Instead of just printing the register contents, normalize the contents
of the base and limit registers to actual MMIO addresses and then print
those. This will hopefully avoid some confusion caused by the shifted
addresses.
Output on Mandolin before the patch:
=== Data Fabric MMIO configuration registers ===
Addresses are shifted to the right by 16 bits.
idx control base limit
0 93 fc00 febf
1 93 1000000 ffffffff
2 93 d000 f7ff
3 1093 fed0 fedf
4 90 0 0
5 90 0 0
6 90 0 0
7 90 0 0
Output on Mandolin after the patch:
=== Data Fabric MMIO configuration registers ===
idx control base limit
0 93 fc000000 febfffff
1 93 10000000000 ffffffffffff
2 93 d0000000 f7ffffff
3 1093 fed00000 fedfffff
4 90 0 ffff
5 90 0 ffff
6 90 0 ffff
7 90 0 ffff
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I62eeb88ddac6a7a421fccc8e433523459117976a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
This moves the definition for POST_BOOTBLOCK_CAR from the intel-specific
postcodes into the common postcode list, and uses it for the
cache-as-RAM init as needed.
Because POST_BOOTBLOCK_CAR was set to 0x20 in some spots and 0x21 in
most of the others, the values were consolidated into 0x21. This will
change the value on some platforms.
Any conflicts should get sorted out later in the conversion process.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I8527334e679a23006b77a5645f919aea76dd4926
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
This patch enables PCIe port for WWAN as per mtlrvp schematics
BUG=b:224325352
BRANCH=None
TEST=Build and boot mtlrvp to ChromeOS. Ensure that WWAN module
gets enumerated with cbmem -c.
\_SB.PCI0.RP07: Enable RTD3 for PCI: 00:1c.6 (Intel PCIe Runtime D3)
\_SB.PCI0.RP07: Enable WWAN for PCI: 00:1c.6 (Fibocom FM-350-GL)
Signed-off-by: Harsha B R <harsha.b.r@intel.com>
Change-Id: Ib372db9642a3c7b3a21a112fa0e6e0b4bc88a9ea
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72777
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the LIDS field is only used in the ACPI code and not in the C code
of any mainboard using the Mendocino SoC, remove it form the global NVS
and add an ACPI object for this in the DSDT of the mainboards that use
it in their ACPI code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1ed0407826f579eb14169246b7b14ba677c20e8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since the LIDS field is only used in the ACPI code and not in the C code
of any mainboard using the Cezanne SoC, remove it form the global NVS
and add an ACPI object for this in the DSDT of the mainboards that use
it in their ACPI code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6953da5e0f1966aa3022364d9a9c72ebafc698cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since the LIDS field is only used in the ACPI code and not in the C code
of any mainboard using the Picasso SoC, remove it form the global NVS
and add an ACPI object for this in the DSDT of the mainboards that use
it in their ACPI code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia265f3eebf5e48c185d2e4bf4ef74f8eab7c9606
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since the LIDS field is only used in the ACPI code and not in the C code
of any mainboard using the Stoneyridge SoC, remove it form the global
NVS and add an ACPI object for this in the DSDT of the mainboards that
use it in their ACPI code. Eventually the LIDS object should probably be
moved to the EC's ACPI code, but that's out of scope for this patch.
TEST=google/liara doesn't show ACPI errors in Linux' dmesg
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I778c4189607035b4765c6cb8b2e74030dcf9069f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
This simplifies the code flow of the cpu init. APL can do CPU init after
calling FSP-S, while GLK needs to do that before. This is now reflected
directly in the cpu ops rather than using
CONFIG_SOC_INTEL_COMMON_BLOCK_CPU_MPINIT as a proxy.
Change-Id: I7fd1db72ca98f0a1b8fd03a979308a7c701a8a54
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
By default this limits PCI buses to CONFIG_MMCONF_BUS_NUMBER.
Some platforms have multiple PCI root busses (e.g. xeon_sp), where bus
numbers are limited. This provides a basic check. On some platforms it
looks like programming 0xff to the subordinate bus number confuses and
hangs the hardware.
Change-Id: I0582b156df1a5f76119a3687886c4d58f2d3ad6f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
This patch removes the configuration of GPP_A12 for mtlrvp. Garfield
Peak (WLAN) doesn't use GPP_A12 for WAKE_N. Configuring GPP_A12 pin
prevents system entering G3 (reboots) on issuing shutdown -h now. Hence
configuring GPP_A12 as PAD_NC.
BUG=b:224325352
BRANCH=None
TEST=On issuing 'shutdown -h now' system enters G3
Signed-off-by: Harsha B R <harsha.b.r@intel.com>
Change-Id: I5e46b8afd3e0055440fd3c3db4aa5a9f1d4aa556
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Usha P <usha.p@intel.com>
We don't need flashrom support just for vboot payloads. The current
default (USE_FLASHROM=1) is mostly harmless, especially if libflashrom
is not present (the autodetection in vboot_reference just spits out a
pkg-config error but doesn't actually fail the build), but it's better
to be clear we don't need it.
BUG=b:172225709
TEST=build
Change-Id: I53bcc2d1e7666646ddad58ba3717cfdd321014e8
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72716
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
NVMe PCIe 9-12 using clk_src1 and clk_req2 mapping to hardware design,
Due to inconsistency between PMC firmware and FSP, we need to set
clk_src to clk_req number, not same as hardware mapping in coreboot.
Then swap correct setting to clk_src=1,clk_req=2 in mFIT.
BUG=b:265720813
TEST=build firmware and veirfy suspend function on DUT.
Cq-Depend: chrome-internal:5351299
Change-Id: Ia057dfa98cb9293d9e212edb4e4ac198e94e8985
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72051
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add configuration to bump up the SPI flash bus speed from 66 MHz to 100
MHz starting the board version of the current phase.
BUG=b:260127676
TEST=Build and boot to OS in Frostflow with 100 MHz SPI bus speed.
Observe that the boot time improved by 100 ms compared to 66 MHz SPI
flash bus speed.
firmware log:
SPI fast read speed: 100 MHz
At 66 MHz:
Total Time: 1,563,384
At 100 MHz:
Total Time: 1,462,570
Change-Id: I9435f4ad0d3541b040703dc9a453badbd080dc09
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Fix:
cc1: error: src/vendorcode/amd/pi/00670F00: No such file or directory [-Werror=missing-include-dirs]
cc1: error: src/vendorcode/amd/pi/00670F00/binaryPI: No such file or directory [-Werror=missing-include-dirs]
cc1: error: src/vendorcode/amd/pi/00670F00/Include: No such file or directory [-Werror=missing-include-dirs]
cc1: error: src/vendorcode/amd/pi/00670F00/Proc: No such file or directory [-Werror=missing-include-dirs]
cc1: error: src/vendorcode/amd/pi/00670F00/Proc/Common: No such file or directory [-Werror=missing-include-dirs]
cc1: error: src/vendorcode/amd/pi/00670F00/Proc/CPU: No such file or directory [-Werror=missing-include-dirs]
cc1: error: src/vendorcode/amd/pi/00670F00/Proc/CPU/Family: No such file or directory [-Werror=missing-include-dirs]
cc1: error: src/vendorcode/amd/pi/00670F00/Proc/Fch: No such file or directory [-Werror=missing-include-dirs]
cc1: error: src/vendorcode/amd/pi/00670F00/Proc/Fch/Common: No such file or directory [-Werror=missing-include-dirs]
Change-Id: I745f4fc421c91c413fe0d3155d3494ed9704eeb6
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
The PCI Device ID Assignments table from PPRs #57019 Rev 1.65 and
PPR #57396 Rev 1.54 were used as a reference. Some devices will need to
have ops added in future patches. Since the xhci_2 device isn't there
any more, also drop it from the mainboard devicetrees. The actual USB
port configuration on xhci_0 and xhci_1 is updated in the next patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I49721bc44fa1e2a0118a8c3ac79a36aee64be687
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Now that the PCIe ports on device 1 are added, rename the aliases for
the PCIe ports on device 2 to have a common naming scheme. For phoenix
the device alias names are based on the device and function number the
bridge is connected to.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5f5698408019bb9222b599dd78540ca1b187b56d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72737
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Only the PCIe ports on the functions of device 2 were present in the
devicetree and had the amd_external_pcie_gpp_ops ops assigned. Add the
missing PCIe ports on the functions of device 1 and assign the
amd_external_pcie_gpp_ops ops to them.
This SoC uses a slightly different naming scheme for its PCIe GPP ports.
Previously the PCIe GPP bridge number from the PCI Device ID Assignments
table from the PPR was used. Those bridge numbers are one less than the
function numbers of the device. This is due to function 0 being a dummy
bridge to avoid having to shuffle around the function numbers when the
first bridge is unused, since the PCIe specification mandates the
function 0 to be implemented if any other function on the same device is
implemented. In order for the device aliases to be consistent with the
PCIe device and function numbers which is way more commonly used and
also what lspci shows and what goes into the DXIO descriptors, change
the naming scheme of the aliases.
This was checked with PPR #57019 Rev 1.65 and PPR #57396 Rev 1.54.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib5c62c1df585877d9b6986a462a3636d4f2eb4c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72736
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This enables L1.2 for the SSD port.
link_hotplug is unused on Mendocino, so remove it while I'm here, just
as code cleanup. This has no functional difference.
Enabling L1.2 on other devices currently causes problems. Debug is
ongoing.
BUG=b:265890321
TEST=Build & boot, look at states enabled in lspci. Test device
functionality.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I8940856a127c8a4ba45148cbbf07a08b621beb4d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Commit b171f76812 ("soc/amd/*: Hook up GPP bridges ops to devicetree")
missed adding the amd_external_pcie_gpp_ops ops to the gpp_gfx_bridge
PCIe ports, so add them. Those devices were previously covered by the
PCI_DID_AMD_FAM17H_MODEL60H_PCIE_GPP_D1 PCI device ID in the list that
got removed in the referenced commit.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I55434bf486569b32901b3840193a09cc5955abb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
This allows us to use the same file for PCO, CZN, MDN, PHX, & Glinda.
PCO supports the warm reset, and future chips can support it by setting
the SOC_AMD_SUPPORTS_WARM_RESET option.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib6459e7ab82aacbe57b4c2fc5bbb3759dc5266f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72658
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
