When using the default initial core display clock frequency, Metaknight
has a rare stability issue where the startup of Chrome OS in secure mode
may hang. Slowing the initial core display clock frequency down to
172.8 MHz as per Intel recommendation avoids this problem.
The CdClock=0xff is set in dedede baseboard,and we overwrite it as 0x0
(172.8 MHz) for metaknight.
BUG=None
BRANCH=dedede
TEST=Build firmware and verify on fail DUTs.
Check the DUTs can boot up in secure mode well.
Change-Id: I987277fec2656fe6f10827bc6685d3d04093235e
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Commit b67c5ed [3rdparty/fsp: Update submodule pointer to newest master]
updated the FSP binaries/headers for Comet Lake, which included a change
moving PcieRpHotPlug from FSP-S to FSP-M. Unfortunately the existing
UDP in FSP-S was left in and deprecated, which allowed the change to go
unnoticed until it was discovered that hotplug wasn't working.
Since other related platforms (WHL, CFL) share the SoC code but use
different FSP packages, add the setting of the PcieRpHotPlug UPD to
romstage/FSP-M and guard it with '#if CONFIG(SOC_INTEL_COMETLAKE)'.
Test: build/boot Purism Librem 14, verify WiFi killswitch operates
as expected / WiFi is re-enabled when turning switch to on position.
Change-Id: I4e1c2ea909933ab21921e63ddeb31cefe1ceef13
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch extends `struct pad_config` to add new variable for gpio
lock action.
Additionally, it creates new GPIO PAD configuration macros that perform
GPIO pad configuration and pad lock configuration as well.
List of new macros are:
1. PAD_CFG_NF_LOCK
2. PAD_CFG_GPO_LOCK
3. PAD_CFG_GPI_LOCK
4. PAD_CFG_GPI_TRIG_OWN_LOCK
5. PAD_CFG_GPI_GPIO_DRIVER_LOCK
6. PAD_CFG_GPI_INT_LOCK
7. PAD_CFG_GPI_APIC_LOCK
8. PAD_CFG_GPI_IRQ_WAKE_LOCK
Mainboard users can use the above macros to lock the PAD after
configuration.
So far on IA chipset, the default GPIO pad lock configuration reset
type is POWERGOOD hence, it's recommended as per GPIO BWG (doc: 630603)
to configure the GPP PAD reset type the same as lock configuration
reset type to avoid GPP reset value misconfiguration issue.
BUG=b:211573253, b:211950520
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibf8b0a845005ad545266d995449d0aa711f45a61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This patch performs GPIO PAD lock configuration in non-smm mode.
Typically, coreboot enables SMI at latest boot phase post FSP-S,
hence, FSP-S might get chance to perform GPP lock configuration.
With this code changes, coreboot is able to perform GPIO PAD
lock configuration early in the boot flow, prior to calling FSP-S.
Also, this patch ensures to have two possible options as per GPIO
BWG to lock the GPIO PAD configuration.
1. Using SBI message with opcode 0x13
2. Using Private Configuration Register (PCR)
BUG=b:211573253, b:211950520
TEST=Able to build and boot brya variant with this code change.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I71b4e2f24303b6acb56debd581bd6bc818b6f926
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60801
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For one specific type of APU, it doesn't have HDMI. When we detect
this APU, we need to explicitly disable HDMI in DDI settings,
otherwise the system would freeze.
get_cpu_count() == 4 && get_threads_per_core() == 2: This case is for
2 Core and 4 Thread CPU (2C/4T for short).
get_cpu_count() == 2: This is for 2C/2T. This is for a possible future case.
BUG=b:208677293
Change-Id: I8d0fa96818a768b7960d92821b927dbc622675ae
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
There is no wakeup source when we test function of suspend and resume.
The root cause is that the monitor enable bit of PWRAP is not configured
correctly.
BUG=b:213255218, b:214978483
TEST=receive wakeup source from MT6366 successfully
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I324d18fa5d3cd745c35fcf0f207e1b444b5e898b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61330
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit bd9b044a96 ("mb/system76: rtd3: Remove SrcClk pin
on CPU RP").
Previously, RTD3 expected a PCH index for the root port and did not work
with the CPU PCIe RP present on TGL, so SrcClk pin was disabled.
Set them now that RTD3 supports mapping the index for the CPU RP.
Change-Id: Ia7519b9f5a2be52cd5575615c28d20371a26996b
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Taniks will use two PCIE port signals with one slot, one CLK and one
CLKREQ at next build. In order to accommodate this, probe statements
are added to the devicetree. This only affects NVME SSD and EMMC.
BUG=b:215040000
TEST=Build FSP with debug output enabled, and observe the correct root
ports being initialized depending on the FW_CONFIG values for BOOT_EMMC
and BOOT_NVME.
Cq-Depend:chromium:3397561
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I2ead505088f19fd3bf9768b541838395c82ef051
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The TCO timer is the default watchdog of an x86 host and can reset the
system once it has expired for the second time. There are applications
where this reset is not acceptable while the TCO is used. In these
applications the TCO expire event generates an interrupt and software
takes care. There is a bit in the TCO1_CNT register on Elkhart Lake to
prevent this reset on expiration (called NO_REBOOT, see doc #636722 ).
This bit can either be strapped on hardware or set in this register to
avoid the reset on expiration. While the hardware strap cannot be
overridden in software, the pure software solution is more flexible.
Unfortunately, the location for this bit differs among the different
platforms. This is why it has to be handled on soc level rather than on
TCO common code level.
This commit adds a Kconfig option where NO_REBOOT can be enabled. This
makes it easy to reach this feature over to the mainboard where it can
be selected if needed.
Change-Id: Iaa81bfbe688edd717aa02db86f0a93fecdfcd16b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Prepares compilation for x86_64 by avoiding casts to different sizes.
Current patch fixes:
1.
src/northbridge/intel/i945/raminit.c: In function 'ram_read32':
src/northbridge/intel/i945/raminit.c:77:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
77 | read32((void *)offset);
| ^
2.
src/northbridge/intel/i945/rcven.c: In function 'sample_strobes':
src/northbridge/intel/i945/rcven.c:29:24: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
29 | read32((void *)addr);
| ^
src/northbridge/intel/i945/rcven.c:30:24: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
30 | read32((void *)(addr + 0x80));
| ^
3.
src/northbridge/intel/i945/gma.c: In function 'intel_gma_init_lvds':
src/northbridge/intel/i945/gma.c:98:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
98 | (void *)pgfx, mmiobase, piobase, pphysbase);
| ^
src/northbridge/intel/i945/gma.c:359:25: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
359 | (void *)pgfx, hactive * vactive * 4);
| ^
src/northbridge/intel/i945/gma.c:360:24: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
360 | memset((void *)pgfx, 0x00, hactive * vactive * 4);
| ^
src/northbridge/intel/i945/gma.c: In function 'intel_gma_init_vga':
src/northbridge/intel/i945/gma.c:384:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
384 | (u32)mmiobase, piobase, pphysbase);
|
4.
src/northbridge/intel/i945/northbridge.c: In function 'mch_domain_read_resources':
src/northbridge/intel/i945/northbridge.c:64:23: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
64 | cbmem_topk = ((uint32_t)cbmem_top() / KiB);
| ^
Change-Id: I5ac7a1cb5d85a346114f909047d5a7c21ddb43e9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Chromebooks normally run with non-serial enabled firmware because
writing to the UART console is very slow. This unfortunately makes
debugging boot errors more difficult. We tend to rely on port 80s and/or
the vboot recovery code.
When CONSOLE_CBMEM_DUMP_TO_UART is selected it will dump the entire
cbmem console to the UART whenever `vboot_reboot()` is called. We don't
incur any boot time penalty in the happy path, but still retain the
ability to access the logs when an error occurs.
The previous implementation was using a hard coded UART index and
`get_uart_baudrate` was always returning 0 since `CONFIG_TTYS0_BAUD`
wasn't defined. This change makes it so the UART console properties are
available when CONSOLE_CBMEM_DUMP_TO_UART is set. This results in the
following .config diff:
+CONFIG_UART_FOR_CONSOLE=0
+CONFIG_TTYS0_BASE=0x3f8
+CONFIG_TTYS0_LCS=3
+CONFIG_CONSOLE_SERIAL_115200=y
+CONFIG_TTYS0_BAUD=115200
This functionality is especially helpful on Guybrush. PSP Verstage is
run on S0i3 resume. Today, if there is an error, the cbmem console is
lost since it lives in the PSP SRAM.
BUG=b:213828947, b:215599230
TEST=Build non-serial guybrush FW and verify no serial output happens in
happy path. Inject a vboot error and perform an S0i3 suspend/resume.
Verify CBMEM console gets dumped to the correct UART.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I997942204603362e51876a9ae25e493fe527437b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The FSP API is used to notify the FSP about different phases in the
boot process. The current FSP specification supports three notify
phases:
- Post PCI enumeration
- Ready to Boot
- End of Firmware
This patch attempts to make calling into the FSP Notify Phase APIs
optional by using native coreboot implementations to perform the
required lock down and chipset register configuration prior boot to
payload.
BUG=b:211954778
TEST=Able to build brya without any compilation issue and coreboot
log with this code changes when SKIP_FSP_NOTIFY_PHASE_READY_TO_BOOT
and SKIP_FSP_NOTIFY_PHASE_END_OF_FIRMWARE config enabled.
coreboot skipped calling FSP notify phase: 00000040.
coreboot skipped calling FSP notify phase: 000000f0.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ia95e9ec25ae797f2ac8e1c74145cf21e59867d64
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Since Tiger Lake platform, the HECI1 device can be disabled on
Alder Lake platform using two different mechanism:
A. Using PMC IPC command 0xA9.
B. Sending SBI message under SMM.
In current scope of Alder Lake the default implementation is using
(B) sending sbi message under SMM. A follow up patch to add the
possible options and let platform to choose the applicable one.
List of changes:
1. Drop `HeciEnabled` from dt and dt chip configuration.
2. Replace all logic that disables HECI1 based on the `HeciEnabled`
chip config with `DISABLE_HECI1_AT_PRE_BOOT` config.
3. Default enable HECI1 device in `chipset.cb` to ensure the HECI1
device can undergo the PCI enumeration and later based on the
mainboard policy the HECI1 device can be disabled.
Mainboards that choose to make HECI1 enable during boot don't override
`DISABLE_HECI1_AT_PRE_BOOT` config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie673e634fbc0bdece419c379d417b08dfb4819e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enable PSE GBE with following changes:
1. Configure PCH GBE related FSP UPD flags
2. Add PSE GBE ACPI devices
3. Refactor PCH GBE FSP-S code and merge it together
with PSE GBE code
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: If3807ff5a4578be7b2c67064525fa5099950986a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The Intel® Programmable Services Engine (Intel® PSE) is a
dedicated offload engine for IoT functions powered by an ARM
Cortex-M7 microcontroller. It provides independent, low-DMIPS
computing and low-speed I/Os for IoT applications, plus
dedicated services for real-time computing and time-sensitive
synchronization.
The PSE hosts new functions, including remote out-of-band
device management, network proxy, embedded controller lite
and sensor hub.
This CL enables the user to provide the base address of the
PSE FW blob which will then be loaded by the FSP-S onto the
ARM controller. PSE FW will do the initialization work of
PSE controller and its peripherals. The loading of PSE FW
should have negligible impact on boot time unless PSE
controller could not locate the PSE FW and FSP will attempt to
redo PSE FW loading and wait for PSE handshake until it times
out. Once PSE controller locate the PSE FW, it will do
initialization concurrently by itself with coreboot booting.
It also adds PSE related FSP-S UPD settings which enable the
setup of peripheral ownership (assigned to the PSE or x86
subsystem) and interrupts. These assignments need to take
place at a given point in the boot process and cannot be
changed later.
To verify if PSE FW is loaded properly, the user could enable
PchPseShellEnabled flag and the log will be printed at PSE UART
2.
For further info please refer to doc #611825 (for HW overview)
and #614110 (for PSE EDS).
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ifea08fb82fea18ef66bab04b3ce378e79a0afbf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Constructed out of a mix of autoport results, p8z77-m_pro, and
tool dumps.
Working:
- Core i7-3770K CPU
- SeaBIOS 1.13.0 boot to Linux 5.4.24 and Windows 10 1903
(all further tests are under these versions)
- USB2 / USB3
- SATA
- Gigabit ethernet
- CPU temp sensors (memtest86+ 5.0.1)
- Hardware monitoring under Linux
- Native and MRC raminit
- PCIe GPU in both "PCIEX16" slots (16x/4x, nVidia Quadro 600)
- Integrated graphics with Intel OpROM and libgfxinit (all ports)
- Serial port
- Windows with libgfxinit framebuffer
- 2ch sound playback, Linux and Windows
Not working:
- PS/2 mouse
- 6ch analog audio out
- PCI POST card in PCI slot
Untested:
- PS/2 keyboard
- Internal USB3 ports
- Digital audio out
Change-Id: If756e791ddce747cb1706414be8e41e83f88922b
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
