether these attributes are
set successfully in the device.
This will cause the other enabled bits
(other than EFI_PCI_COMMAND_IO_SPACE,EFI_PCI_COMMAND_MEMORY_SPACE,
EFI_PCI_COMMAND_BUS_MASTER,EFI_PCI_COMMAND_VGA_PALETTE_SNOOP)
be cleared for a short of time
This patch fixes this issue by keeping the origina
enabled bits when setting 0x27.
Signed-off-by: xueshengfeng <xueshengfeng@byosoft.com.cn>
Reviewed-by: Ray <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3418
According to xhci spec, at USB packet level, a Control Transfer
consists of multiple transactions partitioned into stages: a
setup stage, an optional data stage, and a terminating status
stage. If Data Stage does not exist, the Transfer Type flag(TRT)
should be No Data Stage.
So if data length equals to 0, TRT is set to 0.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Wenyi Xie <xiewenyi2@huawei.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
The ProcessOptionRomLight() assumes that OpRom has already been
processed in the previous full enumeration and updates
AllOpRomProcessed flag to TRUE by default. However, this may not
be applicable with other pre-stage boot firmwares.
This will update AllOpRomProcessed flag properly by checking
PciRomGetImageMapping().
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=3114
Add logic to flush all UART transmit buffers if there is a
config change from Reset(), SetAttributes() or SetControl().
Use a timeout in the flush operation, so the system can
continue to boot if the transmit buffers can not be
flushed for any reason.
This change prevents lost characters on serial debug logs
and serial consoles when a config change is made. It also
prevents a UART from getting into a bad state or reporting
error status due to characters being transmitted at the same
time registers are updated with new communications settings.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
This simplify ATA driver debugging all ATA packets will be printed to
debug port on DEBUG_VERBOSE level along with the packet execution
status. Additionally failed packets and the failed packet execution
status will be printed on DEBUG_ERROR level.
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3026
This commit adds code to restart the ATA packets that failed due to the
CRC error or other link condition. For sync transfers the code will try
to get the command working for up to 5 times. For async transfers, the
command will be retried until the timeout value timeout specified by the
requester is reached. For sync case the count of 5 retries has been
chosen arbitrarily and if needed can be increased or decreased.
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3024
AHCI driver used to poll D2H register type to determine whether the FIS
has been received. This caused a problem of long timeouts when the link
got a CRC error and the FIS never arrives. To fix this this change
switches AHCI driver to poll the IS register which will signal both the
reception of FIS and the occurrence of error.
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
With some super-speed USB mass storage devices it has been observed
that a USB transaction error may occur when attempting the set the
device address during enumeration.
According the the xHCI specification (section 4.6.5) ...
"A USB Transaction ErrorCompletion Code for an Address Device Command
may be due to a Stall response from a device. Software should issue a
Disable Slot Commandfor the Device Slot then an Enable Slot Command
to recover from this error."
To fix this, retry the device slot initialization if it fails due to a
device error.
Change was verified using a superspeed mass storage device that was
occasionally failing to enumerate in UEFI. With this change this failure
to enumerate was resolved. This failure was also only seen in UEFI and not
in the OS.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3007
Currently UsbDevContext is not cleaned up if USB slot initialization is
failed, the wrong context data will affect next USB devices and
the USB devices can not be enumerated.
Need to disable slot if USB slot initialization is failed.
Below test cases are passed on UpXtreme:
a. USB 3.0 thumb drives can be recognized in UEFI shell
b. SUT can boot to Puppylinux from USB3.0 mass storage,
the storage can be recognized in linux
c. Plug in a USB keyboard (hot plug) and enumeration is OK
in UEFI shell and linux
d. Plug in a USB mouse(hot plug) and enumeration is OK in linux.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Heng Luo <heng.luo@intel.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Add check for NULL HostAddress in AllocateBuffer as required by UEFI
specification.
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
