The gaze17, like the oryp9, ties all resets for RTD3 to BUF_PLT_RST#
instead of using dedicated lines and ties the enable GPIO to 3.3VS.
Disable RTD3 config for the CPU PCIe RP and disable L23 for the PCH SSD
slot to fix suspend with Western Digital drives.
Change-Id: Iab3796d98ce74e09e74abb48b437e74a60c7b6b1
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The WD drives fail to go from D3cold to D0. Disabling L23 on the PCH port
allows it to work. Disabling L23 on the CPU port causes the CPU to not
reach C10 during suspend, so just remove the entire RTD3 config.
Change-Id: I3bf27fb0fe98e5ec05bff9cc18ab2dd8ac6c66b3
Signed-off-by: Tim Crawford <tcrawford@system76.com>
- Limit PL4 to 72W (1.6x TDP)
- Increase PL2 back to coreboot default value of 115W
- Increase PsysPL2 to 135W
Change-Id: I6d25a92d523d1d73dc6cdea6b630a47a832a54b6
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Declare dGPU pins in bootblock instead of ramstage as this conflicts
with the driver init.
Change-Id: I9464be9cbd25809367a112ea007c9e84ad8dfc55
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Fixes speaker detection and/or volume levels after a reboot.
Tested on Pop!_OS 22.04 with Linux 5.17.15.
Change-Id: I55f7e1d8b04233af3062741543a2279b02e167d8
Signed-off-by: Tim Crawford <tcrawford@system76.com>
System powers off on battery power when building the kernel. Reduce PL2
to 90W (2x TDP; same as oryp8) and limit PsysPL2 to 115W.
Change-Id: If5de789a39b2db56b4e3043b2cd7a7f8ad36f8d4
Signed-off-by: Tim Crawford <tcrawford@system76.com>
It is expected all boards using System76 EC firmware will select this
option. Enable it by default and drop the selection from the boards.
Change-Id: Id99d36eaf055a76b9e1eb732174017651de299a5
Signed-off-by: Tim Crawford <tcrawford@system76.com>
WD drives fail to resume from suspend.
Known to affect:
- WD Green SN350
- WD Blue SN550
Change-Id: I319d0a213dc76bf10105fa8e90a2c0e5a0f77f32
Signed-off-by: Tim Crawford <tcrawford@system76.com>
System powers off when booting on battery power from normal operations
such as logging in to GDM.
The EC firmware will update PL4 on AC adapter plug/unplug via PECI.
Change-Id: I6018dd62addf7a5d9302a3e3f6bce7c2d643b5c7
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Fixes system powering off under load when booting on battery.
Change-Id: Id9e74a9e91b3475fcf1b82198571139a43e98779
Signed-off-by: Tim Crawford <tcrawford@system76.com>
lemp11 is ADL-U, not ADL-P. Use the correct ID to override the values
and reduce PL1 to the TDP of 15W.
Change-Id: I285c906dc08d2882e6e84b463a63b69966b3c9f5
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Fix assertions for SATA and I2C1 devices GPIOs.
TODO: Test on darp8.
Change-Id: I89dbd212a7dbd55c84d8ebbb7420b960da8175af
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Change the FSP index for the SATA device to fix detection.
Drop the internal pull-up as there is already an external pull-up.
Change-Id: I5c97b3ee1f6208ca4e454647c8d19d7e7f025047
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Code taken from TGL base.
TEST=Boot MSI PRO Z690-A WIFI DDR4 and see all devices have SSID
applied
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I3a6d299ec40bac8e29d06926572e375d7d835e29
Fixes IRQ errors on oryp8 that cause conflicts with the PCH HDA device.
Change-Id: If0020d9bb6585f7b0fb2dabd3d8b2a3efdd86de2
Signed-off-by: Tim Crawford <tcrawford@system76.com>
BIOS must send the IP_LOAD HECI command to fetch the firmware for CPU
PCIe Gen5 and upload it via CPU REG BAR prior FSP Silicon Init.
Implementation based on Slimbootloader's
"Silicon/AlderlakePkg/Library/CpuPcieHsPhyInitLib" and FSP source.
TEST=Boot MSI PRO Z690-A and see the HSPHY FW is loaded and its recipe
and version is printed.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I6c6c11581e3d3d9bab0131fae6ef487cafe98080
Extend the code to support ADL-S PCIe Root Ports.
Based on DOC #619362 and #619501.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Ibb57ad5b11684c0079e384d9a6ba5c10905c1a23
Early EOP prevents disabling CSME.
Disabling CSME now occurs, but checking the result fails:
[DEBUG] HECI: ME state change send success!
[DEBUG] HECI: ME state change result failure!
CSME is disabled on subsequent boots.
Change-Id: I1c1416bb6537774f4bf09820c551b3b4ca7d1a38
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Fixes suspend with certain SSDs installed in the PCIe 4 slot.
Change-Id: Ib91b154963aeafe96c8118cbab89f0e70634e8bc
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The Bonobo has 2 AMPs: one for the speakers and one for the subwoofer.
Smart AMP data was collected using a logic analyzer connected to the IC
during system start on proprietary firmware. This data is then used to
generate a C file [1].
[1]: https://github.com/system76/smart-amp
Change-Id: I5389a9890563ebd3adb20096b6225f474bc006f9
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The addw1 supports an i9-9980HK and the addw2 uses an i7-10875H.
These CPUs have 8 cores and 16 threads. Fixes booting on addw2.
Change-Id: I4639b40c3ab9c6d6ad5abbbb3618c750c7d40695
Fixes: 6a93a45242 ("mb/system76/addw1: Add System76 Adder Workstation 1")
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The option table is shrunk 1 byte to force coreboot to invalid the table
and write the new defaults. This will ensure the IME is in the correct
mode on the next update.
Change-Id: I805c53fee55fea69fa3363fea0609858cc88f2d3
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Add a driver for systems with NVIDIA Optimus (hybrid) graphics using
GC6 3.0. The driver provides ACPI support for dynamically powering on
and off the GPU, and a function for enabling the GPU power in romstage.
Tested on system76/gaze15.
Change-Id: I2dec7aa2c8db7994f78a7cc1220502676e248465
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
This patch removes redundant DISABLE_HECI1_AT_PRE_BOOT config check for
heci1_disable(), once by caller (from various SoC) and again inside the
callee (heci1_disable) function.
As all callers of heci1_disable() function are doing
DISABLE_HECI1_AT_PRE_BOOT config enabled check, hence, the second check
inside the callee can be dropped.
BUG=b:228789015
TEST=Able to build and boot google/redrix with this change. CSE PCI
device is getting function disabled upon selecting
DISABLE_HECI1_AT_PRE_BOOT from SoC config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I47d7a9989e355987618d089f79c3340fcf4953ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63821
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch decouples HECI disabling interface a.k.a SMM or PCR or PMC
IPC etc. from DISABLE_HECI1_AT_PRE_BOOT kconfig as Intel ME BWG
recommends to disable the CSE PCI device while CSE is in
software temporary disable state.
BUG=b:228789015
TEST=Able to build google/redrix.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I66abc04d5e195515165a77b0166d004f17d029e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Agah USB-C port 0 is non-retimer port and it connects to TCSS port 2.
Bit[5:4] is for TCSS Port 2, so re-configure "TcssAuxOri" to 0x10 and "typec_aux_bias_pads" to 2 to correct the port.
BUG=b:210970640
BRANCH=NONE
TEST=emerge-draco coreboot chromeos-bootimage
Change-Id: I2d26777e850187aee0b676de13dff915474fed7b
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This allows for the option to persist the serial number and other
device-specific information when switching from stock ChromeOS and
upstream coreboot firmware images.
Change-Id: I12711f678259390fe9e31b7ca728344cc2875b0e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The ITE EC used on Nereid can take a long time to update, and especially
too long to erase. There is a 1 second timeout enforced on the EC erase
command, but Nereid's IT81302 will typically take about 5 seconds to
complete erase, and could take as long as 30.
Since this affects any Nissa variant using an ITE EC and it's nice to
make the entire Nissa project consistent, this change disables early
sync for all Nissa boards.
BUG=b:222987250
TEST=EC software sync is no longer attempted (and thus does not fail) on
Nereid.
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Change-Id: I55d36479e680c34a8bff65776e7e295e94291342
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Revert CdClock setting and use default value 0xff.
Previous problem was fixed by Jasperlake FSP in version 1.3.09.31,
so we can use the original CdClock setting in baseboard.
BUG=b:206557434
BRANCH=dedede
TEST="Built and verified on magolor platform to confirm FSP solution works"
Cq-Depend: chrome-internal:4662167
Change-Id: I50d65e0caaf8f3f074322cff5bbdc68bdb1bbf78
Signed-off-by: Simon Yang <simon1.yang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
To read data from an I2C EEPROM that uses 2 byte offsets or any other
I2C device that uses 2 byte offsets, first the two offset bytes are sent
to the device and then the data bytes are read from it. The main
difference to the existing i2c_read_bytes is that that function will
only send one offset byte to the I2C device.
TEST=Reading the contents of an EEPROM on the AMD Chausie board works
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I224e434bb2654aabef6302c1525112e44c4b21fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The lowest bound for L2 cache size on Socket P is 512 KiB.
This allows the use of cbfs mcache on all platforms.
This fixes building when some debug options are enabled.
Change-Id: I0d6f7f9151ecd4c9fbbba4ed033dfda8724b6772
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Commit 28e61f1634 "device: Use __pci_0_00_0_config in config_of_soc()"
significantly reduced the size of the bootblock. This makes the space
saving options, required to make to bootblock fit in the 32K SOC
limit, unnecessary.
TESTED: with configs/config.google_octopus_spi_flash_console the .text
size is 0x29c8 bytes which is still well below the 0x8000 SOC limit.
Change-Id: I208211d30cc2805113a16a02cdab957b8c584c92
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
`sa_lockdown_cfg` function ensures locking the PAM register hence,
skip dedicated calling into `sa_lock_pam()` from the SoC
`finalize.c` file. Dropped sa_lock_pam() call from ADL/CNL/EHL/JSL
and TGL.
Additionally, this patch enforces SA lockdown configuration for SKL
and ICL as well.
BUG=b:211954778
TEST=Able to build google/brya with these changes.
> localhost ~ # lspci -xxx | less
00:00.0 Host bridge: Device 8086:4601 (rev 04)
Bit 0 for all PAM registers a.k.a, PAMx_0_0_0_PCI.LOCK bit is set
(meaning locked).
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibd464d2507393ed0c746eb1fbd10e36092ed5599
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Commit 211be9c03 (soc/intel/cmn/{block, pch}: Migrate GPMR driver)
drops `dmi` prefix from `lockdown_cfg` function name.
This patch adds the `gpmr` prefix to the lockdown_cfg function to make
it meaningful.
BUG=b:211954778
TEST=Able to build google/brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Idaa0e089131ab125348e2430355041c4ee7971de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Alder Lake SoC deselects USE_FSP_NOTIFY_PHASE_POST_PCI_ENUM Kconfig
to skip FSP notify API (Post PCI Enumeration) and make use of native
coreboot driver to perform SoC recommended operations prior booting to
payload/OS.
BUG=b:211954778
TEST=Able to build brya with these changes and coreboot log with this
code change as below when ADL SoC selects required configs.
[INFO ] coreboot skipped calling FSP notify phase: 00000020.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I46f6ca791fb60b417d205d0a54705f3481deebd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
This area is used for storing AP RO verification data.
BUG=b:229670703
TEST=emerge-corsola coreboot
TEST=cbfstool /build/corsola/firmware/kingler/coreboot.rom layout
BRANCH=none
Change-Id: Id0a3304920c80987319d8072b8e443c41c1f1c47
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Camera LED flicker 3 times or so as sensor is being probed
during kernel boot.
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that driver skips
initial probe during kernel boot preventing camera LED flicker.
Corrects that by explicitly sequencing the reset GPIO and power GPIO
BUG=b:219644184
TEST=Build and boot on vell, observe whether camera LED flickers
Change-Id: I846ec4cb5c4527f5664699b31d0d561d390d938c
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63441
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is a bug floating around where communciation with the PMC fails
after transitions through S3/S4/S5. This CL does not address that issue.
However in working with error cases presented by a failing PMC, we're
forced into an early return in read_pmc_lpm_requirements(), which sets
up _DSM buffers in the SSDT for the PEP device.
The function itself returns void, so the error is swallowed regardless.
However returning early is not the appropriate action because it causes
the size of the buffer written into the _DSM method to change. This causes
the SSDT to change size and layout across an S3 or S4 transition, which
results in mayhem in the kernel, as the kernel is not expecting these
tables to change out from under it.
Instead of returning early, it's better to simply print the error and
keep going, attaching a zeroed out buffer for the substate requirements.
This results in an empty requirements mask for all states. From what I
can see in the kernel this is no more broken than today's behavior, as
this buffer seems to only be used for printing a debugfs file.
In fact in this particular case the kernel doesn't even notice, as this
buffer is copied out at boot, and not refreshed at resume.
BUG=b:230031158
TEST=hibernate and resume on Primus4ES
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: Ibe35d50b350b1b96dea313dfcbd00745970c16ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
We need to include the SMM handler to enable SCI events when ACPI is
enabled.
With this enabled we now see we have EC timeout problems while in SMI:
[SPEW ] SMI# #1
[WARN ] SMIx88 => 0x800
[DEBUG] Chrome EC: Set SMI mask to 0x0000000000000000
[DEBUG] Chrome EC: UHEPI supported
[ERROR] Timeout waiting for EC QUERY_EVENT!
[DEBUG] Clearing pending EC events. Error code EC_RES_UNAVAILABLE(9) is expected.
[ERROR] EC returned error result code 1
[DEBUG] Chrome EC: Set SCI mask to 0x00000000186601fb
We still need to debug that. I suspect we have problems reading from
the ACPI IO decodes 0x62 or 0x66.
BUG=none
TEST=Verify SMI handler runs
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ida0fcd634e620274e124a8669836f3974e0a2bf4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
* Use GPE 24 since it doesn't conflict with any existing GEVENTS.
* Remove IRQ 12 mapping since it's not used.
* Unmask IRQ1 in PM registers.
* Use the new SMITYPE_ESPI_SCI_B SCI.
BUG=b:227282870
TEST=Build and boot to OS in Skyrim.
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I7e9816d67500365ed1d2ee39ef184a1f60321ca1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
hardwaremain.c is the common ramstage entry to all platforms so move
out ACPI code generation (x86 specific) to boot state hooks.
Another reason to do this is the following:
On some platforms that start in dram it makes little sense to have
separate stages. To reduce the complexity we want to call the ramstage
main function instead of loading a full stage. To make this scheme
more maintainable it makes sense to move out as much functionality
from the 'main' function as possible.
Change-Id: I613b927b9a193fc076ffb1b2a40c617965ce2645
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63414
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CONFIG_ONBOARD_SAMSUNG_MEM is not used anymore.
Remove CONFIG_ONBOARD_SAMSUNG_MEM.
This patch was intended to be part of CB:59754, but was not included in
the latest patchset.
BUG = N/A
TEST = Boot Facebook FBG1701 Rev 1.0 - 1.4
Change-Id: Id351bcafe005cc1b3319d7186ece2b5b9a7f49ac
Signed-off-by: Frans Hendriks <fhendriks.eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
The current configuration is masking off IRQ 1 and IRQ 12 to the PIC.
This for some reason causes problems when using level triggered
interrupts. This change updates the PIRQ_MISC0 value to match what
skyrim is doing. This will enable level interrupts to work correctly.
BUG=b:218874489, b:160595155
TEST=Boot zork and verify keyboard still works. Boot with patch train
and verify keyboard works as expected.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I46b1fd68915c6f7aa4c34cdba57d24425752bc38
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This removes the need for a tool to generate simple identity pages.
Future patches will link this page table directly into the stages on
some platforms so having an assembly file makes a lot of sense.
This also optimizes the size of the page of each 4K page by placing
the PDPE_table below the PDE.
Change-Id: Ia1e31b701a2584268c85d327bf139953213899e3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The patch adds support to control CSE Lite firmware update dynamically.
In order to disable the CSE firmware update functionality, offset 0xf00
in the coreboot binary be updated with 0x1.
Run below command on the binary to disable CSE firmwar update
printf '\x01' | dd of=image-brya4es.serial.bin bs=1 seek=3840 count=1
conv=notrunc
BUG=b:153410586
TEST=Verified CSE firmware update functionality is not getting
triggered after updating the offset:0xF00 in the coreboot binary.
........................ CB Logs ......................................
[DEBUG] prev_sleep_state 5
[DEBUG] cse_lite: Number of partitions = 3
[DEBUG] cse_lite: Current partition = RW
[DEBUG] cse_lite: Next partition = RW
[DEBUG] cse_lite: Flags = 0x3
[DEBUG] cse_lite: RO version = 16.0.15.1752 (Status=0x0, Start=0x2000,
End=0x19bfff)
[DEBUG] cse_lite: RW version = 16.0.15.1752 (Status=0x0,
Start=0x205000, End=0x439fff)
rt_debug: pre_mem_debug.cse_fw_update_disable=1
[DEBUG] Boot Count incremented to 956
.......................................................................
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I9f234b142191eb83137d5d83f21e890e1cb828ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
The patch fixes the buggy code which tries to access the Descriptor
Region. The existing code doesn't use correct APIs to access the
Descriptor Region. Hence, error message is getting displayed during
the boot.
BUG=b:229003612
TEST=Build and verify no errors seen while accessing the Descriptor
Region.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ib144cc0845b7527e5a3032529b0802f961944b87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
PSP verstage can start at address 0 and use 200KB of PSP SRAM for
execution. Modify both the PSP SRAM start address and size for use by
PSP verstage.
BUG=b:220848544
TEST=Build Skyrim BIOS image with PSP verstage enabled.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I73e13b82faa0f443570a0c839e7699a79bdae024
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Create the mithrax variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:223091246
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_MITHRAX
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I7c2fa6a74cc8e37397dea7e67e8cfa6506a49bdb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
A new iteration of Google's TPM implementation will advertize a new
DID:VID, but otherwise follow the same protocol as the earlier design.
This change makes use of Kconfigs TPM_GOOGLE_CR50 and TPM_GOOGLE_TI50
to be able to take slightly different code paths, when e.g. evaluating
whether TPM firmware is new enough to support certain features.
Change-Id: I1e1f8eb9b94fc2d5689656335dc1135b47880986
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The services page documents various services and tools which are
provided by the project. It's more related to the infrastructure and
less related to the community section.
Thus, move it to the infrastructure section.
Change-Id: I0ca2aba8ae817cf874367fa17e567065aec99a93
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
In Sabrina, PSP verstage uses a unified SVC call ID with sub-commands.
Update the SVC calls for Sabrina to pass the SVC_VERSTAGE_CMD (command
ID) with individual subcommands and the corresponding parameters.
BUG=b:220848545, b:217414563
TEST=Build the Skyrim BIOS image with PSP verstage enabled.
Change-Id: I56be51aa1dfb00e5f0945014600de2bbbec289db
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Include <stddef.h> since we need it for 'size_t'.
Unused <stdlib.h> found using:
diff <(git grep -l '#include <stdlib.h>' -- src/) <(git grep -l 'memalign(\|malloc(\|calloc(\|free(' -- src/)
Change-Id: I3c2668013c16d6771268e8739b1370968c2e120b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <martinroth@google.com>
Although we're looking at updating the build system, we don't have a
strict timeframe that this will happen. Until it does, we'll be using
the current Jenkins configuration.
This commit give some minor updates to the instructions and current
state of the builders.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ifa094a6d0450da4ab58e23d7b56e65e6101ee931
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
This patch refactors the `pmc_lockdown_cfg()` to remove the helper
functions and uses the `setbits32` function to enforce bit locking
as applicable.
BUG=b:211954778
TEST=Able to build google/redrix with these changes and boot to OS.
> localhost ~ # iotools mmio_read32 0xfe0018c4
0x85000000 (bit 31 is set)
> localhost ~ # iotools mmio_read32 0xfe001024
0x00062610 (bits 4, 17 and 18 are set)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic96da4638aa689b5fa47a3356986ca5a0343fe36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch implements the required operations to perform prior to
booting to OS using coreboot native driver when platform decides
to skip FSP notify APIs i.e. Post PCI Enumeration.
The smbus `.final` operation ensures locking the TCO register when
coreboot decides to skip FspNotifyApi() calls.
BUG=b:211954778
TEST=Able to build google/brya with these changes and coreboot log with
this code change as below with ADL SoC skip calling into FspNotifyAPIs:
[INFO ] Finalize devices...
[DEBUG] PCI: 00:1f.4 final
> localhost ~ # lspci -xxx | less
00:1f.4 Intel Corporation Alder Lake PCH-P SMBus Host Controller
(rev 01)
Offset 8, Bit 12 a.k.a TCO Lock bit is set (meaning locked).
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie945680049514e6c5d797790a381a6946e836926
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Typically, the SPIBAR_HSFSTS_W1C_BITS macro is used to clear all HSFSTS
register bit-fields with the W1C attribute.
So far SPIBAR_HSFSTS_W1C_BITS is 1 byte width hence, missed to clear
SAF_CE (bit 8).
This patch expands the `SPIBAR_HSFSTS_W1C_BITS` macro to include
SAF_CE (bit 8).
BUG=b:211954778
TEST=Able to build google/brya with this patch and clear SPI controller
HSFSTS_CTL register Bits 0 to 4 and 8.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ifb58cef61118ca967e85226c1cf9db585e9ae4f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Add an option to the cbmem utility that can be used to append an entry
to the cbmem timestamp table from userspace. This is useful for
bookkeeping of post-coreboot timing information while still being able
to use cbmem-based tooling for processing the generated data.
BUG=b:217638034
BRANCH=none
TEST=Manual: cbmem -a 1234 to append timestamp, verify that cbmem -t
shows the added timestamp.
Change-Id: Ic99e5a11d8cc3f9fffae8eaf2787652105cf4842
Signed-off-by: Mattias Nissler <mnissler@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The front status LED on the Librem Mini is driven by the SATALED# GPIO
line configured for native function, so only shows disk activity for
SATA drives, but not NVMe. To allow it to show disk activity for NVMe
drives as well, reconfigure the GPIO as GPIO-OUT (rather than native
function), and configure it via ACPI so that the linux gpio-leds
driver will attach and use it accordingly.
This has the added benefit of allowing the user to reconfigure the
LED as they see fit via sysfs.
Test: boot Linux (PureOS) on Librem Mini v2 with NVMe drive, observe status
LED blinks during periods of disk activity (tested via 'stress').
Change-Id: I34c2a5f3fd1038266f4514544abfc1020da6f85b
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
According to Intel TA#724456, work around the higher SoC power
consumption in S0iX when CNVI has background activity.
BUG=b:201263040
TEST=Turn on this setting and build and verify on Drawcia.
The SLP_S0 toggling become slower or gone at the same CNVI
background activity.
Change-Id: I56439a406547e2ee1e47d34be14ecc9a8df04693
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63675
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 3e1943ec46 (soc/amd/cezanne: Force
resets to be cold) forced all resets on Cezanne to be cold resets to
work around a bug. Since the bug is fixed on Sabrina, this workaround
copied over from the Cezanne code isn't needed here, so sort-of revert
what the patch referenced above changed for Cezanne in the Sabrina code.
BUG=b:229105416
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I785e43124a9a969eeb129454e6e15dc245625250
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Break TPM related Kconfig into the following dimensions:
TPM transport support:
config CRB_TPM
config I2C_TPM
config SPI_TPM
config MEMORY_MAPPED_TPM (new)
TPM brand, not defining any of these is valid, and result in "generic" support:
config TPM_ATMEL (new)
config TPM_GOOGLE (new)
config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE)
config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE)
What protocol the TPM chip supports:
config MAINBOARD_HAS_TPM1
config MAINBOARD_HAS_TPM2
What the user chooses to compile (restricted by the above):
config NO_TPM
config TPM1
config TPM2
The following Kconfigs will be replaced as indicated:
config TPM_CR50 -> TPM_GOOGLE
config MAINBOARD_HAS_CRB_TPM -> CRB_TPM
config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL
config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE
config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM
config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Fix WLAN PCIE speed to GEN2. Dynamic switching between speeds is causing
the PSP to hang when resuming from S0ix suspend. The root cause is still
under investigation. Just disabling PSPP fixes the hang but causes poor
PLT performance.
BUG=b:228830362
BRANCH=guybrush
TEST=suspend_stress_test on AC and DC
Change-Id: I988365e51aca0d6515c5605b3032521cf59d8d30
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63722
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Alder Lake-N has single memory controller with 64-bit bus width. Alder
Lake common meminit block driver considers bus width to be 128-bit and
populates the meminit data accordingly. By setting half_populated to
true, only the bottom half is populated.
Ideally, half_populated is used in platforms with multiple channels to
enable only one half of the channel. Alder Lake N has single channel,
and it would require for new structures to be defined in meminit block
driver for LPx memory configurations. In order to avoid adding new
structures, set half_populated to true. This has the same effect as
having single channel with 64-bit width.
BRANCH=NONE
TEST=Build and boot ADL-N RVP.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I2ecc3018a1ab039990ba47898ff0e0e2ede695cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62913
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Looks like the `notify_data` struct array idea comes from the FSP 2.0
notify driver, which has a similar struct but with several additional
fields. However, there's no need for this mechanism in the CSE driver
because the struct only contains a condition (boolean) and a function
to execute, which can be expressed as a regular if-block.
Change-Id: I65fcb2fc02ea16b37c764f1fd69bdff3382fad18
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63708
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the osiris variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:229352299
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_OSIRIS
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I41e088a3415add86cba87c919af23494f816bb24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63650
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PCI Local Bus Specification Revision 3.0 requires that
multi-function devices always implement function 0. Because of
this, enabling UFS (PCI device 12.7) requires ISH (PCI device 12.0)
to be enabled as well.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: Ia8b9561973640edc5f7d0f579dd640e805c0af17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In order to enable the UFS controller (PCI device 12.7), the PCI
specification says that the device at function 0 in the same slot must
also be enabled, which is the ISH. Therefore, this CL enables both
the UFS controller and ISH.
TEST=Boot to kernel and check lspci output
00:12.0 Serial controller: Intel Corporation Device 54fc
00:12.7 Mass storage controller [0109]: Intel Corporation
Device 54ff
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: If15bcaffc8fd3bbbe4b181820993ab2d882bbbe1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62662
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
Also, drop `IGNORE_IASL_MISSING_DEPENDENCY` as it's no longer needed.
Change-Id: If56267e8a68897236d5ff73322317cbef7ab2243
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
The no-op `_DIS` methods can also be removed for the same reason.
Also, drop `IGNORE_IASL_MISSING_DEPENDENCY` as it's no longer needed.
Change-Id: I7e702e9318fbf68dbd883a145111e6beb6815b8b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
Also, drop `IGNORE_IASL_MISSING_DEPENDENCY` as it's no longer needed.
Change-Id: Ic37608ac9622b37cae6d81045740a033e9aa9d4f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
Change-Id: Ief40e790fdee336fd6c786e18cd01c41fa658c2c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
In addition, drop `IGNORE_IASL_MISSING_DEPENDENCY` from the two
mainboards using the MEC1308 code, `samsung/{lumpy, stumpy}`.
Change-Id: I5d5cdc28c2cfaa5dfcffd656060b931208977386
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
In addition, drop `IGNORE_IASL_MISSING_DEPENDENCY` from the only
mainboard using the SCH5545 code, `dell/snb_ivb_workstations`.
Change-Id: Ic462bd3dfa287744d4f733561de81c09c1c397e6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
The no-op `_DIS` methods can also be removed for the same reason.
Also, drop `IGNORE_IASL_MISSING_DEPENDENCY` as it's no longer needed.
Change-Id: I71275f2581b999d606f36773578b36dbdccf6452
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add PROP method under \_SB.DPTF.TPWR scope which will return static
worst case rest of platform power in miliWatts.
This value is static, which has to configured from devicetree of
overridetree for each platform
BUG=b:205928013
TEST=Build, boot brya0 and dump SSDT to check PROP method
Scope (\_SB)
{
Device (DPTF)
{
Device (TPWR)
{
Method (PROP, 0, Serialized)
{
Return (XXXX)
}
}
}
}
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I1415d2a9eb55cfadc3a7b41b53ecbec657002759
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
This CL adds the delay time 50 ms and 20 ms into the RTD3 sequence,
the reason is that the rise and fall times of each signal
may differ by board, and so those board-specific delays
must be taken into account when power sequencing.
We checked power on sequence requires enable pin prior to reset pin,
so added delay to meet the sequence.
Based on BH799BB_Preliminary_DS_R079_20201124.pdf in chapter 7.2.
BUG=b:228907551
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Idecb1c89655c9b8b720c3c65efc77e06e6a8b300
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Enable pen garage. Pen detect is active low.
BUG=b:229168203
TEST:Build and boot to OS in skyrim. Evtest work as expected
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "PRP0001:00"
Supported events:
Event type 0 (EV_SYN)
Event type 5 (EV_SW)
Event code 15 (SW_PEN_INSERTED) state 1
Properties:
Testing ... (interrupt to exit)
Event: time 1649922170.578779, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Event: time 1649922170.578779, -------------- SYN_REPORT ------------
Event: time 1649922172.070740, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I3bb07af6aebdc355a73148d8be79b1014147f61d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Followed the Brya series to lock the gpio pins in baseboard. Variant
should honor locked gpios from baseboard, but not the last. Variant can
add more gpios to lock if needed.
BUG=b:216671701
TEST='emerge-nissa coreboot chromeos-bootimage', flash and verify that
nivviks boots successfully to kernel.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ib34ca287596a6958407a944d0caf53f4bcc60d9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This patch is based on similar changes [1] done in Depthcharge projects,
which aimed to provide unified way to build host-side programs for
testing internal code. New test tools might benefit from it by having
same base code as unit-tests.
[1] https://crrev.com/c/3412108
TEST=make unit-tests
TEST=COV=1 make unit-tests coverage-report
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Iac4517ab6146fa3f2d2b7a20df54601ab2d04c3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch creates a helper function to set SPI controller VCL bit as
recommended by Intel Flash Security Specification.
BUG=b:211954778
TEST=Able to build google/brya and verified that SPI flash controller
MMIO register 0xC4 bit 30 is set.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie9a12db1bab81779fd8e7db90221d08da3c65011
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch creates a helper function to clear HSFSTS_CTL (offset 0x04)
register Bits 0 to 4.
As per Intel PCH BIOS spec section 3.6 Flash Security Recommendation,
it's important to clear all SPI outstanding status before setting SPI
lock bits.
BUG=b:211954778
TEST=Able to build google/brya with this patch and clear SPI controller
HSFSTS_CTL register Bits 0 to 4.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I62adba0d0cef1d4c53b24800f90b4fe76a9d78b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch creates a helper function to check if any SPI transaction
is pending.
As per Intel PCH BIOS spec section 3.6 Flash Security Recommendation,
it's important to ensure there is no pending SPI transaction before
setting SPI lock bits.
BUG=b:211954778
TEST=Able to build google/brya with this patch and no error msg seen
due to `SPI transaction is pending`.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibd3f67ae60bfcb3610cd0950b057da97ff74b5b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This is based on previous work done by a good friend of mine.
The notable differences between this board and the SFF variant is that:
- CMT has 4 more PCI/PCIe ports than SFF.
- CMT has 2 more SATA ports than SFF.
TESTED on Z220 CMT Workstation (boots to payload)
Change-Id: I2b298921e6f509440ec7b049e086c0878f708bd3
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set the BT USB device to use GPIO for the power status. This causes an
ACPI `_STA()` function to be generated that returns the power status of
the BT USB device, rather than always returning `0x1`. This `_STA()`
function can be used during boot to skip enabling the device (and
performing the associated sleep) if the device is already powered on.
BRANCH=None
BUG=b:225022810
TEST=Dump SSDT table for guybrush
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I72f6b28671efddfbef53f328d904a05f73f39efa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
If the device has enabled `use_gpio_for_status`, then call the `_STA`
method in `_ON` to determine if the device is already enabled. If it is
already enabled, return early to skip re-enabling the device and
performing the associated sleep.
This change is necessary since the Linux kernel does not call `_STA`
before calling `_ON`.
BRANCH=None
BUG=b:225022810
TEST=Dump SSDT table for guybrush
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I13aa41766555953b86eded4c72e3b317fe6db5c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63613
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the member `use_gpio_for_status` to the structure
`drivers_usb_acpi_config`, so the `devicetree.cb` can specify it.
This field is then used to initialize the corresponding field in the
structure `acpi_power_res_params` in `usb_acpi_fill_ssdt_generator()`.
The member `acpi_power_res_params::use_gpio_for_status()` is already
being used by `acpi_device_add_power_res()` to determine which version
of the `_STA()` method to output.
BRANCH=None
BUG=b:225022810
TEST=Dump SSDT table for guybrush
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I69eb5f1ad79f3b2980f43dcf4a36585fca198ec9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Replace 'struct lb_uint64' with 'typedef __aligned(4) uint64_t
lb_uint64_t', and remove unpack_lb64/pack_lb64 functions since it's no
longer needed.
Also replace 'struct cbuint64' with 'cb_uint64_t' and remove
'cb_unpack64' in libpayload for compatible with lb_uint64_t.
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: If6b037e4403a8000625f4a5fb8d20311fe76200a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Update the build scripts to inject variant specific SPDs into APCB.
BUG=None
TEST=Build and boot to OS in Skyrim boards with all the concerned memory
parts.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I3b3f6f248d54681c6f55c00660d1f2988ae906ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63600
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add supported memory parts and generate the associated DRAM part ID.
Also for MT62F2G32D8DR-031 WT:B memory part, add a custom SPD that
configures the DRAM speed at 5500 MHz. Use this custom SPD until that
part can operate at full speed (i.e. 6400 MHz).
BUG=None
TEST=Build Skyrim.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Id87e79f5d6187d57d74487841c09aa309f1450b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
APCB edit tool edits APCBs with LP4 specific SPDs. Introduce an option
to support different SPD magic so that the tool can be used to edit
APCBs with LP5 specific SPDs.
BUG=None
TEST=Build Skyrim board with LP5 specific SPDs. Build Guybrush board
with LP4 specific SPDs.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I8e96c89e4e5ce8e0567a17bf7685b69080fa1708
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63598
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PSP needs SPL file to boot. Introduce the support to add SPL file.
Currently Sabrina does not have a specific SPL file. Use Cezanne SPL
file as a placeholder.
BUG=b:224618411
TEST=Build and boot to OS in Skyrim after adding Sabrina specific SPL
file.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I222bb81b2babddc778b2cff858ef7979f85ac0e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63313
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The printed address ranges in the tree (resource allocator and even
some MTRR code) usually shows the range inclusive (meaning from start
address to the real end address of the range). Though there is still
some code in the MTRR context which prints the ranges with an exclusive
end. This patch aligns the printing of ranges in the MTRR code to be
consistent among the tree so that the shown end addresses are now
inclusive.
Change-Id: I0ca292f9cf272564cb5ef1c4ea38f5c483605c94
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
This patch enhances the GPMR driver to add public APIs for other IA
common code drivers and/or SoC code to utilize.
Also, migrated all PCR GPMR register definitions into the common
`pcr_gpmr.h` header file.
TEST=Able to build and boot google/redrix.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I87dca55a068366cb9a26a5218589166c1723da7f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
AMDFWtool maintains 2 copies of PSP Level2 entries - one in primary slot
A (Type 0x48) and another in backup slot B (Type 0x4A). On boards which
use VBOOT with 2 RW firmware slots, maintaining 2 copies of PSP Level2
entries in each FW slot is redundant and space-consuming. Introduce
option to maintain only one copy of PSP Level2 entries and point to it
from both slots A & B.
BUG=None
TEST=Build and boot to OS in Skyrim. Ensure that only one copy is added
to each FW slot. This achieved a space saving of 1.5 MB in each FW slot.
Before:
apu/amdfw 0x415fc0 raw 3043328 none
After:
apu/amdfw 0x415fc0 raw 1556480 none
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I06eef8e14b9c14db1d02b621c2f7207188d86326
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Previously, clock_configure() will configure the clocks to round up to
the next highest frequency bin. This seems non-intuitive. Changing
the logic to find an exact frequency match and will halt booting if no
match is found. Recently fixed a bug in CB:63311, where the clock was
being set incorrectly for emmc and was able to find it because of this
stricter check.
BUG=b:198627043
BRANCH=None
TEST=build herobrine image and try to set SPI frequency to number not
supported. Ensure device doesn't boot.
Change-Id: I9cfad7236241f4d03ff1a56683654649658b68fc
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
This patch adds `xhci_host_reset()` to reset XHCI controller and the
scope of this function is with SMM hence, compiling xhci.c for SMM as
well.
Also, refactored `xhci.c` code to keep PCI enumeration within the scope
of `ramstage` alone hence, guarded with `ENV_RAMSTAGE` env_variable.
BUG=b:227289581
TEST=Able to perform a call from `xhci_host_reset` from S5 smi handler.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie0dc0a64044f291893931726d26c08c8b964a3cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63551
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch calls into need_restore_mtrr() from the mtrr_use_temp_range
function to set `put_back_original_solution` to discard any temporary
MTRR range prior to boot to payload.
BUG=b:225766934
TEST=Able to build and boot google/brya to verify that
`remove_temp_solution()` is able to discard any temporary MTRR range
before booting to payload.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I2e00ec593847e1eb173d5ac77b15b50342860f89
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
`put_back_original_solution` variable in mtrr.c is static, but there is
a need to set put_back_original_solution outside of mtrr.c in order to
let `remove_temp_solution` to drop any temporary MTRRs being set
outside `mtrr_use_temp_range()`, for example: `set_var_mtrr()` function
is used to set MTRRs for the ROM caching.
BUG=b:225766934
TEST=Able to build and boot google/redrix.
Change-Id: Ic6b5683b2aa7398a5e141f710394ab772e9775e7
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch fixes an issue introduced by CB:59195 when QcLib
doesn't return a mem_chip_info structure to coreboot, and
solves some other minor leftover issues from that patch.
BUG=b:182963902,b:177917361
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: I0d59669adaf287d0eb7b58ccb0fe3f98e3d23281
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
We don't want to enable the speaker on init. It will be enabled while
using GPIO AMP codec in depthcharge.
BUG=b:223289882
TEST=boot Nipperkin and Dewatt and then verify the devbeep and gpio
values in kernel
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@google.com>
Change-Id: Id874421d7464b15be6e521576696bb97e6b22d6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The patch adds mechanism in the Alder Lake SoC code to control PCH
USB2 Phy power gating from brya board variant's devicetree. Please refer
Intel doc#723158 for more information.
BUG=b:221461379
TEST=Build and boot Gimble board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I3d80a3e36c6f8a3c0f174f955b11457752809f4d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Configure lcnt and hcnt directly to give the required frequency, tHIGH
and tLOW, instead of using rise and fall times. Aim for a frequency of
390 kHz to make sure it doesn't exceed 400 kHz on different boards.
BUG=b:227517802
TEST=Probe the clock line and check that it meets the requirements for
frequency, tHIGH and tLOW.
Change-Id: I4d4f877c1f0cd9aacd3fa152890b7ef82e059f78
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Create the craask variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_CRAASK
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: Icf03e3f18468d7dd207ab200fa2dcf96afd02f8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Fixes the following build error:
src/mainboard/google/brya/mainboard.c: In function 'variant_generate_s0ix_hook':
src/mainboard/google/brya/mainboard.c:157:40: error: parameter name omitted
void __weak variant_generate_s0ix_hook(enum s0ix_entry)
^~~~~~~~~~~~~~~
BUG=None
TEST=`abuild -a -x -c max -p none -t google/brya` now succeeds
Change-Id: Id578766e2a3b7647e920740dde3e356a7db39d4d
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Select the Bayhub LV2 driver, and implement power sequencing as per the
datasheet.
BUG=b:223304542
TEST=Check that connecting an SD card works as expected in the OS. Probe
the EN and RST signals and check the timing requirements are met.
Change-Id: Id1cca2024e06e5b2c7cefd22aa0b735bc542dc3b
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Keeping the PM timer enabled will disqualify an ADL system from entering
S0i3, and will also cause an increase in power during suspend states.
The PM timer is not required for ADL-N boards, therefore disabling it.
BRANCH=NONE
TEST=Build and boot ADL-N RVP. Verify system is entering S0i3 state.
localhost ~ # cat /sys/kernel/debug/pmc_core/substate_residencies
Substate Residency
S0i2.0 0
S0i3.0 13196801
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I44651bf55df8e71a0a5a9a33ecbb8322ecd18575
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Add a helper function mem_chip_info_size() as the size of
mem_chip_info structure is used in multiple places.
BUG=b:182963902,b:177917361
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: Iaada45d63b82c28495166024a9655d871ba65b20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63407
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The sinkhole exploit exists in placing the lapic base such that it
messes with GDT. This can be mitigated by checking the lapic MSR
against the current program counter.
Change-Id: I49927c4f4218552b732bac8aae551d845ad7f079
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch binds all FSP-M and FSP-S UPDs required for serial
redirection with `FSP_ENABLE_SERIAL_DEBUG` config to allow coreboot to
choose when to enable FSP debug output redirection to serial port.
For example:
PcdSerialDebugLevel => For controlling FSP debug level between FSP-M/S
SerialDebugMrcLevel => For controllig MRC debug level.
With this change FSP debug output will only be enabled when the user
enables `FSP_ENABLE_SERIAL_DEBUG` from site-local config with coreboot
serial image.
BUG=b:225544587
TEST=Able to build and boot brya. Also, the FSP debug log is exactly
the same before and with this code change.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I779c56b8b0fdebf45ea85b3b456a2d8066e26489
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63167
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 3ba6f8cdf (drivers/intel/fsp2_0: Add native implementation for
FSP Debug Handler) implements a native FSP debug handler.
However, coreboot still can't control when to redirect FSP debug
output to the serial console, i.e., at present, integrating a FSP debug
binary is enough to output FSP serial messages irrespective of whether
user is intended to see FSP debug log.
coreboot needs additional mechanism to control FSP debug binary to
redirect debug messages over serial port. This patch introduces a
config `FSP_ENABLE_SERIAL_DEBUG` to control the FSP debug output, user
to enable this config from site-local config file in case like to override
the default FSP serial redirection behaviour in more controlled way from
coreboot.
There could be scenarios as below:
Scenario 1: coreboot release image integrated with the FSP debug
binaries, is capable of redirecting to the serial console, but coreboot
decides to override the config as below to skip FSP debug output
redirection to the serial port.
`#`FSP Serial console disabled by default (do not remove)
`#`CONFIG_FSP_ENABLE_SERIAL_DEBUG is not set
Scenario 2: For coreboot serial image with FSP debug binaries integrated
but coreboot decides to skip FSP debug output redirection to the serial
port.
`#`FSP Serial console disabled by default (do not remove)
`#`CONFIG_FSP_ENABLE_SERIAL_DEBUG is not set
CONFIG_CONSOLE_SERIAL=y
CONFIG_CONSOLE_SERIAL_115200=y
CONFIG_UART_DEBUG=y
CONFIG_UART_FOR_CONSOLE=0
Scenario 3: The final image could be a coreboot serial image with FSP
serial redirection enabled to output to the serial port.
CONFIG_FSP_ENABLE_SERIAL_DEBUG=y
CONFIG_CONSOLE_SERIAL=y
CONFIG_CONSOLE_SERIAL_115200=y
CONFIG_UART_DEBUG=y
CONFIG_UART_FOR_CONSOLE=0
BUG=b:227151510
TEST=Able to build and boot google/redrix with all scenarios between #1--#3
and able to meet the expectation as mentioned above.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I0b008ca9d4f40bfa6a989a6fd655c234f91fde65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Commit 7a87433091 (mb/google,samsung: Drop
init_bootmode_straps()) got rid of the `mainboard_early_init()` function
call and weak definition in Sandy Bridge code. However, this function is
still used by several Sandy Bridge mainboards, so bring back the dropped
call and weak definition.
The aforementioned commit did not cause any build-time errors because it
did not remove the `mainboard_early_init()` function declaration.
Change-Id: I82768e9a187696d42b61be44d4aa048acc19d551
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
romstage uses FSP and SPD before these are verified.
Verify the FSP and SPD binaries in bootblock and measure these in
romstage.
BUG=N/A
TEST=Boot Facebook FBG1701 and check log for FSP and SPD verified in
bootblock.
Change-Id: I061affa5111fb14d69a8459575e0c72f71b1a1aa
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63446
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Warning for _SRS includes _SRS.
Warning for _DIS includes must have _SRS twice.
Remove requirement _SRS for _SRS is present.
Removed second _SRS for _DIS is present.
BUG=N/A
TEST=Verify correct message on built of facebook FBG1701
Change-Id: I1be740354b159e931e41323aef14e160cc09af19
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>´
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63250
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 1a4496e79f (soc/{apl,glk}: Allow to select the primary graphics
device) adds code to set the FSP parameter 'PrimaryVideoAdaptor' based
on the enum description of the FspmUpd.h for Apollo Lake.
Unfortunately, the comment in the header file does not match the
implementation in the FSP and hence setting PrimaryVideoAdaptor to
'GPU_PRIMARY_IGD' will be treated as if the selection was
'GPU_PRIMARY_PCI'. This in turn leads to Linux gfx driver issues for
earlier driver implementations.
This commit corrects the enum values for the FSP parameter to match the
implementation.
TEST=Boot into Linux on mc_apl1 and verify that graphics works.
Change-Id: Iedbc144fa809f6d4587f5223b235ee95579c48f7
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This patch fixes a problem where the `is_cse_devfn_visible` function is
unable to show the CSE device slot and function number properly.
BUG=b:211954778
TEST=Able to display CSE device slot and function number properly as
below:
Before:
[DEBUG] PCI: 00:16.0 final
[WARN ] HECI: CSE device 00.0 is disabled
[WARN ] HECI: CSE device 00.0 is disabled
[WARN ] HECI: CSE device 00.0 is disabled
[WARN ] HECI: CSE device 00.0 is disabled
[WARN ] HECI: CSE device 00.0 is disabled
With this code changes:
[DEBUG] PCI: 00:16.0 final
[WARN ] HECI: CSE device 16.1 is disabled
[WARN ] HECI: CSE device 16.2 is disabled
[WARN ] HECI: CSE device 16.3 is disabled
[WARN ] HECI: CSE device 16.4 is disabled
[WARN ] HECI: CSE device 16.5 is disabled
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I76a634c64af26fc0ac24e2c0bb3a8f397a65d77b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The patch adds support in the CSE Sub partition update procedure
to use GET_BOOT_PARTITION_INFO HECI command output to create the
region device for CSE RO and CSE RW. The GET_BOOT_PARTITION_INFO
HECI command provides CSE's RO and RW boot partition information.
Existing code relies on FMD file to get the CSE's boot partition's
(CSE RO and CSE RW) start and size details. This change make
independent of FMD file declaration with respect to CSE RO and CSE RW.
TEST=Build and verify the CSE RO and CSE RW region device information
through code instrumentation. Also, did boot test on Kano system.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ie9a83b77ab44ea6ffe5bb20673e109a89a148629
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
I don't really get around to review super I/O or superiotool patches any
more, so lower the maintenance level of those. If anyone else wants to
step up as new maintainer for those two, feel free to do so.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id7bd3c68c1adc0db82dab078291918742b453d4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The FSP needs to program VrPowerDeliverDesign configuration per
platform according to the platform capabilities to avoid incorrect
electrial/power parameters. This value is an enum of the available
power delivery segments that are defined in the Platform Design
Guide.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I74859e6735e59a15084a9e690b43f68341862833
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
To achieve low power consumption, we disable unused PCIe and SATA
pins at beadrix/overridetree.cb according to baseboard/devicetree.cb
and mainboard schematic. Original measured beadrix board's power
consumption is about 250 mW. After we disable unused PCIe and SATA
pins, as well as, enable the other low power MUX CL (3487086: USB
MUX: Update low power mode of MUX anx7447 used as MUX only |
https://chromium-review.googlesource.com/c/chromiumos/platform/ec/
+/3487086), the measured power consumption achieves about 110 ~ 116
mW, as well as, meets Google battery life for 14 days in the suspend
state and Intel low power consumption about 116 mW.
BRANCH=dedede
BUG=b:204882915
TEST=on beadrix, measured power consumption meets Intel power
consumption.
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: I79ec524c5ce8f2a79da4aeba084786fb9dac17af
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62776
Reviewed-by: Teddy Shih <teddyshihau@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are currently two issues related to the WLAN power sequencing on
nereid:
- If the EN pin GPP_B11 is not high during cold boot, the SoC gets stuck
in S3.
- During warm reboot, if we only assert RST without pulling the power
low, then the kernel crashes.
As a workaround while we investigate these issues, we pull the EN high
in S5, then actively drive it low in bootblock and high in romstage to
make sure it goes low during warm reboot.
BUG=b:227694137, b:225261075
TEST=Cold boot succeeds, and there's no kernel crash during warm reboot.
Change-Id: I1ca46d9649eff3f96a0e77db594d87288b29a83a
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
BUG=None
TEST=evtest works:
Select the device event number [0-14]: 9
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "PRP0001:00"
Supported events:
Event type 0 (EV_SYN)
Event type 5 (EV_SW)
Event code 15 (SW_PEN_INSERTED) state 1
Properties:
Testing ... (interrupt to exit)
Event: time 1649153020.275201, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Event: time 1649153020.275201, -------------- SYN_REPORT ------------
Event: time 1649153025.848689, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: time 1649153025.848689, -------------- SYN_REPORT ------------
Event: time 1649153028.383195, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Event: time 1649153028.383195, -------------- SYN_REPORT ------------
Event: time 1649153080.869155, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: time 1649153080.869155, -------------- SYN_REPORT ------------
Change-Id: I0d5134737fc758a43e1fff95e9f2a20200991bb1
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Some bytes in the descriptor need to be set differently for Type-C and
HDMI. To allow using a single firmware variant for both cases, update
the descriptor at runtime based on fw_config. This is a temporary
workaround while we find a better solution.
The byte values were determined by changing the following CSE strap and
comparing the generated descriptors:
Type-C: TypeCPort2Config = "No Thunderbolt"
HDMI: TypeCPort2Config = "DP Fixed Connection"
The default value before updating the descriptor is Type-C, but this was
chosen arbitrarily.
BUG=b:226848617
TEST=Type-C and HDMI both work on nereid with fw_config set correctly.
Change-Id: I2cc230e3bd35816c81989ae7e01df5d2c152062e
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sam McNally <sammc@google.com>
On nereid, we need to update the descriptor based on fw_config (see
the follow-up patch), so add support to update the descriptor at
runtime. This is a temporary workaround while we find a better solution.
This is basically adding back the configure_pmc_descriptor() function
removed in CB:63339, just making it generic and allowing it to update
multiple bytes at once.
BUG=b:226848617
TEST=With the following patch, Type-C and HDMI work on nereid.
Change-Id: I43c4d2888706561e42ff6b8ce0377eedbc38dbfe
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sam McNally <sammc@google.com>
The patch removes Kconfig CONFIG_ALDERLAKE_A0_CONFIGURE_PMC_DESCRIPTOR
code which updates PMC descriptor for an intermediate ADL-P SoC
stepping A0. Since intermediate ADL-P SoC is no longer supported and no
board is selecting the Kconfig, so remove the code that updates PMC
descriptor.
TEST=Build and boot Gimble board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I2a629353a4194a7505655346dcab4ef53059e0b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63339
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The patch SOC_INTEL_COMMON_BASECODE Kconfig for Comet Lake, Jasper Lake
and Tiger Lake SoCs. It allows access to intelbasecode/debug_feature.h
for Comet Lake, Jasper Lake and Tiger Lake SoCs.
TEST=Build code for Brya
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ie55ded673c8fa0edf2ca6789b15771bd2e56c95e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The patch adds a framework to control coreboot and Intel SoC features
dynamically. BIOS reads control information from OEM Section in the
Descriptor Region and control the developer selected features.
With the feature, debug team can control the selected SoC and coreboot
features without rebuilding coreboot.
In order to enable the feature, SOC_INTEL_COMMON_BLOCK_DEBUG_FEATURE has
to be selcted from mainboard.
The OEM section starts from offset:0xf00 till end of the Descriptor
Region(0xfff).
BUG=b:153410586
BRANCH=None
TEST=Verified CSE firmware update functionality on brya
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I5ba40926bd9ad909654f152e48cdd648b28afd62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Remove the subsystem device ID for HDA devices, so that the correct
Intel [8086:xxxx] is used. This was an old workaround for Windows
that is no longer required with a new driver.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I50c03a2df06af3ef1939afd0739e083a9056557f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch provides the set value for intel speed step in devicetree
for FSPS. Before that in case of not set value in device tree the
default value of disabled was overwritten by default enabled of FSP.
Test: mainboard/siemens/mc_ehl/variants/mc_ehl1
Check status of Bit 16 in MSR 0x1a0 after boot.
Change-Id: I0a5ef4968a27978116c21ce35b3818c6b36e086f
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This field was never meant to be filled out by coreboot, because it
can't know what the right value for this will be by the time the OS
is running, so anything coreboot could fill in here is premature.
This field is only read by the chromeos-specific `crossystem` utility,
not by kernel code, so if one does not run through depthcharge there'll
be many more broken assumptions in CNVS anyway.
Change-Id: Ia56b3a3fc82f1b8247a6ee512fe960e9d3d87585
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
K4U6E3S4AB-MGCL and K4UBE3D4AB-MGCL require special SPD files. This
commit overrides the default SPD files used for these parts
BUG=b:224884904
TEST=Verified that Dewatt SKU1 and SKU3 boot with changes
Signed-off-by: Robert Zieba <robertzieba@google.com>
Change-Id: Ibd08f109765933640ea3d0ad442873c30fa14bc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
This commit adds the ability to override the SPD file that is used for a
specific part.
BUG=b:224884904
TEST=Verified that generated makefile uses specified SPD file and that
it remains unchanged when this capability is not used
Signed-off-by: Robert Zieba <robertzieba@google.com>
Change-Id: I078dd04fead2bf19f53bc6ca8295187d439adc20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Checking whether a pointer is NULL after it has been dereferenced makes
zero sense. Make sure the `wifi_ssdt_write_properties()` function never
gets invoked with a NULL argument for the `dev` parameter, and simplify
the logic around the `is_cnvi_ddr_rfim_enabled` variable accordingly.
Change-Id: I3fbc9565e7e9b4e1c14a68f6a5fd779577045236
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
IASL reports warning on missing _SRS.
Devices have fixed configuration which is always enabled.
Remove _PRS for this fixed configuration.
BUG=N/A
TEST=built facebook monolith and verify no IASL warning is reported.
Change-Id: I554d3497255c1e50cdbe74b1cffc9f2c59fbae77
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63244
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
No functional change, just refactoring to make room for CMT variant.
Built with BUILD_TIMELESS=1 and no config included before and after.
$ diff master.rom build/coreboot.rom
$
TESTED: boots to SeaBIOS on HP Z220 SFF
Flashed bios region internally, mainboard also has FDO
(flash descriptor override) jumper that allows r/w to whole flash.
Change-Id: I6aaac75216b2d7c8bb48801454ce616ace3b1422
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Chause doesn't get to x86 bootblock without the SPL table binary in the
PSP directory table, so I assume that Majolica won't get to x86
bootblock either, since the Cezanne SoC default is not to include any
SPL table binary. This was caused by a combination of
commit 6c5ec8e31c (amdfwtool: Add options
to support mainboard specific SPL table) that caused a regression in
amdfwtool and commit c5b912f788
(soc/amd/cezanne: Allow to specify SPL table path in Kconfig) that
removed the default for the Cezanne SoC. Fix this by adding the default
SPL table file back to the fw.cfg file which will get ignored by
amdfwtool when a mainboard selects SPL_TABLE_FILE and specifies another
SPL table binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ica960e5422da50899a2d9c192863188174e0bcff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Use the SPL table binary from the config file if no override is
specified via the spl-table command line argument. This fixes a
regression caused by commit 6c5ec8e31c
(amdfwtool: Add options to support mainboard specific SPL table).
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I93419a878b41b1dfcbf58d930740aaae553120f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This patch removes different implementation to cache the SPI ROM between
early and later boot stage where SPI ROM caching doesn't need even
advanced implementation like `mtrr_use_temp_range()` as SPI ROM ranage
is always mapped to below 4GB hence, simple `set_var_mtrr()` function
can be sufficient without any additional complexity.
BUG=b:225766934
TEST=Calling into `fast_spi_cache_bios_region()` from ramstage is able
to update the temporary variable range MTRRs and showed ~44ms of boot
time savings as below:
Before:
90:starting to load payload 1,084,052 (14)
15:starting LZMA decompress (ignore for x86) 1,084,121 (68)
16:finished LZMA decompress (ignore for x86) 1,140,742 (56,620)
After:
90:starting to load payload 1,090,433 (14)
15:starting LZMA decompress (ignore for x86) 1,090,650 (217)
16:finished LZMA decompress (ignore for x86) 1,102,896 (12,245)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I43973b45dc6d032cfcc920eeb36b37fe027e6e8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63221
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch delays removing `temporary` MTRR snapshots to avoid conflicts
with other operations attached with same `BS_PAYLOAD_BOOT/BS_ON_EXIT`
boot state.
BUG=b:225766934
TEST=Having variable MTRR snapshot using display_mtrrs() is able to
list only the permanent MTRRs and all temporary MTRRs are removed
prior to boot to payload.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I602dca989745159d013d6573191861b296f5d3ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch migrates a few useful MTRR functions as below from
`earlymtrr.c` file to newly created common stage file `mtrrlib.c`.
1. get_free_var_mtrr
2. set_var_mtrr
3. clear_all_var_mtrr
These functions can be used to perform the MTRR programming from IA
common code SPI driver as `fast_spi.c` without requiring two separate
implementations for early boot stage (till romstage) and for ramstage
onwards.
BUG=b:225766934
TEST=Able to build and boot google/redrix board to ChromeOS.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I2c62a04a36d3169545c3128b4231992ad9b3699d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch enriches coreboot FSP2.0 driver to extract the FSP timestamp
from FPDT (Firmware Performance Data Table) and display right after
FSP-S exits (from `fsp_silicon_init()` function), based on SoC user
selects the required `DISPLAY_FSP_TIMESTAMPS` config.
The prerequisite to this implementation is to have FSP binary built with
`PcdFspPerformanceEnable` PCD set to `TRUE` to allow FSP to populate
the FPDT HOB.
BUG=b:216635831
TEST=Able to dump FSP performance data with DISPLAY_FSP_TIMESTAMPS
Kconfig selected and met the FSP prerequisites.
+--------------------------------------------------+
|------ FSP Performance Timestamp Table Dump ------|
+--------------------------------------------------+
| Perf-ID Timestamp(ms) String/GUID |
+--------------------------------------------------+
0 460253 SEC/52c05b14-0b98-496c-bc3b04b50211d680
50 460263 PEI/52c05b14-0b98-496c-bc3b04b50211d680
40 460274 PreMem/52c05b14-0b98-496c-bc3b04b50211d680
1 495803 9b3ada4f-ae56-4c24-8deaf03b7558ae50
2 508959 9b3ada4f-ae56-4c24-8deaf03b7558ae50
1 515253 6141e486-7543-4f1a-a579ff532ed78e75
2 525453 6141e486-7543-4f1a-a579ff532ed78e75
1 532059 baeb5bee-5b33-480a-8ab7b29c85e7ceab
2 546806 baeb5bee-5b33-480a-8ab7b29c85e7ceab
1 553302 1b04374d-fa9c-420f-ac62fee6d45e8443
2 563859 1b04374d-fa9c-420f-ac62fee6d45e8443
1 569955 88c17e54-ebfe-4531-a992581029f58126
2 575753 88c17e54-ebfe-4531-a992581029f58126
1 582099 a8499e65-a6f6-48b0-96db45c266030d83
50f0 599599 unknown name/3112356f-cc77-4e82-86d53e25ee8192a4
50f1 716649 unknown name/3112356f-cc77-4e82-86d53e25ee8192a4
2 728507 a8499e65-a6f6-48b0-96db45c266030d83
1 734755 9e1cc850-6731-4848-87526673c7005eee
....
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ia1b7f6b98bafeec0afe843f0f78c99c2f34f50b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
* Use dedicated ALERT pin to resolve NO_RESPONSE error/status while
getting target configuration.
* Configure the ESPI to operate at 16 MHZ since operating at 33 MHz
causes boot stall.
BUG=b:226635441
TEST=Build and Boot to OS in Skyrim. Ensure that EC <-> AP communication
is working fine through Host Command debug logs in EC console, ectool
version command.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I951afdada8ee4f917cdeba8e287e5a2ae77c97ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63286
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Found an issue where emmc and sd clocks were being misconfigured due
to using incorrect integer values when called instead of the defined
enums. Fixing by splitting the clock_configure_sdcc() function into
two (sdcc1 and sdcc2) as there was no commonality between the two
cases anyway. As a result, we can also get rid of the clk_sdcc enum.
BUG=b:198627043
BRANCH=None
TEST=build herobrine image and test in conjunction with CB:63289
make sure assert is not thrown.
Change-Id: I68f9167499ede057922135623a4b04202f4da9b5
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
elog_gsmi_cb_mainboard_log_wake_source is called from SMI and causes
eSPI transactions. If the SMI interrupts an ongoing eSPI transaction
from the OS it will conflict and cause failures. Removing this call to
avoid conflicts. This can be re-enabled after refactoring
google_chromeec_get_mask to use ACPI MMIO.
BUG=b:227163985
BRANCH=gubyrush
TEST=No 164 errors detected during suspend_stress_test
/sys/firmware/log output after resume before change:
SMI# #1
ELOG: Event(B0) added with size 9 at 2022-03-31 19:52:51 UTC
GPIO Control Switch: 0xcf000000, Wake Stat 0: 0x00000000, Wake Stat 1: 0x00000000
ELOG: Event(9F) added with size 14 at 2022-03-31 19:52:51 UTC
Chrome EC: clear events_b mask to 0x0000000000000000
after change:
SMI# #6
ELOG: Event(B0) added with size 9 at 2022-03-31 19:50:19 UTC
GPIO Control Switch: 0xcf000000, Wake Stat 0: 0x00000000, Wake Stat 1: 0x00000000
ELOG: Event(9F) added with size 14 at 2022-03-31 19:50:19 UTC
Change-Id: I3320e3fb8bd9e9e0db84332e1d147a0af25f7601
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63280
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since Sabrina uses the image slot header (ISH) that depends on the AMD
A/B recovery scheme that depends on the multi-level PSP directory
support, the multi-level support gets automatically selected by passing
Sabrina as SoC name to amdfwtool, so passing the --multilevel command
line switch to amdfwtool isn't needed.
TEST=Timeless build results in identical binary for chausie
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I98154d5b47daca6ae7952ffd3175d98ea3e01845
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The fch_i23c_pad_init implementation was written without looking at any
reference code and turned out to not work properly on hardware. Before
this function writes to the MISC_I23C_PAD_CTRL registers, the value read
back is 0x3000003c which results in the I2C bus communication to work
while the 0x300003fc the code writes to the register breaks the I2C
communication. Removing the code that sets bits 6..9 fixes the I2C bus
communication.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ie6758b3d13c59b20ce810225fca8a365713b7a2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63234
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Contradicting the PPR #57243 version 1.56, the I2C3 pad control register
in the MISC ACPIMMIO region is the same new I23C pad type as the
corresponding registers for I2C0..2 and not the older I2C pad control
register type used on Picasso and Cezanne. All I2C pads being of the new
I23C type is in line with the GPIOMUX settings for the pins used by
I2C0..3 that can alternatively connect the pins to an I3C controller.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I51b0ddf8ba2ccfee823e3d4d26a77b11825b1029
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63233
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We set T3 as 300ms to meet Elan's spec, but the resume/suspend times
are greater than 500ms, which is the spec for Chromebooks.
The actual kernel timing has been measured, and given the ACPI delay
after deasserting reset in addition to the delay until the kernel
driver accesses the device, delaying only 200ms in the ACPI method is
also sufficient to meet the 300ms requirement.
BUG=b:223936777
BRANCH=none
TEST=build and test touchscreen function on DUT.
TEST=suspend, wake DUT and check touchscreen function.
Change-Id: I6b04cf6392d924aed01ca36b720f889b88d92311
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
C0 has no redriver, so enable SBU muxing in the SoC.
C1 has a redriver which does SBU muxing, so disable SBU muxing in the
SoC. However, this also disables AUX biasing when the pins are
configured as NF6. So instead configure the C1 AUX bias pins as GPO.
BUG=b:227259673
TEST=Voltages are correct on the C0 and C1 AUX bias pins
Change-Id: Ic0af662ecc1c6cee15b4ae98cb02deeefc93a71e
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Add new board Clevo L14xMU (TGL).
GPIOs were configured based on schematics.
Tested and working:
- On-board RAM (M471A1G44AB0-CWE)
- DIMM slot (tested Crucial CT16G4SFD8266.16FJ1 / MTA16ATF2G64HZ-2G6J1)
- Graphics (GOP driver), including HDMI
- Keyboard
- I2C touchpad (including interrupt)
- TPM (with interrupt on Windows, only polling on Linux [1])
- microSD Card reader
- both NVME ports
- Speakers
- Microphone
- Camera
- WLAN/BT (CNVi)
- All USB2/3 ports including Type-C
- Thunderbolt detects my work laptop in TB Control Center
(I couldn't test anything more due to security policy.)
- TianoCore
- internal flashing with flashrom on vendor firmware
Note on TPM:
The vendor sets Intel PTT to default-on in newer CSME images, which
conflicts with the dTPM. Currently, there are two ways to make it work:
1) Boot vendor firmware once to let it disable PTT via CSME firmware
feature override.
2) Use Intel Flash Image Tool (FIT) to set "initial power-up state" to
disabled.
Boots fine:
- Debian testing, unstable (Linux 5.16.14, 5.17.0-rc6)
- Windows 10 21H2 (Build 19044.1586)
Untested:
- Thunderbolt (see above)
- Type-C DisplayPort
- S-ATA
Doesn't work:
- TPM interrupt on Linux [1]
- All EC related functions - EC driver is WIP
- WLAN/BT (PCIe) - gets detected but can't be enabled
- 3G/LTE (not powered without EC driver)
- Fn-Keys
- S0ix
- UCSI
- Fan control
- Battery info
[1] https://lkml.org/lkml/2021/5/1/103
Change-Id: I4c4bef3827da10241e9b01e12ecc4276e131a620
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
When rebuilding coreboot the empty fit table added to added to CBFS
stays the same so the build process sees no reason to update the file.
In the meantime ifittool did update that file for instance to add
microcode update entries. So each time coreboot is rebuilt the entries
are appended to the FIT table which runs out of space at some point.
One way to deal with this is to clear the fit table when setting the
pointer inside the bootblock.
TESTED: Now running 'make' again on prodrive/hermes does not report an
error with a filled FIT table.
Change-Id: Ia20a489dc90a4ae704e9ee6d532766899f83ffcc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63036
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Flame graphs are used to visualize hierarchical data, like call stacks.
Timestamps collected by coreboot can be processed to resemble
profiler-like output, and thus can be feed to flame graph generation
tools.
Generating flame graph using https://github.com/brendangregg/FlameGraph:
cbmem -S > trace.txt
FlameGraph/flamegraph.pl --flamechart trace.txt > output.svg
TEST=Run on coreboot-enabled device and extract timestamps using
-t/-T/-S options
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I3a4e20a267e9e0fbc6b3a4d6a2409b32ce8fca33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The patch logs CSE RO's write protection information for Alder Lake
platform. As part of write protection information, coreboot logs status
on CSE RO write protection and range. Also, logs error message if EOM
is disabled, and write protection for CSE RO is not enabled.
TEST=Verify the write protection details on Gimble.
Excerpt from Gimble coreboot log:
[DEBUG] ME: WP for RO is enabled : YES
[DEBUG] ME: RO write protection scope - Start=0x1000, End=0x15AFFF
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I766d5358bb7dd495b4a9b22a2f1b41dc90f3d8d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Now that the amdfwtool support for Sabrina is in place, change the
SoC name parameter passed to amdfwtool from Cezanne to Sabrina.
The fw.cfg file still points to the Cezanne binaries, but since
commit 9cb0a05dfb (soc/amd/sabrina: Add
prompt for AMDFW_CONFIG_FILE) this can be overridden via the Kconfig
config file in the build. As soon as the Sabrina PSP binaries are
available in 3rparty/amd_blobs, the fw.cfg file will be updated to use
the correct ones for Sabrina.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I53a8de222e39bd2b92c07661b6c52a02fb651609
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63189
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In newer AMD SoCs, the image slot header is used in the AMD A/B recovery
scheme, so set recovery_ab to true when need_ish is true. Also move the
block of code before the process_config call, since that call will
already use the recovery_ab field of the cb_config struct.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I65903765514f215bf5cc9b949d0b95aff781eb34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63184
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the specific SPD hex file for the Samsung memory part with
updating the part number into the SPD table. The ABL needs to
identify the part by checking SPD data to do the proper tuning.
BUG=b:224884904
TEST=Build, validate the SPD data has been applied.
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ia54726ce8c1bae46dcd4fed3df509ef184914e94
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Some solutions require readable form of timestamps, which does not
contain spaces. Current descriptive timestamp names do not meet this
criteria. Also, mapping enums to their text representation allows for
quick grepping (use of grep command) to find relevant timestamps in the
code.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Ifd49f20d6b00a5bbd21804cea3a50b8cef074cd1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
On FreeBSD, every build target would show warnings from its
builtin printf().
Change the regexp to be compatible with BSD sed.
This will avoid noise like "printf: 4.14-1278-g5d74ccf1c3: not
completely converted".
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Change-Id: I1c0c260fd8d42e23a612a353a288e472cc068c8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
We don't want to enable the speaker on init. It will be enabled while
using GPIO AMP codec in depthcharge.
BUG=b:223289882
TEST=boot guybrush and verify the devbeep and gpio value in kernel
Change-Id: Ic949cc95556913a2afef4a683a49eaa1e07e6147
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Only Cr50 versions starting at 0.5.5 support long IRQ pulses, so this
feature is enabled based on the value of the board_cfg register (see
CB:61722).
However, Ti50 versions below 0.0.15 don't support the board_cfg
register, and trying to access it will cause I2C errors (see CB:63011).
Also, all Ti50 versions only support long IRQ pulses. Therefore, add a
workaround to force enable long IRQ pulses for boards using Ti50
versions under 0.0.15, instead of enabling it based on board_cfg. This
workaround will be removed once all Ti50 stocks are updated to 0.0.15 or
higher.
BUG=b:225941781
TEST=Boot nivviks and nereid to OS with Ti50 0.0.14 and check there are
none of these I2C errors:
[ERROR] I2C stop bit not received
[ERROR] cr50_i2c_read: Address write failed
[ERROR] cr50_i2c_tis_status: Failed to read status
Change-Id: Iaba71461d8ec79e8d6efddbd505339cdf1176485
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63160
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move WWAN power on sequence from OS to coreboot. This can save the
WWAN initial time about 10S. Another purpose is power resource be
removed because we don't power off the LTE in S0ix.
BUG=b:223490884
TEST=FM101-GL work as expected.
Enumerate time from
[ 17.747145] usb 4-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 17.760192] usb 4-2: New USB device found, idVendor=2cb7, idProduct=01a2, bcdDevice= 5.04
[ 17.760210] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 17.760215] usb 4-2: Product: Fibocom FM101-GL Module
[ 17.760220] usb 4-2: Manufacturer: Fibocom Wireless Inc.
[ 17.760224] usb 4-2: SerialNumber: 9c88998f
to
[ 3.936409] usb 4-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 3.966695] usb 4-2: New USB device found, idVendor=2cb7, idProduct=01a2, bcdDevice= 5.04
[ 3.989989] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.003813] usb 4-2: Product: Fibocom FM101-GL Module
[ 4.019760] usb 4-2: Manufacturer: Fibocom Wireless Inc.
[ 4.019762] usb 4-2: SerialNumber: 9c88998f
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I0f3fe999ae3a109b739629948b619a389a9059b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
The patch deselects ALDERLAKE_A0_CONFIGURE_PMC_DESCRIPTOR Kconfig for
ADL RVP board. The flag updates PMC settings in the IFD for Alder Lake
A0 silicon. As Alder Lake A0 is intermediate stepping, and the IFD is
locked in the production systems, so the Kconfig is deselected.
TEST=Build the coreboot for adlrvp
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I966be42ba662861f4a6933d7275ecc13860220f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
coreboot.pre doesn't follow the standard Make conventions. It gets
modified by multiple rules, and thus we can't compute the dependencies
correctly. This means we need to manually delete it before starting the
dependency calculations.
i.e., Building firmware with the seabios payload now works correctly.
Fixes: dd6efce934 ("Makefile: Add .SECONDARY")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If5fa3f0b8d314369a044658e452bd75bc7709397
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Change the DXIO descriptors to match the default PCIe lane mapping on
the chausie board. With this configuration and a board-level rework to
bypass the EC control of the NVMe SSD power supply rail, this
configuration results in the SSD being detected on the root port on bus
0 device 2 function 3 and usable as boot device. This was also validated
against the schematics revision B.
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib74988b741f748d240ef09fa0dba8885bdc5e706
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63161
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Follow the Moli GPIO Table_20220324.xlsx to update it.
1.Set A15 as the default value.
2.Set A14, A19 NC.
3.Set C3, C4 as the default value.
4.Set D9 as the default value.
5.Set E5, E13 as the default value.
6.Set R4, R5 as the default value.
7.Update E14.
8.Set E12 as the default value.
9.Set D16 as the default value.
BUG=b:220821454
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Ia54256244111a99cb130b74f78c37815099a021a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This patch adds an option to disable loglevel prefixes. This patch helps
to achieve clear messages when low loglevel is used and very few
messages are displayed on a terminal. This option also allows to
maintain compatibility with log readers and continuous integration
systems that depend on fixed log content.
If the code contains:
printk(BIOS_DEBUG, "This is a debug message!\n")
it will show as:
[DEBUG] This is a debug message!
but if the Kconfig contains:
CONFIG_CONSOLE_USE_LOGLEVEL_PREFIX=n
the same message will show up as
This is a debug message!
Signed-off-by: Igor Bagnucki <igor.bagnucki@3mdeb.com>
Change-Id: I911bb601cf1933a4c6498b2ae1e4cb4d4bc85621
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
ESPI is not initialized in PSP. Hence any attempt to write to port80
causes failure to boot. Disable PSP postcodes for now and re-enable it
later after ESPI is initialized in PSP.
BUG=b:224618411
TEST=Build and boot to OS in Skyrim.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I73b7ddec50936f7836f915f459ca0bdc0777cb22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This is done to work around a hang when SMU writes to port80. Remove it
after the issue is fixed.
BUG=b:224618411
TEST=Build and boot to OS in Skyrim.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ic152c295954d33ef1acddb3b06f0c6bbfbfb38ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63122
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to the PCIe CEM specification, the deassertion of PERST#
should occur at least 100ms after the assertion. To ensure the 100ms
delay requirement is met, calculate the elapsed time since assertion. If
it is smaller than 100ms, do an extra delay.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the measured PERST# time:
[DEBUG] mtk_pcie_domain_enable: 432517 us elapsed since assert PERST#
[INFO ] mtk_pcie_domain_enable: PCIe link up success (17 tries)
And the SSD information in boot log is as follows:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
BRANCH=cherry
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Ie2b7b6174abdf951af5796ab5ed141c45f32fc71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Described in PCIe CEM specification sections 2.2 (PERST# Signal) and
2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should be
delayed 100ms (TPVPERL) for the power and clock to become stable.
Instead of asserting PERST# right before PCIe initialization and waiting
for 100ms, which is currently the only function of 'mtk_pcie_pre_init',
so that the extra 100ms delay in ramstage is avoided.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
BRANCH=cherry
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Id5b9369e6f8599f93415588ea585c952a41c5e7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add early init support for MT8195 platform.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
BRANCH=cherry
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: I4eb7da53ff76c385cab18bbf84970e96b61662ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add support for "early_init_data" region, which can be used to store
data initialized in an early stage (such as bootblock), and retrieve it
in later stages (such as ramstage).
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
BRANCH=cherry
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: I01f91b7fe2cbe4f73b5c616bb7aae778dee27d9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
SMU locks up sometimes if the port80 enable bit is cleared in the ESPI
Decode register. Add a config to choose between clearing the entire ESPI
Decode Register vs retaining the port80 enable bit.
BUG=None
TEST=Build and boot to OS in Skyrim.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ia5ee012ac4858d6dd43827274169edf622a70489
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
The memory initialization reference code didn't support returning
DRAM information in the old platforms, for example MT8192 and MT8195.
So we have to add a new configuration USE_CBMEM_DRAM_INFO to make
sure the common code will try to get DRAM information on new
platforms supporting that.
BUG=none
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Iebe9ea0c1d01890b09fdf586813d85adde9702e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The current pmif register setting for low power mode is incorrect,
which is causing suspend failure. The issue of suspend failure is that
SRCLKENA0 will not be pulled down. EC will not be informed AP is
suspending now becuase of this. Therefore, add pmif_spmi_set_lp_mode()
to correct the setting.
This implementation is based on chapter 3.7 in MT8186 Functional
Specification.
BUG=b:215639203
TEST=test of suspend and resume pass.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Change-Id: I2d02198f19f9cb052fba612c02404a6af1a10adb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The Cherry follower projects may choose Max98390 for audio output
so we have to add a new config CHERRY_USE_MAX98390. Also, the
'dojo' device is the first one to use it.
BUG=b:204391159
BRANCH=cherry
TEST=emerge-cherry coreboot
TEST=Verify beep function through CLI in depthcharge successfully
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Change-Id: I9b6bc5a5520292dd502b0389217f5062479b4490
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63083
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch moves `pmc_clear_pmcon_sts` function into common code and
remove SoC specific instances.
Accessing PMC GEN_PMCON_A register differs between different Intel
chipsets. Typically, there are two possible ways to perform GEN_PMCON_A
register programming (like `pmc_clear_pmcon_sts()`) as:
1. Using PCI configuration space when GEN_PMCON_A is a PCI configuration
register.
2. Using MMIO access when GEN_PMCON_A is a memory mapped register.
SoC users to select `SOC_INTEL_MEM_MAPPED_PM_CONFIGURATION` Kconfig to
perform GEN_PMCON_A register programming using PMC MMIO.
BUG=b:211954778
TEST=Able to build brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I8d15f421c128630f928a1b6a7e2840056d68d7b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeff Daly <jeffd@silicom-usa.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
The eSPI CS function only exists on AGPIO30.
We will need to rework all boards to make eSPI function.
I also fixed the comments on the other eSPI pins.
BUG=b:226635441
TEST=Build skyrim
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib03c0a7dcad31d10dd4bad0d10a0184ab84aef9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Although coreboot can allocate resources above 4G, Linux does not
consider those allocation valid when there is no region above 4G in
_CRS and disables the device.
TESTED: x220 with and external GPU via the expresscard slot. Linux
does not touch the BARs allocated above 4G.
Change-Id: If1be9a2c1e03e5465fd3b164469511eca60edc5a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Regarding JEDEC Standard No. 21-C, Release 30, page 13, DDR4_SPD_72B_SO_RDIMM
and DDR4_SPD_72B_SO_UDIMM values are respectively 0x08 and 0x09.
There is no affected board in coreboot tree.
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Id4e9c3814e2e7f379917bf93f7975af3aad31dbb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This patch uses the FSP event handler feature and updates with coreboot
native debug implementation to unify the debug library between coreboot
and FSP.
BUG=b:225544587
TEST=Able to build and boot Brya with the same FSP debug log before and
with this code changes.
Before:
Register PPI Notify: DCD0BE23-9586-40F4-B643-06522CED4EDE
Install PPI: 8C8CE578-8A3D-4F1C-9935-896185C32DD3
Install PPI: 5473C07A-3DCB-4DCA-BD6F-1E9689E7349A
The 0th FV start address is 0x000F961B000, size is 0x00150000, handle is 0xF961B000
Register PPI Notify: 49EDB1C1-BF21-4761-BB12-EB0031AABB39
Register PPI Notify: EA7CA24B-DED5-4DAD-A389-BF827E8F9B38
Install PPI: B9E0ABFE-5979-4914-977F-6DEE78C278A6
With this code change:
[SPEW ] Register PPI Notify: DCD0BE23-9586-40F4-B643-06522CED4EDE
[SPEW ] Install PPI: 8C8CE578-8A3D-4F1C-9935-896185C32DD3
[SPEW ] Install PPI: 5473C07A-3DCB-4DCA-BD6F-1E9689E7349A
[SPEW ] The 0th FV start address is 0x000F95C0000, size is 0x00160000, handle is 0xF95C0000
[SPEW ] Register PPI Notify: 49EDB1C1-BF21-4761-BB12-EB0031AABB39
[SPEW ] Register PPI Notify: EA7CA24B-DED5-4DAD-A389-BF827E8F9B38
[SPEW ] Install PPI: B9E0ABFE-5979-4914-977F-6DEE78C278A6
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4a0530a282657e379a00c3e7d0ed8148dd5e9196
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch assigns FSP handler event for FSP-M and FSP-S with coreboot
romstage and ramstage debug handler when FSP_USES_CB_DEBUG_EVENT_HANDLER
Kconfig is enabled.
BUG=b:225544587
TEST=Able to build and boot brya. Also, verified the FSP debug log is
exactly same before and with this code change.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I665def977faaae45f6f834d75e8456859093ba49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Implement the GPIOs that have been changed from genesis.
- Connect scaler UART on pins C12/C13
- Connect the HDMI redriver I2C on C18/C19
- Connect the iMX8 signals on D1/D2/D3/D21/D22
- Connect the EC interrupt on D14 (same as on scout)
- Connect PCH_TYPEC_UPFB on E15 (same as on genesis)
- Configure as not connected the following unused pins: D23, E11, E12,
F11 -> F22, H0, H8, H9
BUG=b:200876872
TEST=moonbuggy boots
Change-Id: Ie9cafe81e391bce6ab7ffbe23c2d57b407d146f3
Signed-off-by: Pablo Ceballos <pceballos@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Using the GPP_F22 as mic mute switch based on the latest schematic.
BUG=b:223737606, b:216110896
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
The mic_mute event is changed when the mic_mute GPIO pin is switched.
Event: time 1647939954.639995, type 5 (EV_SW), code 14 (SW_MUTE_DEVICE), value 0
Event: time 1647939954.639995, -------------- SYN_REPORT ------------
Event: time 1647939954.648152, type 5 (EV_SW), code 14 (SW_MUTE_DEVICE), value 1
Event: time 1647939954.648152, -------------- SYN_REPORT ------------
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I6f7176afbd64f7c080f02369f195043a2df88e5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Currently, we control the GPP_D0 in the flash_fp_mcu in order to
program the component's firmware. If we set this pin to NC, then we
can't control the GPP_D0 output low/high and that make the system fails
to program the component's firmware. This patch sets the GPP_D0 to GPO
to fix it.
BUG=b:204679292
BRANCH=firmware-brya-14505.B
TEST=program the component's firmware
Change-Id: I2f58c324f807a067dbe338f044a33dc9622ca469
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Image Slot Header (ISH) is a new feature.
The rom layout for A/B recovery with ISH:
EFS -> PSP L1 0x48 -> ISH A -> PSP L2 A -> BIOS L2 A
0x4A -> ISH B -> PSP L2 B -> BIOS L2 B
The newer 55758 will updated about the boot priority and update retry
in ISH header.
Change-Id: Ib0690cde1dce949514c7aacebe13096b7814ceff
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57747
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
To control I2S in MT8195 for dojo project, we need to enable adsp
power before audio power. Therefore, we need to update bus protection
steps to correct the setting.
TEST=build pass
BUG=b:204391159
BRANCH=cherry
Signed-off-by: Chun-Jie Chen <chun-jie.chen@mediatek.com>
Change-Id: I0bcf1ddeebf0d3df0a1d6b22273123be1aaf85a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63106
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch implements coreboot native debug handler to manage the FSP
event messages.
`FSP Event Handlers` feature introduced in FSP to generate event
messages to aid in the debugging of firmware issues. This eliminates
the need for FSP to directly write debug messages to the UART and FSP
might not need to know the board related UART port configuration.
Instead FSP signals the bootloader to inform it of a new debug message.
This allows the coreboot to provide board specific methods of reporting
debug messages, example: legacy UART or LPSS UART etc.
This implementation has several advantages as:
1. FSP relies on XIP `DebugLib` driver even while printing FSP-S debug
messages, hence, without ROM being cached, post `romstage` would
results into sluggish boot with FSP debug enabled.
This patch utilities coreboot native debug implementation which is
XIP during FSP-M and relocatable to DRAM based resource for FSP-S.
2. This patch simplifies the FSP DebugLib implementation and remove the
need to have serial port library. Instead coreboot `printk` can be
used for display FSP serial messages. Additionally, unifies the debug
library between coreboot and FSP.
3. This patch is also useful to get debug prints even with FSP
non-serial image (refer to `Note` below) as FSP PEIMs are now
leveraging coreboot debug library instead FSP `NULL` DebugLib
reference for release build.
4. Can optimize the FSP binary size by removing the DebugLib dependency
from most of FSP PEIMs, for example: on Alder Lake FSP-M debug binary
size is reduced by ~100KB+ and FSP-S debug library size is also
reduced by ~300KB+ (FSP-S debug and release binary size is exactly
same with this code changes). The total savings is ~400KB for each
FSP copy, and in case of Chrome AP firmware with 3 copies, the total
savings would be 400KB * 3 = ~1.2MB.
Note: Need to modify FSP source code to remove `MDEPKG_NDEBUG` as
compilation flag for release build and generate FSP binary with non-NULL
FSP debug wrapper module injected (to allow FSP event handler to execute
even with FSP non-serial image) in the final FSP.fd.
BUG=b:225544587
TEST=Able to build and boot brya. Also, verified the FSP debug log is
exactly same before and with this code change.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I1018e67d70492b18c76531f9e78d3b58fa435cd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Clang complains that the terniary '?' operator is executed before the
bitwise '|'. This is true and desired in this case. Being explicit
about won't hurt however.
Change-Id: I27d1fc1c19e1dab3d1c82e407151eaa46f8c7b03
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
FSP 2.3 spec introduced new version of NV storage HOB
FSP_NON_VOLATILE_STORAGE_HOB2. This new HOB addresses the limitation of
FSP_NON_VOLATILE_STORAGE_HOB which can support data length
upto 64KB. FSP_NON_VOLATILE_STORAGE_HOB2 allows >64KB of NVS data to be
stored by specifying a pointer to the NVS data.
FSP_NON_VOLATILE_STORAGE_HOB HOB is deprecated
from FSP 2.3 onwards and is maintained for backward compatibility only.
This patch implements the parsing method for
FSP_NON_VOLATILE_STORAGE_HOB2 HOB structure .The HOB list is first
searched for FSP_NON_VOLATILE_STORAGE_HOB2. If not found we continue
to search for FSP_NON_VOLATILE_STORAGE_HOB HOB.
BUG=b:200113959
TEST=Verified on sapphire rapids and meteor lake FSP platform that
introduces FSP_NON_VOLATILE_STORAGE_HOB2 for retrieving MRC cached data.
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I27647e9ac1a4902256b3f1c34b60e1f0b787a06e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch adds EFI status code macros in `efi_datatype.h` to implement
FSP debug event handler natively in coreboot.
Added `PiStatusCode.h` and `StatusCodeDataTypeId.h` files for
`UDK base >= 2017`, as these files were added with UDK version 2017.
BUG=b:225544587
TEST=Able to build and boot Brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib2debb6a50581456783dc9f22f892f8f92a25509
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch resolves compilation issue of including `efi_datatype.h`
in other stage files due to unresolved EFI_PROCESSOR_INFORMATION macro
definition. EFI_PROCESSOR_INFORMATION defined in `Protocol/MpService.h`
hence, included to resolve compilation issue.
TEST=Able to build brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4c0ca4f8876e46f1748ffc9e3b90de00ead80ebd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Include paths fixup macro for vboot was broken and was adding
unnecessary prefix to paths from $(coreboottop). This patch adds correct
filters to fix this behavior.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I264e715fa879a4e56b6e5f5423916298e8780a2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Putting
src/soc/*/common before src/soc/*/*, and
src/superio/common before src/superio/*,(which is already moved but
with duplicated folder "common")
can make the variables in
common Makefile get the expected value before they are used in other
subdirs.
The later "*" also contains "common", which needs to be eliminated by
"filter-out".
Then we can put some common variables from all the subdir Makefile.inc
to the common Makefile.inc to reduce code redundancy.
Change-Id: I99597af22cac6d12aaef348789664cd7db02ba06
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The commit message has a (soft) line length limit of 72 characters and
the subject has a (soft) line limit of 65 characters. This change
updates checkpatch to warn at those limits.
Note that neither of these are hard limits because git & gerrit can both
handle longer lines, it just doesn't look good.
Change-Id: I4ef131a65254e2b184b05e0215969aef97e12712
Signed-off-by: Martin Roth <martin@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
For SoC that don't support LPC any more the definition of the PSP soft
fuse chain bit 15 has changed. Earlier SoCs that still supported a
physical LPC bus used this bit to determine if the I/O port 0x80 POST
code are sent to LPC or eSPI. Newer SoCs like Sabrina don't have a
physical LPC bus any more and on those this bit selects if the PSP debug
output is sent to the SoC's MMIO UART or an UART on I/O port 0x3F8 that
the needs to be decoded to eSPI.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0bffb6efacc585a1d02a0455b32f7cf8662b3232
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Ti50 FW under 0.15 is not support board cfg command which causes I2C
errors and entering recovery mode. And ODM stocks are 0.12 pre-flashed.
Add workaround for the old Ti50 chip.
BUG=b:224650720
TEST=no I2C errors in coreboot.
[ERROR] cr50_i2c_read: Address write failed
[INFO ] .I2C stop bit not received
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ieec7842ca66b4c690df04a400cebcf45138c745d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Precision is a Mid Tower chassis platform with very similar mainboard
to OptiPlex 9010. It has one more PCIe port and a PCI port. It also
incorporates C216 chipset instead of Q77 and enables DRAM ECC support.
Other changes are related to subsystem ID and fan control
initialization.
TEST=Boot Dell Precision T1650 and launch Debian 10.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I4ec2013d5f53af36cab0d1def19272f5ef1a9516
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
New boards like Dell Precision T1650 will be added as variants, in
subsequent commit. They share most of the code, except some EC
initialization tables, PCIe port configuration and subsystem ID.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I4075f0ae3b24892fcc2be07061a01f8070659239
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
The patch add APIs to check CSE Region's write protection information.
Also, adds helper functions to get the SPI controller's MMIO address
to access to BIOS_GPR0 register. The BIOS_GPR0 indicates write and read
protection details.
During the coreboot image build, write protection is enabled for CSE RO.
It is enabled through a Intel MFIT XML configuration.
TEST=Verify write protection information of CSE Region
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: If1da0fc410a15996f2e139809f7652127ef8761b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
coreboot needs to propagate the CnviDdrRfim value info of the feature
enable/disable state into the CNVi via the WiFi DSM ACPI object. This
will be consumed by the Wi-Fi driver and it will act according to
CB enablement configuration. This patch adds _DSM method for that.
Add support for following 2 functions in _DSM method
- Function 0: Function Support Query Returns a bitmask of functions
supported.
- Function 3: RFI enablement 0 Feature Enable 1 Feature Disable
Note: Wifi Dsm already has provision for SAR. This patch will add
additional support to return RFIM structure based on UUID.
BUG=b:201724512
TEST=Build, boot brya0 and dump SSDT entries
Method (_DSM, 4, Serialized) // _DSM: Device-Specific Method
{
ToBuffer (Arg0, Local0)
If ((Local0 == ToUUID ("7266172c-220b-4b29-814f-75e4dd26b5fd")))
{
ToInteger (Arg2, Local1)
If ((Local1 == Zero))
{
Return (Buffer (One)
{
0x09
})
}
If ((Local1 == One)){}
If ((Local1 == 0x02)){}
If ((Local1 == 0x03))
{
Return (Zero)
}
Return (Buffer (One)
{
0x00
})
}
Return (Buffer (One)
{
0x00
})
}
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I217b736df3d4224a6732d1941a160abcddbd8f37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Update the two load line slope settings for the telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
VDD scale: 73331 -> 94623
VDD offset: 1893 -> 1847
SOC scale: 31955 -> 29904
SOC offset: 852 -> 756
BUG=b:217963719
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
pass AMD SDLE/Stardust test
Change-Id: Icad97644dd9391a325dfe1dbb1ec176e1f6d3dc3
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The Pubkey(0), PSP bootloader(1) and IKEK(0x21) should be put to
level 2 only for A/B recovery for Sabrina, which is going to be the
long term and A/B recovery layout only. So the amdfwtool should be
changed for Sabrina.
The old levels of these 3 FWs are for Cezanne, which doesn't use AB
recovery now. Just set the specific field levels in generic Cezanne
folder for demo. Leave the fw.cfg in Guybrush unchanged.
Change-Id: I11092b52927b2c526a5be719104ba39a790b6fa8
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
The current behavior does not actually check if a device is present
before enabling the corresponding gpp_clkx_clock_request_mapping bits
which may cause issues with L1SS. This change sets the corresponding
gpp_clkx_clock_request_mapping to off if the corresponding device is
disabled.
BUG=b:202252869
TEST=Checked that value of GPP_CLK_CNTRL matched the expected value
when devices are enabled/disabled, checked that physically removing a
device that is marked as enabled also disables the corresponding clk req
BRANCH=guybrush
Signed-off-by: Robert Zieba <robertzieba@google.com>
Change-Id: I77389372c60bdec572622a3b49484d4789fd4e4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61259
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix the HWM sequence matching to the chassis. HWM sequence for SFF
was incorrectly passed to MT chassis HWM initialization.
Vendor code also applies a fix-up for MT/DT chassis. This fixup was
missing one register read compared to the vendor code. Add the missing
read and guard the fixup depening on the returned value to match the
vendor code behavior. Not doing so resulted in increased fan speeds
on Dell Precision T1650 compared to Dell's firmware.
TEST=Boot Dell Precision T1650 and hear the fans are as silent as on
Dell's firmware
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I5c0e1c00e69d66848a602ad91a3e83375a095f44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
On boards where PSP uses ESPI to write postcodes, update the verstage to
do it after ESPI initialization.
BUG=b:224543620
TEST=Build and boot to OS in Nipperkin. Ensure that there are no
attempts to write the post code from PSP verstage before ESPI
initialization.
Change-Id: I1b78931c741c75dc845c9b34e3b2b896221f2364
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mohan Viswanathan
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This patch adds TCSS XHCI device ID for ADL-N CPU which is required
for USB3 port enumeration.
Document Reference: 645548 revision 1.0 (Chapter 2.3)
BUG=None
BRANCH=None
TEST=Check if device is detected correctly and ACPI entries are
generated for device 0d.0
Change-Id: Id5d42d60eb05137406ef45b9e87e27948fc3b674
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Windows 11 installer expects the TPM to reside under \\_SB_.PCI0 in
ACPI device hierarchy, otherwise the TPM is not detected. Hardcode
the path to fix the issue.
TEST=Boot Windows 11 on Clevo NV41MZ and see the TPM is detected
correctly
TEST=Boot Ubuntu 20.04 on Clevo NV41MZ and see the TPM is detected
correctly
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Change-Id: If0b3136e3eb8eb1bb132132a5f3a7034bdd3b424
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This CL adds the delay time into the RTD3 sequence, which will turn
off the eMMC controller (a true D3cold state) during the RTD3 sequence.We checked power on sequence requires enable pin prior to reset pin, added delay to meet the sequence and test passed on various eMMC SKUs.Base on BH799BB_Preliminary_DS_R079_20201124.pdf in chapter 7.2.
BUG=b:224648680
TEST=USE="project_primus" emerge-brya coreboot chromeos-bootimage
test suspend stress 2500 cycles passed on primus
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Change-Id: I1ab4fdf0ee73b819b3c203e995ac9d5ae0d24bd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update iPXE stable from commit id ebf2eaf515:
Mar 18 10:24:08 2019 +0000
[intel] Add PCI ID for I219-V and -LM 6 to 9
to commit id 6ba671acd9:
Jan 17 16:17:17 2022 +0000
[efi] Attempt to fetch autoexec script via TFTP
This brings in 424 new commits and fixes the build with coreboot-sdk
2021-09-23_b0d87f753c.
TEST=Build PC Engines apu2 board and boot it over network with the
iPXE
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Ide12a3a3082f9ea027e180518a80e6c0772b1232
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Prevents bad things from happening later when these new nodes are used.
This issue is hard to observe because:
1. Heap is zero-initialized, so you need to use allocated memory
filling it with non-zero values, free, allocate it again, use
uninitialized.
2. Most of allocated memory is not freed.
3. Implementation of free() does something only for one last malloc'ed
block, making most of freed memory unavailable for future
allocation.
Change-Id: I38a7ec1949d80f7a2564fac380ce94de6056a0c7
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62928
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
cr50_get_board_cfg() may be called in ramstage for some mainboards in
order to determine the BOARD_CFG register's value. The code was
written assuming that the firmware version was already retrieved, but
for boards calling this in ramstage, this is not the case. Therefore,
instead of using the cached cr50_firmware_version (which is all 0s in
ramstage at that time), use the cr50_get_firmware_version function
instead.
BUG=b:225206079, b:220685274
BRANCH=firmware-brya-14505.B
TEST=boot on brya0 and see:
[INFO ] Firmware version: B2-C:0 RO_B:0.0.11/4d655eab RW_B:0.6.93/cr50_v3.94
[INFO ] Enabling GPIO PM b/c CR50 has long IRQ pulse support
in the logs.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ia6e5f4965a8852793d2f95e6eb21ea87860335a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Despite the SMBus device being function 0 of the FCH PCI device, the
MMIO resource of the FCH IOAPIC is on the LPC device which is function 3
of the same PCI device, so move the FCH IOAPIC initialization code to
the LPC device. Since the HPET was enabled in the same function, also
move it to the LPC device initialization.
TEST=On Mandolin both IOAPICs are still correctly detected by Linux.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I585afd463c1c00cd87ced0617e7802503c5deba5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58334
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently memory parts that use the same SPD are assigned the same ID by
spd_tools. This commit adds support for exclusive IDs. When given an
exclusive ID a memory part will not share its ID with other parts unless
they also have the same exclusive ID.
BUG=b:225161910
TEST=Ran part_id_gen and checked that exclusive IDs work correctly and
that the current behavior still works in their abscence.
Signed-off-by: Robert Zieba <robertzieba@google.com>
Change-Id: Ife5afe32337f69bc06451ce16238c7a83bc983c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
"Total time" calculation changed after CL 59555 to include
"1st timestamp" value in the calculation. This patch restores original
Total Time calculation where "1st timetamp" is subtracted from
"jumping to kernel". If pre CPU reset timestamps are added (negative
timestamps), "Total time" calculation still includes the pre-reset time
as expected.
1) Before https://review.coreboot.org/c/coreboot/+/59555:
0:1st timestamp 225,897
1101:jumping to kernel 1,238,218 (16,316)
Total Time: 1,012,281
2) After https://review.coreboot.org/c/coreboot/+/59555:
0:1st timestamp 225,897
1101:jumping to kernel 1,238,218 (16,316)
Total Time: 1,238,178
3) After this patch:
0:1st timestamp 225,897 (0)
1101:jumping to kernel 1,238,218 (16,316)
Total Time: 1,012,281
BUG=none
TEST=Boot to OS, check cbmem -t on Redrix board
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I0442f796b03731df3b869aea32d40ed94cabdce0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The APCB files that provide the firmware components running on the PSP
some mainboard-specific information like the DRAM interface
configuration. Those files aren't yet in the upstream 3rdparty/blobs
repository, so only add those files if they are present and print that
no APCB was added and the image won't boot if they aren't present.
TEST=Both cases behave as expected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1e8621901741b8b0531fe134273b47e85911e19f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
The EC values will be changed when entering S3, S4 or S5, so move
the function that stores the current settings outside of logic
that restricts it to S4 or S5. This means the state isn't lost
when entering S3.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ia007a8ad9c08a309489e9f64f1ed311858bfcd10
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The patch deselects ALDERLAKE_A0_CONFIGURE_PMC_DESCRIPTOR Kconfig which
updates PMC settings in the IFD for Alder Lake A0 silicon.
As Alder Lake A0 is intermediate stepping, and the IFD is locked in the
production systems, so the Kconfig is deselected.
BUG=b:190588098
BRANCH=firmware-brya-14505.B
TEST=Build the coreboot for Gimble
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I81fe7c792dd82d9d547d318ebda55ee4a0f3ac96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Although the panel initializes fine and the fw recovery screen is
displayed without issues, the current power-on sequence of the
PS8640 violates the spec of the PS8640, which can be confirmed by
measuring it with an oscilloscope.
The sequence is:
- set VDD12 to be 1.2V
- set VDD33 to be 3.3V
- pull hign PD#
- pull down RST#
- delay 2ms
- pull high RST#
- delay more than 50ms (55ms for margin)
- pull down RST#
- delay more than 50ms (55ms for margin)
- pull high RST#
This flow will increase 110ms if firmware display is enabled in
krabby. For normal booting flow, the firmware will not be enabled,
so it will meet boot time requirements of Chrome OS. (Less than 1s.)
Datasheet name: PS8640_DS_V1.4_20200210.docx.
Chapter: 14.
BUG=b:222650141
TEST=show fw display normally in krabby.
TEST=result of waveform meets the spec.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I7706c56dc7fc13ac84c0d52a6e534bc0988e8fd3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Right now, the PSPP policy that controls if the PCIe lanes can be
dynamically downgraded to a lower speed to save some power needs to be
disabled in order for the link training to be successful. Once this
feature is working, PSPP will be reenabled.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6ea602596acb8e5ea92076386e80102c3bc757af
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Right now, the PSPP policy that controls if the PCIe lanes can be
dynamically downgraded to a lower speed to save some power needs to be
disabled in order for the link training to be successful. Once this
feature is working, the PSPP policy will be switched to balanced again.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I85a06f322c4ddff25c3a858e2b79c84b36c48932
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Fix the FSP headers and replace void pointers by fixed sized integers
depending on the used mode to compile the FSP.
Change request here:https://github.com/intel/FSP/issues/59
This is necessary to run on x86_64, as pointers have different size.
Add preprocessor error to warn that x86_64 FSP isn't supported by the
current code.
BUG=b:200113959
TEST=Verified on Meteor Lake platform, without any compilation error
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I1f33db43f7932cf6d165d0c70a0e2922dad00a09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Commit 215a97ee1c (soc/intel/adl/chip.h:
Convert all camel case variables to snake case) converted the camel case
used in the parameter name to snake case, but
commit bd529e2e20 (mb/google/nissa/var/
nivviks: Add TcssAuxori for nivviks) still used the old names which
breaks the upstream build. his patch is intended to be merged via
fast-path before the 24h are over to fix the tree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2b9049553889c77bd8c59a2c4564d36d836a4eea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62927
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In MT8186, we need to disable spm_thermal to prevent it from
influencing other wdt status.
There are two hardware pathes which are used for asserting watchdog
from thermal. We can disable status of path 1 because status of
path 2 is used.
1. Thermal -> SPM -> WDT
2. Thermal -> WDT
Spm_thermal (path 1) is a flexible option for software control, and
the hardware designer suggests that we should disable it if we don't
use it.
BUG=none
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I0ffde6bad3000a64e3b5782edaa72c62da034302
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62890
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Because we close external signal in kernel driver since MT8195, it's
more reasonable to trigger sw reset with exteranl signal again
whenever the wdt status is not equal to 0.
BUG=none
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ic6128df7eadaebcf7ff8d4c5492e3e0cfbab6e36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62797
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable SBU orientation handling by SoC for both USBC port0 and USBC
port1. Nivviks USBC port0 do not have retimer, USBC port1 has redriver,
but that do not flip the data lines. Hence we need to set bits for both
the USBC ports.
BRANCH:None
TEST=emerge-nissa coreboot chromeos-bootimage. Flash the image on
nivviks board and verified USBC display is working on both the ports in
normal and inverted connections.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I219de6092ac9a9c773adbaa99f5a7d6196a2c937
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62731
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Without setting the set_resources field for soc_ops, we will get an
error during device initialization:
[ERROR] CPU_CLUSTER: 0 missing set_resources
Because the set_resources field is considered mandatory, explicitly set
it as no-op noop_set_resources.
BUG=b:224419346
TEST=emerge-corsola coreboot
TEST=Did not see the error on krabby
BRANCH=none
Change-Id: Ic82b86f0482a9de09e942c1674be5f0ac615851f
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Add wifi sar for galnat/galnat360
Use SKU ID to load wifi table.
Each Project and SKU ID correspond as below
galtic (sku id:0x120000)
galith (sku id:0x130000)
galnat (sku id:0x140000)*
gallop (sku id:0x150000)
galtic360 (sku id:0x260000)
galith360 (sku id:0x270000)
galnat360 (sku id:0x2B0000)*
BUG=b:222008376
TEST=emerge-dedede coreboot chromeos-bootimage \
coreboot-private-files-baseboard-dedede
verify the SAR table is correct in each project
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I868a7416a002732736cabea48ce80548ea75e517
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Configure GPIOs according to updated schematics.
- GPP_A21 from NC to TCP_DP1_CTRLCLK.
- GPP_A22 from NC to TCP_DP1_CTRLDATA.
- GPP_E22 from DDIA_DP_CTRLCLK to NC.
- GPP_E23 from DDIA_DP_CTRLDATA to NC.
BUG=b:214025396
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I9d2d73820fbb191b682713e4e351c6375927ddf4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This sets EPP value to be 45% for all Adl RVP variants.
Historically, EPP Ratio has always been 50% (128) on Chrome platforms.
But on Intel Alderlake EPP ratio of 45% is recommended for optimal
power and performance on Chrome platforms.
TEST=
Use 'iotools rdmsr [cpu id] 0x774' command and check field 32:24 = 0x73.
Signed-off-by: Cliff Huang <cliff.huang@intel.corp-partner.google.com>
Change-Id: If83a2148d596efccd2e50cc82f1afcbfb9ebb935
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
This patch is adding support for Cirrus Logic CS35l41/CS35l53
smart amplifier. This part is now used in number of new chromebook's
HW designs by several vendors.
This driver uses the ACPI Device Property interface to generate
the required parameters into the _DSD table format expected by
the kernel. For detailed information about these properties, please
check Linux kernel documentation:
/Documentation/devicetree/bindings/sound/cirrus,cs35l41.yaml
Change-Id: I2cbb1cef89f8d56ee73fab06c68933a2ab8c3606
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This reverts a change that was causing hangs and exceptions during boot
on an ADL brya4es.
The hang (or APIC exception) occurs at what appears to be the FSP MP
initialization sequence, prior to the "Display FSP Version Info HOB"
log being displayed :
[DEBUG] Detected 10 core, 12 thread CPU.
[DEBUG] Display FSP Version Info HOB
This reverts commit 40ca79714a.
BUG=b:224873032
TEST=`emerge-brya coreboot chromeos-bootimage`, flash and verify brya4es
is able to successfully reboot 200 times without any issues.
Change-Id: I88c15a51c5d27fbd243478c923e75962d3f8d67d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This message is not really an error message, so BIOS_ERR is
inappropriate. The message does seem more like a warning though,
that the developer could have multiple Kconfigs selected to send EOP,
therefore switch to BIOS_WARN instead.
BRANCH=firmware-brya-14505.B
TEST=build
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I57a34334007a6a7443302c2f25de3d5c87c85573
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
TCSS ASL code was carried forward from TGL and it used to follow the same
sequence.
Recently as part of s0ix hang issue, it was found that sending IOM
MCTP command as part of TCSS D3 Cold enter-exit sequence created an
issue.
We discovered that due to change in hardware sequence, ADL should not
set/reset IOM MCTP during D3 cold entry or exit. This patch removes the
bit setting from ASL file to prevent hang in the system.
This patch also removes obsolete Pcode mailbox communication which is
no longer required for ADL.
BUG=b:220796339
BRANCH=firmware-brya-14505.B
TEST=Check if hang issue is resolved with the CL and no other regression
observed
Change-Id: I2f066bcc4a8f475a15ddd12ef5ed87d7298312bb
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62861
Reviewed-by: Shobhit Srivastava <shobhit.srivastava@intel.corp-partner.google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The coreboot toolchain is a huge blob and increases the size of the
build a lot. If needed, the specific toolchain can be added before
building the ISO or with `nix-shell` later in the live system, as shown
below.
$ nix-shell -p coreboot-toolchain.i386
Thus, remove this from the todo list.
Change-Id: Ia24ceb84f202828f1c97d3ba5bafbf6af0361bdb
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This was to merge PCIe ACPI code to WWAN device. But, now use recent
_DSD generation changes in FM driver instead. PCie generic driver is
not used for WWAN at this time.
Also, RTD3 devices are moved to overridetree.cb where WWAN is
present.
BUG=b:221250331
BRANCH=firmware-brya-14505.B
TEST=
Check that _DSD is added to WWAN device in SSDT for the variants.
Check that RTD3 is added to WWAN device in SSDT for the variants.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ia343c7545cf30bdbcd1de19e5eb84049dbb2977f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch refactors the current P2SB common code driver to accommodate
the future SoC platform with provision of more than one P2SB IP in
disaggregated die architecture.
IA SoC has only one P2SB in PCH die between SKL to ADL. Starting with
MTL, one more P2SB IP resides in IOE die along with SoC die. (PCH die is
renamed as SoC in MTL.)
P2SB library (p2sblib.c) is common between PCH/SoC and IOE, and p2sb.c
is added only for PCH/SoC P2SB.
BUG=b:224325352
TEST=Able to build and boot brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib671d9acbfdc61305ebb401499bfc4742b738ffb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change supports the configuration and enablement of
mdp clock to vote for turbo and supports different display
panel resolutions and framerates.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Change-Id: Ibf4f11d02b0edf83461dbb7af99fda5f33cd5b71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62371
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for EDP (Embedded DisplayPort) clocks in coreboot.
This change supports the configuration and enablement of
EDP PIXEL, LINK, LINK_INTF and AUX clocks.
BUG=b:182963902,b:216687885
TEST=Validated on qualcomm sc7280 development board.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Change-Id: Ia6872ede515401e95ea2dadc9766e3e70fb66144
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59611
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, many Linux drivers use DMI quirks to identify ChromeOS
devices and handle them accordingly: namely they look for the SMBIOS
system manufactuer to be "GOOGLE" or "Google", and the bios-vendor to be
coreboot. Historically this was consistently the case, but recent model
ChromeOS devices allow the OEM to set the mainboard manufacturer, which
is also the default system manufacturer. This breaks many DMI quirks,
notably ones used by SOF (sound open firmware) for audio.
To fix this, set the system manufactuer for ChromeOS devices to "Google"
for devices selecting CONFIG_EC_GOOGLE_CHROMEEC_SKUID, leaving the OEM
customization in place for the mainboard manufacturer. Since boards
selecting CONFIG_EC_GOOGLE_CHROMEEC_SKUID are the only ones overriding
the default mainboard manufacturer, they are the only ones which need
this correction.
Test: build/boot google/bloog with Linux 5.16, verify SOF drivers
correctly detect device as a Chromebook and load the appropriate
audio firmware.
Change-Id: I9de17fa12689ab4e627b995818aa3d2653102b04
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62796
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Cache the BIOS region and extended BIOS region if the boot device is
memory mapped, which is mostly the case with Intel SoC platform.
Having the ROM region cached helped to improve the pre-boot time.
TEST=Able to boot redrix to Chrome OS without seeing any sluggishness.
Additionally verified on EHL board (from siemens), shows significant
savings in payload loading time as below:
Here is the timestamp snippet showing the payload load time as a
comparison between current upstream and the patched version:
upstream:
90:starting to load payload 1,072,459 (1,802)
958:calling FspNotify(ReadyToBoot) 12,818,079 (11,745,619)
with this patch:
90:starting to load payload 1,072,663 (2,627)
958:calling FspNotify(ReadyToBoot) 5,299,535 (4,226,871)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I02b80eefbb3b19331698a205251a0c4d17be534c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch provides a way to cache `ext_bios` region for all stages to
save boot time.
TEST=Able to see the ext_bios region in MTRR snapshot when cached on
the Brya variants.
Here is the timestamp snippet showing the payload load time as a
comparison between current upstream and the patched version:
upstream:
90:starting to load payload 1,072,459 (1,802)
958:calling FspNotify(ReadyToBoot) 12,818,079 (11,745,619)
with this patch:
90:starting to load payload 1,072,663 (2,627)
958:calling FspNotify(ReadyToBoot) 5,299,535 (4,226,871)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I87139a9ed7eb9ed43164a5199aa436dd1219145c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch cleans up `efi_datatype.h` to allow other SoC and/or driver
code to use this file.
`PiPei.h` file only gets added from UDK2017 hence, the platform with the
older EDK2 base (prior to UDK2017) is unable to resolve this file
dependency.
This CL removed the `PiPei.h` header and only added the required header
file `PiPeiCis.h` for platforms with UDK base >= 2017.
BUG=b:200113959
TEST=Able to build Brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie9177814fcf41e5950ace94050356f0273f765c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
As per ME BWG, the patch retries MEI CSE DISABLE command if CSE doesn't
respond or sends the garbled response. It retries the command
additionally 2 more times.
TEST=build and boot the Brya board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Id38a172d670a0cd44643744f27b85ca7e368ccdb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
As per ME BWG, the patch retries END_OF_POST command if CSE doesn't
respond or sends the garbled response. It retries the command
additionally 2 more times.
BUG=b:200251277
TEST=Verify EOP retry mechanism for brya board.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ieaec4d5564e3d962c1cc866351e9e7eaa8e58683
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Remove global variable and use 'pcidev_path_on_root()' to get the base
address of PCIe controller.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Ia41c82a7aa5d6e9d936e242550851cef83afeae9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add chip config for setting PCIe config.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Icff83f2a9f76862065987a74cfcc7e511be80a20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The current SMM framework only allows the mainboard code to handle GPEs.
i.e., Events 0 - 23. This change allows the mainboard code to handle any
SMI events not handled by the SoC code. This will allow the mainboard
code to handle `SMITYPE_ESPI_SMI`.
BUG=b:222694093
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I81943e8cb31e998f29cc60b565d3ca0a8dfe9cb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Rename `BOARD_HP_SNB_IVB_LAPTOPS` to `BOARD_HP_SNB_IVB_LAPTOPS_COMMON`
to indicate and to make it clear that this option serves as base for
others.
Built HP EliteBook Revolve 810 G1 with BUILD_TIMELESS=1 and also with
`INCLUDE_CONFIG_FILE` disabled. coreboot.rom remains identical.
Change-Id: Icadeb8a33ae0787d2cd5da460065a2ed15256d64
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch introduces CONFIG_I2C_TRANSFER_TIMEOUT_US,
which controls how long to wait for an I2C devices to
produce/accept all the data bytes in a single transfer.
(The device can delay transfer by stretching the clock of
the ack bit.)
The default value of this new setting is 500ms. Existing
code had timeouts anywhere from tens of milliseconds to a
full second beween various drivers. Drivers can still have
their own shorter timeouts for setup/communication with the
I2C host controller (as opposed to transactions with I2C
devices on the bus.)
In general, the timeout is not meant to be reached except in
situations where there is already serious problem with the
boot, and serves to make sure that some useful diagnostic
output is produced on the console.
Change-Id: I6423122f32aad1dbcee0bfe240cdaa8cb512791f
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
C1-state auto demotion feature allows hardware to determine C1-state as
per platform policy. Since Brya sets performance policy to balanced from
hardware, auto demotion can be disabled without performance impact.
Also, disabling this feature results in 110 mW power savings during
video playback.
Note that C1state Autodemotion feature is not applicable for ADL-P SoC.
Hence recommendation is to keep it disabled.
BUG=b:221876248
BRANCH=firmware-brya-14505.B
TEST=Code compiles and correct value of c1-state auto demotion is passed
to FSP. Also power and performance impact has been measure by respective
teams.
Change-Id: I41eea916cdfe4a86e4d263e3191f5cb40fa33a90
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
FSP has a parameter to enable/disable c1-state autodemotion feature.
Boards/Baseboard can choose to use this feature as per requirement.
This patch hooks up this parameter to devicetree
BUG=b:221876248
BRANCH=firmware-brya-14505.B
TEST=Check code compiles and correct value has been passed to FSP.
Change-Id: I2d7839d8fecd7b5403f52f3926d1d0bc06728ed9
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
coreboot chip.h files mainly contains variable which allows board to
fill platform configuration through devicetree.
Since many of this configuration involves FSP UPDs, variable names were
in camel case which aligned with UPD naming convention.
By default coreboot follow snake case variable naming, so cleaning up
file to align all variable names as per coreboot convention.
During renaming process, this patch also removes unused variables
listed below:
-> SataEnable // Checked in SoC code based on PCI dev enabled status
-> ITbtConnectTopologyTimeoutInMs // SoC always passes 0, so not used
Note: Since separating out changes into smaller CL might break the
compilation for the patch set, this is being pushed as a single big CL.
BUG=None
BRANCH=firmware-brya-14505.B
TEST=All boards using ADL SoC compiles with the CL.
Change-Id: Ieda567a89ec9287e3d988d489f3b3769dffcf9e0
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Commit hash b8b40964 ( mb, soc: Add the SPD_CACHE_ENABLE) introduced
per mainboard logic to invalidate the mrc_cache.
This patch moves mrc_cache invalidating logic into IA common code and
cleans up the code to remove unused argument `dimms_changed` from SoC
and mainboard directory.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6f18e18adc6572571871dd6da1698186e4e3d671
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
This patch adds `FSPM_UPD *` as argument for
mem_populate_channel_data() and read_spd_dimm().
This change will help to update the architectural FSP-M UPDs in
read_spd_dimm().
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I770cfd05194c33e11f98f95c5b93157b0ead70c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
This patch modifies `memcfg_init` and `variant_memory_init`functions
argument from FSP_M_CONFIG to FSPM_UPD.
This change in `memcfg_init()` argument will help to update the
architectural FSP-M UPDs from common code blocks rather than going
into SoC and/or mainboard implementation.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3002dd5c2f3703de41f38512976296f63e54d0c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Hoglin and Herobrine (proto1) should share majority of GPIOs.
Conslidating the QUP initializations in mainboard. Also, putting
fingerprint init in a conditional as not all devices will have an FP
sensor.
BUG=b:182963902,b:223826899
BRANCH=None
TEST=booted BIOS on hoglin and check for i2c errors in dmesg
Change-Id: I48ce42760f2c75f04619b967a05909d2b3f28e2c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Currently the BayHub eMMC enable pin is using the default
configuration from the baseboard, which leads to RTD3 not being able
to control the GPIO when exiting and entering suspend. To fix this,
program the GPIO in the ramstage GPIO table.
BUG=b:222436260
TEST=USE="project_primus" emerge-brya coreboot chromeos-bootimage
scope enable pin while performing suspend stress and enable pin
works as expected.
test suspend stress 1000 cycles passed on primus.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I1b6f164cc326bd368addb1e143ad2cbd449bb08d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
DDR4 SPD data needs to be 512 byte to comply with the spec.
Though there is no vital timing data used beyond 256 byte there are some
part information which will be used to show the part info in the
coreboot log. If the buffer is too small this log shows garbage.
This patch increases the SPD buffer size from 256 byte to 512 to avoid
side effects.
Change-Id: I5b88df7818cfd62b3579d69f9f5bb14880f49c8c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The patch implements error handling as per the ME BWG guide. The BWG
recommends HECI interface reset if there is a timeout or malformed
response is received from the CSE. Also, the patch triggers HECI
interface reset if the CSE link state is not ready in the heci_send()
API.
TEST=Verify HECI Interface reset in the simulated error scenarios.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I3e4a97800cbc5d95b8fd259e6e34a32fc82d8563
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The patch implements below changes:
1. Implements different error codes and use them in appropriate
failure scenarios of below functions:
a. heci_send()
b. recv_one_message()
c. heci_receive()
2. As heci_send_receive() is updated to return appropriate error codes
in different error scenarios of sending and receiving the HECI
commands. As the function is updated to return 0 when success, and
non-zero values in the failure scenarios, so all caller function have
been updated.
BUG=b:220652101
TEST=Verified CSE RX and TX APIs return error codes appropriately in
the simulated error scenarios.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ibedee748ed6d81436c6b125f2eb2722be3f5f8f0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The verstage.c file contains PSP verstage specific code. We don't need
it when using x86 verstage.
BUG=b:193050286
TEST=Build and boot guybrush with x86 verstage
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6dc928cdce0c922bb18f4479b993c89dff106070
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62740
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This sets EPP value to be 45% for all Brya variants.
Historically, EPP Ratio has always been 50% (128) on Chrome platforms.
But on Intel Alderlake EPP ratio of 45% is recommended for optimal
power and performance on Chrome platforms.
BUG=b:219785001
BRANCH=firmware-brya-14505.B
TEST=
Use 'iotools rdmsr [cpu id] 0x774' command and check field 32:24 = 0x73.
Signed-off-by: Cliff Huang <cliff.huang@intel.corp-partner.google.com>
Change-Id: I973cfec72a0be24c56c4cd3283d2fe6e18400d02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update PL1, PL2, and temperature sensor values from thermal team,
as well as, we remove unused temperature sensors according to
baseboard/devicetree.cb and mainboard schematic. After we check
DTT setting, the thermal and performance test pass.
BRANCH=dedede
BUG=b:204229229
TEST=on beadrix, run following commands:
localhost /tmp # cat /sys/class/thermal/thermal_zone*/type
x86_pkg_temp
INT3400 Thermal
TSR0
TSR1
TCPU
localhost /tmp # cat /sys/class/thermal/thermal_zone*/temp
45000
20000
32800
32800
39000
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: Ibc59c4aa431f600158e744f5bbdc6d59a07a1ef3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62729
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GFX HDA is the audio controller that provides audio output via the
external display connection, ACP is the audio coporcessor for the on-
board audio codec and XHCI2 is the third XHCI controller that provides
one USB 2.0 port. All those devices are used, so enable them in the
board's devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I186797a832470eb17752e06aa2fcc0b5c9db0398
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62571
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable pen garage. Pen detect is active low. And wake system when
eject.
BUG=b:223476974
TEST=evtest work as expected.
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "PRP0001:00"
Supported events:
Event type 0 (EV_SYN)
Event type 5 (EV_SW)
Event code 15 (SW_PEN_INSERTED) state 0
Properties:
Testing ... (interrupt to exit)
Event: type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: -------------- SYN_REPORT ------------
Event: type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I2f676301c3372a4760853ce9c10b75f94e22bbcd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This change mostly changes links that were identified as broken by
the 'website_scans' jenkins job.
There were some links that seem to be up at times, but that are
identified by link-checker as broken because of SSL issues.
At least one other link was changed to point to archive.org so
that it doesn't break at some point in the future. We should
probably try to make sure that everything is archived there and
point to those versions when possible.
There are still lots more links to do.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I36868ddf6113e18fa6841427dd635c75445b7bef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Only one ACPI device should be added to a PCIe root port. For the root
ports which already have device created, the generated code from this
driver needs to be merged with the existing device.
By default, this driver will create new device named DEV0.
This change allows to generate code under an existing device.
ex: (generate code under PXSX):
Scope (\_SB.PCI0.RP01.PXSX)
{
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package (0x01)
{
Package (0x02)
{
"UntrustedDevice",
One
}
}
})
}
BUG=b:221250331
BRANCH=firmware-brya-14505.B
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I80634bbfc2927f26f2a55a9c244eca517c437079
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Since the new loglevel markers were added, there will now be a marker
character at the beginning of the coreboot banner string, and this will
make the existing regular expressions meant to find it fail to match.
This patch fixes the problem by just allowing for a single extra
character there (any character to avoid the hassle of having to match
the marker explicitly). The extra character is optional so that we will
still continue to match banners from older versions of coreboot as well.
Since the `?` glyph is not available in basic POSIX regular expressions,
we have to switch to REG_EXTENDED syntax (should otherwise make no
difference). (Also, move side effects out of assert() while I'm here,
that's not actually safe for the standard libc implementation.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I99fb347eb1cf7b043a2113dfda7c798d6ee38975
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62720
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Get boot performance timestamps from CSE and inject them into CBMEM
timestamp table after normalizing to the zero-point value. Although
consumer CSE sku also supports this feature, it was validated on
CSE Lite sku only.
BUG=b:182575295
TEST=Able to see TS elapse prior to IA reset on Brya/Redrix
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 88,000
945:CSE started to handle ICC configuration 88,000 (0)
946:CSE sent 'Host BIOS Prep Done' to PMC 90,000 (2,000)
947:CSE received 'CPU Reset Done Ack sent' from PMC 282,000 (192,000)
0:1st timestamp 330,857 (48,857)
11:start of bootblock 341,811 (10,953)
12:end of bootblock 349,299 (7,487)
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Idcdbb69538ca2977cd97ce1ef9b211ff6510a3f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
In order to copy the PSP verstage logs into x86 cbmem, we need to enable
DEBUG_SMI. This will include the CBMEM console code in SMM. I only
enable DEBUG_SMI when UART is disabled because SMM doesn't currently
save/restore the UART registers. This will result in clearing the
interrupt enable bits and makes it so you can no longer use the TTY.
BUG=b:221231786, b:217968734
BRANCH=guybrush
TEST=Build serial and non serial firmware and verify DEBUG_SMI is set
correctly.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I85a7933e8eb49ff920d00e43a494aaeab555ef3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Now that SMM can write to CBMEM we can simply replay the transfer buffer
cbmem console to move it into the main cbmem console.
replay_transfer_buffer_cbmemc() relies on the EARLY_RAM linker symbols.
Since the SMM rmodule get linked with a different linker script than
bootblock/romstage it doesn't have access to these symbols. In order to
pass these symbols into SMM, we parse the bootblock.map file and
generate an early_ram.ld script. This script is then used when linking
SMM.
I replay the buffer in `smm_soc_early_init` because this call happens
before `console_init()`. `console_init()` prints the SMM header and we
want to append the verstage contents before printing the header to avoid
confusion.
BUG=b:221231786
TEST=Perform S0i3 cycles and verify PSP verstage logs now show up when
doing `cbmem -c`.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I64d33ccdee9863270cfbcaef5d7c614349bd895c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change provides hooks for the SoC so it can perform any
initialization and cleanup in the SMM handler.
For example, if we have a UART enabled firmware with DEBUG_SMI, the UART
controller could have been powered off by the OS. In this case we need
to power on the UART when entering SMM, and then power it off before we
exit. If the OS had the UART enabled when entering SMM, we should
snapshot the UART register state, and restore it on exit. Otherwise we
risk clearing some interrupt enable bits.
BUG=b:221231786, b:217968734
TEST=Build test guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I946619cd62a974a98c575a92943b43ea639fc329
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Enable PCIe support for mt8195.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: I314572955f1021abe9f2f0f4635670135ed08fff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add a new function 'mtk_pcie_pre_init' to assert the PCIe reset at early
stage to reduce the impact of 100ms delay.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: If6799c53b03a33be91157ea088d829beb4272976
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Log the platform boot mode reported by PSP verstage to PSP stage 1
bootloader. This helps to improve the debuggability.
BUG=b:193050286
TEST=Build and Boot to OS in Nipperkin. Ensure that the platform boot
mode is logged in the verstage logs.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I752ee56f2af48215a770d799432d02f0609757cd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
GPIO_18 is used for LCD_PRIVACY_SCREEN feature starting board phase 2.
But it is programmed incorrectly in the concerned ACPI device. Pass the
correct GPIO.
BUG=b:204401306
TEST=Build and boot to OS in Nipperkin. Ensure that the ACPI object
contains the right GPIO. Ensure that the screen visibility gets updated
by pressing the privacy screen button.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I99d40b49f4e97063f1ec2e15ac3da21f700a93eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
As part of boot time optimization, one of the culprit was CSE where
response to End Of Post (EOP) command used to take ~60ms. Earlier patch
was pushed to delay the EOP to reduce response time to ~5-7 ms. During
this stage overall platform boot time was ~1.15 seconds.
Once boot time was optimized to ~ 1 seconds, CSE EOP time again
increased to ~80 ms since coreboot used to send EOP at the time where
CSE was busy. This created some back and forth moving of sending EOP
command function within coreboot sequence.
Upon debugging using traces, it was found that coreboot used to send
EOP late where CSE was busy loading other IP payload, so it might take
more time to respond.
In order to avoid delayed response, coreboot has to send EOP in
stage when CSE is done with firmware init and it will be ready to
serve EOP as soon as possible. This also aligns with previous flow where
FSP used to send EOP once silicon init is done and coreboot used to
rely on FSP to send this message.
Moving EOP to earlier stage (From SoC) meets the requirement and CSE EOP time
reduces from ~60 ms to ~20 ms on Brya board.
Note that once SoC code sends EOP, coreboot common code won't send it
again since common code already has check in case EOP is sent earlier.
BUG=b:211085685
BRANCH=firmware-brya-14505.B
TEST=Tested on Brya system before and after the changes. Observed ~40ms
savings in boot time.
Change-Id: I9401d5e36ad43cdc0dfe947aabc82528d824df9b
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Earlier while trying to optimize boot time End Of Post (EOP) time kept
increasing (~80 ms) when boot time decreased to around 1 second.
This was because CSE was busy with own firmware loading.
When EOP was moved later in boot stage it again created issue since CSE
got busy with other payload loading for OS boot, so response to EOP
got delayed by ~70-80 ms.
In order to avoid delayed response, coreboot has to send EOP in
stage when CSE is done with firmware init and it will be ready to
serve EOP as soon as possible. This also aligns with previous flow
where FSP used to send EOP once silicon init is done and coreboot used
to rely on FSP to send this message.
Moving EOP to BS_DEV_INIT boot state meets this requirement and CSE EOP
time reduces from ~60 ms to ~20 ms on Brya QS board.
Since this setting might vary for each SoC, SoCs can decide when to send
EOP in the boot sequence. This patch adds Kconfig option to send EOP via
SoC
BUG=b:211085685
BRANCH=firmware-brya-14505.B
TEST=Code compilation is fine for Brya board. Boot time test is done
using entire patchset and EOP time is reduced to ~25ms from earlier ~80ms.
Change-Id: I9c7fe6f8f3fadb68310d4a09692f51f82c737c35
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
The current code will write the raw value from the CMOS, which doesn't
match the respective setting in EC.
Switch argument will write the correct value, and prevent the setting
being reset.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I40dc78c743f4201a11ea0c26a8af716cab42b805
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The current code will write the raw value from the CMOS, which doesn't
match the respective setting in EC.
Switch argument will write the correct value, and prevent the setting
being reset.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I93444cdb96eaf729630b48551d0853511b584634
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The current code will write the raw value from the CMOS, which doesn't
match the respective setting in EC.
Switch argument will write the correct value, and prevent the setting
being reset.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iabeec47bf492b698f95d86aa2d08ba9caedd75f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This solved the error:
i801_smbus 0000:00:1f.1: can't derive routing for PCI INT A
i801_smbus 0000:00:1f.1: PCI INT A: not connected
i801_smbus 0000:00:1f.1: SPD Write Disable is set
i801_smbus 0000:00:1f.1: SMBus using polling
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Idebd581b7ed6d193d83340b7dc94248df43525c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The mainboard may not be able to disable the internal cap, so we want
to set 0xe0 for all boards to minimize the internal cap. And a
mainboard implementation may choose XTAL with higher cload if the
frequency requirement is met, and the total capacitance can be tuned
externally for different boards.
BUG=b:218439447
TEST=set capid to 0xe0.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I2139e6b3456d7a50e3cdc8fc606e5f6ea3406044
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62563
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some non-SoC code might want to know whether or not the CNVi DDR RFIM
feature is enabled. Also note that future SoCs may also support this
feature. To make the CnviDdrRfim property generic, move it from
soc/intel/alderlake to drivers/wifi/generic instead.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Idf9fba0a79d1f431269be5851b026ed966600160
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Currently, all of the commands for building futility are printed as they
are run. This change skips printing the check for libcrypto unless the
check actually fails. This prevents the error from being displayed when
there isn't actually a problem.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I9ef36c0b64f7cd69d19b8faabd165ef6651c838e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
While running Sphinx, it shows the warning "document isn't included in
any toctree" for the documents checklist.md and templates.md. These are
not meant to be listed in ToC trees.
Thus, mark them as orphaned to exclude them from ToC trees.
Change-Id: I1ff8f7c24ac9b3c3a120914c0c72ab73e85c4873
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62584
Reviewed-by: Thomas Heijligen <src@posteo.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set NOR pin drive to 8mA to comply with HW requirement.
This implementation is according to chapter 5.1, 5.6 and 5.8 in MT8186
Functional Specification.
BUG=b:218775654, b:216462313, b:212375511
TEST=SPI SI tests for AP to NOR pass for both kingler and krabby.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I5b6e37b0f7d4207ea35f11394d25ad1e096ac01a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add GPIO driving functions to adjust pin driving.
The value of drive strength is different for each SoC, so we define
GPIO_DRV0 to GPIO_DRV7 which are corresponding to 2/4/6/8/10/12/14/16mA
in MT8186.
This implementation is according to chapter 5.1 in MT8186 Functional
Specification.
BUG=b:218775654, b:216462313, b:212375511
TEST=build pass
Signed-off-by: Guodong Liu <guodong.liu@mediatek.corp-partner.google.com>
Change-Id: I6d987f28be98b515fa5c542222bda08bea1d5118
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62471
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix stylus UI behavior bug.
1) it appears the kernel's gpio_key driver is not expecting
an IRQ descriptor for the `gpio` property, therefore change
to an active-low input.
2) The wakeup event was configured backwards.
Change list
- Configure GPP_A7 as "ACPI_GPIO_INPUT_ACTIVE_LOW".
- Change wakeup_event_action from ASSERTED to DEASSERTED.
BUG=b:220992812
TEST=emerge-brya coreboot chromeos-bootimage and verify pass
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I6f5e2992584d759eb1a559684d1cda08c7cbe3f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change will allow the SMI handler to write to the cbmem console
buffer. Normally SMIs can only be debugged using some kind of serial
port (UART). By storing the SMI logs into cbmem we can debug SMIs using
`cbmem -1`. Now that these logs are available to the OS we could also
verify there were no errors in the SMI handler.
Since SMM can write to all of DRAM, we can't trust any pointers
provided by cbmem after the OS has booted. For this reason we store the
cbmem console pointer as part of the SMM runtime parameters. The cbmem
console is implemented as a circular buffer so it will never write
outside of this area.
BUG=b:221231786
TEST=Boot non-serial FW with DEBUG_SMI and verified SMI messages are
visible when running `cbmem -1`. Perform a suspend/resume cycle and
verify new SMI events are written to the cbmem console log.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia1e310a12ca2f54210ccfaee58807cb808cfff79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Nissa boards are curretly using chromeos.fmd file of brya. The SPI flash
layout for brya is of 32MB size, and nissa is expected to have 16MB SPI
NOR flash. The current composition of AP firmware exceeds 16MB. To get
an estimate of the unutilized region in the current flash layout for
nissa, added RW_UNUSED regions. The idea is to reduce the AP firmware
size to under 16MB and to remove the RW_UNUSED regions from the final
fmd file.
Below table gives the size reduction from brya fmd to nissa fmd:
+----------------+-------------------+---------------+
| Region | Earlier size (KB) | New size (KB) |
+================+===================+===============+
| SI_ME | 5116 | 3772 |
+----------------+-------------------+---------------+
| RW_SECTION_A/B | 8192 | 4344 |
+----------------+-------------------+---------------+
| VBLOCK_A/B | 64 | 8 |
+----------------+-------------------+---------------+
| ME_RW_A/B* | 3008 | 1434 |
+----------------+-------------------+---------------+
| RW_LEGACY | 2048 | 1024 |
+----------------+-------------------+---------------+
| RW_ELOG | 16 | 4 |
+----------------+-------------------+---------------+
| SHARED_DATA | 8 | 4 |
+----------------+-------------------+---------------+
| VBLOCK_DEV | 8 | 0 |
+----------------+-------------------+---------------+
| RW_SPD_CACHE | 4 | 0 |
+----------------+-------------------+---------------+
| RW_NVRAM | 24 | 8 |
+----------------+-------------------+---------------+
| WP_RO | 8192 | 4096 |
+----------------+-------------------+---------------+
| GBB | 448 | 12 |
+----------------+-------------------+---------------+
*Based on LZMA compression on ME_RW_A/B regions. With LZMA compression,
this region can be 1434K. Without this, ~665K will be more in each of
these regions.
Patch: https://review.coreboot.org/c/coreboot/+/62358/
BUG=b:202783191
BRANCH=None
TEST=Build and boot Nivviks.
Cq-Depend: chrome-internal:4584911
Change-Id: I24b1c19cb71a54fc916a12668f72193f9689e755
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Add SOC_INTEL_CSE_LITE_COMPRESS_ME_RW Kconfig to enable compression on
ME_RW blobs. Select the Kconfig to add LZMA compressed ME_RW blobs to
ME_RW_A/B regions.
On ADL-N, this results in savings of ~665KB in each of ME_RW_A/B
regions.
FMAP REGION: ME_RW_A
Name Offset Type Size Comp
me_rw 0x0 raw 1275246 LZMA
(1957888 decompressed)
(empty) 0x1375c0 null 193056 none
FMAP REGION: ME_RW_B
Name Offset Type Size Comp
me_rw 0x0 raw 1275246 LZMA
(1957888 decompressed)
(empty) 0x1375c0 null 193056 none
Change-Id: I2e31c358b4969b077d65ce6369a877914d573aed
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
With LinuxBoot Linux relied on the legacy method of fetching the RSDP
pointer to get ACPI. This uses a more modern approach available since
2018 on the Linux kernel, which involves filling in the zero page.
This method takes precedence over any other method of fetching the
RSDP in Linux (UEFI, Kexec, Legacy/BIOS). Some UEFI zealots are
threatening that legacy code will be removed from Linux so it's best
to already adapt to that possibility.
Tested on Qemu:
- With qemu the RSDP is always in the EBDA, so checking if Linux uses
the provided pointer is better done with a forced bad entry
- With a fake bad pointer Linux correctly does not find RDSP
Change-Id: I688b94608b03b0177c42d2834c7e3beb802ae686
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The ACPI RSDP can only be found in:
- legacy BIOS region
- via UEFI service
On some systems like ARM that legacy BIOS region is not an option, so
to avoid needing UEFI it makes sense to expose the RSDP via a coreboot
table entry.
This also adds the respective unit test.
Change-Id: I591312a2c48f0cbbb03b2787e4b365e9c932afff
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62573
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If it is not cleared and the number of strings is fewer than last
iteration, the match[3] will keep the last value, which actually
should be empty.
Add assert to make sure the level is a legal value.
BUG=b:222038278
Change-Id: If14e0923fbb1648d83784eb5dc1411c93227db5a
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62482
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
cb_err_t was meant to be used in place of `enum cb_err` in all
situations, but the choice to use a typedef here seems to be
controversial. We should not be arbitrarily using two different
identifiers for the same thing across the codebase, so since there are
no use cases for serializing enum cb_err at the moment (which would be
the primary reason to typedef a fixed-width integer instead), remove
cb_err_t again for now.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Iaec36210d129db26d51f0a105d3de070c03b686b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add PCIe support for MediaTek platform.
Reference:
- MT8195 Register Map V0.3-2, Chapter 3.18 PCIe controller (Page 1250)
- linux/drivers/pci/controller/pcie-mediatek-gen3.c
This code is based on MT8195 platform, but it should be common in each
platform with the same PCIe IP in the future.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Ib9b6adaafa20aeee136372ec9564273f86776da0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
ADL encodes CK cycle time as tCKMin whereas Sabrina encodes WCK cycle
time. Encode tCKMin as per the respective advisories.
BUG=None
TEST=Generate the SPD and ensure that tCKMin is encoded accordingly.
Minimum CAS Latency time is also impacted and is encoded accordingly.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I99ada7ead3a75befb0f934af871eecc060adcb26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Git uses the .mailmap file to map author and committer names and email
addresses to canonical real names and email addresses.
Before adding this file, coreboot shows 1388 different author names and
email addresses because of typos, people changing email addresses, and
spelling their names differently.
After adding the file, the number of authors is down to 1016.
I tried to determine the best email address for each person by looking
at what they'd used most recently, but I can't promise that I correctly
picked the right address for everyone. Please take a look to make
sure that your email address and name is correct.
To enable .mailmap parsing globally, use:
$ git config --global log.mailmap true
To enable it just for a single log, run:
$ git log --use-mailmap
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I1f9b9bccc9322799234475a1cebf9808edd25693
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
This patch aims to make timestamps more consistent in naming,
to follow one pattern. Until now there were many naming patterns:
- TS_START_*/TS_END_*
- TS_BEFORE_*/TS_AFTER_*
- TS_*_START/TS_*_END
This change also aims to indicate, that these timestamps can be used
to create time-ranges, e.g. from TS_BOOTBLOCK_START to TS_BOOTBLOCK_END.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I533e32392224d9b67c37e6a67987b09bf1cf51c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Denverton is a special version of IFD2 flash layout. It defines
10GbE firmware regions (11/12) and the IE (10) region which
other IFD2 platforms do not have. Denverton does not include the
legacy GbE region (3) or the EC region (8) which other IFD2
platforms do have.
TEST='ifdtool -p dnv coreboot.rom' and verify correct output
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Change-Id: I15939ce4672123f39a807d63c13ba7df98c57523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
When entering suspend, ACPI support is disabled by setting OSFG to 0x00.
This has been moved to be the final action, so it is after saving the
current EC settings.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I5705efab42d2fe0fd5abc6c17eeea46ead27db17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set the log level to BIOS_NOTICE for the case where the mainboard can
not provide a MAC address since this can be a valid case. Showing this
message with log level BIOS_ERR is not appropriate.
In addition, rephrase the message to make clear that if the mainboard
does not provide a MAC address the one stored in the MAC will be used.
Change-Id: Ibfc58845f0ea47ced048b446e685c4860a29f075
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Currently the BayHub eMMC controller is only going into its reset
state when the RTD3 sequence is initiated. This causes it to
still consume too much power in suspend states. This CL adds the
power enable GPIO into the RTD3 sequence as well, which will turn
off the eMMC controller (a true D3cold state) during the RTD3
sequence.
BUG=b:222436260
TEST=USE="project_primus" emerge-brya coreboot chromeos-bootimage
test suspend stress 100 cycles passed on primus.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I2fec6a30707fb1a258cdcc73b0ce38252b6f77c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
cr50 firmware revisions starting at 0.5.5 and later are able to extend
their IRQ pulses to be a minimum of 100us long. This change will enable
cr50 long interrupt pulses when it detects the feature is supported by
the detected firmware version. If the capability was detected, then
GPIO PM will be enabled for the device, otherwise it will be disabled.
BUG=b:202246591
TEST=boot brya0, check console logs for the correct message, and
verify the GPIO PM registers.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iaf333dc0f177e17cd03b36ec7e487fc33bde2b93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61722
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This allows mainboards using an I2C bus to communicate with the cr50
to reuse the functionality related to firmware version and BOARD_CFG.
BUG=b:202246591
TEST=boot on brya0, see cr50 FW version in logs
Change-Id: Ide1a7299936193da3cd3d15fdfd1a80994d70da0
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Mainboards accessing the cr50 over an I2C bus may want to reuse some of
the same firmware version and BOARD_CFG logic, therefore refactor this
logic out into a bus-agnostic file, drivers/tpm/cr50.c. This file uses
the new tis_vendor_read/write() functions in order to access the cr50
regardless of the bus which is physically used. In order to leave SPI
devices intact, the tis_vendor_* functions are added to the SPI driver.
BUG=b:202246591
TEST=boot to OS on google/dratini, see the same FW version and board_cfg
console prints as before the change.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie68618cbe026a2b9221f93d0fe41d0b2054e8091
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Windows complains on missing drivers for these ACPI devices. Hide them
from OS as it doesn't influence the hardware operation. Linux can
still probe the drivers correctly.
TEST=Boot Windows 11 and see there are no devices with missing drivers.
Boot Ubuntu 20.04 and check that drivers corresponding to ACPI HIDs are
still probed.
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Change-Id: I6c30c08ab730749bddef7ea67c7470c1554bd572
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
ChromeOS considers the WWAN devices to be untrusted, therefore enable
the new DmaProperty in the WWAN's _DSD to indicate to the OS that these
devices should have IOMMU restrictions applied to them.
BUG=b:215424986
BRANCH=brya
TEST=dump SSDT
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I9c9e73b7ea0575ab87cc980fb4786338047155de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Commit ebf14826
[mb/google/hatch/var/jinlon: Switch to using device pointers]
broke jinlon boards without an electronic privacy screen (EPS) by
disabling the parent device (iGPU) instead of the EPS when determined to
be not present via SKU ID.
Commit c5a3a4a6
[mb/google/hatch (baseboard): add ACPI backlight support]
broke EPS detection by adding a duplicate iGPU device to the devicetree,
resulting in the EPS entry being skipped.
Fix both of these issues by assigning the device alias to the EPS child
device, not the parent (iGPU). Rename the alias for clarity, and combine
the duplicate device definitions for the iGPU.
Test: build/boot google/jinlon SKU w/o EPS, observe GPU functional
in both firmware boot screens and Linux OS.
Change-Id: I0615ce361497abe6872085b0dec83292607e53dd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62593
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 017b5c453a
[ec/google/chromeec/acpi: Rename EC_ENABLE_TABLET_EVENT config]
broke tablet mode on google/caroline and cave in mainline Linux kernels
by changing the inclusion of the ChromeEC tablet mode ACPI handler. Fix
this by addding it back (using the updated name guarding the inclusion
of the tmbc ACPI).
Test: build/boot google/cave under Linux 5.16, observe tablet mode
handled correctly.
Change-Id: Ie0ae5b6a61f104b5e973383344d289cc2e2a7b8d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change is to move MPTS (Mainboard Prepare To Sleep) method from
wwan_power.asl to SSDT.
MPTS is mainboard-specific method, while wwan_power.asl is meant for
WWAN from its name.
Having fixed MPTS method (i.e. DSDT) can not cover the case where device
only presents and certain CBI bit(s) is(are) set.
In Redrix and Brya, there are SKUs with or without 5G, 4G device. For
those with 4G, MPTS method should be different. For those with no WWAN
device, no MPTS is needed.
Having MPTS generating in SSDT also eliminates the need for introducing
Kconfig flags to support different devices in the future.
MPTS method is created inside mainboard_fill_ssdt function in which the
corresponding variant function is called.
This will generate the following for the mainboard:
Scope (\_SB)
{
Method (MPTS, 1, Serialized)
{
Local0 = \_SB.PCI0.RP01.RTD3._STA ()
If ((Local0 == One))
{
\_SB.PCI0.RP01.PXSX.DPTS (Arg0)
}
}
}
Test:
Check the SSDT for MPTS method under \_SB after boot to OS
Use shutdown command and check the GPIO pins from logical analyzer
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I0f0b7638e90a7862173fca99305398bb250373e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Shorten define names containing PCI_{DEVICE,VENDOR}_ID_ with
PCI_{DID,VID}_ using the commands below, which also take care of some
spacing issues. An additional clean up of pci_ids.h is done in
CB:61531.
Used commands:
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]\{2\}\([_0-9A-Za-z]\{8\}\)*[_0-9A-Za-z]\{0,5\}\)\t/PCI_\1ID_\3\t\t/g'
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]*\)/PCI_\1ID_\3/g'
Change-Id: If9027700f53b6d0d3964c26a41a1f9b8f62be178
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
coreboot recently introduced non-printable loglevel markers in the CBMEM
console. Payloads were generally unaffected since they don't use log
levels and it is still legal to append lines without a marker to the
log. However, payloads using cbmem_console_snapshot() to display
existing logs from coreboot have started seeing '?' characters in place
of the markers. This patch fixes the issue by filtering out marker
characters.
BUG=b:221909874
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I4a9e5d464508320cf43ea572d62896d38c2a128d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
SMMSTORE needs to have 64k size (minimum) and have 64k alignment as
enforced by asserts added in commit 1ba6049
[drivers/smmstore/store.c: Add static assertion based on fmap].
Adjust size and alignment of SMMSTORE region in FMAP to ensure those conditions are met.
Test: build google/morphius without asserts being tripped for above conditions.
Change-Id: Ied04e93379e1507f5e6b2a1b71e4098a4561e5d8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The Infineon TPM 1.2 used on glados boards doesn't use a PIRQ;
Linux only works with 'tpm.tis_interrupts=0" and Windows fails to
init the TPM citing a lack of available resources. With the PIRQ
removed, both Linux and Windows are happy / the TPM is available
for use.
Test: build/boot Linux 5.16.x and Windows 11 on google/chell
Change-Id: I544695505291bbebe062df636cc8ddd139c08c2b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
In the northbridge's and root complex' read_resources function, the
GNB IOAPIC resource used MMIO base address of the GNB IOAPIC as index
which might be misleading. Instead use idx++ as a unique index for this
resource.
TEST=Resource allocator doesn't complain and no related warnings or
errors in dmesg. The update_constraints console output changes like
expected:
Before: PCI: 00:00.0 fec01000 base fec01000 limit fec01fff mem (fixed)
After: PCI: 00:00.0 0d base fec01000 limit fec01fff mem (fixed)
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8061364879d772469882fc060f92676de6f600a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
In the northbridge's and root complex' read_resources function, the
mmconf resource used the number of the MMIO_CONF_BASE MSR as index which
might be misleading. Instead use idx++ as a unique index for this
resource.
TEST=Resource allocator doesn't complain and no related warnings or
errors in dmesg. The update_constraints console output changes like
expected:
Before: PCI: 00:00.0 c0010058 base f8000000 limit fbffffff mem (fixed)
After: PCI: 00:00.0 06 base f8000000 limit fbffffff mem (fixed)
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id66c6153fad86bed36db7bd2455075f4a0850750
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
TPM1_MODE and TPM2_MODE defines have to be added to vboot and payload
cflags to make them build correctly without requiring payloads to provide
defines.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I567a9f04d7089699840dc7e0a063cf3030fb934b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Generate the PPKG object in the generate_cpu_entries function instead of
generating the PCNT object that is the used in the PPKG method in
cpu.asl to provide the PPKG object. This both simplifies the code and
aligns Stoneyridge with the other AMD SoCs. This will also make the code
behave correctly in a case where the number of CPU cores/threads isn't a
power of two.
TEST=None, but equivalent change on Picasso was verified to not break
anything on Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib42d718102151a72a5fe812e83eb2eb4f9e7b611
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Generate the PPKG object in the generate_cpu_entries function instead of
generating the PCNT object that is the used in the PPKG method in
cpu.asl to provide the PPKG object. This both simplifies the code and
aligns Picasso with Cezanne and Sabrina. This will also make the code
behave correctly in a case where the number of CPU cores/threads isn't a
power of two.
TEST=Mandolin still boots successfully to Linux desktop and dmesg
doesn't show any any possibly related problems.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifb84435345c6d8c5d11a8b42e5538cfb86432780
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
If B1FC (Battery Full Capacity) is higher than B1DC (Battery Design
Capacity), only report the design capacity. This handles cases where
the battery calibration is incorrect, and the battery runs out before
the OS thinks it's empty.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ib3e4769c809b69e0a237b5f043e6c41c12d53752
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Since we want to read the non-x86 CBMEMC from SMM we need to be stricter
on where we read from. This change forces the verstage binary and x86
code to agree on the CBMEMC transfer buffer location and size.
BUG=b:221231786
TEST=Boot guybrush and verify verstage transfer buffer still ends up in
cbmem
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ida7d50bef46f280be0db1e1f185b46abb0ae5c8f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
I want to reuse the transfer buffer methods in SMM, so I need to add
them into their own file. I renamed `setup_cbmem_console` to
`replay_transfer_buffer_cbmemc` so it has a more descriptive name. I
also fixed the comment on `verify_psp_transfer_buf`.
BUG=b:221231786
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4f3a8b414b91f601c3a9c3dc7af8f388286fe4da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
We need to save the transfer buffer so we can transfer the cbmem
console and timestamps into x86 DRAM.
BUG=b:221231786
TEST=Boot guybrush and verify S0i3 resume works. Also dumped the
transfer buffer from the OS and verified the console contents got
transferred.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1d3b34c90e0e18609b0c6a0cdedab35aeefbd84b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
All SoCs/chipsets that select ARCH_X86 will end up using the
implementation in cpu/x86/lapic/lapic.c, so to avoid confusion, drop the
unused weak implementation that returns a different value.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iffcd8c80260f9a7d81dda41a0ad08bffc7620c33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Both the secondary and subordinate bus numbers are configured in this
function but it's not easy to search for in the tree as the PCI writes
are hidden inside a bigger write to 'PCI_PRIMARY_BUS'. Use separate
variables and PCI config writes to improve the readability.
Change-Id: I3bafd6a2e1d3a0b8d1d43997868a787ce3940ca9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The XTAL 26MHz test failed on krabby, so we adjust RTC capid from
default value 0x88 to 0xC0 for MT8186. We also add a new log message
to show the capid value which is read from MT6366.
This implementation is according to chapter 5.13 in MT8186 Functional
Specification.
BUG=b:218439447
TEST=set capid to 0xc0.
TEST=XTAL 26MHz test passed.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I16ab46a5697d304e8001de231ffc9b7b7a2f9282
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
google/brask is using SODIMMs for DRAM. Reading spd data is
surprisingly slow (~170 ms), therefore enable the SPD cache.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=run on the device and measure the boot time decrease.
Change-Id: If0a0072160a48b607ad17c0a1819ab49eaad92db
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
In order to cache the spd data which reads from the memory module, we
add SPD_CACHE_ENABLE option to enable the cache for the spd data. If
this option is enabled, the RW_SPD_CACHE region needs to be added to
the flash layout for caching the data.
Since the user may remove the memory module after the bios caching the
data, we need to add the invalidate flag to invalidate the mrc cache.
Otherwise, the bios will use the mrc cache and can make the device
malfunction.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=build pass and enable this feature to the brask
the device could speed up around 150ms with this feature.
Change-Id: If7625a00c865dc268e2a22efd71b34b40c40877b
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62294
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's easier to read and to add new packages when each package is on its
own line and they're sorted alphabetically.
Indenting them also makes it easier to see what's getting installed and
what's a command.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ibfe297bd408ed0783fcff09c1ecb5672fe785c48
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62446
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The linkchecker tool is now being used to find broken links in our
websites. Since it's not needed for building anything, just add it to
the jenkins-node Dockerfile instead.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Iac2246b5378e556b5cd9f2107fc5a7e51d583b5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62445
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch removes Rcomp settings. In MRC design, it checks if the
Rcomp settings from the board is 0 or null, if so, it uses the
recommended Rcomp values. Otherwise, it uses the Rcomp settings passed
from the UPD. From the change history of MRC, we're chasing a moving
target. This RCOMP setting in coreboot is an old setting while the
Rcomp settins in MRC are optimized settings. Moving forward, if there
is a new stepping, it might be changed again which increases the
maintenance effort in coreboot. IMHO, we should let MRC to set the
optimized RCOMP values for the design.
BUG=b:219378758
TEST=emerge-byra coreboot chromeos-bootimage and boots up with QS and
PRQ CPUs. Checks with MRC log and ensure the RCOMP settings are
filled properly by MRC.
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Change-Id: I8547e187b74f9b2cee57ddad2883d60c05d0b9fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
With GPP_B3 locked, primus eMMC SKU encounter eMMC storage lost after
warm reboot.
Config GPP_B3 unlocked to make reboot works on primus. Also set
GPP_B3 to low in early_gpio_table to meet eMMC-PCIe bridge IC power
on sequence.
BUG=b:221488504
TEST=USE="project_primus" emerge-brya coreboo chromeos-bootimage
test reboot 30 cycles passed on primus.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ifd5f9d59d33cd1c5ebe0454ab3aa4c5641c16ff6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Chausie doesn't have recovery mode buttons so it's impossible to
manually enter recovery mode to enable developer mode. This means we
need to force developer mode.
BUG=none
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id0b08ee8e009e8603f63e691b5a7a2ac04e1fc3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
In order to abstract bus-specific logic from TPM logic, the prototype
for two vendor-specific tis functions are added in this
patch. tis_vendor_read() can be used to read directly from TPM
registers, and tis_vendor_write() can be used to write directly to TPM
registers.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I939cf5b6620b6f5f6d454c53fcaf37c153702acc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Instead of using raw integers to indicate success/failure, enum cb_err
can be used to makes things clearer, so this patch converts most
functions to return that instead of int.
TEST=boot to OS on google/dratini, no TPM errors seen
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ifb749c931fe008b16d42fcf157af820ec8fbf5ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Enable STT and decrease sustained_power_limit_mW to 12W
BUG=b:219616787
BRANCH=guybrush
TEST=emerge-guybrush coreboot
update the thermal setting value by measurement and
pass the thermal performance test
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: I5b7b0156fb4a1e2be8528a5787ed82acff93f06c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
coreboot should skip sending EOP during S3 resume since CSE doesn't
require EOP in resume path.
Currently EOP is being sent during PAYLOAD_BOOT or PAYLOAD_LOAD stage
which doesn't get called during S3 resume.
In case EOP is moved in earlier stage, coreboot might send EOP in S3
resume as well. This patch adds check before calling cse_send_eop.
BUG=b:211085685
BRANCH=None
TEST=Check by moving EOP to earlier stage. EOP sending is skipped during
S3 resume.
Change-Id: I8f22446974bc1e7b2d57468633c36bb99ffe1436
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
We don't currently have a build target defined for .map files. This
means they can't be used as a dependency. This change splits the .map
creation into its own rule.
BUG=b:221231786
TEST=Build guybrush and verify .map still exists
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1ce21902e97390aa9520670299ef08debf4458db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Martin Roth <martinroth@google.com>
We currently delete intermediate files. This can make it difficult to
debug and is also unexpected. Setting .SECONDARY will prevent make from
deleting the files.
BUG=b:221231786
TEST=Build guybrush with CL stack and see .map files are preserved
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I657a696acc71d42ba94442d4754ee63efd3e6a74
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Martin Roth <martinroth@google.com>
Currently the LPIT Get Constraints _DSM subfunction returns a package
containing the path to a nonexistent device (\NULL). This is used to
work around an issue with Windows, where returning an empty package will
cause a BSOD. However, using this non-existent device can also cause
confusion, as on Linux, it shows an error in dmesg, e.g.
ACPI Error: AE_NOT_FOUND, While resolving a named reference package
element - \NULL (20200925/dspkginit-438)
Therefore, this patch modifies this returned package slightly to include
the path to ACPI_CPU_STRING for CPU 0, which should always be emitted on
Intel platforms that use the PEP driver.
Tested on google/brya0 on ChromeOS 5.10 kernel
Tested with current Windows 11 ISO
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: If74a1620ff0de33bcdba06e1225c5e28c64253e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Shobhit Srivastava <shobhit.srivastava@intel.corp-partner.google.com>
The USB port configuration was derived from the PPR and schematics.
This board has 6(some multi-purpose) ports.
Primary functions are:
2 USB-C ports
1 USB SS+ type A port
2 Cameras
1 Bluetooth transceiver
BUG=b:214413631
TEST=builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Ie1b05f190f25dca1566e1023011cc70c2d32f461
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
PCI bus 0 is not below any PCI device. In case of pci_domain_scan_bus(),
it's our virtual `domain` device.
Expecting a PCI device above bus 0 resulted in undefined behavior for
all boards with PCI. Only boards with a PCI device 00:00.0 that looked
like a PCIe bridge showed issues, though (e.g. OCP/DeltaLake).
Change-Id: I1fd68b9dc0d2e388ec2bbba4adbadd33e14f0171
Signed-off-by: Nico Huber <nico.h@gmx.de>
Fixes: commit 777ffff442 (device/pci_device.c: Scan only one device for PCIe)
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62376
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The list of releases will grow and in the current state each release
moves the section for the upcoming release more down making it less
visible.
Thus, switch both sections, so that the documentation for the
upcoming release is at the top. Also, invert the order of the previous
releases, so that the latest is at the top.
Change-Id: I69987e035f38ae3ca14dbf5c7644d5292106a978
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62411
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The release notes document also contains information about upcoming
releases, not only previous releases. Thus, rename the document in the
main menu and give it a proper title.
Change-Id: I4480c0b6e4be6fcbcb9a00beb0be169a7eed435d
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The variable `RM` is empty and thus set it to `rm`. While
executing the `clean` rule, run each `rm` command with the -f flag
to ignore non-existing files.
Also, disable the objutil feature locally fixing another build issue.
Change-Id: Icb17e2c924ef480f8ac6195f96cf495709a0a023
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62415
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
@@ -14,7 +14,7 @@ their development kit with them and conduct development sessions.
[Open Source Firmware at Facebook](https://fosdem.org/2019/schedule/event/open_source_firmware_at_facebook/) by [David Hendricks](https://github.com/dhendrix) and [Andrea Barberio](https://github.com/insomniacslk) at [FOSDEM 2019](https://fosdem.org/2019/) ([video](https://video.fosdem.org/2019/K.4.401/open_source_firmware_at_facebook.mp4)) ([slides](https://insomniac.slackware.it/static/2019_fosdem_linuxboot_at_facebook.pdf)) (2019-02-03)
[Open Source Firmware - A love story](https://www.youtube.com/watch?v=xfqKm190dbU) by [Philipp Deppenwiese](https://cybersecurity.9elements.com) at [35c3](https://events.ccc.de/congress/2018)
[Open Source Firmware - A love story](https://www.youtube.com/watch?v=xfqKm190dbU) by [Philipp Deppenwiese](https://cybersecurity.9elements.com) at [35c3](https://web.archive.org/web/20211027210118/https://events.ccc.de/congress/2018/wiki/index.php/Main_Page)
* The charger must be connected (either USB-C or DC Jack)
* BIOS Lock must be disabled
* Supported Linux distribution (Ubuntu 20.04 +, Linux Mint 20.1 + elementaryOS 6 +, Manjaro 21+)
**fwupd 1.5.6 or later**
To check the version of **fwupd** you have installed, open a terminal window and enter the below command:
```
fwupdmgr --version
```
This will show the version number. **1.5.6** or greater will work.
On Ubuntu 20.04, Ubuntu 20.10, Linux Mint 20.1 and elementaryOS 6, fwupd 1.5.6 can be installed from our PPA with the below terminal commands:
```
sudo add-apt-repository ppa:starlabs/ppa
sudo apt update
sudo apt install fwupd
```
On Manjaro:
```
sudo pacman -Sy fwupd-git flashrom-starlabs
```
Instructions for other distributions will be added once fwupd 1.5.6 is available. If you are not using one of the distributions listed above, it is possible to install coreboot using a Live USB.
**Disable BIOS Lock**
BIOS Lock must be disabled when switching from the standard AMI (American Megatrends Inc.) firmware to coreboot. To disable BIOS Lock:
1\. Start with your LabTop turned off\. Turn it on whilst holding the **F2** key to access the BIOS settings.
2\. When the BIOS settings load, use the arrow keys to navigate to the **Advanced** tab\. Here you will see **BIOS Lock**\.
3\. Press `Enter` to change this setting from **Enabled** to **Disabled**
4\. Next, press the `F10` key to **Save & Exit** and then `Enter` to confirm.
#### **Switching Branch**
Switching branch refers to changing from AMI firmware to coreboot, or vice versa.
First, check for new firmware files with the below terminal command:
```
fwupdmgr refresh --force
```
Then, to change branch, enter the below terminal command:
```
fwupdmgr switch-branch
```
You can then select which branch you would like to use, by typing in the corresponding number:
You will be prompted to confirm, press `y` to continue or `n` to cancel.
Once the switch has been completed, you will be prompted to restart.
The next reboot can take up to **5 minutes,** do not interrupt this process or disconnect the charger. Once the reboot is complete, that's it - you'll continue to receive updates for whichever branch you are using.
- CPU (full processor specs available at https://ark.intel.com)
- Intel i7-10710U (Comet Lake)
- Intel i3-10110U (Comet Lake)
- EC
- ITE IT8987E
- Backlit Keyboard, with standard PS/2 keycodes and SCI hotkeys
- Battery
- Charger, using AC adapter or USB-C PD
- Suspend / resume
- GPU
- Intel UHD Graphics 620
- GOP driver is recommended, VBT is provided
- eDP 13-inch 1920x1080 LCD
- HDMI video
- USB-C DisplayPort video
- Memory
- 16GB on-board *1
- Networking
- AX201 CNVi WiFi / Bluetooth soldered to PCBA
- Sound
- Realtek ALC256
- Internal speakers
- Internal microphone
- Combined headphone / microphone 3.5-mm jack
- HDMI audio
- USB-C DisplayPort audio
- Storage
- M.2 PCIe SSD
- RTS5129 MicroSD card reader
- USB
- 1280x720 CCD camera
- USB 3.1 Gen 2 Type-C (left)
- USB 3.1 Gen 2 Type-A (left)
- USB 3.1 Gen 1 Type-A (right)
[^1] The Comet Lake PCB supports multiple memory variations that are based on hardware configuration resistors see `src/mainboard/starlabs/labtop/variants/cml/romstage.c`
## Building coreboot
### Preliminaries
Prior to building coreboot the following files are required:
* Intel Flash Descriptor file (descriptor.bin)
* Intel Management Engine firmware (me.bin)
* ITE Embedded Controller firmware (ec.bin)
The files listed below are optional:
- Splash screen image in Windows 3.1 BMP format (Logo.bmp)
These files exist in the correct location in the StarLabsLtd/blobs repo on GitHub which is used in place of the standard 3rdparty/blobs repo.
### Build
The following commands will build a working image:
```bash
make distclean
make defconfig KBUILD_DEFCONFIG=configs/config.starlabs_labtop_cml
make
```
## Flashing coreboot
```eval_rst
+---------------------+------------+
| Type | Value |
+=====================+============+
| Socketed flash | no |
+---------------------+------------+
| Vendor | Winbond |
+---------------------+------------+
| Model | 25Q128JVSQ |
+---------------------+------------+
| Size | 16 MiB |
+---------------------+------------+
| Package | SOIC-8 |
+---------------------+------------+
| Internal flashing | yes |
+---------------------+------------+
| External flashing | yes |
+---------------------+------------+
Please see [here](../common/flashing.md) for instructions on how to flash with fwupd.
* The charger must be connected (either USB-C or DC Jack)
* BIOS Lock must be disabled
* Supported Linux distribution (Ubuntu 20.04 +, Linux Mint 20.1 + elementaryOS 6 +, Manjaro 21+)
**fwupd 1.5.6 or later**
To check the version of **fwupd** you have installed, open a terminal window and enter the below command:
```
fwupdmgr --version
```
This will show the version number. **1.5.6** or greater will work.
On Ubuntu 20.04, Ubuntu 20.10, Linux Mint 20.1 and elementaryOS 6, fwupd 1.5.6 can be installed from our PPA with the below terminal commands:
```
sudo add-apt-repository ppa:starlabs/ppa
sudo apt update
sudo apt install fwupd
```
On Manjaro:
```
sudo pacman -Sy fwupd-git flashrom-starlabs
```
Instructions for other distributions will be added once fwupd 1.5.6 is available. If you are not using one of the distributions listed above, it is possible to install coreboot using a Live USB.
**Disable BIOS Lock**
BIOS Lock must be disabled when switching from the standard AMI (American Megatrends Inc.) firmware to coreboot. To disable BIOS Lock:
1\. Start with your LabTop turned off\. Turn it on whilst holding the **F2** key to access the BIOS settings.
2\. When the BIOS settings load, use the arrow keys to navigate to the **Advanced** tab\. Here you will see **BIOS Lock**\.
3\. Press `Enter` to change this setting from **Enabled** to **Disabled**
4\. Next, press the `F10` key to **Save & Exit** and then `Enter` to confirm.
#### **Switching Branch**
Switching branch refers to changing from AMI firmware to coreboot, or vice versa.
First, check for new firmware files with the below terminal command:
```
fwupdmgr refresh --force
```
Then, to change branch, enter the below terminal command:
```
fwupdmgr switch-branch
```
You can then select which branch you would like to use, by typing in the corresponding number:
You will be prompted to confirm, press `y` to continue or `n` to cancel.
Once the switch has been completed, you will be prompted to restart.
The next reboot can take up to **5 minutes,** do not interrupt this process or disconnect the charger. Once the reboot is complete, that's it - you'll continue to receive updates for whichever branch you are using.
You can switch branch at any time.
Please see [here](../common/flashing.md) for instructions on how to flash with fwupd.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
