329 lines
12 KiB
C
329 lines
12 KiB
C
/** @file
|
|
Header file for GpioConfig structure used by GPIO library.
|
|
|
|
@copyright
|
|
Copyright (c) 2014 - 2019, Intel Corporation. All rights reserved.<BR>
|
|
|
|
SPDX-License-Identifier: BSD-2-Clause-Patent
|
|
|
|
@par Specification Reference:
|
|
**/
|
|
#ifndef _GPIO_CONFIG_H_
|
|
#define _GPIO_CONFIG_H_
|
|
|
|
#pragma pack(push, 1)
|
|
|
|
///
|
|
/// For any GpioPad usage in code use GPIO_PAD type
|
|
///
|
|
typedef UINT32 GPIO_PAD;
|
|
|
|
|
|
///
|
|
/// For any GpioGroup usage in code use GPIO_GROUP type
|
|
///
|
|
typedef UINT32 GPIO_GROUP;
|
|
|
|
/**
|
|
GPIO configuration structure used for pin programming.
|
|
Structure contains fields that can be used to configure pad.
|
|
**/
|
|
typedef struct {
|
|
/**
|
|
Pad Mode
|
|
Pad can be set as GPIO or one of its native functions.
|
|
When in native mode setting Direction (except Inversion), OutputState,
|
|
InterruptConfig, Host Software Pad Ownership and OutputStateLock are unnecessary.
|
|
Refer to definition of GPIO_PAD_MODE.
|
|
Refer to EDS for each native mode according to the pad.
|
|
**/
|
|
UINT32 PadMode : 5;
|
|
/**
|
|
Host Software Pad Ownership
|
|
Set pad to ACPI mode or GPIO Driver Mode.
|
|
Refer to definition of GPIO_HOSTSW_OWN.
|
|
**/
|
|
UINT32 HostSoftPadOwn : 2;
|
|
/**
|
|
GPIO Direction
|
|
Can choose between In, In with inversion, Out, both In and Out, both In with inversion and out or disabling both.
|
|
Refer to definition of GPIO_DIRECTION for supported settings.
|
|
**/
|
|
UINT32 Direction : 6;
|
|
/**
|
|
Output State
|
|
Set Pad output value.
|
|
Refer to definition of GPIO_OUTPUT_STATE for supported settings.
|
|
This setting takes place when output is enabled.
|
|
**/
|
|
UINT32 OutputState : 2;
|
|
/**
|
|
GPIO Interrupt Configuration
|
|
Set Pad to cause one of interrupts (IOxAPIC/SCI/SMI/NMI).
|
|
This setting is applicable only if GPIO is in GpioMode with input enabled.
|
|
Refer to definition of GPIO_INT_CONFIG for supported settings.
|
|
**/
|
|
UINT32 InterruptConfig : 9;
|
|
/**
|
|
GPIO Power Configuration.
|
|
This setting controls Pad Reset Configuration.
|
|
Refer to definition of GPIO_RESET_CONFIG for supported settings.
|
|
**/
|
|
UINT32 PowerConfig : 8;
|
|
/**
|
|
GPIO Electrical Configuration
|
|
This setting controls pads termination.
|
|
Refer to definition of GPIO_ELECTRICAL_CONFIG for supported settings.
|
|
**/
|
|
UINT32 ElectricalConfig : 9;
|
|
/**
|
|
GPIO Lock Configuration
|
|
This setting controls pads lock.
|
|
Refer to definition of GPIO_LOCK_CONFIG for supported settings.
|
|
**/
|
|
UINT32 LockConfig : 4;
|
|
/**
|
|
Additional GPIO configuration
|
|
Refer to definition of GPIO_OTHER_CONFIG for supported settings.
|
|
**/
|
|
UINT32 OtherSettings : 9;
|
|
UINT32 RsvdBits : 10; ///< Reserved bits for future extension
|
|
} GPIO_CONFIG;
|
|
|
|
|
|
typedef enum {
|
|
GpioHardwareDefault = 0x0 ///< Leave setting unmodified
|
|
} GPIO_HARDWARE_DEFAULT;
|
|
|
|
/**
|
|
GPIO Pad Mode
|
|
Refer to GPIO documentation on native functions available for certain pad.
|
|
If GPIO is set to one of NativeX modes then following settings are not applicable
|
|
and can be skipped:
|
|
- Interrupt related settings
|
|
- Host Software Ownership
|
|
- Output/Input enabling/disabling
|
|
- Output lock
|
|
**/
|
|
typedef enum {
|
|
GpioPadModeGpio = 0x1,
|
|
GpioPadModeNative1 = 0x3,
|
|
GpioPadModeNative2 = 0x5,
|
|
GpioPadModeNative3 = 0x7,
|
|
GpioPadModeNative4 = 0x9,
|
|
GpioPadModeNative5 = 0xB
|
|
} GPIO_PAD_MODE;
|
|
|
|
/**
|
|
Host Software Pad Ownership modes
|
|
This setting affects GPIO interrupt status registers. Depending on chosen ownership
|
|
some GPIO Interrupt status register get updated and other masked.
|
|
Please refer to EDS for HOSTSW_OWN register description.
|
|
**/
|
|
typedef enum {
|
|
GpioHostOwnDefault = 0x0, ///< Leave ownership value unmodified
|
|
/**
|
|
Set HOST ownership to ACPI.
|
|
Use this setting if pad is not going to be used by GPIO OS driver.
|
|
If GPIO is configured to generate SCI/SMI/NMI then this setting must be
|
|
used for interrupts to work
|
|
**/
|
|
GpioHostOwnAcpi = 0x1,
|
|
/**
|
|
Set HOST ownership to GPIO Driver mode.
|
|
Use this setting only if GPIO pad should be controlled by GPIO OS Driver.
|
|
GPIO OS Driver will be able to control the pad if appropriate entry in
|
|
ACPI exists (refer to ACPI specification for GpioIo and GpioInt descriptors)
|
|
**/
|
|
GpioHostOwnGpio = 0x3
|
|
} GPIO_HOSTSW_OWN;
|
|
|
|
///
|
|
/// GPIO Direction
|
|
///
|
|
typedef enum {
|
|
GpioDirDefault = 0x0, ///< Leave pad direction setting unmodified
|
|
GpioDirInOut = (0x1 | (0x1 << 3)), ///< Set pad for both output and input
|
|
GpioDirInInvOut = (0x1 | (0x3 << 3)), ///< Set pad for both output and input with inversion
|
|
GpioDirIn = (0x3 | (0x1 << 3)), ///< Set pad for input only
|
|
GpioDirInInv = (0x3 | (0x3 << 3)), ///< Set pad for input with inversion
|
|
GpioDirOut = 0x5, ///< Set pad for output only
|
|
GpioDirNone = 0x7 ///< Disable both output and input
|
|
} GPIO_DIRECTION;
|
|
|
|
/**
|
|
GPIO Output State
|
|
This field is relevant only if output is enabled
|
|
**/
|
|
typedef enum {
|
|
GpioOutDefault = 0x0, ///< Leave output value unmodified
|
|
GpioOutLow = 0x1, ///< Set output to low
|
|
GpioOutHigh = 0x3 ///< Set output to high
|
|
} GPIO_OUTPUT_STATE;
|
|
|
|
/**
|
|
GPIO interrupt configuration
|
|
This setting is applicable only if pad is in GPIO mode and has input enabled.
|
|
GPIO_INT_CONFIG allows to choose which interrupt is generated (IOxAPIC/SCI/SMI/NMI)
|
|
and how it is triggered (edge or level). Refer to PADCFG_DW0 register description in
|
|
EDS for details on this settings.
|
|
Field from GpioIntNmi to GpioIntApic can be OR'ed with GpioIntLevel to GpioIntBothEdge
|
|
to describe an interrupt e.g. GpioIntApic | GpioIntLevel
|
|
If GPIO is set to cause an SCI then also GPI_GPE_EN is enabled for this pad.
|
|
If GPIO is set to cause an NMI then also GPI_NMI_EN is enabled for this pad.
|
|
Not all GPIO are capable of generating an SMI or NMI interrupt.
|
|
When routing GPIO to cause an IOxAPIC interrupt care must be taken, as this
|
|
interrupt cannot be shared and its IRQn number is not configurable.
|
|
Refer to EDS for GPIO pads IRQ numbers (PADCFG_DW1.IntSel)
|
|
If GPIO is under GPIO OS driver control and appropriate ACPI GpioInt descriptor
|
|
exist then use only trigger type setting (from GpioIntLevel to GpioIntBothEdge).
|
|
This type of GPIO Driver interrupt doesn't have any additional routing setting
|
|
required to be set by BIOS. Interrupt is handled by GPIO OS Driver.
|
|
**/
|
|
|
|
typedef enum {
|
|
GpioIntDefault = 0x0, ///< Leave value of interrupt routing unmodified
|
|
GpioIntDis = 0x1, ///< Disable IOxAPIC/SCI/SMI/NMI interrupt generation
|
|
GpioIntNmi = 0x3, ///< Enable NMI interrupt only
|
|
GpioIntSmi = 0x5, ///< Enable SMI interrupt only
|
|
GpioIntSci = 0x9, ///< Enable SCI interrupt only
|
|
GpioIntApic = 0x11, ///< Enable IOxAPIC interrupt only
|
|
GpioIntLevel = (0x1 << 5), ///< Set interrupt as level triggered
|
|
GpioIntEdge = (0x3 << 5), ///< Set interrupt as edge triggered (type of edge depends on input inversion)
|
|
GpioIntLvlEdgDis = (0x5 << 5), ///< Disable interrupt trigger
|
|
GpioIntBothEdge = (0x7 << 5) ///< Set interrupt as both edge triggered
|
|
} GPIO_INT_CONFIG;
|
|
|
|
#define B_GPIO_INT_CONFIG_INT_SOURCE_MASK 0x1F ///< Mask for GPIO_INT_CONFIG for interrupt source
|
|
#define B_GPIO_INT_CONFIG_INT_TYPE_MASK 0xE0 ///< Mask for GPIO_INT_CONFIG for interrupt type
|
|
|
|
/**
|
|
GPIO Power Configuration
|
|
GPIO_RESET_CONFIG allows to set GPIO Reset type (PADCFG_DW0.PadRstCfg) which will
|
|
be used to reset certain GPIO settings.
|
|
Refer to EDS for settings that are controllable by PadRstCfg.
|
|
**/
|
|
typedef enum {
|
|
GpioResetDefault = 0x00, ///< Leave value of pad reset unmodified
|
|
/**
|
|
Resume Reset (RSMRST)
|
|
GPP: PadRstCfg = 00b = "Powergood"
|
|
GPD: PadRstCfg = 11b = "Resume Reset"
|
|
Pad setting will reset on:
|
|
- DeepSx transition
|
|
- G3
|
|
Pad settings will not reset on:
|
|
- S3/S4/S5 transition
|
|
- Warm/Cold/Global reset
|
|
**/
|
|
GpioResumeReset = 0x01,
|
|
/**
|
|
Host Deep Reset
|
|
PadRstCfg = 01b = "Deep GPIO Reset"
|
|
Pad settings will reset on:
|
|
- Warm/Cold/Global reset
|
|
- DeepSx transition
|
|
- G3
|
|
Pad settings will not reset on:
|
|
- S3/S4/S5 transition
|
|
**/
|
|
GpioHostDeepReset = 0x03,
|
|
/**
|
|
Platform Reset (PLTRST)
|
|
PadRstCfg = 10b = "GPIO Reset"
|
|
Pad settings will reset on:
|
|
- S3/S4/S5 transition
|
|
- Warm/Cold/Global reset
|
|
- DeepSx transition
|
|
- G3
|
|
**/
|
|
GpioPlatformReset = 0x05,
|
|
/**
|
|
Deep Sleep Well Reset (DSW_PWROK)
|
|
GPP: not applicable
|
|
GPD: PadRstCfg = 00b = "Powergood"
|
|
Pad settings will reset on:
|
|
- G3
|
|
Pad settings will not reset on:
|
|
- S3/S4/S5 transition
|
|
- Warm/Cold/Global reset
|
|
- DeepSx transition
|
|
**/
|
|
GpioDswReset = 0x07
|
|
} GPIO_RESET_CONFIG;
|
|
|
|
/**
|
|
GPIO Electrical Configuration
|
|
Configuration options for GPIO termination setting
|
|
**/
|
|
typedef enum {
|
|
GpioTermDefault = 0x0, ///< Leave termination setting unmodified
|
|
GpioTermNone = 0x1, ///< none
|
|
GpioTermWpd5K = 0x5, ///< 5kOhm weak pull-down
|
|
GpioTermWpd20K = 0x9, ///< 20kOhm weak pull-down
|
|
GpioTermWpu1K = 0x13, ///< 1kOhm weak pull-up
|
|
GpioTermWpu2K = 0x17, ///< 2kOhm weak pull-up
|
|
GpioTermWpu5K = 0x15, ///< 5kOhm weak pull-up
|
|
GpioTermWpu20K = 0x19, ///< 20kOhm weak pull-up
|
|
GpioTermWpu1K2K = 0x1B, ///< 1kOhm & 2kOhm weak pull-up
|
|
/**
|
|
Native function controls pads termination
|
|
This setting is applicable only to some native modes.
|
|
Please check EDS to determine which native functionality
|
|
can control pads termination
|
|
**/
|
|
GpioTermNative = 0x1F
|
|
} GPIO_ELECTRICAL_CONFIG;
|
|
|
|
#define B_GPIO_ELECTRICAL_CONFIG_TERMINATION_MASK 0x1F ///< Mask for GPIO_ELECTRICAL_CONFIG for termination value
|
|
|
|
/**
|
|
GPIO LockConfiguration
|
|
Set GPIO configuration lock and output state lock.
|
|
GpioPadConfigUnlock/Lock and GpioOutputStateUnlock can be OR'ed.
|
|
By default GPIO pads will be locked unless GPIO lib is explicitly
|
|
informed that certain pad is to be left unlocked.
|
|
Lock settings reset is in Powergood domain. Care must be taken when using this setting
|
|
as fields it locks may be reset by a different signal and can be controlled
|
|
by what is in GPIO_RESET_CONFIG (PADCFG_DW0.PadRstCfg). GPIO library provides
|
|
functions which allow to unlock a GPIO pad. If possible each GPIO lib function will try to unlock
|
|
an already locked pad upon request for reconfiguration
|
|
**/
|
|
typedef enum {
|
|
/**
|
|
Perform default action
|
|
- if pad is an GPO, lock configuration but leave output unlocked
|
|
- if pad is an GPI, lock everything
|
|
- if pad is in native, lock everything
|
|
**/
|
|
GpioLockDefault = 0x0,
|
|
GpioPadConfigUnlock = 0x3, ///< Leave Pad configuration unlocked
|
|
GpioPadConfigLock = 0x1, ///< Lock Pad configuration
|
|
GpioOutputStateUnlock = 0xC, ///< Leave Pad output control unlocked
|
|
GpioPadUnlock = 0xF, ///< Leave both Pad configuration and output control unlocked
|
|
GpioPadLock = 0x5 ///< Lock both Pad configuration and output control
|
|
} GPIO_LOCK_CONFIG;
|
|
|
|
#define B_GPIO_LOCK_CONFIG_PAD_CONF_LOCK_MASK 0x3 ///< Mask for GPIO_LOCK_CONFIG for Pad Configuration Lock
|
|
#define B_GPIO_LOCK_CONFIG_OUTPUT_LOCK_MASK 0xC ///< Mask for GPIO_LOCK_CONFIG for Pad Output Lock
|
|
|
|
/**
|
|
Other GPIO Configuration
|
|
GPIO_OTHER_CONFIG is used for less often settings and for future extensions
|
|
Supported settings:
|
|
- RX raw override to '1' - allows to override input value to '1'
|
|
This setting is applicable only if in input mode (both in GPIO and native usage).
|
|
The override takes place at the internal pad state directly from buffer and before the RXINV.
|
|
**/
|
|
typedef enum {
|
|
GpioRxRaw1Default = 0x0, ///< Use default input override value
|
|
GpioRxRaw1Dis = 0x1, ///< Don't override input
|
|
GpioRxRaw1En = 0x3 ///< Override input to '1'
|
|
} GPIO_OTHER_CONFIG;
|
|
|
|
#define B_GPIO_OTHER_CONFIG_RXRAW_MASK 0x3 ///< Mask for GPIO_OTHER_CONFIG for RxRaw1 setting
|
|
|
|
#pragma pack(pop)
|
|
|
|
#endif //_GPIO_CONFIG_H_
|