This patch introduces 3 helper function for cpuid(1) :
1. cpu_get_cpuid() -> to get processor id (from cpuid.eax)
2. cpu_get_feature_flags_ecx -> to get processor feature flag (from cpuid.ecx)
3. cpu_get_feature_flags_edx -> to get processor feature flag (from cpuid.edx)
Above 3 helper functions are targeted to replace majority of cpuid(1)
references.
Change-Id: Ib96a7c79dadb1feff0b8d58aa408b355fbb3bc50
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The kernel GPIO driver only expects some GPIO communities to be exported
in the _CRS and it will not work correctly if the other communities are
exported.
CNL-LP: GPIO communities 0, 1, 4
CNL-H: GPIO communities 0, 1, 3, 4
Additionally one of the pin offset values was incorrect in GPIO
community 1 for CNL-LP. This doesn't have any specific failure mode but
it was found when auditing the GPIO code.
Details of the kernel expected map can be found in the linux kernel at
drivers/pinctrl/intel/pinctrl-cannonlake.c
BUG=b:120686247
TEST=check /sys/kernel/debug/pinctrl/INT34BB:00/pins to ensure that
pins >= 198 are not reading all zeros for the pin config registers.
Change-Id: Ie1a2f3b9f9f4b24a9fc57e468dee50e99753912f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Recently there has been a change to print ME version. But the stage at
which the version is printed causes the HECI device to remain in D0 state.
This in turn prevents the SoC from entering S0ix state.
This change moves printing ME version a little earlier so that the HECI
device is put into D0i3 state by FSP and the SoC can enter S0ix state
successfully.
BRANCH=octopus
BUG=b:120571529
TEST=Ensure that the ME version gets printed in BIOS logs. Ensure that
the device boots to ChromeOS. Ensure that the device enters S0ix
successfully(using suspend_stress_test -c 25).
Change-Id: I85bc45003a040c8347f929457792d78a9a077c6c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The input clock for the I2C controllers was set at 133MHz but should
really be 216MHz according to the kernel:
https://patchwork.kernel.org/patch/10408729/
"Intel Cannon Lake PCH has much higher 216 MHz input clock to LPSS I2C
than Sunrisepoint which uses 120 MHz. Preliminary information was that
both share the same clock rate but actual silicon implements elevated
rate for better support for 3.4 MHz high-speed I2C."
This change was tested on a sarien board where an I2C trackpad that was
measuring ~700MHz on I2C and is now measuring ~380MHz.
Change-Id: I792d1f013da5538a2b8157e2f99b754ca7b6bf70
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30061
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As part of the memory mapped BIOS region is covered by SRAM, check
that CBFS always fits the effectively mapped region of flash. This
is usually taken care of by reserving the SRAM range in the FMAP
(e.g. as BIOS_UNUSABLE), but can be missed.
Change-Id: If5a5b553ad4853723bf13349c809c4f6154aa5f2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/30055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch does the following:
- improve the style by removing tabs in front of jmp addresses
- Make the code for zeroing variable MTRR more readable (copied from
cpu/intel/car)
- Fetch PHYSMASK high from cpuid instead of Kconfig
Change-Id: I6ba67bb8b049c3f25b856f6ebb1399d275764f54
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cache BIOS region can boost boot performance, however it can't be over
16MB, according to processor EDS vol1(Apollolake/Skylake/WhiskeyLake),
FLASH+APIC LT will be less than 20MB under 4G. Set the maxiam to 16GB
to save numbers of mtrr entries.
BUG=b:119267832
TEST=Build and boot up fine on whiskeylake rvp platform.
Change-Id: I46a47c8bf66b14fb2fcb7b6b1d30d02886c450a4
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the ACPI device names for the USB ports to match what
is in the DSDT so USB ports can be defined in the SSDT.
Change-Id: Ibb323bbd324811fa3178b0cba3d7f0a315169486
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Increase the bootblock size to 48K to match skylake. With UART
enabled we are very near the 32K limit, and with upcoming changes
to add USB devices in devicetree for a cannonlake board it is over
the current 32K limit.
Change-Id: I155cb0a6af1746af6833fa9f35c2ea6fe0bc709f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Define the constants that DPTF expects from the SOC in order to
use the common DPTF ACPI code. For cannonlake this indicates
the CPU device is called B0D4 and is at PCI address 00:04.0.
Change-Id: I43c2f8dd7281d3e9f791ab01478ee7823fd6b128
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29759
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a method to convert from 1/10 Kelvin to Celsius. This
is useful for EC devices where the sensor temperature are
stored in Celsius instead of Kelvin.
Change-Id: I6b1154f5ba13416131a029966d6d5c1598904881
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29758
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to support using the common ACPI code on more platforms
than just Apollo Lake the DPTF code needs to be told what the
PCI address is for the CPU thermal device.
Change-Id: I638f2387330bbc42f64eb0fb676ee32c5df6572e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29757
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Backlight control of internal panels likely won't work as configuration
for that seems absent in coreboot. Also, libgfxinit doesn't support any
MIPI/DSI connections, yet, and neither Gemini Lake.
TEST=Booted work-in-progress port kontron/mal10 with VGA text and
linear framebuffer modes. DP display came up.
Change-Id: I7b111f1cdac4d18f2fc3089f57aebf3ad1739e5d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29903
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds support to print ME version if UART_DEBUG is
enabled. Check for UART_DEBUG is necessary because talking to ME to
get the firmware version adds ~0.6 seconds to boot time.
TEST=Verified on octopus that ME version printed is correct.
Change-Id: I41217371558da1af694a2705e005429155d62838
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/29989
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sync the FSP settings with what coreboot does. Why both FSP and coreboot
configure this redundantly stays a secret.
TEST=Set SERIRQ_CONTINUOUS on kontron/mal10. A CPLD connected to LPC
works correctly now, but was confused by the wrong settings before
because the FSP defaults allowed to disable the LPC clock.
Change-Id: Id1c7180f460678bf0f9458228591050dd628c052
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Makes vboot measured boot mode available for all boards.
* Increase Tegra210 and Rockchip3228 SRAM for
romstage/verstage.
* Add missing files for Intel apollolake and
AMD stoneyridge as TPM driver target.
Change-Id: I35a85b8f137f28cd9960f2c5ce95f8fa31185b82
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Remove the __SIMPLE_DEVICE__ define from files used only in romstage.
This is not required since romstage always defines __SIMPLE_DEVICE__.
Change-Id: I8db1b15c9186536c9b8a6b5d667fa5a11af1bad2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29821
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
RAM is reserved for Chromeos even when Chrome is not used.
Use CONFIG_CHROMEOS to determine is RAM must be reserved.
BUG=N/A
TEST=Intel BayTrail CRB
Change-Id: Ic1f5089227f802e2b2f62dc02fa0d1648c1855b5
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Make pch_early_iorange_init() function similar to
soc/intel/cannonlake/bootblock/pch.c while fixing below issue:
* COM1 not being enabled properly.
TEST=Able to get serial output from an 8250IO UART device at
the standard 0x3f8 base address.
Change-Id: I5ab02f46d27e667be3d9328d94b634ef04038d2f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/29835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Using 0 for PIRQ_PIC_IRQDISABLE might conflict with using IRQ0 as PIRQ.
Change PIRQ_PIC_IRQDISABLE value to 0x80, so value 0 is reserved for IRQ0.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: I18706f12e7c2293e948eb10818393f0d1870f514
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29393
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The sizes of IO_BASE and ILB_BASE areas a incorrect.
Correct IO_BASE_SIZE and ILB_BASE_SIZE values.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: I23c3fd608598c5ec2271d393168ac4bf406772b4
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The resources of the local APIC are not reserved.
Use mmio_resource() to add local APIC resources.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: Ieb9de45098d507d59f1974eddb7a94cb18ef7903
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
ACPI and GPIO base are used by LPC controller, but not reserved.
Both bases are added to the LPC device resources.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: I5248694b497c4965d79dd7c25ec97592dc0dddbc
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
PL4 is a preemptive CPU package peak power limit,it will never be exceeded.
Power is preemptively lowered before limit is reached.
This change provides option in devicetree and feeds FSP PowerLimit4 UPD for
power limit purpose.
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Change-Id: I64b5a029104a102e5741e8b37c7992f2693180e8
Reviewed-on: https://review.coreboot.org/c/29808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
It's not implemented for Skylake, all combinations that try to enable it
either result in Kconfig or linker errors.
Move `config SKIP_FSP_CAR` into drivers/intel/fsp1_1 where it's
effective.
TEST=Built Intel/Kunimitsu (FSP1.1) and Intel/KBLRVP8 (FSP2.0) default
configs with and without this patch: binaries stay the same.
Change-Id: Iae0a2d2c7fd7a71ed24118564e6080c4789cda28
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
