Major changes:
1. Separate resource allocation into:
A. Read Resources
B. Avoid fixed resources (constrain limits)
C. Allocate resources
D. Set resources
Usage notes:
Resources which have IORESOURCE_FIXED set in the flags constrain the placement
of other resources. All fixed resources will end up outside (above or below)
the allocated resources.
Domains usually start with base = 0 and limit = 2^address_bits - 1.
I've added an IOAPIC to all platforms so that the old limit of 0xfec00000 is
still there for resources. Some platforms may want to change that, but I didn't
want to break anyone's board.
Resources are allocated in a single block for memory and another for I/O.
Currently the resource allocator doesn't support holes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4394 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
targets/supermicro/h8dmr/Config.lb and Config-abuild.lb.
Importantly, this also sets
default CONFIG_AP_CODE_IN_CAR=0
in
src/mainboard/supermicro/h8dmr/Options.lb
which is required to make this box boot since the changes that went in in
r4315.
At Myles' suggestion, this patch also sets
default CONFIG_USE_FAILOVER_IMAGE=0
default CONFIG_USE_FALLBACK_IMAGE=0
default CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
in src/mainboard/supermicro/h8dmr/Options.lb to simplify
targets/supermicro/h8dmr/Config.lb a bit further.
Build tested with abuild, boot tested on physical hardware.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4393 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Thanks to Thomas Jourdan <thomas.jourdan@gmail.com> for reporting it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4391 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4389 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
didn't build before, and it still doesn't)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Attached is the third revision of the CN400/EPIA-N(L) patch for CB V2.
Patch should work against r4381 (or later ?)
This version now boots all of the way through to attempting to launch a
payload (I'm trying FILO right now), where it falls over with exception
6 (invalid opcode)
The coreboot_table issue seems to have been automagically resolved by
the latest core files.
It may still be that the reason for the payload not starting is down to
some issue with the tables initialising, I'll look closer at that.
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4386 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Coreboot used to take SYSTEM_TYPE as a lable to tell what the socket is.
This patch replaces (some of, not all) CONFIG_SYSTEM_TYPE with CONFIG_SOCKET_TYPE.
It also fix some compiling error in src/northbridge/amd/amdmct/mct/mctardk4.c
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4385 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Kconfig)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4384 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's basically done with the following script and some manual fixup:
VARS=`grep ^define src/config/Options.lb | cut -f2 -d\ | grep -v ^CONFIG | grep -v ^COREBOOT |grep -v ^CC`
for VAR in $VARS; do
find . -name .svn -prune -o -type f -exec perl -pi -e "s/(^|[^0-9a-zA-Z_]+)$VAR($|[^0-9a-zA-Z_]+)/\1CONFIG_$VAR\2/g" {} \;
done
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4381 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Its used for Name and Scope and Processor now. As bonus, it allows to
create a multi name paths too. Like Scope(\ALL.YOUR.BASE).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4368 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4366 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, enable HIGH_TABLES support for this board.
The HIGH_TABLES failed with:
No matching ram area found for range:
[0x00000000000f0000, 0x0000000000100000)
Ram areas
[0x0000000000000000, 0x0000000000001000) Reserved
[0x0000000000001000, 0x00000000000a0000) RAM
[0x0000000000100000, 0x000000000fff0000) RAM
[0x000000000fff0000, 0x0000000010000000) Reserved
SELFBOOT RETURNED!
Boot failed.
The fix was to change northbridge.c as follows:
- ram_resource(dev, idx++, 1024, tolmk - 1024);
+ ram_resource(dev, idx++, 768, tolmk - 768);
This is build-tested and tested on hardware by me. It boots fine,
for instace with SeaBIOS and the standard GRUB1 from my disk.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4365 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add initial ACPI support for M57SLI.
Activates/Enables:
* native Coreboot ACPI for M57SLI
* Soft-Power-Off
* PowerNow!
* High Precision Event Timer
* Windows booting with ACPI support
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4364 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
updating the passed value to the next link offset even when it was on the
requested link (cap_count).
Maximilian also found a bug where the linktype was still getting attributes
even when it wasn't initialized.
This should fix the HT problems for Fam10 C2. There are still issues with the
microcode which need to be resolved.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4358 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ways superior to v3, while lacking its completeness. But, one nice
thing: no more included .S or .c files. It's all separate compilation.
That should allow our Makefiles to work much better.
Note that the current non-CAR implementation is the default and
continues to work (tested FILO boot to Linux on both CAR and non-CAR).
Index: src/mainboard/emulation/qemu-x86/Config.lb
Change this to be sensitive to USE_DCACHE_RAM. All settings etc. that
depend on this variable are grouped in one if, and the other parts
(romcc etc.) are in the else. This change is a model of how we should be
able to do other motherboards.
Index: src/mainboard/emulation/qemu-x86/Options.lb
add needed options.
Index: src/mainboard/emulation/qemu-x86/failover.c
remove code inclusion from this not-yet-used file.
Index: src/mainboard/emulation/qemu-x86/rom.c
This is the entry point for the rom-based code. Called stage1.c in v3.
Index: src/lib/Config.lb
change initobject to a .o from a .c; this fixed a build problem.
Index: src/pc80/serial.c
make uart_init non-static.
Index: src/pc80/Config.lb
add initobject
Index: src/arch/i386/init/entry.S
Entry point. Unify a bunch of files that were fiddly lttle includes. From v3.
Index: src/arch/i386/init/ldscript.ld
new file. The goal is to hang all init changes for CAR here, to minimize other changes to any
other ldscript. Besides, putting this in init makes sense; entry and car are manage init.
Index: src/arch/i386/init/car.S
generic i386 car code from v3.
Index: src/arch/i386/init/ldscript_fallback_cbfs.lb
Fix what looks like a bug: this was not including the init.text section.
Index: targets/emulation/qemu-x86/Config.lb
push up the console loglevel. qemu is for debugging so we might as well
get all the debugging we can.
Index: targets/emulation/qemu-x86/Config-car.lb
For CAR bullds.
Signed-off-by: Ronald G. minnich <rminnich@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4357 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Abuild tested and boot tested on s2895 and serengeti_cheetah.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4355 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
gets us through config, but it fails during build because the original patch
duplicated some files for VIA systems.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4354 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
if it is already in its correct location.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4353 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Make get_dsdt script executable.
- Rename DrivingClkPhaseData.c to driving_clk_phase_data.c.
- Set proper IRQ_SLOT_COUNT value in the hope that the '14' from irq_table.c
is correct.
- Fix broken or incorrect #include names to increase likelyhood of a
successful compile.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4350 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
files for targets without failover:
src/config/nofailovercalculation.lb (64 kB XIP)
src/config/nofailovercalculation128.lb (128 kB XIP)
Targets with other XIP sizes were ignored.
This patch moves XIP size back into mainboard code.
Benefits from this patch:
- src/config/nofailovercalculation128.lb is no longer needed
- Targets with XIP sizes besides 64k and 128k benefit from refactoring
- Conceptually, this makes the include files pure calculation files
without settings.
Abuild tested.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4348 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
same. The errata need some extra room in failover.
Trivial and abuild tested
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4347 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Compared to posted patch, there are whitespace fixes
(request by Uwe), and a guard to run the erratum only
on AMD_RB_C2 (request by Marc).
Signed-off-by: Marco Schmidt <mashpb@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4346 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
instead of coreboot.strip. That fixes the normal
image because the calculations for its offset in
the ROM match reality again.
This requires changes in CBFS configurations to
minimize the bootblock size. These are also done
for CBFS boards.
Other than this a couple of minor fixes are in this
patch:
- make asus/m2v-mx_se build with abuild with a
crosscompiler
- move CONFIG_CBFS for hp/dl145_g3 to Options.lb
as it's done everywhere else
- change the default config of abuild to not
provide ROM_IMAGE_SIZE values for the images
in a CBFS configuration
- change abuild's crosscompile autodetection to
not try to use "i386-elf-i386-elf-gcc" (which
is bogus)
Except for the latter two abuild changes (both
in util/abuild/abuild), they're available as
patch set on the mailing list in a mail from
2009-06-05 titled
[PATCH]es to get normal image to work again with CBFS
The changes in util/abuild/abuild are trivial and
abuild tested.
As discussed on the list,
targets/hp/dl145_g3/Config-abuild.lb is
deleted, now that Config.lb works again.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4344 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The patch has been submitted by bari <bari@onelabs.com> and written
by OLPC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4342 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
them a bit more verbose and hopefully more understandable.
Old messages for my machine with 5 GB:
RAM: 0x00400000 kB
Ram3
[...]
Initializing memory: done
RAM: 0x00500000 kB
New messages:
RAM end at 0x00400000 kB
Adjusting lower RAM end
Lower RAM end at 0x003f0000 kB
Ram3
[...]
Initializing memory: done
Handling memory hole at 0x00300000 (default)
RAM end at 0x00500000 kB
Handling memory mapped above 4 GB
Upper RAM end at 0x00500000 kB
Correcting memory amount mapped below 4 GB
Adjusting lower RAM end
Lower RAM end at 0x00300000 kB
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4341 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Any endless loop after die() can be eliminated.
Dereferencing a NULL pointer is bad. die() instead.
Replace endless loops with die().
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4340 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
starts to play its role. Then the system hangs at HDA init. I dont know what the
VC1 is. The RPR says "Optional Features (only needed if CMOS option is enabled)"
in 5.10.2. Before I know what it is, I think it is better to skip it.
Tested on dbm690t.
Add comment from Rudolf,
"
VC is virtual channel. Its used for isochronous transfer of data to sound card.
The virtual channel guarantee "on time" delivery. In other words it sets up a
channel for data to sound card, which means that that arrivs in time and there will
be no interuptions in audio stream.
http://www.microsoft.com/whdc/connect/pci/wlp_interrupt.mspx
"
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4339 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
function based on test results with many different DIMMs.
Tested by Uwe Hermann <uwe@hermann-uwe.de> on hardware.
Might need a small increase of ROM_IMAGE_SIZE for some boards, we'll see.
Signed-off-by: Elia Yehuda <z4ziggy@gmail.com>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4338 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code, specifically the difference between pre_f and f code.
The only functional changes are in printk statements. The rest is white space.
1. Remove some #if 0 and #if 1 blocks
2. Remove #if USE_DCACHE_RAM blocks. All K8 boards use CAR.
2. Correct typos (canidate -> candidate)
3. Try to minimize the differences between amdk8_f.h and amdk8_pre_f.h
4. Try to minimize the differences between raminit.c and raminit_f.c
5. Make boards that have rev_f processors include the correct raminit code
There is much more that could be done, but it's a start.
Abuild tested and boot tested on s2892 and serengeti_cheetah.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4337 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. In rs690_cmn.c, mask the lower 4 bits of the BAR3. No doubt, right?
2. In rs690_pcie.c,
(1) Obviously, the mask should be 0xF, and bit 19 should be set to 1 (in comment).
In rpr 5.10.2, step 2, step 2.1 & step 2.6
(2) The dynamic buffer allocation is enabled by setting bit 11 of PCIEIND: 0x20,
instead of PCIEIND_P: 0x20.
In rpr 5.10.2, step 5. Dynamic Slave CPL Buffer Allocation
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4336 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This reverts commit eb7bb49eb5b48c39baf7a256b7c74e23e3da5660.
Stepan pointed out that "s" means string, which makes the following statement
in this commit message invalid: "Since we either have reserved space (which
we shouldn't do anything with in these two functions), an enum or a
hexadecimal value, unsigned int seemed like the way to go."
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Luc Verhaegen <libv@skynet.be>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4335 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This reverts commit c03527377db5951f0d3228e2a93b4c57dd81b8ec.
Stepan pointed out that 's' means string, and that therefor strings do exist.
Marking this as reserved breaks some payloads.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Luc Verhaegen <libv@skynet.be>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4334 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The kontron 986lcd_m cmos.layout had a 512bit area claimed for "boot_devices".
The changes to the cmos code no longer allow usage of values larger than
32bits. Since this option was completely unused, mark it as reserved.
Fixes build after the get_option change (r4332)..
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Luc Verhaegen <libv@skynet.be>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4333 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
To ease some of my debugging pain on the unichrome, i decided i needed to
move FB size selection into cmos, so i could test a size and then reset it
to the default after loading this value so that the next reboot uses the
(working) default again. This meant implementing set_option in parallel to
get_option.
get_option was then found to have inversed argument ordering (like outb) and
passing char * and then depending on the cmos layout length, which made me
feel quite uncomfortable. Since we either have reserved space (which we
shouldn't do anything with in these two functions), an enum or a
hexadecimal value, unsigned int seemed like the way to go. So all users of
get_option now have their arguments inversed and switched from using ints
to unsigned ints now.
The way get_cmos_value was implemented forced us to not overlap byte and to
have multibyte values be byte aligned. This logic is now adapted to do a
full uint32_t read (when needed) at any offset and any length up to 32, and
the shifting all happens inside an uint32_t as well. set_cmos_value was
implemented similarly. Both routines have been extensively tested in a
quick separate little program as it is not easy to get this stuff right.
build_opt_tbl.c was altered to function correctly within these new
parameters. The enum value retrieval has been changed strol(..., NULL, 10)
to stroul(..., NULL, 0), so that we not only are able to use unsigned ints
now but so that we also interprete hex values correctly. The 32bit limit
gets imposed on all entries not marked reserved, an unused "user_data" field
that appeared in a lot of cmos.layouts has been changed to reserved as well.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4332 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
directory just with one common file.
Changes to FADT: move to rev4, fix the generic register descriptors, detect additional VT8237S features.
Change the compiler to CORE , its revision to 42.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4327 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
out. Fix the libgcc dependency on abort() due to nested functions.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4326 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4325 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4324 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
