Since these boards will use S0ix they need to leave CSME enabled for the
CPU to reach C10.
Change-Id: I70c908402c9964508bb9c439d48d24773f5a35ab
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The newer batch of these boards do not de-assert VW PLTRST# on S3
resume, causes the units to not power on in the EC code. Switch them to
S0ix by default, but leave S3 available.
Change-Id: I95337c1391102db9e020e82bdd938659c1a4f905
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Apply CB:75284 to Meteor Lake.
CB:52731 introduced support for reading SPD from the EEPROM via SMBus.
Replace the now unneeded workaround for DDR5 with filling in the correct
channels for DDR5.
Change-Id: I600d8fd480cb84d5dcb679e4f0bdeeaaebfab386
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
CB:52731 introduced support for reading SPD from the EEPROM via SMBus.
Replace the now unneeded workaround for DDR5 with filling in the correct
channels for DDR5.
Change-Id: I5a92199a7cd2718e9396f0dac8257df40e4f834c
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
DDR5 uses a Serial Presence Detect (SPD) with hub function
(SPD5 hub device) to store the SPD data. The SPD5 hub has 1024 bytes of
EEPROM (`CONFIG_DIMM_SPD_SIZE=1024`).
Change-Id: Ic5e6c58f255bef86b68ce90a4f853bf4e7c7ccfe
Co-authored-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Sending the disable and EOP commands will not work if flash descriptor
override is set on Meteor Lake.
Change-Id: I3b5a56229434c9cc326141d48359faa7759541ee
Signed-off-by: Jeremy Soller <Jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Add function needed to generate ACPI backlight control SSDT, along with
Kconfig values for accessing the registers.
Change-Id: Ied08e5e9fe4913bd60474ed7dcf88b945172558d
Signed-off-by: Jeremy Soller <jeremy@sysetm76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Intel introduced a new UPD specifically for setting the HDA subsystem ID
in FSP-M. Using SiSsidTablePtr in FSP-S no longer works as it will be
locked with a default value of 0 by that point.
Change-Id: I5e668747d99b955b0a3946524c5918d328b8e1d3
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The ACPI is adjusted based on SOFTWARE_CONNECTION_MANAGER, so set
the UPD to match this to avoid the connection type being
mismatched.
If it's mismatched, the TBT port will timeout.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I3ab68c01f682723dab39870f0676e59ae3d89add
The Lemur Pro 13 (lemp13) is an Intel Meteor Lake-U based board.
There are 2 variants to differentiate which keyboard design the unit
uses, as they require different EC firmware.
Change-Id: Icac8c7dafd6371881622d797f399f8ddbe13cbce
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The Darter Pro 10 (darp10) is an Intel Meteor Lake-H based board.
There are 2 variants in order to differentiate the 14" and 16" models,
as they have different keyboards and so have different EC firmware.
Change-Id: Iaef03a47cf108591ef823bfa779777c7c05c6337
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The Bonobo has 2 AMPs: one for the speakers and one for the subwoofer.
Smart AMP data was collected using a logic analyzer connected to the IC
during system start on proprietary firmware. This data is then used to
generate a C file [1].
[1]: https://github.com/system76/smart-amp
Change-Id: I5389a9890563ebd3adb20096b6225f474bc006f9
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Add a driver for laptops with NVIDIA Optimus (hybrid) graphics. The
driver provides ACPI support for dynamically powering on and off the
GPU, NVIDIA Dynamic Boost support, and a function for enabling the GPU
power in romstage.
References:
- DG-09845-001: NVIDIA GN20/QN20 Hardware Design Guide
- DG-09954-001: NVIDIA GN20/QN20 Software Design Guide
Change-Id: I2dec7aa2c8db7994f78a7cc1220502676e248465
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The HX boards, using PCH-S, use a discrete Thunderbolt device (Intel
Maple Ridge), as opposed to a built-in one like the boards using PCH-P.
Fixes Thunderbolt on RPL-HX boards using the Maple Ridge controller.
Change-Id: I53d18f3ec5a084431e1113782c791bcb42728350
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Add a new driver for discrete Thunderbolt controllers. This allows using
e.g. Maple Ridge devices on Raptor Point PCH.
Ref: Titan Ridge BIOS Implementation Guide v1.4
Ref: Maple Ridge BIOS Implementation Guide v1.6 (#632472)
Change-Id: Ib78ce43740956fa2c93b9ebddb0eeb319dcc0364
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The Infineon SLB 9672 on newer Clevo machines regularly fails TPM Resume
on S3 with the error `TPM_RC_VALUE`.
Per TPM2 spec, handle the failure by performing a TPM Restart.
> The startup behavior defined by this specification is different than
> TPM 1.2 with respect to Startup(STATE). A TPM 1.2 device will enter
> Failure Mode if no state is available when the TPM receives
> Startup(STATE). This is not the case in this specification. It is up
> to the CRTM to take corrective action if it the TPM returns
> TPM_RC_VALUE in response to Startup(STATE).
Fixes the following error from being repeatedly logged in Linux:
> kernel: tpm tpm0: A TPM error (256) occurred attempting get random
Ref: Trusted Platform Module Library, Part 1: Architecture, rev 1.59
Change-Id: I3388007d4448c93bd0dda591c8ca7d1a8dc5306b
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The Razer Blade Stealth Kaby Lake has 2 variants. One is the H2U
variant, as originally committed, with the SKU number RZ09-01962, also
known as the 2016 model, and the H3Q model with SKU numbers RZ09-01963
and RZ09-01964, known as the Mid 2017 model. This commit adds support
for the H3Q model. With respect to coreboot, there are few known
differences:
1. Only the H2U has TPM.
2. The USB ports are different.
3. The screen size (and therefore VBIOS Table) is different.
4. The hda_verb is very slightly different.
5. The gpio is different.
Change-Id: I493a651e52c2eb938daa67a05e9caaa784020fa4
Signed-off-by: Reagan Bohan <xbjfk.github@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Apply commit c6b65c1a81 ("soc/intel/alderlake: Enable USB2 port reset
message on Type-C ports") to Meteor Lake.
This change is added to address the issue of USB3 ports downgrading to
high speed during low power modes and not returning back to super speed.
The patch enables port reset event on USB2 ports. This event is
is passed to USB3 upstream ports to upgrade back to super speed (USB3)
after a downgrade during low power state.
Change-Id: Iac702a8d8edd2b3b7e03abcac020be7e45335821
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82730
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
linux_trampoline.c generation is broken with latest crossgcc-i386
toolchain. Fix the issue to enable the building.
../cbfstool/linux_trampoline.S: Assembler messages:
../cbfstool/linux_trampoline.S💯 Error: no instruction mnemonic
suffix given and no register operands; can't size
instruction
<builtin>: recipe for target '../cbfstool/linux_trampoline.o'
failed
TEST=Build and boot on intel/archercity CRB
cd util/cbfstool/
rm linux_trampoline.c
make linux_trampoline.c
Change-Id: I7faca296f946bb4e9fd510661357925e5dcf9a6b
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82704
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The comment that the PchHdaAudioLink UPDs only configure GPIOs is
incorrect. Setting this to 1 is needed to enable HDA audio link.
Same exact situation as with Alder Lake in CL 71715.
Change-Id: Iecbe106ae18b5a8b53c04a5335a4e4c4ae27c7a0
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Initial commit is a copy of ec/system76/ec from tag v24.02.1 (commit
0a280ff7) with string changes. Dasharo-specific features will be added
in subsequent commits, similar to how Librem EC support was added in
changes 52390 and 52391.
Change-Id: Ic7c3d9413488026548514963eb78accc28e41e06
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
coreboot needs to figure out top of memory to place CBMEM data. On some
non-x86 QEMU virtual machines, this is achieved by probing the RAM space
to find where the VM starts discarding data since it's not backed by
actual RAM. This behaviour seems to have changed on the QEMU side since
then, VMs using the "virt" model have started raising exceptions/errors
instead of silently discarding data (likely [1] for example) which has
previously broken coreboot on these emulation boards.
The qemu-aarch64 and qemu-riscv mainboards are intended for the "virt"
models and had this issue, which were mostly fixed by using exception
handlers in the RAM detection process [2][3]. But on 32-bit RISC-V we
fail to initialize CBMEM if we have 2048 MiB or more of RAM, and on
64-bit RISC-V we had to limit probing to 16383 MiB because it can run
into MMIO regions otherwise.
The qemu-armv7 mainboard code is intended for the "vexpress-a9" model VM
which doesn't appear to suffer from this issue. Still, the issue can be
observed on the ARMv7 "virt" model via a port based on qemu-aarch64.
QEMU docs for ARM and RISC-V "virt" models [4][5] recommend reading the
device tree blob it provides for device information (incl. RAM size).
Implement functions that parse the device tree blob to find described
memory regions and calculate the top of memory in order to use it in
mainboard code as an alternative to probing RAM space. ARM64 code
initializes CBMEM in romstage where malloc isn't available, so take care
to do parsing without unflattening the blob and make the code available
in romstage as well.
[1] https://lore.kernel.org/qemu-devel/1504626814-23124-1-git-send-email-peter.maydell@linaro.org/T/#u
[2] https://review.coreboot.org/c/coreboot/+/34774
[3] https://review.coreboot.org/c/coreboot/+/36486
[4] https://qemu-project.gitlab.io/qemu/system/arm/virt.html
[5] https://qemu-project.gitlab.io/qemu/system/riscv/virt.html
Change-Id: I8bef09bc1bc4e324ebeaa37f78d67d3aa315f52c
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80322
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The crashlog code in intel/common/block and meteorlake soc
was casting integer addresses directly to pointer types,
which caused compilation errors in x86_64 bit builds.
This commit fixes the issue by using uintptr_t for casting
integer addresses to pointer types before dereferencing.
BUG=b:329034258
TEST=Successfully build Meteor Lake (rex) in both x86_32 and
x86_64 modes.
Change-Id: I2d0814a8b767270ec140341bfb51d0782469545d
Signed-off-by: Appukuttan V K <appukuttan.vk@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82481
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
For multi-SKU/SoC supports, IIO domain layouts are returned from FSP
HOBs. Add _OSC ASL generation utils so that static IIO domain layout
definition file per SKU/SoC are not needed any more.
The _OSC generation codes is a thin AML generation layer which
further invokes \_SB.POSC which is defined in ASL. The ASL handler
is able to handle boot-time generated info as parameters while keeps
good readability for the ease of maintenance. In this case, firmware
granted capabilities are calculated in boot time and passed to ASL
handler as parameters.
TEST=Build and boot on intel/archercity CRB
Change-Id: Ibd3bfa2428725fe593754436d5ed75a3a11b4cdc
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
This commit removes config guard around FSPM_ARCH_UPD from the
FspApi.h header file. This change is done to ensure
that this header file can be used with both x86_32 and x86_64
architectures and also with different FSP specification versions.
The following modifications are made:
- Removes PLATFORM_USES_FSP2_X86_32 config guard around
FSPM_ARCH_UPD, this was added to isolate the structure from
x64 build. This is not really required since the x64 build uses
FSP2.4 structures.
BUG=b:343428206
TEST=Verified x86_32 and x86_64 builds on Meteor Lake board (Rex)
Change-Id: Idc849de73723036323f81dfd055730f6669cd52e
Signed-off-by: Appukuttan V K <appukuttan.vk@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82425
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
EnableMultiPhaseSiliconInit upd is deprecated and has been
removed starting with v2.4 of FSP specification. Multi-phase
silicon initialization is mandatory for all FSP implementations
compliant to v2.4.
The following modifications are made:
- In fsp_params.c and silicon_init.c EnableMultiPhaseSiliconInit
update is guarded so that it will get included only if FSP2.4
is not selected.
BUG=b:329034258
TEST=Verified x86_32 and x86_64 builds on Meteor Lake board (Rex)
Change-Id: Icdbf3bacc0a05975fc941b264fd400d74f506fce
Signed-off-by: Appukuttan V K <appukuttan.vk@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
* Conditionally select FSP 2.4 when x86_64 support is available
(HAVE_X86_64_SUPPORT).
* Default to FSP 2.3 otherwise.
* Adjust default FSP header path to align with architecture.
BUG=b:242829490
TEST=Able to build google/rex in both 32-bit and 64-bit mode.
Change-Id: Ib77a34c6bf7bca3485a197f109d1550ac3d51cc0
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
This change allows eSOL to be enabled on production Meteor Lake silicon
even when 64-bit support is not present. eSOL support is still TBD for
64-bit FSP hence, skip adding this support for 64-bit build.
TEST=Able to build and boot google/rex64 w/o eSOL.
Change-Id: I16762e5b74ae0aaa3c28730479a1fd9defc4d93c
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82716
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit introduces new header files of V3471.91 for the x86_64
architecture in the fsp2_0/meteorlake directory. FSP2.4 brings FSP
64-bits support and the soc Kconfig file has been updated to select
this new header path when FSP2.4 is in use.
BUG=b:329034258
TEST=Verified x86_32 and x86_64 builds on Meteor Lake board (Rex)
Change-Id: Ib41b57e794311db729ac65a968f562aa127e86c3
Signed-off-by: Appukuttan V K <appukuttan.vk@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82473
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
This commit moves FSP V3471.91 header files for Meteor Lake
into a new x86_32 directory to better organize the files based
on the architecture. The Kconfig file has been modified accordingly
to reflect the new paths of the relocated headers.
BUG=b:329034258
TEST=Verified x86_32 and x86_64 builds on Meteor Lake board (Rex)
Change-Id: Id30186a8b1b5a9082f498e18a3378f5e9907b668
Signed-off-by: Appukuttan V K <appukuttan.vk@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82424
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
This commit updates the type definitions for FSP parameters in the
Meteor Lake platform to ensure compatibility with the FSP2.4
specification, that supports 64-bit builds for the first time and
this also ensures that parameter types works for both 32-bit
and 64-bit builds.
- In fsp_params.c, FSPS_ARCH_UPD macro is changed to
FSPS_ARCHx_UPD which supports FSP2.4 and older specifications.
Special handling is added for FspEventHandler assignment to handle
as the variable type is different in both cases.
- In meminit.c, the type for SPD pointers is changed from uint32_t
to efi_uintn_t to support both 32-bit and 64-bit builds.
BUG=b:329034258
TEST=Verified x86_32 and x86_64 builds on Meteor Lake board (Rex)
Change-Id: Ide220f60184135a6488f4472f69a471e2b383e2a
Signed-off-by: Appukuttan V K <appukuttan.vk@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82177
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since this mainboard no longer uses the FSP GOP driver, the DDI port
settings are no longer necessary. The GOP driver was used in the initial
phase of development where we used Tianocore as payload for some test
cases. Finally, this mainboard uses a self-made Linux payload, which
does the graphic initialization.
BUG=none
TEST=Boot into Linux and check if graphic works correctly
Change-Id: Ie9e135fbc2627546d6ef95d7d5ff3e9a9222b5d2
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82663
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Some drives block the CPU from reaching C10 during S0ix suspend without
the RTD3 configs.
Fixes suspend with the following drives:
- Kingston KC3000 (SKC3000D/4096G)
- Kingston HyperX (SHPM2280P2H/240G)
- Solidigm P44 Pro (SSDPFKKW010X7)
The following drives continue to work:
- Samsung 970 Evo (MZVLB250HAHQ)
- WD Black SN770 (WDS250G3X0E)
- WD Green SN350 (WDS240G2G0C-00AJM0)
- WD Blue SN570 (WDS100T3B0C)
Change-Id: Ia369727d0f1aa5ff546cfb5700a63063730e8248
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Tested-by: Levi Portenier <levi@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Code dealing with PAE can be used outside of memset_pae(). This change
extracts creation of identity mapped pagetables to init_pae_pagetables()
and mapping of single 2 MiB map to pae_map_2M_page(). Both functions are
exported in include/cpu/x86/pae.h to allow use outside of pgtbl.c.
MEMSET_PAE_* macros were renamed to PAE_* since they no longer apply
only to memset_pae().
Change-Id: I8aa80eb246ff0e77e1f51d71933d3d00ab75aaeb
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82249
Reviewed-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
<stdio.h> header is used for input/output operations (such as printf,
scanf, fopen, etc.). Although some input/output functions can manipulate
strings, they do not need to directly include <string.h> because they
are declared independently.
Change-Id: Ibe2a4ff6f68843a6d99cfdfe182cf2dd922802aa
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82665
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GCC-14 documentation says "The first argument to calloc is documented to
be number of elements in array, while the second argument is size of
each element, so calloc(n, sizeof (int)) is preferred over
calloc(sizeof(int), n)."
Change-Id: I77b6f4d2eda487b087ba5665b588999633c33e8d
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82658
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 4c7e97b26a ("Update fsp submodule to upstream master branch")
included an update to the VBT from 240 to 250, breaking parsing of
existing VBTs.
After that commit, the VBT was parsed as (from gaze16-3060-b):
[DEBUG] PCI: 00:02.0 init
[INFO ] GMA: Found VBT in CBFS
[INFO ] GMA: Found valid VBT in CBFS
[INFO ] framebuffer_info: bytes_per_line: 4096, bits_per_pixel: 32
[INFO ] x_res x y_res: 1024 x 768, size: 3145728 at 0xd0000000
[DEBUG] PCI: 00:02.0 init finished in 6 msecs
When the expected output is:
[DEBUG] PCI: 00:00:02.0 init
[INFO ] GMA: Found VBT in CBFS
[INFO ] GMA: Found valid VBT in CBFS
[INFO ] framebuffer_info: bytes_per_line: 7680, bits_per_pixel: 32
[INFO ] x_res x y_res: 1920 x 1080, size: 8294400 at 0xd0000000
[DEBUG] PCI: 00:00:02.0 init finished in 6 msecs
Generate blobs for the new version using Intel Display Configuration
Tool (DisCon) v3.3, based on the existing 237 and 240 VBTs.
(For our edk2 payload, the UEFI GOP driver was updated to 17.0.1077.)
Tested on all affected systems:
- darp7
- galp5
- gaze16-3050
- gaze16-3060
- gaze16-3060-b
- lemp10
- oryp8
Tested:
- Boot splash displays on screen again
- Firmware setup menu is rendered, at correct resolution
Change-Id: I918356d9f660b985ee4408ef77544fbd071ab35f
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Tested-by: Daniel Sutton <daniel@system76.com>
Tested-by: Jacob Kauffmann <jacob@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
This patch marks unused USB ports (USB2.0/TCSS) empty to avoid
prompting wrong dmesg as below.
```
usb usb2-port3: Cannot enable. Maybe the USB cable is bad?
```
Trulo variants to override the USB ports as per the target
board design.
TEST=Able to build google/trulo.
Change-Id: I6240e66ed3d1a7198c1a526fdca2483910157235
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Add a new proximity type to represent the sub-NUMA cluster (SNC).
This patch adds necessary Xeon-SP common code level support for
SNC support. When SNC on, each SNC cluster will have a proximity
domain. DIMMs and CPU cores are attached to SNC proximity domains
instead of the processor proximity domains.
With SNC, there are 3 types of proximity domains,
PD_TYPE_PROCESSOR, PD_TYPE_GENERIC_INITIATOR and PD_TYPE_CLUSTER.
proximity domain type checks in Xeon-SP codes are updated to
correctly handle the adding of the new type.
This patch doesn't actually enable SNC. To fully enable SNC, SoC
codes need to override soc_get_cluster_count(), soc_set_cpu_node_
id() and memory_to_pd(), and call soc_set_cpu_node_id() in its
per-CPU init routine.
Change-Id: I32558983780f302ff4893901540a90baebf47add
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Co-authored-by: Ziang Wang <ziang.wang@intel.com>
Co-authored-by: Gang Chen <gang.c.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
IO resource creation utils taking 'from' and 'to' as parameters
use uint16_t for them, where 'to' equals the resource limit plus
1. When a resource is with a limit of 0xFFFF, the value of 'to'
will be clipped to 0x0000 by uint16_t. Fix this problem by use
uint32_t and checks the effective range to make sure it no larger
than UINT16_MAX + 1.
TEST=Build and boot on intel/archercity CRB
TEST=Build on intel/avenuecity CRB
Change-Id: Ie83045683094d6330c1676809f83acf30175cc90
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82192
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
It might be benefical to have utils for domain resource window
creation so that the correct IORESOURCE flags used could be
guaranteed.
TEST=Build and boot on intel/archercity CRB
TEST=Build on intel/avenuecity CRB
Change-Id: I1e90512a48ab002a1c1d5031585ddadaac63673e
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
<stdarg.h> header is used to define macros for handling variable
argument lists in functions like printf. It does not depend on the string
or memory manipulation functions provided by <string.h>.
So let follow conventions and include only the necessary headers in each
header file.
Change-Id: I07ffc65b7feefb8ec4ab8dd268113f9ed8d24685
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82664
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both acpi_create_madt_sci_override and acpi_sci_int have special
handling for the ACPI_NO_PCAT_8259 case, but those cases weren't exactly
obvious, so add a comment with the reason for that.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia6dcf59d5ab9226c61e9c4af95a73a07771b71d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82643
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
AOOSTAR R1 is a Chinese NAS based on Intel N100 (Alder Lake N), with
two 3.5" HDD slots, an M.2 NVMe 2280 SSD slot and a single DDR4-3200
SODIMM slot up to 32GB. It also comes with 2x 2.5Gb Intel NICs,
Intel AX200 WiFi + BT and USB-C Alt-DP Power Delivery.
Working:
- DDR4 RAM (tested with Crucial 16GB 3200MHz CL22)
- Automatic FAN control (IT8613E Super I/O)
- M.2 NVME slot
- 2x SATA ports (Issue on 3.5" HDD, see below)
- USB 2.0 ports
- USB 3.0 ports
- USB-C port with Alt-DP and PD
- HDMI / DisplayPort ports
- 2x 2.5Gb NICs
- WiFi + BT
- MicroSD card reader
- ASPM (Unavailable on stock)
- Linux (Arch Linux, kernel 6.8.7-arch1-1) UEFI booting with EDK2
- Windows 10 UEFI booting with EDK2
Broken:
- Power button (OFF->ON broken, ON->OFF works)
- 3.5" SATA HDDs (Detected only after reboot)
Untested:
- Internal audio
- S3
My motivation for doing this port is enabling ASPM, as it makes a
great difference on idle power consumption (from 8.4W to 5W measured
from the wall).
The last remaining annoyance of this port is the power button not
working. I spent a few hours double checking the Super I/O registers but
then I gave up. A workaround for this is to use the "ON after power
loss" feature and reconnect the power cord to turn on the board.
It's not a big problem for a NAS that will stay ON 24/7.
Any hint on the power button or 3.5" HDD issue is welcome.
VBT extracted from vendor UEFI firmware version 1AXFE 0.01 x64
(Build date and time 11/29/2023 10:57:44)
Compiled with FSP GOP video initialization, using IFD descriptor
and ME blob extracted from vendor UEFI firmware (see above).
The board can be flashed externally using a 1.8V adapter, I used a
CH341a modded for 3.3V I/O. Internal flashing works, as flash is
not read/write protected.
Patchset 5: Re-enabled dptf, added default options to Kconfig.
Patchset 7: Configured USB port mapping and overcurrent, USB3.0 works
Patchset 8: Fixed microSD card reader
Patchset 13: Change Super I/O Fan configuration to reduce fan noise
Change-Id: I9414eb742b6b90459e010b038c1994537e9801a5
Signed-off-by: Federico Amedeo Izzo <federico@izzo.pro>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82010
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adjust setting as recommended by power team.
Add ramstage.c in Makefile.inc to set psys_pl2_watts in
variant_devtree_update().
Also copy CPU power limit values from ovis baseboard.
BUG=b:320410462
BRANCH=firmware-rex-15709.B
TEST=FSP debug emerge-ovis coreboot intelfsp
check overrides setting
[INFO] CPU PsysPL2 = 178 Watts
[INFO] Overriding PsysPL2 (178)
[INFO] Overriding power limits PL1 (mW) (19000,28000) PL2 (mW)
(64000, 64000) PL4 (W) (120)
Change-Id: I9ce3a8f843a87e81d404778aaf250b876b6801eb
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
The code used to reserve MEMSET_PAE_PGTL_SIZE (20 KiB) for page used
for clearing the memory above 4 GiB that was assumed to be 2 MiB page.
memset_pae() checks only the alignment and not the size of this region,
so no error was reported by it.
In most cases this reserved memory in 2-4 MiB range, and because this
range isn't usually used by coreboot (architectural stuff is located in
lower 1 MiB, coreboot tables and ramstage are close to TOLUM and payload
isn't yet loaded when the broken code is executed), it never caused any
problems.
Change MEMSET_PAE_PGTL_SIZE to MEMSET_PAE_VMEM_SIZE and fix wrong macro
definition to reserve properly sized region.
Change-Id: I0df15b0d1767196fe70be14d94428ccdf8dbd5d3
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This patch introduces x86_64 (64-bit) support to the payload, building
upon the existing x86 (32-bit) architecture. Files necessary for 64-bit
compilation are now guarded by the `CONFIG_LP_ARCH_X86_64` Kconfig
option.
BUG=b:242829490
TEST=Able to verify all valid combinations between coreboot and
payload with this patch.
Payload Entry Point Behavior with below code.
+----------------+--------------------+----------------------------+
| LP_ARCH_X86_64 | Payload Entry Mode | Description |
+----------------+--------------------+----------------------------+
| No | 32-bit | Direct protected mode init |
+----------------+--------------------+----------------------------+
| Yes | 32-bit | Protected to long mode |
+----------------+--------------------+----------------------------+
| Yes | 64-bit | Long mode initialization |
+----------------+--------------------+----------------------------+
Change-Id: I69fda47bedf1a14807b1515c4aed6e3a1d5b8585
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81968
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
get_cxl_mode() is the interface for CXL mode config check used by
SoC codes. It could be implemented by mechanisms outside of the
SoC codes, e.g. board codes or OCP VPD driver.
Move the interface declaration out of soc/util.h to a dedicated
header, a.k.a., soc/config.h, so that the implementation codes do
not need to include soc/util.h where there are lots of irrelevant
definitions. Future SoC config check interfaces could be added
to soc/config.h as well.
The default weak implementation is moved out of util.c to
config.c as well.
TEST=Build and boot on intel/archercity CRB
Change-Id: Ia0302b0d3fd93c49e1d6f64e8159f59d50f33e20
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82293
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
While the SoC-level defaults for VGA_BIOS_ID are the expected correctly
remapped PCI VID/PID of the GPU which matches the PCI VID/DID inside the
VBIOS file, some mainboards override the VGA_BIOS_ID setting to the
non-remapped PCI ID. This resulted in coreboot not finding the VBIOS
file after commit 42f0396a10 ("device/pci_rom: rework PCI ID remapping
in pci_rom_probe"). The proper solution would be to not override this
SoC-level config in neither the mainboard code nor some external config
file. This however requires adding/using some mechanism to tell SeaBIOS
which VBIOS image to use for the GPU device. Once this is implemented,
the SoC default for VGA_BIOS_ID shouldn't be overridden any more and
this patch can be reverted again.
This sort-of reverts parts of commit 42f0396a10 ("device/pci_rom:
rework PCI ID remapping in pci_rom_probe"), but it still tries to find
the VBIOS image with the expected remapped PCI ID and only adds trying
the non-remapped PCI ID as a fallback when the file with the remapped
PCI ID doesn't exist and prints a notice in that case. Before the patch
referenced above, using the correct remapped PCI VID/DID resulted in a
warning about the CBFS file with the non-remapped name not being found,
but first checking the remapped version solves that problem.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7cd8e2036250f4ca2239b04cd070bbf0778b13aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
The pre-release notes never capture everything, so we need to do an
update to finalize them after the release is tagged.
This captures on additional SoC added right before the release and
updates the statistics.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id3efcd15597e4fee0bdbca76e474974ae32d3263
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82613
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Integrate head.S directly into libc and remove all instances of head.o.
* Drop 'separate class' entry for head.S.
* Drop special treament for head.o inside lpgcc.
* Change the .text in `x86/head.S` to `.section .text._entry`.
* Drop arch/mock/head.c, initially added as a dummy file.
Change-Id: I156d781908fcc38d455bbf9f2c29e5ab95c7775a
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This moves the multiboot header into its own include file, simplifying
head.S and making it easier to include/exclude the multiboot header
based on config options.
BUG=b:242829490
TEST=Able to build and boot google/rex.
Change-Id: I59a22dfe36044b4dd64a5b028a134be7a7d02a48
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82533
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch tries to simplify the baseboard/variant GPIO programming
for Google/Trulo. The idea is to let each variant maintain
its own complete GPIO PAD configuration table instead of having a
back-and-forth call between baseboard and variants.
With this patch coreboot performing GPIO programming is now much
simpler where the common code block calls into respective variants
and gets the gpio table prior to the pad configuration.
BUG=b:334826281 ([TWL] Decouple GPIO from baseboard to variant)
TEST=Able to build google/orisa.
Change-Id: I4ab88ac094a45c608cd894feb5eeec24b867527a
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
* Introduce a null check before calling `gpio_padbased_override`
in `variant_configure_pads`.
* This prevents potential errors in cases where the
`variant_gpio_override_table` function returns a null pointer,
indicating that there are no override pads to configure.
BUG=b:334826281
TEST=Able to avoid hang incase there is no GPIO override.
Change-Id: I733210a08091b37eda6e6b0d6924aafd5e7e6280
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82628
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The CHECK_REV_IN_OPROM_NAME Kconfig option was introduced to solve the
problem of the PCI VID/DID combination of the Picasso iGPU not being
sufficient information to know which VGA BIOS file to run, so a new
function that additionally checks the PCI revision of that device was
introduced. Later it turned out that there might be a case where even
that isn't sufficient, so the soc_is_raven2() function is used in the
remap function to always use the correct VBIOS file.
Picasso is the only SoC that selected the CHECK_REV_IN_OPROM_NAME
Kconfig option, so all other SoCs are unaffected by this change.
Now that we use the VBIOS images with only the PCI VID and DID in the
CBFS file name for Picasso, SeaBIOS will find the VBIOS with the same ID
as the iGPU in CBFS and we don't need the workaround to add a third
VBIOS image via VGA_BIOS_DGPU_* that has the name that SeaBIOS expects.
This will result in SeaBIOS now running the VBIOS that has the same PCI
VID/DID as the hardware which will be the wrong one in the RV2 silicon
showing the PCO silicon PCI VID/DID, but that was also the case with the
VGA_BIOS_DGPU_* workaround where the board's Kconfig just selected one
of the two possible images during build time and hoped that it was the
correct one for that actual hardware. The only board where this patch
might cause a regression compared to the old behavior is the AMD Cereme
reference board with Pollock APU, but I'm not even sure if any coreboot
developer still has one of those boards, so I'm willing to accept that.
To properly solve the problem with SeaBIOS using the correct VBIOS file
in all cases, we'd need to generate that info during coreboot runtime
and somehow pass it to SeaBIOS, but that's out of scope for this patch.
TEST=On Mandolin with PCO silicon, the display output in both SeaBIOS
and Ubuntu still works. Booting Windows 10 via the pre-built EDK2
payload that I'm using also resulted in the display output working.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia6de533c536044698d85404427719b8f534870fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82598
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Type-C kernel driver no longer programs the AP mux, as of
https://review.coreboot.org/c/coreboot/+/82077. So remove device
references to the TCSS Mux control device from the Type-C port driver.
This eliminates the following kernel error which was observed as a
result of the kernel trying to program muxes it no longer has control
over:
[ 4.618600] cros-ec-typec GOOG0014:00: Failed to get mux info for port: 0, err = -95
[ 4.618608] cros-ec-typec GOOG0014:00: Configure muxes failed, err = -95
BUG=b:341331428
TEST=Run system reboot; configure mux kernel errors no longer seen.
Change-Id: I93e498b12b109c0e649a23a4a49868976a9ee06b
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82599
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1) Add all changes needed for early graphics
2) select MAINBOARD_USE_EARLY_LIBGFXINIT for nissa
The InnoLux (N156HCN-EBA C7) panel is used for the device tree.
BUG=b:296433986
TEST=On-screen text message seen during MRC training on Craask
Logs:
[NOTE ] MRC: no data in 'RW_MRC_CACHE'
[SPEW ] bootmode is set to: 0
[0.171409] DP PHY mode status not complete
[0.175509] DP PHY mode status not complete
[0.179799] DP PHY mode status not complete
[0.184087] DP PHY mode status not complete
[0.188376] DP PHY mode status not complete
[0.192665] DP PHY mode status not complete
[0.196954] DP PHY mode status not complete
[0.201243] DP PHY mode status not complete
[0.205532] DP PHY mode status not complete
[0.209821] DP PHY mode status not complete
[0.214110] DP PHY mode status not complete
[0.218397] DP PHY mode status not complete
[INFO ] Informing user on-display of memory training.
Change-Id: I33cfc5d1f8c25c344e598befd21c50a78a65275a
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78932
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This board is the CWWK variant based upon Alder Lake with 4 2.5 GbE
ports, similar boards are available in other port configurations. As a
low cost, relatively high performance board with 4 NICs, it is well
suited for networking or 'homelab' tasks.
CPU: Intel N100 or N350
Memory: DDR5-4800 SODIMM (max 16 GB)
NIC: 4x Intel I226-V 2.5 GbE
Expansion:
- M.2 2230 E key
- M.2 2280 M key
- USB 2.0 header
- Fan header
External ports:
- DC power
- 4x Ethernet
- Display Port
- HDMI
- 4x USB 2.0
- Micro SD
Working:
- Boots Debian 12 with SeaBIOS and EDK II payloads
- Serial port
- External USB ports
- DisplayPort / HDMI
- 4x Intel I226 2.5 GbE NICs
- M.2 ports
- Micro SD slot
- ACPI S3
Not working / not tested:
- Fan (ITE IT8613E)
- Audio
- S0ix
- Internal USB ports
VBT extracted from vendor UEFI firmware version ADLN 0.01 x64
(04/04/2023 11:42:38).
Change-Id: Ice9174d95c10afc6a22ddd15fb3be4fa38d329be
Signed-off-by: Brandon Weeks <me@brandonweeks.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Some proximity domain info are type specifics, e.g. base/size/dev
are effective for PD_TYPE_GENERIC_INITIATOR, but not for
PD_TYPE_PROCESSOR. Dump info per their type.
TEST=Build and boot on intel/archercity
Change-Id: I7e722a0577bba954efba3e91cc152c758c001d68
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Move proximity domain setting up to ahead of attach_iio_stacks()
so that proximity domain info could be ready before
attach_iio_stacks()/create_xeonsp_domains().
For example in SPR, is_iio_cxl_stack_res() refers to proximity
domain info, and it will be called in create_xeonsp_domains().
TEST=Build and boot on intel/archercity
No significant boot log difference except for proximity domain
dump info display are moved ahead (with correct contents).
Change-Id: I594f0ec0c23e3b62c3bdd917ebf6e45be6e4069e
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82267
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the `AZALIA_PIN_CFG_NC(0)` macro instead of `0x411111f0` and tidy up
some comments (align them and be consistent with capitalisation).
Tested with BUILD_TIMELESS=1, prodrive/hermes remains identical.
Change-Id: I1ff1197b1309fc0e5b978d6d36867a3f1a68c67c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
In the FSP case, the DDI descriptors aren't part of the devicetree and
are instead retrieved in romstage by calling the mainboard's
mainboard_get_dxio_ddi_descriptors function which allows updating the
descriptors during romstage where the devicetree is static. In the
openSIL case, the DDI configuration is first needed in ramstage, so we
can put this info into the devicetree and update it if needed in
ramstage.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3de12ff6af42e38751a3016efa313613677fa87a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82580
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Remove the TODO to update the chipset devicetree for Phoenix, since this
has already been done.
When re-checking the chipset devicetree, I found conflicting information
about the existence of the PCI bridge to an external PCIe port on bus 0
device 1 function 5, but after looking into this, I'm reasonably certain
that it either doesn't exist or at least wouldn't be usable, so I won't
add that one to the chipset devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8f0e1540ed45408e86186253d3982a7ba0065ac6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
This reverts commit f867c9c547.
The new verb table breaks external mic detection on brox.
Revert and use old verb tables instead.
BUG=b:330433089
BRANCH=main
TEST=Verified headset on Brox
When connected to audiojack in power_save state of legacy hda driver,
headset is detected and audio is resumed.
Change-Id: I0d8c092de6166b2c62f5ecc3deaf4960128e6106
Signed-off-by: Terry Cheong <htcheong@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82273
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-05-22 13:03:35 +00:00
536 changed files with 21740 additions and 1005 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
