This patch introduces CONFIG_I2C_TRANSFER_TIMEOUT_US,
which controls how long to wait for an I2C devices to
produce/accept all the data bytes in a single transfer.
(The device can delay transfer by stretching the clock of
the ack bit.)
The default value of this new setting is 500ms. Existing
code had timeouts anywhere from tens of milliseconds to a
full second beween various drivers. Drivers can still have
their own shorter timeouts for setup/communication with the
I2C host controller (as opposed to transactions with I2C
devices on the bus.)
In general, the timeout is not meant to be reached except in
situations where there is already serious problem with the
boot, and serves to make sure that some useful diagnostic
output is produced on the console.
Change-Id: I6423122f32aad1dbcee0bfe240cdaa8cb512791f
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
C1-state auto demotion feature allows hardware to determine C1-state as
per platform policy. Since Brya sets performance policy to balanced from
hardware, auto demotion can be disabled without performance impact.
Also, disabling this feature results in 110 mW power savings during
video playback.
Note that C1state Autodemotion feature is not applicable for ADL-P SoC.
Hence recommendation is to keep it disabled.
BUG=b:221876248
BRANCH=firmware-brya-14505.B
TEST=Code compiles and correct value of c1-state auto demotion is passed
to FSP. Also power and performance impact has been measure by respective
teams.
Change-Id: I41eea916cdfe4a86e4d263e3191f5cb40fa33a90
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
FSP has a parameter to enable/disable c1-state autodemotion feature.
Boards/Baseboard can choose to use this feature as per requirement.
This patch hooks up this parameter to devicetree
BUG=b:221876248
BRANCH=firmware-brya-14505.B
TEST=Check code compiles and correct value has been passed to FSP.
Change-Id: I2d7839d8fecd7b5403f52f3926d1d0bc06728ed9
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
coreboot chip.h files mainly contains variable which allows board to
fill platform configuration through devicetree.
Since many of this configuration involves FSP UPDs, variable names were
in camel case which aligned with UPD naming convention.
By default coreboot follow snake case variable naming, so cleaning up
file to align all variable names as per coreboot convention.
During renaming process, this patch also removes unused variables
listed below:
-> SataEnable // Checked in SoC code based on PCI dev enabled status
-> ITbtConnectTopologyTimeoutInMs // SoC always passes 0, so not used
Note: Since separating out changes into smaller CL might break the
compilation for the patch set, this is being pushed as a single big CL.
BUG=None
BRANCH=firmware-brya-14505.B
TEST=All boards using ADL SoC compiles with the CL.
Change-Id: Ieda567a89ec9287e3d988d489f3b3769dffcf9e0
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Commit hash b8b40964 ( mb, soc: Add the SPD_CACHE_ENABLE) introduced
per mainboard logic to invalidate the mrc_cache.
This patch moves mrc_cache invalidating logic into IA common code and
cleans up the code to remove unused argument `dimms_changed` from SoC
and mainboard directory.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6f18e18adc6572571871dd6da1698186e4e3d671
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
This patch adds `FSPM_UPD *` as argument for
mem_populate_channel_data() and read_spd_dimm().
This change will help to update the architectural FSP-M UPDs in
read_spd_dimm().
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I770cfd05194c33e11f98f95c5b93157b0ead70c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
This patch modifies `memcfg_init` and `variant_memory_init`functions
argument from FSP_M_CONFIG to FSPM_UPD.
This change in `memcfg_init()` argument will help to update the
architectural FSP-M UPDs from common code blocks rather than going
into SoC and/or mainboard implementation.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3002dd5c2f3703de41f38512976296f63e54d0c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Hoglin and Herobrine (proto1) should share majority of GPIOs.
Conslidating the QUP initializations in mainboard. Also, putting
fingerprint init in a conditional as not all devices will have an FP
sensor.
BUG=b:182963902,b:223826899
BRANCH=None
TEST=booted BIOS on hoglin and check for i2c errors in dmesg
Change-Id: I48ce42760f2c75f04619b967a05909d2b3f28e2c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Currently the BayHub eMMC enable pin is using the default
configuration from the baseboard, which leads to RTD3 not being able
to control the GPIO when exiting and entering suspend. To fix this,
program the GPIO in the ramstage GPIO table.
BUG=b:222436260
TEST=USE="project_primus" emerge-brya coreboot chromeos-bootimage
scope enable pin while performing suspend stress and enable pin
works as expected.
test suspend stress 1000 cycles passed on primus.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I1b6f164cc326bd368addb1e143ad2cbd449bb08d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
DDR4 SPD data needs to be 512 byte to comply with the spec.
Though there is no vital timing data used beyond 256 byte there are some
part information which will be used to show the part info in the
coreboot log. If the buffer is too small this log shows garbage.
This patch increases the SPD buffer size from 256 byte to 512 to avoid
side effects.
Change-Id: I5b88df7818cfd62b3579d69f9f5bb14880f49c8c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The patch implements error handling as per the ME BWG guide. The BWG
recommends HECI interface reset if there is a timeout or malformed
response is received from the CSE. Also, the patch triggers HECI
interface reset if the CSE link state is not ready in the heci_send()
API.
TEST=Verify HECI Interface reset in the simulated error scenarios.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I3e4a97800cbc5d95b8fd259e6e34a32fc82d8563
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The patch implements below changes:
1. Implements different error codes and use them in appropriate
failure scenarios of below functions:
a. heci_send()
b. recv_one_message()
c. heci_receive()
2. As heci_send_receive() is updated to return appropriate error codes
in different error scenarios of sending and receiving the HECI
commands. As the function is updated to return 0 when success, and
non-zero values in the failure scenarios, so all caller function have
been updated.
BUG=b:220652101
TEST=Verified CSE RX and TX APIs return error codes appropriately in
the simulated error scenarios.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ibedee748ed6d81436c6b125f2eb2722be3f5f8f0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The verstage.c file contains PSP verstage specific code. We don't need
it when using x86 verstage.
BUG=b:193050286
TEST=Build and boot guybrush with x86 verstage
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6dc928cdce0c922bb18f4479b993c89dff106070
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62740
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This sets EPP value to be 45% for all Brya variants.
Historically, EPP Ratio has always been 50% (128) on Chrome platforms.
But on Intel Alderlake EPP ratio of 45% is recommended for optimal
power and performance on Chrome platforms.
BUG=b:219785001
BRANCH=firmware-brya-14505.B
TEST=
Use 'iotools rdmsr [cpu id] 0x774' command and check field 32:24 = 0x73.
Signed-off-by: Cliff Huang <cliff.huang@intel.corp-partner.google.com>
Change-Id: I973cfec72a0be24c56c4cd3283d2fe6e18400d02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update PL1, PL2, and temperature sensor values from thermal team,
as well as, we remove unused temperature sensors according to
baseboard/devicetree.cb and mainboard schematic. After we check
DTT setting, the thermal and performance test pass.
BRANCH=dedede
BUG=b:204229229
TEST=on beadrix, run following commands:
localhost /tmp # cat /sys/class/thermal/thermal_zone*/type
x86_pkg_temp
INT3400 Thermal
TSR0
TSR1
TCPU
localhost /tmp # cat /sys/class/thermal/thermal_zone*/temp
45000
20000
32800
32800
39000
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: Ibc59c4aa431f600158e744f5bbdc6d59a07a1ef3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62729
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GFX HDA is the audio controller that provides audio output via the
external display connection, ACP is the audio coporcessor for the on-
board audio codec and XHCI2 is the third XHCI controller that provides
one USB 2.0 port. All those devices are used, so enable them in the
board's devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I186797a832470eb17752e06aa2fcc0b5c9db0398
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62571
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable pen garage. Pen detect is active low. And wake system when
eject.
BUG=b:223476974
TEST=evtest work as expected.
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "PRP0001:00"
Supported events:
Event type 0 (EV_SYN)
Event type 5 (EV_SW)
Event code 15 (SW_PEN_INSERTED) state 0
Properties:
Testing ... (interrupt to exit)
Event: type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: -------------- SYN_REPORT ------------
Event: type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I2f676301c3372a4760853ce9c10b75f94e22bbcd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This change mostly changes links that were identified as broken by
the 'website_scans' jenkins job.
There were some links that seem to be up at times, but that are
identified by link-checker as broken because of SSL issues.
At least one other link was changed to point to archive.org so
that it doesn't break at some point in the future. We should
probably try to make sure that everything is archived there and
point to those versions when possible.
There are still lots more links to do.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I36868ddf6113e18fa6841427dd635c75445b7bef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Only one ACPI device should be added to a PCIe root port. For the root
ports which already have device created, the generated code from this
driver needs to be merged with the existing device.
By default, this driver will create new device named DEV0.
This change allows to generate code under an existing device.
ex: (generate code under PXSX):
Scope (\_SB.PCI0.RP01.PXSX)
{
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package (0x01)
{
Package (0x02)
{
"UntrustedDevice",
One
}
}
})
}
BUG=b:221250331
BRANCH=firmware-brya-14505.B
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I80634bbfc2927f26f2a55a9c244eca517c437079
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Since the new loglevel markers were added, there will now be a marker
character at the beginning of the coreboot banner string, and this will
make the existing regular expressions meant to find it fail to match.
This patch fixes the problem by just allowing for a single extra
character there (any character to avoid the hassle of having to match
the marker explicitly). The extra character is optional so that we will
still continue to match banners from older versions of coreboot as well.
Since the `?` glyph is not available in basic POSIX regular expressions,
we have to switch to REG_EXTENDED syntax (should otherwise make no
difference). (Also, move side effects out of assert() while I'm here,
that's not actually safe for the standard libc implementation.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I99fb347eb1cf7b043a2113dfda7c798d6ee38975
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62720
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Get boot performance timestamps from CSE and inject them into CBMEM
timestamp table after normalizing to the zero-point value. Although
consumer CSE sku also supports this feature, it was validated on
CSE Lite sku only.
BUG=b:182575295
TEST=Able to see TS elapse prior to IA reset on Brya/Redrix
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 88,000
945:CSE started to handle ICC configuration 88,000 (0)
946:CSE sent 'Host BIOS Prep Done' to PMC 90,000 (2,000)
947:CSE received 'CPU Reset Done Ack sent' from PMC 282,000 (192,000)
0:1st timestamp 330,857 (48,857)
11:start of bootblock 341,811 (10,953)
12:end of bootblock 349,299 (7,487)
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Idcdbb69538ca2977cd97ce1ef9b211ff6510a3f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
In order to copy the PSP verstage logs into x86 cbmem, we need to enable
DEBUG_SMI. This will include the CBMEM console code in SMM. I only
enable DEBUG_SMI when UART is disabled because SMM doesn't currently
save/restore the UART registers. This will result in clearing the
interrupt enable bits and makes it so you can no longer use the TTY.
BUG=b:221231786, b:217968734
BRANCH=guybrush
TEST=Build serial and non serial firmware and verify DEBUG_SMI is set
correctly.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I85a7933e8eb49ff920d00e43a494aaeab555ef3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
