It is enough to set PxCMD.FRE bit, which cause HBA to post received FISes
into the FIS receive area. According to AHCI Specification, only polling on
PxCMD.FRE to be cleared is necessary, when it is needeed to stop FIS engine
(eg. in order to change PxCMD.FB address).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The Mantis ticket 1353 <https://mantis.uefi.org/mantis/view.php?id=1353>
and Mantis ticket 1472 <https://mantis.uefi.org/mantis/view.php?id=1472>
updated the description of the port multiplier port number parameter in
SATA Device Path Node and ATA Pass-Through Protocol.
Now, this parameter should be set to 0xFFFF instead of 0 to indicate that
an ATA device is directly attached on the controller port.
Please note that this is an incompatible change. The consumer of SATA
device path or ATA_PASS_THRU needs to re-examine its usage to follow UEFI
2.5 mantis 1353 and 1472.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Setting a bit in the PxSACT register for a command in the command list indicates
to the controller that the command list slot contains a native queued command (NCQ).
This can cause problems with some controllers (one such controller is the Marvell 9128).
Since NCQ commands are not used, don't set the PxACT register for commands issued.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Chris Ruffin <chris.ruffin@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16536 6f19259b-4bc3-4df7-8a09-765794883524
Per AHCI 1.1 spec, AE bit of GHC register is read-only if CAP.SAM is 1
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16321 6f19259b-4bc3-4df7-8a09-765794883524
This way is used to avoid that the subsequent operations are treated as failure if the last operation is wrong.
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Sun Rui <rui.sun@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13663 6f19259b-4bc3-4df7-8a09-765794883524
1. move the non-blocking task related setting ahead to store the MapTable and PageCount in case there is a IO operation error happened then the error handler code could use those information to release the resource.
2. Enlarge the TPL protective area to make sure the simulative delay time is accurate when there is mixing usage of Non blocking and blocking I/O.
Signed-off-by: qianouyang
Reviewed-by: erictian
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12712 6f19259b-4bc3-4df7-8a09-765794883524
1. Boost IDE mode boot when slave device is absent.
2. Use D2H FIS to check if the PIO OUT/DMA IN/DMA OUT transfer is finished or error happened. ATA PIO IN has special check as it may just receive PIO SETUP FIS for success case.
3. Add command status register check for IDE DMA transfer.
4. ScsiDiskReadCapacity() in ScsiDisk should return EFI_SUCCESS if SENSE Data request is success.
Signed-off-by: erictian
Reviewed-by: rsun3
Reviewed-by: xdu2
Reviewed-by: mdkinney
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12658 6f19259b-4bc3-4df7-8a09-765794883524
GCC 4.6 generates a warning when a variable is set,
but never used.
Signed-off-by: jljusten
Reviewed-by: lgao4
Reviewed-by: erictian
Reviewed-by: rsun3
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12617 6f19259b-4bc3-4df7-8a09-765794883524
