REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2556
This patch uses CPUID signature check to skip reading the PlatformId MSR,
which is not implemented on AMD processors.
The PlatformId is used for loading microcode patches, which is also not
supported and AMD-based platforms. To mitigate the PlatformId dependency,
PcdCpuMicrocodePatchAddress and PcdCpuMicrodePatchRegionSize must be set
to 0 (default value), in order to bypass microcode loading code paths.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Leo Duran <leo.duran@amd.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2563
This patch is to fix a incremental build regression bug
which happen when using nmake. That's introduced by 818283de3f.
If there is white space before !INCLUDE instruction, nmake will not
process it. Source code's dependent header files are listed in
${deps_file} file, if it's not included successfully, nmake will
not detect the change of those header file.
This patch has been verified in Windows with VS2015 and Linux with GCC5.
The header file add/modify/delete can trig the incremental build with this fix.
There is no impact on the clean build.
Cc: Andrew Fish <afish@apple.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Leif Lindholm <leif@nuviainc.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Bob Feng <bob.c.feng@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Tested-by: Liming Gao <liming.gao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2534
Extend validation of ACPI structure lengths which are read from the
ACPI table being parsed. Additionally check if the structure 'Length'
field value is positive. If not, stop parsing the faulting table.
Some ACPI tables define internal structures of variable size. The
'Length' field inside the substructure is used to update a pointer used
for table traversal. If the byte-length of the structure is equal to 0,
acpiview can enter an infinite loop. This condition can occur if, for
example, the zero-allocated ACPI table buffer is not fully populated.
This is typically a bug on the ACPI table writer side.
In short, this method helps acpiview recover gracefully from a
zero-valued ACPI structure length.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Reviewed-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1608
To avoid false-negative issue in check hash against dbx, both error
condition (as return value) and check result (as out parameter) of
IsSignatureFoundInDatabase() are added. So the caller of this function
will know exactly if a failure is caused by a black list hit or
other error happening, and enforce a more secure operation to prevent
secure boot from being bypassed. For a white list check (db), there's
no such necessity.
All intermediate results inside this function will be checked and
returned immediately upon any failure or error, like out-of-resource,
hash calculation error or certificate retrieval failure.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1608
To avoid false-negative issue in check hash against dbx, both error
condition (as return value) and check result (as out parameter) of
IsCertHashFoundInDatabase() are added. So the caller of this function
will know exactly if a failure is caused by a black list hit or
other error happening, and enforce a more secure operation to prevent
secure boot from being bypassed. For a white list check (db), there's
no such necessity.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1608
The dbx fetching code inside the while/for-loop causes code hard to
understand. Since there's no need to get dbx more than once, this patch
simplify the code logic by moving related code to be outside the while-
loop. db fetching code is also refined accordingly to reduce the indent
level of code.
More comments are also added or refined to explain more details.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1608
In timestamp check after the cert is found in db, the original code jumps
to 'Done' if any error happens in fetching dbx variable. At any of the
jump, VerifyStatus equals to TRUE, which means allowed-by-db. This should
not be allowed except to EFI_NOT_FOUND case (meaning dbx doesn't exist),
because it could be used to bypass timestamp check.
This patch add code to change VerifyStatus to FALSE in the case of memory
allocation failure and dbx fetching failure to avoid potential bypass
issue.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1608
Normally two times of calling gRT->GetVariable() are needed to get
the data of a variable: get the variable size by passing zero variable
size, and then allocate enough memory and pass the correct variable size
and buffer.
But in the inner loop in IsAllowedByDb(), the DbxDataSize was not
initialized to zero before calling gRT->GetVariable(). It won't cause
problem if dbx does not exist. But it will give wrong result if dbx
exists and the DbxDataSize happens to be a small enough value. In this
situation, EFI_BUFFER_TOO_SMALL will be returned. Then the result check
code followed will jump to 'Done', which is not correct because it's
actually the value expected.
if (Status == EFI_BUFFER_TOO_SMALL) {
goto Done;
}
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
In case the signers' certificate stack, retrieved from the PE/COFF image's
Authenticode blob, has zero elements (=there are zero signer certificates),
then we should consider the image forbidden by DBX, not accepted by DBX.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Check if the ACPI table length, as reported in the ACPI table header, is
big enough to fit at least the header itself.
If not, report an error to the user and stop parsing the table in order
to prevent buffer overruns.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Reviewed-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
Remove duplicate Generic Address Structure (GAS) and ACPI table header
size definitions. Replace any dependencies with the definitions from
Acpi63.h.
AcpiParser.h redefines the size of Generic Address Structure (GAS) and
the ACPI table header. The motivation is to 'minimise any reference to
the EDK2 ACPI headers in an attempt to provide cross checking'. While
the redefined values are unlikely to change, redefinition causes
unnecessary maintenance overhead for acpiview.
In addition to this, EDK2 ACPI headers are referenced throughout the
entire project, so the assumption should be that the definitions in
these header files are correct.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Reviewed-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
Match data type and format specifier for printing.
1. Type cast ProcessorNumber and FeatureIndex to UINT32
as %d only expects a UINT32.
2. Use %08x instead of %08lx for CacheControl to print Index
as it is UINT32 type.
3. Use %016lx instead of %08lx for MemoryMapped to print
(Index | LShiftU64 (HighIndex, 32)) as it is UINT64 type.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1989
The commit will avoid unmapping the same resource in error handling logic
for function BuildAdmaDescTable() and SdMmcCreateTrb().
For the error handling in BuildAdmaDescTable():
The error is directly related with the corresponding Map() operation
(mapped address beyond 4G, which is not supported in ADMA), so the Unmap()
operation is done in the error handling logic, and then setting
'Trb->AdmaMap' to NULL to avoid double Unmap.
For the error handling in SdMmcCreateTrb():
The error is not directly related with the corresponding Map() operation,
so the commit will update the code to left SdMmcFreeTrb() for the Unmap
operation to avoid double Unmap.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Commit c7c964b and dd01704 add header file for FIT table and update
MpInitLib to support FIT based microcode shadow operation. There are
comments that FIT is Intel specific specification instead of industry
standard, which should not be placed in EDK2 MdePkg and UefiCpuPkg.
This patch removes the header file added by c7c964b.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Siyuan Fu <siyuan.fu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Commit c7c964b and dd01704 add header file for FIT table and update
MpInitLib to support FIT based microcode shadow operation. There are
comments that FIT is Intel specific specification instead of industry
standard, which should not be placed in EDK2 MdePkg and UefiCpuPkg.
So this patch adds a platform PPI for the microcode shadow logic, and
remove the FIT related code from EDK2.
The FIT based microcode shadow support will be implemented as a new
platform PEIM in IntelSiliconPkg in edk2-platforms.
This patch doesn't provide a DXE version shadow microcode protocol,
a platform which only uses DxeMpInitLib instance only supports PCD
based microcode shadowing.
A detailed design doc can be found here:
https://edk2.groups.io/g/devel/files/Designs/2020/0214/Support%20
the%202nd%20Microcode%20FV%20Flash%20Region.pdf
TEST: Tested on FIT enabled platform.
BZ: https://tianocore.acgmultimedia.com/show_bug.cgi?id=2449
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Siyuan Fu <siyuan.fu@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1584
The flow of CPU feature initialization logic is:
1. BSP calls GetConfigDataFunc() for each thread/AP;
2. Each thread/AP calls SupportFunc() to detect its own capability;
3. BSP calls InitializeFunc() for each thread/AP.
There is a design gap in step #3. For a package scope feature that only
requires one thread of each package does the initialization operation,
what InitializeFunc() currently does is to do the initialization
operation only CPU physical location Core# is 0.
But in certain platform, Core#0 might be disabled in hardware level
which results the certain package scope feature isn't initialized at
all.
The patch adds a new field First to indicate the CPU's location in
its parent scope.
First.Package is set for all APs/threads under first package;
First.Core is set for all APs/threads under first core of each
package;
First.Thread is set for the AP/thread of each core.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1366
Commit b3c71b472d supported MSR setting
in different scopes. It added below macro:
CPU_FEATURE_THREAD_BEFORE
CPU_FEATURE_THREAD_AFTER
CPU_FEATURE_CORE_BEFORE
CPU_FEATURE_CORE_AFTER
CPU_FEATURE_PACKAGE_BEFORE
CPU_FEATURE_PACKAGE_AFTER
And it re-interpreted CPU_FEATURE_BEFORE as CPU_FEATURE_THREAD_BEFORE
and CPU_FEATURE_AFTER as CPU_FEATURE_THREAD_AFTER.
This patch retires CPU_FEATURE_BEFORE and CPU_FEATURE_AFTER
completely.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
The Platform Communications Channel Table (PCCT) was defined in:
ACPI Specification Version 5.0, Errata A - Published Nov. 13, 2013.
Starting from the Acpi50.h header file, there are definitions
describing the table but a macro with the table's signature is missing.
This patch adds the definition of Platform Communications Channel
Table's signature to the relevant ACPI header files.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Sami Mujawar <sami.mujawar@arm.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=2525
SafeUint64Mult() looks for 64-bit overflows and performs
several 32-bit multiples with 64-bit results to check for
all possible overflow conditions. IA32 builds using VS20xx
with optimizations enabled are producing a reference to
the _allmull intrinsic.
The fix is to use MultU64x64() instead of '*' for
these operations. These are safe because the inputs
are guaranteed to have the upper 32-bits clear, which
means MultU64x64() can never overflow with those inputs.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Bret Barkelew <Bret.Barkelew@microsoft.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Bret Barkelew <bret.barkelew@microsoft.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=2142
gAdvancedFeaturePkgTokenSpaceGuid.PcdSmbiosType0BiosInformation|
{0x0}|SMBIOS_TABLE_TYPE0|0x80010000 {
<HeaderFiles>
IndustryStandard/SmBios.h
<Packages>
MdePkg/MdePkg.dec
AdvancedFeaturePkg/AdvancedFeaturePkg.dec
}
If there's a PcdStructHF or PcdStructPKGs in StructPcd,
EccTool report error,IndexError: list index out of range
This patch is going to fix this issue
Cc: Liming Gao <liming.gao@intel.com>
Cc: Bob Feng <bob.c.feng@intel.com>
Signed-off-by: Zhiju.Fan <zhijux.fan@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
NASM_INC contains the list of directory to include when using
the nasm assembler.
In nmake makefiles, a trailing backslash escapes the newline char
and replaces it with a space ' '. To have a literal trailing
backslash, it must be escaped with a caret '^'. This is not
necessary for GNU makefiles.
On windows platforms, for the NASM_INC macro, a caret escaping
a trailing a backslash was appended to the last included
folder regardless of the makefile type.
For instance, "/Include/" was replaced by "/Include/^\".
This is causing a build failure on windows platforms using
GNU makefiles since the caret '^' doesn't escape any chars in
GNU makefiles and is thus conserved.
"/Include^\" was replaced by "/Include\/" in nmake makefiles,
but remained "/Include/^\" in GNU makefiles.
This patch removes the caret '^' on the build using GNU makefiles.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
The GenMake.py script tests the platform environment
to determine the type of makefile that needs to be
generated. If a Windows build host is detected, the
makefile generated is of Nmake type. Otherwise a
GNUmake type is generated.
Furthermore, the <TARGET>_<TAGNAME>_<ARCH>_MAKE_PATH
option in tools_def.template defines the make tool
to use.
E.g.: for VS2017 this is configured to use Nmake, cf.
*_VS2017_*_MAKE_PATH = DEF(VS2017_BIN_HOST)\nmake.exe
while for GCC5 it is setup to use GNU make.
*_GCC5_*_MAKE_PATH = DEF(GCC_HOST_PREFIX)make
This prevents using the GCC compiler toolchain on a
Windows build host.
To address this issue this patch introduces 2 factors
to determine the generated makefile output.
1. Platform -> to determine shell commands used
in makefile.
2. MakeTool -> to determine the type of makefile
that needs to be generated.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
The header includes Physical Layer PCI Express Extended Capability
definitions based on section 7.7.6 of PCI Express Base Specification 5.0.
Signed-off-by: Felix Polyudov <felixp@ami.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2465
Commit 89164babec:
UefiCpuPkg/MpInitLib: don't shadow the microcode patch twice.
attempted to use 'MicrocodePatchRegionSize' and 'MicrocodePatchAddress'
fields to avoid loading the microcode patches data into memory again in
the DXE phase.
However, the CPU_MP_DATA structure has members with type 'UINTN' or
pointer before the microcode patch related fields. This may cause issues
when PEI and DXE are of different archs (e.g. PEI - IA32, DXE - x64),
since the microcode patch related fields will have different offsets in
the CPU_MP_DATA structure.
Commit 88bd066166:
UefiCpuPkg/MpInitLib: Relocate microcode patch fields in CPU_MP_DATA
tried to resolve the above-mentioned issue by relocating the fields
'MicrocodePatchRegionSize' and 'MicrocodePatchAddress' before members with
different size between different archs. But it failed to take the case of
pre-built binaries (e.g. FSP) into consideration.
Binaries can be built when the code base had a different version of the
CPU_MP_DATA structure definition. This may cause issues when accessing
these microcode patch related fields, since their offsets are different
(between PEI phase in the binaries and DXE phase in current code
implementation).
This commit will use the newly introduced EDKII microcode patch HOB
instead for the DXE phase to get the information of the loaded microcode
patches data done in the PEI phase. And the 'MicrocodePatchRegionSize' and
'MicrocodePatchAddress' fields in CPU_MP_DATA will not be used to pass
information between phases.
For pre-built binaries, they can be classified into 3 types with regard to
the time when they are being built:
A. Before commit 89164babec
(In other words, 'MicrocodePatchRegionSize' and 'MicrocodePatchAddress'
were not being used to skip microcode load in DXE)
For this case, the EDKII microcode patch HOB will not be produced. This
commit will load the microcode patches data again in DXE. Such behavior is
the same with the code base back then.
B. After commit 89164babec, before commit e1ed55738e
(In other words, 'MicrocodePatchRegionSize' and 'MicrocodePatchAddress'
being used to skip microcode load in DXE, but failed to work properly
between differnt archs.)
For this case, the EDKII microcode patch HOB will not be produced as well.
This commit will also load the microcode patches data again in DXE.
But since commit 89164babec failed to keep the detection and application
of microcode patches working properly in DXE after skipping the load, we
fall back to the origin behavior (that is to load the microcode patches
data again in DXE).
C. After commit e1ed55738e
(In other words, EDKII microcode patch HOB will be produced.)
For this case, it will have the same behavior with the BIOS built from
the current source codes.
Cc: Michael Kubacki <michael.a.kubacki@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
This reverts commit 88bd066166.
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2465
Commit 88bd066166 relocates the 'MicrocodePatchAddress' and
'MicrocodePatchRegionSize' fields in structure CPU_MP_DATA to ensure that
they can be properly passed between different architectures.
However, such change is not backward compatible with the scenario like
pre-existing binaries such as FSP. These binaries are built when the code
base has a different version of the CPU_MP_DATA structure definition. This
may cause issues when accessing the 'MicrocodePatchAddress' and
'MicrocodePatchRegionSize' fields, since their offsets are different
(between PEI phase in the FSP binaries and DXE phase in current code
implementation).
Cc: Michael Kubacki <michael.a.kubacki@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Check if global (in the scope of the DBG2 parser) pointers have been
successfully updated before they are used for further table parsing.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Check if global (in the scope of the GTDT parser) pointers have been
successfully updated before they are used for further table parsing.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Check if global (in the scope of the IORT parser) pointers have been
successfully updated before they are used for further table parsing.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Check if the NumberOfPrivateResources, ProcessorTopologyStructureType
and ProcessorTopologyStructureLength pointers have been successfully
updated before they are used for further table parsing.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Check if the MadtInterruptControllerType and
MadtInterruptControllerLength pointers have been successfully updated
before they are used for further table parsing.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Check if SratRAType and SratRALength pointers have been successfully
updated before they are used for further table parsing.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
1. Check if the 'Number of System Localities' provided can be
represented in the SLIT table. The table 'Length' field is a 32-bit
value while the 'Number of System Localities' field is 64-bit long.
2. Check if the SLIT matrix fits in the table buffer. If N is the SLIT
locality count, then the matrix used to represent the localities is
N*N bytes long. The ACPI table length must be big enough to fit the
matrix.
3. Remove (now) redundant 64x64 bit multiplication.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Check if SlitSystemLocalityCount pointer has been successfully updated
before it is used for further table parsing.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Check if global pointers have been successfully updated before they
are used for further table parsing.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
Check if XsdtAddress pointer has been successfully updated before it
is used for further table parsing.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
For fields outside the buffer length provided, reset any pointers,
which were supposed to be updated by a ParseAcpi() function call to
NULL. This way one can easily validate if a pointer was successfully
updated.
The ParseAcpi() function parses the given ACPI table buffer by a
number of bytes which is a minimum of the buffer length and the length
described by ACPI_PARSER array. If the buffer length is shorter than
the array describing how to process the ACPI structure, then it is
possible that the ItemPtr inside ACPI_PARSER may not get updated or
initialized. This can lead to an error if the value pointed to by
ItemPtr is later used to control the parsing logic.
A typical example would be a 'number of elements' field in an ACPI
structure header which defines how many substructures of a given type
are present in the structure body. If the 'number of elements' field
is not parsed, we will have a dangling pointer which could cause a
problem later.
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
ShellParametersProtocol::UpdateArgcArgv() can return
a EFI_INVALID_PARAMETER value. Document it.
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
ShellParametersProtocol::ParseCommandLineToArgs() can return
a EFI_INVALID_PARAMETER value. Document it.
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
FADT parser was checking for reduced ACPI flag incorrectly
leading to incorrect error message if FIRMWARE_CTRL and
X_FIRMWARE_CTRL are both 0.
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Fix various typos in comments and documentation.
When "VbeShim.asm" is modified, we have to re-run "VbeShim.sh"
to update "VbeShim.h".
The string modified by this patch is only used when the DEBUG
macro (at the top of the file) is commented out. Since the
string is not referenced, NASM eliminates it, resulting in
the same byte array content in "VbeShim.h".
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Antoine Coeur <coeur@gmx.fr>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20200207010831.9046-58-philmd@redhat.com>
The DxeTpmMeasureBootHandler and DxeTpm2MeasureBootHandler handlers
are SECURITY2_FILE_AUTHENTICATION_HANDLER prototype. This prototype
can not return EFI_INVALID_PARAMETER.
The prototype documentation states it returns EFI_ACCESS_DENIED if:
"The file specified by File and FileBuffer did not authenticate,
and the platform policy dictates that the DXE Foundation may not
use File."
Correct the documentation, and add a early check, returning
EFI_ACCESS_DENIED when File is NULL.
Noticed while reviewing commit 6d57592740.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Increase length of path that can be read from system from 200 to 400 to
allow for longer build paths.
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
https://bugzilla.tianocore.org/show_bug.cgi?id=2505
* DSC in root of package file to perform a package
build of the UnitTestFrameworkPkg and build sample
unit test for all supported target environments.
* DSC file in Test directory to build the sample
unit test for the host environment.
* UnitTestFrameworkPkgTarget.dsc.inc - DSC include
file to !include when building unit tests for
target environments.
* UnitTestFrameworkPkgHost.dsc.inc - DSC include
file to !include when building unit tests for
target environments.
* YAML file with set of CI checks to perform on UnitTestFrameworkPkg.
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Bret Barkelew <Bret.Barkelew@microsoft.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Bret Barkelew <Bret.Barkelew@microsoft.com>
Reviewed-by: Sean Brogan <sean.brogan@microsoft.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=2505
Add the following library instances that are used to
build unit tests for host and target environments.
* CmockaLib with cmocka submodule to:
https://git.cryptomilk.org/projects/cmocka.git
* DebugLibPosix - Instance of DebugLib based on POSIX
APIs (e.g. printf).
* MemoryAllocationLibPosix - Instance of MemoryAllocationLib
based on POSIX APIs (e.g. malloc/free).
* UnitTestBootLibNull - Null instance of the UnitTestBootLib
* UnitTestBootLibUsbClass - UnitTestBootLib instances that
supports setting boot next to a USB device.
* UnitTestLib - UnitTestLib instance that is designed to work
with PEI, DXE, SMM, and UEFI Shell target environments.
* UnitTestLibCmocka - UintTestLib instance that uses cmocka
APIs and can only be use in a host environment.
* UnitTestPersistenceLibNull - Null instance of the
UnitTestPersistenceLib
* UnitTestPersistenceLibSimpleFileSystem - UnitTestPersistenceLib
instance that can safe the unit test framework state to a
media device that supports the UEFI Simple File System
Protocol.
* UnitTestResultReportLibConOut - UnitTestResultReportLib
instance that sends report results to the UEFI standard
output console.
* UnitTestResultReportLibDebugLib - UnitTestResultReportLib
instance that sends report results to a DebugLib using
DEBUG() macros.
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Bret Barkelew <Bret.Barkelew@microsoft.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Bret Barkelew <Bret.Barkelew@microsoft.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=2505
Add public interfaces for use by unit test implementations.
* Include path to cmocka library interfaces.
* PcdUnitTestLogLevel to set the unit test logging message
level to filter log messages.
Add private interfaces that are used by UnitTestLib
implementations.
* [Private] UnitTestBootLib - Set boot next to continue unit
tests across a reboot.
* [Private] UnitTestPersistenceLib - Save unit test framework
state to a persistent storage device.
* [Private] UnitTestResultLib - Output unit test results to a
console device.
* [Private] UnitTestFrameworkTypes.h - Internal structures
used by UnitTestLib implementations to keep track if unit
test frameworks, unit test suites, and unit tests along with
the serialized storage format to save a unit test framework
state to persistent storage.
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Bret Barkelew <Bret.Barkelew@microsoft.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Bret Barkelew <Bret.Barkelew@microsoft.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=2505
Add UnitTestLib class to MdePkg that provides services
and macros to implement unit tests. These services and
macros support the following features:
* Create a Unit Test Framework
* Add a Unit Test Suite to a Unit Test Framework
+ Support optional step that executes before a Unit
Test Suite is started.
+ Support optional step that executes after a Unit
Test Suite is finished.
* Add a Unit Test to a Unit Test Suite
+ Support optional step that executes before a Unit
Test is started.
+ Support optional step that executes after a Unit
Test is finished.
* Run all unit tests added to a Unit Test Framework
* Save Unit Test Framework state to persistent storage
* Support assertion checks in a unit test for TRUE, FALSE,
EQUAL, MEM_EQUAL, NOT_EFI_ERROR, STATUS_EQUAL, and NOT_NULL.
* Support generation of log messages at ERROR, WARN, INFO,
and VERBOSE levels.
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Bret Barkelew <Bret.Barkelew@microsoft.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Bret Barkelew <Bret.Barkelew@microsoft.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=2420
Based on the following package with changes to merge into
CryptoPkg.
https://github.com/microsoft/mu_plus/tree/dev/201908/SharedCryptoPkg
Add Crypto library instances and modules that consume/produce
the EDK II Crypto Protocols/PPIs to the CryptoPkg DSC file.
The default build of CryptoPkg performs a package verification
build.
The CRYPTO_SERVICES define is added that supports the following
settings.
* PACKAGE - Package verification build of all components. Null
versions of libraries are used to minimize build times.
* ALL - Build PEIM, DXE, and SMM drivers. Protocols and PPIs
publish all services.
* NONE - Build PEIM, DXE, and SMM drivers. Protocols and PPIs
publish no services. Used to verify compiler/linker
optimizations are working correctly.
* MIN_PEI - Build PEIM with PPI that publishes minimum required
services.
* MIN_DXE_MIN_SMM - Build DXE and SMM drivers with Protocols that publish
minimum required services.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Xiaoyu Lu <xiaoyux.lu@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=2420
Based on the following package with changes to merge into
CryptoPkg.
https://github.com/microsoft/mu_plus/tree/dev/201908/SharedCryptoPkg
Add the CryptoPei, CryptoDxe, and CryptoSmm modules that produce
EDK II Crypto Protocols/PPIs that provide the same services as
the BaseCryptLib class.
In order to optimize the size of CryptoPei, CryptoDxe, and
CryptoSmm modules for a specific platform, the FixedAtBuild
PCD gEfiCryptoPkgTokenSpaceGuid.PcdCryptoServiceFamilyEnable
is used to determine if a specific service is enabled or
disabled. If a service is enabled, then a call is made to
the BaseCryptLib service. If the service is disabled, then
a DEBUG() message and ASSERT() are performed and a default
return value is returned. This provides simple detection
of a service that is disabled but is used by another module
when DEBUG()/ASSERT() macros are enabled.
The use of a FixedAtBuild PCD is required so the compiler
and linker know each services enable/disable setting at
build time and allows disabled services to be optimized away.
CryptoPei supports both pre-mem and post-mem use cases.
If CryptoPei is initially dispatched pre-mmem, the the
register for shadow service is used so the Crypto PPI can
be reinstalled post-mem.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Xiaoyu Lu <xiaoyux.lu@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=2420
Based on the following package with changes to merge into
CryptoPkg.
https://github.com/microsoft/mu_plus/tree/dev/201908/SharedCryptoPkg
Add the EDK II Crypto Protocol, EDK II SMM Crypto Protocol
and EDK II Crypto PPI that provide the same services as the
BaseCryptLib. One additional GetVersion() services is provided
to support backward compatible extensions to these new
Protocols/PPIs if new services are added to BaseCryptLib in the
future. The EDK II Crypto Protocols/PPIs are located in a
private directory so they are only available CryptoPkg components.
In order to optimize the size of modules that produce the
EDK II Crypto Protocols/PPIs define a FixedAtBuild PCD
gEfiCryptoPkgTokenSpaceGuid.PcdCryptoServiceFamilyEnable.
This PCD is type VOID* and is associated with the structure
PCD_CRYPTO_SERVICE_FAMILY_ENABLE. This structure contains
bitfields and unions that allow a platform DSC files to
enable/disable entire families of services or enable/disable
individual services in the produced EDK II Crypto
Protocols/PPIs.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Xiaoyu Lu <xiaoyux.lu@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2001
For S3BootScriptLib APIs:
S3BootScriptSaveIoWrite
S3BootScriptSaveMemWrite
S3BootScriptSavePciCfgWrite
S3BootScriptSavePciCfg2Write
S3BootScriptSaveSmbusExecute
S3BootScriptSaveInformation
S3BootScriptSaveInformationAsciiString
S3BootScriptLabel (happen in S3BootScriptLabelInternal())
possible numeric truncations will happen that may lead to S3 boot script
entry with improper size being returned to store the boot script data.
This commit will add checks to prevent this kind of issue.
Please note that the remaining S3BootScriptLib APIs:
S3BootScriptSaveIoReadWrite
S3BootScriptSaveMemReadWrite
S3BootScriptSavePciCfgReadWrite
S3BootScriptSavePciCfg2ReadWrite
S3BootScriptSaveStall
S3BootScriptSaveDispatch2
S3BootScriptSaveDispatch
S3BootScriptSaveMemPoll
S3BootScriptSaveIoPoll
S3BootScriptSavePciPoll
S3BootScriptSavePci2Poll
S3BootScriptCloseTable
S3BootScriptExecute
S3BootScriptMoveLastOpcode
S3BootScriptCompare
are not affected by such numeric truncation.
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Jian J Wang <jian.j.wang@intel.com>
Current UpdateCapsule service will reject all non-reset capsule images and
return EFI_OUT_OF_RESOURCE if the system is at runtime. This will block a
platform CapsuleLib from implementing ProcessCapsuleImage() with runtime
capsule processing capability.
This patch removes this restriction. The change is controled by a feature
PCD PcdSupportProcessCapsuleAtRuntime, and the default value is FALSE
which means not enable this feature.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=2501
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Signed-off-by: Siyuan Fu <siyuan.fu@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=2496
Reduce the build and env dependencies for the Structured PCD
application by removing the dependency on Common.lib that
is only built when BaseTools is built which does not
happen if pre-compiled BaseToools are used. Change the
makefile for the Structure PCD application to build all
files from sources which adds PcdValueCommon.c to the
makefile. Also remove PcdValueCommon.c from Common.lib.
With the change to the makefile for the Structured PCD
application, multiple C files are compiled. Only
PcdValueInit.c contains the extra information expected
by the error/warning message parser. Only parse the
DSC line number into an error message if there is an
error/warning in PcdValueInit.c. Errors/warnings in
other files should be passed through. This fixes a build
failure with no useful log information that was observed
when there was a compiler error in PcdValueCommon.c.
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Bob Feng <bob.c.feng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
Before writing data to FIFO, wait for the serial port to be ready,
to make sure both the transmit FIFO and shift register empty. Code
comment was saying the right thing but code was missing a check.
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
The "-tc" option of the iasl compiler allows to generate a
.hex file containing a C array storing AML bytecode.
An online discussion suggested that this "-tc" option
was specific to the iasl compiler and it shouldn't be relied
on. This conversation is available at:
https://edk2.groups.io/g/devel/topic/39786201#49659
A way to address this issue is to implement a compiler
independent script that takes an AML file as input, and
generates a .hex file.
This patch implements a Python script that converts an AML
file to a .hex file, containing a C array storing AML bytecode.
This scipt has been tested with the AML output from the
following compilers supported by the EDKII implementation:
* Intel ASL compiler
* Microsoft ASL compiler
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
We check the author/committer name/email are properly displayed
since commits 8ffa47fb3ab..c0328cf3803. However if PatchCheck.py
uses the mailmap, it will check sanitized names/emails.
Use the --no-use-mailmap option so PatchCheck.py will check
unsanitized input.
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Cc: Bob Feng <bob.c.feng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2498
Commit fd30b00707 updated the logic in function MicrocodeDetect() that
will directly use the CPUID and PlatformID information from the 'CpuData'
field in the CPU_MP_DATA structure, instead of collecting these
information for each processor via AsmCpuid() and AsmReadMsr64() calls
respectively.
At that moment, this approach worked fine for APs. Since:
a) When the APs are waken up for the 1st time (1st MpInitLibInitialize()
entry at PEI phase), the function InitializeApData() will be called for
each AP and the CPUID and PlatformID information will be collected.
b) During the 2nd entry of MpInitLibInitialize() at DXE phase, when the
APs are waken up again, the function InitializeApData() will not be
called, which means the CPUID and PlatformID information will not be
collected. However, the below logics in MicrocodeDetect() function:
CurrentRevision = GetCurrentMicrocodeSignature ();
IsBspCallIn = (ProcessorNumber == (UINTN)CpuMpData->BspNumber) ? TRUE : FALSE;
if (CurrentRevision != 0 && !IsBspCallIn) {
//
// Skip loading microcode if it has been loaded successfully
//
return;
}
will ensure that the microcode detection and application will be
skipped due to the fact that such process has already been done in the
PEI phase.
But after commit 396e791059, which removes the above skip loading logic,
the CPUID and PlatformID information on APs will be used upon the 2nd
entry of the MpInitLibInitialize(). But since the CPUID and PlatformID
information has not been collected, it will bring issue to the microcode
detection process.
This commit will update the logic in MicrocodeDetect() back to always
collecting the CPUID and PlatformID information explicitly.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Siyuan Fu <siyuan.fu@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Siyuan Fu <siyuan.fu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
During normal boot, when EFI_DXE_SMM_READY_TO_LOCK_PROTOCOL is installed
by platform BDS, the SMM IPL locks SMRAM (TSEG) through
EFI_SMM_ACCESS2_PROTOCOL.Lock(). See SmmIplReadyToLockEventNotify() in
"MdeModulePkg/Core/PiSmmCore/PiSmmIpl.c".
During S3 resume, S3Resume2Pei locks SMRAM (TSEG) through
PEI_SMM_ACCESS_PPI.Lock(), before executing the boot script. See
S3ResumeExecuteBootScript() in
"UefiCpuPkg/Universal/Acpi/S3Resume2Pei/S3Resume.c".
Those are precisely the places where the SMRAM at the default SMBASE
should be locked too. Add such an action to SmramAccessLock().
Notes:
- The SMRAM at the default SMBASE doesn't support the "closed and
unlocked" state (and so it can't be closed without locking it, and it
cannot be opened after closing it).
- The SMRAM at the default SMBASE isn't (and shouldn't) be exposed with
another EFI_SMRAM_DESCRIPTOR in the GetCapabilities() members of
EFI_SMM_ACCESS2_PROTOCOL / PEI_SMM_ACCESS_PPI. That's because the SMRAM
in question is not "general purpose"; it's only QEMU's solution to
protect the initial SMI handler from the OS, when a VCPU is hot-plugged.
Consequently, the state of the SMRAM at the default SMBASE is not
reflected in the "OpenState" / "LockState" fields of the protocol and
PPI.
- An alternative to extending SmramAccessLock() would be to register an
EFI_DXE_SMM_READY_TO_LOCK_PROTOCOL notify in SmmAccess2Dxe (for locking
at normal boot), and an EDKII_S3_SMM_INIT_DONE_GUID PPI notify in
SmmAccessPei (for locking at S3 resume).
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1512
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Message-Id: <20200129214412.2361-10-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
When OVMF runs in a SEV guest, the initial SMM Save State Map is
(1) allocated as EfiBootServicesData type memory in OvmfPkg/PlatformPei,
function AmdSevInitialize(), for preventing unintended information
sharing with the hypervisor;
(2) decrypted in AmdSevDxe;
(3) re-encrypted in OvmfPkg/Library/SmmCpuFeaturesLib, function
SmmCpuFeaturesSmmRelocationComplete(), which is called by
PiSmmCpuDxeSmm right after initial SMBASE relocation;
(4) released to DXE at the same location.
The SMRAM at the default SMBASE is a superset of the initial Save State
Map. The reserved memory allocation in InitializeRamRegions(), from the
previous patch, must override the allocating and freeing in (1) and (4),
respectively. (Note: the decrypting and re-encrypting in (2) and (3) are
unaffected.)
In AmdSevInitialize(), only assert the containment of the initial Save
State Map, in the larger area already allocated by InitializeRamRegions().
In SmmCpuFeaturesSmmRelocationComplete(), preserve the allocation of the
initial Save State Map into OS runtime, as part of the allocation done by
InitializeRamRegions(). Only assert containment.
These changes only affect the normal boot path (the UEFI memory map is
untouched during S3 resume).
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1512
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Message-Id: <20200129214412.2361-9-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The 128KB SMRAM at the default SMBASE will be used for protecting the
initial SMI handler for hot-plugged VCPUs. After platform reset, the SMRAM
in question is open (and looks just like RAM). When BDS signals
EFI_DXE_MM_READY_TO_LOCK_PROTOCOL (and so TSEG is locked down), we're
going to lock the SMRAM at the default SMBASE too.
For this, we have to reserve said SMRAM area as early as possible, from
components in PEI, DXE, and OS runtime.
* QemuInitializeRam() currently produces a single resource descriptor HOB,
for exposing the system RAM available under 1GB. This occurs during both
normal boot and S3 resume identically (the latter only for the sake of
CpuMpPei borrowing low RAM for the AP startup vector).
But, the SMRAM at the default SMBASE falls in the middle of the current
system RAM HOB. Split the HOB, and cover the SMRAM with a reserved
memory HOB in the middle. CpuMpPei (via MpInitLib) skips reserved memory
HOBs.
* InitializeRamRegions() is responsible for producing memory allocation
HOBs, carving out parts of the resource descriptor HOBs produced in
QemuInitializeRam(). Allocate the above-introduced reserved memory
region in full, similarly to how we treat TSEG, so that DXE and the OS
avoid the locked SMRAM (black hole) in this area.
(Note that these allocations only occur on the normal boot path, as they
matter for the UEFI memory map, which cannot be changed during S3
resume.)
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1512
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Message-Id: <20200129214412.2361-8-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The permanent PEI RAM that is published on the normal boot path starts
strictly above MEMFD_BASE_ADDRESS (8 MB -- see the FDF files), regardless
of whether PEI decompression will be necessary on S3 resume due to
SMM_REQUIRE. Therefore the normal boot permanent PEI RAM never overlaps
with the SMRAM at the default SMBASE (192 KB).
The S3 resume permanent PEI RAM is strictly above the normal boot one.
Therefore the no-overlap statement holds true on the S3 resume path as
well.
Assert the no-overlap condition commonly for both boot paths in
PublishPeiMemory().
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1512
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Message-Id: <20200129214412.2361-7-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
In Intel datasheet 316966-002 (the "q35 spec"), Table 5-1 "DRAM Controller
Register Address Map (D0:F0)" leaves the byte register at config space
offset 0x9C unused.
On QEMU's Q35 board, for detecting the "SMRAM at default SMBASE" feature,
firmware is expected to write MCH_DEFAULT_SMBASE_QUERY (0xFF) to offset
MCH_DEFAULT_SMBASE_CTL (0x9C), and read back the register. If the value is
MCH_DEFAULT_SMBASE_IN_RAM (0x01), then the feature is available, and the
range mentioned below is open (accessible to code running outside of SMM).
Then, once firmware writes MCH_DEFAULT_SMBASE_LCK (0x02) to the register,
the MCH_DEFAULT_SMBASE_SIZE (128KB) range at 0x3_0000 (SMM_DEFAULT_SMBASE)
gets closed and locked down, and the register becomes read-only. The area
is reopened, and the register becomes read/write, at platform reset.
Add the above-listed macros to "Q35MchIch9.h".
(There are some other unused offsets in Table 5-1; for example we had
scavenged 0x50 for implementing the extended TSEG feature. 0x9C is the
first byte-wide register standing in isolation after 0x50.)
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1512
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Message-Id: <20200129214412.2361-4-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
For supporting VCPU hotplug with SMM enabled/required, QEMU offers the
(dynamically detectable) feature called "SMRAM at default SMBASE". When
the feature is enabled, the firmware can lock down the 128 KB range
starting at the default SMBASE; that is, the [0x3_0000, 0x4_FFFF]
interval. The goal is to shield the very first SMI handler of the
hotplugged VCPU from OS influence.
Multiple modules in OVMF will have to inter-operate for locking down this
range. Introduce a dynamic PCD that will reflect the feature (to be
negotiated by PlatformPei), for coordination between drivers.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1512
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Message-Id: <20200129214412.2361-2-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
https://bugzilla.tianocore.org/show_bug.cgi?id=2494
When using structured PCDs, a C application is auto generated
to fill in the structured PCD value. The C application uses
the standard include files <stdio.h>, <stdlib.h>, and <string.h>.
This C application also supports include paths from package DEC
files when a structured PCD declaration provides a <Packages>
list. The complete list of include paths are -I options for
include paths from package DEC files and the compiler's standard
include paths.
-I include paths are higher priority than the standard include
paths. If the -I included paths from package DEC files contain
<stdio.h>, <stdlib.h>, or <string.h> the wrong include files are
used to compile the C application for the structured PCD value.
Update GenerateByteArrayValue() to skip a package DEC include
paths that contain <stdio.h>, <stdlib.h>, or <string.h>.
Build failures were observed when adding a structured PCD to
CryptoPkg. CryptoPkg contains <stdio.h>, <stdlib.h>, and
<string.h> in the path CryptoPkg/Library/Include to support
building Open SSL. The Library/Include path is listed as a
private include path in CryptoPkg.dec. Without this change, the
standard include files designed to support build OpenSLL are
used to build the structured PCD C application, and that build
fails.
Other packages that provide a standard C lib or a gasket for
a subset of the standard C lib will run into this same issue
if they also define and use a Structured PCD. So this issue
is not limited to the CryptoPkg.
Cc: Bob Feng <bob.c.feng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The "--function-context" ("-W") option of git-diff displays the entire
body of a modified function, not just small modified hunks within the
function. It is useful for reviewers when the code changes to the function
are small, but they could affect, or depend on, control flow that is far
away in the same function.
Of course, the size of the displayed context can be controlled with the
"-U" option anyway, but such fixed-size contexts are usually either too
small, or too large, in the above scenario.
It turns out that "--function-context" does not work correctly for C
source files in edk2. In particular, labels for the goto instruction
(which the edk2 coding style places in the leftmost column) appear to
terminate "--function-context".
The "git" utility contains built-in hunk header patterns for the C and C++
languages. However, they do not take effect in edk2 because we don't
explicitly assign the "cpp" git-diff driver to our C files. The
gitattributes(5) manual explains that this is required:
> There are a few built-in patterns to make this easier, and
> tex is one of them, so you do not have to write the above in
> your configuration file (you still need to enable this with
> the attribute mechanism, via .gitattributes). The following
> built in patterns are available:
>
> [...]
>
> * cpp suitable for source code in the C and C++
> languages.
The key statement is the one in parentheses.
Grab the suffix lists from the [C-Code-File] and [Acpi-Table-Code-File]
sections of "BaseTools/Conf/build_rule.template", add "*.h" and "*.H", and
mark those as belonging to the "cpp" git-diff driver.
This change has a dramatic effect on the following command, for example:
$ git show -W 2ef0c27cb8
Cc: Bob Feng <bob.c.feng@intel.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200120094245.9010-1-lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif@nuviainc.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
In DxeImageVerificationHandler(), we should return EFI_SECURITY_VIOLATION
for a rejected image only if the platform sets
DEFER_EXECUTE_ON_SECURITY_VIOLATION as the policy for the image's source.
Otherwise, EFI_ACCESS_DENIED must be returned.
Right now, EFI_SECURITY_VIOLATION is returned for all rejected images,
which is wrong -- it causes LoadImage() to hold on to rejected images (in
untrusted state), for further platform actions. However, if a platform
already set DENY_EXECUTE_ON_SECURITY_VIOLATION, the platform will not
expect the rejected image to stick around in memory (regardless of its
untrusted state).
Therefore, adhere to the platform policy in the return value of the
DxeImageVerificationHandler() function.
Furthermore, according to "32.4.2 Image Execution Information Table" in
the UEFI v2.8 spec, and considering that edk2 only supports (AuditMode==0)
at the moment:
> When AuditMode==0, if the image's signature is not found in the
> authorized database, or is found in the forbidden database, the image
> will not be started and instead, information about it will be placed in
> this table.
we have to store an EFI_IMAGE_EXECUTION_INFO record in both the "defer"
case and the "deny" case. Thus, the AddImageExeInfo() call is not being
made conditional on (Policy == DEFER_EXECUTE_ON_SECURITY_VIOLATION); the
documentation is updated instead.
Cc: Chao Zhang <chao.b.zhang@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=2129
Fixes: 5db28a6753
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200116190705.18816-12-lersek@redhat.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
[lersek@redhat.com: push with Mike's R-b due to Chinese New Year
Holiday: <https://edk2.groups.io/g/devel/message/53429>; msgid
<d3fbb76dabed4e1987c512c328c82810@intel.com>]
It makes no sense to call AddImageExeInfo() with (Signature == NULL) and
(SignatureSize > 0). AddImageExeInfo() does not crash in such a case -- it
avoids the CopyMem() call --, but it creates an invalid
EFI_IMAGE_EXECUTION_INFO record. Namely, the
"EFI_IMAGE_EXECUTION_INFO.InfoSize" field includes "SignatureSize", but
the actual signature bytes are not filled in.
Document and ASSERT() this condition in AddImageExeInfo().
In DxeImageVerificationHandler(), zero out "SignatureListSize" if we set
"SignatureList" to NULL due to AllocateZeroPool() failure.
(Another approach could be to avoid calling AddImageExeInfo() completely,
in case AllocateZeroPool() fails. Unfortunately, the UEFI v2.8 spec does
not seem to state clearly whether a signature is mandatory in
EFI_IMAGE_EXECUTION_INFO, if the "Action" field is
EFI_IMAGE_EXECUTION_AUTH_SIG_FAILED or EFI_IMAGE_EXECUTION_AUTH_SIG_FOUND.
For now, the EFI_IMAGE_EXECUTION_INFO addition logic is not changed; we
only make sure that the record we add is not malformed.)
Cc: Chao Zhang <chao.b.zhang@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=2129
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200116190705.18816-11-lersek@redhat.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
[lersek@redhat.com: push with Mike's R-b due to Chinese New Year
Holiday: <https://edk2.groups.io/g/devel/message/53429>; msgid
<d3fbb76dabed4e1987c512c328c82810@intel.com>]
Inside the "for" loop that scans the signatures of the image, we call
HashPeImageByType(), and assign its return value to "Status".
Beyond the immediate retval check, this assignment is useless (never
consumed). That's because a subsequent access to "Status" may only be one
of the following:
- the "Status" assignment when we call HashPeImageByType() in the next
iteration of the loop,
- the "Status = EFI_ACCESS_DENIED" assignment right after the final
"IsVerified" check.
To make it clear that the assignment is only useful for the immediate
HashPeImageByType() retval check, introduce a specific helper variable,
called "HashStatus".
This patch is a no-op, functionally.
Cc: Chao Zhang <chao.b.zhang@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=2129
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200116190705.18816-5-lersek@redhat.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
[lersek@redhat.com: push with Mike's R-b due to Chinese New Year
Holiday: <https://edk2.groups.io/g/devel/message/53429>; msgid
<d3fbb76dabed4e1987c512c328c82810@intel.com>]
The PeCoffLoaderGetImageInfo() function may return various error codes,
such as RETURN_INVALID_PARAMETER and RETURN_UNSUPPORTED.
Such error values should not be assigned to our "Status" variable in the
DxeImageVerificationHandler() function, because "Status" generally stands
for the main exit value of the function. And
SECURITY2_FILE_AUTHENTICATION_HANDLER functions are expected to return one
of EFI_SUCCESS, EFI_SECURITY_VIOLATION, and EFI_ACCESS_DENIED only.
Introduce the "PeCoffStatus" helper variable for keeping the return value
of PeCoffLoaderGetImageInfo() internal to the function. If
PeCoffLoaderGetImageInfo() fails, we'll jump to the "Done" label with
"Status" being EFI_ACCESS_DENIED, inherited from the top of the function.
Note that this is consistent with the subsequent PE/COFF Signature check,
where we jump to the "Done" label with "Status" having been re-set to
EFI_ACCESS_DENIED.
As a consequence, we can at once remove the
Status = EFI_ACCESS_DENIED;
assignment right after the "PeCoffStatus" check.
This patch does not change the control flow in the function, it only
changes the "Status" outcome from API-incompatible error codes to
EFI_ACCESS_DENIED, under some circumstances.
Cc: Chao Zhang <chao.b.zhang@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=2129
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200116190705.18816-4-lersek@redhat.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
[lersek@redhat.com: push with Mike's R-b due to Chinese New Year
Holiday: <https://edk2.groups.io/g/devel/message/53429>; msgid
<d3fbb76dabed4e1987c512c328c82810@intel.com>]
MaxCpuCountInitialization() currently handles the following options:
(1) QEMU does not report the boot CPU count (FW_CFG_NB_CPUS is 0)
In this case, PlatformPei makes MpInitLib enumerate APs up to the
default PcdCpuMaxLogicalProcessorNumber value (64) minus 1, or until
the default PcdCpuApInitTimeOutInMicroSeconds (50,000) elapses.
(Whichever is reached first.)
Time-limited AP enumeration had never been reliable on QEMU/KVM, which
is why commit 45a70db3c3 strated handling case (2) below, in OVMF.
(2) QEMU reports the boot CPU count (FW_CFG_NB_CPUS is nonzero)
In this case, PlatformPei sets
- PcdCpuMaxLogicalProcessorNumber to the reported boot CPU count
(FW_CFG_NB_CPUS, which exports "PCMachineState.boot_cpus"),
- and PcdCpuApInitTimeOutInMicroSeconds to practically "infinity"
(MAX_UINT32, ~71 minutes).
That causes MpInitLib to enumerate exactly the present (boot) APs.
With CPU hotplug in mind, this method is not good enough. Because,
using QEMU terminology, UefiCpuPkg expects
PcdCpuMaxLogicalProcessorNumber to provide the "possible CPUs" count
("MachineState.smp.max_cpus"), which includes present and not present
CPUs both (with not present CPUs being subject for hot-plugging).
FW_CFG_NB_CPUS does not include not present CPUs.
Rewrite MaxCpuCountInitialization() for handling the following cases:
(1) The behavior of case (1) does not change. (No UefiCpuPkg PCDs are set
to values different from the defaults.)
(2) QEMU reports the boot CPU count ("PCMachineState.boot_cpus", via
FW_CFG_NB_CPUS), but not the possible CPUs count
("MachineState.smp.max_cpus").
In this case, the behavior remains unchanged.
The way MpInitLib is instructed to do the same differs however: we now
set the new PcdCpuBootLogicalProcessorNumber to the boot CPU count
(while continuing to set PcdCpuMaxLogicalProcessorNumber identically).
PcdCpuApInitTimeOutInMicroSeconds becomes irrelevant.
(3) QEMU reports both the boot CPU count ("PCMachineState.boot_cpus", via
FW_CFG_NB_CPUS), and the possible CPUs count
("MachineState.smp.max_cpus").
We tell UefiCpuPkg about the possible CPUs count through
PcdCpuMaxLogicalProcessorNumber. We also tell MpInitLib the boot CPU
count for precise and quick AP enumeration, via
PcdCpuBootLogicalProcessorNumber. PcdCpuApInitTimeOutInMicroSeconds is
irrelevant again.
This patch is a pre-requisite for enabling CPU hotplug with SMM_REQUIRE.
As a side effect, the patch also enables S3 to work with CPU hotplug at
once, *without* SMM_REQUIRE.
(Without the patch, S3 resume fails, if a CPU is hot-plugged at OS
runtime, prior to suspend: the FW_CFG_NB_CPUS increase seen during resume
causes PcdCpuMaxLogicalProcessorNumber to increase as well, which is not
permitted.
With the patch, PcdCpuMaxLogicalProcessorNumber stays the same, namely
"MachineState.smp.max_cpus". Therefore, the CPU structures allocated
during normal boot can accommodate the CPUs at S3 resume that have been
hotplugged prior to S3 suspend.)
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Julien Grall <julien.grall@arm.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1515
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20191022221554.14963-4-lersek@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
In v1.5.0, QEMU's "pc" (i440fx) board gained a "CPU present bitmap"
register block. In v2.0.0, this was extended to the "q35" board.
In v2.7.0, a new (read/write) register interface was laid over the "CPU
present bitmap", with an option for the guest to switch the register block
to the new (a.k.a. modern) interface.
Both interfaces are documented in "docs/specs/acpi_cpu_hotplug.txt" in the
QEMU tree.
Add macros for a minimal subset of the modern interface, just so we can
count the possible CPUs (as opposed to boot CPUs) in a later patch in this
series.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1515
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20191022221554.14963-3-lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
https://bugzilla.tianocore.org/show_bug.cgi?id=2484https://bugzilla.tianocore.org/show_bug.cgi?id=2485
Update PatchCheck to not enforce no tabs and not enforce CR/LF
line endings for .gitmodules files. These files are updated by
git when a git submodule command is used and the updates by git
use tab characters and LF line endings.
Also update patch check to not enforce CR/LF line endings for
patch lines that create a submodule directory. These patch
lines use LF line endings. The git submodule directory is
added as a new file with attributes 160000 that can be detected
by looking for the pattern "new file mode 160000".
Cc: Bob Feng <bob.c.feng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1792
HmacXxxInit() is supposed to be initialize user supplied buffer as HMAC
context, as well as user supplied key. Currently it has no real use cases.
Due to BZ1792, the user has no way to get correct size of context buffer
after it's fixed, and then cannot make use of HmacXxxInit to initialize
it.
So it's decided to replace it with HmacXxxSetKey to keep the functionality
of supplying a key to HMAC, but drop all other initialization works. The
user can still get HMAC context via HmacXxxNew interface, which hides the
details about the context.
Cc: Xiaoyu Lu <xiaoyux.lu@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Xiaoyu Lu <xiaoyux.lu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2474
Previous commit d786a17232:
UefiCpuPkg/MpInitLib: Reduce the size when loading microcode patches
Removed the below assignments for the 'InitFlag' field of CPU_MP_DATA
structure in function MpInitLibInitialize() when APs are waken up to do
some initialize sync:
CpuMpData->InitFlag = ApInitReconfig;
...
CpuMpData->InitFlag = ApInitDone;
The above commit mistakenly assumed the 'InitFlag' field will have a value
of 'ApInitDone' when the APs have been successfully waken up before. And
since there is no explicit comparision for the 'InitFlag' field with the
'ApInitReconfig' value. The commit removed those assignments.
However, under some cases (e.g. when variable OldCpuMpData is not NULL,
which means function CollectProcessorCount() will not be called), removing
the above assignments will left the 'InitFlag' field being uninitialized
with a value of 0, which is a invalid value for the type of 'InitFlag'
(AP_INIT_STATE).
It may potentially cause the WakeUpAP() function to run some unnecessary
codes when the APs have been successfully waken up before:
if (CpuMpData->WakeUpByInitSipiSipi ||
CpuMpData->InitFlag != ApInitDone) {
ResetVectorRequired = TRUE;
AllocateResetVector (CpuMpData);
FillExchangeInfoData (CpuMpData);
SaveLocalApicTimerSetting (CpuMpData);
}
This commit will address the above-mentioned issue.
Test done:
* OS boot on a real platform with multi processors
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2421
Capsule Dependency is an incremental change of Fmp Capsule Update. The
capsule format is extended to include a set of binary encoded dependency
expression. The dependency expression is signed together with the Fmp
payload and evaluated before update is applied.
This feature is defined in UEFI Spec 2.8.
The dependency evaluation has two steps:
1. Validate platform existing Fmp images' version satisfy the dependency
expression in capsule image.
2. Validate the capsule image version satisfy all the platform existing
Fmp image's dependency expression.
If the dependency expression evaluates to FALSE, then the capsule update
fails and last attempt status is set to
LAST_ATTEMPT_STATUS_ERROR_UNSATISFIED_DEPENDENCIES.
The dependency saving and getting is FmpDeviceLib implementation scope.
The parameter "Image" of FmpDeviceSetImage and FmpDeviceGetImage function
is extended to contain the dependency. The layout:
+--------------------------+
| Dependency Op-codes |
+--------------------------+
| Fmp Payload Image |
+--------------------------+
1. FmpDeviceSetImage is responsible for retrieving the dependency from the
parameter "Image" and saving it to a protected storage.
2. FmpDeviceGetImage is responsible for retrieving the dependency from the
storage where FmpDeviceSetImage saves dependency and combining it with the
Fmp Payload Image into one buffer which is returned to the caller. This
dependency will be populated into EFI_FIRMWARE_IMAGE_DESCRIPTOR and used
for dependency evaluation.
3. FmpDeviceGetAttributes must set the bit IMAGE_ATTRIBUTE_DEPENDENCY to
indicate the Fmp device supports Fmp Capsule Dependency feature.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Wei6 Xu <wei6.xu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2421
Add new definitions for Fmp Capsule dependency in UEFI Spec 2.8.
1. Extend the Last Attempt Status with a value to indicate the firmware
update fails with unsatisfied dependencies.
2. Add the definition of dependency expression op-codes.
3. Add the definition of EFI_FIRMWARE_IMAGE_DEP which is an array of FMP
dependency expression op-codes.
4. Extend the EFI_FIRMWARE_IMAGE_DESCRIPTOR with a pointer to the array of
FMP dependency expression op-codes.
5. Extend the Image Attribute Definitions with IMAGE_ATTRIBUTE_DEPENDENCY
to indicate that there is and EFI_FIRMWARE_IMAGE_DEP section associated
with the image.
6. Update EFI_FIRMWARE_IMAGE_DESCRIPTOR_VERSION to 4.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Wei6 Xu <wei6.xu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
In commit 4eee0cc7cc ("UefiCpuPkg/PiSmmCpu: Enable 5 level paging when
CPU supports", 2019-07-12), the Page Directory Entry setting was regressed
(corrupted) when splitting a 2MB page to 512 4KB pages, in the
InitPaging() function.
Consider the following hunk, displayed with
$ git show --function-context --ignore-space-change 4eee0cc7cc
> //
> // If it is 2M page, check IsAddressSplit()
> //
> if (((*Pd & IA32_PG_PS) != 0) && IsAddressSplit (Address)) {
> //
> // Based on current page table, create 4KB page table for split area.
> //
> ASSERT (Address == (*Pd & PHYSICAL_ADDRESS_MASK));
>
> Pt = AllocatePageTableMemory (1);
> ASSERT (Pt != NULL);
>
> + *Pd = (UINTN) Pt | IA32_PG_RW | IA32_PG_P;
> +
> // Split it
> - for (PtIndex = 0; PtIndex < SIZE_4KB / sizeof(*Pt); PtIndex++) {
> - Pt[PtIndex] = Address + ((PtIndex << 12) | mAddressEncMask | PAGE_ATTRIBUTE_BITS);
> + for (PtIndex = 0; PtIndex < SIZE_4KB / sizeof(*Pt); PtIndex++, Pt++) {
> + *Pt = Address + ((PtIndex << 12) | mAddressEncMask | PAGE_ATTRIBUTE_BITS);
> } // end for PT
> *Pd = (UINT64)(UINTN)Pt | mAddressEncMask | PAGE_ATTRIBUTE_BITS;
> } // end if IsAddressSplit
> } // end for PD
First, the new assignment to the Page Directory Entry (*Pd) is
superfluous. That's because (a) we set (*Pd) after the Page Table Entry
loop anyway, and (b) here we do not attempt to access the memory starting
at "Address" (which is mapped by the original value of the Page Directory
Entry).
Second, appending "Pt++" to the incrementing expression of the PTE loop is
a bug. It causes "Pt" to point *right past* the just-allocated Page Table,
once we finish the loop. But the PDE assignment that immediately follows
the loop assumes that "Pt" still points to the *start* of the new Page
Table.
The result is that the originally mapped 2MB page disappears from the
processor's view. The PDE now points to a "Page Table" that is filled with
garbage. The random entries in that "Page Table" will cause some virtual
addresses in the original 2MB area to fault. Other virtual addresses in
the same range will no longer have a 1:1 physical mapping, but be
scattered over random physical page frames.
The second phase of the InitPaging() function ("Go through page table and
set several page table entries to absent or execute-disable") already
manipulates entries in wrong Page Tables, for such PDEs that got split in
the first phase.
This issue has been caught as follows:
- OVMF is started with 2001 MB of guest RAM.
- This places the main SMRAM window at 0x7C10_1000.
- The SMRAM management in the SMM Core links this SMRAM window into
"mSmmMemoryMap", with a FREE_PAGE_LIST record placed at the start of the
area.
- At "SMM Ready To Lock" time, PiSmmCpuDxeSmm calls InitPaging(). The
first phase (quoted above) decides to split the 2MB page at 0x7C00_0000
into 512 4KB pages, and corrupts the PDE. The new Page Table is
allocated at 0x7CE0_D000, but the PDE is set to 0x7CE0_E000 (plus
attributes 0x67).
- Due to the corrupted PDE, the second phase of InitPaging() already looks
up the PTE for Address=0x7C10_1000 in the wrong place. The second phase
goes on to mark bogus PTEs as "NX".
- PiSmmCpuDxeSmm calls SetMemMapAttributes(). Address 0x7C10_1000 is at
the base of the SMRAM window, therefore it happens to be listed in the
SMRAM map as an EfiConventionalMemory region. SetMemMapAttributes()
calls SmmSetMemoryAttributes() to mark the region as XP. However,
GetPageTableEntry() in ConvertMemoryPageAttributes() fails -- address
0x7C10_1000 is no longer mapped by anything! -- and so the attribute
setting fails with RETURN_UNSUPPORTED. This error goes unnoticed, as
SetMemMapAttributes() ignores the return value of
SmmSetMemoryAttributes().
- When SetMemMapAttributes() reaches another entry in the SMRAM map,
ConvertMemoryPageAttributes() decides it needs to split a 2MB page, and
calls SplitPage().
- SplitPage() calls AllocatePageTableMemory() for the new Page Table,
which takes us to InternalAllocMaxAddress() in the SMM Core.
- The SMM core attempts to read the FREE_PAGE_LIST record at 0x7C10_1000.
Because this virtual address is no longer mapped, the firmware crashes
in InternalAllocMaxAddress(), when accessing (Pages->NumberOfPages).
Remove the useless assignment to (*Pd) from before the loop. Revert the
loop incrementing and the PTE assignment to the known good version.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1789335
Fixes: 4eee0cc7cc
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2457
This commit fixes an offset calculation that is used to write the
VarErrorFlag UEFI variable to the UEFI variable runtime cache.
Currently a physical address is used instead of an offset. This
commit changes the offset to zero with a length of the entire
non-volatile variable store so the entire non-volatile variable
store buffer in SMRAM (with the variable update modification) is
copied to the runtime variable cache. This follows the same pattern
used in other SynchronizeRuntimeVariableCache () calls for
consistency.
* Observable symptom: An exception in SMM will most likely occur
due to the invalid memory reference when the VarErrorFlag variable
is written. The variable is most commonly written when the UEFI
variable store is full.
* The issue only occurs when the variable runtime cache is enabled
by the following PCD being set to TRUE:
gEfiMdeModulePkgTokenSpaceGuid.PcdEnableVariableRuntimeCache
Fixes: aab3b9b9a1
Cc: Liming Gao <liming.gao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Michael Turner <michael.turner@microsoft.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Michael Kubacki <michael.a.kubacki@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
#if MACRO is not good style. It should be changed to
#ifdef MACRO style or #if defined (MACRO) style.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Add support for revision 3 of System Resource Affinity Table (SRAT).
Decode and dump the new Generic Initiator Affinity Structure.
Validate the Device Handle Type field inside the Generic Initiator
Affinity Structure.
Reviewed-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Reviewed-by: Jaben Carsey <jaben.carsey@intel.com>
Reviewed-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
Tested-by: Sudipto Paul <sudipto.paul@arm.com>
Signed-off-by: Krzysztof Koch <krzysztof.koch@arm.com>
While the alternative PEI-less SEC implementation in PrePi already
takes the EnableVFP PCD into account, the PrePeiCore code does not,
and so we may end up triggering synchronous exception when code
attempts to use FP or SIMD registers, which is permitted on AARCH64
by the spec.
So enable the VFP as early as feasible if the associated PCD is set.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
EnterS3WithImmediateWake () no longer has any callers, so remove it
from ResetSystemLib. Note that this means the hack to support warm
reboot by jumping to the SEC entry point with the MMU and caches off
is also no longer used, and can be removed as well, along with the PCD
PcdArmReenterPeiForCapsuleWarmReboot that was introduced for this
purpose.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
When downloading over TLS, each TLS message ("APP packet") is returned as
a (decrypted) fragment table by EFI_TLS_PROTOCOL.ProcessPacket().
The TlsProcessMessage() function in "NetworkPkg/HttpDxe/HttpsSupport.c"
linearizes the fragment table into a single contiguous data block. The
resultant flat data block contains both TLS headers and data.
The HttpsReceive() function parses the actual application data -- in this
case: decrypted HTTP data -- out of the flattened TLS data block, peeling
off the TLS headers.
The HttpResponseWorker() function in "NetworkPkg/HttpDxe/HttpImpl.c"
propagates this HTTP data outwards, implementing the
EFI_HTTP_PROTOCOL.Response() function.
Now consider the following documentation for EFI_HTTP_PROTOCOL.Response(),
quoted from "MdePkg/Include/Protocol/Http.h":
> It is the responsibility of the caller to allocate a buffer for Body and
> specify the size in BodyLength. If the remote host provides a response
> that contains a content body, up to BodyLength bytes will be copied from
> the receive buffer into Body and BodyLength will be updated with the
> amount of bytes received and copied to Body. This allows the client to
> download a large file in chunks instead of into one contiguous block of
> memory.
Note that, if the caller-allocated buffer is larger than the
server-provided chunk, then the transfer length is limited by the latter.
This is in fact the dominant case when downloading a huge file (for which
UefiBootManagerLib allocated a huge contiguous RAM Disk buffer) in small
TLS messages.
For adjusting BodyLength as described above -- i.e., to the application
data chunk that has been extracted from the TLS message --, the
HttpResponseWorker() function employs the following assignment:
HttpMsg->BodyLength = MIN (Fragment.Len, (UINT32) HttpMsg->BodyLength);
The (UINT32) cast is motivated by the MIN() requirement -- in
"MdePkg/Include/Base.h" -- that both arguments be of the same type.
"Fragment.Len" (NET_FRAGMENT.Len) has type UINT32, and
"HttpMsg->BodyLength" (EFI_HTTP_MESSAGE.BodyLength) has type UINTN.
Therefore a cast is indeed necessary.
Unfortunately, the cast is done in the wrong direction. Consider the
following circumstances:
- "Fragment.Len" happens to be consistently 16KiB, dictated by the HTTPS
Server's TLS stack,
- the size of the file to download is 4GiB + N*16KiB, where N is a
positive integer.
As the download progresses, each received 16KiB application data chunk
brings the *next* input value of BodyLength closer down to 4GiB. The cast
in MIN() always masks off the high-order bits from the input value of
BodyLength, but this is no problem because the low-order bits are nonzero,
therefore the MIN() always permits progress.
However, once BodyLength reaches 4GiB exactly on input, the MIN()
invocation produces a zero value. HttpResponseWorker() adjusts the output
value of BodyLength to zero, and then passes it to HttpParseMessageBody().
HttpParseMessageBody() (in "NetworkPkg/Library/DxeHttpLib/DxeHttpLib.c")
rejects the zero BodyLength with EFI_INVALID_PARAMETER, which is fully
propagated outwards, and aborts the HTTPS download. HttpBootDxe writes the
message "Error: Unexpected network error" to the UEFI console.
For example, a file with size (4GiB + 197MiB) terminates after downloading
just 197MiB.
Invert the direction of the cast: widen "Fragment.Len" to UINTN.
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Maciej Rabeda <maciej.rabeda@linux.intel.com>
Cc: Siyuan Fu <siyuan.fu@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Reviewed-by: Siyuan Fu <siyuan.fu@intel.com>
Reviewed-by: Maciej Rabeda <maciej.rabeda@linux.intel.com>
The LoadFile protocol can report such a large buffer size that we cannot
allocate enough reserved pages for. This particularly affects HTTP(S)
Boot, if the remote file is very large (for example, an ISO image).
While the TianoCore wiki mentions this at
<https://github.com/tianocore/tianocore.github.io/wiki/HTTP-Boot#ram-disk-image-size>:
> The maximum RAM disk image size depends on how much continuous reserved
> memory block the platform could provide.
it's hard to remember; so log a DEBUG_ERROR message when the allocation
fails.
This patch produces error messages such as:
> UiApp:BmExpandLoadFile: failed to allocate reserved pages:
> BufferSize=4501536768
> LoadFile="PciRoot(0x0)/Pci(0x3,0x0)/MAC(5254001B103E,0x1)/
> IPv4(0.0.0.0,TCP,DHCP,192.168.124.106,192.168.124.1,255.255.255.0)/
> Dns(192.168.124.1)/
> Uri(https://ipv4-server/RHEL-7.7-20190723.1-Server-x86_64-dvd1.iso)"
> FilePath=""
(Manually rewrapped here for keeping PatchCheck.py happy.)
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Reviewed-by: Siyuan Fu <siyuan.fu@intel.com>
Acked-by: Hao A Wu <hao.a.wu@intel.com>
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=2455
BuildOption is used by TargetTxtClassObj.py
GenFdsOption is used by GenFds.py
When the GenFds tool is used alone (e.g. python3 -m GenFds.GenFds -h)
With the OptionParser function, the first detected function
prints the help message
import TargetTxtClassObj to GenFds,
The BuildOption will be executed and replace GenFdsOption
We removed all objects associated with this problem that
were created directly during the import process
(e.g. BuildOption, BuildTarget = MyOptionParser(),
TargetTxt = TargetTxtDict())
The Patch is going to fix this issue
Signed-off-by: Zhiju.Fan <zhijux.fan@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Bob Feng <bob.c.feng@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
Changed @rtval to @retval in SdMmcHcStartSdClock
function description.
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
EnterS3WithImmediateWake () no longer has any callers, so remove it
from ResetSystemLib.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
EnterS3WithImmediateWake () no longer has any callers, so remove it
from ResetSystemLib.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
EnterS3WithImmediateWake () no longer has any callers, so remove it
from ResetSystemLib.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Guo Dong <guo.dong@intel.com>
EnterS3WithImmediateWake () no longer has any callers, so remove it
from ResetSystemLib.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
EnterS3WithImmediateWake () no longer has any callers, so remove it
from ResetSystemLib.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The existing MpInitLib will shadow the microcode update patches from
flash to memory and this is done by searching microcode region specified
by PCD PcdCpuMicrocodePatchAddress and PcdCpuMicrocodePatchRegionSize.
This brings a limition to platform FW that all the microcode patches must
be placed in one continuous flash space.
This patch shadows microcode update according to FIT microcode entries if
it's present, otherwise it will fallback to original logic (by PCD).
A new featured PCD gUefiCpuPkgTokenSpaceGuid.PcdCpuShadowMicrocodeByFit
is added for enabling/disabling this support.
TEST: Tested on FIT enabled platform.
BZ: https://tianocore.acgmultimedia.com/show_bug.cgi?id=2449
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Siyuan Fu <siyuan.fu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
To avoid patches committed with incorrect email address,
use the EmailAddressCheck class on the author email too.
Example:
$ python BaseTools/Scripts/PatchCheck.py 1a04951309
Checking git commit: 1a04951309
The 'Author' email address is not valid:
* The email address cannot contain a space: /o=Intel/ou=External \
(FYDIBOHF25SPDLT)/cn=Recipients/cn=fe425ca7e5f4401abed22b904fe5d964
Cc: Bob Feng <bob.c.feng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
We are checking different emails from the signature list. We are
going to check more. To be able to differency, add a description
field, so the error reported is clearer.
Cc: Bob Feng <bob.c.feng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
The HII pages that are part of Tcg2ConfigDxe expect the following PCDs
to be of dynamic HII type, so declare them as such.
gEfiSecurityPkgTokenSpaceGuid.PcdTcgPhysicalPresenceInterfaceVer
gEfiSecurityPkgTokenSpaceGuid.PcdTpm2AcpiTableRev
Currently, the TPM2 ACPI table is not produced, since we do not
incorporate the Tcg2Smm module, which implements the SMI based
physical presence interface exposed to the OS.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Put the TPM2 related DXE modules together in the DSC, and add a
TPM2 support header comment while at it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Add edk2 platform boot manager protocol which would have platform
specific refreshes to the auto enumerated as well as NV boot options
for the platform.
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
This patch updates the microcode loader to always perform a microcode
detect and load on both BSP and AP processor. This is to fix a potential
microcode revision mismatch issue in below situation:
1. Assume there are two microcode co-exists in flash: one production
version and one debug version microcode.
2. FIT loads production microcode to BSP and all AP.
3. UefiCpuPkg loader loads debug microcode to BSP, and skip the loading
on AP.
As a result, different microcode patches are loaded to BSP and AP, and
trigger microcode mismatch error during OS boot.
BZ link: https://bugzilla.tianocore.org/show_bug.cgi?id=2431
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Siyuan Fu <siyuan.fu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
This patch removes the unnecessary alignment check on microcode patch
TotalSize introduced by commit d786a172. The TotalSize has already been
checked with 1K alignment and MAX_ADDRESS in previous code as below:
if ( (UINTN)MicrocodeEntryPoint > (MAX_ADDRESS - TotalSize) ||
((UINTN)MicrocodeEntryPoint + TotalSize) > MicrocodeEnd ||
(DataSize & 0x3) != 0 ||
(TotalSize & (SIZE_1KB - 1)) != 0 ||
TotalSize < DataSize
) {
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Siyuan Fu <siyuan.fu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2434
Current code use below loops to enumerate the CPUs:
for (Index = mMaxNumberOfCpus; Index-- > 0;) {
it has no issue but not easy for the developers to read the code.
Update above code to below style,
for (Index = 0; Index < mMaxNumberOfCpus; Index++) {
It make the developers easy to read and consistent with other
similar cases in this driver.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
We use .mailmap to display contributors email addresses in an
uniform format.
Add an entry for Ray Ni to have his/her name and email address
displayed properly in the git history.
Cc: Ray Ni <ray.ni@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20200106115415.11624-26-philmd@redhat.com>
We use .mailmap to display contributors email addresses in an
uniform format.
Add an entry for Philippe Mathieu-Daudé to have his/her name and
email address displayed properly in the git history.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20200106115415.11624-25-philmd@redhat.com>
[lersek@redhat.com: translit subject to ASCII to suppress PatchCheck.py]
We use .mailmap to display contributors email addresses in an
uniform format.
Add an entry for Nikolai Saoukh to have his/her name and email
address displayed properly in the git history.
Cc: Nikolai Saoukh <nms@otdel-1.org>
Reviewed-by: Nikolai Saoukh <nms@otdel-1.org>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20200106115415.11624-24-philmd@redhat.com>
We use .mailmap to display contributors email addresses in an
uniform format.
Add an entry for Marvin Häuser to have his/her name and email
address displayed properly in the git history (in particular,
commit 62ec4a5e).
Cc: Marvin Häuser <Marvin.Haeuser@outlook.de>
Cc: Marvin Häuser <Marvin.Haeuser@outlook.com>
Reviewed-by: Marvin Häuser <mhaeuser@outlook.de>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20200106115415.11624-20-philmd@redhat.com>
[lersek@redhat.com: translit subject to ASCII to suppress PatchCheck.py]
We use .mailmap to display contributors email addresses in an
uniform format.
Add an entry for Marc-André Lureau to have his/her name and email
address displayed properly in the git history.
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20200106115415.11624-19-philmd@redhat.com>
[lersek@redhat.com: translit subject to ASCII to suppress PatchCheck.py]
We use .mailmap to display contributors email addresses in an
uniform format.
Add an entry for Laszlo Ersek to have his/her name and email
address displayed properly in the git history.
Cc: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20200106115415.11624-16-philmd@redhat.com>
We use .mailmap to display contributors email addresses in an
uniform format.
Add an entry for Baraneedharan Anbazhagan to have his/her name
and email address displayed properly in the git history.
Cc: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Reviewed-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20200106115415.11624-7-philmd@redhat.com>
We use .mailmap to display contributors email addresses in an
uniform format.
Add an entry for Antoine Cœur to have his/her name and email
address displayed properly in the git history.
Cc: Antoine Cœur <coeur@gmx.fr>
Reviewed-by: Antoine Cœur <coeur@gmx.fr>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20200106115415.11624-4-philmd@redhat.com>
[lersek@redhat.com: fix up valid PatchCheck.py error in Reviewed-by]
[lersek@redhat.com: translit subject to ASCII to suppress PatchCheck.py]
The endpoint selected by the driver needs to not
only be an interrupt type, but have direction IN
as required to set up an asynchronous interrupt transfer.
Currently, the driver assumes that the first INT endpoint
will be of type IN, but that is not true of all devices,
and will silently fail on devices which have the OUT endpoint
before the IN. Adjust the endpoint selection loop to explictly
check for direction IN.
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
The endpoint selected by the driver needs to not
only be an interrupt type, but have direction IN
as required to set up an asynchronous interrupt transfer.
Currently, the driver assumes that the first INT endpoint
will be of type IN, but that is not true of all devices,
and will silently fail on devices which have the OUT endpoint
before the IN. Adjust the endpoint selection loop to explictly
check for direction IN.
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: GuoMinJ <newexplorerj@gmail.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
The endpoint selected by the driver needs to not
only be an interrupt type, but have direction IN
as required to set up an asynchronous interrupt transfer.
Currently, the driver assumes that the first INT endpoint
will be of type IN, but that is not true of all devices,
and will silently fail on devices which have the OUT endpoint
before the IN. Adjust the endpoint selection loop to explictly
check for direction IN.
Test: detachable keyboard on Google Pixel Slate now works.
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: GuoMinJ <newexplorerj@gmail.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2439
The TCG2 DXE supports to parse the 800-155 event GUID from PEI
and puts to the beginning of the TCG2 event.
The TCG2 DXE also supports a DXE driver produces 800-155 event
and let TCG2 DXE driver record.
The 800-155 is a NO-ACTION event which does not need extend
anything to TPM2. The TCG2 DXE also supports that.
Multiple 800-155 events are supported. All of them will be put
to the beginning of the TCG2 event, just after the SpecId event.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
For eMMC modules we used to notify the platform about frequency
change only after sending CMD13 which meant that platform
might not get a chance to apply required post frequency
change fixes to get the clock stable. To fix this
notification has been moved to SdMmcHcClockSupply function
just after we start the SD clock. During first time setup
the notification won't be sent to avoid changing old behavior.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Tested-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2388
Token is new introduced by MM MP Protocol. Current logic allocate Token
every time when need to use it. The logic caused SMI latency raised to
very high. Update logic to allocate Token buffer at driver's entry point.
Later use the token from the allocated token buffer. Only when all the
buffer have been used, then need to allocate new buffer.
Former change (9caaa79dd7) missed
PROCEDURE_TOKEN part, this change covers it.
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Add PS2 keyboard support.
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2316
This patch adds PS2 keyboard support in boot manager, and
add a build flag PS2_KEYBOARD_ENABLE for PS2 keyboard to
build PS2 keyboard driver and SIO driver. Be default the
build flag is not enabled since PS2 keyboard is not common
used. could use -DPS2_KEYBOARD_ENABLE to enable build it
if need this feature.
Signed-off-by: Guo Dong <guo.dong@intel.com>
Reviewed-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Benjamin You <benjamin.you@intel.com>
Previous commits have introduced below fields in structure CPU_AP_DATA:
UINT32 ProcessorSignature;
UINT8 PlatformId;
UINT64 MicrocodeEntryAddr;
which store the information of:
A. CPUID
B. Platform ID
C. Detected microcode patch entry address (including the microcode patch
header)
for each processor within system.
Therefore, the below fields in structure CPU_MP_DATA:
UINT32 ProcessorSignature;
UINT32 ProcessorFlags;
UINT64 MicrocodeDataAddress;
UINT32 MicrocodeRevision;
which store the BSP's information of:
A. CPUID
B. Platform ID
C. The address and revision of detected microcode patch
are redundant and can be removed.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Siyuan Fu <siyuan.fu@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The below 2 microcode patch related fields in structure CPU_MP_DATA:
UINT64 MicrocodePatchAddress;
UINT64 MicrocodePatchRegionSize;
They will be passed from PEI phase and be reused DXE phase.
Previously, these 2 fields were placed after some fields with type
'UINTN', this will lead to different field offset in different
architecture for them.
This commit will move them before the fields with different size in
different architecture to ensure they can be properly used in DXE phase.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Siyuan Fu <siyuan.fu@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2430
This commit will add the definitions for EDKII microcode patch HOB.
The intention of adding this HOB is to provide a scheme to store the below
information:
A. The base address and size of the microcode patches that are being
loaded (from flash) into memory;
B. The information of detected microcode patch for each processor within
the system.
The producer of the HOB will be the UefiCpuPkg/MpInitLib (where the load,
detect and apply of the microcode happen). The consumer of the HOB can be
modules that want to detect/apply the microcode patch by themselves again
later during the boot flow.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Siyuan Fu <siyuan.fu@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2429
This commit will attempt to reduce the copy size when loading the
microcode patches data from flash into memory.
Such optimization is done by a pre-process of the microcode patch headers
(on flash). A microcode patch will be loaded into memory only when the
below 3 criteria are met:
A. With a microcode patch header (which means the data is not padding data
between microcode patches);
B. The 'ProcessorSignature' & 'ProcessorFlags' fields in the header match
at least one processor within system;
C. If the Extended Signature Table exists in a microcode patch, the
'ProcessorSignature' & 'ProcessorFlag' fields in the table entries
match at least one processor within system.
Criterion B and C will require all the processors to be woken up once to
collect their CPUID and Platform ID information. Hence, this commit will
move the copy, detect and apply of microcode patch on BSP and APs after
all the processors have been woken up.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Siyuan Fu <siyuan.fu@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
If git finds a '\r' character in the message, then it
converts the entire message content into Quoted-Printable
encoding. It appears that when groups.io converts the QP
encoding back to text format, the '\r' characters somehow
become '\n'. To workaround this, the SetupGit.py script
will now explicitly set the sendemail.transferEncoding git
config option to '8bit'
Signed-off-by: Nate DeSimone <nathaniel.l.desimone@intel.com>
Cc: Bob Feng <bob.c.feng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
The size for the array of mSmmMpSyncData->CpuData[] is 0 ~
mMaxNumberOfCpus -1. But current code may use
mSmmMpSyncData->CpuData[mMaxNumberOfCpus].
This patch fixed this issue.
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2268
In current implementation, when check whether APs called by StartUpAllAPs
or StartUpThisAp, it checks the Tokens value used by other APs. Also the AP
will update the Token value for itself if its task finished. In this
case, the potential race condition issues happens for the tokens.
Because of this, system may trig ASSERT during cycling test.
This change enhance the code logic, add new attributes for the token to
remove the reference for the tokens belongs to other APs.
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
This issue happens under two conditions.
1. Unicode language environment in Windows
2. Python2 (Not reproducible with Python3)
Step to reproduce
C:\edk2>edksetup.bat forcerebuild
The edksetup.bat stuck at 'nmake cleanall'.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
The latest TCG PFP specification (TCG PC Client Platform Firmware Profile
Specification, Revision 1.05) added new data structure. For example,
the SPDM device measurement. This patch adds the new content.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=2311
In patch set 13c5e34a - 0c3e8e99, we implemented incremental build with
using compiler/pre-processor generate dependent header file function.
A issue is found for MSVC compiler, that the cl.exe /showIncludes
build option generate header file list to either stdout or stderr.
For .c file, the header file list is print out to stdout while for
.vfr, .aslc and .nasm file, the file list is print out to stderr.
The build tool use two threads to process the message from stdout and
stderr, but to generate correct *.deps file, build tool need to
combine the header file list from stderr and other messages from stdout
together with correct time sequence order.
So this patch is trying to combine the stdout and stderr together for
the process which is for calling make program.
The impact of this patch is that the output message of build with -q
will be changed. The compiler error message will not print out.
The build behavior of other log level setting will not be impacted.
Signed-off-by: Bob Feng <bob.c.feng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Steven Shi <steven.shi@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=2423
That commit 13c5e34a1b introduces the first two UTF-8
characters (the quote ') in an otherwise all-ascii file.
In Conf\tools_def.template
There is tow lines of
Notes: Since this tool chain is obsolete, it doesn't enable
the compiler option for included header file list generation,
we replaces the two offending quotes by proper ascii quotes
The patch is going to fix this issue
Signed-off-by: Zhiju.Fan <zhijux.fan@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Bob Feng <bob.c.feng@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=2371
This patch is to fix a regression issue that build fails
if multiple build targets given.
Two changes cause this regression issue.
One is AutoGen object __hash__ function only
hash file path and arch, missing ToolChain and build target.
The other is changing the multiple-thread-genfds function as default
build behavior. To generate the genffs command to Makefile, there
is a global data set is used, GenFdsGlobalVariable, which cause build
tool use the data of first build-target build in
the second build-target build.
Signed-off-by: Bob Feng <bob.c.feng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Steven Shi <steven.shi@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
As per the Microsoft Debug Port Table 2 (DBG2) documentation, that
can be found online, we are missing 2 serial interface types for
Arm DCC and Bcm2835 (the latter being used with the Raspberry Pi).
These same types are present in DebugPort2Table.h so add them to
SerialPortConsoleRedirectionTable.h too.
Note that we followed the same idiosyncrasies as DebugPort2Table
for naming these new macros.
Signed-off-by: Pete Batard <pete@akeo.ie>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
PI defines a few architected events that have significance in the MM
context as well as in the non-secure DXE context. So register notify
handlers for these events, and relay them into the standalone MM world.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Achin Gupta <achin.gupta@arm.com>
Redesign the binary cache and not need to save the
cache intermediate result and state in memory as a
ModuleBuildCacheIR class instance. So remove the
CacheIR.py which define the ModuleBuildCacheIR class.
Signed-off-by: Steven Shi <steven.shi@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Bob Feng <bob.c.feng@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
Redesign the binary cache and bases on the compiler to
output the dependency header files info for every module.
The binary cache will directly consume the dependency header
files info and doesn't parse the C source code by iteself.
Also redesign the dependency files list format for module
and try to share the common lib hash result as more as
possible in local process. Remove the unnecessary share data
access across multiprocessing.
Signed-off-by: Steven Shi <steven.shi@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Bob Feng <bob.c.feng@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
Binary cache use the OutputFile method to return the module
built output files needed to store in cache, but current
OutputFile implementation doesn't return complete output files.
Enhance the OutputFile method to return more complete output files.
Signed-off-by: Steven Shi <steven.shi@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Bob Feng <bob.c.feng@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
Implement a version of the EDK2 IoMmu protocol that is a simple wrapper
around DmaLib. This is intended to be used to wrap NonCoherentDmaLib so
that the generic PCI infrastructure can be used to implement support for
non cache-coherent DMA.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Tested-by: Pete Batard <pete@akeo.ie>
Implement support for driving peripherals with limited DMA ranges to
NonCoherentDmaLib, by adding a device address limit, and taking it,
along with the device offset, into account when allocating or mapping
DMA buffers.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Pete Batard <pete@akeo.ie>
Acked-by: Philippe Mathieu-Daude <philmd@redhat.com>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2388
Token is new introduced by MM MP Protocol. Current logic allocate Token
every time when need to use it. The logic caused SMI latency raised to
very high. Update logic to allocate Token buffer at driver's entry point.
Later use the token from the allocated token buffer. Only when all the
buffer have been used, then need to allocate new buffer.
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2304
The following statement produces a SyntaxWarning with Python 3.8:
if str(FdRegion.RegionType) is 'FILE' and self.Platform.VpdToolGuid in \
str(FdRegion.RegionDataList):
BaseTools/Source/Python/AutoGen/WorkspaceAutoGen.py:168: SyntaxWarning: \
"is" with a literal. Did you mean "=="?
Change the 'is' operator by the conventional '==' comparator.
Cc: Bob Feng <bob.c.feng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
Signed-off-by: Philippe Mathieu-Daude <philmd@redhat.com>
Third party driver images loaded from Option ROM get queued
for execution after EndOfDxe. These queued images need to be
dispatched from the PlatformBootManagerLib.
Since the queued images were not dispatched, the PCI Option
ROM drivers were not getting loaded on Juno. Therefore,
add call to EfiBootManagerDispatchDeferredImages() for
dispatching deferred images from PlatformBootManagerLib.
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1965
For function InsertNewGuidNameMapping, it rellocate the
mGuidList with new size
"mGuidListCount+1 * sizeof(GUID_INFO_BLOCK)". That isn't
its purpose and would cause a overflow operation in
"mGuidList[mGuidListCount - 1].xxx = xxx". Its purpose
is to increase 1 block size of mGuidList. Change it to
"(mGuidListCount + 1) * sizeof (GUID_INFO_BLOCK)".
Adjust the coding style of this function.
Cc: Jaben Carsey <jaben.carsey@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Andrew Fish <afish@apple.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Updated IORT parser to conform to the IO Remapping
Table, Platform Design Document, Revision D, March 2018.
The following structure parsers have been updated:
1. SMMUv3 - added proximity domain and device Id
mapping index.
2. RootComplex - added memory address size limit.
2. PMCG - added page 1 support.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Add support for parsing the ACPI FACS table.
The FADT parser has also been updated as it
links the FACS table using the FIRMWARE_CTRL
or X_FIRMWARE_CTRL fields.
Since the FACS table does not follow the standard
ACPI header, the FADT parser extracts the FACS
signature, length and version fields before invoking
the FACS parser.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=2400
In Dsc Parser, included dsc file is parsed always no matter
if its condition is False
gUefiOvmfPkgTokenSpaceGuid.test1|FALSE
!if gUefiOvmfPkgTokenSpaceGuid.test1 == FALSE
!include OvmfPkg/test1.dsc
!else
!include OvmfPkg/test2.dsc
!endif
The patch avoids processing redundant dsc files and improves
the way Tool handles them.
In the above case, since the conditional result is FALSE,
"test2.dsc" is not parsed.
Signed-off-by: Zhiju.Fan <zhijux.fan@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Bob Feng <bob.c.feng@intel.com>
Reviewed-by: Bob Feng <bob.c.feng@intel.com>
Commit 8906f076de ("CryptoPkg/OpensslLib: Add missing header files in
INF file", 2019-08-16) incorrectly placed "ms/uplink.h" in the
auto-generated part of [Sources], in "OpensslLib.inf".
("ms/uplink.h" was added in the right spot in "OpensslLibCrypto.inf".)
Subsequently, when commit 9f4fbd56d4 ("CryptoPkg/OpensslLib: Update
process_files.pl to generate .h files", 2019-10-30) re-generated that part
of "OpensslLib.inf", the "ms/uplink.h" file reference was lost. This
triggers a warning from the "build" utility now.
Name the header file in the right spot in [Sources].
This change makes "OpensslLib.inf" consistent with "OpensslLibCrypto.inf".
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Shenglei Zhang <shenglei.zhang@intel.com>
Cc: Xiaoyu Lu <xiaoyux.lu@intel.com>
Fixes: 8906f076de
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
When diffing "OpensslLib.inf" against "OpensslLibCrypto.inf", the *only*
differences should be:
- BASE_NAME, MODULE_UNI_FILE, and FILE_GUID are expected to differ, in
[Defines];
- "OpensslLib.inf" is expected to list "$(OPENSSL_PATH)/ssl/..." source
files in the auto-generated part of the [Sources] section.
Commit 8906f076de ("CryptoPkg/OpensslLib: Add missing header files in
INF file", 2019-08-16) broke that invariant, by adding "buildinf.h" and
"rand_pool_noise.h" in different order to both INF files.
Fix that order in "OpensslLib.inf" now. (Note that this does not
re-establish full consistency between both INF files -- it just highlights
another problem, which we'll fix in the next patch.)
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Shenglei Zhang <shenglei.zhang@intel.com>
Cc: Xiaoyu Lu <xiaoyux.lu@intel.com>
Fixes: 8906f076de
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
# If Build Rule's version is less than the version number required by the tools, halting the build.
EdkLogger.error("build",AUTOGEN_ERROR,
ExtraData="The version number [%s] of build_rule.txt is less than the version number required by the AutoGen.(the minimum required version number is [%s])"\
# If Build Rule's version is less than the version number required by the tools, halting the build.
EdkLogger.error("build",AUTOGEN_ERROR,
ExtraData="The version number [%s] of build_rule.txt is less than the version number required by the AutoGen.(the minimum required version number is [%s])"\
%(RetVal._FileVersion,AutoGenReqBuildRuleVerNum))
self._ToolBuildRule=RetVal
# This acts like the main() function for the script, unless it is 'import'ed into another
help="ARCHS is one of list: IA32, X64, ARM, AARCH64 or EBC, which overrides target.txt's TARGET_ARCH definition. To specify more archs, please repeat this option.")
help="Build the module specified by the INF file name argument.")
Parser.add_option("-b","--buildtarget",type="string",dest="BuildTarget",help="Using the TARGET to build the platform, overriding target.txt's TARGET definition.",
help="Build the platform using multi-threaded compiler. The value overrides target.txt's MAX_CONCURRENT_THREAD_NUMBER. When value is set to 0, tool automatically detect number of "\
"processor threads, set value to 1 means disable multi-thread build, and set value to more than 1 means user specify the threads number to build.")
help="Flags that control the type of build report to generate. Must be one of: [PCD, LIBRARY, FLASH, DEPEX, BUILD_FLAGS, FIXED_ADDRESS, HASH, EXECUTION_ORDER]. "\
"To specify more than one flag, repeat this option on the command line and the default flag set is [PCD, LIBRARY, FLASH, DEPEX, HASH, BUILD_FLAGS, FIXED_ADDRESS]")
help="Specify the specific option to parse EDK UNI file. Must be one of: [-c, -s]. -c is for EDK framework UNI file, and -s is for EDK UEFI UNI file. "\
"This option can also be specified by setting *_*_*_BUILD_FLAGS in [BuildOptions] section of platform DSC. If they are both specified, this value "\
"will override the setting in [BuildOptions] section of platform DSC.")
Parser.add_option("--conf",action="store",type="string",dest="ConfDirectory",help="Specify the customized Conf directory.")
Parser.add_option("--check-usage",action="store_true",dest="CheckUsage",default=False,help="Check usage content of entries listed in INF file.")
Parser.add_option("--ignore-sources",action="store_true",dest="IgnoreSources",default=False,help="Focus to a binary build and ignore all source files")
Parser.add_option("--pcd",action="append",dest="OptionPcd",help="Set PCD value by command line. Format: \"PcdName=Value\"")
Parser.add_option("-l","--cmd-len",action="store",type="int",dest="CommandLength",help="Specify the maximum line length of build command. Default is 4096.")
Parser.add_option("--hash",action="store_true",dest="UseHashCache",default=False,help="Enable hash-based caching during build process.")
Parser.add_option("--binary-destination",action="store",type="string",dest="BinCacheDest",help="Generate a cache of binary files in the specified directory.")
Parser.add_option("--binary-source",action="store",type="string",dest="BinCacheSource",help="Consume a cache of binary files from the specified directory.")
Parser.add_option("--genfds-multi-thread",action="store_true",dest="GenfdsMultiThread",default=True,help="Enable GenFds multi thread to generate ffs file.")
Parser.add_option("--no-genfds-multi-thread",action="store_true",dest="NoGenfdsMultiThread",default=False,help="Disable GenFds multi thread to generate ffs file.")
Parser.add_option("--disable-include-path-check",action="store_true",dest="DisableIncludePathCheck",default=False,help="Disable the include path check for outside of package.")
EccGlobalData.gDb.TblReport.Insert(ERROR_NAMING_CONVENTION_CHECK_VARIABLE_NAME,OtherMsg="The variable name [%s] does not follow the rules"%(Record[1]),BelongsToTable=FileTable,BelongsToItem=Record[0])
help="ARCHS is one of list: IA32, X64, ARM, AARCH64 or EBC, which overrides target.txt's TARGET_ARCH definition. To specify more archs, please repeat this option.")
help="Build the module specified by the INF file name argument.")
Parser.add_option("-b","--buildtarget",type="string",dest="BuildTarget",help="Using the TARGET to build the platform, overriding target.txt's TARGET definition.",
help="Build the platform using multi-threaded compiler. The value overrides target.txt's MAX_CONCURRENT_THREAD_NUMBER. When value is set to 0, tool automatically detect number of "\
"processor threads, set value to 1 means disable multi-thread build, and set value to more than 1 means user specify the threads number to build.")
help="Flags that control the type of build report to generate. Must be one of: [PCD, LIBRARY, FLASH, DEPEX, BUILD_FLAGS, FIXED_ADDRESS, HASH, EXECUTION_ORDER]. "\
"To specify more than one flag, repeat this option on the command line and the default flag set is [PCD, LIBRARY, FLASH, DEPEX, HASH, BUILD_FLAGS, FIXED_ADDRESS]")
help="Specify the specific option to parse EDK UNI file. Must be one of: [-c, -s]. -c is for EDK framework UNI file, and -s is for EDK UEFI UNI file. "\
"This option can also be specified by setting *_*_*_BUILD_FLAGS in [BuildOptions] section of platform DSC. If they are both specified, this value "\
"will override the setting in [BuildOptions] section of platform DSC.")
Parser.add_option("--conf",action="store",type="string",dest="ConfDirectory",help="Specify the customized Conf directory.")
Parser.add_option("--check-usage",action="store_true",dest="CheckUsage",default=False,help="Check usage content of entries listed in INF file.")
Parser.add_option("--ignore-sources",action="store_true",dest="IgnoreSources",default=False,help="Focus to a binary build and ignore all source files")
Parser.add_option("--pcd",action="append",dest="OptionPcd",help="Set PCD value by command line. Format: \"PcdName=Value\"")
Parser.add_option("-l","--cmd-len",action="store",type="int",dest="CommandLength",help="Specify the maximum line length of build command. Default is 4096.")
Parser.add_option("--hash",action="store_true",dest="UseHashCache",default=False,help="Enable hash-based caching during build process.")
Parser.add_option("--binary-destination",action="store",type="string",dest="BinCacheDest",help="Generate a cache of binary files in the specified directory.")
Parser.add_option("--binary-source",action="store",type="string",dest="BinCacheSource",help="Consume a cache of binary files from the specified directory.")
Parser.add_option("--genfds-multi-thread",action="store_true",dest="GenfdsMultiThread",default=True,help="Enable GenFds multi thread to generate ffs file.")
Parser.add_option("--no-genfds-multi-thread",action="store_true",dest="NoGenfdsMultiThread",default=False,help="Disable GenFds multi thread to generate ffs file.")
Parser.add_option("--disable-include-path-check",action="store_true",dest="DisableIncludePathCheck",default=False,help="Disable the include path check for outside of package.")
#string STR_gEfiCryptoPkgTokenSpaceGuid_PcdHashApiLibPolicy_PROMPT #language en-US "HASH algorithm to calculate hash"
#string STR_gEfiCryptoPkgTokenSpaceGuid_PcdHashApiLibPolicy_HELP #language en-US "This PCD indicates the HASH algorithm to calculate hash of data.<BR><BR>\n"
"Based on the value set, the required algorithm is chosen to calculate\n"
"the hash of data.<BR>\n"
"The default hashing algorithm for BaseHashApiLib is set to SHA256.<BR>\n"
"0x00000001 - HASH_ALG_SHA1.<BR>\n"
"0x00000002 - HASH_ALG_SHA256.<BR>\n"
"0x00000004 - HASH_ALG_SHA384.<BR>\n"
"0x00000008 - HASH_ALG_SHA512.<BR>\n"
"0x00000010 - HASH_ALG_SM3.<BR>"
#string STR_gEfiCryptoPkgTokenSpaceGuid_PcdCryptoServiceFamilyEnable_PROMPT #language en-US "Enable/Disable EDK II Crypto Protocol/PPI services"
#string STR_gEfiCryptoPkgTokenSpaceGuid_PcdCryptoServiceFamilyEnable_HELP #language en-US "Enable/Disable the families and individual services produced by the EDK II Crypto Protocols/PPIs. The default is all services disabled. This Structured PCD is associated with PCD_CRYPTO_SERVICE_FAMILY_ENABLE structure that is defined in Include/Pcd/PcdCryptoServiceFamilyEnable.h."
// Module that produces the EDK II Crypto Protocol/PPI using the library
// services from BaseCryptLib and TlsLib.
//
// Copyright (c) 2020, Intel Corporation. All rights reserved.<BR>
//
// SPDX-License-Identifier: BSD-2-Clause-Patent
//
// **/
#string STR_MODULE_ABSTRACT #language en-US "Module that produces the EDK II Crypto Protocol/PPI using the library services from BaseCryptLib and TlsLib"
#string STR_MODULE_DESCRIPTION #language en-US "Module that produces the EDK II Crypto Protocol/PPI using the library services from BaseCryptLib and TlsLib."
HMAC-SHA256 Wrapper Implementation which does not provide real capabilities.
Copyright (c) 2016 - 2017, Intel Corporation. All rights reserved.<BR>
Copyright (c) 2016 - 2020, Intel Corporation. All rights reserved.<BR>
SPDX-License-Identifier: BSD-2-Clause-Patent
**/
#include"InternalCryptLib.h"
/**
Retrieves the size, in bytes, of the context buffer required for HMAC-SHA256 operations.
(NOTE: This API is deprecated.
Use HmacSha256New() / HmacSha256Free() for HMAC-SHA256 Context operations.)
Return zero to indicate this interface is not supported.
@retval 0 This interface is not supported.
**/
UINTN
EFIAPI
HmacSha256GetContextSize(
VOID
)
{
ASSERT(FALSE);
return0;
}
/**
Allocates and initializes one HMAC_CTX context for subsequent HMAC-SHA256 use.
@@ -65,12 +45,12 @@ HmacSha256Free (
}
/**
Initializes user-supplied memory pointed by HmacSha256Context as HMAC-SHA256 context for
subsequent use.
Set user-supplied key for subsequent use. It must be done before any
calling to HmacSha256Update().
Return FALSE to indicate this interface is not supported.
@param[out] HmacSha256Context Pointer to HMAC-SHA256 context being initialized.
@param[out] HmacSha256Context Pointer to HMAC-SHA256 context.
@param[in] Key Pointer to the user-supplied key.
@param[in] KeySize Key size in bytes.
@@ -79,7 +59,7 @@ HmacSha256Free (
**/
BOOLEAN
EFIAPI
HmacSha256Init(
HmacSha256SetKey(
OUTVOID*HmacSha256Context,
INCONSTUINT8*Key,
INUINTNKeySize
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
