Kukui is using MIPI display panel and needs some identifier to tell
payloads which LCD module is installed, and to select right kernel
device tree. Following Scarlet, the decision is to embed LCD module ID
as part of SKU ID.
The LCM ID is using a different voltage mapping table from the rest.
Considering the complexity in computation of SKU ID, it is better to
move the cache logic from get_index to caller.
Also revise the mapping table since ADC on 8183 only supports 12
levels.
BUG=b:129299873
TEST=make -j; boots on Kukui Rev2 unit.
Change-Id: Ib0c00bc8ce3c71c445c5c4561403ce8ef4dd5844
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32263
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With commit
'4074ce0cc7 (intel/apollolake: Add HDA to disable_dev function)'
FSP is now requested to switch off HDA PCI device if it is disabled in
devicetree. Doing so results in a warm restart. Normally this event
will be stored in CMOS RAM (if the descriptor is configured to do so)
and therefore no further resets are requested by FSP on the next boots
as long as CMOS RAM is kept alive.
The Siemens mainboards based on Apollo Lake do not have a CMOS battery
and therefore the CMOS is not backed up. This leads to reset requests
from FSP after PCI enumeration on every boot. To avoid this reset enable
HDA in devicetree for these mainboards. Though we do not have any usage
of HDA it should not be an issue that the HDA device is now enabled. The
benefit is though that no reset is requested anymore by FSP.
Change-Id: I637c7c01d73350700c6066fee74fecbb5b93b221
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32295
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the power rail discharge times measured on hatch,
update the assertions widths that have to be programmed in SoC.
BUG=b:129328209
TEST=warm/cold reboot and S3 are working fine on hatch.
Change-Id: I3c6dce0a942e6dcd9e55ef5e58a7e9e8d2b0a1e3
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add a common detect_s3_resume function.
Will be used by other southbridge code.
TODO: Merge with soc/intel/common/*/pmclib
Tested on Lenovo T520 (Intel Sandy Bridge) with Change
I283a841575430f2f179997db8d2f08fa3978a0bb applied as well.
Still boots to OS, no errors visible in dmesg and S3 resume is working.
Change-Id: I88023af522afac8164f068b0fbe0eac601aef702
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Restore Goodix devicetree config because of the
missing Goodix config when moving from baseboard
devicetree to board level overridetree. And move
PENH from I2C#2 to I2C#1.
BUG=b:124460799
BRANCH=None
TEST=local build and tested with Goodix touch screen
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic028c5d7b687a069d7f0510897bea91dca58e91f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Cannon Lake and family require that FSP-M component should be
XIP. This change selects FSP_M_XIP so that the right arguments are
passed into cbfstool when adding this component.
BUG=b:130306520
TEST=Verified that hatch boots fine to OS.
Change-Id: Ifd8a829ebdc7681c81ece4540aa38cdcea7b6fac
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This change uses GPIO IRQ instead of IOAPIC for GPP_A0 pad which is
the interrupt line for sx9310. This is required because IRQ# used by
GPP_A0 is allocated for PIRQ which does not allow IRQ# sharing.
Additionally, this change also configures GPP_A6 for GPIO IRQ. GPP_A6
is currently unused in the devicetree.
BUG=b:129794308
TEST=Verified that there are no interrupt storms on GPP_A0.
Change-Id: Ibb510a647391c0d9cb854d23656bb4b1cb7756ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change configures reset config for all pads routed to IOAPIC as
PLTRST. This is required to ensure that the internal logic of the GPIO
gets reset any time the platform enters S3 or powers off and avoids
any interrupt storms on boot-up.
BUG=b:129933011
TEST=Verified that there are no interrupt storms on boot-up from S5.
Change-Id: Ib790280c9f1410fa18746d4d7d2a5027afd7585b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Move Winbond M25PXX command values to spi_winbond.h
file.
The command values will be used for programming SPI
contoller of Intel Braswell, using this include file.
Update winbond.c file with coreboot header.
BUG=N/A
TEST=Facebook FBG-1701 with flashrom
Change-Id: I9c17c4ed7004209bd3c619d47a7474b0b7e17495
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
FSP code will default enable the onboard serial port.
When external serial port is used, this onboard port needs to be
disabled.
Add function mainboard_after_memory_init() function to perform
required actions to re-enabled output to external serial port.
BUG=N/A
TEST=LPC Post card on Intel Cherry Hill
Change-Id: Ibb6c9e4153b3de58791b211c7f4241be3bceae9d
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add the new configuration 'Krane' that will need at least its own EC.
There's currently no difference in coreboot side.
BUG=b:130011505
TEST=make menuconfig; make -j # select board=Krane
BRANCH=None
Change-Id: Ibb2ec42b08f9a51b22c22f3fe99b203f5eb31627
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Element Self Description register (ESD) [23:16] is R/WO, so let
write the ESD.CID when we start ich7_setup_root_complex_topology.
This value is also used to program the R/WO 'Target Component ID'
registers of RPxD and HHD.
Once it is done, no need to rewrite on them as they become RO.
(For more information, please see ICH7 datasheet page 271.)
Tested done on 945G-M4 using printk before and after writing.
Before this change, writing on those registers had no effect:
ESD: 0x0104: 0x00000802
ULD: 0x0110: 0x00000001
ULBA: 0x0118: 0x00000000
RP1D: 0x0120: 0x01000003
RP2D: 0x0130: 0x02000003
RP3D: 0x0140: 0x03000002
RP4D: 0x0150: 0x04000002
HDD: 0x0160: 0x0f000002
RP5D: 0x0170: 0x05000002
RP6D: 0x0180: 0x06000002
Using this patche, those R/WO get the "right" values.
i.e., We can see RCBA32(ULBA) is now equal to (uintptr_t)DEFAULT_DMIBAR.
ESD: 0x0104: 0x00020802
ULD: 0x0110: 0x01010001
ULBA: 0x0118: 0xfed18000
RP1D: 0x0120: 0x01020003
RP2D: 0x0130: 0x02020003
RP3D: 0x0140: 0x03020002
RP4D: 0x0150: 0x04020002
HDD: 0x0160: 0x0f020002
RP5D: 0x0170: 0x05020002
RP6D: 0x0180: 0x06020002
Change-Id: I3f2199d6da22ce9995496c2a81363710edde81f3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30993
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There will be an out of bounds read if the index is equal
to the array size. Fix the checks to exclude this case.
Found-by: Coverity Scan, CID 1347350, 1347351
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I5b4e8febb68dfd244faf597dfe5cdf509af7a2ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This implementation corrects the GPE DWx mapping for GPIO groups.
The assignments is done in GPIO MISCFG register for all GPIO communities.
And configures the which GPIO communities get register as Tier1.
BUG=b:121212459
TEST: Verified the GPIO MISCFG is getting set as per updated map.
Change-Id: I451997367025a6dc9e5931bd649524e935ad6aca
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32175
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
WiFi enable signal was configured and driven as active-high, but the signal is |To start the server in this Emacs process, stop the existing
actually active-low
BUG=b:130196983
BRANCH=none
TEST=Verified WiFi still works after boot, and also after a suspend/resume cycle. Device powers down correctly using "poweroff".
Change-Id: I64a67f73564188ad0548a1a770169ef2bca47453
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32255
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The value of "write protect" GPIO shall be read in depthcharge,
and the flag shall be set there instead.
BUG=b:124141368, b:124192753, chromium:1556855
TEST=Build locally
CQ-DEPEND=CL:1556855
BRANCH=none
Change-Id: I4d24a057b1385244a836a67c565ee6726a894fdc
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The "write protect" GPIO's cached value is never actually
read after entering depthcharge. Ensure the value from
get_write_protect_state() is being transferred accurately,
so that we may read this GPIO value in depthcharge without
resampling.
The cached value of the "recovery" GPIO is read only on certain
boards which have a physical recovery switch. Correct some of
the values sent to boards which presumably never read the
previously incorrect value. Most of these inaccuracies are from
non-inverted values on ACTIVE_LOW GPIOs.
BUG=b:124141368, b:124192753, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ic17a98768703d7098480a9233b752fe5b201bd51
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
For Kukui CR50_IRQ pin, we're going to replace external pull-up with
internal pull-up. This change won't break older boards, so we can just
always do that when setting up GPIOs.
BUG=b:124821269
BRANCH=none
TEST=Waveform looks correct.
Change-Id: Ib1a90dce583a6aa0cec8ac8ba96d1362f50c16a8
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This pin should be set to its alternative function SRCLKENA0 instead of
GPIO, so that SPM (a power management component of MT8183) can control
it.
BUG=b:113367227
BRANCH=none
TEST=1. Boot. Run 'powerinfo' in EC console and see power state in S0.
2. Run 'powerd_dbus_suspend --wakeup_timeout=10', and then
run 'powerinfo' in EC console and see power state in S3.
3. Wait until AP resume.
4. Run 'powerinfo' in EC console and see power state back to S0.
Change-Id: I0a7e34f95381dec17eb6d166d6552c12e021bd9a
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32120
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a fmd file for 16MiB fmap, so that we can support
both 16MiB / 32MiB SPI flash ROM chips.
BUG=b:129464811
TEST=build hatch firmware image with 16MiB fmap and
verify fmap is updated by 'fuility dump_fmap'
Change-Id: Ifc0103c7fd0d99439f40a31d23422401a6dce826
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SMBIOS spec requires type 7 to be present.
Add the type 7 fields and enums for SMBIOS 3.1+ and fill it with the
"Deterministic Cache Parameters" as available on Intel and AMD.
As CPUID only provides partial information on caches, some fields are set to
unknown.
The following fields are supported:
* Cache Level
* Cache Size
* Cache Type
* Cache Ways of Associativity
Tested on Intel Sandy Bridge (Lenovo T520).
All 4 caches are displayed in dmidecode and show the correct information.
Change-Id: I80ed25b8f2c7b425136b2f0c755324a8f5d1636d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
