Previous commit fixed that check in DXE, this one now for PEI.
Signed-off-by: Mara Sophie Grosch <littlefox@lf-net.org>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Fix the check for NVMe command set being supported by the controller.
Was problematic with qemu (6.2.0, Debian 1:6.2+dfsg-3), which sets 0xC1
in that register, making the OVMF think the NVMe controller does not
support NVMe.
Uncovered by commit 9dd14fc91c, which
changed the number of bits included in the Css register from 4 to 8.
Signed-off-by: Mara Sophie Grosch <littlefox@lf-net.org>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Move the logic that stores starting PCI attributes and sets the
EFI_PCI_IO_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute to
DriverBindingStart() before the memory that backs the
DMA engine is allocated.
This ensures that the DMA-backing memory is not forcibly allocated
below 4G in system address map. Otherwise the allocation fails on
platforms that do not have any memory below the 4G mark and the drive
initialisation fails.
Leave the PCI device enabling attribute logic in NvmeControllerInit()
to ensure that the device is re-enabled on reset in case it was
disabled via PCI attributes.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Leif Lindholm <quic_llindhol@quicinc.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Tomas Pilar <quic_tpilar@quicinc.com>
Acked-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3811
Remove ASSERT() statements that are triggered if a platform provides
an override of PCI ROM attached to a PCI Controller. The PCI Platform
Protocol allows the platform to provide a PCI ROM image for a PCI
Controller. This works for PCI Controllers that do not have an attached
PCI ROM, but the platform is not allowed to replace the PCI ROM for a
PCI Controller that has its own PCI ROM. Removing these ASSERT()
statements enables this additional use case.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
This changes is by adding 50ms delay during voltage switching from 3.3V to
1.8V, plus adding a goto Voltage33Retry for 3.3V checking and retrying.
Change is for Enabling OS boot from SD card through UEFI payload.
Signed-off-by: Aiman Rosli <muhammad.aiman.rosli@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Before trying to access parent root port to check ARI capabilities,
enumerator should see if Endpoint device is not Root Complex integrated
to avoid undefined parent register accesses.
Signed-off-by: Damian Bassa <damian.bassa@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
When use the UsbHcAllocMemFromBlock() and UsbHcFreeMem() to allocate
memory and free memory for the UHC, it should use the corresponding host
address but not the pci bus address.
Signed-off-by: jdzhang <jdzhang@zd-tech.com.cn>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=3635
Currently, in order to test the supported attributes,
the PciTestSupportedAttribute() will set the command register
to 0x27 (EFI_PCI_COMMAND_IO_SPACE, EFI_PCI_COMMAND_MEMORY_SPACE,
EFI_PCI_COMMAND_BUS_MASTER, EFI_PCI_COMMAND_VGA_PALETTE_SNOOP) firstly,
and then read back to check whether these attributes are
set successfully in the device.
This will cause the other enabled bits
(other than EFI_PCI_COMMAND_IO_SPACE,EFI_PCI_COMMAND_MEMORY_SPACE,
EFI_PCI_COMMAND_BUS_MASTER,EFI_PCI_COMMAND_VGA_PALETTE_SNOOP)
be cleared for a short of time
This patch fixes this issue by keeping the origina
enabled bits when setting 0x27.
Signed-off-by: xueshengfeng <xueshengfeng@byosoft.com.cn>
Reviewed-by: Ray <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3418
According to xhci spec, at USB packet level, a Control Transfer
consists of multiple transactions partitioned into stages: a
setup stage, an optional data stage, and a terminating status
stage. If Data Stage does not exist, the Transfer Type flag(TRT)
should be No Data Stage.
So if data length equals to 0, TRT is set to 0.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Wenyi Xie <xiewenyi2@huawei.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
The ProcessOptionRomLight() assumes that OpRom has already been
processed in the previous full enumeration and updates
AllOpRomProcessed flag to TRUE by default. However, this may not
be applicable with other pre-stage boot firmwares.
This will update AllOpRomProcessed flag properly by checking
PciRomGetImageMapping().
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=3114
Add logic to flush all UART transmit buffers if there is a
config change from Reset(), SetAttributes() or SetControl().
Use a timeout in the flush operation, so the system can
continue to boot if the transmit buffers can not be
flushed for any reason.
This change prevents lost characters on serial debug logs
and serial consoles when a config change is made. It also
prevents a UART from getting into a bad state or reporting
error status due to characters being transmitted at the same
time registers are updated with new communications settings.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
With some super-speed USB mass storage devices it has been observed
that a USB transaction error may occur when attempting the set the
device address during enumeration.
According the the xHCI specification (section 4.6.5) ...
"A USB Transaction ErrorCompletion Code for an Address Device Command
may be due to a Stall response from a device. Software should issue a
Disable Slot Commandfor the Device Slot then an Enable Slot Command
to recover from this error."
To fix this, retry the device slot initialization if it fails due to a
device error.
Change was verified using a superspeed mass storage device that was
occasionally failing to enumerate in UEFI. With this change this failure
to enumerate was resolved. This failure was also only seen in UEFI and not
in the OS.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3007
Currently UsbDevContext is not cleaned up if USB slot initialization is
failed, the wrong context data will affect next USB devices and
the USB devices can not be enumerated.
Need to disable slot if USB slot initialization is failed.
Below test cases are passed on UpXtreme:
a. USB 3.0 thumb drives can be recognized in UEFI shell
b. SUT can boot to Puppylinux from USB3.0 mass storage,
the storage can be recognized in linux
c. Plug in a USB keyboard (hot plug) and enumeration is OK
in UEFI shell and linux
d. Plug in a USB mouse(hot plug) and enumeration is OK in linux.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Heng Luo <heng.luo@intel.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Add check for NULL HostAddress in AllocateBuffer as required by UEFI
specification.
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
NonDiscoverablePciDeviceDxe currently #defines the module-internal
PCI_MAX_BARS macro, with value 6 (and type "int").
Remove this private macro definition, and adopt PCI_MAX_BAR from
"MdePkg/Include/IndustryStandard/Pci22.h". Both the value and the type
remain unchanged (the standard PCI_MAX_BAR macro expands to 0x0006).
"NonDiscoverablePciDeviceIo.h" gets the definition of PCI_MAX_BAR via its
existent #include <IndustryStandard/Pci.h> directive.
Build-tested only.
Cc: Ard Biesheuvel <ard.biesheuvel@arm.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200409113017.18233-1-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
ASSERT in PollMem_Conf, CopyMem_Conf, SetBarAttributes_Conf
Conformance Test.
SCT Test expect return as Invalid Parameter or Unsupported.
Added Checks for Function Parameters.
return Invalid or Unsupported if Check fails.
Added Checks in PciIoPollIo(), PciIoIoRead()
PciIoIoWrite()
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
SdMmcPciHcDxe driver used to read response only after
command and data transfer completed. According to SDHCI
specification response data is ready after the command
complete status is set by the host controller. Getting
the response data early will help debugging the cases
when command completed but data transfer timed out.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
To allow for easier debug of failing commands we
have added a capability to print TRB and command
packet when we start execution of the TRB(on
DEBUG_VERBOSE level) and when the TRB failed to
execute correctly(on DEBUG_ERROR level). Additionally
we will also print error interrupt status and interrupt
status register on failed SD command.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1989
The commit will avoid unmapping the same resource in error handling logic
for function BuildAdmaDescTable() and SdMmcCreateTrb().
For the error handling in BuildAdmaDescTable():
The error is directly related with the corresponding Map() operation
(mapped address beyond 4G, which is not supported in ADMA), so the Unmap()
operation is done in the error handling logic, and then setting
'Trb->AdmaMap' to NULL to avoid double Unmap.
For the error handling in SdMmcCreateTrb():
The error is not directly related with the corresponding Map() operation,
so the commit will update the code to left SdMmcFreeTrb() for the Unmap
operation to avoid double Unmap.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Changed @rtval to @retval in SdMmcHcStartSdClock
function description.
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
