/** @file
Copyright (c) 2024, Intel Corporation. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
* Neither the name of Intel Corporation nor the names of its contributors may
be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
This file is automatically generated. Please do NOT modify !!!
**/
#ifndef __FSPSUPD_H__
#define __FSPSUPD_H__
#include
#pragma pack(1)
///
/// Azalia Header structure
///
typedef struct {
UINT16 VendorId; ///< Codec Vendor ID
UINT16 DeviceId; ///< Codec Device ID
UINT8 RevisionId; ///< Revision ID of the codec. 0xFF matches any revision.
UINT8 SdiNum; ///< SDI number, 0xFF matches any SDI.
UINT16 DataDwords; ///< Number of data DWORDs pointed by the codec data buffer.
UINT32 Reserved; ///< Reserved for future use. Must be set to 0.
} AZALIA_HEADER;
///
/// Audio Azalia Verb Table structure
///
typedef struct {
AZALIA_HEADER Header; ///< AZALIA PCH header
UINT32 *Data; ///< Pointer to the data buffer. Its length is specified in the header
} AUDIO_AZALIA_VERB_TABLE;
///
/// Refer to the definition of PCH_INT_PIN
///
typedef enum {
SiPchNoInt, ///< No Interrupt Pin
SiPchIntA,
SiPchIntB,
SiPchIntC,
SiPchIntD
} SI_PCH_INT_PIN;
///
/// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device.
///
typedef struct {
UINT8 Device; ///< Device number
UINT8 Function; ///< Device function
UINT8 IntX; ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN)
UINT8 Irq; ///< IRQ to be set for device.
} SI_PCH_DEVICE_INTERRUPT_CONFIG;
#define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG 64 ///< Number of all PCH devices
/** Fsp S Configuration
**/
typedef struct {
/** Offset 0x0040 - Logo Pointer
Points to PEI Display Logo Image
**/
UINT32 LogoPtr;
/** Offset 0x0044 - Logo Size
Size of PEI Display Logo Image
**/
UINT32 LogoSize;
/** Offset 0x0048 - Blt Buffer Address
Address of Blt buffer
**/
UINT32 BltBufferAddress;
/** Offset 0x004C - Blt Buffer Size
Size of Blt Buffer, is equal to PixelWidth * PixelHeight * 4 bytes (the size of
EFI_GRAPHICS_OUTPUT_BLT_PIXEL)
**/
UINT32 BltBufferSize;
/** Offset 0x0050 - Graphics Configuration Ptr
Points to VBT
**/
UINT32 GraphicsConfigPtr;
/** Offset 0x0054 - Enable Device 4
Enable/disable Device 4
$EN_DIS
**/
UINT8 Device4Enable;
/** Offset 0x0055 - Show SPI controller
Enable/disable to show SPI controller.
$EN_DIS
**/
UINT8 ShowSpiController;
/** Offset 0x0056
**/
UINT8 Rsvd010[2];
/** Offset 0x0058 - MicrocodeRegionBase
Memory Base of Microcode Updates
**/
UINT32 MicrocodeRegionBase;
/** Offset 0x005C - MicrocodeRegionSize
Size of Microcode Updates
**/
UINT32 MicrocodeRegionSize;
/** Offset 0x0060 - Turbo Mode
Enable/Disable processor Turbo Mode. 0:disable, 1: Enable
$EN_DIS
**/
UINT8 TurboMode;
/** Offset 0x0061 - Enable SATA SALP Support
Enable/disable SATA Aggressive Link Power Management.
$EN_DIS
**/
UINT8 SataSalpSupport;
/** Offset 0x0062 - Enable SATA ports
Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1,
and so on.
**/
UINT8 SataPortsEnable[8];
/** Offset 0x006A - Enable SATA DEVSLP Feature
Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each
port, byte0 for port0, byte1 for port1, and so on.
**/
UINT8 SataPortsDevSlp[8];
/** Offset 0x0072
**/
UINT8 Rsvd020[2];
/** Offset 0x0074 - SATA DEVSLP GPIO Pin
Select SATA DEVSLP Pin. Refer to GPIO_*_MUXING_SATA_DEVSLP_x* for possible values.
**/
UINT32 SataPortDevSlpPinMux[8];
/** Offset 0x0094 - Enable USB2 ports
Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for
port1, and so on.
**/
UINT8 PortUsb20Enable[16];
/** Offset 0x00A4 - Enable USB3 ports
Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for
port1, and so on.
**/
UINT8 PortUsb30Enable[10];
/** Offset 0x00AE - Enable xDCI controller
Enable/disable to xDCI controller.
$EN_DIS
**/
UINT8 XdciEnable;
/** Offset 0x00AF
**/
UINT8 Rsvd030;
/** Offset 0x00B0 - Address of PCH_DEVICE_INTERRUPT_CONFIG table.
The address of the table of PCH_DEVICE_INTERRUPT_CONFIG.
**/
UINT32 DevIntConfigPtr;
/** Offset 0x00B4 - Number of DevIntConfig Entry
Number of Device Interrupt Configuration Entry. If this is not zero, the DevIntConfigPtr
must not be NULL.
**/
UINT8 NumOfDevIntConfig;
/** Offset 0x00B5 - PIRQx to IRQx Map Config
PIRQx to IRQx mapping. The valid value is 0x00 to 0x0F for each. First byte is for
PIRQA, second byte is for PIRQB, and so on. The setting is only available in Legacy
8259 PCI mode.
**/
UINT8 PxRcConfig[8];
/** Offset 0x00BD - Select GPIO IRQ Route
GPIO IRQ Select. The valid value is 14 or 15.
**/
UINT8 GpioIrqRoute;
/** Offset 0x00BE - Select SciIrqSelect
SCI IRQ Select. The valid value is 9, 10, 11, and 20, 21, 22, 23 for APIC only.
**/
UINT8 SciIrqSelect;
/** Offset 0x00BF - Select TcoIrqSelect
TCO IRQ Select. The valid value is 9, 10, 11, 20, 21, 22, 23.
**/
UINT8 TcoIrqSelect;
/** Offset 0x00C0 - Enable/Disable Tco IRQ
Enable/disable TCO IRQ
$EN_DIS
**/
UINT8 TcoIrqEnable;
/** Offset 0x00C1 - PCH HDA Verb Table Entry Number
Number of Entries in Verb Table.
**/
UINT8 PchHdaVerbTableEntryNum;
/** Offset 0x00C2
**/
UINT8 Rsvd040[2];
/** Offset 0x00C4 - PCH HDA Verb Table Pointer
Pointer to Array of pointers to Verb Table.
**/
UINT32 PchHdaVerbTablePtr;
/** Offset 0x00C8 - PCH HDA Codec Sx Wake Capability
Capability to detect wake initiated by a codec in Sx
**/
UINT8 PchHdaCodecSxWakeCapability;
/** Offset 0x00C9 - Enable SATA
Enable/disable SATA controller.
$EN_DIS
**/
UINT8 SataEnable;
/** Offset 0x00CA - SATA Mode
Select SATA controller working mode.
0:AHCI, 1:RAID
**/
UINT8 SataMode;
/** Offset 0x00CB - SPIn Device Mode
Selects SPI operation mode. N represents controller index: SPI0, SPI1, ... Available
modes: 0:SerialIoSpiDisabled, 1:SerialIoSpiPci, 2:SerialIoSpiHidden
**/
UINT8 SerialIoSpiMode[7];
/** Offset 0x00D2 - SPI Chip Select Polarity
Sets polarity for each chip Select. Available options: 0:SerialIoSpiCsActiveLow,
1:SerialIoSpiCsActiveHigh
**/
UINT8 SerialIoSpiCsPolarity[14];
/** Offset 0x00E0 - SPI Chip Select Enable
0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled
**/
UINT8 SerialIoSpiCsEnable[14];
/** Offset 0x00EE - SPIn Default Chip Select Output
Sets Default CS as Output. N represents controller index: SPI0, SPI1, ... Available
options: 0:CS0, 1:CS1
**/
UINT8 SerialIoSpiDefaultCsOutput[7];
/** Offset 0x00F5 - SPIn Default Chip Select Mode HW/SW
Sets Default CS Mode Hardware or Software. N represents controller index: SPI0,
SPI1, ... Available options: 0:HW, 1:SW
**/
UINT8 SerialIoSpiCsMode[7];
/** Offset 0x00FC - SPIn Default Chip Select State Low/High
Sets Default CS State Low or High. N represents controller index: SPI0, SPI1, ...
Available options: 0:Low, 1:High
**/
UINT8 SerialIoSpiCsState[7];
/** Offset 0x0103
**/
UINT8 Rsvd050[1];
/** Offset 0x0104 - Serial IO SPI CS Pin Muxing
Select SerialIo SPI CS pin muxing. Refer to GPIO_*_MUXING_SERIALIO_SPIx_CS* for
possible values.
**/
UINT32 SerialIoSpiCsPinMux[14];
/** Offset 0x013C - Serial IO SPI CLK Pin Muxing
Select SerialIo SPI CS pin muxing. Refer to GPIO_*_MUXING_SERIALIO_SPIx_CLK* for
possible values.
**/
UINT32 SerialIoSpiClkPinMux[7];
/** Offset 0x0158 - Serial IO SPI MISO Pin Muxing
Select SerialIo SPI MISO pin muxing. Refer to GPIO_*_MUXING_SERIALIO_SPIx_MISO*
for possible values.
**/
UINT32 SerialIoSpiMisoPinMux[7];
/** Offset 0x0174 - Serial IO SPI MOSI Pin Muxing
Select SerialIo SPI MOSI pin muxing. Refer to GPIO_*_MUXING_SERIALIO_SPIx_MOSI*
for possible values.
**/
UINT32 SerialIoSpiMosiPinMux[7];
/** Offset 0x0190 - UARTn Device Mode
Selects Uart operation mode. N represents controller index: Uart0, Uart1, ... Available
modes: 0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
4:SerialIoUartSkipInit
**/
UINT8 SerialIoUartMode[7];
/** Offset 0x0197
**/
UINT8 Rsvd060[1];
/** Offset 0x0198 - Default BaudRate for each Serial IO UART
Set default BaudRate Supported from 0 - default to 6000000
**/
UINT32 SerialIoUartBaudRate[7];
/** Offset 0x01B4 - Default ParityType for each Serial IO UART
Set default Parity. 0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity
**/
UINT8 SerialIoUartParity[7];
/** Offset 0x01BB - Default DataBits for each Serial IO UART
Set default word length. 0: Default, 5,6,7,8
**/
UINT8 SerialIoUartDataBits[7];
/** Offset 0x01C2 - Default StopBits for each Serial IO UART
Set default stop bits. 0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3:
TwoStopBits
**/
UINT8 SerialIoUartStopBits[7];
/** Offset 0x01C9 - Power Gating mode for each Serial IO UART that works in COM mode
Set Power Gating. 0: Disabled, 1: Enabled, 2: Auto
**/
UINT8 SerialIoUartPowerGating[7];
/** Offset 0x01D0 - Enable Dma for each Serial IO UART that supports it
Set DMA/PIO mode. 0: Disabled, 1: Enabled
**/
UINT8 SerialIoUartDmaEnable[7];
/** Offset 0x01D7 - Enables UART hardware flow control, CTS and RTS lines
Enables UART hardware flow control, CTS and RTS lines.
**/
UINT8 SerialIoUartAutoFlow[7];
/** Offset 0x01DE
**/
UINT8 Rsvd070[2];
/** Offset 0x01E0 - SerialIoUartRtsPinMuxPolicy
Select SerialIo Uart Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS*
for possible values.
**/
UINT32 SerialIoUartRtsPinMuxPolicy[7];
/** Offset 0x01FC - SerialIoUartCtsPinMuxPolicy
Select SerialIo Uart Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS*
for possible values.
**/
UINT32 SerialIoUartCtsPinMuxPolicy[7];
/** Offset 0x0218 - SerialIoUartRxPinMuxPolicy
Select SerialIo Uart Rx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RX* for
possible values.
**/
UINT32 SerialIoUartRxPinMuxPolicy[7];
/** Offset 0x0234 - SerialIoUartTxPinMuxPolicy
Select SerialIo Uart Tx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_TX* for
possible values.
**/
UINT32 SerialIoUartTxPinMuxPolicy[7];
/** Offset 0x0250 - Serial IO UART DBG2 table
Enable or disable Serial Io UART DBG2 table, default is Disable; 0: Disable;
1: Enable.
**/
UINT8 SerialIoUartDbg2[7];
/** Offset 0x0257 - I2Cn Device Mode
Selects I2c operation mode. N represents controller index: I2c0, I2c1, ... Available
modes: 0:SerialIoI2cDisabled, 1:SerialIoI2cPci, 2:SerialIoI2cHidden
**/
UINT8 SerialIoI2cMode[8];
/** Offset 0x025F
**/
UINT8 Rsvd080[1];
/** Offset 0x0260 - Serial IO I2C SDA Pin Muxing
Select SerialIo I2c Sda pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SDA* for
possible values.
**/
UINT32 PchSerialIoI2cSdaPinMux[8];
/** Offset 0x0280 - Serial IO I2C SCL Pin Muxing
Select SerialIo I2c Scl pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SCL* for
possible values.
**/
UINT32 PchSerialIoI2cSclPinMux[8];
/** Offset 0x02A0 - PCH SerialIo I2C Pads Termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C0,I2C1,... pads termination
respectively. One byte for each controller, byte0 for I2C0, byte1 for I2C1, and so on.
**/
UINT8 PchSerialIoI2cPadsTermination[8];
/** Offset 0x02A8 - I3C Device Mode
Selects I3c operation mode. Available modes: 0:SerialIoI3cDisabled, 1:SerialIoI3cPci,
2:SerialIoI3cPhantom (only applicable to I3C1, controlls GPIO enabling)
**/
UINT8 SerialIoI3cMode[2];
/** Offset 0x02AA
**/
UINT8 Rsvd090[2];
/** Offset 0x02AC - Serial IO I3C SDA Pin Muxing
Select SerialIo I3c Sda pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I3Cx_SDA* for
possible values.
**/
UINT32 SerialIoI3cSdaPinMux[2];
/** Offset 0x02B4 - Serial IO I3C SDA Pad Termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I3C0,I3C1,... pads termination
respectively. One byte for each controller, byte0 for I3C0, byte1 for I3C1, and so on.
**/
UINT8 SerialIoI3cSdaPadTermination[2];
/** Offset 0x02B6
**/
UINT8 Rsvd100[2];
/** Offset 0x02B8 - Serial IO I3C SCL Pin Muxing
Select SerialIo I3c Scl pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I3Cx_SCL* for
possible values.
**/
UINT32 SerialIoI3cSclPinMux[2];
/** Offset 0x02C0 - Serial IO I3C SCL Pad Termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I3C0,I3C1,... pads termination
respectively. One byte for each controller, byte0 for I3C0, byte1 for I3C1, and so on.
**/
UINT8 SerialIoI3cSclPadTermination[2];
/** Offset 0x02C2
**/
UINT8 Rsvd110[2];
/** Offset 0x02C4 - Serial IO I3C SCL FB Pin Muxing
Select SerialIo I3c SclFb pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I3Cx_SCL FB*
for possible values.
**/
UINT32 SerialIoI3cSclFbPinMux[2];
/** Offset 0x02CC - Serial IO I3C SCL FB Pad Termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I3C0,I3C1,... pads termination
respectively. One byte for each controller, byte0 for I3C0, byte1 for I3C1, and so on.
**/
UINT8 SerialIoI3cSclFbPadTermination[2];
/** Offset 0x02CE
**/
UINT8 Rsvd120[2];
/** Offset 0x02D0 - ISH GP GPIO Pin Muxing
Determines ISH GP GPIO Pin muxing. See GPIO_*_MUXING_ISH_GP_x_GPIO_*. 'x' are GP_NUMBER
**/
UINT32 IshGpGpioPinMuxing[12];
/** Offset 0x0300 - ISH UART Rx Pin Muxing
Determines ISH UART Rx Pin muxing. See GPIO_*_MUXING_ISH_UARTx_TXD_*
**/
UINT32 IshUartRxPinMuxing[3];
/** Offset 0x030C - ISH UART Tx Pin Muxing
Determines ISH UART Tx Pin muxing. See GPIO_*_MUXING_ISH_UARTx_RXD_*
**/
UINT32 IshUartTxPinMuxing[3];
/** Offset 0x0318 - ISH UART Rts Pin Muxing
Select ISH UART Rts Pin muxing. Refer to GPIO_*_MUXING_ISH_UARTx_RTS_* for possible values.
**/
UINT32 IshUartRtsPinMuxing[3];
/** Offset 0x0324 - ISH UART Rts Pin Muxing
Select ISH UART Cts Pin muxing. Refer to GPIO_*_MUXING_ISH_UARTx_CTS_* for possible values.
**/
UINT32 IshUartCtsPinMuxing[3];
/** Offset 0x0330 - ISH I2C SDA Pin Muxing
Select ISH I2C SDA Pin muxing. Refer to GPIO_*_MUXING_ISH_I2Cx_SDA_* for possible values.
**/
UINT32 IshI2cSdaPinMuxing[3];
/** Offset 0x033C - ISH I2C SCL Pin Muxing
Select ISH I2C SCL Pin muxing. Refer to GPIO_*_MUXING_ISH_I2Cx_SCL_* for possible values.
**/
UINT32 IshI2cSclPinMuxing[3];
/** Offset 0x0348 - ISH I3C SDA Pin Muxing
Select ISH I3C SDA Pin muxing. Refer to GPIO_*_MUXING_ISH_I3Cx_SDA_* for possible values.
**/
UINT32 IshI3cSdaPinMuxing;
/** Offset 0x034C - ISH I3C SCL Pin Muxing
Select ISH I3C SCL Pin muxing. Refer to GPIO_*_MUXING_ISH_I3Cx_SCL_* for possible values.
**/
UINT32 IshI3cSclPinMuxing;
/** Offset 0x0350 - ISH SPI MOSI Pin Muxing
Select ISH SPI MOSI Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_MOSI_* for possible values.
**/
UINT32 IshSpiMosiPinMuxing[2];
/** Offset 0x0358 - ISH SPI MISO Pin Muxing
Select ISH SPI MISO Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_MISO_* for possible values.
**/
UINT32 IshSpiMisoPinMuxing[2];
/** Offset 0x0360 - ISH SPI CLK Pin Muxing
Select ISH SPI CLK Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_CLK_* for possible values.
**/
UINT32 IshSpiClkPinMuxing[2];
/** Offset 0x0368 - ISH SPI CS#N Pin Muxing
Select ISH SPI CS#N Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_CS_* for possible
values. N-SPI number, 0-1.
**/
UINT32 IshSpiCsPinMuxing[4];
/** Offset 0x0378 - ISH GP GPIO Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo GP#N GPIO pads termination
respectively. #N are GP_NUMBER, not strictly relate to indexes of this table. Index
0-23 -> ISH_GP_0-23, Index 24-25 -> ISH_GP_30-31
**/
UINT8 IshGpGpioPadTermination[12];
/** Offset 0x0384 - ISH UART Rx Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Rx pads termination
respectively. #N-byte for each controller, byte0 for UART0 Rx, byte1 for UART1
Rx, and so on.
**/
UINT8 IshUartRxPadTermination[3];
/** Offset 0x0387 - ISH UART Tx Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Tx pads termination
respectively. #N-byte for each controller, byte0 for UART0 Tx, byte1 for UART1
Tx, and so on.
**/
UINT8 IshUartTxPadTermination[3];
/** Offset 0x038A - ISH UART Rts Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Rts pads termination
respectively. #N-byte for each controller, byte0 for UART0 Rts, byte1 for UART1
Rts, and so on.
**/
UINT8 IshUartRtsPadTermination[3];
/** Offset 0x038D - ISH UART Rts Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Cts pads termination
respectively. #N-byte for each controller, byte0 for UART0 Cts, byte1 for UART1
Cts, and so on.
**/
UINT8 IshUartCtsPadTermination[3];
/** Offset 0x0390 - ISH I2C SDA Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C#N Sda pads termination
respectively. #N-byte for each controller, byte0 for I2C0 Sda, byte1 for I2C1 Sda,
and so on.
**/
UINT8 IshI2cSdaPadTermination[3];
/** Offset 0x0393 - ISH I3C SDA Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C#N Sda pads termination
respectively. #N-byte for each controller, byte0 for I2C0 Sda, byte1 for I2C1 Sda,
and so on.
**/
UINT8 IshI3cSdaPadTermination;
/** Offset 0x0394 - ISH I2C SCL Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C#N Scl pads termination
respectively. #N-byte for each controller, byte0 for I2C0 Scl, byte1 for I2C1 Scl,
and so on.
**/
UINT8 IshI2cSclPadTermination[3];
/** Offset 0x0397 - ISH I3C SCL Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C#N Scl pads termination
respectively. #N-byte for each controller, byte0 for I2C0 Scl, byte1 for I2C1 Scl,
and so on.
**/
UINT8 IshI3cSclPadTermination;
/** Offset 0x0398 - ISH SPI MOSI Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Mosi pads termination
respectively. #N-byte for each controller, byte0 for SPI0 Mosi, byte1 for SPI1
Mosi, and so on.
**/
UINT8 IshSpiMosiPadTermination[2];
/** Offset 0x039A - ISH SPI MISO Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Miso pads termination
respectively. #N-byte for each controller, byte0 for SPI0 Miso, byte1 for SPI1
Miso, and so on.
**/
UINT8 IshSpiMisoPadTermination[2];
/** Offset 0x039C - ISH SPI CLK Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Clk pads termination
respectively. #N-byte for each controller, byte0 for SPI0 Clk, byte1 for SPI1 Clk,
and so on.
**/
UINT8 IshSpiClkPadTermination[2];
/** Offset 0x039E - ISH SPI CS#N Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Cs#M pads termination
respectively. N*M-byte for each controller, byte0 for SPI0 Cs0, byte1 for SPI1
Cs1, SPI1 Cs0, byte2, SPI1 Cs1, byte3
**/
UINT8 IshSpiCsPadTermination[4];
/** Offset 0x03A2 - Enable PCH ISH SPI Cs#N pins assigned
Set if ISH SPI Cs#N pins are to be enabled by BIOS. 0: Disable; 1: Enable. N-Cs
number: 0-1
**/
UINT8 PchIshSpiCsEnable[4];
/** Offset 0x03A6 - USB Per Port HS Preemphasis Bias
USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port.
**/
UINT8 Usb2PhyPetxiset[16];
/** Offset 0x03B6 - USB Per Port HS Transmitter Bias
USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port.
**/
UINT8 Usb2PhyTxiset[16];
/** Offset 0x03C6 - USB Per Port HS Transmitter Emphasis
USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON,
10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port.
**/
UINT8 Usb2PhyPredeemp[16];
/** Offset 0x03D6 - USB Per Port Half Bit Pre-emphasis
USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis.
One byte for each port.
**/
UINT8 Usb2PhyPehalfbit[16];
/** Offset 0x03E6 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment
Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value
in arrary can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxDeEmphEnable[10];
/** Offset 0x03F0 - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting
USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16],
Default = 29h (approximately -3.5dB De-Emphasis). One byte for each port.
**/
UINT8 Usb3HsioTxDeEmph[10];
/** Offset 0x03FA - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment
Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value
in arrary can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxDownscaleAmpEnable[10];
/** Offset 0x0404 - USB 3.0 TX Output Downscale Amplitude Adjustment
USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], Default
= 00h. One byte for each port.
**/
UINT8 Usb3HsioTxDownscaleAmp[10];
/** Offset 0x040E
**/
UINT8 PchUsb3HsioCtrlAdaptOffsetCfgEnable[10];
/** Offset 0x0418
**/
UINT8 PchUsb3HsioFilterSelNEnable[10];
/** Offset 0x0422
**/
UINT8 PchUsb3HsioFilterSelPEnable[10];
/** Offset 0x042C
**/
UINT8 PchUsb3HsioOlfpsCfgPullUpDwnResEnable[10];
/** Offset 0x0436
**/
UINT8 PchUsb3HsioCtrlAdaptOffsetCfg[10];
/** Offset 0x0440
**/
UINT8 PchUsb3HsioOlfpsCfgPullUpDwnRes[10];
/** Offset 0x044A
**/
UINT8 PchUsb3HsioFilterSelN[10];
/** Offset 0x0454
**/
UINT8 PchUsb3HsioFilterSelP[10];
/** Offset 0x045E - Enable LAN
Enable/disable LAN controller.
$EN_DIS
**/
UINT8 PchLanEnable;
/** Offset 0x045F - Enable PCH TSN
Enable/disable TSN on the PCH.
$EN_DIS
**/
UINT8 PchTsnEnable;
/** Offset 0x0460 - TSN Link Speed
Set TSN Link Speed.
0: 24Mhz 2.5Gbps, 1: 24Mhz 1Gbps, 2: 38.4Mhz 2.5Gbps, 3: 38.4Mhz 1Gbps
**/
UINT8 PchTsnLinkSpeed;
/** Offset 0x0461
**/
UINT8 Rsvd130[3];
/** Offset 0x0464 - PCH TSN MAC Address High Bits
Set TSN MAC Address High.
**/
UINT32 PchTsnMacAddressHigh;
/** Offset 0x0468 - PCH TSN MAC Address Low Bits
Set TSN MAC Address Low.
**/
UINT32 PchTsnMacAddressLow;
/** Offset 0x046C - PCH TSN MAC Address High Bits
Set TSN MAC Address High.
**/
UINT32 PchTsn1MacAddressHigh;
/** Offset 0x0470 - PCH TSN MAC Address Low Bits
Set TSN MAC Address Low.
**/
UINT32 PchTsn1MacAddressLow;
/** Offset 0x0474 - PCIe PTM enable/disable
Enable/disable Precision Time Measurement for PCIE Root Ports.
**/
UINT8 PciePtm[29];
/** Offset 0x0491 - Disable DMI Power Gating
Enable/disable DMI Power Gating Disable.
$EN_DIS
**/
UINT8 DmiPowerGatingDis;
/** Offset 0x0492
**/
UINT8 Rsvd135[28];
/** Offset 0x04AE - USB PDO Programming
Enable/disable PDO programming for USB in PEI phase. Disabling will allow for programming
during later phase. 1: enable, 0: disable
$EN_DIS
**/
UINT8 UsbPdoProgramming;
/** Offset 0x04AF
**/
UINT8 Rsvd140[5];
/** Offset 0x04B4 - Power button debounce configuration
Debounce time for PWRBTN in microseconds. For values not supported by HW, they will
be rounded down to closest supported on. 0: disable, 250-1024000us: supported range
**/
UINT32 PmcPowerButtonDebounce;
/** Offset 0x04B8 - PCH eSPI Host and Device BME enabled
PCH eSPI Host and Device BME enabled
$EN_DIS
**/
UINT8 PchEspiBmeHostDeviceEnabled;
/** Offset 0x04B9 - PCH eSPI Link Configuration Lock (SBLCL)
Enable/Disable lock of communication through SET_CONFIG/GET_CONFIG to eSPI target
addresseses from range 0x0 - 0x7FF
$EN_DIS
**/
UINT8 PchEspiLockLinkConfiguration;
/** Offset 0x04BA - Mask to enable the usage of external V1p05 VR rail in specific S0ix or Sx states
Enable External V1P05 Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5
**/
UINT8 PchFivrExtV1p05RailEnabledStates;
/** Offset 0x04BB - Mask to enable the platform configuration of external V1p05 VR rail
External V1P05 Rail Supported Configuration
**/
UINT8 PchFivrExtV1p05RailSupportedVoltageStates;
/** Offset 0x04BC - External V1P05 Voltage Value that will be used in S0i2/S0i3 states
Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...)
**/
UINT16 PchFivrExtV1p05RailVoltage;
/** Offset 0x04BE - External V1P05 Icc Max Value
Granularity of this setting is 1mA and maximal possible value is 200mA
**/
UINT8 PchFivrExtV1p05RailIccMax;
/** Offset 0x04BF - Mask to enable the usage of external Vnn VR rail in specific S0ix or Sx states
Enable External Vnn Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5
**/
UINT8 PchFivrExtVnnRailEnabledStates;
/** Offset 0x04C0 - Mask to enable the platform configuration of external Vnn VR rail
External Vnn Rail Supported Configuration
**/
UINT8 PchFivrExtVnnRailSupportedVoltageStates;
/** Offset 0x04C1
**/
UINT8 Rsvd150;
/** Offset 0x04C2 - External Vnn Voltage Value that will be used in S0ix/Sx states
Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...), Default is set to 420
**/
UINT16 PchFivrExtVnnRailVoltage;
/** Offset 0x04C4 - External Vnn Icc Max Value that will be used in S0ix/Sx states
Granularity of this setting is 1mA and maximal possible value is 200mA
**/
UINT8 PchFivrExtVnnRailIccMax;
/** Offset 0x04C5 - Mask to enable the usage of external Vnn VR rail in Sx states
Use only if Ext Vnn Rail config is different in Sx. Enable External Vnn Rail in
Sx: BIT0-1:Reserved, BIT2:S3, BIT3:S4, BIT5:S5
**/
UINT8 PchFivrExtVnnRailSxEnabledStates;
/** Offset 0x04C6 - External Vnn Voltage Value that will be used in Sx states
Use only if Ext Vnn Rail config is different in Sx. Value is given in 2.5mV increments
(0=0mV, 1=2.5mV, 2=5mV...)
**/
UINT16 PchFivrExtVnnRailSxVoltage;
/** Offset 0x04C8 - External Vnn Icc Max Value that will be used in Sx states
Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting
is 1mA and maximal possible value is 200mA
**/
UINT8 PchFivrExtVnnRailSxIccMax;
/** Offset 0x04C9 - Transition time in microseconds from Low Current Mode Voltage to High Current Mode Voltage
This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
to low current mode voltage.
**/
UINT8 PchFivrVccinAuxLowToHighCurModeVolTranTime;
/** Offset 0x04CA - Transition time in microseconds from Retention Mode Voltage to High Current Mode Voltage
This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
to retention mode voltage.
**/
UINT8 PchFivrVccinAuxRetToHighCurModeVolTranTime;
/** Offset 0x04CB - Transition time in microseconds from Retention Mode Voltage to Low Current Mode Voltage
This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
to retention mode voltage.
**/
UINT8 PchFivrVccinAuxRetToLowCurModeVolTranTime;
/** Offset 0x04CC - Transition time in microseconds from Off (0V) to High Current Mode Voltage
This field has 1us resolution. When value is 0 Transition to 0V is disabled.
**/
UINT16 PchFivrVccinAuxOffToHighCurModeVolTranTime;
/** Offset 0x04CE - PMC Debug Message Enable
When Enabled, PMC HW will send debug messages to trace hub; When Disabled, PMC HW
will never send debug meesages to trace hub. Noted: When Enabled, may not enter S0ix
$EN_DIS
**/
UINT8 PmcDbgMsgEn;
/** Offset 0x04CF
**/
UINT8 Rsvd160;
/** Offset 0x04D0 - Pointer to ChipsetInit Binary
ChipsetInit Binary Pointer.
**/
UINT32 ChipsetInitBinPtr;
/** Offset 0x04D4 - Length of ChipsetInit Binary
ChipsetInit Binary Length.
**/
UINT32 ChipsetInitBinLen;
/** Offset 0x04D8 - Pointer to NPHY Binary
Nphy Binary Pointer.
**/
UINT32 NphyBinPtr;
/** Offset 0x04DC - Length of NPHY Binary
Nphy Binary Length.
**/
UINT32 NphyBinLen;
/** Offset 0x04E0 - Pointer to SYNPS PHY Binary
Synps Binary Pointer.
**/
UINT32 SynpsPhyBinPtr;
/** Offset 0x04E4 - Length of SYNPS PHY Binary
Synps Binary Length.
**/
UINT32 SynpsPhyBinLen;
/** Offset 0x04E8 - FIVR Dynamic Power Management
Enable/Disable FIVR Dynamic Power Management.
$EN_DIS
**/
UINT8 PchFivrDynPm;
/** Offset 0x04E9
**/
UINT8 Rsvd170;
/** Offset 0x04EA - External V1P05 Icc Max Value
Granularity of this setting is 1mA and maximal possible value is 500mA
**/
UINT16 PchFivrExtV1p05RailIccMaximum;
/** Offset 0x04EC - External Vnn Icc Max Value that will be used in S0ix/Sx states
Granularity of this setting is 1mA and maximal possible value is 500mA
**/
UINT16 PchFivrExtVnnRailIccMaximum;
/** Offset 0x04EE - External Vnn Icc Max Value that will be used in Sx states
Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting
is 1mA and maximal possible value is 500mA
**/
UINT16 PchFivrExtVnnRailSxIccMaximum;
/** Offset 0x04F0 - USB Audio Offload enable
Enable/Disable USB Audio Offload capabilites. 0: disabled, 1: enabled (default)
$EN_DIS
**/
UINT8 PchXhciUaolEnable;
/** Offset 0x04F1 - PCH xHCI enable HS Interrupt IN Alarm
PCH xHCI enable HS Interrupt IN Alarm. 0: disabled (default), 1: enabled
$EN_DIS
**/
UINT8 PchXhciHsiiEnable;
/** Offset 0x04F2
**/
UINT8 Rsvd175[2];
/** Offset 0x04F4 - PCH GPIOV2 Unlock Data Buffer Address
Address of GPIO Unlock Data buffer
**/
UINT32 PchGpioUnlockDataPtr;
/** Offset 0x04F8 - PCH GPIOV2 Unlock Data Buffer Size
Size of PCH GPIO Unlock Data Buffer
**/
UINT32 PchGpioUnlockDataSize;
/** Offset 0x04FC - PchPostMemRsvd
Reserved for PCH Post-Mem
$EN_DIS
**/
UINT8 PchPostMemRsvd[2];
/** Offset 0x04FE - CNVi Configuration
This option allows for automatic detection of Connectivity Solution. [Auto Detection]
assumes that CNVi will be enabled when available, [Disable] allows for disabling CNVi.
0:Disable, 1:Auto
**/
UINT8 CnviMode;
/** Offset 0x04FF - CNVi Wi-Fi Core
Enable/Disable CNVi Wi-Fi Core, Default is ENABLE. 0: DISABLE, 1: ENABLE
$EN_DIS
**/
UINT8 CnviWifiCore;
/** Offset 0x0500 - CNVi BT Core
Enable/Disable CNVi BT Core, Default is ENABLE. 0: DISABLE, 1: ENABLE
$EN_DIS
**/
UINT8 CnviBtCore;
/** Offset 0x0501 - CNVi BT Audio Offload
Enable/Disable BT Audio Offload, Default is ENABLE. 0: DISABLE, 1: ENABLE
$EN_DIS
**/
UINT8 CnviBtAudioOffload;
/** Offset 0x0502
**/
UINT8 Rsvd180[2];
/** Offset 0x0504 - CNVi RF_RESET pin muxing
Select CNVi RF_RESET# pin depending on board routing. LP/P/M: GPP_A8 = 0x2942E408(default)
or GPP_F4 = 0x194CE404. H/S: 0. Refer to GPIO_*_MUXING_CNVI_RF_RESET_* in GpioPins*.h.
**/
UINT32 CnviRfResetPinMux;
/** Offset 0x0508 - CNVi CLKREQ pin muxing
Select CNVi CLKREQ pin depending on board routing. LP/P/M: GPP_A9 = 0x3942E609(default)
or GPP_F5 = 0x394CE605. H/S: 0. Refer to GPIO_*_MUXING_CNVI_CRF_XTAL_CLKREQ_* in
GpioPins*.h.
**/
UINT32 CnviClkreqPinMux;
/** Offset 0x050C - Enable Host C10 reporting through eSPI
Enable/disable Host C10 reporting to Device via eSPI Virtual Wire.
$EN_DIS
**/
UINT8 PchEspiHostC10ReportEnable;
/** Offset 0x050D - PCH USB2 PHY Power Gating enable
1: Will enable USB2 PHY SUS Well Power Gating, 0: Will not enable PG of USB2 PHY
Sus Well PG
$EN_DIS
**/
UINT8 PmcUsb2PhySusPgEnable;
/** Offset 0x050E - PCH USB OverCurrent mapping enable
1: Will program USB OC pin mapping in xHCI controller memory, 0: Will clear OC pin
mapping allow for NOA usage of OC pins
$EN_DIS
**/
UINT8 PchUsbOverCurrentEnable;
/** Offset 0x050F - Espi Lgmr Memory Range decode
This option enables or disables espi lgmr
$EN_DIS
**/
UINT8 PchEspiLgmrEnable;
/** Offset 0x0510 - External V1P05 Control Ramp Timer value
Hold off time to be used when changing the v1p05_ctrl for external bypass value in us
**/
UINT8 PchFivrExtV1p05RailCtrlRampTmr;
/** Offset 0x0511 - External VNN Control Ramp Timer value
Hold off time to be used when changing the vnn_ctrl for external bypass value in us
**/
UINT8 PchFivrExtVnnRailCtrlRampTmr;
/** Offset 0x0512 - Set SATA DEVSLP GPIO Reset Config
Set SATA DEVSLP GPIO Reset Config per port. 0x00 - GpioResetDefault, 0x01 - GpioResumeReset,
0x03 - GpioHostDeepReset, 0x05 - GpioPlatformReset, 0x07 - GpioDswReset. One byte
for each port, byte0 for port0, byte1 for port1, and so on.
**/
UINT8 SataPortsDevSlpResetConfig[8];
/** Offset 0x051A - PCHHOT# pin
Enable PCHHOT# pin assertion when temperature is higher than PchHotLevel. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PchHotEnable;
/** Offset 0x051B - SATA LED
SATA LED indicating SATA controller activity. 0: disable, 1: enable
$EN_DIS
**/
UINT8 SataLedEnable;
/** Offset 0x051C - VRAlert# Pin
When VRAlert# feature pin is enabled and its state is '0', the PMC requests throttling
to a T3 Tstate to the PCH throttling unit.. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PchPmVrAlert;
/** Offset 0x051D - AMT Switch
Enable/Disable. 0: Disable, 1: enable, Enable or disable AMT functionality.
$EN_DIS
**/
UINT8 AmtEnabled;
/** Offset 0x051E - WatchDog Timer Switch
Enable/Disable. 0: Disable, 1: enable, Enable or disable WatchDog timer. Setting
is invalid if AmtEnabled is 0.
$EN_DIS
**/
UINT8 WatchDogEnabled;
/** Offset 0x051F - PET Progress
Enable/Disable. 0: Disable, 1: enable, Enable/Disable PET Events Progress to receive
PET Events. Setting is invalid if AmtEnabled is 0.
$EN_DIS
**/
UINT8 FwProgress;
/** Offset 0x0520 - SOL Switch
Enable/Disable. 0: Disable, 1: enable, Serial Over Lan enable/disable state by Mebx.
Setting is invalid if AmtEnabled is 0.
$EN_DIS
**/
UINT8 AmtSolEnabled;
/** Offset 0x0521
**/
UINT8 Rsvd190;
/** Offset 0x0522 - OS Timer
16 bits Value, Set OS watchdog timer. Setting is invalid if AmtEnabled is 0.
**/
UINT16 WatchDogTimerOs;
/** Offset 0x0524 - BIOS Timer
16 bits Value, Set BIOS watchdog timer. Setting is invalid if AmtEnabled is 0.
**/
UINT16 WatchDogTimerBios;
/** Offset 0x0526 - PCH PCIe root port connection type
0: built-in device, 1:slot
**/
UINT8 PcieRpSlotImplemented[29];
/** Offset 0x0543 - PCIE RP Access Control Services Extended Capability
Enable/Disable PCIE RP Access Control Services Extended Capability
**/
UINT8 PcieRpAcsEnabled[29];
/** Offset 0x0560 - PCIE RP Clock Power Management
Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal
can still be controlled by L1 PM substates mechanism
**/
UINT8 PcieRpEnableCpm[29];
/** Offset 0x057D
**/
UINT8 Rsvd200[3];
/** Offset 0x0580 - PCIE RP Detect Timeout Ms
The number of milliseconds within 0~65535 in reference code will wait for link to
exit Detect state for enabled ports before assuming there is no device and potentially
disabling the port.
**/
UINT16 PcieRpDetectTimeoutMs[29];
/** Offset 0x05BA - ModPHY SUS Power Domain Dynamic Gating
Enable/Disable ModPHY SUS Power Domain Dynamic Gating. Setting not supported on
PCH-H. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PmcModPhySusPgEnable;
/** Offset 0x05BB - V1p05-PHY supply external FET control
Enable/Disable control using EXT_PWR_GATE# pin of external FET to power gate v1p05-PHY
supply. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PmcV1p05PhyExtFetControlEn;
/** Offset 0x05BC - V1p05-IS supply external FET control
Enable/Disable control using EXT_PWR_GATE2# pin of external FET to power gate v1p05-IS
supply. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PmcV1p05IsExtFetControlEn;
/** Offset 0x05BD - Enable/Disable PavpEnable
Enable(Default): Enable PavpEnable, Disable: Disable PavpEnable
$EN_DIS
**/
UINT8 PavpEnable;
/** Offset 0x05BE - Enable/Disable PeiGraphicsPeimInit
Enable(Default): FSP will initialize the framebuffer and provide it via EFI_PEI_GRAPHICS_INFO_HOB.
Disable: FSP will NOT initialize the framebuffer.
$EN_DIS
**/
UINT8 PeiGraphicsPeimInit;
/** Offset 0x05BF - Enable D3 Hot in TCSS
This policy will enable/disable D3 hot support in IOM
$EN_DIS
**/
UINT8 D3HotEnable;
/** Offset 0x05C0 - Enable or disable GNA device
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 GnaEnable;
/** Offset 0x05C1
**/
UINT8 Rsvd210[3];
/** Offset 0x05C4 - TypeC port GPIO setting
GPIO Ping number for Type C Aux Oritation setting, use the GpioPad that is defined
in GpioPinsXXXH.h and GpioPinsXXXLp.h as argument.(XXX is platform name, Ex: Mtl
= MeteorLake)
**/
UINT32 IomTypeCPortPadCfg[12];
/** Offset 0x05F4 - CPU USB3 Port Over Current Pin
Describe the specific over current pin number of USBC Port N.
**/
UINT8 CpuUsb3OverCurrentPin[8];
/** Offset 0x05FC - Enable D3 Cold in TCSS
This policy will enable/disable D3 cold support in IOM
$EN_DIS
**/
UINT8 D3ColdEnable;
/** Offset 0x05FD - Enable/Disable PCIe tunneling for USB4
Enable/Disable PCIe tunneling for USB4, default is enable
$EN_DIS
**/
UINT8 ITbtPcieTunnelingForUsb4;
/** Offset 0x05FE - Enable/Disable SkipFspGop
Enable: Skip FSP provided GOP driver, Disable(Default): Use FSP provided GOP driver
$EN_DIS
**/
UINT8 SkipFspGop;
/** Offset 0x05FF - Enable/Disable VPU Device
Enable(Default): Enable VPU Device, Disable: Disable VPU Device
$EN_DIS
**/
UINT8 VpuEnable;
/** Offset 0x0600 - TC State in TCSS
This TC C-State Limit in IOM
**/
UINT8 TcCstateLimit;
/** Offset 0x0601 - Display port support policy in TCSS
This policy will enable/disable Display port support in IOM
$EN_DIS
**/
UINT8 TcNotifyIgd;
/** Offset 0x0602
**/
UINT8 Rsvd220[2];
/** Offset 0x0604 - Intel Graphics VBT (Video BIOS Table) Size
Size of Internal Graphics VBT Image
**/
UINT32 VbtSize;
/** Offset 0x0608 - Platform LID Status for LFP Displays.
LFP Display Lid Status (LID_STATUS enum): 0 (Default): LidClosed, 1: LidOpen.
0: LidClosed, 1: LidOpen
**/
UINT8 LidStatus;
/** Offset 0x0609 - PchPostMemRsvd
Reserved for PCH Post-Mem
$EN_DIS
**/
UINT8 SaPostMemRsvd[8];
/** Offset 0x0611 - Enable VMD controller
Enable/disable to VMD controller.0: Disable; 1: Enable(Default)
$EN_DIS
**/
UINT8 VmdEnable;
/** Offset 0x0612 - Enable VMD Global Mapping
Enable/disable to VMD controller.0: Disable(Default); 1: Enable
$EN_DIS
**/
UINT8 VmdGlobalMapping;
/** Offset 0x0613 - Map port under VMD
Map/UnMap port under VMD
$EN_DIS
**/
UINT8 VmdPort[31];
/** Offset 0x0632 - VMD Port Bus
VMD Root port bus number.
**/
UINT8 VmdPortBus[31];
/** Offset 0x0651 - VMD Port Device
VMD Root port device number.
**/
UINT8 VmdPortDev[31];
/** Offset 0x0670 - VMD Port Func
VMD Root port function number.
**/
UINT8 VmdPortFunc[31];
/** Offset 0x068F
**/
UINT8 Rsvd230;
/** Offset 0x0690 - VMD Variable
VMD Variable Pointer.
**/
UINT32 VmdVariablePtr;
/** Offset 0x0694 - Temporary CfgBar address for VMD
VMD Variable Pointer.
**/
UINT32 VmdCfgBarBase;
/** Offset 0x0698 - Temporary MemBar1 address for VMD
VMD Variable Pointer.
**/
UINT32 VmdMemBar1Base;
/** Offset 0x069C - Temporary MemBar2 address for VMD
VMD Variable Pointer.
**/
UINT32 VmdMemBar2Base;
/** Offset 0x06A0 - TCSS CPU USB PDO Programming
Enable/disable PDO programming for TCSS CPU USB in PEI phase. Disabling will allow
for programming during later phase. 1: enable, 0: disable
$EN_DIS
**/
UINT8 TcssCpuUsbPdoProgramming;
/** Offset 0x06A1 - Enable/Disable PMC-PD Solution
This policy will enable/disable PMC-PD Solution vs EC-TCPC Solution
$EN_DIS
**/
UINT8 PmcPdEnable;
/** Offset 0x06A2 - TCSS Aux Orientation Override Enable
Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides
**/
UINT16 TcssAuxOri;
/** Offset 0x06A4 - TCSS HSL Orientation Override Enable
Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides
**/
UINT16 TcssHslOri;
/** Offset 0x06A6 - USB override in IOM
This policy will enable/disable USB Connect override in IOM
$EN_DIS
**/
UINT8 UsbOverride;
/** Offset 0x06A7 - ITBT Root Port Enable
ITBT Root Port Enable, 0:Disable, 1:Enable
0:Disable, 1:Enable
**/
UINT8 ITbtPcieRootPortEn[4];
/** Offset 0x06AB - TCSS USB Port Enable
Bits 0, 1, ... max Type C port control enables
**/
UINT8 UsbTcPortEn;
/** Offset 0x06AC - ITBTForcePowerOn Timeout value
ITBTForcePowerOn value. Specified increment values in miliseconds. Range is 0-1000.
100 = 100 ms.
**/
UINT16 ITbtForcePowerOnTimeoutInMs;
/** Offset 0x06AE - ITbtConnectTopology Timeout value
ITbtConnectTopologyTimeout value. Specified increment values in miliseconds. Range
is 0-10000. 100 = 100 ms.
**/
UINT16 ITbtConnectTopologyTimeoutInMs;
/** Offset 0x06B0 - VCCST request for IOM
This policy will enable/disable VCCST and also decides if message would be replayed in S4/S5
$EN_DIS
**/
UINT8 VccSt;
/** Offset 0x06B1
**/
UINT8 Rsvd240[1];
/** Offset 0x06B2 - ITBT DMA LTR
TCSS DMA1, DMA2 LTR value
**/
UINT16 ITbtDmaLtr[2];
/** Offset 0x06B6 - Enable/Disable CrashLog
Enable(Default): Enable CPU CrashLog, Disable: Disable CPU CrashLog
$EN_DIS
**/
UINT8 CpuCrashLogEnable;
/** Offset 0x06B7 - Enable/Disable PTM
This policy will enable/disable Precision Time Measurement for TCSS PCIe Root Ports
$EN_DIS
**/
UINT8 PtmEnabled[4];
/** Offset 0x06BB - PCIE RP Ltr Enable
Latency Tolerance Reporting Mechanism.
**/
UINT8 SaPcieItbtRpLtrEnable[4];
/** Offset 0x06BF - PCIE RP Snoop Latency Override Mode
Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
UINT8 SaPcieItbtRpSnoopLatencyOverrideMode[4];
/** Offset 0x06C3 - PCIE RP Snoop Latency Override Multiplier
Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
UINT8 SaPcieItbtRpSnoopLatencyOverrideMultiplier[4];
/** Offset 0x06C7
**/
UINT8 Rsvd250[1];
/** Offset 0x06C8 - PCIE RP Snoop Latency Override Value
Latency Tolerance Reporting, Snoop Latency Override Value.
**/
UINT16 SaPcieItbtRpSnoopLatencyOverrideValue[4];
/** Offset 0x06D0 - PCIE RP Non Snoop Latency Override Mode
Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
UINT8 SaPcieItbtRpNonSnoopLatencyOverrideMode[4];
/** Offset 0x06D4 - PCIE RP Non Snoop Latency Override Multiplier
Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
UINT8 SaPcieItbtRpNonSnoopLatencyOverrideMultiplier[4];
/** Offset 0x06D8 - PCIE RP Non Snoop Latency Override Value
Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
UINT16 SaPcieItbtRpNonSnoopLatencyOverrideValue[4];
/** Offset 0x06E0 - Force LTR Override
Force LTR Override.
**/
UINT8 SaPcieItbtRpForceLtrOverride[4];
/** Offset 0x06E4 - PCIE RP Ltr Config Lock
0: Disable; 1: Enable.
**/
UINT8 SaPcieItbtRpLtrConfigLock[4];
/** Offset 0x06E8 - Enable or Disable TXT
Enables utilization of additional hardware capabilities provided by Intel (R) Trusted
Execution Technology. Changes require a full power cycle to take effect. 0:
Disable, 1: Enable.
$EN_DIS
**/
UINT8 TxtEnable;
/** Offset 0x06E9
**/
UINT8 Rsvd260[3];
/** Offset 0x06EC - CpuBistData
Pointer CPU BIST Data
**/
UINT32 CpuBistData;
/** Offset 0x06F0 - CpuMpPpi
Optional pointer to the boot loader's implementation of EFI_PEI_MP_SERVICES_PPI.
If not NULL, FSP will use the boot loader's implementation of multiprocessing.
See section 5.1.4 of the FSP Integration Guide for more details.
**/
UINT32 CpuMpPpi;
/** Offset 0x06F4 - Boot frequency
Select the performance state that the BIOS will set starting from reset vector.
0: Maximum battery performance. 1: Maximum non-turbo performance. 2: Turbo performance
0:0, 1:1, 2:2
**/
UINT8 BootFrequency;
/** Offset 0x06F5
**/
UINT8 CpuPostMemRsvd[2];
/** Offset 0x06F7
**/
UINT8 Rsvd270[1];
/** Offset 0x06F8 - PpinSupport to view Protected Processor Inventory Number
PPIN Feature Support to view Protected Processor Inventory Number. Disable to turn
off this feature. When 'PPIN Enable Mode' is selected, this shows second option
where feature can be enabled based on EOM (End of Manufacturing) flag or it is
always enabled
0: Disable, 1: Enable, 2: Auto
**/
UINT8 PpinSupport;
/** Offset 0x06F9 - Memory size per thread allocated for Processor Trace
Memory size per thread for Processor Trace. Processor Trace requires 2^N alignment
and size in bytes per thread, from 4KB to 128MB.\n
0xff:none , 0:4k, 0x1:8k, 0x2:16k, 0x3:32k, 0x4:64k, 0x5:128k, 0x6:256k,
0x7:512k, 0x8:1M, 0x9:2M, 0xa:4M. 0xb:8M, 0xc:16M, 0xd:32M, 0xe:64M, 0xf:128M
**/
UINT8 ProcessorTraceMemSize;
/** Offset 0x06FA - Smbios Type4 Max Speed Override
Provide the option for platform to override the MaxSpeed field of Smbios Type 4.
If this value is not zero, it dominates the field.
**/
UINT16 SmbiosType4MaxSpeedOverride;
/** Offset 0x06FC - Advanced Encryption Standard (AES) feature
Enable or Disable Advanced Encryption Standard (AES) feature; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 AesEnable;
/** Offset 0x06FD - AvxDisable
Enable/Disable the AVX and AVX2 Instructions
0: Enable, 1: Disable
**/
UINT8 AvxDisable;
/** Offset 0x06FE - X2ApicEnable
Enable/Disable X2APIC Operating Mode. When this option is configured as 'Enabled',
'VT-d' option must be 'Enabled' and 'X2APIC Opt Out' option must be 'Disabled' as well.
$EN_DIS
**/
UINT8 X2ApicEnable;
/** Offset 0x06FF - ProcHot Demotion Algorithm configuration
ProcHot Demotion Algorithm configuration. Hardware Default/Disable; 0: Disable;
1: Hardware Default
0: Disable, 1: Hardware Default
**/
UINT8 ProcHotDemotion;
/** Offset 0x0700 - ReservedCpuPostMemProduction
Reserved for CPU Post-Mem Production
$EN_DIS
**/
UINT8 ReservedCpuPostMemProduction[56];
/** Offset 0x0738 - Enable Power Optimizer
Enable DMI Power Optimizer on PCH side.
$EN_DIS
**/
UINT8 PchPwrOptEnable;
/** Offset 0x0739 - PCH Flash Protection Ranges Write Enble
Write or erase is blocked by hardware.
**/
UINT8 PchWriteProtectionEnable[5];
/** Offset 0x073E - PCH Flash Protection Ranges Read Enble
Read is blocked by hardware.
**/
UINT8 PchReadProtectionEnable[5];
/** Offset 0x0743
**/
UINT8 Rsvd280[1];
/** Offset 0x0744 - PCH Protect Range Limit
Left shifted address by 12 bits with address bits 11:0 are assumed to be FFFh for
limit comparison.
**/
UINT16 PchProtectedRangeLimit[5];
/** Offset 0x074E - PCH Protect Range Base
Left shifted address by 12 bits with address bits 11:0 are assumed to be 0.
**/
UINT16 PchProtectedRangeBase[5];
/** Offset 0x0758 - Enable Pme
Enable Azalia wake-on-ring.
$EN_DIS
**/
UINT8 PchHdaPme;
/** Offset 0x0759 - HD Audio Link Frequency
HDA Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 0: 6MHz, 1: 12MHz, 2: 24MHz.
0: 6MHz, 1: 12MHz, 2: 24MHz
**/
UINT8 PchHdaLinkFrequency;
/** Offset 0x075A - Enable PCH ISH SPI Cs0 pins assigned
Set if ISH SPI Cs0 pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshSpiCs0Enable[1];
/** Offset 0x075B - Enable PCH Io Apic Entry 24-119
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIoApicEntry24_119;
/** Offset 0x075C - PCH Io Apic ID
This member determines IOAPIC ID. Default is 0x02.
**/
UINT8 PchIoApicId;
/** Offset 0x075D - Enable PCH ISH SPI pins assigned
Set if ISH SPI native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshSpiEnable[1];
/** Offset 0x075E - Enable PCH ISH UART pins assigned
Set if ISH UART native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshUartEnable[2];
/** Offset 0x0760 - Enable PCH ISH I2C pins assigned
Set if ISH I2C native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshI2cEnable[3];
/** Offset 0x0763 - Enable PCH ISH I3C pins assigned
Set if ISH I3C native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshI3cEnable;
/** Offset 0x0764 - Enable PCH ISH GP pins assigned
Set if ISH GP native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshGpEnable[12];
/** Offset 0x0770 - PCH ISH PDT Unlock Msg
0: False; 1: True.
$EN_DIS
**/
UINT8 PchIshPdtUnlock;
/** Offset 0x0771 - PCH ISH MSI Interrupts
0: False; 1: True.
$EN_DIS
**/
UINT8 PchIshMsiInterrupt;
/** Offset 0x0772 - Enable PCH Lan LTR capabilty of PCH internal LAN
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchLanLtrEnable;
/** Offset 0x0773 - Enable LOCKDOWN BIOS LOCK
Enable the BIOS Lock feature and set EISS bit (D31:F5:RegDCh[5]) for the BIOS region
protection.
$EN_DIS
**/
UINT8 PchLockDownBiosLock;
/** Offset 0x0774 - PCH Compatibility Revision ID
This member describes whether or not the CRID feature of PCH should be enabled.
$EN_DIS
**/
UINT8 PchCrid;
/** Offset 0x0775 - RTC BIOS Interface Lock
Enable RTC BIOS interface lock. When set, prevents RTC TS (BUC.TS) from being changed.
$EN_DIS
**/
UINT8 RtcBiosInterfaceLock;
/** Offset 0x0776 - RTC Cmos Memory Lock
Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper
and and lower 128-byte bank of RTC RAM.
$EN_DIS
**/
UINT8 RtcMemoryLock;
/** Offset 0x0777 - Enable PCIE RP HotPlug
Indicate whether the root port is hot plug available.
**/
UINT8 PcieRpHotPlug[29];
/** Offset 0x0794 - Enable PCIE RP Pm Sci
Indicate whether the root port power manager SCI is enabled.
$EN_DIS
**/
UINT8 PcieRpPmSci[29];
/** Offset 0x07B1 - Enable PCIE RP Transmitter Half Swing
Indicate whether the Transmitter Half Swing is enabled.
**/
UINT8 PcieRpTransmitterHalfSwing[29];
/** Offset 0x07CE - Enable PCIE RP Clk Req Detect
Probe CLKREQ# signal before enabling CLKREQ# based power management.
**/
UINT8 PcieRpClkReqDetect[29];
/** Offset 0x07EB - PCIE RP Advanced Error Report
Indicate whether the Advanced Error Reporting is enabled.
**/
UINT8 PcieRpAdvancedErrorReporting[29];
/** Offset 0x0808 - PCIE RP Unsupported Request Report
Indicate whether the Unsupported Request Report is enabled.
**/
UINT8 PcieRpUnsupportedRequestReport[29];
/** Offset 0x0825 - PCIE RP Fatal Error Report
Indicate whether the Fatal Error Report is enabled.
**/
UINT8 PcieRpFatalErrorReport[29];
/** Offset 0x0842 - PCIE RP No Fatal Error Report
Indicate whether the No Fatal Error Report is enabled.
**/
UINT8 PcieRpNoFatalErrorReport[29];
/** Offset 0x085F - PCIE RP Correctable Error Report
Indicate whether the Correctable Error Report is enabled.
**/
UINT8 PcieRpCorrectableErrorReport[29];
/** Offset 0x087C - PCIE RP System Error On Fatal Error
Indicate whether the System Error on Fatal Error is enabled.
**/
UINT8 PcieRpSystemErrorOnFatalError[29];
/** Offset 0x0899 - PCIE RP System Error On Non Fatal Error
Indicate whether the System Error on Non Fatal Error is enabled.
**/
UINT8 PcieRpSystemErrorOnNonFatalError[29];
/** Offset 0x08B6 - PCIE RP System Error On Correctable Error
Indicate whether the System Error on Correctable Error is enabled.
**/
UINT8 PcieRpSystemErrorOnCorrectableError[29];
/** Offset 0x08D3 - PCIE RP Max Payload
Max Payload Size supported, Default 256B, see enum PCH_PCIE_MAX_PAYLOAD.
**/
UINT8 PcieRpMaxPayload[29];
/** Offset 0x08F0 - Touch Host Controller Assignment
Assign THC 0x0:ThcAssignmentNone, 0x1:ThcAssignmentThc0, 0x2:ThcAssignmentThc1
**/
UINT8 ThcAssignment[2];
/** Offset 0x08F2 - Touch Host Controller Interrupt Pin Mux
Set THC Pin Muxing Value if signal can be enabled on multiple pads. Refer to GPIO_*_MUXING_THC_SPIx_INTB_*
for possible values.
**/
UINT8 ThcInterruptPinMuxing[8];
/** Offset 0x08FA - Touch Host Controller Mode
Switch between Intel THC protocol and Industry standard HID Over SPI protocol. 0x0:Thc, 0x1:Hid
**/
UINT8 ThcMode[2];
/** Offset 0x08FC - Touch Host Controller Wake On Touch
Based on this setting vGPIO for given THC will be in native mode, and additional
_CRS for wake will be exposed in ACPI
**/
UINT8 ThcWakeOnTouch[2];
/** Offset 0x08FE
**/
UINT8 Rsvd290[2];
/** Offset 0x0900 - Touch Host Controller Active Ltr
Expose Active Ltr for OS driver to set
**/
UINT32 ThcActiveLtr[2];
/** Offset 0x0908 - Touch Host Controller Idle Ltr
Expose Idle Ltr for OS driver to set
**/
UINT32 ThcIdleLtr[2];
/** Offset 0x0910 - Touch Host Controller Hid Over Spi ResetPad
Hid Over Spi ResetPad
**/
UINT32 ThcResetPad[2];
/** Offset 0x0918 - Touch Host Controller Hid Over Spi ResetPad Trigger
Hid Over Spi Reset Pad Trigger 0x0:Low, 0x1:High
**/
UINT32 ThcResetPadTrigger[2];
/** Offset 0x0920 - Touch Host Controller Hid Over Spi Connection Speed
Hid Over Spi Connection Speed - SPI Frequency
**/
UINT32 ThcHidSpiConnectionSpeed[2];
/** Offset 0x0928 - Touch Host Controller Hid Over Spi Limit PacketSize
When set, limits SPI read & write packet size to 64B. Otherwise, THC uses Max Soc
packet size for SPI Read and Write 0x0- Max Soc Packet Size, 0x11 - 64 Bytes
**/
UINT32 ThcHidSpiLimitPacketSize[2];
/** Offset 0x0930 - Touch Host Controller Hid Over Spi Limit PacketSize
Minimum amount of delay the THC/QUICKSPI driver must wait between end of write operation
and begin of read operation. This value shall be in 10us multiples 0x0: Disabled,
1-65535 (0xFFFF) - up to 655350 us
**/
UINT32 ThcPerformanceLimitation[2];
/** Offset 0x0938 - Touch Host Controller Hid Over Spi Input Report Header Address
Hid Over Spi Input Report Header Address
**/
UINT32 ThcHidSpiInputReportHeaderAddress[2];
/** Offset 0x0940 - Touch Host Controller Hid Over Spi Input Report Body Address
Hid Over Spi Input Report Body Address
**/
UINT32 ThcHidSpiInputReportBodyAddress[2];
/** Offset 0x0948 - Touch Host Controller Hid Over Spi Output Report Address
Hid Over Spi Output Report Address
**/
UINT32 ThcHidSpiOutputReportAddress[2];
/** Offset 0x0950 - Touch Host Controller Hid Over Spi Read Opcode
Hid Over Spi Read Opcode
**/
UINT32 ThcHidSpiReadOpcode[2];
/** Offset 0x0958 - Touch Host Controller Hid Over Spi Write Opcode
Hid Over Spi Write Opcode
**/
UINT32 ThcHidSpiWriteOpcode[2];
/** Offset 0x0960 - Touch Host Controller Hid Over Spi Flags
Hid Over Spi Flags 0x0:Single SPI Mode, 0x4000:Dual SPI Mode, 0x8000:Quad SPI Mode
**/
UINT32 ThcHidSpiFlags[2];
/** Offset 0x0968 - Touch Host Controller Hid Over Spi Reset Sequencing Delay [ms]
Policy control for reset sequencing delay (ACPI _INI, _RST) default 300ms
**/
UINT16 ThcResetSequencingDelay[2];
/** Offset 0x096C - PCIE RP Pcie Speed
Determines each PCIE Port speed capability. 0: Auto; 1: Gen1; 2: Gen2; 3: Gen3 (see:
PCIE_SPEED).
**/
UINT8 PcieRpPcieSpeed[29];
/** Offset 0x0989 - PCIE RP Physical Slot Number
Indicates the slot number for the root port. Default is the value as root port index.
**/
UINT8 PcieRpPhysicalSlotNumber[29];
/** Offset 0x09A6 - PCIE RP Completion Timeout
The root port completion timeout(see: PCIE_COMPLETION_TIMEOUT). Default is PchPcieCompletionTO_Default.
**/
UINT8 PcieRpCompletionTimeout[29];
/** Offset 0x09C3 - PCIE RP Aspm
The ASPM configuration of the root port (see: PCH_PCIE_ASPM_CONTROL). Default is
PchPcieAspmAutoConfig.
**/
UINT8 PcieRpAspm[29];
/** Offset 0x09E0 - PCIE RP L1 Substates
The L1 Substates configuration of the root port (see: PCH_PCIE_L1SUBSTATES_CONTROL).
Default is PchPcieL1SubstatesL1_1_2.
**/
UINT8 PcieRpL1Substates[29];
/** Offset 0x09FD - PCIE RP Ltr Enable
Latency Tolerance Reporting Mechanism.
**/
UINT8 PcieRpLtrEnable[29];
/** Offset 0x0A1A - PCIE RP Ltr Config Lock
0: Disable; 1: Enable.
**/
UINT8 PcieRpLtrConfigLock[29];
/** Offset 0x0A37 - PCIE RP override default settings for EQ
Choose PCIe EQ method
$EN_DIS
**/
UINT8 PcieEqOverrideDefault[29];
/** Offset 0x0A54 - PCIE RP choose EQ method
Choose PCIe EQ method
0: HardwareEq, 1: FixedEq
**/
UINT8 PcieGen3EqMethod[29];
/** Offset 0x0A71 - PCIE RP choose EQ mode
Choose PCIe EQ mode
0: PresetEq, 1: CoefficientEq
**/
UINT8 PcieGen3EqMode[29];
/** Offset 0x0A8E - PCIE RP EQ local transmitter override
Enable/Disable local transmitter override
$EN_DIS
**/
UINT8 PcieGen3EqLocalTxOverrideEn[29];
/** Offset 0x0AAB - PCI RP number of valid list entries
Select number of presets or coefficients depending on the mode
**/
UINT8 PcieGen3EqPh3NoOfPresetOrCoeff[29];
/** Offset 0x0AC8 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PreCursor0List[29];
/** Offset 0x0AE5 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PostCursor0List[29];
/** Offset 0x0B02 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PreCursor1List[29];
/** Offset 0x0B1F - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PostCursor1List[29];
/** Offset 0x0B3C - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PreCursor2List[29];
/** Offset 0x0B59 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PostCursor2List[29];
/** Offset 0x0B76 - PCIR RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PreCursor3List[29];
/** Offset 0x0B93 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PostCursor3List[29];
/** Offset 0x0BB0 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PreCursor4List[29];
/** Offset 0x0BCD - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PostCursor4List[29];
/** Offset 0x0BEA - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PreCursor5List[29];
/** Offset 0x0C07 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PostCursor5List[29];
/** Offset 0x0C24 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PreCursor6List[29];
/** Offset 0x0C41 - PCIe post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PostCursor6List[29];
/** Offset 0x0C5E - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PreCursor7List[29];
/** Offset 0x0C7B - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PostCursor7List[29];
/** Offset 0x0C98 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PreCursor8List[29];
/** Offset 0x0CB5 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PostCursor8List[29];
/** Offset 0x0CD2 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PreCursor9List[29];
/** Offset 0x0CEF - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3PostCursor9List[29];
/** Offset 0x0D0C - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset0List[29];
/** Offset 0x0D29 - PCIe preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset1List[29];
/** Offset 0x0D46 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset2List[29];
/** Offset 0x0D63 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset3List[29];
/** Offset 0x0D80 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset4List[29];
/** Offset 0x0D9D - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset5List[29];
/** Offset 0x0DBA - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset6List[29];
/** Offset 0x0DD7 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset7List[29];
/** Offset 0x0DF4 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset8List[29];
/** Offset 0x0E11 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset9List[29];
/** Offset 0x0E2E - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen3EqPh3Preset10List[29];
/** Offset 0x0E4B - PCIe EQ phase 1 downstream transmitter port preset
Allows to select the downstream port preset value that will be used during phase
1 of equalization
**/
UINT8 PcieGen3EqPh1DpTxPreset[29];
/** Offset 0x0E68 - PCIE RP EQ phase 1 upstream tranmitter port preset
Allows to select the upstream port preset value that will be used during phase 1
of equalization
**/
UINT8 PcieGen3EqPh1UpTxPreset[29];
/** Offset 0x0E85 - PCIE RP EQ phase 2 local transmitter override preset
Allows to select the value of the preset used during phase 2 local transmitter override
**/
UINT8 PcieGen3EqPh2LocalTxOverridePreset[29];
/** Offset 0x0EA2 - PCIE RP choose EQ method
Choose PCIe EQ method
0: HardwareEq, 1: FixedEq
**/
UINT8 PcieGen4EqMethod[29];
/** Offset 0x0EBF - PCIE RP choose EQ mode
Choose PCIe EQ mode
0: PresetEq, 1: CoefficientEq
**/
UINT8 PcieGen4EqMode[29];
/** Offset 0x0EDC - PCIE RP EQ local transmitter override
Enable/Disable local transmitter override
$EN_DIS
**/
UINT8 PcieGen4EqLocalTxOverrideEn[29];
/** Offset 0x0EF9 - PCI RP number of valid list entries
Select number of presets or coefficients depending on the mode
**/
UINT8 PcieGen4EqPh3NoOfPresetOrCoeff[29];
/** Offset 0x0F16 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PreCursor0List[29];
/** Offset 0x0F33 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PostCursor0List[29];
/** Offset 0x0F50 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PreCursor1List[29];
/** Offset 0x0F6D - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PostCursor1List[29];
/** Offset 0x0F8A - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PreCursor2List[29];
/** Offset 0x0FA7 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PostCursor2List[29];
/** Offset 0x0FC4 - PCIR RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PreCursor3List[29];
/** Offset 0x0FE1 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PostCursor3List[29];
/** Offset 0x0FFE - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PreCursor4List[29];
/** Offset 0x101B - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PostCursor4List[29];
/** Offset 0x1038 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PreCursor5List[29];
/** Offset 0x1055 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PostCursor5List[29];
/** Offset 0x1072 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PreCursor6List[29];
/** Offset 0x108F - PCIe post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PostCursor6List[29];
/** Offset 0x10AC - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PreCursor7List[29];
/** Offset 0x10C9 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PostCursor7List[29];
/** Offset 0x10E6 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PreCursor8List[29];
/** Offset 0x1103 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PostCursor8List[29];
/** Offset 0x1120 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PreCursor9List[29];
/** Offset 0x113D - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3PostCursor9List[29];
/** Offset 0x115A - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset0List[29];
/** Offset 0x1177 - PCIe preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset1List[29];
/** Offset 0x1194 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset2List[29];
/** Offset 0x11B1 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset3List[29];
/** Offset 0x11CE - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset4List[29];
/** Offset 0x11EB - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset5List[29];
/** Offset 0x1208 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset6List[29];
/** Offset 0x1225 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset7List[29];
/** Offset 0x1242 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset8List[29];
/** Offset 0x125F - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset9List[29];
/** Offset 0x127C - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen4EqPh3Preset10List[29];
/** Offset 0x1299 - PCIe EQ phase 1 downstream transmitter port preset
Allows to select the downstream port preset value that will be used during phase
1 of equalization
**/
UINT8 PcieGen4EqPh1DpTxPreset[29];
/** Offset 0x12B6 - PCIE RP EQ phase 1 upstream tranmitter port preset
Allows to select the upstream port preset value that will be used during phase 1
of equalization
**/
UINT8 PcieGen4EqPh1UpTxPreset[29];
/** Offset 0x12D3 - PCIE RP EQ phase 2 local transmitter override preset
Allows to select the value of the preset used during phase 2 local transmitter override
**/
UINT8 PcieGen4EqPh2LocalTxOverridePreset[29];
/** Offset 0x12F0 - PCIE RP choose EQ method
Choose PCIe EQ method
0: HardwareEq, 1: FixedEq
**/
UINT8 PcieGen5EqMethod[29];
/** Offset 0x130D - PCIE RP choose EQ mode
Choose PCIe EQ mode
0: PresetEq, 1: CoefficientEq
**/
UINT8 PcieGen5EqMode[29];
/** Offset 0x132A - PCIE RP EQ local transmitter override
Enable/Disable local transmitter override
$EN_DIS
**/
UINT8 PcieGen5EqLocalTxOverrideEn[29];
/** Offset 0x1347 - PCI RP number of valid list entries
Select number of presets or coefficients depending on the mode
**/
UINT8 PcieGen5EqPh3NoOfPresetOrCoeff[29];
/** Offset 0x1364 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PreCursor0List[29];
/** Offset 0x1381 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PostCursor0List[29];
/** Offset 0x139E - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PreCursor1List[29];
/** Offset 0x13BB - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PostCursor1List[29];
/** Offset 0x13D8 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PreCursor2List[29];
/** Offset 0x13F5 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PostCursor2List[29];
/** Offset 0x1412 - PCIR RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PreCursor3List[29];
/** Offset 0x142F - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PostCursor3List[29];
/** Offset 0x144C - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PreCursor4List[29];
/** Offset 0x1469 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PostCursor4List[29];
/** Offset 0x1486 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PreCursor5List[29];
/** Offset 0x14A3 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PostCursor5List[29];
/** Offset 0x14C0 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PreCursor6List[29];
/** Offset 0x14DD - PCIe post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PostCursor6List[29];
/** Offset 0x14FA - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PreCursor7List[29];
/** Offset 0x1517 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PostCursor7List[29];
/** Offset 0x1534 - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PreCursor8List[29];
/** Offset 0x1551 - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PostCursor8List[29];
/** Offset 0x156E - PCIE RP pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PreCursor9List[29];
/** Offset 0x158B - PCIE RP post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3PostCursor9List[29];
/** Offset 0x15A8 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset0List[29];
/** Offset 0x15C5 - PCIe preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset1List[29];
/** Offset 0x15E2 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset2List[29];
/** Offset 0x15FF - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset3List[29];
/** Offset 0x161C - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset4List[29];
/** Offset 0x1639 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset5List[29];
/** Offset 0x1656 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset6List[29];
/** Offset 0x1673 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset7List[29];
/** Offset 0x1690 - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset8List[29];
/** Offset 0x16AD - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset9List[29];
/** Offset 0x16CA - PCIE RP preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieGen5EqPh3Preset10List[29];
/** Offset 0x16E7 - PCIe EQ phase 1 downstream transmitter port preset
Allows to select the downstream port preset value that will be used during phase
1 of equalization
**/
UINT8 PcieGen5EqPh1DpTxPreset[29];
/** Offset 0x1704 - PCIE RP EQ phase 1 upstream tranmitter port preset
Allows to select the upstream port preset value that will be used during phase 1
of equalization
**/
UINT8 PcieGen5EqPh1UpTxPreset[29];
/** Offset 0x1721 - PCIE RP EQ phase 2 local transmitter override preset
Allows to select the value of the preset used during phase 2 local transmitter override
**/
UINT8 PcieGen5EqPh2LocalTxOverridePreset[29];
/** Offset 0x173E - Phase3 RP Gen3 EQ enable
Phase3 Gen3 EQ enable. Disabled(0x0)(Default): Disable phase 3, Enabled(0x1): Enable phase 3
0:Disable, 1:Enable, 2:Auto
**/
UINT8 PcieRpGen3EqPh3Bypass[29];
/** Offset 0x175B - Phase3 RP Gen3 EQ enable
Phase3 Gen3 EQ enable. Disabled(0x0)(Default): Disable phase 3, Enabled(0x1): Enable phase 3
0:Disable, 1:Enable, 2:Auto
**/
UINT8 PcieRpGen4EqPh3Bypass[29];
/** Offset 0x1778 - Phase3 RP Gen5 EQ enable
Phase3 Gen5 EQ enable. Disabled(0x0)(Default): Disable phase 3, Enabled(0x1): Enable phase 3
0:Disable, 1:Enable, 2:Auto
**/
UINT8 PcieRpGen5EqPh3Bypass[29];
/** Offset 0x1795 - Phase2-3 RP Gen3 EQ enable
Phase2-3 Gen3 EQ enable. Disabled(0x0)(Default): Disable Phase2-3, Enabled(0x1):
Enable Phase2-3
0:Disable, 1:Enable, 2:Auto
**/
UINT8 PcieRpGen3EqPh23Bypass[29];
/** Offset 0x17B2 - Phase2-3 RP Gen4 EQ enable
Phase2-3 Gen4 EQ enable. Disabled(0x0)(Default): Disable Phase2-3, Enabled(0x1):
Enable Phase2-3
0:Disable, 1:Enable, 2:Auto
**/
UINT8 PcieRpGen4EqPh23Bypass[29];
/** Offset 0x17CF - Phase2-3 RP Gen5 EQ enable
Phase2-3 Gen5 EQ enable. Disabled(0x0)(Default): Disable Phase2-3, Enabled(0x1):
Enable Phase2-3
0:Disable, 1:Enable, 2:Auto
**/
UINT8 PcieRpGen5EqPh23Bypass[29];
/** Offset 0x17EC - RP Gen3 EQ Phase enable
Gen3 EQ Phase enable. Disabled(0x0)(Default): Disable Eq Phase, Enabled(0x1): Enable Eq Phase
0:Disable, 1:Enable, 2:Auto
**/
UINT8 PcieRpGen3EqPhBypass[29];
/** Offset 0x1809 - RP Gen4 EQ Phase enable
Gen4 EQ Phase enable. Disabled(0x0)(Default): Disable Eq Phase, Enabled(0x1): Enable Eq Phase
0:Disable, 1:Enable, 2:Auto
**/
UINT8 PcieRpGen4EqPhBypass[29];
/** Offset 0x1826 - RP Gen5 EQ Phase enable
Gen5 EQ Phase enable. Disabled(0x0)(Default): Disable Eq Phase, Enabled(0x1): Enable Eq Phase
0:Disable, 1:Enable, 2:Auto
**/
UINT8 PcieRpGen5EqPhBypass[29];
/** Offset 0x1843 - PCET Timer
Preset/Coefficient Evaluation Timeout Gen3 PCET Timer. See PCIE_GEN3_PCET. Default
is 0x0(2ms)
**/
UINT8 PcieGen3PcetTimer[29];
/** Offset 0x1860 - Gen4 PCET Timer
Preset/Coefficient Evaluation Timeout - Gen4 PCET Timer. See PCIE_GEN4_PCET. Default
is 0x0(2ms)
**/
UINT8 PcieGen4PcetTimer[29];
/** Offset 0x187D - Gen5 PCET Timer
Preset/Coefficient Evaluation Timeout - Gen5 PCET Timer. See PCIE_GEN5_PCET. Default
is 0x0(2ms)
**/
UINT8 PcieGen5PcetTimer[29];
/** Offset 0x189A - TS Lock Timer for Gen3
Training Sequence Wait Latency For Presets/Coefficients Evaluation - Gen3 TS Lock
Timer. See PCIE_GEN3_TS_LOCK_TIMER. Default is 0x0
**/
UINT8 PcieGen3TsLockTimer[29];
/** Offset 0x18B7 - PTS Lock Timer for Gen4
Training Sequence Wait Latency For Presets/Coefficients Evaluation - Gen4 TS Lock
Timer. See PCIE_GEN4_TS_LCOK_TIMER. Default is 0x0
**/
UINT8 PcieGen4TsLockTimer[29];
/** Offset 0x18D4 - PTS Lock Timer for Gen5
Training Sequence Wait Latency For Presets/Coefficients Evaluation - Gen5 TS Lock
Timer. See PCIE_GEN5_TS_LCOK_TIMER. Default is 0x0
**/
UINT8 PcieGen5TsLockTimer[29];
/** Offset 0x18F1 - PCIE Secure Register Lock
Describes whether Secure Register Lock is enaled or disabled. When it will be enbaled,
load PcieRpSetSecuredRegisterLock recipe. 0: Disable(Default); 1: Enable
$EN_DIS
**/
UINT8 PcieSetSecuredRegisterLock;
/** Offset 0x18F2 - DG Wait
0(Default) = Disable, 1 = Enable
$EN_DIS
**/
UINT8 DGWait;
/** Offset 0x18F3 - Enable/Disable ASPM Optionality Compliance
Enable/Disable ASPM Optionality Compliance.
**/
UINT8 PcieRpTestAspmOc[12];
/** Offset 0x18FF - PCIe Configuration Dump
Enable/Disable ASPM Optionality Compliance.
0:Disable, 1:Enable
**/
UINT8 PcieCfgDump[12];
/** Offset 0x190B - PCIE RP Enable Peer Memory Write
This member describes whether Peer Memory Writes are enabled on the platform.
$EN_DIS
**/
UINT8 PcieEnablePeerMemoryWrite[12];
/** Offset 0x1917 - PCIE Compliance Test Mode
Compliance Test Mode shall be enabled when using Compliance Load Board.
$EN_DIS
**/
UINT8 PcieComplianceTestMode;
/** Offset 0x1918 - PCIE Rp Function Swap
Allows BIOS to use root port function number swapping when root port of function
0 is disabled.
$EN_DIS
**/
UINT8 PcieRpFunctionSwap;
/** Offset 0x1919 - PCIe Fia Programming
Load Fia configuration if enable. 0: Disable; 1: Enable(Default).
$EN_DIS
**/
UINT8 PcieFiaProgramming;
/** Offset 0x191A - PCH Pm PME_B0_S5_DIS
When cleared (default), wake events from PME_B0_STS are allowed in S5 if PME_B0_EN = 1.
$EN_DIS
**/
UINT8 PchPmPmeB0S5Dis;
/** Offset 0x191B - PCIE IMR
Enables Isolated Memory Region for PCIe.
$EN_DIS
**/
UINT8 PcieRpImrEnabled;
/** Offset 0x191C - PCIE IMR port number
Selects PCIE root port number for IMR feature.
**/
UINT8 PcieRpImrSelection;
/** Offset 0x191D - PCH Pm Wol Enable Override
Corresponds to the WOL Enable Override bit in the General PM Configuration B (GEN_PMCON_B) register.
$EN_DIS
**/
UINT8 PchPmWolEnableOverride;
/** Offset 0x191E - PCH Pm WoW lan Enable
Determine if WLAN wake from Sx, corresponds to the HOST_WLAN_PP_EN bit in the PWRM_CFG3 register.
$EN_DIS
**/
UINT8 PchPmWoWlanEnable;
/** Offset 0x191F - PCH Pm WoW lan DeepSx Enable
Determine if WLAN wake from DeepSx, corresponds to the DSX_WLAN_PP_EN bit in the
PWRM_CFG3 register.
$EN_DIS
**/
UINT8 PchPmWoWlanDeepSxEnable;
/** Offset 0x1920 - PCH Pm Lan Wake From DeepSx
Determine if enable LAN to wake from deep Sx.
$EN_DIS
**/
UINT8 PchPmLanWakeFromDeepSx;
/** Offset 0x1921 - PCH Pm Deep Sx Pol
Deep Sx Policy.
$EN_DIS
**/
UINT8 PchPmDeepSxPol;
/** Offset 0x1922 - PCH Pm Disable Dsx Ac Present Pulldown
When Disable, PCH will internal pull down AC_PRESENT in deep SX and during G3 exit.
$EN_DIS
**/
UINT8 PchPmDisableDsxAcPresentPulldown;
/** Offset 0x1923 - PCH Pm Slp S3 Min Assert
SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms.
**/
UINT8 PchPmSlpS3MinAssert;
/** Offset 0x1924 - PCH Pm Slp S4 Min Assert
SLP_S4 Minimum Assertion Width Policy. Default is PchSlpS44s.
**/
UINT8 PchPmSlpS4MinAssert;
/** Offset 0x1925 - PCH Pm Slp Sus Min Assert
SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s.
**/
UINT8 PchPmSlpSusMinAssert;
/** Offset 0x1926 - PCH Pm Slp A Min Assert
SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s.
**/
UINT8 PchPmSlpAMinAssert;
/** Offset 0x1927 - USB Overcurrent Override for VISA
This option overrides USB Over Current enablement state that USB OC will be disabled
after enabling this option. Enable when VISA pin is muxed with USB OC
$EN_DIS
**/
UINT8 PchEnableDbcObs;
/** Offset 0x1928 - PCH Pm Slp Strch Sus Up
Enable SLP_X Stretching After SUS Well Power Up.
$EN_DIS
**/
UINT8 PchPmSlpStrchSusUp;
/** Offset 0x1929 - PCH Pm Slp Lan Low Dc
Enable/Disable SLP_LAN# Low on DC Power.
$EN_DIS
**/
UINT8 PchPmSlpLanLowDc;
/** Offset 0x192A - PCH Pm Pwr Btn Override Period
PCH power button override period. 000b-4s, 001b-6s, 010b-8s, 011b-10s, 100b-12s, 101b-14s.
**/
UINT8 PchPmPwrBtnOverridePeriod;
/** Offset 0x192B - PCH Pm Disable Native Power Button
Power button native mode disable.
$EN_DIS
**/
UINT8 PchPmDisableNativePowerButton;
/** Offset 0x192C - PCH Pm ME_WAKE_STS
Clear the ME_WAKE_STS bit in the Power and Reset Status (PRSTS) register.
$EN_DIS
**/
UINT8 PchPmMeWakeSts;
/** Offset 0x192D - PCH Pm WOL_OVR_WK_STS
Clear the WOL_OVR_WK_STS bit in the Power and Reset Status (PRSTS) register.
$EN_DIS
**/
UINT8 PchPmWolOvrWkSts;
/** Offset 0x192E - PCH Pm Reset Power Cycle Duration
Could be customized in the unit of second. Please refer to EDS for all support settings.
0 is default, 1 is 1 second, 2 is 2 seconds, ...
**/
UINT8 PchPmPwrCycDur;
/** Offset 0x192F - PCH Pm Pcie Pll Ssc
Specifies the Pcie Pll Spread Spectrum Percentage. The default is 0xFF: AUTO - No
BIOS override.
**/
UINT8 PchPmPciePllSsc;
/** Offset 0x1930 - PCH Legacy IO Low Latency Enable
Set to enable low latency of legacy IO. 0: Disable, 1: Enable
$EN_DIS
**/
UINT8 PchLegacyIoLowLatency;
/** Offset 0x1931 - PCH Sata Pwr Opt Enable
SATA Power Optimizer on PCH side.
$EN_DIS
**/
UINT8 SataPwrOptEnable;
/** Offset 0x1932 - PCH Sata eSATA Speed Limit
When enabled, BIOS will configure the PxSCTL.SPD to 2 to limit the eSATA port speed.
$EN_DIS
**/
UINT8 EsataSpeedLimit;
/** Offset 0x1933 - PCH Sata Speed Limit
Indicates the maximum speed the SATA controller can support 0h: PchSataSpeedDefault.
**/
UINT8 SataSpeedLimit;
/** Offset 0x1934 - Enable SATA Port HotPlug
Enable SATA Port HotPlug.
**/
UINT8 SataPortsHotPlug[8];
/** Offset 0x193C - Enable SATA Port Interlock Sw
Enable SATA Port Interlock Sw.
**/
UINT8 SataPortsInterlockSw[8];
/** Offset 0x1944 - Enable SATA Port External
Enable SATA Port External.
**/
UINT8 SataPortsExternal[8];
/** Offset 0x194C - Enable SATA Port SpinUp
Enable the COMRESET initialization Sequence to the device.
**/
UINT8 SataPortsSpinUp[8];
/** Offset 0x1954 - Enable SATA Port Solid State Drive
0: HDD; 1: SSD.
**/
UINT8 SataPortsSolidStateDrive[8];
/** Offset 0x195C - Enable SATA Port Enable Dito Config
Enable DEVSLP Idle Timeout settings (DmVal, DitoVal).
**/
UINT8 SataPortsEnableDitoConfig[8];
/** Offset 0x1964 - Enable SATA Port DmVal
DITO multiplier. Default is 15.
**/
UINT8 SataPortsDmVal[8];
/** Offset 0x196C - Pch Dmi Aspm Ctrl
ASPM configuration on the PCH side of the DMI/OPI Link. Default is PchPcieAspmAutoConfig
0:Disabled, 1:L0s, 2:L1, 3:L0sL1, 4:Auto
**/
UINT8 PchDmiAspm;
/** Offset 0x196D
**/
UINT8 Rsvd300[1];
/** Offset 0x196E - Enable SATA Port DmVal
DEVSLP Idle Timeout (DITO), Default is 625.
**/
UINT16 SataPortsDitoVal[8];
/** Offset 0x197E - Enable SATA Port ZpOdd
Support zero power ODD.
**/
UINT8 SataPortsZpOdd[8];
/** Offset 0x1986 - PCH Sata Rst Raid Alternate Id
Enable RAID Alternate ID.
$EN_DIS
**/
UINT8 SataRstRaidDeviceId;
/** Offset 0x1987 - PCH Sata Rst Pcie Storage Remap enable
Enable Intel RST for PCIe Storage remapping.
**/
UINT8 SataRstPcieEnable[3];
/** Offset 0x198A - PCH Sata Rst Pcie Storage Port
Intel RST for PCIe Storage remapping - PCIe Port Selection (1-based, 0 = autodetect).
**/
UINT8 SataRstPcieStoragePort[3];
/** Offset 0x198D - PCH Sata Rst Pcie Device Reset Delay
PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms
**/
UINT8 SataRstPcieDeviceResetDelay[3];
/** Offset 0x1990 - UFS enable/disable
Enable/Disable UFS controller, One byte for each Controller - (1,0) to enable controller
0 and (0,1) to enable controller 1
$EN_DIS
**/
UINT8 UfsEnable[2];
/** Offset 0x1992 - UFS Inline Encryption enable/disable
Enable/Disable UFS Inline Encryption feature, One byte for each Controller - (1,0)
to enable Inline Encryption for controller 0 and (0,1) to enable Inline Encryption
for controller 1
$EN_DIS
**/
UINT8 UfsInlineEncryption[2];
/** Offset 0x1994 - IEH Mode
Integrated Error Handler Mode, 0: Bypass, 1: Enable
0: Bypass, 1:Enable
**/
UINT8 IehMode;
/** Offset 0x1995 - SOC Thermal Throttling Suggested Setting
Thermal Throttling Suggested Setting. When it is enabled, customized throttle levels
are ignored but with native settings.
$EN_DIS
**/
UINT8 SocTTSuggestedSetting;
/** Offset 0x1996 - SOC Thermal Throttling Custimized T0Level Value
Custimized T0Level value.
**/
UINT16 SocT0Level;
/** Offset 0x1998 - SOC Thermal Throttling Custimized T1Level Value
Custimized T1Level value.
**/
UINT16 SocT1Level;
/** Offset 0x199A - SOC Thermal Throttling Custimized T2Level Value
Custimized T2Level value.
**/
UINT16 SocT2Level;
/** Offset 0x199C - Enable SOC Thermal Throttle
Enable thermal throttle function.
$EN_DIS
**/
UINT8 SocTTEnable;
/** Offset 0x199D - SOC PMSync State 13
When set to 1 and the programmed GPIO pin is a 1, then PMSync state 13 will force
at least T2 state.
$EN_DIS
**/
UINT8 SocTTState13Enable;
/** Offset 0x199E - SOC Thermal Throttle Lock
Thermal Throttle Lock.
$EN_DIS
**/
UINT8 SocTTLock;
/** Offset 0x199F - PCH Thermal Throttling Suggested Setting
Thermal Throttling Suggested Setting. When it is enabled, customized throttle levels
are ignored but with native settings.
$EN_DIS
**/
UINT8 PchTTSuggestedSetting;
/** Offset 0x19A0 - PCH Thermal Throttling Custimized T0Level Value
Custimized T0Level value.
**/
UINT16 PchT0Level;
/** Offset 0x19A2 - PCH Thermal Throttling Custimized T1Level Value
Custimized T1Level value.
**/
UINT16 PchT1Level;
/** Offset 0x19A4 - PCH Thermal Throttling Custimized T2Level Value
Custimized T2Level value.
**/
UINT16 PchT2Level;
/** Offset 0x19A6 - Enable PCH Thermal Throttle
Enable thermal throttle function.
$EN_DIS
**/
UINT8 PchTTEnable;
/** Offset 0x19A7 - PCH PMSync State 13
When set to 1 and the programmed GPIO pin is a 1, then PMSync state 13 will force
at least T2 state.
$EN_DIS
**/
UINT8 PchTTState13Enable;
/** Offset 0x19A8 - PCH Thermal Throttle Lock
Thermal Throttle Lock.
$EN_DIS
**/
UINT8 PchTTLock;
/** Offset 0x19A9 - IOE Thermal Throttling Suggested Setting
IOE Thermal Throttling Suggested Setting. When it is enabled, customized throttle
levels are ignored but with native settings.
$EN_DIS
**/
UINT8 IoeTTSuggestedSetting;
/** Offset 0x19AA - IOE Thermal Throttling Custimized T0Level Value
Custimized IOE T0Level value.
**/
UINT16 IoeT0Level;
/** Offset 0x19AC - IOE Thermal Throttling Custimized T1Level Value
Custimized IOE T1Level value.
**/
UINT16 IoeT1Level;
/** Offset 0x19AE - IOE Thermal Throttling Custimized T2Level Value
Custimized IOE T2Level value.
**/
UINT16 IoeT2Level;
/** Offset 0x19B0 - Enable IOE Thermal Throttle
Enable thermal throttle function.
$EN_DIS
**/
UINT8 IoeTTEnable;
/** Offset 0x19B1 - IOE Thermal Throttle Lock
Thermal Throttle Lock.
$EN_DIS
**/
UINT8 IoeTTLock;
/** Offset 0x19B2 - DMI Thermal Sensor Autonomous Width Enable
DMI Thermal Sensor Autonomous Width Enable.
$EN_DIS
**/
UINT8 PchDmiTsawEn;
/** Offset 0x19B3 - DMI Thermal Sensor Suggested Setting
DMT thermal sensor suggested representative values.
$EN_DIS
**/
UINT8 DmiSuggestedSetting;
/** Offset 0x19B4 - Thermal Sensor 0 Target Width
Thermal Sensor 0 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS0TW;
/** Offset 0x19B5 - Thermal Sensor 1 Target Width
Thermal Sensor 1 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS1TW;
/** Offset 0x19B6 - Thermal Sensor 2 Target Width
Thermal Sensor 2 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS2TW;
/** Offset 0x19B7 - Thermal Sensor 3 Target Width
Thermal Sensor 3 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS3TW;
/** Offset 0x19B8 - Port 0 T1 Multipler
Port 0 T1 Multipler.
**/
UINT8 SataP0T1M;
/** Offset 0x19B9 - Port 0 T2 Multipler
Port 0 T2 Multipler.
**/
UINT8 SataP0T2M;
/** Offset 0x19BA - Port 0 T3 Multipler
Port 0 T3 Multipler.
**/
UINT8 SataP0T3M;
/** Offset 0x19BB - Port 0 Tdispatch
Port 0 Tdispatch.
**/
UINT8 SataP0TDisp;
/** Offset 0x19BC - Port 1 T1 Multipler
Port 1 T1 Multipler.
**/
UINT8 SataP1T1M;
/** Offset 0x19BD - Port 1 T2 Multipler
Port 1 T2 Multipler.
**/
UINT8 SataP1T2M;
/** Offset 0x19BE - Port 1 T3 Multipler
Port 1 T3 Multipler.
**/
UINT8 SataP1T3M;
/** Offset 0x19BF - Port 1 Tdispatch
Port 1 Tdispatch.
**/
UINT8 SataP1TDisp;
/** Offset 0x19C0 - Port 0 Tinactive
Port 0 Tinactive.
**/
UINT8 SataP0Tinact;
/** Offset 0x19C1 - Port 0 Alternate Fast Init Tdispatch
Port 0 Alternate Fast Init Tdispatch.
$EN_DIS
**/
UINT8 SataP0TDispFinit;
/** Offset 0x19C2 - Port 1 Tinactive
Port 1 Tinactive.
**/
UINT8 SataP1Tinact;
/** Offset 0x19C3 - Port 1 Alternate Fast Init Tdispatch
Port 1 Alternate Fast Init Tdispatch.
$EN_DIS
**/
UINT8 SataP1TDispFinit;
/** Offset 0x19C4 - Sata Thermal Throttling Suggested Setting
Sata Thermal Throttling Suggested Setting.
$EN_DIS
**/
UINT8 SataThermalSuggestedSetting;
/** Offset 0x19C5
**/
UINT8 Rsvd310;
/** Offset 0x19C6 - Thermal Device Temperature
Decides the temperature.
**/
UINT16 PchTemperatureHotLevel;
/** Offset 0x19C8 - USB2 Port Over Current Pin
Describe the specific over current pin number of USB 2.0 Port N.
**/
UINT8 Usb2OverCurrentPin[16];
/** Offset 0x19D8 - USB3 Port Over Current Pin
Describe the specific over current pin number of USB 3.0 Port N.
**/
UINT8 Usb3OverCurrentPin[10];
/** Offset 0x19E2 - Enable xHCI LTR override
Enables override of recommended LTR values for xHCI
$EN_DIS
**/
UINT8 PchUsbLtrOverrideEnable;
/** Offset 0x19E3
**/
UINT8 Rsvd320[1];
/** Offset 0x19E4 - xHCI High Idle Time LTR override
Value used for overriding LTR recommendation for xHCI High Idle Time LTR setting
**/
UINT32 PchUsbLtrHighIdleTimeOverride;
/** Offset 0x19E8 - xHCI Medium Idle Time LTR override
Value used for overriding LTR recommendation for xHCI Medium Idle Time LTR setting
**/
UINT32 PchUsbLtrMediumIdleTimeOverride;
/** Offset 0x19EC - xHCI Low Idle Time LTR override
Value used for overriding LTR recommendation for xHCI Low Idle Time LTR setting
**/
UINT32 PchUsbLtrLowIdleTimeOverride;
/** Offset 0x19F0 - Enable 8254 Static Clock Gating
Set 8254CGE=1 is required for SLP_S0 support. However, set 8254CGE=1 in POST time
might fail to boot legacy OS using 8254 timer. Make sure it is disabled to support
legacy OS using 8254 timer. Also enable this while S0ix is enabled.
$EN_DIS
**/
UINT8 Enable8254ClockGating;
/** Offset 0x19F1 - Enable 8254 Static Clock Gating On S3
This is only applicable when Enable8254ClockGating is disabled. FSP will do the
8254 CGE programming on S3 resume when Enable8254ClockGatingOnS3 is enabled. This
avoids the SMI requirement for the programming.
$EN_DIS
**/
UINT8 Enable8254ClockGatingOnS3;
/** Offset 0x19F2 - Enable TCO timer.
When FALSE, it disables PCH ACPI timer, and stops TCO timer. NOTE: This will have
huge power impact when it's enabled. If TCO timer is disabled, uCode ACPI timer
emulation must be enabled, and WDAT table must not be exposed to the OS.
$EN_DIS
**/
UINT8 EnableTcoTimer;
/** Offset 0x19F3
**/
UINT8 Rsvd330[5];
/** Offset 0x19F8 - BgpdtHash[4]
BgpdtHash values
**/
UINT64 BgpdtHash[4];
/** Offset 0x1A18 - BiosGuardAttr
BiosGuardAttr default values
**/
UINT32 BiosGuardAttr;
/** Offset 0x1A1C
**/
UINT8 Rsvd340[4];
/** Offset 0x1A20 - BiosGuardModulePtr
BiosGuardModulePtr default values
**/
UINT64 BiosGuardModulePtr;
/** Offset 0x1A28 - SendEcCmd
SendEcCmd function pointer. \n
@code typedef EFI_STATUS (EFIAPI *PLATFORM_SEND_EC_COMMAND) (IN EC_COMMAND_TYPE
EcCmdType, IN UINT8 EcCmd, IN UINT8 SendData, IN OUT UINT8 *ReceiveData); @endcode
**/
UINT64 SendEcCmd;
/** Offset 0x1A30 - EcCmdProvisionEav
Ephemeral Authorization Value default values. Provisions an ephemeral shared secret to the EC
**/
UINT8 EcCmdProvisionEav;
/** Offset 0x1A31 - EcCmdLock
EcCmdLock default values. Locks Ephemeral Authorization Value sent previously
**/
UINT8 EcCmdLock;
/** Offset 0x1A32
**/
UINT8 Rsvd350[6];
/** Offset 0x1A38 - EcProvisionEav
EcProvisionEav function pointer. \n
@code typedef EFI_STATUS (EFIAPI *EC_PROVISION_EAV) (IN UINT32 Eav, OUT UINT8
*ReturnValue); @endcode
**/
UINT64 EcProvisionEav;
/** Offset 0x1A40 - EcBiosGuardCmdLock
EcBiosGuardCmdLock function pointer. \n
@code typedef EFI_STATUS (EFIAPI *EC_CMD_LOCK) (OUT UINT8 *ReturnValue); @endcode
**/
UINT64 EcBiosGuardCmdLock;
/** Offset 0x1A48 - Skip Ssid Programming.
When set to TRUE, silicon code will not do any SSID programming and platform code
needs to handle that by itself properly.
$EN_DIS
**/
UINT8 SiSkipSsidProgramming;
/** Offset 0x1A49
**/
UINT8 Rsvd360;
/** Offset 0x1A4A - Change Default SVID
Change the default SVID used in FSP to programming internal devices. This is only
valid when SkipSsidProgramming is FALSE.
**/
UINT16 SiCustomizedSvid;
/** Offset 0x1A4C - Change Default SSID
Change the default SSID used in FSP to programming internal devices. This is only
valid when SkipSsidProgramming is FALSE.
**/
UINT16 SiCustomizedSsid;
/** Offset 0x1A4E
**/
UINT8 Rsvd370[2];
/** Offset 0x1A50 - SVID SDID table Poniter.
The address of the table of SVID SDID to customize each SVID SDID entry. This is
only valid when SkipSsidProgramming is FALSE.
**/
UINT32 SiSsidTablePtr;
/** Offset 0x1A54 - Number of ssid table.
SiNumberOfSsidTableEntry should match the table entries created in SiSsidTablePtr.
This is only valid when SkipSsidProgramming is FALSE.
**/
UINT16 SiNumberOfSsidTableEntry;
/** Offset 0x1A56 - USB2 Port Reset Message Enable
0: Disable USB2 Port Reset Message; 1: Enable USB2 Port Reset Message; This must
be enable for USB2 Port those are paired with CPU XHCI Port
**/
UINT8 PortResetMessageEnable[16];
/** Offset 0x1A66 - SATA RST Interrupt Mode
Allowes to choose which interrupts will be implemented by SATA controller in RAID mode.
0:Msix, 1:Msi, 2:Legacy
**/
UINT8 SataRstInterrupt;
/** Offset 0x1A67 - Enable PS_ON.
PS_ON is a new C10 state from the CPU on desktop SKUs that enables a lower power
target that will be required by the California Energy Commission (CEC). When FALSE,
PS_ON is to be disabled.
$EN_DIS
**/
UINT8 PsOnEnable;
/** Offset 0x1A68 - Pmc Cpu C10 Gate Pin Enable
Enable/Disable platform support for CPU_C10_GATE# pin to control gating of CPU VccIO
and VccSTG rails instead of SLP_S0# pin.
$EN_DIS
**/
UINT8 PmcCpuC10GatePinEnable;
/** Offset 0x1A69 - Pch Dmi Aspm Ctrl
ASPM configuration on the PCH side of the DMI/OPI Link. Default is PchPcieAspmAutoConfig
0:Disabled, 1:L0s, 2:L1, 3:L0sL1, 4:Auto
**/
UINT8 PchDmiAspmCtrl;
/** Offset 0x1A6A - PchDmiCwbEnable
Central Write Buffer feature configurable and enabled by default
$EN_DIS
**/
UINT8 PchDmiCwbEnable;
/** Offset 0x1A6B - OS IDLE Mode Enable
Enable/Disable OS Idle Mode
$EN_DIS
**/
UINT8 PmcOsIdleEnable;
/** Offset 0x1A6C - S0ix Auto-Demotion
Enable/Disable the Low Power Mode Auto-Demotion Host Control feature.
$EN_DIS
**/
UINT8 PchS0ixAutoDemotion;
/** Offset 0x1A6D - Latch Events C10 Exit
When this bit is set to 1, SLP_S0# entry events in SLP_S0_DEBUG_REGx registers are
captured on C10 exit (instead of C10 entry which is default)
$EN_DIS
**/
UINT8 PchPmLatchEventsC10Exit;
/** Offset 0x1A6E - PMC ADR enable
Enable/disable asynchronous DRAM refresh
$EN_DIS
**/
UINT8 PmcAdrEn;
/** Offset 0x1A6F - PMC ADR timer configuration enable
Enable/disable ADR timer configuration
$EN_DIS
**/
UINT8 PmcAdrTimerEn;
/** Offset 0x1A70 - PMC ADR phase 1 timer value
Enable/disable ADR timer configuration
**/
UINT8 PmcAdrTimer1Val;
/** Offset 0x1A71 - PMC ADR phase 1 timer multiplier value
Specify the multiplier value for phase 1 ADR timer
**/
UINT8 PmcAdrMultiplier1Val;
/** Offset 0x1A72 - PMC ADR host reset partition enable
Specify whether PMC should set ADR_RST_STS bit after receiving Reset_Warn_Ack DMI message
$EN_DIS
**/
UINT8 PmcAdrHostPartitionReset;
/** Offset 0x1A73 - PMC ADR source select override enable
Tells the FSP to update the source select with platform value
$EN_DIS
**/
UINT8 PmcAdrSrcOverride;
/** Offset 0x1A74 - PMC ADR source selection
Specify which sources should cause ADR flow
**/
UINT32 PmcAdrSrcSel;
/** Offset 0x1A78 - PMC WDT enable
Enable/disable PMC WDT configuration
$EN_DIS
**/
UINT8 PmcWdtTimerEn;
/** Offset 0x1A79 - PCIe RootPort Clock Gating
Describes whether the PCI Express Clock Gating for each root port is enabled by
platform modules. 0: Disable; 1: Enable(Default).
$EN_DIS
**/
UINT8 PcieClockGating[29];
/** Offset 0x1A96 - PCIe RootPort Power Gating
Describes whether the PCI Express Power Gating for each root port is enabled by
platform modules. 0: Disable; 1: Enable(Default).
$EN_DIS
**/
UINT8 PciePowerGating[29];
/** Offset 0x1AB3 - FOMS Control Policy
Choose the Foms Control Policy, Default = 0
0: Auto, 1: Gen3 Foms, 2: Gen4 Foms, 3: Gen3 and Gen4 Foms
**/
UINT8 PcieFomsCp[29];
/** Offset 0x1AD0 - PCIe GPIO Assertion in Link Down
Describes whether the PCIe GPIO Assertion in Link Down programming is enabled for
each root portby platform modules. 0: Disable; 1: Enable(Default).
$EN_DIS
**/
UINT8 LinkDownGpios[29];
/** Offset 0x1AED - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3
Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3, Each
value in array can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxRate3UniqTranEnable[10];
/** Offset 0x1AF7 - USB 3.0 TX Output Unique Transition Bit Scale for rate 3
USB 3.0 TX Output Unique Transition Bit Scale for rate 3, HSIO_TX_DWORD9[6:0], Default
= 4Ch. One byte for each port.
**/
UINT8 Usb3HsioTxRate3UniqTran[10];
/** Offset 0x1B01 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2
Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2, Each
value in array can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxRate2UniqTranEnable[10];
/** Offset 0x1B0B - USB 3.0 TX Output Unique Transition Bit Scale for rate 2
USB 3.0 TX Output Unique Transition Bit Scale for rate 2, HSIO_TX_DWORD9[14:8],
Default = 4Ch. One byte for each port.
**/
UINT8 Usb3HsioTxRate2UniqTran[10];
/** Offset 0x1B15 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1
Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1, Each
value in array can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxRate1UniqTranEnable[10];
/** Offset 0x1B1F - USB 3.0 TX Output Unique Transition Bit Scale for rate 1
USB 3.0 TX Output Unique Transition Bit Scale for rate 1, HSIO_TX_DWORD9[22:16],
Default = 4Ch. One byte for each port.
**/
UINT8 Usb3HsioTxRate1UniqTran[10];
/** Offset 0x1B29 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0
Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0, Each
value in array can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxRate0UniqTranEnable[10];
/** Offset 0x1B33 - USB 3.0 TX Output Unique Transition Bit Scale for rate 0
USB 3.0 TX Output Unique Transition Bit Scale for rate 0, HSIO_TX_DWORD9[30:24],
Default = 4Ch. One byte for each port.
**/
UINT8 Usb3HsioTxRate0UniqTran[10];
/** Offset 0x1B3D - Skip PAM regsiter lock
Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
PAM registers will be locked by RC
$EN_DIS
**/
UINT8 SkipPamLock;
/** Offset 0x1B3E - Enable/Disable IGFX RenderStandby
Enable(Default): Enable IGFX RenderStandby, Disable: Disable IGFX RenderStandby
$EN_DIS
**/
UINT8 RenderStandby;
/** Offset 0x1B3F - Enable/Disable GT Configuration
Enable(Default): Configure GT for use, Disable: Skip GT Configuration
$EN_DIS
**/
UINT8 ConfigureGT;
/** Offset 0x1B40 - GT Frequency Limit
0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
0x18: 1200 Mhz
0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
0x18: 1200 Mhz
**/
UINT8 GtFreqMax;
/** Offset 0x1B41 - Disable Turbo GT
0=Disable: GT frequency is not limited, 1=Enable: Disables Turbo GT frequency
$EN_DIS
**/
UINT8 DisableTurboGt;
/** Offset 0x1B42 - Enable RC1p GT frequency request to PMA (provided all other conditions are met)
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 RC1pGtFreqEnable;
/** Offset 0x1B43 - Enable RC1p Media frequency request to PMA (provided all other conditions are met)
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 RC1pMediaFreqEnable;
/** Offset 0x1B44 - Enable TSN Multi-VC
Enable/disable Multi Virtual Channels(VC) in TSN.
$EN_DIS
**/
UINT8 PchTsnMultiVcEnable;
/** Offset 0x1B45 - PMC Limit Powergating
Enable/disable Limit PSF powergating to C3 and deeper states
$EN_DIS
**/
UINT8 PmcLimitC3AndDeeperWA;
/** Offset 0x1B46
**/
UINT8 Rsvd380[10];
/** Offset 0x1B50 - LogoPixelHeight Address
Address of LogoPixelHeight
**/
UINT32 LogoPixelHeight;
/** Offset 0x1B54 - LogoPixelWidth Address
Address of LogoPixelWidth
**/
UINT32 LogoPixelWidth;
/** Offset 0x1B58 - Enable/Disable Media Configuration
Enable(Default): Configure Media for use, Disable: Skip Media Configuration
$EN_DIS
**/
UINT8 ConfigureMedia;
/** Offset 0x1B59 - ITbt Usb4CmMode value
ITbt Usb4CmMode value. 0:Firmware CM, 1:Software CM
**/
UINT8 Usb4CmMode;
/** Offset 0x1B5A
**/
UINT8 Rsvd390[2];
/** Offset 0x1B5C - HorizontalResolution for PEI Logo
HorizontalResolution from PEIm Gfx for PEI Logo
**/
UINT32 HorizontalResolution;
/** Offset 0x1B60 - VerticalResolution for PEI Logo
VerticalResolution from PEIm Gfx for PEI Logo
**/
UINT32 VerticalResolution;
/** Offset 0x1B64 - Enable/Disable IGFX Media Standby
Enable(Default): Enable IGFX Media Standby, Disable: Disable IGFX MediaStandby
$EN_DIS
**/
UINT8 MediaStandby;
/** Offset 0x1B65 - SaPostMemTestRsvd
Reserved for SA Post-Mem Test
$EN_DIS
**/
UINT8 SaPostMemTestRsvd[32];
/** Offset 0x1B85
**/
UINT8 SaFspsUpdRsvd[32];
/** Offset 0x1BA5 - RSR feature
Enable or Disable RSR feature; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 EnableRsr;
/** Offset 0x1BA6 - ReservedCpuPostMem1
Reserved for CPU Post-Mem 1
$EN_DIS
**/
UINT8 ReservedCpuPostMem1[4];
/** Offset 0x1BAA - Enable or Disable HWP
Enable/Disable Intel(R) Speed Shift Technology support. Enabling will expose the
CPPC v2 interface to allow for hardware controlled P-states. 0: Disable; 1:
Enable;
$EN_DIS
**/
UINT8 Hwp;
/** Offset 0x1BAB - Package Long duration turbo mode time
Power Limit 1 Time Window value in seconds. The value may vary from 0 to 128. 0
= default value (28 sec for Mobile and 8 sec for Desktop). Defines time window
which Processor Base Power (TDP) value should be maintained. Valid values(Unit
in seconds) 0 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 ,
80 , 96 , 112 , 128
**/
UINT8 PowerLimit1Time;
/** Offset 0x1BAC - Short Duration Turbo Mode
Enable/Disable Power Limit 2 override. If this option is disabled, BIOS will program
the default values for Power Limit 2. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 PowerLimit2;
/** Offset 0x1BAD - Turbo settings Lock
Enable/Disable locking of Package Power Limit settings. When enabled, PACKAGE_POWER_LIMIT
MSR will be locked and a reset will be required to unlock the register. 0: Disable;
1: Enable
$EN_DIS
**/
UINT8 TurboPowerLimitLock;
/** Offset 0x1BAE - Package PL3 time window
Power Limit 3 Time Window value in Milli seconds. Indicates the time window over
which Power Limit 3 value should be maintained. If the value is 0, BIOS leaves
the hardware default value. Valid value: 0, 3-8, 10, 12, 14, 16, 20, 24,
28, 32, 40, 48, 56, 64.
**/
UINT8 PowerLimit3Time;
/** Offset 0x1BAF - Package PL3 Duty Cycle
Specify the duty cycle in percentage that the CPU is required to maintain over the
configured time window. Range is 0-100.
**/
UINT8 PowerLimit3DutyCycle;
/** Offset 0x1BB0 - Package PL3 Lock
Power Limit 3 Lock. When enabled PL3 configurations are locked during OS. When disabled
PL3 configuration can be changed during OS. 0: Disable ; 1:Enable
$EN_DIS
**/
UINT8 PowerLimit3Lock;
/** Offset 0x1BB1 - Package PL4 Lock
Power Limit 4 Lock. When enabled PL4 configurations are locked during OS. When disabled
PL4 configuration can be changed during OS. 0: Disable ; 1:Enable
$EN_DIS
**/
UINT8 PowerLimit4Lock;
/** Offset 0x1BB2 - TCC Activation Offset
TCC Activation Offset. Offset from factory set TCC activation temperature at which
the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation
Temperature, in volts. Default = 0h.
**/
UINT8 TccActivationOffset;
/** Offset 0x1BB3 - Tcc Offset Clamp Enable/Disable
Tcc Offset Clamp for Runtime Average Temperature Limit (RATL) allows CPU to throttle
below P1. 0: Disabled; 1: Enabled.
$EN_DIS
**/
UINT8 TccOffsetClamp;
/** Offset 0x1BB4 - Tcc Offset Lock
Tcc Offset Lock for Runtime Average Temperature Limit (RATL) to lock temperature
target; 0: Disabled; 1: Enabled.
$EN_DIS
**/
UINT8 TccOffsetLock;
/** Offset 0x1BB5 - Custom Ratio State Entries
The number of custom ratio state entries, ranges from 0 to 40 for a valid custom
ratio table. Sets the number of custom P-states. At least 2 states must be present
**/
UINT8 NumberOfEntries;
/** Offset 0x1BB6 - Custom Short term Power Limit time window
Power Limit 1 Time Window value in seconds. The value may vary from 0 to 128. 0
= default value (28 sec for Mobile and 8 sec for Desktop). Defines time window
which Processor Base Power (TDP) value should be maintained.
**/
UINT8 Custom1PowerLimit1Time;
/** Offset 0x1BB7 - Custom Turbo Activation Ratio
Custom value for Turbo Activation Ratio. Needs to be configured with valid values
from LFM to Max Turbo. 0 means don't use custom value. Valid Range 0 to 255
**/
UINT8 Custom1TurboActivationRatio;
/** Offset 0x1BB8 - Custom Config Tdp Control
Config Tdp(Base Power) Control (0/1/2) value for custom cTDP(Assured Power) level
1. Valid Range is 0 to 2
**/
UINT8 Custom1ConfigTdpControl;
/** Offset 0x1BB9 - Custom Short term Power Limit time window
Power Limit 1 Time Window value in seconds. The value may vary from 0 to 128. 0
= default value (28 sec for Mobile and 8 sec for Desktop). Defines time window
which Processor Base Power (TDP) value should be maintained.
**/
UINT8 Custom2PowerLimit1Time;
/** Offset 0x1BBA - Custom Turbo Activation Ratio
Custom value for Turbo Activation Ratio. Needs to be configured with valid values
from LFM to Max Turbo. 0 means don't use custom value. Valid Range 0 to 255
**/
UINT8 Custom2TurboActivationRatio;
/** Offset 0x1BBB - Custom Config Tdp Control
Config Tdp(Base Power) Control (0/1/2) value for custom cTDP(Assured Power) level
1. Valid Range is 0 to 2
**/
UINT8 Custom2ConfigTdpControl;
/** Offset 0x1BBC - Custom Short term Power Limit time window
Power Limit 1 Time Window value in seconds. The value may vary from 0 to 128. 0
= default value (28 sec for Mobile and 8 sec for Desktop). Defines time window
which Processor Base Power (TDP) value should be maintained.
**/
UINT8 Custom3PowerLimit1Time;
/** Offset 0x1BBD - Custom Turbo Activation Ratio
Custom value for Turbo Activation Ratio. Needs to be configured with valid values
from LFM to Max Turbo. 0 means don't use custom value. Valid Range 0 to 255
**/
UINT8 Custom3TurboActivationRatio;
/** Offset 0x1BBE - Custom Config Tdp Control
Config Tdp(Base Power) Control (0/1/2) value for custom cTDP(Assured Power) level
1. Valid Range is 0 to 2
**/
UINT8 Custom3ConfigTdpControl;
/** Offset 0x1BBF - ConfigTdp mode settings Lock
cTDP(Assured Power) Mode Lock sets the Lock bits on TURBO_ACTIVATION_RATIO and CONFIG_TDP_CONTROL.
Note: When CTDP(Assured Power) Lock is enabled Custom ConfigTDP Count will be forced
to 1 and Custom ConfigTDP Boot Index will be forced to 0. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 ConfigTdpLock;
/** Offset 0x1BC0 - Load Configurable TDP SSDT
Enables cTDP(Assured Power) control via runtime ACPI BIOS methods. This 'BIOS only'
feature does not require EC or driver support. 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 ConfigTdpBios;
/** Offset 0x1BC1 - PL1 Enable value
Enable/Disable Platform Power Limit 1 programming. If this option is enabled, it
activates the PL1 value to be used by the processor to limit the average power
of given time window. 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PsysPowerLimit1;
/** Offset 0x1BC2 - PL1 timewindow
Platform Power Limit 1 Time Window value in seconds. The value may vary from 0 to
128. 0 = default values. Indicates the time window over which Platform Processor
Base Power (TDP) value should be maintained. Valid values(Unit in seconds) 0 to
8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
UINT8 PsysPowerLimit1Time;
/** Offset 0x1BC3 - PL2 Enable Value
Enable/Disable Platform Power Limit 2 programming. If this option is disabled, BIOS
will program the default values for Platform Power Limit 2. 0: Disable;
1: Enable.
$EN_DIS
**/
UINT8 PsysPowerLimit2;
/** Offset 0x1BC4 - Enable or Disable MLC Streamer Prefetcher
Enable or Disable MLC Streamer Prefetcher; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MlcStreamerPrefetcher;
/** Offset 0x1BC5 - Enable or Disable MLC Spatial Prefetcher
Enable or Disable MLC Spatial Prefetcher; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 MlcSpatialPrefetcher;
/** Offset 0x1BC6 - Enable or Disable Monitor /MWAIT instructions
Enable/Disable MonitorMWait, if Disable MonitorMwait, the AP threads Idle Manner
should not set in MWAIT Loop. 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MonitorMwaitEnable;
/** Offset 0x1BC7 - Enable or Disable initialization of machine check registers
Enable or Disable initialization of machine check registers; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MachineCheckEnable;
/** Offset 0x1BC8 - AP Idle Manner of waiting for SIPI
AP threads Idle Manner for waiting signal to run. 1: HALT loop; 2: MWAIT loop;
3: RUN loop.
1: HALT loop, 2: MWAIT loop, 3: RUN loop
**/
UINT8 ApIdleManner;
/** Offset 0x1BC9 - Control on Processor Trace output scheme
Control on Processor Trace output scheme; 0: Single Range Output; 1: ToPA Output.
0: Single Range Output, 1: ToPA Output
**/
UINT8 ProcessorTraceOutputScheme;
/** Offset 0x1BCA - Enable or Disable Processor Trace feature
Enable or Disable Processor Trace feature; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 ProcessorTraceEnable;
/** Offset 0x1BCB - Enable or Disable Intel SpeedStep Technology
Allows more than two frequency ranges to be supported. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 Eist;
/** Offset 0x1BCC - Enable or Disable Energy Efficient P-state
Enable/Disable Energy Efficient P-state feature. When set to 0, will disable access
to ENERGY_PERFORMANCE_BIAS MSR and CPUID Function will read 0 indicating no support
for Energy Efficient policy setting. When set to 1 will enable access to ENERGY_PERFORMANCE_BIAS
MSR and CPUID Function will read 1 indicating Energy Efficient policy setting is
supported. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 EnergyEfficientPState;
/** Offset 0x1BCD - Enable or Disable Energy Efficient Turbo
Enable/Disable Energy Efficient Turbo Feature. This feature will opportunistically
lower the turbo frequency to increase efficiency. Recommended only to disable in
overclocking situations where turbo frequency must remain constant. Otherwise,
leave enabled. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 EnergyEfficientTurbo;
/** Offset 0x1BCE - Enable or Disable T states
Enable or Disable T states; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 TStates;
/** Offset 0x1BCF - Enable or Disable Bi-Directional PROCHOT#
Enable or Disable Bi-Directional PROCHOT#; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 BiProcHot;
/** Offset 0x1BD0 - Enable or Disable PROCHOT# signal being driven externally
Enable or Disable PROCHOT# signal being driven externally; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DisableProcHotOut;
/** Offset 0x1BD1 - Enable or Disable PROCHOT# Response
Enable or Disable PROCHOT# Response; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 ProcHotResponse;
/** Offset 0x1BD2 - Enable or Disable VR Thermal Alert
Enable or Disable VR Thermal Alert; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 DisableVrThermalAlert;
/** Offset 0x1BD3 - Enable or Disable Thermal Reporting
Enable or Disable Thermal Reporting through ACPI tables; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 EnableAllThermalFunctions;
/** Offset 0x1BD4 - Enable or Disable Thermal Monitor
Enable or Disable Thermal Monitor; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 ThermalMonitor;
/** Offset 0x1BD5 - Enable or Disable CPU power states (C-states)
Enable/Disable CPU Power Management. Allows CPU to go to C states when it's not
100% utilized. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 Cx;
/** Offset 0x1BD6 - Configure C-State Configuration Lock
Configure MSR to CFG Lock bit. 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PmgCstCfgCtrlLock;
/** Offset 0x1BD7 - Enable or Disable Enhanced C-states
Enable/Disable C1E. When enabled, CPU will switch to minimum speed when all cores
enter C-State. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 C1e;
/** Offset 0x1BD8 - Enable or Disable Package Cstate Demotion
Enable or Disable Package C-State Demotion. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 PkgCStateDemotion;
/** Offset 0x1BD9 - Enable or Disable Package Cstate UnDemotion
Enable or Disable Package C-State Un-Demotion. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 PkgCStateUnDemotion;
/** Offset 0x1BDA - Enable or Disable CState-Pre wake
Disable - to disable the Cstate Pre-Wake. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 CStatePreWake;
/** Offset 0x1BDB - Enable or Disable TimedMwait Support.
Enable or Disable TimedMwait Support. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 TimedMwait;
/** Offset 0x1BDC - Enable or Disable IO to MWAIT redirection
When set, will map IO_read instructions sent to IO registers PMG_IO_BASE_ADDRBASE+offset
to MWAIT(offset). 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 CstCfgCtrIoMwaitRedirection;
/** Offset 0x1BDD - Set the Max Pkg Cstate
Maximum Package C State Limit Setting. Cpu Default: Leaves to Factory default value.
Auto: Initializes to deepest available Package C State Limit. Valid values 0 -
C0/C1, 1 - C2, 2 - C3, 3 - C6, 4 - C7, 5 - C7S, 6 - C8, 7 - C9, 8 - C10, 254 -
CPU Default, 255 - Auto
**/
UINT8 PkgCStateLimit;
/** Offset 0x1BDE - Interrupt Redirection Mode Select
Interrupt Redirection Mode Select for Logical Interrupts. 0: Fixed priority; 1:
Round robin; 2: Hash vector; 7: No change.
**/
UINT8 PpmIrmSetting;
/** Offset 0x1BDF - Lock prochot configuration
Lock prochot configuration Enable/Disable; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 ProcHotLock;
/** Offset 0x1BE0 - Configuration for boot TDP selection
cTDP(Assured Power) Mode as Nominal/Level1/Level2/Deactivate TDP(Base Power) selection.
Deactivate option will set MSR to Nominal and MMIO to Zero. 0: TDP(Base Power)
Nominal; 1: TDP(Base Power) Down; 2: TDP(Base Power) Up;0xFF : Deactivate
**/
UINT8 ConfigTdpLevel;
/** Offset 0x1BE1 - Max P-State Ratio
Maximum P-state ratio to use in the custom P-state table. Valid Range 0 to 0x7F
**/
UINT8 MaxRatio;
/** Offset 0x1BE2 - P-state ratios for custom P-state table
P-state ratios for custom P-state table. NumberOfEntries has valid range between
0 to 40. For no. of P-States supported(NumberOfEntries) , StateRatio[NumberOfEntries]
are configurable. Valid Range of each entry is 0 to 0x7F
**/
UINT8 StateRatio[40];
/** Offset 0x1C0A - P-state ratios for max 16 version of custom P-state table
P-state ratios for max 16 version of custom P-state table. This table is used for
OS versions limited to a max of 16 P-States. If the first entry of this table is
0, or if Number of Entries is 16 or less, then this table will be ignored, and
up to the top 16 values of the StateRatio table will be used instead. Valid Range
of each entry is 0 to 0x7F
**/
UINT8 StateRatioMax16[16];
/** Offset 0x1C1A
**/
UINT8 Rsvd400[2];
/** Offset 0x1C1C - Package Long duration turbo mode power limit
Power Limit 1 in Milli Watts. BIOS will round to the nearest 1/8W when programming.
Value set 120 = 15W. 0 = no custom override. Overclocking SKU: Value must be between
Max and Min Power Limits. Other SKUs: This value must be between Min Power Limit
and Processor Base Power (TDP) Limit. If value is 0, BIOS will program Processor
Base Power (TDP) value. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. Valid
Range 0 to 32767.
**/
UINT32 PowerLimit1;
/** Offset 0x1C20 - Package Short duration turbo mode power limit
Power Limit 2 in Milli Watts. BIOS will round to the nearest 1/8W when programming.
Value set 120 = 15W. If the value is 0, BIOS will program this value as 1.25*Processor
Base Power (TDP). Processor applies control policies such that the package power
does not exceed this limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 32767.
**/
UINT32 PowerLimit2Power;
/** Offset 0x1C24 - Package PL3 power limit
Power Limit 3 in Milli Watts. BIOS will round to the nearest 1/8W when programming.
Value set 120 = 15W. XE SKU: Any value can be programmed. Overclocking SKU: Value
must be between Max and Min Power Limits. Other SKUs: This value must be between
Min Power Limit and Processor Base Power (TDP) Limit. If the value is 0, BIOS leaves
the hardware default value. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 32767.
**/
UINT32 PowerLimit3;
/** Offset 0x1C28 - Package PL4 power limit
Power Limit 4 in Milli Watts. BIOS will round to the nearest 1/8W when programming.
Value set 120 = 15W. If the value is 0, BIOS leaves default value. Units are based
on POWER_MGMT_CONFIG.CustomPowerUnit. Valid Range 0 to 32767.
**/
UINT32 PowerLimit4;
/** Offset 0x1C2C - Package PL4 boost configuration
Configure Power Limit 4 Boost in Watts. Valid Range 0 to 1023 in step size of 1
Watt. The value 0 means disable.
**/
UINT16 PowerLimit4Boost;
/** Offset 0x1C2E
**/
UINT8 Rsvd410[2];
/** Offset 0x1C30 - Tcc Offset Time Window for RATL
**/
UINT32 TccOffsetTimeWindowForRatl;
/** Offset 0x1C34 - Short term Power Limit value for custom cTDP level 1
Power Limit 1 in Milli Watts. BIOS will round to the nearest 1/8W when programming.
Value set 120 = 15W. 0 = no custom override. Overclocking SKU: Value must be between
Max and Min Power Limits. Other SKUs: This value must be between Min Power Limit
and Processor Base Power (TDP) Limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 32767.
**/
UINT32 Custom1PowerLimit1;
/** Offset 0x1C38 - Long term Power Limit value for custom cTDP level 1
Power Limit 2 value in Milli Watts. BIOS will round to the nearest 1/8W when programming.
Value set 120 = 15W. 0 = no custom override. Processor applies control policies
such that the package power does not exceed this limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 32767.
**/
UINT32 Custom1PowerLimit2;
/** Offset 0x1C3C - Short term Power Limit value for custom cTDP level 2
Power Limit 1 in Milli Watts. BIOS will round to the nearest 1/8W when programming.
Value set 120 = 15W. 0 = no custom override. Overclocking SKU: Value must be between
Max and Min Power Limits. Other SKUs: This value must be between Min Power Limit
and Processor Base Power (TDP) Limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 32767.
**/
UINT32 Custom2PowerLimit1;
/** Offset 0x1C40 - Long term Power Limit value for custom cTDP level 2
Power Limit 2 value in Milli Watts. BIOS will round to the nearest 1/8W when programming.
Value set 120 = 15W. 0 = no custom override. Processor applies control policies
such that the package power does not exceed this limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 32767.
**/
UINT32 Custom2PowerLimit2;
/** Offset 0x1C44 - Short term Power Limit value for custom cTDP level 3
Power Limit 1 in Milli Watts. BIOS will round to the nearest 1/8W when programming.
Value set 120 = 15W. 0 = no custom override. Overclocking SKU: Value must be between
Max and Min Power Limits. Other SKUs: This value must be between Min Power Limit
and Processor Base Power (TDP) Limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 32767.
**/
UINT32 Custom3PowerLimit1;
/** Offset 0x1C48 - Long term Power Limit value for custom cTDP level 3
Power Limit 2 value in Milli Watts. BIOS will round to the nearest 1/8W when programming.
Value set 120 = 15W. 0 = no custom override. Processor applies control policies
such that the package power does not exceed this limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 32767.
**/
UINT32 Custom3PowerLimit2;
/** Offset 0x1C4C - Platform PL1 power
Platform Power Limit 1 Power in Milli Watts. BIOS will round to the nearest 1/8W
when programming. Value set 120 = 15W. Any value can be programmed between Max
and Min Power Limits. This setting will act as the new PL1 value for the Package
RAPL algorithm. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. Valid Range
0 to 32767.
**/
UINT32 PsysPowerLimit1Power;
/** Offset 0x1C50 - Platform PL2 power
Platform Power Limit 2 Power in Milli Watts. BIOS will round to the nearest 1/8W
when programming. Value set 120 = 15W. Any value can be programmed between Max
and Min Power Limits. This setting will act as the new Max Turbo Power (PL2) value
for the Package RAPL algorithm. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 32767.
**/
UINT32 PsysPowerLimit2Power;
/** Offset 0x1C54 - CCF AutoGV
Enable/Disable CCF AutoGV; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 CcfAutoGv;
/** Offset 0x1C55 - Race To Halt
Enable/Disable Race To Halt feature. RTH will dynamically increase CPU frequency
in order to enter pkg C-State faster to reduce overall power. 0: Disable; 1:
Enable
$EN_DIS
**/
UINT8 RaceToHalt;
/** Offset 0x1C56 - Enable or Disable Three Strike Counter
Enable (default): Three Strike counter will be incremented. Disable: Prevents Three
Strike counter from incrementing; 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 ThreeStrikeCounter;
/** Offset 0x1C57 - Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT
Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT; 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 HwpInterruptControl;
/** Offset 0x1C58 - ReservedCpuPostMem2
Reserved for CPU Post-Mem 2
$EN_DIS
**/
UINT8 ReservedCpuPostMem2[4];
/** Offset 0x1C5C - Enable or Disable C1 Cstate Demotion
Enable or Disable C1 Cstate Auto Demotion. Disable; 1: Enable
$EN_DIS
**/
UINT8 C1StateAutoDemotion;
/** Offset 0x1C5D - Enable or Disable C1 Cstate UnDemotion
Enable or Disable C1 Cstate Un-Demotion. Disable; 1: Enable
$EN_DIS
**/
UINT8 C1StateUnDemotion;
/** Offset 0x1C5E - Minimum Ring ratio limit override
Minimum Ring ratio limit override. 0: Hardware defaults. Range: 0 - Max turbo
ratio limit
**/
UINT8 MinRingRatioLimit;
/** Offset 0x1C5F - Maximum Ring ratio limit override
Maximum Ring ratio limit override. 0: Hardware defaults. Range: 0 - Max turbo
ratio limit
**/
UINT8 MaxRingRatioLimit;
/** Offset 0x1C60 - Enable or Disable Per Core P State OS control
Enable/Disable Per Core P state OS control mode. When set, the highest core request
is used for all other core requests. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 EnablePerCorePState;
/** Offset 0x1C61 - Enable or Disable HwP Autonomous Per Core P State OS control
Disable Autonomous PCPS Autonomous will request the same value for all cores all
the time. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 EnableHwpAutoPerCorePstate;
/** Offset 0x1C62 - Enable or Disable HwP Autonomous EPP Grouping
Enable EPP grouping Autonomous will request the same values for all cores with same
EPP. Disable EPP grouping autonomous will not necessarily request same values for
all cores with same EPP. 0: Disable ; 1: Enable
$EN_DIS
**/
UINT8 EnableHwpAutoEppGrouping;
/** Offset 0x1C63 - Enable Configurable TDP
Applies cTDP(Assured Power) initialization settings based on non-cTDP(Assured Power)
or cTDP(Assured Power). Default is 1: Applies to cTDP(Assured Power); if 0 then
applies non-cTDP(Assured Power) and BIOS will bypass cTDP(Assured Power) initialzation flow
$EN_DIS
**/
UINT8 ApplyConfigTdp;
/** Offset 0x1C64 - Misc Power Management MSR Lock
Enable/Disable HWP Lock support in Misc Power Management MSR. 0: Disable, 1:
Enable
$EN_DIS
**/
UINT8 HwpLock;
/** Offset 0x1C65 - Dual Tau Boost
Enable Dual Tau Boost feature. This is only applicable for Desktop 35W/65W/125W
sku. When DPTF is enabled this feature is ignored. 0: Disable; 1: Enable
$EN_DIS
**/
UINT8 DualTauBoost;
/** Offset 0x1C66 - Response Mode
Use Response Mode to adjust Psys_PL3 power reduction behavior. Battery-enabled systems
use Gradual Power Reduction. 0: Gradual Power Reduction ; 1: Aggressive
Power Reduction
0: Gradual Power Reduction, 1: Aggressive Power Reduction
**/
UINT8 StepDownMode;
/** Offset 0x1C67 - Power Floor Managment for SOC
Option to disable Power Floor Managment for SOC. Disabling this might effectively
raise power floor of the SoC and may lead to stability issues. 0: Disable, 1:
Enable
$EN_DIS
**/
UINT8 PowerFloorManagement;
/** Offset 0x1C68 - Power Floor Disaplay Disconnect
SoC can disconnect secondary/external display to lower SoC floor power (Default
enabled). 0: Disable: Display disconnect will not be used by SoC., 1: Enable
$EN_DIS
**/
UINT8 PowerFloorDisplayDisconnect;
/** Offset 0x1C69 - Resource Priority Feature
Enable/Disable Resource Priority Feature. Enable/Disable; 0: Disable ; 1:Enable
$EN_DIS
**/
UINT8 EnableRp;
/** Offset 0x1C6A - Power Floor PCIe Gen Downgrade
SoC can downgrade PCIe gen speed to lower SoC floor power (Default enabled). 0:
Disable: Reduction in PCIe gen speed will not be used by SoC., 1: Enable
$EN_DIS
**/
UINT8 PowerFloorPcieGenDowngrade;
/** Offset 0x1C6B - ReservedCpuPostMemTest
Reserved for CPU Post-Mem Test
$EN_DIS
**/
UINT8 ReservedCpuPostMemTest[13];
/** Offset 0x1C78
**/
UINT8 SecurityPostMemRsvd[16];
/** Offset 0x1C88 - End of Post message
Test, Send End of Post message. Disable(0x0): Disable EOP message, Send in PEI(0x1):
EOP send in PEI, Send in DXE(0x2)(Default): EOP send in DXE
0:Disable, 1:Send in PEI, 2:Send in DXE, 3:Reserved
**/
UINT8 EndOfPostMessage;
/** Offset 0x1C89 - D0I3 Setting for HECI Disable
Test, 0: disable, 1: enable, Setting this option disables setting D0I3 bit for all
HECI devices
$EN_DIS
**/
UINT8 DisableD0I3SettingForHeci;
/** Offset 0x1C8A - Mctp Broadcast Cycle
Test, Determine if MCTP Broadcast is enabled 0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 MctpBroadcastCycle;
/** Offset 0x1C8B - ME Unconfig on RTC clear
0: Disable ME Unconfig On Rtc Clear. 1: Enable ME Unconfig On Rtc Clear.
2: Cmos is clear, status unkonwn. 3: Reserved
0: Disable ME Unconfig On Rtc Clear, 1: Enable ME Unconfig On Rtc Clear, 2: Cmos
is clear, 3: Reserved
**/
UINT8 MeUnconfigOnRtcClear;
/** Offset 0x1C8C - Enforce Enhanced Debug Mode
Determine if ME should enter Enhanced Debug Mode. 0: disable, 1: enable
$EN_DIS
**/
UINT8 EnforceEDebugMode;
/** Offset 0x1C8D - CSE Data Resilience Support
0: Disable CSE Data Resilience Support. 1: Enable CSE Data Resilience Support.
$EN_DIS
**/
UINT8 CseDataResilience;
/** Offset 0x1C8E - MePostMemRsvd
Reserved for ME Post-Mem
$EN_DIS
**/
UINT8 MePostMemRsvd[16];
/** Offset 0x1C9E - Enable LOCKDOWN SMI
Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit.
$EN_DIS
**/
UINT8 PchLockDownGlobalSmi;
/** Offset 0x1C9F - Enable LOCKDOWN BIOS Interface
Enable BIOS Interface Lock Down bit to prevent writes to the Backup Control Register.
$EN_DIS
**/
UINT8 PchLockDownBiosInterface;
/** Offset 0x1CA0 - Unlock all GPIO pads
Force all GPIO pads to be unlocked for debug purpose.
$EN_DIS
**/
UINT8 PchUnlockGpioPads;
/** Offset 0x1CA1 - PCH Unlock SideBand access
The SideBand PortID mask for certain end point (e.g. PSFx) will be locked before
3rd party code execution. 0: Lock SideBand access; 1: Unlock SideBand access.
$EN_DIS
**/
UINT8 PchSbAccessUnlock;
/** Offset 0x1CA2
**/
UINT8 Rsvd420[2];
/** Offset 0x1CA4 - PCIE RP Ltr Max Snoop Latency
Latency Tolerance Reporting, Max Snoop Latency.
**/
UINT16 PcieRpLtrMaxSnoopLatency[29];
/** Offset 0x1CDE - PCIE RP Ltr Max No Snoop Latency
Latency Tolerance Reporting, Max Non-Snoop Latency.
**/
UINT16 PcieRpLtrMaxNoSnoopLatency[29];
/** Offset 0x1D18 - PCIE RP Snoop Latency Override Mode
Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
UINT8 PcieRpSnoopLatencyOverrideMode[29];
/** Offset 0x1D35 - PCIE RP Snoop Latency Override Multiplier
Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
UINT8 PcieRpSnoopLatencyOverrideMultiplier[29];
/** Offset 0x1D52 - PCIE RP Snoop Latency Override Value
Latency Tolerance Reporting, Snoop Latency Override Value.
**/
UINT16 PcieRpSnoopLatencyOverrideValue[29];
/** Offset 0x1D8C - PCIE RP Non Snoop Latency Override Mode
Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
UINT8 PcieRpNonSnoopLatencyOverrideMode[29];
/** Offset 0x1DA9 - PCIE RP Non Snoop Latency Override Multiplier
Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
UINT8 PcieRpNonSnoopLatencyOverrideMultiplier[29];
/** Offset 0x1DC6 - PCIE RP Non Snoop Latency Override Value
Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
UINT16 PcieRpNonSnoopLatencyOverrideValue[29];
/** Offset 0x1E00 - PCIE RP Slot Power Limit Scale
Specifies scale used for slot power limit value. Leave as 0 to set to default.
**/
UINT8 PcieRpSlotPowerLimitScale[29];
/** Offset 0x1E1D
**/
UINT8 Rsvd430[1];
/** Offset 0x1E1E - PCIE RP Slot Power Limit Value
Specifies upper limit on power supplie by slot. Leave as 0 to set to default.
**/
UINT16 PcieRpSlotPowerLimitValue[29];
/** Offset 0x1E58 - PCIE RP Enable Port8xh Decode
This member describes whether PCIE root port Port 8xh Decode is enabled. 0: Disable;
1: Enable.
$EN_DIS
**/
UINT8 PcieEnablePort8xhDecode;
/** Offset 0x1E59 - PCIE Port8xh Decode Port Index
The Index of PCIe Port that is selected for Port8xh Decode (0 Based).
**/
UINT8 PchPciePort8xhDecodePortIndex;
/** Offset 0x1E5A - PCH Energy Reporting
Disable/Enable PCH to CPU energy report feature.
$EN_DIS
**/
UINT8 PchPmDisableEnergyReport;
/** Offset 0x1E5B - PCH Sata Test Mode
Allow entrance to the PCH SATA test modes.
$EN_DIS
**/
UINT8 SataTestMode;
/** Offset 0x1E5C - PCH USB OverCurrent mapping lock enable
If this policy option is enabled then BIOS will program OCCFDONE bit in xHCI meaning
that OC mapping data will be consumed by xHCI and OC mapping registers will be locked.
$EN_DIS
**/
UINT8 PchXhciOcLock;
/** Offset 0x1E5D - Low Power Mode Enable/Disable config mask
Configure if respective S0i2/3 sub-states are to be supported. Each bit corresponds
to one sub-state (LPMx - BITx): LPM0-s0i2.0, LPM1-s0i2.1, LPM2-s0i2.2, LPM3-s0i3.0,
LPM4-s0i3.1, LPM5-s0i3.2, LPM6-s0i3.3, LPM7-s0i3.4.
**/
UINT8 PmcLpmS0ixSubStateEnableMask;
/** Offset 0x1E5E - Low Power Mode Enable/Disable config mask
Configure if respective S0i2/3 sub-states are to be supported. Each bit corresponds
to one sub-state (LPMx - BITx): LPM0-s0i2.0, LPM1-s0i2.1, LPM2-s0i2.2, LPM3-s0i3.0,
LPM4-s0i3.1, LPM5-s0i3.2, LPM6-s0i3.3, LPM7-s0i3.4.
**/
UINT8 PmcPchLpmS0ixSubStateEnableMask;
/** Offset 0x1E5F - PCH PMC ER Debug mode
Disable/Enable Energy Reporting Debug Mode.
$EN_DIS
**/
UINT8 PchPmErDebugMode;
/** Offset 0x1E60 - CPPM Forced Alignment Enable
Enable/Disable CPPM Force Alignment. When enabled, PMC allows stalling of the backbone
or blocking the DMI transmit arbiter
$EN_DIS
**/
UINT8 CppmFaEn;
/** Offset 0x1E61 - PCH Lan WOL Fast Support
Enables bit B_PCH_ACPI_GPE0_EN_127_96_PME_B0 during PchLanSxCallback in PchLanSxSmm.
$EN_DIS
**/
UINT8 PchLanWOLFastSupport;
/** Offset 0x1E62 - Platform ATX Telemetry Unit
Set ATX Telemetry Unit in Watts or Percentage; 0: Watts; 1: Percent
$EN_DIS
**/
UINT8 PlatformAtxTelemetryUnit;
/** Offset 0x1E63 - PCIE RP LTR Override Spec Complaint
Override LTR based on Ep capability.
**/
UINT8 PcieRpLtrOverrideSpecComplaint[29];
/** Offset 0x1E80
**/
UINT8 PchMeFspsUpdRsvd[71];
/** Offset 0x1EC7 - PMC C10 dynamic threshold dajustment enable
Set if you want to enable PMC C10 dynamic threshold adjustment. Only works on supported SKUs
$EN_DIS
**/
UINT8 PmcC10DynamicThresholdAdjustment;
/** Offset 0x1EC8 - Turbo Ratio Limit Ratio array
Performance-core Turbo Ratio Limit Ratio0-7 (TRLR) defines the turbo ratio (max
is 85 in normal mode and 120 in core extension mode). Ratio[0]: This Turbo Ratio
Limit Ratio0 must be greater than or equal all other ratio values. If this value
is invalid, thn set all other active cores to minimum. Otherwise, align the Ratio
Limit to 0. Please check each active cores. Ratio[1~7]: This Turbo Ratio Limit
Ratio1 must be <= to Turbo Ratio Limit Ratio0~6.
**/
UINT8 TurboRatioLimitRatio[8];
/** Offset 0x1ED0 - Turbo Ratio Limit Num Core array
Performance-core Turbo Ratio Limit Core0~7 defines the core range, the turbo ratio
is defined in Turbo Ratio Limit Ratio0~7. If value is zero, this entry is ignored.
**/
UINT8 TurboRatioLimitNumCore[8];
/** Offset 0x1ED8 - ATOM Turbo Ratio Limit Ratio array
Efficient-core Turbo Ratio Limit Ratio0-7 defines the turbo ratio (max is 85 irrespective
of the core extension mode), the core range is defined in E-core Turbo Ratio Limit
CoreCount0-7.
**/
UINT8 AtomTurboRatioLimitRatio[8];
/** Offset 0x1EE0 - ATOM Turbo Ratio Limit Num Core array
Efficient-core Turbo Ratio Limit CoreCount0-7 defines the core range, the turbo
ratio is defined in E-core Turbo Ratio Limit Ratio0-7. If value is zero, this entry
is ignored.
**/
UINT8 AtomTurboRatioLimitNumCore[8];
/** Offset 0x1EE8
**/
UINT8 Rsvd440[4];
/** Offset 0x1EEC - FspEventHandler
Optional pointer to the boot loader's implementation of FSP_EVENT_HANDLER.
**/
UINT32 FspEventHandler;
/** Offset 0x1EF0 - Type C Port x Convert to TypeA
Enable / Disable(default) Type C Port x Convert to TypeA
$EN_DIS
**/
UINT8 EnableTcssCovTypeA[4];
/** Offset 0x1EF4
**/
UINT8 Rsvd450[16];
/** Offset 0x1F04
**/
UINT8 ReservedFspsUpd[12];
} FSP_S_CONFIG;
/** Fsp S UPD Configuration
**/
typedef struct {
/** Offset 0x0000
**/
FSP_UPD_HEADER FspUpdHeader;
/** Offset 0x0020
**/
FSPS_ARCH_UPD FspsArchUpd;
/** Offset 0x0040
**/
FSP_S_CONFIG FspsConfig;
/** Offset 0x1F10
**/
UINT8 Rsvd600[6];
/** Offset 0x1F16
**/
UINT16 UpdTerminator;
} FSPS_UPD;
#pragma pack()
#endif