mb/google/nissa/var/glassway: Add initial override devicetree
Refer to the reference board of nivviks, and update devicetree settings via glassway schematic of ca24a_r10_240108_v3_mb_gsen_gmr.pdf. BUG=b:319071869 BRANCH=firmware-nissa-15217.B TEST=Local build successfully and boot to OOBE normally. Change-Id: Ibbb10a373bd5fa52a0833b81133517d2a088536b Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80742 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit is contained in:
Daniel Peng
Subrata Banik
parent
25b70d9326
commit
1aecff447d
@ -1,6 +1,496 @@
|
||||
chip soc/intel/alderlake
|
||||
|
||||
device domain 0 on
|
||||
end
|
||||
|
||||
fw_config
|
||||
field THERMAL_SOLUTION 0
|
||||
option THERMAL_SOLUTION_PASSIVE 0
|
||||
option THERMAL_SOLUTION_ACTIVE 1
|
||||
end
|
||||
field DB_USB 5 7
|
||||
option DB_NONE 0
|
||||
option DB_1C 1
|
||||
option DB_1A 2
|
||||
option DB_1C_1A 3
|
||||
end
|
||||
field SD_CARD 8
|
||||
option SD_ABSENT 0
|
||||
option SD_GL9750S 1
|
||||
end
|
||||
field TOUCHSCREEN_SOURCE 32 33
|
||||
option TOUCHSCREEN_UNPROVISIONED 0
|
||||
option TOUCHSCREEN_ELAN0001 1
|
||||
option TOUCHSCREEN_ELAN9008 2
|
||||
end
|
||||
end
|
||||
|
||||
chip soc/intel/alderlake
|
||||
register "sagv" = "SaGv_Enabled"
|
||||
|
||||
# SOC Aux orientation override:
|
||||
# This is a bitfield that corresponds to up to 4 TCSS ports.
|
||||
# Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2.
|
||||
# TcssAuxOri = 0101b
|
||||
# Bit0,Bit2 set to "1" indicates no retimer on USBC Ports
|
||||
# Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the
|
||||
# motherboard to USBC connector
|
||||
register "tcss_aux_ori" = "5"
|
||||
|
||||
register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
|
||||
register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}"
|
||||
|
||||
register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN
|
||||
|
||||
# Configure external V1P05/Vnn/VnnSx Rails
|
||||
register "ext_fivr_settings" = "{
|
||||
.configure_ext_fivr = 1,
|
||||
.v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0,
|
||||
.vnn_enable_bitmap = FIVR_ENABLE_ALL_SX,
|
||||
.vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX,
|
||||
.v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL,
|
||||
.vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE,
|
||||
.v1p05_voltage_mv = 1050,
|
||||
.vnn_voltage_mv = 780,
|
||||
.vnn_sx_voltage_mv = 1050,
|
||||
.v1p05_icc_max_ma = 500,
|
||||
.vnn_icc_max_ma = 500,
|
||||
}"
|
||||
|
||||
# Enable the Cnvi BT Audio Offload
|
||||
register "cnvi_bt_audio_offload" = "1"
|
||||
|
||||
# Intel Common SoC Config
|
||||
#+-------------------+---------------------------+
|
||||
#| Field | Value |
|
||||
#+-------------------+---------------------------+
|
||||
#| I2C0 | TPM. Early init is |
|
||||
#| | required to set up a BAR |
|
||||
#| | for TPM communication |
|
||||
#| I2C1 | Touchscreen |
|
||||
#| I2C2 | Sub-board(PSensor)/WCAM |
|
||||
#| I2C3 | Audio |
|
||||
#| I2C5 | Trackpad |
|
||||
#+-------------------+---------------------------+
|
||||
register "common_soc_config" = "{
|
||||
.i2c[0] = {
|
||||
.early_init = 1,
|
||||
.speed = I2C_SPEED_FAST_PLUS,
|
||||
.speed_config[0] = {
|
||||
.speed = I2C_SPEED_FAST_PLUS,
|
||||
.scl_lcnt = 55,
|
||||
.scl_hcnt = 30,
|
||||
.sda_hold = 7,
|
||||
}
|
||||
},
|
||||
.i2c[1] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.speed_config[0] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.scl_lcnt = 157,
|
||||
.scl_hcnt = 79,
|
||||
.sda_hold = 7,
|
||||
}
|
||||
},
|
||||
.i2c[2] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.speed_config[0] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.scl_lcnt = 157,
|
||||
.scl_hcnt = 79,
|
||||
.sda_hold = 7,
|
||||
}
|
||||
},
|
||||
.i2c[3] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.speed_config[0] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.scl_lcnt = 158,
|
||||
.scl_hcnt = 79,
|
||||
.sda_hold = 7,
|
||||
}
|
||||
},
|
||||
.i2c[5] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.speed_config[0] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.scl_lcnt = 158,
|
||||
.scl_hcnt = 79,
|
||||
.sda_hold = 7,
|
||||
}
|
||||
},
|
||||
}"
|
||||
|
||||
device domain 0 on
|
||||
device ref dtt on
|
||||
chip drivers/intel/dptf
|
||||
## sensor information
|
||||
register "options.tsr[0].desc" = ""Memory""
|
||||
register "options.tsr[1].desc" = ""Charger""
|
||||
register "options.tsr[2].desc" = ""Ambient""
|
||||
|
||||
# TODO: below values are initial reference values only
|
||||
## Passive Policy
|
||||
register "policies.passive" = "{
|
||||
[0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
|
||||
[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
|
||||
[2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000),
|
||||
[3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000),
|
||||
}"
|
||||
|
||||
## Critical Policy
|
||||
register "policies.critical" = "{
|
||||
[0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
|
||||
[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
|
||||
[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
|
||||
[3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN),
|
||||
}"
|
||||
|
||||
register "controls.power_limits" = "{
|
||||
.pl1 = {
|
||||
.min_power = 3000,
|
||||
.max_power = 6000,
|
||||
.time_window_min = 28 * MSECS_PER_SEC,
|
||||
.time_window_max = 32 * MSECS_PER_SEC,
|
||||
.granularity = 200
|
||||
},
|
||||
.pl2 = {
|
||||
.min_power = 25000,
|
||||
.max_power = 25000,
|
||||
.time_window_min = 1,
|
||||
.time_window_max = 1,
|
||||
.granularity = 1000
|
||||
}
|
||||
}"
|
||||
|
||||
## Charger Performance Control (Control, mA)
|
||||
register "controls.charger_perf" = "{
|
||||
[0] = { 255, 1700 },
|
||||
[1] = { 24, 1500 },
|
||||
[2] = { 16, 1000 },
|
||||
[3] = { 8, 500 }
|
||||
}"
|
||||
|
||||
device generic 0 on
|
||||
probe THERMAL_SOLUTION THERMAL_SOLUTION_PASSIVE
|
||||
end
|
||||
end
|
||||
chip drivers/intel/dptf
|
||||
## sensor information
|
||||
register "options.tsr[0].desc" = ""Memory""
|
||||
register "options.tsr[1].desc" = ""Charger""
|
||||
register "options.tsr[2].desc" = ""Ambient""
|
||||
|
||||
# TODO: below values are initial reference values only
|
||||
## Active Policy
|
||||
register "policies.active" = "{
|
||||
[0] = {
|
||||
.target = DPTF_CPU,
|
||||
.thresholds = {
|
||||
TEMP_PCT(85, 90),
|
||||
TEMP_PCT(80, 80),
|
||||
TEMP_PCT(75, 70),
|
||||
TEMP_PCT(70, 50),
|
||||
TEMP_PCT(65, 30),
|
||||
}
|
||||
},
|
||||
[1] = {
|
||||
.target = DPTF_TEMP_SENSOR_2,
|
||||
.thresholds = {
|
||||
TEMP_PCT(50, 90),
|
||||
TEMP_PCT(48, 70),
|
||||
TEMP_PCT(46, 60),
|
||||
TEMP_PCT(43, 40),
|
||||
TEMP_PCT(40, 30),
|
||||
}
|
||||
}
|
||||
}"
|
||||
|
||||
# TODO: below values are initial reference values only
|
||||
## Passive Policy
|
||||
register "policies.passive" = "{
|
||||
[0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
|
||||
[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
|
||||
[2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000),
|
||||
[3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000),
|
||||
}"
|
||||
|
||||
## Critical Policy
|
||||
register "policies.critical" = "{
|
||||
[0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
|
||||
[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
|
||||
[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
|
||||
[3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN),
|
||||
}"
|
||||
|
||||
register "controls.power_limits" = "{
|
||||
.pl1 = {
|
||||
.min_power = 12000,
|
||||
.max_power = 15000,
|
||||
.time_window_min = 28 * MSECS_PER_SEC,
|
||||
.time_window_max = 32 * MSECS_PER_SEC,
|
||||
.granularity = 200
|
||||
},
|
||||
.pl2 = {
|
||||
.min_power = 35000,
|
||||
.max_power = 35000,
|
||||
.time_window_min = 1,
|
||||
.time_window_max = 1,
|
||||
.granularity = 1000
|
||||
}
|
||||
}"
|
||||
|
||||
## Charger Performance Control (Control, mA)
|
||||
register "controls.charger_perf" = "{
|
||||
[0] = { 255, 1700 },
|
||||
[1] = { 24, 1500 },
|
||||
[2] = { 16, 1000 },
|
||||
[3] = { 8, 500 }
|
||||
}"
|
||||
|
||||
## Fan Performance Control (Percent, Speed, Noise, Power)
|
||||
register "controls.fan_perf" = "{
|
||||
[0] = { 100, 6000, 220, 2200, },
|
||||
[1] = { 92, 5500, 180, 1800, },
|
||||
[2] = { 85, 5000, 145, 1450, },
|
||||
[3] = { 70, 4400, 115, 1150, },
|
||||
[4] = { 56, 3900, 90, 900, },
|
||||
[5] = { 45, 3300, 55, 550, },
|
||||
[6] = { 38, 3000, 30, 300, },
|
||||
[7] = { 33, 2900, 15, 150, },
|
||||
[8] = { 10, 800, 10, 100, },
|
||||
[9] = { 0, 0, 0, 50, }
|
||||
}"
|
||||
|
||||
## Fan options
|
||||
register "options.fan.fine_grained_control" = "1"
|
||||
register "options.fan.step_size" = "2"
|
||||
|
||||
device generic 1 on
|
||||
probe THERMAL_SOLUTION THERMAL_SOLUTION_ACTIVE
|
||||
end
|
||||
end
|
||||
end
|
||||
device ref cnvi_wifi on
|
||||
chip drivers/wifi/generic
|
||||
register "enable_cnvi_ddr_rfim" = "true"
|
||||
device generic 0 on end
|
||||
end
|
||||
end
|
||||
device ref i2c1 on
|
||||
chip drivers/i2c/generic
|
||||
register "hid" = ""ELAN0001""
|
||||
register "desc" = ""ELAN Touchscreen""
|
||||
register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
|
||||
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
|
||||
register "reset_delay_ms" = "25"
|
||||
register "reset_off_delay_ms" = "4"
|
||||
register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
|
||||
register "stop_delay_ms" = "25"
|
||||
register "stop_off_delay_ms" = "2"
|
||||
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
|
||||
register "enable_delay_ms" = "7"
|
||||
register "has_power_resource" = "1"
|
||||
device i2c 10 on
|
||||
probe TOUCHSCREEN_SOURCE TOUCHSCREEN_UNPROVISIONED
|
||||
probe TOUCHSCREEN_SOURCE TOUCHSCREEN_ELAN0001
|
||||
end
|
||||
end
|
||||
chip drivers/i2c/hid
|
||||
register "generic.hid" = ""ELAN9008""
|
||||
register "generic.desc" = ""ELAN Touchscreen""
|
||||
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
|
||||
register "generic.detect" = "1"
|
||||
register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
|
||||
register "generic.reset_delay_ms" = "20"
|
||||
register "generic.reset_off_delay_ms" = "2"
|
||||
register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
|
||||
register "generic.stop_delay_ms" = "280"
|
||||
register "generic.stop_off_delay_ms" = "2"
|
||||
register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
|
||||
register "generic.enable_delay_ms" = "1"
|
||||
register "generic.has_power_resource" = "1"
|
||||
register "hid_desc_reg_offset" = "0x01"
|
||||
device i2c 10 on
|
||||
probe TOUCHSCREEN_SOURCE TOUCHSCREEN_ELAN9008
|
||||
end
|
||||
end
|
||||
end #I2C1
|
||||
device ref i2c3 on
|
||||
chip drivers/i2c/generic
|
||||
register "hid" = ""RTL5682""
|
||||
register "name" = ""RT58""
|
||||
register "desc" = ""Headset Codec""
|
||||
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
|
||||
# Set the jd_src to RT5668_JD1 for jack detection
|
||||
register "property_count" = "1"
|
||||
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
|
||||
register "property_list[0].name" = ""realtek,jd-src""
|
||||
register "property_list[0].integer" = "1"
|
||||
device i2c 1a on end
|
||||
end
|
||||
chip drivers/generic/alc1015
|
||||
register "hid" = ""RTL1019""
|
||||
register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
|
||||
device generic 1 on end
|
||||
end
|
||||
end #I2C3
|
||||
device ref i2c5 on
|
||||
chip drivers/i2c/generic
|
||||
register "hid" = ""ELAN0000""
|
||||
register "desc" = ""ELAN Touchpad""
|
||||
register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
|
||||
register "wake" = "GPE0_DW2_14"
|
||||
register "detect" = "1"
|
||||
device i2c 15 on end
|
||||
end
|
||||
end #I2C5
|
||||
device ref pcie_rp4 on
|
||||
# Enable wlan PCIe 4 using clk 2
|
||||
register "pch_pcie_rp[PCH_RP(4)]" = "{
|
||||
.clk_src = 2,
|
||||
.clk_req = 2,
|
||||
.flags = PCIE_RP_LTR | PCIE_RP_AER,
|
||||
}"
|
||||
chip drivers/wifi/generic
|
||||
register "add_acpi_dma_property" = "true"
|
||||
device pci 00.0 on end
|
||||
end
|
||||
end
|
||||
device ref pcie_rp7 on
|
||||
# Enable SD Card PCIe 7 using clk 3
|
||||
register "pch_pcie_rp[PCH_RP(7)]" = "{
|
||||
.clk_src = 3,
|
||||
.clk_req = 3,
|
||||
.flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
|
||||
}"
|
||||
chip soc/intel/common/block/pcie/rtd3
|
||||
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
|
||||
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)"
|
||||
register "srcclk_pin" = "3"
|
||||
device generic 0 on end
|
||||
end
|
||||
probe SD_CARD SD_GL9750S
|
||||
end
|
||||
device ref emmc on
|
||||
probe STORAGE STORAGE_EMMC
|
||||
end
|
||||
device ref ish on
|
||||
chip drivers/intel/ish
|
||||
register "add_acpi_dma_property" = "true"
|
||||
device generic 0 on end
|
||||
end
|
||||
probe STORAGE STORAGE_UFS
|
||||
end
|
||||
device ref ufs on
|
||||
probe STORAGE STORAGE_UFS
|
||||
end
|
||||
device ref pch_espi on
|
||||
chip ec/google/chromeec
|
||||
use conn0 as mux_conn[0]
|
||||
use conn1 as mux_conn[1]
|
||||
device pnp 0c09.0 on end
|
||||
end
|
||||
end
|
||||
device ref pmc hidden
|
||||
chip drivers/intel/pmc_mux
|
||||
device generic 0 on
|
||||
chip drivers/intel/pmc_mux/conn
|
||||
use usb2_port1 as usb2_port
|
||||
use tcss_usb3_port1 as usb3_port
|
||||
device generic 0 alias conn0 on end
|
||||
end
|
||||
chip drivers/intel/pmc_mux/conn
|
||||
use usb2_port2 as usb2_port
|
||||
use tcss_usb3_port2 as usb3_port
|
||||
device generic 1 alias conn1 on end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
device ref tcss_xhci on
|
||||
chip drivers/usb/acpi
|
||||
device ref tcss_root_hub on
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 Type-C Port C0 (MLB)""
|
||||
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
|
||||
device ref tcss_usb3_port1 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 Type-C Port C1 (DB)""
|
||||
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
|
||||
device ref tcss_usb3_port2 on end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
device ref xhci on
|
||||
chip drivers/usb/acpi
|
||||
device ref xhci_root_hub on
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Type-C Port C0 (MLB)""
|
||||
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
|
||||
device ref usb2_port1 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Type-C Port C1 (DB)""
|
||||
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
|
||||
device ref usb2_port2 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Type-A Port A0 (MLB)""
|
||||
register "type" = "UPC_TYPE_A"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
|
||||
device ref usb2_port3 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Type-A Port A1 (DB)""
|
||||
register "type" = "UPC_TYPE_A"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
|
||||
device ref usb2_port4 on
|
||||
probe DB_USB DB_1C_1A
|
||||
end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Camera""
|
||||
register "type" = "UPC_TYPE_INTERNAL"
|
||||
device ref usb2_port6 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Camera""
|
||||
register "type" = "UPC_TYPE_INTERNAL"
|
||||
device ref usb2_port7 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Bluetooth""
|
||||
register "type" = "UPC_TYPE_INTERNAL"
|
||||
register "reset_gpio" =
|
||||
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
|
||||
device ref usb2_port8 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 Type-A Port A0 (MLB)""
|
||||
register "type" = "UPC_TYPE_USB3_A"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
|
||||
device ref usb3_port1 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 Type-A Port A1 (DB)""
|
||||
register "type" = "UPC_TYPE_USB3_A"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
|
||||
device ref usb3_port2 on
|
||||
probe DB_USB DB_1C_1A
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user