Create the volet variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:186334008
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOLET
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ic6ca9a78494e3819b0fb39c0bcc70fed95c2c589
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Bank interleaving does not work on this platform, disable it.
Additionally enable ECC feature on SKUs supporting it. AmdIntPost
returns success thanks to these settings.
TEST=boot apu2 4GB ECC and apu3 2GB no ECC and see AGESA_SUCCESS after
AmdInitPost
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I010645f53b404341895d0545855905e81c89165e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
We need to configure CPU PCIE root port related gpios in early
boot block stage for CPU root ports to work. Since we're removing
this programming from FSP, coreboot needs to take care of programming
this GPIOs. Also we need to enable virtual wire messaging for native
gpios for CPU PCIE root ports.
Change-Id: Ieda6b6c31ce5bd5e84e4efe544bfc659283ce6f1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52270
Reviewed-by: Balaji Manigandan <balaji.manigandan@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On tgl, we noticed system hang if a shutdown is triggered before fsps.
The dut is unable to shutdown properly due to tcss is stuck before
tcss_init in fsps.
This change enable power button smi on jsl, tgl, adl after fsps.
it can also prevent a shutdown failure due to lack of fsps init on
certain ip.
BUG=b:186194102, b:186815114
TEST=Power on the system and pressing power button repeatedly doesn't
cause the system hang during shutdown.
Change-Id: I70b871f2676a89bc782116e02beba5c20ec51eef
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
If a power button SMI is triggered between where it is currently
enabled and before FSP-S exits, when the SMI handler disables
bus mastering for all devices, it inadvertently also disables
the PMC's I/O decoding, so the register write to actually go into
S5 does not succeed, and the system hangs.
This can be solved by skipping the PMC when disabling bus
mastering in the SMI handler, for which a callback,
smihandler_soc_disable_busmaster is provided.
BUG=b:186194102, b:186815114
TEST=Power on the system and pressing power button repeatedly doesn't
cause the system hang during shutdown.
Change-Id: I1cf5cf91ebad4a49df6679e01fc88ff60c81526c
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Mancomb uses DDR4 SODIMMs, but the default cezanne configuration is for
the LPDDR4 version. This changes to use SODIMMS.
Further changes may be needed for platform customization, so I put the
config file in variants/baseboard instead of the root mancomb directory.
BUG=b:187094481
TEST=Build only
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Icc4dc8aec2053cb177765f57e57cac7a099508fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
DISABLE_KEYBOARD_RESET_PIN - This pin goes to a test point and is not
used for the reset.
DRIVERS_UART_ACPI - Add the UART ACPI code
FW_CONFIG - Mancomb uses the firmware config interface
PSP_DISABLE_POSTCODES - The PSP is not yet initializing eSPI correctly
to send post codes to the EC, so disable them for now.
BUG=None
Test=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I39efcc8d1e0fb1e7ac0b0541a49db0ac0ee56481
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change fixes two problems:
1) We had the enum values for .direction and .level swapped. The naming
is very confusing...
2) ESPI_SYS is not a good event to use for EC SCI. It is a level/low
event that is only cleared by reading the eSPI status register 0x9C.
Cezanne has added a new event source that directly exposes the SCI bit.
This is the correct event source to use for EC SCI.
This same patch was added for Guybrush at CB:52673
BUG=b:186045622, b:181139095
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iac86d2ef5bdd21fbb0a0d4e235efe4fe621023b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52948
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using the push-pull alert was causing leakages when in S0i3. This is
because the EC drives ALERT#, so when the AP enters S0i3, the extra
current leaks into the SoC and ends up turning on the power regulators.
By using in-band ALERT#, the EC no longer drives this pin high, thus
fixing the leak. We could also have used an open drain alert, but the
rise time is less than ideal.
BUG=b:187122344, b:186135022
TEST=Measure S0i3 power on guybrush and validate it's no longer high.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6de771aeda8feca062652f0ea9eb57d31cb68562
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Some designs might wish to use an open drain eSPI ALERT#. This change
adds an enum that allows setting the eSPI alert mode.
BUG=b:187122344, b:186135022
TEST=Boot guybrush using all 3 alert modes
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia35fc59a699cf9444b53aad5c9bb71aa27ce9251
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The eSPI spec says that the Alert Mode defaults to in-band on reset.
This change ensures the controller is in sync with the eSPI peripheral.
The configured alert mode is configured in
espi_set_general_configuration.
BUG=b:187122344, b:186135022
TEST=Boot guybrush and make sure we don't get any eSPI errors.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib43e190d08d77ecfcd22ead2bf42e5de2202b555
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52953
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will print the config we are setting on the eSPI peripheral.
e.g.,
Setting general configuration: slave: 0x98a00000 controller: 0xe2000000
eSPI Slave configuration:
CRC checking enabled
Dedicated Alert# used to signal alert event
eSPI quad IO mode selected
Only eSPI single IO mode supported
Alert# pin is open-drain
eSPI 33MHz selected
eSPI up to 20MHz supported
Maximum Wait state: 0
BUG=b:187122344, b:186135022
TEST=Boot guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1a2382d8ab3d3f0d14a139c57470cb895112eca9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52952
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
None of the options accessed within coreboot is a string, and there are
no guarantees that the code works as intended with them. Given that the
current option API only supports integers for now, do not try to access
options whose type is 's' (string).
Change-Id: Ib67b126d972c6d55b77ea5ecfb862b4e9c766fe5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Do not use get_dram_base_mask to calculate system DRAM limits. Shift
operation around values operating on base and mask were causing
overflows and thus incorrect system DRAM limit. Another function
returning base and limit in KiB has been developed to avoid data loss.
Keep DRAM high base and limit in calculations only for Trinity where
the physical CPU address bits is 48. Although it is almost impossible
to have a non-zero value there, the platform would have to support
nearly 256GB of RAM.
TEST=boot PC Engines apu1 2GB, apu2 4GB and apu3 2GB and boot Debian
with Linux 4.14
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I3b5c1df96c308ff50c8de104e213219a98f25e10
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested on qemu/i440fx on X86_64:
- Page tables are found in cbfs (finding a file works)
- returns 0 when a file is not found
- works when there is no cbfs file at the start of the FMAP, e.g. with
the cbfs master header removed.
Change-Id: Ibab657cc40cd5c09c3a73c54950b98ac45a98dbf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52879
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TGL boards using the Type-C subsystem for USB Type-C ports without a
retimer attached may require a DC bias on the aux lines for certain
modes to work. This patch adds native coreboot support for programming
the IOM to handle this DC bias via a simple devicetree
setting. Previously a UPD was required to tell the FSP which GPIOs were
used for the pullup and pulldown biases, but the API for this UPD was
effectively undocumented.
BUG=b:174116646
TEST=Verified on volteer2 that a Type-C flash drive is enumerated
succesfully on all ports. Verified all major power flows (boot, reboot,
powerdown and S0ix/suspend) still work as expected.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I70e36a41e760f4a435511c147cc5744a77dbccc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The CPU can have its own Port IDs when addressing GPIO communities, which
differ from the PCH PCR IDs.
1) Add a field to `struct pad_community` that can hold this value when
known.
2) Add a function to return this value for a given GPIO pad.
Change-Id: I007c01758ae3026fe4dfef07b6a3a269ee3f9e33
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some SoCs may define virtual wire entries for certain GPIOs. This patch
allows SoC code to provide the mappings from GPIO pads to virtual wire
indexes and bits when they are provided. Also a function
`gpio_get_vw_info` is added to return this information.
Change-Id: I87adf0ca06cb5b7969bb2c258d6daebd44bb9748
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52588
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the pirika variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:184157747
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_PIRIKA
Signed-off-by: kirk_wang <kirk_wang@pegatron.corp-partner.google.com>
Change-Id: I57bf33deeadacc88800f9ce1d3d54385ba56c798
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52626
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adding GPIO definition for community 3 which is CPU reserved GPIO used
by CPU side PCIe root ports. We did not have this definition since
FSP used to program this GPIOs. Now, instead of FSP, coreboot programs
CPU PCIe GPIOs for CLKSRC and lanes to put GPIOs in native mode.
Thus adding definition of this virtual GPIOs in this CL.
BUG=None
BRANCH=None
TEST=Check if correct registers are being programmed
Change-Id: I481ea7e3ba948bf6d37b97d08c675a18ee68125d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
