The name LEDLOGO comes from schematics. It's the red indicator, embedded
in the dot of the 'i' of the ThinkPad logo on laptop's lid.
In vendor firmware, this led starts fading in-and-out, or, in other
words, pulsing, when laptop is put to S3. It helps to determine whether
the laptop is in S3 just by taking a look at the logo.
As of now, coreboot doesn't do anything with this particular indicator,
it's always in enabled (on) state, which is not very convenient.
This patch fixes it.
Tested on T440p.
Change-Id: I85fb69c8c1bed8635a1b31e9b8385c7036bb46dd
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80437
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nicholas Chin <nic.c3.14@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TCHSCR_RST_L signal was originally being configured to 1 in gpio.c but
this was causing some leakage. Configuring it to 0 initially in
romstage fixes this. Also, make sure that EN_PP3300_TCHSCR is
initialized in romstage as well.
BUG=b:322249892
BRANCH=None
TEST=Make brox boots and touchscreen is still working
Change-Id: I5bf1901a3a40a38237b950abcb758f96aebcc1cf
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80300
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is an existing issue for nissa where wake up from RTC wake is not working during suspend_stress_test.
The phenomenon of the issue is that after pulling out the stylus, can see an interrupt storm occurs, checking through:
"cat /proc/interrupts | grep acpi".
When the counter of interrupt is greater than a certain value, "Disabling IRQ #9" will occur, so RTC wake is not working.
Reference: https://review.coreboot.org/c/coreboot/+/65086
This patch skips the locking for GPP_F15 to allow kernel to
configure it later. The interrupt storm of acpi disappears.
BUG=b:321348117
TEST=1. cat /proc/interrupts | grep acpi
there isn't interrupt storm of acpi when pulling out stylus.
2. The stylus tools panel will pop up when pulling out it.
3. Inserts stylus can wakeup DUT after powerd_dbus_suspend.
4. Passed:
suspend_stress_test -c 2500 --suspend_min=15 --suspend_max=20
Change-Id: Ie143c43e0555d17d8a290f17637b537fba806144
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80316
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Ensure that the SerialIoDevMode config and common_soc_config registers
for each variant are programmed consistently with the devices'
enabled status in that variant's overridetree; remove and disable
extraneous devices as appropriate.
TEST=build/boot several puff variants, verify all components working
as expected, nothing missing from cbmem, lspci, etc.
Change-Id: Ib9d0cf48e405be7c00c553646651fc6f28c4e3f0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80164
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that the puff baseboard uses chipset devicetree references, remove
all references whose value is identical to the chipset devicetree
default or the baseboard default, since they are pointless clutter.
TEST=tested with rest of patch train
Change-Id: Iada32111367fdc964d6126ee43e261c1feb123cf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
This patch selects the DRIVERS_MTK_WIFI and USE_MTCL configs for google/yaviks as
the first platform that provides a country list to the Linux kernel via an
ACPI function (MTCL) in SSDT for MediaTek WiFi chipsets that are capable of
operating on the 6GHz band.
BUG=b:295544553
TEST=Build on similar model (PUJJO) that I have access to and verify the
flag and feature work as intended.
TEST=Add wifi_mtcls.bin blob to cbfs
TEST=Build coreboot for pujjo `emerge-nissa coreboot chromeos-bootimage`
TEST=Verify that MTCL defined in the file is present:
TEST=`acpidump -b`
TEST=`iasl ssdt.dat`
TEST=`less ssdt.dsl`
TEST=Search for MTCL
Change-Id: Iec54fc582d68b443665fceda47187c28f1a9216c
Signed-off-by: David Ruth <druth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80305
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subratabanik@google.com>
In case where PAD_CFG_GPI_INT() is initialized with a pin value
lower to PAD_CFG_GPI_IRQ_WAKE() for same GPIO community
the set_ioapic_used() is only called for the PAD_CFG_GPI_IRQ_WAKE() pin.
Due to this the IRQ associated with PAD_CFG_GPI_INT() is found free by
find_free_unique_irq() during IRQ assignment and assigned to other pins
which causes IRQ conflicts
BUG=b:322984217
BRANCH=None
TEST=Boot test on brox, check if correct IRQ assigned to EC
Change-Id: I8c3d557e888b8d0ceac203f49b702910fba26d6d
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80334
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove hardcoded B:D:F numbers for the first socket and pass the PCI
addresses to be locked within SMM by using the smm_pci_resource_store.
This allows to lock down SMM on all sockets without knowing the actual
bus topology or PCI segment group at compile time where the UBOX devices
reside on.
Tested: SMM is locked on all 4 sockets instead of just one.
Change-Id: Ica694911384005681662d3d7bed354a60bf08911
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80247
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update the I2C configuration to match the usage such that only required
I2C controllers are enabled.
BUG=b:319390850
TEST=Build Brox BIOS image and boot to OS. Ensure that only the required
I2C controllers are enabled.
Change-Id: I9f24beb9ef587163362cc6ded88efb05be1329b9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80303
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Introduce BOARD_AMD_BIRMAN_PHOENIX_OPENSIL which selects the openSIL
based Phoenix SoC code. Since the Phoenix chip.c is different due to
some FSP-specific data structures in there that are guarded in the
openSIL case, a separate devicetree for the openSIL case is added.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I248102e92818b2d395d561a4bf2627f80906b2f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
On Brox, HDA Codec used is ALC256. Add verb table for the same. Also,
add the related device tree changes for HDA related registers.
Realtek High Definition Audio Configuration-
Version : 5.0.3.1
BUG=b:317398558
BRANCH=None
TEST=verified HDA on Brox.
HDA Sound cards detected. Headphone working verified.
Device listed under sysfs as below:
cat /sys/bus/hdaudio/devices/ehdaudio0D0/chip_name
ID 256
cat /sys/bus/hdaudio/devices/ehdaudio0D0/vendor_name
Realtek
Change-Id: I1edd5aee053debe39b34048266703031c088cd00
Signed-off-by: Poornima Tom <poornima.tom@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79723
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Macros can be confusing on their own; hiding commas make things worse.
This can sometimes be downright misleading. A "good" example would be
the code in soc/intel/xeon_sp/spr/chip.c:
CHIP_NAME("Intel SapphireRapids-SP").enable_dev = chip_enable_dev,
This appears as CHIP_NAME() being some struct when in fact these are
defining 2 separate members of the same struct.
It was decided to remove this macro altogether, as it does not do
anything special and incurs a maintenance burden.
Change-Id: Iaed6dfb144bddcf5c43634b0c955c19afce388f0
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80239
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
With Cr50, the GPIO EC_IN_RW is used to determine whether EC is trusted. However, With the switch to Ti50, it is determined by Ti50's boot mode. If the boot mode is TRUSTED_RO, the VB2_CONTEXT_EC_TRUSTED flag will be set in check_boot_mode(). Therefore in the Ti50 case get_ec_is_trusted() can just return 0.
The current code of get_ec_is_trusted() only checks the GPIO, which
causes the EC to be always considered "trusted". Therefore, correct the return value to 0 for TPM_GOOGLE_TI50.
BUG=b:321172119
TEST=emerge-nissa coreboot chromeos-bootimage
TEST=firmware_DevMode passed in FAFT test
Change-Id: I308f8b36411030911c4421d80827fc49ff325a1b
Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp- partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
The current panel voltage measured at mainboard side is 1.79V and the
voltage at panel side is 1.74V. Since the panel requires 1.8V or more,
increase the circuit voltage to 1.9V to meet the panel requirement.
After adjustment mainboard side voltage is 1.89V and panel side is
1.84V.
BUG=b:322080023
TEST=Check ciri vm18 ldo voltage
BRANCH=None
Change-Id: I6d6193d45409f53c0b656890c44ddaef253c5e01
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80198
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As a result of hardware changes on this board, the PHY previously
routed to the PSE GbE 1 is now routed to PSE GbE 0 on the Elkhart Lake
SoC.
This patch changes the device PCI ID in the board's devicetree and
accordingly, the GPIO configuration.
BUG=none
TEST=Boot into Linux and observe whether both PSE GbE 0 and PCH GbE
are working, while PSE GbE 1 remains inactive (not listed by 'ip link')
.
Change-Id: I322371f944d15134e6f48ecd84a4026c2fced27b
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The currently used panel type could work with 500 ms but increasing
the value to 1 second allows to use a wider range of LVDS LCD panels,
as many of them specify the delay of 1 s as minimum.
The patch has already been made for mc_ehl3 and serves the purpose of
standardization.
commit c0221aa980 ("mb/siemens/mc_ehl3/lcd_panel.c: Set LVDS re-power
delay to 1 s")
Change-Id: Ife26ff27b41298ceeed7d9aed0c1ae5553ab5ff8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
This is causing an assertion error on the devices that don't have CNVi
enabled because CNVi is hidden behind a FW_CONFIG flag in the
overridetree now.
BUG=b:319188820
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
make sure we can boot to kernel on device.
Change-Id: Ifcfbc04825d4d4e7f2874a4c52f9c5cf3e657856
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80211
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds APCB blobs to the mainboard directory and it replaces
CB:76445 Also this brings onyx_poc mainboard inline with how APCB are
included in other AMD mainboard: commit 95d05d8301 ("mb/google/zork:
Add and use APCB configuration data"), commit I352f58e0d39 ("mb/google/
skyrim: Add and use APCB configuration data") and commit I1c34528fa0f
("mb/amd/onyx_poc: Add and use APCB configuration data").
BUG=none
TEST=build/boot onyx_poc
Change-Id: I1c34528fa0fd15b847c22c995713078c60ac3873
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80204
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As with other devices with only an external display, the Librem mini/
mini-v2 need a few extra seconds (vs an internal panel) for display init in order for the edk2 boot splash to be visible before the
default boot target is booted.
TEST=build/boot Librem Mini v2 w/edk2 payload, verify splash screen
shown / user has time to enter setup menu.
Change-Id: I9d2d514719a9918ee58cc63969b3adae44ac1632
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Some variants added the generic gfx driver with an LCD device without
specifying the address, which is required for the backlight controls
to be functional under Windows. Add the address value where missing.
Address value used (0x80010400) is same as on other Brya variants which
did properly set it, and is taken from the ACPI 6.5 spec section B.4.2,
_DOD (display output device enumeration), table B-2:
- bit 31 = use the ACPI-defined (vs vendor-defined) bit scheme for bits
15-0
- bit 16 = platform firmware can detect the device
- bit 10 = display type is internal/integrated flat panel (aka LCD)
TEST=build/boot Win11 on google/brya (osiris), verify ACPI backlight
controls functional.
Change-Id: Id24e330cfb7c993d12665a704e1ca78e2e38874f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
There was a mistake in the gpio spreadsheet provided by the HW team
and the GPIO assignments for the EC INT and WAKE signals got switched
from what it was in the schematics. The correct assignments are:
GPP_D0 = EC_PCH_INT_ODL
GPP_D1 = EC_PCH_WAKE_ODL
BUG=b:311450057,b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Will try to boot OS image on device and see if there are any
ec errors.
Change-Id: I02057aeb5d82218dbbe4c939d4feb87a4d3da678
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79886
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
