Add check for NULL HostAddress in AllocateBuffer as required by UEFI
specification.
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Add configuration ExceptionList and IgnoreFiles for package config
files. So users can rely on this to ignore some Ecc issues.
Besides, add submodule path in IgnoreFiles section.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2823
Refer to UEFI spec 2.8, Section 13.3.2, a block device should
be scanned as below order:
1. GPT
2. ISO 9660 (El Torito) (UDF should aslo be here)
3. MBR
4. no partition found
Note: UDF is using the same boot method as CD, so put it in
the same priority with ISO 9660.
This would also solve the issue that ISO image with MBR would
be treat as MBR device instead of CD/DVD. That would make the
behavior of the image boot different:
If the CD/DVD's MBR be handled correctly, it would be enumerated
as a bootable device with MBR path and FAT filesystem. Some Linux
Distributions boot from such path (FAT with MBR path for ISO) would
come into the grub console instead of the installation selection.
With this change, the CD/DVD would always be enumerated with CD path.
And it would always boot to the installation selection.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Gary Lin <glin@suse.com>
Cc: Andrew Fish <afish@apple.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Tested-by: Gary Lin <glin@suse.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1614
Introduces new changes to PeiCore to move the contents of temporary
RAM visible to the PeiCore to permanent memory. This expands on
pre-existing shadowing support in the PeiCore to perform the following
additional actions:
1. Migrate pointers in PPIs installed in PeiCore to the permanent
memory copy of PeiCore.
2. Copy all installed firmware volumes to permanent memory.
3. Relocate and fix up the PEIMs within the firmware volumes.
4. Convert all PPIs into the migrated firmware volume to the corresponding
PPI address in the permanent memory location.
This applies to PPIs and PEI notifications.
5. Convert all status code callbacks in the migrated firmware volume to
the corresponding address in the permanent memory location.
6. Update the FV HOB to the corresponding firmware volume in permanent
memory.
7. Use PcdMigrateTemporaryRamFirmwareVolumes to control if enable the
feature or not. when disable the PCD, the EvacuateTempRam() will
never be called.
The function control flow as below:
PeiCore()
DumpPpiList()
EvacuateTempRam()
ConvertPeiCorePpiPointers()
ConvertPpiPointersFv()
MigratePeimsInFv()
MigratePeim()
PeiGetPe32Data()
LoadAndRelocatePeCoffImageInPlace()
MigrateSecModulesInFv()
ConvertPpiPointersFv()
ConvertStatusCodeCallbacks()
ConvertFvHob()
RemoveFvHobsInTemporaryMemory()
DumpPpiList()
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Debkumar De <debkumar.de@intel.com>
Cc: Harry Han <harry.han@intel.com>
Cc: Catharine West <catharine.west@intel.com>
Signed-off-by: Michael Kubacki <michael.a.kubacki@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1614
The security researcher found that we can get control after NEM disable.
The reason is that the flash content reside in NEM at startup and the
code will get the content from flash directly after disable NEM.
To avoid this vulnerability, the feature will copy the PEIMs from
temporary memory to permanent memory and only execute the code in
permanent memory.
The vulnerability is exist in physical platform and haven't report in
virtual platform, so the virtual can disable the feature currently.
When enable the PcdMigrateTemporaryRamFirmwareVolumes, always shadow
all PEIMs no matter the condition of PcdShadowPeimOnBoot or
PcdShadowPeimOnS3Boot.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Guomin Jiang <guomin.jiang@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
UnicodeStrToAsciiStrS requires that the source string is shorter than
the destination buffer and will ASSERT if this is not true. Switch to
UnicodeStrnToAsciiStrS as there are cases where the source string is
longer than the buffer allocated for the device path.
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2818
For better memory management, re-ordered the DestroyRamDisk and
ReportStatusCode calls inside the EfiBootManagerBoot() function.
This will help to clean the unused memory before reporting the
failure status, so that OEMs can use RSC Listener to launch
custom boot option or application for recovering the failed
hard drive.
This change will help to ensure that the allocated pool of memory
for the failed boot option is freed before executing OEM's RSC
listener callback to handle every boot option failure.
Signed-off-by: KrishnadasX Veliyathuparambil Prakashan <krishnadasx.veliyathuparambil.prakashan@intel.com>
Cc: "Gao, Zhichao" <zhichao.gao@intel.com>
Cc: "Ni, Ray" <ray.ni@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2823
The partition binding driver would run serval times during BDS.
If the partition support MBR, it would pass the first connection
in MBR partition child handler. The second connect for the same
device would return already started which would be treated as
not found. And it would continue to run next partition child
handler check. That is incorrect behavior to do next check if one
of the routine functions is passed. It may cause one device
installed serval partition child handle on it.
So treat the EFI_ALREADY_STARTED as EFI_SUCCESS to avoid incorrect
next partition child handle check.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2823
Refer to
http://manpages.ubuntu.com/manpages/bionic/man8/mkudffs.8.html.
Some Linux ISOs may have the MBR table for compatibility reasons
for Windows. The MBR tale would contain the partition entry with
start LBA0 and whole media size. There are two methods to check
the filesystem in the CD-ROM:
1. MBR partition check (Windows)
2. Whole disk check (MAC OS)
UEFI doesn't have the MBR check for UDF and Eltorito. But it may
pass the MBR check for such table and fail to detect the filesystem
of UDF. Skip the MBR check if the MBR is added for Windows
compatiblity so that the partition driver can continue UDF and
ElTorito check.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2823
PartitionValidMbr function's second parameter should be the
last sector of the device. For MBR partition, the block size is
sector size, i.e. 512 bytes. The original value is media block
last LBA which is counted by the media block size. And media
block size is not always 512 bytes, it may be larger which would
cause the MBR boundary check incorrect. The boundary check is
based on the partition entry start LBA and size of LBA which
are both counted by the sector number (512 bytes).
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2844
Update Reclaim() to return the error status from the reclaim
operation and not the status of SynchronizeRuntimeVariableCache()
that can be EFI_SUCCESS even through the status from reclaim
is an error. Without this change, the return status from
SetVariable() can be EFI_SUCCESS even though the variable was
not actually set. This occurs if the variable store is full
and a Reclaim() is invoked to free up space and even after all
possible space is freed, there is still not enough room for
the variable being set. This condition should return
EFI_OUT_OF_RESOURCES.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2786
In order to support enable/disable report status code through memory
or serial dynamic, change the following PCDs from [PcdsFeatureFlag] to
[PcdsFixedAtBuild, PcdsPatchableInModule, PcdsDynamic, PcdsDynamicEx]:
PcdStatusCodeUseSerial
PcdStatusCodeUseMemory
The original plaforms can use PcdsFixedAtBuild in .dsc files to save size.
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Ming Tan <ming.tan@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2701
Recording to the spec, the reconnect is activated upon exiting of the
formset or the browser. Exiting is by user but form-browser internal
logic. That means the reconnection is only happened when user press
ESC or _EXIT action to exit form.
Driver callback may update HII form dynamically so form-browser needs
to refresh its internal data. It's not exiting formset for user
exactly and they didn't know what happened. So use a flag to record
that and do not reconnect driver if updated by callback.
Signed-off-by: Walon Li <walon.li@hpe.com>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
Its been observed that in MenuManagerMenuApp when user
selects a different BootOption using Up/Down key, the
current Cursor position is not chaning.
Still points to the old BootOption.
This changes first dispalys/redraws the old BootOption
followed by new BootOption. Doing so will make current
cursor pointing to the user selected BootOption.
Signed-off-by: Abdul Lateef Attar <abdul@marvell.com>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
UEFI boot options may exist but have the LOAD_OPTION_ACTIVE flag
cleared. This means that the boot option should not be selected
by default, but it does not mean it should be omitted from the
boot selection presented by the boot manager: for this purpose,
another flag LOAD_OPTION_HIDDEN exists.
Given that the latter flag exists solely for the purpose of omitting
boot options from the boot selection menu, and LOAD_OPTION_XXX flags
can be combined if desired, hiding inactive boot options as well is
a mistake, and violates the intent of paragraph 3.1.3 of the UEFI
specification (revision 2.8 errata A). Let's fix this by dropping
the LOAD_OPTION_ACTIVE check from the code that populates the boot
selection menu.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Leif Lindholm <leif@nuviainc.com>
Reviewed-by: Zhichao Gao <zhichao.gao@intel.com>
Add bitmask to structure which gives a binary-inspectable mechanism to
determine if a capsule contains an authentication section or depex section.
(UEFI 2.8 errata a, mantis 2026)
Signed-off-by: Oleksiy Yakovlev <oleksiyy@ami.com>
Signed-off-by: Wei6 Xu <wei6.xu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
OnigurumaIntrinsics.c is now not used. So the implement of function
'memcpy' is now not., which causes build failure with CLANG9 and
XCODE. I remove OnigurumaIntrinsics.c and move the necessary function
implement to OnigurumaUefiPort.c/h.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
The MM communicate 2 protocol was introduced to factor out the mismatch
between traditional MM, which requires the physical address of the MM
buffer to be passed, and standalone MM, which copies the MM communicate
buffer data into a separate buffer, requiring the virtual address. For
this reason, MM communicate 2 carries both addresses, allowing the
implementation to decide which address it needs.
This hides this implementation detail from the callers of the protocol,
which simply passes both addresses without having to reason about what the
implementation of the protocol actually needs.
Note that the old version of the protocol is retained, in order to support
existing implementations that don't require this flexibility.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Sami Mujawar <sami.mujawar@arm.com>
The device manager UI library creates a UiApp submenu that contains a
list of network devices in the system. The logic that creates this menu
assumes that all handles have been connected to their drivers, but this
is not guaranteed in the general case: due to the way UiApp is constructed,
this logic runs before the UiApp entrypoint is invoked, which is where
ConnectAll() is normally called to ensure that all existing controllers
are connected to their drivers. Moving this call into DeviceManagerUiLib
is not an option, since it is incorporated into UiApp via NULL library
class resolution, and so it may not be included to begin with.
So work around this by doing an explicit additional ConnectAll() before
populating the pages.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Link: https://edk2.groups.io/g/devel/topic/72879609#57075
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
Set the default value of PcdAcpiExposedTableVersions for Aarch64
platforms to 0x20. Previously, the default was set to 0x3E for all
platforms. The new value removes ACPI 1.0b compatability, which forces
the use of XSDT 64-bit pointer, as required by Arm SBBR specification.
This also resolves an error reported by acpiview command, as seen on
the RPi (see https://github.com/pftf/RPi4/issues/25).
Signed-off-by: Samer El-Haj-Mahmoud <samer@elhajmahmoud.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Sami Mujawar <sami.mujawar@arm.com>
Acked-by: Hao A Wu <hao.a.wu@intel.com>
