Group event log state information together to manage them better during
different stages of coreboot.
BUG=b:117884485
BRANCH=None
TEST=Add an event log from romstage, boot to ChromeOS
Change-Id: I62792c0f5063c89ad11b512f1777c7ab8a2c13e5
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Make use of the common CF9 reset in SOC_INTEL_COMMON_RESET. Also
implement board_reset() as a "full reset" (aka. cold reset) as that
is what was used here for hard_reset().
Drop soc_reset_prepare() thereby, as it was only used for APL. Also,
move the global-reset logic.
We leave some comments to remind us that a system_reset() should
be enough, where a full_reset() is called now (to retain current
behaviour) and looks suspicious.
Note, as no global_reset() is implemented for Denverton-NS, we halt
there now instead of issuing a non-global reset. This seems safer;
a non-global reset might result in a reset loop.
Change-Id: I5e7025c3c9ea6ded18e72037412b60a1df31bd53
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change replaces use of post codes 0x34 and 0x36 in fsp drivers to
instead use POST_MEM_PREINIT_PREP_{START,END} to make it easy to
search from where these post codes are generated during boot flow.
Additionally, it adds POST_MEM_PREINIT_PREP_END to fsp2_0 memory_init
to make it consistent with fsp1_1 memory init.
Change-Id: I307ada1679f212c424e9f7ad2c9d254e24f41fd3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CPU_MICROCODE_CBFS_LEN and CPU_MICROCODE_CBFS_LOC configs pass the CPU
microcode length and base address in CBFS to FSPT binary as init parameters.
Add new config FSP_T_XIP in Kconfig, which is selected by platform config.
If FSP_T_XIP is selected, then relocate FSPT binary while adding it in CBFS
so that it can be executed in place.
BUG= None
TEST= Build for both CFL RVP11 & RVP8 and verified for successfull CAR setup.
Change-Id: Ic46e0bb9ee13c38ff322979119c4813653c61029
Signed-off-by: praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/28985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
A shortcoming of this driver is that if multiple devices with the same PCI ID
are present and don't have an eeprom, they would all get the same macadress set.
The r8168 driver deals with such cases so it should be easy to implement if
needed.
Change-Id: I5c32df00e25453c350a45e7f1ee6834b89c4289f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
With https://github.com/IntelFsp/FSP/pull/4 merged, this allows using
Intel's FSP repo (that we mirror) to build a complete BIOS ifd region
with a simple coreboot build, automatically drawing in headers and
binaries.
This commit covers Apollolake, Coffeelake, Skylake, and Kabylake.
Skylake is using Kabylake's FSP since its own is FSP 1.1 and Kabylake's
also supports Skylake.
Another candidate (given 3rdparty/fsp's content) is Denverton NS, but
it requires changes to coreboot's FSP bindings to become compatible.
Cannonlake, Whiskeylake require an FSP release.
Change-Id: I8d838ca6555348ce877f54e95907e9fdf6b9f2e7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28593
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change adds support in generic device driver to add properties to
DSD table. This driver can be used by all generic devices that do not
need any special handling other than simply adding device properties
to be used by OS.
BUG=b:112888584
Change-Id: I0ca6614f1ef322397618676bbf6da898bef18990
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28796
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per internal discussion, there's no "ChromiumOS Authors" that's
meaningful outside the Chromium OS project, so change everything to the
contemporary "Google LLC."
While at it, also ensure consistency in the LLC variants (exactly one
trailing period).
"Google Inc" does not need to be touched, so leave them alone.
Change-Id: Ia0780e31cdab879d2aaef62a2f0403e3db0a4ac8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Extend the generic flash interface to probe for write protected regions.
Add Winbond custom code to return flash protection.
Tested on Cavium EVB CN81xx using W25Q128.
Change-Id: I933a8abdc28174ec32acf323c102d606b58c1ea5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25082
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make XBCM `Serialized` (obvious), and check for the callee clearing the
request bit (we checked only the status for 0 which we potentially wrote
ourselves).
Change-Id: Ic92d525eda8d0a159fa5ddaacf230658d71c1578
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The device tree now supports 'hidden' and the status can be found in
`struct device.hidden`. A new acpi_device_status() will return the
expected setting of STA from a `struct device`.
BUG=b:72200466
BRANCH=eve
TEST=Builds and boots properly on device eve
Change-Id: I6dc62aff63cc3cb950739398a4dcac21836c9766
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/28567
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CBLV is not kept up to date by Linux' i915. We should fix that too,
but it will likely take some years until we can always expect it to
work.
For now read the register values directly. To accomodate that we
are not the only one writing those, revise XBQC() to search for
the closest value in BRIG (instead of a lower equal one) and round
more accurately for better matches.
Change-Id: I4e2d8fa34e75463d4cf7242af3e2c67577cfa2a5
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The SiFive UART on the HiFive Unleashed uses the tlclk as input clock
which runs at coreclk / 2.
The input frequency is configured in the board code depending on the
current stage. (bootblock + romstage run at 33.33Mhz, ramstage at 1Ghz)
Change-Id: Iaf66723dba3d308f809fde5b05dfc3e43f43bd42
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/27440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
FSP 2.1 implementation is adding features on top of fsp2_0.
One such feature is a shared stack implementation that requires
coreboot to allocate stack for fspm and then fsp uses the same
stack as coreboot. This implementation adds support for shared
stack feature.
Change-Id: I6581111dbaddfa403eca14100577ccc8a05c4ec7
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/28358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add CMOS option that allows to use both integrated and discrete GPU.
Tested on ThinkPad W530.
Change-Id: I8842fef0fa1235eb91abf6b7e655ed4d8598adc7
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/28393
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We should always update BCLP, no matter if the driver is ready yet to
process the request. This way it will hold the current value when the
driver initializes.
Change-Id: I4b091d744f95da39abe542966f0a8589a187573b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The _BCM function requires a percentage value. While the
brightness in mailbox3 requires a value in uint8_t. Meaning 255 = 100%.
Previous implementation stored the percentage brightness value resulting
in limiting the brightness to ~40% of it's maximum power.
Only affects brightness control using mailbox3.
Fixes: 6838aaebf9 ("drvs/intel/gma/acpi: Add methods to use MBOX3")
Change-Id: I290b5f5b2a8ee406e39e86d3e0de9997798d890d
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/28345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Bayhub eMMC controller default runs SD base 50MHz at the first power on.
After boot into OS, mmc kernel driver will config controller to HS200/208MHz
and send MMC CMD21 (tuning block).
But Bayhub PCR register 0x3E4[22] (eMMC MODE select) is not clear
after system warm reset.
So eMMC will still run 208Mhz but there is no block tuning cmd in depthcharge.
It will cause two Sandisk eMMC (SDINBDA4-64G-V/SDINBDA4-32G-V) to fail to
load kernel and trap in 0x5B error (No bootable kernel found on disk).
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: Ic080682e67323577c7f0ba4ed08f8adafca620cc
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This open-codes flash_cmd, but until the API is fixed for real, it uses
xfer's existing scatter-gather ability to write command and data in one
go.
BUG=chromium:446201
TEST=emerge-coral coreboot succeeds
Change-Id: Ic81b7c9f7e0f2647e59b81d61abd68d36051e578
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For debug reasons, sometimes you not only want to log an event, but also
some extra information that would help debugging. Create an extended event
reporting event type with a dword complement, and define extended events
for failing to enter S3 due to pending wake event (one for pm1 and one for
gpe0).
BUG=b:111100312
TEST=Add a fake pending wake event, build and boot grunt, see the event in
eventlog.txt.
Change-Id: I3e8df0953db09197d6d8145b0fc1e583379deaa5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
* Fix ACPI resume path compilation for TPM ramstage
driver
* Move enabling of the TPM prior activation and remove
reboot return status from TPM enable.
More information can be found via the TCG
specification v1.2
Tested=Elgon
Change-Id: Ided110e0c1889b302e29acac6d8d2341f97eb10b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/28085
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Under some conditions, cr50_i2c_read() can return without actually reading
the TPM, which will leave access uninitialized. Set an initial value for
access, and if TPM fails to respond in time check if at least TPM was read.
This way avoids printing an uninitialized value.
BUG=b:112253891
TEST=Build and boot grunt.
Change-Id: I5ec7a99396db32971dc8485b77158d735ab1d788
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
