TEST=Make the printk reachable, check with
`strings build/cbfs/fallback/romstage.elf | grep lowest`
that this patch changes "MHzas" to "MHz as".
Change-Id: I42033d2f184e424818edf844cf6cf84ea07d7ed5
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/29346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
On an ASRock H81M-HDS neither libgfxinit, nor Linux, is able to
initialise the display when lanes are not configured to be shared
between DDI A and DDI E.
Intel's reference manual [1] states that the decision to share lanes
between DDI A and DDI E is "based on board configuration". Hence, add a
new field to the devicetree that boards can set. All existing Haswell
boards have this unset, thus taking a value of 0, so there is no change
to existing behaviour.
[1]: Intel Open Source Graphics Programmer's Reference Manual (PRM)
Volume 2c: Command Reference: Registers (Haswell)
https://01.org/linuxgraphics/documentation/hardware-specification-prms/2013-intel-core-processor-family
Change-Id: I6f7832293215d2b53e31b0a5c985e6098eb72f1b
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/29385
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
8M was set in the assumption that at least 4M was needed for IED
(Intel Enhanced Debug) , but this is not true.
The SMRR MTRR's need to have TSEG aligned to its size which is easier when TSEG
is only 2M. Also at most 6M of RAM more becomes available for use.
Change-Id: I4b114c8dc13699b3c034f0a7060181d9d590737b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27873
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Having cbmem floating between two ram regions is a bad idea and some
payloads (e.g. tianocore) even bail out on this. To overcome this issue mark the
region between tom and cbmem as uma.
Change-Id: Ifab37b0003f09a680024d5b155ab0bb157920952
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add SOUTHBRIDGE_INTEL_COMMON_RESET for all Intel platforms that used to
perform a "system reset" in their hard_reset() implementation. Replace
all duplicate CF9 reset implementations for these platforms.
Change-Id: I8e359b0c4d5a1060edd0940d24c2f78dfed8a590
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
While during the read training itself only the settings for rank 0 are used for
all ranks, the controller does use the separate settings for each rank later on.
It is unknown which register is responsible for this.
The signals are probably not generated separately and therefore need to have the
same settings for all ranks. Therefore program the results for all ranks instead
of for all populated ranks.
TESTED: Fixes DG43GT not booting with only the second DIMM slot of a channel
populated.
Change-Id: I7965a068ef4779847e62e966154764370c91302a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28577
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Bounce buffers used to be used in those cases where the payload
might overlap coreboot.
Bounce buffers are a problem for rampayloads as they need malloc.
They are also an artifact of our x86 past before we had relocatable
ramstage; only x86, out of the 5 architectures we support, needs them;
currently they only seem to matter on the following chipsets:
src/northbridge/amd/amdfam10/Kconfig
src/northbridge/amd/lx/Kconfig
src/northbridge/via/vx900/Kconfig
src/soc/intel/fsp_baytrail/Kconfig
src/soc/intel/fsp_broadwell_de/Kconfig
The first three are obsolete or at least could be changed
to avoid the need to have bounce buffers.
The last two should change to no longer need them.
In any event they can be fixed or pegged to a release which supports
them.
For these five chipsets we change CONFIG_RAMBASE from 0x100000 (the
value needed in 1999 for the 32-bit Linux kernel, the original ramstage)
to 0xe00000 (14 Mib) which will put the non-relocatable x86
ramstage out of the way of any reasonable payload until we can
get rid of it for good.
14 MiB was chosen after some discussion, but it does fit well:
o Fits in the 16 MiB cacheable range coreboot sets up by default
o Most small payloads are well under 14 MiB (even kernels!)
o Most large payloads get loaded at 16 MiB (especially kernels!)
With this change in place coreboot correctly still loads a bzImage payload.
Werner reports that the 0xe00000 setting works on his broadwell systems.
Change-Id: I602feb32f35e8af1d0dc4ea9f25464872c9b824c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/28647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
As per internal discussion, there's no "ChromiumOS Authors" that's
meaningful outside the Chromium OS project, so change everything to the
contemporary "Google LLC."
While at it, also ensure consistency in the LLC variants (exactly one
trailing period).
"Google Inc" does not need to be touched, so leave them alone.
Change-Id: Ia0780e31cdab879d2aaef62a2f0403e3db0a4ac8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Using the cached CPU FSB setting can simply be wrong, in which case it won't
boot. Since the selected timings also depend on the CPU FSB, it is also best to
not use cached timings at all when a change is detected.
Tested on P5QC, swapped a 1333MHz FSB to a 800MHz FSB and it uses !fast_boot
boot path.
Change-Id: I12d91d0e892c15778409d7c00b27652ee52ca80c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add a __always_inline macro that wraps __attribute__((always_inline))
and replace current users with the macro, excluding files under
src/vendorcode.
Change-Id: Ic57e474c1d2ca7cc0405ac677869f78a28d3e529
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/28587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@google.com>
There's nothing Sandy Bridge specific in this code.
Make it available on all platforms to reduce code duplication.
Tested on Lenovo T430: SMBIOS entry 17 is still valid.
Change-Id: I051c3e07a999d8dad082c24f65b43dce180349fd
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/28213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
When doing the receive enable training, the final mapping of the ranks is
already done, so we can be sure that that address 0x00000000 there will always
be a rank.
Change-Id: I7ac017a8816fc9a47cef0695826a1c32f699f6f8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
