Add support for a mmio resource in the devicetree to allow
memory-mapped IO addresses to be assigned to given values.
AMD platforms perform a significant amount of configuration through
these MMIO addresses, including I2C bus configuration.
BUG=b:72121803
Change-Id: I5608721c22c1b229f527815b5f17fff3a080c3c8
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
3rdparty/blobs was updated to move northbridge/amd/00670F00 contents into
soc/amd/stoneyridge. Now soc/amd/stoneyridge/Kconfig needs to be updated
to use VBIOS.bin new location.
BUG=b:70785272
TEST=Update 3rdparty/blobs master branch, try to build kahlee. It should
fail. Update soc/amd/stoneyridge/Kconfig, try to build kahlee again, it
should work (need to rebuild .config first).
CQ-DEPEND=CL:881709
Change-Id: I8cb9874eedc4a5d41d42b3f727c6d3cb9b920b5a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This change disables SATA controller in order to make SATA IP enter
low power status.
BUG=b:72332817
TEST=cat /sys/kernel/debug/pmc_core/pch_ip_power_gating_status
and verify SATA IP enters low power state
Change-Id: I72a98bc3d0b47aebc0d7be534f4a7503084b257f
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23354
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This moves the call to pch_enable_lpc() from romstage to bootblock.
In other words, it happens earlier in the boot process. Turns out, we
need this to talk to the EC to determine if we're in recovery mode or
not.
BUG=b:69011806
TEST=boots to linux
Change-Id: I899bf343d705fe19a2978917bc88990495ebb5a3
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The FSP 2.0 Memory_Info_HOB for KBL is not sending
"MemoryType" value as what is required for SMBIOS Table
according to SMBIOS Spec. Thus, converting the value
retrieved from FSP HOB to the correct value.
This change will not be required for upcoming SOCs since
FSP have fixed this issue in its next platforms and thus it
will take care and send the correct value in "MemoryType"
field based on SMBIOS spec. Thus this conversion from coreboot
will not be required in the next platfoms. "MemoryType" value
can be directly passed to dimm_info_fill() function.
BUG=none
BRANCH=none
TEST=Tested in Soraka, and getting the value as 0x1D for
LPDDR3 memory. dmidecode (latest version 3.1) Command Type 17
will also show correct information. Currently, it was showing
"Unknown".
Change-Id: I75d6cca464680a88bf836e25bf5440a9cdbc738e
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/23384
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The TSC has been observed to be ticking at a non-constant rate
in early boot. The root cause is still not known, but this
misbehavior necessitates an alternative monotonic timer source.
Use the perf TSC which ticks at 100 MHz. This also means the
timestamp table is not accurate as well. Root cause of TSC rate
instability needs to be resolved in order to fix that.
BUG=b:72170796
Change-Id: Ie052169868a9d9f25f8cc0ce8dd8251b560e671f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
For the internal eMMC to be used by non-chrome for installation,
the CARD device and _RMV methods are required. Without these,
other OSes does not show the eMMC as a valid installation target.
TEST= boot CNL-RVP with Tiano payload and install Windows 10
to the internal eMMC drive.
Change-Id: Icfdccd88bc113d97c2fabf4c63d8d772737a6057
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In ramstage the device_operations are needed for the i2c designware
host controller. Move the intel/common/block/i2c implementation
into the generic driver so other platforms can take advantage of it.
BUG=b:72121803
Change-Id: Id249933fadcc016bfba00e7a6d65f56dfc220724
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
If one wants to implement both i2c_bus.h and i2c_simple.h APIs
the compilation unit needs to be guarded or coordinated carefully
with different compilation units. Instead, name the i2c_bus
functions with _dev such that it indicates that they operate on
struct device. One other change to allow i2c_bus.h to be built in
non-ramstage environments is to ensure DEVTREE_CONST is used for
the dev field in struct bus.
BUG=b:72121803
Change-Id: I267e27e62c95013e8ff8b0728dbe9e7b523de453
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds AC and DC loadline settings since vr_config_enable is
set. Without correct AD/DC loadline settings, VRs reported incorrect
VID values which caused CPU freqency clipping. The clipping reason
could be retrieved from MSR 0x64F. From VRTT report, the AC/DC
loadline resistances are within spec, we can use default value defined
in Table 6-1, doc #543977.
BUG=b:70646304
BRANCH=None
TEST=emerge-fizz coreboot chromeos-bootimage & Read AC/DC loadline
settings from DCI to ensure the values were programmed correctly.
Change-Id: Id0ce29fa5726ca3711aa4c822fb123e2de7bc48f
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23349
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Audio DMIC_DATA needs to be ON in S0ix to support Wake on Voice.
By doing this, SoC can see the DMIC DATA and use for WoV processing.
Thus configuring GPIO_173 as IGNORE IOSSTATE.
TEST=put DUT in S0ix, verify DUT wakes up
Change-Id: I8bf403564e927deb8fed7f415e334bb230107cb0
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/23246
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tune I2C params for I2C bus 5 to ensure that the frequency does not
exceed 400KHz.
BUG=b:65058277
BRANCH=None
TEST=Measured bus frequency for audio <= 400MHz
Change-Id: I18bca023a6a0fe21e6f46f8688264d3c04d77f25
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0, S3, S5 and S0ix
Change-Id: If56d1de5d1157c8cf9c418e3a9d2396ffcfcb0fd
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21610
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[] with data
from agesa_board_gpios[], wrap format and delete agesa_board_gpios[].
Finally, make platform_FchParams_reset() an empty function.
BUG=b:64140392
TEST=Build gardenia.
Change-Id: Id2ea63656a7d2f20f55fc5a4c75457db85b80cbd
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[]
with data from agesa_board_gpios[], wrap format and delete
agesa_board_gpios[] and get_gpio_table(). Then remove the
get_gpio_table() call from BiosCallOuts.c. Finally, remove
get_gpio_table() from
google/kahlee/variants/baseboard/include/baseboard/variants.h.
BUG=b:64140392
TEST=Build grunt. Build and boot kahlee, recording serial output. Search
for "stage bootblock" and "stage ramstage", indicating GPIO being
programmed.
Change-Id: I88bf2c855105a6bc458aedfc6da7725662695667
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add new function sb_program_gpio to be called after AGESA init_reset
and some point within ramstage. For AGESA init_reset, change
amd/stoneyridge/bootblock/bootblock.c function bootblock_soc_init
(add the function after the call to AGESA function).
BUG=b:64140392
TEST=Build kahlee, grunt, gardenia.
Change-Id: I38da26cd1e20617958a6b17d55b7d7c08b8a0230
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22987
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create a GPIO programming function that can be called from multiple
stages (bootblock, romstage and ramstage) that will program only the
GPIO specific to the particular stage.
Add dummy table to kahlee, grunt and gardenia to be able to test a build.
BUG=b:64140392
TEST=Build kahlee, grunt and gardenia with GPIO programming call at
bootblock. This call is removed before commit, so bootblock.c is not
committed.
Change-Id: I88d65c78a186bed9739bc208d5711a31aa3c3bb6
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Change e1a75d4(soc/intel/skylake: Override KBL IccMax settings)
provides correct iccmax settings for kbl-u based on the SKU. Thus,
there is no need to override these values in devicetree. This change
gets rid of iccmax settings in the nami devicetree.
Change-Id: Ie7220bae71fcc597fc20c5e98793d4ea7af5650e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
PC10 is a necessary condition for S0ix entry. With the current C-state limits,
CPU fails to enter PC10 during S0ix. C-state Latency control limits
have to be tuned to new values for PC10 entry.
Change-Id: I0f5227f9c3c10c5a9e335ab118eb0ec185445374
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/23220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Most affected boards set the function disabled (FD) register to an
arbitrary state dumped from systems running the vendor BIOS. This
makes it impossible to enable the devices in devicetree and a pretty
big mess of course because nobody cared to keep the register in sync
with the devicetree.
To get completely rid of most of the writes to FD, move setting of
PCH_DISABLE_ALWAYS into the southbridge code where it belongs.
Change-Id: Ia2a507cbcdf218d09738e2e16f0d3ad1dcf57b8b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/23255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hal Martin <hal.martin+coreboot@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch adds a member device_index to r8168 chip information which
allows driver to identify which NIC card requests MAC address.
In this implementation, only 10 NIC cards are supported, the device
index is in the range of 0 to 10. Regarding to MAC address mapping,
when there is only one NIC on DUT, it is treated as a special case
mapping to "ethernet_mac" in VPD for backward compatibility. When
there are multiple NICs on DUT, they are mapping to "ethernet_macN"
where N is [0-9].
Device tree configuration:
For single NIC: .device_index = "0", maps to "ethernet_mac"
For multiple NICs: .device_index = "[1-10]", maps to
"ethernet_mac[device_index - 1]"
BUG=b:69950854
BRANCH=None
TEST=Added device_index = [0-10] under /drivers/net in device tree &&
Programmed the mac address to VPD in shell
vpd -s ethernet_mac=<mac address> or
vpd -s ethernet-mac[0-9]=<mac address> && reboot the system.
Ensure the MAC address was fetched correctly by ifconfig command.
Change-Id: I108b9bfba39370c8906a2fa4d2b39b106e884e0c
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
this enables the MRC recovery cache for zoombini & variants.
the Kconfig options are:
HAS_RECOVERY_MRC_CACHE
MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN
one note of caution: early board builds will likely fail to boot with:
tlcl_extend: response is 0
tlcl_extend: response is 0
tlcl_lock_nv_write: response is 0
tlcl_lock_nv_write: response is 28b
Failed to lock rec hash space(1f)
Saving nvdata
hard_reset() called!
the fix is to boot into recovery once, then it's business as usual.
using servo, this can be done with:
dut-control power_state:rec
BUG=b:71785303
BRANCH=chromeos-2016.05
TEST=boots on meowth...
Change-Id: I77f36d36a70c8c9c74a7fa3a114d3177f33a708b
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23298
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
this adds missing ACPI entries for the EC, CPU, and power button.
also, the EC to AP wakeup pin assignment is fixed.
BUG=b:71819257
BRANCH=chromeos-2016.05
TEST=booted on meowth. /sys/class/power_supply now gets populated.
Change-Id: I0d091bdf25f9a806bd36329d1f17ac34b3115e48
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/23237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
CONFIG_STONEYRIDGE_SATA_MODE is compared against "magical numbers".
Because actual literals are in AGESA.h and adding agesa_headers.h to
southbridge.h causes compile errors, move comparison code from southbridge.h
to southbridge.c (where they are actually used). Replace these numbers
with actual literals.
BUG=b:71754828
TEST=Build kahlee.
Change-Id: I711473bf492d5ceca026ccd112c2c389a23bdbf9
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
At AGESA AmdInitReset, SATA enable and IDE enable (elements of
FCH_RESET_INTERFACE) are programmed twice (before calling AGESA
for AmdInitReset and from said AGESA function call out), using
different functions with different results. The first would result
in TRUE/FALSE, the second set would result in TRUE/TRUE. Use the
functions of the second set within the first set, and remove them
from the second set.
BUG=b:71754828
TEST=Build kahlle without the change, boot and record output. Rebuild
kahlee with the change, boot and record output. Compare both outputs,
the should be no change except in timing.
Change-Id: I326fcc8801542aa7feef286d02abdfe63354cdd0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
