Preserve existing UI and add the note about pressing Space to go to
the systemd-boot menu for Pop!_OS Recovery.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Make use of the SMFI command interface to forward logs from edk2 to
System76 EC.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Read the coreboot table containing the TPM PPI handoff buffer and
place it in gEfiTcgPhysicalPresenceInfoHob.
coreboot uses the same PPI interface as QEMU does and installs the
corresponding ACPI code to provide a full PPI interface to the OS.
The OS must reboot in order to execute the requests.
The corresponding coreboot patch can be found here:
https://review.coreboot.org/c/coreboot/+/45568
In a follow up commit the OvmfPkg PhysicalPresence library will be used
to confirm TPM PPI request. This is necessary as coreboot doesn't have
input drivers or a graphical UI that could be used.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
This adds support for FVB in order to support a platform independent
and non-volatile variable store on UefiPayloadPkg. It is required for
non-volatile variable support, TPM support, Secureboot support and more.
Since commit bc744f5893fc4d53275ed26dd8d968011c6a09c1 coreboot supports
the SMMSTORE v2 feature. It implements a SMI handler that is able to
write, read and erase pages in the boot media (SPI flash).
The communication is done using a fixed communication buffer that is
allocated in CBMEM. The existence of this optional feature is advertised
by a coreboot table.
When the SMMSTORE feature is not available the variable emulation is used
by setting PcdEmuVariableNvModeEnable to TRUE.
Add a library for SMMStore to be used in DXE.
The DXE component provides runtime services and takes care of virtual to
physical mapping the communication buffers between SMM and OS.
Make use of the APRIORI DXE to initialize an empty store on the first boot
and set the PCDs to sane values before the variable driver is loaded.
Tests on Intel(R) Xeon(R) E-2288G CPU @ 3.70G showed that the SMI isn't
triggered with a probability of 1:40 of all cases when called in a tight
loop. The CPU continues running and the SMI is triggeres asynchronously
a few clock cycles later. coreboot only handels synchronous APM request
and does nothing on asynchronous APM triggers.
As there's no livesign from SMM it's impossible to tell if the handler
has run. Just wait a bit and try again to trigger a synchronous SMI.
Tests confirmed that out of 5 million tries the SMI is now always handled.
Tested on Linux and Windows 10 on real hardware.
Currently this cannot be tested on coreboot and qemu as it doesn't support
the SMMSTORE on qemu.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
This fixes an issue where the framebuffer provided by coreboot or
slimbootloader will only work on the primary VGA device. If the
framebuffer corresponds to a different device the screen will stay black.
In addition, the code doesn't work for multiple graphic cards, has
reference to non existing functions, and is a duplication of common code.
Call EfiBootManagerConnectVideoController on every display device found,
not only the legacy VGA device. This is the same as OvmfPkg does.
Allows to display output on the framebuffer set up by firmware, which might
not be the VGA device.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Uses the RDRAND instruction if available and install EfiRngProtocol.
The protocol may be used by iPXE or the Linux kernel to gather entropy.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
This is a shoehorned-in implementation of an ACPI BGRT
table, ported pretty much directly from the version used
under CorebootPayloadPkg.
EDK2 provides a facility to do this already, but it assumes
the ACPI tables already exist as EFI structures, so would need
to write code to populate those using the tables already in RAM
created by coreboot. This seemed like the easier option ATM.
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
V1: Add quotes when using $(ARCH) in .dsc and .fdf file.
The quotes are added due to the way by which Core ci parse the .dsc file.
Add UINTN in Hob.c to fix cast from pointer to integer of different size error.
V2: Delete lines which reference ShellBinPkg.The pkg doesn't exist in edk2.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Maurice Ma <maurice.ma@intel.com>
Cc: Benjamin You <benjamin.you@intel.com>
Signed-off-by: DunTan <dun.tan@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Change-Id: I18c2027f57a4fbf291925a11226ed620b808a970
Define some PCDs as DynamicEX PCD to be used as global variable.
Because PcdUartDefaultBaudRate is defined as DynamicEX, remove the code
to set it in platformlib. That code was actually redundant.
Reviewed-by: Guo Dong <guo.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Maurice Ma <maurice.ma@intel.com>
Cc: Benjamin You <benjamin.you@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
For payload entry, use PayloadEntryHobLib as HobLib and payload entry
should initialize hob base.
For DxeCore, use new added DxeHobLib as HobLib, and DxeCore will
initialize hob base.
For Dxe Driver, use new added DxeHobLib as HobLib, and use DxeHobListLib
to initialize hob base.
Adding a new library DxeHobLib + DxeHobListLib instead of using the
DxeHobLib.inf in MdePkg is because the constructor needed be separated
from DxeHobLib.
If not, when building UefiPayloadPkg, the dependency chain is as below:
DebugLib -> SerialPortLib -> PlatformHookLib -> HobLib -> DebugLib
Each library has a constructor, and this becomes a constructor circle.
To break the circle, separate the constructor from the HobLib as a new
DxeHobListLib, which won't depend on DebugLib.
Cc: Maurice Ma <maurice.ma@intel.com>
Cc: Guo Dong <guo.dong@intel.com>
Cc: Benjamin You <benjamin.you@intel.com>
Reviewed-by: Guo Dong <guo.dong@intel.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Currently, BDS driver will link a PlatformBootManagerLib, which contains
platform specific logic. This patch get the platform specific logic from
a protocol, so that platform logic for Boot manager can be in another
binary.
Cc: Maurice Ma <maurice.ma@intel.com>
Cc: Guo Dong <guo.dong@intel.com>
Cc: Benjamin You <benjamin.you@intel.com>
Reviewed-by: Guo Dong <guo.dong@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Currently the console is connected before EndOfDxe causing OptionsROMs
to be loaded, but their drivers aren't used and thus no GOP is installed.
To make use of 3rdparty OptionROMs connect the console after EndOfDxe.
Tested on Intel CFL board using Nvidia Quadro GPU.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Guo Dong <guo.dong@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3100
It is not necessary to have a PEI phase in the UEFI payload since no
specific PEI task is required. This patch adds a UefiPayloadEntry
driver to get UEFI Payload required information from the bootloaders,
convert them into a HOB list, load DXE core and transfer control to it.
Here is the change details:
1) Removed PEI phase, including Peicore, BlSupportPei, SecCore, etc.
2) Added UefiPayloadEntry driver. this is the only driver before DXE core.
3) Added Pure X64 support, dropped Pure IA32 (Could add later if required)
64bit payload with 32bit entry point is still supported.
4) Use one DSC file UefiPayloadPkg.dsc to support X64 and IA32X64 build.
Removed UefiPayloadIa32.dsc and UefiPayloadIa32X64.dsc
Tested with SBL and coreboot on QEMU.
Signed-off-by: Guo Dong <guo.dong@intel.com>
Reviewed-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Benjamin You <benjamin.you@intel.com>
Today's UefiPayloadPkg always uses 0xE0000000 as the PCIE base address
and ignores the value set in AcpiBoardInfo HOB created by the boot
loader. This makes the payload binary cannot work in environment
where the PCIE base address set by boot loader doesn't equal to
0xE0000000.
The patch enhances UefiPayloadPkg so that the PCIE base address
set by boot loader in the AcpiBoardInfo HOB is used.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Guo Dong <guo.dong@intel.com>
Cc: Benjamin You <benjamin.you@intel.com>
EnterS3WithImmediateWake () no longer has any callers, so remove it
from ResetSystemLib.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Guo Dong <guo.dong@intel.com>
Add PS2 keyboard support.
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2316
This patch adds PS2 keyboard support in boot manager, and
add a build flag PS2_KEYBOARD_ENABLE for PS2 keyboard to
build PS2 keyboard driver and SIO driver. Be default the
build flag is not enabled since PS2 keyboard is not common
used. could use -DPS2_KEYBOARD_ENABLE to enable build it
if need this feature.
Signed-off-by: Guo Dong <guo.dong@intel.com>
Reviewed-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Benjamin You <benjamin.you@intel.com>
CorebootModulePkg and CorebootPayloadPkg originally supports coreboot only.
In order to support other bootloaders, such as Slim Bootloader, they need
be updated to be more generic.
UEFI Payload (UefiPayloadPkg) a converged package from CorebootModulePkg
and CorebootPayloadPkg with following updates:
a. Support both coreboot and Slim Bootloader
b. Removed SataControllerDxe and BaseSerialPortLib16550 to use EDK2 modules
c. Support passing bootloader parameter to UEFI payload, e.g. coreboot
table from coreboot or HOB list from Slim Bootloader
d. Using GraphicsOutputDxe from EDK2 with minor change instead of FbGop
e. Remove the dependency to IntelFrameworkPkg and IntelFrameworkModulePkg
and QuarkSocPkg
f. Use BaseDebugLibSerialPort library as DebugLib
g. Use HPET timer, drop legacy 8254 timer support
h. Use BaseXApicX2ApicLib instead of BaseXApicLib
i. Remove HOB gUefiFrameBufferInfoGuid to use EDK2 graphics HOBs.
j. Other clean ups
On how UefiPayloadPkg could work with coreboot/Slim Bootloader, please
refer UefiPayloadPkg/BuildAndIntegrationInstructions.txt
Once UefiPayloadPkg is checked-in, CorebootModulePkg and CorebootPayloadPkg
could be retired.
Signed-off-by: Guo Dong <guo.dong@intel.com>
Reviewed-by: Maurice Ma <maurice.ma@intel.com>
