We only write to the IOSAV LFSR registers twice, but we do so between
the writes to the other four IOSAV per-subsequence registers. Since we
know that the IOSAV is sleeping when we program the subsequences, we
might as well do the two oddball LFSR register writes after we have
programmed the always-written-to group of four registers. That way,
subsequent changes can reproducibly replace the four writes with a
single macro.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: If7bb14a9862a53a3eba565d17401347dcc9ffbe9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40973
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch implements the pin changes needed for Trogdor rev1.
Unfortunately, coreboot has to get the EC and TPM SPI busses compiled
into Kconfig, so we cannot really build a single image that runs on both
revisions. Introduce a Kconfig to handle this instead.
Change-Id: I2e48dc4565682c12089b6cf92c29f4cef4d61bb8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support to configure the Silver and L3 PLLs and switch the APSS
GFMUX to use the PLL to speed up the boot cores.
Tested: CPU speed frequency validated for speed bump
Change-Id: Iafd3b618fb72e0e8cc8dd297e4a3e16b83550883
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Transfer sequence used by SPI-Flash application present in CB/DC.
1. Assert CS through GPIO
2. Data transfer through QSPI (involves construction of command
descriptor for multiple read/write transfers)
3. De-assert CS through GPIO.
With above sequence, in DMA mode we dont have the support for read
transfers that are not preceded by write transfer in QSPI controller.
Ex: "write read read read" sequence results in hang during DMA transfer,
where as "write read write read" sequence has no issue.
As we have application controlling CS through GPIO, we are making
fragment bit "set" for all transfers, which keeps CS in asserted
state although the ideal way to operate CS is through QSPI controller.
Change-Id: Ia45ab793ad05861b88e99a320b1ee9f10707def7
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39807
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change moves all the logic for setting up decode windows for LPC
under configure_child_lpc_windows() which is called from
lpc_enable_children_resources(). This is in preparation to configure
decode windows for eSPI differently if mainboard decides to use eSPI
instead of LPC.
Side-effect of this change is that the IO decode registers are written
after each child device resources are considered.
BUG=b:154445472
Change-Id: Ib8275bc4ce51cd8afd390901ac723ce71c7a9148
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41070
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
eSPI on Picasso is configured using the LPC bridge configuration
registers. This change enables config options to allow SoC to select
if it supports eSPI (SOC_AMD_COMMON_BLOCK_HAS_ESPI) and mainboard to
select if it wants to use eSPI instead of LPC for talking to legacy
devices and embedded controllers (SOC_AMD_COMMON_BLOCK_USE_ESPI).
BUG=b:154445472
Change-Id: I15e9eb25706e09393c019eea4d61b66f17490be6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41069
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Historical Permission Notice and Disclaimer (with and without
permission to sell) is a BSD-style license family that OSI and SPDX
consider deprecated - and yet, it's right here in our tree.
Change-Id: I61624b6e54e9aba6e2f54822c1f68967c416ad3d
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41221
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add an SSDT generator for Maxim 98390 kernel driver.
Copied from 'drivers/i2c/rt1011'.
BUG=b:149443429
BRANCH=None
TEST=built coreboot and checked audio function with kernel patch on nightfury
Change-Id: I64d776c6c9726eb5822ad4dd82f6826c2a30cb1d
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39463
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In a few cases a license was added: Stuff coming from Linux is
"GPL-2.0" (not GPL-2.0-only!), build-release is by me and got the
usual GPL-2.0-only treatment. uio_usbdebug and spkmodem had their
licenses propagate to all their files.
Change-Id: Ia5712bbaa417cb9e937834512351fcc0acfa16be
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41202
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As requested by Stefan.
For nvramtool some of these lines are part of a paragraph of fluff,
so manual processing was easier than adapting the script used for
the rest of the tree.
Change-Id: Id52c4c264cded0582a97da131b695a046cbd67c6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Martin Roth <martinroth@google.com>
This is all code coming from the outside, so let's keep these files
untouched as much as possible.
A couple of files is added to the list by name because their license,
while free, can't be properly modelled in SPDX:
- lzmadecode is (LGPL OR CPL) WITH special-exception
- stack.c and start16 are some weird (but free) US Gov't license grant
- two XGI related files have "BSD except for Linux, where it's GPL"
Change-Id: I42dec503b9c427a66792d3fec99ca8df1a360e47
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Fold this last ASUS 440BX board into the P2B family, while bringing in
some changes:
- Devicetree becomes overridetree.
- Remove non-existent IR device and disable ACPI device on Super I/O to
match OEM firmware.
- Add SB GPO settings from OEM firmware to devicetree. This disables
the SPD enabling magic this board needs. By moving the enabling part
to bootblock the hacky enable_spd hook can be eliminated.
- Initialize the serial port in bootblock, like the other boards.
Boot tested on hardware.
Change-Id: I65f2cb9d1bd4c82550de43889e3502526a46bd18
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41047
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 73b723d [google/cyan: Switch Touchpad and Touchscreen...]
in additon to changing the touchpad/touchscreen interrupts from
edge to level triggered, also marked them as maskable.
This was partially reverted in a86bbea0 [google/cyan: set
touchscreen GPIO to non_maskable], but did not resolve all of the
issues. Additionally, 73b723d also accidentally changed the pad
interrupt select from L3 to L1 for all touchscreen GPIOs.
Clean up this mess by setting all touchpad/touchscreen GPIOs
back to maskable, and set the pad level to L3 for all touchscreen
GPIOs.
Tested on several cyan variants
Change-Id: I70e8e2d4ff317c3b9b4108ed6c5bc80e9b0bbc75
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add setting of the MaxPayload for each root port from the device tree.
By default MaxPayload is set to 128 bytes. This change allows changing
to 256 bytes.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: I61e1d619588a7084d52bbe101acd757cc7293cac
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Really old versions of W83977TF Super I/O had an IR logical device, but
is no longer the case. It does not exist in the newer W83977EF version,
installed in some Asus P2B family boards, and served by this same code.
Add a config option on the off chance we may see board with it (as if
we would) and don't include this device unless it is set. Saves us from
the need to declare a not-present device off and/or extraneous PNP
device errors about a not-present device.
Change-Id: I761ebc41f1735a03e768339a68ca139167edc095
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41004
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
LTE module Fibocom L850-GL is lost after idle overnight, with this workaround, host will not initiate U3 wakeup at the same time with device, which will avoid the race condition.
Disable XHCI LFPS power management. If the option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0.
BUG=b:155955302
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] are set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I88357f44317a5cff2e04508638eb065e5ada4c4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
C-State latency table was exposed by both intel-idle driver and
BIOS/coreboot. And table in Kernel was used before.
After kernel patch (https://patchwork.kernel.org/patch/11290319/),
only BIOS/coreboot exposes C-State latency table through _CST.
As current C-State latency table info is not correct for Tigerlake,
update proper info according to BWG and reference code.
- Update latency: CpuPowerMgmt.h
Use BIOS reference code as values in BWG is not up-to-dated
- Remove MSR program for latency: BWG 4.6.4.3.4
Reference:
- TGL BWG #611569 Rev 0.7.6
- https://github.com/otcshare/CCG-TGL-Generic-SiC/blob/master/
ClientOneSiliconPkg/Cpu/Include/CpuPowerMgmt.h
BUG=b:155223704
BRANCH=None
TEST=Boot to OS and check C-State latency
expected result
>cat /sys/devices/system/cpu/cpu0/cpuidle/state*/{name,latency}
POLL
C1_ACPI
C2_ACPI
C3_ACPI
0
1
253
1048
For detail, refer Bug info.
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I8bf2976ad35b4cf6f637a99c26b4f98f9f6ee563
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
SMI handler was not present in jasperlake rvp to handle wake events
when platform goes to sleep or shutdown or s0ix.
Adding this support for board which supports chromeec.
BUG=None
BRANCH=None
TEST=Check wake event on board and platform wakes up due to events
lid wake event or power button press.
Change-Id: I8e35955b06d6efaf9275ec03f519c9bcaa9ba345
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
anx7625 enables MIPI receiver to check EOTP packet as default.
If MIPI_DSI_MODE_EOT_PACKET is not set in flags, soc dsi will not
send out EOTP packet and some panel models will display abnormal
such as scrolling all the time.
BUG=b:144824303
BRANCH=kukui
TEST=boot damu board, edp panel with anx7625 as bridge boots up
without scrolling.
Signed-off-by: Paul Ma <magf@bitland.corp-partner.google.com>
Change-Id: Iad651202bde2a40024af8c12153143ada2ce2439
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41161
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:41106 revealed that mb/intel/cedarisland already sets FSP-S UPD (see
CB:40735) while the required includes are still missing in CPX. Buildbot
did not fail because `ramstage.c` never was (implicitly) included.
Fix this problem by making SKX/CPX share a common ramstage header for
now by moving the one from SKX.
Test: Build cedarisland_crb
Change-Id: I9cd25edd167ec71ee98c7ffa4fa6f95ca73a75e9
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
This enables adding ACPI objects at run-time for SD Card and EMMC
devices.
BUG=b:150872580
TEST=Build and boot the mainboard. Observe ACPI objects like card detect
gpio are added to the SSDT.
Change-Id: I754aee3b0fd343994bd06d9c28e038f651009d6d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
On Apollo Lake/Gemini Lake platforms, FSP requires more than a
simple RW_MRC_CACHE; without the RECOVERY and VAR cache regions,
FSP-m will fail on s3 resume and trigger a full reset instead.
This fixes the default.fmd for octopus to match that used for reef.
Test: build/boot google/ampton, verify sleep/resume works under Linux
with 5.x kernel.
Change-Id: I8565aa93256df7d6e0b359d70e9305f34e5ccb60
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Send end of post message to CSME in FSP, by selecting EndOfPost
message in PEI phase. In API mode which coreboot currently uses,
sending EndOfPost message in DXE phase is not applicable.
Change-Id: Ie21dcfc84d331f036090d01ea3e3925b81eea902
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
gpio70 is assigned to use as WLAN rst in new schematic to fulfill
RTK RTL8822CE power sequence:
WLAN rst will need to be active at least 50ms after WLAN power on.
Also in order to keep the rst low in consistency, override default
gpio70 to low.
BUG=b:154357210,b:154848243
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I98c8afe42b7f92016f83483acbb3b9ae64b159f7
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40805
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
touchpad & touchscreen power enable gets reset during resume causing
unintended wake interrupts, causing dark resume failures. This
prevents the board from being shut down after it's been suspended
for a long period of time and can end up draining the battery.
BUG=b:153173717
TEST=Build only - Needs to be tested by ODMs.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: If403da8853e59eaaf589062c9bd6f10deb626998
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
vboot_recovery_mode_enabled() was recently changed to assert() when it
is called before vboot logic has run, because we cannot determine
whether we're going to be in recovery mode at that point and we wanted
to flush out existing uses that pretended that we could. Turns out there
are a bunch of uses like that, and there is some code that is shared
across configurations that can and those that can't.
This patch cleans them up to either remove checks that cannot return
true, or add explicit Kconfig guards to clarify that the code is shared.
This means that using a separate recovery MRC cache is no longer
supported on boards that use VBOOT_STARTS_IN_ROMSTAGE (this has already
been broken with CB:38780, but with this patch those boards will boot
again using their normal MRC caches rather than just die). Skipping the
MRC cache and always regenerating from scratch in recovery mode is
likewise no longer supported for VBOOT_STARTS_IN_ROMSTAGE.
For FSP1.1 boards, none of them support VBOOT_STARTS_IN_BOOTBLOCK and
that is unlikely to change in the future so we will just hardcode that
fact in Kconfig (otherwise, fsp1.1 raminit would also have to be fixed
to work around this issue).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I31bfc7663724fdacab9955224dcaf650d1ec1c3c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch improves the response buffer handling for TPM 2.0. Previously
we would allow any command to return no payload, but if there was a
payload we would always try to unmarshal it according to the normal
success response. This was sort of relying on the fact that the TPM
usually returns no additional data after the header for error responses,
but in practice that is not always true. It also means that commands
without a response payload accidentally work by default even though we
did not explicitly add unmarshallig support for them, which seems
undesirable. Adding explicit unmarshalling support for TPM2_SelfTest
which was only supported through this loophole before.
This patch changes the behavior to always accept any amount of payload
data for error responses but not unmarshal any of it. None of our use
cases actually care about payload data for errors, so it seems safer to
not even try to interpret it. For success responses, on the other hand,
we always require support for the command to be explicitly added.
This fixes a problem with the Cr50 GET_BOOT_MODE command where an error
response would only return the subcommand code but no data after that.
Also add support for a second, slightly different NO_SUCH_COMMAND error
code that was added in Cr50 recently.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib85032d85482d5484180be6fd105f2467f393cd2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41100
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Andrey Pronin <apronin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates memranges_find_entry() to break and return early
if the end address of the hole within the current range entry crosses
the requested limit. This is because all range entries and maintained
in increasing order and so none of the following range entries can
satisfy the given request.
Change-Id: I14e03946ddbbb5d254b23e9a9917da42960313a6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We use a temporary BAR value to program the thermal settings. To make
this more obvious, factor it out.
Tested with BUILD_TIMELESS=1, Asus P8Z77-V LX2 does not change.
Change-Id: Icda6e4100d954fe28d2624270b5d7ab7ed155e32
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Similar to bootblock, provide declaration for
verstage_mainboard_early_init() to support early mainboard
initialization if verstage is run before bootblock.
BUG=b:155824234
TEST=Verified that trembyle still builds
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I106213ecc1c44100f1f74071189518563ac08121
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The hardware IRQ option was not passed to SeaBIOS Makefile and resulted
in HARDWARE_IRQ being permanently disabled regardless of Kconfig
selection in coreboot. On platforms that need the hardware IRQ it caused
hangs at boot menu or iPXE prompts.
TEST=enter SeaBIOS boot menu on Libretrend LT1000
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iafcfd743177bbcd1ee23e227c74dd8268c4c23c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
chip_instance structure currently uses a ref_count to determine how
many devices hold reference to that instance. If the count drops to
zero, then it is assumed that the chip instance is a duplicate in
override tree and has a similar instance that is already overriden in
base device tree.
ref_count is currently decremented whenever a device in override tree
matches the one in base device tree and the registers from the
override tree instance are copied over to the base tree instance. On
the other hand, if a device in override tree does not match any device
in base tree under a given parent, then the device is added to base
tree and all the devices in its subtree that hold pointers to its
parent chip instance are updated to point to the parent's chip
instance in base tree. This is done as part of update_chip_pointers.
However, there are a couple of issues that this suffers from:
a) If a device is present only in override tree and it does not have
its own chip (i.e. pointing to parent's chip instance), then it
results in sconfig emiiting parent's chip instance (which can be the
SoC chip instance) in static.c even though it is unused. This is
because update_chip_pointers() does not call delete_chip_instance()
before reassigning the chip instance pointer.
b) If a device is added under root device only in the override tree
and it does not have its own chip instance (i.e. uses SoC chip
instance), then it results in sconfig emitting a copy of the SoC chip
instance and setting that as chip_ops for this new device in the
override tree.
In order to fix the above issues, this change drops the ref_count
field from chip_instance structure and instead adds a forwarding
pointer `base_chip_instance`. This is setup as per the following
rules:
1. If the instance belongs to base devicetree, base_chip_instance is
set to NULL.
2. If the instance belongs to override tree, then it is set to its
corresponding chip instance in base tree (if present), else set to
NULL.
State of base_chip_instance is then used when emitting chips and
devices using the following rules:
1. If a chip_instance has non-NULL base_chip_instance, then that chip
instance is not emitted to static.c
2. When emitting chip_ops for a device, base_chip_instance is used to
determine the correct chip instance name to emit.
BUG=b:155549176
TEST=Verified that the static.c file generated for base/override tree
combination is correct when new devices without chips are added only
to override tree.
Change-Id: Idbb5b34f49bf874da3f30ebb6a6a0e2d8d091fe5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41007
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change moves the assignment of id for chip instance from
new_chip_instance() to emit_chips(). This is similar to the previous
change for moving dev id assignment to happen much later.
This ensures that the same ID gets assigned to a chip when adding
support for device trees which makes it easier to compare static.c
files.
BUG=b:155549176
Change-Id: I3efa9af5ed91123675be42bce1cb389bad19cb62
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change drops the id field from struct device as used by
sconfig. It was primarily used for generating unique device names. This
was maintained within device structure so that the order in which the
device tree entries were parsed is clear. Since the ids are assigned
in parsing order, it is problematic when a device is moved from base
devicetree to override tree. The entire parsing order changes which
makes it really difficult to compare what really changed in static.c
file.
By moving the dev name assignment to happen later when doing pass0 of
static.c generation, the difference in static.c file is minimized when
adding support for override trees.
BUG=b:155549176
Change-Id: I31870ace5a2fd7d5f95ab5e30d794c3bc959ed46
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41005
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This replaces GPLv2-or-later and GPLv2-only long form text with the
short SPDX identifiers.
Commands used:
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.*of.*the.*License.*or.*(at.*your.*option).*any.*later.*version.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-or-later */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation[.;,].+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This software is licensed under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation,.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
Change-Id: I7a746088a35633c11fc7ebe86006e96458a1abf8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This driver was previously added for another out-of-tree Librem device, but
forgot to switch over the librem_skl boards to use it. Remove
duplicate functionality from mainboard.c and delete the empty file.
Test: build/boot Librem 13v2 and verify serial number read from CBFS
via dmidecode.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: Ide952197335c6bfbad846c6d6f62be5c4c57e2cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Every device belongs to a chip. And we already keep that relation by
inheriting the `.chip_info` pointer if downstream devices don't have
another chip specified. So we can also allow to specify `register`
settings at the device level.
Change-Id: I44e6b95d0cd708fef69b152ebc46b869b2bb9205
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40803
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch configures all IP related GPIOs as per mainboard schematics.
Till now, we were relying on FSP to do IP specific GPIO programming but
now we'll program all GPIOs from mainboard.
This will remove ambiguity of GPIO programming done by FSP and coreboot
will do full GPIO programming
Programming GPIOs of following IPs
- I2C
- Emmc
- Display
- CPU specific gpio (SLP lines)
- Cnvi
- SD
BUG=None
BRANCH=None
TEST=compile coreboot and checked that all IP functionality working.
Change-Id: I98583b768cbd8ab4af536b31d758cb1cee93edfb
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
SdCardPowerEnableActiveHigh is a UPD which controls polarity of SD card
power enable pin. Setting it 1 will set polarity of this pin as Active
high. This patch will allow to control it from devicetree so that it
can be set as per each board's requirement.
BUG=b:155595624
BRANCH=None
TEST=Build, boot JSLRVP, Verified UPD value from FSP log
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Change-Id: Id777a262651689952a217875e6606f67855fc2f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41027
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PMC supports messages that can be used for configuring the USB
Type-C Multiplexer/Demultiplexer.
BUG=b:151646486
TEST=Booted to kernel on volteer board and verified PMC and Mux
agent devices identification.
Change-Id: I00c5f929b2eea5de3f8eba794dbe9b36c8083c52
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update interrupt setting based on latest FSP(3163.01)
Reference:
https://github.com/otcshare/CCG-TGL-Generic-SiC/blob/TGL.3163.01/
ClientOneSiliconPkg/IpBlock/Itss/LibraryPrivate/PeiItssPolicyLib/
PeiItssPolicyLibVer2.c
BUG=b:155315876
BRANCH=none
TEST=Build with new FSP(3163.01) and boot OS and login OS console
in ripto/volteer. Without this change, we can't login due to mismatch
interrupt setting between asl and fsp setting.
Cq-Depend: chrome-internal:2944102
Cq-Depend: chrome-internal:2939733
Cq-Depend: chrome-internal:2943140
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ibf70974b8c4f63184d576be3edd290960b023b1e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40872
Reviewed-by: Dossym Nurmukhanov <dossym@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Due to refactoring of Serial IO code in FSP v3163 onwards we need to
set SerialIoUartDebugMode UPD in FSP-M to SkipInit so that SerialIoUart
initialization is skipped in FSP. This makes sure that SerialIo
initialization in coreboot is not changed by FSP.
BUG=b:155315876
BRANCH=none
TEST=build and boot tglrvp/ripto/volteer and check UART debug logs
Cq-Depend: chrome-internal:2944102
Cq-Depend: chrome-internal:2939733
Cq-Depend: chrome-internal:2943140
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I8ba4b9015fa25a84b6b99419ce4d413c9d9daa44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40899
Reviewed-by: Dossym Nurmukhanov <dossym@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The latest Intel FSP advertises xHCI v1.2 chipset support, so update
libpayload to include that version. No critical changes were identified
in review of the xHCI v1.2 spec, and booting from USB works with the
included change as expected.
BUG=b:155315876
TEST=booting from multiple USB sticks/hubs with the latest Intel FSP
that advertises xHCI v1.2
Change-Id: I236fed9beef86ff5e1bf7962d882fdae5817a1ff
Signed-off-by: Dossym Nurmukhanov <dossym@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41039
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Librem SKL/KBL boards do not have an exposed serial port interface.
Set board Kconfig so that a default built image with Tianocore payload
is bootable and doesn't hang due to trying to send data over a
non-existant serial port.
Test: build/boot librem 13v4 with board defaults + Tianocore
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: I4c3f8a3c1726f804957b06b437b399291854a3f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Per the schematics, SRCCLKREQ2# is used for the NVMe and should be
enabled. Enable CLKREQ for PCIe RP9, and adjust comments to indicate
correct value used per schematic.
Test: build/boot Librem 15v3 with NVMe drive, verify drive identified
properly and no errors in boot log.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: I159cb7ce1f5195d95c0229490c3bbde26edbd375
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
SataSpeedLimit was set to 3Gbps to work around issues which are now
known to be the result of incorrect FSP behavior. Since SataPwrOptEnable
is now set at the SoC level and ensures the SIR registers are correctly
programmed, we can re-enable 6Gbps operation without errors.
Test: build/boot Librem 13v2 with both m.2 and 2.5" SATA drives,
check dmesg for errors.
Change-Id: I3565dc063724ad288ef92361942fcdc14daac17e
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40909
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For unknown reasons FSP skips a whole bunch of SIR (SATA Initialization
Registers) when SataPwrOptEnable=0, which currently is the default in
coreboot and FSP. Even if FSP's default was 1, coreboot would reset it.
This can lead to all sorts of problems and errors, for example:
- links get lost
- only 1.5 or 3 Gbps instead of 6 Gbps
- "unaligned write" errors in Linux
- ...
At least on two boards (supermicro/x11-lga1151-series/x11ssm-f and
purism/librem13v2) SATA is not working correctly and showing such
symptoms.
To let FSP correctly initialize the SATA controller, enable the option
SataPwrOptEnable statically. There is no valid reason to disable it,
which might break SATA, anyway.
Currently, there are no reported issues on CML and CNL, so a change
there could not be tested reliably. SKL/KBL was tested successfully
without any noticable downsides. Thus, only SKL gets changed for now.
Change-Id: I8531ba9743453a3118b389565517eb769b5e7929
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40877
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since commit 402fe20e (mb/up/squared: Add mainboard) the UP2's eMMC
maximum host speed was reduced to DDR50, because HS200 showed I/O errors
in the host kernel. We found out that with EDK2 master the correct
Host Speed could not be set properly during EDK2 platform init.
Therefore eMMC would not show up for boot device selection.
This commit sets the eMMC MaxHostSpeed to the designed max value of the
used eMMC on the UP2 board and furthermore drops the override from the
ramstage.c. It's already set in the devicetree.cb.
Though CRC errors are still visible in EDK II debug logs, no other
negative effects have been observed.
Signed-off-by: Patrik Tesarik <mail@patrik-tesarik.de>
Change-Id: I8d53204d8a776efd560fbdea918f83e180813179
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In CSE Firmware Custom SKU, CSE region is logically divided into
2 boot partitions. These boot partitions are represented by BP1(RO),
BP2(RW). With CSE Firmware Custom SKU, CSE can boot from either
RO(BP1) or RW(BP2).
The CSE Firmware Custom SKU layout appears as below:
------------- -------------------- ---------------------
|CSE REGION | => | RO | RW | DATA | => | BP1 | BP2 | DATA |
------------- -------------------- ---------------------
In order to support CSE FW update to RW region, below APIs help coreboot
to get info about the boot partitions, and allows coreboot to set CSE
to boot from required boot partition (either RO(BP1) or RW(BP2)).
GET_BOOT_PARTITION_INFO - Provides info on available partitions in the CSE
region. The API provides info on boot partitions like start/end offsets
of a partition within CSE region, and their version and partition status.
SET_BOOT_PARTITION_INFO - Sets CSE's next boot partition to boot from.
With the HECI API, firmware can notify CSE to boot from RO(BP1) or RW(BP2)
on next boot.
As system having CSE Firmware Custom SKU, boots from RO(BP1) after G3,
so coreboot sets CSE to boot from RW(BP2) in normal mode and further,
coreboot ensure CSE to boot from whichever is selected boot partition
if system is in recovery mode.
BUG=b:145809764
TEST=Verified on hatch
Change-Id: Iaa62409c0616d5913d21374a8a6804f82258eb4f
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Make vboot verification code accessible in only verstage.
Vboot verification code in vboot_logic.c is being used
in verstage. Due to support function vboot_save_data(),
so core functionality in vboot_logic.c is made available in romstage.
The patch decouples the support function frm vboot_logic.c to
limit itself to verstage.
BUG=b:155544643
TEST=Verified on hatch
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Id1ede45c4dffe90afcef210eabaa657cf92a9335
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
The index of MEM_STRAPS will be migrated from per DRAM part number to
per DRAM characteristic therefore one index mapped to a single SPD
binary can represent to multiple DRAM part numbers as long as their
characteristic is the same for DRAM controller to support. In this case,
the real DRAM part number would be provisioned in the CBI instead of SPD
in the factory flow. As a result, we need to extract DRAM part number
from CBI.
BUG=b:152019429
BRANCH=None
TEST=1. provision dram_part_num field of CBI
2. check DRAM part number is correct in SMBIOS for memory device
Change-Id: I40780a35e04efb279591e9db179cb86b5e907c0d
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
In order to the Kconfigs in the same directory where the corresponding
code lives, this change moves ACPI_BERT to arch/x86/Kconfig and
following configs to acpi/Kconfig:
ACPI_CPU_STRING
ACPI_HAVE_PCAT_8259
ACPI_NO_PCAT_8259
HAVE_ACPI_TABLES
BUG=b:155428745
Change-Id: I289565f38e46bd106ff89685aaf8f57e53d9827a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40932
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split
into multiple CLs. This is change 5/5 which moves the addition of ACPI
table related files from arch/x86/Makefile.inc to acpi/Makefile.inc.
BUG=b:155428745
Change-Id: I8143fd37357aeb0561516450adddc6714d539ada
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 4/5 which gets rid of the placeholder
header files that were added to temporarily include acpi/ header files
from arch/header files.
BUG=b:155428745
Change-Id: If6e8580c3c6433f9239e06a1dc7ba661b3f597e5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 3/5 which basically is generated by
running the following command:
$ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g'
BUG=b:155428745
Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 2/5 which moves the contents of
arch/x86/include/arch/acpi*.h files into include/acpi/acpi*.h and
updates the arch header files to include acpi header files. These are
just temporary placeholders and will be removed later in the series.
BUG=b:155428745
Change-Id: I9acb787770b7f09fd2cbd99cb8d0a6499b9c64b3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 1/5 which moves .c files from arch/x86 to
acpi/.
The only acpi files that are still retained under arch/x86 are:
a. acpi_s3.c: This doesn't really deal with ACPI tables. Also, there
are some assumptions in there about SMM which will have to be resolved
if this file needs to be moved to common code.
b. acpi_bert_storage.c/bert_storage.h: This file is currently written
specifically with x86 in mind. So, not moving the file for now.
Motivation for this change: Not all stages on Picasso SoC are targeted
for the same architecture. For example, verstage (if runs before
bootblock) will be targeted for non-x86. This makes it difficult to
add device tree to verstage which would be required to get to SoC
configs from the tree. This is because the device tree on x86
platforms currently contains a lot of devices that require ACPI
related enums and structs (like acpi_gpio, acpi_pld, acpi_dp and so
on). Hence, this change removes all ACPI table support out of
arch/x86.
BUG=b:155428745
Change-Id: Icc6b793c52c86483a8c52e0555619e36869a869e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
These boards have the same issue as [27272]:
Currently, two power buttons are exposed in ACPI, and detected by the
operating system.
> As per the ACPI specification, there are two types of power button
> devices:
> 1. Fixed hardware power button
> 2. Generic hardware power button
>
> Fixed hardware power button is added by the OSPM if POWER_BUTTON flag
> is not set in FADT by the BIOS. This device has its programming model
> in PM1x_EVT_BLK. All ACPI compliant OSes are expected to add this
> power button device by default if the power button FADT flag is not
> set.
>
> On the other hand, generic hardware power button can be used by
> platforms if fixed register space cannot be used for the power button
> device. In order to support this, power button device object with HID
> PNP0C0C is expected to be added to ACPI tables. Additionally,
> POWER_BUTTON flag should be set to indicate the presence of control
> method for power button.
>
> [i440BX] mainboards implemented the generic hardware power button in
> a broken manner i.e. power button object with HID PNP0C0C is added to
> ACPI however none of the boards set POWER_BUTTON flag in FADT. This
> results in Linux kernel adding both fixed hardware power button as
> well as generic hardware power button to the list of devices present
> on the system. Though this is mostly harmless, it is logically
> incorrect and can confuse any userspace utilities scanning the ACPI
> devices.
Hardware tests on the P2B-LS shows the generic hardware power button
is not working anyway - with FADT power button flag set, the board
could not power off with the button.
This change removes the generic hardware power button from all P2B
mainboards and relies completely on the fixed hardware power button.
TEST=Booted on P2B-LS, Linux detects only fixed hardware power
button, button still powers off.
[27272]: https://review.coreboot.org/27272
Change-Id: I0f5b7aaf32366360de3cce58cd742651a2bb46ba
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add VBT file, and override use via Kconfig since all Reef variants
use the same VBT file.
VBT extracted from firmware in ChromeOS recovery image.
Test: built/boot google/reef w/FSP display init
Change-Id: I31156ec7371c0443719fdd9ddac6ed4960c83767
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Base on the grunt board schematic, gpio70 is an alternative way for wlan rst.
Add hook for variants to override default state.
BUG=b:154357210,b:154848243
BRANCH=master
TEST=emerge-grunt coreboot
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Change-Id: Ic3f1c016357dd5090e6adedf96e7593abff29a0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Certain boards require SeaBIOS' HARDWARE_IRQ option to be
deselected in order for the platform to boot. Add a Kconfig
to allow selection of HARDWARE_IRQ enablement, and write to
SeaBIOS' .config file in cases where it needs to be disabled.
Deselect the option for google/rambi variants so they boot
with boards defaults.
Test: build/boot google/clapper, verify board boots vs hanging
at boot menu prompt.
Change-Id: I23e9b30d2d1042c86bd10f134d6fe361edaf8cb2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Suggested by Nico Huber in CB:38765.
This placement makes the address calculation simpler and
makes its location indepedent of the number of CPUs.
As part of the change in the BIOS resource list address
calculation, the `size` variable was factored out of the
conditional in line 361, thus eliminating the else.
Change-Id: I9ee2747474df02b0306530048bdec75e95413b5d
Signed-off-by: Eugene D Myers <cedarhouse@comcast.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40437
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a FMAP which supports SMMSTORE and non-ChromeOS payloads,
since Apollo Lake-based devices like Reef cannot use an
automatically-generated FMAP due to strict layout requirements.
Change-Id: If570f92f4f81c0e29777c87756fc5e45af549064
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The table of initial i440BX register values has a bitmask that allows
preserving certain bits as they are programmed. This feature has been
unused since day one and probably will never be used. So drop it.
Drop DRB, RPS, PGPOL registers from the table as they will be
programmed during RAM init. These two reductions combined saved ~104
bytes.
Drop unneeded SDRAMC "+0".
Slightly compact a comment block.
TEST=Boot tested on asus/p2b-ls, i440bx config did not change
Change-Id: I020f616455bb671fe284993a488beb6386a03d0d
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This change adds a helper function cpu_get_lapic_addr() that returns
LOCAL_APIC_ADDR for x86. It also adds a weak default implementation
which returns 0 if platform does not support LAPIC. This is being
done in preparation to move all ACPI table support in coreboot out of
arch/x86.
BUG=b:155428745
Change-Id: I4d9c50ee46804164712aaa22be1b434f800871ec
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
ACPI_SATA_GENERATOR is currently used to include sata.c in
ramstage. However, there is no need to guard this inclusion using a
separate Kconfig. All other files that deal with ACPI tables are
included based on the state of HAVE_ACPI_TABLES. This change includes
sata.c in ramstage if HAVE_ACPI_TABLES is selected. If the ACPI
function isn't used, linker will optimize it out.
BUG=b:155428745
Change-Id: I9a319cfe7c3f973b15ccbd0f13bd1ed07571a398
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
I rushed CB:40895 in to fix a bug only to introduce another. xhci_init()
no longer crashes, but it doesn't correctly initialize the XHCI
controller either, and unfortunately the error messages are all hidden
behind USB_DEBUG. This patch fixes the incorrect address calculation to
what it was before CB:39838.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I14293e2135108db30ba6fd2efea0573fe266fa37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
AMD has rewritten AGESA (now at v9) for direct inclusion into UEFI
build environments. Therefore, unlike the previous Arch2008
(a.k.a. v5), it can't be built without additional source, e.g. by
combining with EDK II, and it has no entry points for easily
building it into a legacy BIOS.
AGESA in coreboot now relies on the FSP 2.0 framework published
by Intel and uses the existing fsp2_0 driver.
* Add fsp_memory_init() to romstage.c. Although Picasso comes out
of reset with DRAM alive, this call is added to maximize
compatibility and facilitate internal development. Future work
may look at removing it. AGESA reports the memory map to coreboot
via HOBs returned from fsp_memory_init().
* AGESA currently sets up MTRRs, as in most older generations.
Take ownership back immediately before running ramstage.
* Remove cbmem initialization, as the FSP driver handles this.
* Add chipset_handle_reset() for compatibility.
* Top of memory is determined by the FSP driver checking the HOBs
passed from AGESA. Note that relying on the TOM register happens
to be misleading when UMA is below 4GB.
BUG=b:147042464
TEST=Boot trembyle to payload
Change-Id: Iecb3a3f2599a8ccbc168b1d26a0271f51b71dcf0
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34423
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If the current pad configuration can not be defined using standard
macros from the gpio_defs.h [1], then the intelp2m utility generates
"advanced" _PAD_CFG_STRUCT() macros. However, often this configuration
in the vendor’s firmware is erroneous. Change the extended macros to
standard ones taking into account the information based on the schematic
diagram and the previous GPIO configuration for FSP-M [2].
[1] src/soc/intel/common/block/include/intelblocks/gpio_defs.h
[2] src/mainboard/ocp/tiogapass/skxsp_tp_gpio.h
Change-Id: I56e45b1df77acbdd67e6325c3745a7ad137f8805
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1
registers values from the inteltool dump, is more understandable and
makes the code much cleaner. The gpio.h file with PAD_CFG macros was
automatically generated using the util/intelp2m [1] utility:
./intelp2m -p lbg -file tiogapass/vendorbios/inteltool_gpio.log
According to the documentation [2], the Host Software Pad Ownership
register only affects the pads that are configured as input (GPI).
The intelp2m utility takes this into account when converting macros
and ignores bits from this register for the corresponding pads.
[1] https://review.coreboot.org/c/coreboot/+/35643
[2] Intel Document Number: 549921
Change-Id: I21e98721e58b00be9196927837daa2b5d2560822
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40731
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to changes in the soc/xeon_sp code [1,2], server motherboards
with Lewisburg PCH can use the soc/intel/common/gpio driver to configure
GPIO controller. This patch adds pads configuration map, which has the
format required by the GPIO driver. The data for this was taken from the
inteltool register dump with AMI firmware. The gpio.h file with pad
configuration was generated automatically using the util/intelp2m [3]:
./intelp2m -raw -p lbg -file tiogapass/vendorbios/inteltool_gpio.log
[1] https: //review.coreboot.org/c/coreboot/+/39425
[2] https: //review.coreboot.org/c/coreboot/+/39428
[3] https: //review.coreboot.org/c/coreboot/+/35643
Change-Id: I818d040fa33f3e7b94b73c9bbbafca5df424616d
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39427
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since CPX FSP headers are not released yet, populate certain
settings with hard-coded offsets. Provided values are probably
not correct and I do not understand what they mean and there is
no documentation available yet. However they were found to work
to a certain degree.
TEST=tested on OCP Sonora Pass EVT
Change-Id: I0f78cde69cb8a49a388a412b97bf8713e5b380ea
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40554
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The AMD64 Architecture Programmer's Manual, Volume 2: Systems
Programming says the following about variable MTRRs:
Variable Range Size and Alignment.
The size and alignment of variable memory-ranges (MTRRs) and I/O ranges
(IORRs) are restricted as follows:
* The boundary on which a variable range is aligned must be equal to the
range size. For example, a memory range of 16 Mbytes must be aligned on a
16-Mbyte boundary (i.e., naturally aligned).
* The range size must be a power of 2 (2^n , 52 > n > 11), with a minimum
allowable size of 4 Kbytes. For example, 4 Mbytes and 8 Mbytes are
allowable memory range sizes, but 6 Mbytes is not allowable.
Print out errors if these conditions are violated. I didn't assert since
`set_var_mtrr` can be used in boot block before the serial console is
enabled.
BUG=b:147042464
TEST=Boot trembyle and see MTRR errors:
MTRR Error: base 0xcc800000 must be aligned to size 0x1000000
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8b8c734c7599bd89cf9f212ed43c2dd5b2c8ba7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40762
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Let's gather some documentation ideas for the season of docs. I reused
the project ideas style (thanks Patrick). Feel free to add yourself as a
mentor here. Also if you have more ideas, please add them to the
document.
Change-Id: I72221cbd53b99cdc946109753cf72af9c865a1e5
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40662
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add GPIO_PCH_WP (GPP_C11) to associate GPP_PCH_WP with community
zero.
TEST=Build coreboot, flash, boot to
and log into kernel, execute "wp enable" in console,
execute "crossystem" at kernel prompt and verify that "wpsw_cur"
shows as being "1", Execute "wp disable" in console, execute
"crossystem" at kernel prompt and verify "wpsw_cur" is 0.
Change-Id: Ie4ae1365a7611b8be3e795798c171e3f7ea9e417
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40744
Reviewed-by: Usha P <usha.p@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
An array of 64bit integers is passed to acpi_dp_add_integer_array() but
it is not const so can't take a const array without a compiler error.
The function does not modify the array so it can be made const without
breaking anything and allowing a const array to be passed in the future.
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I98ecdaef5ddfa2026390e2812f5ea841ee51f073
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40882
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently if a child table is created and added to a property list
without adding any properties to that child it will generate an
empty package. For example:
struct acpi_dp *dsd = acpi_dp_new_table("_DSD");
struct acpi_dp *prop = acpi_dp_new_table("PROP");
acpi_dp_add_child(dsd, "dsd-prop", prop);
acpi_dp_write(dsd);
Results in an empty PROP package:
Name (_DSD, Package (2)
{
ToUUID("dbb8e3e6-5886-4ba6-8795-1319f52a966b")
Package (1) {
Package (2) {
"dsd-prop",
"PROP"
}
}
}
Name (PROP, Package (0)
{
}
Empty packages don't seem to be explicitly forbidden, but they don't
serve a purpose with device properties. Instead, if packages without
any properties or children are skipped then this empty package is not
written and the added child property can refer to another property that
is already defined.
This allows creating property references to existing tables, which can
save duplication and namespace collision issues with nested properties.
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I9fee2ceb8a4496b90c7210533eee8c2b186cdfff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
BUG=b:152019429
BRANCH=None
TEST=1. provision dram_part_num field of CBI
2. modify mainboard - dedede to report DRAM part number from CBI
3. check DRAM part number is correct in SMBIOS for memory device
Change-Id: I509d06a81bd005c5afe6e74a2da2ca408dee7b29
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Separate specific setting to variant from baseboard.
baseboard/romstage.c in current release is only utilized by
careena, we could remove it from the rest of variant build.
BUG=b:154357210,b:154848243
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I658526e44aadc47bdc5538f506a1bfe2e5f20f63
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Fix FSP CAR on platforms that have ROM_SIZE of 32MiB.
CodeRegionSize must be smaller than or equal to 16MiB
to not overlap with LAPIC or the CAR area at 0xfef00000.
Tested on Intel CFL, the new code allows to boot using FSP-T.
Change-Id: I4dfee230c3cc883fad0cb92977c8f5570e1a927c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
LTE module is lost after idle overnight, with this workaround,
host will not initiate U3 wakeup at the same time with device,
which will avoid the race condition.
Disable XHCI LFPS power management.
If the option is set in the devicetree, the bits[7:4] in
XHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated
from default 9 to 0.
BUG=b:146768983
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ib8e5ae79e097debf0c75ead232ddbb2baced2a2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Running commit aee0baf069 on
Facebook fbg1701 results in an error:
VB2:vb2_rsa_verify_digest() ERROR - vboot2 work buffer too small!
ERROR: HASH table verification failed!
The actual vboot structures require more space.
Workbuffer size needs to be increased.
We didn't determine the commit causing the issue because this change
fixes the issue.
BUG=N/A
TEST=Build and boot Facebook fbg1701
Change-Id: I5caebc643eb493f4285c2f2fc164ff3a5d35e24e
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Show a basic example of how unit testing can be applied for the coreboot
project. Add a test harness for lib/string.c module.
TEST=Install cmocka via appropriate command:
sudo apt-get install -y libcmocka-dev
sudo emerge dev-util/cmocka
yum install libcmocka-devel
* Build and run unit tests via `make unit-tests`
* Check the output to see that tests passed.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: Ibf5554d1e99a393721a66bdd35af0122c2e412c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Add a subsystem which will be used for writing, building and running
unit tests for different coreboot's modules. This work is built using
Cmocka unit testing framework. Description of what unit testing means
(for the author) and how unit testing framework evaluation was performed
may be found in Documentation/technotes/2020-03-unit-testing-coreboot.md
Makefiles structure is very similar to this used for building coreboot
images. Every directory has its own Makefile.inc were tests' names,
sources, subdirs and multiple other test-related attributes are defined
in form of variables.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: I9b0220b84b9a6e448476ca3eb3ccccc5fb829ad1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Unlike prior AMD devices, picasso cannot rely on the cache-as-RAM
setup code to properly enable MTRRs. Add that capability to the
bootblock_c_entry() function. In addition, enable an MTRR to cache
(WP) the flash boot device and another for WB of the non-XIP bootblock
running in DRAM.
BUG=b:147042464
TEST=Boot trembyle to payload and make sure bootblock isn't abnormally
slow.
Change-Id: I5615ff60ca196e622a939b46276a4a0940076ebe
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38691
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id 55154620:
vboot: Add screens for recovery using disk
to commit id 3aab3014:
vboot: Convert reboot-related errors to vboot2-style
This brings in 3 new commits.
Change-Id: I75be535e0b0f8080366b98e5ae2007452ad51738
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40845
Reviewed-by: Joel Kitching <kitching@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This CL adds support to fill PcieRpClkReqDetect UPD from devicetree.
Filling this UPD will allow FSP to enable proper clksrc gpio
configuration.
BUG=None
BRANCH=None
TEST=Build and boot tglrvp.
Change-Id: Iad0ba94fea019623a5b98fff0cb4a2cd1d2a7bd7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
This patch adds psys_pmax calculation. There are two types of power
sources. One is barrel jack and the other is USB TYPE-C. The voltage
level is fixed for a barrel jack while TYPE-C may vary depending
on power ratings. We need to get voltage information from
EC and calculate correct psys_pmax value. The psys_pmax needs to be
set before FSP-S since FSP-S will handle the setting passing to pcode,
so move the routine ahead to variant_ramstage_init.
BUG=b:151972149
TEST=emerge-puff coreboot chromeos-bootimage
check firmware log and ensure psys_pmax is passed to FSP
check the data from dump_intel_rapl_consumption in the OS and
ensure the power data is close to an external power meter.
Change-Id: Iff767d4b44a01e766258345545438a54a16d1af5
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
smbios_slot_{type,data_width,length,designation} used for smbios_type_9 needs "smbios.h"
Also use already defined 'smbios_type11' in "smbios.h".
This will also include <smbios.h> in "static.c" file, this we can remove indirect includes of
<smbios.h> in "chip.h"
Change-Id: Id412a504da2fd75648636febd150356569e07935
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40310
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The stuffed resistor straps are weaker compared to the internal pull-up.
This can cause the GPIO to read '1' always. Remove the internal pull-up.
Also read the GPIO only on the boards where the board version is
populated.
BUG=b:154301008
TEST=Build and boot the mainboard.
Change-Id: Ib640211b9f50dfb0174a570eda1625bacbebb855
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
1. Add support as per the schematics
2. Add 2 Ports and 2 Endpoints
3. Add support for OTVI8856 and OTVI5676
4. Add ON and OFF logic as Power Rails are same for both sensor
BUG=None
BRANCH=None
TEST=Build and Boot waddledoo board and able to capture image
using world facing camera.
Change-Id: Ic8687bce4896d9fc17b2190b8d11618af3515cc1
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The QEMU XHCI driver does not implement the Port Change Detect bit
in the USBSTS register. As a result no devices are attached without
looking at each port individually.
Detect this as a quirk based on the QEMU XHCI controller PCI ID,
and apply it to the root hub quirk list so it can get used by the
generic hub driver to skip this check.
With this change an attached USB mass storage device is detected and
able to boot when supplied to qemu:
-drive if=none,id=usbmsc,format=raw,file=/tmp/disk.img
-device qemu-xhci,id-xhci
-device usb-storage,bus=xhci.0,drive=usbmsc
Change-Id: I6689cb1dbb24c93d45f5c5ef040b713925d07588
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39839
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support to generate ACPI operations to get/set/clear RX/TX GPIOs.
BUG=b:152936541
TEST=Build and boot the mainboard. Ensure that there are no errors in
the coreboot logs regarding unsupported ACPI GPIO operations.
Change-Id: Ibc4846fbd9baf4f22c48c82acefed960669ed7d4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update UPD IIO bifurcation at run-time according to different Riser
cards. For detail please reference
Facebook Server Intel Motherboard v4.0, Sec. 10.1.2 Riser card types.
With the engineering build FSP, it can only configure IIO for
one socket so my local test needs to remove all socket1 elements
from tp_iio_bifur_table.
This change relies on [1] and need to add GPP_C15 and GPP_C16 to
early_gpio_table for gpio configuration in bootblock.
[1] https://review.coreboot.org/c/coreboot/+/39427/
Tested=OCP Tioga Pass can see socket0 IIO being updated with
an engineering build FSP.
Change-Id: I8e63a233a2235cd45b14b20542e6efab3de17899
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1
registers values from the inteltool dump, is more understandable and
makes the code much cleaner. The gpio.h file with PAD_CFG macros was
automatically generated using the util/intelp2m [1] utility:
./intelp2m -p lbg -file cedarisland/vendorbios/inteltool_gpio.log
According to the documentation [2], the Host Software Pad Ownership
register only affects the pads that are configured as input. The
intelp2m utility takes this into account when converting macros and
ignores bits from this register for the corresponding pads.
[1] https://review.coreboot.org/c/coreboot/+/35643
[2] Intel Document Number: 549921
Change-Id: Id671a9021a8313d8c3359b89c2934b929bcab1a4
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40736
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to changes in the soc/xeon_sp code [1,2], server motherboards
with Lewisburg PCH can use the soc/intel/common/gpio driver to configure
GPIO controller. This patch adds pads configuration map, which has the
format required by the GPIO driver. The data for this was taken from the
inteltool register dump with vendors firmware. The gpio.h file with pad
configuration was generated automatically using the util/intelp2m [3]:
./intelp2m -raw -p lbg -file cedarisland/vendorbios/inteltool_gpio.log
[1] https: //review.coreboot.org/c/coreboot/+/39425
[2] https: //review.coreboot.org/c/coreboot/+/39428
[3] https: //review.coreboot.org/c/coreboot/+/35643
Change-Id: I90b91e6dbf8c65c747d0e0d94c61023e610f93ab
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Most payloads, like GRUB, SeaBIOS and Linux, are able to initialize the
PS/2 keyboard themselves, so coreboot does not need to initialize it.
Therefore, this option should not be hard-coded for the mainboard, and
be left for the user to select.
Change-Id: Ibfb7efa22c525e60399afc198af6632330faaac3
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Since commit 6aa8c5bc (drivers/pc80: Do not initialize PS2 keyboard by
default), the Kconfig option `DRIVERS_PS2_KEYBOARD` already defaults to
`n`. So, remove it here, as this option should be user selectable
anyway depending on the payload.
Change-Id: I3d08fb6bbb3e9d53fd2fed96f26679e8b1e73f8c
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Most payloads, like GRUB, SeaBIOS and Linux, are able to initialize the
PS/2 keyboard themselves, so coreboot does not need to initialize it.
Therefore, this option should not be hard-coded for the mainboard, and
be left for the user to select.
Change-Id: Iac835d2e7a3232f8e5c76f10984ae3f172f9c0ca
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change enables support for em100 for Picasso platform. Since
em100 requires lower SPI speed, this change configures speed in all
modes as 16MHz.
BUG=b:147758054,b:153675510
BRANCH=trembyle-bringup
TEST=Verified that em100 works fine on trembyle.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib5ea1fe094fda9b8dba63e94b37e61791629564f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40825
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a helper sb_spi_init() that makes all the required
calls for configuring SPI to ROM.
BUG=b:147758054,b:153675510
BRANCH=trembyle-bringup
TEST=Verified that SPI configuration is correct for trembyle.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic5b395a8d3bdab449c24b05d1b6b8777e128b5e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40824
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds enums for spi_read_mode and spi100_speed in
preparation for adding these to chip.h in follow-up CLs. This makes it
easier to reference what the mainboard is expected to set for these
SPI configs.
BUG=b:147758054,b:153675510
BRANCH=trembyle-bringup
TEST=Verified that SPI configuration is correct for trembyle.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7f9778b41bd059a50f20993415ebd8702a1ad58e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40823
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 285975dbba.
Reason for revert: VB2_RECOVERY_TRAIN_AND_REBOOT was never meant to have
any special effect on memory training behavior. It was just supposed to
be a "reboot automatically after reaching kernel verification" recovery
reason. On x86 devices this was used to prime the separate recovery
MRC cache in the factory (make sure it is initialized before shipping).
This isn't used on Kukui anyway, but in order to make sure nobody copies
this code and keep the behavior consistent between platforms, let's
remove it.
Change-Id: I5df5e00526e90cb573131de3c8bac9f85f4e3a5f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40623
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable aspeed's function that port 80h direct to GPIO for LED display,
refer to section 9.4 Port 80h Direct to GPIO Guide of aspeed's
Application Design Guide, also configure GPIO to UART for output
serial console messages.
Tested=Check if port 80h LED debug card can display POST codes at
early stage, and serial console can see the related messages.
Change-Id: I087d5a81b881533b4550c193e4e9720a134fb8e7
Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40481
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the trondo variant of the volteer reference board by copying the
template files to a new directory named for the variant.
BUG=b:154678884
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_TRONDO
Change-Id: Ie4f9bfe4798e14f91c6cb439f5c5ab2b9ea52b51
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40686
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
memcpy() is meant to be used on normal memory and often implemented with
architecture-specific optimizations to make that as performant as
possible. MMIO registers often have special access restrictions that may
be incompatible with whatever memcpy() does. For example, on arm64 it
uses the LDP (load pair) to load 16 bytes at a time, which makes 4-byte
MMIO registers unhappy.
This patch removes the caching of the XHCI capreg registers and changes
it back to a pointer. The CAP_GET() macro is still accessing a full
(non-bitfield) uint32_t at the end so this should still generate a
4-byte access (which was the goal of the original change in CB:39838).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id058c8813087a8e8cb85f570399e07fb8a597108
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
It seems that all SC7180 boards we have can well handle 37.5MHz of SPI
flash speed, so bump that up from the current 25MHz so that we don't
leave boot speed on the table. (The next step would be 50MHz which
currently doesn't work on all boards so we're not going there yet.)
BUG=b:117440651
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id6e98fcbc89f5f3bfa408c7e8bbc90b4c92ceeea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Looks like 5 is a valid system type, as Google Beltino and Slippy are
using it. According to comments on these mainboards' code, this value
corresponds to ULT systems. So, add it to the comment on the pei_data
struct, which was likely copied from Sandy Bridge and was not updated.
Change-Id: I3654bb6022839dba3e1499cf43e8beaa97d1def1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
This change adds a Kconfig option PSP_UNLOCK_SECURE_DEBUG which
when enabled includes secure debug unlock blobs and sets the required
softfuses and options for amdfwtool. By default this is set to 'N'.
BUG=b:154880818
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I47d8af67989b06242d662c77b7d9db97f624edd5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Add LPC read/write functions for access aspeed's memory, also
create config data table to config memory and SIO. These
functions are used at early stages to configure devices.
Signed-off-by: Bryant Ou <Bryant.Ou.Q@gmail.com>
Change-Id: Ib59c29a042b2c7bf196b8a5bd5218704d8075855
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40483
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It replicates the functionality of savedefconfig because back when the
script was added, savedefconfig didn't work for us. It now does, is
the official way of doing things, is recommended in our documentation
and is also a fair bit faster.
Change-Id: Ia8e0377537ff7cd638c564037ea6a77b01a87243
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change updates Makefile.inc to use a helper function set-bit to
set a bit for the soft fuses. It gets rid of the different checks that
were done to set soft fuses to magic values in different places.
This is still not the best way to handle the fuses and instead this
logic should be embedded within the amdfwtool by making it aware of
specific platforms. But until that happens, we want to avoid having to
add PSP_SOFTFUSE setting in various places with different values.
BUG=b:154880818
TEST=Verified that the softfuse values are same with and without this
change.
Change-Id: I73887eb9c56ca5bb1c08d298fa818d698da1080b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40700
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some of the PSP Kconfig options that are prompted to the user should
really be selected by mainboard. This change updates such options to
not make them user-visible any more.
BUG=b:154880818
Change-Id: Iaff02fb1e720e0562b740799593322e59b022212
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
PSPTRUSTLETS_FILE was including a binary for fTPM which according to
BIOS architecture design guide is the firmware enabled TPM. Chrome OS
does not really use firmware enabled TPM. Also, this is an option
which is mainboard dependent.
This change drops the addition of PSPTRUSTLETS_FILE to PSP
directory. If this is something that is required by any mainboard,
there should be a separate Kconfig to include the required files.
BUG=b:154880818
TEST=Verified that trembyle still boots
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Iaa2126c879986d00c921c85fb5cb5257c7065006
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change drops the addition of PUBSIGNEDKEY_FILE to PSP
directory. This file is used to add OEM key for BIOS, however this is
currently unused for upcoming zork board. In the future, if any
mainboard needs this, it can be added based on some Kconfig selection.
BUG=b:154880818
TEST=Verified that trembyle still boots up fine.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Icd97856a94a100898678702d99bbe29b82956004
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40682
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds support in common block HDA driver to add a PCI
device for HDA in SSDT and removes the HDA device from DSDT for
Stoneyridge and Picasso.
_INI method is still retained in stoneyridge since I am unsure why it
was added. In order to support the _INI method, HDA driver makes a
callback hda_soc_ssdt_quirks() to allow SoCs to add any quirks
required for the HDA device. This callback is implemented by
Stoneyridge to provide the _INI method which retains the same
functionality for HDA device.
This makes it easier to ensure that we don't accidentally
make the DSDT and SSDT entries inconsistent w.r.t. ACPI name and
scope.
BUG=b:153858769,b:155132752
TEST=Verified that audio still works fine on Trembyle.
Change-Id: I89dc46b92fdcb785bd37e18f0456935c0e57eff5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40785
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds the following acpigen helpers:
a. acpigen_write_store_op_to_namestr: This generates ACPI code for
storing an ACPI OP to name string
b. acpigen_write_if_lequal_namestr_int: This generates ACPI code for
checking if operand1 and operand2 are equal where operand1 is
namestring and operand2 is an integer.
Change-Id: I84c158361c0725c2927f06be35391e61f627a453
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40783
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
_INI method for AZHD device for Picasso family was just copied from
Stoneyridge as part of initial change. There is no evidence that this
is required for Picasso. Also, removing the _INI method works
perfectly fine. Thus, this change drops the _INI method for AZHD
device on Picasso.
Since the _INI method was the only entity using the OperationRegion
fields, this change also drops the operation region.
BUG=b:155132752
TEST=Verified that audio still works on Trembyle
Change-Id: If42abf91ee5cd47a881b0a3b4ca1916ea5169261
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40782
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds .acpi_name() callback to HDA driver that returns
"AZHD" as the ACPI device name for HDA controller. Since this is now
done by the common HDA driver, this change also removes the HDA device
name returned by stoneyridge in chip.c.
BUG=b:153858769
Change-Id: I89eaa799518572f3c46c7ce9ef8dd3f85daa12bb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40781
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since `commit 0ee9b14c09c` the SPD array is set to NULL if no
DIMM is present. This causes failure due to an unconditional use
of `blk.spd_array[i]`, : i={0,1}.
This validates the spd_array is non-NULL before use otherwise it
sets the DIMM as not present.
Puff fails boot with the following log:
```
...
SPD: banks 16, ranks 2, rows 16, columns 10, density 8192 Mb
SPD: device width 8 bits, bus width 64 bits
SPD: module size is 16384 MB (per channel)
ASSERTION ERROR: file 'src/soc/intel/cannonlake/cnl_memcfg_init.c', line 47
```
BUG=b:155220125
BRANCH=none
TEST=none
Change-Id: I5f47c849344951d53fa8c67e779b7c46d632d124
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40820
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The original plan for Picasso was to combine the features of bootblock
with romstage due to its unique way of coming out of reset. Early in
development, all bootblock support was removed from the directory.
All Picasso designs will now use a bootblock as their first stage. The
reason being that it requires less invasive changes than using a hybrid
romstage.
Add a basic bootblock back to the directory, and compatible with the
design of lib/bootblock.c. The files support RESET_VECTOR_IN_RAM
and add appropriate settings in Kconfig. Make Makefile.inc calculates
the size and base of bootblock from known parameters.
* Future work may attempt to streamline this further, in conjunction
with changes in amdfwtool. See b/154957411.
BUG=b:147042464, b:153675909
Change-Id: I1d0784025f2b39f140b16f37726d4a7f36df6c6c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37490
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for devices with the reset vector pointing into DRAM. This
is a specific implementation that assumes a paradigm of AMD Family 17h
(a.k.a. "Zen"). Until the first ljmpl for protected mode, the core's
state appears to software like other designs, and then the actual
physical addressing becomes recognizable.
These systems cannot implement cache-as-RAM as in more traditional
x86 products. Therefore instead of reusing CAR names and variables,
a substitute called "earlyram" is introduced. This change makes
adjustments to CAR-aware files accordingly.
Enable NO_XIP_EARLY_STAGES. The first stage is already in DRAM, and
running subsequent stages as XIP in the boot device would reduce
performance.
Finally, add a new early_ram.ld linker file. Because all stages run in
DRAM, they can be linked with their .data and .bss as normal, i.e. they
don't need to rely on storage available only at a fixed location like
CAR systems. The primary purpose of the early_ram.ld is to provide
consistent locations for PRERAM_CBMEM_CONSOLE, TIMESTAMP regions, etc.
across stages until cbmem is brought online.
BUG=b:147042464
TEST=Build for trembyle, and boot to ramstage.
$ objdump -h cbfs/fallback/bootblock.debug
Idx ,Name ,Size ,VMA ,LMA ,File off Algn
0 ,.text ,000074d0 ,08076000 ,08076000 ,00001000 2**12
1 ,.data ,00000038 ,0807d4d0 ,0807d4d0 ,000084d0 2**2
2 ,.bss ,00000048 ,0807d508 ,0807d508 ,00008508 2**2
3 ,.stack ,00000800 ,0807daf0 ,0807daf0 ,00000000 2**0
4 ,.persistent ,00001cfa ,0807e2f0 ,0807e2f0 ,00000000 2**0
5 ,.reset ,00000010 ,0807fff0 ,0807fff0 ,0000aff0 2**0
6 ,.debug_info ,0002659c ,00000000 ,00000000 ,0000b000 2**0
7 ,.debug_abbrev ,000074a2 ,00000000 ,00000000 ,0003159c 2**0
8 ,.debug_aranges,00000dd0 ,00000000 ,00000000 ,00038a40 2**3
9 ,.debug_line ,0000ad65 ,00000000 ,00000000 ,00039810 2**0
10 ,.debug_str ,00009655 ,00000000 ,00000000 ,00044575 2**0
11 ,.debug_loc ,0000b7ce ,00000000 ,00000000 ,0004dbca 2**0
12 ,.debug_ranges ,000029c0 ,00000000 ,00000000 ,00059398 2**3
Change-Id: I9c084ff6fdcf7e9154436f038705e8679daea780
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35035
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Setting the default values for GPIO community power management, causes
issues in detecting TPM interrupts. So to avoid that GPIO PM has to be
disabled in devicetree. But for S0ix it is needed. This patch implements
a workaround in ASL code to enable GPIO PM on S0ix entry and disable it
on S0ix exit.
This patch adds the following three platform specific methods.
1. MS0X to enable power management features for GPIO communities on
entry and on exit, it disables them.
2. MPTS to enable power management features for GPIO communities when
preparing to sleep.
3. MWAK to disable power management features for GPIO communities on
waking up.
BUG=b:148892882
BRANCH=none
TEST="Boot with this change on volteer proto1 and check for GPIO
community config with debugger"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: If522c82c0069a4bf5738beb73a2b4f11ed6f51d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40261
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds GPID, a helper method to look up GPIO community ID for
an index.
This patch also includes Intel's common GPIO ASL code. CGPM method in
the common code uses the GPID method introduced in this patch.
BUG=b:148892882
BRANCH=none
TEST="BUILD volteer and ripto"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Id6a00fb8adef0285d6bbc35cd5a44539bd3be6b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40478
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change enables the use of AMD common block SATA driver for
Picasso. Since the common driver provides ACPI device name and PCI
device for SATA in SSDT, these are removed from picasso chip.c and
sb_pci0_fch.asl.
BUG=b:153858769
TEST=Verified that "STCR" device is correctly reported on trembyle in
SSDT.
Change-Id: Icfdcf9f5e08820b565aa9fcdd0cdc7b5c9eadcd5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40770
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds support in common block SATA driver to add a PCI
device for SATA in SSDT and removes the SATA device from DSDT.
This makes it easier to ensure that we don't accidentally
make the DSDT and SSDT entries inconsistent w.r.t. ACPI name and
scope.
BUG=b:153858769
Change-Id: I16ac36d997496ff33c5b44ec9bd2731b2b8799eb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40769
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds .acpi_name() callback to SATA driver that returns
"STCR" as the ACPI device name for SATA. Since this is now done by the
common SATA driver, this change also removes the SATA device name
returned by stoneyridge in chip.c.
BUG=b:153858769
Change-Id: I5e0998be3016febbb3b0e91940750a38edb6a9e7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40768
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
sata.c was being added to ramstage based on the selection of
CONFIG_SOC_AMD_COMMON_BLOCK_HDA which is not correct. This change
fixes the error by including sata.c based on selection of
CONFIG_SOC_AMD_COMMON_BLOCK_SATA.
BUG=b:153858769
Change-Id: I5d23e5817872ddbb3d8d4f7dcabbaafcee4d51f4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40766
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implements mainboard_get_dram_part_num() to override dram part number
with a part number read from CBI.
BUG=b:146464098
TEST="emerge-volteer coreboot chromeos-bootimage", flash volteer, boot
and log into kernel, execute "mosys memory spd print id" and verify that
the memory part number from the cbi gets displayed properly.
Change-Id: I3a20691f601cb513ee0936c8d141233c3d06db3d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Pointer passed to print_spd_info() from meminit.c needs to be
dereferenced first, so this change dereferences it.
BUG=b:154352883
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
volteer, login to kernel and execute the following cbmem command:
localhost ~ # cbmem -c | grep LPDDR4X
and verify it returns "SPD: module type is LPDDR4X"
Change-Id: I5ff64121f0d50947c4946e9e02460dfb7319d01a
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Since CB:40389, all platforms with CONFIG_VBOOT_EARLY_EC_SYNC need to
write back secdata in romstage. Those platforms currently all happen to
have CONFIG_VBOOT_SEPARATE_VERSTAGE set as well, but there's no official
dependency between those options. Change the Makefile to unconditionally
build the secdata access routines for romstage so that this would work
on other platforms as well.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0b3c79e9bb8af9d09ef91f5749953ca109dd2a40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
intel_igd_get_controller_info() does not need to modify the device
structure. Hence, this change makes the struct device * parameter to
intel_igd_get_controller_info() as const.
Change-Id: Ic044a80e3e2c45af6824a23f3cd0b08b94c0f279
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change makes the struct device * param to callback function
called by i2c_generic_fill_ssdt() as const. This is in preparation to
make struct device * param to fill_ssdt as const.
Change-Id: I7556b672a7b0172ded44747af394f5b32b6209aa
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40707
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
h8_has_bdc() and h8_has_wwan() do not need to modify the device
structure. Hence, this change makes the struct device * parameter to
these functions as const.
This is being done in preparation to make struct device * parameter to
fill_ssdt as const.
Change-Id: Id3d65d2de7b5161b0e7cff26055c00d5dae967dc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40706
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds uid parameter to drivers_ipmi_config that can be used
by ipmi_ssdt() to store the uid value to be used by
ipmi_write_acpi_tables. This allows to remove the requirement in
ipmi_ssdt() to update dev->command. This is being done in preparation
to make the struct device * parameter to fill_ssdt as const.
Change-Id: Ieb41771c75aae902191bba5d220796e6c343f8e0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40705
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
acpi_device_uid() and acpi_device_write_uid() do not need to make
changes to the device structure. Thus, this change marks struct
device * parameter to these functions as const.
Change-Id: I3755223766c78f93c57ac80caf392985cfd5c5e5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40702
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change:
1. Adds PCI device for graphics controller in ACPI SSDT tables using
acpi_device_write_pci_dev().
2. Gets rid of IGFX device from picasso acpi/northbridge.asl.
This makes it easier to ensure that we don't accidentally
make the DSDT and SSDT entries inconsistent w.r.t. ACPI name and
scope.
BUG=b:153858769
Change-Id: I3a967cdc43b74f786e645d3fb666506070851a99
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change selects common block graphics driver for Picasso and also
adds PCI ID for Family 17h graphics controller to the graphics
driver.
Since the common driver provides .acpi_name() callback for graphics
device, soc_acpi_name() no longer needs to provide the ACPI name for
graphics device.
BUG=b:153858769
Change-Id: Id3ffcb05d8f8a253a0b27407d52d7907c507cabb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change adds a common graphics block device driver for AMD
SoCs. In follow-up CLs, this driver will be utilized for Picasso.
This driver is added to enable ACPI name and SSDT generation for
graphics controller.
BUG=b:153858769
Change-Id: I45e2b98fede41e49158d9ff9f93785a34c392c22
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This change adds all the missing PCI device IDs for AMD Family
17h. IDs that were already present are updated to include _FAM17H_ in
the name instead of _PCO_ and _DALI_. This ensures that the PCI IDs
match the family and models as per the PPR. In cases where the
controller is present only on certain models, _MODEL##H_ is also
included in the name.
BUG=b:153858769
BRANCH=None
TEST=Verified that trembyle and dalboz still build.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ia767d32ec22f5e58827e7531c0d3d3bac90d3425
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
IOMMU for AMD Family 17h Model 10-20h uses the same PCI device ID
0x15D1. This change updates the name to indicate that the PCI device
ID is supported for FP5(Model 18h) and FT5(Model 20h).
BUG=b:153858769
BRANCH=None
TEST=Trembyle and dalboz still build.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I17c782000ed525075a3e438ed820a22d9af61a26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This is missing configuration of Wiloc projects.
Following Wilco projects configuration. CB:32436
The power architecture on this platform is different than most of our
other x86 devices and needs some special handling to ensure it powers
up again after an EC reset.
BUG=b:150165131
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I6da89de9401793a4e5c56a23c1018527819718cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40663
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, Deltaur’s I2C speed has not been tuned yet, so slow down
the H1 I2C to avoid I2C error for short term.
Error logs:
Reading cr50 TPM mode
I2C receive timeout
I2C read failed: bus 3 addr 0x50
BUG=b:154310066
TEST=Check H1 has no I2C error occurring and can be updated by gsctool.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I85a63c1ab9a51d254873377a36d56823af11f0a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40644
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to doc 621880, it suggests setting 40 ohm in byte 185 in extCSD.
This commit provides _DSM method for driver to query driving strength.
TEST=mmc extcsd read |grep HS_TIMING and found bit[7:4] is set to 4
BUG=b:154159888
Signed-off-by: Kane Chen <kane.chen@intel.com>
Change-Id: I1b4df8b0d1d2cad3a7f521ad47ee5a4b3320c767
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Populate SMBIOS type 17 tables using data from SPD and read via IOSF.
Refactor print_dram_info() to pass thru SPD data and channel/speed info.
Move call to print_dram_info() after cbmem initialization so the SMBIOS
data has somewhere to go.
Test: build/boot google/swanky, verify via dmidecode.
Change-Id: I1c12b539c78d095713421b93115a4095f3d4278d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add a FMAP which supports SMMSTORE and non-ChromeOS payloads,
since GeminiLake-based devices like Octopus cannot use an
automatically-generated FMAP due to strict layout requirements.
Change-Id: Iebacbea5b3a782b2abf1d6e28acd21b87dc9402b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40596
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Including i915.h just for the GMA/SSDT related functions means
dragging along all of i915_reg.h as well, which is problematic
since some platforms (like Apollo Lake) use overlapping symbols.
To avoid this conflict, break out the GMA/SSDT bits into their
own header which can be included without conflict.
Change-Id: I73fb7ef01abaafdcdbc44f1e3f5eb1883fc31616
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Allow a custom boot splash to be used with UefiPayloadPkg:
- remove Kconfig guards restricting to CorebootPayloadPkg
- set destination path for logo file based on bootloader selected
Test: build/boot qemu with UefiPayloadPkg with custom boot logo
Change-Id: Ia0a10d1528f516f6b9d3645b83be0fb4e85bc348
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Recent changes to upstream edk2 necessitate ensuring
that Tianocore's submodules exist and are up to date,
otherwise building UefiPayloadPkg will fail.
Change method used to detect a dirty tree so that initialized
submodules do not taint the result.
Test: build qemu with Tianocore UefiPayloadPkg option successfully.
Change-Id: Ie2541f048966ec0666d8196508ccdb6c5f089de6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Allow to write protect only the WP_RO region in case of enabled VBOOT.
One can either lock the boot device in VERSTAGE early if VBOOT is enabled,
or late in RAMSTAGE. Both options have their downsides as explained below.
Lock early if you don't trust the code that's stored in the writeable
flash partition. This prevents write-protecting the MRC cache, which
is written in ramstage. In case the contents of the MRC cache are
corrupted this can lead to system instability or trigger unwanted code
flows inside the firmware.
Lock late if you trust the code that's stored in the writeable
flash partition. This allows write-protecting the MRC cache, but
if a vulnerability is found in the code of the writeable partition
an attacker might be able to overwrite the whole flash as it hasn't
been locked yet.
Change-Id: I72c3e1a0720514b9b85b0433944ab5fb7109b2a2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Introduce boot media protection settings and use the existing
boot_device_wp_region() function to apply settings on all
platforms that supports it yet.
Also remove the Intel southbridge code, which is now obsolete.
Every platform locks the SPIBAR in a different stage.
For align up with the common mrc cache driver and lock after it has been
written to.
Tested on Supermicro X11SSH-TF. The whole address space is write-protected.
Change-Id: Iceb3ecf0bde5cec562bc62d1d5c79da35305d183
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The change applies the DPTF parameters received from the thermal team.
1. Set PL1 Min to 3W
2. Set sample period of TCPU/TSR0/TSR1 to 30 Sec
3. Enable EC_ENABLE_MULTIPLE_DPTF_PROFILES and add trigger points
for tablet mode.
4. Update trigger points of CPU/TSR0/TSR1
BUG=b:154564062, b:154290855
BRANCH=hatch
TEST=build and verified by thermal team.
Change-Id: I87170e63de222487a3bda1217c4ee87a2ec1984f
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
With this patch, the ThinkLight on the ThinkPad X200 can be controlled
through the OS. This was initially done for the X201 in f63fbdb6:
mb/lenovo/x201: Add support for ThinkLight.
After applying this patch, the light can be controlled like this:
echo on >/proc/acpi/ibm/light
echo off >/proc/acpi/ibm/light
Or through sysfs at /sys/class/leds/tpacpi::thinklight
I have tested it on an X200 with Kernel 5.4 and it seems to work fine.
Change-Id: I14752ab33484122248959517e73f96b6783b1f65
Signed-off-by: Stefan Ott <stefan@ott.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Replicate the GPO configurations from OEM BIOS, obtained via inteltool.
Among the GPOs are termination controls for the onboard SCSI buses.
TEST=read/write Maxtor Atlas 10k3 18GB HDD connected to Ultra2 LVD port
Change-Id: I86183acd8e1a830d7639c21ec179fbdbe937f8ee
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38354
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For DDR4, FSP expects channel 0 to set SPD for index 0 and channel 1
to set SPD for index 4. This change adds a helper macro to translate
DDR4 channel # to the index # that the FSP expects.
BUG=b:154445630
TEST=Verified that memory initialization for DDR4 is successful.
Change-Id: I2b6ea2433453a574970c1c33ff629fd54ff5d508
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kane Chen <kane.chen@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Assuming given system is populated with multiple CPUs of same SKUs,
calculate number of threads based on MAX_SOCKET.
This is a stop gap solution until proper way of identifying total
number of sockets is determined.
Change-Id: I7ebad3d57c47b9eeb7d727ffb21bc0a1a84734fd
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Currently FSP-M does not implement the spec completely, e.g it is unable
to use user-provided heap location in CAR. While this is being resolved,
this workaround is a stop-gap solution that allows multi-socket usage.
TEST=tested on OCP Sonora Pass EVT and Intel Cedar Island CRB
Change-Id: Ia2529526a8724cf54377b0bd2339b04fa900815a
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40555
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1) Allows MKBP events from the EC to wake the system from suspend states.
2) Remove EC_HOST_EVENT_MKBP from the EC_SCI_EVENTS mask, so that MKBP
events don't generate an SCI. The EC is also being changed to use host
events to wake up the system, and use the EC_INT_L line for MKBP IRQ
signalling. Otherwise, there would be two IRQs generated for MKBP events.
BUG=b:148976961
BRANCH=firmware-hatch-12672.B
TEST=Verify MKBP events wake system
TEST=Verify MKBP IRQs are run
Change-Id: I8420a996cb1975007cbbbefe9e2f8f1fca91b666
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Shelley Chen <shchen@google.com>
The device is always there, the Chromium OS config always enables it,
so let's mirror that here for a better out of the box experience.
Change-Id: Ic43a314aaed635ae2943df02abc5d163cc3c4ffd
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40658
Reviewed-by: Michael Niewöhner
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When CONFIG_SEPARATE_VERSTAGE=n, all verstage code gets linked into the
appropriate calling stage (bootblock or romstage). This means that
ENV_VERSTAGE is actually 0, and instead ENV_BOOTBLOCK or ENV_ROMSTAGE
are 1. This keeps tripping up people who are just trying to write a
simple "are we in verstage (i.e. wherever the vboot init logic runs)"
check, e.g. for TPM init functions which may run in "verstage" or
ramstage depending on whether vboot is enabled. Those checks will not
work as intended for CONFIG_SEPARATE_VERSTAGE=n.
This patch renames ENV_VERSTAGE to ENV_SEPARATE_VERSTAGE to try to
clarify that this macro can really only be used to check whether code is
running in a *separate* verstage, and clue people in that they may need
to cover the linked-in verstage case as well.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I2ff3a3c3513b3db44b3cff3d93398330cd3632ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch restores the permission check for the kernel space which
was dropped when read_space_kernel was moved from Depthcharge by
CL:2155429.
BUG=chromium:1045217, chromium:1020578
BRANCH=none
TEST=none
Signed-off-by: dnojiri <dnojiri@chromium.org>
Change-Id: If6d487940f39865cadc0ca9d5de6e055ad3e017d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40579
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Romstage is now where software sync is performed for chromebooks.
EFS2 has been ported to romstage from Depthcharge. Puff should
follow.
This patch enables CONFIG_EARLY_EC_SYNC and disables
CONFIG_VBOOT_EC_EFS. EFS2 will be done in romstage.
BUG=b:147298634, chromium:1045217
BRANCH=none
TEST=Verify software sync succeeds on Puff.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I8d7c25f8281496c7adb282f5d4e0fc192d746e3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40390
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id 46ff62c3:
vboot: stop reading from ACPI for wpsw_boot
to commit id 55154620:
vboot: Add screens for recovery using disk
This brings in 37 new commits.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: Ie184cbe6cc18cea540966d5801472ae821ea3e86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40503
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a helper function dev_find_matching_device_on_bus()
which scans all the child devices on the given bus and calls a
match function provided by the caller. It returns the first device
that the match function returns true for, else NULL if no such device
is found.
Change-Id: I2e3332c0a175ab995c523f078f29a9f498f17931
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40543
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change enables support for generating ACPI nodes for I2C tunnel for
any GOOG0012 device that is sitting behind the Chrome EC. It accepts a
config "remote_bus" which allows mainboard to configure the id of the
remote bus that is being tunneled.
BUG=b:154290952
BRANCH=None
TEST=Verified that SSDT node for I2C tunnel behind Chrome EC is
generated correctly.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Icfc0ec3725d7f1d20bcb5cb43a0a23aac72bf4eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change adds scan_static_bus() as .scan_bus() callback for Chrome EC
device which allows scanning of devices sitting behind the EC using
the topology provided by mainboard's devicetree.cb.
BUG=b:154290952
TEST=Verified with follow-up changes that devices behind EC are scanned
correctly.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Id3630db56774fba1e3fc53bf349588c4c585773b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40514
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In ACPI tables, Chrome EC device (CREC - HID GOOG0004) is a child of
EC device (EC0 - HID PNP0C09). However, in coreboot device tree, there
is no separate chip/device for EC0. Thus, acpi_name() needs to return
EC0.CREC as the ACPI name for the Chrome EC device. By returning the
ACPI name as EC0.CREC, all devices that live under Chrome EC device
can simply call acpi_device_path()/acpi_device_scope() to emit the
right path/scope.
In the future, if we ever add a special chip driver for handling EC0
(HID PNP0C09), then the ACPI name for Chrome EC can be fixed to return
CREC.
BUG=b:154290952
TEST=Verified that acpi_device_path()/acpi_device_scope() return the
correct name for Chrome EC device.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Iec4b0226d1e98ddeb0f8ed8b89477fc4f453d221
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40513
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change checks to ensure that device/path passed into any of the
functions in device_const.c is not NULL. Since NULL is not expected to
be passed into these functions, this change adds a die() call in case
the assumption is broken.
Change-Id: I1ad8d2bcb9d0546104c5e065af1eeff331cdf96d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
There are microcodes in .inc format out in the wild which contains
lines with just a comment. So these files look like the following
example:
; External header
dd 000000001h
dd 00000001bh
...
; Data
dd 000000000h
...
The lines with just a comment starts with a ';' and will break
the current awk formatting which is performed to reformat the content
into C code style. As we are just interested in the data we can simply
drop all lines that start with a ';' which sed can do pretty easy.
Change-Id: I9ff5db51667672cffd9d776fb9497962b4a6083a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40566
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The double quotes around the remaining shell parameters '${@:2}' causes
that the provided *.h files in $(CONFIG_CPU_MICROCODE_HEADER_FILES),
which is a space separated list, cannot be broken down to every single
file as needed but stay as a single parameter in the for-loop.
Therefore, the called function 'include_file' will get a single
parameter with all files which will lead to a broken C code in
terms of a wrong #include-syntax. This causes the script to fail.
To fix this remove the double quotes which works just fine.
Change-Id: Iab7b0dc8d850973d6af764899907d383e9ec7743
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Some PCI peripherals, such as discrete VGA adapters, require a great
amount of memory mapped IO. This patch allows the user to select at
build time the bottom IO to leave enough space for such devices.
We cannot calculate this value at runtime because it has to be set
before the PCI devices are enumerated. 0x80000000 has been successfully
boot-tested on A88XM-E (fam15tn), G505S (fam15tn) and AM1I-A (fam16kb).
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: Ie235631231bcb4aeebaff2e0026da2ea9d82f9d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Jenkins does not build using .config.facebook_fbg1701 on new patches.
Rename the config file adding '.mboot_vboot'. Now FACEBOOK_FBG1701
and FACEBOOK_FBG1701_MBOOT_VBOOT are included in Jenkins test result.
BUG=N/A
TEST=Build and boot Facebook fbg1701
Change-Id: Ib54cc29e7ff34553c19fa3502872d6e7aee5fbe8
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40557
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
USB routing has changed on reference schematics after Puff rev1 has
built. This may confuse people trying to c&p devicetree from the Puff.
So add comment to clearly note that there was change, hopefully
preventing c&p errors.
BUG=b:153682207
BRANCH=None
TEST=None
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I5c43a5c04c81b6708c9eeabc48ef11961d7c8561
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40546
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Deltan will be using the integrated Intel GbE for LAN
functionality. Deltaur will not have a LAN port, and so does not need
the GbE region. This patch adds a new FMAP descriptor file which
explicitly supports the GbE region (chromeos-gbe.fmd), and removes the
GbE region from chromeos.fmd. Deltan is then assigned chromeos-gbe.fmd,
and Deltaur is assigned chromeos.fmd.
BUG=b:150165131
TEST=emerge-deltaur coreboot chromeos-bootimage
and use ifdtool -p tgl -t image-delta{ur,n}.bin to make sure FMAP aligns with IFWI
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib93d5ba7f8dbf273ba7c1163022661ede1f44ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add Type-C subsystem power management support for RTD3.
BUG=b:140290596
TEST=Include "tcss.asl" in platform "dsdt.asl" for coreboot build
with the firmware CM. Added acpi debug and booted to kernel. Probed
devices PM_STATE transition from D0 to D3 entry/exit while system at S0.
TBT PCIe root ports: 00:07.0/00:07.1/00:07.2/00:07.3, offset:0xA4, PM_STATE:D3HT.
xhci:00:0d.0, offset:0x74, PM_STATE:D0D3.
dma:00:0d.2/00.0d.3, offset:0x84, PM_STATE:PMST.
Verified xhci/dma/pcie root ports power runtime_status to be suspended and suspended
time tick through /sys/bus/pci/devices/bus:device:func/power.
Change-Id: I127d3700ad426a44639ee93b4477be6638b42e1b
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The WDB (Write Data Buffer) is a data region in CAR, used as a
scratchpad in the read and write training algorithms of memory
initialization. Both SNB and IVB use this buffer, but HSW does not.
Unlike earlier chipsets, Haswell contains much more in-hardware memory
training machinery, known as REUT (Robust Electrical Unified Testing).
Among other changes, the REUT hardware has a pattern storage buffer,
which renders the need for a pattern storage buffer in CAR obsolete.
Deprecate the WDB-related parameters in the pei_data structure for
Haswell, as they are leftovers from the previous generation's MRC.
Remove them from the mainboards, and explain why they are not required.
Because the MRC ABI has to remain the same, the layout of pei_data must
not be changed, so rename the WDB parameters instead of deleting them.
Tested on Asrock B85M Pro4, still boots with the MRC from Google Wolf.
Change-Id: I7acc9353a22f8c6f9fe6407617162f35849a79dd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The frequency to be used by UART client is 7.3728MHz, thus define it in
the clock header to be used by the driver.
Tested: UART frequency request by client driver.
Change-Id: I1ced350fe9826ea05b03ffc11aced2c21fe85c9e
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Enable Wifi and Bluetooth for Jasper Lake RVP with following changes:
1. Enable related pci root ports for WLAN and BT
2. Disable unused root ports and clkreq for unused clocks
3. Configure GPIOs properly for M.2 port
BUG=None
BRANCH=None
TEST=Code compiles and able to detect Wifi/BT module on board.
Change-Id: Ifbd07022c05769c04ecd49c81a4430947125b32a
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39933
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Each physical port should have the same group and position for both USB2
and USB3, but puff and its variants use different layout than the
baseboard so they must override PLD.
Ports are split into two groups for front and back, with positions in
each group numbered from left to right.
BUG=b:151579409
BRANCH=none
TEST=PLD_GroupToken and PLD_GroupPosition are set as expected in SSDT.
Change-Id: Ibe19e4faa1fbc7117687d789e9bd5584852a48c0
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add new file to generate ACPI _DSD code for PS2 keyboards. The
following 2 device properties are generated as needed:
function-row-phymap: A list of ordered scancodes for function row.
linux,keymap: Symantically, this is an array of "scancode,keycode"
tuple entries. Each entry teaches linux the keycode corresponding
to a scancode.
Signed-off-by: Rajat Jain <rajatja@google.com>
Change-Id: I5ee05173106a125793e91c263610731543c85472
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
`lib_sysinfo->serial` is a virtual pointer into coreboot tables.
It's not valid across relocation. Accessing the wrong value during
relocation of FILO resulted in a hang with DEBUG_SEGMENT and UART
console enabled. Work around that by caching the whole table entry
locally.
An alternative would be to revise `sysinfo`, to contain no virtual
pointers to anything outside the payload.
Change-Id: I03adaf57b83a177316d7778f7e06df8eb6f9158e
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reto Buerki <reet@codelabs.ch>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
There have been two cases of incompatibilities between overlapping
changes, and they need to be resolved in a single commit to unbreak the
tree:
1. CB:40389 introduced a new use of write_secdata while CB:40359 removed
that function in favor of safe_write.
Follow the refactor of the latter in the code introduced by the former.
2. CB:39849 changed google_chromeec_get_usb_pd_power_info()'s interface
and adapted all its users. Except for duffy and kaisa which were only
added in CB:40223 and CB:40393 respectively, so reapply the patch to
puff's mainboard.c to their mainboard.c files.
Change-Id: Ib8dfcd61bb79e0a487eaa60e719bd93561f2d97a
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This patch adds psys_pmax calculation. There are two types of power
sources. One is barrel jack and the other is USB TYPE-C. The voltage
level is fixed for a barrel jack while TYPE-C may vary depending
on power ratings. We need to get voltage information from
EC and calculate correct psys_pmax value. The psys_pmax needs to be
set before FSP-S since FSP-S will handle the setting passing to pcode,
so move the routine ahead to variant_ramstage_init.
BUG=b:151972149
TEST=emerge-puff coreboot chromeos-bootimage
check firmware log and ensure psys_pmax is passed to FSP
check the data from dump_intel_rapl_consumption in the OS and
ensure the power data is close to an external power meter.
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Change-Id: I8ea01f856411e05a533489280fc2b4a46a1440c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
This is a micro ATX board with a LGA1155 socket and two DDR3 DIMM slots.
Porting was done using autoport and then doing a bunch of manual edits.
Actually, I have the PLUS variant, but they use the same PCB. The only
difference is the capacitor quality.
Working:
- Both DIMM slots
- PS/2 keyboard
- S3 suspend/resume
- Rear USB ports
- Integrated graphics (libgfxinit)
- VGA
- All PCIe ports
- Realtek GbE (coreboot must set the MAC address)
- SATA ports
- Native raminit
- Flashing with flashrom
- Rear audio output
- VBT
- Arch Linux using CorebootPayloadPkg
Untested:
- PS/2 mouse
- The other audio jacks
- EHCI debug
- Front USB headers
- Non-Linux OSes
Change-Id: I385ee72673202d896041209ff2911995307cb6af
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Later EliteBooks use different EC chips and have different EC firmware
interfaces, so rename the document elitebook_series.md to a more
precise name and also do some rewriting.
A link to the code review page for 8760w is also added because the
port for this laptop is not merged yet.
Change-Id: I2f9b8c4e52ed760c16977d16838cca9e490cda05
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch adds voltage and curent parameters in
google_chromeec_get_usb_pd_power_info and remove power parameter. Caller could
use the voltage and current information to calculate charger power rating.
The reason for this change is, some applications need the voltage information
to calculate correct system power eg PsysPmax.
BUG=b:151972149
TEST=emerge-puff coreboot; emerge-fizz coreboot
Change-Id: I11efe6f45f2f929fcb2763d192268e677d7426cb
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Remove explicit setting of iDisp Link parameters. These settings are
related to configuration for the link between HD-Audio controller and
Display unit for purposes of HDMI/DP Audio playback. During PO,
observed that without setting these params display part was not
binding. With the latest code verified that we dont need to explicitly
set these parameters anymore. HDMI/DP audio playback works fine with
default settings.
BUG=b:151451125
BRANCH:none
TEST= build and boot volteer/ripto and verify HDMI/DP audio playback
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ie003d119918d363e2ff9172936b70416fd73c7f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40263
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jairaj Arava <jairaj.arava@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds _DSM Method in LPIT table for entering and exiting
S0ix. This method get injected into DSDT table and called from kernel.
LPIT table is hardcoded in this patch but the proper way to implement
is to use inject_dsdt to make the _DSM methods available for soc's to
implement.
Calling the LPIT table from mainboard here so that with the current
implementation the platforms which do not have lpit support throw
compilation error.
BUG=b:148892882
BRANCH=none
TEST="BUILD"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Ib58f2e33a33bac9cc5f6aca28e85a8066413a5cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Disable dynamic clock gating for the community cr50's IRQ lives on.
That IRQ is pulsed very quickly, and with clock gating enabled pulses
tend to be missed. This is expecially true on the default 0.0.22
firmware that cr50 comes with out of the factory.
BUG=b:154178408 b:154293730
BRANCH=None
TEST=build waddledoo successful and Linux has no TPM IRQ timeout error.
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I2b1b3ee59ebf6adce0653e7550b457e02d3c87df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Configure DRAM population strap GPIO according to the schematics.
Configure an internal pull-up to support the boards in which the strap
is not populated. Read the strap and pass that information to FSP for
memory initialization.
BUG=b:152275658, b:154301008
TEST=Build and boot the mainboard. Ensure that the strap information is
read as expected and passed to FSP.
Change-Id: I69583f35ffc219bae9ce06bd4ba9898ed0d4d21d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39812
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For bit fields with 31 bits (e.g: DEFINE_BITFIELD(MYREG, 30, 0) ),
the calculation of mask value will go overflow:
"error: integer overflow in expression '-2147483648 - 1' of
type 'int' results in '2147483647'".
And for bit fields with 32 bits (e.g: DEFINE_BITFIELD(MYREG, 31, 0) ),
the error will be:
"error: left shift count >= width of type [-Werror=shift-count-overflow]"
To fix these issues, the bit field macros should always use unsigned
integers, and use 64bit integer when creating mask value.
Change-Id: Ie3cddf9df60b83de4e21243bfde6b79729fb06ef
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The samsung-K4U6E3S4AA-MGCL.spd.hex is not used and planed by anyone
yet. On the other hand, the spd content is not correct based on JSL
spec as well.
BUG=b:153426401
TEST=build waddledoo and waddledee successfully.
Change-Id: If71e3ef2e3385378633549bf8709a1cd6ecc0dd3
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
CB:29744 ("util/cbfstool: Add optional argument ibb") added support
for non-ASCII characters for long_options. However, there is a check
later on which errors out since this character is not one of the
commands[i].optstring.
This change adds a function valid_opt() which does the following
things:
1. Checks if the returned optchar is among the list of optstring
supported by the command.
2. Checks if the returned optchar is a valid non-ASCII
option. Currently, we do not maintain a list of non-ASCII options
supported by each command. So, this function returns true if the
optchar returned by getopt_long falls within the allowed range.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I27a4f9af9850e4c892573202904fa9e5fbb64df6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When using default fmd files, base of the fmap region is currently
calculated based on the size and base of previous fmap regions. Since
the existence of any fmap region is dependent on the selection of
certain CONFIG_* parameters, these calculations get complicated. Every
time base is calculated for a region, there need to be checks to see
which of the previous regions really exist. As the regions in default
fmd file are increased, these calculations and the conditional checks
get even more complicated.
This change introduces a Makefile variable FMAP_CURRENT_BASE which is
updated every time a new region is allocated space. This allows using
the same steps for determining the base of any fmap region
irrespective of the state of previous regions.
The way the code is organized it should be possible in the future to
also add a macro to perform the same steps (in case that is possible).
TEST=Verified that coreboot image generated remains unchanged for x86
and ARM boards using the default fmd files.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I2a109462928b6e8b7930bbcc1a1ba45fa85de6ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Depthcharge trusts that our TPM driver is working reliably,
and so should we. Also remove CRC check -- the value returned
by antirollback_read_space_firmware() is dropped in vboot_logic.c
verstage_main(), and vboot handles this check internally.
BUG=b:124141368, chromium:972956
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I5d3f3823fca8507fd58087bb0f7b78cfa49417ab
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
It is not necessary to pass its value around various function calls.
Move it closer to where it is actually used, so as to make it static.
Also, use config_of_soc and flip the branches of the first conditional.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: I5c49c943c87218d4d40d3168bd8b7b900b0ec2e9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39851
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These variables are declared to be arrays of MICROCODE_PATCHES_4K (which
is a struct containing a UINT8 array). However, the actual definitions
of these arrays ignore the wrapping struct and just use the underlying
UINT8 arrays directly, which causes a compiler error when using LTO
because of the type mismatch. Fix the type declaration so that it
matches.
Change-Id: I6bef27507092fe72fe2f836c427ebb2c19009e78
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This array is declared to have length MAX_FF_TYPES (aka 6) in several
other places, so update it here so the length matches. This fixes a
-Wlto-type-mismatch compiler error when using LTO. Extending the length
is harmless, since the only code that uses this array will stop once it
reaches the NULL pointer.
Change-Id: Ie00e969fa8cda88a934bf416c8775f7ae0b2747e
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39014
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
F14GetNbCofVidUpdate() is declared elsewhere to be of type
F_CPU_IS_NBCOF_INIT_NEEDED, which is supposed to return a boolean value
(not an AGESA status). This is fixed in the corresponding f15tn and
f16kb code, so apply the same change here. This fixes a compiler error
when using LTO.
Change-Id: Ifc44e2c0467f8bd1f537b5a69c501ba51053d3d9
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Allocate storage for the BERT reserved memory in cbmem, and add it in
response to a romstage hook. Add a Kconfig option for adjusting the
size reserved. This is different from the Stoney Ridge implementation
where it was intentionally oversized to ease MTRR use and to keep TSEG
aligned.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4759154d394a8f5b35c0ef0a15994bbef25492e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38694
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tioga Pass platform use GPIO pin of GPP_B20 for POST complete,
BIOS needs to configure this pin for BMC to poll,
so it knows when to start to access other components.
Tested=Read GPIO status (GPIOAA7) in OpenBMC, the value is 0,
the command and result are shown as below,
root@bmc-oob:~# cat /tmp/gpionames/FM_BIOS_POST_CMPLT_N/value
0
root@bmc-oob:~#
Change-Id: I134f80153461c5acd872587038a2207586b658dd
Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
EFS2 allows EC RO to enable PD for special cases. When doing so, it sets
NO_BOOT flag to avoid booting the OS. AP needs to get NO_BOOT flag from
Cr50 and enforce that.
This patch makes verstage get a boot mode and a mirrored hash stored
in kernel secdata from Cr50.
This patch also makes romstage write an expected EC hash (a.k.a. Hexp) to
Cr50 (if there is an update).
BUG=b:147298634, chromium:1045217, b:148259137
BRANCH=none
TEST=Verify software sync succeeds on Puff.
Signed-off-by: dnojiri <dnojiri@chromium.org>
Change-Id: I1f387b6e920205b9cc4c8536561f2a279c36413d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
tlcl_cr50_get_boot_mode gets the boot mode from Cr50. The boot mode
tells coreboot/depthcharge whether booting the kernel is allowed or
not.
BUG=b:147298634, chromium:1045217, b:148259137
BRANCH=none
TEST=Verify software sync succeeds on Puff.
Signed-off-by: dnojiri <dnojiri@chromium.org>
Change-Id: Iadae848c4bf315f2131ff6aebcb35938307b5db4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40388
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The eMMC/SD interface is not present in all Intel platforms so this
change removes the default enable for the storage controller and
instead enables it in the specific SoCs that do provide it.
Currently this includes all platforms except Tigerlake.
Change-Id: I8b6cab41dbd5080f4a7801f01279f47e80ceaefd
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Type C connector class driver in kernel (v5.4) expects the Type C ACPI
device under ChromeEC ACPI device scope. Currently the Type C ACPI
device is populated under ChromeEC device's parent. This leads to
incorrect casting of Type C's parent device and hence a crash. Move the
Type C device under ChromeEC ACPI device.
BUG=b:153518804
TEST=Build and boot the mainboard. Ensure that the USBC ACPI device is
populated under ChromeEC ACPI device.
Scope (\_SB.PCI0.LPCB.EC0.CREC)
{
Device (USBC)
{
Name (_HID, "GOOG0014") // _HID: Hardware ID
...
}
}
Change-Id: I628489bc420d7a3db4ad3cb93d085d568c6de507
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Implement the MboxBiosCmdSmmInfo function to inform the PSP of the SoC's
SMM configuration. Once the BootDone command is sent, the PSP only
responds to commands where the buffer is in SMM memory.
Set aside a region for the core-to-PSP command buffer and the
PSP-to-core mailbox. Also add an SMM flag, which the PSP expects to read
as non-zero during an SMI.
Add calls to soc functions for the soc to populate the trigger info and
register info (v2 only).
Add functions to set up the structures needed for the SmmInfo function
in Picasso support. Issue a SW SMI, and add a new handler to call the
new PSP function.
BUG=b:153677737
Change-Id: I10088a53e786db788740e4b388650641339dae75
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Commit 991ee05 ("mb/gigabyte/ga-h61m-s2pv: rename to ga-h61m-series")
renamed the mainboard folder from `ga-h61m-s2pv` to `ga-h61m-series`,
but the MAINTAINERS file was not updated accordingly. Correct that.
Change-Id: I8119e29912e04ab57bebb96f37a4147afbb4d56e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Since SeaBIOS rel-1.7.5 CONFIG_THREAD_OPTIONROMS is not present in its
config. The threaded hardware initialization during optionrom execution
is now controlled with a CBFS file. Add appropriate integer to CBFS when
threaded hardware initialization is selected in coreboot's Kconfig.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I9b5a532b609c6addf31ccdb6be03ff2e937ad326
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Legacy mode is supposed to help with IDE controller drivers that don't
know Intel's "native" IDE interface. We extend the `sata_mode` NVRAM
variable to provide the following choices:
* 0 "AHCI" - AHCI interface
* 1 "Compatible" - Intel's "native" interface
* 2 "Legacy" - Legacy interface
Change-Id: I0e7a4befa02772f620602fa2a92c3583895d4d1c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
CLKRUN_EN bit available for mobile is reserved on desktop SKUs.
PSEUDO_CLKRUN_EN bit available for desktop is reserved for mobile SKUs.
Configure these bits accordign to SKU.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I5295eb2bec27c77f800cc2ade9093e97ede47789
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
It's relatively slow to boot. It takes 1.5s to get to the payload.
In timestamps there are entries related to TPM, which are somewhat
weird given that the TPM is not enabled on this device (buggy).
TESTED: boot X60, with CONFIG_H8_FN_KEY_AS_VBOOT_RECOVERY_SW=y you
can force the recovery bootpath.
Change-Id: Ia9666194e98b7d23b97eaff08e6177684e35eca7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We decided to add a third RAM_CODE pin to the Trogdor family for devices
after rev1. This patch adds support to read it. Since the newly used pin
was previously unconnected (not pulled down) on rev1, this will change
the RAM_CODE result for previous versions (and actually make it
undetermined until we enable tri-state). But since we're not actually
using RAM_CODE for anything yet, and since those are development
revisions that will eventually be discontinued, this should be fine.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9b52982f17646a305b1a3e2c7d37606a7c38d0c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
TCSS TBT PCIE root ports scope type was mistakenly set to PCI_ENDPOINT.
Fix the scope type to be PCI_SUB.
BUG=b:141609884
TEST=Booted to kernel and verified no TBT PCIE root ports scope
type mismatch error in kernel log.
Change-Id: I844e7e9583992be496223fb51f24c5aa24fc7d21
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
To provide sane defaults for most of the user base, this patch switches
on the USE_BLOBS option by default. Since it only changes the default,
this behaviour can still be easily disabled.
With this abuild doesn't have to select USE_BLOBS any more, so what
abuild tests becomes the coreboot default again.
Change-Id: Ia0632b9ae7a1f212a8640b3faec2695d17d238c5
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Boots to Linux.
Works:
- CPU (Core i3-2120 tested)
- Memory (one 1GB 1Rx8 PC3-10600E module tested)
- Slots 4, 6, 7
To fix/improve:
- SuperIO hardware monitor setup for PECI and fan control
- SuperIO ASL in DSDT (e.g. UART Devices)
- PEG PCIe lanes (should show x8 max width instead of x16 on 0:1.0 for Slot 7)
Untested:
- IPMI where BMC is fully implemented (X9SC[LM](+)-F variants)
- GbE on X9SCL+-F (where there are two 82574L instead of one)
- Slot 5 (x4 on 0:06.0) (only applicable to X9SCM variants)
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Change-Id: I985db89d67de21bbafbdc34d7044496434a6eb17
Depends-On: I5b7599746195cfa996a48320404a8dbe6820483a, I1206746332c9939a78b67e7b48d3098bdef8a2ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38346
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Provide the option to disable XHCI LFPS power management.
If the option is set in the devicetree, the bits[7:4] in
XHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated
from default 9 to 0.
BUG=b:146768983
BRANCH=None
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Marx Wang <marx.wang@intel.com>
Change-Id: Ic603e3b919d8b443c6ede8bb5e46e2de07fcb856
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In order to support mainboards that do not store DRAM part number in
the traditional way i.e. within the CBFS SPD for soldered memory, this
change provides a runtime callback to allow mainboards to provide DRAM
part number from a custom location e.g. external EEPROM on dedede.
For other boards it should be a NOP since the weak implementation of
mainboard_get_dram_part_num does nothing.
BUG=b:152019429
Change-Id: I7ba635f5504ba288308d7d7a4935f405f289aa8d
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
* Add FMAP for measured boot only, with a single RO partition.
* Add FMAP for measured boot only, with a single RO partition
but where the ME has been shrunken.
Tested on X220 using VBOOT+measured boot:
* Used patched IFD and ME, boots into OS
Change-Id: I04c1add13198444638c669deec1e05159b1a09c9
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peter Lemenkov <lemenkov@gmail.com>
Add a function to dump ME Host Firmware Status registers.
In tigerlake, Manufacturing mode is “No” if below conditions are satisfied, indicating
end of manufacturing. Otherwise, manufacturing mode is "Yes".
1. Intel fuses are programmed (Indicated by HFSTS6[30] bit set)
2. The SPI flash descriptor region is locked. (Indicated by HFSTS1[4] cleared)
BUG=None
BRANCH=None
TEST=Build and boot tglrvp.
Change-Id: I831a51f9f482425bd3b97ef1d2404b1d06844d07
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
According to Intel Document #616599,
1) SPD byte offset #5 for Tiger Lake should be "0x21" (16 rows, 10
columns)
2) SPD byte offset #13 for Tiger Lake should be "0x01" (1 channel
x16)
This change fixes those two values in the existing SPD files for
Volteer, and zero's byte 9 (bytes 8-11 should be zero'd out in a
generic SPD).
BUG=b:152827558
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
Volteer to kernel.
Change-Id: Ice6a32a2b3827cf99d8e109731ffd9efabf68de1
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Fix GPIO_PCH_WP (GPP_B11) to associate GPP_PCH_WP with community
zero instead of community 1.
BUG=b:152876091
TEST="emerge-volteer coreboot chromeos-bootimage", flash, boot to
and log into Volteer kernel, execute "wp enable" in H1 console,
execute "crossystem" at kernel prompt and verify that "wpsw_cur"
shows as being "1", Execute "wp disable" in H1 console, execute
"crossystem" at kernel prompt and verify "wpsw_cur" is 0.
Change-Id: I082154efd72459ec54999ed7c7bb7420a38f7b6e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The current flash layout requires changes to the descriptor area to
create the 9MB BIOS region.
Add fmd files that allow switching to coreboot by only replacing the
BIOS region.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: I2b003018e245693934202505d7e3891c2f545e6c
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
The QEMU XHCI controller does not support byte/word reads from the
capability register and it expects dword reads only.
In order to make this work move the access of the capability
register fields to use macros instead of a packed struct bitfield.
This issue was filed upstream:
https://bugs.launchpad.net/qemu/+bug/1693050
The original fix attempt in 2012 was not effective:
6ee021d410
With this change the controller is detected properly by the libpayload
USB drivers.
Change-Id: I048ed14921a4c9c0620c10b315b42476b6e5c512
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Kernel relies on the USB MUX interrupt to configure USB devices that
are connected on the Type-C ports for TGL. Adding in the Q1C Interrupt
so the Kernel can properly receive and configure USB devices
BUG=b:152902608
TEST=buld_packages for volteer and verified that Proto 1 and Proto 2
are now seeing extcon events
Change-Id: Ie3a2f829a295f090a03e72e12f19ecc5bb724952
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Prashant Malani <pmalani@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some of the revision 4 FADT fields were already updated to ACPI
spec revision 6, but not all of them. In addition the advertised
FADT revision was 3.
Implement all fields as defined in version 6 and bump the advertised
FADT revision to 6.
Also set all used access_size fields and x_gpe0_blk to sane values
as Windows 10 verifies those fields starting with FADT revision 5.
Fixes: https://ticket.coreboot.org/issues/109
Tested on Windows 10.
Change-Id: Ic649040025cd09ed3e490a521439ca4e681afbbf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
When EC_GOOGLE_CHROMEEC_SKUID is selected provide an
implementation of smbios_mainboard_manufacturer() so the code
doesn't need to be duplicated in the mainboards.
BUG=b:153767369
Change-Id: Ib65fe373a79d606cffcba71882b0db61be5a18c3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Family 17h redefines the PSP command and status, and therefore the
steps required to send commands via the mailbox. Convert the existing
version into a v1 and add a v2. New Kconfig options allow the soc to
choose v1 vs. v2.
The v2 PSP begins responding to the mailbox command when the full
bit range is written. Define the new mailbox as a union of a u32
and a structure.
Additional PSP details may be found in the NDA publication (#55758)
AMD Platform Security Processor BIOS Architecture Design Guide for
AMD Family 17h Processors
Change the existing two soc functions that return pointers to void
pointers.
BUG=b:153677737
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4d358fdae07da471640856f57568059e9487f6a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enable audio for Jasper Lake RVP board. It has 2 Audio codec chips
connected on I2C0: DA7219 and MAX98373
1. Enable Kconfig to enable I2C drivers for both chips.
2. Make necessary devicetree changes to enable FSP UPDs and ACPI entry
for I2C0.
3. Enable audio related GPIO configurations.
BUG=None
BRANCH=None
TEST=Checked that dmic and speaker are functional on Jasper Lake RVP
Change-Id: Ibf76eb36c478bd33cbc0c86099236452b397fcc5
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39695
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change disables MrcSafeConfig option during MRC training.
MrcSafeConfig was enabled as part of the early testing.
Now with FSP 2527, there is no need to set this config anymore.
BUG=b:150357377
BRANCH=master
TEST=build and boot ripto/volteer
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I4e4069d83754aaf1e4885d6912ab2a6d506c5269
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40106
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current pin-ctrl kernel v5.4 driver expects the firmware to publish
single GPIO ACPI device. Until kernel pin-ctrl driver implementation is
updated to consume community based GPIO ACPI device, update the current
ACPI code to comply with pin-ctrl driver requirement.
BUG=b:150154277
TEST=Verify intel pin-ctrl driver can successfully load in OS
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: Ifcc92adaee550182ab405541ea85019f31bb8658
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
`.read_resources` and `.set_resources` are the only two device
operations that are considered mandatory. Other function pointers
can be left NULL. Having dedicated no-op implementations for the
two mandatory fields should stop the leaking of no-op pointers to
other fields.
Change-Id: I6469a7568dc24317c95e238749d878e798b0a362
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40207
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It turns out the linker's error message already includes the line
number of the dead_code() invocation. If we don't include the line
number in the identifier for our undefined reference, we don't need
individual identifiers at all and can work with a single, global
declaration.
Change-Id: Ib63868ce3114c3f839867a3bfb1b03bdb6facf16
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set IgdDvmt50PreAlloc to zero if InternalGfx is disabled. It's 'correct'
to do it like this, otherwise the FSP would always allocate memory for
the IGD even if it is disabled. In addition the FSP enables the graphics
panel power even if no IGD is present which leads to a crashing FSP.
Thus, if no IGD is present we switch off the panel via UPDs.
Refer to this issue on IntelFSP for details:
https://github.com/IntelFsp/FSP/issues/49
Tested on:
* CFL platform with IGD
* CFL platform without IGD
Change-Id: I6f9e0f9855224614471d8ed23bf2a9786386ddca
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
In some cases Hatch variants are not laptop form-factors such
as Puff. Ensure that the base configuration does not assume
the form factor and allow variants to elect their intended
use-case.
Note that the issue is that early ec sync needs to be
disabled for EFS2 to function correctly, see commit 6daa8c3ba5
from the FIXME line. The relationship is that desktops do not
have a battery.
BUG=b:152951181
BRANCH=none
TEST=none
Change-Id: I15dc9efa51e9d61297868df287879dfb62909e33
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40252
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Apply initial DPTF parameters for nightfury from internal thermal team. Will update after further thermal/performance tuning.
BUG=b:149226871
BRANCH=firmware-hatch-12672.B
TEST=built and verified FAN worked by DPTF active policy
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: I712bdd8edc999ef7ee33f4adf21893be12e86bec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Adds definitions that allow to use the common GPIO driver to configure
the Lewisburg PCH pads. Using the GPIO configuration from common/gpio,
unlike the FSP-style definitions from Intel RefCode [1] definitions,
is more understandable and makes the motherboards code much cleaner.
In addition, we can use utilities, such as inteltool, to analyze the
configuration of proprietary firmware to add support for new server
motherboards with Skylake-SP processors.
The pin layout in this patch corresponds to the pinctrl driver in the
Linux kernel v4.14 for the Lewisburg PCH GPIO controller [2].
[1] https://designintools.intel.com/product_p/stlgrn45.htm
[2] drivers/pinctrl/intel/pinctrl-lewisburg.c
These changes are in accordance with the documentation:
[*] page 39, Intel(R) C620 Series Chipset Platform Controller Hub
(PCH) Datasheet, May 2019. Document Number: 336067-007US.
Change-Id: Idde32fdd53f1966e3ba6b7f5598ae8f51488d5a5
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39425
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According TCG PC Client Platform Firmware Profile Specification Revision
1.04 Chapter 8.1 the TPM device object should have the _CID and _HID
values set to MSFT0101 for TPM2.
FreeBSD also detects TPM2 device using MSFT0101 _HID and _CID only.
TEST=boot FreeBSD 12.1 on PC Engines apu2 and check in dmesg that TPM2.0
is detected
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I45123f272038e664b834cabd9d8525baca0eb583
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39699
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use defined structures to assemble IVRS and IVHD entries. Additionally
assemble IVHD type 11h which supersedes IVHD type 10h. In order to
utilize all IOMMU features firmware should also expose IVHD type 11h.
The new type is already supported and parsed since Xen 1.13. IVHD
type 10h should still be present for backwards compatibility.
TEST=boot PC Engines apu2 and disassemble IVRS using newest IASL,
boot Xen 1.13 or newer with debug enabled and see IVRS IVHD 11h parsed
in xl dmesg
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I9a2c24b67adfa8ebd718caeb5eec88687dcbcc9d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In order to support mainboards that do not store DRAM part number in
the traditional way i.e. within the CBFS SPD for soldered memory, this
change provides a runtime callback to allow mainboards to provide DRAM
part number from a custom location e.g. external EEPROM on volteer /
dedede.
For other boards it should be a NOP since the weak implementation of
mainboard_get_dram_part_num does nothing.
BUG=b:152019429
Change-Id: If940a76d36a7645a7441ba418aa7aec9af9f6319
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
It is use to skip GT specific programming in ICL, TGL and JSL.
In following patches use of SKIP_GRAPHICS_ENABLING is removed.
b6a523927d (soc/intel/jasperlake: Remove DDI A lane programming)
e5565c45cb (soc/intel/{icelake, tigerlake}: Remove DDI A lane programming)
TEST=checked iclrvp, jslrvp and tglrvp compilation.
Change-Id: Ie337fd727d72118c43aa869da1446ea4fceadc5b
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
For newer Intel graphics (>=11), the DDI port max lanes default to 4.
And kernel driver no longer relies on coreboot to provide information
via DDI_BUF_CTL_A (for DDI port A) register programming. Hence removing
this code.
BUG=b:150788968
BRANCH=None
TEST=checked jslrvp compilation and boot.
Change-Id: I4c171ec6a57d6fc53bee88420bfb3c0fbc5dc057
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40038
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move more Kconfig declarations to drivers/intel/fsp2_0/ and document
them properly. This way, we don't have to repeat dependencies and have
the prompts in a common place. We can also easily hide the prompt for
the header path in case the FSP repository is used.
SP platforms were skipped as their Kconfig is too weird but they
shouldn't hold other platforms back.
Change-Id: Iba5af49bcd15427e9eb9b111e6c4cc9bcb7adcae
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
We can make our lifes much easier by removing its dependency on
`ADD_FSP_BINARIES`. Instead, we imply the latter if the repository
is to be used. We can also hide a lot of unnecessary prompts in
this case.
Also, remove default overrides and selects for the two that are
now unnecessary.
Change-Id: I8538f2e966adc9da0fbea2250c954d86e42dfeb3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39882
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When dead_code() is used in inline functions in a header file, the
generated function names (based on the line number) may collide with
a dead_code() in the code file. Now that we are hit by such a case,
we need a quick solution: Add a tag argument for all invocations in
header files.
Change-Id: I0c548ce998cf8e28ae9f76b5c0ea5630b4e91ae2
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Stumpy is a Chromebox without a built-in display, and now
that default_brightness_levels.asl is no longer required
for all boards in a platform, drop it and the default panel
definition.
Test: build/boot stumpy
Change-Id: Iaf475f3529dd19330ea46532e9ffd20b44893f7e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add minimal MP init. No SMM, no turbo, not c/p states.
TEST=boot linux kernel, observe CPUs are online, schedule tasks
and perform useful work. Tested on Cedar Island CRB with only 1
socket populated
Change-Id: I0af374ab3956009e9208917d911d29eb21db6069
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Our realloc() works (somewhat suboptimally) by free()ing the existing
allocation and then reallocating it wherever it fits. If there was free
space before the old location, this means the new allocation may be
before the old one, and if the free space block is smaller than the old
allocation it may overlap. Thus, we should be moving memmove() instead
of memcpy() to move the block over.
This is not a problem in practice since all our existing memcpy()s are
simple iterate and copy front to back implementations which are safe for
overlaps when the destination is in front of the source. but it's still
the more correct thing to do (in case we ever change our memcpy()s to do
something more advanced or whatever).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I35f77a94b7a72c01364ee7eecb5c3ff5ecde57f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Disable SoC serial output by default, since no production devices
have this exposed, but leave it as a user option so it can be selected
as needed (eg, for use with a Google debug servo).
Same change as made for google/cyan in CB:39872
Change-Id: Id6b2c28658aca03d8c5042d719a0f6f504c29288
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The jack detect GPIOs are initialized as dual edge-triggered GPIs,
and Linux doesn't care if they are set to ActiveLow, ActiveHigh, or
ActiveBoth -- a single interrupt is detected on jack insertion or
removal.
The Windows drivers on the other hand, will not function unless the
codec and LPE ACPI interrupts entries are set as in the Intel
Cherry Trail Tianocore platform reference code.
So adjust the ACPI interrupt triggers to make Windows happy, since
Linux doesn't care either way.
Test: boot Linux (GalliumOS 3.1) and Windows 10 on google/edgar,
observe functional audio output for both built-in speakers and
headphones.
Change-Id: Ic1dd8ece610d761791c060ece2d0aa51addf97ad
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/24989
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adjust CID to allow for Realtek's Windows drivers to attach
without breaking functionality under Linux.
Both Linux and Windows use ACPI HID/CID matching for driver attachment.
Since the Realtek 5650 isn't used in standard Windows laptops, the
'10EC5650' HID/CID isn't contained in the Windows drivers' lookup file
(.inf), but a catch-all 'INTCCFFD' entry does exist, so concatenate
that to the existing CID to allow the drivers to attach.
Test: build/boot google/edgar, verify working audio under
both Windows 10 (with Realtek drivers 10.0.10586.4393) and Linux
(GalliumOS 3.1 / kernel 4.16.18, Manjaro 18.1 / kernel 5.1.x)
Change-Id: Idca5cc86ba1f5ef3978cfba291a0c06e56ef5958
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40003
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Braswell boards don't work well with the eMMC and SD controller
in ACPI in payloads other than depthcharge - SeaBIOS requires
an onerous workaround (manually determining the PCI BAR0 address
for each eMMC and SD controller, then adding adding etc/sdcard
entries to the CBFS), and Tianocore can't see the devices at all.
To make the common use-case work better, switch to PCI mode.
Test: build/boot cyan variants with SeaBIOS and Tianocore
payloads, verify eMMC and SD card visible and bootable to
both payloads and OSes.
Change-Id: I71947603e22a37fe2c8ef4eaac8a3aa0d0ed1cec
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40002
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Simply cyan variants by converting to overridetree format.
A few differences were ignored as there appears to be no
reason behind them:
- cyan had PCIe RP2 enabled, but nothing is attached to it
- kefka had the SPI 1 device disabled
- reks, relm, and ultima had HSUART 1 disabled
- edgar had I2C1 UPD disabled
Test: build/boot cyan and edgar variants, verify everything
still works
Change-Id: I9928cc59adcfda4661ddfdfa95f53a7820053b4a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39964
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The VR config values used in the variants' devicetrees is
identical to the domain defaults in vr_config.c, with the
exception of the icc_max value, which is calculated dynamically
based on SKU, and again matches the default values for
each domain and each varaint.
Test: add a print function to dump the VR config values for each
domain from the UPDs after setting, verify same output before/after.
Change-Id: I4307f6e19ae6f99d4f5e475b181fd66c5b92f28c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39982
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In preparation for conversion to overridetree format, clean up
the variant devicetrees in order to minimize the differences
across glados variants. This entails:
- minor reformatting and reordering of devicetree entries
- addition of setting default values on boards which skipped them
- disabling unused I2C2 on boards which left it enabled
- ensuring TCC offset set for all SKL-Y boards
- setting VR mailbox command 1 for caroline
- skipping init for UART2 on cave and glados
- dropping unused PCIe RP5 for sentry
Change-Id: I628b20a69fab187e67901c9eb98c0e2ddcb76b0d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39981
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are boards that do not need a specific domain_vr_config because
the defaults provided by the soc code are sufficient. Currently, this
means that these boards can't benefit from lower power states (PSI 3
and 4) because the settings default to being disabled since at the time
the defaults have been defined (2015) there were bugs in FSP in this
regard.
Set the default values of psiXenable to 1 for boards that do not have a
domain_vr_config setting in their devicetree, just like Cannon Lake
does.
Boards that have a domain_vr_config and set their specific settings are
not affected at all. Currently, there are only three boards that have
no domain_vr_config:
- supermicro/x11-lga1151-series
These boards have a MPS MP2955 which we can assume support for PS3
(the MP2965 and MP2935 support it, too).
S-series CPUs with a 1151 socket do not have C9/C10 but only C8 and
since only C10 makes use of PS4, those CPUs won't ever request PS4.
That means we do not need to disable it explicitly for these boards.
- 51nb/x210:
Needs testing and/or VR datasheet check for PS3/PS4 support
Change-Id: I5b5fd9fb3b9b89e80c47f15d706e2dd62dcc0748
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39980
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the variants' devicetrees are almost identical, convert to
using an overridetree setup for simplicity.
As part of the cleanup, drop unused PCIe RP5 for buddy as well.
Test: build all auron variants, compare generated static.c to ensure
resulting generated contents unchanged (although layout will)
Change-Id: I290e7243335a64afdcfc629db7b8ce18f5aa993c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add hook to generate ACPI methods in SSDT for screen backlight control.
To make use of this, individual boards will need to
include default_brightness_levels.asl in their dsdt, as
well as add 'register "gfx" = "GMA_STATIC_DISPLAYS(0)"' to
their devicetree.
Change-Id: I0adccc6c8bee71d3c1b7840518308c8dc8ea2d81
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add hook to generate ACPI methods in SSDT for screen backlight control.
To make use of this, individual boards will need to
include default_brightness_levels.asl in their dsdt, as
well as add 'register "gfx" = "GMA_STATIC_DISPLAYS(0)"' to
their devicetree.
Change-Id: I0b7fc45bda3aaf89306bedb579fb1e9f8ce07926
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Simplify generation of GMA SSDT, using updated naming convention.
If acpi_fill_ssdt is being invoked, then we know the IGD device is
present and enabled, so we can skip those checks. And the SSDT
generator now checks that the gfx struct is populated, so we can
skip that too.
Change-Id: Ideddfc3d327c4421faffb6583e347cd2b094e155
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Simplify generation of GMA SSDT, using updated naming convention.
If acpi_fill_ssdt is being invoked, then we know the IGD device is
present and enabled, so we can skip those checks. And the SSDT
generator now checks that the gfx struct is populated, so we can
skip that too.
Change-Id: I68848516fab2058d4aa96ac0342c883fd1df2d6d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Simplify generation of GMA SSDT, using updated naming convention.
If acpi_fill_ssdt is being invoked, then we know the IGD device is
present and enabled, so we can skip those checks. And the SSDT
generator now checks that the gfx struct is populated, so we can
skip that too.
Change-Id: Iacce01ab7d6c220779e84c2b695fbb597b493586
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Simplify generation of GMA SSDT, using updated naming convention.
If acpi_fill_ssdt is being invoked, then we know the IGD device is
present and enabled, so we can skip those checks. And the SSDT
generator now checks that the gfx struct is populated, so we can
skip that too.
Change-Id: I1b6d57c091441aa7431061b1f16135d54cc97b47
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Simplify generation of GMA SSDT, using updated naming convention.
If acpi_fill_ssdt is being invoked, then we know the IGD device is
present and enabled, so we can skip those checks. And the SSDT
generator now checks that the gfx struct is populated, so we can
skip that too.
Change-Id: If34ebe0edc46674244c9d5afc7ed165c2ad685ba
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Simplify generation of GMA SSDT, using updated naming convention.
If acpi_fill_ssdt is being invoked, then we know the IGD device is
present and enabled, so we can skip those checks. And the SSDT
generator now checks that the gfx struct is populated, so we can
skip that too.
Change-Id: Icd9caf622dd4c46b13589ebb772138b25888752f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39948
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
NDID/DID entries are no longer used by the GMA SSDT generator, so
drop them. SSDT generation will be simplified in a subsequent commit.
Remove direct setting of gnvs->ndid in qemu-q35 board since build
will otherwise break.
Change-Id: Ifbf08f43291c1fff7ccbc85272dc97334207983b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39954
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add framework to generate ACPI methods in SSDT for
screen backlight control. Adjust params for gtt_ methods
to match prototypes in i915.h and avoid conflicts.
To make use of this, individual boards will need to
include default_brightness_levels.asl in their dsdt, as
well as add 'register "gfx" = "GMA_STATIC_DISPLAYS(0)"' to
their devicetree.
Change-Id: If93b7690ef36b5d19ca43957e8a1bef91ec5821d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change reorganizes memory initialization code for LPDDR4x on
TGL to allow sharing of code when adding support for other memory
types. In follow-up changes, support for DDR4 will be added.
1. It adds configuration for memory topology which is currently only
MEMORY_DOWN, however DDR4 requires more topologies to be
supported.
2. spd_info structure is organized to allow mixed topologies as well.
3. DQ/DQS maps are organized to reflect hardware configuration.
TEST=Verified that volteer still boots and memory initialization is
successful.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib625f2ab30a6e1362a310d9abb3f2051f85c3013
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This commit creates a malefor variant for Volteer. The initial settings
override the baseboard was copied from variant ripto. Fine tune GPIO
and memory DQ based on malefor schematics.
BUG=b:150653745
BRANCH=volteer
TEST=emerge-volteer coreboot
Signed-off-by: William Wei <wenxu.wei@bitland.corp-partner.google.com>
Change-Id: Idbeebb13e537287686344740211143df35b7863a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39857
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:35077 pulled TPM measurement code into the bootblock, with the catch
that we'll only cache PCR extensions and not actually write them to the
TPM until it gets initialized in a later stage. The goal of this was to
keep the heavy TPM driver code out of the size-constrained bootblock.
Unfortunately, a small mistake in the tspi_tpm_is_setup() function
prevents the compiler from eliminating references to the TPM driver
code in the bootblock on platforms with CONFIG_VBOOT and
CONFIG_SEPARATE_VERSTAGE. In those cases vboot_logic_executed() is known
at compile-time to be 0, but that still makes the final expression
`return 0 || tpm_is_setup;`. We know that tpm_is_setup can never be set
to 1 in the bootblock, but the compiler doesn't.
This patch rewrites the logic slightly to achieve the same effect in a
way that the compiler can follow (because we only really need to check
tpm_is_setup in the stage that actually runs the vboot code).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Idc25acf1e6c02d929639e83d529cc14af80e0870
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39993
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Switch to using Jasper Lake SoC code from soc/intel/jasperlake and stop
referring from soc/intel/tigerlake.
Addtionally mainboard changes are done to support build.
BUG=b:150217037
TEST=Build and boot waddledoo. Build jasperlake_rvp and volteer board.
Change-Id: I39f117bd66cb610a305bcdb8ea65332fd0ff4814
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
cmos.default used to be loaded only when cmos is needed to be reset,
but conditional loading of CBFS files may change the calculated PCRs
if measurement is hooked on each loading.
In order to resolve this, loadings should be made less conditional,
(if a file might be used, it should be loaded and measured) but the
use of loaded data remains conditional.
Change-Id: If6ea0d1cbaa7d96f7dea7e77b7548ca2b30efe9e
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39906
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds the path to chrome EC headers to the depthcharge
build. Depthcharge currently includes a manually maintained copy of
the EC headers which are perpetually out of sync with the real
interface definitions. By adding the include path, we can build
depthcharge with the actual EC interface definitions and eliminate the
manual maintenance of copies of EC headers. Once the include path is
in place, we can remove the copies of the EC headers from depthcharge.
BUG=b:152373049
Change-Id: I1ce0ad9dc99ea52f177d4fb034fd23efd95a7864
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Certain PCIe endpoints cause an exception inside AmdInitMid when PCIe
ClockPM is enabled in AGESA PCIe initialization structures. Disable it
to allow platform to boot with such devices. coreboot driver enables
the ClockPM correctly on such devices anyway.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I7fb13f915861c26cf773960abb12a3a1c0211cdc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Include types.h in src/soc/intel/common/block/include/intelblocks/cse.h
to use type bool.
Without this, there can be a build error like below,
src/soc/intel/common/block/include/intelblocks/cse.h:208:1:
error: unknown type name 'bool'; did you mean '_Bool'?
bool cse_is_hfs1_com_soft_temp_disable(void);
^~~~
_Bool
src/soc/intel/common/block/include/intelblocks/cse.h:214:1:
error: unknown type name 'bool'; did you mean '_Bool'?
bool cse_is_hfs3_fw_sku_custom(void);
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: I92ee533bca7dc255f7a341b2a68bbc09900996a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Including gma.asl at the platform level (vs the board level)
means that even desktop boards need to include the default
brightness levels, which makes no sense. To begin to clean this up,
include gma.asl in default_brightness_levels.asl (as well as
the handful of board-specific brightness files) and remove it
from the various platforms.
A follow-on commit will remove default_brightness_levels.asl
from all boards which lack an internal display.
Change-Id: I8063deeef4ab6d6ab34ed9b0be5b1d541d6e9b6b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39878
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allow Chrome OS to be enabled for this QEMU target. By default
this does not change anything unless it is selected in the build
configuration, but it makes it possible.
Native VGA init is not forced when Chrome OS is enabled because the
drm-bochs driver does not work with chrome (even the latest upstream
kernel driver with drm atomic support) but it does work with virtio.
The coreboot graphics init needs to match what is selected with qemu
(with -vga std or -vga virtio) which in turn will determine which
kernel driver is used.
A second FMAP is added with both RW-A and RW-B regions which is
required by chromeos.
Recovery mode can be entered by supplying a custom fw_cfg option
when launching qemu: -fw_cfg name=opt/cros/recovery,string=1
Change-Id: I24b4532ea961e68558663292c99d121f0a30ce3b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This enables the mainboard to use a TPM if it is selected in the
configuration. By default this does nothing, but it allows the
TPM to be enabled and used with the CONFIG_USER_TPM2 Kconfig option.
Using a TPM with QEMU requires either a physical TPM backend or
the swtpm package with a socket:
-chardev socket,id=swtpm,path=/tmp/swtpm/socket
-tpmdev emulator,id=tpm0,chardev=swtpm
-device tpm-tis,tpmdev=tpm0
Change-Id: I0d79a5a0f590c57998ababb660b52d9e3ed2d484
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
QEMU does not have a separate northbridge chip, so the mainboard
needs to handle the ACPI name and paths so that devices can get
generated into the SSDT properly. This fixes the PIRQ and TPM
table generation.
This issue can be seen in the coreboot output:
ACPI_PIRQ_GEN: Missing LPCB ACPI path
Change-Id: Ifc7d4359eea38ac0b55d655e39191ae7f8655fe4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Ensure that the low memory is properly reserved so it does not get
marked as normal RAM and get wiped or reused by firmware or the kernel.
This ensures that the low RSDP is always available for the kernel.
This is only noticed if something wipes the RSDP before the kernel
boots, which happens if you use the depthcharge payload and boot in
developer mode.
Change-Id: I7295018416229bc957ecbf26f77623a57965557e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
When the TPM is enabled in QEMU the fw_cfg interface will return
~200KiB of ACPI tables, so this needs to be increased from the default
in order to be able to boot.
This is seen when using a TPM with qemu as it will hang when
processing the fw_cfg tables.
qemu-system-x86_64 \
-machine q35 -enable-kvm -vga virtio -serial stdio \
-drive 'id=hd,file=disk.bin' -bios coreboot.rom \
-chardev 'socket,id=swtpm,path=/tmp/swtpm/swtpm-sock' \
-tpmdev 'emulator,id=tpm0,chardev=swtpm' \
-device 'tpm-tis,tpmdev=tpm0'
Change-Id: I21980aace8e86e636f5ae7b55148f4c31404edba
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The maximum ACPI table size is currently hardcoded to 144 KiB.
When using QEMU with TPM enabled there is ~200 KiB of ACPI tables
returned by the fw_cfg interface, so in order to allow this to be
overridden by a mainboard move it to Kconfig.
This is seen when using a TPM with qemu as it will hang when
processing the fw_cfg tables.
qemu-system-x86_64 \
-machine q35 -enable-kvm -vga virtio -serial stdio \
-drive 'id=hd,file=disk.bin' -bios coreboot.rom \
-chardev 'socket,id=swtpm,path=/tmp/swtpm/swtpm-sock' \
-tpmdev 'emulator,id=tpm0,chardev=swtpm' \
-device 'tpm-tis,tpmdev=tpm0'
Change-Id: Ib5baa8fe12cb9027a340875f1ccf5fef6f9460bd
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
After measured boot is decoupled from verified boot in CB:35077,
vboot_platform_is_resuming() is never vboot-specific, thus it is
renamed to platform_is_resuming() and declared in bootmode.h.
Change-Id: I29b5b88af0576c34c10cfbd99659a5cdc0c75842
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
mrc.bin, on platforms where it is present, is code executed on CPU, so
it should be considered a part of CRTM.
cbfs_locate_file_in_region() is hooked to measurement here too, since
mrc.bin is loaded with it, and CBFS_TYPE_MRC (the type of mrc.bin) is
measured to TPM_CRTM_PCR rather than TPM_RUNTIME_DATA_PCR.
TODO: I have heard that SMM is too resource-limited to link with vboot
library, so currently tspi_measure_cbfs_hook() is masked in SMM.
Please correct me if I am wrong.
Change-Id: Ib4c3cf47b919864056baf725001ca8a4aaafa110
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Since the variants' devicetrees are almost identical, convert to
using an overridetree setup for simplicity.
Test: build all slippy variants, compare generated static.c to ensure
resulting generated contents unchanged (although layout will)
Change-Id: If237fad38a1bccfb8e51edfae3ecb75d05ade240
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update the Lenovo Ivy Bridge documentation that no issues could be
observed on W530.
Tested on Lenovo W530 with stripped ME and found no issues:
commit 93b0c7cfc6
* USB
* Bluetooth
* Wifi
* Wifi-kill switch
* libgfxinit
* SATA
* mSATA
* Audio
* SD-card
* Ethernet
* Keyboard
* Fn-Keys
* Display brightness
* ACPI S3 resume
* CPU temperature reporting
* Stress test stable (intel_pstate no_turbo due to W530 overheating bug)
* Youtube videos
* stress -c 8 -m 1 -t 3600
Change-Id: I46d23d41cc6ade5e641a6ddb3f357a6036002edc
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39603
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, those who want to use measured boot implemented within
vboot should enable verified boot first, along with sections such
as GBB and RW slots defined with manually written fmd files, even
if they do not actually want to verify anything.
As discussed in CB:34977, measured boot should be decoupled from
verified boot and make them two fully independent options. Crypto
routines necessary for measurement could be reused, and TPM and CRTM
init should be done somewhere other than vboot_logic_executed() if
verified boot is not enabled.
In this revision, only TCPA log is initialized during bootblock.
Before TPM gets set up, digests are not measured into tpm immediately,
but cached in TCPA log, and measured into determined PCRs right after
TPM is up.
This change allows those who do not want to use the verified boot
scheme implemented by vboot as well as its requirement of a more
complex partition scheme designed for chromeos to make use of the
measured boot functionality implemented within vboot library to
measure the boot process.
TODO: Measure MRC Cache somewhere, as MRC Cache has never resided in
CBFS any more, so it cannot be covered by tspi_measure_cbfs_hook().
Change-Id: I1fb376b4a8b98baffaee4d574937797bba1f8aee
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Add an enable reset delay to avoid messages like this in the
kernel:
i2c_hid i2c-WCOM50C1:00: failed to change power setting.
This gets rid of all the warnings except one on reboot/shutdown.
That last case likely isn't fixed because the sleep command is
being sent directly from i2c_hid_shutdown(), so no ACPI routines
get to run and provide the delay. Since the machine is going down
for shutdown/reboot anyway, fixing that last case is a lower
priority.
BUG=b:145094539
TEST=Run on kohaku, switch to guest mode and log out, no errors
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: I8fadf497dd09e5b95b1d74443fb0543d3555dbb8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
For quite a bit now we are extending the FSP_USE_REPO option to be
available for all Intel SoCs. This results in a list being not only
hard to maintain but also prone to errors.
To change that behaviour this commit introduces the
HAVE_INTEL_FSP_REPO config option for SoCs that are supported from within
3rdparty/fsp.
If a SoC selects HAVE_INTEL_FSP_REPO the config option FSP_USE_REPO is
selected by default, but can be still deselected by the user in menuconfig.
Change-Id: I68ae373ce591f06073064aa75aac32ceca8fa1cc
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37582
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Coalescing is not needed, as root port #1 is enabled. Also, update the
comments to look more like the other two variants. Note that the Intel
H61 PCH only has six root ports, so devices 1c.6 and 1c.7 do not exist.
Change-Id: I3f4bf99ceec6c77f6e1eabea9b712245afee7d34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39742
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates the align attribute of memranges to be represented
as log2 of the required alignment. This makes it consistent with how
alignment is stored in struct resource as well.
Additionally, since memranges only allow power of 2 alignments, this
change allows getting rid of checks at runtime and hence failure cases
for non-power of 2 alignments.
This change also updates the type of align to be unsigned char.
BUG=b:149186922
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ie4d3868cdff55b2c7908b9b3ccd5f30a5288e62f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This initial devicetree attempts to correctly configure the status of
each PCI device. Not all required drivers are instantiated, nor are
all of the SoC options fully selected yet.
PCIe root ports are enabled and clocks are assigned.
USB ports are assigned.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I911ec08b0db3647d131113a138fb74a55612fd62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
In order to create a working baseline all ports are being set to have
retimers. Setting the TcssAuxOri UPD to 0 in order for the SoC to not
misconfigure the ports. Volteer will need some additional changes after
this is implemented to account for ports that do not have a retimer.
This setting is in the process of being documented in the TGL EDS and we
can update once it is fully understood what this setting is changing on
the SOC side.
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on Volteer,
Connecting Type-c display should work regardless of Type-c cable
orientation.
Change-Id: I29eb0513299126ad8d1ee11ded2c771f28ad13f3
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39460
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP UPD TcssAuxOri is used for setting the IOM_TYPEC_SW_CONFIGURATION_3.
Configure TcssAuxOri to retimer enabled on the port 2 Type-C port.
This setting informs the SoC that a retimer is taking care of SBU
orientation therefore it does not need to do any flipping.
The IOM_TYPEC_SW_CONFIGURATION_3 is a bitfield that controls the aux
orientation settings for the Type-C ports. The TGL EDS describes this
setting and what each bit represents.
Reference section 3.6.5 in TGL EDS #575681
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on volteer,
Connecting Type-C display should work regardless of Type-C cable
orientation.
Change-Id: Iae356113cbdc72983f800060b1ebebe3c66b9daf
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39459
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's helpful to see the sibling field, even when it's NULL, when
debugging the static.c output from a devictree.cb file. Ensure the
NULL fields are emitted for fullness.
Change-Id: Ib6d5b8164769a6512e762d5a525c7df1f429c866
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Glados boards do not have an exposed serial port outside
of the servo interface. Set board Kconfig so that a default
built image with Tianocore payload is bootable and doesn't
hang due to trying to send data over a non-existant serial port.
Test: build/boot google/chell with board defaults
Change-Id: Ifad6f805e66438e2c436d9fa235d9be2ecf69179
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Further backport the backlight-PWM handling from Skylake. Beside
configuring the PWM frequency in Hz, we also use the PCH's logic
for the brightness setting via BLM_PCH_OVERRIDE_ENABLE. Linux
would toggle it anyway and that might confuse our ASL code.
We assume that the 183Hz value that was set before for Slippy
variants was overridden by Linux with the 200Hz VBT value, like
it was for the Broadwell Chromebooks. So we set 200Hz for them
in the devicetrees. The calculated value for the T440p of 220Hz
seems sane and also matches the VBT.
Change-Id: I17dfe1a3610d5e2918c617cf5d10896692fdccb3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Adjust the defaults for Graphics Initialization so
that the "best" option for a board is selected by default.
Net effect is to select RUN_FSP_GOP over VGA_ROM_RUN
in cases where the platform supports GOP init and the
mainboard has a VBT file included.
Test: run 'make menuconfig' and check default Display
Init option for google/cyan, observe RUN_FSP_GOP is default.
Change-Id: I2184dbdd943d035d1682b3ae7bd8d005221434b1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Cyan has no VGA BIOS available (at least not publicly), so
remove related options. Disable SoC serial output by default,
since no production devices have this exposed, but leave it
as a user option so it can be selected as needed (eg,
for use with a Google debug servo).
Change-Id: Ic079a39ca5ad0ac653b52248244b94d4bfbd08a4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39872
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Chrome-EC/PD images for all glados variants need to be built
from the board-specific branch, not master. Including the default
board names serves no purpose and requires users to deselect
the "use built-in EC firmware" in order for the board to build.
Test: build google/chell with defaults
Change-Id: Ic10f11337b85035068cdc4fe8147413e6b7f57ac
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add missing port definition for the mSATA/WWAN mPCIe port,
set OC pin for internal ports to OC_SKIP, fix port
descrption for mPCIe/WLAN port, remove USB3 definition for
right type-A port as it is USB2 only.
Test: insert WiFi module into WWAN port, observe BT portion
detected and functional.
Change-Id: Ie39b99eeb0f605ff07d57c32189fb1f4183713e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Create the sushi variant of the hatch reference
board by copying the template files to a new directory named
for the variant.
(Auto-Generated by create_coreboot_variant.sh version 3.0.0).
BUG=None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_SUSHI
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: Ie900d09ff55e695527eafe68a5a75cd4a0b6d340
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add struct i915_gpu_controller_info for boards to supply info needed
to generate ACPI backlight control SSDT. Hook into soc/common framework
by implementing intel_igd_get_controller_info().
Change-Id: I70e280e54d78e69a335f9a382261193c593ce430
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add framework to hook up the generic src/drivers/intel/gma ACPI
backlight control for platforms using SOC_INTEL_COMMON_BLOCK_GRAPHICS.
Add a weak function to get the struct i915_gpu_controller_info needed
to generate the SSDT, defaulting to NULL, which SoC's will override.
Each SoC will need to override intel_igd_get_controller_info, and
individual boards will need to populate the struct in order for
the backlight control methods to be added to the SSDT.
Change-Id: I993770fdcd0a28cee756df2bd6a795498f175952
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32549
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a copy patch from Tiger Lake SoC code.
The only changes done on top of copy is changing below configs:
1. SOC_INTEL_TIGERLAKE -> SOC_INTEL_TIGERLAKE_COPY
2. SOC_INTEL_JASPERLAKE -> SOC_INTEL_JASPERLAKE_COPY
3. SOC_INTEL_TIGERLAKE_BASE -> SOC_INTEL_TIGERLAKE_BASE_COPY
We started with initial assumption that JSL and TGL can co-exist.
But now we see the SoC code in Tiger Lake is relying on too many
compile-time directives to make two SoCs co-exist. Some of the
differences are listed below:
-> Kconfig: Multiple Kconfig options using
if SOC_INTEL_{TIGERLAKE/JASPERLAKE}
-> GPIO: GPIO communities have their own differences.
This requires conditional checks in gpio.asl, gpio.c, gpio*.h,
pmc.h and gpio.asl
-> PCI IRQs: Set up differently for JSL and TGL
-> PCIe: Number of Root ports differ.
-> eMMC/SD: Only supported on JSL.
-> USB: Number of USB port are different for JSL and TGL.
-> Memory configuration parameters are different for JSL and TGL.
-> FSP parameters for JSL and TGL are different.
The split of JSL and TGL SoC code is planned as below:
1. Copy Tiger Lake SoC code as is, and change SoC Kconfig
to avoid conflicts with current mainboard builds.
2. Clean up TGL code out of copy patch done in step 1.
Make it JSL only code. The SoC config still kept as
SOC_INTEL_JASPERLAKE_COPY.
3. Change JSL SOC Kconfig from SOC_INTEL_JASPERLAKE_COPY to
SOC_INTEL_JASPERLAKE, dedede and jasperlake_rvp boards can
bind to SoC code from soc/intel/jasperlake. This step establishes
Jasper Lake as a separate SoC.
4. Clean up current JSL code from TGL code. This step establishes
Tiger Lake as a separate SoC.
BUG=b:150217037
Change-Id: I9c33f478a2f8ed5e2d8e7815821d13044d35d388
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
These header files are just placeholders. Currently FSP does not
look into any real platform-specific UPD fields anyway, so having
padding instead of real thing makes no difference.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: Id123f4386124b2ceb7776ab719a9970c9c23a0e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
This adds barebones support.
What works:
* Linux kernel boots fine
* SIRQ and PCH interupts work fine (only in IOAPIC mode)
* PCH devices are usable
What doesn't:
* MP init is not there yet, only 1 CPU is up
* SMM is not supported
* GPIO is not available
* All IIO and extended bus numbers enumeration is not yet available
* Warm reset flow is untested
* MRC cache save/load
TEST=boots into Linux
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I7c987badc3c53f16ad178369c7e0906d6596e465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39713
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tioga Pass comes with AST2500 BMC which offers SuperIO functionality.
However we currently do not configure/enable SuperIO chip. As a result
system boots pretty silently on cold boot. Then FSP configures SuperIO
and resets the system so on next boot serial console does work. This
makes debugging difficult because pre-FSP output is invisible.
This patch enables bootblock to properly configure desired BMC SuperIO
port so early serial output is visible.
TEST=do a cold boot on OCP Tioga Pass, observe bootblock output starting
from bootblock.
Change-Id: Iff8e6a862858d733f529bb9b8c65e22e5ec6b521
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
1.Select CHROMEOS_EC related Kconfig for variant board with
external EC support.
2.Select proper CHROMEOS Kconfigs which are required for all
variants.
3.Disable Intel EC region in case of external EC.
BUG=None
BRANCH=None
TEST=Compilation is successful for both Jasper Lake RVP variants.
Change-Id: I290b3748777e18476651101de71df9080dd3105c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39584
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some commands, like ZQCS and ZQCL, use the same macro. This is because
they differ in things outside of the IOSAV_SP_CMD_CTRL registers. Also,
correct a comment that does not concur with the actual command in use.
With BUILD_TIMELESS=1, the binary of ASUS P8Z77-V LX2 remains identical.
Change-Id: Id2ff4c85f9d9db7c892b764472423cbf2e6db422
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The code for Sandy Bridge is a subset of the code for Ivy Bridge. Adapt
the Ivy Bridge code so that it also supports Sandy Bridge, and use it.
Tested on Asus P8Z77-V LX2, still boots with i7-2600 and i5-3330.
Change-Id: I7b78ec605aff976b9a5cdbb364a69df4b4947c6e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39737
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Unfortunately this was noticed only after commit 0e1380683f
merged, credit to Sam McNally for spotting it. Previously
the legacy path replaced the space with a null byte and so
the expected string here is precisely "ethernet_mac" and
not "ethernet_mac ".
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: I603fad4efd6d6c539137dd714329bcea1877abdd
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39856
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The format for VPD has changed s.t. the first NIC should
always have a zero concat to the end.
Adjust all the respective boards to shift back by one and
adjust drivers/net friends to remove the 'special casing'
of idx == 0.
Background:
https://chromeos.google.com/partner/dlm/docs/factory/vpd.html#field-ethernet_macn
V.2: Fixup a code comment typo while we are here.
V.3: Vary special casing semantics for idx==0 => default mac addr is set.
V.4: Rework to still support the legacy path.
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: Idf83cc621a9333186dabb668b22c4b78e211930a
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Orginally fetch_mac_string_vpd() has been special cased around
a device_index of 0/1 that causes a number of edge cases and
complexity when attempting to refactor to deal with the revised
VPD format. The following change prepares the ground work by
splitting up the functional into logical workers where we can
deal with each edge case in a more bounded way.
The background here is that the format for VPD has changed s.t. the
first NIC should always have a zero concat to the end. The details
of that can be found here:
https://chromeos.google.com/partner/dlm/docs/factory/vpd.html#field-ethernet_macn
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: Idc886d9b0b3037c91f40b742437e4e50711b5f00
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In order to use early serial output we need to enable P2SB BAR0, because
that allows PCR access to PCH registers.
TEST=tested on OCP Tioga Pass
Change-Id: I476f90b2df67b8045582f0b72dd680dea5a9a275
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Refactor the code and split it into Xeon common and CPU-specific code.
Move most Skylake-SP code into skx/ and keep common code in the current
folder.
This is a preparation for future work that will enable next
generation server CPU.
TEST=Tested on OCP Tioga Pass. There does not seem to be degradation
of stability as far as I could tell.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I448e6cfd6a85efb83d132ad26565557fe55a265a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39601
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sometimes coreboot needs to compile external code (e.g.
vboot_reference) using its own set of system header files.
When these headers don't line up with C Standard Library,
it causes problems.
Create stdio.h and stdarg.h header files. Relocate snprintf
into stdio.h and vsnprintf into stdarg.h from string.h.
Chain include these header files from string.h, since coreboot
doesn't care so much about the legacy POSIX location of these
functions.
Also move va_* definitions from vtxprintf.h into stdarg.h where
they belong (in POSIX). Just use our own definitions regardless
of GCC or LLVM.
Add string.h header to a few C files which should have had it
in the first place.
BUG=b:124141368
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I7223cb96e745e11c82d4012c6671a51ced3297c2
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Currently, there are a lot of uploads in the board status repository,
where the logs say, that the coreboot image or payload were built from a
dirty source tree. Add a check to reject such uploads.
Change-Id: I920e26a10f74e1f3b9b4e5f8c9284c59692a519b
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Define a chip option to explicitly soft reset all enabled GPIOs to
default state.
TEST=boot FreeBSD 11.2 on PC Engines apu1, change GPIO configuration
using nctgpio module and check whether GPIOs are reset after reboot
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iae4205574800138402cbc95f4948167265a80d15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
It does not change once a frequency has been set, so store it somewhere.
Since this changes the saved data definition, update MRC_CACHE_VERSION.
As SNB will eventually use the same code, only IVB is being refactored.
Change-Id: I25b7c394abab173241fffdf57ac5c929daad8257
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
There is no need to call get_FRQ a dozen times with the same parameters.
As SNB will eventually use the same code, only IVB is being refactored.
Tested on Asus P8Z77-V LX2, still boots with i7-2600 and i5-3330.
Change-Id: Idd7c119b2aa291e6396e12fb29effaf3ec73108a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39723
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Instead of adding more versions of the `*pch.asl`, unify the existing
ones and allow to override the register locations via Kconfig. The
current defaults should work for Skylake and some newer platforms.
TEST=Booted ThinkPad X201s, backlight control still works.
Change-Id: I0b21d9a0288f0f8d6cb0a4776909bffdae7576f5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
The 2nd COM port's base address defaults to 0x2f8. Current software
for this system expects the port at 0x3e8.
Configure COMB to use 0x3e8 instead of 0x2f8.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: Ibb462bad5f0594e0b5c8dea6e02cd42d58d999ab
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The concerned GPIO is configured as an open drain at the Embedded
Controller side without an external pull-up. This causes leakage in the
PP3300_A rail. So configure the GPIO to have a weak internal pull-up at
the SoC side.
BUG=b:151680590
TEST=Build the mainboard. Ensure that there are no leakages in the
PP3300_A rail.
Change-Id: I5553cf40adb92edc0fecab5c875ec8d72063ba7b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
AMD's Family 17h SOCs have the same vendor and device IDs for
their graphics blocks, but need different video BIOSes. The
only difference is the revision number.
Add a Kconfig option that allows us to add the revision number
of the graphics device to the PCI option rom saved in CBFS.
Because searching CBFS takes a non-trivial amount of time,
only enable the option if it's needed. If it's not used, or
if nothing matches, the check will fall through and search for
an option rom with no version.
BUG=b:145817712
TEST=With surrounding patches, loads dali vbios
Change-Id: Icb610a2abe7fcd0f4dc3716382b9853551240a7a
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2013181
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add memory initialization parameters for Jasper Lake RVP boards
Jasper Lake RVP supports two variants, one with memory LPDDR4
and another with DDR4
Based on board id, mainboard will pass correct memory parameters
to the fsp.
BUG=None
BRANCH=None
TEST=Check compilation for Jasper Lake RVP and check memory training passes.
Change-Id: Idc92363a2148990df16c2068c7986013d015f604
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39195
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here.
Additionally add processor scope patching for P-State SSDT created by
AGESA, becasue AGESA creates the tables with processors in \_PR scope.
TEST=boot Debian Linux on PC Engines apu2, check dmesg that there are
no errors, decompile ACPI tables with acpica to check whether the
processor scope is correct and if IASL does not complain on wrong
checksum, run FWTS
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I35f112e9f9f15f06ddb83b4192f082f9e51a969c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39698
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A bigger than zero value of bmc_boot_timeout must be set
for KCS ipmi_get_bmc_self_test_result() to run, otherwise
the self test result will be error and won't write SMBIOS
type 38 table. Here we set 60 seconds as the maximal self
test timeout.
Tested=Check if the BMC IPMI response data and SMBIOS type
38 on OCP Tioga Pass are correct or not.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: I3678973736a675ed22b5bc9da20a2ca947220f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The timing tables for Sandy Bridge are a subset of Ivy Bridge's tables.
Move the latter to a common place, and use it for both generations.
Tested on Asus P8Z77-V LX2 with an i7-2600 and an i5-3330, both work.
Change-Id: Id14227febf4eebb8a2b4d2d4f37759d0f42648c6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39735
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PC Engines apu2 had many problems with PCIe cards detection. The cards
were inconsistently detected when booted from G3, S5 or after a reboot.
AGESA can reset PCIe slots using GPIO via callback. Use it to reset the
slots that support using GPIO as reset signal.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I8ff7db6ff85cce45b84729be905e6c895a24f6f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The `link_frequency_270_mhz` setting was originally used by the native
graphics init code for Sandy/Ivy Bridge, which is long gone.
The value of this information (which board had it set) is questionable.
The only board that had an LVDS panel and set it to 0 was the ThinkPad
L520, where native graphics init was never reported to work. Also, the
native graphics init only used it for calculations, but never confi-
gured the hardware to use a specific frequency. A look into the docu-
mentation also doesn't reveal any straps that could be used to confi-
gure it.
Change-Id: Ieceaa13e4529096a8ba9036479fd84969faebd14
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39763
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PWM-granularity chicken bit in the Wildcat Point and Lynx Point
PCHs has actually the opposite meaning of the one for Sunrise Point
and later. When the bit is set, we get a divider of 16, when it's
unset 128. Flip the bit!
Change-Id: I1dbde1915d8b269c11643a1636565a560eb07334
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
_DCS, _DGS and _DSS are required by specification. However,
we never implemented them properly, and no OS driver com-
plained yet. So we stub them out and keep the traditional
behavior in case an OS driver checks for their existence.
The old implementations also only returned static values as
there never was any write to their GNVS variables. The TRAP()
that was called in one place is actually implemented by some
ThinkPad's SMI handler as docking event. However, as the call
precedes these SMI handlers in coreboot history, it's most
likely an accident.
Change-Id: Ib0b9fcdd58df254d3b2290900e3bc206a7abd92d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
According to the latest Tigerlake Platform FSP Integration Guide, the
minimum amount of stack needed for FSP-M is 256KiB. Change
DCACHE_BSP_STACK_SIZE to reflect that (plus 1KB previously determined
empirically). JSL requires 192KiB.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ic9be6446c4db7f62479deab06ebeba2c7326e681
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Native raminit asserts that the DIMMs haven't been replaced before
reusing the saved training data. However, it does not check if the CPU
is still the same, so it can end up happily reusing data from an Ivy
Bridge CPU onto a Sandy Bridge CPU, which runs the raminit_ivy.c code
path. This can make the CPU run in unsupported configurations, which may
result in an unstable system, or a failure to boot.
To prevent that, ensure that the stored CPUID matches the CPUID of the
installed CPU. If they differ, print a message and do not use the saved
data. As it does not pose a problem for a regular boot, but precludes
resuming from S3, use different loglevels depending on the bootpath.
Tested on Asus P8Z77-V LX2 with an i7-2600 and an i5-3330, works well.
Change-Id: Ib0691f1f849b567579f6afa845c9460e14f8fa27
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Instead of storing an int with a single bit of information taken from
the CPUID, we might as well store the actual CPUID. And since we are
changing the definition of the saved data, bump the version number.
Tested on Asus P8Z77-V LX2, still boots fine.
Change-Id: I6ac435fb83900a52890f823e7614055061299e23
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39720
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When changing any of the structures that are cached in non-volatile
storage, it is necessary to bump MRC_CACHE_VERSION so that the old
information is not misinterpreted.
Change-Id: Idefbc38b3a8198b1b5909e775b3c289db689fc0c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39756
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Header files are supposed to not make allocations from .bss. Builds
fail if said file is included multiple times. To prevent this from
happening, move the definitions to a C file.
Also, rename raminit_patterns to raminit_tables. This is because more
tables that are not patterns will be added here in subsequent changes.
Tested on Asus P8Z77-V LX2, still boots fine.
Change-Id: If8e3a285ecdc4df9e978ae156be915ced6e1750b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39754
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here for Intel CPUs only.
Tested on:
* X11SSH (Kabylake)
* CFL Platform
* Asus P8Z77-V LX2 and Windows 10
FWTS does not return FAIL anymore on ACPI tests
Tested-by: Angel Pons <th3fanbus@gmail.com>
Change-Id: Ib101ed718f90f9056d2ecbc31b13b749ed1fc438
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
According to BKDGs HTC temperature limit field indicates the threshold
where HTC becomes active. HTC active state means that processor is
limiting its power consumption and maximum P-State. Using this threshold
as _CRT is incorrect, since HTC active is designed to prevent
overheating, not causing immediate shutdown.
Change the behavior of temperature limit to act as a passive cooling
threshold. Make the passive cooling threshold a reference value for
critical and hot temperature with 5 degrees step.
TEST=boot FreeBSD on PC Engines apu2 and check the thermal zone
temperature using sysctl
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Ife64c3aab76f8e125493ecc8183a6e87fb012e3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This is required for PD notifications on the cros_ec driver.
BUG=b:150649744
TEST=Boot volteer with this patch and verify that PD notifier events are
being generated.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Change-Id: I2e72320b025a3dfa7412181586cb142a4503eda5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently cbfstool cherry-picks a few files from vboot and hopes these
files will work standalone without any dependencies. This is pretty
brittle (for example, CL:2084062 will break it), and could be improved
by building the whole vboot library and then linking against it.
Therefore, this patch creates a new target $(VBOOT_HOSTLIB) and includes
it as a dependency for cbfstool and ifittool.
To prevent building the vboot lib twice (one for cbfstool and the other
for futility) when building coreboot tools together, add the variable
'VBOOT_BUILD' in Makefile to define a shared build path among different
tools so that vboot files don't need to be recompiled.
Also ignore *.o.d and *.a for vboot library.
BRANCH=none
BUG=none
TEST=make -C util/cbfstool
TEST=make -C util/futility
TEST=Run 'make tools' and make sure common files such as 2sha1.c are
compiled only once
TEST=emerge-nami coreboot-utils
Change-Id: Ifc826896d895f53d69ea559a88f75672c2ec3146
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
It does not make sense to disable an optimization that was not enabled
before, especially if that optimization only applies to Ivy Bridge.
Tested, still boots and can suspend correctly with:
- Asus P8Z77-V LX2 with i5-3330 and Windows 10
- Gigabyte GA-H61MA-D3V with i5-2400 and Arch Linux
Change-Id: I9f3eb545585824bbdf51e33f0592e7daa1c425af
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch replaces hard-coded PCI IDs with macros from pci_ids.h and
adds the related IDs to it.
The resulting binary doesn't differ from the one without this patch.
Used documents:
- Intel 322170
Change-Id: I3326f142d483f5008fb2ac878f30c1a3a72f500f
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner
Check that there are actually USB-PD ports for which to
add data to SSDT, before actually generating SSDT data.
This prevents an empty scope from being generated on
devices without any USB-PD ports, which was breaking
parsing/decompilation on some older platforms (eg,
Braswell).
Test: build/boot google/edgar, verify SSDT table able to
be parsed via iasl after dumping.
Change-Id: Ia213e5815e9160e9b36b2501eeccb6385abef47e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39665
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating devicetree to enable ELAN touchpad and ELAN touchscreen on nightfury
BUG=none
BRANCH=firmware-hatch-12672.B
TEST=built and verified touchpad and touchscreen worked
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: Ieba6558ce3897ce2f95f51ed667465d84b4ab189
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
PMC core driver in OS provides debug hooks to developers and end users
to quickly figure out why their platform is not entering a deeper idle
state such as S0ix. This patch adds INT33A1, a required ACPI device,
to support that PMC core driver in tigerlake platform.
BUG=b:146236297
BRANCH=none
TEST="Build and flash volteer and verify it boots to kernel.
Checked for valid files under /sys/kernel/debug/pmc_core."
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Ib7e583dc2943461a41d2a7ebde1f16a58a118975
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39587
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Split common flags that are not specific to the C language out of
$CFLAGS_GCC into $FLAGS_GCC. This way, we can test for C specific
flags, too, without adding them to $ADAFLAGS_*. Currently this is
done for `-Wno-address-of-packed-member` which only applies to C.
Change-Id: Ib793c62656efb07b6e5b3385f1ed1c96a40efd1d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39633
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The DMI link consists of four lanes, grouped in two bundles. Therefore,
some DMI registers may be organized as "per-lane" or "per-bundle". This
can be seen in the DMI initialization sequence as series of equidistant
offsets being programmed with the same value. Make this more obvious by
factoring out the register groups using loops.
With BUILD_TIMELESS=1, the binary of ASUS P8Z77-V LX2 remains identical.
Change-Id: Iebf40b2a5b37ed9060a6660840ea6cdff7eb3fc3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This is a µATX mainboard with a LGA1150 socket and four DDR3 DIMM slots.
Working:
- All four DIMM slots
- Serial port to emit spam
- Some USB ports
- Integrated graphics (libgfxinit)
- HDMI and DVI
- Intel GbE
- All PCIe ports
- Both PCI ports behind the ASM1083 PCI bridge
- At least one SATA port
- RAM initialization with MRC binary
- Flashing with flashrom
- S3 suspend/resume
- Rear audio output
- VBT
- SeaBIOS to boot Arch Linux
Not working:
- PS/2 keyboard (detected as mouse)
Untested:
- The other audio jacks
- S/PDIF
- VGA
- EHCI debug
- Front USB headers
- Non-Linux OSes
- TPM header
- Parallel port
Change-Id: I10a16dfc56f2aa88648c8aaaba4feab40c491504
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36770
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Reformat some lines of code
- Move MCHBAR registers and documentation into a separate file
- Add a few missing macros
- Rename some registers
- Rewrite several comments
- Use C-style comments for consistency
- Rewrite some hex constants
- Use HOST_BRIDGE instead of PCI_DEV(0, 0, 0)
With BUILD_TIMELESS=1, this commit does not change the result of:
- Asus P8Z77-V LX2 with native raminit.
- Asus P8Z77-M PRO with MRC raminit.
Change-Id: I6e113e48afd685ca63cfcb11ff9fcf9df6e41e46
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39599
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If they were removed instead, it would be too easy to end up adding them
back again. They are kept in a comment so that they can be tracked.
Also, explain why these two entries have been commented out.
Change-Id: I8225944b5e3d1e022af169dda33e0344d4c3bccd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The existing Sunrise Point ids are assigned to the wrong implementation,
which would never work for these chipsets. Assign them to the right
dumping implementation, which works for both Sunrise Point PCH-H and
PCH-LP.
This also adds some missing device ids from doc#332691-003EN and
doc#334659-005.
Change-Id: Id102ef3809d675dc9a915d2cb3062e093487fa27
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
FSP needs to know to allow the root ports for USB4/TBT to be enabled
This patch may need additional checks for each board as it might not
be the right thing to turn them all on for every Tiger Lake board.
BUG=b:141609883
BRANCH=NONE
TEST=Built image and verified that the root ports were visible with lspci
Change-Id: I3f020e20fa8e9fd1ac69d883f4dc1fcbb330a3bf
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Adds GMM into the baseboard of Octopus
For GLK, PCI device 3 is GMM according to
Document#: 569262(Glk EDS Vol-1 rev2-7)
Related to Gerrit review 39579
BUG=b:151115705
BRANCH=None
TEST=Flashed final image on Chromebook
Change-Id: I75b4a835c18c5eeb542b7f7b89deea45a31e47bd
Signed-off-by: Franklin He <franklinh@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enables Gaussian Mixture Model (GMM) if the pci device is enabled in the
devicetree for Gemini Lake
This ports commit 03ddd190fd
BUG=b:151115705
BRANCH=none
TEST=Flashed to Chromebook, PCI device enabled in cbmem, userspace app
that uses device still works
Change-Id: I72b1dd78705894f0462c7fbe89b76551950c2392
Signed-off-by: Franklin He <franklinh@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I4c110f60b764c97fab2a29f6f04680196f156da5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I426518e8e18de1c8efcfb7ecb0835df3e257dca1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39608
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I09cc279b1f75952bb397de2c3f2b299255163685
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
The current implementation doesn't allow custom values for the LPC IO
decodes and IO enables.
Add the lpc_ioe and lpc_iod values. If they are not zero, they will be
used instead of the current handling for COMA and COMB.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: Iad7bb0e44739e8d656a542c79af7f98a4e9bde69
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38748
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I18e513cefc373b1cd70d31d1159928cc948a8476
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I57fc98788bb47df16d6aedd0f0701e9991801743
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I89b10076e0f4a4b3acd59160fb7abe349b228321
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39611
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On newer kernels (> 4.9 LTS), the GPIO ACPI device's interrupt
resource causes an interrupt storm which prevents the CPU
from properly idling, significantly increasing power consumption.
This was fixed for soc/broadwell (which also supports lynxpoint-lp)
by removing the interrupt resource, so apply the same fix here.
Original fix: https://chromium-review.googlesource.com/203645
Test: build/boot google/wolf, verify CPU0 idles correctly and
power consumption drop via powertop in kernels 4.16.18 and 5.x.
Change-Id: Ic4963f2f0225b5f44a7604b0107911640345c855
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
* Change power sequence to make it closer to ov8856 sensor
data sheet version 2
* Handle different PWREN GPIO pins for up3 and up4
* Add link frequencies definitions to sensor side
* Clean up format
BUG=None
BRANCH=None
TEST=Build and boot TGLRVP U or Y. Start camera app and able to
capture images.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Ic11a36f1f82fe425c1a5796847ce020007064403
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39529
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Method RAOW is assuming that the first argument is a Field object
and writing to it expecting the register to get updated. However,
the callers are passing in the value of the Field object instead.
This eventually is resulting the IMGCLK not getting enable/disabled on the
platform.
Fix this by sending the exact address of the register to be updated.
Also MCCT was setting the clock frequency in both case i.e, Clock Enable
and Disable. Split the MCCT method in two, MCON and MCOF to fix the sequencing
like below
MCON:
Set frequency
Enable clock
MCOF:
Disable clock
Also, make use of MCON and MCOF methods for camera clock control in tglrvp.
This is to avoid the buildbot marking the patch unstable.
BUG=None
BRANCH=None
TEST=Build and Boot waddledoo board and verified that IMGCLKOUT for
world facing camera is enabled/disabled and able to capture images.
Build and Boot Tiger Lake RVP board and verified that IMGCLKOUT for
world facing camera is enabled/disabled and able to capture images.
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: I8b886255d5f38819502ae1f4af0851b5a0922b22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39498
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set FSP params PchSirqEnable/PchSirqMode based on board
setting of serirq_mode. Matches implementation on Skylake.
This is a no-change for existing boards since the default
remains SERIRQ_QUIET mode.
Tested on system76 galp3-c, out-of-tree WHL-U board
Change-Id: I9ad4f5a6c7391fc6e813ec1306c708f449a69f59
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Nathaniel L Desimone <nathaniel.l.desimone@intel.com>
These platforms use the standard fixed function power button
and do not need a second power button device declared or the
kernel will end up with two devices reporting the same event.
Same change was applied to all google mainboards in
CB:27272 which contains more detail.
Change-Id: I17c85e43493530d04f4fa13f33bec6d027cb3147
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39577
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds memranges_steal() which allows the user
to steal memory from the list of available ranges by providing a set
of constraints (limit, size, alignment, tag). It tries to find the
first big enough range that can satisfy the constraints, creates a
hole as per the request and returns base of the stolen memory.
BUG=b:149186922
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ibe9cfae18fc6101ab2e7e27233e45324c8117708
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change enables memranges library to support addresses with
different alignments. Before this change, memranges library supported
aligning addresses to 4KiB only. Though this works for most cases, it
might not be the right alignment for every use case. Example: There
are some resource allocator changes coming up that require a different
alignment when handling the range list.
This change adds a align parameter to struct memranges that determines
the alignment of all range lists in that memrange. In order to
continue supporting current users of memranges, default alignment is
maintained as 4KiB.
BUG=b:149186922
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I1da0743ff89da734c9a0972e3c56d9f512b3d1e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
So far printing the GPIO groups chose the community definition. As the
list of supported platforms grows the massive switch case gets repetetive
and hinders the readers view.
It also reduces the ability to reuse the code in a potential libinteltool.
To takle these issues the detection logic was split into its own function.
Change-Id: I215c1b7d6ec164b8afd9489ebd54b63d3df50cb9
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38631
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
So far all group and community definitions live in one big c file.
This 2500 line file slowly grows to a size, where readability is lost.
Also the definitions are not reusable in a potential libinteltool.
This commit moved the Denverton definitions into its own header.
Change-Id: I6ce672c24059b9f3a4a984766184066f14df3013
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38630
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christoph Pomaska <github@slrie.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
So far all group and community definitions live in one big c file.
This 2500 line file slowly grows to a size, where readability is lost.
Also the definitions are not reusable in a potential libinteltool.
This commit moves the Lewisburg definitions into its own header.
Change-Id: I7900f1d8b3ca022112874ac2fa7326d538166008
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38629
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christoph Pomaska <github@slrie.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
So far all group and community definitions live in one big c file.
This 2500 line file slowly grows to a size, where readability is lost.
Also the definitions are not reusable in a potential libinteltool.
This commit moves the Sunrise Point and Sunrise Point LP definitions
into its own header.
Change-Id: I06efbee700f1525770365428fb85ef700ac53b80
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38628
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christoph Pomaska <github@slrie.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
So far all group and community definitions live in one big c file.
This 2500 line file slowly grows to a size, where readability is lost.
Also the definitions are not reusable in a potential libinteltool.
This commit moves the Apollo Lake definitions into its own header.
Change-Id: I44b21092f5495f758c1f2151a913c074dfc658f5
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38627
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christoph Pomaska <github@slrie.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
So far all group and community definitions live in one big c file.
This 2500 line file slowly grows to a size, where readability is lost.
Also the definitions are not reusable in a potential libinteltool.
This commit moves the Cannon Lake definitions into its own header.
Change-Id: I5991c3cebba0e05504940ae66fa7bb63bf280ab1
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38626
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christoph Pomaska <github@slrie.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
So far all group and community definitions live in one big c file.
This 2500 line file slowly grows to a size, where readability is lost.
Also the definitions are not reusable in a potential libinteltool.
This commit moves the Ice Lake definitions into its own header.
Change-Id: I5735f12480091a9b6c5e5c103a1ca7b7b1f3f997
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38625
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christoph Pomaska <github@slrie.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BRANCH=none
BUG=b:145946347
TEST=boot to OS with TGL RVP UP3,
then copied ISH firmware to host file system /lib/firmware/intel/tglrvp_ish.bin
check "dmesg |grep ish", it shows:
ish-loader: ISH firmware intel/tglrvp_ish.bin loaded
cros_ec_ishtp: Chrome EC device registered
Those means shim loader in coreboot has loaded ISH firmware, and
firmware is running successfully.
Signed-off-by: Hu, Hebo <hebo.hu@intel.com>
Signed-off-by: li feng <li1.feng@intel.com>
Change-Id: I1ee8050aef6ec0828f16ef2695b5347278caa820
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39481
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The 51nb X210 is a replacement motherboard for Thinkpad X200/X201 systems,
based on a modern Kabylake CPU. It also ships with no firmware protection,
(IFD is fully unlocked, no protected regions are set, no Bootguard),
making it an ideal coreboot target. This port is based on the support for
the Skylake-based Purism Librem 13v3, with the following significant
changes:
* EC firmware is contained within the system SPI flash, and so a blob of
EC firmware must be injected to a defined location during image build.
* GPIO layout is different - this is currently just a raw import of the
GPIO configuration from the vendor firmware
* The system has two DIMMs, so an additional SPD address has been added
* The USB port layout is different
* The EC must be enabled at boot time through SuperIO-style logical device
configuration
* EC register layout is different, necessitating changes in the ACPI tables
* The HDA pins are different
* The genx_dec config is different
All hardware appears to work as expected, although the SD reader is
untested.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Change-Id: If74621e76d703f629b54f1feb1acfc95cc72d183
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Below changes are done:
1. Allow execution of HMRFPO_ENABLE command if CSE meets below
prerequisites:
- Current operation mode(COM) is Normal and Curret working state(CWS)
is Normal.
-(or) COM is Soft Temp Disable and CWS is Normal if ME's
Firmware SKU is Custom.
2. Check response status.
3. Add documentation for send_hmrfpo_enable_msg().
4. Rename padding field of hmrfpo_enable_resp to reserved.
The HMRFPO (Host ME Region Flash Protection Override) mode prevents CSE to
execute SPI I/O cycles to CSE region, and unlocks the CSE region to perform
updates to it. This command is only valid before EOP(End of Post).
For Custom SKU, follow below procedure to place CSE in HMRFPO mode:
1. Ensure CSE boots from BP1. When CSE boots from BP1, it will have
opmode Temp Disable Mode.
2. Send HMRFPO_ENABLE command to CSE. Then, CSE enters HMRFPO mode.
CSE Firmware Custom SKU Image Layout:
= [RO] + [RW + DATA PART] = [BP1] + [BP2 + DATA PART]
Here, BP1 will have reduced functionality of BP2, and the BP1 will be
CSE's RO partition and [BP2 + DATA PART] together will represent
CSE's RW partition. CSE can boot from either BP1(RO) or BP2(RW).
CSE Image Layout in Consumer SKU: BP2 + BP3 + DATA PART
TEST=Verfied on hatch board.
Change-Id: I7c87998fa105947e5ba4638a8e68625e46703448
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
- Reformat some lines of code
- Put names to all MCHBAR registers in a separate file
- Rewrite several comments
- Use C-style comments for consistency
- Rewrite some hex constants
- Use HOST_BRIDGE instead of PCI_DEV(0, 0, 0)
- Align a bunch of things
Tested with BUILD_TIMELESS=1, foxconn/d41s remains unaffected.
Change-Id: I29104b0c24d66c6f49844f99d62ec433bb31bdaf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The code in coreboot is actually for the Arrandale processors, which
are a MCM (Multi-Chip Module) with two different dies:
- Hillel: 32nm Westmere dual-core CPU
- Ironlake: 45nm northbridge with integrated graphics
This has nothing to do with the older, single-die Nehalem processors.
Therefore, replace the references to Nehalem with the correct names.
Change-Id: I8c10a2618c519d2411211b9b8f66d24f0018f908
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38942
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code is for Arrandale CPUs, whose System Agent is Ironlake.
This change simply replaces `nehalem` with `ironlake` and `NEHALEM`
with `IRONLAKE`. The remaining `Nehalem` cases are handled later, as
changing some of them would impact the resulting binary.
Tested with BUILD_TIMELESS=1 without adding the configuration options
into the binary, and packardbell/ms2290 does not change.
Change-Id: I8eb96eeb5e69f49150d47793b33e87b650c64acc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38941
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Reformat some lines of code
- Put names to all used MCHBAR registers
- Move MCHBAR registers into a separate file, for future expansion
- Rewrite several comments
- Use C-style comments for consistency
- Rewrite some hex constants
- Use HOST_BRIDGE instead of PCI_DEV(0, 0, 0)
Tested, it does not change the binary of Asrock B85M Pro4.
Change-Id: I926289304acb834f9b13cd7902801798f8ee478a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38434
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Volteer uses 4 bits (hardware straps) to indicate what memory
configuration the board is populated with (i.e. which SPD file
to use for the populated memory). This allows for only 16
different SPDs for supporting Volteer and all future variants of
Volteer. Currently, each memory chip needs its own SPD file, so we
can only support 16 different memory chip options for Volteer and
all of its variants.
Generic SPD files are just SPD files that have been stripped down
to contain only fields that are important for the memory controller
(strips out items like vendor info, for example). Using generic SPD
files allows for more than 16 different memory options given it's no
longer a 1-to-1 mapping as similar memory modules from different
vendors can share the same generic SPD file.
BUG=b:147857288
TEST="emerge-volteer coreboot chromeos-bootimage", flash ripto and
verify ripto boots to kernel and "cat /proc/meminfo" reports 8GB
of memory.
Change-Id: I17bd4f4a00b4e3bbaf845d6d321962c11569a186
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39423
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Provide settings for configuring the link between HD-Audio controller
and display unit for purposes of HDMI/DP Audio playback.
BUG=b:144708516, b:148385924
TEST=none
Change-Id: I225faac68729b28be65b4d8f1f83769a874f84ff
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39356
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set value for PcieRpL1Substates according to devicetree.
Chip config parameter PcieRpL1Substates uses (UPD value + 1)
because UPD value of 0 for PcieRpL1Substates means disabled for FSP.
In order to ensure that mainboard setting does not disable L1 substates
incorrectly, chip config parameter values are offset by 1 with 0 meaning
use FSP UPD default.
get_l1_substate_control() ensures that the right UPD value is set in
fsp_params.
Chip config parameter values
0: Use FSP UPD default
1: Disable L1 substates
2: Use L1.1
3: Use L1.2 (FSP UPD default)
BUG=none
BRANCH=none
TEST=Boot up and check FSP log for PCIe config for this values
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I66743a29ad182bd49b501ae73b79270a9eb88450
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39412
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable USB ACPI driver. Add ACPI configuration for all the USB ports.
Since one of the USB ports is used for Bluetooth configure the
reset_gpio used by that port.
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I3e7b8f00102c96dcc295601359d3ecfbcd1bea00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
BUG=b:148604250
BRANCH=none
TEST=Build and test booting TGLRVP form NVMe and Optane
Check PCIe lane configuration
Show all the NVMe devices
lspci -d ::0108
Show all the NVMe devices and be really verbose
lspci -vvvd ::0108
Print PCIe lane capabilities and configurations for all the NVMe devices.
lspci -vvvd ::0108 | grep -e x[124]
Print all the PCIe information of the device ae:00.0
lspci -vvvs ae:
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I5fc8fa0897ad006de9ebe20115bf3033e1e1b499
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
This adds case intrusion detection to the SMI handler. At this point one
can add the code to be executed when the INTRUDER signal gets asserted
(iow: when the case is opened).
Examples:
- issue a warning
- trigger an NMI
- call poweroff()
- ...
Tested on X11SSM-F.
Change-Id: Ifad675bb09215ada760efebdcd915958febf5778
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
In case backlight control isn't enabled BCLM is zero.
Return early instead of running into a DivideByZero error.
This happens on devices that don't have backlight control, like
desktops and servers. The proper fix is to not include those
ACPI methods, but that requires a much bigger refactoring.
Change-Id: Ie9bdb00949d6d44fd99321db556d6008d2d12a7f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
PMC logic shuts down the PCH thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold (LTT) in case of Dynamic Thermal shutdown
when S0ix is enabled.
BUG=None
BRANCH=None
TEST=Verified Thermal Device(B0: D18: F0) TSPM offset 0x1c [LTT (8:0)]
value is 0xFE on Drallion.
Change-Id: I146068d8019859be1c27e2a8174dfe7909d42d0a
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Per Mobile Intel ® 945 Express Chipset Family - Specification Update
Document Number: 309220-013 (page 15), the power saving optimization
Erratum is for Mobile Intel ® 945 Express Chipset family.
So rename 'fixup_i945_errata()' to 'fixup_i945gm_errata()' and apply
that function only for I945GM.
Change-Id: I2656021b791061b4c22c0b252656a340de76ae5e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This option is not used on any platform and is not user-visible. It
seems that it has not been used by anyone for a long time (maybe ever).
Let's get rid of it to make future CBFS / program loader development
simpler.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I2fa4d6d6f7c1d7a5ba552177b45e890b70008f36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Intel supplies microcode (at least for MinnowBoard) in Intel Assembly
*.inc format rather than C header. This change allow to pass in
configuration directory with *.inc files rather than list of *.h
files.
Change-Id: I3c716e5ad42e55ab3a3a67de1e9bf10e58855540
Signed-off-by: Bartek Pastudzki <Bartek.Pastudzki@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This eliminates Linux kernel warnings that look like:
pcieport 0000:00:17.0: can't derive routing for PCI INT B
ixgbe 0000:07:00.1: PCI INT B: no GSI - using ISA IRQ 10
Change-Id: I2029e7a8252b9e48c1df457d8da5adce7d1ac21d
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
pcie_port.asl defines an IRQM method that looks up legacy interrupt
swizzling based on incoming interrupt "pin" A-D and root port number.
Unfortunately the 8-bit root port number stored at offset 0x4F in the
config space matches the device number, not the 1-8 scheme used in
the LUT reported to the OS.
Fix the case values to match the hardware.
Change-Id: I103d632a4bc99461f02e05aa0f9a9eb7376770d9
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
SATA Mode Select is bit 16 of the SATA General Configuration
register. This code currently incorrectly pokes at the Port Clock
Disable bits in the Port Mapping Register, and without clock the
affected ports can't link.
Change-Id: I37104f520a869bd45a32cfd271d0b893aec3c8ed
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vanessa Eusebio <vanessa.f.eusebio@intel.com>
Reviewed-by: David Guckian
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Abuild allows us to add config files below `configs/` for each
mainboard. So far, these were built instead of the default config.
However, that allows to hide errors in the default config. Hence,
we should build that too in any case.
Change-Id: I94075dbaa6fabeb75bdbc92e56f237df80c15cef
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39382
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change uses drivers/intel/wifi chip for CNVi device and
adds dynamic SSDT entires for CNVi also export wake gpio for CNVi
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board and check for SSDT entries
for CNVi
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Icdbffa0c29c9e0849a6a99f8592b6f35c0bb3207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39315
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To use Optane memory, we need to set 2x2 PCIe lane mode while we need
to set 1x4 PCIe lane mode for NVMe. The mode can be selected using
the FIT tool at build time.
By enabling hybrid storage mode in FSP, FSP will set 2x2 PCIe lane mode
if Optane memory is detected and the mode is not 2x2 and set 1x4 PCIe
lane mode if Optane memory is not detected and the mode is not 1x4
during boot up. The mode is saved in SPI NOR for next boot.
BUG=b:148604250
BRANCH=none
TEST=Build and test booting TGLRVP from NVMe and Optane
Check PCIe lane configuration.
Show all the NVMe devices
lspci -d ::0108
Show all the NVMe devices and be really verbose
lspci -vvvd ::0108
Print PCIe lane capabilities and configurations for all the NVMe devices.
lspci -vvvd ::0108 | grep -e x[124]
Print all the PCIe information of the device ae:00.0
lspci -vvvs ae:
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I25bc380697b0774cc30ad1b31ad785ee18822619
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39232
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These macros serve no purpose anymore, let's do the substitution
manually once and for all. Also update the comment on the macros
and fix whitespace on the touched lines.
TEST=Checked that there are no changes in compiled code.
Change-Id: Ib60f9ab157e2e7d44b551dd4f695a6c25ebeb405
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add configuration for all the PCIe Root ports and Clock Source.
Configure the Root Ports as disabled and clock sources as not used.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0a1ad7e056907e454a93f51c84e1d99f08b7bdef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39166
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Leave all the GPIOs in not connected state so that they can be
configured depending on the use-case. This is done to park the GPIOs in
a known safe state. This will also help to ensure that the required
GPIOs are configured when the concerned use-cases are enabled.
Below GPIOs are configured in Native Function 1 and are required for
boot-up.
* VCCIN_AUX_VID0
* VCCIN_AUX_VID1
* AP_SLP_S0_L
* PLT_RST_L
* CPU_C10_GATE_L
* GPDs
BUG=None
TEST=Build and boot the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5293536f66a6b08c9c2d2a6281684755a0c0b1b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39114
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- declare the FPMCU interrupt to be level-triggered
- change EC_PCH_WAKE_ODL gpio to native function mode
- corrected spelling of a signal name in a comment
BUG=b:144933687, b:148179954
BRANCH=none
TEST=none
Change-Id: I62da900d0b71139e55b52d06ec09ca25106f73cd
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This mainboard has the FSB BSEL straps wired to SuperIO GPIOs. They are
set up in romstage, so it makes no sense to clobber the registers with
garbage in ramstage.
Tested, my Asus P5G41T-M LX still boots and it does not need a full
reset on almost every reboot.
Change-Id: I6ea498119df44243ec42e3cb5c2903de32a17373
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39384
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This mainboard has the FSB BSEL straps wired to SuperIO GPIOs. They are
set up in romstage, so it makes no sense to rewrite their values in
ramstage.
Tested, my Asus P5QPL-AM still boots.
Change-Id: Ic47f96d12420ebcc70ab5cea940c4c09620c03ca
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Changes allow to use the integrated panel logic (power sequen-
cing and backlight control) for more connectors. The Kconfigs
GFX_GMA_PANEL_1_PORT and GFX_GMA_PANEL_2_PORT can now be set
to any port, e.g.
config GFX_GMA_PANEL_1_PORT
default "DP3"
Now that the panel logic is not tied to the `Internal` port
choice anymore, we can properly split it into `LVDS` and `eDP`.
This also adds Comet Lake PCI IDs which should still work the
same as Kaby and Coffee Lake.
Change-Id: I78b1b458ca00714dcbe7753a7beb4fb05d69986b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38921
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On Lenovo T500 the RTC readings where wrong, as RTC has
different encodings, depending on the statusB register.
Support BCD vs binary RTC format and AM/PM vs 24h RTC format.
Fixes wrong date and time on Lenovo 500.
Change-Id: Id773c33e228973e190a7e14c3d11979678b1a619
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/18498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
- Add a common page about Montevina ThinkPads.
- Describe how to disable ME and remove its firmware on these models.
- Describe vendor flash layouts.
Thanks to swiftgeek for his help when writing this, especially the last
paragraph and flash layouts.
Change-Id: I85917821efe63fff4b933b6226e99c17b63eb1b9
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The SCH5317 can have either 0x85 or 0x8c as device ID. However, the
former results in false positives on any ITE IT85xx series embedded
controller, which has led some people to think that chip was actually in
their laptops. Moreover, there is no register dump for the SCH5317.
Since nobody has touched this in over a decade, avoid further confusion
by dropping the misleading definition.
Change-Id: I4d1d34d1b88b878461499e52f1a916ee1e33210d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
To mitigate against sinkhole in software which is required on
pre-sandybridge hardware, the smm entry point needs to check if the
LAPIC base is between smbase and smbase + smmsize. The size needs to
be available early so add them to the relocatable module parameters.
When the smmstub is used to relocate SMM the default SMM size 0x10000
is provided. On the permanent handler the size provided by
get_smm_info() is used.
Change-Id: I0df6e51bcba284350f1c849ef3d012860757544b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Coverity detects pointer dev as FORWARD_NULL. Add sanity check
for dev to prevent NULL pointer dereference if dev did not point
to the audio device.
BUG=CID 1420208
TEST=Built image successfully.
Change-Id: I2a62da44c7044f9dc281eae0949f7f7b612ab238
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch upgrades the kernel space to v1.0 to accommodate EC hash,
which is used for CrOS EC's early firmware selection.
BUG=chromium:1045217
BRANCH=none
TEST=Boot Helios. Verify software sync works.
Cq-Depend: chromium:2041695
Change-Id: I525f1551afd1853cae826e87198057410167b239
Signed-off-by: dnojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Updating from commit id 8b9732f5:
2020-01-28 02:32:08 +0000 - (2lib: Fix struct vb2_hash the way it was
meant to be)
to commit id 5059062d:
2020-03-05 02:40:39 (EFS: Implement EFS2 and NO_BOOT mode)
This brings in 19 new commits.
Change-Id: Ic33500921e2c1a6109c24ad36713b41ab6e43de9
Signed-off-by: dnojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39324
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable DdiPortBHpd and additional pin muxes for DPs. These pin muxes
were done in FSPs, these pin muxes are for bypassing pin muxes in FSPs.
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board and check FSP log or DP port
pin mux from pinctl driver.
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Id44cfba696b1a21296278f4de2ad6de8f6bbd63b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39229
Reviewed-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
wpsw_boot is deprecated in favour of wpsw_cur. As such,
coreboot no longer needs to share "write protect" GPIO
with depthcharge.
BUG=b:124141368, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I2fcb7f82aa063fd72928171af5cbef0356ba620c
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:2088434
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39318
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Took less than 30 minutes, and booted on the first try :)
Working:
- Native raminit, using two 2GB DDR3-1333 DIMMs
- S3 suspend/resume
- USB ports and headers
- EHCI Debug with an FT2232H
- Gigabit Ethernet
- Integrated DVI/VGA outputs (libgfxinit)
- PCIe x16 for a graphics card
- PCIe x1 ports
- PS/2 port with a keyboard
- SATA controller
- Audio outputs, both front and rear
- flashrom, using the internal programmer. Tested with coreboot,
as well as with the vendor firmware. Backup chip is untested.
Untested:
- VGA BIOS for integrated graphics init
- Audio inputs
- Non-Linux OSes
- ACPI thermal zone and OS-independent fan control
Not working:
- Default IFD defines the BIOS region as the entire flash chip.
Using 'flashrom --ifd -i bios' is asking for a failed flash!
Change-Id: I467f586530e4a3b53a24b66565b5dcab5e33cf46
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This is an ATX mainboard with a LGA1155 socket and four DDR3 DIMM slots.
Porting was done using autoport and then doing a bunch of manual edits.
Working:
- All four DIMM slots
- Serial port to emit spam
- PS/2 keyboard
- S3 suspend/resume
- Rear USB ports
- Integrated graphics (libgfxinit)
- HDMI and VGA
- All PCIe ports
- Realtek GbE (coreboot must set the MAC address)
- Both PCI ports behind the ASM1083 PCI bridge
- SATA ports
- Native raminit
- Flashing with flashrom
- Rear audio output
- VBT
- SeaBIOS to boot Arch Linux
Untested:
- PS/2 mouse
- The other audio jacks
- EHCI debug
- Front USB headers
- Non-Linux OSes
Change-Id: Ia5d9176b6f435977ecdd4fc82fc4bc0974d8d6a4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
OCP platform Tiogapass is a 2-socket server platform, which
is based on a chipset including Intel Skylake-SP processors
and a Lewisburg PCH. Skylake-SP is a processor in Intel Xeon
Scalable Processor family.
Following ACPI tables are added:
DSDT/SSDT, MADT, FACP, FACS, HPET, MCFG, SLIT, SRAT, DMAR
This patchset is tested on a Tiogapass board. It booted with
Linux kernel 4.16.0; lscpu command shows all 72 cpus (2 sockets,
18 cores, 2 thread per core); ssh command shows
networking is up from Mellanox ConnectX-4 PCIe NIC card.
Towards successful gerrit buildbot build, note that:
* microcode is in coreboot intel-microcode submodule repo.
* IFD binary is included in this patch.
* Dummy ME binary is used, as it may take long time for Intel
ME binary to be available in public domain.
* Fake FSP binary is used, as at this moment the SKX-SP
FSP binary is not going to be available in public domain.
Known issues (Not intend to address in this initial support for
Xeon-SP processors):
* c6 state is not supported.
* dsdt table is not fully populated, such as processor/socket
devices, some PCIe devices.
* SMM handlers are not added.
Following are some command execution with CentOS booted from
local SATA disk:
[root@localhost ~]# lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 72
On-line CPU(s) list: 0-71
Thread(s) per core: 2
Core(s) per socket: 18
Socket(s): 2
NUMA node(s): 2
Vendor ID: GenuineIntel
CPU family: 6
Model: 85
Model name: Intel(R) Xeon(R) Gold 6139 CPU @ 2.30GHz
Stepping: 4
CPU MHz: 140.415
BogoMIPS: 4626.46
Virtualization: VT-x
L1d cache: 32K
L1i cache: 32K
L2 cache: 1024K
L3 cache: 25344K
NUMA node0 CPU(s): 0-17,36-53
NUMA node1 CPU(s): 18-35,54-71
[root@localhost ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.23.68.190 netmask 255.255.0.0 broadcast 172.23.255.255
inet6 2620:10d:c082:9063:268a:7ff:fe57:5af0 prefixlen 64 //cut
inet6 fe80::268a:7ff:fe57:5af0 prefixlen 64 scopeid 0x20<link>
inet6 2620:10d:c082:9063::5d2 prefixlen 128 scopeid 0x0<global>
ether 24:8a:07:57:5a:f0 txqueuelen 1000 (Ethernet)
RX packets 84249 bytes 6371591 (6.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8418 bytes 748781 (731.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 613 bytes 63906 (62.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 613 bytes 63906 (62.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[root@localhost ~]# cbmem
36 entries total:
// Lines were cut to avoid checkpatch.pl warnings
Total Time: 96,243,882,140,175,829
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Tested-by: johnny_lin@wiwynn.com
Change-Id: I29868f03037d1887b90dfb19d15aee83c456edce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
This patch adds support for Intel Xeon-SP.
This patch is developed and verified with Skylake Scalable
Processor, which is a processor in Xeon-SP family. The code
is expected to be reusable for future geneations of Xeon-SP
processors, and will be updated with smaller targeted
patches accordingly, to add support for additional Xeon-SP
processors, to add features, and to improve the code base.
The Skylake-SP FSP is based on FSP 2.0. The FSP is a
proof-of-concept build. The binary is not shared in public,
when this patch is upstreamed.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Tested-by: johnny_lin@wiwynn.com
Change-Id: Idc9c3bee17caf8b4841f0bc190cb1aa9d38fc23e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
CB:38541 ("ec/google/chromeec: Add SSDT generator for ChromeOS EC")
added a new device_operations structure for chromeec for handling ACPI
SSDT generation. However, this resulted in the original
device_operations which handled lpc read resources to be skipped. This
change fixes the above regression by combining the device operations
for reading resources and ACPI SSDT generation into a single structure
and retains the old logic for enabling of pnp devices.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I3a242f4b15603f957e0e81d121e5766fccf3c28d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The register TCO1_STS is never cleared, which will cause SMIs to either
retrigger over and over again (e.g. TIMEOUT) or prevent concurrent
interrupt events, depending on which event triggered.
Clear both TCO2_STS and TCO1_STS.
This also fixes the issue where SECOND_TO_STS will always end up set in
the SMI handler by unconditionally (re)setting it.
Tested on X11SSM-F, where enabling TCO caused the terminal to get
flooded with SMI debug messages. With this patch, a message gets written
every ~1 second.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ia57c203a672fdd0095355a7e2a0e01aaa6657968
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39259
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The TX window will offset to edge during DVFS switch, which may cause
TX data transmission error and random kernel crash. Therefore, use the
standard dqsosc (DQS Oscillator) for TX window tracking.
BUG=b:142358843
BRANCH=kukui
TEST=Boots correctly on Kukui
Change-Id: Idcf9213a488e795df3faf64b03588cfe55cb2f81
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Because eMCP and discrete DDR devices have different DVFS tables, their
EMI bandwidth thresholds should also be different. When the EMI total
bandwidth reaches the threshold, the system will notify DVFS module to
perform DVFS switch for system performance in low power states.
This patch increases the threshold from 0xa to 0xd for eMCP DDR devices
so that DVFS switch will be less likely to happen.
The register table of EMI_BWCT0 is incorrect in the datasheet. According
to the hardware design, BW_2ND_INT_BW_THR should be in bits [30:24]
instead of [22:16]. However, the logic in DRAM driver is correct,
aligned with the hardware design, so we don't need to correct it.
BRANCH=kukui
BUG=b:142358843
TEST=bootup pass
Change-Id: I82c3c70bcd90df3fdd613c0353aba0f176bc82bc
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39034
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allows to override the PortUsb20Enable and PortUsb30Enable FSP options
(which are set to 1 by default) to enable/disable USB ports if the
usb_config_override flag is set to "1". Therefore, these changes will
not affect other boards with an Apollo Lake processor.
Change-Id: Ia94a2be1647f7743ef0c918ae3b34437a179261c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enable VBOOT support on all devices that have a 12 MiB flash, using
RW_MAIN_A + RW_MAIN_B partition, allowing the use of tianocore payload
in both RW_MAIN_A, RW_MAIN_B and WP_RO.
* Add VBNV section to cmos.layout
* Add FMAP for VBOOT
* Select Kconfigs for VBOOT
* Enable VBOOT_SLOTS_RW_AB by default
The VBNV is intentionally not covered by the CMOS checksum.
Tested on x230 and T440p.
Change-Id: I8a35a06ece1e9d57a2ef23970e61ae26fafce543
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Jonas Moehle <ad-min@mailbox.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
This is a port of https://review.coreboot.org/c/coreboot/+/22337 to the
Haswell northbridge. This code is necessary to support the dGPU of the
t440p. Code was cut and pasted from Sandy Bridge with vendor IDs updated
to the correct Haswell values. Tested on t440p with dGPU on Ubuntu
18.04.4 with 5.3.0-28 kernel. Without patches dmesg reports Nouveau is
unable to read the VBIOS of the dGPU as it has an invalid checksum (I
checked that the ROM in CBFS is correct). With this patch DRM works
correctly with both the Nouveau driver and the Nvidia proprietary
driver. Windows 10 1909 also tested but generates bluescreen once GPU
driver is loaded.
Change-Id: Ie5f089fb6fd774e6c61f4f9281e2945bd44edf27
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use the ifdtool --output flag to modify coreboot.pre inplace, instead
of using the `mv` command to get the same result. In this way the stdout
will make more sense in the build context.
Change-Id: I6dacc8b39052801c770c02fa2aa1b526747ae496
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If the ChromeOS EC uses EC early firmware selection (EFS), the AP vboot
build must also enable EC EFS. Puff EC uses EFS, so enable it in the AP
vboot build.
BUG=b:150742950
TEST=Puff can boot with EC EFS with hardware write protect enabled
BRANCH=none
Signed-off-by: Sam McNally <sammc@chromium.org>
Change-Id: I0877000b7d277106436831f2d69775c25299da9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This reverts commit c8b0f31ca1.
Bumping the FADT table version from 3 to 6 causes
Windows 10 to BSOD with an ACPI BIOS error or simply
fail to boot on multiple platforms (Haswell, Broadwell,
Braswell, Skylake). Revert until the issue can be properly
identified and corrected.
Change-Id: I261d953321df2616a3f1c3460a535b57a8848315
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Otherwise there will, after make gitconfig,
be (hidden) shell command failures with 'git commit -s':
gmake: util/lint/check-style: Command not found
gmake: *** [Makefile.inc:632: check-style] Error 127
Change-Id: I3891dee53702ee10e5e44dae408193e49d7a89f1
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38227
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BSD grep (on macOS) doesn't like repeated repetition operators, it
throws the error
grep: repetition-operator operand invalid
This removes the superfluous repetition operator to make the commit-msg
hook work on macOS and other platforms not using GNU grep.
Change-Id: Id0f57d0f14634f7844b889d71342b2982fcadeb2
Signed-off-by: Patrick Elsen <pelsen@xfbs.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The memNTrainFlowControl array is generating Coverity warnings
in multiple places in code where it attempts to write to index 1.
The array is defined as either 2 elements or 1 of NULL depending
on #if (AGESA_ENTRY_INIT_POST == TRUE). This is likely a false
alarm from Coverity (memory should not be training outside of a
POST), but adding a second NULL element for the
AGESA_ENTRY_INIT_POST == FALSE case. Tested on Lenovo G505s.
Change-Id: Iaebe0830471e1854d6191c69cdaa552f900ba7a6
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1357451, 1357452, 1357453
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38176
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Potential for out-of-bounds read. However, this code is not
used on F14, F15tn, or F16kb platforms. As can be seen in
vc/amd/agesa/f15tn/Config/PlatformInstall.h only multiple
socket F10 is supported. Tested on Lenovo G505s.
Change-Id: Ib71fe32d89840b9f25619d74980e562fd626952b
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241831
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
AllocParams.Persist is used uninitialized when calling
HeapAllocateBuffer. This could lead to unpredictable or
unintended results. The f15tn and f16 versions of
AmdS3Save.c have already addressed this by initializing
AllocParams.Persist=0 in the same location in the code,
so adding to f14 only.
Change-Id: I2cbfbc4ad14a861e0cd92f130209b3b0f5b76a17
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Uninitialized variable will contain an arbitrary value left from
earlier computations. This issue has already been addressed
in the f15tn and f16kb versions of this same file, so am
backporting the fix.
Change-Id: Id876107265689e08ad6760e514a4911f32b53da7
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241856
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38048
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The generic MemNProgramNbPstateDependentRegistersUnb function is unused,
and generates a Coverity warning of an unused switch case. Only family
specific versions of this function are called elsewhere. Delete unused
function.
Change-Id: I2afc83861f4b3a13bfc1eef4920cd3023e608e94
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241810
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38493
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GNU Make 4.3 doesn't propagate a global .SILENT to sub-processes
anymore. Let's make it explicit to maintain the behaviour we are
used to.
From the changelog:
[SV 54740] Ensure .SILENT settings do not leak into sub-makes
Change-Id: I3de51c245d3344b062dc0fe9c62b8d5c0ac5e67d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The current elog implemetation searches for an active PME status bit by
iterating the PCI devices. On disabled or hidden devices a BUG gets
triggered: BUG: pch_log_rp_wake_source requests hidden ...
This is caused by the use of the PCH_DEV_* macros which resolve to
_PCH_DEV and finally call pcidev_path_on_root_debug.
Disabled devices are skipped already so we can safely use the DEVFNs
instead, circumventing the BUG.
Change-Id: Id126e2c51aec84a4af9354b39754ee74687cefc8
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Leverage the common sku id space helper encoders.
dedede uses the non-legacy SKU ID space.
squash in,
mainboard/google/dedede: Migrate onto get fw_config helper
BUG=b:149348474
BRANCH=none
TEST=only tested on hatch
Change-Id: I0c21a748fddef0985022cb4e77a8db95d6692f4b
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Leverage the common sku id space helper encoders and
set the sku id max to 0xff for legacy to ensure we
behave the same.
BUG=b:149348474
BRANCH=none
TEST=tested on hatch
Change-Id: I60a37a5f9659b8df4018872956f95e07a3506440
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add an optional commandline flag to define the filename of the resulting
output file. If this flag is not defined, it will behave like before by
using the old filename with a ".new" suffix.
With this additional flag it is not necessary to move the output file at
build-time, and the stdout print "Writing new image to <filename>" makes
more sense in the build context.
Change-Id: I824e94e93749f55c3576e4ee2f7804d855fefed2
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add gpio definition for Jasper Lake gpio controller.
Also created a separate file for JSL and TGL gpio keeping common asl file.
gpio_soc_defs.h must pass correct information/macro values to asl file
for code to work.
GPIO controller includes 4 gpio community and 10 groups. Patch adds
definition for all gpio within community and groups
Updated IRQ mapping for all gpios
TEST=Check if jslrvp and tglrvp code is compiling
Change-Id: Iae4e694ecb30658e43c5ed99e5436579fd7d2ed2
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
For a very long time, SeaBIOS sometimes failed to build when using
multiple threads. This known problem has been haunting everyone for a
very long time. Until now.
Unlike most other payloads, building SeaBIOS results in two files: the
SeaBIOS payload itself and SeaVGABIOS. Each file has its own target, and
there's a third target called "seabios", which has the same recipe as
the SeaBIOS file, which calls `payloads/external/SeaBIOS/Makefile` with
a bunch of arguments. In addition, SeaVGABIOS depends on "seabios".
When executing serially, if the file of either SeaBIOS or SeaVGABIOS is
needed, the SeaBIOS Makefile will be run. This will generate both files,
so it is not necessary to run the Makefile more than once.
However, when using multiple threads, it can happen that one thread
wants to make the SeaBIOS file, while another one wants to make the
SeaVGABIOS file, which depends on "seabios". This implies that both
threads will execute the SeaBIOS Makefile at about the same time, only
to collide when performing git operations. Since git uses a lock file
when updating the index, one of the threads will fail to acquire the
lock with an error, which will ultimately cause the build to fail.
Whenever this happened, manually aborting with Ctrl-C made the build
process fail again because of the same error. The only way to get past
this problem, other than using one thread, was to let the unfinished
jobs complete. The thread that acquired the lock on the SeaBIOS git
repository would finish building SeaBIOS, so that target would not need
to be remade. When restarting the build, only the target that failed is
rebuilt, so it does not collide with any other thread.
To address this issue, make the SeaVGABIOS file target depend directly
on the SeaBIOS file instead, and remove the duplicate "seabios" target.
Change-Id: I251190d3bb27052ff474f3cd1a45022dab6fac31
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
All boards using this code use i82371eb (that shares PCI ID with i82371ab).
Dropping the code lightens compressed ramstage by a few dozen bytes.
Change-Id: Iab1e83b8f5fff44a33619c7925e5448169a2a87c
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38598
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
XOE# and XDIR# can be used as GPOs 23/22 if X-Bus functionality is not
required. Turns out asus/p2b-ls is using them to control termination
for the onboard SCSI buses. Add support to allow this reconfiguration.
Change-Id: I2dab6fafbd67a98ed1cac1ffcf9352be4a87c3e9
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Relocate the first size check. This was automatically continuing
and not looking for the caller incorrectly passing a destination.
New information indicates that the APOB_NV should always be present
in the system. Augment the missing size check to inferring whether
a missing size is valid, as in the case of older products, or truly
missing when it's needed.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I51f5333de4392dec1478bd84563c053a508b9e9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Fix two out-of-bounds reads in lz4 decompression:
1) LZ4_decompress_generic could read one byte past the input buffer when
decoding variable length literals due to a missing bounds check. This
issue was resolved in libpayload, commonlib and cbfstool
2) ulz4fn could read up to 4 bytes past the input buffer when reading a
lz4_block_header due to a missing bounds check. This issue was resolved
in libpayload and commonlib.
Change-Id: I5afdf7e1d43ecdb06c7b288be46813c1017569fc
Signed-off-by: Alex Rebert <alexandre.rebert@gmail.com>
Found-by: Mayhem
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
cbfs_get_handle() and cbfs_get_attr() are both looping over elements to
find a particular one. Each element header contains the element's
length, which is used to compute the next element's offset. Invalid or
corrupted CBFS files could lead to infinite loops where the offset would
remain constant across iterations, due to 0-length elements or integer
overflows in the computation of the next offset.
This patch makes both functions more robust by adding a check that
ensure offsets are strictly monotonic. Instead of infinite looping, the
functions are now printing an ERROR and returning a NULL value.
Change-Id: I440e82fa969b8c2aacc5800e7e26450c3b97c74a
Signed-off-by: Alex Rebert <alexandre.rebert@gmail.com>
Found-by: Mayhem
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The VBOOT code can be compiled but it asserts with:
ASSERTION ERROR: file 'src/security/vboot/common.c', line 40
Start VBOOT in bootblock to fix the assertion.
Tested on Lenovo X220:
The assertion is gone, the platform boots again.
Change-Id: I48365e911b4f43aecba3b1f950178b7ceed5b2e9
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Some of the revision 4 FADT fields were already updated to ACPI
spec revision 6, but not all of them. In addition the advertised
FADT revision was 3.
Implement all fields as defined in version 6 and bump the advertised
FADT revision to 6.
Change-Id: I10c1e2517df41159ab9b04f763d3805ecba50ffa
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add a tutorial how to use ME cleaner, and give some basic steps to
strip the ME. Update the Lenovo Sandy Bridge documentation that no
issues could be observed on X220 and give an example flash layout.
Tested on Lenovo X220 with stripped ME and found no issues:
commit: cbc5b99ac9
* Displayport
* VGA
* USB
* Bluetooth
* Wifi
* Wifi-kill switch
* libgfxinit
* SATA
* Audio
* SD-card
* Ethernet
* Keyboard
* Fn-Keys
* Display brightness
* ACPI S3 resume
* Battery events
* CPU temperature reporting
* FAN managment
* Stress test stable
* Youtube videos over Wifi
* stress -c 2 -m 1 -d 1
* glxgears
Change-Id: I0b1d04f00b5dbb38cf04333f2b345749b740a375
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39129
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move print_me_fw_version(), remove print_me_version/dump_me_version from
cnl/skl/apl and make changes to call print_me_version() which is defined
in the CSE lib.
TEST=Verified on hatch, soraka and bobba.
Change-Id: I7567fac100b14dc207b7fc6060e7a064fb05caf6
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This patch includes the change required to display Apollo Lake platform
information which reports CPU, MCH, PCH and IGD information in romstage.
BUG=None
TEST=
1. Boot to OS on Bobba board.
2. Verified below info from CPU Console log in romstage
CPU: Intel(R) Celeron(R) N4000 CPU @ 1.10GHz
CPU: ID 706a1, Geminilake B0, ucode: 00000031
CPU: AES supported, TXT NOT supported, VT supported
MCH: device id 31f0 (rev 03) is Geminilake
PCH: device id 3197 (rev 03) is Geminilake
IGD: device id 3185 (rev 03) is Geminilake EU12
Change-Id: Id4edfeae7faee9f5f80698cf34b31fdcb066a813
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38824
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Linux expects a working PSCI and hangs if not found.
Add BL31 into CBFS as '-M virt,secure=on -bios ' commands line arguments cause
qemu's internal PSCI emulation to shutdown.
BL31 is placed in qemu's SECURERAM memory region and won't conflict with
resources in DRAM.
Tested on qemu-system-aarch64:
Fixes a hang and allows to boot into Linux 5.4.14 userspace.
Change-Id: I809742522240185431621cc4fd8b9c7deaf2bb54
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Replace DSDT ACPI code and DSDT injection with a SSDT only solution.
The current implementation shows some issues on current Linux, which
might be due to external ACPI objects, which are then injected into
DSDT or the fact that those objects only use 3 characters.
Replace all the DSDT code with an SSDT generator.
Tested on HP Z220:
Boots into Linux with no ACPI errors. The SSDT can be disassembled.
Change-Id: I41616d9bf320fd2b4d8495892b8190cd2a2d057f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change is mainly to control PlatformDebugConsent FSP UPD.
PlatformDebugConsent is enabled if SOC_INTEL_<SOC>LAKE_DEBUG_CONSENT != 0.
PlatformDebugConsent in FspmUpd.h has the details.
TEST=Able to connect ITP/DCI with target system.
Change-Id: I39fe84025cb2bff186d61b2fcad531db52e2b440
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
As the SSDT generator for LDNs expects a "parent" PNP device
for proper ACPI code generation, validate that it is present.
Make sure the devicetree looks as expected and print a BUG message
if that's not the case.
Tested on HP Z220:
No BUG message was printed.
Change-Id: I6cbcba8ac86a2a837e23055fdd7e529f9b3277a2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Leverage the common sku id space helper encoders.
volteer uses the non-legacy SKU ID space.
BUG=b:149348474
BRANCH=none
TEST=only tested on hatch
Change-Id: Ic66908afb7abb34527b4177cfd07f03ad718317c
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Leverage in Puff to avoid diskswap variants. Later this could become
part of the baseboard definition and hatch diskswap variants migrated
over to use it as well.
BUG=b:149171631
BRANCH=none
TEST=Swap between x4 NVMe drives and 2x2 Teton Glacier hybrid drives and
run lsblk, lspci, and nvme tools to confirm dynamic PCIe configuration
on Puff.
Change-Id: Ie87f0823f28457db397d495d9f1629d85cfd5215
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The following plumbs through the enabling of Intel's TetonGlacierMode
allows for reconfiguring the PCIe lanes at runtime for hybrid drives
to be accessable via devicetree.
BUG=b:149171631
BRANCH=none
TEST=Swap between x4 NVMe drives and 2x2 Teton Glacier hybrid drives and
run lsblk, lspci, and nvme tools to confirm dynamic PCIe configuration
on Puff.
Change-Id: Id9a72161494db6a4da4abd3302b06df7c70634ab
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The following introduces helpers that, by default,
accommodate a larger SKU id space. The following
is the rational for that:
Allow INT32_MAX SKU id encodings beyond UINT8_MAX.
This allows for the SKU id to accommodate up to 4 bytes
however we reserve the highest bit for SKU_UNKNOWN to be encoded.
However, the legacy UINT8_MAX encoding is supported by leveraging
the Kconfig by overriding it with the legacy max of 0xff.
Follow ups migrate boards to this common framework.
V.2: Fixup array size && drop sku_id SKU_UNKNOWN check and pass
whatever is set to userspace as firmware doesn't care about
the value.
V.3: Use SPDX-License header.
BUG=b:149348474
BRANCH=none
TEST=tested on hatch.
Change-Id: I805b25465a3b4ee3dc0cbda5feb9e9ea2493ff9e
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update memory parameters based on memory type supported by Tiger lake RVP
1. Update dq/dqs mappings
2. Update spd data for Tiger lake LPDDR4 SAMSUNG/MICRON memory
3. Add SPD data bin files for supported memory types
4. Update other FSPM UPDs as part of memory initialization
BUG=none
BRANCH=none
TEST= build tglrvp flash and boot to kernel
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I7248862efd1dcd5a0df0e17d39b44c168caa200e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Correct the offset for the Topstar driver enable/disable bit,
which was off by 2 bits compared to a dump of the AMI UEFI ACPI.
This prevents the fan mode (FANM) from being inadvertently changed
and hopefully fixes some intermittent issues with fan speed on
resume from suspend.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: Ibc3c39d5b14c753eed6d1ed8cbf161717f8d04e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39105
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The indirection of names is exceedingly confusing for ultimately the single
interrupt trace of EC_PCH_WAKE_ODL between the EC gpio#74 to GPD2/LAN_WAKE# on
the PCH side.
This helps folks chase this indirection down through the code.
BUG=b:147026979
BRANCH=none
TEST=builds
Change-Id: I35d746a202dae06d2f6f1edfaa3889864b09f50d
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
WWAN wake event is routed to GPP_D0 GPIO and Pen Detect wake event is
routed to GPP_C12 GPIO. Update the GPE configuration accordingly.
BUG=None
TEST=Build the mainboard.
Change-Id: Id36d2c8265a0b7ea241565f6bb723df6b37446fa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch makes all legacy 8254 FSP UPDs (Enable8254ClockGating and
Enable8254ClockGatingOnS3) depend on CONFIG_USE_LEGACY_8254_TIMER to
avoid discrepancy between S0 and S3 resume flow.
TEST=Able to boot to TianoCore without any hangs and errors, also
verified S3 resume path doesn't clock gate 8254 timer using FSP-S UPD.
Change-Id: Id6fe74a51537abbb9ff48db925e37a64e5b21f78
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39110
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The specified PNP registers PNP_MSC0-E (F0-FE) are part of the iLPC2AHB
bridge's index/value interface. They are no one-time config registers
so we can't specify a sane value in the devicetree.
Thus, drop them to stop coreboot from complaining about the missing
entries.
Change-Id: I7d7f16845c755592317f140cca66cca12032f7a6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
When specifying _PAD_CFG_STRUCT with raw hex values, a logical reset
value of 0x0 is only defined for GPD pads. For any other GPIOs this maps
to 0x3.
On the Supermicro X11 boards a value of 0x0 is set for GPP_D22 and
GPP_F23, triggering the error "gpio_pad_reset_config_override: Logical
to Chipset mapping not found".
Set the right value (0x3<<30) for the affected GPIOs.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I3ae17dfc4d90f88f5b8bc5bee49740745778a91a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch cleans soc/intel/{cnl, icl, tgl} by moving common
soc code into common/block/cse.
Supported SoC can select existing HECI_DISABLE_USING_SMM option to
select common cse code block to make heci function disable using
sideband interface during SMM mode at preboot envionment.
BUG=b:78109109
TEST=Able to make HECI disable in SMM mode successfully without any hang
or errors in CNL, ICL and TGL platform.
Change-Id: I22a4cc05d3967c7653d2abe2c829b4876516d179
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26133
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The coverity project is done, for the most part, so drop it. Expand
a bit on the scope of the toolchain binary project, and point out
that the Ghidra project already has code from GSoC 2019 but could be
developed further.
Change-Id: I7342cc3133494f69b175b11b1f8342a0f40840e7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
When compiling with GCC, use the special wrappers around ar and nm that
provide the path to the plugin they need to understand LTO object files.
These wrappers forward all other functionality to the underlying
programs, so they should otherwise be equivalent.
Change-Id: Ibdae4faabf67bf6a4bb8c38970f6189646ee74b3
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38290
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Default FSP values for "GtFreqMax" and "CdClock" UPDs are "Auto", hence
related FSP-S UPD override can be avoided from coreboot.
As per FSP-S UPD Header (FspsUpd.h)
/** Offset 0x020E - GT Frequency Limit
0xFF: Auto(Default)
**/
UINT8 GtFreqMax;
/** Offset 0x0209 - CdClock Frequency selection
0: (Default) Auto
**/
UINT8 CdClock;
TEST=Able to get Pre-OS display on ICLRVP and Dragonegg platform.
Change-Id: Ie500dd5fad5cd358ea3fad4d5c0be1b0c148584b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
This change creates gfx directory under drivers/ so that all drivers
handling gfx devices can be located in the same place. In follow-up
CLs, we will be adding another driver that handles gfx devices.
This change also updates the names used within the driver from
*generic_gfx* to *gfx_generic*. In addition to that, mainboard
drallion using this driver is updated to match the correct path and
Kconfig name.
TEST=Verified that drallion still builds.
Change-Id: I377743e0f6d770eed143c7b6041dab2a101e6252
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
As part of vboot1 deprecation, remove an unused vboot_struct.h
include. coreboot is now free of vboot1 data structure use.
One vboot_api.h include remains as part of security/vboot/ec_sync.c.
BUG=b:124141368
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I042d692aa252f8f859d4005455eb6a2eabc24a87
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Remove MAC address pass through because when MAC address pass through setting
change to "Use dock built-in MAC address", the MAC address always keeps the VPD
value.
BUG=b:149813043
TEST=tested on sarien and the result as below.
(Option) (Result)
- Use pre-assigned MAC address : Pass
- Use Chromebook built-in address : Pass
- Use dock built-in MAC address : Pass
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ia85ef6ed0c4db82301375edd0968cf7dd2f62dc1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Commit 6ae8b50 [chromeec: Depend on events_copy_b to identify wake source]
partially broke resume from suspend on Auron and Slippy variants when
multiple events exist in the EC event queue. In the case of the device
suspending manually and then subsequently having the lid closed, the device
will be stuck in a resume/suspend/resume loop until the device is forcibly
powered down.
Mitigate this by clearing any pending EC events on S3 wakeup.
Test: build/boot several Auron/Slippy variants, test suspend/resume functional
with both single and multiple events in EC event queue.
Change-Id: I7ec9ec575d41c5b7522c4e13fc32b0b7c77d20d9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Remove MAC address pass through because when MAC address pass through setting
change to "Use dock built-in MAC address", the MAC address always keeps the VPD
value.
BUG=b:147994020
TEST=tested on drallion and the result as below.
(Option) (Result)
- Use pre-assigned MAC address : Pass
- Use Chromebook built-in address : Pass
- Use dock built-in MAC address : Pass
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I1f58e98187feb4e428ca75f7e82c464567528526
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
This patch makes all bit field macro definition for SMI_STS register
(offset 0x44) be consistent i.e. ending with "_STS_BIT".
Also modified relevant files where those macros are getting used.
Change-Id: Ibe3fbb459c106a3a58cd9a8b6eb3d7ee92e6ed82
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
create_coreboot_variant.sh and kconfig.py have moved to the chromium
repo, in src/platform/dev/contrib/variant (see crrev.com/c/2052338),
so remove them from the coreboot repo.
BUG=b:149410618
BRANCH=None
TEST=N/A
Cq-Depend: chromium:2052338
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: Ie27f68bfd978be5e2b1a2f0789d574749825f6fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Originally, this patch made 'BIOS' uppercase in the referenced comment
and converted the C++ style to be consistent with the remainder of
the function. Somewhere, the 'BIOS' became uppercase creating a merge
conflict.
Now this CL converts the C++ style to be consistent with the remainder
of the comments.
Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov>
Change-Id: I85d78b5e08a7643c3d87e3daf353d6b3ba8d306b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38854
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The STM is a part of the core VTx and using ENABLE_VMX will make the
STM option available for any configuration that has an Intel
processor that supports VTx.
Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov>
Change-Id: I57ff82754e6c692c8722d41f812e35940346888a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38852
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Check to ensure that dual monitor mode is supported on the
current processor. Dual monitor mode is normally supported on
any Intel x86 processor that has VTx support. The STM is
a hypervisor that executes in SMM dual monitor mode. This
check should fail only in the rare case were dual monitor mode
is disabled. If the check fails, then the STM will not
be initialized by coreboot.
Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov>
Change-Id: I518bb2aa1bdec94b5b6d5e991d7575257f3dc6e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Previously the PRTs were defined in southbridge code (8014714
southbridge/intel/bd82x6x/acpi: Fix IRQ warnings), but this was lost
when southbridge PRTs became autogenerated. Add the proper PRTs for the
PCI express for graphics root ports.
This (again) fixes warnings issued by Linux for interrupts on secondary
functions of devices on the PEG ports, such as the HDMI audio controller
on graphics cards.
pcieport 0000:00:01.0: can't derive routing for PCI INT B
snd_hda_intel 0000:01:00.1: PCI INT B: no GSI
Tested with GIGABYTE P67A-UD3R (CB:31363) with Radeon HD 5670.
Change-Id: Ic429ec2fdeadb9dab1c03916974e173004d6cd16
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The comment is no longer relevant. Perhaps the intention had been
to modify the names of the files delivered from AMD in order to
simplify Makefile.inc.
AMD firmware is distributed via the new amd_blobs repo and the
filenames match the blobs as they are released. Multiple Family 15h
devices are supported by this directory and their SMU Firmwares do
not all follow identical naming convention.
Keep the existing functionality and reword the comment.
BUG=b:120118850
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Ifbf8e2286f34bc37a6178c37f8c412ec51ee02c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tigerlake irq.h and pci_irqs.asl have differences compared to
Jasperlake. Hence renaming irq.h as irq_tgl.h and pci_irqs.asl as
pci_irqs_tgl.asl
Also adding a new file irq_jsl.h and pci_irqs_jsl.asl for Jasperlake
SoC and allowing irq.h and pci_irqs.asl to choose the correct file based
on SoC selected.
BUG=None
BRANCH=None
TEST=Compilation for Jasperlake board is working
Change-Id: Ia8e88f92929fe40d7be1c28947e005cb0d862fcb
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
PCH_DEV_P2SB already covers both __SIMPLE_DEVICE__ cases. The values are
only used for PCI-config access functions, which also check for NULL
when necessary.
The PCI_DEV_INVALID case can't occur by definition, and if we wanted to
check, we could do so at compile time using _Static_assert().
Change-Id: I400fc20133809aaa0fd0519531a62ec9b8812ef1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
The NEED_VB20_INTERNALS switch is being deprecated.
Use the header file vb2_internals_please_do_not_use.h instead.
BUG=b:124141368, chromium:957880
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ie35644876178b806fab4f0ce8089a556227312db
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:2055600
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Use vb2api_get_recovery_reason() API function rather
than accessing vb2_shared_data internals.
Of all the vanilla verified boot code in coreboot,
this is the last remaining use of vboot's internal
data structures in coreboot. There remains only one
sole instance in Eltan's code.
BUG=b:124141368, chromium:957880
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I845c9b14ffa830bc7de28e9a38188f7066871803
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:2055662
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Updating from commit id 0e97e25e:
2020-01-28 02:32:08 +0000 - (2lib: Fix struct vb2_hash the way it was meant to be)
to commit id 8b9732f5:
2020-02-18 05:55:01 +0000 - (vboot: do not call vb2_commit_data at end of VBSLK)
This brings in 36 new commits.
Change-Id: Icb0ab2c82c3264185171a32357944949afd2edce
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
FSP-T takes microcode pointer and location parameters, and FSP-T is
invoked before CAR is set-up and before memory is trained. So it is not
possible to modify supplied microcode pointer in runtime. Because of
that we have to hardcode the pointer in bootblock.
Also, current FSP-T on Xeons require microcode (it is not optional).
Reasons for that are currently unclear and are being investigated.
However for the present time we need to be able to add microcode at a
certain offset so FSP-T can be used.
TEST=test on OCP TiogaPass board, as well as out-of-tree CPU/board
Change-Id: I6c02601a7ac64078e556e2032baeccaf27f77da2
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
The serial number and UUID returned by DMI are retrieved from VPD.
The solution supports a 16 character "serial_number" and a 36 character
"UUID" string.
BUG=N/A
TEST=tested on monolith
Change-Id: I0b6ce769cfa81a1e248a35f6149b7d1bbcf1f836
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Below helper function is added:
cse_wait_com_soft_temp_disable() - It polls for CSE's operation mode
'Soft Temporary Disable'. CSE enters this mode when it boots from
RO(BP1) partition. The function must be called after resetting CSE to
wait for CSE to enter 'Soft Temporary Disable' Mode.
BUG=b:145809764
Change-Id: Ibdcf01f31b0310932b8e834ae83144f8a67f1fef
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
In this patch, name.c file that includes the function definition for
fill_processor_name which is used by the report_cpu_info function is been
made available in romstage.
This is done to facilitate the report_platform_info to be called from
romstage, as the intention is to move the report_platform_info to romstage
for all SOC's due to the bootblock size constraint.
BUG=None
TEST=Build and boot APL, GLK and CNL platforms.
Change-Id: Ifd6d4b80c2e07d02adaed676a56efeb6fb704552
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Upcoming patches for the Linux kernel (5.6 ?) would like to consume
information about the USB PD ports that are attached to the device. This
information is obtained from the CrOS EC and exposed in the SSDT ACPI
table.
Also, the device enable for this PCI device is moved from ec_lpc.c to
a new file, ec_chip.c, where EC-related ACPI methods can live. It
still allows other code to call functions on device enable (so that
PnP enable for the LPC device still gets called).
BUG=b:146506369
BRANCH=none
TEST=Verify the SSDT contains the expected information
Change-Id: I729caecd64d9320fb02c0404c8315122f010970b
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Since CB:37231 [1], the vboot working data has been replaced with vboot work
buffer, so corrrect the help text of option VBOOT_STARTS_IN_ROMSTAGE
accordingly.
[1] security/vboot: Remove struct vboot_working_data
BRANCH=none
BUG=chromium:1021452
TEST=none
Change-Id: I80783274179ae7582bbb4c8f9d392895623badce
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Some Volteer variants might not use SPD files. Allow SPD_SOURCES in
spd/Makefile.inc to be empty.
BUG=None
BRANCH=None
TEST=Build coreboot and see that it builds without error
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: I5a8231b999e16503867d3c8df571b11fa0c1f6a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
thinkpad_acpi maps the battery hotkey (KEY_BATTERY) on scancode 0x01 and
the lock hotkey (KEY_COFFEE) on scancode 0x02.
On the Thinkpad X1 Carbon (and possibly others), the hotkeys for Fn-F2
and Fn-F3 are different from the default one so a new layout has to be
defined.
Change-Id: Ib2d96be1a7815d7d03e6e8c6d300fd671c8598ca
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Enable Access Control Services and Advanced Error Reporting for PCI Express
bridges in order to have PCIe devices in separate IOMMU groups for correct
passthrough.
TEST=run dmesg on Debian Buster on PC Engines apu2 and check whether PCIe
devices have separate groups
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I10a8eff0ba37196692f9db6519e498fe535ecd15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The `chars` pointer references the heap which is part of the payload
and relocated along with it. So calling phys_to_virt() on it was
always wrong; and the virt_to_phys() at its initialization was a
no-op anyway, when the console was brought up before relocation.
While we are at it, add a null-pointer check.
Change-Id: Ic03150f0bcd14a6ec6bf514dffe2b9153d5a6d2a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
When the bit for interlaced mode is not set, a trailing space is added
to the end.
As the space is already accounted for in `" interlaced"`, remove that
space.
TEST=Boot on Lenovo X60t, and verify the trailing space in the detailed
mode is gone.
Change-Id: I4114c9e61a040fa005c806404ec51c12e2f02f4d
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/17644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This patch makes libpayload enable the instruction cache as the very
first thing, which is similar to how we treat it in coreboot. It also
prevents the icache from being disabled again during mmu_disable() as
part of the two-stage page table setup in post_sysinfo_scan_mmu_setup().
It replaces the existing mmu_disable() implementation with the assembly
version from coreboot which handles certain edge cases better (see
CB:27238 for details).
The SCTLR flag definitions in libpayload seem to have still been
copy&pasted from arm32, so replace with the actual arm64 defintions from
coreboot.
Change-Id: Ifdbec34f0875ecc69fedcbea5c20e943379a3d2d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Puff uses the smbus to access the SPD of memory DIMMs.
It will short the SPD reading time if enabling SPD_READ_BY_WORD.
BUG=b:149360051
BRANCH=None
TEST=build puff and boot up OS
ran cbmem -t | grep FspMemoryInit
Without this patch:
950:calling FspMemoryInit 643,199 (257,588)
With this patch:
950:calling FspMemoryInit 477,714 (154,612)
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Change-Id: I161e8eb386ab604b16746f0deeecc3d6c9063c3a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Fine tune the video timing of panel-BOE_TV101WUM_N53 to avoid noise. The
parameters are based on BOE NV101WUM-N53 preliminary product spec.
BRANCH=kukui
BUG=b:147378025
TEST=bootup pass
Change-Id: Ia9e2cc90f233e87d712c2dc6f4441ca2e5423162
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38401
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The extra data transfer in DSI, namely, lpx, hs_prepare, hs_zero,
hs_exit and the sof/eof of DSI packets, will enlarge the line time,
which causes the real frame on dsi bus to be lower than the one
calculated by video timing. Therefore, hfp_byte is reduced by d_phy to
compensate the increase in time by the extra data transfer. However, if
hfp_byte is not large enough, the hsync period will be increased on DSI
data, leading to display scrolling in firmware screen.
To avoid this situation, this patch changes the DSI Tx driver to reduce
both hfp_byte and hbp_byte, with the amount proportional to hfp and hbp,
respectively. Refer to kernel's change in CL:1915442.
Also rename 'phy_timing' to 'timing' to sync with kernel upstream.
Since the phy timing initialization sequence has been corrected, the m
value adjustment in the analogix driver can be removed.
BUG=b:144824303
BRANCH=kukui
TEST=emerge-jacuzzi coreboot
TEST=Boots and sees firmware screen on krane and juniper
TEST=No scrolling issue on juniper AUO and InnoLux panels
Change-Id: I10a4d8a4fb41c309fa1917cf1cdf19dabed98227
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
When configuring MIPI DSI Tx, the value of pcw was calculated from data
rate in MHz, leading to loss of precision. This patch changes to use
data rate in Hz for the calculation so that the resulting value should
be consistent with the one in kernel (CL:1786327).
In addition, change the type of data rate to u32, and calculation of
data rate from pixel clock is changed to use DIV_ROUND_UP for
consistency with kernel (CL:1761843).
Also remove unused variable txdiv.
BRANCH=kukui
BUG=b:149051882
TEST=emerge-jacuzzi coreboot
TEST=No scrolling issue on Juniper AUO and InnoLux panels
Change-Id: I23220d446833b956431006027bbc8cb20fc696a5
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38827
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Turn on the H1 device in the devicetree. Configure the concerned GPIOs
and enable the required config items.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I37972635454cd0d35608623e7be4110012ace658
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38772
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initial testing of STM support revealed a sizing issue for greater than 4 threads.
This patch reduces the STM smm_save_state_size, which should allow for 24 threads.
Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov>
Change-Id: I025694185469577e072a92ea75cbbb53c24b2c24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38819
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add EC ACPI reporting of current temp and platform critical temp.
Adapted from ACPI dump of ODM AMI firmware.
TEST: check reporting of current/critical temps via lm-sensors
from ACPI on Librem 13v1 and 13v4 boards.
Change-Id: I92641fbbdda46e0c388607a37f7a7cc2dcd6c26d
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This reverts commit a017e5fb3d.
Reason for revert: The extra reset in the FSP after the flex ratio is changed causes recovery reasons to be lost. There are some vboot changes that recently landed that could help with this issue, but for now, we are working on a new AU image for Kohaku and this is causing our automated testing to fail.
Change-Id: Ic38b390842e2a533033587b3247b7c8d982b1dff
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Added CMOS support for MacBook Air 4,2. In future, I hope there will
be more useful options available, because I'm working on macbooks
support.
Also, it may be necessary for hyper_threading support (#29669) once it
will be ready.
Change-Id: I369ed9aeff2098a4840918531be6a34cfc8d2a1e
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Peter Lemenkov <lemenkov@gmail.com>
DMI PCR 2770 (LPC IO DECODE RANGES) should be identical to LPC PCI
offset 0x80. This is specified in PCH BWG par 2.5.1.5.
Add the support to make sure this PCR is always set correctly.
BUG=N/A
TEST=tested on facebook monolith.
Change-Id: I33ff2b96dea78b5ff1c7c9416cf74f67d79f265d
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38746
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With CL:1940398, this option is no longer needed. Recovery
requests are not cleared until kernel verification stage is
reached. If the FSP triggers any reboots, recovery requests
will be preserved. In particular:
- Manual requests will be preserved via recovery switch state,
whose behaviour is modified in CB:38779.
- Other recovery requests will remain in nvdata across reboot.
These functions now only work after verstage has run:
int vboot_check_recovery_request(void)
int vboot_recovery_mode_enabled(void)
int vboot_developer_mode_enabled(void)
BUG=b:124141368, b:35576380
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I52d17a3c6730be5c04c3c0ae020368d11db6ca3c
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38780
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Serves two purposes:
(1) On some platforms, FSP initialization may cause a reboot.
Push clearing the recovery mode switch until after FSP code runs,
so that a manual recovery request (three-finger salute) will
function correctly under this condition.
(2) The recovery mode switch value is needed at BS_WRITE_TABLES
for adding an event to elog. (Previously this was done by
stashing the value in CBMEM_ID_EC_HOSTEVENT.)
BUG=b:124141368, b:35576380
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I30c02787c620b937e5a50a5ed94ac906e3112dad
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Jasper Lake SOC has 8 PCIe root ports. Cleaning up the root ports
as per Jasper Lake. This patch updates the devicetree to enable WLAN
and NVME for jasperlake_rvp and removes the other root port configurations
which are not required.
Change-Id: I6c801d81ccece6b45a7c45212533bb33a6805367
Signed-off-by: Usha P <usha.p@intel.com>
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38679
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ACPI files for xhci in JSL is different from TGL. Hence, renaming
xhci.asl to xhci_tgl.asl and adding a new file xhci_jsl.asl for JSL.
Also, allowing xhci.asl to choose the correct file based on the SoC
selected.
BUG=None
BRANCH=None
TEST=Compilation for JasperLake board is working
Change-Id: Ia8e88e02989ff80d7cd1f28941e005cb0d842fcb
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
SUART3/4 are unused on this board (verified by checking registers on
vendor BMC firmware). Further they break the console for an unknown
reason. Thus disable them.
Change-Id: I30bb8184d03ee1037d9ec33eb1d93ee540563fc5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38818
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These header files need to make use of vb2_shared_data.
Remove the last vestiges of vboot1 data structures in coreboot.
BUG=b:124141368, chromium:1038260
TEST=Build locally with CL:2054269
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I61b27e33751c11aac9f8af261a75d83b003b5f92
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38884
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The body contains a `#` and GNU make 4.3 disagrees with earlier versions
if it should be treated as a comment. Turn it into a `define` which has
clearer semantics regarding comments (interpretation is supposed to be
deferred until the variable is expanded).
Change-Id: I589542abbd14082c3ecc4a2456ebd809fb6911ea
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38793
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Interpretation if # starts a comment inside a variable definition varies
between GNU make versions. Use a wildcard to match the first # and use
`sed` instead of `grep | cut` to avoid unbalanced quoting chars.
Tested with GNU make 4.2.1 and 4.3. Both produce the same output as
4.2.1 did before the patch.
Change-Id: Ib7c4d7323e112968d3f14ea0590b7dabc57c9c45
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
* Add additional information on non-debian cli tools
* Improve spellings and descriptions to the best of my knowledge
Adding info about needed tools in other distribution's package
managers was requested at the coreboot beginner's workshop at 36C3.
Change-Id: Ifff3c8354b4bec9f195f075eb6b2f377195fc237
Signed-off-by: Patrik Tesarik <mail@patrik-tesarik.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
By updating the FSP submodule we now got all FSP headers from within
that repo. This commit changes the default paths to use these and
fixes some include paths to allow the usage of
vendorcode/intel/edk2/UDK2017 together with the official Intel
distribution.
We are also adding back the CHANNEL_PRESENT enum, that is
missing in the official headers.
This was tested on the Razer Blade Stealth (late 2019).
Change-Id: I7d5520dcd30f4a68af325125052e16e867e91ec9
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37579
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christoph Pomaska <github@slrie.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some of the common memory code that was being performed in
mainboard has moved into the soc to reduce redundant code.
This change adapts volteer to use Tiger Lake's new common code.
BUG=b:145642089, b:145238504, b:145564831
BRANCH=none
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
volteer, boot to kernel, "cat /proc/meminfo" and verify it reports
"MemTotal: 8038196 kB".
Change-Id: I32c9b8a040728d44565806eece6cf60b6b6073b6
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The Picasso no longer intends to implement a hybrid romstage,
opting instead for a more traditional bootblock/romstage/ramstage.
Update the documentation to reflect this. Clarify additional
details that have come to light since the last revision.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I6c98c007ddb8a4a05810f19e4215bde719de7bb8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
When acpi_write_dbg2_pci_uart is called and no pci uart is available the
function prints "Device not found" as an error. This is not correct.
Change the error level to BIOS_DEBUG so coreboot reports the device is
not available but doesn't flag this as an error.
BUG=N/A
TEST=build
Change-Id: I14567bcfcf5a6ff427e418d15bc2675ae7a28f53
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch guards CONFIGURABLE_RAMSTAGE symbol (which is default
enable for all x86 systems) with another Kconfig that can be selected
by platform that actually planning to use it.
TEST=CONFIG_CONFIGURABLE_RAMSTAGE is not enabled by default.
Change-Id: I2113445d507294df59fbc7fb1373793b47c6c31c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Part of the design of vboot persistent context is that the workbuf gets
placed in CBMEM and stays there for depthcharge to use in kernel
verification. As such, the space allocated in CBMEM needs to be at least
VB2_KERNEL_WORKBUF_RECOMMENDED_SIZE.
In the VBOOT_STARTS_IN_ROMSTAGE case, prior to this CL, vboot_get_context()
would get invoked for the first time after CBMEM comes up, and it would
only allocate VB2_FIRMWARE_WORKBUF_RECOMMENDED_SIZE.
Initialize the workbuf directly in vboot_setup_cbmem() instead with the
correct VB2_KERNEL_WORKBUF_RECOMMENDED_SIZE.
BUG=b:124141368, chromium:994060
TEST=make clean && make test-abuild
TEST=boot on GOOGLE_EVE with VBOOT_STARTS_IN_ROMSTAGE set
BRANCH=none
Change-Id: Ie09c39f960b3f14f3a64c648eee6ca3f23214d9a
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38778
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If the panel-power sequencer is not configured, libgfxinit falls back
to very conservative defaults (210ms before EDID is probed). This
results in a boot penalty of >100ms (depending on how long it takes
to probe other ports).
Values are taken from the VBTs already checked in. Untested.
Change-Id: I189776ce8684b4c3c01acd6d2fc433ca33a050d5
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
T500 and W500 (Coronado-5) use both digital display connectors. Both
with the DP AUX channel implemented, so add DP2 to the list.
Versions with a discrete GPU don't use external, digital connectors
but seem to have the straps correctly configured. So we hopefully
won't have to handle these specifically.
Based on schematics only, not tested.
Change-Id: I31e1415eff2d5d00c4a231906e3d861d2a59b629
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The first digital display connector is unused, but strapped as if it
were on later revisions. The DP AUX channel of the second connector
is implemented, though, so add DP2 to the list.
Versions with a discrete GPU don't use external, digital connectors
but seem to have the straps correctly configured. So we hopefully
won't have to handle these specifically.
Based on schematics only, not tested.
Change-Id: I7d3e8b3a2123ddc407bb5a0cce86a3634b575f4a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Some board revisions have the straps for display port detection
wrongly configured. So with a single list covering all variants'
possible outputs, we make libgfxinit probe unimplemented ports
which may stall the GMBUS controller and delay the boot for some
hundred milliseconds.
This just copies the list to the various variants with different
display ports, so we can test the actual changes individually.
Change-Id: I48cdea1d71d9553b6bdbce432eae986996329239
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The attempt to install pfSense on hard disk on PC Engines apu2 board
ended up in a SATA driver error. The problem is related only to BSD
and didn't occur with Linux kernel. Changing SATA mode from IDE to
AHCI solved the problem.
Additionally AHCI is faster than IDE so it speeds up the installation.
Since AHCI works perfectly with SeaBIOS, Linux and BSD, make it a default
choice for all Hudson southbridges.
Change-Id: I1b0322392712d797dd5a8931150c8d0ff1b60940
Signed-off-by: Piotr Kleinschmidt <piotr.kleins@gmail.com>
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35891
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update the create_coreboot_variant.sh and kconfig.py to support the
zork baseboard. Full template files will be added in a later CL.
BUG=b:148161697, b:148281637
BRANCH=None
TEST=`./create_coreboot_variant.sh zork dalboz` and verify that the
changes staged are correct.
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: Ie0a29bb9f4bb8f3bb7eaeae8799cef861c395e7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Move some of the common memory code that was being performed in
mainboard into the soc to reduce redundant code going forward.
BUG=b:145642089
BRANCH=none
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
volteer, log into kernel and verify memory size shows 8GB.
Change-Id: I8de502d4f05d52b9dae34e3b013c6d5b1886fa55
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable the dGPU on the Lenovo T440P. It uses the same code (roughly) of
the T430S. By default, it is set to be disabled however it can be
enabled via the nvram option enable_dual_graphics. Removed hybrid graphics
options too as they are not valid for the T440p. Tested on a T440P with
Ubuntu 18.04.4 with Kernel 5.3.0-29 (successful). Tested on same machine
with Windows 10 1909 (machine check exception bluescreen).
Change-Id: Idf8c2c0d1ae34bda8736448d3e350396e3cf7a93
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38723
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Since most of Bloog series SKUs need to disable DRRS support.
If Bloog and Unprovisioned SKUs then return vbt.bin to enable DRRS support,
return vbt_blooguard.bin for other SKUs to disable DRRS support.
Bipship follow blooguard to disable DRRS support.
BUG=b:148892903, b:147021309
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage
check i915_drrs_status shows DRRS supported NO when SKU ID is bipship.
Change-Id: I61f12d4ddea17a05255751fde2a5ce822dd2e782
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add the capability to update the Flash Descriptor directly instead
of raising a Segmentation Fault. In this way it will be possible to
add a Kconfig options to modify the ifd descriptor at build-time.
Change-Id: Id3db09291af2bd2e759c283e316afd5da1fb4ca7
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Below changes have been implemented in send_heci_reset_req_message():
1. Modify return values to align with other functions in the same file.
2. Add additional logging.
3. Replace macro definitions of reset types with ENUM.
4. Make changes to caller functions to sync with new return values.
5. Rename send_heci_reset_req_message() to cse_request_global_reset().
Test=Verified on hatch board.
Change-Id: I979b169a5bb3a5d4028ef030bcef2b8eeffe86e3
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37584
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Below changes are implemented:
1. Fix typos.
2. Rename 'padding' field of hmrfpo_get_status_resp struct to
'reserved' to match with ME BWG Guide.
3. Add documentation for HMRFPO Status.
TEST=Build and boot hatch
Change-Id: I4db9bdf7386c48e17ed0373cf334ccff358d1951
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Below changes are implemented:
1. Move HFSTS1 register definition to SoC since HFSTS1 register definition
is specific to a SoC. Moving structure back to SoC specific to avoid
unnecessay SoC specific macros in the common code.
2. Define a set of APIs in common code since CSE operation modes and
working states are same across SoCs.
cse_is_hfs1_com_normal(void)
cse_is_hfs1_com_secover_mei_msg(void)
cse_is_hfs1_com_soft_temp_disable(void)
cse_is_hfs1_cws_normal(void)
3. Modify existing code to use callbacks to get data of me_hfs1 structure.
TEST=Build and Boot hatch, soraka, tglrvp, bobba and iclrvp boards.
Change-Id: If7ea6043d7b5473d0c16e83d7b2d4b620c125652
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This CL has changes that allow us to enable a configurable
ramstage, and one change that allows us to minimize PCI
scanning. Minimal scanning is a frequently requested feature.
To enable it, we add two new variables to src/Kconfig
CONFIGURABLE_RAMSTAGE
is the overall variable controlling other options for minimizing the
ramstage.
MINIMAL_PCI_SCANNING is how we indicate we wish to enable minimal
PCI scanning.
Some devices must be scanned in all cases, such as 0:0.0.
To indicate which devices we must scan, we add a new mandatory
keyword to sconfig
It is used in place of on, off, or hidden, and indicates
a device is enabled and mandatory. Mandatory
devices are always scanned. When MINIMAL_PCI_SCANNING is enabled,
ONLY mandatory devices are scanned.
We further add support in src/device/pci_device.c to manage
both MINIMAL_PCI_SCANNING and mandatory devices.
Finally, to show how this works in practice, we add mandatory
keywords to 3 devices on the qemu-q35.
TEST=
1. This is tested and working on the qemu-q35 target.
2. On CML-Hatch
Before CL:
Total Boot time: ~685ms
After CL:
Total Boot time: ~615ms
Change-Id: I2073d9f8e9297c2b02530821ebb634ea2a5c758e
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Update the QUP DFSR cmd to clear the SW control and also update the perf
registers when M is set. While at it also update the d_2 values.
Tested: validated DFSR clock configuration and M/N/D values.
Change-Id: I6bba1c6f99810963aaa607885ef400c523c0e905
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Enabling an assertion in vb2_member_of() results in coreboot
linking vb2ex_abort() and vb2ex_printf() in ramstage.
Move these two functions from vboot_logic.c to vboot_lib.c,
which is should be enabled in all stages if CONFIG_VBOOT_LIB
is enabled. Note that CONFIG_VBOOT_LIB is implied by
CONFIG_VBOOT.
Relevant vboot_reference commit: CL:2037263.
BUG=b:124141368, chromium:1005700
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ica0103c5684b3d50ba7dc1b4c39559cb192efa81
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Wait for HPD DP unless HDMI is plugged.
Some Type-C monitors do not immediately assert HPD. If we continue
to boot without HPD asserted, Depthcharge fails to show pictures
on a monitor even if HPD is asserted later.
Similar to that of b:72387533 however our DP&HDMI are beind a MST.
See commit d182b63347 on how this was done for mainboard/fizz.
BUG=b:147992492
BRANCH=none
TEST=Verify firmware screen is displayed even when a type-c monitor
does not immediately assert HPD. Verify if HDMI monitor is connected,
AP does not wait (and firmware screen is displayed on HDMI monitor).
Change-Id: I19d40056e58f1737f87fd07d62b07a723a63d610
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
The type of dev in the PCI_FUNC(dev) is incorrect. Fix it using
PCI_DEV2DEVFN() macro. Tested on a T440P, and necessary on this board
to enable the dGPU.
Change-Id: I3fb0f677cc98800f355f6af7d3172be3e59ce5c2
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38722
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PC Engines apu2 platform uses AGESA 1.0.0.4, because upstream AGESA
1.0.0.A doesn't work on apu2 - the platform doesn't boot. To properly
utilize AGESA 1.0.0.4 we need to adjust AGESA header to state, which
is compatible with AGESA 1.0.0.4 version.
Cut out the changes introduced in CB:11225 exclusively for apu2 board.
TEST=boot PC Engines apu2 and launch Debian Linux
Change-Id: I3d85ee14e35dae8079e8d552b6530a3867f65876
Signed-off-by: Piotr Kleinschmidt <piotr.kleins@gmail.com>
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This update is a combination of all four of the patches so that the
commit can be done without breaking parts of coreboot. This possible
breakage is because of the cross-dependencies between the original
separate patches would cause failure because of data structure changes.
security/intel/stm
This directory contains the functions that check and move the STM to the
MSEG, create its page tables, and create the BIOS resource list.
The STM page tables is a six page region located in the MSEG and are
pointed to by the CR3 Offset field in the MSEG header. The initial
page tables will identity map all memory between 0-4G. The STM starts
in IA32e mode, which requires page tables to exist at startup.
The BIOS resource list defines the resources that the SMI Handler is
allowed to access. This includes the SMM memory area where the SMI
handler resides and other resources such as I/O devices. The STM uses
the BIOS resource list to restrict the SMI handler's accesses.
The BIOS resource list is currently located in the same area as the
SMI handler. This location is shown in the comment section before
smm_load_module in smm_module_loader.c
Note: The files within security/intel/stm come directly from their
Tianocore counterparts. Unnecessary code has been removed and the
remaining code has been converted to meet coreboot coding requirements.
For more information see:
SMI Transfer Monitor (STM) User Guide, Intel Corp.,
August 2015, Rev 1.0, can be found at firmware.intel.com
include/cpu/x86:
Addtions to include/cpu/x86 for STM support.
cpu/x86:
STM Set up - The STM needs to be loaded into the MSEG during BIOS
initialization and the SMM Monitor Control MSR be set to indicate
that an STM is in the system.
cpu/x86/smm:
SMI module loader modifications needed to set up the
SMM descriptors used by the STM during its initialization
Change-Id: If4adcd92c341162630ce1ec357ffcf8a135785ec
Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: ron minnich <rminnich@gmail.com>
We set MPS to speed_to_default_mps(speed) initially
but later compare maxpacketsize with 8 to change mps.
So compare with speed_to_default_mps(speed) to determine
if we need to change settings here.
BUG=b:147783572
BRANCH=none
TEST=works with 12Mbps/8MPS USB device
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I32455483fceec56f14af6118b77615c14b3f9f39
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38556
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TGL FSP does pin mux for ISH related to pins by UPD(PchIshSpiEnable,
PchIshUartEnable, PchIshI2cEnable, PchIshGpEnable) but as default UPD
value is disabled, FSP doesn't do pin mux. So pin mux for ISH in gpio.c.
Pin mux for ISH for TGLRVP
ISHUART0: GPP_D13, GPP_D14 as NF1
ISHI2C0: GPP_B5, GPP_B6 as NF1
ISHGPIO0-7: GPP_D0~D3, GPP_D17~D18, GPP_E15~E16 as NF1
BUG=none
BRANCH=none
TEST=Build and boot to OS and check pinctl driver to check pin mux.
Check ISHUART0, ISHI2C0, ISHGPIO0-7 native function setting.
They should be NF1.
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I1a9ba3a713527f5ce962659960418cd0f37dd262
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This change adds support for allocating resources for PCI express hotplug
bridges when PCIEXP_HOTPLUG is selected. By default, this will add 32 PCI
subordinate numbers (buses), 256 MiB of prefetchable memory, 8 MiB of
non-prefetchable memory, and 8 KiB of I/O space to any device with the
PCI_EXP_SLTCAP_HPC bit set in the PCI_EXP_SLTCAP register, which
indicates hot-plugging capability. The resource allocation is configurable,
please see the PCIEXP_HOTPLUG_* variables in src/device/Kconfig.
In order to support the allocation of hotplugged PCI buses, a new field
is added to struct device called hotplug_buses. This is defaulted to
zero, but when set, it adds the hotplug_buses value to the subordinate
value of the PCI bridge. This allows devices to be plugged in and
unplugged after boot.
This code was tested on the System76 Darter Pro (darp6). Before this
change, there are not enough resources allocated to the Thunderbolt
PCI bridge to allow plugging in new devices after boot. This can be
worked around in the Linux kernel by passing a boot param such as:
pci=assign-busses,hpbussize=32,realloc
This change makes it possible to use Thunderbolt hotplugging without
kernel parameters, and attempts to match closely what our motherboard
manufacturer's firmware does by default.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I500191626584b83e6a8ae38417fd324b5e803afc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35946
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The eltan verified_boot is using the vboot 2.1 data structures and code,
as well as the fwlib21 build target, they are all deprecated. Refer to
CB:37654 for more information.
The verified_boot code is updated to use the vb2 structures and code and
make sure only public functions are used.
BUG=N/A
TEST=build
Change-Id: I1e1a7bce6110fe35221a4d7a47c1eb7c7074c318
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Originally a part of security/intel/stm.
Add get_pmbase to the intel platform setup code.
get_pmbase is used by the coreboot STM setup functions to ensure
that the pmbase is accessable by the SMI handler during runtime.
The pmbase has to be accounted for in the BIOS resource list so
that the SMI handler is allowed this access.
Change-Id: If6f6295c5eba9eb20e57ab56e7f965c8879e93d2
Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37990
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch removes duplicate CPUID entry between KBL and CFL.
CFL-D0 has KBL CPU + CNP PCH hence no need to redefine same KBL
CPUID (0x806EA) for CFL-D0.
TEST=CFL-D0 report platform serial msg shows "Cofeelake D0" with
CPUID 0x806EA.
Change-Id: I078dd7860891896b512967dc8dec5dd94d069193
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
The current MP init timeout is hardcoded as 1s. To support
platform with many cpus, the timeout needs to be adjusted.
The number of cpus is calculated as:
number of sockets * number of cores per socket *
number of threads per core
How long the timeout should be set to, is heuristic.
It needs to be set long enough to ensure reboot stability,
but not unreasonable so that real failures can be detected
soon enough, especially for smaller systems.
This patch sets timeout to be minimum as 1 second, while each
cpu adds 0.1 second.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Change-Id: Ibc079fc6aa8641d4ac8d8e726899b6c8d055052e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Set HeciEnabled = 1 on puff device tree to turn on
Intel ME communication interface.
BUG=b:143232330
BRANCH=None
TEST=Build puff and boot up OS.
ran lspci and confirmed there is a HECI device.
00:16.0 Communication controller: Intel Corporation Device 02e0
Change-Id: I2debb885022ae31e395869d014a91824b5dd980c
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Updating from commit id 6ef33b99:
2019-11-22 Hung-Te Lin futility: updater: refactor: unify
getting temp files for firmware images
to commit id 0e97e25e:
2020-01-23 Julius Werner 2lib: Fix struct vb2_hash the way it was
meant to be
Change-Id: I539aba2f283804f67ff3ff4f98324b3d10b2bb54
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38604
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
According to the C standard, accessing the NULL pointer (memory at
address zero) is undefined behaviour, and so GCC is allowed to optimize
it out. Of course, accessing this memory location is sometimes
necessary, so this optimization can be disabled using
-fno-delete-null-pointer-checks. This is already done in coreboot, but
adding it to xcompile will also disable it for all the payloads. For
example, coreinfo compiled with LTO libpayload crashes when this flag
isn't set, presumably because the compiler is optimizing something out
that it shouldn't.
Change-Id: I4492277f02418ade3fe7a75304e8e0611f49ef36
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38289
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
acpi_device_scope() will return NULL if it is unable to find the path
of the parent device. Return early if this is the case to prevent a null
pointer dereference.
Change-Id: I3eff1c1e3477c75c7130b52898de7d59692ba412
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1409672
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38669
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It is found that keyboard backlight in T440p is enabled by clearing
bit 3 of EC RAM 0x01. This patch sets has_keyboard_backlight in
devicetree.cb and also corrects the CMOS configuration.
Change-Id: Ib4c2b1591d26e2bb33f9549e3933efe9a6e0b043
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Dennis Witzig <dennis@wtzg.de>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Asserting reset in RO instead of in RW has no impact on security or
performance, but it does limit improvements to this process later.
This fix removes reset line control from RO and makes these variants
consistent with other hatch variants.
This fix reinforces the concept from commit fcd8c9e99e
(hatch: Fix FPMCU pwr/rst gpio handling).
BUG=b:148457345
TEST=None
Change-Id: I12dc0c3bead7672e2d3207771212efb0d246973a
Signed-off-by: Craig Hesling <hesling@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This GPIO dumping was implemented using the
Document Number: 341080-001
Intel® 495 Series Chipset Family On-Package Platform Controller Hub
Volume 1 of 2
datasheet. The GPIO community ports can be found in table 36-1, while
the community and pin descriptions are taken from
linux/pinctrl/intel/pinctrl-icelake.c .
This commit was tested on the late 2019 Razer Blade Stealth with 1065G7
and Chipset 495 PCH and the output manually compared against
linux/pinctrl-intel.
Change-Id: Ib40f1dbae57169678e92ea9ad0df60ff91b5b22c
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Newest clang compilers warn about "misleading indentation", and because
warnings-are-errors in our builds, that breaks the build.
The lzma code base is vendored in, so we might just have to update it,
but that's a bigger effort than just removing a couple of spaces (the
coding style of the file is horrible, but I will only change it as much
as the compilers ask for).
BUG=chromium:1039526
Change-Id: I6b9d7a760380081af996ea5412d7e3e688048bfd
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Remove EC_HOST_EVENT_MKBP from kohaku's EC_SCI_EVENTS mask, so that
MKBP events don't generate an SCI. The EC is also being changed to use
host events to wake up the system, and use the EC_INT_L line for MKBP
IRQ signalling. Otherwise, there would be two IRQs generated for MKBP
events.
BUG=b:144122000
BRANCH=firmware-hatch-12672.B
TEST=System shows ACPI interrupt as the wakeup IRQ, and the
MKBP host event is properly processed as well.
Change-Id: I9ff964e38e66ccb953a1adad5a936a9da6e4f3a1
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38654
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add new functions to get (from the EC):
1) The number of USB-PD ports
2) The capabilities of each port (EC_CMD_GET_PD_PORT_CAPS)
BUG=b:146506369
BRANCH=none
TEST=Instrumented calls to these and verified the data
Change-Id: I57edbe1592cd28b005f01679ef8a8b5de3e1f586
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The new host command provides these static capabilities of each USB-PD port:
1) Port number
2) Power role: source, sink, dual
3) Try-power role: none, sink, source
4) Data role: dfp, ufp, dual
5) Port location: these come from power_manager
BUG=b:146506369
BRANCH=none
TEST=compiles
Change-Id: I923e4b637a2f41ce173d378ba5030f1ae8c22222
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The help output suggests clean-docker should be used to remove the
docker coreboot containers and images. The Makefile actually supports
the docker-clean target.
Corrected the help output to reflect the actual Makefile target.
BUG=N/A
TEST=build
Change-Id: Ib24f8e1ecdf3bdc31b3f8b484ce7ca0c19b645ee
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
This patch overrides CPU flex ratio on hatch in order to get
better boot time numbers in vboot_reference.
BUG=b:142264107
TEST=Able to save ~100ms of platform boot time while running with
lower cpu flex ratio (i.e. freq ~1500MHz)
Without this CL
1100:finished vboot kernel verification 802,443 (148,108)
With this CL
1100:finished vboot kernel verification 685,382 (46,496)
Change-Id: Idd1d1c0c04b1f742f17227a1335f27a956ee940d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36865
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In glibc feature control macros, _DEFAULT_SOURCE is the shorthand to
tell glibc to enable "all the default stuff", meaning POSIX, BSD and
System V interfaces. However, this macro is somewhat recent and older
glibc versions (e.g. 2.12) are still occasionally in use that don't
recognize it yet. For the benefits of users with these versions, let's
also enable the deprecated _BSD_SOURCE and _SVID_SOURCE macros which
essentially achieve the same thing. We must continue to define
_DEFAULT_SOURCE so that newer glibc versions don't throw a deprecation
warning.
This patch should make BSD-style byteswap macros like le32toh()
available on these older glibc versions.
Change-Id: I019bbcf738a1bcdccd7b299bdde29cd4d4ded134
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Looks like selecting SOC_INTEL_COMMON force-sets MMCONF_BASE_ADDR to
some value which can't be overriden outside of soc/intel/common. So
adding a non-SoC platform thats uses code from soc/intel/common is not
possible.
TEST=build test on wip platform
Change-Id: Ia160444e8ac7cac55153f659f4d98f4f77f0d467
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: David Guckian
Update the security document to reflect the current state of the
coreboot implementation.
Add more detail and document the change to the public vboot API.
BUG=N/A
TEST=build
Change-Id: I228d0faae0efde70039680a981fea9a436d2384f
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38591
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
commit 1191c09201b43aab55333a70d056d0c355abe329 at
https://salsa.debian.org/agx/lintian/tree/master/data/spelling provides
a much more comprehensive collection of misspellings, so merge it in.
While at it, also sort the file for future easier merging which is the
main reason that some lines appear to be removed: they're merely moved.
For sorting, I adapted their make rule:
make -f - sort-spelling.txt <<'EOF'
.RECIPEPREFIX=%
sort-%: %
%csplit --prefix $<- $< '/^$$/'
%LC_ALL=en_US sort -u $<-01 | cat $<-00 - > $<
%rm -f $<-0[01]
EOF
Change-Id: I939e3a8820c88d0e639bd29b46a86b72bce1a098
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38632
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Turns out when going into S0ix we want the kernel to toggle de-assert to 0 for
the ISOLATE# pin on the NIC for S0ix not to be woken by PCIe traffic on PCH.
Upon resume the ISOLATE# pin on the NIC is then re-asserted for it to become
lively again.
BUG=b:147026979
BRANCH=none
TEST=Boot puff and do 1500 cycles of S0ix.
Change-Id: I3470e1edd93b461b66fc6444541a64339bcdcce3
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38523
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Turns out when going into S0ix we want the kernel to toggle de-assert to 0 for
the ISOLATE# pin on the NIC for S0ix not to be woken by PCIe traffic on PCH.
Upon resume the ISOLATE# pin on the NIC is then re-asserted for it to become
lively again.
V.2: Ensure reset_gpio && enable_gpio are optional.
BUG=b:147026979
BRANCH=none
TEST=Boot puff and do 100 cycles of S0ix.
Change-Id: I3ae8dc30f45f55eec23f45e7b5fbc67a4542f87d
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Allow for making both reset_gpio && enable_gpio as optional in
the params by fixing a potential NULL deref and defaulting to
zero values.
BUG=b:147026979
BRANCH=none
TEST=builds
Change-Id: I8053d7a080dfed898400c0994bcea492c826fe3d
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds CMP-H LPC IDs.
TEST=Build an image and boot with discrete TPM chip.
Enable measured boot and kernel could get the measured
data from TPM chip.
Change-Id: I7eac8b0514f79b47a05973210e2472dd1dc3d0ed
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38251
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The fwts method test reports errors on the methods implementing
processor throttling control. The T states are not supported in coreboot
at this moment.
Remove the methods required by processor throttling control. They can be
restored when the required support has been added to the SoC
implementation.
BUG=https://ticket.coreboot.org/issues/252
TEST=tested using fwts on facebook monolith.
Found-by: fwts 19.12.00
Change-Id: Ib50607f60cdb2ad03e613d18b40f56a4c4a4c714
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
TGL FSP does just pin mux for image clock pins by UPD and image clocks
are controlled by ACPI(camera_clock_ctl.asl) under tigerlake SOC folder.
Disable image clocks by UPD for bypassing FSP pin mux and do pin mux
in gpio.c according to board design.
BUG=none
BRANCH=none
TEST=Build and boot to OS
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I5aba5b2fb6deee231e3ec34c8dbc9972b01041f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38562
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
pin mux for IMGCLKOUT_0 and IMGCLKOUT_1
BUG=none
BRANCH=none
TEST=Build and boot to OS and check pinctl driver to check pin mux for
Image clocks pins(GPP_D4, GPP_H20)
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ifb0c2b17dd481ef6c19bdf9ee84f47ef08d7b9a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
With UART3 and 4 enabled, the serial console in LinuxBoot crashes. This
is a short-term solution until we found and fixed the original bug.
Change-Id: I75cb387ef12944232b51f6d8d41810bb27754b05
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Add helper functions to get board's sku_id and fw_config. Enable
EC_GOOGLE_CHROMEEC_BOARDID to get board_id. Add board's SKU ID and
OEM name into SMBIOS table.
BUG=b:144768001
TEST=Build Test.
Change-Id: Id1729e245accf5acc29307a22721362fb1ce0878
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38551
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The names of each spi flash cause quite a bit of bloat in the text
size of each stage/program. Remove the name entirely from spi flash
in order to reduce overhead. In order to pack space as closely as
possible the previous 32-bit id and mask were split into 2 16-bit
ids and masks.
On Chrome OS build of Aleena there's a savings of >2.21KiB in each
of verstage, romstage, and ramstage.
Change-Id: Ie98f7e1c7d116c5d7b4bf78605f62fee89dee0a5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch creates a new commonlib/bsd subdirectory with a similar
purpose to the existing commonlib, with the difference that all files
under this subdirectory shall be licensed under the BSD-3-Clause license
(or compatible permissive license). The goal is to allow more code to be
shared with libpayload in the future.
Initially, I'm going to move a few files there that have already been
BSD-licensed in the existing commonlib. I am also exracting most
contents of the often-needed <commonlib/helpers.h> as long as they have
either been written by me (and are hereby relicensed) or have an
existing equivalent in BSD-licensed libpayload code. I am also
relicensing <commonlib/compression.h> (written by me) and
<commonlib/compiler.h> (same stuff exists in libpayload).
Finally, I am extracting the cb_err error code definitions from
<types.h> into a new BSD-licensed header so that future commonlib/bsd
code can build upon a common set of error values. I am making the
assumption here that the enum constants and the half-sentence fragments
of documentation next to them by themselves do not meet the threshold of
copyrightability.
Change-Id: I316cea70930f131e8e93d4218542ddb5ae4b63a2
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The GLK bootblock seems(?) to be hard limited to 32KB and some Octopus
variants are so close to that that they only have 0.5KB left. This is
blocking development of new core features, so let's disable the
bootblock console to gain a couple of KB back (like we already did on
RK3288).
There are probably other opporunities for code size reduction here (e.g.
it seems that almost half(!) of that whole bootblock size is taken up by
devicetree.cb structures), but I'm not familiar enough with the platform
to dig into them.
Change-Id: I05b4ecf5abef7307e3d0a81db04a745ff3da0c42
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38521
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All variants of ga-b75m-d3h lack ACPI definitions for legacy PCI
slots, which causes IRQ issue if it gets legacy PCI card installed.
The missing definitions (mainly Interrupt Routing Table) are added to
fix that.
NOTE: The added definitions are actually for ga-b75-d3v, but since
they form superset of definitions needed by ga-b75m-d3{h,v}, they can
be applied to all three existing variants with suitable preprocessor
instructions.
Change-Id: Id79c759a5fadb38c2873edc07293cbb14401ac9a
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The System76 Lemur Pro (lemp9) is an upcoming laptop computer. Support
in coreboot is developed by System76 and provided as the default
firmware option. Testing is done on a pre-production model expected to
be identical from a firmware perspective to the production model.
Working:
- Payload
- Tianocore
- CPU
- Intel i7-10510U
- Intel i5-10210U
- EC
- ITE IT5570E running https://github.com/system76/ec
- Backlit Keyboard, with standard PS/2 keycodes and SCI hotkeys
- Battery
- Charger, using AC adapter or USB-C PD
- Suspend/resume
- Touchpad
- GPU
- Intel UHD Graphics 620
- GOP driver is recommended, VBT is provided
- eDP 14-inch 1920x1080 LCD
- HDMI video
- USB-C DisplayPort video
- Memory
- Channel 0: 8-GB on-board DDR4 Samsung K4AAG165WA-BCTD
- Channel 1: 8-GB/16-GB/32-GB DDR4 SO-DIMM
- Networking
- M.2 PCIe/CNVi WiFi/Bluetooth
- Sound
- Realtek ALC293D
- Internal speaker
- Internal microphone
- Combined headphone/microphone 3.5-mm jack
- HDMI audio
- USB-C DisplayPort audio
- Storage
- M.2 PCIe/SATA SSD-1
- M.2 PCIe/SATA SSD-2
- RTS5227S MicroSD card reader
- USB
- 1280x720 CCD camera
- USB 3.1 Gen 2 Type-C (left)
- USB 3.1 Gen 2 Type-A (left)
- USB 3.1 Gen 1 Type-A (right)
Not working:
- TPM2 - SPI bus 0, chip select 2 is used. Chip selects other than 0
are not currently supported by the intel fast_spi driver.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ib0a32bbc6f89a662085ab4a254676bc1fad7dc60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Under some circumstances grep detects the input of a spd hex file
as binary resulting in an spd source not beeing added to the
resulting spd.bin. This appears to be especially the case with
heavily commented files.
This commit forces grep to read the input as text file.
Example SPD that would else be detected as binary (regardless
of stripped zero blocks).
```hex
\# TotalBytes: 512 ; BytesUsed: 384
23
\# SPD Revision 1.1
11
\# DDR Ramtype: LPDDR4X
11
\# Config Rest
0E 16 21 95 08 00 00 00 00 0A 22 00 00 49 00 04
0F 92 54 05 00 84 00 90 A8 90 C0 08 60 04 00 00
[...]
\# CRC Is: 0x1EB4 Calculated: 0x1EB4 Match!
1E B4
\# ModuleSpecificParameter
[...]
\# HybridMemoryParameter
[...]
\# ExtendedFunctionParameter
[...]
\# ManufactoringInformation
\## Module Manufactoring ID
00 00
\## Module Manufactoring Location and Date
00 00 00
\## Module Manufactoring Serial
00 00 00 00
\## Module Manufactoring Part Number: "K4UBE3D4AA-MGCL"
4B 34 55 42 45 33 44 34 41 41 2D 4D 47 43 4C 00
00 00 00 00
\## Module Manufactoring Revision Code
00
\## Module Manufactor: "Samsung" (0xCE80)
CE 80
\## Module Stepping
00
\## Module Manufactoring Data
[..]
\## Module Reserved
00 00
\# EndUserProgrammable
[...]
```
Thanks to Patrick Georgi for checking that this grep option
is widely available.
Change-Id: I7e5bad069531630b36dc3702c8c4bd94ba0946c1
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38426
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop DRAMT write as it's only rewriting the power on default.
PMCR write is required. Update comment on its purpose and move to
end of sdram_enable().
Change-Id: I62e8b2531f0f297ffb7db440db89ffa65771b7d5
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
As per PC client TPM specification, the TPM description contains the
base address of the TIS interface 0xfed40000 and the size of
the MMIO area is 20KB (0x5000). Hence ACPI used to reserve those fixed
system memory from getting used by OS.
Platform with TPM_CR50 doesn't require fixed SoC mapped memory hence
additional reservation might not required.
TEST=Build and boot EVE and Soraka to OS.
Change-Id: Id02a2659ce42f705180370000df89d4f6b64afce
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38512
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Optane memory module shows up as 2 NVMe devices in x2 config - NVMe storage
device and NVMe Optane memory. Storage device uses rp9 and optane memory
uses rp11. This patch enables rp11. Please note that these two share clk pins.
This is also dependent on pciecontroller3 config to be set as 2x2 instead of
1x4 in fit configuration in IFWI.
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board from Optane and check 2 NVMe devices
from lspci
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ic81244bebac78102af7ba6308ab64b18c886f839
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
GPIOs are divided into different communities. Each community
consists of one or more GPIO groups. We need to configure the
groups in coreboot so that they are mapped properly.
GPIO comuinities in coreboot should match with the kernel gpio
communities also. Kernel reads the ASL file from coreboot. This
patch adds the proper community mapping in ASL code to match with
kernel code. In gpio_soc_defs.c file we are indexing the groups
correctly. In gpio.h file we define all the gpio devices as kernel
populates sysfs with separate gpio device for each community. This
patch is created based on Intel Tiger Lake Processor PCH Datasheet
with Document number:575857 and Chapter number:27.
BUG=b:144680462
BRANCH=none
TEST=Build and boot tigerlake rvp board. In /sys/kernel/debug/pinctrl
verify INTC34C5:0<1-3> listing all the pins for each community.
e.g., #cat /sys/kernel/debug/pinctrl/INT34C5:00/pins should list
all the community 0 pins.
Change-Id: I40c386db060d84c1b7fba9c587f960d6a92f84ba
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Having a working board reset is certainly better when you're running
vboot (because otherwise you'll hang when transitioning into recovery
mode), but I don't think it should be strictly required, since it's
still somewhat usable without. This is particularly important for
certain test platforms that don't have a good way to reset but might
still be useful for vboot testing/prototyping.
Change-Id: Ia765f54b6e2e176e2d54478fb1e0839d8cab9849
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38417
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates system agent related registers bit definitions
as per EDS.
For example:
As per CNL/ICL EDS MCHBAR register base is between bit 16-38
but coreboot programming was not aligned with EDS previously.
CNL EDS doc number: 566216
Also provide provision to program 64bit values as per SA EDS definitions
TEST=Dump MCHBAR in coreboot and ASL shows same 32 bit value.
Change-Id: I37340408fe89c94ce81953c751c8d7e22bc81a42
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
1. Add a TEMP_SENSOR3
2. Update DFPS (fan performance state) table with values received
from thermal team
3. Update PL1 override to 15W
4. Update PL2 override to 51W
BRANCH=hatch
BUG=b:147792204
TEST=build and verify by thermal team
Change-Id: I21c17c09a097c963f4dd1b7d5f8212c83a639dc3
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38025
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id 2843aa62:
2019-12-12 Julius Werner 2lib: Move firmware body size reporting to
separate function
to commit id f5367d59:
2020-01-20 Joel Kitching vboot: translate recovery reason info from
vboot 2->1
This brings in 27 new commits.
Change-Id: I7d33337881fa2d36d6e562b0a390b56227cfad55
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
This CL allows MKBP events from the EC to wake the system from suspend
states.
BUG=b:144122000
BRANCH=firmware-hatch-12672.B
TEST=Verify that MKBP events generated from EC will wake the system
from S0ix.
Change-Id: I8a0d2c7ed89fa1ea937a08c3082cc5d3e782efff
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The firmware configuration (fw_config) field is store in the CBI EEPROM
and it should be used to make firmware customization instead of
sku/variant id.
BUG=b:145519081
TEST=builds
Change-Id: I790998a29e724ecdff8876cca072267537b7cea6
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
GPIOs are divided into different communities. Each community
consists of one or more GPIO groups. We need to configure the
groups from coreboot so that they are mapped properly.
GPIO communities should be properly configured in GPIO_CFG and
MISCCFG registers. GPP_* defines in gpio_soc_defs.h are configured
in GPIO_CFG register while the PMC_GPP_* in pmc.h are used to
configure the MISCCFG registers.
BUG=b:144680462
BRANCH=none
TEST=Build and boot tigerlake rvp board. Verified that after
setting the gpe from devicetree the GPP_EN register for
that community gets updated setting that specific bit.
From the iotools i checked that GPE_EN register for that
community is updated with that specific bit set to 1.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I585100375feee39b5a9105bdf6d9f5ca3a5bb2fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
The monolith board doesn't support the S3 and S4 states because of the
watchdog and failover mechanisms.
Remove S3 and S4 from the available sleepstates.
BUG=N/A
TEST=build
Change-Id: I01f67d8bb3f9e45caef748caca91eeb6859d7393
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Some boards don't support S3 or S4. The S4 state can't be removed from
the available sleep states.
Add a config item that allows removal of the S4 state from the list of
available sleep states. The S4 state can be removed by selecting the
item on board level.
For the AMD chipsets the SSFG mask is updated to remove the S4 state.
BUG=N/A
TEST=build
Change-Id: Id802c4cc40308ddf39e99e7f226d55e0e020f0c9
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38431
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to VRTT report, add ac/dc loadline configuations in puff device
tree.
BUG=b:147206535
BRANCH=None
TEST=build coreboot and fsp with enabled fw_debug.
Flashed to puff and checked the log.
All ac/dc loadline configs were set correctly.
Change-Id: Ia806de23a1fefcaac3ce9a462a8a04eee5eabcae
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Only the ACPI code needs to be extended, as smihandler.c already
supported it. The _Q50 Method is just _Q18 with changed name.
On Linux, pressing the undock button does nothing, so the only safe
way to undock is to press Fn+F9. With this patch, when the undock
button is pressed, the green LED lights up, and undocking is safe.
Change-Id: Iaaecad031bb1f39dd1a778d0c8eaea6bce9e0f57
Signed-off-by: Maciej Matuszczyk <maccraft123mc@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38446
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Mimoja <coreboot@mimoja.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The mainboard ASL code contained a power button definition. This is not
required as the system uses the standard ACPI power button.
Remove the PWRB device from ASL.
BUG=N/A
TEST=tested using fwts on a facebook monolith.
Found-by: fwts 19.12.00
Change-Id: I25a842539ee2e8febc8a1ae88843a71ccb4ee68e
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38133
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When regions are resized they are always aligned to the top of the
region. For the BIOS region this is correct. The other regions however
should be aligned to the bottom of the region.
Update the region handling to only align BIOS region to top of region.
BUG=N/A
TEST=verified image resize
Change-Id: Ied0e763b5335f5f124fc00de38e5db1a4d0f6785
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38460
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
NOTE: The ME interface was disabled on folio_9470m and revolve_810_g1.
It is assumed that they were ported while the ME was in an abnormal
state (usually due to me_cleaner usage), and that it should be enabled.
In any case, the MEI device is hidden if the ME fails to boot already.
Change-Id: Ibf32a034653946f49f72a2c19c41a4033964ef83
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Update Makefile.inc so as to add the SPD data when needed. Tested
building other variants, no spd.bin gets added because they don't select
GENERIC_SPD_BIN.
Tested with BUILD_TIMELESS=1, binary does not change.
Change-Id: I0cda3f839baa227ce6a4b8f0510934125e5afb59
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Since this board does not have integrated graphics, do not install the
INT15 handler if it is not selected in Kconfig.
NOTE: Since cmos options are not very flexible, this board ends up with
a spurious gfx_uma_size option. Other than that, everything is the same.
Tested with BUILD_TIMELESS=1, binary does not change when ignoring the
cmos options.
Change-Id: I2ebcfd5160773bf98a3d23e797a89e290063d112
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Get ready to squash all the HP Sandy Bridge and Ivy Bridge laptops
together, so as to factor out lots of repeated code.
Tested with BUILD_TIMELESS=1, binary does not change.
Change-Id: I0b68e524b57e3705e91e3cd98be5571b3554bd67
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
- Disable Windows driver DPST function
- Set POST resolution to 1800x1200
- Set POST brightness to 225 (0-255 scale)
Test: Boot Windows on EVE, verify display backlight control
functional and no lock ups from switching in/out of tablet mode.
Change-Id: Ida64a44df2449f1ff0dc5c8d0ec7b40a183566a7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
IMD provides support for small and large allocations. Region IMD Small memory is 1 KB
with 32 Bytes alignment, this region holds smaller entries without having to reserve a
whole 4 KB page. Remaining space is assigned to IMD Large to hold various regions with
4 KB alignment.
The UCSI kernel (kernel version 4.19) driver maps the UCSI_ACPI memory as not cached.
Cache mapping is set on page boundaries and all IMD Small is within the same page.
If another driver maps the memory as write-back before the UCSI driver is loaded then
the UCSI driver will fail to map the memory as not cached.
Placing UCSI_ACPI in IMD Large region will prevent this mapping issue since it will
now be located within its own page. This patch will force UCSI_ACPI region to be
located in IMD Large region.
BUG=b:144826008
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: Id00e76dca240279773a95c8054831e05df390664
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38414
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates pci dev definition according to TGL EDS.
Add GSPI3 case in chip.c according to updated pci dev definitions.
Reference
TGL Process EDS#575681 rev1.0
TGL PCH EDS#576591 rev1.2
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I4717ac3cc877b13978b18ada504740512f10c709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38341
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When a VBOOT enabled system is used without ChromeOS it may be valid to
allow the UDC independent of the vboot state.
Provide the option to always allow UDC when CHROMEOS is not selected.
BUG=N/A
TEST=build
Change-Id: I6142c4a74ca6930457b16f62f32e1199b8baaff8
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The new documentation describes typical ways that mainboards will
set up their GPIOs, as well as the distinction between "early"
and "normal" GPIOs. It also describes the typical properties
that GPIO configuration will cover.
Change-Id: I279eec4ed2bb0248a2bdb363fb73b40b8272267f
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Code in SMM segment using cmos_post_code will give compiler error since
cmos_post_code function is not getting compiled during SMM stage.
Also as per patch discussion, CMOS uses a split IO transaction and it's not
really safe to call cmos_post_code from SMM context. Thus we'll hide the
call for SMM context.
Change-Id: Iffdcccaad48e7ad96e068d07046630fbe4297e65
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Read the CPU temperature from the EC.
For this board the EC support is limited to reading the CPU temperature
sensor at this moment. Events are not supported.
BUG=N/A
TEST=tested on facebook monolith using acpidbg
The TSR0._TMP method is returning the correct values.
Change-Id: I6793070602e253f1e15cfc641bb47d25d269b136
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
When vboot was first integrated into CBFS it was still part of Google
vendorcode. So to not directly tie custom vendorcode into the core CBFS
library, the concept of cbfs_locator was introduced to decouple core
code from an arbitrary amount of platform-specific implementations that
want to decide where the CBFS can be found.
Nowadays vboot is a core coreboot feature itself, and the locator
concept isn't used by anything else anymore. This patch simplifies the
code by removing it and just calling vboot from the CBFS library
directly. That should make it easier to more closely integrate vboot
into CBFS in the future.
Change-Id: I7b9112adc7b53aa218c58b8cb5c85982dcc1dbc0
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch removes the CBFS locator override for the Apollolake SoC and
instead integrates the extra sanity check it was used for straight in
the boot device initializer.
Change-Id: Iccdb885be233bb027a6a1f2cc79054582cbdf3fc
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Update the IccMax for the SYSTEM_AGENT and IA_CORE power supplies
according to the information in the schematic. The IccMax for these
supplies is lower than the standard supported by the SoC.
BUG=N/A
TEST=build
Change-Id: I20b92e7dfc85427bcf9cb9f0efda02459c862809
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Provide Puff with it's own copy of ec.h copied from the
baseboard/includes however with the battery, lid and ps2
defines stripped.
This is to ensure the correct ASL is generated so that we don't
advertise PS2 keyboard support and battery/lid interrupts which
don't exist.
V.2: drop EC_ENABLE_ALS_DEVICE as well.
V.3: set MAINBOARD_EC_SMI_EVENTS to 0 and drop
EC_HOST_EVENT_LID_CLOSED smi event.
V.4: drop EC_HOST_EVENT_MODE_CHANGE &&
provide wake pin for EC for _PRW WoL method
V.5: drop EC_HOST_EVENT_KEY_PRESSED
BUG=b:147850335
BRANCH=none
TEST=builds
Change-Id: If13bd124c7229ced996efb841980604d13be09af
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
By grouping the spi flash parts by their {vendor, sector topology}
tuple one can use a common probe function for looking up the part
instead of having per-vendor probe functions. Additionally, by
grouping by the command set one can save more space as well. SST
is the exception that requires after_probe() function to unlock the
parts.
2KiB of savings in each of verstage, romstage, and ramstage
on Aleena Chrome OS Build.
Change-Id: I9cc20ca0f3d0a1b97154b000c95ff2e7e87f3375
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
To further drive to a common approach for describing the spi flash
parts in the drivers add spi_flash_part_id object. All the drivers
are updated to utilize the new object. Additionally, the driver_private
is also not needed in the spi_flash object.
A Chrome OS build of Aleena provides 960 byte saving of text. A subsequent
patch will save more memory.
Change-Id: I9c0cc75f188ac004ab647805b9551bf06a0c646b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
There was code to handle the case of continuation bytes for identifying
the manufacturer id to a jedec rdid command. However, all the parts that
currently supported have this defined to be 0. Remove the unused
continuation byte support.
Change-Id: Ia7c63162e4ef9dc46ef916ca8c31ebd721cbeca7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38361
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch moves common pch code SOC_INTEL_COMMON_BLOCK_THERMAL Kconfig selection
into SoC specific Kconfig selection as PCH thermal device is not available
with latest PCH (i.e. TGP and JSP).
Also added TODO for TGL thermal configuration as applicable.
TEST=Able to build and boot TGL RVP with this CL
Change-Id: Ibce17cc9f38fb666011ccd8f97bee63033ff5302
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38444
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The adesto, amic, atmel, and stmicro spi flash drivers didn't have
the status() call back. These parts do support the status command
retrieval. Fill them in accordingly.
Change-Id: Ie0e63bec844b8e01e292ef8c4df707494df02e69
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Put the write protection into its own object. This allows
for easier future reuse of objects in future consolidation
patches. It's also possible to eliminate the code implmementing
these in the future if the platform doesn't require it. For now
leave current behavior as-is.
The names of the callbacks were shortened as they are now in
the spi_flash_protection_ops object which is a new field in the
spi_flash object.
Change-Id: I2fec4e4430709fcf3e08a55dd36583211c035c08
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
spi_flash_erase() and spi_flash_write() already assume their
respective callbacks are supplied in the spi_flash_ops object.
Make the same assumption in spi_flash_read(). In order to do this
the spi_flash_ops objects from the drivers need to reference the
the previously used fallback read command, spi_flash_read_chunked().
This function is made global and renamed to spi_flash_cmd_read() for
consistency.
By doing this further dead code elimination can be achieved when the
spi flash drivers aren't included in the build.
A Hatch Chrome OS build achieves a further text segment reduction of
0.5KiB in verstage, romstage, and ramstage.
Change-Id: I7fee55e6ffc1983657c3adde025a0e8c9d12ca23
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is to get a uniform format that matches the macros added in the
next patch, so that said follow-up patch won't change the output binary.
lenovo/x230 still boots with this patch.
Change-Id: Ibfbeb847cab09427a57bef3cbd2069036de5a21e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The fast spi driver implements hardware sequencing which abstracts away
the underlying spi flash commands in the hardware block. It also has its
own spi flash probe function to intercept the spi flash ops. As such it's
not necessary to include all spi flash drivers.
On a hatch Chrome OS build this saves 9.5KiB of text in each of verstage,
romstage, and ramstage.
Change-Id: Ifb1b962cde3a6a02353ddf83279234057a9ec2fa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add a new Kconfig option, SPI_FLASH_DONT_INCLUDE_ALL_DRIVERS,
to make it easier for other parts of the code base to indicate that
all spi flash drivers should not be included.
Change-Id: Ibf2c4f1d2b8a73cff14bb627ddf759d7970920ea
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
LyCx(r, x, y) was a duplicate of the CxLy(r, x, y) with different order
of computation, so that the big refactoring doesn't change the output
binary of a timeless build. Now this workaround can be dropped.
Tested on lenovo/x230: still boots
Change-Id: I251b4dd383f954b27f392190092e06a9a06668e2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The current BIOS-extracted VBT breaks backlight control
with Tianocore, so replace it with one that does. Settings
were exported using Intel BMP tool and the overlayed onto
a GOP-format (vs BIOS format) VBT file.
Test: boot google/wolf with both SeaBIOS and Tianocore payloads,
verify backlight control functional under both Linux and Windows.
Change-Id: Id6281c8dfb6e0001be8c4d9be1013f2d4bbb5880
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
There are more instances of PCI_DEV(0, 0, 0), so use the macro for them.
Note that the resulting code with PCI_DEVFN(0, 0) is weird. It shall be
replaced with config_of_soc() in a follow-up.
Tested with BUILD_TIMELESS=1, resulting binary is identical.
Change-Id: Ia50965a108a734d192b584291a0796a2f2bc3a55
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38338
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a initial mainboard code aimed to serve as base for
further mainboard check-ins.
This is a copy patch from icelake_rvp as on commit ID:
I64db2460115f5fb35ca197b83440f8ee47470761
Below are the changes done over the copy patch:
1. Rename "Icelake" with "Tigerlake".
2. Replace "icelake_rvp" with "tglrvp".
3. Rename "icl" with "tgl".
4. Remove unwanted SPD file, add empty SPD as
placeholder.
5. Replace "soc/intel/icelake" with "soc/intel/tigerlake".
6. Empty romstage_fsp_params.c, to fill it later with
SOC specific config.
7. Empty GPIO configuration, to be filled as per board.
8. Change copyright year to 2019.
9. Add board support namely BOARD_INTEL_TGLRVP_UP3
10. Replace icl_u and icl_y variant with tglrvp variant.
11. Remove basebord gpio.c and rely on variant override.
12. Remove HDA verb table and config support.
Changes to follow on top of this:
1. Add correct memory parameters, add SPDs.
2. Clean up devicetree as per tigerlake SOC.
3. Add GPIO support.
4. Update chromeos.fmd to make 32MB BIOS region.
5. clean up and make empty devicetree setting
TEST=Build tigerlake rvp board
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I86ada611de1cf28a1b872eea35cf41c0dc1c57f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
A function draw_rounded_box() is added to draw a box with rounded
corners. In addition, this function is different from draw_box() in 2
ways:
- The position and size arguments are relative to the canvas.
- This function supports drawing only the border of a box (linear time
complexity when the thickness is fixed).
BRANCH=none
BUG=b:146105976
TEST=emerge-nami libpayload
Change-Id: Ie480410d2fd8316462d5ff874999ae2317de04f9
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37757
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
ByteLane is used unitialized from prior for statement,
creating a potential out-of-bound read of RxOrig[MaxByteLanes].
PassTestRxEnDly[MaxByteLanes] never appears as rvalue; all for
loops have ByteLane < MaxByteLanes exit condition.
Change-Id: Icd18a146aba6b6120d37518d8c40c7efbc05afa3
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241804
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
New Kconfig for Jasperlake soc was created and fsp_param for Jasperlake
has differences compared to Tigerlake. Thus renaming fsp_params.c to
fsp_params_tgl.c to point out correct file as per soc selected.
Also adding new file for fsp_param_jsl for Jasperlake SoC and currently
its the copy of fsp_param_tgl.
TODO: update files with correct fsp_params
Change-Id: I12815ae28a1eb4c64afda0a85b5c14fc0da3e4b1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37267
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All other messages in `ec/lenovo/h8` are prepended with *H8*, so also prepend
the EC version log message with *H8*.
EC Firmware ID 79HT50WW-3.4, Version 7.01A
No CMOS option 'usb_always_on'.
H8: BDC detection not implemented. Assuming BDC installed
H8: WWAN detection not implemented. Assuming WWAN installed
No CMOS option 'fn_ctrl_swap'.
Change-Id: Ib4f341946a336b57bd96c053a05364276caad1ac
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
These values are the same that were hardcoded in autoport before. As
done in commit 08caa79 (util/autoport: Trim gfx.did to size), ensure
that the hardcoded values make at least some sense.
Change-Id: I9950fd10e45f5016611a5d5b6a9e41c2b0f25a5f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38086
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set up the proper IRQ routing for OHCI/EHCI devices which appear if
XHCI controller is disabled (CONFIG_HUDSON_XHCI_ENABLE is not set).
Now both "USB 3.0" ports are working fine at OHCI/EHCI "USB 2.0" mode.
They also work fine if XHCI controller is enabled.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I50a773eeab890627abc963e0a61f781d1cea3259
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Due to build rules, dummy acpi_tables source files were added in many
mainboards. With commit 1e83e5c61a
("src/arch/x86: Build mainboard acpi_tables source if present"),
the build system will build mainboard acpi_tables only if present. Remove
the dummy/empty/blank acpi_tables source files.
BUG=None
TEST=Build test with some google mainboards.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0cef34368e2e5f5e3b946b22658ca10c7caad90a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
According to intels datasheet
Document Number: 341078-001
10th Generation Intel® Core™ Processor Families
Volume 2 of 2
we can dump the ICL MCHBAR similiar as on 8th / 9th gen CPUs.
The difference is that on ICL the MCHBAR address is definited by
the bits 38:16 instead of 38:15 giving the constraint that it has
to be 64kbit instead of 32kbit aligned. (Section 3.1.13)
Change-Id: Ia597a4b3738c11cb48ce5808d8459b4a2a768077
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Since all the `subsystemid` lines in these devicetrees use the same
values, factor them out via inheritance.
There are some exceptions though. There are some enabled devices which
lack a `subsystemid` entry. Looks like HP uses the same subsystem ID
on every device, so assume that these devices should also use that
subsystem ID as well.
While we are at it, tidy up all the now-empty device blocks.
Change-Id: Iccd74fff9456e1204735a80ecc4f7685624cb78e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38081
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable COM2 port on SuperIO if UART index is 1. This change allows
to use full RS232 COM1 port for different purposes when COM2 is selected
as main port.
TEST=flash coreboot with console on COM2 and observer output with UBS-TTL
converter connected to COM2 header on PC Engines apu1
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I1e72c5a43a302658f86dafd863e5a67580eae3e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
While we are at it, also:
- Rename related variables to match the register names.
- Update some comments to better reflect what some registers are about.
- Add various FIXME comments on registers that seem to be used wrongly.
With BUILD_TIMELESS=1, this commit does not change the coreboot build of:
- Asus P8H61-M PRO with native raminit.
- Gigabyte GA-H61MA-D3V with native raminit.
- Lenovo Thinkpad X230 with native raminit.
- Lenovo Thinkpad X220 with MRC raminit.
Change-Id: I5e5fe56eaa90842dbbdd1bfbbcb7709237b4c486
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The HDA controller was disabled because no codec exists on the board.
However, this also disabled audio over HDMI.
To correct this, enable Azalia and the HDA controller in the devicetree.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: I7be2c29151dc9d6c247c3332fb9adfb34449c703
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Incorrect values read from a different memory region will cause
incorrect computations. VceFlags array size should be 4 based on
similar code in f15 branch, and because
f16kb/Proc/GNB/Modules/GnbInitKB/GnbF1TableKB.c only loads
4 values for VceFlags in DefaultPpF1ArrayKB. Leaving it at 5
results in an out-of-bounds read of PP_FUSE_ARRAY_V2_fld16
in line 901 of
f16kb/Proc/GNB/Modules/GnbGfxIntTableV3/GfxPwrPlayTable.c
when Index reaches 4.
Change-Id: I0242c0634e66616018e6df04ac6f1505b82a630f
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241878
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38056
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The RW_MRC_CACHE was not included in a UNIFIED_MRC_CACHE region which is
expected by some parts of the code.
Add the UNIFIED_MRC_CACHE and include the RW_MRC_CACHE in this region.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: I1654ca210dc2a8e976d698fd8330641da23e8380
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
DRAM calibration sets vcore to different voltages at different
frequencies. After DRAM calibration, vcore should be restored to the
default voltage, which is 800mV for both eMCP and discrete DDR devices.
BRANCH=kukui
BUG=b:146618163
TEST=bootup pass
Change-Id: Ia87b4ac78a32dbd4c4ab52e84d307cb46525afa1
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
For timestamps added before CBMEM coming online and call to
timestamp_sync_cache_to_cbmem(), ts_table->base_time was
subtracted twice. The second time though, the value of zero
was subtracted.
Make the stamps logged on the console relative to base_time too,
such that cbmem -1 and cbmem -c outputs will match.
Remove comments about postponing initialisation of timestamps
to ramstage, that does not happen anymore.
Change-Id: Ia786c12c68c8921c0d09bc58a29fefdc72bf0c6d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Replace a bunch of spaces with tabs, put host bridge and friends above
southbridge, fix "TPM Module" (Trusted Platform Module Module) and add
some empty lines to help the reader.
Change-Id: I3a89893f943057ef7a4f973eaa65dba259e8a49d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
In order to provide more consistent probing in future refactorings, pull out
the release from deep sleep path in STMicro's SPI flash probing function.
Call that function explicitly when RDID doesn't return anything at all.
The old STMicro parts, even if supporting RDID, won't decode that
instruction while in a deep power down state. Instead of re-issuing RDID after
the successful wake assume the id fixup is valid.
Change-Id: I46c47abcfb1376c1c3ce772f6f232857b8c54202
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Also change some of the types to match the register widths
of the controller. It is expected that these prototypes
will be used with SMBus host controllers inside AMD chipsets
as well, thus the change of location.
Change-Id: I88fe834f3eee7b7bfeff02f91a1c25bb5aee9b65
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38226
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Only smbuslib.c and spd_bin.c share the same prototypes for SMBUS
functions. Therefore, get_spd_smbus() currently only works with
soc/intel/.../smbuslib.c and can be implemented there locally.
This allows removal of <device/early_smbus.h>.
Change-Id: Ic2d9d83ede6388a01d40c6e4768f6bb6bf899c00
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add missing BeforeInitLate hooks in order to bring back certain options
that were lost on postcar migration. This will also allow to disable
CDIT again that caused AmdInitLate error on 00730F01.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I1226e9c0c8a92920f2569ec0f85d0be0adcc9e30
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Update Kconfig:
- use CAR NEM mode for tigerlake only as NEM Enhanced is under debug
- update GSPI, RP max device #s according to
PCH EDS#576591 vol1 rev1.2
- update UART M/N setting according to new PCH baseclock
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I04020d55f1063d521b15f8d0dabbd6f1dabf577c
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
* Add function to generate unique _UID using CRC32
* Add function to write the _UID based on a device's ACPI path
ACPI devices that have the same _HID must use different _UID.
Linux doesn't care about _UID if it's not used.
Windows 10 verifies the ACPI code on boot and BSODs if two devices
with the same _HID share the same _UID.
Fixes BSOD seen on Windows 10.
Change-Id: I47cd5396060d325f9ce338afced6af021e7ff2b4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
This patch creates a common instance of northbridge.asl inside intel common
code (soc/intel/common/block/acpi/acpi) and changes cnl,icl & tgl soc code to
refer northbridge.asl from common code block.
TEST=Able to build and boot Hatch and ICL DE system. Dump DSDT.asl to verify
Device(MCHC) presence after booting to OS.
Change-Id: Ib9af844bcbbcce3f4b0ac7aada43d43e4171e08b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38155
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SPI_FLASH_FAST_READ_DUAL_OUTPUT_3B option is no longer
being used in the code. There's a runtime check for supporting
fast read dual output mode of the spi flash. Remove the references
to SPI_FLASH_FAST_READ_DUAL_OUTPUT_3B.
Change-Id: Ie7d9d3f91f29a700f07ab33feaf427a872bbf7df
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38166
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove fixed IccMax values for all domains.
IccMax will be selected by CPU SKU in
fill_vr_domain_config function.
BUG=b:145094963
BRANCH=None
TEST=build coreboot and fsp with enabled fw_debug.
Flashed to device and checked the log.
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Change-Id: I3f623d143f66c4f6ec63705844c9be7173feeb52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Add VR config IccMax, DC and AC loadline defaults for CML.
Add cpu_pl2_4_cfg to switch two kinds of VR design.
BUG🅱️145094963
BRANCH:none
TEST:build coreboot and fsp with enabled fw_debug.
Flashed to device and checked the log.
All VR configs were set correctly.
Change-Id: I3922bfad5c21dafc64fb05c7d9343b9835b58752
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Commit c9b13594eb removed the g_ prefix from
global variables, leaving the local "offset" variable shadowing the
global one. This commit partially reverts this by renaming one of the
occations and converting the flushing logic to work on the
global object.
Change-Id: I246ebdcfd3b973e6a4aa3c15fc5f32497dcf8398
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
List of changes in this patch
1. Remove unused variables
2. Make use of absolute path
3. Define macros and use inside SA ASL
4. Rearrange code in nothbridge.asl to move MCRS object under _CRS
Change-Id: Id74269ec5a96b087562ccdf2141233db5585ae59
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38154
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
The ACPI spec 6.3 chapter 6.1.10 states that _STR has to return a buffer
containing UTF-16 characters.
Add function to generate Unicode names and use it for _STR. It will
replace non-ASCII characters with '?'.
Use the introduced function in IPMI driver.
Fixes ACPI warning shown in fwts.
Change-Id: I16992bd449e3a51f6a8875731cd45a9f43de5c8c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37789
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SPI flashes that support page programming mode had duplicated
the logic for writing in every driver. Add
spi_flash_cmd_write_page_program() and use the common implementation
to reduce code size that comes from duplication. The savings is
~2.5KiB per stage where the spi flash drivers are utilized.
Change-Id: Ie6db03fa8ad33789f1d07a718a769e4ca8bffe1d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The BMC and tools interacting with it depend on metadata placed inside
the ROM in order the flash the BIOS.
Add a new tool smcbiosinfo, integrate it into the build system, and
generate a 128byte metadata file called smcbiosinfo.bin on build.
You need to provide the BoardID for every SMC mainboard through a new
Kconfig symbol: SUPERMICRO_BOARDID
Some fields are unknown, but it's sufficient to flash it using SMC
vendor tools.
Tested on Supermicro X11SSH:
* Flashing using the WebUI works
* Flashing using SMCIPMITool works
No further validation is done on the firmware.
Change-Id: Id608c2ce78614b45a2fd0b26d97d666f02223998
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add VR config IccMax, DC and AC loadline defaults and voltage regulator
maximum for all CFL, CNL and WHL.
This supports mainboards with replaceable CPUs and provides sane defaults
for boards that are missing the devicetree overwrite.
Remove the default IccMax to make use of the introduced lookup-table.
Also change some hex values to decimal.
I couldn't find CML datasheet, so those are left out for now.
Used Doc #337344 and #338023 Section 7.
Change-Id: I1d2e174157d468830cc0baf2a2d8295ef61a1a63
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37466
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There was one user of SPI_FLASH_SECTOR_ERASE_TIMEOUT_MS,
southbridge/intel/common/spi.c. Remove the define and encode
the 1 second timeout that it was wanting at the single use site.
Change-Id: If33a1a04bc4d3441e90bf0ca305ddf71c4f8bb88
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The SST25VF064C supports page programming mode like other spi flash
parts in that there isn't an offset requirement. Remove this
check and single byte program because CMD_SST_BP (0x2) is the
same as page programming command. Lastly, for clariy purposes provide
a CMD_SST_PP to explicitly indicate page programming despite the
values (0x2) being the same as byte programming for the other parts.
Change-Id: I84eea0b044ccac6c6f26ea4cb42f4c13cf8f5173
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37959
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This removes all the duplicated code and logic and leverages
the existing ones in libraries themselves. The current side
effect is that protection cannot be fully enabled because the
read, write, and write enable command are not exposed in struct
spi_flash currently. That support can be revised if protection
scheme makes sense for our use-cases once it's better understood.
BUG=b:146928174
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I8faf9cc719ee33dd9f03fb74b579b02bbc6a5e2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37957
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Let the linker trim unused net driver symbols when unused
in devicetree rather than being overly zealous in the Kconfig.
BUG=b:146592075,146999042,146999043
BRANCH=none
TEST=Boot to kernel.
Ensure we have ip address and corresponding mac
address with ifconfig.
Ensure ethernet controller shows up with lspci.
Change-Id: Ie98d0f9f9b77cb9ee4e52f6c95b68bcbdd94f2cc
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Implement a free() that supports only the last malloc(). Rewind
the heap to the last allocation point if the ptr to be freed is
matching the end of heap before last malloc(). With current situation,
since free() is no-op, every call to malloc() is a memory leak.
BUG=b:140124451
TEST=Wrote a test function to do malloc and free operations.
Change-Id: I6d43cf54b79e6897cf6882335730b2310e4eae45
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
While I was working on updating the headers to move copyrights into
the AUTHORS file, I got a request to switch to SPDX headers as well.
Linux has moved completely to SPDX headers, which are easier to
maintain, have good definitions, are very short, and can be checked
automatically. This is completely unlike our current header situation.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ie86d34f7fa7bf7434ad8a38aa1eadcfece7124b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
In preparation to update to SPDX license headers, add identifiers
for the licenses seen in the coreboot project and create a command
line parameter allowing only SPDX license identifiers to be detected.
Here are example locations of these licenses:
Apache-2.0 - src/soc/sifive
BSD-3-Clause - Throughout coreboot & libpayload source
GPL-2.0-only - Throughout coreboot source
GPL-2.0-or-later - Throughout coreboot source
GPL-3.0-only - util/amdtools
GPL-3.0-or-later - src/lib/[gcov/libgcov/gnat]
ISC - src/lib/ubsan.c, soc/qualcomm/ipq806x/include/soc/gsbi.h, others
MIT - soc/nvidia/tegra210/mipi_dsi.c, files in mainboard/cavium/
X11 - include/device/drm_dp_helper.h, drivers/aspeed/common/ast_tables.h
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I07a7ca408ac8563e03e189d05ef7729dfb6fc24e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This is a initial mainboard code aimed to serve as base for
further mainboard check-ins.
This is a copy patch from icelake_rvp as on commit ID:
I64db2460115f5fb35ca197b83440f8ee47470761
Below are the changes done over the copy patch:
1. Rename "Icelake" with "Jasperlake".
2. Replace "icelake_rvp" with "jasperlake_rvp".
3. Rename "icl" with "jsl".
4. Remove unwanted SPD file, add empty SPD as
placeholder.
5. Replace "soc/intel/icelake" with "soc/intel/tigerlake"
as tigerlake SOC hosts jasperlake code as well.
6. Empty romstage_fsp_params.c, to fill it later with
SOC specific config.
7. Empty GPIO configuration, to be filled as per board.
8. Change copyright year to 2019.
9. Add two board support namely BOARD_INTEL_JASPERLAKE_RVP
and BOARD_INTEL_JASPERLAKE_RVP_EXT_EC
10. Replace icl_u and icl_y variant with jslrvp variant.
11. Remove basebord gpio.c and rely on variant override.
12. Remove HDA verb table and config support.
Changes to follow on top of this:
1. Add correct memory parameters, add SPDs.
2. Clean up devicetree as per jasperlake SOC.
3. Add GPIO support.
4. Update chromeos.fmd to make 10MB BIOS region.
TEST=Build jasperlake rvp board
Change-Id: I3314215807959b7348b71933fbba98e6487c0632
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Let coreboot know there is a NIC device on the end so
that the mac from vpd is set at early boot.
Properly configure the link-leds in devicetree s.t.
valid values are written out to the register at initialization.
BUG=b:146592075,146999042,146999043
BRANCH=none
TEST=Boot to kernel.
Insert mac address into VPD
vpd -s ethernet_mac=<address>
reboot the system.
Ensure we have ip address and corresponding mac
address with ifconfig.
Ensure ethernet controller shows up with lspci.
Change-Id: I76ce6d8a5a26842fcb2544ee96567fe0da8603b1
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
To print times with 1 us resolution just adds unnecessary noise
when comparing logs across different boots. Furthermore, just
the printk itself is 1 ms if some slow console is enabled.
Change-Id: Ibea43124a1937f404a6e71fd9431086b2b72290a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
For each boot_state, report the times spent interleaved
with other console output and remove the samples arrays.
The time spent to report the times to console is not
accounted for.
Change-Id: I0c847da98901c56b356b4a933d9ae865dada98b6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
After C_ENVIRONMENT_BOOTBLOCK became mainstream, coreboot build system
starts to produce larger bootblock, conflicting with former default
offsets.
This change makes these offsets configurable before building, with
default values lower than before, to better fit the larger bootblock.
Change-Id: Ie022663a4d0df7f431865b55f7329a9ebb90863b
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37778
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Recent changes to the Atmel touchscreen driver in the mainline
kernel broke functionality with devices running upstream coreboot,
due relying on another driver (chromeos_laptop) which makes the
assumption that the i2c devices are be in PCI mode (as with the
stock Google firmware) rather than in ACPI mode as they are in
upstream coreboot.
Mitigate this by adding the required devicetree property so the
Atmel toushcreen driver will correctly attach without the use
of chromeos_laptop.
Test: build/boot peppy on 4.18+ kernel, verify touchscreen working
Change-Id: I05df8367886eef55b409590f75a68d98d4e5fbdf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicolò
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Provide the PM1_TMR information in the FADT even if PmTimerDisabled is
set because PM timer emulation is enabled via MSR 121h so the timer will
still work and can be used by things like Tianocore and Windows.
Porting from 662b6cb3ed (soc/intel/skylake: Always add PM1_TMR block to FADT).
Change-Id: Ie3d592623f3a84051477ffe83a0cf0daf30dd36f
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Assume that LIMIT_POWER is not requested if the ec does not support it.
Do this by checking the command code in the response message instead
of return value.
BUG=b:146165519
BRANCH=None
TEST=Boot puff with EC which does not support LIMIT_POWER param.
Change-Id: Ib2f5f69a53f204acebfab3e36aab2960eeec1204
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
The gnvs structure was zeroed out already in the following files:
* src/southbridge/intel/i82801ix/lpc.c (t400 and x200)
* src/southbridge/intel/i82801gx/lpc.c (thinkcentre_a58)
Change-Id: Id7d552e1c4084a0b36b98f9627a85a75c8b90e81
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
create_coreboot_variant.sh now supports the Volteer baseboard in
addition to Hatch. The shell script and supporting python code are
moved up one level, while retaining the ${BASE}/template/* file
structure for each supported baseboard.
kconfig.py has to add slightly different text to Kconfig.name
depending on which baseboard is selected.
BRANCH=None
BUG=b:146646594
TEST=Create variants of Hatch and Volteer, check that the staged
commits are correct.
$ ./create_coreboot_variant.sh hatch sushi b:12345
src/mainboard/google/hatch/Kconfig and Kconfig.name will have new
sections for SUSHI. src/mainboard/google/hatch/variants/sushi
will have a copy of util/mainboard/google/hatch/template
$ ./create_coreboot_variant.sh volteer ripto b:12345
src/mainboard/google/volteer/Kconfig and Kconfig.name will have new
sections for RIPTO. src/mainboard/google/volteer/variants/ripto
will have a copy of util/mainboard/google/volteer/template
Also run the script with an existing board name to verify that you
can't create a variant that already exists.
Change-Id: I084b6c50bb76af0d11dc86a96b3c3c434569a0dd
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Marco Chen <marcochen@google.com>
We found the driver binding failure issue could be cleared with 100ms
of "reset_delay_ms". Needs further check with device vendor, anyway it
seems the IC need some time before communication after de-assertion of
reset.
BUG=b:129159369
BRANCH=firmware-hatch-12672.B
TEST=Verified driver bound successfully.
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: Iccb33c13c9a390a2c971325c74c0c4ad4b08618e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
If the EC doesn't support the EARLY_EC_SYNC we don't properly set power
limits to reasonable defaults and can wedge the AP by browning out at
the end of vboot.
BRANCH=none
BUG=b:146165519
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I4e683e5a1c5b453b3742a12a519cad9069e8b7f7
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37930
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
related LTE GPIOs:
GPIO_67 - EN_PP3300
GPIO_117 - FULL_CARD_POWER_ON_OFF
GPIO_161 - PLT_RST_LTE_L
1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161
2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67
3. Power reset:
- keep GPIO_67 and GPIO_117 high and
- pull down GPIO_161 for 30ms then release it.
BUG=b:146843935
BRANCH=octopus
TEST=build and verify on the DUT with LTE
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: Ief6c993ede2bb4b3effbb05cfe22b7af4fcf7faf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Add a new driver to support reading a board serial number from
a text file in CBFS and injecting into the SMBIOS tables.
Allow driver to be selected at the .config level and not require
inclusion at the board level.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: Ieae39f39ab36e5b1f240383b7cf47681d9a311af
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Revert two of the changes made in
"arch|cpu/x86: Add Kconfig option for x86 reset vector"
I6a814f7179ee4251aeeccb2555221616e944e03d
The Intel FIT pointer and the ID section should be offsets from the
top of flash, and aren't inherently tied to the reset vector or to
bootblock.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I2c9d5e2b2c4248c999d493a72d90cfddd92197cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
The APOB NV region holds the save data for resuming. Omit it if the
mainboard doesn't use HAVE_ACPI_RESUME.
The APOB information will also be board-specific so remove the
default values.
Change-Id: I65a70bb86ad1f3c11ce37d0afa5a6fdd08bc46e2
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Update Eve's VBT from v211 to v221, and change the backlight
control type from PWM to VESA eDP/AUX. This allows the OS to
select the proper backlight control type for the panel.
Test: Eve backlight control now functional under Windows 10
(Linux requires some pending patches to fix)
Change-Id: I8be2a719765891b3f2702c1869981009fa73ca05
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch makes below clean-up for report_cpu_info() function.
1. Remove unused variables.
3. Reuse fill_processor_name.
TEST = Successfully able to boot hatch and verify the
cpu_name "CPU: Intel(R) Core(TM) i5-10210U CPU @ 1.60GHz"
Change-Id: I41c76eb93f0c5229c4a49ab041339b6ad51ad24a
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
This patch keeps required pch_early_init() function like ABASE programming,
GPE and RTC init into bootblock and moves remaining functions like TCO
configuration and SMBus init into romstage/pch.c in order to maintain only
required chipset programming for bootblock and verstage.
Rename the pch_init function to bootblock_pch_init and romstage_pch_init
according to the stage it is defined in.
TEST=Able to build and boot hatch successfully.
Change-Id: Idf7b04edc3fce147f7857561ce7d5b0cd05f43fe
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
This patch renames pch_init function to bootblock_pch_init and
romstage_pch_init according to the stage it is defined in.
TEST=Able to build and boot soraka successfully.
Change-Id: Idf7b04edc3fce147f7957561ce7d5a0cd05f53fe
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Unlike other Panther Point boards, the ga-b75m-d3h lacks definitions
to wire SuperSpeed-capable ports to XHCI in its devicetree, causing
these ports being wired to the second EHCI, and only working as USB
2.0 ports. The missing register definitions are added to fix that.
Tested on my ga-b75-d3v board.
Change-Id: Ida4de26f1a493ead83065b1ab27c0c684a074513
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Running the x86_64 qemu mainboard target with '-accel kvm' results in hang,
as the 'D' and 'A' bits needs to be set in read only page tables.
Tested on QEMU Q35: Boots into payload with '-accel kvm'.
Change-Id: I4beae8deec6bf34f9762e7b54c5da4e5b63f6d24
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36778
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Switching was done by moving a SIO configuration and
the clocks setup from 'romstage.c' to 'bootblock.c',
following the example of change CB:37719 (fc749b2).
TEST=Boots into Artix Linux 2019 without a problem.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I780fa87cb9cb3c45844c388331ef89eb8eb70ebb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
If the board doesn't provide VRconfig in devicetree make sure to use
the lookup table for IccMax instead of defaults for some mobile SoC.
Also use decimal values instead of hex.
Change-Id: If31063f9b483a3bbd6cc90df1c1b76b4efc66445
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37598
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The baseboard GPIO table definitions are too straineous to the extend
that variants need to redefine assumptions back to NC. Invert this so
that baseboard by default assumes the safer NC and move the specific
board configurations to their respective places.
This patch handles the GPP_H3 gpio config for easier review. This
toggles the MAX amp which not all boards have. Move the pin
configuration to boards with the respective devicetree configuration
following on from the theme of commit b417786525.
BUG=b:142094759
BRANCH=none
TEST=builds
Change-Id: Iefd2223af79a13c8a42d07bc10b2772dbff6d3e5
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The baseboard GPIO table definitions are too straineous to the extend
that variants need to redefine assumptions back to NC. Invert this so
that baseboard by default assumes the safer NC and move the specific
board configurations to their respective places.
This patch handles the GPP_C15 group for easier review.
BUG=b:142094759
BRANCH=none
TEST=builds
Change-Id: I578245e24895d361d80ad016a4f18204e2b6e1ca
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The baseboard GPIO table definitions are too straineous to the extend
that variants need to redefine assumptions back to NC. Invert this so
that baseboard by default assumes the safer NC and move the specific
board configurations to their respective places.
This patch handles the GPP_A* group for easier review.
BUG=b:142094759
BRANCH=none
TEST=builds
Change-Id: I29b4323ac80b1288b2562846217c4f377714fc2c
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Generally work towards a more loose baseboard definition by moving out
some original assumptions to be board specifics. Specifically Puff does
not have the MAX98357A speaker amp and enabling the driver winds up
generating incorrect SSDT tables that confuse the kernel. Since
devicetree inherits the chip from device node in base and an override
will also inherit the chip and thus dispatch the unwanted fill_ssdt fn
call.
V.2: lean on linker to drop max98357a driver when not in dt.
BRANCH=none
BUG=b:146519004
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I8e7fed69a4c6d9610ac100da6bae147828ebfa81
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37909
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Two things here:
i. ) FSP requires that function 0 be enabled whenever any non-zero
functions hang under the same bus:device.
ii.) FSP reorders function 6 RP to be function 0 if function 0 is
indeed unused.
BUG=b:146437819
BRANCH=none
TEST=none
Change-Id: I0f499a23495e18cfcc712c7c96024433a6181a4c
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
* Make use of introduced SSDT config mode access
* Make use of introduced SSDT mutex
* Provide ACPI functions to safely access SIO config space
* Implement method to query LDN enable state
* Implement method to set LDN enable state
* Use introduced functions to implement _DIS and _STA in the device
* Update documentation
Tested on Aspeed AST2500 and Linux 5.2.
Manually verified ACPI code that generates no errors in Linux.
Change-Id: I520b29de925f368cd71ff8f1f58d2d57d72eff8d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
As discussed in CB:35077, since both measured boot and verified boot
depends on vboot library, it had better to introduce a dedicated flag
CONFIG_VBOOT_LIB to control the building and linking of the vboot
library, and make other flags needing vboot library select it. Only
the actual verification stuff should be conditional on CONFIG_VBOOT.
Change-Id: Ia1907a11c851ee45a70582e02bdbe08fb18cc6a4
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Tigerlake and Jasperlake fsp requires stack size to be minimum 192 KiB
and heap size to be minimum 128 KiB.
Updating both Kconfig to meet size requirements.
Also updated required CAR region size during boot block due to increment
in stack & heap requirement by fsp
Change-Id: I38e93b5986811ff3e0a8df5f4f36af35f308cb6b
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37764
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The delay cell result should use DDR clock PLL rate for computation,
and should not be divided by 2.
This helps to improve DRAM stability.
BUG=b:80501386,b:142358843
BRANCH=kukui
TEST=Boots correctly on Kukui
Change-Id: Idf5cce206e248bb327f9a7d27c4f364ef1c68aa1
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
PCI devices starting from 18 are processor configuration devices for each
node and are not a bus itself.
According to ACPI specification 6.3 section 6.1.5:
"... _HID object must be used to describe any device that will be
enumerated by OSPM. OSPM only enumerates a device when no bus enumerator
can detect the device ID. ... Use the _ADR object to describe devices
enumerated by bus enumerators other than OSPM."
PCI device 18 with its functions has a standard enumerator, which is PCI
enumerator so it needs a _ADR. Create a separate ACPI device for the
processor configuration space. This fixes the ACPI compliance problem
from CB:36318.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Ie7b45ce8d9e4fdd80d90752bf51bba4d30041507
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37835
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The MIC1 NID is configured incorrectly because of a typo. The value is 7
digits instead of 8. This is corrected by this patch.
No issues are known because of this (the MIC is not connected).
BUG=N/A
TEST=build
Change-Id: Ia12f3be7d7262829cce3400a8535a33ea1c54b78
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
FSP logo handling used PcdLogoPtr and PcdLogoSize which are elements of
the chipset specific FSP structures.
Create soc_load_logo() which will pass the logo pointer and size.
This function will call fsp_load_logo which will load the logo.
BUG=NA
TEST= Build and verified logo is displayed on Facebook FBG1701
Change-Id: I86943e64ca1ddd05e7e88fc6b882cfd33b98272e
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37791
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Missing bus init for RTL8111H ethernet chip hanging on bus.
V.2: Include admendments from Kangheui.
BRANCH=none
BUG=b:146437819
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I22aba312f183ea05eeb81d326ca0c05ce340a2e8
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Seems nothing special is needed here from coreboot.
V.2: Fix typo as well in speed map.
BRANCH=none
BUG=b:143047058
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: Ief750f98677b2017af78fb0b5bc98e1492dedbe4
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Remove the old Stoney Ridge postcar stack frame setup. Reduce
romstage.c to basic functionality. Until AGESA's reporting of
memory configuration is available, use the TOM register as an
indicator for the top of usable memory.
Change-Id: I516b79c3e798f5fc68c2771b2f66034c6867b19e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
No AGESA v5 binaryPI features are still present in the picasso directory.
Remove the PI and S3 selects. Remove DCACHE symbols. Remove all vboot
options until the new PSP-based solution is developed.
Change-Id: I6542578afafc0ee3c3117a971b1a021dbe53f42c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
If stage cache is enabled, we should not allow S3 resume
to load firmware from non-volatile memory.
This also adds board reset for failing to load postcar
from stage cache.
Change-Id: Ib6cc7ad0fe9dcdf05b814d324b680968a2870f23
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It was possible to have NO_STAGE_CACHE=n and at the same time have
TSEG_STAGE_CACHE=n and CBMEM_STAGE_CACHE=n. This resulted with a
failing attempt to load STAGE_POSTCAR from the stage cache, but not
loading it from CBFS either.
Make it a three-way choice between different STAGE_CACHE options.
For AGESA disable CBMEM_STAGE_CACHE by default, as it is no longer
needed to have functional ACPI S3 resume and it is not allowed
se use keyword select for symbols inside choice blocks.
Change-Id: I0da3e1cf4c92817ffabbb02eda3476ecdfdfa278
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37683
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP logo handling used FspsConfig.LogoPtr and FspsConfig.LogoSize which
are chipset specific.
Create soc_load_logo() which will pass the logo pointer and size.
This function will call fsp_load_logo which will load the logo.
BUG=NA
TEST= Build and verified logo is displayed on Facebook Monolith
Change-Id: I30c7bdc0532ff8823e06f4136f210b542385d5ce
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37792
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current build rules require adding blank acpi_tables in some of the
mainboards (eg. octopus, hatch). Update the build rules to compile the
acpi_tables.c only if it is present. This will help to avoid adding
blank acpi_tables.c source file.
BUG=None
TEST=Build test with octopus and hatch without blank acpi_table.c file.
Change-Id: I7dfacc6f4c737699b22acd96e17c9426d33574bd
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Implemented according to IPMI "Platform Management
FRU Information Storage Definition" specification
v1.0 for reading FRU data Product Info Area and
Board Info Area.
SMBIOS data can be updated with the FRU data.
Tested on OCP Mono Lake.
Change-Id: Id6353f5ce3f7ddd3bb161b91364b3cf276d020b8
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
(cherry picked from commit 8ac46b937c80822706c9d6c70ce7bbe61eb04f72)
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37095
Emmc spec, JEDEC Standard No. 84-B51, section 6.6.2.3, selection
flow of HS400 using Enhanced Strobe states that host should change
frequency to ≤ 52MHz when switching to HS speed mode first. In
current code, mmc_select_hs400() calls mmc_select_hs() to do this,
however caps are not cleared, so when switching from HS200 to HS400,
caps will still have DRVR_CAP_HS200, and mmc_recalculate_clock() will
set 200Mhz instead of ≤ 52MHz. As a result, switching to HS400 will
intermittently fail.
BUG=b:140124451
TEST=Switch speed from HS200 to HS400 on WHL RVP.
Change-Id: Ie639c7616105cca638417d7bc1db95b561afb7af
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37775
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Only headers from firmware/lib should be imported.
As far as I can tell, nothing imports 2lib headers
directly anymore, so we can get rid of this CFLAG.
BUG=b:124141368, chromium:968464
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ie5f3fe1d0180113b332e57ed07d4cfe563e7ecf2
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds a BOARD_GOOGLE_KEVIN variant config that enables
CONFIG_VBOOT_MOCK_SECDATA. This is to ensure that Jenkins will build the
MOCK_SECDATA-specific code at least once, to be sure we don't
accidentally break it during refactoring.
Change-Id: Ib0ffaccdf4601d6bfb889ae289d1d7df18bed1fd
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37773
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Joel Kitching <kitching@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Skylake soc code sets the length of the PCIe configuration space to 64
MB while the specification allows up to 256 MB. Linux reports "acpi
PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bos 00-3f] only
partially covers this bridge".
Remove "select PCIEX_LENGTH_64MB" from Kconfig so the default 256MB will
be used and the size can be reduced on the mainboard level when required.
BUG=N/A
TEST=tested on facebook monolith
Tested is by booting Linux 4.15 and analyzing the coreboot and Linux
dmesg to make sure the memory range is reported correctly and doesn't
create an overlap.
Change-Id: I8a06b9fba5ad561d8595292a73136091ab532faa
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37704
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed for
portable devices. It converts MIPI DSI/DPI to DisplayPort 1.3 4K.
BRANCH=none
BUG=b:140132295
TEST=emerge-jacuzzi coreboot
Change-Id: I02ef29798b0257632e0750f09a4390b3d0226367
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The base address of the 16 MB flash range was reported as 0xFFF00000
this causes the range to extend above the 4GB boundary.
Change the base to 0xFF000000 as is the case with e.g. Skylake.
BUG=N/A
TEST=build
Change-Id: Ia8de01769ced00c5ae13f255760401933230b88c
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
ACPI method TEVT is reported as unused by iASL (20190509) when ChromeEC support is not
enabled. The message is “Method Argument is never used (Arg0)” on Method (TEVT, 1, NotSerialized),
which indicates the TEVT method is empty.
The solution is to only enable the TEVT code in mainboard or SoC when an EC is used that uses
this event. The TEVT code in the EC is only enabled if the mainboard or SoC code implements TEVT.
The TEVT method will be removed from the ASL code when the EC does not support TEVT.
BUG=N/A
TEST=Tested on facebook monolith.
Change-Id: I8d2e14407ae2338e58797cdc7eb7d0cadf3cc26e
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Add VBTs for all rambi variants, extracted from VGA BIOS
from stock firmware images using intelvbttool.
Test: boot several rambi variants using MrChromebox edk2/master
branch with Baytrail GOP driver and extracted VBTs.
Change-Id: I401ae5accd852fc5211092a5944fc85871b642ae
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add VBTs for jecht variants, extracted from VGA BIOS
from stock firmware images using intelvbttool, zero-padded
to 0x11ff bytes to make the Intel BMP editor happy.
Use a common VBT for all except tidus, since it differs
from the others.
Change-Id: I570bdb749ef7d49f41539074220bb16c9c100342
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This impacts boards:
hatch (&variants) and drallion.
Some variants like Puff can have up to 12 cores. coreboot should take
the min() where MAX_CPU is the upper bound.
Further to that, boards themseleves shouldn't be setting the MAX_CPUS,
the chipset should be and so do that.
BRANCH=none
BUG=b:146255011
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I284d027886f662ebb8414ea92540916ed19bc797
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
-1 shouldn't be assigned to an unsigned variable, so use an otherwise
unused constant here. Since 7 is the highest virtual LDN number, using
0xffff as PNP_SKIP_FUNCTION marker has no unwanted side effects.
Change-Id: I5e31e7ef9dad5fedfd5552963c298336c533a5e9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Now RCOMP_TARGET_PARAMS is defined and used once in the definition of
the RcompTarget structure. All other structures in these functions use a
fixed value.
Replace RCOMP_TARGET_PARAMS with fixed value.
BUG=N/A
TEST=build
Change-Id: Ibe7c72c65975354433e9a0c613bda715eb782412
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37658
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To support showing CBMEM logs on recovery screen, add a function
cbmem_console_snapshot() to copy the CBMEM console to an allocated
buffer. Non-printable characters are automatically replaced with '?' to
ensure the returned string is printable.
BRANCH=none
BUG=b:146105976
TEST=emerge-nami libpayload
Change-Id: Ie324055f5fd8276f1d833fc9d04f60a792dbb9f6
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Add VBTs for beltino variants, extracted from VGA BIOS
from stock firmware images using intelvbttool, zero-padded
to 0x11ff bytes to make the Intel BMP editor happy. Use
a common VBT for all except monroe, since it differs as
it has a built-in display (being a Chromebase vs Chromebox).
Change-Id: I82afb20a5648695c2cd568384a26839ab28be3da
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add VBTs for all auron variants, extracted from VGA BIOS
from stock firmware images using intelvbttool, zero-padded
to 0x11ff bytes to make the Intel BMP editor happy.
Test: boot several auron variants with libgfxinit and Tianocore
payload, ensure both internal and external displays as well as
HDMI audio function properly under Linux (4.x/5.x).
Change-Id: Ibc4eabfa5d02b4c08755cf52835b5df8c1291fea
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Commit 77ad581ce [chromeec: PS2K node can't be under SIO node]
moved the PS2K ACPI device from under the SIO device to under
the LPCB, and while this fixed the keyboard under Windows for
Skylake devices, it was insufficient for Baytrail and Braswell
devices (and likely Apollo Lake/Gemini Lake too).
Moving the PS2K device under PCI0 allows the PS2K to be functional
under Windows for all Chrome-EC platforms.
Test: build/boot various Chrome-EC devices from IVB, HSW, BDW,
BYT, SKL, BSW, and KBL platforms, verify keyboard functional
under both Linux (4.x and 5.x) and Windows 10.
Change-Id: If773eea69dc46030b6db9d64c3855be49951d4c0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37542
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We had to role the `fsp` submodule back for a minute due to a regression
with the Coffee Lake binary. Intel silently mixed FSP 2.1 features into
the Coffee Lake FSP which is supposed to be FSP 2.0. With the stack and
heap usage partitioned for FSP using coreboot's stack (config FSP_USES_
CB_STACK), it works again.
To make this even messier: We already selected this Kconfig option for
Whiskey Lake, which is supposed to use the very same FSP binary. So with
either submodule pointer, something was always broken :-/
Change-Id: Id2aa17aaa2c843dcc7e0fb28779d1e5948da83c9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Mimoja <coreboot@mimoja.de>
Add an fmd file with a layout that allows configuring the system for
measured boot without enabling verified boot.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: I85fc6bee3f28fa4454d43df0e8bd1e511e1d0caf
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37673
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per the 4.11 release requirement, C_ENVIRONMENT_BOOTBLOCK=y
is a mandatory feature, which most AGESA and binaryPI boards lack.
Disable such platforms from the build for the time being.
The Kconfig symbol has been flipped, ROMCC_BOOTBLOCK=n is the
same mandated feature as C_ENVIRONMENT_BOOTBLOCK=y.
If a platform does not reach ROMCC_BOOTBLOCK=n within a
reasonable timeframe both the mainboard and the respective
unused platform support code will get removed.
Change-Id: I7fceb0370f7f4f5f52080277c5d21615d3ab3454
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This reverts commit 0178760867.
AMD: Dropping the _HID of PCI root bus doesn't work well and people
started to notice the breakage.
Intel: These platforms have a devicetree switch to choose between PCI
and ACPI modes. In the former case we need _ADR, but in the latter _HID
as the PCI devices are hidden.
The conflicting use of _ADR and _HID still needs to be fixed before
we can bump our IASL version.
Change-Id: If7b52b9e8f2f53574849aa3fddfccfa016288179
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37710
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The split of bootblock initialisation to cpu, northbridge and
southbridge is not specific to intel at all, create new header
<arch/bootblock.h> as AMD will want some of these too.
Change-Id: I702cc6bad4afee4f61acf58b9155608b28eb417e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
CB:36845 simplified how coreboot finds the RW CBFS after vboot has and
eliminated a layer of caching. Unfortunately, we missed the fact that
the former cached value didn't exactly match the FMAP section... it was
in fact truncated to the data actually used by vboot. That patch
unintentionally broke this truncation which leads to performance
regressions on certain CBFS accesses.
This patch makes use of a new API function added to vboot (CL:1965920)
which we can use to retrieve the real firmware body length as before.
(Also stop making all the vb2_context pointers const. vboot generally
never marks context pointers as const in its API functions, even when
the function doesn't modify the context. Therefore constifying it inside
coreboot just makes things weird because it prevents you from calling
random API functions for no reason. If we really want const context
pointers, that's a refactoring that would have to start inside vboot
first.)
This patch brings in upstream vboot commit 4b0408d2:
2019-12-12 Julius Werner 2lib: Move firmware body size reporting to
separate function
Change-Id: I167cd40cb435dbae7f09d6069c9f1ffc1d99fe13
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Updating from commit id 695c56dc:
2019-12-04 Julius Werner Makefile: Make loop unrolling fully
controllable by the caller
to commit id b10e5e32:
2019-12-09 Yu-Ping Wu vboot: Make 2nvstorage.h private to
vboot_reference
This brings in 19 new commits.
Change-Id: I9cdccd25422aee26620d48d31f83bcf32a7b4809
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37717
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SeaBIOS 1.13.0 has been tagged on 20191209. Major changes in this release:
* Support for reading logical CHS drive information from QEMU
* Workaround added for misbehaving optionroms that grab "int19"
* The TPM 2 "PCR bank" option can now be set from the TPM menu
* SeaVGABIOS support for QEMU "atiext" display
* Several bug fixes and code cleanups
see http://seabios.org/Releases
Change-Id: I37c8a72b0819bc4d19da9f7ab8e90f907e3e4dec
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
cbfstool depends on vboot headers, and vboot expects to be able to use
modern C features like _Static_assert(). It just so happens that it
doesn't do that in any headers included from cbfstool right now, but
that may change. Let's switch cbfstool to a newer version to prevent
that from becoming a problem.
Change-Id: I884e1bdf4ec21487ddb1bca57ef5dc2104cf8e0e
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
On nocturne, the VBT specifies that the native panel resolution
(3000x2000) is to be used by FSP/GOP init, which makes payload
and grub menus extremely difficult to read. Change the default
POST resolution specified by the VBT to 1500x1000 instead
(200% scaling) which is much more legible.
Test: build/boot nocturne with GOP init and Tianocore payload,
observe menu text is actually readable.
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Change-Id: I767a2b8319c7673e3460acfad534140409bf1d57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37621
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For low frequency (e.g., 1600 or 2400 Mbps) we can do fast
calibration for TX and RX window. However, for high frequency
(e.g., 3200 or 3600 Mbps) a full calibration is needed.
BUG=b:80501386,b:142358843
BRANCH=kukui
TEST=Boots correctly on Kukui
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I00d563ece4cf91ef5e8e12b6cf7f777849375a24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36921
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* GBB_HWID is no longer used in Hatch Kconfig, so remove the code
that creates the GBB_HWID and adds it to the Kconfig section
* Add more information in the usage message when the cmdline params
are incorrect.
* Remove messages that tell the user what to do, because the top-level
program that invokes this script will handle those commands, and so
this script telling the user what to do is noise (and possibly harmful)
* Add more information to the commit message that the script prepares
for the user.
* Bump script version number.
BRANCH=None
BUG=b:140261109
TEST=Create the "sushi" variant of the "hatch" baseboard:
`util/mainboard/google/hatch/create_coreboot_variant.sh sushi`
Inspect the files in src/mainboard/google/hatch/variants/sushi
Change-Id: I04e949aedce61ed7fc7df681b72c3cfef31b5513
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
* Implement reading EDID over software I2C.
* Fall back to VGA if no monitor connected for BMC KVM
* Copy the linux kernel code and add a bunch of wrapper structs to make it
compile.
* Convert the EDID to a drm_display_mode, which is understood by the
driver.
* Properly select HAVE_LINEAR_FRAMEBUFFER and HAVE_VGA_TEXT_FRAMEBUFFER
Tested on Supermicro X11SSH-TF using FullHD VGA monitor.
Initializes the graphics in about 1 second, which is twice as fast as the
VGA Option ROM.
The framebuffer is advertised and working in tianocore.
Change-Id: I7803566b64158405efc04a39f80a0ec98b44e646
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35726
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add early SuperIO initialization in bootblock to enable early console.
Also, remove some southbridge-specific initialization that has been
moved to southbridge bootblock initialization in previous patch.
The board obtains few additional timestamps: start of bootblock, end
of bootblock, starting to load romstage and finished loading romstage.
TEST=boot apu2 and launch Debian with Linux kernel 4.14.50
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: If770eff467b9a71d21eeb0963b6c3ebe72a88ef3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36915
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that we have a CONFIG_NO_FMAP_CACHE to completely configure out the
pre-RAM FMAP cache code, there's no point in allowing the region to be
optional anymore. This patch makes the section required by the linker.
If a board doesn't want to provide it, it has to select NO_FMAP_CACHE.
Adding FMAP_CACHE regions to a couple more targets that I think can use
them but I don't know anything about... please yell if one of these is
a bad idea and I should mark them NO_FMAP_CACHE instead.
Change-Id: Ic7d47772ab3abfa7e3a66815c3739d0af071abc2
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
While Merlin Falcon binaries are not available, make it explicit that it's
compiling for Prairie Falcon (it was being surreptitious about it).
Board Padmelon accepts 3 different SOC, just changing some resistors
(soldered or not): Brown Falcon, Prairie Falcon and Merlin Falcon. Code for
Brown Falcon is not currently available.
BUG=None
TEST=Build with prairie falcon.
Change-Id: I1663e4403a32a7d626dd2fa06763f18f4230457e
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Make a new Kconfig symbol for using soc//stoneyridge. This code also
supports Prairie Falcon is backward-compatible with Carrizo and Merlin
Falcon.
Although Bettong uses Carrizo, it does not currently rely on stoneyridge
source, so it is unaffected by this change.
Change-Id: I786ca54b0444cbcf36dc428a193006797b01fc09
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
The stoneyridge code inferred that if Merlin Falcon was built but no
Merlin Falcon binaries were present, the intent must be Prairie Falcon.
The two falcons are Embedded variants, and Prairie Falcon falls within
Family 15h Models 70h-7Fh.
Add a Prairie Falcon symbol that can be used explicitely. Drop
HAVE_MERLINFALCON_BINARIES.
Change-Id: I0d3a1bc302760c18c8fe3d57c955e2bb3bd8153a
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
'struct acpi_gpio' and 'struct acpi_irq' require the inclusion
of acpi_device.h. The only reason this wasn't caught previously
is due to the header being included with another driver compiled
first on the one board using it (google/eve).
Change-Id: I987f0ec6f769e550f3421629e0ef0c579a3d12f9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37539
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to the POSIX standard, %p is supposed to print a pointer "as
if by %#x", meaning the "0x" prefix should automatically be prepended.
All other implementations out there (glibc, Linux, even libpayload) do
this, so we should make coreboot match. This patch changes vtxprintf()
accordingly and removes any explicit instances of "0x%p" from existing
format strings.
How to handle zero padding is less clear: the official POSIX definition
above technically says there should be no automatic zero padding, but in
practice most other implementations seem to do it and I assume most
programmers would prefer it. The way chosen here is to always zero-pad
to 32 bits, even on a 64-bit system. The rationale for this is that even
on 64-bit systems, coreboot always avoids using any memory above 4GB for
itself, so in practice all pointers should fit in that range and padding
everything to 64 bits would just hurt readability. Padding it this way
also helps pointers that do exceed 4GB (e.g. prints from MMU config on
some arm64 systems) stand out better from the others.
Change-Id: I0171b52f7288abb40e3fc3c8b874aee14b9bdcd6
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Guckian
SDCARD_CD is defined in onboard.h but required in ASL only, move this
define to dsdt.asl.
Removed the onboard.h file from the ASL files that don use it.
BUG=N/A
TEST=build
Change-Id: I35b75e0ae2e2bc4ce143aaec6df6016774676095
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
ITE8258_CMD_PORT is used in com_init.c only.
Replace ITE8258_CMD_PORT by fixed value in the c file.
ITE8258_DATA_PORT is removed as this isn't used.
BUG=N/A
TEST=build
Change-Id: I401da3f127db9e65763fd8d115eb274fbadbefbe
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Location in hudson_lpc_port80() was called conditionally.
Also move hudson_lpc_decode() call after enable_acpimmio_decode_pmXX()
due the change from IO to MMIO using pm_read/write.
Change-Id: I38e94e4b04f0a493052cfd3ffdd0a9c2ac0d07fc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Disabling SSL verification is far from optimal, but depending on the
circumstances may be the most practical way, so describe how to do
that instead of leaving users confused.
It's also not _that_ bad because git's hashing scheme should uncover
most attempts to tamper with code, either when checking signed tags
or when people push (and see lots of modified commits).
State the command in a way that isn't conductive to careless
copy & paste.
Change-Id: Idbd52ba5d6e8b0f0e891fca16e4159ccef10771a
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
These boards currently have no build-testing, so they degrade
fast. Apply some of the build-tested changes we know to be
good from pcengines/apu2 to get them a bit closer to using
POSTCAR_STAGE=y.
Change-Id: Ibc9a15ed5e91c6dd857f2dd02e37d0979dd6ae90
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
The bayou payload is not attached to the build system in any way, and
has not been for quite a while. Since selecting it in Kconfig does
nothing, remove this payload now that coreboot 4.10 has been released.
Change-Id: Icfb18b88e460a4e4b538b7efe907d4eef6c40638
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: ron minnich <rminnich@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
It is an ATX board similar to existing ga-b75* boards. The major
difference is the configuration of pci-e ports on PCH, and on-board
pci-e NIC. (see below)
Tested:
- CPU i5 3570T
- Slotted DIMM 8GiB*4 from Kingston
- usb2 and usb3
- pci and pci-e ports
- sata
- Sound
- S3
- AR8161 NIC connected to 1c.2 with mac address burnt in efuse
- libgfxinit-based graphic init
- NVRAM options for North and South bridges
- tpm 1.2 on lpc (similar to ga-b75m-d3h)
- Linux 4.19.67-2 within Debian GNU/Linux stable, loaded from
SeaBIOS.
Change-Id: I1a969880e4da02abf8ba73aac60ee1296fe0abf2
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This commit is adding a dependency check for the FSP_USE_REPO
config option which so far was not able to deal with IceLake
systems.
Change-Id: I29faa8d3acff5680b611951fc193d33f514dc0d3
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37561
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some return codes were missed when implementing this initially; the vboot
logic can require the system to command the EC to reboot to its RO, switch
RW slots or it can require a poweroff of the SoC. This patch appropriately
handles these return codes.
BUG=b:145768046
BRANCH=firmware-hatch-12672.B
TEST=ODM verified this patch fixes the issues seen.
Change-Id: I2748cf626d49c255cb0274cb336b072dcdf8cded
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Change the hex values in the VR configuration tables of the Intel Kaby
Lake RVP boards to the same style that is used in the other mainboards.
Also, correct some numbers in the comment tables that did not match the register values.
The values in the tables haven't changed.
BUG=N/A
TEST=build
Change-Id: I77af544d7d88143e19abedb12a13627779c705c6
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37550
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Because the function is implemented in C, post_code() calls
from cache_as_ram.S and other early assembly entry files may
not currently work for cold boots. Assembly implementation
needs to follow one day.
This effectively removes PORT80 routing from boards with
ROMCC_BOOTBLOCK.
Change-Id: I71aa94b33bd6f65e243724810472a440e98e0750
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
The board is booting Linux and has been briefly tested.
SeaBIOS, TianoCore payload and Linux as payload all seem to work fine.
BUG=N/A
TEST=tested on Facebook Monolith
Change-Id: I65a2e03334af65cfb3f825d43fa0daa6e6c75913
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
On embedded boards the cpu mounted on the board is known. So it is not
required to include microcode for all possible Sky Lake and Kaby Lake
cpus. This patch provides the possibility to only support the versions
required.
By default all microcode updates will be included and the versions not
required can be removed using Kconfig.
BUG=N/A
TEST=build
Change-Id: Iaa36c2846b2279a2eb2b61e6c97d6c89d0736f55
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
The code in cpu/x86/lapic/apic_timer.c for timer_monotonic_get()
is not SMP safe as LAPIC timers do not run as synchronised as TSCs.
The times reported for console for boot_states does not accumulate
from APs now. Also remove console time tracking from ENV_SMM.
Change-Id: I1ea2c1e7172f8ab3692b42dee3f669c5942d864a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37398
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
factory_initialize_tpm() calls secdata_xxx_create() (for both firmware
and kernel space) and then immediately writes those spaces out to the
TPM. The create() functions make vboot think it just changed the secdata
(because it reinitialized the byte arrays in the context), so we also
need to clear the VB2_CONTEXT_SECDATA_xxx_CHANGED flags again, otherwise
vboot thinks it still needs to flush the spaces out to the TPM even
though we already did that.
Also clean up some minor related stuff (VB2_CONTEXT_SECDATA_CHANGED
notation is deprecated, and secdata space intialization should use the
same write-and-readback function we use for updates).
Change-Id: I231fadcf7b35a1aec3b39254e7e41c3d456d4911
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Going forwards, vb2ex_commit_data will be used to flush both
nvdata and secdata.
The patch that is circularly dependent on this lies between a patch that
makes vboot no longer build and the patch that fixes that, so we have to
pull the whole thing in at once to sort out the mess.
Updating from commit id 1c4dbaa0:
2019-11-18 Julius Werner Makefile: Fix typo for MOCK_TPM
to commit id 695c56dc:
2019-12-04 Julius Werner Makefile: Make loop unrolling fully
controllable by the caller
BUG=b:124141368, chromium:1006689
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ia2612da0df101cd3c46151dbce728633a39fada1
Signed-off-by: Joel Kitching <kitching@google.com>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. No gpio control in bootblock
2. Disable power and assert reset in ramstage gpio
3. Power on and then deassert reset at the end of ramstage gpio
4. Disable power and assert reset when entering S5
On "reboot", the amount of time the power is disabled for is
equivalent to the amount of time between triggering #4 and wrapping
around to #3, which is about 400ms on Kohaku.
Since #2 forces power off for FPMCU, S3 resume will still
not work properly.
Additionally, we must ensure that GPP_A12 is reconfigured as an output
before going to any sleep state, since user space could have configured
it to use its native3 function.
See https://review.coreboot.org/c/coreboot/+/32111 for more detail.
The control signals have been validated on a Kohaku in
the following scenarios:
1. Cold startup
2. Issuing a "reboot" command
3. Issuing a "halt -p" and powering back on within 10 seconds
4. Issuing a "halt -p" and powering back on after 10 seconds
5. Entering and leaving S3 (does not work properly)
6. Entering and leaving S0iX
BRANCH=hatch
BUG=b/142751685
TEST=Verify all signals as mentioned above
TEST=reboot
flash_fp_mcu /opt/google/biod/fw/dartmonkey_v2.0.2417-af88cc91a.bin
TEST=halt -p
# power back on within 10 seconds
flash_fp_mcu /opt/google/biod/fw/dartmonkey_v2.0.2417-af88cc91a.bin
TEST=halt -p
# power back on after 10 seconds
flash_fp_mcu /opt/google/biod/fw/dartmonkey_v2.0.2417-af88cc91a.bin
Change-Id: I2e3ff42715611d519677a4256bdd172ec98687f9
Signed-off-by: Craig Hesling <hesling@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch moves the common devicetree settings into baseboard and
creates overridetree.cb for each variant. For PCIe root port settings,
SATA, eMMC, I2Cs and GBe, they are in overridetree.
TEST=build an image for each variant
Change-Id: I067bdb3fcf1218b93e52801f6db093e24d7d2b62
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36794
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Over time our printk() seems to acquire more and more features... which
is nice, but it also makes it a little less robust when something goes
wrong. If the wrong global is trampled by some buffer overflow, it
suddenly doesn't print anymore. It would be nice to have at least some
way to tell that we triggered a real exception in that case.
With this patch, arm64 exceptions will print a '!' straight to the UART
before trying any of the more fancy printk() stuff. It's not much but it
should tell the difference between an exception and a hang and hopefully
help someone dig in the right direction sooner. This violates loglevels
(which is part of the point), but presumably when you have a fatal
exception you shouldn't care about that anymore.
Change-Id: I3b08ab86beaee55263786011caa5588d93bbc720
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37465
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To avoid trampling over interesting exception artifacts on the real
stack, our arm64 systems switch to a separate exception stack when
entering an exception handler. We don't want that to use up too much
SRAM so we just set it to 512 bytes. I mean it just prints a bunch of
registers, how much stack could it need, right?
Quite a bit it turns out. The whole vtxprintf() call stack goes pretty
deep, and aarch64 generally seems to be very generous with stack space.
Just the varargs handling seems to require 128 bytes for some reason,
and the other stuff adds up too. In the end the current implementation
takes 1008 bytes, so bump the exception stack size to 2K to make sure it
fits.
Change-Id: I910be4c5f6b29fae35eb53929c733a1bd4585377
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Arm CPUs have always had an odd feature that allows you to mask not only
true interrupts, but also "external aborts" (memory bus errors from
outside the CPU). CPUs usually have all of these masked after reset,
which we quickly learned was a bad idea back when bringing up the first
arm32 systems in coreboot. Masking external aborts means that if any of
your firmware code does an illegal memory access, you will only see it
once the kernel comes up and unmasks the abort (not when it happens).
Therefore, we always unmask everything in early bootblock assembly code.
When arm64 came around, it had very similar masking bits and we did the
same there, thinking the issue resolved. Unfortunately Arm, in their
ceaseless struggle for more complexity, decided that having a single bit
to control this masking behavior is no longer enough: on AArch64, in
addition to the PSTATE.DAIF bits that are analogous to arm32's CPSR,
there are additional bits in SCR_EL3 that can override the PSTATE
setting for some but not all cases (makes perfect sense, I know...).
When aborts are unmasked in PSTATE, but SCR.EA is not set, then
synchronous external aborts will cause an exception while asynchronous
external aborts will not. It turns out we never intialize SCR in
coreboot and on RK3399 it comes up with all zeroes (even the reserved-1
bits, which is super weird). If you get an asynchronous external abort
in coreboot it will silently hide in the CPU until BL31 enables SCR.EA
before it has its own console handlers registered and silently hangs.
This patch resolves the issue by also initializing SCR to a known good
state early in the bootblock. It also cleans up some bit defintions and
slightly reworks the DAIF unmasking... it doesn't actually make that
much sense to unmask anything before our console and exception handlers
are up. The new code will mask everything until the exception handler is
installed and then unmask it, so that if there was a super early
external abort we could still see it. (Of course there are still dozens
of other processor exceptions that could happen which we have no way to
mask.)
Change-Id: I5266481a7aaf0b72aca8988accb671d92739af6f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The PCH uses the SRCCLKREQ# pin to detect PCIe device in the slot in
order to send clock signal to it. However, this logic is not required
for the Realtek LAN device, since this chip is soldered to the board
and always uses clocking. The chipset can't receive the clock request
signal (most likely this pin isn't connected) and doesn't enable the
CLK. For this reason, the device is broken during the initialization
phase. The patch disables clock request logic for the PCH PCIe port 6
to initialize the onboard LAN device correctly.
Change-Id: I5cbce6177c89052eb50959f43903b6f8a607e77f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36377
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch changes all existing instances of clrsetbits_leXX() to the
new endian-independent clrsetbitsXX(), after double-checking that
they're all in SoC-specific code operating on CPU registers and not
actually trying to make an endian conversion.
This patch was created by running
sed -i -e 's/\([cs][le][rt]bits\)_le\([136][624]\)/\1\2/g'
across the codebase and cleaning up formatting a bit.
Change-Id: I7fc3e736e5fe927da8960fdcd2aae607b62b5ff4
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This patch removes the recently added update8/16/32/64() API and
replaces it with clrsetbits8/16/32/64(). This is more in line with the
existing endian-specific clrsetbits_le16/32/64() functions that have
been used for this task on some platforms already. Rename clrsetbits_8()
to clrsetbits8() to be in line with the new naming.
Keep this stuff in <device/mmio.h> and get rid of <mmio.h> again because
having both is confusing and we seem to have been standardizing on
<device/mmio.h> as the standard arch-independent header that all
platforms should include already.
Also sync libpayload back up with what we have in coreboot. (I'm the
original author of the clrsetbits_le32-definitions so I'm relicensing
them to BSD here.)
Change-Id: Ie4f7b9fdbdf9e8c0174427b4288f79006d56978b
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37432
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All serial I2C bus frequencies should not be over 400KHz in kohaku,
but the measurement showed frequencies of I2C1 and I2C4 were over
400KHz. (b:144885961)
This change adjusts I2C speed settings to limit that frequencies to
400KHz.
The new setting values have been from other projects using same I2C
components, and verified I2C1 and I2C4 frequencies < 400MHz internally.
BUG=b:144885961
BRANCH=firmware-hatch-12672.B
TEST=Verified I2C1 and I2C4 frequency not over 400KHz
Change-Id: I9614fb39b6e55cb2ce1b0879a9f5204e55002f8d
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
All AMD CPU families supported in coreboot have BIOSRAM space. Looking at
the source code, every family could have the same API to save and restore
cbmem top or UMA base and size.
Unify BIOSRAM layout and add implementation for cbmem top and UMA storing.
Also replace the existing implementation of cbmem top and UMA with the
BIOSRAM access.
TEST=boot PC Engines apu1 and apu2
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I69a03e4f01d7fb2ffc9f8b5af73d7e4e7ec027da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37402
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to BKDGs for families 15h 60-6fh or newer and families 16h the
ACPI MMIO decode enable bit is the second LSB, not the first LSB.
Additionally create another enable function for older families where
the register and bit is different.
It does not seem to impact any current board, but may be crucial for
incoming C bootblock implementations when this bit will need to be set
very early. Most likely this bit is set by AGESA right now.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iaa31abc3dbdf77d8513fa83c7415b9a1b7fd266f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37178
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix regression with commit 5639736
binaryPI: Drop CAR teardown without POSTCAR_STAGE
Occassionally (maybe 1 boot in 10) SMP lapic_cpu_init() fails
with following errors in the logs of pcengines/apu2:
CPU 0x03 would not start!
CPU 0x03 did not initialize!
The CPU number is sometimes 0x02, never seen 0x01. Work-around also
suggests something to do with cache coherency and MTRRs that is really
at fault.
As a work-around return the BSP CAR teardown to use wbinvd instead
of invd. These platforms do not support S3 resume so this is the
easy work-around for the time being.
Change-Id: I3dac8785aaf4af5c7c105ec9dd0b95156b7cca21
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch performs below operations:
1. Rename soc_fill_gpio_pm_configuration to soc_gpio_pm_configuration
2. Move soc_gpio_pm_configuration() to gpio_common.c
3. Calling from bootblock and after FSP-S to ensure GPIO PM configuration
is updated with devicetree.cb value even with platform reset.
BUG=b:144002424
TEST=coreboot configures all MISCCFG.bit 0-5 local clock gating based on devicetree.cb
Change-Id: I54061d556d62462d9012bc47bb9f3604a3e5a250
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Remove default path/to/file strings when USE_AMD_BLOBS is not enabled.
This will result in a buildable, but not runable image, in the default
configuration.
Drop the check for HAVE_MERLINFALCON_BINARIES in the path default.
A later patch will address the poor use of this symbol
All PSP blobs are still assumed to be in the same directory as the AMD
public key. Qualify building the amdfw.rom intermediate image and
including it into coreboot.rom on whether the public key remains "".
This change infers it's OK to skip xHCI and GEC firmware too, although
the images normally reside in a separate directory.
This change only determines whether default paths and names exist.
Paths will be updated in a follow-on patch.
Change-Id: Ic21fbd7a58b340a9bcaaea456e1f38b567215b81
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37220
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable ACPI methods to control privacy screen on Drallion devices.
Drallion devices may not have a privacy screen and it is up to the
EC to determine if the privacy screen is present on the system.
BUG=b:142656363
TEST=emerge-drallion coreboot chromeos-bootimage
Change-Id: I79d02bb1b25f0deb49ae4bb852b7ed8c21fd31c7
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36045
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add gfx.asl file for cannonlake SOCs to allow for graphics-related ACPI
devices and methods on cannonlake devices.
BUG=b:142237145
TEST=gfx.asl added to drallion dsdt.asl
Change-Id: I38a26f3135d571e2f9b63840d38fd4d3476fc142
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change allows for Intel graphics devices to use drivers/generic/gfx
driver to populate ACPI SSDT table for common graphics related devices
and methods.
BUG=b:142237145
TEST=On sarien_cml add generic/gfx to the devicetree and device is
enumerated and correct SSDT ASL is observed.
Change-Id: Ibc86a88687ac860ebef19a4b68af64fd50d12b8e
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Since struct vb2_shared_data already contains workbuf_size and
vboot_workbuf_size is never used in depthcharge, remove it from struct
sysinfo_t. In addition, remove lb_vboot_workbuf() and add
CBMEM_ID_VBOOT_WORKBUF pointer to coreboot table with
add_cbmem_pointers(). Parsing of coreboot table in libpayload is
modified accordingly.
BRANCH=none
BUG=chromium:1021452
TEST=emerge-nami coreboot libpayload depthcharge; Akali booted correctly
Change-Id: I890df3ff93fa44ed6d3f9ad05f9c6e49780a8ecb
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
After CB:36808, CB:36844 and CB:36845, all fields except buffer_offset
were removed from struct vboot_working_data. Since buffer_offset is used
to record the offset of the workbuf relative to the whole structure, it
is no longer needed.
This patch removes the structure, and renames vboot_get_working_data()
to vboot_get_workbuf().
BRANCH=none
BUG=chromium:1021452
TEST=emerge-nami coreboot
Change-Id: I304a5e4236f13b1aecd64b88ca5c8fbc1526e592
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Drop the redundant cimx_util, remove the includes when appropriate and
replace the implementation with amdblocks/acpimmio where needed.
TEST=boot PC Engines apu1 and launch Debian with Linux kernel 4.14.50
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I66b1f82926372b6ebb570893b6eb73c7f2935b9d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
In particular:
- Set voltage before enabling regulators
- Enable regulators and the clock without any sleeping in between. There's
no need to wait there.
- Sleep 1 ms in order to wait for regulator voltages settling before
lifting xshutdown.
BUG=chromium:959232
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Change-Id: I0f8857ae369d5038f293a0e2c48c681df535ad86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In particular:
- Enable regulators *after* configuring the voltage
- Allow 1 ms for the voltages to settle
- Enable clock after powering on regulators
- Remove extra delays between enabling things. The sensor requires 8192
clock cycles after the reset is lifted before I²C access, so 1 ms is
enough.
- Make the delay after lifting xshutdown 10 ms. This guarantees that
streaming will only start once the sensor has had enough time to settle
after lifting the reset.
BUG=chromium:959232
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Change-Id: I4589a7d7ec324f4520572a406cc11ad3feec8b21
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36723
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The overhead of pushing variables to stack exceeded the number
of instructions the actual MMIO operation took and the build of
google/aleena with inlined accessors turned out to be just
slightly (<2 KiB) smaller for the entire romstage or ramstage.
Simple read-modify-write MMIO cycles should optimise better now.
IO cycles with index/data register are borderline, at
first sight assembly looked better by not inlining them.
Change-Id: If2c37c9886a0151183aa6dd80eb068d6c67b3848
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
since we support JSL and TGL soc under tigerlake folder, we need to make
sure all soc related files get compiled based on
CONFIG_SOC_INTEL_TIGERLAKE_BASE and not only for Tigerlake.
We can control soc specific file compilation through Kconfig of
individual soc.
Change-Id: I1a663555d0bdf7588c4e12363375e7c90629f7d9
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Working on some other code, I noticed that superio/aspeed was added as
an include path even though I wasn't using it. I investigated and found
that NOTHING is using it. The files in the aspeed directory all
reference files in their own directory.
The supermicro x11-lga1151-series boards are the only ones using this
SIO.
TEST=util/abuild/abuild -t supermicro/x11-lga1151-series
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I377066451a50452c17c9bfaa0f815f69e039984e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
When migrating glados (and variants) to FSP 2.0, the older board-
specific VBTs were dropped in favor of the default FSP 2.0 VBT due to
compatibility issues. Now that libgfxinit is available and the default,
restore the board-specific VBTs so that external displays function
properly. Select MAINBOARD_NO_FSP_GOP for all variants except glados
since FSP/GOP init will not function properly with the older VBTs.
Test: build/boot chell and caroline variants w/libgfxinit, verify
external displays now work again.
Change-Id: If55a67e0d3d78e4acf80cee1733ad8e14b8847d4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add VBT files for Atlas, Nocturne, Rammus, and Soraka variants.
Extracted from ChromeOS recovery images for the respective boards.
Select INTEL_GMA_HAVE_VBT for all variants except Poppy, since
it doesn't have a VBT (or a recovery image from which to extract one).
Change-Id: Icba2741e0b7309c22c027f956cd20cec78f34052
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
These were often used to distinguish CAR_GLOBAL variables that weren't
directly usable. Since we're getting rid of this special case, also get
rid of the marker.
This change was created using coccinelle and the following script:
@match@
type T;
identifier old =~ "^(g_.*|.*_g)$";
@@
old
@script:python global_marker@
old << match.old;
new;
@@
new = old
if old[0:2] == "g_":
new = new[2:]
if new[-2:] == "_g":
new = new[:-2]
coccinelle.new = new
@@
identifier match.old, global_marker.new;
@@
- old
+ new
@@
type T;
identifier match.old, global_marker.new;
@@
- T old;
+ T new;
@@
type T;
identifier match.old, global_marker.new;
@@
- T old
+ T new
= ...;
There were some manual fixups: Some code still uses the global/local
variable naming scheme, so keep g_* there, and some variable names
weren't completely rewritten.
Change-Id: I4936ff9780a0d3ed9b8b539772bc48887f8d5eed
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
SSE2 instructions are supported by family14 and newer.
SSE will be automatically enabled in bootblock_crt0 for platforms that
migrate to C bootblock. Because of that family specific CAR setup may
avoid additional code.
TEST=boot PC Engines apu1 and apu2
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I19f1793112439f0c706ebb066f9807364ad8c5a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37292
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This fixes the following:
- Fix smmstore_read_region to actually read stuff
- Clean up the code a little
- Change the loglevel for non error messages to BIOS_DEBUG
- Use an incoherent rdev to potentially speed up reading access
TESTED on google/wolf with out of tree patch to hook up smmstore to
sb/intel/lynxpoint.
Change-Id: I629be25d2a9b65796ae8f7a700b6bdab57b91b22
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If one wishes to use the functions guarded here, he
has to have datasheet open anyways. It should be clear
from there which regions are supported and which are not.
TEST=Reproducible build of google/aleena.
Change-Id: I0c1f0c9c9a6711532c5078c08cdf9e6612f3bc9c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
This patch does two things:
- The CLI and Git Cola sections contained some duplicated information
about pushing patches, which is now factored out into its own section.
- The draft workflow is now disabled, so that part has been reworded to
describe how to submit a private patch.
Signed-off-by: David Hendricks <david.hendricks@gmail.com>
Change-Id: I562c101ab2ee78d901be7e99165daba7473dc3c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This header was originally copied from the Linux kernel. However, these
days all fixed-width integers are defined in stdint.h, and all of the
other typedefs in this file are kernel-specific and aren't used
anywhere, so we can drop it.
Change-Id: I6ee7acb5e12f4b4b7c4325cedcfee36b93ab6a3d
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
With the persistent vboot context coreboot no longer needs to read GBB
flags from flash itself -- it can just ask vboot for the cached result.
This patch removes the existing GBB code and provides gbb_is_flag_set()
(with a slightly better namespaced name) as a static inline instead.
Change-Id: Ibc3ed0f3fbeb53d630925d47df4dc474b0ed07ee
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Various recent x86 SOCs have trouble registering short pulses
generated by the H1 to indicate that it is ready for the next
transaction.
This patch adds an error message to report this condition, which would
greatly reduce the amount of guesswork when troubleshooting new
platforms.
BUG=b:144002424
TEST=tried this code on the Drallion device exhibiting the problem,
observed error messages in the coreboot log;
$ grep IRQ ap.log
Cr50 i2c TPM IRQ timeout!
Cr50 i2c TPM IRQ timeout!
Cr50 i2c TPM IRQ timeout!
Cr50 i2c TPM IRQ timeout!
...
Change-Id: I5f6ee3986bed58e12fd0ec8cecbf35f46c9263c2
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Add APU names of STONEYRIDGE and MERLINFALCON to Kconfig. The existing
convention of SOC_AMD_PRODUCTNAME_PKG will be phased out.
Don't explicitely use the APU_STONEYRIDGE name yet when creating
default paths. Prairie Falcon relies on the default setting, and this
will be addressed in a later change.
Change-Id: I2061b9b02f6e9def4e151fc38951ad8abb68df1d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
This patch makes below clean-up for report_cpu_info()
function.
1. Remove unused variables.
2. Make fill_processor_name function available in bootblock.
3. Reuse fill_processor_name.
TEST= Succesfully able to boot soraka and verify the
cpu_name "CPU: Intel(R) Pentium(R) CPU 4415Y @ 1.60GHz"
Change-Id: Idf7b04edc3fce147f7856591ce7e5a0cd05f43fe
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36840
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Workaround to disable USB2 PHY power gating to fix issue seen when
Apple 87W USB-C charger is connected in S0ix state on WHL platforms
(based on Intel's recommendation). Issue is seen on CML platforms also.
So, disable power gating for Drallion too.
Add devicetree entry to set the flag to disable USB2 PHY power gating
for different CNL PCH based platforms
BUG=b:133775942
TEST=Connect Apple 87W USB-C charger when the system is in sleep and check if
the system wakes up after that
Signed-off-by: Surendranath Gurivireddy <surendranath.r.gurivireddy@intel.com>
Change-Id: I95909c73de758fccc7f616a330c1e1f0667e8c25
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36519
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The remaining (active) binaryPI boards moved away from
BINARYPI_LEGACY_WRAPPER and have POSTCAR_STAGE now.
As the cache_as_ram.S is also used with AGESA, this slightly
reduces the codesize there for romstage and postcar as well.
This commit is actually a revert for the vendorcode parts,
AMD originally shipped the codes using 'invd' for the CAR
teardown, but these were changed for coreboot due the
convoluted teardown that used to happen with non-empty stack.
Change-Id: I693c104c3aab3be537c00695cbd764a48bd603b0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/18526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per the 4.11 release requirement, CAR_GLOBAL_MIGRATION=n is a
mandatory feature, which most binaryPI boards lack as they
use BINARYPI_LEGACY_WRAPPER.
Disable all binaryPI platforms, except pcengines/apu2, from
the build for the time being. If a platform does not reach
POSTCAR_STAGE=y and C_ENVIRONMENT_BOOTBLOCK=y within a
reasonable timeframe both the mainboard and the respective
unused platform support code will get removed.
Change-Id: Id81ab0f168034187ecf62203b5a33ac6ba49a35d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Adopting the mainboard code to use hooks from state_machine.h.
No post codes are changed, except for those which were explicitly sent in
mainboard/romstage.c. Boot time is reduced by more than 7%, from 5.029s to
4.657s (coreboot timestamps, measured for loglevel 7).
POSTCAR_STAGE is required since coreboot 4.11 release.
TEST=boot PC Engines apu2 and launch Debian Linux with 4.14.50 kernel
Change-Id: Iff3dbe68ac17eb2947ff40b9769c6650255656cf
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
It is a requirement for Firmware to have Firmware Interface Table (FIT),
which contains pointers to each microcode update.
The microcode update is loaded for all logical processors before reset vector.
FSPT_UPD.MicrocodeRegionBase and FSPT_UPD.MicrocodeRegionLength are
input parameters to TempRamInit API.
If these values are 0, FSP will not attempt to update microcode.
Since Gen-4 all IA-SoC has FIT loading ucode even before cpu reset in place
hence skipping FSP-T loading ucode after CPU reset options.
Also removed unused kconfig CONFIG_CPU_MICROCODE_CBFS_LOC and
CONFIG_CPU_MICROCODE_CBFS_LEN
Change-Id: I3a406fa0e2e62e3363c2960e173dc5f5f5ca0455
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37187
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: David Guckian
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch provides options to override descriptor default CPU flex
ratio from coreboot code. cpu_ratio_override to provide the required CPU
ratio.
Note: Don't override the flex ratio if cpu_ratio is 0.
BUG=b:142264107
TEST=Without override flex_ratio is 0 and verified booting to
OS after overriding with flex_ratio value 5.
Change-Id: Ib01650f52f3d402f669e7e7f5b28a648b86f08ec
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
When we only enable XO_SOC and mask most BBLPM requests, the BBLPM HW
arbiter will have DCXO core to enter Baseband Low-Power Mode(BBLPM).
Under BBLPM mode, inaccurate(about 1.5KHz offset) 26MHz clocks from
crystal is provided and crystal voltage will drop from 1.8V to 0.7V
or lower.
In order to ensure the stability by always outputting an accuarate
system clock when system is running. We should disable BBLPM when only
XO_SOC enabled.
BRANCH=kukui
TEST=accurate 26MHz provided and correct crystal voltage swing
Change-Id: Iea72a964507a19735cf92e3774cd8a94c06545b2
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37136
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current code uses CPUID leaf 0x1, EBX bits 16:23 to determine number for
"core count". However, it turns out this number has little to do with
real number of cores. According to SDM vol 2A, it stays for "maximum
number of addressable IDs for logical processors in this physical
package". This does not seem to take into account fusing of giving
processor.
The new code determines 'core count' by dividing thread-level cpus by
reported logical cores. This seems to be the only way to arrive
to number of cores as it is reported in official CPU datasheet.
TEST=tested on OCP monolake
Change-Id: Id4ba9e3079f92ffe38f9104ffcfafe62582dd259
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The old logic only uses the type to identify resources, which makes a
resource in override tree overriding the first resource with the same
type (but possibly different index) in base tree, and resources with
same type (but again different index) in override tree overriding each
other.
Resources had better be identified with both their type and index.
Change-Id: I7cd88905a8d6d1c7c6c03833835df2fba83047ea
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37109
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that the EC software sync in romstage ("early EC sync") patches
have landed, it's time to enable this for Hatch.
BUG=none
BRANCH=hatch
TEST=verify EC sync runs in romstage
Change-Id: Ie567ab081b95b2302b051812fbf46e183c76bab6
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37025
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This fixes issue that became visible after implementing post-CAR stage on
top of `340e4b80904f lib/cbmem_top: Add a common cbmem_top implementation`.
Compilation error was:
Forbidden global variables in romstage:
ffffff00 d top.2205
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Change-Id: I088ac824f9b66387843ae5810fd2c75a8b16d9db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36976
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Binary strings should be joined with a binary string
* Binary files should be opened in binary mode.
* Division that wants truncation should make it explicit.
I have tested that these changes let me compile.
Change-Id: I7c41b80688a9c6bdb3c66561ff531311cc7ebb13
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37024
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Even with four cloc invocations it's faster than doing the rename
dance and messes up the tree less. It also opens up using cloc's git
mode to work on a git tree instead of a checkout.
Change-Id: I3ad8fc6802ecedb332359d00b28ea61c33ed2ea0
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Having the release notes mostly ready one week before the release
allows for better review.
Some statistics, the actual release date and commit ID can only be
filled in on release day, but there's a tried & true technique for
that: placeholders.
It's also a nice touch to have the release notes of a release within
its source tarballs, so push them right before creating the release
(since changes in Documentation/releases won't break coreboot in
any way).
Change-Id: Iad7ba1ba4fc841bf437f2a997428b7f636e15422
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36957
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
3b452e0 "nb/intel/nehalem: Move PCH init to sb/intel/ibexpeak"
introduced a regression where the GAME_L decode range was not set
up, which is used by the WACOM digitizer on the Thinkpad X201T.
Change-Id: Ie569d567a65010aa5372323f8610a1b8b5d2599d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36994
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Kohaku always used the default MEM_STRAPs in hatch baseboard. Adding
explicit configuration for Kohaku in the event that MEM_STRAP is set
differently in the baseboard gpio file.
BUG=b:144895517
BRANCH=hatch
TEST=None
./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I8f7105b3925f17c1741660d84c83c5d15f398a8d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37106
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to IPMI SPEC, it is recommended that BIOS includes provisions
for checking and reporting on the basic health of BMC by executing
the Get Self Test Results command and checking the result.
TEST=Check the result in response data to confirm the BMC status is fine
or not.
Change-Id: I20349cec2e8e9420d177d725de2a5560d354fe47
Signed-off-by: Morgan Jang <Morgan_Jang@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Add VBT file extracted from vendor (AMI) firmware,
use by default to ensure functional display after
resume from S3 when using libgfxinit.
Test: build/boot Librem 13v2/3/4,15v3/4 boards, verify
functional display after resume from S3 when using libgfxinit.
Change-Id: I6bc5dab60e3601d56dae4300efee255d7c58329d
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37068
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch keeps required pch_early_init() function like ABASE programming,
GPE and RTC init into bootblock and moves remaining functions like
TCO configuration and SMBUS init into romstage/pch.c in order to maintain
only required chipset programming for bootblock and verstage.
TEST=Able to build and boot soraka.
Change-Id: Idf7b04edc3fce147f7857591ce7d5a0cd03f43fe
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
This was only used with amdfam10h-15h, where cache
coherency between nodes was supposed to be guaranteed
with this code. We could want a cleaner and more generic
approach for this, possibly utilising .data sections.
Change-Id: I00da5c2b0570c26f2e3bb464274485cc2c08c8f0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This was only used with amdfam10h-15h, and only in romstage
while commentary elsewhere says concurrent CMOS and CBFS
access caused issues.
We would want a cleaner approach on this, if re-implemented.
Change-Id: I8512196cb55ff2b4542b1421a1bbae540450115a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There are four chipsets selecting PMC_GLOBAL_RESET_ENABLE_LOCK but only
one (apollolake) is actually calling the code. Add the missing call.
Also fix the register offset in a comment in reset code.
Tested successfully on X11SSM-F by reading ETR3.
Change-Id: If190c3c66889ede105d958b423b38ebdcb698332
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36573
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make use of the new ETR address API in the ETR3 register related
functions.
Further, disabling and locking of global reset is now done at once to
save one read-modify-write cycle, thus the function was renamed
accordingly and the now redundant disabling in soc/apl got removed.
Change-Id: I49f59efb4a7c7d3d629ac54a7922bbcc8a87714d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a comment to the newly introduced MMIO address helpers for PCI
config registers, that the pointer returned may change during the boot
processs and, thus, must not be cached.
Change-Id: Ieb90ae9d67a3b944d35587dec54756a17c27c86f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add VBT file extracted from vendor (AMI) firmware,
use by default to ensure functional display after
resume from S3 when using libgfxinit.
Test: build/boot Librem 13v1/15v2 boards, verify
functional display after resume from S3 when using libgfxinit.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: I44d75486da3083cd1f07ea82dc18688db84a621e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36916
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Perform EC software sync in romstage, before memory training is started.
Because the ChromeOS EC will not currently perform USB-PD negotiation
until it jumps to running its RW code, this allows the system to get
access to more power earlier in the boot flow.
This is guarded by CONFIG_VBOOT_EARLY_EC_SYNC.
BUG=b:112198832
BRANCH=none
TEST=EC software sync works in update and non-update case.
No significant effect on boot time (~6 ms).
Change-Id: I31f3407a2afcbf288461fab1397f965f025bc07c
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36211
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, depthcharge and coreboot are using two different vboot libraries.
coreboot is using "fwlib20", while depthcharge uses "fwlib". The only
difference between the two libraries is the inclusion of vboot1-only
compilation units in fwlib, which are now deprecated. Therefore, coreboot
may as well use fwlib too. Vboot is expected to converge on a single firmware
library soon.
BUG=none
BRANCH=none
TEST=compiles and runs verstage correctly
Change-Id: I905b781c3596965ec7ef45a2a7eafe15fdd4d9cc
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36341
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add 4 new timestamps to the EC software sync flow:
1) Beginning of EC software sync
2) EC finished calculating Vboot hash
3) EC is no longer requesting power limiting
4) End of EC software sync
BUG=none
BRANCH=none
TEST=verified timestamps show up in cbmem log
Change-Id: I6e5703c146b5ec27d01700fdb39cb3d2092ea8a8
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Use the new functions introduced into the EC driver to support
performing EC software sync via vboot callbacks.
NOTE: This patch assumes that the EC image is added to CBFS
uncompressed. Streaming decompression of the image will be added in a
future patch.
Also adds a new Kconfig option VBOOT_EARLY_EC_SYNC. The new Kconfig
option compiles EC software sync into romstage, dependent upon having a
CrOS EC.
BUG=b:112198832
BRANCH=none
TEST=Successful EC software sync
Change-Id: I9b1458a45ab3ed5623af50f78036c4f88461b226
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36208
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop struct cbfs_props and replace with struct region_device object.
The goal of the cbfs locator APIs are to determine the correct region
device to find the cbfs files. Therefore, start directly using struct
region_device in the cbfs location paths. Update the users of the API
and leverage the default boot region device implementation for
apollolake.
Change-Id: I0158a095cc64c9900d8738f8ffd45ae4040575ea
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Since we already have pre-RAM cache for FMAP (CB:36657), calling
load_firmware() multiple times is no longer a problem. This patch
replaces vboot_get_selected_region() usage with vboot_locate_firmware(),
which locates the firmware by reading from the CBMEM cache.
In addition, returning false from vboot_is_slot_selected() implies the
recovery path was requested, i.e., vb2_shared_data.recovery_reason was
set. Therefore, we simply remove the vboot_is_slot_selected() check from
vboot_check_recovery_request().
BRANCH=none
BUG=chromium:1021452
TEST=emerge-kukui coreboot
Change-Id: I27cb1a2175beb189053fc3e44b17b60aba474bb0
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This also permits removal of vc/amd/agesa/f12, as it was the only
mainboard using it. That will in turn allow resolving some unique
Coverity issues reported against that source.
Change-Id: I73f570f01fcb5ba0e306508a569ea97f432596b3
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The MIPS architecture port has been added 5+ years ago in order to
support a Chrome OS project that ended up going nowhere. No other board
has used it since and nobody is still willing or has the expertise and
hardware to maintain it. We have decided that it has become too much of
a mainenance burden and the chance of anyone ever reviving it seems too
slim at this point. This patch eliminates all MIPS code and
MIPS-specific hacks.
Change-Id: I5e49451cd055bbab0a15dcae5f53e0172e6e2ebe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34919
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fill in some stats using our repo analysis scripts in
util/release/, thank the contributors, add some prose
about notable achievements since 4.10.
Also start a new doc for 4.12.
Change-Id: I10a39081762d6e01f4040f717d36662975e4c8e9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36948
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Run
- make -C util/docker doc.coreboot.org to build the docker image
- make -C util/docker docker-build-docs to build the documentation
- make -C docker-livehtml-docs to serve autoupdated documentation over
http://0.0.0.0:8000
Change-Id: Ic07f216f8d90d6e212383250b852dc91575304c3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36104
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This config is a slightly stripped configuration of the Chromium OS
configuration used in production. Apparently the bootblock fills up
faster than usual on this device, resulting in address overflows.
Add this config here so we'll notice early in the future.
Change-Id: I3145bba63d32ddb9d00fd98d3cb774bf9ddd69a6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36923
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
By removing this code, we get approximately back to
where the board was before the fmap cache feature
was added, which is small enough for the Chromium OS
default configuration for the board to fit into the
32KB that the bootblock can use on the chipset again.
Change-Id: I52c0c30a14929913ded144bf086c12938e9c2699
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Correct what looks to be errant characters in the makefile variable for
the Gigabit Ethernet Controller. This should have no effect on any
mainboards as none select the HUDSON_GEC_FWM symbol.
Change-Id: Icb861d872973aaf2b653440cae00057d5ad89b20
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Due to the way CAR teardown is handled in FSP 1.0, the results of
car_get_var_ptr() aren't always reliable, which can break things when
running with FMAP cache. It might be possible to fix this but would make
the code rather complicated, so let's just disable the feature on these
platforms and hope they die out soon.
Also allow this option to be used by platforms that don't have space for
the cache and want to save a little more code.
Change-Id: I7ffb1b8b08a7ca3fe8d53dc827e2c8521da064c7
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
With GCC 9.x has a new warning *address-of-packed-member*.
> -Waddress-of-packed-member
>
> Warn when the address of packed member of struct or union is
> taken, which usually results in an unaligned pointer value.
> This is enabled by default.
This results in the build errors below, for example, with GCC 9.2 from
Debian Sid/unstable.
src/southbridge/intel/common/spi.c: In function 'spi_init':
src/southbridge/intel/common/spi.c:298:19: error: taking address of packed member of 'struct ich7_spi_regs' may result in an unaligned pointer value [-Werror=address-of-packed-member]
298 | cntlr->optype = &ich7_spi->optype;
| ^~~~~~~~~~~~~~~~~
Therefore, explicitly disable the warning.
Change-Id: I01d0dcdd0f8252ab65b91f40bb5f5c5e8177a293
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36940
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch moves the traditional POSIX stdbool.h definitions out from
stdint.h into their own file. This helps for using these definitions in
commonlib code which may be compiled in different environments. For
coreboot everything should chain-include this stuff via types.h anyway
so nothing should change.
Change-Id: Ic8d52be80b64d8e9564f3aee8975cb25e4c187f5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch changes the ipq40xx Makefile.inc to follow established
coreboot practice of calling Python scripts directly rather than
invoking the 'python' interpreter explicitly. This has the added effect
of honoring the scripts shebang (which in this case is set to
'python2').
Change-Id: If96e8313527c411ef1bb6386e03b6a209c750131
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some types of Undefined Behavior can be determined statically at compile
time and gcc now has a set of flags that make it emit warnings in that
case instead of doing the __builtin_trap() / optimize / UD2-opcode dance
that silently breaks the resulting binary.
BUG=chromium:958270
BRANCH=none
TEST=abuild passes (probably not)
Change-Id: I3aa5ca00c9838cc7517160069310a1ef85372027
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Some Sandy Bridge boards disabled the PCI-to-PCI bridge early to avoid
probing by the MRC. We can do that for all boards instead, based on the
devicetree setting.
Change-Id: Ie64774628fde77db2a379bdba6a921a31e52fa0d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The integrated GbE port is toggled via the Backed-Up Control (BUC)
register. We already disable it according to the devicetree setting
but never enabled it. This could lead to the confusing situation
that it was disabled before (different build, vendor BIOS, etc.)
but shouldn't be anymore.
As we need a full reset after enabling GbE, do it in early PCH init.
Change-Id: I9db3d1923684b938d2c9f5b369b0953570c7fc15
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Don't overwrite the LPC decode config of the generic PCH code, move
UART init into bootblock_mainboard_early_init() and don't enable the
IOAPIC, which is already done by generic code.
Change-Id: I90d090f5bff29174e68981fea3c3f04c666b1d28
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This bit is used to indicate xHCI routing across reboots. If anything,
coreboot should act on it, not set it during boot. ASL code would be
supposed to set it.
Change-Id: Id14647ac4e591cfa042ca8aad6dfc6ccda35c74a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The generic PCH code already enables a superset of LPC decoding. Move
UART setup to bootblock_mainboard_early_init() where it is expected.
Last but not least, remove an odd write to BUCs (RCBA+0x3414) and
beyond, as it's an 8-bit register and shouldn't be bluntly zeroed.
Change-Id: I24a4ccf6a529460a83f48522d2e05e6ad6614f81
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
mainboard_pch_lpc_setup() and mainboard_late_rcba_config() did 4
things here on top of the generic PCH code:
1. Enabling LPC decoding for gameports. It seems unlikely
that anything is using these ports and there is no code
to support gameports.
2. Decoding of COM3 instead of COM2. What COM?
3. Premature locking of ETR3/global reset. Bad idea.
4. Disabling the GbE port in BUC. Already done by PCH code.
Change-Id: Ie92dbf5c6813435995c4d24ed807ffc8d125953a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
There is some overlap between romstage and bootblock.
LPC setup and BAR initialization is now done twice.
The rationale is that the romstage should not depend too
much on the bootblock, since it can reside in a RO fmap
region.
Enabling the console will be done in a followup patch.
Change-Id: I4d0ba29111a5df6f19033f5ce95adcc0d9adc1fd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The romstage default is to set stack guards at 0x2000 below end
of stack. The code is now overwrites some of the stack guards
so increase the stack size to a comfortable 0x2800.
Change-Id: I91f559383a987241b343e743d11291f2c100f7f5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This also changes the name to mainboard_pch_lpc_setup to better
reflect that it is an optional mainboard hook.
This adds an empty weakly linked default. The rationale behind this
change is that without an implementation of the hook some features
might not work but that the result is likely still able to boot, so it
can be made optional.
Change-Id: Ie8e6056b4c4aed3739d2d12b4224de36fe217189
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This also changes the name to mainboard_late_rcba_config to better
reflect what it does.
This adds an empty weakly linked default. The rationale behind this
change is that without an implementation of the hook some features
might not work but that the result is likely still able to boot, so it
can be made optional.
Change-Id: I1897d0f5ca7427d304a425f5256cd43c088ff936
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This adds an empty weakly linked default. The rationale behind this
change is that without the callback some features might not work
but that the result is likely still able to boot, so it can be made
optional.
Change-Id: I62c8010aa81fc45d208e9293feb2f45b45f34a82
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
In order to always show the bootlogo very early in coreboot we need the
option to always enable the display when VBOOT is enabled.
To do this a config option is added to make sure this functionality can
be provided without interfering with systems that require the standard
VBOOT display handing.
BUG=N/A
TEST=tested on facebook fbg1701.
Change-Id: I3ffaac85d2082717bb9608d536f7cec66a583789
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Some special keys emit a prefix scan code 0xE0. We will ignore all
these except for the power button, F12 and cursor keys on drallion.
Media key mapping is set in depthcharge and will be sent to libpayload
keyboard driver. Whichever board requires this change will update its own
media key mapping.
BUG🅱️139511038
TEST=boot in recovery mode, press F12 to go to diagnostic mode and power
button to confirm. Also in recovery mode left arrow, right arrow, up arrow,
down arrow changes the language on the firmware screen.
Change-Id: I1c11939d18391bebe53ca21cf33a096ba369cd56
Signed-off-by: Thejaswani Putta <thejaswani.putta@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36654
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Leave more space for PreRAM memconsole especially for seeing complete
logs when doing DRAM full calibration (that outputs in 200+k to UART):
- Shrink Full-K mem space (the ELF blob today needs ~132K)
- Move PRERAM_CBFS_CACHE to L2C since it's no used after DRAM is up
- Shrink TIMESTAMP to 1k (all other non-MTK ARM SOCs use only 1k)
- Incease PRERAM_CBMEM_CONSOLE to 63k-4
- Reordered few sections to align at better locations
BUG=b:144542023
TEST=emerge-kukui coreboot chromeos-bootimage; boot and see logs
Change-Id: I8696fb01653c0a581cf62e687dc523cb6fed9a32
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The eltan security items ended up in the chipset menu which is not
desired. Now the eltan security option (when enabled in mainboard) shows
up in the security menu.
BUG=N/A
TEST=build
Change-Id: I3b2aa3836e8d9a3242c6d1f3ba7b7821a5cfb9d3
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
These mainboard don't feature a SPI flash. The SPI init code
will timeout on probing for a SPI flash which takes a lot of time.
Not including all SPI drivers also lightens the uncompressed ramstage
of about 17K or 7K compressed.
Change-Id: Icc7bf62d56fc2ef38854402e658830b8d59c737f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36870
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id e561c63:
2019-10-02 17:03:58 +0530 - (lib: Fix coldboot race condition observed on emulators/simulators)
to commit id 215421c:
2019-11-11 16:40:34 -0800 - (lib: Remove date and time from init message)
This brings in 13 new commits and allows reproducible builds with
opensbi.
Change-Id: I0fb9e0921b017822defa8b56df5a0f3e014d7f33
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The verified_boot_check_cbfsfile() will now try to allocate a buffer from
bootmem if the item in the list has the VERIFIED_BOOT_COPY_BLOCK attribute
set. For large payloads this speeds up the hash operation.
BUG=N/A
TEST=build
Change-Id: Ifa0c93632c59d05ae6d32f8785009a3c3568abc5
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
vboot_possibly_executed previously provided some better
compile-time code elimination, before CB:32716 made
vboot_logic_executed capable of that directly.
BUG=b:124141368,
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: If5ca8f03c51e1ced20e1215b1cfdde54da3d001f
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36863
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The old code stumbled when the whole first group of root ports
was disabled and also made the (sometimes wrong) assumption
that FSP would only hide function 0 if we explicitly told it
to disable it.
Change-Id: Ia6938ca6929c6d9d0293c4f0f0421e38bf53fb55
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36702
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Most of the current implementations for FSP-based platforms
make (sometimes wrong) assumptions how FSP reorders root ports
and what is specified in the devicetree. We don't have to make
assumptions though, and can read the root-port number from the
PCIe link capapilities (LCAP) instead. This is also what we do
in ASL code for years already.
This new implementation acts solely on information read from
the PCI config space. In a first round, we scan all possible
DEVFNs and store which root port has that DEVFN now. Then, we
walk through the devicetree that still only knows devices that
were originally mentioned in `devicetree.cb`, update device
paths and unlink vanished devices.
To be most compatible, we work with the following constraints:
o Use only standard PCI config registers.
o Most notable, don't try to read the registers that
configure the function numbers. FSP has undocumented
ways to block access to non-standard registers.
o Don't make assumptions what function is assigned to
hidden devices.
The following assumptions were made, though:
o The absolute root-port numbering as documented in
datasheets matches what is read from LCAP.
o This numbering doesn't contain any gaps.
o Original root-port function numbers below a PCI
device start at function zero and also don't
contain any gaps.
Change-Id: Ib17d2b6fd34608603db3936d638bdf5acb46d717
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35985
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds 3 mb romstage callbacks:
- void mb_lpc_setup(void) to be used to set up the superio
- void mb_get_spd_map(u8 spd_map[4]) to get I2C addresses of SPDs
- (optional)mb_pre_raminit_setup(int s3_resume) to set up mainboard
specific things before the raminit.
Change-Id: Ic3b838856b3076ed05eeeea7c0656c2078462272
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36758
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On mainboards without DPTF_TSRX_SENSOR_ID method DTRP is never called
Only add the DTRP method when at least one sensor is enabled.
BUG=N/A
TEST=build
Change-Id: I4fb26d5bbb7b334e759e7073b680f830f412467e
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36856
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIOs related to power sequnce are
GPIO_67 - EN_PP3300
GPIO_117 - FULL_CARD_POWER_ON_OFF
GPIO_161 - PLT_RST_LTE_L
1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161
2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67
3. Power reset:
- keep GPIO_67 and GPIO_117 high and
- pull down GPIO_161 for 30ms then release it.
BUG=b:144327240
BRANCH=octopus
TEST=build image and verify on the DUT with LTE DB.
Change-Id: I68b71425391eda1e92806fecdb9c8dcd54f0b95a
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36771
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Changed the order of the verify lists and updated the comments to
reflect the order of execution. This makes the list easier to understand
and maintain.
BUG=N/A
TEST=tested on fbg1701
Change-Id: Ia656fbf07e5d42bafd328eaba69b660e5a1e4f1a
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36817
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Cleanup of the prog_locate_hook routine so the actual coreboot flow is
more clearly reflected in the code.
Remove logging that is not really needed.
BUG=N/A
TEST=tested on fbg1701
Change-Id: Iab6c75beac35d043d296336021c0bce1f828cf34
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36846
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The prepare functionality will be removed from cbfs support and the
eltan verified boot is the only software using it. This is not really
required as we can use the prog_locate_hook() for this functionality.
BUG=N/A
TEST=tested on fbg1701
Change-Id: I189cbad4b24bbbb0840ce6100c89a42a327c5456
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36821
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
The bootblock measurement was handled using the romstage_verify_list()
and the public_key in the mb_log_list. This is confusing as these are
both read-only items that should be handled in the same way.
Both will be handled in the romstage_verify_list().
BUG=N/A
TEST=tested on fbg1701
Change-Id: If05198deec85188f39a221a8b755798755afa5bb
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
When CB:33068 disabled the bootblock console on RK3288, it saved a
whooping 7K of SRAM, but it didn't readjust the stage boundaries to
spread that bounty evenly. This patch moves 4K of free space from the
bootblock to verstage/romstage to allow for future expansion.
Change-Id: I68a09ba80bde0d4f17fba1f7b38c63b7cf2a4672
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
An empty submenu Intel is displayed in security menu when INTEL_TXT is
disabled.
Enable submenu Intel only when INTEL_TXT is enabled.
BUG=N/A
TEST=build
Change-Id: Iff1d84ff60a15259b60c6205a63a27ecb26346a3
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Support to display a logo using FSP 1.1 currently resides in facebook fbg1701
mainboard.
The related support is moved to drivers/intel/fsp1_1 and used by the
Facebook fbg1701 mainboard. The storage for the uncompressed logo
is changed. We don't use .bss any longer as the logo doesn't need to be
available at runtime.
BUG=N/A
TEST=booting Facebook fbg1701
Change-Id: I276e6e14fc87d0b95fe5fdf7b617afd26769de79
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Updating from commit id b2c8984d:
2019-10-01 06:01:59 +0000 - (vboot: fix compile error with MOCK_TPM)
to commit id 87276ffe:
2019-11-07 17:46:09 +0800 - (futility: updater: Clean up hard-coded section names to preserve)
This brings in 48 new commits.
Change-Id: Iabaadc63227b856d0a2b7f3b23fe8c41b28d8eae
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The northbridge code to set up DMI is not correct and the CIR bits
relate to that.
This fixes a regression caused by 2437fe9 'sb/intel/i82801gx: Move CIR
init to a common place', where payloads hang on southbridge IO.
Change-Id: Iabb54d9954d442a1a7b48a6c6e76faa8079a4c71
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36809
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove some of the code duplication on i82801gx.
x4x boards are left untouched for now since that northbridge
also supports i82801jx.
The order of some things has changed:
- on i945 early_ich7_init is now done before the raminit
- enabling the IOAPIC is done before the raminit
Change-Id: Ie39549938891e17667a8819b49a78b9c71c8ec9e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36754
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The CBFS master header is a legacy structure that just conveys the same
information we already have from the FMAP these days. We're still
including it to support older CBFS implementations in some payloads, but
there's no need for coreboot itself to follow this indirection anymore.
This patch simplifies the default CBFS locator to just return the CBFS
offset and size from the FMAP directly.
Change-Id: I6b00dd7f276364d62fa1f637efbaee0e80607c49
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36688
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds an optional pre-RAM cache for the FMAP which most
platforms should be able to use, complementing the recently added
post-RAM FMAP cache in CBMEM. vboot systems currently read the FMAP
about half a dozen times from flash in verstage, which will all be
coalesced into a single read with this patch. It will also help
future vboot improvements since when FMAP reads become "free" vboot
doesn't need to keep track of so much information separately.
In order to make sure we have a single, well-defined point where the new
cache is first initialized, eliminate the build-time hardcoding of the
CBFS section offsets, so that all CBFS accesses explicitly read the
FMAP.
Add FMAP_CACHEs to all platforms that can afford it (other than the
RISC-V things where I have no idea how they work), trying to take the
space from things that look like they were oversized anyway (pre-RAM
consoles and CBFS caches).
Change-Id: I2820436776ef620bdc4481b5cd4b6957764248ea
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Joel Kitching <kitching@google.com>
This patch makes the CBFS default locator .locate() callback externally
available so that code which overrides cbfs_master_header_locator can
reuse or wrap it and doesn't have to copy&paste the whole thing. Use it
for the Eltan vendorcode implementation which previously did this.
Change-Id: I54dad5c8ea64ea0fc472217e275daa815736991e
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36797
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All stages on this board are very close to the limit, so enable
RETURN_FROM_VERSTAGE so that we can overlap verstage and romstage to
use the available SRAM more effectively. (Coincidentally, this also
reduces verstage size quite a bit... maybe we should consider just
making this the default at some point, there are really no downsides.)
Change-Id: I2b91fd13d147f964bcbd7b2850f8a0931ea060df
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch replaces and cleans up the redundant PTN3460 driver files in
/mainboard/siemens directories by using the now available driver in
src/drivers/i2c/ptn3460 and providing mainboard specific functions to
the driver.
TEST=Display is working on Siemens mainboards (e.g. mc_tcu3, mc_apl1, ...).
Change-Id: I976a502e7176a356bab772758250db3cdff529b9
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36643
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch provides a chip driver for the DP-2-LVDS bridge PTN3460.
The bridge is configured via I2C. As the mainboard has all the
information regarding the attached LCD type, there are three hooks into
mainboard code to get the information like EDID data and PTN config.
TEST=Display is working on Siemens mainboards (e.g. mc_tcu3, mc_apl1, ...).
Change-Id: Ie4c8176cd16836fa5b8fd2f72faf7a55723b82f6
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
When 'make clean' is executed and there is no source code cloned for
GRUB2 in payloads/external/GRUB2/grub2 (so GRUB2 has never been used on
this tree) an error message is thrown:
"fatal: cannot change to 'grub2': No such file or directory"
This error happens when there is no grub2 directory and is caused by
line 20 in payloads/external/GRUB2/Makefile where a shell command is
used to check the state of the git repo for grub2. Thought the target
for this code (checkout) is not executed by 'make clean' the shell
evaluates the command as part of the Makefile sourcing and encounters a
missing directory.
This patch fixes this error by checking for the project directory before
the git status of the repo is evaluated.
Change-Id: Ieaa919e1ee5ec2a1ec3c840fa07a6ec16d230e88
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Discussed in CB:36093, in the past many lenovo boards need to declare
an empty h8_mainboard_init_dock() to satisfy h8.c.
Now the confusing H8_DOCK_EARLY_INIT might be retired, and if a
mainboard needs dock init (done with h8_mainboard_init_dock() in the
past) in ramstage, (discussed in CB:4294 where H8_DOCK_EARLY_INIT is
introduced) it can just do it in its own chip_ops.enable_dev function.
Tested on X200. Testing on other affected targets may be necessary.
Change-Id: I5737406d1f6cb6e91b2e2fa349a206a3dba988d1
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Don't select the VBOOT fmap as default if VBOOT is disabled.
Fixes a regression introduced by f8251b98
"mb/emulation/qemu: Add VBOOT support" where the default Kconfig settings
wouldn't allow the qemu boards to run.
Also fix the Supermicro x11-lga1151 series boards.
Change-Id: I90414e2cc7e4c4a6ad67014bd4a7f9c8ff4da389
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36707
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The common cbmem_top_chipset implementation uses the FSP bootloader HOB,
thus move it to the fsp driver which is a more appropriate place.
Change-Id: I914df51a7414eb72416f816ff8375a13d5716925
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36620
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: David Guckian
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In some case where the flash space is limited or when a large payload such as LinuxBoot
is used, the RO region may not be large enough to contain all components that would
normally be added.
This patch adds the possibility to add specific components to the RW regions only in
the same way as the RO_ONLY_SUPPORT does for the RO region.
Please note: this applies only to the items that would normally be added to all regions.
If the payload is directed to the RW region only, a recovery payload needs to be added
to the RO region manually.
BUG=N/A
TEST=build
Change-Id: Ie0df9b5dfc6df4f24efc5582a1aec9ecfb48c44d
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36544
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds a new mainboard variant called mc_apl6 which is based
on mc_apl3. So far only the names have been adjusted with no further
changes. Following commits will introduce the needed changes for this
mainboard variant.
Change-Id: Ic935f6cc1f037947b2c167696d40da8309e4d4f0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
RK3288 is running out of space again. I believe reducing the CBFS cache
size this much should be safe. I don't really care to test it either
though. We should probably just deprecate that SoC at some point, it's
just causing too much pain.
Change-Id: Id8f971606a7a183d3e9af8bbb1b353e518ec24c8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Joel Kitching <kitching@google.com>
With the 0.71586+ Goodix FW, we can reduce the reset delay from 500ms
to 120ms. We should do the change in coreboot device tree after we
ensure Helios DVT build is flashed with 0.71586+ Goodix FW.
BUG=b:142316026
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I000ee4ea84c598b437992f1000f6e5b561cae605
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Provide region_device_end() and make region_end() publically available
for use to match a pattern of open coding the offset + size calculation
for both struct region and struct region_device. Apply the use of the
helpers where the usage matches in the code.
Change-Id: Iaef5d007eef9a77f7f33b0e89298abef0197352d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36689
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of open coding an offset of 0 and querying the size of a
region device provide a rdev_chain_full() helper function that
does that for the caller. For the existing users that match this pattern
convert them to using rdev_chain_full().
Change-Id: Ie316790a8a5b16a7f7e22f86f58bd2e633c19450
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36683
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The FSP loops through microcode updates and at the end checks if
the microcode revision is not zero. Since we update the microcode
before loading FSP, this is the case and a fake microcode can be
passed to the FSP.
The advantage is that the Kconfig symbols to specify the location and
the size of the microcode blob can be dropped.
Change-Id: I63cfb7b19e9795da85566733fb4c1ff989e85d03
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36255
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The google FSP Braswell version has broken microcode update code and
FSP checks at some point if the installed microcode version is non
zero, so coreboot has to update it before calling FSP-T.
This is fixed with newer FSP releases by Intel, but doing updates in
coreboot won't hurt.
Tested with both Intel FSP and google FSP.
Change-Id: I3e81329854e823dc66fec191adbed617bb37d649
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36198
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This hook is unused and with the need for initializing storage to
share cbmem_top over other stages gone, there is likely no future
need for this.
Change-Id: I4ba9daea61b6d7b8949bbd2c4fb71d0a0fa20d93
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Saving cbmem_top across stages is not needed anymore so EBDA should
not be used. The guard to cbmem_top_chipset implementation was
inappropriate.
Change-Id: Ibbb3534b88de4f7b6fc39675a77461265605e56e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
All targets now have the _cbmem_top_ptr symbol populated via calling
arguments or in the nvidia/tegra210 case worked around by populating
it with cbmem_top_chipset explicitly at the start of ramstage, so the
Kconfig guarding this behavior can be removed.
Change-Id: Ie7467629e58700e4d29f6e735840c22ed687f880
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36422
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We generally do not guard source in attempts to reduce
the final object sizes, but rely on garbage collection.
Most of the __unused attributes inserted here will be
removed when remaining __SIMPLE_DEVICE__ guards can
be removed.
Change-Id: I2440931fab4f41d7e8249c082e6c9b5a9cd0ef13
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36641
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested, working:
- First dimm slot of each channel
- USB, SATA
- CPU FSB at 800, 1067 and 1333MHz
- Libgfxinit on DVI and VGA slot
- PCI slot
- Realtek NIC (configure MAC address in Kconfig)
- PEG slot
- PS2 keyboard
Tested, not working:
- second dimm slot for each channel. Those are hooked up to the second
rank of the channel, instead of rank 3 and 4. The raminit does not
support such setups.
Untested:
- PCIe x1 slot, likely works fine
- HDMI
Tested using SeaBIOS 1.12, Linux 4.19.
Change-Id: I88fe9c66dae079cd7eedcc9736c5922defbc0e5a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Clone entirely from Icelake
List of changes on top off initial icelake clone
1. Removed Descriptor Name for Memory mapped SPI flash and
local APIC in northbridge.asl
2. Rearranged code in gpio.asl to move RBUF object under _CRS
and made the file use ASL2.0 syntax.
3. Make use of absolute path for scs.asl
4. Remove unused smbus.asl
5. Rearranged code in nothbridge.asl to move MCRS object under _CRS,
use absolute variable path and added TODO for further clean up.
6. Refer absolute variable path in scs.asl
Change-Id: If967cb5904f543ce21eb6e89421df0e5673d2238
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Clone entirely from Icelake
List of changes on top off initial icelake clone
1. Replace "Icelake" with "Tigerlake"
2. Replace "icl" with "tgl"
3. Replace "icp" with "tgp"
4. Rename structure based on Icelake with Tigerlake
5. Remove and clean below files
5.a Clean up upd override in fsp_params.c,
will be added once FSP available.
5.b Remove __weak functions from fsp_params.c
5.c Remove dGPU over PCIE enable Kconfig option
6. Add CPU/PCH/SA EDS document number and chapter number
7. Remove unnecessary headers from .c files based on review
Tiger Lake specific changes will follow in subsequent patches.
1. Include GPIO controller delta over ICL
2. FSP-S related UPD overrides as applicable
Change-Id: Id95e2fa9b7a7c6b3b9233d2c438b25a6c4904bbb
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36087
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clone entirely from Icelake
List of changes on top off initial icelake clone
1. Replace "Icelake" with "Tigerlake"
2. Replace "icl" with "tgl"
3. Replace "icp" with "tgp"
4. Rename structure based on Icelake with Tigerlake
5. Remove and clean below files
5.a Clean up upd override in fsp_params.c,
will be added once FSP available.
5.b Remove __weak functions from fsp_params.c
6. Add CPU/PCH/SA EDS document number and chapter number
7. Add required headers into include/soc/ from ICL directory
Change-Id: I24980c196efb2c5569996ca4fb315c256cf9de87
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36552
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clone entirely from Icelake
List of changes on top off initial icelake clone
1. Replace "Icelake" with "Tigerlake"
2. Replace "icl" with "tgl"
3. Replace "icp" with "tgp"
4. Rename structure based on Icelake with Tigerlake
5. Add CPU/PCH/SA EDS document number and chapter number
6. Add required headers into include/soc/ from ICL directory
Tiger Lake specific changes will follow in subsequent patches.
1. Add Tigerlake specific device IDs (CPU/PCH/SA)
Change-Id: Id7a05f4b183028550d805f02a8078ab69862a62e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Enable vendorcode measured and verified boot.
Use VBOOT test key for VENDORCODE_ELTAN_VBOOT_KEY_FILE
BUG=N/A
TEST=booting Embedded Linux 4.20 kernel on Facebook FBG1701
Change-Id: Ia2cb3bb873b2d5e7e9031e5b249d86605d8e0945
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The commit 8fc523e3 (drivers/intel/fsp2_0: Use strip_quotes for cbfs
filenames) breaks the Siemens APL mainboards as FSP-M never returns once
it is called. The reason for this is that the -b option is missing when
adding the FSP package to cbfs via cbfstool.
This patch fixes this issue.
TEST=tested on siemens/mc_apl5
Change-Id: I48e5fa36e1ad799d09714f53a3041f73b8ec3550
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36645
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: David Guckian
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch keeps required pch_early_init() function like ABASE programming,
GPE and RTC init into bootblock and moves remaining functions like
TCO configuration and SMBUS init into romstage/pch.c in order to maintain
only required chipset programming for bootblock and verstage.
TEST=Able to build and boot ICL DE system.
Change-Id: I4f0914242c3215f6bf76e41c468f544361a740d8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36627
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With this change cbfs_boot_locate will check the RO (COREBOOT) region if
a file can not be found in the active RW region. By doing so it is not
required to duplicate static files that are not intended to be updated
to the RW regions.
The coreboot image can still be updated by adding the file to the RW
region.
This change is intended to support VBOOT on systems with a small flash
device.
BUG=N/A
TEST=tested on facebook fbg1701
Change-Id: I81ceaf927280cef9a3f09621c796c451e9115211
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36545
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Not all Rangeley SKUs have a fixed 100MHz BCLK.
As per BIOS Writer's Guide, BCLK is available in MSR_FSB_FREQ 0xCD[1:0].
Using fixed BCLK was causing wrong values of core frequencies in _PSS table
for SKUs that do not have BCLK=100MHz.
Change-Id: Id8e0244fab0283b74870950cb00a95aab2a7201f
Signed-off-by: Hannah Williams <hannah.williams@dell.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35348
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All Hatch variants so far embed static SPD data encoded within the
firmware image. However we wish the flexibility for romstage
implementations that allow for reading the SPD data dynamically over
SMBus. This romstage variant allows for reading the SPD data over
SMBus.
V.2: Dispence with memcpy().
V.3: Revert back to previous patch with memcpy().
V.4: Rewrite again to avoid memcpy().
BRANCH=none
BUG=b:143134702
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I3516a46b91840a9f6d1f4cffb2553d939d79cda2
Signed-off-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36449
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The previous values do not affect the touchscreen function. But, the
previous values cause the power leakage in S0ix.
from b/142368161:
1. Modify GPP_D: The specification define T1 >= 10ms. We change it to
12ms for a safety and low impact value in our mind. Enable pin as
GPP_D9 is define to be AVDD in specification. Set it to 10ms to
make it to be the final one to pull low during power off sequence .
2. Add GPP_C4: If we set stop_off_delay_ms to be 1. The true T4 we
got will be 300us . Set stop_off_delay_ms to be 2 . True T4 will be
500us . So we change it to 5 to be a low impact value in our mind
according to the true T4 value we got .
BUG=b:142368161
BRANCH=Master
TEST=emerge-hatch coreboot chromeos-bootimage
./util/abuild/abuild -p none -t google/hatch -x -a
Signed-off-by: YenLu Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I86c920ff1d5c0b510adde8a37f60003072d5f4e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35907
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drallion can be either a clamshell or convertible depending on the
presence of the 360 sensor board. Set the smbios type 3 enclosure type
to either CONVERTIBLE or LAPTOP accordingly.
BUG=b:143701965
TEST='dmidecode -t 3'
Type = Convertible with sensor board connected
Type = Laptop with sensor board disconnected
Change-Id: I766e9a4b22a490bc8252670a06504437e82f72d5
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36512
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's only used for romstage and is incompatible to ramstages. The latter
get `cbmem_top` passed as a third argument now.
Also drop comments that don't apply to this file anymore.
Change-Id: Ibabb022860f5d141ab35922f30e856da8473b529
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
All Hatch variants so far embed static SPD data encoded within the
firmware image. However we wish the flexibility for romstage
implementations that allow for reading the SPD data dynamically over
SMBus.
BRANCH=none
BUG=b:143134702
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: Ie1637d08cdd85bc8d7c3b6f2d6f386d0e0c6589b
Signed-off-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Icelake default selects PLATFORM_USES_FSP2_1 which means stack will be shared
between FSP and coreboot (CONFIG_FSP_USES_CB_STACK) hence no need to have any
other guard to assign FSP_TEMP_RAM_SIZE.
Change-Id: Idbe393f7a63ad10f1ad3c9e7248593cf8eb115d9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36628
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update thermal threshold settings for TSR3 sensor. There is an issue
fan is always running, even during system idle state. This change
fixes this issue and fan starts only when it breaches the temperature
threshold.
BRANCH=None
BUG=b:143861559
TEST=Built and tested on Helios system
Change-Id: Ia417f8c51442005cc8c2251c188cebc197e0a773
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36609
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The quotes were not stripped for the cbfs filenames of the FSP
components. This is causing problems when the regions-for-file macro is
executed (when VBOOT is enabled and the files should be filtered).
BUG=N/A
TEST=build
Change-Id: I14267502cfab5308d3874a0c0fd18a71b08bb9f8
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36548
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When prog_locate() is called in the stage VBOOT is starting from and the
image to be loaded is not the target image vboot_prepare() may be called
too early.
To prevent this vboot_prepare() is removed from the vboot_locator
structure. This allows more control over the start of the vboot logic.
To clarify the change the vboot_prepare() has been renamed to
vboot_run_logic() and calls to initialize vboot have been added at the
following places:
postcar_loader: when VBOOT starts in ROMSTAGE
romstage_loader: when VBOOT starts in BOOTBLOCK
ramstage_loader: when VBOOT starts in ROMSTAGE
BUG=N/A
TEST=tested on facebook fbg1701
Change-Id: Id5e8fd78458c09dd3896bfd142bd49c2c3d686df
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36543
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Align the eltan mboot support with coreboot tpm support to limit the amount of custom code.
We now only support SHA256 pcrs, only single a single digest will be handled in a call.
The pcr invalidation has been changed fixed values are now loaded while the correct algortihm is
selected.
BUG=N/A
TEST=tested on fbg1701
Change-Id: Id11389ca90c1e6121293353402a2dd464a2e6727
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Fix regression introduced in recent SMM region handling overhaul.
Previously IED region size was hardcoded in the code. However when
chip code was modified to use smm_region() and friends, IED_SIZE
define was not added and build system quetly substituted it with 0.
Also, drop CONFIG_SMM_TSEG_SIZE which is now obsolete.
TEST=tested on watson platform; without the patch tg3 NIC driver doesn't work
properly and that gets solved with this patch
Change-Id: Id6fb258e555bb507851886b0e75f1f53c3762276
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36417
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Even though the vendor firmware enables the i8042 I/O port, it doesn't
feed valid data to those, but instead uses USB HID devices.
Disable the KBC port in SuperI/O and report no KCS port using FADT.
Fixes:
* Fixes error message in Linux that i8042 keyboard couldn't be enabled.
Tested on Supermicro X11SSH-TF:
The virtual remote managment console still works.
Change-Id: I1cdf648aa5bf1d0ec48520fa1e45bdaf043cb45d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Note that due to UNKNOWN_TSC_RATE, each stage will have
a slow run of calibrate_tsc_with_pit(). This is easy enough
to fix with followup implementation of tsc_freq_mhz() for
the cpu.
Change-Id: I0f5e16993e19342dfc4801663e0025bb4cee022a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36525
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CONFIG_FSP_CAR should not be a user visible option, but depends on the
choice presented in the soc Kconfig.
This also removes the dependencies on ADD_FSP_BINARIES. You need to
included those for other stages too so there is no need to make this
requirement explicit for FSP-T.
Change-Id: Ida32e9c4f5839aef4d4deb7a1c7fabe6335a5d2a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Internal/external displays functional on all variants
other than Samus. Unable to verify external outputs on
Samus (USB-C using DP/HDMI adapter).
Test: build/boot lulu variant with libgfxinit, verify internal/
external displays functional prior to OS display driver loaded.
Both linear framebuffer and scaled VGA text modes functional.
Change-Id: I867b2604861ebae02936e7fc0e7230a6adcb2d20
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The devicetree is not made for user-choosable options, thus introduce
Kconfig options for both SGX and the corresponding PRMRR size.
The PRMRR size Kconfig has been implemented as a maximum value. At
runtime the final PRMRR size gets selected by checking the supported
values in MSR_PRMRR_VALID_CONFIG and trying to select the value nearest
to the chosen one.
When "Maximum" is chosen, the highest possibly value from the MSR gets
used. When a too strict limit is set, coreboot will die, printing an
error message.
Tested successfully on X11SSM-F
Change-Id: I5f08e85898304bba6680075ca5d6bce26aef9a4d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Instead of doing our own calculations, rely on TOLUM returned by FSP
for cbmem_top. This (hopefully) saves us from making mistakes in weird
calculations of offsets and alignments.
Further this makes it easier to implement e.g. SGX PRMRR size selection
via Kconfig as we do not have to make any assumptions about alignments
but can simply pass (valid) values to FSP.
Tested successfully on X11SSM-F
Change-Id: If66a00d1320917bc68afb32c19db0e24c6732812
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36136
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for x86_64 bootblock on qemu.
Introduce a new approach to long mode support. The previous patch set
generated page tables at runtime and placed them in heap. The new
approach places the page tables in memory mapped ROM.
Introduce a new tool called pgtblgen that creates x86 long mode compatible
page tables and writes those to a file. The file is included into the CBFS
and placed at a predefined offset.
Add assembly code to load the page tables, based on a Kconfig symbol and
enter long in bootblock.
The code can be easily ported to real hardware bootblock.
Tested on qemu q35.
Change-Id: Iec92c6cea464c97c18a0811e2e91bc22133ace42
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
All of the EC_EVENT_* macros can be replaced with the EC_HOST_EVENT_*
macros defined in ec_commands.h, which is synchronized from Chromium OS
ec repository.
BRANCH=none
BUG=none
TEST=emerge-kukui coreboot
Change-Id: I12c7101866d8365b87a6483a160187cc9526010a
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Some mainboards with an ASPEED BMC do the serial routing setup in the
BMC boot phase on cold boot. This results in scrambled console output
when this is not finished fast enough.
This adds a delay of 500ms as workaround in the BMCs uart setup that
can be selected at mainboard level.
A user may disable the workaround when using another BMC firmware like
OpenBMC, u-bmc or some custom BMC bootloader with fast serial setup.
Change-Id: I7d6599b76384fc94a00a9cfc1794ebfe34863ff9
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36591
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On this platform the ramstage is run on a different core so passing
cbmem_top via calling arguments is not an option. To work around this
populate _cbmem_top_ptr with cbmem_top_chipset which is also used in
romstage.
Change-Id: I8799c12705e944162c05fb7225ae21d32a2a882b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36557
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
While commented as 10 ms + 250 us, those delay loops actually
accounted for a total of 840 ms. And they seem unnecessary
as followup code has potentially infinite retries when
polling for status changes.
Tested on aopen/dxplplusu, dual-socket P4 Xeon HT model_f2x.
Change-Id: Ib7d1d66ed29c62d97073872f0b7809d719ac2324
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested on thinkpad X200 with CONFIG_H8_FN_KEY_AS_VBOOT_RECOVERY_SW
selected, the RW_A slot is properly selected unless the FN button is
pressed. 600+ms are spend waiting for the EC to be ready.
Change-Id: I689fe310e5b828f2e68fcbe9afd582f35738ed1d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35998
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Multiple git checkouts cause GRUB2 to constantly rebuild even if there
were no changes to code or config. This is due to changing timestamps.
Fix this by not creating or switching branches but instead rely on
`git checkout -f` which does not touch existing unchanged files.
To be sure to not break anyones workflow checkout is skipped and a
warning gets printed if the tree/index is unclean.
Change-Id: I7cf66f63268de973a654146a0a47c3d5ca516d4d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36343
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Only use the custom hash routine when we need little endian.
Rename the function as well as it is little endian only now.
BUG=N/A
TEST=tested on fbg1701 board.
Change-Id: I037fa38c5961dab7a81e752c1685da2dc6b33d12
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36482
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Icelake default selects PLATFORM_USES_FSP2_1 which means stack will be shared
between FSP and coreboot (CONFIG_FSP_USES_CB_STACK) hence no need to have any
other default value than 129KiB (128KiB for FSP and 1KiB for coreboot)
Change-Id: I856f7e48a4a1e86eb082b9e772e0776664edca51
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36538
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch replaces BIOS OpRpm execution checks from CONFIG_INTEL_GMA_ADD_VBT
to CONFIG_RUN_FSP_GOP as adding VBT files doesn't mean GFX PEIM is going
to execute to initialize IGD.
Change-Id: Ic76529ba11f621f644d4472be6cbbc34682f00bf
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch makes below clean up for report_cpu_info() function
1. Replace cpu_string with cpu_not_found
2. Assign default string "Platform info not available" to cpu_not_found string
3. Add array out of bound check while skiping leading white space in cpu brand
string name
Change-Id: I41c76eb93f0c5229c4a49aa041339b8ad51ad34a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36531
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These are likely not properly set up and L1 is not even supported on
the desktop variant of the southbridge.
This fixes observed instability on some PCIe GPUs.
Change-Id: I70d3536984342614a6ef04a45bc6591e358e3abe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36576
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This solution is very generic and can in principle be implemented on
all arch/soc. Currently the old infrastructure to pass on information
from romstage to ramstage is left in place and will be removed in a
follow-up commit.
Nvidia Tegra will be handled in a separate patch because it has a
custom ramstage entry.
Instead trying to figure out which files can be removed from stages
and which cbmem_top implementations need with preprocessor, rename all
cbmem_top implementation to cbmem_top_romstage.
Mechanisms set in place to pass on information from rom- to ram-stage
will be replaced in a followup commit.
Change-Id: I86cdc5c2fac76797732a3a3398f50c4d1ff6647a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This solution is very generic and can in principle be implemented on
all arch/soc.
Instead trying to figure out which files can be removed from stages
and which cbmem_top implementations need with preprocessor, rename all
cbmem_top implementation to cbmem_top_romstage.
Mechanisms set in place to pass on information from rom- to ram-stage
will be placed in a followup commit.
Change-Id: If31f0f1de17ffc92c9397f32b26db25aff4b7cab
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Currently all stages that need cbmem need an implementation of a
cbmem_top function. On FSP and AGESA platforms this proves to be
painful and a pointer to the top of lower memory if often passed via
lower memory (e.g. EBDA) or via a PCI scratchpad register.
The problem with writing to lower memory is that also need to be
written on S3 as one cannot assume it to be still there. Writing
things on S3 is always a fragile thing to do.
A very generic solution is to pass cbmem_top via the program argument.
It should be possible to implement this solution on every
architecture.
Instead trying to figure out which files can be removed from stages
and which cbmem_top implementations need with preprocessor, rename all
cbmem_top implementation to cbmem_top_romstage.
TESTED on qemu-x86.
Change-Id: I6d5a366d6f1bc76f26d459628237e6b2c8ae03ea
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The x86 timers are a bit of a mess. Cases where different stages use
different counters and timestamps use different counters from udelays.
The original intention was to only flip TSC_CONSTANT_RATE Kconfig
to NOT_CONSTANT_TSC_RATE. The name would be incorrect though, those
counters do run with a constant rate but we just lack tsc_freq_mhz()
implementation for three platforms.
Note that for boards with UNKNOWN_TSC_RATE=y, each stage will have a
slow run of calibrate_tsc_with_pit(). This is easy enough to fix with
followup implementation of tsc_freq_mhz() for the platforms.
Implementations with LAPIC_MONOTONIC_TIMER typically will not have
tsc_freq_mhz() implemented and default to UNKNOWN_TSC_RATE. However,
as they don't use TSC for udelay() the slow calibrate_tsc_with_pit()
is avoided.
Because x86/tsc_delay.tsc was using two different guards and nb/via/vx900
claimed UDELAY_TSC, but pulled UDELAY_IO implementation, we also switch
that romstage to use UDELAY_TSC.
Change-Id: I1690cb80295d6b006b75ed69edea28899b674b68
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Some platforms lack a non-eviction mode and therefore caching the
whole ROM to speed up XIP stages can be dangerous as it could result
in eviction if too much of the ROM is being accessed. The solution is
to only cache a region, about the size of the stage that the bootblock
is about to load: verstage and/or romstage.
TODO: now a limit of 256KiB is set for the total amount of cache that
can be used. This should fit most use cases for the time being.
Change-Id: I94d5771a57ffd74d53db3e35fe169d77d7fbb8cd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
It is a user-visible option and enabled by default for ARCH_X86,
some consider it as debugging aid only. Therefore platform design
should not depend on it.
It must remain selected with CHROMEOS and boards are allowed
to explicitly select it as well.
For siemens/mc_bdx1,mc_aplX boot time will be increased due
the use of get_us_since_boot() with COLLECT_TIMESTAMPS=n.
When unable to determine if N seconds has elapsed from boot,
this turns into a delay of N seconds.
Change-Id: I6ee4195d266440143344781d39db9578cd8bdcb3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Use the new common function to set LT_LOCK_MEMORY at end of POST to
protect SMM in accordance to Intel BWG.
Tested successfully on X11SSH-M by disabling SGX and running chipsec.
Change-Id: I623e20a34667e4df313aeab49bb57907ec75f8a8
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The public key was not verified during the verified boot operation.
This is now added. The items in the manifest are now fixed at 12 as
we always have the postcar stage.
BUG=N/A
TEST=tested on facebook fbg1701
Change-Id: I85fd391294db0ea796001720c2509f797be5aedf
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36504
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
use coreboot MP init for saddlebrook by default.
BUG=None
TEST=Boot till yocto linux 2.7 on saddlebrook and verified the AP's
proper initialization using 'cat /proc/cpuinfo' command.
Change-Id: I2db2fe92c8ba0e649dccf95ce804a97ae4a05603
Signed-off-by: Praveen Hodagatta Pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Reviewed-by: Nico Huber <nico.h@gmx.de>
These changes are in accordance with the documentation:
[1] page 106, 7th Generation Intel(R) Processor Families for U/Y
Platforms and 8th Generation Intel(R) Processor Family for U Quad
Core and Y Dual Core Platforms. Datasheet, Volume 1. January 2019.
Document Number: 334661-006
Change-Id: I5232a7a670b97d51ff3b3b71a08f25f961ac1d6f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36058
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch creates a common instance of ipu.asl inside intel common
code (soc/intel/common/block/acpi/acpi) and ask cnl & icl soc code to
refer ipu.asl from common code block.
TEST=Able to build and boot Hatch and ICL DE system. Dump DSDT.asl to verify
Device(IMGU) presence after booting to OS.
Change-Id: I4d18571008c199fd5c3dbeed8cba9374520359b4
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch creates a common instance of globalnvs.asl/nvs.h inside intel common
code (soc/intel/common/block/) and ask cnl & icl soc code to refer globalnvs.asl
and nvs.h from common code block.
TEST=Able to build and boot Hatch and ICL DE system. Dump DSDT.asl to verify
GNVS operation region presence after booting to OS.
Change-Id: Ia9fb12a75557bd7dc38f6d22ba2b32065d18b3ee
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch creates a common instance of sleepstates.asl inside intel common
code (southbridge/intel/common/acpi) and asks all IA CPU/SOC code to
refer sleepstates.asl from common code block.
TEST=Able to build and boot Hatch and ICL DE system. Dump DSDT.asl to verify
S0/S3/S4/S5 entries after booting to OS.
Change-Id: Ie2132189f91211df74f8b5546da63ded4fdf687a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36463
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch creates a common instance of lpc.asl inside intel common
code (soc/intel/common/block/acpi/acpi) and asks specific soc code to
refer lpc.asl from common code block.
Note: From ICL onwards Intel Bus Device 0:1f.0 is known as eSPI
rather than LPC.
TEST=Able to build and boot ICL DE system. Dump DSDT.asl to verify
Device(LPCB) device presence after booting to OS.
Change-Id: I266d6e667e7ae794377e4882791e3be933d35e87
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36455
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Start using the vb2 public key format and process the signature
verification using the vb2 routines. This allows us to use the
futility to prepare the keys and eliminates the need for custom
tools.
BUG=N/A
TEST=tested on fbg1701 board
Change-Id: Id5d28595bbfb1f5ca5bca0fcfb06134bb1143f25
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
This adds a common cbmem_top implementation to all coreboot target.
In romstage a static variable will be used to cache the result of
cbmem_top_romstage.
In ramstage if CONFIG_RAMSTAGE_CBMEM_TOP_ARG is set a global variable
needs to be populated by the stage entry with the value passed via the
calling arguments. if CONFIG_RAMSTAGE_CBMEM_TOP_ARG is not set the
same implementation as will be used as in romstage.
Change-Id: Ie767542ee25483acc9a56785ce20a885e9a63098
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add a Kconfig option for indicating agreement to use the contents of
amd_blobs. Users should only download the repo after implicitely
agreeing to AMD's License text. No formal documented agreement
is required.
Update Makfile.inc, similar to other submodules, to initialize and
checkout the submodule once the Kconfig option is selected.
Change-Id: I4ae807659db16756453dc3db2c51848291c681b8
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This is currently an empty repo. The intention for amd_blobs may be
found in Documentation/soc/amd/amdblobs_license.md. A subsequent
patch will make the repo's init and checkout optional based on a
Kconfig symbol.
Change-Id: Ia93fb2711beaea4cb1c8e5d71dc3a9e0facc5485
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Quite a few new functions added here in order to support the use-case
of performing EC software sync within coreboot.
Most of these functions are related to retrieving the EC's hash, and
writing a new image into the EC's flash.
BUG=b:112198832
BRANCH=none
TEST=With whole patch series, successfully performed EC software sync
Change-Id: I0d3c5184dbe96f04b92878f2c19c7875503a910a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add a common function for setting LT_LOCK_MEMORY via MSR 0x2E7, which
locks most of the chipset BAR registers in accordance to Intel BWG.
Change-Id: I4ca719a9c81dca40181816d75f4dcadab257c0b3
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Currently full calibration with DVFS (which implies tripling memory
training time for multiple frequencies) will be run in recovery mode,
which takes up to 30 seconds with serial console enabled.
However, in recovery mode the system should be running only the recovery
programs with minimal services. DVFS should be not needed.
In order to improve stability and system boot time, we want to disable
DVFS training in recovery mode.
BRANCH=kukui
BUG=b:142358843
TEST=emerge-kukui coreboot
Change-Id: I4f1b1b020eba9bfce21655169bcb31b98d54b010
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36456
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Icelake platform doesn't support booting from any other media
(like eMMC on APL/GLK platform) than only booting from SPI device
and on IA platform SPI is memory mapped hence enabling temporarily
cacheing on memory-mapped spi boot media.
Also removed inclusion of unused header in cpu.c file
TEST=Able to build and boot ICL DE board.
Change-Id: I46d9ec054c4804ca756f2101085a55e91b5cc6f0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36431
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reduce duplicated comments explaining that submodules' settings in
.gitmodules are update=none, and that --checkout is required. This
prepares for another submodule, and makes adding a third set of
comments unnecessary.
Change-Id: I7721333a61122284ed9975ecd2adc3271a879728
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
AMD has generated a simpler and more flexible license agreement for
using proprietary precompiled binary images. The new agreement is
intended to cover all blobs in the directory structure below where
the license resides and eliminates any unique agreements previously
provided for individual products.
Add a description of the repo, as well as the license agreement it
contains.
Change-Id: Ia3dbc1a5259a2512281ea87b7e55fb3134b3b3c5
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
There are a lot of different implementations to pass information from
romstage to ramstage. These could all be unified by passing this
information via cbmem. Often however these methods exist for that very
purpose. This solves this by passing cbmem_top via the programs
arguments.
Change-Id: Id2031f7bb81ce65fc318313c270eb1fbae3b2114
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36272
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Each variant needed to define variant_early_gpio_table(), even if
it didn't need to make any changes. Added a __weak version of the
function into baseboard/gpio.c.
Certain upcoming Hatch variants will not use SPD files. Allow
SPD_SOURCES in spd/Makefile.inc to be empty.
BUG=None
BRANCH=None
TEST=Build coreboot and see that it builds without error
Change-Id: Ie946cfd7c071824168faa38fd53bd338a5a451e1
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36068
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Add defines for GPIO_MEM_CONFIG_0:3 in the template file, so
that code that relies on these defines can compile. Because they
are preprocessor symbols, there is no way to define them as
__weak in the baseboard header and allow the variant to override
as needed, so they need to be defined here and changed if needed.
* Add a version number for the script and an "auto-generated by"
line in the git commit message.
* Change the branch name so that it's not the same as the ones
that the other scripts will create, so that repo upload on those
CLs won't affect this one.
BUG=b:140261109
BRANCH=None
TEST=Create and build the "sushi" variant:
$ util/mainboard/google/hatch/create_coreboot_variant.sh sushi
$ util/abuild/abuild -p none -t google/hatch -x -a
Prior to this CL, you would get an error message that SPD_SOURCES is
not set. If you fixed that, then you would get failures for
GPIO_MEM_CONFIG_0, _1, _2, and _3 not defined, and/or gpio_table[]
and early_gpio_table[] not defined. After the CL, the build proceeds.
Change-Id: I0f48d6bb9544cad6d419d3a6fbb17f57200938b2
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36408
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code is based on autoport.
This port is tested on a T440p without a dGPU and can boot Arch Linux
from SATA disk with SeaBIOS payload. The tested components and issues
are in the documentation.
Change-Id: I56a6b94197789a83731d8b349b8ba6814bf57ca2
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34359
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As preparation for x86_64 clean the assembly code and introduce
arch/ram_segs.h similar to existing arch/rom_segs.h.
Replace open coded segment values with the defines from the new
header.
Change-Id: Ib006cd4df59951335506b8153e9347450ec3403e
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36321
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This includes a huge set of refactorings to support Core Display Clock
(CDClk) frequency switching based on the current mode requirements.
The CDClk is configurable since Haswell and runtime switching is suppor-
ted since Broadwell. Always using the lowest possible frequency setting
should allow some power-savings. While, on the upper end, we can support
higher resolution panels now, without having to change the static confi-
guration.
There have also been some smaller changes and fixes, including:
o Parsing of eDP 1.4+ DPCD link rates, enables panels that don't
advertise a maximum link rate but only individual ones.
o DP support for Ibex Peak.
o Corrected limit for HDMI on G45 to 165MHz.
o Reworked GMBUS reset handling and timeouts, should help with
stalled GMBUS controllers when unimplemented ports were probed
by accident.
Tested on various boards from GM45 to KBL-R.
Change-Id: I0a90bd4afe2091699a46a5a1323af9723ff43018
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35898
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If CPUID leaf 0x16 is available (Skylake and later) use it to obtain
current and maximum speed. Otherwise call weak function that can be
provided elsewhere (cpu/soc/mainboard). Also, populate "core enabled"
with the same value as "core count".
TEST=tested on OCP Monolake with dmidecode -t processor
Change-Id: Ie5d88dacae6623dfa0ceb3ca1bb5eeff2adda103
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
The i82801ix_early_init is now called both in the bootblock and
romstage. The rationale behind setting this up twice is to ensure
bootblock-romstage compatibility in the future if for instance VBOOT
is used.
This moves the console init to the bootblock.
The romstage now runs uncached. Adding a prog_run hooks to set up an
MTRR to cache the romstage will be done in a followup patch.
The default size of 64KiB is not modified for the bootblock as trying
to fit both EHCI and SPI flash debugging needs a more space and 64KiB
is the next power of 2 size that fits it.
TESTED on Thinkpad X200.
Change-Id: I8f59736cb54377973215f35e35d2cbcd1d82c374
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
With CONFIG_C_ENVIRONMENT_BOOTBLOCK it makes more sense to rely on the
size of the bootblock over CONFIG_XIP_ROM_SIZE. To make this work,
only powers of 2 are allowed as bootblock size.
Change-Id: Ic8104ca9c51e4d2eccdb277e4c2111d2da662f3e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
To make data flow more explicit, global variables 'MR01Value' and
'MR13Value' are replaced with local variables, which are passed as
function arguments.
BRANCH=kukui
BUG=none
TEST=1. emerge-kukui coreboot
2. Fast calibration succeeded
Change-Id: Id21483092c86c3ae7dbb1173a2b943defe41a379
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
If a device node should be enabled on some variants, but disabled on
others, it had better be declared as disabled (rather than absent) in
base device tree (rather than override tree for the variant disabling
it), and enabled in override tree for the variant needing it, so that
it does not need to be declared once more when adding another variant
with such node disabled.
Change-Id: I4b28360905ae38149ace9ac5d21cd6d5045b7584
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
There is no posibility to prevent loading images from cbfs at this stage
For security features prog_locate_hook() is added. This hook can be used
to prevent loading the image.
BUG=N/A
TEST=Created verified binary and verify logging on Facebook FBG-1701
Change-Id: I12207fc8f2e9ca45d048cf8c8d9c057f53e5c2c7
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Using docker to build to documentation eases the process of building
the documentation. Given that some versions of sphinx are
incompatible, the option to use docker is presented first.
Change-Id: I6c18f81a829364ada1859c04ba2dc4f886934bcc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36105
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change removes an inversion of GPP_D17 that caused the
device to get stuck in a reboot loop because the kernel was crashing
within the first couple seconds of kernel boot.
BUG=b:142515200
BRANCH=none
TEST=Flash and boot nocturne, verify boot is stable and that device
doesn't reboot after jumping into kernel, and that it passes the
'tast -verbose run <ip> hardware.SensorRing' test.
Change-Id: Ia1408ef6ea92f6b31a9f3eee8720954af3a7c382
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35967
Reviewed-by: Yicheng Li <yichengli@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are mainboards that do not have any graphics ports connected to
the SoC. It would be senseless to initialize the iGD, thus add a new
mainboard Kconfig to hide the GOP option.
Change-Id: Ica3b3a7a0c8120c95412369a24d8d669fb59fded
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
cbmem_top() should simply not be called before memory is initialed,
in order for the implementation to return something meaningful.
Change-Id: I8fe32844af290626a0f91279143fda4d3442680f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Michael Niewöhner
So, this is odd in multiple ways. First of all, we fix something:
We work around a weirdness in `make oldconfig` that adds spurious
entries into the `auto.conf` for choices that were given a symbol
name.
When introducing the Ada config package, it seemed reasonable to
use `auto.conf` as source, but it turned out that we didn't use it
as input, only `config.h` and the original `.config` were used. As
the syntax for `.config` is the same as for `auto.conf` we use the
former now as input for Ada, too. One question remains: If `.config`
already contains all required information, what is this `auto.conf`
and what does it want?
Alternatively, we could try to fix `oldconfig` or add a linter to
forbid named choices. I thought, our build test would reject the
latter already. But the `oldconfig` behaviour is too subtle.
We keep a dependency on the `oldconfig` step, to make sure it runs
first.
Change-Id: If3fe6bc782251cdbd696395d3069a1c0bb0ae802
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36320
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
New changes in the latest binutils 2.32 lead to assembler errors causes
ipxe build failure. IPXE uses the divide test which requires /dev/null as
input as well as the output file name.
This patch facilitates the /dev/null as an exception to the current
changes in binutils package while building crossgcc for coreboot leads to
successful build of ipxe and further tests to pass based on /dev/null and
applies automatically during the crossgcc rebuild.
Also, this can be reverted once binutils/ipxe provides an updated release
in this respect.
Fixes: https://ticket.coreboot.org/issues/204
Change-Id: I9f664829b8c42420c0b2ab1f2316150f86ac0b1a
Signed-off-by: Himanshu Sahdev <himanshusah@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35098
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the calculation of the Reserved Intel MMIO Memory size from
systemagent and memmap, since it is not needed.
The size is used in SA to calculate the space between cbmem_top and TSEG
without DPR and Chipset Reserved Memory. Since this will always be equal
to 0, the reservation will be skipped and TSEG, DPR and Chipset Reserved
Memory will get reserved alltogether.
By reading the code and pratical testing we figured out that:
- TSEG - DPR - reserved - top_of_memory == 0
- TSEG - DPR - reserved == top_of_memory
This means the whole block will never reserve anything because it is
always 0. Hence the code can be removed for simplification.
Tested successfully on X11SSM-F
Change-Id: I0cc730551eb3a79c78a971b40056de8d029f4b82
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This drops support for FSP 1.1 in soc/intel/skylake, after all boards
have been migrated to FSP 2.0, which is backwards compatible.
Any moving of files happens in a follow-up commit to make review easier.
Change-Id: I0dd2eab0edfda0545ff94c3908b8574d5ad830bd
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35813
Reviewed-by: Michael Niewöhner
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch is part of the patch series to drop support for FSP 1.1 in
soc/intel/skylake.
The following modifications have been done to migrate the board(s) from
FSP 1.1 to FSP 2.0:
- remove deprecated devicetree VR_RING domain (only 4 domains in FSP 2.0)
TODO:
- testing
Change-Id: I7481f3413de6780df01d9b769bd4f16d439f087c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35923
Reviewed-by: Michael Niewöhner
Reviewed-by: Wim Vervoorn
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- This port should be Reclaim Your Freedom compliant
(not certified yet).
- Untested on boards with external Radeon graphics adapter.
- Some columns on the left-most side of display are completely
black on 1400x1050 IPS display[1]. Display works fine on Linux.
I don't know why it appears like that. So far it has been observed
only with native graphics initialization.
- Only GRUB2 and SeaBIOS payloads tested for now.
- 2504 docking station USB doesn't work under Linux.
Can detect pendrive in GRUB2 payload.
- Sometimes it takes 20s of "pretending it's powered off" to run
coreboot code. Issue is payload agnostic.
Probably caused by missing one capacitor on my unit.
[1] https://imgur.com/a/0wpMGsm
Change-Id: Ibd9208a5eafd228f8eedbc8fb4f4eb9ed1932a14
Signed-off-by: Maciej Matuszczyk <maccraft123mc@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Remove SMM reinitialization since it's already done in src/ec/lenovo/h8.
Untested on a real hardware.
See also commit 8953d4a1 with Change-Id
I33fd829a7e34aefa8f76ca6020cc8e802f7aab17 ("mb/lenovo/*/smihandler: Get
rid of mainboard_io_trap_handler").
Change-Id: Icc582527db15f3a31cdee8948bc5a190240fdc84
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
mainboard_silicon_init_params() is supposed to be used for only
overriding any FSP params as per mainboard configuration. GPIOs should
be configured by mainboard as part of its chip init(). This ensures
proper ordering w.r.t. any common operations that the SoC code might
want to perform e.g. snapshot ITSS polarities.
This change moves the configuration of GPIOs from
mainboard_silicon_init_params() to mainboard chip->init().
Change-Id: I5d10c01c5b9d5f8ed02274d51dcf9c2a17269685
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36270
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
mainboard_silicon_init_params() is supposed to be used for only
overriding any FSP params as per mainboard configuration. GPIOs should
be configured by mainboard as part of its chip init(). This ensures
proper ordering w.r.t. any common operations that the SoC code might
want to perform e.g. snapshot ITSS polarities.
This change moves the configuration of GPIOs from
mainboard_silicon_init_params() to mainboard chip->init().
Change-Id: I5cd89c6e24b6a4b0c20fd476915f3781a0d46e0d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36269
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
mainboard_silicon_init_params() is supposed to be used for only
overriding any FSP params as per mainboard configuration. GPIOs should
be configured by mainboard as part of its chip init(). This ensures
proper ordering w.r.t. any common operations that the SoC code might
want to perform e.g. snapshot ITSS polarities.
This change moves the configuration of GPIOs from
mainboard_silicon_init_params() to mainboard chip->init().
Change-Id: Ied0201b954894acd3503801e7739b91a2cc9b4a8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36268
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
mainboard_silicon_init_params() is supposed to be used for only
overriding any FSP params as per mainboard configuration. GPIOs should
be configured by mainboard as part of its chip init(). This ensures
proper ordering w.r.t. any common operations that the SoC code might
want to perform e.g. snapshot ITSS polarities.
This change moves the configuration of GPIOs from
mainboard_silicon_init_params() to mainboard
chip->init(). Additionally, this change moves mainboard_ec_init() to
mainboard dev->init().
TEST=Verified that GPIOs are configured properly and hatch boots to
OS.
Change-Id: Ia509471a3678c60454cd4f14625f151860d9b9d2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36267
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set VPD keys for DSM parameters in overridetree.cb for Helios.
RT1011 driver will load values from VPD and set them to device property.
BUG=b:140397934
BRANCH=none
TEST=On Helios, with patch series, check realtek,r0_calib and
realtek,temperature_calib are available to rt1011 codec driver.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Change-Id: Ic72fd57becf93e70a1a716dbb76633509f2fd5c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The correct mapping for speakers to their names should be:
uid 0: Woofer Left
uid 1: Woofer Right
uid 2: Tweeter Left
uid 3: Tweeter Right
Also, fix the name to be 4-character.
BUG=b:140397934, b:143192767
BRANCH=none
TEST=On Helios, with patch series, check realtek,r0_calib and
realtek,temperature_calib are available to rt1011 codec driver.
And the speaker mapping is correct.
Change-Id: I353fb9ad0ca8ec85431eb2b59be748b4887278cf
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36256
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ACPI Version 6.3 Section 6.1: "A device object must contain either an _HID
object or an _ADR object, but should not contain both."
Found-by: ACPICA 20191018
Change-Id: I8bcdfa7a4dc33c3e3866d3135249a602379b9615
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36265
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ACPI Version 6.3 Section 6.1: "A device object must contain either an _HID
object or an _ADR object, but should not contain both."
Found-by: ACPICA 20191018
Change-Id: Iaa35790a38c36091a228007d739b970cb66a3e1c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36264
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ACPI Version 6.3 Section 6.1: "A device object must contain either an _HID
object or an _ADR object, but should not contain both."
Found-by: ACPICA 20191018
Change-Id: Ic0bcaa37ac017ab61e1fb4e78d3c7dfbbcc0899d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
ACPI Version 6.3 Section 6.1: "A device object must contain either an _HID
object or an _ADR object, but should not contain both."
Found-by: ACPICA 20191018
Change-Id: I9f55cc033b5672917520b139444bc614462c4a05
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add VPD variables for enabling/disabling FRB2 watchdog timer and
setting the timer countdown value. By default it would start the
timer and trigger hard reset when it's expired. The timer is
expected to be stopped later by payload or OS.
Right now the timer is started after FSP-M. Ideally it should be
before FSP-M (to detect memory training error).
Tested on OCP Mono Lake.
Change-Id: I82b244d08380a0461c92662e025d8b95b3133e23
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add a function for initializing and starting FRB2 timer with the
provided countdown and action values, and a stop function for
stopping the timer.
Tested on OCP Monolake.
Change-Id: Ic91905e5f01b962473b6b3a9616266d2d95b1d6b
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
As fmaptool can now handle the offset computation for every mentioned
region in the fmap file on its own there is no need to provide the
offset in the fmd file anymore. This patch clears this out so that the
files are way more readable now.
Change-Id: I1dc841604fdb662e08cb6690ff4bf6dd311e01d8
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
RT1011 is a smart amplifier. It needs to know speaker related parameters
including speaker resistor value and temperature when the calibration is
done in order to run Dynamic Speaker Management (DSM) algorithm on chip.
The purpose of DSM is to protect speaker when the volume is large.
The calibration data of speaker is stored in VPD in factory.
This driver is needed to read data from VPD and write to ACPI _DSD when
config CHROMEOS_DSM_CALIB is turned on.
Kernel rt1011 codec driver will read these device properties to set up
codec accordingly on boot.
The reason to prepare these parameters in coreboot is because kernel
codec driver expects to read per-device parameters directly from device
properties. Another benefit is that other OS can also take these
parameters through ACPI _DSD table and take benefit of DSM on RT1011.
The kernel driver device properties of RT1011 are documented at
linux/Documentation/devicetree/bindings/sound/rt1011.txt
It is currently in ASoC maintainer's tree at
https://kernel.googlesource.com/pub/scm/linux/kernel/git/broonie/sound/+/for-next/
and hopefully should be merged to mainline kernel in the next merge window.
BUG=b:140397934
BRANCH=none
TEST=On Helios, with patch series, check realtek,r0_calib and
realtek,temperature_calib are available to rt1011 codec driver.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Change-Id: I9550b9890ce2cae787f4f17779a5ade77f619171
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
On ChromeOS, there will be VPD values for dynamic speaker management (DSM)
calibration data. They are resistor calibration values and temperature
during calibration.
These VPD fields use "dsm_calib_" prefix.
Known keys are:
"dsm_calib_r0_0"
"dsm_calib_r0_1"
"dsm_calib_r0_2"
"dsm_calib_r0_3"
"dsm_calib_temp_0"
For now these values are unsigned decimal numbers greater than 0.
This library will be used for RT1011 device driver in the patch series.
Note that in the future we may encode more values into this VPD field if
needed. We retain the flexibility for coreboot device driver or codec
driver to decode/parse the VPD values based on the needed use case
per-board.
BUG=b:140397934
BRANCH=none
TEST=On Helios, with patch series, check realtek,r0_calib and
realtek,temperature_calib are available to rt1011 codec driver.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Change-Id: Ib9579a5cc055f8f438cb30a8acaf250a343db19e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Refactor I2C driver for fsp_baytrail to match the coreboot supported I2C
bus device structure. The internal I2C controllers are now handled by
the generic PCI driver approach and generic I2C access is enabled.
As orientation for the I2C code the actual solution from
soc/intel/apollolake I2C was taken. All the I2C specific parts were
removed from lpss.c and have been implemented in the I2C driver.
Future merge to soc/intel/common/block/i2c/i2c.c would be possible.
With this patch I2C chip devices can now be used in devicetree.
TEST=Booted siemens/tcu3 and verified that access to PTN3460 worked.
Change-Id: I3b87bd7c27e4c1afcce7cd4225cca02599f43c60
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
To allow retraining memory without hotkey (for example in manufacturing
process), we want to enforce re-training when the recovery reason is set
to VB2_RECOVERY_TRAIN_AND_REBOOT (which can be done by running
"crossystem recovery_request=0xc4").
The special reason was created for X86 MRC cache, for ensuring RO
calibration data is filled (the underlying implementation was in vboot,
not coreboot); and on MT8183 we have only RW calibration, but it seems
totally fine to extend that for RW.
BRANCH=kukui
BUG=None
TEST=boots; crossystem recovery_reason=0xc4; reboot
Change-Id: Iaa5275f0e0eb90f6ab3a7d4579977a6655d59bd9
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This adds another x11 series board, the X11SSM-F, which is similiar to
X11SSH-TF but differs in PCIe interfaces/devices, GPIO settings and
Ethernet interfaces.
Change-Id: I24e6f0f41a844652f88b562285b26beef311a2c9
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Michael Niewöhner
To fix MIPI D-PHY test failure, the hs-prepare should be less than
LimitMin from spec, and we have to enlarge TEOT margin.
BUG=b:138344447
BRANCH=kukui
TEST=Boots correctly on kukui
Change-Id: If91e7a546866299f02432be27fe778be5d7bdc5f
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
On hatch and variant HW designs supports VCCPRIM_CORE Low Voltage Mode.
VCCPRIM_CORE can be down to 0.75v when slp_s0 is asserted.
This commit enables PchPmSlpS0Vm075VSupport UPD so that FSP can
program related setttings to save power.
BUG=b:134092071
TEST=Run suspend_stress_test on kohaku and pass 100 cycles
Change-Id: Ia02ff8823883489b36349457213409496f082f36
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The previous code actually set SlpS0WithGbeSupport even when GBE is
disabled in device tree and could cause power consumption in s0ix.
This change will config PchPmSlpS0VmRuntimeControl, PchPmSlpS0Vm070VSupport,
PchPmSlpS0Vm075VSupport by device tree.
SlpS0WithGbeSupport will be set only when s0ix and gbe are enabled.
BUG=b:134092071
TEST=Run suspend_stress_test on kohaku and pass 100 cycles
Change-Id: I154a4e6970f99360aeb880d576eb61528034f7b6
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Commit 680027edf6 fixed a null dereference and logic bug in the tegra210
spi code:
soc/nvidia/tegra210: Fix potential NULL pointer dereference
Recent Coverity scan indicated potential NULL deference; if either
spi->dma_in or spi->dma_out are NULL, the fifo_error() check could
dereference a NULL pointer.
Also fixed what appears to be a logic bug for the spi->dma_out case,
where it was using the todo (count) from spi->dma_in.
Coverity is warning about the same problem for tegra124, so apply the
same fix there. Also, add braces around a while statement.
Change-Id: I6a7403417ee83b703cf4ca495129f73c66691ea9
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 124183, 124185
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Autoport generates these structures as static so let's make it consistent.
This commit follows up on commit 6752b615 with Change-Id
I4e07bd755ca4a65b76c69625d235a879fe7b43cb ("mb/*/*/gpio: Use static for
const structures").
Change-Id: Iaf9c796ca41218a9460ca6e0f64ef3e21a2ed2ff
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Build of the entire smm-class is skipped if we have
HAVE_SMI_HANDLER=n.
This commit follows up on commit 9265f89f with Change-Id
I10b4300ddd18b1673c404b45fd9642488ab3186c ("arch/x86: Avoid
HAVE_SMI_HANDLER conditional with smm-class").
Change-Id: If0e2a57283689a3cd1b97ee6e3c616fdefc0a028
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Adds the MSR table for server family 6 model 85 (5065x) processors (Sky
Lake, Cascade Lake, Cooper Lake).
The cores number for these processors exceeds the limit of 8 cores
(it is hardcoded in cpu.c). For this reason, the patch also adds code
that determines the number of processor cores at run time.
These changes are in accordance with the documentation:
[*] pages: 2-265 ... 2-286, 2-297 ... 2-308.
Intel(R) 64 and IA-32 Architectures, Software Developer’s Manual,
Volume 4: Model-Specific Registers. May 2019.
Order Number: 335592-070US
Change-Id: I27a4f5c38a7317bc3e0ead4349dccfef1338a7f2
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <anpetrov@fb.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I446cd267dec2b6c0f7742a6834c7ee950528ad5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Updated Authors file is in a separate commit.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ia0a07df6ca1fdaa2837ce8839057057cbd44d157
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Updated Authors file is in a separate commit.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I1acea8c975d14904b7e486dc57a1a67480a6ee6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Evaluated using 32-bit arithmetic, then used in a context that
expects an expression of type UINT64. Cast to UINT64 instead.
Change-Id: I4f0aa26e116b47505633897c790ca8e86ea5dc4e
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241847
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Rename the freeranges array to better match what they represent, i.e.
ranges that are used by the current running program and CAR region that
is not unallocated.
Skip adding the CAR region if cache-as-RAM is not active.
Change-Id: I78ee5536d890f30450a5ad2a753c948b02634d6d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36110
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch is part of the patch series to drop support for FSP 1.1 in
soc/intel/skylake.
The following modifications have been done to migrate the board(s) from
FSP 1.1 to FSP 2.0:
- remove deprecated devicetree VR_RING domain (only 4 domains in FSP 2.0)
- drop FSP-1.1-only romstage.c and spd.c
TODO:
- testing
Change-Id: I9d312ac959a7dac4b018d5ca1d007b1347bcf1dd
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch is part of the patch series to drop support for FSP 1.1 in
soc/intel/skylake.
The following modifications have been done to migrate the board(s) from
FSP 1.1 to FSP 2.0:
- remove deprecated devicetree VR_RING domain (only 4 domains in FSP 2.0)
- switch to using the FSP default VBT
TODO:
- testing
Change-Id: Id747ef484dfdcb2d346f817976f52073912468d0
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Icc/Loadline automatic detection is supported only for FSP2.0
These changes are in accordance with the documentation:
[*] S-Platforms, Document Number: 332687-008EN
[*] H-Platforms, Document Number: 332986-010EN
[*] U/Y-Platforms, Document Number: 332990-008EN
Change-Id: I8e517d8230c251e0cd4b1d4f1b9292c3df80cb19
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Similar to MRC cache on x86 platforms, when a hotkey is pressed during
boot, the calibration data cache saved in the flash will be cleared,
consequently triggering DRAM retraining (full calibration) in the next
boot.
BRANCH=kukui
BUG=b:139099592
TEST=emerge-kukui coreboot
Change-Id: I2f9225f359e1fe5733e8e1c48b396aaeeb9a58ab
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
SoC DRAM team suggested always running full calibration mode in recovery
mode because it is possible to get unstable memory even if the complex
memory test has been passed.
Since the recovery mode runs from RO and we only have training data
cache for RW, the trained calibration data can't be saved since RO and
RW may be running different firmware.
Also revised few message to make it more clear for what calibration mode
(fast, full, or partial) has been executed.
BRANCH=kukui
BUG=b:139099592
TEST=emerge-kukui coreboot
Change-Id: I29e0df71dc3357462e15ce8fc2ba02f21b54ed33
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This reverts commit d5018a8f78.
Reason for revert: Breaks boot on Whiskey Lake-U boards
Both System76 and Purism have had memory initialization failures
when this patch is applied, with the following error message:
Failed to accommodate FSP reserved memory request!
An extra 4096 bytes needs to be reserved for the FSP on these
systems, and reinstating the PTT reservation does this as
expected. PTT is enabled for the System76 galp3-c in the
ME configuration, which is why the behaviour is different.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
CC: Matt DeVillier <matt.devillier@gmail.com>
CC: Subrata Banik <subrata.banik@intel.com>
Change-Id: Ib82f02c4a2b1cd2dbf95d4ca4a9edd314e78edd2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35924
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
An important piece of information contained in the APCB is a copy of
SPD-type data to use for soldered down memory. The amdfwtool has
been updated with the ability to build five APCBs into the PSP's BIOS
Directory Table. Modify Picasso's Kconfig and Makefile.inc to take
advantage of the flexibility, and pass the correct instance ID to
amdfwtool.
Change-Id: I0efa02cb35f187ca85a8f0d8bd574fc438e6dc0a
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Increase the number of potential APCB images to 5 by adding to the
amd_bios_table. New instance IDs are from 0 to 4. The backup APCB
block (type 0x68) still supports only instance ID 0.
Change-Id: Ib70dc6417fecf94549a0c7df36ea42f63331be26
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The current DCACHE_BSP_STACK_SIZE is set to 128KiB for CML & ICL when
FSP uses the same stack provided by coreboot. This patch updates it to
129KiB since the default value of DCACHE_BSP_STACK_SIZE must be
the sum of FSP-M stack requirement (128KiB) and CB romstage
stack requirement (~1KiB).
BUG=b:140268415
TEST=Build and boot CML-Hatch.
Change-Id: Icedff8b42e86dc095fb68deb0b8f80b2667cfeda
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36032
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a function to uart.c to ensure the right IOMux settings are
programmed for the console UART. Update Kconfig to reflect the
new addresses.
Give the user the ability to downclock the UARTs' refclock to
1.8342MHz.
Add the abiltiy to use an APU UART at a legacy I/O address.
Update the AOAC register configuration for the two additional
UARTs.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I74579674544f0edd2c0e6c4963270b442668e62f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Picasso's FCH has many similarities to Stoney Ridge, so few changes
are necessary. The most notable changes are:
* Update the index values for the C00/C01 interrupt routing
* FORCE_STPCLK_RETRY is not present
* PCIB is not defined
* FCH MISC Registers 0xfed80e00 numbering has changed
* C-state base moves from PM register to MSR
* Add option to determine the intended MUX settion for LPC vs. eMMC
* Remove the LEGACY_FREE option
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I69dfc4a875006639aa330385680d150331840e40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The LPC-ISA bridge supports two ranges for SuperIO control registers.
Add a generic function to allow a mainboard to enable the appropriate
range. Provide #define values that are more descriptive than the
register's field names.
Change-Id: Ic5445cfc137604cb1bb3ee3ea4c3a4ebdb9a9cab
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35271
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change to the appropriate device IDs. Remove the ehci resource
call. Remove overcurrent settings, as this will be passed to
AGESA in later change.
Remove unused USB2 ACPI name assignment.
Change-Id: Ic287a05b30ca03e3371cc4a30aaa93b236c6d3fb
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add Kconfig options and Makefile command line options to generate
the amdfw.rom image. A new intermediate image is introduced, which
is the initial BIOS image the PSP places into DRAM prior to
releasing the x86 reset. The amd_biospsp.img is a compressed
version of the romstage.elf program pieces.
Additional details of the PSP items are not public information. See
NDA document PID #55758.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Ib5e393e74ed60e968959012b6275686167a2d78a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
It is similar to X200s, with U-series CPU, slightly different gpio
setup, no docking support, and no superio chip.
Tested:
- CPU Core 2 Duo U9400
- Slotted DIMM 4GiB*2 from samsung
- Camera
- pci-e slots
- sata and usb2
- libgfxinit-based graphic init
- NVRAM options for North and South bridges
- Sound
- Thinkpad EC
- S3
- Linux 4.19.67-2 within Debian GNU/Linux stable, loaded from
Linux payload (Heads) and Seabios.
TODO: repurpose and/or rename flag H8_DOCK_EARLY_INIT (introduced in
CB:4294 ) for h8-using devices without a dock.
Change-Id: Ic6a6059ccf15dd2e43ed4fc490c1d3c36aa1e817
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
FBG-1701 revision 1.3 will use Kingston onboard memory.
Add Kingston SPD file.
When Samsung memory configuration is disabled use
cpld_read_pcb_version() for using correct SPD data.
BUG=N/A
TEST=Boot and verified on Facebook FBG-1701 revision 1.3
Change-Id: I2e1d1b933d5a49a7005685ed530c882429019027
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35792
Reviewed-by: Wim Vervoorn
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change d3a1a417 "src/superio: Remove unused superio chips" removed
all unused devices except for ones used on mainboards still under
review. The SMSC 1036 was inadvertenly also removed as well. This
device is used in debug cards that may be connected to AMD CRBs.
This patch restores the smsc1036 directory as-is and then corrects
the following lint messages.
* WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
* ERROR: else should follow close brace '}'
* WARNING: braces {} are not necessary for single statement blocks
Change-Id: I851826e12032f802b9b2ff86d5a0eb99871bee6d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36119
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The DRAM calibration blob can be compressed using pre-RAM algorithm
(currently LZ4), which will save ~12ms in boot time.
On Kodama, boot time difference:
Before: 1,082,711
After: 1,070,309
BUG=b:139099592,b:117953502
TEST=build and boot, cbfstool coreboot.rom print -v (see dram compressed)
BRANCH=kukui
Change-Id: Ic3bd49d67ee6f80a0e4d8f6945744642611edf64
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Chrome OS firmware images have moved bitmap resources from GBB into CBFS
for a long time, so the GBB should only hold firmware keys and HWID,
that is usually less than 10k.
ARM boards usually limit GBB to 0x2f00 (see gru, cheza and kukui) but
many recent x86 simply copy from old settings and may run out of space
when we want to add more resources, for example EC RO software sync.
Note, changing the GBB section (inside RO) implies RO update,
so this change *must not* be cherry-picked back to old firmware
branches if some devices were already shipped.
BRANCH=none
BUG=None
TEST=make # board=darllion,hatch,kahlee,octopus,sarien
Change-Id: I615cd7b53b556019f2d54d0df7ac2723d36ee6cf
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The two GPIO functions variant_gpio_table() and
variant_early_gpio_table() provide the pointer to the variants GPIO
table for late and early GPIO init. As these functions are variant
dependent the keyword __weak must not be used as otherwise the linker
might choose the tables from the baseboard.
This patch removes the __weak definition making these functions
overriding the general ones in baseboard/gpio.c.
Change-Id: Ic7fc816d40cb112d7ab51089c3962a77798c08a8
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36094
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To make data flow more explicit, global variable 'impedance' is replaced
with a local variable, which is passed as a function argument.
BUG=none
BRANCH=kukui
TEST=Krane boots correctly
Change-Id: I0f6dacc33fda013a3476a10d9899821b7297e770
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The patch adds config MT8183_DRAM_DVFS to enable DRAM calibration with
multiple frequencies to support DVFS switch.
BUG=b:80501386,b:142358843
BRANCH=kukui
TEST=Boots correctly on Kukui
Change-Id: I97c8e513dc3815a2d62b2904a246a1d8567704a4
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This patch supports voltage adjustment for each DRAM frequency, which is
neccesary to support DVFS switch.
BUG=b:80501386,b:142358843
BRANCH=none
TEST=Boots correctly and stress test pass on Kukui.
Change-Id: I9539473ff708f9d0d39eb17bd3fdcb916265d33e
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
DRAM DVFS needs to be calibrated with different vddq voltages to get
correct parameters.
A new API is added to allow changing vddq voltage.
BUG=b:80501386
BRANCH=none
TEST=measure vddq voltage with multimeter
Change-Id: I5f0d82596a1709bf0d37885f257646133f18f210
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35147
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
DRAM DVFS needs to be calibrated with different vdram1 voltages to get
correct parameters.
A new API is added to allow changing vdram1 voltage.
BUG=b:80501386
BRANCH=none
TEST=measure vdram1 voltage with multimeter
Change-Id: Ia15ab3a2e1668e5b4873d317b57a38ebee037709
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33186
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Most coreboot debug messages are sent to UART and cbmem console, and we
also want to collect DRAM calibration module output, especially for
cbmem console (so we can see the logs after kernel is up).
Instead of sharing whole cbmem/cbtable/cbmemconsole implementations, we
want to simplify that by a simple function pointer so output can be
preserved by do_putchar, which internally sends data to all registered
consoles (usually cbmem console and UART).
BUG=b:139099592
TEST=make; boots properly for full-k, with and without serial console.
BRANCH=kukui
Change-Id: I1cf16711caf3831e99e17b522b86694524425116
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36056
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previously if .xcompile was missing, abuild would silently ignore the
error. With https://review.coreboot.org/c/coreboot/+/34241 we now check
the return code so abuild started failing.
We should generate the .xcompile if it doesn't exist. The Makefile will
handle that so we include it as the first Makefile.
We then need to override the default target so we don't use the one from
the Makefile.
BUG=b:112267918
TEST=ran abuild and made sure it generated a .xcompile in the root.
Change-Id: I79ded36d47b0219d0b126adff80a57be1c2bdf07
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
During the raminit the CPU gets reset but the platform does not. To
deal with TPM init failure (a TPM can only be started up once) ignore
the invalid POSTINIT return code.
Change-Id: Ib15e796914d3e6d5f01b35fa46b3ead40f56122b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36055
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are use cases where TPM has already been set up in a previous
stage, e.g. TXT or when a CPU reset without a platform reset happens.
If this is the case the TPM startup will return a
INVALID_POSTINIT (return code 0x26). This adds a Kconfig to allow
platforms to disregard that return code.
Change-Id: I238b30866f78608c414de877b05a73cf8fdb9bbd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The checksum is stored in the header of calibration data and saved to
SPI flash. After reading the data from flash, checksum is used to verify
the integrity of the calibration parameters.
BUG=b:139099592
BRANCH=kukui
TEST=Calibration data successfully loaded from flash
Change-Id: Ie4a0688ed6e560d4c0c6b316f44e52fd10d71a9d
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
If DRAM calibration fails or mem test fails using the cached calibration
results stored in flash, rerun DRAM full calibration. If partial
calibration fails or the mem test following it fails, hang forever.
Partial calibration acts as a fallback approach in case of full
calibration failure. Therefore, if it fails, there would be no other
ways to initialize DRAM. Instead of falling into reboot loop and
draining out of battery, it is better to just hang so that the end user
may notice that and send to RMA.
BUG=b:80501386,b:139099592
BRANCH=kukui
TEST=Boots correctly on Kukui
Change-Id: I8e1d4f5bc7b45f45a8bfef74e86ec0ff6a556af4
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35481
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
During the raminit the CPU gets reset, so reprogram those bits in
PM1_CNT such that the CPU remains aware that this is a S3 resume path
after the reset.
Change-Id: I8f5cafa235c8ab0d0a59fbeeee3465ebca4cc5d0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
I tested the SPI through the SD card and fixed sd card communication problem.
Added two functions (claim_bus and release_bus). Setting CS signal is invalid by
default.
Change-Id: I60033a148c21bbd5b4946580f6cab0b439d346c6
Signed-off-by: Xiang Wang <merle@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
It turned on some SKUs FSP hangs in Notify stage if IIO root ports are
disabled after MemoryInit. To address that hide IIO root ports earlier
in romstage.
TEST=the patch was ran on affected HW and success was reported
Change-Id: I6a2a405f729df14f46bcf34a24e66e8ba9415f9d
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This sets up some common default LPC decode ranges in a common place.
This may set up more decode ranges than needed but that typically does
not hurt. Mainboards needing additional ranges can do so in the
mainboard pch_enable_lpc hook.
Change-Id: Ifeb5a862e56f415aa847d0118a33a31537ab8037
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
As VGA_ROM_RUN and libgfxinit are mutually exclusive in Kconfig,
we don't have to guard all the VGA BIOS if's and can assume
gfx_get_init_done() returns 0 until all the quirks are handled.
Then, we can run libgfxinit.
Change-Id: Id5d0c2c12b1ff8f95ba4e0223a3e9aff27547acd
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/20100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Port the backlight-PWM handling from Skylake instead of the previously
used Haswell version. We use a 200Hz PWM signal for all boards. Which
is higher than the previous devicetree value, 183Hz, but that was over-
ridden by the VBIOS anyway. 200Hz is still very low, considering LED
backlights, but accurate values are unknown at this time.
Lynx Point, the PCH for Haswell and Broadwell, is a transition point
for the backlight-PWM config. On platforms with a PCH, we have:
o Before Lynx Point:
The CPU has no PWM pin and sends the PWM duty-cycle setting
to the PCH. The PCH can choose to ignore that and use its own
setting (BLM_PCH_OVERRIDE_ENABLE).
We use the CPU setting on these platforms.
o Lynx Point + Haswell:
The CPU has an additional PWM pin but can be set up to send
its setting to the PCH as before. The PCH can still choose
to ignore that.
We use the CPU setting with Haswell.
o Lynx Point + Broadwell:
The CPU can't send its setting to the PCH anymore. BLM_PCH_
OVERRIDE_ENABLE must always be set(!) if the PCH PWM pin is
used (it virtually always is).
We have to use the PCH setting in this case.
o After Lynx Point:
Same as with Broadwell, only BLM_PCH_OVERRIDE_ENABLE is
implied and the bit not implemented anymore.
Change-Id: I1d61d9b3f1802ebe18799fc4d06f1f1d3b54c924
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
When `mode_validate` was added, a second copy of `mode_layout` was
accidentally added to the multiple-mode-argument check instead. This
prevents `-f` from working. Fix the check to reference the correct
variable.
Change-Id: Ibac6f090550ff63ec9158355b0450da204a300a7
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Required for new VB2_ASSERT and VB2_DIE macros in vboot code.
(See chromium:972956.)
BUG=b:124141368, chromium:1005700
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I61a1036ccab80862d6eb12f9f72286f29e8478cf
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Enable wifi sar feature and set wifi sar name for dragonair sku.
BUG=b:142109545
TEST=emerge-hatch coreboot chromeos-bootimage
1. Check wifi_sar-dragonair.hex in /cbfs-rw-raw/dratini
2. Add iwlwifi.debug into kernel params.
3. check SAR value from dmesg only when sku id is 21/22
Change-Id: I0e08610b7c7d2d8da5a749d278bcde26af590e31
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
APL unhides the P2SB device in coreboot already. Do the same on SKL/KBL.
As the coreboot PCI allocator needs to be able to find the device,
unhide it after FSP-S.
The device is hidden in the SoC finalize function already and not visible
in the OS, as more P2SB device IDs have been added.
Other SoCs aren't updated, because they are too broken.
Fixes "BUG: XXX requests hidden ...." warnings in coreboot log.
Tested on Supermicro X11SSH-TF.
Change-Id: I0d14646098c34d3bf5cd49c35dcfcdce2c57431d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner
On Hyper-Threading enabled platforms the MSR_PRMRR_PHYS_MASK was written
when already locked by the sibling thread. In addition it loads microcode
updates on all threads.
To prevent such race conditions only call the code on one thread, such
that the MSRs are only written once per core and the microcode is only
loaded once for each core.
Also add comments that describe the scope of the MSR that is being
written to and mention the Intel documents used for reference.
Fixes crash in SGX MP init.
Tested on Supermicro X11SSH-TF.
Change-Id: I7102da028a449c60ca700b3f9ccda9017aa6d6b5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35312
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The port is based on the x201 / t410s.
2537-vg5 / i5, no discrete gpu
Tested and working:
* Native raminit
* Native gfxinit
* Booting Seabios 1.12.1
* Booting from EHCI
* Running GNU/Linux 5.0.0
* No errors in dmesg
* EHCI debug on the devices left side, bottom-right
* Keyboard
* Fn keys (Mute, Volume, Mic)
* Touchpad
* TPM
* Wifi
* Sound
* USB
* Ethernet
* S3 resume
* VBOOT
Testing in progress.
Untested:
* VGA
* Displayport
* Docking station
Bugs:
* AC adapter can't be read from ACPI
* TPM not working with VBOOT and C_ENV BB
Details for flashing externally:
1. Disconnect all power
2. Connect the external flasher
3. Connect the power cord (This fixes internal power control)
4. Remove the power cord
Change-Id: Id9d872e643dd242e925bfb46d18076e6ad100995
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/11791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This assumes ACPI aware OS also have a driver for this particular
hardware, which is the case for at least Linux. This saves ~60ms on S3
resume.
Change-Id: I2dcd399fee8e2d1cd1b70e60e1669a49c7aa8cb4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This does the following:
- Add gen[1-4]_dec options to the devicetree to set up generic LPC
decode ranges in the southbridge code.
- Move setting up some default decode ranges to a common place. If
somehow a board needs to override this behavior it can happen in the
mb_setup_superio() hook (that will be renamed when moving to
C_ENVIRONMENT_BOOTBLOCK).
Change-Id: I3d904b1125bc410c11aa73a89b1969284e88dac1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
These SIOs are not being used or tested by abuild, so remove them from the
tree. The only 3 currently unused SIOs that don't get removed here have board
ports in review.
src/superio/fintek/f71805f
src/superio/fintek/f71872
src/superio/intel/i8900
src/superio/ite/it8671f
src/superio/ite/it8716f
src/superio/nsc/pc87309
src/superio/nsc/pc87360
src/superio/nsc/pc87366
src/superio/nsc/pc97317
src/superio/smsc/dme1737
src/superio/smsc/lpc47b272
src/superio/smsc/lpc47b397
src/superio/smsc/sch4037
src/superio/smsc/sio1036
src/superio/via/vt1211
src/superio/winbond/w83697hf
src/superio/winbond/wpcd376i
Signed-off-by: Martin Roth <martin@coreboot.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I61d486d2c1e2b85eb292eaa78316c36e1735ebf4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
A few notable changes:
- Microcode init is done in assembly during the CAR init.
- The DCACHE_BSP_STACK_SIZE is set to 0x2000, which is the same size
against which the romstage stack guards protected.
- The romstage mainboard_lpc_init() hook is removed in favor of the
existing bootblock_mainboard_early_init().
Change-Id: Iccd7ceaa35db49e170bfb901bbff1c1a11223c63
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This allows to read and set bits in the EC ram in the bootblock or
verstage. This can be useful if one needs to read a keyboard key as an
input for get_recovery_mode_switch in vboot.
Change-Id: I20b2264012b2a364a4157d85bfe5a2303cc5e677
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
According to the documentation [1], IA32_PLATFORM_ID MSR register
address should be 17H.
[1] Table 2-2. Intel (R) 64 and IA-32 Architectures Software Developer’s
Manual. Volume 4: Model-Specific Registers. May 2019.
Order Number: 335592-070US
Change-Id: I9a16b162db51d21c7849b3c08c987ab341845b1e
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The NO_POST option covers more than classical port 80 output, hence
selecting it seems wrong in any case. The default is still rather
user patronizing, but let's keep it.
As a side effect, this fixes the ability to override the default
for NO_POST which Kconfig rejected while these boards selected it.
(Seems like a bug in Kconfig, though.)
Change-Id: I896b08812b1aa6ce249d7acc8073ebcc0f72eace
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
The next board rev will have a new option for an Elan touchscreen. Add
support for this in the devicetree, as well as use the 'probed' property
on both touchscreen options.
BUG=b:141957731
BRANCH=none
TEST=compiles (next board rev not available yet)
Change-Id: I135e693304cbb8dffc0caf4c07846033d6802208
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Load the calibration params from flash first and check the correctness
of the params. If the params have correct format, perform DRAM fast
calibration with these params to reduce bootup time. Otherwise, load the
DRAM blob and perform DRAM full calibration.
Bootup time of DRAM partial calibration:
- 1,349,385 usecs with low frequency
- 924,698 usecs with middle frequency
- 1,270,089 usecs with high frequency
3,544,172 usecs in total.
Bootup time of DRAM fast calibration:
- 216,663 usecs with low frequency
- 328,220 usecs with middle frequency
- 322,612 usecs with high frequency
867,495 usecs in total.
BUG=b:139099592
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: I8de29b14b1fb24b3b4f351c855c5c4d8f350cc34
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Load calibration params from flash. If the format of the params is
correct, use these calibration params for fast calibration to reduce the
bootup time.
Bootup time of DRAM partial calibration:
- 1,349,385 usecs with low frequency
- 924,698 usecs with middle frequency
- 1,270,089 usecs with high frequency
3,544,172 usecs in total.
Bootup time of DRAM fast calibration:
- 216,663 usecs with low frequency
- 328,220 usecs with middle frequency
- 322,612 usecs with high frequency
867,495 usecs in total.
BUG=b:139099592
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I9ef4265dd369a1c276bb02294696556df927e7bc
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35164
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The dramc_param module simplifies the communication between coreboot and
MTK DRAM full calibration blob, and is shared by both implementations to
ensure the same format of parameters.
BUG=b:139099592
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: I4cfd634da1855a76706aab0b050197251e2ed4dd
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Since we always write to &ch[chn].ao.dummy_rd after calling
dramc_engine2_end(), this write could be merged into dramc_engine2_end()
to simplify code.
BUG=none
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: Ibb4bd5ed016118811ad2097098417c19f00f4263
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35749
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Nuvoton and Winbond use the same off-by-5 indirect address space to
access their hardware monitor/environment controller in the SIO chip, so
move this to a common location and replace the inb/outb calls with the
corresponding inline functions from device/pnp.h
Change-Id: I20606313d0cc9cf74be7dca30bc4550059125fe1
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Setting the cbfs prefix is prone to error. Therefore add a Kconfig
choice for 2 common values, fallback and normal, while still keeping
the ability to specify an arbitrary value.
Change-Id: I04222120bd1241c3b0996afa27dcc35ac42fbbc8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The value stored to 'spd_bytes_total' is never read. Now it is fixed.
This is spotted using clang-tool v9.
Also add a check if spd_bytes_used and/or spd_bytes_total are reserved
and make sure that spd_bytes_used is not greater than spd_bytes_total.
Change-Id: I426a7e64cc4c0bcced91d03387e02c8d965a21dc
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This reverts commit 275f2e22a1.
Since in this commit the inclusion of site-local/Makefile.inc was moved
outside of the guard 'ifeq ($(NOCOMPILE),1)', this Makefile.inc will be
included always here (what seems to be the intention of this commit).
As we have a second place where site-local/Makefile.inc is included
(top-level Makefile.inc via subdirs-y class) this unconditional include
leads to a double included site-local/Makefile.inc. Therefore one will
get errors if a separate rule is used in site-local/Makefile.inc.
Change-Id: I0a693c1d793b978c8023e4f107dce139d537d8db
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Applying reset_gpio config of stylus for kohaku. GPP_A19 has been assigned in
the latest schematics.
We would keep GPP_A10 as output high for old revision devices temporarily.
BUG=b:141914474
BRANCH=none
TEST=verified stylus works internally
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: I61f0f9a4378f47bf455f0726d44beeaf2f67197b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Add PRESERVE to UNIFIED_MRC_CACHE so that we don't retain the memory
training data upon a FW update unless we need to. We have had users
complaining that a 15 second memory training upon update makes them
believe that their device is not booting, thus many of them hard
resetting before bootup.
BUG=b:142084637
BRANCH=None
TEST=flash RW_SECTION_A, RW_SECTION_B, and WP_RO sections and make
sure memory training doesn't occur on following bootup.
Change-Id: Ia5eb228b1f665a8371982544723dab3dfc40d401
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35803
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
RCBA_HPTC needs to be read back to consistently enable HPET.
This ought to fix raminit failing sometimes and SeaBIOS endlessly
waiting for user input.
TESTED on Intel D510MO, Fixes SeaBIOS waiting for input, without a
timeout.
Change-Id: I20a25fd97cd09fedb70469262c64d8d3828bb684
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35758
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
So, the PCI to PCI bridge specification had a pitfall for us:
Originally, when decoding i/o ports for legacy VGA cycles, bridges
should only consider the 10 least significant bits of the port address.
This means all VGA registers were aliased every 1024 ports!
e.g. 0x3b0 was also decoded as 0x7b0, 0xbb0 etc.
However, it seems, we never reserved the aliased ports, resulting in
silent conflicts we preallocated resources. We neither use much
external VGA nor many i/o ports these days, so nobody noticed.
To avoid this mess, a bridge control bit (VGA16) was introduced in
2003 to enable decoding of 16-bit port addresses. As older systems
seem rather safe and well tested, and newer systems should support
this bit, we'll use it if possible and only warn if not.
With old (AGP era) hardware one will likely encounter a warning like
this:
found VGA at PCI: 06:00.0
A bridge on the path doesn't support 16-bit VGA decoding!
This is not generally fatal, but makes unnoticed resource conflicts
more likely.
Change-Id: Id7a07f069dd54331df79f605c6bcda37882a602d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35516
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The assumption is made that an ACPI aware an OS does not rely on
firmware to initialize the display.
TESTED on a Lenovo Thinkpad X201 with Linux 5.2, display still works
after S3, more than 200ms in time saved (dropped from 411ms to 182ms
in total in one test).
Change-Id: I36219e6d04db561d4f2ddb6e962166c598d5bc4f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This change does the following:
- Move PCH init code from the common romstage to sb code, this allows
for easier reuse in bootblock
- Provide a common minimal LPC io decode setup, mainboards can
override this in the mainboard_lpc_init if required
- Set up LPC generic IO decode up in romstage based on devicetree
settings
- Remove the ramstage LPC generic IO decode from ramstage as this is
now done in romstage.c
- Get rid of unneeded setup of spi_read configuration in BIOS_CNTL as
this is already done in the bootblock.
Change-Id: I3f448ad1fdc445c4c1fedbc8497e1025af111412
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This is based on the sandybridge settings.
The current lookup table comes from the x201 vendor lookup table.
Tested: USB mouse and webcam still work and current registers are the
same as before. USB IR are not but the code follows EDS instead of the
register replay.
Change-Id: Icea9673623a62e7039d5700100a2ee238478abd1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35762
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The RCBA registers 0x3400-0x3500 are all handled elsewhere
in the code, so no need to have a 'replay' of those.
The remainder now consist of USB setup and undocumented bits
that should likely not be touched at all.
Change-Id: I69fc8a5e16f7cf0e1068d0d2ed678a6c2f6e70a9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This does the following:
- implement a PCH disable function that will be called by the PCI
drivers as part of their chip_ops
- removes the iobp_x calls as those don't exist on ibexpeak
- complete the devicetree with to be disabled PCI devices for the
chip_ops to be called
- Clean up some code copied from bd82x6x
Change-Id: I78d25ffe9af482c77d397a9fdb4f0127e40baddc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This properly sets up the chipset initialization registers, instead of
replaying an RCBA dump.
The information is taken from the EDS and from the thinkpad x201
vendor BIOS disassembly and from an HP UEFI.
TESTED on Thinkpad X201. Seems stable at booting, rebooting and resume
from S3.
Change-Id: I21c2beaf70da27dbe6a56e2612df2c257c05fc62
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Intel adopted xx_DEVFN_xx naming for macros expanding to
PCI_DEVFN() starting with apollolake. The ones named
xx_DEV_FUNC are being renamed, or dropped, if they
were generally not used at all for a platform.
Change-Id: Id78e594ae6490d39df76317f8fc3381fe681dd6f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Intel adopted xx_DEVFN_xx naming for macros expanding to
PCI_DEVFN() starting with apollolake. The ones named
xx_DEV_FUNC are being renamed, or dropped, if they
were generally not used at all for a platform.
Change-Id: I6ead2bc5e41a86c9aeef730f5664a30406414c8c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35730
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Let `sconfig` output a C header file with the symbol names that we
generate since 5e2a2cd5e7 (util/sconfig: Expose usable PCI and PNP
device names).
We add another command line argument for the path to the header
file. As the file is similar in nature to our `config.h` we simply
put it in $(obj)/ too.
Change-Id: I8f87288c82f2844b61eba6534797a42b978b47bb
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Auto-discoverable PCI devices do not require field .enable_dev
of chip_operations to be set. They are matched with PCI drivers
by the use of PCI vendor and device ID fields.
The name given for the chip_operations struct must match the
pathname the way it is present in the devicetree.cb files. If
there was no match, util/sconfig would currently choose to
use the empty weak declaration it creates in static.c file.
Change-Id: I684a087a1f8ee4e1a5fd83450cd371fcfdbb6847
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
ONBOARD_MICRON_MEM and ONBOARD_SAMSUNG_MEM are available.
These are used to determine if Samsung or Micron onboard memory is
assembled. This can not detected run-time.
Choice is replaced by one config.
Only oldest HW revision contains Samsung module, so set
CONFIG_ONBOARD_SAMSUNG memory to default No.
BUG=N/A
TEST=Boot and verified on Facebook FBG-1701
Change-Id: Id65e92bd4b8d4fe3a6b87dec9bf77e3a62e1be96
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This splits the x11-lga1151-series' documentation into a generic and a
board specific section as a preparation for CB:35427.
Additionally this adds some more information on the x11ssh board.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I40ddd0b5cce0b1a3306eae22fc0a0bc6b2a6263c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Before oprom is executed, no check is performed if rom passes verification.
Add call to verified_boot_should_run_oprom() to verify the oprom.
verified_boot_should_run_oprom() expects and rom address as input pointer.
*rom is added as input parameter to should_run_oprom() which must be parsed
to verified_boot_should_run_oprom()..
BUG=N/A
TEST=Created verified binary and verify logging on Facebook FBG1701
Change-Id: Iec5092e85d34940ea3a3bb1192ea49f3bc3e5b27
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Some VR parameter values for KBL-U with GT3 graphics are different from
values for other CPUs in this series [1]. However, GT3 iGPU will never
be detected, since the igd_id variable is compared with the LPC device
PCI ID. The patch fixes this bug.
[1] page 109, 7th Generation Intel(R) Processor Families for U/Y
Platforms and 8th Generation Intel(R) Processor Family for U Quad
Core and Y Dual Core Platforms. Datasheet, Volume 1. January 2019.
Document Number: 334661-006
Change-Id: I33527d90550a1de78c9375d3d3b0e046787a559b
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
According to the documentation[1], the Loadline in the unslased GT VR
domain should be 2 mOhms for KBL-U (2 Core, GT3 + OPC).
[1] page 109, 7th Generation Intel(R) Processor Families for U/Y
Platforms and 8th Generation Intel(R) Processor Family for U Quad
Core and Y Dual Core Platforms. Datasheet, Volume 1. January 2019.
Document Number: 334661-006
Change-Id: I433036e76d456a725ab27cf57c9bc2fe01a7ace1
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35781
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adds missing Intel HD/Iris iGPU PCI IDs for Kaby Lake processors and
updates the platform report for these devices.
These changes are in accordance with the documentation:
[*] page 10, Intel(R) Open Source HD Graphics and Intel Iris(TM) Plus
Graphics for the 2016 - 2017 Intel Core(TM) Processors, Celeron(TM)
Processors, and Pentium(TM) Processors based on the "Kaby Lake"
Platform. Programmer's Reference Manual. Volume 4: Configurations.
January 2017, Revision 1.0
Doc Ref # IHD-OS-KBL-Vol 4-1.17
[*] Linux kernel sources: include/drm/i915_pciids.h
Change-Id: I1cd1e4ab82f756141f8f13edf1c17f726166dffb
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
According to the DC Current Specifications [1], the current limit for
the graphical VR domain (Iccmax_gt) isn't same for different Kaby Lake S
CPUs. This value should depend on the iGPU model and processor TDP:
+---------------------+-----+------------+
| Segment | TDP | Icc_max GT |
+---------------------+-----+------------+
| Dual Core GT2/GT1 | 35W | |
| Dual Core GT2 | 51W | 48 A |
| Dual Core GT1 | 54W | |
+---------------------+-----+------------+
| Quad Core GT2 | 35W | 35 A |
+---------------------+-----+------------+
| Quad Core GT2 | 65W | 45 A |
| Quad Core GT2 K-SKU | 91W | |
+---------------------+-----+------------+
This patch adds the remaining Iccmax_gt current limit values from the
documentation [1].
[1] 7th Generation Intel(R) Processor Families for S Platforms and
Intel(R) Core(TM) X-Series Processor Family Datasheet, Volume 1,
December 2018, Document Number: 335195-003
Change-Id: I19766e4f8fab6b48565b65ed4cf13efbc213e654
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
No support is available in mainboard.
Add support to mainboard:
- Add mb_log_list[]
- Add routine mb_crtm()
BUG=N/A
TEST=Boot Embedded Linux 4.20 and verify logging on Facebook FBG-1701
Change-Id: I5120ffb6af0b41520056e1773f63b7b2f34a2460
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
The vendorcode for verified boot is uploaded, but not used by a mainboard.
Add support to the mainboard for verified boot.
The items to be verifed are placed in board_verified_boot.c
BUG=N/A
TEST=Boot Embedded Linux 4.20 and verify logging on Facebook FBG-1701 rev 0-2
Change-Id: I3ea0a95287977df0dea13e05acedd5406538a6ee
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33463
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create verified boot support, which includes verifiication of bootblock.
This feature use the vendorcode/eltan/security/lib.
cbfs_locator is used to init the verified boot support.
vendor_secure_prepare() and vendor_secure_locate() are used to preform the
required action in each stage.
The next lists will be used for verification:
* bootblock_verify_list
* postcar_verify_list
* romstage_verify_list
* ramstage_verify_list
BUG=N/A
TEST=Created binary and verify logging on Facebook FBG-1701
Change-Id: If6c1423b0b4a309cefb7fe7a29d5100ba289e0b4
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Create measured boot.
This feature uses the vendorcode/eltan/security/lib.
Measure boot can work with and without Verified boot enabled.
The function mb_measure() is starting point for the support. This
function will be called by the common Verified boot code.
BUG=N/A
TEST=Created binary and verify logging on Facebook FBG-1701
Change-Id: I7f880a17e240515dd42d57383b5ddddf576985b0
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Updating from commit id 42cdeb93:
2019-09-13 12:09:21 +0000 - (Merge "stm32mp1: manage CONSOLE_FLAG_TRANSLATE_CRLF and cleanup driver" into integration)
to commit id ace23683:
2019-09-27 09:54:27 +0000 - (Merge changes from topic "ld/stm32-authentication" into integration)
This brings in 83 new commits.
Change-Id: I273b5014db76d307d8735d78a8fdd5db3d07146c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Previously all boards using eSPI for the Chrome EC just called it
LPC as the code for the chrome EC is the same between the two
busses.
I'm adding a new Kconfig symbol to specify eSPI, so switch the
boards that actually use eSPI to that symbol and add the LPC
symbol to all the others.
The EC_GOOGLE_CHROMEEC_LPC symbol will no longer default
to enabled for x86 platforms, so one symbol or the other needs to be
specified for each platform.
BUG=b:140055300
TEST=Build tested only.
Change-Id: Icf242ca2b7d8b1470feda4e44b47a2cdc20680f2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add new config option to validate the Intel firmware descriptor against
the fmap layout. This will prevent a firmware descriptor from being used
that could corrupt regions of the bootimage in certian circumstances.
BUG=chromium:992215
TEST=Build firmware image with mismached decriptor and fmp
Without VALIDATE_INTEL_DESCRIPTOR set firmware builds
With VALIDATE_INTEL_DESCRIPTOR set error is shown with mismached
regions
Change-Id: I9e8bb20485e96026cd594cf4e9d6b11b2bf20e1f
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add an option to ifdtool which validates that the flash regions defined
in the descriptor match the coresponding areas in the FMAP.
BUG=chromium:992215
TEST=Ran 'ifdtool -t' with a good bios image and verify no issues
run 'ifdtool -t' with a bad bios image and verify expected issues
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Idebf105dee1b8f829d54bd65c82867af7aa4aded
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There's a recurring pattern of reading cbtable entries that point into
cbmem entries. Move that pattern into its own function.
Coccinelle patch used for this:
@@
identifier T, T2;
expression TARGET;
@@
-struct cb_cbmem_tab *const T2 = (struct cb_cbmem_tab *)T;
-TARGET = phys_to_virt(T2->cbmem_tab);
+TARGET = get_cbmem_ptr(T);
Change-Id: I7bd4a7ad8baeeaebf0fa7d4b4de6dbc719bc781f
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
An original code had a wrong register address 0x27 for AHCI BAR.
The value was aligned incidentally by the code specific of
the pci_read_config32 function to the correct address 0x24.
All 0x24 values in sata.c were changed to the symbolic name
PCI_BASE_ADDRESS_5 and the code was optimized.
An equivalent code was tested on a real hardware.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Change-Id: I33509befe86ff6e333c559c87a0f45886d737df9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35737
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Connected 4K monitor is not configured at max resolution. The
framebuffer size is too small.
Increase the framebuffer size to 64MB. This is sufficient for max
configuration of 1 HDMI monitor combined with internal LCD panel.
BUG=N/A
TEST=4K HDMI monitor and LCD working fine on Facebook FBG-1701
Change-Id: I25d2cd696830fc5bda84ea2b87538f526373998e
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Updating from commit id 860fe2962:
2018-12-29 05:45:29 -0800 - (mt_scp/ipi: Support host command.)
to commit id a1afae4e0:
2019-10-02 11:47:45 +0000 - (juniper: initial setup)
This brings in 1723 new commits.
Change-Id: Ieb4f00b21a4354bb634c3427c73260123b54ac2a
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Updating from commit id ce228ee:
2019-07-02 11:11:08 +0530 - (include: Bump-up version to 0.4)
to commit id e561c63:
2019-10-02 17:03:58 +0530 - (lib: Fix coldboot race condition observed on emulators/simulators)
This brings in 44 new commits.
Change-Id: Ide6e3c2bb98e79750b40a9b8ca9f2f1d2c123628
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Updating from commit id e6700f4c:
2019-08-13 04:36:52 +0000 - (vboot: update vboot2 functions to use new vb2_error_t)
to commit id b2c8984d:
2019-10-01 06:01:59 +0000 - (vboot: fix compile error with MOCK_TPM)
This brings in 71 new commits.
Change-Id: Id7cefa3ad5b30c955d18e469494fec32f6f58a48
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This tool downloads, caches and analyzes commits pushed to gerrit
for a specified range of commits. Currently it only works over SSH.
Data that is printed about the range of commits:
CSV Data about each individual commit:
- Commit ID
- Commit Date
- Author
- Commiter
- Submitter
- Lines added
- Lines removed
- Title
- Reviewers
It then prints the analysis it did on the data:
- Total Commits
- Total lines added
- Total lines removed
- Total difference
- Authors - Number of commits
- Total Authors
- Authors - Lines added
- Authors - Lines removed
- Reviewers - Number of patches reviewed
- Submitters - Number of patches submitted
The script relies on a number of perl modules
which must be installed separately.
Change-Id: I74896a97b5fe370c0b08562ac85d29435e438a31
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/14225
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Ubuntu 19.04 will fail looking for aclocal-1.15 if the scripts
are not regenerated because 19.04 ships with 1.16.
There are not enough eyes to roll when working with GNU autotools.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I4aa9f520499930ffc984ab0b0144c9c6b2e544a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Intel adopted xx_DEVFN_xx naming for macros expanding to
PCI_DEVFN() starting with apollolake. The ones named
xx_DEV_FUNC are being renamed, or dropped, if they
were generally not used at all for a platform.
Change-Id: Ice1062d10b793dcbeb5b2ce9e2788fd3b6b6250b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35728
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The previously provided device path made no difference, all
integrated PCI devices point back to the same chip_info
structure.
Change reduces the exposure of various SA_DEVFN_xx and
PCH_DEVFN_xx from (ugly) soc/pci_devs.h.
Change-Id: Ibf13645fdd3ef7fd3d5c8217bb24d7ede045c790
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Two fields of struct sdram_params are renamed for future CL of DRAM full
calibration. Field 'impedance' is also removed.
BUG=none
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: I2f9673fd5ea2e62ee971f0d81bdd12aaf565e31c
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35738
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create documentation on padmelon, including how to program the SPI. Also
include an index.md pointing to the documentation, as currently there's no
maiboard documentation folder for AMD.
BUG=none.
TEST=none.
Change-Id: I1a684c1acd3fb9441df71e2bc0fffa6131148b98
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Because vcore is the power of ddrphy in the soc, DRAM DVFS needs to be
calibrated with different vcore voltages to get correct parameters.
A new API is added to allow changing vcore voltage.
BUG=b:80501386
BRANCH=none
TEST=measure vcore voltage with multimeter
Change-Id: Ic43d5efe7e597121775dc853a3e2a08ebc59657d
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33391
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make intel_ht_sibling() available on all platforms.
Will be used in MP init to only write "Core" MSRs from one thread
on HyperThreading enabled platforms, to prevent race conditions and
resulting #GP if MSRs are written twice or are already locked.
Change-Id: I5d000b34ba4c6536dc866fbaf106b78e905e3e35
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
A missing definition of gameport base (PNP io 0x60) will cause
an automatic address assignment during PCI/PNP enumeration, which
won't obey limit 0x7ff. This will cause the enumeration to fail
as other devices already have the values enabled.
The symptoms are: not working USB, PS/2, garbled UART console,
not working PCIe GPUs and crashes. Probably because of wrongly
assigned IO ports.
Example of log (shortened):
Done reading resources.
Setting resources...
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.0 1c * [0x0 - 0xfff] io
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.1 1c * [0x1000 - 0x1fff] io
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.2 1c * [0x2000 - 0x2fff] io
!! Resource didn't fit !!
aligned base 400 size 10 limit 2e7
40f needs to be <= 2e7 (limit)
PCI: 00:1f.2 20 * [0x3080 - 0x308f] io
!! Resource didn't fit !!
...
ERROR: PCI: 00:02.0 14 io size: 0x0000000008 not assigned
...
ERROR: PCI: 00:1f.2 10 io size: 0x0000000008 not assigned
ERROR: PCI: 00:1f.2 14 io size: 0x0000000004 not assigned
ERROR: PCI: 00:1f.2 18 io size: 0x0000000008 not assigned
ERROR: PCI: 00:1f.2 1c io size: 0x0000000004 not assigned
ERROR: PCI: 00:1f.2 20 io size: 0x0000000010 not assigned
...
PCI: 00:1b.0 subsystem <- 8086/27d8
PCI: 00:1b.0 cmd <- 102
PCI: 00:1c.0 bridge ctrl <- 0003
PCI: 00:1c.0 subsystem <- 8086/27d0
PCI: 00:1c.0 cmd <- 107
PCI: 00:1c.1 brids70c01mcu0PeC: 0
dV0i8s0immicrocode: upd10a00000y0025 x666600CPU physiaB 0 0 e k
MTRR cheaeu60zeAttemfWaiting for 1st Sot AP: slot 1 apic_L0ecl0zsax a
aInitiNntt kac:oIG0 Ua dUrSGSGL Ct0C07fintel_vga_int15_h
VGA Option ROM wa7..Azalia0Azalia: codkAbCiPCI: 00:1c.0 init finished
We can see the ports probably started to collide after the activation
of 00:1c.0 device. A debug run with compiled SPEW shows the problem
with enumeration:
PCI: 00:1f.1 18 * [0x50b8 - 0x50bf] io
PCI: 00:1f.2 10 * [0x50c0 - 0x50c7] io
PCI: 00:1f.2 18 * [0x50c8 - 0x50cf] io
PCI: 00:1f.1 14 * [0x50d0 - 0x50d3] io
PCI: 00:1f.1 1c * [0x50d4 - 0x50d7] io
PCI: 00:1f.2 14 * [0x50d8 - 0x50db] io
PCI: 00:1f.2 1c * [0x50dc - 0x50df] io
PNP: 002e.7 60 * [0x50e0 - 0x50e0] io <-- gameport base
DOMAIN: 0000 io: base: 50e1 size: 40e1 align: 12 gran: 0 limit: 7ff done
Notice a weird base for DOMAIN, along with the limit.
Adding a definition of gameport (0x220) as a workaround fixes
the problems.
The gameport should be still disabled thanks to disable bits
(W83627THF datasheet is little bit chaotic). I didn't find any info
if the gameport is available on some pads of the motherboard.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Change-Id: Ie8e42552ac5e638e91e5c290655edcce1f64e408
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Implementation of ich_pci_dev_enable_resources() used to have
a custom implementation to program PCI subsystem IDs for the
(legacy) PCI bus bridge.
With the local implementation removed, we no longer need the
custom .enable_resources callback.
Change-Id: I6f73fd0e4d5a1829d1555455c9a143f1d18a6116
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Petr Cvek <petrcvekcz@gmail.com>
The simple PCI config accessors are always available
under names pci_s_[read|write]_configX.
We have some use for PCI bridge configurations and
resets in romstages, so expose them.
Change-Id: Ia97a4e1f1b4c80b3dae800d80615bdc118414ed3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Many supported SST flashes use the AAI OP (0xad) to write.
TESTED on Thinkpad X60 with SST25VF016B, flashrom can use AAI_WRITE op
with locked down SPIOPS.
Change-Id: Ica72eda04a8d9f4e563987871b1640565c6e7e12
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35537
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Allow to set a lower temperature limit, as the currently hard-coded
25C may be to low for a given temperature sensor. Also enable smoo-
thing, currently hard-coded to the maximum interval of 35s, and set
the hysteresis value.
Change-Id: I5fde1cf909e8fbbaf8a345790b00c58a73c19ef8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The existing Kconfig code made SMBIOS_PROVIDED_BY_MOBO depend
on VENDOR_LENOVO. Thus, it couldn't be selected by boards from
other vendors. So we add another Kconfig that selects it
here.
NB. It's still unclear how the two drivers in this directory
are related (at24rf08c and lenovo_serial). From the code, it
doesn't look like the latter belongs here.
Change-Id: Iaa5c5a584f2a5e2426352ec6aa681f99a55efa49
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
According to the documentation [1], SKL-H Halo GT4E (Iris Pro Graphics
P580) PCI ID should be 0x193B.
[1] page 11-12, Intel(R) Open Source HD Graphics, Intel Iris(TM)
Graphics, and Intel Iris(TM) Pro Graphics, Programmer's Reference
Manual. Volume 4: Configurations. May 2016, Revision 1.0
Doc Ref # IHD-OS-SKL-Vol 4-05.16
Change-Id: Id62fe3ec26779d51b748efd271db565ade1e3ee0
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The CRC result is treated as a signed value, and so in certain
situations, the calculated value for the last four digits will not
be correct. Ensure that the CRC is treated as an unsigned 32-bit
value prior to converting the last 4 decimal digits to a string.
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: I92f9ce1ceb7450f90b89c94e0ace6f79a9419b42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35604
Reviewed-by: Andrew McRae <amcrae@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Use all caps for variables.
* Use a single exit code for failures.
* No need to popd before exiting the script.
* Do ${var,,} and ${var^^} into variables instead of using it everywhere.
* Add more punctuation in comments.
* Specify LC_ALL=C so that upper/lower case show the desired behavior.
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: I63aa0aa633f36b9543e809fc42fac955da5960a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrew McRae <amcrae@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
To support mt8183 power saving during suspend to RAM, this patch loads
SPM firmware to support SPM suspend. SPM needs its own firmware to do
these power saving in the right timing under correct conditions. After
linux PM suspends, SPM is able to turn off power for the last CPU and do
more power saving for the SoC such as DRAM self-refresh mode and turning
off 26M crystal.
BUG=none
BRANCH=none
TEST=suspend/resume passes for LPDDR4 3200
Change-Id: I3393a772f025b0912a5a25a63a87512454fbc86e
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Make sure to match devices on the root bus only. This fixes an issue
where the SoC returned "MCHC" as ACPI name for devices behind bridge
devices, as the DEVFN matched.
Fixes observed "ACPI exception: AE_NOT_FOUND" in dmesg, as the ACPI
path no longer contains invalid names.
Tested on Supermicro X11SSH-TF.
Change-Id: I6eca37a1792287502a46a90144f2f0d8e12ae5d4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The CONFIG_GBB_HWID can be generated automatically now so we can remove
the test-only HWIDs set in board config files.
BUG=b:140067412
TEST=Built few boards (kukui, cheza, octopus) and checked HWID:
futility gbb -g coreboot.rom
Change-Id: I4070f09d29c5601dff1587fed8c60714eb2558b7
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35635
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The HWID in vboot GBB is an identifier for machine model. On Chrome OS,
that should be provisioned in manufacturing process (by collecting real
hardware information), and will be checked in system startup.
For bring up developers, they usually prefer to generate a test-only
string for HWID. However that format was not well documented and cause
problems. Further more, most Chromebooks are using HWID v3+ today while
the test-only HWID is usually v2. Non-Chrome OS developers may also
prefer their own format.
To simplify development process, the GBB_CONFIG now defaults to empty
string, and will be replaced by a board-specific test-only v2 HWID
automatically. Developers can still override that in mainboard Kconfig
if they prefer v3 or other arbitrary format.
BUG=b:140067412
TEST=Built 'kukui' successfully. Removed kukui GBB config and built
again, still seeing correct test HWID.
Change-Id: I0cda17a374641589291ec8dfb1d66c553f7cbf35
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The description.md and README.md was explicitly made for downloading or
extracting some resources, but we need to add more Chrome OS related
scripts soon; so the description should be revised.
Also changed README.md for better markdown style, for example
- Use #, ## to replace the old '-' headers
- Use code format for file names
- Use code block for example of shell execution
Change-Id: Icc3677fa318b03f4aee1b0f5fb13b2095f2afe64
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If VBOOT is used on a mainboard based on fsp_broadwell_de then VBOOT
needs to be able to write to its NV data which may be stored on the SPI
flash. Enable write access to the SPI flash on SoC level. If the
mainboard does not use VBOOT the linker will drop the extra code. The
benefit is that this code is at least compiled and therefore build
tested with fsp_broadwell_de.
Change-Id: I90a2d30f5749c75df2b286dce6779f10dde62632
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Internal pull up need to be enabled for GPD3 as power button pin for
PCH according cometlake pch EDS vol1 section 17-1. Without that pin will
stay floating and hook up XDP can cause system shutdown as power buttone
event will trigger.
BUG=N/A
TEST=Hook up XDP on drallion platform, able to boot up into OS and stay
at power up state.
Change-Id: Idd1befeb14a251b7c0542ca1f99049d07b28fb98
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
The filename chip.h has a special purpose with the generation
of static devicetree, where the configuration structure name matches
the path to the chip.h file. For example, soc/intel/skylake/chip.h
defines struct soc_intel_skylake_config.
The renamed file did not follow this convention and the structure it
defines would conflict with one defined soc/intel/common/chip.h if such
is ever added.
Change-Id: Id3d56bf092c6111d2293136865b053b095e92d6b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
CONFIG_CBFS_SIZE should only be used as a parameter to generate the
default FMAP.
This also swaps around FMDFILE and CBFS_SIZE to avoid that the
CBFS_SIZE entry disappears when filling in the FMDFILE entry below it.
One advantage is that if code references CONFIG_CBFS_SIZE the jenkins
buildtest will most likely fail as many boards provide an FMD file.
Change-Id: Ic7926e1638d7fb49ba61af28d682315786c3c39e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
CB:35377 changed the behavior of find_fmap_directory() to return
pointer to CBMEM_ID_FMAP if fmap is cached in
cbmem. lb_boot_media_params() calls find_fmap_directory to add offset
of fmap in flash to coreboot table. However, because of the change in
behavior of find_fmap_directory(), it ended up adding 0 as the offset.
This change adds a new function get_fmap_flash_offset() which returns
the offset of fmap in flash. Ideally, all payloads should move to
using the FMAP from CBMEM. However, in order to maintain compatibility
with payloads which are not updated, ensure that fmap_offset is
updated correctly.
Since find_fmap_directory() is no longer used outside fmap.c, this
change also removes it from fmap.h and limits scope to fmap.c.
In a follow up patch, we need to push a change to libpayload to expose
the fmap cache pointer to lib_sysinfo.
BUG=b:141723751
Change-Id: I7ff6e8199143d1a992a83d7de1e3b44813b733f4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
dev_find_slot() can sometimes fail to return the desired device object
prior to full PCI enumeration. Comment the declaration and
implementation accordingly to help the user understand the problem and
avoid its usage.
Change-Id: I3fe1f24ff015d3e4f272323947f057e4c910186c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35632
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The vendor id option set here is useless as most SSVID registers get
filled with 0x8086 (their VID) by default, anyway.
Besides that the Kconfig option isn't meant for retrofit ports, cf.
commit 7e1c83e31b (Add Kconfig options to override Subsystem Vendor and
Device ID). The right place would be the devicetree.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: If67c679bb342f63096902535734106e4f1651118
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
coreboot toplevel makefile breaks when path to the coreboot directory
contains spaces.
This patch displays a reasonable message to the user whenever spaces
are found within the path to the coreboot direcrory.
This commit addresses coreboot ticket #179.
Change-Id: Id11deffa01ddca1ff9332d67c7aa33a382b4cdc7
Signed-off-by: Sourabh Kashyap <sourabhka@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35434
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All solid state devices have vendor id defined by JEDEC specification JEP106,
which originally allocated only 7 bits for it plus parity. When number of
vendors exploded beyond 126, a banking proposition came maintaining
compatibility with older vendors while allowing for 4 extra bits (16 banks)
through the introduction of the concept "Continuation code", denoted by the
byte value of 0x7f.
Examples:
0xfe, 0x60, 0x18, 0x00, 0x00 => vendor 0xfe of bank o
0x7f, 0x7f, 0xfe, 0x60, 0x18 => vendor 0xfe of bank 2
BUG=b:141535133
TEST=Build and boot grunt.
Change-Id: I16c5df70b8ba65017d1a45c79e90a76d1f78550c
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35589
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Most of the X11 boards with socket LGA1151 are basically the same boards
with just some minor differences like different NICs (1 GbE, 10 GbE),
number of NICs / PCIe ports etc.
There are about 20 boards that can be added, if there is a community for
testing.
To be able to add more x11 boards easily like x11ssm (see CB:35427) this
restructures the x11ssh tree to represent a "X11 LGA1151 series". There
were multiple suggestions for the structure like grouping by series
(x10, x11, x...), grouping by chipset or by cpu family.
It turned out that there are some "X11 series" boards that are
completely different. Grouping by chipset or cpu family suffers from the
same problem. This is why finally we agreed on grouping by series and
socket ("X11 LGA1151 series").
The structure uses the common baseboard scheme, while there is no "real"
baseboard we know of. By checking images, comparing logs etc. we came to
the conclusion that Supermicro does have some base layout which is only
modified a bit for the different boards.
X11SSH-TF was moved to the variants/ folder with it's gpio.h. As we
expect the other boards to have mostly the same device tree, there is a
common devicetree that gets overridden by each variant's overridetree.
Besides that some very minor modifications happened (formatting, fixing
comments, ...) but not much.
Documentation is reworked in CB:35547
Change-Id: I8dc4240ae042760a845e890b923ad40478bb8e29
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35426
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It is only called in ramstage. Even if it was called in
romstage, execution flow is such that BSP and AP CPUs
should not be able to enter update_microcode() routine
concurrently.
Also the Kconfig guarding the spin_lock() calls are not
selected nor are the lock variables declared for these
platforms.
Change-Id: I1c2e106f10e8420e942b3ed082c677c0db95557c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35586
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The script had a couple of bugs:
* It didn't create the required directory under variants/
* It was treating the wildcard as literal and so couldn't
find variant files to copy.
V.2: Drop verbose cp && fixup wild card usage.
Change-Id: Ie6f4179014b79ea45d0fcf406ca192046438dbf7
Signed-off-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrew McRae <amcrae@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
CB:29633 switched platform to use sb/common spi implementation,
which worked until CAR_GLOBAL was removed in CB:30506.
Revert the changes back to usage of CAR_GLOBAL in the common spi
driver so that flashconsole will work again in romsatge for
fsp_broadwell_de.
Test: verify flashconsole functional on out-of-tree Broadwell-DE board
Change-Id: I72e5db1583199b5ca4b6ec54661282544d326f0f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Fix regression from commit ecea916
cpu/intel/common: Extend FSB detection to cover TSC
MSR_EBC_FREQUENCY_ID (0x2c) was not defined for affected
CPU models and rdmsr() caused reset loops. Implementations
deviate from public documentation.
Change to IA32_PERF_STATUS (0x198) already used in i945/udelay.c
to detect FSB to TSC multiplier.
Change-Id: I7a91da221920a7e7bfccb98d76115b5c89e3b52e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The Razer Blade Stealth H2U is a KabyLake System using:
- Intel KBL 7500U
- ITE8528E SuperIO
- Intel 600P Series NVMe SSD
- Either four MT52L1G32D4PG (16GB) or MT52L512MB32D4PG (8GB)
of soldered memory in dualchannel mode
- (Optional) Touchscreen
- HDMI 2.0a via DP-1: Paradetech PS175
- AlpineRidge Thunderbolt 3 controller
- TPS65982 USB-PD power switch / multiplexer
Even though it has a 16MB chip equipped (W25Q128.V) only the first 8MB
are used and mapped via IFD. The rest is left empty (0xFF). The flash is
not secured in any way and can be read via flashrom. It should be the
source for this port's IFD and ME blobs.
Working:
- USB-A Ports left and right
- Speakers
- Touchscreen (USB)
- Onboard Keyboard in Linux
- NVMe SSD
- SeaBIOS, Tianocore and Grub Payloads
- Webcam
- Powersaving Modes
- Battery state and LID switch, sometimes slow to update.
- Touchpad (I2C-HID)
- Headphones
Not part of this commit:
- Thunderbolt / USB-C (Requires advanced EC signaling)
- Full HDMI support (Currently requires plugged connection at boot)
Change-Id: I7ede881d631e1863f07f5130f84bc3b8ca61a350
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
CONFIG_MAINBOARD_DEPTHCHARGE is used to override the Board
config for depthcharge which inherit from CONFIG_MAINBOARD_PART_NUMBER.
This is mainly to avoid depthcharge config duplication.
Signed-off-by: Selma BENSAID <selma.bensaid@intel.com>
Change-Id: I6cbc93ca38ad6deeca2c2fb7770024a24233b6f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
When accessing register with multiple bit fields, the common approach is
to use clrsetbits_le32, for example:
clrsetbits(®, (1 << 0) | (0x3 << 1) | (0x7 << 10),
(1 << 0) | (0x1 << 1) | (0x5 << 10));
This hard to maintain because we have to calculate the mask values
manually, make sure the duplicated shift (offset) was set correctly.
And it may be even worse if the value to set will be based on some
runtime values (that many developers will do a if-block with two very
similar argument list), and leaving lots of magic numbers.
We want to encourage developers always giving field names, and have a
better way of setting fields. The proposed utility macros are:
DEFINE_BITFIELD(name, high_bit, low_bit)
EXTRACT_BITFIELD(value, name)
WRITE32_BITFIELDS(addr, name, value, [name2, value2, ...])
READ32_BITFIELD(addr, name)
Where a developer can easily convert from data sheet like
BITS NAME
26:24 SEC_VIO
Into a declaration
DEFINE_BITFIELD(SEC_VIO, 26, 24)
Then, a simple call can set the field as:
WRITE32_BITFIELDS(®, SEC_VIO, 2);
That is much easier to understand than
clrsetbits_le32(®, 0x7 << 24, 0x2 << 24);
And to extract the value:
READ32_BITFIELD(®, SEC_VIO)
That is equivalent to:
(read32(®) & 0x3) >> 24
Change-Id: I8a1b17142f7a7dc6c441b0b1ee67d60d73ec8cc8
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35463
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- configure DMA fw_cfg
- add support to read using fw_cfg_dma
- provide fw config version id info in logs
BUG=N/A
TEST=Build and boot using qemu-i440fx.
Change-Id: I0be5355b124af40aba62c0840790d46ed0fe80a2
Signed-off-by: Himanshu Sahdev <himanshusah@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Devices using eMCP may run at a high DRAM frequency (e.g., 3600Mbps)
while those with discrete DRAM can only run at 3200Mbps. This patch
enables 3600Mbps for eMCP DDR for better system performance.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly and stress test passes on Kukui
Change-Id: Iab6a9c2c390feeb9497b051a255b29566909e656
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Drop unused CNF2_LPC_EN, as there is no device which uses IO 0x4e/4f.
Do not use the mainboard model to set COMA_LPC_EN. Make use of
NO_UART_ON_SUPERIO instead, as it is more future-proof.
Change-Id: Iac49250b0f509a42012f82db8aa85ba85559c66f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Read-modify-write needs to access the same register. Numerically
both used defines are 0x3e, while register implementations are
not identical but only similar.
Change-Id: I9348b855320f86868e2d3ef76d3b8d7a4ab7fae0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner
Currently "DIMM numbers" increase monotonically for all the channels. However,
commonly DIMMS are numerated on per-channel basis. This change makes numeration
match the convention.
TEST=on OCP monolake, run dmidecode tool and see that "Locator" field matches
expectation.
Change-Id: I3e7858545471867a0210e1b9ef646529b8e2a31c
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35318
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the new SPI code from common folder, delete spi.c. SPI related macros
must be single defined, in southbridge.h if they are used by files other
than the common SPI code, fch_spi.h if they are only used by the common
SPI code. The only exception is SPI_FIFO_DEPTH which must be in southbridge.h,
because it can change between SOC.
BUG=b:136595978
TEST=None, code already tested with grunt.
Change-Id: I68008ce076d348adbdabf7b49cec8783dd7134b4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Use the new SPI code from common folder, delete spi.c. SPI related macros
must be single defined, in southbridge.h if they are used by files other
than the common SPI code, fch_spi.h if they are only used by the common
SPI code. The only exception is SPI_FIFO_DEPTH which must be in southbridge.h,
because it can change between SOC.
BUG=b:136595978
TEST=Build and boot grunt using new SPI code, with debug enabled. Check
output.
Change-Id: I639973d993316a10daa7564462e689b2c183f536
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Create a new SPI code that overrides flash operations and uses the SPI
controller within the FCH to its fullest.
Reference: Family 15h models 70h-7Fh BKDG revision 3.06 (public)
BUG=b:136595978
TEST=Build and boot grunt using this code, with debug enabled. Check
output.
Change-Id: Id293fb9b2da84c4206c7a1341b64e83fc0b8d71d
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
With the support of various algorithms and banks in tlcl_extend(),
digest_algo parameter of tpm_extend_pcr() started defining the target
PCR bank in TPM2 case.
The OS expects coreboot to extend the SHA256 bank of BOOT_MODE_PCR.
The value that the OS expects coreboot to extend into BOOT_MODE_PCR
is the SHA1 digest of mode bits extended to the length of SHA256 digest
by appending zero bytes.
Thus the correct value for digest_algo passed into tpm_extend_pcr() for
BOOT_MODE_PCR is TPM_ALG_SHA256.
This didn't matter until adding the support for multiple digest introduced
by patches like https://review.coreboot.org/c/coreboot/+/33252, as
tlcl_extend always used SHA256 bank before.
Change-Id: I834fec24023cd10344cc359117f00fc80c61b80c
Signed-off-by: Andrey Pronin <apronin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35476
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As we redirect all `dd` output to /dev/null (it would clutter the
console otherwise), there is no error message if a binary to be
added isn't found. If we add them as dependency, OTOH, `make` will
complain properly.
Change-Id: I40c3979b84341cb88c7e9a5084c1a97230ea5503
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33327
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add more DRAM frequency bootup to support DRAM frequencies 1600Mbps,
2400Mbps, 3200Mbps and 3600Mbps.
BUG=b:80501386
BRANCH=none
TEST=Memory test passes on eMCP platform
Change-Id: Ic1378ca43fb333c445ca77e7dc0844cdf65f2207
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch implements the dram init setting by replacing the hard-coded
init sequence with a series of functions to support calibration for more
frequencies. These functions are modified from MediaTek's internal DRAM
full calibration source code.
BUG=b:80501386
BRANCH=none
TEST=1. Kukui boots correctly
2. Stress test (/usr/sbin/memtester 500M) passes on Kukui
Change-Id: I756ad37e78cd1384ee0eb97e5e18c5461d73bc7b
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The bus variable doesn't live outside the scope of this function, and is
only used as a convenient way for passing the pointers to all the
sub-functions, so it doesn't need to be allocated. Put it on the stack
instead. A similar fix for ipq806x was done in 0f33d8c29a
(soc/qualcomm/ipq806x: Remove unnecessary allocation).
Change-Id: Ibb1129b92e38a105e100f59e03d107de340b925c
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1294801
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Intel's EDS says "1 = GPIO Driver Mode. GPIO input event updates are
limited to GPI_STS. GPI_GPE_STS, GPI_NMI_STS and/or GPI_SMI_STS updates
are masked." Therefore, the GPI_GPIO_DRIVER_SCI option for pad
configuration is meaningless, as any GPE will be masked if the GPIO
driver is set as owner.
Change-Id: Ia0cd0041dfc985cbe388cb89a4026038c7fb4383
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35460
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A closer read of the EDS indicates that when GPIO Driver mode is
selected, GPIO input event updates are limited to GPI_STS only.
GPI_GPE_STS updates are therefore masked, and we don't want to enable
this behavior. It masks the GPE and does not allow us to see this GPE
as a wake source, obscuring the reason that the system woke up.
Also switch the IRQ from level-triggered to edge-triggered,
otherwise the system will auto-wake from any sleep state when the
pen is ejected from the garage.
BUG=b:132981083
BRANCH=none
TEST=Wake up system from S0ix using pen eject, verify that mosys
eventlog shows GPE#8 as the S0ix wakeup source. Wake up system from S3
via pen eject, and verify that the wakeup source shows as GPE#8.
Change-Id: If017e12e23134f5cfed7cbb6047cc9badd9bf7e8
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35459
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove duplicate headings, move vendor sections that were placed
amidst other vendor hierarchies, and while we are at it, sort it
alphabetically.
Change-Id: I1f684deac3bbf98e8584089be05daf1c73e74a2d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35462
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current clang-format configuration is completely broken. It forces
one to change the code style of patches before pushing them, only to
find out that checkpatch now complains about it. This means newcomers
get scared away, and developers only get angered and frustrated about
it, and end up working around clang-format's requirements anyway.
For now, make clang-format's complaints non-fatal, reducing them to text
noise. However, since clang-format is currently unusable, reverting it
out would be preferred.
Change-Id: Iffa8934efa1c27c04e10545f66d8f9976e74c367
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
To create a new variant of the hatch baseboard, we need to
add the variant's GBB_HWID and other information to Kconfig
and Kconfig.name, and set up a skeletal build based on the
hatch baseboard.
BUG=b:140261109
BRANCH=none
TEST=``./create_coreboot_variant.sh sushi && git show``
Kconfig will have three new lines for the SUSHI variant, and
Kconfig.name will have an entirely new section.
New files created are:
variants/sushi/Makefile.inc
variants/sushi/overridetree.cb
variants/sushi/include/ec.h
variants/sushi/include/gpio.h
variants/sushi/include/variant/acpi/dptf.asl
Also run the script with an existing board name to verify that you
can't create a variant that already exists.
Change-Id: I1a5b9c8735faafebb2e4e384cb3346867d64c556
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Initialize the input_hertz and uart_pci_addr fields of the lb_serial
struct to prevent later undefined reads in lb_add_serial(). This was
done for exynos5420 in commit ff94e00362 (soc/samsung/exynos5420/uart.c:
Init new serial struct variables), and this patch finishes the rest.
Note that not all of the drivers can have the UART PCI address
configured at build time, so a follow-up patch will be needed to correct
those ones.
Change-Id: I733bc8185e2f2d28a9823495b53d6b09dce4deb1
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1354778
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34548
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Below new functions are added:
* send_hmrfpo_enable_msg() - Sends HMRFPO Enable command to CSE. This
API sets ME in SEC_OVERRIDE mode. The mode prevents CSE to execute SPI I/O
cycles to CSE region, and unlocks the CSE region to perfom updates to it.
* send_hmrfpo_get_status_msg() - Sends HMRFPO Get Status command to CSE
TEST=Verified sending HMRFPO_ENABLE & HMRFPO_GET_STATUS HECI commands on
CML RVP & hatch board
Change-Id: I559bc4641e12df7ed39b1c97097bf068f9a232db
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Add DPTF based thermal control for ambient sensor for CML based
Helios system. Also, update other sensor names information.
BUG=b:139335207
BRANCH=None
TEST=Build and Boot on Helios board and check all sensor details.
Change-Id: I322d53536fbdf6db70f5a24afb322d9f206eaeac
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update DPTF thermal temperature threshold values for CML based
Helios system. This updates CPU active cooling temperature
threshold to appropriate values which addresses the issue of
running the Fan at lower CPU temperature as per bug.
Also, added active cooling temperature thresholds for other
TSR sensors.
BUG=b:141087272
BRANCH=None
TEST=Build and boot on Helios board to check the fan functionality.
Change-Id: I5c8502f8c9e6121c18024d2a8d5a4f7680797b8d
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35446
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In interactive payloads, the USB stack's poll procedure is implicitly
called from the UI loop. Since all USB control transfers are handled
synchronously, polling hubs with these slows the UI significantly down.
So switch to interrupt transfers that are done asynchronously and only
perform control transfers when the hub reported a status change.
We use the interrupt endpoint's max packet size instead of the theo-
retical transfer length of `(bNrPorts + 1) / 8` as Linux' code mentions
hubs that return too much data.
Change-Id: I5af02d63e4b8e1451b160b77f3611b93658a7a48
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/18499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add SKU#18 to config power sequence below:
GPIOs related to power sequnce are
GPIO_67 - EN_PP3300
GPIO_117 - FULL_CARD_POWER_ON_OFF
GPIO_161 - PLT_RST_LTE_L
1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161
2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67
3. Power reset:
- keep GPIO_67 and GPIO_117 high and
- pull down GPIO_161 for 30ms then release it.
BUG=b:134854577,b:137033609
BRANCH=octopus
TEST=build
Change-Id: I58e07518f6daaf608684c9fa1b1c88fc592ea117
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
../bd82x6x/early_usb.c: While ibexpeak needs an equivalent of this
code, it is not currently hooked up.
../common/gpio.c: Already linked in common/Makefile.inc
Change-Id: I980601e2302f2c412e823fef5fb9a69b9e151322
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35437
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some T430s variants have a Thunderbolt controller wired to PCIe port
The controller hotplugs itself to the chipset when a downstream device
is hotplugged into it, so the hotplug capability should be enabled on
PCIe port #5.
TODO: find the correct gpio pin to detect the Thunderbolt controller
at runtime.
There are 3 variants of mainboard for Thinkpad T430s: Basic type
(Wistron LSN-4 11263-1), Boards with an additional discreet GPU,
Boards with an additional TB controller (Wistron LSN-4 11271-1),
each of which has a different schematic.
The gpio27 on the last type is set as set as GPIO-INPUT, compared
with GPIO-OUTPUT-HIGH on the basic type boards.
Change-Id: I61f41db100f398069e50e2da8a378b3a8d1c84bf
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Fix regression after commit
21160a7 Add definition for ENV_ROMSTAGE_OR_BEFORE to <rules.h>
Builds with VBOOT_STARTS_IN_ROMSTAGE=y would evaluate
ENV_ROMSTAGE_OR_BEFORE incorrectly for verstage-class.
Follow-up changes for CBMEM console and timestamps, where
defined(__PRE_RAM__) tests are replaced, are likely to have
caused regressions such that VBOOT console and timestamps
are missing.
Change-Id: Idc274409c495efea95eeecd0538b2f8b847970ad
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
For pcengines/apu2 variants we do not even send
DRAM ready message to PSP.
Possibly some GFX/DRM depends of running PSP but
these devices are headless. And we don't support
fTPM inside PSP either.
Reduces blob footprint in SPI from 466 KiB to 234KiB.
Change-Id: I803722171cba9b3601fb0b4a2c0e984566f435ab
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Move it above 'AGESA' to increase the maximum
continuous free space in CBFS from 5.3 MiB to 5.8 MiB.
Also fixes build for cases where CBFS_SIZE < ROM_SIZE,
thus allowing FMAP regions.
NOTE: Due to off-by-one error in binaryPI, offset
0xFFFA0000 that amdfwtool advertises fails
for xHCI firmware loading.
Change-Id: Ic78520f4248f0943769e66a8825911c0ddcc368c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Additional cleanup - Unify "Inc" to "Inc." and "LLC." to "LLC"
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ie03a3ce1f6085494bd5f38da76e2467970cf301a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
We generally try to stay away from ascribing attributes to (future)
devs. "Rookie guide" refers to the reader, while "tutorial" refers
to the material.
In the same spirit, move from "lessons" to "parts". It's not school :-)
Change-Id: I11a69a2a05ba9a0bc48f8bf62463d9585da043ec
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change overrides USB port settings for kohaku.
Some port settings are same with baseboard, but I'd like to describe all
settings here to be aware of current setting and usage of USB ports on
kohaku.
BUG=none
BRANCH=none
TEST=built and measured SI of USB ports internally
Change-Id: I5ac05485d1cd94416e5a0aecf7fa6769bd7c9e84
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Every vga init implementation needs to cache the framebuffer state
to be able to fill the lb_framebuffer struct later on in the
fill_lb_framebuffer call. Showing the bootsplash afterwards
guarantees to have the same interface into all the vga drivers.
This is by far from ideal, as it only allows for a single driver at
compile-time and should be adapted in the future.
It was tested on the wip razer blade stealth using vgabios @ 1280x1024
and also in Qemu @ 1280x1024.
By default the qemu framebuffer will be initialized in 800x600@32.
This can be overwriten by configuration by setting
CONFIG_DRIVERS_EMULATION_QEMU_BOCHS_{X,Y}RES .
Change-Id: I4bec06d22423627e8f429c4b47e0dc9920f1464e
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch uprevs the Arm Trusted Firmware submodule to the new upstream
master (commit 42cdeb930).
Arm Trusted Firmware unified a bunch of stuff related to BL31 handoff
parameters across platforms which involved changing a few names around.
This patch syncs coreboot back up with that. They also made header
changes that now allow us to directly include all the headers we need
(in a safer and cleaner way than before), so we can get rid of some
structure definitions that were duplicated. Since the version of entry
point info parameters we have been using has been deprecated in Trusted
Firmware, this patch switches to the new version 2 parameter format.
NOTE: This may or may not stop Cavium from booting with the current
pinned Trusted Firmware blob. Cavium maintainers are still evaluating
whether to fix that later or drop the platform entirely.
Tested on GOOGLE_KEVIN (rk3399).
Change-Id: I0ed32bce5585ce191736f0ff2e5a94a9d2b2cc28
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
In FSP-S, the driver constructs its pointer to UPD using the offset
in the header. Similarly, use the header's cfg_region_size for
allocating memory and copying the default configuration.
Add sanity checks for unexpedted configuration and UPD header
conditions.
TEST=Verify OK on Mandolin, verify a mock error condition
BUG=b:140648081
Change-Id: I20fad0e27a2ad537898b6d01e5241e1508da690c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Leverage already used eax register in bootblock_protected_mode_entry.
Avoid another register ebx just for preserving eax value as it is not
needed and is not used at all after moving the value into mm0.
Allow EBX to be preserved for other usage.
Change-Id: Ia668b78f2f97cf026692f1fe63ff8a382a162474
Signed-off-by: Himanshu Sahdev <himanshusah@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35292
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Even though GT7375P programming guide rev0.4 only requires a reset delay
of 120ms, in practice, we have to increase the reset delay to 500ms, or
Goodix FW update would fail.
This is a workaround. In the long run, we hope Goodix can fix the power
sequence in touch firmware.
BUG=b:138795891, b:138796844
TEST=boot helios board and verify Goodix FW update succeeded
Signed-off-by: Philip Chen <philipchen@google.com>
Change-Id: Ic0049bf240de0a1c7f1b1f39bf155d48bb76fb86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35350
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Replace the raw register definitions with device numbers and macros
for determining the register offsets. Rewrite the source to refer
to AOAC device numbers instead of a structure.
Remove the calculated offset for the console UART. Picasso's UARTs
are not contiguous so handle them separately.
Change-Id: Iffc87f39ebe38394a56d41bb0940e9701fd05db9
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
PchPwrOptEnable FSP UPD is for internal testing and not really available
in externally released FSP source hence assigning this UPD using devicetree
config dmipwroptimize doesn't do anything.
TEST=Build and boot sarien/arcada.
Change-Id: I6da2a088fb697e57d12008fa18bd1764b3da7765
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Host FW status 1 (FWSTS1/HFSTS1) register definition is common across SoCs,
hence move it to common. Also add below helper function,
* wait_cse_sec_override_mode() - Polls ME status for "HECI_OP_MODE_SEC_OVERRIDE".
It's a special CSE mode, the mode ensures CSE does not trigger any
spi cycles to CSE region.
* set_host_ready() - Clears reset state from host CSR.
TEST=Verified CSE recover mode on CML RVP & Hatch board
Change-Id: Id5c12b7abdb27c38af74ea6ee568b42ec74bcb3c
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
This patch helps to save additional ~19ms of booting time in
normal boot and s3 resume on CML-hatch.
BUG=b:140008206
TEST=Verified normal boot time on CML-Hatch with latest coreboot
Without this CL:
Total Time: 929ms
With this CL: (TSEG marked as WB)
Total Time: 910ms
For test marked TSEG as WP/WC:
Total Time: ~920ms
Change-Id: Ie92d2c9e50fa299db1cd8c57a6047ea3adaf1452
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35026
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit fdb9805d68.
CB:33252 wasn't reviewed by a TPM maintainer and breaks abstraction
layers (pulling TSS-details into TSPI, completely changing
interpretation of the arguments to tlcl_extend() based on TSS version).
It's also not clear why it was implemented the way it was (should have
been much easier and cleaner ways to achieve the same thing).
Since the author is not reacting, let's revert it for now. It can be
cleaned up and resubmitted later. (Not reverting the header changes
since those are not objectionable, and there are later patches dependent
on it.)
Change-Id: Ice44f55c75a0acc07794fe41c757a7bca75406eb
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
futility is built for the host. However, when cross-compiling,
the target's pkg-config is called to get the library paths which
can add paths from the cross-compilation tree instead of host.
e.g. /build/elm/usr/bin/pkg-config gets called instead of /usr/bin/pkg-config
. /build/elm/usr/bin/pkg-config adds the paths specific to the
cross-compilation target e.g. /build/elm/usr/lib instead of /usr/lib.
This causes linker to complain that files in library paths do not
match the architecture. BFD produces a warning while LLD errors out.
Fix this by passing PKG_CONFIG from host when building futility.
BUG=chromium:999217
TEST=coreboot builds
BRANCH=None
Cq-Depend: chromium:1778519
Change-Id: Id3afbf25001cf3daa72f36a290c93136cf9f162d
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35316
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ITR2 is specified twice here, which leads to the following error message
in Linux:
[ 0.263591] ACPI BIOS Error (bug): Failure creating named object
[\_SB.PCI0.LPCB.SIO0.ITR2], AE_ALREADY_EXISTS (20190509/dsfield-633)
Add comments and fix duplicated field.
As there are no users of this code yet, just rename the fields.
Tested on Supermicro X11SSH-TF.
Change-Id: I4f3307d0992fcf5ad192f412c2bd15d02572a6b0
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35294
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
me_read_config32() is defined in multiple places, move it to common
location. Also, this function is usually used for reading HFSTS
registers, hence move the HFSTS register definitions to common location.
Also add a funtion to check if the CSE device has been enabled in the
devicetree and it is visible on the bus. This API can be used by
the caller to check before initiating any HECI communication.
TEST=Verified reading HFSTS registers on CML RVP & Hatch board
Change-Id: Icdbfb6b30a007d469b5e018a313c14586addb130
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35225
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As code already used CBMEM hooks to switch from CAR to CBMEM
it was never necessary to have the structure declared inside
_car_relocatable_data.
Switch to use car_[get|set]_ptr is mostly for consistency, but
should also enable use of usbdebug with FSP1.0 romstage.
Change-Id: I636251085d84e52a71a1d5d27d795bb94a07422d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Keep track of the active timestamp table location using
a CAR_GLOBAL variable. Done this way, the entire table
can be located outside _car_relocatable_data and we only
switch the pointer to CBMEM and copy the data before
CAR gets torn down.
Fix comments about requirements of timestamp_init() usage.
Remove timestamp_cache from postcar and ramstage, as CBMEM
is available early on.
Change-Id: I87370f62db23318069b6fd56ba0d1171d619cb8a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35032
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Devices using eMCP may run at a high DRAM frequency (e.g., 3600Mbs)
while those with discrete DRAM can only run at 3200Mbps. A new option
MT8183_DRAM_EMCP is added to Kconfig for a mainboard to select,
depending on whether it supports eMCP or not.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I9b73c8b512db5104896ea0d330d56e63eb50a44b
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
.editorconfig files are widely supported and offer basic configuration
options for the project.
This sets the indention style, line-ending, character set, tells the
editor to make sure there's a newline at the end of the file and to
strip trailing whitespace.
For directories within the coreboot directory that would prefer a
different setting, additional .editorconfig files can be placed in
those directories to override any of these settings.
See the EditorConfig website for more information.
https://web.archive.org/web/https://editorconfig.org
Change-Id: Iecf1c5450edb0db533569189aa45233b91997870
Signed-off-by: Martin Roth <martin@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Id6070fb586896653a1e44951a6af8f42f93b5a7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I39f52764dc377c25953ef5dba16982a0b4637cdb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Guckian
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I77275adb7c15b242e319805b8a60b7755fa25db5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I2f350cc3008b17516b5a42cdf07e28d2da5995e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I4c9351652d81040cc4e7b85bdd1ba85709a74192
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ifd4329905847d9dd06de67b9a443c8ee50c0e7a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Setup EC_PCH_ARCORE_INT_L, tied to GPP_D17, and define as EC_SYNC_GPIO..
- change GPP_D17 definition to PAD_CFG_GPI_APIC_INVERT as
EC_PCH_ARCORE_INT_L is active low
- add EC_SYNC_GPIO to the group of chromeos_gpios for use by depthcharge
BUG=b:139384979
BRANCH=none
TEST="emerge_nocturne coreboot depthcharge chromeos-bootimage",
flash & boot nocturne in dev mode, verify that volume up and down
buttons work in the dev screen and that the device boots properly into
the kernel.
Change-Id: Ia43c622710fde8686c60b836fb8318931d79eb61
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Picasso's TimeStamp Counter is a new design and different than
Stoney Ridge. Although advertised as invariant, the ST TSC did
not become so until midway through POST making it an unreliable
source for measuring time. This is not the case for Picasso.
Remove the Stoney Ridge monotonic timer code and rely on the TSC.
Modify the calculation used in Family 15h of finding the number
of boost states first, and get the frequency directly out of the
Pstate0 register.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I909743483309279eb8c3bf68852d6082381f0dff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
These platforms return to romstage from FSP only after
already having torn CAR down. A copy of the entire CAR
region is available and discoverable via HOB.
Previously, CBMEM console detected on-the-fly that CAR
migration had happened and relocated cbmem_console_p
accoringlin with car_sync_var(). However, if the CAR_GLOBAL
pointing to another object inside CAR is a relative offset
instead, we have a more generic solution that can be used
with timestamps code as well.
Change-Id: Ica877b47e68d56189e9d998b5630019d4328a419
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35140
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Modify intel/fsp_broadwell_de such that timestamp_init() is
before raminit (and CAR teardown of FSP1.0), adding two new
early timestamps while doing so.
Other FSP1.0 platforms fsp_baytrail and fsp_rangeley already
do it this way.
Change-Id: I3b73e4a61622f789a49973a43b21e8028bcb8ca8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35279
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
From DDR4 SPD spec:
Byte 4 (0x004): SDRAM Density and Banks
Bits [7, 6]:
00 = 0 (no bank groups)
01 = 1 (2 bank groups)
10 = 2 (4 bank groups)
11 = reserved
Bit [5, 4] :
00 = 2 (4 banks)
01 = 3 (8 banks)
All others reserved
Separate DDR3 and DDR4 banks. And extened capmb, rows, cols and ranks.
Separate DDR3 and DDR4 ORGANIZATION/BUS_DEV_WIDTH offset.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I5f56975ce73d8ed2d4de7d9fd08e5ae86993e731
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Sets all unused sata ports to disable in the device tree
Note:
SATA4 and SATA5 are located at the bottom of the board, but there
is no connector for this. Apparently, a board with an increased
number of ports is very rare. Perhaps this is a separate variant
of the Asrock motherboard. For this reason, these ports are also
disabled
Change-Id: I5b3ad372f1d6607cc7b4a78e3c59d2a5ae1d2cf5
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Disable spi0, i2c0 and i2c1 in the “SerialIoDevMode” register for the
following reasons:
1. when the AMI BIOS is used, these pci devices are disabled in
lspci.log;
2. there are no pads in the inteltool.log that use the functions of
these buses
Change-Id: I01ab10eb3fd41e81a1726805247c2b472d72287c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35070
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The string "register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" was mistakenly
taken from the Intel KBL-RVP8 devicetree.cb. Remove it, since the i2c4
bus is disabled in the "SerialIoDevMode" register
Change-Id: I44ecd5c22efd66b02a2851dc14a1a95421f39a71
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
1) VR domains current limit Icc max for Sky/Kaby Lake S is set based
on the processor TDP [1]. Updates information about this
2) Sets VR voltage limit to 1.52V, as described in the datasheets [2,3]
[1] Change-Id: I303c5dc8ed03e9a98a834a2acfb400022dfc2fde
[2] page 112-119, 6th Generation Intel(R) Processor Families
for S-Platforms, Volume 1 of 2, Datasheet, August 2018.
Document Number: 332687-008EN
[3] 7th Generation Intel(R) Processor Families for S Platforms and
Intel(R) Core(TM) X-Series Processor Family Datasheet, Volume 1,
December 2018, Document Number: 335195-003
Change-Id: I6e1aefde135ffce75a5d837348595aa20aff0513
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The documentation for StackBase and StackSize in FSPM_ARCH_UPD is
confusing. Previously the region was shared for heap and stack,
starting with FSP2.1 only for heap (or 'temporary RAM') for HOBs.
Moving the allocation outside DCACHE_BSP_STACK_SIZE allows use of
stack guards and reduces amount of reserved CAR for bootblock and
verstage, as the new allocation in .bss is only taken in romstage.
BUG=b:140268415
Change-Id: I4cffcc73a89cb97ab7759dd373196ce9753a6307
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
TPMU_HA is a union of all the different hash digests, and so
sizeof(TPMU_HA) evaluates to 64 (the size of the largest one). This will
lead to out-of-bounds writes when copying smaller digests, so use the
specific digest size for each algorithm.
Change-Id: Ic9101f157d5a19836b200ecd99f060de552498d2
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 14049{49,50,51,52,53,54,55,56,57,58,60,61,62}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
This patch adds Lewisburg C62x Series PCH support by adding the
Production and Super SKUs of the following PCI devices:
- LPC or eSPI Controllers,
- PCI Express Root Ports,
- SSATA and SATA Controllers,
- SMBus,
- SPI Controller,
- ME/HECI,
- Audio,
- P2SB,
- Power Management Controller.
These changes are in accordance with the documentation:
[*] page 39, Intel(R) C620 Series Chipset Platform Controller Hub
(PCH) Datasheet, May 2019. Document Number: 336067-007US
Change-Id: I7eaf2c1bb725ffed66f86c023c415ad17fe5793d
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Add a generic SuperIO ACPI generator, dropping the need to include
additional code in DSDT for SuperIO.
It generates a device HID based on the decoded I/O range.
Tested on Supermicro X11SSH-TF using AST2400.
The SSDT contains no errors and all devices are present.
Possible TODOs:
* Add "enter config" and "exit config" bytes
* Generate support methods to enter and exit config mode
* Generate support methods to query, change or disable current
resource settings on specific LDNs
Change-Id: I2716ae0580d68e5d4fcc484cb1648a2cdc1f4ca0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Some USB 3.0 devices fail to be enumerated after USB reset, and xhci
port status register shows the device is disconnected. After measuring
the USB signal, we found that the USB disconnect threshold was lower and
that the disconnect event was triggered unexpectedly.
USB designers suggest changing discth to 15.
BUG=b:122047652
TEST=emerge-kukui coreboot chromeos-bootimage
Change-Id: I0e8556035b49d693a42cbe1099a6882a1c0ed0d1
Signed-off-by: Changqi Hu <changqi.hu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Vendor only does dummy reads right after JEDEC init is finished
and dram init was marked as finished.
Dummy reads also make much more sense after JEDEC init as a way to
send a few JEDEC commands, presumably as a way to make sure it is
ready.
TESTED on ga-g41m-es2l (still boots fine)
Change-Id: I8069f9c08ad5e5268ddbe3711d58bc42522f938c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/20979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
To support multi digists the tlcl_extend() for TPM2 expects
TPML_DIGEST_VALUE pointer as input argument.
BUG=N/A
TEST=Build binary and verified logging on Facebook FBG-1701
Change-Id: I8d86c41c23e4e93a84e0527d7cddcfd30d5d8394
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Currently SPI vendor IDs are magic numbers in spi_flash.c. These definitions
are needed for AMD's fch_spi. So add the definitions to spi_generic.h and use
it at spi_flash.c
BUG=b:136595978
TEST=Build test of several platforms that don't use stoneyridge. Build and boot
grunt (using stoneyridge new fch_spi).
Change-Id: Ie39485d8c092151db8c9d88afaf02e19c507c93f
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Martin Roth <martinroth@google.com>
Padmelon board code was written for Merlin Falcon (family 15h models 60h-6fh),
but as the needed binaries are not yet merged (commit 33615), a config
HAVE_MERLINFALCON_BINARIES was added. If the binaries are not available,
the board defaults to Prairie Falcon, which use the same binaries as Stoney
Ridge. Once the binaries are merged, the config will be eliminated. Fan
control is done through F81803A SIO, and IRQ/GPIO and other board
characteristics are the same regardless of Merlin Falcon or Prairie Falcon.
Padmelon board was created to accept Prairie Falcon, Brown Falcon and Merlin
Falcon. The requested development was for Merlin Falcon. There are some small
spec changes (such as number of memory channels) between SOCs. Brown Falcon
was not investigated, Prairie Falcon is very similar to Stoney Ridge.
Started from Gardenia code, added changes created by Marc Jones and finally
revised against schematic, which added changes to GPIO settings.
BUG=none.
TEST=Both versions tested and boot to Linux using SeaBIOS.
Change-Id: I5a366ddeb4cfebd177a8744f6edb87aecd4787dd
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The P2SB PCI device can be "hidden", which causes all sorts of
nightmares and bugs. Moreover, FSP tends to hide it, so finding
a good solution to this problem is impossible with FSP into the mix.
Since the values for IBDF and HBDF were already hardcoded as FSP
parameters, define them as macros and use these values directly to
generate the DRHD.
Change-Id: I7eb20182380b953a1842083e7a3c67919d6971b9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mimoja <coreboot@mimoja.de>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
tsc_freq_mhz() had a static table of Intel CPU families and crystal
clock, but it is possible to calculate the crystal clock speed dynamically,
and this is preferred over hardcoded table.
On SKL/KBL/CML CPUID.15h.ecx = nominal core crystal clock = 0 Hz
hence we had to use static table to calculate crystal clock.
Recommendation is to make use of CPUID.16h where crystal clock frequency
was not reported by CPUID.15h to calculate the crystal clock.
BUG=b:139798422, b:129839774
TEST=Able to build and boot KBL/CML/ICL.
Change-Id: If660a4b8d12e54b39252bce62bcc0ffcc967f5da
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35148
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Summary:
This patch calls monolake board specific function to query
settings stored in VPD binary blob to configure FSP UPD
variable HyperThreading.
Test Plan:
* Build an OCP MonoLake coreboot image, run following command
to initialize RW_VPD and insert HyperThreading key:
vpd -f build/coreboot.rom -O -i RW_VPD -s 'HyperThreading=0'
* Flash the image to MonoLake, boot and observe following
message in boot log:
Detected 16 CPU threads
If RW_VPD partition does not exist, or if HyperThreading
key/value pair does not exist, the boot log has:
Detected 32 CPU threads
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: I799d27734fe4b67cd1f40cae710151a01562b1b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Summary:
Added a framework to search VPD in romstage before memory is
avilable. vpd_cbmem.c and vpd_premem.c are added for
code specific for premem environment and for environment that
cbmem can be used.
Since global variable is forbidden in romstage. A CAR_GLOBAL
variable is defined in vpd.c. This variable holds VPD binary
blobs' base address and size from memory mapped flash.
The overall flow is:
* The CAR variable g_vpd_blob is initialized if it was not,
either at romstage (before FSP-M execution in case of FSP UPD
customization), or at ramstage.
* At ramstage, during CBMEM_INIT, the VPD binary blob contents
are copied into CBMEM.
* At vpd_find() which may be called at romstage or at ramstage,
it sets storage for a local struct vpd_blob variable.
* The variable gets contents duplicated from g_vpd_blob, if
vpd_find() is called at romstage.
* The variable gets contents obtained from CBMEM, if vpd_find()
is called at ramstage.
Added a call vpd_get_bool(). Given a key/value pair in VPD
binary blob, and name of a bool type variable, set the variable
value if there is a match.
Several checks are in place:
* The key/value length needs to be correct.
* The key name needs to match.
* THe value is either '1' or '0'.
Test Plan:
* Build an OCP MonoLake coreboot image, flash and run.
Tags:
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Iebdba59419a555147fc40391cf17cc6879d9e1b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Fastboot support in vboot_reference is unused, unmaintained, and
produces compile errors when enabled. Since there is no current
or planned use cases for fastboot, remove it.
BUG=b:124141368, chromium:995172
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I06ea816ffb910163ec2c3c456b3c09408c806d0b
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35002
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Add Kconfig to enable TXT
* Add possibility to add BIOS and SINIT ACMs
* Set default BIOS ACM alignment
* Increase FIT space if TXT is enabled
The following commits depend on the basic Kconfig infrastructure.
Intel TXT isn't supported until all following commits are merged.
Change-Id: I5f0f956d2b7ba43d4e7e0062803c6d8ba569a052
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1 [1]
registers values from the inteltool dump, is more understandable and
makes the code much cleaner. The pad configuration in this patch was
generated using the pch-pads-parser utility [2]. The inteltool dump
before and after the patch is identical (see notes)
Notes:
1. For some reason, GPIO RX State (RO) for the GPP_F4 and GPP_G10
changed the value to 0, but this doesn't affect the motherboard
operation. Perhaps this is because PAD_CFG1_GPIO_DRIVER is set to
PAD_CFG_GPI_INT(), and the pad is not actually connected. So far I
haven't circuit diagram to check this out.
2. According to the documentation [1], the value 3h for RXEVCFG is
implemented as setting 0h.
3. If the available macros from gpio_defs.h [3] can't determine the
configuration of the pad, the utility [2] generates common
_PAD_CFG_STRUCT() macros
[1] page 1429,Intel (R) 100 Series and Intel (R) C230 Series PCH
Family Platform Controller Hub (PCH), Datasheet, Vol 2 of 2,
February 2019, Document Number: 332691-003EN
[2] https://github.com/maxpoliak/pch-pads-parser/tree/stable_1.0
[3] src/soc/intel/common/block/include/intelblocks/gpio_defs.h
Change-Id: I01ad4bd29235fbe2b23abce5fbaaa7e63c87f529
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add support for the X11SSH-TF which is based on Intel KBL.
Working:
* SeaBIOS payload
* LinuxBoot payload
* IPMI of BMC
* PCIe, SATA, USB and M.2 ports
* RS232 serial
* Native graphics init
Not working:
* TianoCore doesn't work yet as the Aspeed NGI is text mode only.
* Intel SGX, due to random crashes in soc/intel/common
For more details have a look at the documentation.
Please apply those patches as well for good user experience:
Ica0c20255f661dd61edc3a7d15646b7447c4658e
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Felix Singer <felix.singer@9elements.com>
Change-Id: I2edaa4a928de3a065e517c0f20e3302b4b702323
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Platforms using postcar are with RELOCATABLE_RAMSTAGE=y. They
don't benefit from having low-memory set as writeback-cacheable.
This also fixes regression from CB:34893 that caused some random
hangs with more recent intel SoCs in ramstage.
BUG=b:140250314
Change-Id: Ia66910a6c85286f5c05823b87d48edc7e4ad9541
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Adjust CID to allow for Windows driver to attach without breaking
functionality under Linux. Same change made as to google/cyan
(which uses same Realtek RT5650 codec) in commit 607d72b.
Test: build/boot Windowns 10 on google/buddy, observe audio
drivers correctly attached to codec and Intel SST devices.
Change-Id: I839acc8427ee9b5c425885858a513e9b0b9d0f93
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This removes the need for COREBOOT_BUILD_DIR in Kconfig. Since the
original files will be replaced with the tmp file, the parent directory
already needs to be writable.
Before this change, the tmp files would be created in the CWD (src) if
COREBOOT_BUILD_DIR was not specified.
BUG=b:112267918
TEST=emerge-grunt coreboot and verified no tmp files were created in the
src directory.
Change-Id: Icdaf2ff3dd1ec98813b75ef55b96e38e1ca19ec7
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34244
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If KCONFIG_CONFIG is set to a full path, we should generate the tmp file
in the same directory instead of the current working directory.
BUG=b:112267918
TEST=emerge-grunt coreboot and verified with print statements that the
correct path was used.
Change-Id: Ia21e930a9b0a693f851c34bcde26b34886cbe902
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The Intel platforms using eSPI EC communication have just been enabling
the EC_GOOGLE_CHROMEEC_LPC option for simplicity. This does basically
the same, but at least marks it as eSPI in Kconfig for clarity.
BUG=b:140055300
TEST=Build tested only.
Change-Id: Ib56ec9d1dc204809a05c846494ff0e0d69cf70ea
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35128
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to the documentation, Sunrise PCH-H [1,2] and Lewisburg PCH
[3] supports up to 16 PCIe ports. However, ACPI contains a description
for only 12 ports. This patch adds ACPI code for missing ports
[1] page 182, Intel (R) 100 Series and Intel (R) C230 Series PCH
Family Platform Controller Hub (PCH), Datasheet, Vol 1 of 2,
December 2018, Document Number: 332690-005EN
[2] page 180, Intel (R) 200 Series and Intel (R) Z370 Series PCH
Family Platform Controller Hub (PCH), Datasheet, Vol 1 of 2,
October 2017, Document Number: 335192-003
[3] page 39, Intel(R) C620 Series Chipset Platform Controller Hub
(PCH) Datasheet, May 2019. Document Number: 336067-007US
Change-Id: I954870136e0c8e5ff5d7ff623c7a6432b829abaf
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch renames arm_tf.c and arm_tf.h to bl31.c and bl31.h,
respectively. That name is closer to the terminology used in most
functions related to Trusted Firmware, and it removes the annoying
auto-completion clash between arm64/arm_tf.c and arm64/armv8.
Change-Id: I2741e2bce9d079b1025f82ecb3bb78a02fe39ed5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Also don't define the default as this result in spurious lines in the
.config.
The only difference in config.h is on boards with the Nvidia tegra210
SOC that now select ARCH_ARM64, because its ramstage runs in that
mode. The resulting binary is identical however.
Change-Id: Iaa9cd902281e51f823717f6ea4c72e5736fefb31
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31315
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current HWID for drallion is reported as invalid by chrome, generate
new valid HWID with the following command and taking last 4 digits.
`printf "%d\n" 0x$(crc32 <(echo -n '$1'))`
BUG=b:140013681
Change-Id: I410d37fc3f3372e9420d674b65f2c9a704b670f2
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Many (if not all) platforms have moved to using consistent
boot flow constructs where a weak car_stage_entry() is no longer
necessary to avoid the complexity of handling the numerous and
different boot flow combinations. The weak symbol is just causing
issues so remove it.
Change-Id: I7e7897c0609aac8eef96a08bb789374b2403956d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35135
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The MSRs were already named as PRMRR in broadwell, just
mismatching with the rest of the code. All later devices
use the names PRMRR and UNCORE_PRMRR for these MSRs.
Reflect the name change in structures and local variables.
Change-Id: Id825ba2c083d0def641dd9bf02d3b671d85b1e35
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34825
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I'm moving the .xcompile file into the $(obj) directory so we can leave
the source pristine. We need to pass the location of .xcompile into
genbuild_h.sh.
BUG=b:112267918
TEST=Ran genbuild_h with and without an .xcompile and verified it was
passed.
Change-Id: I8b3a75b478fad92a0b09246f0a00b0580f8c4aef
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This reduces disk usage during builds by removing all object files and
other intermediate files directly after a build instead of waiting for
the entire build to pass.
Change-Id: Ic2feecd58658e8bac8c6e7a851737784e35b83ef
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35112
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This option removes everything in the build tree but coreboot.rom,
config.build, config.h and make.log - a useful subset of the tree for
further testing.
Change-Id: I27e559d8d7dc90d8fe5c4ed8e25249e202e5da36
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35136
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
During boot sequence sometime touchscreen reset keeps failing. Also, kernel
dmesg shows "dmesg:i2c_hid i2c-GDIX0000:00: failed to reset device" message.
This adds around 4 more seconds to the boot sequence. Setting the appropriate
delay of 120ms between enable and reset for Goodix Touchscreen helps to
synchronize and address this failure. This value is 120 ms as per Goodix Spec.
BUG=b:138413748
BRANCH=None
TEST=Built and tested on Hatch system
Change-Id: I15005c568f285ec7bad9a0bec4498e2fdd20782b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34626
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, we don't have UPDs to set emmc settings per mainboard on CML.
This code change is to create mmc.c to provide interface to override dll
settings per mainboard.
Notice: set_mmc_dll function will override the dll values in FSP.
BUG=b:131401116
BRANCH=none
TEST=Boot to OS and confirm the dll values have been overridden.
Change-Id: Ib3c72b9851f41585ec099d8ae83a721af87ed383
Signed-off-by: Kane Chen <kane.chen@intel.com>
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Additional changes in this patch:
- Move descriptions below the license header
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I51d5b1f01ff47ed752761116e3f32cb9e168584f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34637
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Additional changes in this patch:
- Remove comments saying that a file is based on another file from the
coreboot project.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: If61689db67c58f0d66ab96ca749bfcd589935ce2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34607
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create a new Kconfig symbol that allows an x86 device to begin execution
when its reset vector is in DRAM and not at the traditional 0xfffffff0.
The implementation will follow later, this is just to setup various
ENV_xxx definitions correctly for the build environment.
Change-Id: I098ecf8bf200550db1e15f178f7661c1ac516dc5
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This enables the use of .bss section for ENV_BOOTBLOCK
and ENV_VERSTAGE even with CAR_GLOBAL_MIGRATION=y.
In practice, boards with CAR_GLOBAL_MIGRATION=y currently
build with romcc-bootblock so they will not be using .bss.
Change-Id: Ie9dc14f3e528d3e4f48304f4d7de50df448a8af6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This allows for minor optimization as num_timestamps becomes
a constant zero for a function with local scope. The loop
with calls to timestamp_add() gets removed from bootblock.
Change-Id: Id230075c0e76fe377b6ea8c8ddf8318e07d29b91
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This provides stack guards with checking and common
entry into postcar.
The code in cpu/intel/car/romstage.c is candidate
for becoming architectural so function prototype
is moved to <arch/romstage.h>.
Change-Id: I4c5a9789e7cf3f7f49a4a33e21dac894320a9639
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34893
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ENV_ROMSTAGE_OR_BEFORE is a direct replacement for testing
defined(__PRE_RAM__) as a true statement instead of with the
help of the preprocessor.
Note that for x86, due to existence of ENV_POSTCAR and ENV_SMM,
ENV_ROMSTAGE_OR_BEFORE and ENV_RAMSTAGE are not the inverse of
each other.
Change-Id: Ibd2292f922ccb9e79d10ca9bc35797048d174287
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34939
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently only x86 requires special handling here, for simplicity
avoid introducing <arch/rules.h> and deal with this directly in
<rules.h>.
For consistency prefixes are changed from ARCH_ to ENV_.
Change-Id: I95a56dbad3482202f6cc03043589bebfb13c39af
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Board has CAR_GLOBAL_MIGRATION=n and can use .bss for a
variable that was previously declared with CAR_GLOBAL.
Test for !defined(__PRE_RAM__) can be transformed into
ENV_RAMSTAGE here as the warnings about invalid bmcinfo
structure do not need to be repeated in SMM console, which
is generally disabled anyways due to DEBUG_SMI=n.
Change-Id: I6b63213484107fa0eeb0d952d8766916b44a3c4e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Additional changes in this patch:
- Make sure files say that they're part of the coreboot project
- Move descriptions below the license header
Note that the file include/arch/acpi.h is a fantastic example of why
moving to the authors file is needed. Excluding the guard statements,
it has 8 lines of copyrights for 3 function declarations.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I334baab2b4311eb1bd9ce3f67f49a68e8b73630c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34606
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Kukui AP doesn't remember if the last AP reset was due to AP watchdog.
We need to enable CHROMEOS_USE_EC_WATCHDOG_FLAG so that it will query
the reset reason from EC.
BUG=b:109900671,b:118654976
BRANCH=none
TEST=1. run 'mosys eventlog clear; stop daisydog; echo > /dev/watchdog'
2. wait for watchdog reset
3. check 'mosys eventlog list | grep watchdog'
Change-Id: I053cc7664bbaf0d3fcae26ba9481a0ad700dca90
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Additional changes in this patch:
- Make sure files say that they're part of the coreboot project
- Move descriptions below the license header
- Fix some spacing
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Id5f26a73f0df366651c076a94975bce1fb321b70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34605
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
EFP1 is configured as 'DisplayPort with HDMI/DVI
compatibility'. Using this setting 4K monitor is configured
into lower resolution.
Change EFP1 setting to 'HDMI/DVI'
The next addtional small changes are made in VBT:
UEFI GOP Driver
Child Device 2 = LFP
Child Device 3 = EFP1/LFP
LFP Panel configuration Y-Res of Panel #10 = 1920
BUG=N/A
TEST=LCD and HDMI on Facebook FBG1701
Change-Id: Idc694b15ff94b83291a8c8252e269b7e6d96f87b
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35043
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
cb_sha.c depends on C_ENVIRONMENT_BOOTBLOCK.
Include cb_sha.c unconditional since C_ENVIRONMENT_BOOTBLOCK is default for
chipsets.
BUG=N/A
TEST=Boot Linux 4.20 and verify logging on Facebook FBG-1701
Change-Id: If93195596efe7d8f298430e67eb1cf79804b96fc
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Changes to the sandybridge memory init code (both MRC
and native) now require SPD data on all populated channels
in order for dimms to be detected properly, so copy
spd_data[0] to spd_data[2], as LINK always has 2
channels of memory down.
Test: boot google/link, observe onboard RAM correctly
detected on both channels
Change-Id: Id01d57d5e5f928dfc1cd9063ab1625c440ef2bbe
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
DRAM_SIZE_MB should be the maximum size (255GiB / -m 261120M)
that’s possible with QEMU on AArch64 virt because it tries to search
the DRAM_SIZE_MB range to find the true memory size.
Signed-off-by: Asami Doi <d0iasm.pub@gmail.com>
Change-Id: Id479c0b18d1e1adceecdcca13e36119b95617e6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Register exception handlers to avoid a Synchronous External Abort
that is raised when you try to access a non-memory address on ARMv8.
An exception handler can jump over the faulting instruction.
This is the feature only for QEMU/AArch64.
Signed-off-by: Asami Doi <d0iasm.pub@gmail.com>
Change-Id: I09a306ca307ba4027d9758c3debc2e7c844c66b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
After ChromiumOS CL:1293132 and CL:1295890, Chrome EC can store the flag
telling if the last reboot was triggered by AP watchdog for some boards
(e.g., Kukui).
This CL adds a new function google_chromeec_get_ap_watchdog_flag(),
which reads the AP watchdog flag from Chrome EC, and updates the tables
of reset causes and reset flags.
A new Kconfig option CHROMEOS_USE_EC_WATCHDOG_FLAG is added for
elog_handle_watchdog_tombstone() to determine if watchdog reset was
triggered by the AP watchdog flag from EC instead of the tombstone in
AP.
BUG=b:109900671,b:118654976
BRANCH=none
TEST=test with https://review.coreboot.org/c/coreboot/+/31843
Change-Id: I7a970666a8c6da32ac1c6af8280e808fe7fc106d
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Copy ec_commands.h directly from ChromiumOS EC repository (CL:1520574).
Since ec_commands.h already defines usb_charge_mode and only
USB_CHARGE_MODE_DISABLED is used in coreboot, enum usb_charge_mode is
removed from ec.h.
To avoid redefinition of the BIT macro, #ifndef check is added to
include/types.h.
BUG=b:109900671,b:118654976
BRANCH=none
TEST=emerge-kukui -j coreboot
Change-Id: I7ed5344fc8923e45e17c3e2a34371db6f80b079d
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31885
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When upstreamed, GPIO and RAM config for clapper variant was taken
from an older branch, leading some boards to fail to boot.
Update based on chromium branch firmware-clapper-5216.199.B,
commit 362d845 [baytrail: implement baytrail technical advisory 556192]
Change-Id: I099ee2cd0833e4b9ab093663c4549c79ec044127
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We're planning to have a use case with a custom USB device that
implements the USB mass storage protocol on its bulk endpoints, but does
not have the normal MSC class/protocol interface descriptors and does
not support class-specific control requests (Get Max LUN and Bulk-Only
Reset). We'd like to identify/enumerate the device via
usb_generic_create() in our payload but then reuse all the normal MSC
driver code. In order to make that possible, this patch factors a new
usb_msc_force_init() function out of usb_msc_init() which will
initialize an MSC device without checking its descriptors. It also adds
some "quirks" flags that allow devices registered this way to customize
behavior of the MSC stack.
Change-Id: I50392128409cb2a879954f234149a5e3b060a229
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some broken USB mass storage devices send another zero-length packet at
the end of the data part of a transfer if the amount of data was evenly
divisible by the packet size (which is pretty much always the case for
block reads). This packet will get interpreted as the CSW and screw up
the MSC state machine.
This patch works around this issue by retrying the CSW transfer when it
was received as exactly 0 bytes. This is the same mitigation the Linux
kernel uses and harmless for correctly behaving devices. Also tighten
validation of the CSW a little, making sure we verify the length before
we read any fields and checking the signature in addition to the tag.
Change-Id: I24f183f27b2c4f0142ba6c4b35b490c5798d0d21
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34485
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch changes the Rockchip SPI and I2C drivers to use the new
buffer_from_fifo32()/buffer_to_fifo32_prefix() helpers when accessing
their FIFOs (mostly just to demonstrate that/how the helpers work).
Change-Id: Ifcf37c6d56f949f620c347df05439b05c3b8d77d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Many peripheral drivers across different SoCs regularly face the same
task of piping a transfer buffer into (or reading it out of) a 32-bit
FIFO register. Sometimes it's just one register, sometimes a whole array
of registers. Sometimes you actually transfer 4 bytes per register
read/write, sometimes only 2 (or even 1). Sometimes writes need to be
prefixed with one or two command bytes which makes the actual payload
buffer "misaligned" in relation to the FIFO and requires a bunch of
tricky bit packing logic to get right. Most of the times transfer
lengths are not guaranteed to be divisible by 4, which also requires a
bunch of logic to treat the potential unaligned end of the transfer
correctly.
We have a dozen different implementations of this same pattern across
coreboot. This patch introduces a new family of helper functions that
aims to solve all these use cases once and for all (*fingers crossed*).
Change-Id: Ia71f66c1cee530afa4c77c46a838b4de646ffcfb
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The panel description may be pretty large (for example, 1.3k for BOE
TV101) due to init commands and we should only load the right config
when display is needed.
BUG=None
TEST=make -j; boots and see display on Krane.
Change-Id: I2560a11ecf7badfd0605ab189d57ec9456850f75
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
With C_ENVIRONMENT_BOOTBLOCK, CONFIG_DCACHE_BSP_STACK_SIZE needs to be
set to define a stack region that can be shared over all stages using
CAR. It makes sense to use that Kconfig option's value instead of a
hardcoded value. This will result in less false positives when the
stack size is big, for instance with FSP using the coreboot stack.
In many configurations with C_ENVIRONMENT_BOOTBLOCK the stack_base is
at the base of CAR. If the stack grows too large it operates out of
CAR, typically resulting in a hang. Therefore the stack guards are
extended to cover 256 bytes at the base to at least provide a warning
when the romstage is dangerously close of running out of stack.
Change-Id: I2ce1dda4d1f254e6c36de4d3fea26e12c34195ff
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
corebootpayload package in upstream TianoCore was replaced with
UEFIPayload, add external payload build option for UEFIPayload.
BUG=N/A
TEST=Select TianoCore payload as UEFIPayload, build and able to boot up on
QEMU q35 after PCIE_BASE set.
Change-Id: I0b7785fde9f4113b2cd91323ac0358b229c5a6e6
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34459
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To make explicit when vboot2 error codes should be returned,
use the new vb2_error_t type on all functions which return
VB2_ERROR_* constants.
Additionally, add required vboot submodule commit id e6700f4c:
2019-07-31 14:12:30 +0800 - (vboot: update vboot2 functions to use new vb2_error_t)
NOTE: This patch was merged separately on the Chromium tree:
https://chromium-review.googlesource.com/c/1728499
BUG=b:124141368, chromium:988410
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I804c2b407e496d0c8eb9833be629b7c40118415c
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:1728292
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Set the controller state to D0 during the uart init sequence, this
ensures the controller is up and active.
One more argument "const struct device *dev" has been added
to uart_lpss_init function.
BUG=b:135941367
TEST=Verify no timeouts seen during UART controller enumeration
sequence in CML, ICL and APL platforms
Change-Id: Ie91b502a38d1a40a3dea3711b015b7a5b7ede2db
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34810
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enlarge PRERAM_CBFS_CACHE region from (16K - 4) to (48K - 4) bytes to
decompress and load more data from CBFS in romstage.
BUG=b:134351649
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: Idc23a67c886718e910ca3c50468e5793f19c8d66
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34896
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since SRAM space is too small to fit all needed features, enable
VBOOT_RETURN_FROM_VERSTAGE and overlap decompressor, verstage and
romstage to gain more space.
BUG=b:134351649
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: Ibe336cf93b01fa2ea57b4c2e0a89685424878c91
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34871
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some boards (e.g., Kukui) need GPIO based CS for SPI0. This patch
changes the pinmux and binds the pins to the correponding SPIs.
When using GPIO based SPI CS, we need to manually make CS log/high
before/after SPI transactions.
BUG=b:132311067
BRANCH=none
TEST=Verified that b/132311067 is irreproducible
Change-Id: I61653fb19242b6ee6be9a45545a8b66e5c9c7cad
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The bootsplash.jpg needs to match the framebuffer resolution.
Configuration errors are more visible if they can be compared
easily.
Changed message to be always printed:
"Setting up bootsplash in ${FRAMEBUFFER_RESOLUTION}"
Added message:
"Bootsplash image resolution: ${IMAGE_RESOLUTION}"
Change-Id: Ib4a06d53c0134b99d3e9e6d3eda9fa30fca9ef7d
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34598
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previously, the initial value for secdatak was embedded
in secdata_tpm.c as a uint8_t array. Switch to using
vb2api_secdatak_create instead, and write the value in
ctx->secdatak.
Remove an unnecessary call to vb2api_secdata_create in
_factory_initialize_tpm.
BUG=b:124141368, chromium:972956
TEST=make clean && make test-abuild
BRANCH=none
TEST=Check that size and value of initial secdatak
has not changed. Apply the patch below and
check for this output:
_factory_initialize_tpm():266: _factory_initialize_tpm: secdatak sizes are identical? 1
_factory_initialize_tpm():269: _factory_initialize_tpm: secdatak values are identical? 1
diff --git a/src/security/vboot/secdata_tpm.c b/src/security/vboot/secdata_tpm.c
index ff62185107..c1818b482f 100644
--- a/src/security/vboot/secdata_tpm.c
+++ b/src/security/vboot/secdata_tpm.c
@@ -148,6 +148,18 @@ static uint32_t write_secdata(uint32_t index,
return TPM_E_CORRUPTED_STATE;
}
+/*
+ * This is derived from rollback_index.h of vboot_reference. see struct
+ * RollbackSpaceKernel for details.
+ */
+static const uint8_t secdata_kernel[] = {
+ 0x02,
+ 0x4C, 0x57, 0x52, 0x47,
+ 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00,
+ 0xE8,
+};
+
/*
* This is used to initialize the TPM space for recovery hash after defining
* it. Since there is no data available to calculate hash at the point where TPM
@@ -250,6 +262,11 @@ static uint32_t _factory_initialize_tpm(struct vb2_context *ctx)
* indication that TPM factory initialization was successfully
* completed.
*/
+ VBDEBUG("%s: secdatak sizes are identical? %d\n", __func__,
+ sizeof(secdata_kernel) == sizeof(ctx->secdatak));
+ VBDEBUG("%s: secdatak values are identical? %d\n", __func__,
+ memcmp(secdata_kernel, ctx->secdatak,
+ sizeof(secdata_kernel)) == 0);
RETURN_ON_FAILURE(set_kernel_space(ctx->secdatak));
if (CONFIG(VBOOT_HAS_REC_HASH_SPACE))
@@ -452,7 +469,7 @@ uint32_t antirollback_read_space_firmware(struct vb2_context *ctx)
/* Read the firmware space. */
rv = read_space_firmware(ctx);
- if (rv == TPM_E_BADINDEX) {
+ if (true) {
/*
* This seems the first time we've run. Initialize the TPM.
*/
Change-Id: I74261453df6cc55ef3f38d8fb922bcc604084c0a
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:1652874, chromium:1655049
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
google_chromec_get_event() depends on the main copy of EC which is
used by ACPI subsytem in the kernel for querying events.
google_chromeec_get_event() also clears the event from EC. Thus if the
kernel has to identify the wake source, it has no way to do that. Thus
instead depend on events_copy_b to log the wake source. Please look at
go/hostevent-refactor for more info.
BUG=b:133262012
BRANCH=None
TEST=Hack hatch bios and make sure hostevent log is correct.
Change-Id: I39caae2689e0c2a7bec16416978877885a9afc6c
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We need to ensure uma_memory_size and uma_memory_base stay within a
32-bit address range. Both of these variables are 64 bits wide, so it is
simplest to use 64 bit math when doing the bit shifts and then check if
they are in range after.
Change-Id: Idd180f31e8cff797a6499b12bc685daa993aae05
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1229665, 1229666
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
coreboot would clear CMOS by request via IPMI command, for example
BMC can issue "bios-util server --boot_order enable --clear_CMOS"
to set the request and reboot the system, then coreboot would clear CMOS
on the next boot.
Tested on Mono Lake
Change-Id: I21d44557896680cfac3c3b6d83e07b755b242cad
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34857
Reviewed-by: Johnny Lin
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Cometlake FSP allows provison to configure SD controller WP pin, As
some of board design might choose not to use the SD WP pin from SD
card controller. This implementation adds a config that allows to
enable/disable SD controller WP pin configuration from FSP.
BUG=b:123907904
Change-Id: Ic1736a2ec4b9370d23a8e3349603eb363e6f59b9
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34900
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
C strict aliasing rules state that it is undefined behaviour to access
any pointer using another pointer of a different type (with several small
exceptions). Eg.
uint64_t x = 3;
uint16_t y = *((uint16_t *)&x); // undefined behaviour
From an architectural point of view there is often nothing wrong with
pointer aliasing - the problem is that since it is undefined behaviour,
the compiler will often use this as a cop-out to perform unintended or
unsafe optimizations. The "safe" way to perfom the above assignment is
to cast the pointers to a uint8_t * first (which is allowed to alias
anything), and then work on a byte level:
*((uint8_t *)&y) = *((uint8_t *)&x);
*((uint8_t *)&y + 1) = *((uint8_t *)&x + 1);
Horribly ugly, but there you go. Anyway, in an attempt to follow these
strict aliasing rules, the ReadMEM() function in SB800 does the above
operation when reading a uint16_t. While perfectly fine, however, it
doesn't have to - all calls to ReadMEM() that read a uint16_t are passed
a uint16_t pointer, so there are no strict aliasing violations to worry
about (the WriteMEM() function is exactly similar). The problem is that
using this unnecessary workaround generates almost 50 false positive
warnings in Coverity. Rather than manually ignore them one-by-one, let's
just remove the workaround entirely. As a side note, this change makes
ReadMEM() and WriteMEM() now match their definitions in the SB900 code.
Change-Id: Ia7e3a1eff88b855a05b33c7dafba16ed23784e43
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Port_List is an array of 8 elements, and GCC 9 is warning that there
are no 'others' when all 8 elements are explicitly initialized, which is
causing the build to fail. Remove the 'others => Disabled' clause to
silence this.
Change-Id: Id082e7a76641438f3fb4c4d976dbd254a7053473
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34918
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
add_ivrs_device_entries() is a recursive function, and each recursive
call is passed a pointer to a root_level variable declared outside the
function. In an attempt to make the function self-contained, the initial
call is made with the root_level pointer set to NULL, and then the
function attempts to detect this and allocate a root_level variable for
the rest of the calls. This makes memory management very tricky - for
example, the pi code incorrectly attempts to free the root_level
variable at the end of *each* recursive call, which only avoids being a
double-free because free() in coreboot is currently a no-op. Let's
keep life simple and declare root_level as a local variable outside the
first function call instead.
Change-Id: Ifd63ee368fb89345b9b42ccb86cebcca64f32ac8
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1362811
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34387
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This brings in 4 new commits from the upstream repository.
65a6d94 Free image buffer on read error
9de64c7 Fix various abort(), crashes, and memory errors
7c9db58 Bump to version 1.8
3b3c3cc Use C99 uintXX_t instead of implementation-specific u_intXX_t types
Change-Id: If949309a7481537de6529c205fe745d5509906a9
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Variable length arrays were a feature added in C99 that allows the
length of an array to be determined at runtime. Eg.
int sum(size_t n) {
int arr[n];
...
}
This adds a small amount of runtime overhead, but is also very
dangerous, since it allows use of an unlimited amount of stack memory,
potentially leading to stack overflow. This is only worsened in
coreboot, which often has very little stack space to begin with. Citing
concerns like this, all instances of VLA's were recently removed from the
Linux kernel. In the immortal words of Linus Torvalds [0],
AND USING VLA'S IS ACTIVELY STUPID! It generates much more code, and
much _slower_ code (and more fragile code), than just using a fixed
key size would have done. [...] Anyway, some of these are definitely
easy to just fix, and using VLA's is actively bad not just for
security worries, but simply because VLA's are a really horribly bad
idea in general in the kernel.
This patch follows suit and zaps all VLA's in coreboot. Some of the
existing VLA's are accidental ones, and all but one can be replaced with
small fixed-size buffers. The single tricky exception is in the SPI
controller interface, which will require a rewrite of old drivers
to remove [1].
[0] https://lkml.org/lkml/2018/3/7/621
[1] https://ticket.coreboot.org/issues/217
Change-Id: I7d9d1ddadbf1cee5f695165bbe3f0effb7bd32b9
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33821
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This variable is overwritten on one branch of the next if statement, and
the other branch returns, so this assignment does nothing.
Change-Id: I63737929d47c882bbcf637182bc8bf73c19daa9f
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: scan-build 8.0.0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
DqByteMapCh0 and DqByteMapCh1 are declared adjacently in the
FSP_M_CONFIG struct, so it is tempting to begin memcpy at the address of
the first array and overwrite both of them at once. However, FSP_M_CONFIG
is not declared with the packed attribute, so this is not guaranteed to
work and is undefined behaviour to boot. It is cleaner and less tricky
to copy them independently. The same is true for DqsMapCpu2DramCh0 and
DqsMapCpu2DramCh1, so we change those as well.
Change-Id: Ic6bb2bd5773af24329575926dbc70e0211f29051
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 136538{8,9}, 140134{1,4}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33135
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
DqByteMapCh0 and DqByteMapCh1 are declared adjacently in the
FSP_M_CONFIG struct, so it is tempting to begin memcpy at the address of
the first array and overwrite both of them at once. However, FSP_M_CONFIG
is not declared with the packed attribute, so this is not guaranteed to
work and is undefined behaviour to boot. It is cleaner and less tricky
to copy them independently. The same is true for DqsMapCpu2DramCh0 and
DqsMapCpu2DramCh1, so we change those as well.
Change-Id: If394f14c4a39d6787ae31868241229646c26be7a
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1365730, 14013{38,39,40,42,43}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
For files built in ramstage and smm -classes, testing
for !__PRE_RAM__ is redundant.
All chip_operations are exluded with use of DEVTREE_EARLY
in static devicetree, so garbage collection will take care
of the !__SMM__ cases.
Change-Id: Id7219848d6f5c41c4a9724a72204fa5ef9458e43
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In addition to zero IccMax specified by mainboard with socketed CPU, allow
a zero LoadLine default.
The SoC code will fill in the default AC/DC LoadLine values are per
datasheets:
* "7th Generation Intel® Processor Families for H Platforms, Vol 1"
Document Number: 335190-003
* "7th Generation Intel® Processor Families for S Platforms and
Intel ®Core™ X-Series Processor Family, Vol 1"
Document Number: 335195-003
The AC/DC LoadLine is CPU and board specific.
TODO: Find out how to get the LoadLine from vendor firmware and find out
how to map those to different CPU LoadLines.
Change-Id: I849845ced094697e8700470b4af95ad0afb98e3e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34938
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Datasheets used:
* "7th Generation Intel® Processor Families for H Platforms, Vol 1"
Document Number: 335190-003
* "7th Generation Intel® Processor Families for S Platforms and
Intel ®Core™ X-Series Processor Family, Vol 1"
Document Number: 335195-003
This allows mainboards to specify a zero IccMax, which all mainboards with
socketed CPU should do.
Change-Id: I303c5dc8ed03e9a98a834a2acfb400022dfc2fde
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34937
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Level trigger is recommended setting for touchscreen interrupt of
kohaku, so we would change it as the recommedation.
BUG=b:139179200
BRANCH=none
TEST=Verified touchscreen works on kohaku
Change-Id: Ibbcdbe3ab555d014048f66ff527e539c5b566187
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
region_is_subregion() checks whether the size of the inner region is
larger than the size of the outer region... which isn't really necessary
because we're already checking the starts and ends of both regions.
Maybe this was added to ensure the inner region doesn't overflow? But
it's not guaranteed to catch that in all cases. Replace it with a proper
overflow check.
Change-Id: I9e442053584a479a323c1fa1c0591934ff83eb10
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The original name DCACHE_BSP_STACK_SIZE will be exclusively
used to define the fixed size of BSP stack when it is located
near the beginning of CAR region. This implementation has the
stack located at the very end of CAR region.
Remove other fam10-15 exclusive configs from global space.
Change-Id: I8b92891be2ed62944a9eddde39ed20a12f4875c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This change ports some previous work for Skylake:
cb58683ef5 soc/intel/skylake: Add support for mode-aware DPTF
...to common DPTF code so that we can support mode-aware DPTF for other
Intel platforms.
BUG=b:138702459
BRANCH=none
TEST=Manually test on hatch:
(1)Add DPTF_TSR0_TABLET_PASSIVE and DPTF_TSR1_TABLET_PASSIVE
to hatch baseboard dptf.asl
(2)Flash custom EC FW code which updates DPTF profile number when
entering/exiting tablet mode
(3)On DUT, see /sys/class/thermal/thermal_zone2/trip_point_{1,2}_temp
updated when device mode is switched (tablet/clamshell)
Signed-off-by: Philip Chen <philipchen@google.com>
Change-Id: I5e7b97d23b8567c96a7d60f7a434e98dd9c69544
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34785
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some timeouts given were too small when serial console is enabled due to
its spinlock making code runtime worse with every AP present.
In addition we usually don't know how long specific code runs and how
long ago it was sent to the APs.
Remove the timeout argument from mp_run_on_all_cpus and instead wait up
to 1 second, to prevent possible crashing of secondary APs still
processing the old job.
Tested on Supermicro X11SSH-TF.
Change-Id: I456be647b159f7a2ea7d94986a24424e56dcc8c4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
There was no code present to call wrmsr with the data we
prepared in the structs. The MSRS are already set up by FSP,
just reference with the more recent names of PRMRR and UNCORE_PRMRR.
Change-Id: Ib49e7af52e1170a1304975ff0ae63f99e106dffe
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
As most platforms will share the subset of enabling
both low RAM WB and high ROM WP MTRRs, provide them
with a single function.
Add possibility for the platform to skip these if
required.
Change-Id: Id1f8b7682035e654231f6133a42909a36e3e15a1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34809
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
At the moment we only have two splitting of TSEG,
one with and one without IED. They can all use
same implementation.
Make configuration problems of TSEG region assertion
failures.
Rename file from stage_cache.c to tseg_region.c to
reflect it's purpose.
Change-Id: I9daf0dec8fbaaa1f4e6004ea034869f43412d7d5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34776
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: David Guckian
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The src/lib/edid now supports reporting manufacturer name so we should
define that in MIPI panels and print out in initialization.
BUG=None
TEST=emerge-kukui coreboot; boots properly
Change-Id: If844da84ecca31307127b14c66bbe17c408699f3
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
When debugging usually we want to print out a full identifier for panel,
that should be manufacturer and part number. Previously the edid only
contains ascii_string (which is usually the part number) but we should
export manufacturer name as well.
Change-Id: I0020fdd5b9f9331b25825876e0de4dc7e26b0464
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The fixed size of init command in lcm_init_table is wasting lots of
space and we should change to packed array since the command buffer
already provides length information.
With this change, BOE panel init commands have been reduced from 4848
bytes to 1309 bytes.
BUG=b:80501386,b:117254947
TEST=emerge-kukui coreboot chromeos-bootimage; Boots properly
Change-Id: I359dde8e6f2e1c0983f4677193bb47a7ae497ca6
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34778
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some Kukui variants may have eDP panels connected via a PS8640 MIPI bridge
which we may retrieve EDID dynamically.
BUG=b🅱️137517228
TEST=emerge-jacuzzi coreboot chromeos-bootimage; boots and see display.
Change-Id: I85aac5255e6a3e6019299670486214ecffbf9801
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34516
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Many devices in Kukui family will be using MIPI panels, which needs
hard-coded EDID and initialization commands. And because each device may
have its own layout and ID, there should be very few devices sharing
same panel configuration. As a result, we want to put panel data (EDID
and init commands) into board-specific modules, provided by
`get_panel_description` function.
The panel numeric ID is identified by ADC 2, and is currently available
as higher 4 bits of sku_id(). After ID is retrieved, the
get_panel_description should return a reference to the EDID and table of
init commands. The default implementation is to simply return NULL, and
the data for real devices should be provided by panel_*.c in further commits.
BUG=b:80501386,b:117254947
BRANCH=none
TEST=boot correctly on Kukui
Change-Id: I19213aee1ac0f69f42e73be9e5ab72394f412a01
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The MT8183 display serial interface (DSI) is based on MIPI
Alliance Specification, supporting high-speed serial data
transfer between host processor and peripheral devices such
as display modules.
DSI supports both video mode and command mode data transfer
defined in MIPI spec, and it also provides bidirectional
transmission with low-power mode to receive messages from
the peripheral.
Reference: MT8183 Application Processor Functional Spec,
6.7 Display Serial Interface (DSI)
BUG=b:80501386,b:117254947
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Ic413f524ca0b36f0b01f723a71fe9745e2710cd2
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
For systems with real MIPI panels (8173/oak was using PS8640 eDP
bridge), we have to send DCS commands to initialize panel.
BUG=b:80501386,b:117254947
TEST=make -j # board = oak and boots
Change-Id: Ie7c824873465ac82a95bcb0ed67b8b9866987008
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34773
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The video timing should be based on PHY timing. Some values can be
ignored on 8173 because of fixed values in PHY but should be calculated
for newer platforms like 8183.
BUG=b:80501386,b:117254947
TEST=make -j # board = oak and boots
Change-Id: Id3ad2edc08787414a74188f5050460e98222caf4
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The PHY timing should be calculated by data rate (Mbps). However for
8173 some values were hard-coded so we want to introduce a new
mtk_phy_timing structure and a weak function mtk_dsi_override_phy_timing
that allows per-SOC customization to apply PHY timings.
BUG=b:80501386,b:117254947
TEST=make -j # board = oak and boots
Change-Id: I1176ca06dda026029ff431aca7f9e21479eed670
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add code to read SPD data, parse it and save into SMBIOS table. This is
implemented for socketed DDR4 chips only. For soldered-down memory this
is not implemented and probably won't be ever needed.
TEST=tested on OCP Monolake mainboard, and found dmidecode -t memory to
work. The stack has also been tested on an out-of-tree board.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I1162eb4484dab46f1ab9fe3426eecc4d9378e8e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34681
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Add ability to decode basic fields of DDR4 SPDs and produce SMBIOS table
17. XMP, schemas, extended field parising is totally not yet implemented.
Also, put CRC function used in DDR2, DDR3 and DDR4 ina common file.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: If3befbc55cf37e1018baa432cb2f03743b929211
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
IMC is found on certain Xeon processors. On such platforms SPDs are not
connected to SMBus on PCH but to dedicated IMC-owned pins. The purpose
of this driver is to expose access to the i2c/smbus controller associated
with IMC.
Datasheet used: Intel Xeon Processor D-1500 Product Family, Volume 2,
reference 332051-001
This driver is largely based on i2c-imc.c Linux driver.
https://lwn.net/Articles/685475/
TEST=single/double reads and single writes on Xeon-D1500.
Hardware: Open Compute Project Monolake platform.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: Idbcda1c2273b9a5721fcd9470b4de182192779e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34678
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to use internal UART it needs to 'enabled'. This is normally done
by FSP. However sometimes internal UART is needed before FSP is invoked.
TEST=check if printk() show up in early romstage. Tested on OCP Monolake.
Tested on out-of-tree mainboard to see if UART on LPC still works.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I88a7b1a38abf9a09137f6dd75a5a9dee104daaca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34683
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds support for allowing devices to provide a
"compatible" property string that can be used when _HID is set to
PRP00001. This is used to allow Linux kernel drivers to match the
device to appropriate driver based on the OF-style compatible
string.
Reference:
https://www.kernel.org/doc/Documentation/acpi/enumeration.txt
BUG=b:129162037
TEST=Verified that atmel touchscreen gets enumerated correctly on
kohaku using PRP0001 and compatible string.
Change-Id: I8a306854c67ab2f056ea8774df46599ef0c55761
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
This change updates the Atmel touchscreen ACPI node to use PRP0001 as
_HID to allow OF-style compatible string matching for enumeration.
Reason for this change: Atmel touchscreen driver in Linux kernel looks
for "compatible" property to decide if it is okay to attach to the
device. This check seems to be a protection against old firmware in
the field that do not have the right properties.
BUG=b:129162037
TEST=Verified that touchscreen works on Kohaku.
Change-Id: I6d027f8533494e903efd1da8da1fa273a97fe9b2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
The only platform-specific difference in mtk_dsi_phy_clk_setting is how
to configure MIPI TX because those registers (and logic) are quite
different across different SOCs.
The calculation of data rate is actually the same so we should isolate
it and move to common, and rename mtk_dsi_phy_clk_setting to a better
name as mtk_dsi_configure_mipi_tx.
BUG=b:80501386,b:117254947
TEST=make -j # board = oak and boots
Change-Id: I894dc2c4c053267debf5a58313b2bb489bcf5f3a
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The 'bpp' was referred to both 'bits per pixel' and 'bytes per pixel' in
MTK DSI driver and should be corrected. By this change we now always
consider 'bpp' as 'bits per pixel', and rename the variables for other
cases.
BUG=b:80501386,b:117254947
TEST=make -j # board = oak and boots
Change-Id: Ibd405220b73859e5592c68f498af07eef8d7edbc
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34770
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The DSI initialization is almost the same for 8173 and 8183, so we want
to move most of common functions into common/dsi.c.
The major board-specific functions left are:
- reset (controller register has different format)
- pin_drv_ctrl (8183 does not need this)
BUG=b:80501386,b:117254947
TEST=make -j # board=oak (mt8173)
Change-Id: I8d4369a3c84db551287a9c9d1b22f552c5f7518d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34769
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It is easier to track CAR_GLOBAL_MIGRATION which is
the approach to be deprecated with the next release.
This change enforces new policy; POSTCAR_STAGE=y is
not allowed together with CAR_GLOBAL_MIGRATION=y.
Change-Id: I0dbad6a14e68bf566ac0f151dc8ea259e5ae2250
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Build error on missing vb2ex_printf() in bootblock stage
Add the file vboot_logic.c which contains the missing vb2ex_printf().
BUG=N/A
TEST=Boot Linux 4.20 and verify logging on Facebook FBG-1701
Change-Id: I3f649f3faf1e812d592e4981bc75698e2cad1cc8
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
The Kohaku V24 schematic adds two additional temperature sensors
to the EC. Add these to the DPTF tables.
Cq-Depend: chromium:1742914
BRANCH=none
BUG=b:138578073
TEST=Rebuild EC and BIOS, look for new thermal sensors in kernel.
1. Build EC
``cd ~/trunk/src/platform/ec``
``make -j BOARD=kohaku``
2. Program EC
``./util/flash_ec --board=kohaku``
3. Reboot device
4. Rebuild BIOS
``cd ~/trunk/src/third_party/coreboot``
``FEATURES="noclean" FW_NAME=kohaku emerge-hatch chromeos-ec depthcharge
vboot_reference libpayload coreboot-private-files intel-cmlfsp
coreboot-private-files-hatch coreboot chromeos-bootimage``
5. Use flashrom to program the BIOS
6. Reboot device
7. Log into the root console (ctrl-alt-F2 or servo)
8. Example thermal sensor information
``grep . /sys/class/thermal/t*/type``
Look for "TSR0" through "TSR3" in the output.
Change-Id: Ib8f38beae6392855927ce1249c229d7a114c72b2
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34765
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Oops, I missed this in the last CL.
The pin needs to be configured as owned by GPIO, so that the kernel
driver can bind it with an IRQ.
BUG=b:139165490
TEST=Ensure kernel nastygram about inability to claim the IRQ is gone
Change-Id: I26c08d75d8b4e3b834db6e90868239899605fa5b
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In general, third party code (such as vboot) doesn't know what the
underlying types are for the integers in <stdint.h>, so these macros are
useful for portably printing them. Of these definitions, coreboot so far
has only used PRIu64 (in one place), which isn't needed anymore since we
know what the underlying type of a u64 is.
Change-Id: I9e3a300f9b1c38e4831b030ff8af3fed2fa60f14
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Change the stoneyridge definitions into picasso. The named 0 and 1
buses are controlled by the PSP and not directly accessible by host
firmware. I2C4 operates only in slave mode so is not added to to
the bus clear-after-reset sequence.
The I2C controller is fundamentally the same as on Stoney Ridge so
the ability to clear a potentially jammed bus is still required.
Program Picasso's new pad control registers in the MISC AcpiMmio
space according to the recommended settings.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Ibbc5504ebc36654e28c79fe3ae17cc0d9255118f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This is a consolidation of the respective feature in `soc/intel/*lake/`,
including additional support for MAINBOARD_POWER_STATE_PREVIOUS.
For the latter, firmware has to keep track of the `previous` state. The
feature was already advertised in Kconfig long ago, but not implemented.
SoC code has to call pmc_set_power_failure_state() at least once during
boot and needs to implement pmc_soc_set_afterg3_en() for the actual
register write.
Change-Id: Ic6970a79d9b95373c2855f4c92232d2aa05963bb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The MT8183 SOC has a DISP (display controller) that supports
overlay, read/write DMA, ... etc. The output of DISP goes to
display interface DSI, DPI or DBI directly.
Reference: MT8183 Application Processor Functional Spec,
6.1 Display Controller
BUG=b:80501386,b:117254947
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Ic4aecc58d081f14f5d136b9ff8e813e6f40f78eb
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The 'dual DSI mode' was never used by any real boards running coreboot
and is introducing lots of complexity when it comes to refactoring.
In order to create a common display stack for MTK SOCs, we want to first
drop dual DSI mode so 8173 and 8183 DSI/DDP implementation will be more
similar to each other.
BUG=b:80501386,b:117254947
TEST=emerge-oak coreboot
Change-Id: I357c30cc687803ca8045d0b055dec2e22eef4291
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34693
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PMC logic shuts down the PCH thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold (LTT) in case of Dynamic Thermal Shutdown
when S0ix is enabled.
BUG=None
BRANCH=None
TEST=Verified Thermal Device (B0: D20: F2) TSPM offset 0x1c [LTT (8:0)]
value is 0xFE on Sarien.
Change-Id: Ibc336be0523ff4e65a818474907faf20fc417ff4
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
PMC logic shuts down the PCH thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold (LTT) in case of Dynamic Thermal shutdown
when S0ix is enabled.
BUG=None
BRANCH=None
TEST=Verified Thermal Device(B0: D18: F0) TSPM offset 0x1c [LTT (8:0)]
value is 0xFE on Arcada.
Change-Id: I1915b974b10638b0f6ab97c6fb9b7a58d2cabc59
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Recent Coverity scan indicated potential NULL deference; if either
spi->dma_in or spi->dma_out are NULL, the fifo_error() check could
dereference a NULL pointer.
Also fixed what appears to be a logic bug for the spi->dma_out case,
where it was using the todo (count) from spi->dma_in.
Found-by: Coverity CID 1241838, 1241854
Change-Id: Icd1412f0956c0a4a75266d1873d5e9848aceee32
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34787
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The common code adheres to the Intel requirement of bringing up the
cores with INIT SIPI SIPI. This sequence is tolerated on some AMD
AMD CPUs but fails on others. Add a way to skip the second SIPI.
TEST=Mock up on grunt and verify no errors
BUG=b:138919564
Change-Id: I201869003ddc7d04d332cd5734ac6d63979d89e0
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34759
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There was the potential for misuse of the override early GPIO table,
because if the override early GPIO table did not have a corresponding
entry in the base table, it would not get overridden, and there was
no way to know except manual inspection (this has already happened
here), so now all hatch mainboards are required to explicitly list out
all of their required early GPIOs.
TEST=booted several hatch boards, verified that they can communicate
with TPM and successfully train memory
Change-Id: I0552b08a284fd6fb41a09fef431a0d006b0cf0bd
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Currently SPI bus id is used to map to the controller in order to set
the controller state. In certain platforms SPI bus id might not be
exactly the same as GSPI bus id. For example, in Intel platforms SPI bus
id 0 maps to fast spi i.e. SPI going to the flash and SPI bus id 1 .. n
map to GSPI bus id 0 .. n-1. Hence using SPI bus id leads to mapping to the
GSPI controller that is not enabled. Use the GSPI id bus so that the right
controller is set to active state. This fixes the regression introduced
by CB:34449
BUG=b:135941367
TEST=Boot to ChromeOS.
Change-Id: I792ab1fa6529f5317218896ad05321f8f17cedcd
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Add explicit CBMEM_STAGE_CACHE option. Rename
CACHE_RELOCATED_RAMSTAGE_OUTSIDE_CBMEM to TSEG_STAGE_CACHE.
Platforms with SMM_TSEG=y always need to implement
stage_cache_external_region(). It is allowed to return with a
region of size 0 to effectively disable the cache.
There are no provisions in Kconfig to degrade from
TSEG_STAGE_CACHE to CBMEM_STAGE_CACHE.
As a security measure CBMEM_STAGE_CACHE default is changed to
disabled. AGESA platforms without TSEG will experience slower
S3 resume speed unless they explicitly select the option.
Change-Id: Ibbdc701ea85b5a3208ca4e98c428b05b6d4e5340
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds the following improvements:
* Easier to read.
* Checks to see if .xcompile is complete.
* Checks the make return code. This will catch if .xcompile is missing.
BUG=b:112267918
TEST=Modified my .xcompile and ran abuild and verified that
missing_arches got set correctly. Also deleted .xcompile and verified
there was a failure.
Change-Id: I7604d431f398fc0c80a857a0c7c21e164004cc99
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
To avoid confusion use VENDORCODE_ELTAN_VBOOT and
VENDORCODE_ELTAN_MBOOT config values.
Include verfied_boot and mboot subdirectories as CPPFLAGS when
measured boot or verified boot is enabled. This allows to generate
binary with measured boot enabled only.
BUG=N/A
TEST=Boot Linux 4.20 and verify logging on Facebook FBG-1701
Change-Id: Iaaf3c8cacbc8d2be7387264ca9c973e583871f0a
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33442
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The BMC on Supermicro X11SSH takes 34 seconds to start the IPMI KCS, but
the default timeout of the IPMI KCS code is just 100 msec.
Add a configurable timeout option to wait for the BMC to become ready.
As it only should boot very long after power on reset, it's not a
problem on reset or warm boot.
Tested on Supermicro X11SSH.
The IPMI driver doesn't fail with a time-out any more.
Change-Id: I22c6885eae6fd7c778ac37b18f95b8775e9064e3
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Updating from commit id dac763c7:
2019-05-10 10:43:55 -0700 - (Make vboot -Wtype-limits compliant)
to commit id 9c906110:
2019-08-06 06:07:01 +0000 - (vboot/tpm: fix return type inconsistencies)
This brings in 68 new commits.
Change-Id: Ia96347d8ed94db6f0ec5f5108cb98ab0c4087bd4
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Sometimes the display native orientation does not match the device
default orientation, so allow rotation of the framebuffer before
it is displayed on screen.
set_pixel now take coordinates in the rotated coordinate system,
and converts the coordinates before writing to the framebuffer.
Also, screen.size now matches the rotated system (_not_ the
framebuffer size).
BUG=b:132049716
TEST=Boot krane, see that FW screen is orientation properly.
Change-Id: If9316c0ce33c17057372ef5995a2c68de4f11f02
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Sometimes the display native orientation does not match the device
default orientation. We add a parameter to be passed to libpayload,
which can then do the rotation.
BUG=b:132049716
TEST=Boot krane, see that FW screen is orientation properly.
Change-Id: I5e1d94b973a3f615b73eebe0ca1202ba03731844
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This CL adds a new board, QEMU/AArch64, for ARMv8. The machine supported
is virt which is a QEMU 2.8 ARM virtual machine. The default CPU of
qemu-system-aarch64 is Cortex-a15, so you need to specify a 64-bit cpu
via a flag.
To execute:
$ qemu-system-aarch64 -M virt,secure=on,virtualization=on \
-cpu cortex-a53 -bios build/coreboot.rom -m 8192M -nographic
Change-Id: Id7c0831b1ecf08785b4ec8139d809bad9b3e1eec
Signed-off-by: Asami Doi <d0iasm.pub@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The pinctrl driver in the linux kernel automatically turns off SCI
routing for all GPIOs exported via ACPI, so this patch sets up
dual-routing of the EMR_GARAGE_DET signal so that one can be used
for IRQs and one for the SCI wake.
Change-Id: Iadeb4502c5a98a72ba651bdcad626609656c196f
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34780
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The touchscreen controller was never added to the device tree, and the
next board rev will have this IC connected. Set it up in the device tree
with conservative power resource timings from the datasheet.
BUG=b:138869702
BRANCH=none
TEST=compiles; current board rev does not have touch IC
Change-Id: I759fb32f31c8eee0e6bd664c6a82308354ef5d08
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enabling stylus pen device and pen_eject event.
- Adding enable_gpio for power sequencing
- Configuring GPP_H4 and GPP_H5 as native function
- Adding PENH device node for pen ejection event
BUG=b:137326841
BRANCH=none
TEST=Verified pen input operation and pen_eject event (pop-up and wake
from s0ix on pen ejection)
Change-Id: Ic252a1f90c0fc6cb9b1e426d75a8b503824681f3
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34581
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
FSP1.0 has low memory corruptions below CONFIG_RAMTOP
on S3 resume path, as romstage ram stack will be utilised
before there is a chance to make the necessary backup
to CBMEM.
Previously done for intel/minnowmax in commit b6fc727.
Change-Id: I2e128079b180f9978e8519b190648d516aaee0dc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34673
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Let garbage-collection take care of stage_cache_external_region()
if it is no needed and move implementation to a suitable file already
building for needed stages.
Remove aliasing CONFIG_RESERVED_SMM_SIZE as RESERVED_SMM_SIZE and
(unused) aliasing of CONFIG_IED_REGION_SIZE as IED_SIZE.
Change-Id: Idf00ba3180d8c3bc974dd3c5ca5f98a6c08bf34d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34672
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for Intel PTT. For supporting Intel PTT we need to disable
read and write access to the TPM NVRAM during the bootblock. TPM NVRAM
will only be available once the DRAM is initialized. To circumvent this,
we mock secdata if HAVE_INTEL_PTT is set. The underlying problem is,
that the iTPM only supports a stripped down instruction set while the
Intel ME is not fully booted up. Details can be found in Intel document
number 571993 - Paragraph 2.10.
Change-Id: I08c9a839f53f96506be5fb68f7c1ed5bf6692505
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Drallion is a new mainboard using Intel Comet Lake SOC. As a starting
point, I took mainboard/sarien as the reference code and modified WHL
to Comet Lake.
BUG=b:138098572
Test=compiles
Signed-off-by: Thejaswani Putta <thejaswani.putta@intel.com>
Change-Id: I541952a4ef337e7277a85f02d25979f12ec075c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34497
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add an API to check if device is a LPSS controller. This API can be
used for IRQ assignments for LPSS PCI controllers, since the LPSS
controllers have a requirement of unique IRQ assignments and do not
share same IRQ# with other LPSS controllers.
SOC code is reponsible to provide list of the LPSS controllers
supported and needs to implement soc_lpss_controllers_list API,
in case it needs to use this common implementation.
Change-Id: I3f5bb268fc581280bb1b87b6b175a0299a24a44a
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34137
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update libgfxinit:
o Add support for ULX (CPU Y series) variants
o Add support for Kaby/Coffee/Whiskey/Amber Lakes
o Publish Read_EDID() procedure
o Fix certain GMBUS error conditions
o Fix DP training when clock recovery needed voltage-swing increase
o Fix scaling on eDP for BDW+
Change-Id: Ib252303708d2bb0524ecc47f498df45902ba774f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
This implementation revises the UART PCI device reference in common
UART driver. The SOC functions have been aligned to provide the UART
PCI device reference using pcidev_path_on_root.
The uart_get_device() return type is changed, and files in which
it gets used are updated.
Change-Id: Ie0fe5991f3b0b9c596c3de9472e98e4091d7dd87
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Commit 509f469 [drivers/fsp1_1/raminit.c: Always check FSP HOBs]
inadvertently made use of the mrc_hob conditional on
CONFIG_DISPLAY_HOBS, when there is no relation between the two,
leading to MRC cache data being corrupted. On some devices this
caused RAM training to be redone, on others it resulted in a
bricked device.
Fix this by removing the condition on CONFIG_DISPLAY_HOBS.
Test: boot google/{cyan,edgar}, observe third boot and onward do not
brick device, properly use mrc_hob via cbmem console and timestamps.
Change-Id: I01f6d1d6dfd10297b30de638301c5e0b6545da9c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34685
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Let garbage-collection take care of stage_cache_external_region()
when it is not needed and move implementation to a suitable file
already building for needed stages.
Change-Id: Ic32adcc62c7ee21bf38e2e4e5ece00524871b091
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Let garbage-collection take care of stage_cache_external_region()
when it is not needed and move implementation to a suitable file
already building for needed stages.
Change-Id: Ia6adcc0c8bf6d4abc095ac669aaae876b33ed0f3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34669
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Let garbage-collection take care of stage_cache_external_region()
if it is no needed and move implementation to a suitable file already
building for needed stages.
Remove aliasing CONFIG_RESERVED_SMM_SIZE as RESERVED_SMM_SIZE.
Change-Id: Ie6fcc40fba14575e8ee058f45a1a359a05f00aca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
smbios.h had already declared smbios_mainboard_enclosure_type so this
change defines it. It can be overridden in a mainboard so the enclosure
type can be set at runtime.
We have a mainboard that will be used in different enclosures and we are
planning on using a single BIOS image for all of the enclosures so it
will need to be set dynamically based on sku.
BUG=b:138745917
TEST=Built arcada firmware and verified via dmidecode that enclosure type
is correctly set to "Convertible", then temporarily added a
smbios_mainboard_enclosure_type to arcadas board file returning
0x20 and verified with dmidecode that the enclosure type is
"Detachable"
Change-Id: Iba6e582640989f5cb7e6613813e7b033760a977c
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Call OpenSBI in M-Mode and use it to set up SBI and to lockdown the
platform. It will also jump to the specified payload when done.
This behaviour is similar to BL31 on aarch31.
The payload is 41KiB in size on qemu.
Tested on qemu-riscv:
Required to boot a kernel as OpenSBI's instruction emulation feature
is required on that virtual machine.
Tested on SiFive/unleashed:
The earlycon is working. No console after regular serial driver
should take over, which might be related to kernel config.
Change-Id: I2a178595bd2aa2e1f114cbc69e8eadd46955b54d
Signed-off-by: Xiang Wang <merle@hardenedlinux.org>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
The abuild script will `cd` into the build directory. FAILED_BOARDS
defaults to a relative path, so it ends up trying to echo into a
directory that doesn't exist.
If we set the realpath to the file then we can correctly update the
failed/passed boards file.
BUG=none
TEST=make what-jenkins-does and verified there was a failed_boards and
passed_boards in coreboot-builds.
Change-Id: Ib3af003b090668380a9425583a9f4367023820a6
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
BRANCH=none
BUG=b:138152075
TEST=Build for cometlake board with the PmTimerDisabled policy in
devicetree set to 1.
With PmTimerDisabled = 0
>> iotools mmio_read8 0xfe0018fc
0x00
With PmTimerDisabled = 1
>> iotools mmio_read8 0xfe0018fc
0x02
Bit 1: ACPI Timer Disable (ACPI_TIM_DIS): This bit determines
whether the ACPI Timer is enabled to run.
- 0: ACPI Timer is enabled
- 1: ACPI Timer is disabled
Change-Id: I83f49505a804c99d7978e5d541ea9fe8ead9b88f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Caller needs to take into account that bus numbers may
have not been assigned yet. Same issue existed before
with early ramstage and mostly does not cause problems
when used with static devices on bus 0.
Change-Id: I4865b4277dbc858c8c2ffd2052defcaa1a92173c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34614
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Constify the struct device arguments in below APIs:
> acpi_device_name
> acpi_device_path_fill
> acpi_device_path
> acpi_write_dbg2_pci_uart
> acpi_device_scope
> acpi_device_path_join
The APIs do not seem to modify the argument and are using
device argument as reference to device only.
Change-Id: Ic2ce045f17efa288eb41503795723d0ad5ec78bd
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34625
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This function can capture and allocate its own eye data, so in that case
set need_free to true so it is freed at the end.
Change-Id: I63ca6d743e6610d3e3ab6bd7b0356aabdfa6f784
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1393969
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Accessing the higher vidtcon variables using pointer arithmetic from the
lower address FIMD_CTRL struct is undefined behaviour, since pointers
manipulations are not allowed outside the objects they point to. The
standard-blessed way is to perform the arithmetic using integer
addresses first, and then convert that to a pointer. The end result is
the same, but avoids the risk of unsafe optimizations from an
over-zealous compiler.
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1402096, 1402124, 1402131, 1402169
Change-Id: I13ed23836e8e9076ae0bfd88c05c4f2badac9c49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Clear the GPI Interrupt Status & Enable registers to prevent any
interrupt storms due to GPI.
BUG=b:138282962
TEST=Ensure that the Interrupt status & enable registers are reset
during the boot-up when the system is brought out of G3, S5 & S3. Ensure
that the system boots fine to ChromeOS.
Change-Id: I2185355d0095601e0778b6bf47ae137cc53e4051
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Moving these to bootblock as we are seeing some instances where
devices are rebooting into the recovery broken screen with the 0x5a error (no
bootable storage device in system). This needed to be done for KBL
platforms and never got transferred to hatch.
Please reference https://review.coreboot.org/c/coreboot/+/23647
BUG=b:137681648
BRANCH=None
TEST=Run autotest faft_bios and faft_ec suites
Change-Id: I8cf09c26d77d890f5d0490709504e9edf485a93f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34484
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ...
- adds the PCH ID for C232 chipset,
- renames "Premium" chipset to "HM170" (because of same IDs),
- reorders the Skylake-H PCH IDs ascending by hex values.
Used documents:
- Intel 332690-005EN
Change-Id: I859975fe7bcd3c10dead8fe150a2fbead9c64a51
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Stoney Ridge is family 15h models 70h-7Fh, Merlin Falcon is family 15h models
60h-6Fh. Add changes based on config parameter SOC_AMD_MERLINFALCON to make
the code backward compatible with Merlin Falcon.
BUG=none.
TEST=Tested later with padmelon board.
Change-Id: I00fe832324500bcb07fca292a0a55f7258a2d82f
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33624
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PMC logic shuts down the PCH thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold (LTT) in case of Dynamic Thermal Shutdown
when S0ix is enabled.
BUG=133345634
BRANCH=None
TEST=Verified Thermal Device (B0: D20: F2) TSPM offset 0x1c [LTT (8:0)]
value is 0xFE on Hatch.
Change-Id: Ib20fae04080b28c6105e5a187cc5d7a55b48d709
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33147
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PMC logic shuts down the PCH thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold (LTT) in case of Dynamic Thermal shutdown
when S0ix is enabled.
BUG=None
BRANCH=None
TEST=Verified Thermal Device (B0: D18: F0) TSPM offset 0x1c [LTT (8:0)]
value is 0xFE.
Change-Id: Ibd1e669fcbfe8dc6e6e5556aa5b1373ed19c3685
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33129
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There were two hooks in the boot state machine which dumped the ME
status to the debug UART, which is unnecessary. Removed the hook
for the BS_OS_RESUME_CHECK state, leaving just BS_PAYLOAD_LOAD, which
is called before FspNotifyEndOfFirmware, as required.
BUG=b:138463532
BRANCH=none
TEST=Boot up, check cbmem to ensure the ME status messages are
only printed one time.
Change-Id: I86bc6e33de4096f33023730ffabb25715c985de0
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
As discussed on the mailing list and voted upon, the coreboot project
is going to move the majority of copyrights out of the headers and into
an AUTHORS file. This will happen a bit at a time, as we'll be unifying
license headers at the same time.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Id3382d19088cba2703350339b0bd0cfb3c0e63b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34604
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The amdht code currently relies on an idiosyncratic ASSERT() macro,
which actually doesn't do anything right now, and even it did would only
print a janky error message. Replace this with the normal ASSERT() macro
from <assert.h>. The default behaviour now is to print an error message
but do nothing else, and failed assertions will only halt if you enable
FATAL_ASSERT, in which case, well, you asked for it.
Change-Id: I6db7565171a345f9afbc9fb37cff8fda58f942df
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1402076
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
There will be a possible out of bounds array access if
power_limit_1_time == ARRAY_SIZE(power_limit_time_sec_to_msr), so
prevent that in the index check. This issue was fixed for other cpus in
commit 5cfef13f8d (cpu/intel: Fix out-of-bounds read due to off-by-one
in condition). Based on the discussion for that commit, also remove the
magic constant 28 in favour of the index of the last array element.
Change-Id: Ic3f8735b23a368f8a9395757bd52c2c40088afa1
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1229673
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The bdk_phys_to_ptr() function converts a uint64_t address to a void *
pointer. Judging by the comments, the old implementation had a check
that would refuse to convert a null pointer, which required several
workarounds when trying to convert the address 0 to a pointer. This
isn't the case for coreboot though, which implements this function
as a simple (void *) cast, so we can remove the old workarounds.
Change-Id: I6537d1699e6726c1fb155d69a51e14da856232de
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1393962
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The total number of errors is only needed after a final tuning run at the
end of this function, so we can remove this unneeded store for earlier
runs.
Change-Id: I62adb38ccba98d90bcf8ccd13998762b9b694111
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1393967
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The virt machine is special as it doesn't emulate flash and it puts
the coreboot.rom at start of DRAM. The payload loader doesn't know
about CBFS in DRAM and overwrites the CBFS while decompressing
payloads, resulting in undefined behaviour.
Mark the region as SRAM to make sure the payload won't
overwrite the CBFS while decompressing.
As payload is always decompressed to DRAM, it wouldn't touch
SRAM memory regions.
Change-Id: I36a18cb727f660ac9e77df413026627ea160c1e1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Fix regression introduced in bd4bcab
"lib: Rewrite qemu-armv7 ramdetect".
The detected DRAM size is in MiB, thus needs to adjusted accordingly
before passed to ram_resource.
Wasn't seen earlier as everything works, except payload loading.
Change-Id: I4931372f530e7b4e453a01e5595d15d95a544803
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
This reverts commit 598af2e2c2.
Reason for revert: This commit breaks every board with VBOOT enabled
if the platform is apollolake, broadwell, skylake, baswell, baytrails
or icelake. The reason is, that the SoC selects
VBOOT_MUST_REQUEST_DISPLAY by default, and this has a dependency now
on VBOOT_MAY_SKIP_DISPLAY_INIT. This will only be auto-selected if
it is a CHROMEOS platform.
Change-Id: I3872d9aa993326ded135d8a5d950d5b1b1eddf34
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34308
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Print an error message and return if an invalid QUP or BLSP is
encountered. This prevents a possible null pointer dereference
of spi_clk.
Change-Id: I374e15ce899c651df9c2d3e0f1ec646e33d4bdb2
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1401086
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Consider the following assignment:
u64 = s32
For positive values this is fine, but if the s32 is negative, it will be
sign-extended in the conversion to a very large unsigned integer. This
manifests itself in two ways in the following code:
First, gpu_pipe{a,b}_port_select are defined as int, and can have the
values 1 or 2. In the case when they have the value 2, the shift 2 << 30
will be a negative number, making it susceptible to the sign-extension
problem above. Change these variables to something more reasonable like
a uint8_t, which is unsigned.
Second, in any bit shift, any variable with width less than an int will
be implicitly promoted to an int before performing the bit shift.
For example, the variable gpu_pipea_power_on_delay is a uint16_t, and if its
highest bit is set, the shift gpu_pipea_power_on_delay << 16 will become
negative, again introducing the above problem. To prevent this, cast all
smaller variables to a u32 before the shift, which will prevent the
implicit promotions and sign extensions.
Change-Id: Ic5db6001504cefb501dee199590a0e961a15771b
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1229699, 1229700, 1229701, 1229702
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34487
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
volt_str is used to print information about the RAM configuration
in report_common_dimm(), so let's print out "unknown voltage" if the
voltage isn't recognized rather than a garbage value.
Change-Id: I8e85917fd682e166172fbf10597bde4a8a11dfc7
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1393958, 1393982
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Change the fletcher32 checksum calculation to match PSP and AGESA
implementations.
The symptom of the failure has only been noted in Picasso's BIOS
Directory Table, when a BIOS binary image of different sizes were
passed to amdfwtool. The PSP halts the boot process with the bad
BDT checksum, and if allowed to continue, AGESA asserts later due
to a failed BDT verification.
This version has been verified to produce the same result as found
at https://en.wikipedia.org/wiki/Fletcher%27s_checksum.
TEST=Build apu2, bettong, grunt and verify before/after amdfw.rom
is unchanged.
Change-Id: I2ba2c49a70aa81c15acaab0be6b4c95e7891234f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
* Move armv7 RAM dection to a common place
* Enable it for all emulated platforms
* Use 32bit probe values and restore memory even on failure
* Use the new logic on the following boards:
** qemu-armv7
** qemu-riscv
Tested on qemu-system-riscv:
Fixes kernel panic due to wrong memory limits reported.
Change-Id: I37386c6a95bfc3b7b25aeae32c6e14cff9913513
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add VBT 8.0.1038 binary.
Panel #10 is modified to support the 1200x1920 LCD panel.
This panel is configured as default.
LCD and HDMI are working fine.
BUG=N/A
TEST=booting Facebook FBG1701
Change-Id: If327e4e071df61b02fcec45213c2b700320ef269
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Use latest OpenSBI that include support for dynamic firmware loader.
That allows us to use OpenSBI similar to BL31 on aarch64:
* coreboot loads the payload
* coreboot loads OpenSBI ELF right before payload handoff
* OpenSBI does platform lockdown and provides runtime services
* OpenSBI hands control to already loaded payload
The uncompressed compiled OpenSBI code is about 41KiB.
Required to boot GNU/Linux on qemu-riscv as some instructions needs to be
emulated by SBI.
Change-Id: If7ed706bc54a75fb583a8aa46fdd61ae7d18c546
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Also don't define the default as this result in spurious lines in the
.config.
This also cleans up an unused Kconfig file.
In the generated config.h CPU_QEMU_POWER8 is gone as expected and
ARCH_RAMSTAGE_PPC64 moves a few lines, but the value stays the same.
Change-Id: I70b64e49e1ce07b8f30d9bbc493272bdfb3bb0bf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We are treating reg_val like a bit mask, so use bitwise or instead of
boolean or, and use |= to enable certain bits instead of overwriting the
whole variable.
Change-Id: Ia8c0ea5a58e25b3b58ed82caba20f8e49a30fb68
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1287070
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Based on updated schematics, change polarity of USI_INT, and add
the reset and enable GPIOs to the touchscreen ACPI node. The stop
GPIO can't be used with the current implementation of _ON, as the
way it's wired will cause power sequencing to fail.
BUG=b:137133194, b:138240502
BRANCH=none
TEST=Compiles, don't have next board rev to test with
Change-Id: I1dfb8e649418e4c5e9b897fb4bc11393adc21ea2
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
So far the bootsplash is only correctly rendered if the framebuffer is
set up as 1024x768@16.
Different resolutions did not show anything, differnent depth resulted
in the distorted images.
This commit removes this limit by using the actual framebuffer resolutions
and combines the code for x86 and yabel.
For the moment the bootsplash is still limited to VGA-OptionROM
framebuffer init.
It was tested in 1280x1024@32 on the wip razer blade stealth using the
intel vgabios.
Change-Id: I5ab7b8a0f28badaa16e25dbe807158870d06e26a
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34537
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Prevent implicit cast to pointers.
The compiler doesn't warn about the conversion from
integer to pointer without a cast, because SA_DEV_ROOT
is literally '0' and there seems to be an exception
for that conversion.
Change-Id: I64fc156e3b9f578414ad03a00edb7cf3e33205c1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The bus variable doesn't live outside the scope of this function, and is
only used as a convenient way for passing the pointers to all the
sub-functions, so it doesn't need to be allocated. Put it on the stack
instead.
Change-Id: I4370d77445952731d20f7d9a91803612f4d21aef
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1294801
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The "internal PME" wake-up source could be from integrated LAN,
HD audio/audio DSP, SATA, XHCI, CNVi, or an ME maskable host wake.
chromium:1680839 adds USB port details to the wake-up when the
XHCI causes the wake-up. Expand the logging for wake-up details to
identify and log the other wake-up sources with more details. Note that
wake on Integrated LAN (GbE), SATA, and ME Maskable Host Wake are not
in use on Hatch, so these will not be tested.
BUG=b:128936450
BRANCH=none
TEST=``FW_NAME=hatch emerge-hatch chromeos-ec depthcharge vboot_reference
libpayload coreboot-private-files intel-cmlfsp coreboot-private-files-hatch
coreboot chromeos-bootimage``
Ensure /build/hatch/firmware/image-hatch.serial.bin has been built.
Program image-hatch.serial.bin into the DUT using flashrom.
Switch the DUT to the console (Ctrl-Alt-F2, or use the AP console via
servo).
XHCI USB 2.0
* Plug a USB keyboard into a USB-A port
* ``powerd_dbus_suspend``
* Verify low power mode by issuing the ``powerinfo`` command on the EC
console (via servo). Expect to see ``power state 4 = S0ix``.
* Press a key on the USB keyboard
* ``mosys eventlog list`` shows:
12 | 2019-06-26 14:52:23 | S0ix Enter
13 | 2019-06-26 14:53:07 | S0ix Exit
14 | 2019-06-26 14:53:07 | Wake Source | PME - XHCI (USB 2.0 port) | 3
15 | 2019-06-26 14:53:07 | Wake Source | GPE # | 109
CNVi (connected to Wi-Fi):
* Enable wake on disconnect via ``iw phy0 wowlan enable disconnect``
* Set up a hotspot on an Android phone
* Connect the Chromebook to th hotspot
* ``powerd_dbus_suspend``
* Verify low power mode by issuing the ``powerinfo`` command on the EC
console (via servo). Expect to see ``power state 4 = S0ix``.
* Turn off the hotspot on the phone
* ``mosys eventlog list`` shows:
8 | 2019-07-11 10:58:17 | S0ix Enter
9 | 2019-07-11 10:59:17 | S0ix Exit
10 | 2019-07-11 10:59:17 | Wake Source | PME - WIFI | 0
11 | 2019-07-11 10:59:17 | Wake Source | GPE # | 109
XHCI USB 3.0
* TBD
HD Audio
* TBD
Change-Id: I2c71f6a56b4e1658a7427f67fa78af773b97ec7f
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34289
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The perennial problem with u16 << 16 strikes again - the u16 is
implicitly promoted to an int before the shift, which will then become
negative if the highest bit of the u16 was set. Normally this isn't much
of a problem, but in this case tegra_dsi_writel() expects a 64 bit integer
for that argument, and so it will be sign-extended to a very large
unsigned integer if it is negative. Cast bytes to a u32 beforehand to
prevent the implicit promotion and thus this problem.
Change-Id: Iaf0fb1040ccafafde0093e9bb192c802b86cb2ac
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1294800
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34529
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This multiplication is of the form u64 = u32 * u32. Despite being stored
in a 64 bit variable, the intermediate value is still calculated using
32 bit math, which could possibly overflow. Cast one of the variables to
a u64 to ensure it uses 64 bit math instead to avoid this.
Change-Id: Ib08624812e933fdca5a51150ab36d3be49383326
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1375443
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch creates new kconfig option to bring display over external
PCI based GFX card. This kconfig to select required kconfig which are
not default selected by VGA_ROM_RUN to launch legacy oprom from pci
based GFX card.
Change-Id: I8ebde69e38defbe3321eb5e5bbd632c209ae2cd8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Set the controller state to D0 during the uart init sequence, this
ensures the controller is up and active.
One more argument struct device *dev has been added
to uart_lpss_init function for the same.
BUG=b:135941367
TEST=Verify no timeouts seen during UART controller enumeration
sequence in CML and ICL platforms.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I0187267670e1dea3e1d5e83d0b29967724d6063e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34447
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch provides an increased timeout (60ms -> 1s) for SPI
HW-sequencing flash erase operations. Without that the erase for MRC
cache writing on siemens/mc_bdx1 sometimes goes wrong because the
timeout stops waiting for flash cycle completion. It was found
during continuous integration. Investigation showed that the used flash
type takes sporadic (e.g. 5% of the test cycles) more time for completion
of erasing operation if the ambient temperature increases. The measured
time values are in range of data sheet of SPI flash. 60ms is a typical
value. So increasing the value is necessary.
tested on siemens/bdx1; measured time values with increased ambient
temperature of flash were always smaller than worst case value of 1s.
Change-Id: Id50636f9ed834ffd7810946798b300e58b2c14d2
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch moves SPI_FLASH time-outs from spi/spi_flash_internal.h for
SPI SW-sequencing to include/spi-generic.h to provide also for
SPI HW-sequencing.
tested on siemens/bdx1 and checked if all includes of
spi_flash_internal.h on other places provide an include of
spi-generic.h before
Change-Id: I837f1a027b836996bc42389bdf7dbab7f0e9db09
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The documented return value for strlcat is horribly wrong, as is the
return value itself. It should not return the number of appended bytes,
but rather the length of the concatenated string. From the man page:
The strlcpy() and strlcat() functions return the total length of the
string they tried to create. For strlcpy() that means the length of
src. For strlcat() that means the initial length of dst plus the
length of src. While this may seem somewhat confusing, it was done
to make truncation detection simple.
This change is more likely to fix existing code than break it, since
anyone who uses the return value of strlcat will almost certainly rely
on the standard behaviour rather than investigate coreboot's source code
to see that we have a quirky version.
Change-Id: I4421305af85bce88d12d6fdc2eea6807ccdcf449
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
SRCCLKENA holds 26M clock, which will fail suspend/resume,
and the SRCCLKENA is not used by mt8183,
so we can simply release it for suspend/resume to work.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui, suspend test pass.
Change-Id: Ib6e11faeb6936a1dd6bbe8b1a8b612446bf51082
Signed-off-by: Yanjie.jiang <yanjie.jiang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32666
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SSPM is "Secure System Power Manager" that provides power control in
secure domain. The initialization flow is to load SSPM firmware to
its SRAM space and then enable.
BUG=b:80501386
BRANCH=none
Test=Build pass
Change-Id: I4ae6034454326f5115cd3948819adc448b67fb1c
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31516
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The 'Jacuzzi' is a different base board that will share most of Kukui
design. For AP firmware, there will be only a few changes expected,
mostly in display (for MIPI bridge) and EC/keyboard so we want to create
it as variants inside Kukui folder, not forking a new directory.
BUG=b:137517228
TEST=make menuconfig; select 'krane' and build; select 'jacuzzi' and build.
Change-Id: Ic2b04e01628dc3db40f79f9bbdd5cc77d9466753
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34344
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It is proper to check cpu turbo mode capability after it is selected
to be enabled. If processor exhibits the presence of hardware support for
turbo, turbo global state will be updated with TURBO_ENABLE. Otherwise,
TURBO_UNAVAILABLE is applied to turbo global state.
TEST=Validated turbo state on GLK and WHL devices.
Change-Id: Ib1bc37fb339b4a0bb6a7cdc6cd4391575b22b55a
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34145
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In the case there is no the circuit diagram for motherboard, the
PCH/SoC GPIOs config is based on information from the inteltool
dump. However, available macros from gpio_defs.h can't define the
pad configuration from this dump:
0x0440: 0x0000002084000500 GPP_A8 CLKRUN#
0x0448: 0x0000102184000600 GPP_A9 CLKOUT_LPC0
0x0450: 0x0000102284000600 GPP_A10 CLKOUT_LPC1
To convert these raw DW0/DW1 register values to macros, the following
parameters must be set:
func - pad function,
pull - termination,
rst - pad reset config,
trig - rx level/edge configuration,
bufdis - rx/tx (in/output) buffer disable.
The patch resolves the above problem by adding a new macro for the
native function configuration:
PAD_CFG_NF_BUF_TRIG(pad, pull, rst, func, bufdis, trig)
These changes were tested on Asrock H110M-DVS motherboard [2].
It also resolves the problem of automatically creating pads
configuration [3,4]
[1] page 1429,Intel (R) 100 Series and Intel (R) C230 Series PCH
Family Platform Controller Hub (PCH), Datasheet, Vol 2 of 2,
February 2019, Document Number: 332691-003EN
https://www.intel.com/content/dam/www/public/us/en/documents/
datasheets/100-series-chipset-datasheet-vol-2.pdf
[2] https://review.coreboot.org/c/coreboot/+/33565
[3] https://github.com/maxpoliak/pch-pads-parser/issues/1
[4] https://github.com/maxpoliak/pch-pads-parser/commit/215d303
Change-Id: If9fe50ff9a680633db6228564345200c0e1ee3ea
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34337
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We would like to wake eve up in suspend from an MKBP event. This commit
simply enables MKBP events to wake the system in suspend using the
existing host event interface. There is an accompanying series of
patches in the EC firmware for eve that will allow a MKBP wake mask to
be configured.
BUG=chromium:786721
BRANCH=firmware-eve-9584.B
TEST=Build and flash eve, generate MKBP events on the EC and verify
that the system wakes up in suspend.
Change-Id: I75b05c83a4204d55df11589299a7488d04bbd073
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34454
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Bit 18 of MSR_POWER_CTL is documented as reserved, but we're setting it on
Haswell in order to enable EPB. It seems to work on SKL/KBL as well, so
do it there too.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Change-Id: I83da1a57a04dac206cc67f2c256d0c102965abc2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The decision to leave the alignment in stoneyridge was driven because
of a spec difference with picasso. AMD has checked the design
materials and has confirmed there was no change.
TEST=Build Grunt successfully
BUG=b:130343127
Change-Id: If3a1d5a41dc175c9733fd09ad28627962646daf9
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The EC ID of the ECDT needs to be null-terminated (see ACPI specification,
section 5.2.15), which currently isn't being done due to an off-by-one
error. strncpy() is bug-prone exactly because of issues like this, so just
skip it entirely and use memcpy() instead.
Change-Id: I0b62e1f32177c9768fa978053ab26bca93d7248d
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1402104
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Disable unused USB devices in the device tree so that the concerned ACPI
objects do not get exported to the OS.
BUG=b:133513961
BRANCH=octopus
TEST=Boot to ChromeOS. Ensure that the USB devices are disabled based
on port status and the concerned ACPI objects are not exported.
Change-Id: I0faccdfb8a9df9ec52130437433b15973e3d6f1a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add devicetree configuration for USB devices so that USB Port
Capabilities (_UPC) and Physical Location of Device (_PLD) ACPI objects
can be exported to the OS.
BUG=b:133513961
BRANCH=octopus
TEST=Boot to ChromeOS. Ensure that the _UPC & _PLD ACPI objects are
exported for the configured USB devices in the SSDT table.
Change-Id: I832ffe305d256296b7447035c5e5dcafb7c296d9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add API to disable USB devices that are not present but are configured
in the device tree either after probing the concerned port status or as
explicitly configured by the variants.
BUG=None
BRANCH=octopus
TEST=Boot to ChromeOS.
Change-Id: Ied12faabee1b8c096f2b27de89ab42ee8be5d94d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33377
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It feels appropriate to define SoC specific XHCI USB info in SoC
specific XHCI source file and an API to get that information instead of
defining it in elog source file. This will help in other situations
where the information is required.
BUG=None
BRANCH=None
TEST=Boot to ChromeOS.
Change-Id: Ie63a29a7096bfcaab87baaae947b786ab2345ed1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34290
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch lists all supported vesa mode by oprom
using Function 0x4F00 (return vbe controller information).
This information might be useful for user to select correct vesa
mode for oprom.
TEST=Enabling external pcie based graphics card on ICLRVP
Case 1: with unsupported vesa mode 0x118
Now coreboot will show below msg to user to know there is a potential
issue with choosen vesa mode and better users know the failure rather
going to depthcharge and debug further.
Calling Option ROM...
... Option ROM returned.
VBE: Getting information about VESA mode 4118
VBE: Function call invalid with unsupported video mode 0x118!
User to select mode from below list -
Supported Video Mode list for OpRom are:
0x110
0x111
0x113
0x114
0x116
0x117
0x119
0x11a
0x165
0x166
0x121
0x122
0x123
0x124
0x145
0x146
0x175
0x176
0x1d2
0x1d4
Error: In vbe_get_mode_info function
Case 2: with supported vesa mode 0x116
Calling Option ROM...
... Option ROM returned.
VBE: Getting information about VESA mode 4116
VBE: resolution: 1024x768@16
VBE: framebuffer: a0000000
VBE: Setting VESA mode 4116
VGA Option ROM was run
Change-Id: I02cba44374bc50ec3ec2819c97b6f5027c58387f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34284
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When generating entries in SSDT for DesignWare I2C controllers, only
use the speed selected in the devicetree, instead of trying all of them.
This quiets a message which looks like a bug ("dw_i2c: bad counts"),
later on in this driver when checking rise/fall times.
BUG=b:137298661
BRANCH=none
TEST=Boot and verify that I2C controllers still function, and
the nastygram message is gone.
Change-Id: I07207ec95652e8af1a42bfe31214f61a183a134e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34385
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We would like to wake nocturne up in suspend from an MKBP event. On
Nocturne, MKBP events are notified to the host via a GPIO from the EC,
EC_INT_L. However, the AP cannot wake from suspend from this GPIO.
Therefore, we'll use the host event interface to wake the system
instead.
This commit simply enables MKBP events to wake the system in suspend.
BUG=chromium:786721
BRANCH=firmware-nocturne-10984.B
TEST=Build and flash nocturne, generate MKBP events on the EC and verify
that the system wakes up in suspend.
Change-Id: I6aff4d38051c939257533229fd0085e42c01d02f
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
The processor P_BLK doesn't support throttling. This behaviour could be
emulated with SMM, but instead just update the FADT to indicate no support
for legacy I/O based throttling using P_CNT.
We have _PTC defined in SSDT, which should be used in favour of P_CNT by
ACPI aware OS, so this change has no effect on modern OS.
Drop all occurences of p_cnt_throttling_supported and update autoport
to not generate it any more.
Change-Id: Iaf82518d5114d6de7cef01dca2d3087eea8ff927
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This bit shift attempts to set bits 8 and 9 of the byte variable (counting
from 0). However, as the name suggests, this variable is only 8 bits
wide, so the shift does nothing. Reading section 7.5 of the
AMD SB800-Series Southbridges Register Programming Requirements manual,
bits 8 and 9 are already set by default, so we can remove the bit shift.
(Alternatively, we could try setting the corresponding bits one byte
higher in 0xF1 if needed.)
Change-Id: I645236441e02925ee01339378d213cb343027363
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1229582
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
- Use log2() when rounding down size_mb to the closest power of 2.
Do a sanity check beforehand that size_mb is nonzero, else log2()
will return -1 and there will be an undefined integer shift.
- The framebuffer size needs to be between 8 and 512 MiB, so check
after all the calculations are done to make sure this is the case.
Change-Id: I3962e5cdc094c8da22d8dbadf16637e02fa98689
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1391086
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Implicit fall throughs are a perpetual source of bugs and Coverity Scan
issues, so let's squash them once and for all. GCC can flag implicit fall
throughs using the -Wimplicit-fallthrough warning, and this should
ensure no more enter the code base. However, many fall throughs are
intentional, and we can use the following comment style to have GCC
suppress the warning.
switch (x) {
case 1:
y += 1;
/* fall through */
case 2:
y += 2;
/* fall through - but this time with an explanation */
default:
y += 3;
}
This patch adds comments for all remaining intentional fall throughs,
and tweaks some existing fall through comments to fit the syntax that
GCC expects.
Change-Id: I1d75637a434a955a58d166ad203e49620d7395ed
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This switch was likely copy-pasted from the one right above it. However,
the MEM_CLOCK_800MHz case isn't needed, since that is explicitly checked
and avoided before the while loop. With that gone, only the
667MHz/default case is left, which we don't need to switch over anymore.
Change-Id: Idfb9cc27dd8718f627d15ba92a9c74c51c2c1c2d
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1347372
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add function tlcl_getcapability() to return TPM2 capability.
To support TPM2 capability TPM_CAP_PCRS handling is added to
unmarshal_get_capability().
BUG=N/A
TEST=Build binary and verified logging on Facebook FBG-1701
Change-Id: I85e1bd2822aa6e7fd95ff2b9faa25cf183e6de37
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch configures GPIO pin GPP_G7 as NF1 with internal pull down.
As per schematics SD host controller SD_WP pin is not connected to
uSD card connector. Configured gpio pin as NF1 with internal pull down
in order to overcome gpio default state in hatch which makes SoC
SD_WP pin is enable.
BUG=b:137729527
BRANCH=None
TEST=Able to write/read data to/from sd card after mounting card device.
Change-Id: I0187267670e1dea3e1d5e83d0b29967714d6065e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34396
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The BBST() method writes an updated status flag mask that is intended
to be stored back in the battery object. This value needs to be
passed as a reference to an object to prevent it from being evaluated
at the time the method is loaded or it will not actually update the
BSTP value in the battery device.
This was tested by instrumenting the _BST method in the primary
battery and ensuring the value can be updated by the BBST method.
Change-Id: Ia8e207a2990059a60d96d8e0f3ed3c16a55c50f4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Add changes needed to build a project using Merlin Falcon SOC using 00670F00
vendor code, which is backward compatible with Merlin Falcon. Only the AGESA
binary image is different then the one used by 00670F00.
BUG=none.
TEST=Tested later with padmelon board.
Change-Id: Id3341f6a1ef2561a6391d3db8c54f6bdd09b0c0e
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Existing coreboot oprom implementation relies on user selected
vesa mode through CONFIG_FRAMEBUFFER_VESA_MODE Kconfig option
and expects that all oprom might support user selected vesa mode.
Take an example:
Enabling AMD external radeon PCIE graphics card on ICLRVP with
default vesa mode 0x118. Unable to get valid X and Y resolution
after executing vbe_get_mode_info() with 0x4118, return data
buffer shows 0x0 resolution. It causes further hang while trying
to draw bmpblk image at depthcharge.
This patch checks for output register AH in all vbe function
(0x3 and 0x4f00/1/2) and die() if returns error.
Change-Id: Iacd2ce468e038a14424f029df3a0adec3e5fa15c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change provides an implementation of variant_memory_sku() for
helios that overrides memory ID 3 and 4 to 0 and 1 to workaround the
incorrect memory straps in hardware for board id 0 and unknown.
BUG=b:133455595
Change-Id: I38fab1f91decac5d0a146e5a6c74e88f677af305
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
This change adds support for variant_memory_sku() that allows variant
to return memory SKU ID. Current implementation of memory_sku() is
renamed to weak implementation of variant_memory_sku(). Functionally
this change should be the same as before for all hatch variants. This
function will be overriden by helios in a follow-up CL.
BUG=b:133455595
Change-Id: I509c263ec08e0060c12ef1ea9fed673f1e3f3a41
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Correct all GPIOs with reference to the Apollo Lake SoC EDS Vol 4
revision 2.4 chapter 10.1.2.3 List of Pins that are GPIOs but cannot be
used in Function 0 (GPIO) mode.
In additional, set an internal pull to any GPI that does not have an
external resistor so that the input is not in an undefined state.
Change-Id: Ia8fe457eddbed0f4ee6bff9ef9dd7a92545be40b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
The limitation for SD-Card was originally only made for mc_apl2
mainboard. Since other mc_apl mainboards also use the SD-Card interface,
the speed mode setting is made in the parent mainboard_final.
In additional, all UHS-I bus speed modes are disabled because of a
limitation for industry use cases. This means that only HS mode is
permitted.
Change-Id: I2f1b51f13a53c2507c52d6a169d6384b8570b3bc
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch makes VGPIO_3 GPIO PIN output and low independent of
cnvi is connected or not.
BUG=b:123062346
BRANCH=None
TEST=boot up Hatch device and make sure VGPIO_3 gpio pin is driven low.
Change-Id: I629b99676f56747de1b244724709e14069250097
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34376
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Taken from
"Intel 6 Series Chipset and Intel C200 Series Chipset"
Document Number: 324645-006 and
"Intel 5 Series Chipset and Intel 3400 Series Chipset"
Document Number: 322169-004 and
"Intel 6 Series Chipset"
Document Number: 324645-001.
UPDCR was found in GNU/Linux's drivers/pci/quirks.c.
DMC2 was guessed as it's close to DMC and defined for 5 series chipset.
Test:
Run BUILD_TIMELESS=1 and compared the coreboot.roms, no differences.
Change-Id: I4fed7c38078cabd4308424c7547416e87c9e6fa7
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This CL allows that everyone can use main() in lib/bootblock.c
even if you select CONFIG_BOOTBLOCK_CUSTOM. I also rename main
functions used in some soc/ to avoid the collision with the
main function defined at lib/bootblock.c.
Change-Id: I0575c9d1ce9dea9facfcc86760dff4deee9c1e29
Signed-off-by: Asami Doi <d0iasm.pub@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34250
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GCFC (Graphics Clock Frequency Control) read is not used at
the line below.
As the default value is zero, let's remove unused read.
Found-by: scan-build 7.0.1-8
Change-Id: I82c567e3a5b0c0c4a8596ea0cb7693667c71b720
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The code currently checks that 4 <= dev_index <= 10, which after
subtraction by 4 can index into an array of length at most 7. This is
fine for the largest cpl array (which does have length 7), but is
too large for some of the others, which are smaller. This adds bounds
checks for each array access to ensure they are all within bounds.
Change-Id: I1610d35ca6cbb6cfb42c251e75b0e8b22b64252b
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1229676
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The speed argument should be one of the six values from the mem_clock
enum, so something is very wrong if this is not the case. Better to
die now than return 0, which will cause a division-by-zero error
later on where this function is called. The first two speeds are also
unsupported and have the same problem with returning 0, so die on those
as well.
Change-Id: Ib628c0eed3d6571bdde1df27ae213ca0691ec256
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1391088
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33409
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If the decoded SPD DRAM frequency is slower than the controller minimum,
then there will be an unsigned integer underflow in the following loop,
which will lead to a very large out of bounds array access. Ensure this
does not happen.
Change-Id: Ic8ed1293adfe0866781bd638323977abd110777e
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1229675
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Judging from the state machine on page 281 of the Rockchip RK3288
Technical Reference Manual (Rev 1.0 - Jun 2015), the fall through
from the INIT_MEM -> CONF states is intentional, since that is the
only way to get to the ACCESS state. Add a comment to explain this.
Change-Id: I1d0cfea07211c54d6a906f5a7481c2c760f8ef0d
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1291959
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
- Add CPU, MCH & IGD IDs for new Coffeelake SKUs
- Add PCH, LPC, SPI IDs for CNP-H PCH CM246 & C246
- Make some minor alignments & naming corrections to align with the rest
TEST= build, boot to both Linux & windows OS on CFL H & S platforms
and verified all the device Id's in serial console logs.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I343b11ea8d9c33eb189d7478511a473b145f4ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Boon Tiong Teo <boon.tiong.teo@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Currently, bluetooth FW is not loaded after a reboot. In order to do
this, we have to disable the bluetooth disable gpio (GPP_C14) in
bootblock and re-enable it in ramstage.
BUG=b:137307516
BRANCH=None
TEST=boot up Hatch device and make sure (in dmesg) that proper
bluetooth FW in loaded
Change-Id: Ic5e447d9de57790f7a100e9e03f36b047c19d8f9
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34354
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIOs related to power sequnce are
GPIO_67 - EN_PP3300
GPIO_117 - FULL_CARD_POWER_ON_OFF
GPIO_161 - PLT_RST_LTE_L
1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161
2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67
3. Power reset:
- keep GPIO_67 and GPIO_117 high and
- pull down GPIO_161 for 30ms then release it.
BUG=b:137033609
BRANCH=octopus
TEST=build image and verify on the DUT with LTE DB.
Change-Id: I7bf6fee087c885c22363b44aa98aa61f91be90b4
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
There are two hard things in computer science: cache invalidation,
naming things, and off-by-one errors. -- Anonymous
var_num records the number of initialized entries in the reg_var array.
However, this means the index of the last initialized element is one
less than the value of var_num, so we need to take that into account
when indexing into the array. This has already been fixed in several
other places (eg. sb/amd/pi/hudson/lpc.c), so let's also do so here.
Change-Id: Ibefabaca42866a3f2b22eff979c73badf86ac317
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: scan-build 8.0.0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
512 bytes is much too big for this buffer, which only needs to hold a
path that will have a length of at most 20. The large buffer size also
triggers a -Wformat-truncation warning with GCC since it is later
printed into the smaller temp_string array, so shrink it down to
something reasonable.
Change-Id: I6a136d1a739c782b368d5035db9bc25cf5b9599b
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The FSP_CAR option has additional configuration options whose default
values result in boot failures. Since default values should always boot,
default to the open-source CAR NEM Enhanced implementation instead. This
also allows us to get rid of an unnecessary vendor-specific special case.
Change-Id: I30b1808f91701c07dce6f1de08c213150e8a675a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34287
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For AMD's Family17h processors, verstage needs to be run in the PSP,
before memory is initialized. This adds that binary into the PSP
directory.
See the Family17h documentation in the coreboot documentation directory
for more information.
BUG=b:137338769
TEST=Build, add test binary to mandolin board, boot
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I29002a1af51c59a2e6c715e15f3dc63e59cd5729
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
- Correct command line argument for microcode patches from -u to -O
- Add #if PSP_COMBO around new_combo_dir() as it's only called when
that's enabled.
- Remove unused variable in integrate_bios_firmwares()
- Correct enum type from amd_fw_type to amd_bios_type in
register_fw_addr()
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I51c6dbe700505bc2e32443000ae55cb644051e42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
SOR_LINK_SPEED_G5_4 is unsupported, but it is not invalid, so it
suffices to return here instead of printing the next warning message.
Change-Id: Ifca3c52635e9a39af42e6616821d1099c43c237c
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1293137
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
last_unitid is immediately overwritten in the do loop, so this assignment
is not needed. This a relic from old code that commit 13f1c2af8b made
obsolete, but was never removed.
Change-Id: I2eecddd025f7a64b0a70fc07a61ebb43aba757d6
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: scan-build 8.0.0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The JUnit output from the libpayload builds was getting deleted by the
coreinfo build. Move the libpayload to later in the coreboot-gerrit
job.
Also add messages to stdout indicating the various libpayload configs
that are built and a message indicating when all libpayload builds are
complete.
BUG=b:137380189
TEST=Upload test commit that includes a libpayload compile error and
verify buildbot fails.
Change-Id: I43b55f402216582dcf81be34171437be345572ab
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34183
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add generic WiFi driver to support common device operations across
multiple types of WiFi controller.
BUG=None
BRANCH=None
TEST=Boot to ChromeOS. Ensure that the SSDT table contains SAR tables
and wakeup GPE information. Ensure that the SSDT table is same after the
change.
Change-Id: Ica5edf95a37c8ed60f7e159d94fd58af5d41c0ef
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
CB:32870 changed FIT loading code to make an FDT mandatory (because the
platforms that can use FIT images always need an FDT). Remove one
left-over conditional that is now dead code.
Found by Coverity.
Change-Id: Ia7765d45f068ab4bdc720ea7ae87dcc62a4b7d3d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
SMM_TSEG is a qualifier between TSEG and ASEG only, while
HAVE_SMI_HANDLER currently tells if SMM will be installed.
Move rest of the file under same 'if ELOG' block.
Change-Id: I620d3ce5aa9632d862d6480922144f002cf6423b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34195
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GRUB 2.04 was released on July 5th, 2019, so update. The only change-log
is the git history. Some coreboot related changes are listed below.
1. coreboot: Changed cbmemc to support updated console format from
coreboot.
2. ahci: Increase time-out from 10 s to 32 s
3. normal/menu: Do not treat error values as key presses
When building from the git repository, `./bootstrap.sh` needs to be run
to set up Gnulib. Ignore the exit code, as older versions might not have
this script.
Change-Id: Iab0b87164ed86f15d3415af935998b59e0d76c45
Signed-off-by: Pablo <42.pablo.ms@gmail.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
We got rid of the dangerous reconfiguration of arbitrary pads in
coreboot, but FSP still overrode that. Make sure that it doesn't
enable a UART for debug output when it isn't configured in core-
boot.
This, again, shows how dangerous it is to leave any FSP UPD at
its binary default.
Change-Id: I7280a80f71ddddbe78352eb696e6f5844d2df0b2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
There are only minimal differences between the architecture specific
stdint.h implementations, so let's tidy them up and merge them together
into a single file. In particular,
- Use 'unsigned long' for uintptr_t. This was already the case for x86
and riscv, while arm and mips used 'unsigned int', and arm64 and ppc64
used 'unsigned long long'. This change allows using a single integer
type for uintptr_t across all architectures, and brings it into
consistency with the rest of the code base, which generally uses
'unsigned long' for memory addresses anyway. This change required
fixing several assumptions about integer types in the arm code.
- Use _Bool as the boolean type. This is a specialized boolean type that
was introduced in C99, and is preferrable over hacking booleans
using integers. romcc sadly does not support _Bool, so for that we
stick with the old uint8_t.
- Drop the least and fast integer types. They aren't used
anywhere in the code base and are an unnecessary maintenance burden.
Using the standard fixed width types is essentially always better anyway.
- Drop the UINT64_C() macro. It also isn't used anywhere and doesn't
provide anything that a (uint64_t) cast doesn't.
- Implement the rest of the MIN and MAX numerical limits.
- Use static assertions to check that the integer widths are correct.
Change-Id: I6b52f37793151041b7bdee9ec3708bfad69617b2
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In patch e29a6ac16a (util/sconfig: Add
commonlib/helpers.h) helpers.h has been added to the include-list.
In headers.h we have a definition for __unused:
On a host system environment where glibc-headers-2.12-1.212 is
installed, a file included by <sys/stat.h> called bits/stat.h have the
following content on line 105 and onwards:
long int __unused[3];
where the mentioned part is part of the structure called struct stat.
If we include commonlib/helpers.h _before_ <sys/stat.h>, the symbol for
__unused will be defined by the preprocessor to be
'__attribute__((unused))', therefore the above mentioned structure member
will be expanded by the preprocessor to be
'long int __attribute__((unused))[3];', which is not a valid C syntax
and therefore produces a compile error for sconfig tool.
To handle this case we need to make sure commonlib/helpers.h is included
_after_ <sys/stat.h>. As the needed part of stat.h (which is
struct stat) is only used in main.c it is safe to move the include from
sconfig.h directly into main.c while taking care of the order.
Change-Id: I9e6960a318d3dd999e1e9c1df326d67094f3b5ce
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
It is recommended to never reference PCI busses
using a static number. There is exception with
OPROM execution, where we want to translate the
bus number captured from the actual IO operation
into a matching device node in the devicetree.
Change-Id: I733c645ac5581c000b4cd6cdc05829cd039324d5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Currently some of the LCM ID voltage gaps are below 100mV. For example, the
voltage difference between ID 2 and 3 is 503-440=63mV. To reduce the risk of
misrecognition from the hardware level, the voltages are adjusted so that all
the voltage gaps are larger than 100mV. The RD2 resistor values are also
updated.
BUG=b:136987483
TEST=emerge-kukui coreboot
Change-Id: Ib5c1f927fb54d8c9579f030e42eeec5a27daaceb
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34192
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The tolerance of ADC is +-10mV, but the resistors may also
introduce 1% variation, and causing the final measured
voltage to vary around 5%.
By the advisory from hardware team, checking the tolerance
seems not really solving or helping anything so we should
just ignore that and try to find best matched ID (this
also aligns to what Gru did).
BUG=b:136990271
TEST=Booted on Krane and no longer seeing ADC out of range
BRANCH=None
Change-Id: Ie02ca5aaafbcfa8f411d973ad0266eee385d6878
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34161
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Before the system enters S0ix or S3, each GPIO community
will have its dynamic clock gating turned on. Upon return
to S0, the dynamic clock gating will be turned back off.
BUG=b:130764684
BRANCH=none
TEST=Used dut-power to verify that the clock gating is enabled
in S0ix and S3. Also used Store(..., Debug) statements in the
ASL code to verify it was getting called.
Change-Id: I20ff2aac035eaa5912af6c946d837567a4918bbf
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Clang Static Analyzer version 8.0.0 detects that the result of
log2_ceil(bios_size) and log2_ceil(window_size) is undefined if the
value of bios_size and window_size are negative. Add negative value
Check for bios_size and window_size after MIN operation.
Change-Id: I28577b6e0ba0ab45bb7804c17ba1f26c4b078b15
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
HP_INT_L(GPP_H0) is configured for GPIO IRQ instead of APIC IRQ since
it needs to trigger on both edges. With GPIO IRQ, it is necessary to
configure the trigger type in coreboot to match the ACPI
configuration. This is because:
1. ACPI configuration is used by intel-pinctrl driver in Linux kernel
to re-configure the trigger type for the pad in GPIO DW0 config
register. This is done when kernel driver probes and requests irq for
its device.
2. On resume from S3, the pad configuration gets reset and coreboot
sets the trigger type to LEVEL. However, kernel driver does not probe
again. This results in the trigger type being configured incorrectly.
This change updates the GPIO configuration for GPP_H0 to set the same
trigger type as advertised in ACPI for the kernel.
BUG=b:132672011
TEST=Verified that S3 works fine. Verified that interrupt on GPP_H0
works fine on boot as well as after suspend/resume.
Change-Id: Ieb44c7403a2f4911b4a8f422053dee8bcfb91d85
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34181
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit b19946cc62 (console: Remove support for printing extra bases)
truncated the digits string to only print integers of up to base 16.
However, that string was also used to print the leading 'x' or 'X' for
hexadecimal integers and is now too short. Fix this to prevent an out
of bounds read.
Change-Id: Iab6470cc88f445f074cf7c0b675346b37f3f2375
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1402999
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Julius Werner <jwerner@chromium.org>
These printk() statements were added in commit cdc526e582
(southbridge/nvidia/ck804: Fix boot hang on ASUS KFSN4-DRE w/ K8 CPU)
when debugging another issue. They have undefined reads if ck804_num
is 0 and aren't needed anymore, so drop them.
Change-Id: I80b775370ac6485958948f0bff4510755a6cd2b8
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 137058{1,3}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33459
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Check for FSP HOBs is depending on CONFIG_DISPLAY_HOBS.
Use the CONFIG_DISPLAY_HOBS for display HOB info only and always check HOBs.
Use BIOS_ERR of printk() for FSP errors.
BUG=N/A
TEST=Check console output on Facebook FBG1701.
Change-Id: I3776fa37866c7ef3aea090842387660c22bbdd4d
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
AMD Picasso, and later, will not use CPU_AMD_AGESA or CPU_AMD_PI.
Those two symbols indicate an Arch2008 system. Add SOC_AMD_COMMON
to cause cpu_is_amd() to return TRUE on Picasso.
This removes an error message of "Unknown CPU".
The patch also assumes AMD Family 10h and non-AGESA Family 15h
devices were seeing the "Unknown CPU" message. No functionality
has been verified on these devices.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I3357606c37082f3587ff91924bf7a0e0f8af9625
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34146
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With DEVTREE_EARLY we could create incomplete device
objects with topology links removed to reduce footprint
for bootblock.
Declare everything with 'static __unused DEVTREE_CONST'
to avoid compiler errors and to not expose unusable
device object names to global scope.
Change-Id: Ie4cb9e75f179f44edf4f8256ad8320bc2d4ae71a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
- Remove unnecessary braces
- Move variable assignment out of function call
- Do not find lowest bit set of 0, which is undefined
- Use unsigned integer when bit shifting
Change-Id: I8651f8cd04165d8d31c44f7919ad5e43499d3d4c
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1229562
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Only CONFIG_USE_INTEL_FSP_MP_INIT makes a difference whether native MP
init is used or not.
Also make USE_INTEL_FSP_MP_INIT mutually exclusive with
USE_INTEL_FSP_TO_CALL_COREBOOT_PUBLISH_MP_PPI as this option requires
coreboot to set up AP and publish PPI based on it.
Change-Id: I65b80805d3cd7b66f8c9f878d3c741b98f24288d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33357
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
digest from vb2_digest_bufer() does not contains the correct endian.
Create cb_sha_endian() which can convert the calculated digest into big endian
or little endian when required.
BUG=N/A
TEST=Created binary and verify logging on Facebok FBG-1701
Change-Id: If828bde54c79e836a5b05ff0447645d7e06e819a
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
GNAT had a constant initialized at runtime which led to trouble
with compilers that decided to place it into an actual constant
section (e.g. GCC 9). Usually, this would be handled gracefully
if the Ada compiler knew about the runtime initialization. How-
ever, as the initialization was done by taking the address of
the variable, the compiler had no clue.
Change-Id: I73ce4cadc612c814ed2e22b44f429af2ad3db288
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34147
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates the following GPIO settings.
1. Set Native termination for GPP_G0 - G4 SD card pins.
2. Set GPP_B19 to NF1.
BUG=b:123907904
TEST=Verified SD card functionality on hatch. Checked for SD detection,
transferred files to and from SD card.
Change-Id: I4549ac7377d7f58f51cda0eb96a62604fd31d2f2
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
DCXO consists of core that generates clock and output buffers that
provide clock to other peripheral components.
This patch mainly eliminates the extra power consumption of output buffers.
We only enable the buffer for SOC and disable unused buffers for power-saving.
Also disable useless buffer power mode to guarantee the lowest power state.
BRANCH=none
TEST=Boots correctly on Kukui.
Change-Id: I2e5ce181ad327ccf852979da53baca4f249912fe
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32323
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Considering the following integer multiplication:
u64 = u16 * u16
What on earth, one might wonder, is the problem with this? Well, due to
C's unfortunately abstruse integer semantics, both u16's are implicitly
converted to int before the multiplication, which cannot hold
all possible values of a u16 * u16. Even worse, after overflow the
intermediate result will be a negative number, which during the
conversion to a u64 will be sign-extended to a huge integer. Not good.
The solution is to manually cast one of the u16 to a u32 or u64, which
are large enough to not have any overflow and will prevent the implicit
conversion. The type of the u64 is preferred, though a u32 is used
instead of size_t, since that can change depending on the platform.
Change-Id: I5391221d46d620d0e5bd629e2f9680be7a53342e
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 12297{03,04,05,06,07,08,09,10}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
size_t is the wrong type to store the return value of
acpi_device_path_fill(), since any negative error values will be
converted to a very large unsigned integer and potentially cause
buffer overflow.
Change-Id: Ia8ed62ecfac8eaa18a61545bd203b3c7a7cd9ca5
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1402095
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This function executes the cpuid instruction, which takes a 32 bit input
value (idx), and then stores output in eax, ebx, ecx, and edx, which are
all 32 bit registers. Update the prototype to use fixed-width integers,
and update all usage calls appropriately.
Change-Id: I15876fa35628d3a505864fb49be4fdab1fd19f4a
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This config option, when set, will allow the platform to skip display
initialization in normal (non-developer, non-recovery) mode. This allows
platforms that do not implement firmware UI in normal mode to skip the
display init in firmware.
TEST=Set option CONFIG_VBOOT and clear CONFIG_VBOOT_MAY_SKIP_DISPLAY_INIT
and the display should initialize in ramstage when platform boots. Set
CONFIG_VBOOT and set CONFIG_VBOOT_MAY_SKIP_DISPLAY_INIT and the display
initialization should be skipped in coreboot.
Signed-off-by: Sukerkar, Amol N <amol.n.sukerkar@intel.com>
Change-Id: Icadad6da34dcb817af02868e89a94ea62dbfa7b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
G505S doesn't have any SAS or NVMe controllers and couldn't have a TPM,
so it makes sense to disable the related SeaBIOS options for this board.
This reduces the size of compiled SeaBIOS by 129344-110048=19296 bytes.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: Ib0183b7786ecd77bb0df923bc84908275f2fe14c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33870
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change intentionally removes the definition of PCH_DEV_PMC from
ramstage to avoid silent errors. This device gets hidden from PCI bus
in FSP-S and hence dropped from the root bus by the resource
allocator. In order to avoid incorrect references to the device, avoid
defining it in ramstage where it known to return NULL.
BUG=b:136861224
Change-Id: I4f69470ec80c7127a2b604ed2b1f794f5a63e126
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34120
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PMC device gets hidden from PCI bus after FSP-S call. Thus, it gets
removed from the root bus as leftover unused device. With change
903b40a8a4 ("soc/intel: Replace uses of dev_find_slot()"), all uses
of dev_find_slot() were replaced by pcidev_path_on_root() which relies
on scanning of root bus to find the requested device. Since PMC device
is removed from the root bus, pcidev_path_on_root() returns NULL for
it thus resulting in configuration being skipped for the PMC
ultimately resulting in S3 failures.
Since the PCH_DEV_PMC was just used to get to chip config, this
change replaces the use of PCH_DEV_PMC with SA_DEV_ROOT.
BUG=b:136861224
Change-Id: Id68db8382b7b98e8e2e4a65ded1a6fb3bd057051
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
PMC device gets hidden from PCI bus after FSP-S call. Thus, it gets
removed from the root bus as leftover unused device. With change
903b40a8a4 ("soc/intel: Replace uses of dev_find_slot()"), all uses
of dev_find_slot() were replaced by pcidev_path_on_root() which relies
on scanning of root bus to find the requested device. Since PMC device
is removed from the root bus, pcidev_path_on_root() returns NULL for
it thus resulting in configuration being skipped for the PMC
ultimately resulting in S3 failures.
Since the PCH_DEV_PMC was just used to get to chip config, this change
replaces the use of PCH_DEV_PMC with SA_DEV_ROOT.
BUG=b:136861224
TEST=Verified that S3 works fine on hatch.
Change-Id: Ie5ade00ac2aca697608f1bdea9764b71c26e2112
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
We have 3 similar Lenovo mainboards - x60 (oldest), t60, and z61t (most
recent addition). The only one with two consequent 2s as the C-types
is t60:
static acpi_cstate_t cst_entries[] = {
{ 1, 1, 1000, { 0x7f, 1, 2, { 0 }, 1, 0 } },
{ 2, 1, 500, { 0x01, 8, 0, { 0 }, DEFAULT_PMBASE + LV2, 0 } },
{ 2, 17, 250, { 0x01, 8, 0, { 0 }, DEFAULT_PMBASE + LV3, 0 } },
};
It seems that 3 could be a better choice for the last line here.
UNTESTED on a real hardware.
Change-Id: I090e82d5f4ae25c768ff45a01a8dd76ff8a96a90
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Family 17h will not use the Arch2008 (a.k.a. v5) wrapper. Remove
all source, support functions, and comments related to AGESA.
Family 17h requires v9 which has no similarities to v5 for
integration into a host firmware. AGESA v9 support will be added
via subsequent patches into the appropriate locations.
Change-Id: Iea1a41941a0ba364a6abaaf31cc8e1145db4a236
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
When system shuts down, RTC enable eosc calibration feature to save
power. Then coreboot RTC driver needs to call rtc_enable_dcxo function
at every boot to switch RTC clock source to dcxo.
BUG=b:128467245
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Iee21e7611df8959cbbc63b6e6655cfb462147748
Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Some of the values used for GPIO_CFG and MISCCFG were not correct,
causing GPEs to not work correctly. This adjusts them according to the
values found in the original ACPI tables for the System76 Gazelle.
Unfortunately, the Intel documentation[1] mentioned below is
also incorrect. I have mentioned this to Intel already. The source
for the Intel CoffeeLake FSP also confirms these new numbers.
This was tested on a System76 Gazelle (gaze14). The EC uses GPP_K3 for
its GPE and GPP_K6 is used for the lid switch GPE. Both function
correctly after applying this change.
[1] Intel Document #572235:
Intel ® 300 Series Chipset Families
Platform Controller Hub
External Design Specification (EDS) - Volume 2 of 2
Change-Id: I4ecc9552468037598ef5d4e10122d660dcbfe71d
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
While running the s0ix cycling test, we observed SMM Handler caused
a stack overflow. This error happens during event log access.
This change is to increase the SMM_MODULE_STACK size to 0x800
BUG=b:135551854
TEST=suspend_resume test pass 500+ cycles, originally issue happenes
within 150 cycle
Change-Id: Ib4686b4d2d4fc3976068779314f4ee15ef4a8ae2
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
To call dev_find_slot(0, xx) in romstage can produce
invalid results since PCI bus enumeration has not
been progressed yet.
Replace this with method that relies on bus topology
that walks the root bus only.
Change-Id: I2883610059bb9fa860bba01179e7d5c58cae00e5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Like the line above it, this should be & instead of | (otherwise it will
always incorrectly return true). spi_locked() is only used internally to
decide which opcodes will be used to talk to the flash, and if it is
falsely reported as locked, the worst case should be a denial of service
(unless there are more bugs).
Change-Id: I5208b523c815d15d7263594f06ccfacd8a9510b1
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1402092
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
With VBOOT=y && VBOOT_MEASURED_BOOT=y message
digest will be allocated from the stack and
1 KiB reserve used with the recent platforms
was no longer sufficient.
The comment of LZMA scratchpad consuming stack
was obsolete for postcar, so these can be reduced
to same 4 KiB.
Change-Id: Iba1fb5bfad6946f316feac2d8c998a782142a56a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Use of romstage_ram_stack_bottom() was invalid, it
potentially uses a different ROMSTAGE_RAM_STACK_SIZE
from the postcar_frame_init() call.
If alignment evaluated to 1 MiB, that WB MTRR may not
have covered all of CBMEM range, having some impact
on boot speeds.
There is no need to accurately describe write-back
MTRR ranges for postcar.
Change-Id: Icb65cef079df56fadcc292c648cab8bdbb667f47
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Remove the mailbox call to notify the PSP that DRAM is ready. This
is not supported on Family 17h.
Remove the selectable SMU firmware. This is a feature of the PSP
bootloader and the standard bootloader doesn't contain the ability.
Clean up additional mentions of PSP within picasso.
Change-Id: I8abeb4c375dbff3b438cd18ccaaf66e11c86e72e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Picasso doesn't implement the AcpiMmio XHCI_PM registers. Remove
source that uses these. Remove USB devices from the AOAC registers.
Remove the D0/D3 support from ASL, including all supporting xHCI
firmware loading support. Remove xHCI firmware from amdfw.rom.
Change-Id: Iae4c72c5a8e353ca8db02d04735f8d2b28441793
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Add a utility to generate a compressed BIOS image for AMD Family 17h.
If the input is an elf file, the utility extracts the program portion
for compression. Otherwise the file is compressed as-is.
In modern AMD systems, the PSP brings up DRAM then uncompresses the
BIOS image into memory prior to x86 beginning execution. The PSP
supports a zlib engine, and interprets the first 256 bytes as a
header, where offset 0x14 containing the uncompressed size. For
further details, see AMD Platform Security Processor BIOS Architecture
Design Guide for AMD Family 17h Processors (NDA only, #55758).
BUG=b:127766506
TEST=Use with WIP Picasso
Change-Id: Id1c54e0a6dae9e4a0362c6635fe8b8aa48a369d8
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
When we added CONFIG_VBOOT_MIGRATE_WORKING_DATA, the idea was that on
some Arm platforms the original working data buffer was in SRAM, which
stays accessbile for the whole runtime of the system. There is no reason
to migrate it into CBMEM on those platforms because ramstage and the
payload could continue to access it in SRAM.
Now that we've had a couple of months of experience with this option, we
found that most of our Arm platforms have some issue that requires
migrating anyway, because BL31 often claims SRAM for itself and makes it
inaccessible to the payload. On the remaining platforms, accessing SRAM
from the payload is possible but still an issue, because libpayload
doesn't have enough memory layout information to set up proper page
tables for it, so we're accessing it uncached and at risk of alignment
errors.
Rather than having to figure out how to map the right SRAM range for
every platform in the payload, let's just get rid of the option.
memcpy()ing 12KB isn't worth this much hassle.
Change-Id: I1b94e01c998f723c8950be4d12cc8f02b363a1bf
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The flag is useful for updaters to determine which areas to leave
alone, such as VPD (vital product data) regions that are set in
factory and might contain unique (MAC addresses) or hard to obtain
(calibration output) data.
It's also useful to see which regions are marked as such.
Change-Id: Ic0a229d474b32ac156cfabc917714ce9d339bac6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33604
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Increase the timeout for USB requests to 5 seconds for all USB host
controllers.
Prior to this fix, the xCHI driver was detecting false timeouts during
SET ADDRESS requests when nested downstream hubs were connected to the
xHCI root hub.
BUG=b:124730179
BRANCH=sarien
TEST=Build libpayload and depthcharge on sarien/arcada.
TEST=Without change replicate USB set address timeouts in depthcharge
when dock and 4K monitor connected (which includes a total of 4 USB
hubs). With timeout fix, depthcharge boots OS with no USB errors and
the same USB topology. Note that this tests xHCI operation only.
Change-Id: I53e3e67d893420e7c9e8b52c47dd0edb979e5468
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Also don't define the default as this results in spurious lines in the
.config.
The only difference in the generated config.h is that for most board
ARCH_RISCV_M goes from 1 to 0. This should not matter.
Change-Id: I3e8c1cc5696d621e243696a3b5e34f62ab69a688
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31311
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enhance elog wake source information with more details about which USB port
resulted in a wake from S3 or S0ix.
BUG=b:123429132
BRANCH=none
TEST=``FW_NAME=hatch emerge-hatch chromeos-ec depthcharge vboot_reference
libpayload coreboot-private-files intel-cmlfsp coreboot-private-files-hatch
coreboot chromeos-bootimage``
Ensure /build/hatch/firmware/image-hatch.serial.bin has been built.
Plug a keyboard into a USB port on the DUT.
Switch the DUT to the console (Ctrl-Alt-F2, or use the AP console via
servo).
On the console, run ``powerd_dbus_suspend``.
Wait for the DUT to enter low power mode.
Verify low power mode by issuing the ``powerinfo`` command on the EC
console (via servo). Expect to see ``power state 4 = S0ix``.
Press a key on the USB keyboard.
The DUT wakes up.
On the console, run ``mosys eventlog list`` and look for the wake source.
156 | 2019-06-26 09:46:07 | S0ix Enter
157 | 2019-06-26 12:14:05 | S0ix Exit
158 | 2019-06-26 12:14:05 | Wake Source | Internal PME | 0
159 | 2019-06-26 12:14:05 | Wake Source | GPE # | 109
Program image-hatch.serial.bin into the DUT using flashrom.
Repeat the ``powerd_dbus_suspend``, ``powerinfo``, ``mosys eventlog list``
sequence.
12 | 2019-06-26 14:52:23 | S0ix Enter
13 | 2019-06-26 14:53:07 | S0ix Exit
14 | 2019-06-26 14:53:07 | Wake Source | PME - XHCI (USB 2.0 port) | 3
15 | 2019-06-26 14:53:07 | Wake Source | GPE # | 109
Change-Id: Ie9ef870e219733dea9806c766f5351db25689b32
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Previously, We had to use GPP_A21 for trackpad wake and GPP_D21 for
trackpad interrupts due to ITSS not honoring the INVERT config. Now
that's fixed, we can configure trackpad wake and interrupts on GPP_A21
only.
BUG=b:130436471
BRANCH=None
TEST=1. boot a hatch device and make sure we can move the cursor with the trackpad
2. Run powerd_dbus_suspend and wake by clicking on the trackpad and ensure
through "mosys eventlog list" that the wake source is the trackpad.\
3. Run "echo mem > /sys/power/state", wait until device goes into S3,
click trackpad to ensure device wakes.
Change-Id: I26a99206c42ba442f91ae577b98366fc2fd6c0ca
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Now that ITSS config is fixed, we can set the IOAPIC pad configs
correctly.
BUG=b:123967687
BRANCH=None
TEST=Make sure Hatch is booting and tested out trackpad to make
sure can move cursor and wake by clicking on the trackpad
after running powerd_dbus_suspend.
Change-Id: I0b125996338b6f16e03b7ca184f6337c696a5f64
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33819
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove all Picasso bootblock support. CAR is not a supportable
feature, and the first code executed at the reset vector will be
a hybrid romstage. Details for this implementation may be found
in Documentation/soc/amd/picasso/family17h.md.
TEST=None
BUG=b:130804851
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I8edf45c02dc5bfcdca03abf1294db4be508682cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Remove files that aren't needed for the picasso port.
Remove traces of AGESA v5 (includes binaryPI support files). Remove
SPD helper.
Picasso (and all AMD Family 17h processors) have a very different
boot flow from previous products. Memory is initialized by the PSP
before the x86 processor is released from reset. The SPD is read by
the PSP, so it's not needed in coreboot.
TEST=None
BUG=b:130804851
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I743ffd6058982f8f182ea4d73172a029967f3ea5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
So that everyone can see what's being updated from stoney, we're
starting with a direct copy of the stoney directory. There are
arguments both for and against doing it this way, but I believe
This the most transparent way. We've moved much of the duplicated
stoney code into the soc/amd/common directory and will continue
that work as it becomes obvious that we have unchanged code between
the SOCs.
Makefile.inc has been renamed as makefile.inc so that it won't
build in jenkins until the directory is updated.
Other than that change, this is an exact copy of the stoneyridge
SOC directory which will be updated in the follow-on commits in
the patch train.
TEST=None
BUG=b:130804851
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I6809bd1eea304f76dd9000c079b3ed09f94dbd3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32407
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For the PCI_VENDOR_ID_ATI case, we can rely on
pci_rom_acpi_fill_vfct() to make the call if necessary.
For hardware other than ATI, pci_rom_probe() was already
called from pci_rom_ssdt() and pci_dev_init(), so
PCI_ROM_ADDRESS BAR is already enabled, if requested so.
Change-Id: I0ea893a9ac7ba480840ebf5570d8fe0d9e20938f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
The function pci_rom_probe() may be called multiple times
for a device. For cases where CBFS does not contain optionrom
file, only the first time probing for the on-board ROM
chip worked.
PCI_ROM_ADDRESS_ENABLE is set on the first run. Mask out all
the reserved bits of PCI_ROM_ADDRESS register to get correct
physical address for rom_header.
Change-Id: I14374954af09201494bf2f13e5a6e4dc640c05ee
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
* Add architecture independend way of clearing all DRAM
* Implemented in ramstage as MTRRs need to be set to speed up
clearing. Takes up to 15 seconds per GiB otherwise.
* Use memset_pae on x86
* Add quirks for FSP1.0
Tested on P8H61M-Pro:
* Clears 4GiB in less than 1 second
Tested on wedge100s:
* Clears 8GiB in 2 seconds
Change-Id: Idaadb8fb438e5b95557c0f65a14534e8762fde20
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31550
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To clear all DRAM on x86_32, add a new method that uses PAE to access
more than 32bit of address space.
Add Documentation as well.
Required for clearing all system memory as part of security API.
Tested on wedge100s:
Takes less than 2 seconds to clear 8GiB of DRAM.
Tested on P8H61M-Pro:
Takes less than 1 second to clear 4GiB of DRAM.
Change-Id: I00f7ecf87b5c9227a9d58a0b61eecc38007e1a57
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31549
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Banner string format has been changed (CB:30935). We should update our
regular expression correspondingly.
Also add "verstage" into the stage search list since some boards (e.g.,
Kukui) might start console initialization at verstage.
Change-Id: I16eba3ac5e203e80b0bfd42a4294401dbccd4463
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Fix error "Invalid option -A" by adding "A" to options list.
Also, atoi does not parse hex string, for instance 0x200 is interpreted as 0,
and this causes a failure when updating second FIT table using -j option.
Use strtol instead of atoi
BUG=none
BRANCH=none
TEST=Build and boot hatch after enabling dual bootblock feature.
Change-Id: Ib227437f88ffcccda1ce2f20a9ab098e5aa091c7
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
No message is reported in tlcl_lib_init() when tis_init() or tis_open()
returned an error value.
Add debug string.
BUG=N/A
TEST=Build binary and verified logging on Facebook FBG-1701
Change-Id: I522e488ddd3a1bd94a1a8c8470c757bd79c6d5c5
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Prior to commit
d731a24 src/cpu/intel: Set get_ia32_fsb function common
value of 200 was silently used as a default for fsp_rangeley
(model_406dx) in cpu/x86/lapic/apic_timer:set_timer_fsb().
After the commit, get_ia32_fsb() returns -2, eventually
resulting with divide-by-zero in timer_monotonic_get(), as
get_timer_fsb() returns 0.
Add Rangeley CPUID model 0x4d to get_ia32_fsb() as a fix,
using BCLK = 100 MHz based on the comments in
northbridge/intel/fsp_rangeley/udelay.c
Change-Id: I306f85dba9b1e91539fc0ecc9b2ae9d54f82be6c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This patch makes CONFIG_RAMPAYLOAD default enable upon selection
of HAVE_RAMPAYLOAD kconfig from mainboard for x86 platform.
Without this CL, CONFIG_RAMPAYLOAD is still disabled although
mainboard has selected CONFIG_HAVE_RAMPAYLOAD.
Change-Id: I40308bbf970a0dbe5f7e2086ed8a7a70c2a3a32c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33859
Reviewed-by: ron minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It looks like in days gone by that these switches were once parts of
loops that incremented 'index' as they went along. However, we don't
have any loops anymore, so remove the needless increments and streamline
the rest of the assignments.
Change-Id: Iaabee984333c273af7810f9c11ed26bbb2a995d1
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: scan-build 8.0.0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This function is duplicated in many AMD northbridge files, and all
the definitions have started to diverge somewhat. This moves a single
copy into device utils and deletes the rest. The function definition
from nb/amd/amdfam10 was chosen to be kept, since it contains several
fixes from commit 59d609217b (AMD fam10: Fix add_more_links) that
the others don't have.
For the ease of diffing, the checkpatch lints and other small cleanups
will be done in a follow-up patch.
Change-Id: I5ea73126092449db3f18e19ac0660439313072de
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33237
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
By default printram() expands to nothing in normal builds, and so
scan-build thinks that the assignment to reg8 is unused. Inline the
value of reg8 into the print statement to silence the warning.
Change-Id: I921fe08949c4135367bee9646b3b365097fab19e
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: scan-build 8.0.0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
FSP sets the use of the 8254 timer via the Enable8254ClockGating
UPD, which defaults to enabled, overriding what is set by coreboot.
Per the FSP integration guide, this UPD needs to be disabled when
a legacy OS is booted (ie, when SeaBIOS is used as the payload).
Add a Kconfig option to set the UPD properly based on payload
selection, and remove the existing coreboot code in lpc.c since
it is either ineffective or being overridden by FSP.
Test: build/boot out-of-tree WHL board with both SeaBIOS and
Tianocore, ensure 8254 timer usage set correctly for each.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: I0e888bf754cb72093f14fc02f39bddcd6d288203
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
* Add support for Linux 5.x
** Select PCI, which isn't the default anymore with 5.x
** Select google firmware driver, which wasn't build any more
* Add support for Intel LPSS uart
** Select MFD and MFD_INTEL_LPSS_PCI
** Increase console count to 32
* Add support for coreboot framebuffer
** Select FB_SIMPLE
* Add support for eMMC/SDHCI
** Select MMC_SDHCI_*
* Add support for u-root's localboot
** Select KEXEC_FILE_LOAD
** Select FIRMWARE_MEMMAP
Stats:
* Kernel size 1.9MiB
* U-root (core + systemboot) 4.6MiB
Tested on Intel APL Up² board:
* Fixes non working console on APL Up2 board and eMMC bootmedia shows up.
* Allows to boot GNU/Linux from eMMC using 'localboot'
Change-Id: Ib5bd33531741e588ac7d5ff6a02b0482f6655ddf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33581
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
By default, the LPC SIRQ mode is set to Quiet mode. Therefore, COM-port
from the SurerIO chip don't work correctly after the LPC controller (PCI
0:1f.0) initialization. Console output is broken. The patch fixes this
bug by overriding the serirq_mode option in the devicetree.cb to set
Continuous SIRQ mode
Change-Id: I37e26b271fb61f6c0343d6bf65c029924df82caf
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33801
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add files to introduce a memory clearing framework.
Introduce Kconfig PLATFORM_HAS_DRAM_CLEAR that is to be selected by
platforms, that are able to clear all DRAM.
Introduce Kconfig SECURITY_CLEAR_DRAM_ON_REGULAR_BOOT that is user
selectable to always clear DRAM on non S3 boot.
The function security_clear_dram_request tells the calling platform when
to wipe all DRAM. Will be extended by TEE frameworks.
Add Documentation for the new security API.
Change-Id: Ifba25bfdd1057049f5cbae8968501bd9be487110
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Depthcharge no longer reads this data structure, and uses
the vboot workbuf in vboot_working_data instead.
Since vboot2 downstream migration is not yet completed, the
vboot2 -> vboot1 migration code is still required, but has
been relocated to depthcharge.
BUG=b:124141368, b:124192753
TEST=make clean && make runtests
BRANCH=none
Change-Id: I769abbff79695b38d11fb6a93c2b42f64d4bafde
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33535
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A FPMCU power-control pin (GPP_C11) is added to the latest
hatch reference schematic.
Even though this is not implemented in hatch rev1 board, the future
hatch family boards with FPMCU should all have this control pin.
On the old boards without this control pin, GPP_C11 is a floating TP,
and thus this patch should be backward-compatible.
BUG=b:130307667, b:135216932
TEST=build
Signed-off-by: Philip Chen <philipchen@google.com>
Change-Id: I6a84eeb6aab562258e749a8a5d09dadfa0e43587
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
tc348860_table contains the eDP to MIPI Bridge controller type.
b101uan08_table used the LCD Panel type.
Use LCD Panel type for name of tables.
Remove the incomplete resolution comments and specify the resolution at
the start of the table to 1200x1920.
BUG=N/A
TEST=Config eDP and verify LCD panels are working on Facebook FBG-1701
Change-Id: Ic152ea1f95f155ab76638b57a259d37ce6f43037
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33736
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It seems that the EC on t60/x60/z61t doesn't support it. This wasn't
even introduced in z61t so let's remove the remaining bits.
This commit follows up on commit a5fcc2e4 with Change-Id
Id2964002406a5fcf992f0ffc3627e3f66a2bb13f ("mb/lenovo/x60/t60: Remove
`fn_ctrl_swap` option").
Tested on a real hardware.
Change-Id: Ifd5e7823af305cc4a0194ee2097a749e43680c55
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Andrey Korolyov <andrey@xdel.ru>
Sometimes coreboot needs to compile external code (e.g.
vboot_reference) using its own set of system header files. When
these headers don't line up with C Standard Library, it causes
problems.
Create ctype.h header file. Relocate ctype.h functions from
string.h into ctype.h. Update source files which call ctype.h
functions accordingly.
Note that ctype.h still lacks five functions which are not used
in coreboot source:
isalnum, isalpha, iscntrl, isgraph, ispunct
BUG=b:124141368
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I31b5e8af49956ec024a392a73c3c9024b9a9c194
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested with SeaBIOS as a payload, booting Arch Linux with
a Linux kernel. The new code is based on autoport and the
existing GA-H61M-S2PV code.
The GA-H61M-S2PV has been boot-tested too, it still boots.
Working:
- S3 suspend/resume
- USB ports and headers (Intel USB2 and EtronTech USB3)
- Gigabit Ethernet
- Integrated DVI/VGA graphics (libgfxinit)
- PCIe x16 graphics
- PCIe x1 ports
- PS/2 port with a keyboard
- SATA controllers (Intel SATA2 and Marvell SATA3)
- User-space fan control (fancontrol on Linux)
- Native raminit (4+4GB DDR3-1333)
- flashrom, using the internal programmer. Tested with coreboot,
as well as with the vendor firmware. Backup chip is untested.
Untested:
- VGA BIOS for integrated graphics init
- Audio: Only front/read outputs has been tested.
- Non-Linux OSes
- ACPI thermal zone and OS-independent fan control
Not working:
- Default IFD defines the BIOS region as the entire flash chip.
Using 'flashrom --ifd -i bios' is asking for a failed flash!
Change-Id: I37928de158bb8fbb47fbda5d1ccd4efba7edab26
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Depend on ifittool and use it to update FIT instead cbfstool FIT code.
Move the TOPSWAP / microcode handling out of cbfstool and implement it
in the Makefile.
The new FIT looks like the old one and has been tested on Broadwell-DE.
The TOPSWAP / microcode code path needs test on real hardware.
Change-Id: I687469d62557f81e9d88398cfc93182164fdac95
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Add the IntelFirmwareInterfaceTable-tool to modify the FIT.
As cbfstool is overloaded with arguments, introduce a new tool
to only modify FIT, which brings it's own command line syntax.
Provide clean interface to:
* Clear FIT
* Add entry to CBFS file
* Add entry to REGION
* Delete entries
* Add support for types other than 1
* Add support to dump current table
* Add support for top-swap
* Sort entries by type
Most code is reused from existing cbfstool and functionality of cbfstool
is kept. It will be removed once the make system uses only ifittool.
Based on "Intel Trusted Execution Technology (Intel TXT) LAB Handout"
and https://github.com/slimbootloader/slimbootloader .
Change-Id: I0fe8cd70611d58823aca1147d5b830722ed72bd5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
This patch relying on new rule, ENV_PAYLOAD_LOADER which is set
to ENV_RAMSTAGE.
This approach will help to add future optimization (rampayload) in
coreboot flow if required.
Change-Id: Ib54ece7b9e5f281f8a092dc6f38c07406edfa5fa
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: ron minnich <rminnich@gmail.com>
Fixes a logic error that sets MPIE, but didn't use mret to return to the payload.
This left MIE set to an undefined value.
Now all modes are handled the same way:
- Trap vector base address point to the payload
- Disable Interrupt
- Return to payload using mret
TEST=Run an M-mode payload
Change-Id: Iaab595f916949c57104ec00f8b06ea047fe76bba
Signed-off-by: Xiang Wang <wxjstz@126.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33462
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FBG1701 contains a TC358860 eDP to MIPI Bridge controller which needs
to be configured.
Add mainboard_configure_edp_bridge() to program the controller.
CPLD version is used to determine which table must be programmed.
The eDP is an i2c slave which expects the next i2c bus data for block
write:
<Slave Addr> <Reg Addr[15:8]> <Reg Addr[7:0]> followed by data with LSB
first.
BUG=N/A
TEST=Config eDP and verify LCD panels are working on Facebook FBG-1701
Change-Id: I262cb4376b86db94e3bb9522c556b5cc3ff38335
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
* Add chips ops for IPMI KCS.
* Get IPMI version over KCS.
* Generates ACPI SPMI table for IPMI KCS.
* Generates SMBIOS type 38 for IPMI KCS.
* Generates ACPI SPMI device for IPMI KCS on LPC device.
* Add documentation
To use this driver on BMC that support KCS on I/O:
1. Add an entry to the devicetree.cb:
chip drivers/ipmi
device pnp ca2.0 on end # IPMI KCS
end
2. Select IPMI_KCS in Kconfig.
3. (Optional) enable LPC I/O decode for the given address.
Tested on Wedge100s.
Change-Id: I73cbd2058ccdc5395baf244f31345a85eb0047d7
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Support SAMSUNG KMDP6001DA-B425 and MICRON MT29VZZZAD8DQKSL EMCP LPDDR4X DDR
From the calibration log of MICRON MT29VZZZAD8DQKSL, we found
the begin pass range of RX window earlier than with other DDR type.
So need change the DQS starting offset to increase the scan range of RX window.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on EMCP DRAM
Change-Id: I5fcc8673a2fbd7ec3a8776ab61c57f8903ddda20
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Huayang Duan <huayang.duan@mediatek.corp-partner.google.com>
Garg proto build has 3 SKUs:
garg 2A2C DB: SKU ID - 1
garg HDMI DB: SKU ID - 9
garg LTE DB: SKU ID - 17
For SKU#9, VBT will need to be overridden to enable DDI_C output to HDMI
BUG=b:134912735
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage
Cq-Depend: chrome-internal:1380847
Change-Id: I6c0ec086496eaf217ea8e326f5084d886d0e698f
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The compat string matching code was mostly copied from depthcharge. One
of the few differences is that we now store the list of compat strings
we're willing to match in a list rather than an array. Since our lists
insert at the front, that means the strings are now ordered lowest to
highest (not highest to lowest like in depthcharge).
We did rewrite the compat_rank matching code to accomodate for that...
however, what we didn't do is remove the break-statement in the loop
that matches all compat strings. When we search the lowest priority
first, we can't abort the search as soon as we found a match -- we have
to keep looking because we might find a higher priority match later.
This patch fixes the issue so that my Kevin can actually match for
google,kevin-rev5 (and doesn't just jump at the first best google,kevin
match).
Change-Id: Ibe3d84bbce6de3cd49c746a667ae1ccfdc843105
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32874
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support to boot FIT image configurations consisting of
a base device tree and one or more overlays. Since extracting the right
compatible string from overlay FDTs is problematic, we'll only support
this for FIT images that have the compatible string pulled out into the
config node.
This patch was adapted from depthcharge's http://crosreview.com/1555293
Change-Id: I0943f9a1869c9e416887c7ff16e33f7d91b74989
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32873
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support for compressing individual device trees in the
FIT image. In order to make this efficient, we'll have to pull the
compatible property out of the FDT and store it directly in the config
node of the FIT image, so that we don't have to scan (and therefore
decompress) every single FDT on boot. Device tree compression is only
supported for FIT images that have this external compatible property.
For older images with no compression, we still support fallback to
scanning the FDT for the property.
This patch was adapted from depthcharge's http://crosreview.com/1553458
Change-Id: Ifcb6997782c480c8ef6692df17b66ad96264e623
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32872
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Kernel handoff on all architectures supporting FIT images already
includes flushing and disabling the cache. No need to waste any more
time flushing individual components (especially since in the case of
compressed DT overlays they will still get accessed again afterwards).
Change-Id: I7b483e920c5a71663b024b5b50804ffc84939830
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32871
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch makes some minor refactoring to the way the FIT parser
handles config nodes. A lot of this code was written in the dawn age of
depthcharge when its device tree library wasn't as well-stocked yet, so
some of it can be rewritten nicer with more high-level primitives.
There's no point in storing both the string name and the actual FDT node
of a FIT image node separately, since the latter also contains the
former, so remove that. Also eliminate code for the case of not having
an FDT (which makes no sense), and move some more FDT validity/compat
checking into fit_update_compat() (mostly in anticipation of later
changes).
This patch was adapted from depthcharge's http://crosreview.com/1553456
with a couple of modifications specific to coreboot's custom FIT loading
code.
Change-Id: Ia79e0fd0e1159c4aca64c453b82a0379b133350d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32870
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Code is based on microcode update procedure from fam10-15h with necessary
microcode blob structure updates for fam16h.
Currently updating microcode in romstage seem to be impossible. AGESA is
overriding the microcode patch regardles of the current microcode revision
patched on CPU. Use ramstage CPU init procedures to update microcode easily.
Tested with microcode blob 07030106 released 2018-02-09 from
platomav/CPUMicrocodes GitHub repository on apu2 platform.
TEST=boot Linux kernel 4.14.50 on PC Engines apu2 and run dmesg to see
patch_level=0x07030106 on all cores
Change-Id: Ic15cba06f3cd9cfbc538b6764b158fa699f0ecf6
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29272
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The DIMM manufacturing ID was not being initialized and so the DIMMs
were not described in SMBIOS tables properly.
The module type can also be provided, but the SMBIOS code expects
SPD module type values from DDR2 so the DDR3/4 values are adjusted
before sending to SMBIOS.
BUG=b:134897498
BRANCH=sarien
TEST=dump and compare with dmidecode
BEFORE:
Type: DDR4
Manufacturer: Unknown (0)
Form Factor: Unknown
AFTER:
Type: DDR4
Manufacturer: Hynix/Hyundai
Form Factor: SODIMM
Change-Id: Id673e08aa6e3dad196009c3c21a3dda2f40c9e42
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This function attempts to set bits in the 20s of state and state_save,
which won't work since those variables are only 16 bits wide. Extend
them to 32 bits to capture all the bit operations.
Change-Id: I5616a2d879a85ff5f57af5af20384516659c62d6
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1347384
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Files onboard.h and mainboard.h are not used for building.
Remove these files as include.
BUG=N/A
TEST=Build and boot embedded Linux 4.20 on Facebook FBG-1701
Change-Id: Ifeb0047357e641cbe1affbbaf5402213802c774c
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This does the following:
- select MAINBOARD_USES_FSP2_0 on Kabylake (does not support FSP1.1)
- Remove stale Kconfig option on intel/saddlebrook
- select SOC_INTEL_KABYLAKE on intel/kblrvp
Change-Id: I64f48eeb00150aea039d533b0ac471fdd8483b90
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
I increase the size oof the postcar stack to prevent a stack overflow
during the measured boot feature. After common string functions have
been moved from inline into .c file
(https://review.coreboot.org/c/coreboot/+/32901), I experienced a stack
overflow in the postcar stage while verifiying the romstage during
measured boot. To prevent this, the stack size should be increased. To
play it safe, it should be increased to 8 KiB - though this is open for
discussion.
Change-Id: I6f1a4631bcadfb8c7d1de5bf0919e40990a65606
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The correct address for vproc12 register of sw mode is 0x1426 instead
of 0x140a.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui and see that regulator is not stuck to
1.05V anymore:
grep vproc12 /sys/kernel/debug/regulator/regulator_summary
Change-Id: I13867b11c44019875e0ed607343197950a3b38b2
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33168
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clang doesn't know `-Wlogical-op`, so let's move it into xcompile where
we can easily distinguish between the two. However, this requires us to
split out `GCC_ADAFLAGS*` from `GCC_CFLAGS*`.
Change-Id: I6a50de0bc5372f61337f237383d32645ba86b0fd
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33579
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This code to handle the brightness from SMM is copied from the Lenovo
Thinkpad X60 code, but does not work on later generation. The PCI
device it tries to address does not even exist on those devices.
Change-Id: I0c25c3e5bec651b27158a84cc91289639a04ceb6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
tss_marshaling.c and tss.c depends on VBOOT for postcar.
Eltan vendorcode used function in these file, but has VBOOT disabled.
Remove depency of VBOOT for postcar fo tss/tcg-2.0/tss-marshaling.c and
tss/tcg-2.0/tss.c
BUG=N/A
TEST=Created binary and verify logging on Facebook FBG-1701
Change-Id: I195c79283abf403208f406518372bf52289772ed
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The upstream vpd_decode.c has been revised to prevent overrun of decoded
contents.
BUG=chromium:967209
TEST=select VPD config on kukui; make; boots on at least kukui boards.
Change-Id: I1a50670a66b7b174d2a432c29d90152b86c32982
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch enables TPM on SPI and adds the needed devicetree entry for
mc_apl5.
TEST=Build coreboot for mc_apl5 board and check the TPM console output.
In addition the TPM was correctly verified by our Linux driver.
Change-Id: Iafc967c7a2bfee9bdb9b6591d12328620e2887cc
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33173
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The values from auxadc may be incorrect if not calibrated by efuse.
Without calibration, the value error range is about +/-50mv,
and after being calibrated the error range is about +/-10mv.
BUG=b:131391176
TEST=make clean && make test-abuild; boots on Kukui rev 2 units.
BRANCH=none
Change-Id: Iccd6ea0ad810c993f9b62c0974279c960f890e52
Signed-off-by: Po Xu <jg_poxu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32800
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: JG Poxu <jg_poxu@mediatek.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adjust FMAP sections that
- ELOG only needs 4K (by driver limitation)
- SHARED_DATA only needs 4K or less (for netboot params)
- SMMSTORE is probably not needed since UEFI@ARM is not available yet
- VPD can be smaller (most x86 devices have only 16/8K for RO/RW)
- Increase RW_LEGACY to 1M (recommended value)
- Move all new saved space to CBFS
BUG=b:134624821
TEST=Built Kukui image and boots on Rev2 units.
Change-Id: Id2910df73ea47bfa32e056d631d1c3e5f1eed0d1
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Coverity believes there is a path where StdHeader is possibly
null. This *should* be incorrect, since the header is actually
initialized through the module dispatch framework, though Coverity
can't see it due to the extensive type-punning. However, the control
flow is so dizzingly complicated that I'm not even completely sure,
so adding an extra assert to be careful won't hurt anyway.
Change-Id: If3d7c5d5c5bba846e7453b3dbc824e2208d749fb
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1379932
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Logging and clearing the recovery mode switch doesn't have
anything to do with vboot_handoff. Move it to the main verstage
logic file.
BUG=b:124141368, b:124192753
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I2e74f3893463e43fe5fad4a8df8036560f34e0db
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33534
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
These functions are no longer used and may be removed:
* vboot_handoff_check_recovery_flag
* vboot_get_handoff_flag
BUG=b:124141368, b:124192753
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ie05652ef1288eef74bd2e7e8bea79fd29d523859
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33533
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Two functions retrieve vboot recovery_reason:
* vboot_handoff_get_recovery_reason
* vboot_get_recovery_reason_shared_data
Previously, when CBMEM comes online, a vboot_handoff data
structure is created, and depending on the architecture,
coreboot may eventually lose access to vboot_working_data.
After implementing vboot_working_data CBMEM migration,
vboot_working_data is always guaranteed to be accessible.
vboot_get_recovery_reason_shared_data is corrected to also
allow accessing vboot_working_data in ramstage and postcar.
Now, vboot_handoff_get_recovery reason returning a valid recovery
reason implies that vboot_get_recovery_reason_shared_data should
*also* return a valid recovery reason. Thus we may remove the
former.
BUG=b:124141368, b:124192753
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Iac216dc968dd155d9d4f8bd0f2dfd5034762f9a0
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The default voltage of vsim2 is set to 2.76V for sim card usage.
In general, 2.76V of vsim2 is composed of 2.7V main voltage and 0.06V calibration voltage.
However, vsim2 is used for the tx_ovdd power of display port IT6505 on the kukui board design which needs 2.7V.
So we set it to 2.7V with modifying calibration value.
BUG=b:126139364
BRANCH=none
TEST=measure vsim2 voltage with multimeter
Change-Id: I4dffdde89cbde91286d92e6c2b445f0b3d0ad2fe
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Intel Braswell supports i2c block writes using SMBus controller.
This support is missing in actual smbus routines.
Add do_i2c_block_write() which is a based on do_smbus_block_write() but
also write first byte to SMBHSTDAT1.
The caller needs to configure the SMBus controller in i2c mode.
In i2c mode SMBus controller will send the next sequence:
SMBXINTADD, SMBHSTDAT1, SMBBLKDAT .. SMBBLKDAT
To ensure the the command is send over the bus the SMBHSTCMD register must
be written also
BUG=N/A
TEST=Config eDP for LCD display on Facebook FBG-1701
Change-Id: I40f8c0f5257a62398189f36892b8159052481693
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Add arguments for additional PSP blobs needed with Family 17h support,
including the new AGESA binary loaders.
Create a new type of structure and entry for a BIOS directory table,
containing PMU code, microcode updates, as well as the BIOS initial
code.
Details on each of these items may be found in the AMD Platform Security
Processor BIOS Architecture Design Guide for AMD Family 17h Processors
(NDA only, #55758).
BUG=b:126593573
TEST=Used with WIP Picasso
Change-Id: I4899dedb6f5e29a27ff53787a566d5b8633a8ad5
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This was done to update the global variable g_ichspi_lock but this is
now removed in favor of reading the lock bit during runtime instead of
keeping track of the state.
Change-Id: I8cb69a152b0e050d64d8979ee92de2d24136f8dc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33390
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SPI swseq controller can be locked in other parts of the code, for
instance when it's locked down in the finalize section. The driver
has to be made aware of that. The simpler solution is to not keep
track of the state and simply read out the lock bit on each SPI
transfer.
Change-Id: Ifcd5121b89d6f80fc1c1368786982d0d9fa1bf61
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We had a value that was overloaded thrice.
By moving them in a common structure and ordering them by value such
issues are hopefully avoided in the future.
Also add a few values to libpayload that were only defined in
commonlib.
Change-Id: I227d078eebee2d92488454707d4dab8ecc24a4d8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32958
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Set abort command define
* Set debug level to SPEW
* Support zero length data packet in ipmi_kcs_send_message
That's required for commands like GET_DEVICE_ID, which have no
additional data to send.
* Read reply even if given no receive buffer
* Prevent buffer overflow in read reply processing
Tested on Wedge100s.
Change-Id: Iefddd88a744c3b96751d3fe8c2951ca2115548ce
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33488
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The temperature delta between on-board thermistor and
surface temp change, so update DPTF parameter accordingly.
BUG=b:113101335
TEST=Tested in thermal chamber by thermal team.
See comment 148 / 153 in the bug.
Change-Id: Ie18be94fc1e7476755fb0e6947cce559854a82dd
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
The sandybridge systemagent-r6 blob is modified:
- To be more flexible about the location of the stack w.r.t. the heap
- Place the MRC pool right below the MRC_VAR region
- to work with the same DCACHE_RAM_BASE from the native raminit (could
make the CAR linker symbols easily compatible if desired)
This allows CAR setup compatibility between mrc.bin and native
bootpath and also allows for BIOS/memory mappeds region larger than
8MB.
This changes the semantics of CONFIG_DACHE_RAM_MRC_VAR_SIZE to also
include the pool on top of MRC_VAR region.
TESTED on T520 (boots and resumes from S3 with mrc.bin).
Change-Id: I17d240656575b69a24718d90e4f2d2b7339d05a7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33228
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All usage of pci_read_config8 was removed in commit d44d4f0f with
Change-Id Ia959eb5b747846048396e66d4c926c96c27f3878 ("mb/lenovo/*:
Remove useless smihandler code"). So we don't need this include anymore.
Change-Id: Ic4f038c80e17799016ae7e92a5675cfe7c71e400
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This patch ensures to boot platform without onboard GFX (PCI B0:D2:F0)
enabled from mainboard devicetree.cb.
TEST=Previously platform was dying at "GMADR is not programmed!" with
IGD disabled.
Change-Id: I8c907ee25db4538a84890f2ccc3187afa86604b8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33449
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These if statements can be combined to merge the two branches of the
conditional and remove the duplicate pDCTstat->Speed == 3 check.
Change-Id: I41aa19b4b7ed7b1a0e4f83f72e66869760e677dd
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1229583
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Memory id's are 1-indexed for DDR4, so we need to check that the SPD
index is non-zero before converting it to the 0-indexed value in the
bitmap.
Change-Id: Icc542239d91c39b89c23f31856c28e7c20b2fc4d
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1387028
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The gpio_key wakeup_event_action in the ACPI tables was backwards, causing
devices to wake up on pen insertion instead of removal. Changed to
EV_ACT_DEASSERTED.
BUG=b:134547896
BRANCH=none
TEST=Verified in OS, device only wakes up on pen removal
Change-Id: I0816ed9fb23cf00fd8e40bcdd25ff7a9f48badbd
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33427
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change the SPD makefile to use the LPDDR3 SPDs. Set up the arrays
for mapping SoC DQS pins to LPDDR3 pins.
BRANCH=none
BUG=b:133455595
TEST=`FEATURES="noclean" FW_NAME="helios" emerge-hatch chromeos-ec
depthcharge vboot_reference libpayload coreboot-private-files
intel-cmlfsp coreboot-private-files-hatch coreboot chromeos-bootimage`
Ensure the firmware builds without error.
Change-Id: Iebaba2ec65dfcf36674b4733b421ada107b22b09
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33456
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We are seeing an EC interrupt after setting the EC RAM offset that
indicates that the EC should transition to S0ix mode and this is
preventing the kernel from going into S0ix on the first try.
As a workaround if we read back from the EC RAM while still in the
_DSM handler it seems to prevent this problem.
BUG=b:130644677
BRANCH=sarien
TEST=ensure s0ix entry works on the first try with sarien
Change-Id: Id607c4c2b14b79d0cd1bcea0c2032be2f2c0c141
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33455
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These 4 GPIOs are being disconnected in the next board so use the
board ID to configure these pins as not connected to ensure
they do not cause leakage.
Also remove the ACPI _PTS S5 code that was configuring the GPIOs.
This does mean they will cause small leakage in S5 on existing boards,
but it will not affect the new boards.
BUG=b:132393441
TEST=boot on sarien with fake board ID and ensure that coreboot
configures these pads as expected.
Change-Id: I6ac04b9a635829811a09aeab7cba3bb58cfcff47
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
These two functions try to access arrays of lengths 32 and 64 at indices
of at most 259 and 71 (respectively). Something here is seriously wrong.
This code was introduced in 2007, and aside from cosmetic changes, has
had no modifications since then. I don't know what this code is supposed
to do, and asking around on IRC, no one else did either. Until someone
has the interest and time to work on it, let's at least add a die() to
prevent the out of bounds access and alert the user that something is
wrong.
Change-Id: I5fc15a50a9f0e97add31e3a40da82a15f7427358
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 12296{79-82}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add the ability to generate two PSP directory table levels. The PSP
is capable of supporting two levels, with the primary intended to
remain pristine for the life of the system, and the second updatable.
In the event the second becomes corrupted, the primary is still
sufficient to allow a recovery of the other.
This patch modifies no directory table structures currently in use.
The soc or southbridge must pass an argument to force building the
secondary table.
BUG=b:126593573
TEST=Used with WIP Picasso
Change-Id: Id321f5142e461d4a7f3343c0835a09a1a1128728
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Allow the soc build to pass a soft fuse value to the utility. This
helps maintain compatibility across PSP generations.
Add a generic 'other' item to the amd_fw_entry structure that may
be used by non-fuse entries in the future.
TEST=Verify google/grunt amdfw.rom unchanged before and after.
Compare internal board using override before and after.
Change-Id: I26223f0b42ad28c43d9bd87419a2a8f719ee91cb
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This patch provides an additional option to skip HECI function
disabling using SMM mode for WHL and CML platform, where FSP has
dedicated UPD to make HECI function disable.
User to select HECI_DISABLE_USING_SMM if FSP doesn't provided dedicated
UPD.
Right now CNL and ICL platform will use HECI_DISABLE_USING_SMM kconfig
to make HECI disable and WHL/CML has to rely on FSP to make HECI
disable.
Change-Id: If3b064f3c32877235916f966a01beb525156d188
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
As per Icelake EDS PCI device B:D:F (0:0x1f:0) referred as ESPI,
hence modify SoC code to reflect the same.
This patch replaces all SoC specific PCI LPC references with ESPI
except anything that touches intel common code block.
Change-Id: I4990ea6d9b7b4c0eac2b3eea559f5469f086e827
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
No C_ENVIRONMENT_BOOTBLOCK support for Braswell is available.
Enable support and add required files for the Braswell Bootblock in C.
The next changes are made support C_ENVIRONMENT_BOOTBLOCK:
- Add car_stage_entry() function bootblock-c_entry() functions.
- Specify config DCACHE_BSP_STACK_SIZE and C_ENV_BOOTBLOCK_SIZE.
- Add bootblock_c_entry().
- Move init from car_soc_XXX_console_init() to bootblock_soc_XXX_Init()
Removed the unused cache_as_ram_main() and weak car_XXX_XXX_console_init()
BUG=NA
TEST=Booting Embedded Linux on Facebook FBG-1701
Building Google Banos
Change-Id: Iab48ad72f1514c93f20d70db5ef4fd8fa2383e8c
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Recovery path should finalize work context, and trim
vboot_working_data buffer_size. Otherwise, depthcharge ingests
the full 12 KB workbuf in recovery path.
BUG=chromium:972528, b:134893812
TEST=Build with vboot_reference CL:1584488. Check that USB disks
are properly verified in recovery path.
BRANCH=none
Change-Id: Icf2600d2eb5d846a26aec35a153946dd2f7f128c
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Disable dynamic clock gating for the community cr50's IRQ lives on.
That IRQ is pulsed very quickly, and with clock gating enabled pulses
tend to be missed. This is expecially true on the default 0.0.22
firmware that cr50 comes with out of the factory.
BUG=b:130764684 b:130338605
BRANCH=None
TEST=Boot hatch with cr50 "intap" firmware that can vary the pulse width,
observe that even with sub-microsecond pulses no IRQs are missed.
Change-Id: I34d14fb7cc97e33eecfda2c99cc53a541c87662d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The prototype of vprintk() is currently declared unconditionally, which
prevents it from being used in situations where the console is disabled.
The code will compile correctly, but not link, since the definition in
console.c isn't being provided. This adds a shim around the declaration
so that, like printk(), a call to vprintk() in this situation will expand
to a no-op function instead.
Change-Id: Ib4a9aa96a5b9dbb9b937ff45854bf6a407938b37
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
die() currently only accepts a fixed message string, which is rather
inconvenient when there is extra information that would be helpful to
print in the error message. This currently requires an extra call to
printk(), which is somewhat awkward:
printk(BIOS_EMERG, "Bad table, opcode %d at %d", id, i);
die(""); // what do I say here?
die() already has a printk() inside it to print the error message, so
let's just make it variadic to combine the two.
die("Bad table, opcode %d at %d", id, i); // much better
Forwarding variadic arguments from one function to another is rather
tricky, so die_with_post_code() is redefined as a variadic macro
instead.
Change-Id: I28b9eac32899a1aa89e086e0d3889b75459581aa
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Keith Short <keithshort@chromium.org>
This patch removes all possible dependencies in order to build platform
with CONFIG_RAMPAYLOAD enable(without ramstage).
A. Create coreboot separate stage kconfigs
This patch creates seperate stage configs as below
1. HAVE_BOOTBLOCK
2. HAVE_VERSTAGE
3. HAVE_ROMSTAGE
4. HAVE_POSTCAR
5. HAVE_RAMSTAGE
B. Also ensures below kconfigs are aligned with correct stage configs
1. COMPRESS_RAMSTAGE and RELOCATABLE_RAMSTAGE are now enable if
CONFIG_HAVE_RAMSTAGE is selected.
2. COMPRESS_BOOTBLOCK will enable if CONFIG_HAVE_BOOTBLOCK is set
3. COMPRESS_PRERAM_STAGES will enable if CONFIG_HAVE_VERSTAGE
|| CONFIG_HAVE_ROMSTAGE is selected.
C. Also fix compilation issue with !CONFIG_HAVE_RAMSTAGE
On x86 platform:
Case 1: ramstage do exist: CONFIG_HAVE_RAMSTAGE=1
>> rmodules_$(ARCH-ramstage-y) will evaluate as rmodules_x86_32
Case 2: ramstage doesn't exist: CONFIG_HAVE_RAMSTAGE=0
>> rmodules_$(ARCH-ramstage-y) will evaluate as rmodules_
This patch fixes Case 2 usecase where platform doesn't select
CONFIG_HAVE_RAMSTAGE.
Also add option to create sipi_vector.manual based on $(TARGET_STAGE)
variable.
$(TARGET_STAGE)=ramstage if user selects CONFIG_HAVE_RAMSTAGE
$(TARGET_STAGE)=postcar if user selects CONFIG_RAMPAYLOAD
Change-Id: I0f7e4174619016c5a54c28bedd52699df417a5b7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a method for the soc/amd/<product> to indicate what AcpiMmio
ranges are supported. Induce a build error if soc or mainboard
code is added which attempts to use an unsupported block.
This patch attempts to dissuade accessing unsupported blocks without
requiring the complexity of structures or reinitializing at the
beginning of a new stage.
TEST=boot grunt, force build errors by removing blocks in iomap.h
BUG=b:131682806
Change-Id: I2121df108fd3caf07e5588bc3201bcdd8dcaaa00
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
This patch adds support to read SPI flash in Dual SPI mode, where both
MISO and MOSI lines are used for output mode (specifically Fast Read
Dual Output (0x3b) where the command is still sent normally, not Fast
Read Dual I/O (0xbb) whose additional benefit should be extremely
marginal for our use cases but which would be more complicated to
implement). This feature needs to be supported by both the flash chip
and the controller, so we add a new dual_spi flag (and a new flags field
to hold it) to the spi_flash structure and a new optional xfer_dual()
function pointer to the spi_ctrlr structure. When both are provided,
Dual SPI mode is used automatically, otherwise things work as before.
This patch only adds the dual_spi flag exemplary to all Winbond and
Gigadevice chips, other vendors need to be added as needed.
Change-Id: Ic6808224c99af32b6c5c43054135c8f4c03c1feb
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
All SPI flash chip drivers currently in coreboot use the generic read
functions (spi_flash_cmd_read_fast()/_slow()) as their read callback.
The only use case for specialized read callbacks we have left is with
specialized flash controllers like Intel fast_spi (which sort of
impersonate the flash chip driver by implementing their own probe
function).
This patch unifies the behavior for all normal flash drivers by making
the read callback optional and letting them all fall back to a default
read implementation that handles normal fast/slow reading. Most of the
drivers used to install the respective callback after checking
CONFIG_SPI_FLASH_NO_FAST_READ, but some hardcoded either slow or fast
writes. I have found no indications for why this is and spot-checked
datasheets for affected vendors to make sure they all support both
commands, so I assume this is just some old inaccuracy rather than
important differences that need preserving. (Please yell if you
disagree.)
Also take the opportunity to refactor some of the common spi_flash.c
code a bit because I felt there are too many nested functions that don't
really do enough on their own, and centralizing stuff a bit should make
it easier to follow the code flow. (Some of this is in preparation for
the next patch.)
Change-Id: I2096a3ce619767b41b1b0c0c2b8e95b2bd90a419
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch changes the Gigadevice SPI flash driver to adopt the same
structure packing improvements for the hardcoded parameters of
individual chips that was implemented for Winbond last year. This cuts
the size of the hardcoded info nearly in half and should save us a few
hundred bytes in every stage.
Change-Id: I9910dcb9b649f51b317f3f8fcba49e5e893f67d2
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SPI transfer speed logging in cbfs_spi is super useful, doesn't get
in the way (just adding one line per stage, essentially) and should have
no notable overhead. Let's enable it by default for the BIOS_DEBUG log
level rather than having to recompile to get it.
Also fix an issue with building this code on MIPS due to lack of 64-bit
division primitives. (This means MIPS and arm32 board may display
incorrect results when reading more than 4MB in a single transfer, which
sounds very unlikely.)
Change-Id: I03c77938afe01fdcecf917e8c4c25cc29cdc764e
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The RAMPAYLOAD symbol added by 7e893a02c0 (Kconfig: Create RAMPAYLOAD
kconfig) is shown unconditionally for all x86 systems. It generally
creates a lot of confusion to prompt for something that isn't imple-
mented or not working. So guard it with another Kconfig that can be
selected by platforms that actually support it.
Change-Id: I6d158382d1000b8b40ca1368e2efff0c39884f15
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33263
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Select ONBOARD_VGA_IS_PRIMARY in driver/lenovo/hybrid_graphics to fix
disabling iGPU in 'Dual Graphics' on Lenovo T430.
* Remove ONBOARD_VGA_IS_PRIMARY in mainboards that already select
DRIVERS_LENOVO_HYBRID_GRAPHICS.
Change-Id: I6594fbb957c9a8135fe670d38b5755adf29d2dff
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
* Move the contents of iommu.c to early_init.c.
* Name the functions like done in intel/soc/common.
* Move PAMx register setup to own function
Preparations for integration in soc/intel/common/*
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I3ec395bf6722bceb84316e92733dcfcd7a093639
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32068
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the Return statement within the PS0, PS3 methods. PS0/3 are not
allowed to return anything. Even an empty return will be resolved to
Return(Null). In order to be conform with the specification, the code
has been refactored to remove the return statements.
Change-Id: I7b4820e8dd40a9169a7facce67282b8af5af67af
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33293
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of assuming GbE/PDR/EC regions may exist or not, check if there
is a valid region defined in the descriptor and set the region access
permissions based on that.
The net effect change is to enable the use of the PDR region on the
sarien platform, which also uses the GbE and EC regions.
This results in the following example changes:
mb/google/sarien (GbE, PDR, EC)
. DESC BIOS ME GbE PDR EC
-BIOS r rw rw r
-------------------------------
+BIOS r rw rw rw r
mb/google/eve: (no GbE, no PDR, no EC)
. DESC BIOS ME GbE PDR EC
-BIOS r rw rw r
-ME r rw r
-GbE r rw
-EC r rw
-------------------------------
+BIOS r rw
+ME r rw
+GbE
+EC
BUG=b:134703987
Change-Id: I7aeffc8f8194638c6012340b43aea8f8460d268a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33273
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds support for the UCSI specification in order to
provide information about the Type-C port and an interface to
perform power and data role swap.
This change is split across the DSDT and SSDT, with the shared
memory and operation region declared in the SSDT after being
allocated in CBMEM.
The OS will fill in the registers in the system memory region and
then call the _DSM method wtih a read or write argument. The DSM
method will copy the required registers to/from the system memory
and the EC and perform the write or read action.
Responses from the EC will generate a new SCI with event code 0x79
which will notify this UCSI ACPI device and the OS driver will take
action to read status from the EC.
BUG=b:131083691
Change-Id: I438a2bdfaf6720acd8354e0339dcef2844b63a4e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The USB Type-C Connector System Software Interface (UCSI) defines a
required memory oregion for the OS UCSI driver to use to communicate
with the BIOS and EC.
This provides a CBMEM ID that can be used by drivers to allocate this
shared memory region for the UCSI driver to use.
BUG=b:131083691
Change-Id: Id5b7fa19436443bc11a6ebe3ce89cd552cee4d85
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SD controller seems to take some time after restarting
the clock at 1.8V before it actually switches from 3.3V to
1.8V. Add a _DSM method that simply sleeps when switching
between 3.3V and 1.8V. Otherwise, the kernel times out too
quickly waiting for the card to acknowledge the 1.8V switch.
The card itself is waiting until it sees the clk signal being
driven at 1.8V.
BUG=b:125441242
TEST=Boot Hatch with SD card and CR2 removed, observe voltage
switch succeeds.
Change-Id: I15090ed9f9bc90b35dfcba47c913e3d37b799d0b
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Signef-off-by: Evan Green <evgreen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Logs from Linux' i915 suggest that not even the FSP/GOP takes proper
care of this. The sequence is mostly the same as on older platforms,
with a slightly different configuration of the backlight PWM.
We light the panel up with 50% PWM duty cycle. This often results in
an already rather high perceived brightness, but shouldn't be too
blinding.
Change-Id: I762a77c8df023a4c14af502af5edfeeb961da1ae
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Separate chipset-specific source from sata_init(), and modify it
to better match coreboot conventions. A subsequent patch will
move the generic portion to soc/amd/common.
The support for enabling port multipliers appears to have been
first added for Kabini. Although missing from the documentation,
the ability to affect the HBA Capabilities Register seems to remain
for Stoney Ridge.
Change-Id: I5dd9f613d36badc3e4d185a22b4475cb82ce187e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32660
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the function into common code. Convert it to use the memory-
mapped access type. Convert vboot_platform_is_resuming() to call it
instead of duplicating the source.
BUG=b:131682806
Change-Id: I245bebb8dc2d331cdd56acfb245a004536b792ab
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32658
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The halt.c file relies on the ACPI register block in the AcpiMmio
range. This register block is consistent across AMD device
generations, so to prepare for moving additional stoneyridge support
to this directory by changing the file name and add a Kconfig symbol
to control the build.
BUG=b:131682806
Change-Id: I2f7442dd78bced7f69b0416a8cd751291f82151f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32654
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The banked GPIO functionality in the AcpiMmio block has been consistent
since the Mullins product. Move the basic support into a common
directory.
Each product's pin availability, MUXes, and other details must remain
specific to the product.
The relocated source also drops the weak configure_gevent_smi() that
reports SMI is not available. The stoneyridge port relies on SMI
to do its initialization, similar to modern soc/intel devices. This
is the plan for future soc/amd ports, so make a missing function a
build error instead of a runtime warning.
BUG=b:131682806
Change-Id: I9cda00210a74de2bd1308ad43e2b867d24a67845
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch makes smm related files compile independent of
ramstage getting compiled.
If user selects RAMPAYLOAD to boot without ramstage, there
will be need for smm code to get compiled independently.
Change-Id: I17a3eb80a4d5ef86e0319357c01b6bf5b90ef15b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33115
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Documentation is scarce on the matter, however the related coreboot
code suggests that after the ACK, the keyboard also sends the result
of the self test (passed/failed). It looks like this result is never
consumed here, probably resulting in further confusion for later com-
mands.
Let's revert this for now (if it's not too late for the 4.10 release)
and break things later again. IMHO, due to the fact that there are
dozens of different keyboard controller and keyboard implementations
and no accurate specification followed, such changes should be tested
on a lot of hardware before merge.
This reverts commit a99ed13e33.
This reverts commit 7ae606f57f.
Change-Id: I4d4304d5d8a01e013feac61016c59bcaeea81140
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This automatically detects whether the southbridge supports AHCI.
If AHCI support is selected it will be used unless "sata_no_ahci" is
set in the devicetree to override the behavior.
Change-Id: I8d9f4e63ae8b2862c422938f3103c44e761bcda4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The RW_LEGACY section needs to be minimum 1M. For the 16MB BIOS
region, we had this region set too small, which was causing the
firmware_FMap FAFT test to fail.
BUG=b:133857135, b:129464811
BRANCH=None
TEST=test_that -b hatch <IP> firmware_FMap
Change-Id: Ie6311613ca3bb08e7f058a41d12f9a1153dc9c5e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Initial support for Facebook FBG-1701 system.
coreboot implementation based on Intel Strago mainboard.
Configure 'Onboard memory manufacturer' which must match HW.
BUG=N/A
TEST=booting SeaBIOS and Linux 4.15+ kernel on Facebook FBG-1701
Change-Id: I28ac78a630ee705b1e546031f024bfe7f952ab39
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
As long as we keep the IS_ENABLED() definition in libpayload for
compatibility, we should check that IS_ENABLED() usage doesn't
sneak back in.
Also remove all other IS_ENABLED() checks.
Change-Id: Id30ffa0089cec6c24fc3dbbb10a1be35f63b3d89
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The code in cpu/intel/car/romstage.c Does most of the things like
setting up timestamps, stack guards, entering postcar.
A functional difference is that the FSP header is searched for twice
instead of passed from the CAR entry to the C code. When using
C_ENVIRONMENT_BOOTBLOCK this needs to be done anyway (or a special
linker symbol kept across multiple stages is needed, which is likely
not worth the speedup).
Change-Id: I0f03e5a808f00157fdd807b104417a54e4bde7b2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
FDT property data should not be const -- sometimes we need to update it,
for example when fixing up phandles in an overlay. On the other hand
it's occasionally desirable to put a string constant in there without
having to strdup() it all the time... let's just live with the tiny
implicit assumption that the data we'd want to modify (phandle
references, mostly) will never be added from string constants, and put a
cast in dt_add_string_prop().
Change-Id: Ifac103fcff0520cc427ab9a2aa141c65e12507ac
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32868
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates the device tree dumping functions (not compiled by
default but available for debugging) to output properties and nodes in a
format similar to .dts files that is very close to what dtc outputs when
you decompile a .dtb with it. This makes it easier to match device tree
dumps from coreboot with device tree dumps generated by other device
tree tooling.
This patch was adapted from depthcharge's http://crosreview.com/1536386
Change-Id: Ib40e50d906aff05473a70c4fc9b124d63232558c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32867
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently DT paths are *not* expected to start with '/'. This is not
what the spec says (see Devicetree Specification v0.2, 2.2.3 Path Names)
and also not what is done by Linux.
Change dt_find_node_by_path() to expect paths to start with '/' and add
a leading '/' to all DT path strings. Besides the compatibility with the
spec this change is also needed to support aliases in the future.
This patch was adapted from depthcharge's http://crosreview.com/1252770
Change-Id: Ibdf59ccbb4ead38c6193b630642fd1f1e847dd89
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32865
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Besides looking up a node with an absolute path dt_find_node_by_path()
currently also supports finding a sub-node of a non-root node. All
callers of the function pass the root node though, so it seems there
is no real need for this functionality. Also it is planned to support
DT path names with aliases, which would become messy in combination with
the lookup from a sub-node.
Change the interface of dt_find_node_by_path() to receive the DT tree
object instead of a parent node and adapt all callers accordingly.
This patch was adapted from depthcharge's http://crosreview.com/1252769
Change-Id: Iff56be4da2461ae73a7301dcaa315758d2a8c999
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32864
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch caches phandles when unflattening the device tree, so we
don't have to look up the phandle property again every time we're trying
to find the phandle of a node. This is especially important when
supporting phandle lookups, which are also added. In addition we keep
track of the highest phandle in the whole tree, which will be important
for applying overlays later.
With this, dt_get_phandle(node) becomes obsolete because the phandle is
already available as a member variable in the node.
This patch was adapted from depthcharge's http://crosreview.com/1536385
Change-Id: I9cbd67d1d13e57c25d068b3db18bb75c709d7ebe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32863
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The FIT code is already using xzalloc() everywhere, and that's the only
real consumer of device tree code right now. Chances are if you're
trying to unflatten an FDT and it doesn't fit into the heap you're
pretty much screwed anyway, so all the OOM handling feels a bit
unnecessary (and some functions will just silently fail because they
don't have a return value, which is bad). Let's just switch this all to
die on failed allocations.
Change-Id: I738f24d550a776653b2becd3d4f7d4d2cb3cc048
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32861
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable LTR for NVMe and WiFi PCIe ports so that they can use ASPM L1.2
BUG=b:134195632
TEST=Verified L1 substate with lspci on hatch:
Before: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+
After: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
Change-Id: I7fce60897b78dde12747ac7fb857c988d16118ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33161
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:32951 ("libpayload: Reset PS/2 keyboard") added a call to reset
keyboard and check the return value of keyboard_cmd() to compare
against I8042_KBCMD_ACK. However, keyboard_cmd() already checks for
ACK and returns 1 or 0 based on whether ACK is received.
This change fixes the check introduced by CB:32951 to compare against
0 just like the other checks for keyboard_cmd(). Additionally, it adds
error messages for all failed commands in keyboard_init() to make the
prints consistent in case of failure.
BUG=b:134366527
TEST=Verified that logs do not contain "ERROR: Keyboard reset failed"
anymore.
Change-Id: Idcadaae12e0a44e404a1d98c6deb633d97058203
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch contains the general files for the vendorcode/eltan that has
been uploaded recently:
- Add eltan directory to vendorcode.
- Add documentation about the support in the vendorcode directories.
- Add the Makefile.inc and Kconfig for the vendorcode/eltan and
vendorcode/eltan/security.
BUG=N/A
TEST=Created verified binary and verify logging on Portwell PQ-M107
Change-Id: Ic1d5a21d40b6a31886777e8e9fe7b28c860f1a80
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
With the recent refactoring of memory configuration in
CB:32513 ("soc/intel/cannonlake: Support different SPD read type for
each slot"), meminit_cbfs_spd_index ends up reading SPD from CBFS for
each slot. However, for mainboards that use the same SPD index for
each slot this is unneccessary. This change adds a check to see if
spd_data_ptr is not NULL and current spd index is the same as the last
call to decide if SPD read from CBFS should be skipped.
TEST=Verified that SPD gets read only once on hatch.
Change-Id: I91963b55cea534c92207b2cd9f0caa96df8f222b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33137
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Re-add the Kconfig CONSOLE_UART_BASE_ADDRESS. It was lost by accident
on APL at least. It is used outside of soc/intel/ scope, e.g. to con-
figure SeaBIOS.
As we only ever configure a single UART for the coreboot console, we
don't need different addresses for each possible UART. Which saves
us a lot of code.
Change-Id: I28e1d98aa37a6acb57b98b8882fc4fa131d5d309
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This is never called: The only calling path is guarded by both
!DRIVERS_UART_8250MEM_32 and INTEL_LPSS_UART_FOR_CONSOLE but the
latter selects the former.
If somebody figures out how this is supposed to be used, we can
easily revive the implementation.
Change-Id: I96e304bdee4eadb52725027d0d662ef75f3d4307
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33093
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clang Static Analyzer version 8.0.0 detects access to field dev results
in a dereference of a null pointer which is loaded from variable bus.
Add sanity check for pointer bus to prevent null pointer dereference.
TEST=Built and boot up to kernel.
Change-Id: I084906c33065eaa834f50c545efcfab620658ec9
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
We should only provide this implementation when the Intel LPSS UART is
used. Otherwise, no other UART could be used for the console with these
SoCs.
Change-Id: Iebd89edb3f21d4a68587fd02659b4d529f3f4bbe
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
We only configure the base address for the console UART, the other
addresses are never assigned to the hardware. It seems better to
return 0 for them instead of a spurious value.
Change-Id: I3fa5c99958b56ca5b0b603917c086bdddb677fa2
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Instead of dereferencing a null pointer, print a nice message and exit
cleanly if the FSP isn't found in the CBFS.
Change-Id: I761e7febc7cec5bd2ef3af214bc51777ee5c313d
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1401467, 1401717
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33049
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This code to handle the brightness from SMM is copied from the Lenovo
Thinkpad X60 code, but does not work on later generation. The PCI
device it tries to address does not even exist on those devices.
Change-Id: Ia959eb5b747846048396e66d4c926c96c27f3878
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33138
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All Baytrail boards have the same GPU PCI ID, so set it
here to avoid having to set it in each board's config.
Move the VGA_BIOS_FILE config from google/rambi into soc/baytrail
since it likewise applies to all Baytrail boards.
Change-Id: Id1e0580b55e3590d868cb839987f06c49bb07cf5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33026
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Buddy's WLAN ACPI code was equivalent to, but formatted
differently from the other auron variants. Since only
differnce is root port used, have buddy use common
WLAN ACPI and use preprocessor guards to set the root
port correctly.
Test: build/boot Buddy, verify Windows 10 boots
without ACPI BIOS ERROR.
Change-Id: I78d994f2bb3981d4d10cb534cd6e0ae673f73527
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30523
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's no clear reason why most of coreboot's basic string functions
are static inline. These functions don't particularly benefit from
inlining (at least not notably more than other functions). This patch
moves them to string.c to be more consistent with our usual coding
practices.
Leaving the ctype functions as static inline because they actually seem
small and collapsible enough that inlining seems reasonable.
Also clarified the situation of strdup() and strconcat() a bit more,
optimized strrchr() to be single-pass, fixed a bug with using strchr()
to find '\0' and got rid of unnecessary register keywords.
Change-Id: I88166ba9876e94dfa3cfc06969c78a9e1bc6fc36
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
Create the Kindred variant of Hatch by taking a copy of the Hatch files
as placeholders. Kindred-specific changes will happen in future CLs.
BUG=b:133181366
BRANCH=NONE
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_KINDRED
Change-Id: I09ad3da0505d599fc3797d7fa24b4dc170dcd18b
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
gpio_pm_configure clears out all the bits related to PM configuration
in MISCCFG register and sets only the bits requested by mainboard. The
mask as it is set currently results in preserving all PM bits instead
of clearing them. This change updates the mask to ensure that the PM
bits are cleared before setting the ones requested by mainboard.
Change-Id: I5b8c04952775dc1e94fa229328be2f3c1102a468
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
These boards don't need a default FMAP. Moreover, having a default FMAP
disables automatic integration of optional regions like `CONSOLE`.
Also, these files contain an error: `COREBOOT` isn't placed at the top
of the image. Resulting in default builds without a reset vector ;)
Change-Id: If6331e19955034c02828e88902a5934c34d3e784
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33110
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Bootblock space is tight on this SoC and recent changes increased it
ever so slightly to make this a problem.
Since the bootblock is well-tested, we can get by without console.
Change-Id: I7496a3e313b2c6ee6fb3c4671eac64376d84e0dc
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33068
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix the following error from clang invoking gcc linker with wrong arg:
i386-elf-gcc: error: unrecognized command line option '--rtlib=libgcc';
did you mean '-static-libgcc'?
clang-4.0: error: linker (via gcc) command failed with exit code 1
Just remove --rtlib switch from CFLAGS relating to clang
Change-Id: Ife7ef6b6b47a04598fc67b40751bc59eed93b4af
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/21354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
In order to add the smbios_slot_desc for the SMBIOS Type9 entries into
the devicetree, and not use numbers but strings like
"SlotTypePciExpressGen3X4", smbios.h needs to be included in the
static.c.
Change-Id: Iace547868b4ce8eb7d3624baf1abd1187c1e5f51
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32965
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add two new options:
* Disable the prompt "Press Ctrl+B for the iPXE command line..."
Add a boolean that disables the initial 2 second timeout.
* Include a script that is executed instead of showing a shell.
Allows to add a script that will be included into the iPXE ROM.
Tested on Lenovo T500 and PC Engines apu2.
Change-Id: Ie1083d8571d9d1f1c7c71659fb6ff0de2eecad0e
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/20782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The initialization logic for the fixed_msrs and msr_index arrays depends
on the contents of the fixed MTRR descriptor. However, Coverity is unable
to check these values and believes (incorrectly) that the arrays may not
be entirely initialized. An assert was added in commit b28025a434 to
ensure that one of the loops is entered, but it is simplest to just
check that msr_num has iterated over the entire array after the loops
are over. This also acts as a sanity check that the values in the MTRR
descriptor were hardcoded correctly.
Change-Id: Ia573792f74aa6ea5e659c1e2253f112184fbb0a5
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1370582
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
It is possible that acpi_device_scope() and acpi_device_name() can
return NULL to indicate an error, so add error handling to check their
return values.
Change-Id: I4c7ab0c592845d9d5f142e078fc2b505a99ecd12
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1362592
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
When clapper was upstreamed, the devicetree was pulled from
the wrong firmware branch, leading to some incorrect settings
and touchpad, touchscreen, and audio not working.
Correct devicetree settings using Chromium branch firmware-clapper-5216.199.B
Test: build/boot google/clapper, verify touchpad/touchscreen/audio
functional under Linux (GalliumOS 3.0/kernel 4.16.18).
Change-Id: Iacfce575a054b1f484149f36d0aa83d20d034d8a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Legacy Google mainboards (pre-Skylake) shipped with the
SMBIOS manufacturer set to GOOGLE, which many Linux drivers
rely on for application of DMI quirks. Set it as the default
to avoid having to do so for each board's config
Change-Id: I61b0217f3535852d7d6e24a1ac78075c20c0825a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Clang Static Analyzer found version 8.0.0 gnvs is allocated, but
it is never used. Change sizeof(*gnvs) to sizeof(global_nvs_t)
while adding ACPI GNVS to CBMEM.
TEST=Built and boot up to kernel.
Change-Id: Ie9421af4a556d1d88183aa938ee2a124a10ab727
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Clang Static Analyzer version 8.0.0 detects that log2_ceil(bios_size)
and log2_ceil(window_size) are garbage or undefined if the value of
bios_size and window_size is zero. Check bios_size and window_size after
MIN operation to prevent error.
TEST=Built and boot up to kernel.
Change-Id: Ifc3f3da52d129ef5d6063a46b045603a236be759
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Clang Static Analyzer version 8.0.0 detects the division by zero if
gspi_clk_mhz is initialized to 0. gspi_clk_mhz is referred to speed_mhz
in devicetree. Set gspi_clk_mhz to 1 if it is detected as 0 in order to
prevent the division by zero in DIV_ROUND_UP operation. Then the value
of (ref_clk_mhz - 1) will be fed into GSPI's Serial Clock Rate value.
TEST=Built and boot up to kernel.
Change-Id: I6a09474bff114c57d7a9c4c232bb636ff287e4d5
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
inteltool can't detect whether address mapping is normal or
mirrored, which in turn may be cause RAM initialization to
fail when using spd.bin generated by inteltool.
Mention this in readme as it may help someone.
Change-Id: I8d24e4d9332bdcf484987581dd6941e2bf9c4f87
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
When using native raminit with https://review.coreboot.org/#/c/22683/
I've found that timC training usually fails unless the ram is
overspecced (i.e. DDR3L-1600 rated for 1.35V works most of the time with
native raminit as DDR3-1333 @1.5V).
Looking at the training data I've found that during timC training it is
reading register values in the 0-4000 range and checking for runs of 0,
but with the failing training the values don't go all the way down to 0.
The solution for me has been to do a thresholing pre-pass, after which
both the DDR3-1333 @1.5V and the DDR3L-1600 @1.35V work fine for me.
Tested:
- Intel NUC DCP847SKE
- RAM slots with 2x4GB Kingston KVR1333D3S9/4G (DDR3-1333 1.5V),
boots fine with native raminit @1.5V
- RAM slots with 2x4GB Kingston KVR16LS11/4G (DDR3L-1600 1.35V),
boots fine with native raminit @1.35V
- Casual use with these settings
- Tested on Lenovo T520 with Crucial HyperX DDR3-1833.
- Memtest86+ stable.
Change-Id: I9986616e86560c4980ccd8e3e549af53caa15c71
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/22776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The Gigabyte GA-B75M-D3H/D3V mainboard trees share a lot of duplicate
code, and can serve as a base for porting other Gigabyte 7 series
motherboards. Switch the Gigabyte GA-B75M-D3H/D3V mainboard trees to a
variant setup, defining ga-b75m-d3v as a variant of ga-b75m-d3h.
Signed-off-by: Alex James <theracermaster@gmail.com>
Change-Id: Ia175207a2568aefe1aa9bd8d4d990de6a26f1657
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
It doesn't make sense to add a property to a non-existent Device
Property package. However, some of these functions will proceed anyway
and allocate a new Device Property package, add the property to
that, and then immediately leak the new package. This changes all the
acpi_dp_add_* functions to ignore a null package.
Change-Id: I664dcdbaa6b1b8a3aeb9a0126d622e2ffb736efd
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 135745{6,7}, 138029{2-6}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
For x64 and x86_32 configurations, apply the -march flag to both GCC and
Clang flags.
This solves the problem of Clang-compiled coreboot failing due to Clang
emitting SSE instructions for code that is executed while SSE is not
enabled.
This patch takes functionality targeted for GCC configurations and moves
it down a few lines, modifying CFLAGS instead of GCC_CFLAGS in order
that it applies to both GCC and Clang.
This is an alternate patch to CB:32887.
Signed-off-by: Alan Green <avg@google.com>
Change-Id: I6a6a6136b01a64d46f730ed19ebbeaadaf2183df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Dumping ME status displays wrong information if we disable Heci1 because
it is called after fsp notifies EndOfFirmware and disables Heci1. This patch
moves the ME status dump before fsp notify EndOfFirmware.
TEST=Boot to OS, check ME dump information
Change-Id: Ifd8b18a41c502c4ecfb84698a7669028394589fd
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
TSEG is not accessible in ring 0 after it is locked in ramstage, in
contrast with cbmem which remains accessible. Assuming SMM does not
touch the cache this is a good region to cache stages.
Change-Id: I89cbfb6ece62f554ac676fe686115e841d2c1e40
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This list is incorrect and not up to date. The FSP1.1 romstage
bootflow is unnecessarily clumsy and instead of trying to update this
comment effort is better spend making the bootflow more streamlined.
Change-Id: If1e4c462acd0748f072f33e6397a7b43f3bfc834
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Loading a libpayload based payload like coreinfo or FILO from SeaBIOS or
GRUB pressing keys does not give the expected results.
For example, pressing F1 gives the character 24 translated to scan code
6a. ESC for example 43 (111) in coreinfo loaded from SeaBIOS on QEMU
Q35.
The problem is not reproducible using the payload directly, that means
without SeaBIOS or GRUB. The problem seems to be, that those have already
initialized the PS/2 controller and AT keyboard.
Comparing it with coreboot’s PS/2 keyboard code, the keyboard needs to
be reset. That seems to fix the issue, when the keyboard was initialized
before.
TEST=Build coreboot for QEMU Q35 with SeaBIOS, and coreinfo as secondary
payload. Run
qemu-system-i386 -M q35 -L /dev/shm -bios build/coreboot.rom -serial stdio
press 3 to select the coreinfo payload, and verify that the keys F1 and
F2 are working.
Same with coreinfo loaded from GRUB on the ASRock E350M1.
Change-Id: I2732292ac316d4bc0029ecb5c95fa7d1e7d68947
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This adds a file i82801gx/bootblock_gcc.c since other targets that
don't yet C_ENVIRONMENT_BOOTBLOCK still use the romcc compiled
bootblock.c.
Tested on Foxconn D41S.
Change-Id: I7e74838b0d5e9c192082084cfd9821996f0e4c50
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Unify thermal handling across Lenovo boards (except g505, which is
different). Namely, do the following:
* Move thermal levels from acpi_tables to thermal.h (and create if
necessary).
* Don't use board-specific ifdef guards.
* Set thermal levels using dedicated acpi_update_thermal_table function
as almost all Lenovo boards do.
* Update list of authors in comments. Merge all author's entries.
* Minor whitespace and formatting.
This makes diff -ruw between the Lenovo boards smaller.
Change-Id: If569f67c932b7fbf14893b890a5588df4994daeb
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29659
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Pass the return value from early_mmc_wake_hw() to the payload so that
payload can skip sending CMD0 and resetting the card in case of success
or in case of a failure in firmware, payload can recover by sending
CMD0 and resetting the card.
BUG=b:78106689
TEST=Boot to OS
Change-Id: Ia4c57d05433c3966118c3642913d7017958cce55
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25464
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to improve boot time with emmc, add ability to send CMD0
and CMD1 early in romstage. This way, by the time system boots to
payload, we are ready to continue with emmc setup and we don't need
to send CMD0 in payload again, and wait for card to reset and be ready.
BUG=b:78106689
TESTS = Boot to OS
Force early_mmc_wake_hw() to return error, recover in payload
Force an error in payload, make sure system can recover/boot
Change-Id: I3488b077bf5100a1e0f2c879fb1436105607d25e
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
It is possible that 'lnode->val' is set to 0 on a previous iteration of
the loop, so check that it is non-null here before dereferencing it.
Change-Id: I9827dd5623eaf11240df605a8b50ff9e27a5fce0
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1129149
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The 'new_type' function already allocates memory, so it is only
necessary to clone the existing type if this function is not called.
Change-Id: I47065204c5f4b6bab022bd7ccf19838c3ce1f86e
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity Scan CID 1129106
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
It is possible that 'filename' is still null in this if statement,
so we add an extra check to prevent a null dereference in strcmp.
Change-Id: Iaba95b63a4d552051e0c56445522de7274dfd0b3
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1395330
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
In each of these cases it is possible that 'member' is NULL at the
beginning, which will skip the earlier while loops entirely and cause
a NULL dereference later on. Add extra error checks to prevent this.
Change-Id: Ib5873c0830b71397ef661976d387fc6ce33c5cd1
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1129147, 1129152, 1129153, 1129154
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
CMOS isn't used that early, but the chipset initialization may be
required to access it.
In one instance, Intel Apollo Lake, the sanitize_cmos() function
seems to hang if called before bootblock_soc_early_init(). The
missing step is fast_spi_early_init(). But even without, one might
expect sanitize_cmos() to return eventually (it didn't within
about 20min).
Change-Id: I6e1a029e4be7e109be43a3dad944bd7e05ea1f02
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
In some cases we may have boards that need to differentiate SKUs but
don't really want to differentiate revisions (at least for some SKUs).
Let's add a compatible string match that includes only the SKU but not
the revision so that kernel DTSes don't have to specify every possible
revision if they want to match this.
This patch was adapted from depthcharge's http://crosreview.com/1512004
Change-Id: Ib88862424b350a213761f5662fe170a1f8fccc7f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32859
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
vtxprintf.c seems to have been written before string.h was as fleshed
out as it is today -- this patch removes some custom implementation of
stuff we now have globally. It also makes the skip_atoi() function
globally available, because I need it somewhere else, and while we maybe
don't want a huge fully-featured string parsing library in coreboot,
being able to parse an integer is occasionally useful.
Change-Id: Iecb2b970aecfc768540d2bf8b3023445f54853a4
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
coreboot should not have a definition of printf() anywhere -- it's too
easy to accidentally sneak it into code otherwise. Where that is needed
in code shared with userspace utilities, we should instead use printk()
and define a shim for that for the userspace side.
Change-Id: Iaa459df7122c88beb56695eee7c252d90bbde861
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32857
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Libpayload has a family of functions that can "encode" or "decode" an
endian-specific integer onto a byte stream pointer. These allow writing
more pretty code than a raw be32_to_cpu/cpu_to_be32 with pointer casts
in many (de-)serialization scenarios, so let's add them to coreboot as
well.
Change-Id: I049c5665484da12b3cf977a529310b0bde177d2d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32856
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On Wilco devices, if any of the coreboot stages fails with a fatal
error, set the diagnostic LEDs with the Wilco EC. The last saved
post code is used to determine the error code sent to the EC.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
TEST=Remove DIMM module, confirm diagnostic LED pattern for memory
failure (2 amber, 4 white).
TEST=Forced a fatal error in both bootblock and verstage to confirm
diagnostic LEDs during these stages. This works on cold-boots only. Bug
b:132622888 tracks the mailbox failures on warm boots.
Change-Id: If865ab8203f89e499130f4677fec166b40d80174
Signed-off-by: Keith Short <keithshort@chromium.org>
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add a new post code POST_VIDEO_FAILURE used when the Intel FSP silicon
initialization returns an error when graphics was also initialized.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
Change-Id: Ibc7f7defbed34038f445949010a37c8e368aae20
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add a new post code POST_HW_INIT_FAILURE, used when coreboot fails to
detect or initialize a required hardware component.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
Change-Id: I73820d24b3e1c269d9d446a78ef4f97e167e3552
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add a new post code POST_RAM_FAILURE, used when the Intel FSP code fails
to initialize RAM.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
Change-Id: Ibafefa0fc0b1c525f923929cc91731fbcc1e7533
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add a new post code POST_INVALID_VENDOR_BINARY, used when coreboot fails
to locate or validate a vendor supplied binary.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
Change-Id: Ib1e359d4e8772c37922b1b779135e58c73bff6b4
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add a new post code POST_INVALID_CBFS, used when coreboot fails to
locate or validate a resource that is stored in CBFS.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
Change-Id: If1c8b92889040f9acd6250f847db02626809a987
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add a new post code, POST_INVALID_ROM, used when coreboot fails to
locate or validate a resource that is stored in ROM.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
Change-Id: Ie6de6590595d8fcdc57ad156237fffa03d5ead38
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Works:
- bootblock, romstage, ramstage
- Serial console UART0, UART1
- SPI flash console
- iGPU init with libgfxinit
- LAN1, LAN2
- USB2, USB3
- HDMI, DisplayPort
- eMMC
- flashing with flashrom externally
WIP:
- Documentation
- VGA
For some reason Seabios can not find the CBFS region
and therefore it can't load seavgabios, but generally
it is working as soon as Linux is booted.
- ACPI
Works not:
- Devices needs proper configuration
- Seabios can't find CBFS region
Untested:
- GPIO pin header
- 60 pin EXHAT
- Camera interface
- MIPI-CSI2 2-lane (2MP)
- MIPI-CSI2 4-lane (8MP)
- SATA3
- USB3 OTG
- embedded DisplayPort
- M.2 slot
- mini PCIe
- flashing with flashrom internally using Linux
Change-Id: Ia913534ec176fc600fcd4ce3af335ebe682b0ed4
Signed-off-by: Felix Singer <felix.singer@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Enabling flashconsole on these platforms fails to build due to
spi.c not being compiled in prior to ramstage. Include in early stages
(bootblock/romstage/postcar) as needed to enable flashconsole support.
Early inclusion of monotonic_timer.c is needed for Broadwell as well.
Change-Id: Idae0578ca92939246021bb85e34b0dcbd41df3b5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
If 'class > LAST_REGC', then there will be an out-of-bounds read when
accessing 'regcm_bound'. Prevent this by skipping to the next iteration
of the loop. Note that this should not generally happen anyway, since
'result' represents a bitset for the indices of 'regcm_bound', and so
iterations where 'class > LAST_REGC' should already be skipped by the
previous continue statement (since those bits of 'result' should all be
zero).
Found-by: Covericy CID 1129122
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: Id5f5adb0a292763251054aeecf2a5b87a11297b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This moves FSP1.1 to use postcar stage to tear down CAR.
On platforms with USE_GENERIC_FSP_CAR_INC the FSP header is found
during the postcar stage so there is no need to push to save it
in CAR global variables.
On FSP1.1 platforms with an open source CAR implementation (Skylake,
even though it still runs the FSP-T), the
soc/intel/common/blocks/cpu/car/exit_car.S code tears down CAR.
This also uses common functions to set up the MTRR to use after
CAR is torn down.
Test: build/boot on google/celes (BSW) and google/chell (SKL)
Change-Id: I2330993842aae9c1365230f0c6bd8a2449dc73a5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
This patch removes redundant mca_configure() function call
from ramstage to clear machine check exception. First time it's
getting called from soc_core_init() function inside cpu.c file.
TEST=Build and boot SKL/KBL/AML platform without any machine-check
exception.
Change-Id: I7e54fd07816c6317588ab6db06365937c4300ccd
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
The corner case of an empty string literal was causing romcc to
segfault. This checks if the literal is empty, and if so allocates a
size one buffer for the terminating null character. A test case for
this is added to ensure it doesn't happen again.
Found-by: Coverity CID 1129099
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I067160a3b9998184f44e4878ef6269f372fe68bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
'used_indices' is 64 bits wide, so use a fixed-width type to make
that clear. As such, 'index' can have a value of up to 63, so use a
64 bit integer when doing the shifts to prevent overflow.
Found-by: Coverity Scan CID 1287090
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: Ibd089df6be60c8ea46da11e5e83cd58b2e2c54d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32854
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested:
- Ethernet NIC
- Wifi RFKill
- USB
- LVDS, VGA with libgfxinit
- Booting with dock attached (COM1)
- Keyboard, trackpoint
- SeaBIOS 1.12
- S3 resume
- Tested in descriptor mode, with vendor FD and ME
- Add VBT to ACPI OPregion
Untested:
- SATA (likely works)
- Trackpad (my cable is broken, likely works)
- Displayport (likely works)
- Descriptorless mode
- DVD drive
- Extra battery
- model with ATI GPU
Does not work:
- Dock hotplug
- Quad core CPU (hangs during AP init, probably needs hardware mod)
- Hotplugging the expresscard slot (works with 'echo 1 | sudo tee
/sys/bus/pci/rescan')
TODO:
- proper dock support
- documentation
note: This board was hard to flash, I had to desolder the flash.
TESTED: on a R500 with an Intel iGPU, SeaBIOS 1.12, Debian 9,
Linux 4.9 from USB
Change-Id: I9e129b2e916acdf2b8534fa9d8d2cfc8f64f5815
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
When FSP UPD parameters are configured, also configure the GSPI CS lines
appropriately. GSPI driver assumes CS0 is the CS signal to use.
BUG=b:130329260
BRANCH=None
TEST=Boot Kohaku, TPM communcation still functional.
Change-Id: Ic816395b7d198a52c704e6cabcb56889150b741c
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32791
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This microcode update for CPU IDs 0x610F01/0x610F31 improves system stability:
in particular, fixes Xen hardware virtualization freezes. Also it attempts to
patch some Spectre-related security vulnerabilities. This new microcode has been
tested by multiple coreboot community members and found working perfectly.
Old version: 0x600110F [2012-01-11]
replaced by
New version: 0x600111F [2018-03-05]
Change-Id: Ied5da0ff85abb63c2db2eeafd051b8e00916d961
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28273
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: <awokd@danwin1210.me>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This microcode update for CPU ID 0x700F01 improves system stability:
in particular, fixes Xen hardware virtualization freezes. Also it attempts to
patch some Spectre-related security vulnerabilities. This new microcode has been
tested by multiple coreboot community members and found working perfectly.
Old version: 0x700010B [2013-07-09]
replaced by
New version: 0x7000110 [2018-02-09]
Change-Id: Iebe6e54d922378a8a1feb97f37b08ac50c8234b2
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28370
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
sarien/arcada:
GPIO_COMM_0/2/3/4: Enable gpio community all PM configuration
GPIO_COMM_1: Disable RCOMP clock gating due to GPP_D18 IRQ mapped for H1 TPM.
hatch:
GPIO_COMM_0/1/2/3: Enable gpio community all PM configuration
GPIO_COMM_4: Disable RCOMP clock gating due to GPP_C21 IRQ mapped for H1 TPM.
BUG=b:130764684
TEST=H1 TPM interrupt working find and able to boot from fixed boot media
Change-Id: Ia4d5483847a4d243b9038119d4bb5990591cc754
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
GPIO_COMM_0/2/3/4: Enable gpio community all PM configuration.
GPIO_COMM_1: Disable RCOMP clock gating due to GPP_D16 IRQ mapped for H1 TPM.
BUG=b:130764684
TEST=H1 TPM interrupt working find and able to boot from fixed boot media
Change-Id: I1f83f938f201c6574367960b1027555767cf6f3d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Adds support for the KB_ERR_CODE command on the Wilco EC. This command
is used to drive diagnostic LEDs on the platform after a failed boot.
This change also adds the Wilco EC mailbox command support to bootblock
and verstage so that those stages can use the KB_ERR_CODE command.
BUG=b:124401932
BRANCH=sarien
TEST=build coreboot for sarien and arcada platforms
Change-Id: I96d17baf57694e4e01c676d80c606f67054cd0c3
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32776
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Apply commit d7b88dcb (mb/google/x86-boards: Get rid of power button
device in coreboot) to AMD Brazos boards [1]:
> As per the ACPI specification, there are two types of power button
> devices:
> 1. Fixed hardware power button
> 2. Generic hardware power button
>
> Fixed hardware power button is added by the OSPM if POWER_BUTTON flag
> is not set in FADT by the BIOS. This device has its programming model
> in PM1x_EVT_BLK. All ACPI compliant OSes are expected to add this
> power button device by default if the power button FADT flag is not
> set.
>
> On the other hand, generic hardware power button can be used by
> platforms if fixed register space cannot be used for the power button
> device. In order to support this, power button device object with HID
> PNP0C0C is expected to be added to ACPI tables. Additionally,
> POWER_BUTTON flag should be set to indicate the presence of control
> method for power button.
[..]
> This change gets rid of the generic hardware power button from all
> google mainboards and relies completely on the fixed hardware power
> button.
The same problem exists with the AMD Hudson devices in coreboot.
For AMD Hudson (2) and Yangtze based devices this was removed in commit
44f2fab8 (AMD hudson and yangtze boards: Let mainboard declare power
button) [2].
Two devices are detected.
$ dmesg | grep Button
[ 0.209213] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.209254] ACPI: Power Button [PWRB]
[ 0.209332] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.209349] ACPI: Power Button [PWRF]
$ sudo evtest
No device specified, trying to scan all of /dev/input/event*
Available devices:
/dev/input/event0: Power Button
/dev/input/event1: Power Button
[..]
[1]: https://review.coreboot.org/5546
[2]: https://review.coreboot.org/27272
Change-Id: I0cbecb72f7e1bf3d051d3b7656c6af4d6f43b497
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/27496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The system should boot fine to OS on pressing power button before the
system enters G3. However, on hatch, we observe that the system waits
for few seconds at "Starting kernel" and then resets, with SD card tray
inserted and SD_CD# pad reset config set to DEEP. Hence configuring SD_CD#
pad reset config to PLTRST.
BUG=b:129933011
TEST=Built and verified on hatch.
Change-Id: Ic4466b96332f095ff39b28d98607e95fc3d12d6a
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
cbmem_find is not available in every stage.
Remove usage of cbmem_find() and use GEN_PMCON1 always.
BUG=NA
TEST=Booting Embedded Linux on Facebook FBG-1701
Change-Id: Id97d57864b3e241e8f046d9b1caebdce199a46b1
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
vboot_measure_cbfs_hook() is included when CONFIG_VBOOT_MEASURED_BOOT
is enabled, but this function is defined as 0 in vboot_crtm.h using ENV_
Remove ENV_ for vboot_measure_cbfs_hook() function definition.
This function is added to bootblock stage also.
BUG=NA
TEST=Build Google Banon and Google Cyan
Change-Id: Ic62c18db09c119dfb85340a6b7f36bfd148aaa45
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Save whether or not vboot has selected developer mode as a flag
in vboot_working_data. Other coreboot code may access this flag
without needing to consult vboot_handoff (which is in the process
of being deprecated).
BUG=b:124141368, b:124192753
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ieb6ac4937c943aea78ddc762595a05387d2b8114
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
With CB:32726 ("lib/timestamp: Make timestamp_sync_cache_to_cbmem() in
postcar") timestamps are synced from cache to cbmem in postcar as
well. For postcar, the cache lives in BSS just like ramstage. This
change updates TIMESTAMP_CACHE_IN_BSS to include both ramstage and
postcar and uses this instead of ENV_RAMSTAGE to check for cache
location.
Ideally, it would be good to get rid of timestamp cache in postcar and
ramstage completely since early cbmem init is enabled by default in
coreboot and it is guaranteed that cbmem is recovered before
timestamps are added in ramstage or postcar. This change is being
pushed in as a temporary fix while I make the changes to remove
timestamp cache from romstage and postcar completely.
BUG=b:132939309
Change-Id: I2d82a96aba954df77c9386b7bd2e2ec0973881be
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
The VPD field name is dock_passthrough, not dock_passthru. Fix it.
(I assume there is no length limit)
BUG=b:132689337
TEST=check that the feature can now be controlled by the associated
enterprise policy
Change-Id: Icc2b070313fde74447279cd6ccaa4e3eb6d119ee
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32839
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fill the DIMM serial number field for SMBIOS from the saved SPD
data that is returned by FSP.
BUG=b:132970635
TEST=This was tested on sarien to ensure that SMBIOS type 17
filled the serial number from the DIMM:
Handle 0x000B, DMI type 17, 40 bytes
Memory Device
Locator: DIMM-A
Serial Number: 41164beb
Change-Id: I85438bd1d581095ea3482dcf077a7f3389f1cd47
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Set the system serial number from the VPD key "serial_number" and
the mainboard serial number from the VPD key "mlb_serial_number".
BUG=b:132970635
TEST=check serial number is set in SMBIOS based on VPD, and if there
is no VPD key found then it is empty.
Change-Id: Ia8f1486dcb1edc968b8eb1e6d989b10c05913aca
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Clang does not recognize dead_code() as termination of execution. It
gives this message:
error: control reaches end of non-void function
[-Werror,-Wreturn-type]
This change adds an __attribute__((noreturn)) to ensure that clang
recognises that this function will terminate execution.
This change is more general solution to the problem that was addressed
in the specific at https://review.coreboot.org/c/coreboot/+/32798
Signed-off-by: Alan Green <avg@google.com>
Change-Id: I5ba7189559aa01545d5bbe893bced400a3aaabbb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Move the DMI initialization code to northbridge folder.
Leave southbridge specific settings in bd82x6x folder and call it from
northbridge code.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: Ib0b47391f3309f9ab0c3a3a8d525f38f8cca73c0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add a few comments and use known register values.
Based on the "2nd Generation Intel® Core™ Processor Family Mobile"
datasheet and the existing serialice trace.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to GNU/Linux.
Change-Id: I404515b77a22324f55581f117d79630be4ba64dd
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32071
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Enable LPC TPM support in Kconfig and add pc80/tpm to devicetree
- Enable VBT support in Kconfig and add VBT files extracted from
vendor firmware
- Remove IGPU VBIOS entries from Kconfig
- Remove unused PS2 definitions in superio.asl
- Add PWRB ACPI device entry to mainboard.asl
- Remove duplicate chipset register initialization from mainboard.c
- Move ITE Super I/O configuration to mainboard_config_superio in
romstage.c
Signed-off-by: Alex James <theracermaster@gmail.com>
Change-Id: I2d11c55dc809b920bccf55f5f745d9f29b18bbb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Previously cpu_index() always succeeded, but since commit 095c931
(src/arch/x86: Use core apic id to get cpu_index()) it is now possible
for it to indicate an error by returning -1. This commit adds error
handling for all calls to cpu_index(), and restores several checks that
were removed in commit 7c712bb (Fix code that would trip -Wtype-limits)
but are now needed.
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I5436eed4cb5675f916924eb9670db04592a8b927
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- The link to create an account is now "Sign in" and not "Register"
- Use monospace formatting for terminal commands and file names
- Properly escape less-than and greater-than
- Correct the 'make lint' example command
- Reformat example commit messages
- Add formatting for website links
- Other whitespace fixes
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I9931bef8c30387d1c08b59973d6de9b5c0419814
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The FSP will lock down the configuration of GPP_A12, which
makes the configuration of the GPIO pin on warm reset not
work correctly.
This is only needed for the Arcada variant since it is the only variant
that uses ISH.
BRANCH=sarien
BUG=b:132719369
TEST=ISH_GP6 now works on warm resets on arcarda
Change-Id: Icb3bae2c48eee053189f1a878f5975c6afe51c71
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32831
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the stoneyridge AcpiMmio code into soc/amd/common.
The SB800 southbridge introduced the MMIO hardware blocks at 0xfed80000
commonly known as AcpiMmio. Implementations beginning with Mullins
enable decode in PMx04. Older designs use PMx24 and allow for
configuring the base address. Future work may support the older version.
Comparing the documentation for AMD's RRGs and BKDGs, it is evident that
the block locations have not been reassigned across products. In some
cases, address locations are deprecated and new ones consumed, e.g. the
early GPIO blocks were simpler at offset 0x100 and the newer GPIO banks
are now at 0x1500, 0x1600, and 0x1700.
Note: Do not infer the definitions within the hardware blocks are
consistent across family/model products.
BUG=b:131682806
Change-Id: I083b6339cd29e72289e63c9331a815c46d71600d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32649
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previously broadwell used a romcc bootblock and starting verstage in
romstage was madatory but with C_ENVIRONMENT_BOOTBLOCK it is also
possible to have a separate verstage.
This selects using a separate verstage by default but still keeps the
option around to use verstage in romstage.
With a separate verstage the romstage becomes an RW stage.
The mrc.bin however is only added to the RO COREBOOT fmap region as it
requires to be run at a specific offset. This means that coreboot will
have to jump from a RW region to the RO region for that binary and
back to that RW region after that binary is done initializing the
memory.
Change-Id: I900233cadb3c76da329fb98f93917570e633365f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30384
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This puts the cache-as-ram init in the bootblock.
Before setting up cache as ram the microcode updates are applied.
This removes the possibility for a normal/fallback setup although
implementing this should be quite easy.
Setting up LPC in the bootblock to output console on SuperIOs is not
done in this patch, therefore BOOTBLOCK_CONSOLE is not yet selected.
Change-Id: I44eb6d380dea5b82e3f009a46381a0f611bb7935
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Free several resources when AHCI initialization fails. Note that it is
only safe to free resources when the command engine has stopped, since
otherwise they may still be used for DMA.
Found-by: Coverity CID 1260719, 1260727, 1261090, 1261098
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I6826d79338b26ff9696ab6ac9eb4c59f734687d8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
As of CL:1605641, vboot2 code should be used for setting and
checking display init state. Remove all vboot1 OPROM-related
code, and use the vboot2 display init code which has already
been added in previous commits.
coreboot should not be reading vboot NVRAM flags directly.
Remove the function vboot_wants_oprom(), and instead rely on
display_init_required(), which uses the
VBOOT_WD_FLAG_DISPLAY_INIT value stored in
vboot_working_data.flags, initialized during verstage.
Note that this means in the case of CONFIG_VBOOT=y, the return
value of display_init_required() can only be trusted after
verstage has been executed. This should not be a problem
assuming that all display initialization occurs in ramstage.
BUG=b:124141368, b:124192753, chromium:948529
TEST=Build locally
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ic8f9dc5a3c7f1546a8fed82bde02be4d04568f8d
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:1605641, chromium:1605525
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32723
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Verified Boot OPROM code is being refactored. OPROM is being
generalized into "display initialization". As such, the NVRAM
request flag is being renamed from OPROM_NEEDED to
DISPLAY_REQUEST.
BUG=b:124141368, b:124192753, chromium:948529
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I74374abf7d1deb594c073f7a4a76c9de46092143
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:1605640
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
We need to support entering D3Cold from the OS to work around a bug in
the SDHC where the data lines get stuck always reading zeros.
BUG=b:122749418
TEST=Verified the linux kernel can transition between D3 and D0. Also
verified that the device can suspend and resume and continue to have a
functioning SD controller after.
Change-Id: Ifbf48f20c03a752ce3ff773296b536e92db16a62
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch adds a workaround for Samsung C-die 2G/4G memory chips.
For unknown reasons, some boards with Samsung LP3 memory chips
could not pass early CS/CMD training. MRC has to change the
granularity from 16 ticks to 8 ticks, which implies bad margin
with this memory chip. Another way is to enhance the drive
strength for CS. This patch is to enhance the drive strength for CS
and CMD. Enhancing the drive strength for CMD could gain margin abaout
3 more ticks. Root cause needs to be further investigated with memory
vendor.
BUG=b:131177542
BRANCH=None
TEST=USE=fw_debug emerge-atlas chromeos-mrc coreboot chromeos-bootimage
& check the MRC log to ensure correct Rcomp values are passed to
MRC. Tested with board ID #8 and #11.
Change-Id: I9ea3ceda8dc8bf781063d3c16c7c2d9b44e5ddd6
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
* Add more chip register to move PEI data to devicetree.cb.
* Set northbridge/southbridge and runtime detectable settings.
* Fill in values from devicetree.
This change is still a noop as the pei structure is completely overwritten
with the exsting mainboard pei structure.
The followup commit will migrate to devicetree.cb.
Tested on Lenovo T520, boots MRC path with the new devicetree settings.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Change-Id: Ic6d9f0fd6a2b792ac693d6016ed9ce44945c900c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Move the onboard SPD to second channel as native raminit does and workaround
mrc expecations in northbridge code.
Required to move pei data to devicetree and to use the same code for mrc and
native raminit.
Tested on Lenovo T520:
Other fields then spd_data[0] are ignored.
Change-Id: If1910e82a4bd178c2a6c2991c91e09782122888e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The GPIO invert registers are already defined in the PCH code, so
just use the 8-bit versions of the registers instead of creating
a new GPIO field for the single bits.
This allows us to get rid of the Field(GPIO...) code that's causing
problems with IASL version 20190509.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iac5dfb71b3a2b5a25c05a403cf5f403c7acecaaf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
At least one channel must be present, so print an error if there is
not. However, we cannot always assume it will be the first channel,
so make the appropriate selection when printing the timings.
Found-by: Coverity Scan #1370{584,585,588,589,590-596,600}
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I6b59989242e498474782876302e0850e3e4cf2d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The gpio table is only used by depthcharge, and depthcharge rarely
has a need for the "recovery" gpio. On a few boards it does use the
gpio as a signal for confirming physical presence, so on that boards
we'll advertise the board as "presence".
All these strings probably should have been #defines to help avoid
typos (e.g., the "ec_in_rw" in stout seems questionable since everybody
else uses "EC in RW").
Cq-Depend: chromium:1580454
BUG=b:129471321
BRANCH=None
TEST=Local compile and flash (with corresponding changes to depthcharge)
to 2 systems, one with a "presence" gpio and another without. Confirmed
that both systems could enter dev mode.
Change-Id: Id6d62d9e48d3e6646cbc1277ea53f0ca95dd849e
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Depthcharge uses the keyboard type to help determine whether
it can trust the keyboard for security-sensitive confirmations.
Currently it trusts anything except usb, but now there's a need
to distrust ec-based ps/2 keyboards that are associated with untrusted
ECs. To help facilitate this, coreboot needs to report more
details about non-usb keyboards, so this change replaces the current
instances of unknown with enum values that distinguish uart and gpio
from ec-based keyboards.
BUG=b:129471321
BRANCH=None
TEST=Local compile and flash to systems with trusted and non-trusted
ECs. Confirmed that security confirmation can't be performed via
keyboard on a system with an untrusted EC but can still be performed
on a system with a trusted EC.
Change-Id: Iee6295dafadf7cb3da98b62f43b0e184b2b69b1e
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
A12 is not current set for ISH_GP6 so the ISH_LID_CL#_TAB
signal is not making it to the ISH properly. Enable the second native
function instead of the first.
BRANCH=none
BUG=b:131785573
TEST=gpioget on ISH now shows the correct gpio level
Change-Id: Ib3a654ae659037263aa9aa29d45b42ca67b7955b
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32738
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Systems with C_EVIRONMENT_BOOTBLOCK and VBOOT enabled requires functions
tsc_freq_mhz(), vbnv_cmos_failed() and vboot_platform_is_resuming()
in verstage.
Add tsc_freq.c and pmutil.c to verstage.
BUG=NA
TEST=Booting Embedded Linux on Facebook FBG-1701 + Building Google Banon
Change-Id: Ia509eda6bf415aaa63be71013249493aa472289d
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
It is possible that 'malloc_fo_sub' and 'remalloc_fo' can
fail, so add appropriate error checks for those cases.
This incidentally fixes a possible memory leak when
'malloc_fo_sub' succeeds but 'remalloc_fo' does not.
Found-by: Coverity Scan #1396050
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I944b67f5cdcfd7a687e81d8bb01a209c9dc9b0b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
As the previous comment indicated, this null check is
currently superfluous, but adding it in makes Coverity
happy, and future-proofs the code in case someone changes
the internals of 'find_fcba' later and forgets/doesn't know
to update this error check.
Found-by: Coverity Scan #1395066
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I594cd0098f5b36cef5b3efc4c904710d3ba9b815
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32691
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This patch ensures start_cpu() function to store default_apic_id using
common cpu_add_map_entry() function to make cpu_index() implementation
generic.
BRANCH=none
BUG=b:79562868
Change-Id: Iac4d6e9e6e6f9ba644335b4b70da8689c405f638
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This cpu_index() implementation assumes that cpu_index() function
might always getting called from coreboot context (ESP stack
pointer will always refer to coreboot).
This might not be true in case of proposed PI spec MP_SERVICES_PPI
implementation, where FSP context (stack pointer refers to fsp)
will request to get cpu_index(), natural alignment logic will
use ESP and retrieve struct cpu_info *ci from (stack_top - 8 byte).
This is not the place where cpu_index is actually stored by
ramstage c_start.S
Hence this patch tries to remove those dependencies while retrieving
cpu_index(), rather it uses cpuid to fetch lapic id and matches with
cpus_default_apic_id[] variable to return correct cpu_index().
BRANCH=none
BUG=b:79562868
TEST=Ensures functions can be run on APs without any failure and
cpu_index() also provides correct index number.
Change-Id: I55023a3e0cf42f0496d45bc6af8ead447f402350
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26346
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We keep the support, though. Just now that `libgfxinit` is fixed, we
don't need the distinction anymore. Causally, we also don't need
CPU_INTEL_MODEL_306AX any more.
TEST=Played tint on kontron/ktqm77. Score 606
Change-Id: Id1e33c77f44a66baacba375cbb2aeb71effb7b76
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Beside one tiny fix for framebuffer scaling, this contains a major
refactoring of libgfxinit's configuration infrastructure. With this,
we are finally able to detect CPUs at runtime and only have to confi-
gure a CPU/GPU generation.
Change-Id: Iccf4557453878536f527e4a1902439a1961ab701
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32736
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch renames mp_get_apic_id() to cpu_get_apic_id() and
add_cpu_map_entry() to cpu_add_map_entry() in order access it
outside CONFIG_PARALLEL_MP kconfig scope.
Also make below changes
- Make cpu_add_map_entry() function available externally to call
it from mp_init.c and lapic_cpu_init.c.
BRANCH=none
BUG=b:79562868
Change-Id: I6a6c85df055bc0b5fc8c850cfa04d50859067088
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Enable VT-d through fsp upd VtdDisable. Update remapping structure
types in numerical order as all remapping structures of type 0 (DRHD)
enumerated before remapping structures of type 1 (RMRR), and so forth.
BUG=b:130351429
TEST=Booted to kernel and verified the DMAR table contents.
Change-Id: I1d20932e417b9d324edd98c8f2195dc228d2e092
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
We've been assuming that ENV_RAMSTAGE is always the payload loader.
In order to test out different models, we need a way to mark the
"stage we are in" as the payload loader.
Define a new rule, ENV_PAYLOAD_LOADER. For now, it is set
to ENV_RAMSTAGE. It is not used yet pending approval of this
approach.
Change-Id: I7d4aa71bad92987374d57ff350b9b0178ee7c12b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch moves vboot_logic_executed() (and its dependencies) into a
header and turns it into a static inline function. The function is used
to guard larger amounts of code in several places, so this should allow
us to save some more space through compile-time elimination (and also
makes it easier to avoid undefined reference issues in some cases).
Change-Id: I193f608882cbfe07dc91ee90d02fafbd67a3c324
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Some edk2 vendorcode headers define an ASSERT macro. They're guarded
with an #ifndef ASSERT, but if coreboot's assert.h gets included after
that header, we still have a problem. Add code to assert.h to undefine
any rogue definitions that may have already been set by vendorcode
headers.
This is ugly and should only be a stopgap... it would be nice if someone
maintaining those vendorcode parts could eventually replace it with a
better solution. One option would be to use a "guard header" for every
vendorcode header we want to pull into normal coreboot code which would
chain-include the vendorcode header and then undefine anything that
clashes with coreboot again.
Change-Id: Ibf8dc8b2365821e401ce69705df20aa7540aefb2
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds another check to vboot_logic_executed() to make sure we
only do a runtime check for verstage_should_load() if
CONFIG_VBOOT_RETURN_FROM_VERSTAGE is enabled. That's the only case where
the stage that's loading the verstage can execute after verification has
run (because the verstage will return to it when it's done). In the
other case, the stage that loads verstage really just loads it and will
never do anything again after hand-off, so it's guaranteed to always
execute before verification.
This change may allow extra dead-code elimination in some cases.
Change-Id: I7019b6f7b0acfbf0a8173914b53364751b08f2cf
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Leakage power is observed from TOUCH_SCREEN_PD# (GPP_E7 which is connected
to RESET pin of Wacom controller) during S5.
To avoid leakage power, GPP_E7 needs to be turned off before S5 entry.
BUG=b:129899315
TEST=Measure leakage power in S5 from both Arcada and Sarien
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie4229477b7149c0a75f4a8c6c7c453a37cc1c78c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
PCI_MIN_GNT is defined at offset 0x3e in <pci_def.h> which does not
apply to this PCI bridge because it is only defined for
"Header type 0 (normal devices)" (line 82).
Some lines obove that code line, the "write" on BCTRL is already done.
Change-Id: I8f1b98ba627947ab6652a4ba31d2acb159dd3e32
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32700
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PCI_MIN_GNT is defined at offset 0x3e in <pci_def.h> which does not
apply to this PCI bridge because it is only defined for
"Header type 0 (normal devices)" (line 82).
BCTRL registry for D30:F0 is defined at offset 0x3e for i82801gx
(see ICH7 Family Datasheet page 355).
The write on that register is already done some lines above.
So remove wrong register name and the wrong code line.
Change-Id: Ib8a0514200f424049503bb8e4bc076ee6ae86ce3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add vbt files for nami variants and select Kconfig option
to utilize them. The default vbt is automatically added
by the Kconfig selection and so does not need to be
specified in the makefile with the others.
Test: boot vayne and akali nami variants, verify
display functional and correct vbt loaded.
Change-Id: Iaf49bdee7ae82a0a61192327351267f098eb5ab1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Correct Micron MT40A512M16TB-062E:J SPD CRC to 0x5330 to fix post hang
in AGESA TestPoint:05 TpProcMemSPDChecking.
BUG=b:127394249
BRANCH=master
TEST=emerge-grunt coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Change-Id: I8fa49e6e938b3195945b3199438cc53f3e9c92e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The ASL 2.0 syntax for "!X" resolves to "LNot(X)" which will evaluate
the object as an integer and turn into a boolean. This may not do the
right thing if the object is actually a string and it can lead to
unexpected behavior.
Instead be specific about the object type and check for zero or an
empty string depending on what is being returned.
This fixes an issue where some VPD keys were causing the search to
stop and miss subsequent entries.
Change-Id: I1688842964f9c2f81ca31073da9c2d71a8c81767
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Should include vb2_sha.h header when SHA library functions or
constants are required. This replaces NEED_VB2_SHA_LIBRARY.
BUG=b:124141368, chromium:956474
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I9f32174dbf3de05fbe5279cb8017888757abf368
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:1583820
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Input: tell vb2api_fw_phase1 if display unconditionally available
Output: vb2api_fw_phase1 may request coreboot to initialize
display, if needed based on some internal request
Move setting the VBOOT_FLAG_DISPLAY_REQUESTED flag into
verstage_main.
BUG=b:124141368, b:124192753, chromium:948529
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I81c82c46303564b63b8a32e7f80beb9d891a4628
Cq-Depend: chromium:1564232
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The VbInitParams struct will be deprecated. Remove its
use in preparation.
Additionally, remove use of the flag
VB_INIT_OUT_ENABLE_USB_STORAGE, which is no longer used
downstream since vboot_reference CL:347257.
BUG=b:124141368, chromium:960226
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ibe02cb6ba639de0d7cbdf79fc4dbf49044c92278
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:1583943
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32664
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use CondRefOf to replace config optios for PTS/WAK acpi method dynamic
loading. Then we can move EC PTS and WAK method to be under mainboard.
BUG=N/A
TEST=Build sarien source code, check build/dsdt.dsl have EC.PTS method
included, build whlrvp soure, check build/dsdt.dsl don't have EC.PTS
method. Both able to build pass.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I9f4bd7240832caf070e65039e4ba2d8656371da8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32371
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable VBOOT support on all devices that have a 8 MiB flash, using a
single RW_MAIN_A partition, allowing the use of tianocore payload in
both RW_MAIN_A and WP_RO.
* Add VBNV section to cmos.layout
* Add FMAP for VBOOT and regular boot
* Select Kconfigs for VBOOT
* Enable VBOOT_SLOTS_RW_A by default
Also build test VBOOT on Lenovo T420.
Tested on Lenovo T520 using Icb7b263ed86551cc53e1db7babccaca6b3ae2fe6.
Change-Id: Icb7b263ed86551cc53e1db7babccaca6b3ae2fe6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
* Add function to wait for sense registers to become valid.
* Add function to retrieve Fn-Key state.
Tested on Lenovo T500:
* It takes about 700msec for the registers to become valid.
Tested on Lenovo T520:
* It takes less than 150msec for the registers to become valid.
Change-Id: Ie27e2881a256c4efb3def11f05070c446db6e5fc
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add the new field 'smbios_slot_desc', which takes 2 to 4 arguments.
The field is valid for PCI devices and only compiled if SMBIOS table
generation is enabled.
smbios_slot_desc arguments:
1. slot type
2. slot lenth
3. slot designation (optional)
4. slot data width (optional)
Example:
device pci 1c.1 on
smbios_slot_desc "21" "3" "MINI-PCI-FULL" "8"
end # PCIe Port #2 Integrated Wireless LAN
Tested on Lenovo T520.
Change-Id: If95aae3c322d3da47637613b9a872ba1f7af9080
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Checking the PrimaryDisplay parameter (added by patch with Change
Id Ie3f9362676105e41c69139a094dbb9e8b865689f) isn`t required. The
display connected to PEG works even if IGD is primary for output
image and at the same time this device is disabled
Tested on Asrock H110M-DVS with NVIDIA GTX 1060 GPU
Payload: tianocore edk2-stable201811-216-g51be9d0
Change-Id: I5615597881a151bb004676d914fbf40874ac1f68
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32615
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
`pei_data` was a struct with blob parameters from pre-FSP times.
Somehow, it sneaked into upstream FSP1.1 support (probably because
early board ports were written for a different blob). When added
upstream, its usage was already perverted. It was declared at SoC
level but mostly used to pass mainboard data from mainboard code
to itself and FSP data from FSP code to itself. Now that no board/
SoC code uses it anymore, we can finally drop it.
Change-Id: Ib0bc402703188539cf2254bdc395cca9dd32d863
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The SoC specific `struct pei_data` was filled with values that were
never consumed anywhere again. So just merge the used code into
`romstage.c` where it's effectively used.
Change-Id: I499b3cfcdd5400ea132749555d433a2d8a9471a3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The SoC specific `struct pei_data` was filled with values that were
later only consumed by the mainboard code again. Avoid jumping through
this hoop and fill FSP UPDs directly.
Change-Id: I040f4a55b4f4bad3f6072920e5e2eceded4cb9bb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The SoC specific `struct pei_data` was filled with values that were
later only consumed by the mainboard code again. Avoid jumping through
this hoop and fill FSP UPDs directly.
The provided solution locates the SPD data in CBFS again to fill SMBIOS
tables. This is not perfect. OTOH, this code isn't mainboard specific
and doesn't belong here anyway.
Change-Id: Ib6103d5b9550846fe17c926631a013ff80b9598f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32593
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The SoC specific `struct pei_data` was filled with values that were
later only consumed by the mainboard code again. Avoid jumping through
this hoop and fill FSP UPDs directly.
Change-Id: I399dd89f85ccea43fdf90bd895e71324f4b409cc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The SoC specific `struct pei_data` was filled with values that were
later only consumed by the mainboard code again. Avoid jumping through
this hoop and fill FSP UPDs directly.
Change-Id: Ibc013ccea9f83ef29f22fe2da4c0d12096308636
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This reverts commit c4ab50cdde.
Reason for revert:
vboot recently was changed so that -Wtype-limits fails, and that
was just brought upstream. Since vboot internals are more likely
to be used elsewhere while -Wtype-limits is less critical, revert
this until vboot is resolved, then bring -Wtype-limits back again.
Change-Id: I9cce10462b9e57189513fa49e11fd27ebe35ba51
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32670
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id 304aa429:
2019-03-12 10:38:56 -0700 - (futility: updater: Unit test for preserving sections using FMAP flags)
to commit id e7edff66:
2019-05-03 07:02:32 -0700 - (vboot: implement DISPLAY_INIT context and SD flag)
This brings in 45 new commits.
Change-Id: I7493e43bddc553f9724de46130ccb4cb44e18573
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Remove use of deprecated GoogleBinaryBlockHeader struct, and
replace with vb2_gbb_header.
BUG=b:124141368, chromium:954774
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Iee3bd877cb1791a689efdeabda324f43f7d0c6f2
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32455
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Sunrise Point-LP is used on Skylake and KabyLake platforms,
but the PCH IDs differ.
This commit adds the PCH IDs for Skylake mobile platforms
and renames the Kabylake macros to distinguish them.
Used Intel documents:
- 332995-001EN (I/O datasheet vol. 1)
- 332996-002EN (I/O datasheet vol. 2)
Change-Id: Id46224fcc44b06c91cbcd6c74a55c95e1de65ec6
Signed-off-by: Felix Singer <migy@darmstadt.ccc.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Part of this checks whether tolum_base and cbmem_top are the same - however,
cbmem_top hasn't been initialised at the point where this call occurs.
Change the ordering to fix that.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Change-Id: Ib89e0513bdc35c3751a9d4c2a2789a2836046789
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32530
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reset GPI Interrupt status and enable registers from ramstage instead of
bootblock so that it applies to devices in field.
BUG=b:130593883
BRANCH=octopus
TEST=Ensure that the Interrupt status & enable registers are reset
during the boot up when the system is brought out of G3, S5 & S3. Ensure
that the system boots fine to ChromeOS.
Change-Id: Ib11b580ceb23bd1fe789f549b667a8ced2d859a1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32534
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A hook for romstage is already existing but not for ramstage.
It's very useful for debugging as it allows to run code
for testing purposes by the mainboard. Also, it allows to
run configuration code or configure FSP options, which
don't have a devicetree option.
Change-Id: I9edc543943c5cbc696fc6c615cb77ef68294c980
Signed-off-by: Felix Singer <felix.singer@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Remove the bridge enable step of accessing D14F0x64. This method for
enabling the bridge appears to be last present in the SB700 device.
Beginning in the SB800 (and all FCH, SoC devices), the enable is in
PMxEC[0]. Since the bridge is enabled in bootblock to allow port 80h,
there is no need to maintain it in ramstage.
Correct the device used for misc. configuration of the LPC bridge.
The #defined value removed is 14.0 but the settings are in 14.3.
TEST=Boot Grunt, check console and dmesg for errors and warnings
BUG=b:131862871
Change-Id: I078be974dc3c78c94cb7c0832518f21bac029ff2
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
This patch enables -Wtype-limits for the whole repository, which
disallows checking for a condition that must be always true or always
false based on type width (e.g. checking whether an unsigned variable is
negative or whether a 32-bit integer is larger than 4G). This helps
avoid easy to make and hard to find (because they often only affect
error paths) mistakes like
size_t size = fmap_read_area(...);
if (size < 0)
die("If only the compiler could've told me to use ssize_t instead");
Change-Id: I19edabfd092d09dad720e3fc47b44838163bfe25
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32536
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch fixes up all code that would throw a -Wtype-limits warning.
This sometimes involves eliminating unnecessary checks, adding a few odd
but harmless casts or just pragma'ing out the warning for a whole file
-- I tried to find the path of least resistance. I think the overall
benefit of the warning outweighs the occasional weirdness.
Change-Id: Iacd37eb1fad388d9db7267ceccb03e6dcf1ad0d2
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32537
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I can't claim that I really understand what this code does, but it looks
like there are platforms that use code from lib/spd_bin.c without
enabling CONFIG_GENERIC_SPD_BIN. Some functions in that file contain
references to CONFIG_DIMM_MAX, so that option probably shouldn't depend
on CONFIG_GENERIC_SPD_BIN.
Change-Id: I041c52b6bd255e9a9920e5a101165ba5fc5fa6f3
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32548
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the Librem 13v3 as a separate board; instead build a
single firmware image for the 13 v2/v3 boards.
Clean up Kconfig options:
- remove entries for 13v3 board
- fold entries into a single line where possible
- remove redundant MAINBOARD_VERSION option (will default to 1.0)
- remove unused microcode length/location (only needed for FSP CAR)
Test: build/boot Librem 13 v2/v3 boards with same image
Change-Id: Ic09b8ec5c576f4c4c48ef30ee3f60a4c2c286cd3
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Make use of:
* southbridge/intel/common/rcba.h
* southbridge/intel/common/pmbase.c
* defines in pch.h
Get rid of dependency to DEFAULT_RCBA.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I879fce6a5bb80499e1986e618a1422a7aaa3a0c0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32066
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updated GPP_A8 to be a GPI and SCI source, to support both wake and
notifications.
BUG=b:128941098
BRANCH=none
TEST=Compiles, simulated pen eject with PCH_INT_L signal. Both evtest
and waking from s0ix confirm this works. The output of /proc/interrupts
confirms the correct interrupt is triggered.
Change-Id: I080fb3cbfb3e2f55209ca31824b00ca820d70f78
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Added macro named PAD_CFG_GPI_GPIO_DRIVER_SCI, for pads that need to be
configured as GPI, GPIO Driver mode, and SCI interrupt.
Also remove PAD_IRQ_CFG_DUAL_ROUTE macro (subsumed by
PAD_CFG_GPI_IRQ_WAKE).
BUG=none
BRANCH=none
TEST=Compiles
Change-Id: I0332c64e2fa62ce29c772444606adbfdf9c9afc4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32485
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change removes all the separate entrypoint dispatch
functions as they all share the same pattern.
Furthermore, none of the function definitions under vendorcode
binaryPI/AGESA.c file have proper declarations, the ones compiler
picks up from AGESA.h are for the internal implementations and
with sanely organized headerfiles would not be exposed outside
the build of AGESA at all.
Change-Id: I0b72badc007565740c93b58743cfd048e8b42775
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31485
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Due to PCB limitations the SD-Card interface is not able to operate
with the highest frequency reliably. The OS driver will switch to
the highest mode if a SD-Card is attached which supports this high
frequency mode. In order to work around this PCB limitation disable the
high frequency modes in the controller capabilities (SDR104 and HS400
mode) and leave SDR50 and DDR50 enabled.
Change-Id: Ia5fed5fb70b027de34170b49620927614a00fb7a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The entry for drivers/intel/fsp1_0/Kconfig was added under the
chipset menu before addtional FSP versions were added, and the
drivers/*/*/Kconfig entry added to support them. This results
in the fsp1_0 Kconfig items being duplicated in the Chipset and
Generic Drivers menus.
Remove the chipset entry since it's no longer needed.
Test: select FSP 1.0 mainboard (e.g. intel/minnowmax) in menuconfig,
observe FSP 1.0 Kconfig entries listed only under Generic Drivers menu.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: If1e78fb9259b1a46d308db829881eb3b3d17cf40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32565
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB acts as I/O handler for QCLib (e.g. DDR training data)
This interface allows bi-directional data flow between
CB and QCLib
Tested and working interfaces:
DDR Training data
QCLib serial console output
DDR Information (base & size)
limits cfg data
TEST=build & run
Change-Id: I073186674a1a593547d1ee1d15c7cd4fd8ad5bc1
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Now that support has been added for using the public FSP
repo for Braswell platform, clean up Kconfig options and
set sane defaults when using it.
The following changes have been made:
- add option to use the 3rdparty/fsp repo for Braswell platform
- reorder FSP 1.1 Kconfig entries for improved flow/readability
- set the default path for the FSP binary based on use of FSP
repo and platform
- set the CBFS location for the FSP binary based on platform
Change-Id: Ie2f732bf0ac4d4551908caa56360b8bb2869b4c7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The current Braswell FSP 1.1 header in vendorcode/intel, for
which there is no publicly available FSP binary, contains silicon
init UPDs which are not found in the publicly available header/binary
in the FSP Github repo. This prevents new boards from being added
which use the public Braswell FSP header/binary.
To resolve this, move the UPDs not found in the public header from
the soc's chip.c to ramstage.c for the boards which use them. Add
a Kconfig option to use the current non-public FSP header and
select it for boards which need it (google/cyan variants); set the
public FSP option as the default. Use the Kconfig option to set
FSP_HEADER_PATH to ensure the correct header is used.
Test: build google/cyan and intel/strago using non-public and
public FSP header/binaries respectively.
Change-Id: I43cf18b98c844175a87b61fdbe4b0b24484e5702
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Rather than selectively update the fsp submodule based on
FSP version or platform selection, update it when building
for any FSP-enabled platform, so all have latest version available.
Change-Id: If07d55828a1863623e04a4ecdd1514c3cb6d9c11
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Main objective for this change is to export the bluetooth reset
gpio to the kernel for use in an rf-kill operation.
To do so, we enable USB acpi and define all of the USB2 devices,
which includes bluetooth's reset gpio information.
BUG=b:122540489
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage
$cat sys/firmware/acpi/tables/SSDT > /tmp/ssdt.dat &
retrieve ssdt.dat from DUT &
$iasl -d ./ssdt.dat & check the HS03 node is with "reset-gpio"
under _DSD object
Change-Id: I411ef707782655361bd1b8ac2b914b8ae64defeb
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Caveh Jalali <caveh@google.com>
This patch adds code to initialize two USB DWC3.0 controllers
and its associated QUSB V2 10nm PHYs to the SDM845 SOC, and uses them to
initialize USB3.0 on the cheza mainboard.
Synopsis controller initialization and configuration sequences taken from
USB 3.0 HPG chapter 2.2 and refer PHY HPG chapter 10.2 for QUSB phy
programming.
Includes Super speed mode support.
TEST=USB keypad and mass-storage device enumeration tested with this patch
Change-Id: I475a7757239acb8ef22a4d61afd59b304a7f0acc
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This implementation corrects the GPE DWx mapping for GPIO groups.
The assignments is done in GPIO MISCFG register for all GPIO communities.
And configures the which GPIO communities get register as Tier1.
Change-Id: I9c306d46e5194944def26c24cdb95f5ebada42b8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This patch ports CB:31787 and CB:31908 changes from CNL to ICL.
This change moves soc_fill_power_state and soc_prev_sleep_state to
pmutil.c. It allows the functions to be used across romstage and smm.
Also fix GEN_PMCON bit checks as below:
ICL PCH has PWR_FLR, SUS_PWR_FLR and HOST_RST_STS bits in GEN_PMCON_A
and so this change updates the check for these bits to use GEN_PMCON_A
instead of GEN_PMCON_B.
Change-Id: Ib7ab95b7bbcc97a076d27a11db2105f7b976b521
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32506
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ports CB:30718 and CB:31908 changes from CNL to ICL.
Add logging of chipset events on boot into the flash event log.
This was tested on a google/dragonegg board to ensure that events
like "System Reset" are added to the log as expected.
Also fix GEN_PMCON bit checks as below:
ICL PCH has PWR_FLR, SUS_PWR_FLR and HOST_RST_STS bits in GEN_PMCON_A
and so this change updates the check for these bits to use GEN_PMCON_A
instead of GEN_PMCON_B.
Change-Id: I25ec32e81f8801f8d5e69c6095ffed73d75dded6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This patch ports CB:31902 changes from CNL to ICL.
The prev_sleep_state value was showing 5 even after warm reboot, once the
SUS_PWR_FLR bit is being set. This bit was not being cleared.
Hence clearing the PMCON status bits.
Change-Id: Ia07aa17b4491216a277c36edfe6ed2aa489287c6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32503
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 351e3e5 ("src: Use include <console/console.h> when appropriate")
has broken the build here, see below, so we include console.h here again.
In file included from src/device/oprom/x86emu/x86emui.h:65,
from src/device/oprom/x86emu/debug.c:40:
src/device/oprom/x86emu/debug.c: In function 'x86emu_dump_regs':
src/device/oprom/x86emu/debug.h:46:22: error: implicit declaration of function 'printk'; did you mean 'printf'?
[-Werror=implicit-function-declaration]
#define printf(x...) printk(BIOS_DEBUG, x)
^~~~~~
src/device/oprom/x86emu/debug.c:366:5: note: in expansion of macro 'printf'
printf("\tAX=%04x ", M.x86.R_AX );
^~~~~~
Fixes: 351e3e5 ("src: Use include <console/console.h> when appropriate")
Change-Id: I75d0b7c08bfa6dcb07778bbb762223b62cfc3da7
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
For GPIO pads that are configured as no-connect (PAD_NC), setting it
as GPI (with Rx enabled) leads to GPE0_STS being set
incorrectly. Though this is not an issue in practice (GPE0_EN is not
set, so no events triggered), it can confuse users when debugging GPE
related issues.
This change configures PAD_NC to have Rx disabled along with Tx to
ensure that it does not end up setting GPE0_STS bits for unwanted
GPIO pads.
P.S.: IOSSTATE config does not have a TxDRxD setting, so leaving that
configuration as is.
BUG=b:129235068
TEST=Verified that GPE0_STS bits are not set for pads that are marked
as PAD_NC.
Change-Id: I726cc7b86a94e7449352cd8a8806d4d775c593dc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Increase ramstage to 2M, required to actually embed the 7.2mb uImage
into the coreboot.rom, increase the postram cbfs cache in order for the
fit image to be loadable (without this increase the fit payload is found
but not loaded)
Change-Id: Iee0ed9f7958588ceda54bb32253c84cac68abea2
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The name OPROM is somewhat inaccurate, since other steps to bring
up display and graphics are needed depending on mainboard/SoC.
This patch cleans up OPROM code nomenclature, and works towards
the goal of deprecating vboot1:
* Rename CONFIG_VBOOT_OPROM_MATTERS to
CONFIG_VBOOT_MUST_REQUEST_DISPLAY and clarify Kconfig
description
* Remove function vboot_handoff_skip_display_init
* Remove use of the VbInit oflag VB_INIT_OUT_ENABLE_DISPLAY
* Add |flags| field to vboot_working_data struct
* Create VBOOT_FLAG_DISPLAY_REQUESTED and set in vboot_handoff
BUG=b:124141368, b:124192753, chromium:948529
TEST=make clean && make test-abuild
TEST=build and flash eve device; attempt loading dev/rec modes
BRANCH=none
Change-Id: Idf111a533c3953448b4b9084885a9a65a2432a8b
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Patch corrects IRQ and GPIO configuration for RT5682 codec's Jack INT.
Switching IOAPIC to GpioInt because ACPI Interrupt() doesn't support
jack triggering on both edges.
BUG=b:130180492
TEST=build and boot on a CML EVT board.
Use evtest & verify headset jack detection functions as expected.
Change-Id: Ia9bf8d554b54554f9ac1e78fd44a508964c8a14d
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Suggested-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32474
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Trusted Firmware places some components in SRAM on RK3399 and therefore
restricts accesses to SRAM to the secure world. This makes the vboot
working data inaccessible to normal world payloads, so we need to
migrate it into CBMEM.
Change-Id: Ic7c95790f2f118ccbdd897550f13b5f987bdd831
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
With the default CPU voltage (0.8v), CPU frequency should be 1417Mhz at
most. We have to raise CPU frequency to 1989MHz after increasing CPU
voltage to 1.05v in romstage.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: I4c3e0fa27ccda8e0efe422b6ab503a1efb1697e9
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
NEED_VB20_INTERNALS should always be specified when peeking
into vboot internal data structures.
BUG=b:124141368, chromium:956474
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I5a47a28350fd5a68efeff0d06ca150c1ae145412
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Disable the GBB flag forcing manual recovery now that we can read
the manual recovery from H1.
Enable the GBB flag to skip EC software sync, since images built
from coreboot.org do not include the EC binaries by default.
Change-Id: I0e1d6304e3e29eda68c7b807cf0774275c37d710
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We do not want the RX signal to be floating on the board as that could
cause the ISH to remain in a higher power state (because there is logic
to keep the ISH in an higher power state when there is an active UART).
Add an internal 20K pull up on the RX line. In normal configuration this
will burn an additional 544uW.
BRANCH=R75
BUG=b:131241969
TEST=verify that ISH console still works with rework
Change-Id: Ifc9621bcafe4c86edfa9cd6d58b307254d3a81ca
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
If the Intel IGD device pci 02.0 is disabled or undefined in
the device tree, then internal graphics pre-allocated memory
and GFX-VT MMIO memory for virtualization won`t be allocated
in the SoC address space.
Thus, patch resolves the FSP-S hang problem on Skylake/ Kaby
Lake processors when the IGD device is disabled. This should
provide to run FSP 2.0-based coreboot on these CPUs families
without integrated graphics card.
The following boards were used for testing:
- Asrock H110M-DVS board (desktop i5-6600) & NVIDIA GTX 1060
as external GPU.
Virtualization and GFX 3D acceleration with nouveau driver
still works well (tested on VirtualBox 5.1.38 with Ubuntu
18.04.1 as guest and host OS)
- Intel KBL-R U RVP board (mobile i5-8350u) without GFX.
Payload: tianocore edk2-stable201811-216-g51be9d0.
Change-Id: Id7a0cba582d83e3fe7e8d20342ee219cdd369a53
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32467
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds the setting of psys_pmax to 136W. According to the
design, Rpsys is 11.8Kohm. Here is the equation to come out the
Psys_pmax value: Psys_pmax * 1.493uA/W * 11.8Kohm / 2 = 1.2V
Hence, Psys_pmax is 136W.
BUG=b:124792558
BRANCH=None
TEST=emerge-sarien coreboot chromeos-bootimage & Ensure the value is
passed to FSP by enabling FSP log & Boot into the OS
Change-Id: Id3f6be5f0c2346a7763195a992c0ae45faede056
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Clear the GPI Interrupt Status & Enable registers to prevent any
interrupt storms due to GPI.
BUG=b:130593883
BRANCH=octopus
TEST=Ensure that the Interrupt status & enable registers are reset
during the boot up when the system is brought out of G3, S5 & S3. Ensure
that the system boots fine to ChromeOS.
Change-Id: Ia3b9d3bf08472219348e20b53bae470c589039fb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support to reset the GPI Interrupt Status & Enable registers so that
the system does not experience any interrupt storm from a GPI when it
comes out of one of the sleep states.
BUG=b:130593883
BRANCH=None
TEST=Ensure that the Interrupt status & enable registers are reset
during the boot up. Ensure that the system boots fine to ChromeOS.
Change-Id: I99f36d88cbab8bb75f12ab1a4d06437f837841cb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the offset information for GPI interrupt status and enable register
in the pad_community structure. Populate the concerned information for
individual SoCs. This offset information is required to clear the
interrupt configuration during the bootup.
BUG=b:130593883
BRANCH=None
TEST=Ensure that the interrupt configuration are cleared during bootup.
Ensured that the system boots to ChromeOS.
Change-Id: I8af877a734e8d49b700d720b736da8764985a8f8
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The ACPI code of LPE device is included regardless of the
availability of the LPE controller.
Linux remains requesting the status of device LPEA even if
this device is disabled.
Include ACPI LPE controller code at Braswell mainboards with
LPE enabled.
BUG=N/A
TEST=Linux 4.17+ on Portwell PQ7-M107
Change-Id: Ic8acf9ea9e9b0ba9b272e20beb2023b7a4716a73
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
The dqs_map array is used only for LPDDR3 and LPDDR4. It is not used for
DDR4, and so it can be removed from the baseboard memory initialization
code.
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Change-Id: I07fac3097d68f37b4630d3f0010f987da2f03bd7
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32484
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
First configuration supported is 8 GB system memory:
4 x 2 GB (K4E6E304ED-EGCG).
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: Ibd92d585118ff75492e8a7188dcdb2a286836d56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Intel's DQ_DQS_RComp_Info_Utility generates data for 6 entries. MRC will
return errors if we don't have all 6 entries in the map.
BRANCH=none
BUG=b:131103736
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Change-Id: I20a768de0e4440d7dde7b717794c4e2d0c62819c
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Changes includes:
- enable TPM1 + add entry in devicetree
- configure LPC IO to make IPMI work + add entry in devicetree
- introduce DSDT and SMBIOS entries for IPMI to make it detectable
by ipmi_si driver
Signed-off-by: Lukasz Siudut <lsiudut@fb.com>
Change-Id: Ia975643064075f1f861f4ead6f24ed71f345ea04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Enable LTR for NVMe so it can use ASPM L1.2.
BUG=b:127593309
TEST=build and boot on sarien and check L1 substate with lspci
before: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+
after: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
Change-Id: I9842beda6767f758556747f83cfcedbd00612698
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Remapping Hardware Status Affinity (RHSA) structure is applicable for
platforms supporting non-uniform memory. An ACPI Name-space Device
Declaration (ANDD) structure uniquely represents an ACPI name-space
enumerated device capable of issuing DMA requests in the platform.
Add RHSA and ANDD structures support for DMAR table generation.
BUG=b:130351429
TEST=Image built and booted to kernel
Change-Id: I042925a7c03831061870d9bca03f11bf25aeb3e7
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch revises the AC/DC loadline settings because some major
layout changes between proto and evt boards.
BUG=b:130740639
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage and boot to the OS.
Change-Id: Iea12c621e7fab427a0de8f43f0290bf01d0c5a09
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
Lynx Point switched to doing mainboard-specific super I/O setup in the
bootblock with commit d893a2635f ("sb/intel/lynxpoint: Enable LPC/SIO
setup in bootblock"). The X10SLM+-F was added while that commit was in
review, and hence did not receive the necessary changes to SIO setup.
This patch has not been tested on hardware.
Change-Id: I7a648ec967dea2113cbbde1a93c1963ca6dd3c88
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
On EC end, we want to change this pin from push-pull to open-drain.
And since there is no external pull-up resistor on the board, we'll
have to configure this pin as internal-pull-up on AP end.
BUG=b:129306003
TEST=None
Change-Id: Ibc1f89fc25773220db009c6571400b01390dd756
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
If override tree does not have any device, then the chip info
structure in it cannot be associated with the correct device and ends
up being added as a standalone chip info structure without any device
actually using it. This change prevents this condition by throwing an
error during compilation.
BUG=b:130342895
Change-Id: I7b8bb6b3228030a465976ca32ce8ef63f41365dd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Similar to hatch(CB:32278), this change sets SerialIo
config for UART0 to PchSerialIoSkipInit to skip initialization in
FSP.
This change also adds a device to kohaku override tree to ensure that
the settings in it take effect.
BUG=b:130310626
Change-Id: Ia25b45811be26d55fc0019e4cd22eb7310b5a4c4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Disable the POWER_OFF_ON_CR50_UPDATE option on sarien/arcada. This is
needed so that platform properly boots after doing a Cr50 firmware
update when running on battery.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I0b687285eb95070eaffb68611a7d98eb8434ce2c
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Modify the POWER_OFF_ON_CR50_UPDATE Kconfig option so that specific
mainboard implementations can disable the option.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I3beefaae21de61e53ae232dbdc8ea9dbb2c78cd5
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
SSD reset pin had been added on DVT2, the power sequnence requires
toggle in boot stage.
BUG=b:130741066
TEST=Boot up with simulated DVT2 platform and confirm SSD can be
detected during warm reboot.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie734875a49b8b61f8b813c473d30cbcaf4dd13d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32434
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When coreboot checks the TPM and key-ladder state it issues a reboot of
the Cr50 with a delay parameter. Older Cr50 code doesn't support the
delay parameter and reboots immediately, which prevented coreboot from
running the mainboard specific code needed for the AP to come back up.
This change calls mainboard_prepare_cr50_reset() prior to sending the
VENDOR_CC_IMMEDIATE_RESET command.
This change also fixes a false error message from the coreboot log that
indicated "Unexpected Cr50 TPM mode 3" when the Cr50 key ladder is
disabled.
BUG=b:130830178
BRANCH=none
TEST=build coreboot on sarien and grunt platforms.
TEST=Load Cr50 v3.15, run 'gsctool -a -m disable; reboot'. Verify
corebot send the
VENDOR_CC_IMMEDIATE_RESET command and that the AP boots normally.
Verify event log shows "cr50 Reset Required"
TEST=Force Cr50 automatic update. Verify event log shows "cr50 Update
Reset".
Change-Id: Ib05c9cfde8e87daffd4233114263de5b30822872
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Commit 45d4b17 [nb/intel/sandybridge: Move southbridge code to bd82x6x]
moved early_pch_init() to the southbridge, but failed to include
early_pch.c for the non-native raminit case, which now fails to link.
As all boards default to native raminit, this was missed by the autobuilder.
Adjust early_pch.c to be compiled regardles of ram init type used
Test: build/boot google/stout with MRC ram init selected
Change-Id: I50db30fda9a1099fb434c04ea97bcc38f8455233
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Parameter passing is incorrect here, it should pass
complete StdHeader instead of attempting to fill
in HeapStatus that should be treated as a field private
to AGESA, based on where it is defined in the header
files.
Furthermore the while() loop did not evaluate the
return value. Feature can be brought back at a later
date after someone verifies it actually works correctly
across different stages.
Change-Id: Ib243b275f8700ecaeb330772c795d305c61899c5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31484
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Each entrypoint to AGESA goes through the same sequence
and have same the function signature.
To avoid introducing bunch of preprocessor magic, rename
all the agesawrapper_amdXXX() functions that are actual
entrypoints to AGESA API, make them static, and provide
a single exposed entry function agesa_execute_state().
Change-Id: I96ae1874132da3843aa42c2f4e8a59ec771d3893
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31483
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Arcada during S0iX
Change-Id: I4b8f3fdc0d107b080c5febe6fa5d29ea5d1ed0fc
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
This change is mainly to control PlatformDebugConsent FSP UPD.
PlatformDebugConsent is enabled if SOC_INTEL_CANNONLAKE_DEBUG_CONSENT != 0.
PlatformDebugConsent in FspmUpd.h has the details.
BUG=b:130203864
TEST=boot ok and PlatformDebugConsent can be controlled by Kconfig
Change-Id: Ib845b5e42bc78fb352a0c97c6301f2aeca522f29
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32297
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Support for ACPI specification version 6.3:
Add PCC operation region support for the AML interpreter. This adds PCC
operation region support in the AML interpreter and a default handler for
acpiexec. The change also renames the PCC region address space keyword to
PlatformCommChannel.
Support for new predefined methods _NBS, _NCH, _NIC, _NIH, and _NIG.
These methods provide OSPM with health information and device boot
status.
PDTT: Add TriggerOrder to the PCC Identifier structure. The field value
defines if the trigger needs to be invoked by OSPM before or at the end
of kernel crash dump processing/handling operation.
SRAT: Add Generic Affinity Structure subtable. This subtable in the SRAT
is used for describing devices such as heterogeneous processors,
accelerators, GPUs, and IO devices with integrated compute or DMA
engines.
MADT: Add support for statistical profiling in GICC. Statistical
profiling extension (SPE) is an architecture-specific feature for ARM.
MADT: Add online capable flag. If this bit is set, system hardware
supports enabling this processor during OS runtime.
New Error Disconnect Recover Notification value. There are a number of
scenarios where system Firmware in collaboration with hardware may
disconnect one or more devices from the rest of the system for purposes
of error containment. Firmware can use this new notification value to
alert OSPM of such a removal.
PPTT: New additional fields in Processor Structure Flags. These flags
provide more information about processor topology.
NFIT/Disassembler: Change a field name from "Address Range" to "Region
Type".
HMAT updates: make several existing fields to be reserved as well as
rename subtable 0 to "memory proximity domain attributes".
GTDT: Add support for new GTDT Revision 3. This revision adds information
for the EL2 timer.
iASL: Update the HMAT example template for new fields.
iASL: Add support for the new revision of the GTDT (Rev 3).
More changes in this version at https://acpica.org/node/166
Change-Id: I3a825f568423c3a703ad1c13da976af322ed9de2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Release Note :
https://cmake.org/cmake/help/v3.14/release/3.14.html
"The FindFontconfig module added by 3.14.0 accidentally used uppercase
FONTCONFIG_* variable names that do not match our conventions.
3.14.1 revises the module to use Fontconfig_* variable names.
This is incompatible with 3.14.0 but since the module is new in the 3.14
series usage should not yet be widespread"
Change-Id: Ief7f5e8309597093f061789926bd3bd2ed3aec2d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When the components like LCM ID are not installed (i.e., NC), ADC will
return some value with much larger variation from standard value (out of
the tolerance we set). To support that, we should check tolerance only
on non-NC voltages.
Also improve the error messages so we can see the ADC raw values
instead of simple assertion error (which makes debugging more difficult
since we have to build another firmware image just to print the values).
BUG=None
TEST=Booted on Kukui and got correct SKU ID for NC LCMID.
BRANCH=None
Change-Id: I8d00956e0e3b48ddbcaa505dd3ade24720c3b4ad
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32353
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, Arcada only supports D3hot during S0iX and there is leakage
power around 5~10mW depending on SSD vendors.
To support D3cold for SSD during S0iX, one MOSFET will be added on DVT2
and two GPIOs are required to be configured.
GPP_H13 is to control SSD_SCP_PWR_EN(power enable) and GPP_H12 is to
control SSD reset.
BUG=b:130741066
TEST=Measure SSD power during S0iX from Arcada(DVT2)
Change-Id: I868590e9e85d5df07930a3681884e3fc3a5c4d50
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32361
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since there is no standardized naming scheme for the
FSP binaries, the option USE_FSP_REPO can't be used
on some platforms, because some of the filenames differ
and the build process awaits "Fsp_*.fd" as filename.
As a workaround, add the option -n to SplitFspBin.py,
which defines the basename.
Change-Id: Idc684ad00033ffafd1090fc32b23549ce9603b4f
Signed-off-by: Felix Singer <migy@darmstadt.ccc.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30930
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previously Haswell used a romcc bootblock and starting verstage in
romstage was madatory but with C_ENVIRONMENT_BOOTBLOCK it is also
possible to have a separate verstage.
This selects using a separate verstage by default but still keeps the
option around to use verstage in romstage.
Also make sure mrc.bin is only added to the COREBOOT fmap region as it
requires to be run at a specific offset. This means that coreboot will
have to jump from a RW region to the RO region for that binary and
back to that RW region after that binary is done initializing the
memory.
Change-Id: I3b7b29f4a24c0fb830ff76fe31a35b6afcae4e67
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26926
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This puts the cache-as-ram init in the bootblock.
Before setting up cache as ram the microcode updates are applied.
This removes the possibility for a normal/fallback setup although
implementing this should be quite easy.
Tested on Google peppy (Acer C720).
Setting up LPC in the bootblock to output console on SuperIOs is not
done in this patch, hence BOOTBLOCK_CONSOLE is not yet enabled by
default.
Change-Id: Ia96499a9d478127f6b9d880883ac41397b58dbea
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Updating iPXE stable from commit id fd6d1f4660:
Fri Mar 31 09:08:13 2017 +0300
[thunderx] Use ThunderxConfigProtocol to obtain board configuration
to commit id ebf2eaf515:
Mar 18 10:24:08 2019 +0000
[intel] Add PCI ID for I219-V and -LM 6 to 9
This brings in 176 new commits
Change-Id: Id35fee38e0e61897a623dae35f42fc580e32d3ee
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Ensure Kohaku GPIO pins are configured correctly w/r/t Hatch. Implement the
base/override model for GPIOs (regular and early). The 'hatch' baseboard
contains the base GPIOs, and variants can override individual pads.
BUG=b:129707481
BRANCH=none
TEST=Compiles for all variants.
Change-Id: Ie5c83a0538d367ea11e9499f21cea41891d7a78e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Integrated graphics id 0x3ea1 reported as unknown in bootblock stage,
make it correct.
BUG=N/A
TEST=Boot up into sarien platform and check with serial log, it shows
IGD: device id 3ea1 (rev 02) is Whiskeylake ULT GT1.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I2c4c697b108be7fa74736514ca71469a1ca29c22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Add SMBIOS type 16 table for physical memory array, there's two item had
been left over.ECC and max capacity, as of now we set it to fixed value
as all the platform support by Intel common code don't support ECC
memory and so far the biggest capacity is 32GB.
BUG=b:129485635
TEST=Boot up with Sarien platform and check with dmidecode, the
following is the result:
Handle 0x000D, DMI type 16, 23 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 32 GB
Error Information Handle: Not Provided
Number Of Devices: 2
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: If9c5831956ef273c84d831a2b1572b3442eed961
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32286
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Match SMBIOS type 17 device locator with motherboard silk screen,using
"DIMM-A" and "DIMM-B" instead of "Channel-0-DIMM-0" and
"Chaneel-1-DIMM-0".
TEST=Boot up with sarien platform and run dmidecode to check SMBIOS
type 17 have expected output.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie2125c0381bd24d96f725f68cde93a53da8c94c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Current SMBIOS type 17 device and bank locator string is like
"Channel-x-Dimm-x" and "Bank-x", x is deciminal number. Give silicon or
mainboard vendor a chance to replace with something matches with
silkscreen.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I54f7282244cb25a05780a3cdb9d1f5405c600513
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
GPIO pin GPP_C23 is used as level trigger but not edge trigger, also it
is not inverted, correct it here. According to board schematic, GPP_C23
connected with 3.3v pull up, so the pin is low active.
BUG=b:128554235
TEST=Boot up arcada platform with stylus keep on touching the screen,
the touch screen is still functional once in OS stage. Without change,
touch screen is not functional at same scenario.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I2bee664198057e3997dda181a16b9a0388067036
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32347
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The EC can return a board ID value similar to the Chrome EC.
In order to use this for the board version returned by SMBIOS
this commit implements the board_id() function for mainboards
that use this EC.
BUG=b:123261132
TEST=Check /sys/class/dmi/id/board_version to see that it
is reflecting the value that the EC provides.
Change-Id: I3fbe0dc886701f37d2424fe7a2867fd860fa1ec0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32276
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This progress code enables keyboard backlight control that
otherwise would only work 30 seconds after boot. This code
is already defined but it was not being sent by coreboot.
It is run in the "post device" step between the other defined
progress codes.
BUG=b:130754032
Change-Id: Ica6c622e568cb236c17bf3edb6639d0177510846
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Move the southbridge code to bd82x6x folder similar to the lynxpoint
implementation.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I8afc9f966033f45823f5dfde279e0f66de165e93
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Set default configuration to low for gpio_178, and can remove the
override setting for bobba/bloog/fleex/meep/phaser.
For ampton, Change-Id I64a67f73564188ad0548a1a770169ef2bca47453 (
mb/google/ampton: Fix polarity of EN_PP3300_WLAN_L signal.)
modified the pin setting.
TEST=verified that boot into OS on meep board.
suspend/resume, reboot, and no failure found.
Change-Id: I7668ff4817edfca5c6cea63db779fcea21c7af92
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32247
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ensures to follow Intel SDM Vol 3B Sec 18.7.3 to
calculate nominal TSC frequency.
As per SDM recommendation:
For any processor in which CPUID.15H is enumerated and
MSR_PLATFORM_INFO[15:8] (which gives the scalable bus frequency) is
available, a more accurate frequency can be obtained by using CPUID.15H
This patch also adds header file to capture Intel processor model number.
BUG=b:129839774
TEST=Boot ICL platform and calculate TSC frequency using below methods
1. TSC freq calculated based on MSR 0xCE
tsc: Detected 1600.000 MHz processor
2. TSC freq calculated based on CPUID 0x15
tsc: Detected 1612.800 MHz TSC
Method 2 actually reduce ~25ms of boot performance time.
Note: Method 2 is recommended from gen 6 processor onwards.
Change-Id: I9ff4b9159a94e61b7e634bd6095f7cc6d7df87c7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
GPT4 is a 32-bit timer and the counter of GPT4 will overflow in about
330 seconds (0xffffffff / 13MHz). Timer and delay functions will not
work properly if the counter overflows. To fix that we should use the
64-bit timer (GPT6).
BUG=b:80501386
BRANCH=none
Test=emerge-elm coreboot; emerge-kukui coreboot
Change-Id: I9f080e47253a1b1bab4636a45cb86c8666a25302
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Use common code to detect ACPI S3.
Tested on Lenovo T520 (Intel Sandy Bridge) with Change
I8afc9f966033f45823f5dfde279e0f66de165e93 applied as well.
Still boots to OS, no errors visible in dmesg and S3 resume is working.
Change-Id: I283a841575430f2f179997db8d2f08fa3978a0bb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Kukui is using MIPI display panel and needs some identifier to tell
payloads which LCD module is installed, and to select right kernel
device tree. Following Scarlet, the decision is to embed LCD module ID
as part of SKU ID.
The LCM ID is using a different voltage mapping table from the rest.
Considering the complexity in computation of SKU ID, it is better to
move the cache logic from get_index to caller.
Also revise the mapping table since ADC on 8183 only supports 12
levels.
BUG=b:129299873
TEST=make -j; boots on Kukui Rev2 unit.
Change-Id: Ib0c00bc8ce3c71c445c5c4561403ce8ef4dd5844
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32263
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
build.h provides iasl's version but right now assumes that it's kept in
util/crossgcc/xgcc/bin. Often true, but not always, so use the one found
in .xcompile to query the version as that's the version that is used in
coreboot builds.
Change-Id: Iaeedc22e0e14fa96b4f2a68127f405c7f0c9d5cc
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Martin Roth <martinroth@google.com>
With commit
'4074ce0cc7 (intel/apollolake: Add HDA to disable_dev function)'
FSP is now requested to switch off HDA PCI device if it is disabled in
devicetree. Doing so results in a warm restart. Normally this event
will be stored in CMOS RAM (if the descriptor is configured to do so)
and therefore no further resets are requested by FSP on the next boots
as long as CMOS RAM is kept alive.
The Siemens mainboards based on Apollo Lake do not have a CMOS battery
and therefore the CMOS is not backed up. This leads to reset requests
from FSP after PCI enumeration on every boot. To avoid this reset enable
HDA in devicetree for these mainboards. Though we do not have any usage
of HDA it should not be an issue that the HDA device is now enabled. The
benefit is though that no reset is requested anymore by FSP.
Change-Id: I637c7c01d73350700c6066fee74fecbb5b93b221
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32295
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the power rail discharge times measured on hatch,
update the assertions widths that have to be programmed in SoC.
BUG=b:129328209
TEST=warm/cold reboot and S3 are working fine on hatch.
Change-Id: I3c6dce0a942e6dcd9e55ef5e58a7e9e8d2b0a1e3
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add a common detect_s3_resume function.
Will be used by other southbridge code.
TODO: Merge with soc/intel/common/*/pmclib
Tested on Lenovo T520 (Intel Sandy Bridge) with Change
I283a841575430f2f179997db8d2f08fa3978a0bb applied as well.
Still boots to OS, no errors visible in dmesg and S3 resume is working.
Change-Id: I88023af522afac8164f068b0fbe0eac601aef702
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Restore Goodix devicetree config because of the
missing Goodix config when moving from baseboard
devicetree to board level overridetree. And move
PENH from I2C#2 to I2C#1.
BUG=b:124460799
BRANCH=None
TEST=local build and tested with Goodix touch screen
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic028c5d7b687a069d7f0510897bea91dca58e91f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Cannon Lake and family require that FSP-M component should be
XIP. This change selects FSP_M_XIP so that the right arguments are
passed into cbfstool when adding this component.
BUG=b:130306520
TEST=Verified that hatch boots fine to OS.
Change-Id: Ifd8a829ebdc7681c81ece4540aa38cdcea7b6fac
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This change uses GPIO IRQ instead of IOAPIC for GPP_A0 pad which is
the interrupt line for sx9310. This is required because IRQ# used by
GPP_A0 is allocated for PIRQ which does not allow IRQ# sharing.
Additionally, this change also configures GPP_A6 for GPIO IRQ. GPP_A6
is currently unused in the devicetree.
BUG=b:129794308
TEST=Verified that there are no interrupt storms on GPP_A0.
Change-Id: Ibb510a647391c0d9cb854d23656bb4b1cb7756ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change configures reset config for all pads routed to IOAPIC as
PLTRST. This is required to ensure that the internal logic of the GPIO
gets reset any time the platform enters S3 or powers off and avoids
any interrupt storms on boot-up.
BUG=b:129933011
TEST=Verified that there are no interrupt storms on boot-up from S5.
Change-Id: Ib790280c9f1410fa18746d4d7d2a5027afd7585b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Move Winbond M25PXX command values to spi_winbond.h
file.
The command values will be used for programming SPI
contoller of Intel Braswell, using this include file.
Update winbond.c file with coreboot header.
BUG=N/A
TEST=Facebook FBG-1701 with flashrom
Change-Id: I9c17c4ed7004209bd3c619d47a7474b0b7e17495
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
FSP code will default enable the onboard serial port.
When external serial port is used, this onboard port needs to be
disabled.
Add function mainboard_after_memory_init() function to perform
required actions to re-enabled output to external serial port.
BUG=N/A
TEST=LPC Post card on Intel Cherry Hill
Change-Id: Ibb6c9e4153b3de58791b211c7f4241be3bceae9d
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add the new configuration 'Krane' that will need at least its own EC.
There's currently no difference in coreboot side.
BUG=b:130011505
TEST=make menuconfig; make -j # select board=Krane
BRANCH=None
Change-Id: Ibb2ec42b08f9a51b22c22f3fe99b203f5eb31627
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Element Self Description register (ESD) [23:16] is R/WO, so let
write the ESD.CID when we start ich7_setup_root_complex_topology.
This value is also used to program the R/WO 'Target Component ID'
registers of RPxD and HHD.
Once it is done, no need to rewrite on them as they become RO.
(For more information, please see ICH7 datasheet page 271.)
Tested done on 945G-M4 using printk before and after writing.
Before this change, writing on those registers had no effect:
ESD: 0x0104: 0x00000802
ULD: 0x0110: 0x00000001
ULBA: 0x0118: 0x00000000
RP1D: 0x0120: 0x01000003
RP2D: 0x0130: 0x02000003
RP3D: 0x0140: 0x03000002
RP4D: 0x0150: 0x04000002
HDD: 0x0160: 0x0f000002
RP5D: 0x0170: 0x05000002
RP6D: 0x0180: 0x06000002
Using this patche, those R/WO get the "right" values.
i.e., We can see RCBA32(ULBA) is now equal to (uintptr_t)DEFAULT_DMIBAR.
ESD: 0x0104: 0x00020802
ULD: 0x0110: 0x01010001
ULBA: 0x0118: 0xfed18000
RP1D: 0x0120: 0x01020003
RP2D: 0x0130: 0x02020003
RP3D: 0x0140: 0x03020002
RP4D: 0x0150: 0x04020002
HDD: 0x0160: 0x0f020002
RP5D: 0x0170: 0x05020002
RP6D: 0x0180: 0x06020002
Change-Id: I3f2199d6da22ce9995496c2a81363710edde81f3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30993
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There will be an out of bounds read if the index is equal
to the array size. Fix the checks to exclude this case.
Found-by: Coverity Scan, CID 1347350, 1347351
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I5b4e8febb68dfd244faf597dfe5cdf509af7a2ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This implementation corrects the GPE DWx mapping for GPIO groups.
The assignments is done in GPIO MISCFG register for all GPIO communities.
And configures the which GPIO communities get register as Tier1.
BUG=b:121212459
TEST: Verified the GPIO MISCFG is getting set as per updated map.
Change-Id: I451997367025a6dc9e5931bd649524e935ad6aca
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32175
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The firmware is basically ignoring F11 and F12 without this change.
BUG=b:130143385
TEST=local compile and flash to device. Confirmed that press of F11 and F12
keys now generates appropriate keypress events (and the same codes that
are already generated by these keys on an external USB keyboard).
Signed-off-by: Matt Delco <delco@chromium.org>
Change-Id: Ic43114aa99fc0a1345782c81ed2b90f5569af383
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
WiFi enable signal was configured and driven as active-high, but the signal is |To start the server in this Emacs process, stop the existing
actually active-low
BUG=b:130196983
BRANCH=none
TEST=Verified WiFi still works after boot, and also after a suspend/resume cycle. Device powers down correctly using "poweroff".
Change-Id: I64a67f73564188ad0548a1a770169ef2bca47453
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32255
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Flashmap (FMAP) was not clearly documented. The new flashmap.md
explains where to find more details about that and how / why it was used
in coreboot. Also explained what is FMD and how to use it (based on
original README.fmaptool).
BUG=None
TEST=None (only documentation)
Change-Id: Ia389e56c632096d7c905ed221fd4f140dec382e6
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The value of "write protect" GPIO shall be read in depthcharge,
and the flag shall be set there instead.
BUG=b:124141368, b:124192753, chromium:1556855
TEST=Build locally
CQ-DEPEND=CL:1556855
BRANCH=none
Change-Id: I4d24a057b1385244a836a67c565ee6726a894fdc
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The "write protect" GPIO's cached value is never actually
read after entering depthcharge. Ensure the value from
get_write_protect_state() is being transferred accurately,
so that we may read this GPIO value in depthcharge without
resampling.
The cached value of the "recovery" GPIO is read only on certain
boards which have a physical recovery switch. Correct some of
the values sent to boards which presumably never read the
previously incorrect value. Most of these inaccuracies are from
non-inverted values on ACTIVE_LOW GPIOs.
BUG=b:124141368, b:124192753, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ic17a98768703d7098480a9233b752fe5b201bd51
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
For Kukui CR50_IRQ pin, we're going to replace external pull-up with
internal pull-up. This change won't break older boards, so we can just
always do that when setting up GPIOs.
BUG=b:124821269
BRANCH=none
TEST=Waveform looks correct.
Change-Id: Ib1a90dce583a6aa0cec8ac8ba96d1362f50c16a8
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This check had very few false positives which were all easily resolved,
and it's unlikely that further false positives will become problematic
in the future. On the other hand, it does detect a very severe bug (when
you think you're using a Kconfig but you aren't due to a typo), so since
warnings are currently not very visible, let's turn this into an error
because the pros clearly outweigh the cons for that.
Change-Id: I897b5e13d3242fb77b69f0bd3585baa7476aa726
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32257
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Now there is no need to additionally configure the FSP
before building;
- PEG works with high link speed 8 GT/s (Gen 3);
- external GPU supported, but dynamic switching between iGPU and PEG
is not yet supported.
Change-Id: Ie0f9db47c0b88052b090cba139f0ae821758935d
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31949
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Our strtol() and strtoull() function contain almost exactly the same
code. This is a) bad in general and b) may cause the code to get out of
sync, such as it recently happened with CB:32029.
This patch changes strtol() to be based on strtoull() so that the main
parsing code exists only once, and also adds a strtoll() to round off
the library. Also fix the bounds imposed by strtoul() to be based on the
actual length of a 'long', not hardcoded to 32-bits (which is not
equivalent on all architectures).
Change-Id: I919c65a773cecdb11739c3f22dd0d182ed50c07f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Our current limits.h only provides (U)INT_MAX constants. This patch adds
most others expected by POSIX. Since some of these may be different
depending on architecture (e.g. 'long' is 32-bit on x86 and 64-bit on
arm64), provide a definition that will automatically figure out the
right value for the data model the compiler is using (as long as it's
using two's complement for signed integers, which I think we can assume
these days).
Change-Id: I1124a41279abd4f53d208270e392e590ca8eaada
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
New compilers are a little more stringent about defining the same
prototype more than once, so some of our CONFIG_LP_DEBUG_MALLOC wrappers
don't quite work the way they are written anymore. Also, several of the
printf()s weren't written 64-bit safe. And let's add some
double-evaluation safety while I'm here anyway... and I have no idea why
this ever depended on CONFIG_LP_USB, that just seems like a typo.
Change-Id: Ib54ebc3cfba99f372690365b78c7ceb372c0bd45
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/14921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This pin should be set to its alternative function SRCLKENA0 instead of
GPIO, so that SPM (a power management component of MT8183) can control
it.
BUG=b:113367227
BRANCH=none
TEST=1. Boot. Run 'powerinfo' in EC console and see power state in S0.
2. Run 'powerd_dbus_suspend --wakeup_timeout=10', and then
run 'powerinfo' in EC console and see power state in S3.
3. Wait until AP resume.
4. Run 'powerinfo' in EC console and see power state back to S0.
Change-Id: I0a7e34f95381dec17eb6d166d6552c12e021bd9a
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32120
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a fmd file for 16MiB fmap, so that we can support
both 16MiB / 32MiB SPI flash ROM chips.
BUG=b:129464811
TEST=build hatch firmware image with 16MiB fmap and
verify fmap is updated by 'fuility dump_fmap'
Change-Id: Ifc0103c7fd0d99439f40a31d23422401a6dce826
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SMBIOS spec requires type 7 to be present.
Add the type 7 fields and enums for SMBIOS 3.1+ and fill it with the
"Deterministic Cache Parameters" as available on Intel and AMD.
As CPUID only provides partial information on caches, some fields are set to
unknown.
The following fields are supported:
* Cache Level
* Cache Size
* Cache Type
* Cache Ways of Associativity
Tested on Intel Sandy Bridge (Lenovo T520).
All 4 caches are displayed in dmidecode and show the correct information.
Change-Id: I80ed25b8f2c7b425136b2f0c755324a8f5d1636d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
lsbpos and msbpos have incorrect behaviour when given 0.
lsbpos(0) returns 8, and msbpos(0) hangs. The latter is
because the check i >= 0 is always true for an unsigned
integer, causing it to loop indefinitely (this was flagged
by Coverity).
0 doesn't have a lsb or msb position, so we change both
functions to return -1 in this case to indicate an error.
The code already guards against calling these functions
with 0, but we make this more explicit to prevent errors
in the future.
Found-by: Coverity Scan, CID 1347356, 1347386
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: Ic5be50846cc545dcd48593e5ed3fd6068a6104cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The SkipExtGfxScan option is defined in the device tree, but doesn`t
update the value in the UPD. It uses the default value - 0. This
means that the FSP will scan all external graphics devices, in spite
of the configuration in devicetree.cb for a specific board.
Patch updates SkipExtGfxScan options in UPD from devicetree.cb.
This change affects all boards with skl/kbl processor.
Change-Id: Ie88a41bdf31f7c3e88df6c70c82a1cbf866372c4
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Set new tcc_offset value to 10 degree C. This configures the Thermal
Control Circuit (TCC) activation value to 90 degree C. It prevents
any abrupt thermal shutdown while running heavy workload. This helps
to take early thermal throttling action when CPU temperature goes
above 90 degree C.
Change-Id: Ica77264782b4a3f3e72e73e1b8cb8b2e464fb033
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The effect of pointer aliasing on writes is that any data on CPU
registers that has been resolved from (non-const and non-volatile)
memory objects has to be discarded and resolved. In other words, the
compiler assumes that a pointer that does not have an absolute value
at build-time, and is of type 'void *' or 'char *', may write over
any memory object.
Using a unique datatype for MMIO writes makes the pointer to _not_
qualify for pointer aliasing with any other objects in memory. This
avoid constantly resolving the PCI MMCONF address, which is a derived
value from a 'struct device *'.
Change-Id: Id112aa5e729ffd8015bb806786bdee38783b7ea9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31752
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support PCIe Gen 3 with 8GT/s link speed for PEG x16
slot. All parameters for FSP are set during initialization in
romstage. Now there is no need to additionally configure the FSP
before building the ROM image.
Tested on Intel Core i5-6600 processor with the following devices:
- LP11000e Fibre Channel HBA (Gen2 x8);
- PEX8734 PCIe Fabric/Switch (Gen3 x16);
- NVIDIA GeForce GTX 1060 GPU (Gen3 x16).
GPU works with an nouveau and proprietary driver under Ubuntu 18.04.2
(4.15.0-46-generic GNU/Linux kernel). Discrete graphic card is used
as primary device for display output. Dynamic switching is not yet
supported.
Tianocore (edk2-stable201811-216-g51be9d0) is used as the payload.
Change-Id: Ia4f29df47d76de5069fe53120434cc7c2ab6f044
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31948
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP options list (for each PEG port):
- PegXEnable,
- PegXMaxLinkWidth,
- PegXMaxLinkSpeed,
- PegXPowerDownUnusedLanes,
- PegXGen3EqPh2Enable,
- PegXGen3EqPh3Method.
Add PegMaxLinkWidth to chip.h. This option overrides the number of
active lines from the devicetree.cb for each enabled PEG port (for
example for boards that use x4 instead of x16 lines in PEG0). If the
PegMaxLinkWidth is not defined, the port uses the maximum possible
number of lines.
To enable or disable the corresponding PEG root port you need to add
to the devicetree.cb:
device pci 01.0 on end # enable PEG0 root port
device pci 01.1 off end # do not configure PEG1
If PEG port is not defined in the devicetree, it will be disabled in
FSP.
It has been tested on ASRock H110M-DVS motherboard (Skylake i5-6600
CPU).
Change-Id: I23708f7060edf08739adf61fe61a419329907563
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32045
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The InternalGfx option in devicetree.cb is not used to enable iGPU.
The patch removes this option from chip.h and mb/*/devicetree.cb
files for all boards with skl/kbl processor.
Change-Id: I41ecca3fdfb1d4b20ee634a13263ff481dcf440e
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch includes the following changes:
1. Sets FSP options in romstage_fsp20.c to select primary GPU.
List of options:
- InternalGfx,
- PrimaryDisplay.
2. iGPU will be initialized if the corresponding PCI device is defined
in the device tree as:
device pci 02.0 on end
In this case, it is not necessary to set the InternalGfx option to
enable this device
3. Primary_iGFX is used as the default value for all skl/kbl boards
(since the PrimaryDisplay option isn`t defined in the devicetree.cb)
Change-Id: Ie3f9362676105e41c69139a094dbb9e8b865689f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
One of many steps to compile with -Wconversion, as unsigned int and int
aren't the same thing.
BUG=b:111443775
BRANCH=none
TEST=make junit.xml shows fewer warnings with -Wconversion enabled
Change-Id: I9673ca70da32a1e5117b27fa89167e03379af9c1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
RTC time contains invalid values on system without RTC battery.
Handle 'invalid' the same way as 'cmos_invalid'. This will reset CMOS date
when calling function enables 'invalid'.
BUG=N/A
TEST=Portwell PQ-M107 booting Linux Embedded
Change-Id: I5eae57d00f328400a8b03c28b7ecdbbc71522206
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29329
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I just got hit by a double-evaluation bug again, it's time to attempt
to fix this once more. Unfortunately there are several issues that don't
make this easy:
- bitfield variables don't support typeof()
- local macro variables that shadow others trigger -Werror=shadow
- sign warnings with integer literal and unsigned var in typeof-MIN()
- ({ statement expressions }) can not be used outside functions
- romcc doesn't support any of the fancy GCC/clang extensions
This patch tries to address all of them as far as possible with macro
magic. We don't have the technology to solve the bitfield and
non-function context issues yet (__builtin_choose_expr() still throws a
"no statement expression outside a function" error if it's only in the
branch that's not chosen, unfortunately), so we'll have to provide
alternative macros for use in those cases (and we'll avoid making
__ALIGN_MASK() double-evaluation safe for now, since it would be
annoying to do that there and having an alignment mask with side
effects seems very unlikely). romcc can continue using unsafe versions
since we're hopefully not writing a lot of new code for it. Sign
warnings can be avoided in literal/variable comparisons by always using
the type of the variable there. Shadowing is avoided by picking very
explicit local variable names and using a special __COUNTER__ solution
for MIN() and MAX() (the only ones of these you're likely to nest).
Also add DIV_ROUND_UP() to libpayload since it's a generally quite
useful thing to have.
Change-Id: Iea35156c9aa9f6f2c7b8f00991418b746f44315d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change moves the I2C/SPI devices and configs which do not apply
to all variants to override tree. Currently, there are just two
variants. However, as we prepare to add more variants, these devices
need to be moved out of the base devicetree.
BUG=b:129728235
TEST=Verified that I2C/SPI devices are present in static.c for hatch
and hatch_whl.
Change-Id: I9426f6bf5f8514de5f1889e22e57105749fd92de
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32138
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The patches added to `make` require that we use automake & aclocal
to rebuild the configuration, but version 1.15 of autotools is
expected. After debian sid updated to autotools 1.16, the tools can't
be located.
We'll just pretend to have version 1.15 with symbolic links. This
doesn't seem to be a good solution but gets the job done.
Change-Id: I9f616b96e728106e7adf321325caa06808e064c2
Signed-off-by: Martin Roth <martinr@coreboot.org>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28544
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In S3 the PCH is driving the DEVSLP signal low, assuming that the SATA device
is already powered off. However on hatch the SATA power is still enabled. And,
since DEVSLP is low, this causes the SATA device to not enter low power state.
The fix here is to set the pad config to be reset on PLTRST assertion which
will cause the pin to be high impedance state and will be pulled up by the
SATA device.
BUG=b:126611255
BRANCH=None
TEST=Make sure that S3 and S0ix is working fine on hatch.
And also make sure that DEVSLP is pulled high in S3.
Change-Id: Ifb6a71a72244522c8dd8d48e9b9f8dc6feef8981
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Serial IRQ was configured in quiet mode, but not enabled.
Enable serial IRQ and use 'enum seriirq_mode' as a devicetree
option.
Function sc_enable_serial_irqs() is added to enabled serial IRQs.
enable_serirq_quiet_mode() is renamed to
sc_set_serial_irqs_mode(). This function use the 'serirq_mode' to
set the mode. The call to this function is moved from finalize to init
having serial IRQs enable in early stage.
Serial IRQs must be enabled in continuous mode for at least one frame
before switching into quiet mode.
BUG=N/A
TEST=Portwell PQ7-M107
Change-Id: I7844cad69dc0563fa6109d779d0afb7c2edd7245
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
There's an issue with the newest toolchain that is blowing the bootblock
size on Smaug when compiling for chromeos. Increasing the bootblock
size by 2KB will take care of the issue for a while.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I58f7f1cedc8fc5b4c4287f5a120ed76140e1f7a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Adding Kohaku as a variant of hatch.
BUG=b:129706980
BRANCH=NONE
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
make sure HATCH_KOHAKU is built as well.
Change-Id: I5b451f421f6d353005e6b73eac180dcec2e8b0c0
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
When invoking 'make menuconfig' with gcc 4.9.2 an error is thrown:
ld: build/util/kconfig/lxdialog/checklist.o: undefined reference
to symbol 'acs_map'
This happens with ld version 2.24 and newer when menuconfig is
executed for the first time after make clean. This does not happen
with ld 2.20 (part of gcc 4.4.7).
It can be fixed with the flag -ltinfo in HOST_LOADLIBES.
Change-Id: I6216bb4d276d4bf98aa4ec06457b809fdcd73235
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If using a commit/branch which doesn't use a boot logo,
we don't want the build to fail unnecessarily
Test: build with upstream Tianocore commit hash,
avoid failure after successful compilation.
Change-Id: Ic41bacbb97926e9538f434aecc0f0eebc5f6326f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Skipping display init on normal-mode boot is a vboot feature, not
specific to Chrome OS. Fix the code in display_init_required() and
pci_dev_init() to check CONFIG_VBOOT rather than CONFIG_CHROMEOS now
that the two aren't always the same anymore.
Also add a check to guarantee at compile time that
CONFIG_VBOOT_OPROM_MATTERS is enabled on all platforms that make a check
to this function (when CONFIG_VBOOT is also enabled). The whole display
skipping mechanism is based on the oprom_needed NVRAM flag, and skipping
display init without enabling the option to tell vboot that it needs to
pay attention to that flag would make the whole thing not work right.
Change-Id: I5d6421509bdcdaa61b78015af3fa6241fe75bb7f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
GPP_A12 has a Native3 (SX_EXIT_HOLDOFF#) mode, which allows to delay
resuming to S0. If this pad is not locked and platform was not initially
designed for this functionality, malware could reconfigure this pads
setting under OS (switch to Native3), which would make platform not able
to resume until G3 is applied. To prevent misuse of this pad,
re-configure this pad before entering S3 and S5 to guarantee that the
pad configuration is correct.
BUG=b:128686027
Change-Id: I1e7979baa491acf2c56d223afb4618f0f6429e37
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch ensures to have same stack base for FSP and coreboot.
Feature added in FSP2.1
- Remove stack swapping from FSP.
- Stack will be shared between coreboot and FSP.
TEST=Build and boot FSP2.1 enable platform like dragonegg, iclrvp.
No car global variable corruption seen after enabling
this feature.
Change-Id: I673b4216d991d8ccad725c3931006a694184106c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32079
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Opens a binary file to extract DDR SPDs using known bits.
At the moment only DDR4 SPDs are supported.
Dumps the found SPDs into the current folder, as either
binary or hex encoded file.
Works with python2 and python3.
Change-Id: I26dd73d43b724ea6891bb5b6e96856c42db8577c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
The dead_code() macro can be used to ensure that a certain code path is
compile-time eliminated (e.g. if you want to make sure it's never
executed for certain Kconfig combinations). Unfortunately, the current
implementation via __attribute__((error)) hits only at the GCC level.
This can catch code that can be compile-time eliminated based on state
within the same file, but it cannot be used in cases where a certain
library function is built but then garbage collected at link time.
This patch improves the macro by relying solely on the linker finding an
undefined reference. Unfortunately this makes the error message a little
less expressive (can no longer pass a custom string), but it is still
readable and one can add code comments next to the assertion to
elaborate further if necessary
Change-Id: I63399dc484e2150d8c027bc0256d9285e471f7cc
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32113
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch enables CONFIG_VBOOT_OPROM_MATTERS in a few more cases where
I think(?) it should be. Haswell, Broadwell and Baytrail Chromebooks
have this enabled in their old depthcharge firmware branches -- we
presumably just forgot to move it over when vboot2 migrated the option
to coreboot. Braswell didn't, but it seems like this requirement was
added when it was migrated to FSP 1.1...? (Not very sure about that one,
but it does call load_vbt() right now which executes things based on
display_init_required().) Additionally, it seems to make sense to enable
it whenever the user explicitly selects VGA_ROM_RUN in menuconfig (like
one of the Intel defconfigs does).
Once we have all this, one could take a step back and ask whether this
option still makes sense at all anymore. It's enabled for almost all
devices (that work with vboot at all), it will presumably be enabled for
all future devices, and it seems that most devices that don't enable it
use libgfxinit, which as far as I can tell isn't gated on
display_init_required() but probably should be. Realistically, whatever
kind of display init a board needs to do (native or option ROM), it's
probably expensive enough that it's worth skipping on a normal mode
vboot boot, and we'd want to have this enabled by default on everything
except boards that actually don't have a display. So maybe we should
flip it around to CONFIG_VBOOT_OPROM_DOESNT_MATTER, but doing that would
probably lead to nobody ever selecting it at all.
Not sure what the best solution there is yet, but I think this patch
at least moves things in the more correct direction.
Change-Id: Id96a88296ddb9cfbb58ea67d93e1638d95570e2c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add bluetooth Rfkill function to recover the Bluetooth controller in
cases where itself has entered a bad state and needs to be recovered.
Bug=b:129375810
TEST=Boot up into OS and dump SSDT table, check there's _DSD entry under
Bluetooth devices with GPIO in. Also confirm bluetooth itself is
functional.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I79a310a55d94d7d20d1705afc11fe47cbb81abc1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
GPP_A12 is being used as FPMCU_RST in hatch. This GPIO is being padlocked in
FSP and cannot used in kernel. Hence unlock the GPIO pads to export this pin
in kernel to be used as FPMCU_RST.
BUG=b:128686027
BRANCH=None
TEST=Read Pad Configuration Lock (PADCFGLOCK_GPP_A_0) register.
localhost /sys/class/gpio # iotools mmio_read32 0xfd6e0080
0x00000000
localhost /sys/class/gpio # echo 212 > export
Change-Id: Ie0439956e6c8e386435e535665ccaf2ab82adeb0
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32126
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP has a UPD to unlock all GPIO pads. This parameter is disabled by
default. Add a chip parameter so that GPIO pads can be unlocked on mainboard
level in devicetree and therefore this feature can be used if needed.
BUG=b:128686027
Change-Id: Iad9e8a209dc3f8ca0c994e8c1da329918409a1d4
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Ignore integrated GBE controller LTR setting to make it wake up from
s0ix with 10/100M cable attached.
BUG=b:122435844
TEST= Test on sarien platorm, after the changes sytem can wake by WOL,
and also checked SLP_S0 residency can increase with 10/100M cable
and battery connected.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Iec7dd197b8a456751f8e4dcb19e3e153f5888613
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Deassert EN_PP3300_WWAN to turn the WWAN module completely off when
entering S5. This is the same fix in commit eeb475c5c for coral board.
BUG=none
BRANCH=none
TEST=On hatch, Perform a quick system power cycle, verify that the modem
is powered cycle and the SIM with PIN lock enabled requests unlocking.
Change-Id: I3ec8ccb7618189b9e8586f5571a68d3309597ee7
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch ports CB:30717 changes from CNL to ICL.
This structure is declared as a static CAR_GLOBAL in the common
PMC library code and in the SOC specific code. Remove the SOC
specific version and instead get the chipset_power_state pointer
from the PMC library.
This fixes events that were recorded in chipset_power_state at
boot but were reading as all zero when it was time to parse the
structure when logging events to flash.
Change-Id: I1152d0e882e1acf475072d1553b74f9161e2f485
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32095
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I added a method to fill out the _BIX package structure but never
hooked it up to the expected _BIX method that the OS uses.
This change adds _BIX method and uses the existing method to fill
it out. It also adds ^ before the _UID in _BIF to match _BIX as
the _UID is one level above the method.
Change-Id: I0de91369b6780fd9432990732c1078a73f6a3419
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
When in romstage call into the EC init function so it can send a
progress code to the EC before memory training starts.
BUG=b:127875364
TEST=boot with FSP debug and ensure EC does not try to turn off the
system while it is still booting.
Change-Id: I5d99fb16bae250a82b652c530c13977e74c3378b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
When using FSP with debug enabled it takes too long to get to ramstage
and send the first progress code to the EC. The same thing has been
reported to happen when 2x16GB memory is installed.
BUG=b:127875364
TEST=boot with FSP debug and ensure EC does not try to turn off the
system while it is still booting.
Change-Id: I5676354f5e53540273a9029411507f91864735a1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
As part of chromium:942901, physical dev switch functionality
is being deprecated.
Remove remaining references as well as helper macros.
BUG=chromium:942901
TEST=Build locally
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ib4eec083eb76d41b47685701f9394c684ddc6b37
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The policy to identify and log the XHCI wake events is similar between
skylake and apollolake. Hence move the similar parts to a common
location.
BUG=b:123429132
BRANCH=None
TEST=Ensure that the system boots to ChromeOS. Ensure that the wake up
events due to USB are logged into the event logs.
6 | 2019-03-21 09:22:18 | S0ix Enter
7 | 2019-03-21 09:22:22 | S0ix Exit
8 | 2019-03-21 09:22:22 | Wake Source | PME - XHCI (USB 2.0 port) | 9
9 | 2019-03-21 09:22:22 | Wake Source | GPE # | 13
10 | 2019-03-21 09:23:20 | ACPI Enter | S3
11 | 2019-03-21 09:23:30 | Wake Source | PME - XHCI (USB 2.0 port) | 9
12 | 2019-03-21 09:23:30 | ACPI Wake | S3
13 | 2019-03-21 09:23:30 | Wake Source | GPE # | 13
Change-Id: Ia6643342e3292984e422ff3c3fcd4bc0d99f947e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In the latest hatch schematics, BOOT1 for the FP MCU is now connected
to the AP. Configuring it to be the same as BOOT0.
BUG=b:126455006
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a -c max
Change-Id: Ibb451983674a7d812dc562cb8addb1dc50fb155c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The following is the FSP logic: as long as the Cpu Ratio input in
coreboot is different with CpuStrapSet, system will force to follow
input from coreboot. But CpuStrapsetting is floating, it will be 0
from the first cold boot before memory training and set to 0x1c (or
max CPU ratio for the installed CPU) after first memory training.
The previous fix was attempting to ensure settings were cleared
when FSP was called in recovery mode, but only when coming from S5
which caused issues if recovery mode is requested by the OS and
is only followed by a warm reset.
BUG=b:129412691
TEST=Boot up sarien platform and force recovery, check there's no reset
in the path of recovery.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I959188be46343bc6f2cb3cc149097b4d449802aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32089
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set tcc_offset value to 10C. It configures the Thermal Control Circuit (TCC)
activation value to 90C. This prevents any abrupt thermal shutdown by taking
early thermal throttling action when CPU temperature goes above 90C.
Change-Id: Ifee0fcc326530622b04e60af0f3b9cb9e3aea7ea
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31984
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For systems that integrate GbE controllers, following parameters should be configured:
SlpS0WithGbeSupport: enable PchPmSlpS0VmRuntimeControl: disable,
PchPmSlpS0Vm070VSupport: disable, PchPmSlpS0Vm075VSupport: disable.
TEST=boot on any GbE supported WHL platform
Change-Id: I02aaf0b77b8fc1555a3a424c02acfada21707d0e
Signed-off-by: Krzysztof Sywula <krzysztof.m.sywula@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The edid variable was being dereferenced before the null check. Split
off the null check to before dumping and update the error message.
Fixes CID 1370576 (REVERSE_INULL)
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I8fe3d911df3a11a873056d3a5c05c5a3cbcfe2c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Remove bip, as it is no longer actively developed, and its EC
overflowed storage, so the EC build is no longer viable.
BUG=b:129283539
BRANCH=none
TEST=emerge-octopus coreboot chromeos-bootimage
CQ-DEPEND=CL:1538819,CL:*1086038
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: Ie9ffa704af3523908858d382e2c188422323550e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Instead of manually filling out the lb_gpios struct,
use the newer lb_add_gpios notation, which is more
compact and less error-prone.
BUG=b:124141368
TEST=util/lint/checkpatch.pl -g origin/master..HEAD
TEST=util/abuild/abuild -B -e -y -c 50 -p none -x
BRANCH=none
Change-Id: I90795f32be5de881c94519933f36127098c184df
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32031
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As part of chromium:942901, physical dev switch functionality
is being deprecated.
This flag is no longer read after CL:1526070, and thus
does not need to be set here.
coreboot's vboot subrepository needs to be updated to include
CL:1526070 before this CL can be merged.
BUG=b:124141368, b:124192753, chromium:942901
TEST=Build and deploy to eve
TEST=util/lint/checkpatch.pl -g origin/master..HEAD
TEST=make clean && make test-abuild
CQ-DEPEND=CL:1526070
BRANCH=none
Change-Id: Ie5849f9e0fcb8e4e6d35d542a141bf635e751af4
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31952
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently only two devices make use of physical dev switch:
stumpy, lumpy
Deprecate this switch. If these devices are flashed to ToT,
they may still make use of virtual dev switch, activated
via recovery screen.
BUG=b:124141368, b:124192753, chromium:942901
TEST=util/lint/checkpatch.pl -g origin/master..HEAD
TEST=util/abuild/abuild -B -e -y -c 50 -p none -x
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I87ec0db6148c1727b95475d94e3e3f6e7ec83193
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31943
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
strtoull() can optionally take a second pointer as an out-parameter that
will be adjusted to point to the end of the parsed string. This works
almost right, but misses two important edge cases: firstly,when the
parsed string is "0", the function will interpret the leading '0' as an
octal prefix, so that the first actually parsed digit is already the
terminating '\0' byte. This will cause the function to early abort,
which still (correctly) returns 0 but doesn't adjust *endptr.
The early abort is pointless anyway -- the only other thing the function
does is run a for-loop whose condition is the exact inverse (so it's
guaranteed to run zero iterations in this case) and then adjust *endptr
(which we want). So just take it out. This also technically corrects the
behavior of *endptr for a completely invalid string, since the strtoull
man page says
> If there were no digits at all, strtoul() stores the original value of
> nptr in *endptr (and returns 0).
The second issue occurs when the parsed string is "0x" without another
valid digit behind it. In this case, we will still jump over the 0x
prefix so that *endptr is set to the first byte after that. The correct
interpretation in this case is that there is no 0x prefix, and instead a
valid 0 digit with the 'x' being invalid garbage at the end. By not
skipping the prefix unless there's at least one valid digit after it, we
get the correct behavior of *endptr pointing to the 'x'.
Change-Id: Idddd74e18e410a9d0b6dce9512ca0412b9e2333c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This option has been relocated to depthcharge:
https://crrev.com/c/1524806
BUG=b:124141368, b:124192753
TEST=Build and deploy to eve
TEST=util/lint/checkpatch.pl -g origin/master..HEAD
TEST=util/abuild/abuild -B -e -y -c 50 -p none -x
TEST=make clean && make test-abuild
CQ-DEPEND=CL:1524806
BRANCH=none
Change-Id: Ib4a83af2ba143577a064fc0d72c9bc318db56adc
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31909
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch cleans up remaining uses of raw boolean Kconfig values I
could find by wrapping them with CONFIG(). The remaining naked config
value warnings in the code should all be false positives now (although
the process was semi-manual and involved some eyeballing so I may have
missed a few).
Change-Id: Ifa0573a535addc3354a74e944c0920befb0666be
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The prev_sleep_state value was showing 5 even after warm reboot, once the
SUS_PWR_FLR bit is being set. This bit was not being cleared.
Hence clearing the PMCON status bits.
BUG=b:128482282
BRANCH=None
TEST=In cbmem logs, check for value of “prev_sleep_state” using command
cbmem –c | grep “prev_sleep_state”
For cold reboot, "prev_sleep_state 5"
For warm reboot, "prev_sleep_state 0"
Change-Id: If9863d52ed3c61b6a160df53f023b0787eaaed68
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
gale has a button which is essentially used as a
"physical presence" button. Its only use is to emulate
^D or ^U on boot when the button is pressed.
(See depthcharge src/board/gale/board.c)
Previously (and currently in CrOS firmware branch) this
GPIO was defined as the physical developer switch,
and read as such in depthcharge. It was removed in
cleanup patch CB:18980.
Add the GPIO back as physical presence ("presence"),
which will be read by depthcharge in CL:1532492.
BUG=b:124141368, b:124192753, chromium:942901
TEST=util/lint/checkpatch.pl -g origin/master..HEAD
TEST=util/abuild/abuild -B -e -y -c 50 -p none -x
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ic144f839b7f9933d573db8f84c4bf5905eea96f6
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The TPM driver isn't loaded in other stages but verstage so when we try
to communicate with the TPM it fails. We don't need to communicate with
it anyway since the TPM won't continue to tell us that recovery was
requested, only the first query responds with the recovery request.
BRANCH=none
BUG=b:129150074,b:123360379
TEST=1)boot arcada without recovery and notice that the "tpm transaction
failed" log lines are no longer present. 2) boot into recovery using the
ESC refresh power key combination and verify that the recovery reason
was "recovery button pressed"
Change-Id: I13284483d069ed50b0d16b36d0120d006485f7f4
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Keith Short <keithshort@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
mainboard users can select correct MP Init Kconfig in order to
perform MP initialization.
1. Native coreboot MP Init.
2. FSP to do MP Init.
3. FSP to make use of coreboot MP service PPI to perform MP Initialization
Change-Id: Ifbea463fdaf97d68c21a759c37f49492d58a056b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
We have more test data now so update the DPTF accordingly.
* Change passive temp to 50/57/55/52 C
* Change critical temp to 75C
* All interval to 20 secs
BUG=b:113101335
TEST=temp/perf looks better in thermal chamber test.
Change-Id: I872c3f1875d0cbac148c44c449954e6871c9d0b0
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change enables user to shutdown the system by shortly pressing
power button (<10sec) before OS is loaded. Main use case is shutdown
from recovery/broken screen.
BUG=N/A
TEST=Boot up into recovery screen on Sarien platform, press power button
once, and system should shutdown immediatelly.
Change-Id: I7655daf65ff058df7d9bad4567f74b4f4007acb4
Signed-off-by: Krzysztof Sywula <krzysztof.m.sywula@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
AP communicates with FP MCU through gspi1.
BUG=b:126455006
BRANCH=None
TEST=ensure during bootup we see spi id spi-PRP0001:01 in dmesg
FP MCU fw is not ready yet, so not much testing to be done yet.
Signed-off-by: Shelley Chen <shchen@google.com>
Change-Id: I2eba205d5e63664dca684fbd849454c5a2fe0d0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32017
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add SAR0, which is an SX9310. The schematics and layout have a second
SAR1 sensor provisioned on I2C4, with an interrupt of GPP_A6, but this
is not populated.
Signed-off-by: Evan Green <evgreen@chromium.org>
BUG=b:128540461
BRANCH=none
TEST=Boot kernel with sx9310 driver, see it come up happily
Change-Id: I63943cc7da5ff56f6ef6dcbd99bb8f8f031e8bf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable the HUNG_TASK as a wakeup host event, as it's used by S0ix failure
detection to wake the system back up if a suspend to S0ix never
asserted S0_SLP#.
BUG=b:123716513
BRANCH=None
TEST=Test S0ix on Hatch with appropriate EC and kernel changes.
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: I447211892df210af97e8df0380bab032b14cbee8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32004
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch changes a few more Kconfig linter warnings to errors that
currently do not show up in the tree and that seem unlikely to become
false positive in the future. One instance of duplicated code that
essentially checks for the same thing was consolidated.
It also adds a new test for references to boolean Kconfig options that
do not use the CONFIG() wrapper macro. It's a little flaky (e.g. hard to
handle multi-line comments), but it should be helpful the majority of
the time as a warning in a Jenkins comment.
Change-Id: I975ee77d392ed426f76f7671d9b6ef9441656e6a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Depthcharge is changing how the RW_LEGACY CBFS is handled for alternate
bootloaders, see https://crrev.com/c/1528550 and
https://crrev.com/c/1530303. This means that RW_LEGACY must be marked as
CBFS in the fmap in order to work. All boards except for kahlee(grunt)
have CBFS marked.
BUG=b:128703316
TEST=Build and ran on grunt along with chromium patches on grunt and was
able to list alternate bootloader with ctrl+l
BRANCH=none
Change-Id: I843d565a9503d27e666a34e59aba263ec490c81f
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32019
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previously, the size of memory made for vboot_working_data
through the macro VBOOT2_WORK was always specified in each
individual memlayout file. However, there is effectively no
reason to provide this customizability -- the workbuf size
required for verifying firmware has never been more than 12K.
(This could potentially increase in the future if key sizes
or algorithms are changed, but this could be applied globally
rather than for each individual platform.)
This CL binds the VBOOT2_WORK macro to directly use the
VB2_WORKBUF_RECOMMENDED_DATA_SIZE constant as defined by vboot
API. Since the constant needs to be used in a linker script, we
may not include the full vboot API, and must instead directly
include the vb2_constants.h header.
BUG=b:124141368, b:124192753
TEST=Build locally for eve
TEST=util/lint/checkpatch.pl -g origin/master..HEAD
TEST=util/abuild/abuild -B -e -y -c 50 -p none -x
TEST=make clean && make test-abuild
BRANCH=none
CQ-DEPEND=CL:1504490
Change-Id: Id71a8ab2401efcc0194d48c8af9017fc90513cb8
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Assign the FSP UPDs for HPD and DDC of DDI ports. FSP assumes that all
DDI ports are enabled and hence configures the HPD and CLK for DDI ports.
This patch initializes only the required UPDs to enable display ports.
BUG=b:123907904
TEST=DP devices working correctly.
Change-Id: Ic0c172cd3d087fc8f49b01ab23feffdababf7166
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds generic log to perform subsystem programming
based on header type.
Type 0: subsystem offset 0x2C
Type 2: subsystem offset 0x40
Type 1: Read CAP ID 0xD to know cap offset start, offset 4 to locate
subsystem vendor id.
Change-Id: Id8aed6dac24517e93cd55d6bb3b254b7b4d950d3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: David Guckian
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch will fix these checkpatch errors in src/arch/mips/.
- src/arch/mips/ashldi3.c:22: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
- src/arch/mips/bootblock_simple.c:35: WARNING: braces {} are not necessary for any
arm of this statement
Change-Id: Ic859913b93dc8ed6ff64b551c8a6baf72d28c75a
Signed-off-by: Asami Doi <d0iasm.pub@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This reverts commit 51169b7dda4a1978d622e329a1c40e384471c165.
I was not ready to enable this option yet, until it is enabled
in depthcharge it needs to stay off in coreboot or depthcharge
will attempt to do software sync without a proper driver.
Change-Id: I4840812d0541f822502cfc5c66bed27edf4d2ecc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32007
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To support both boards with the same firmware add a SKU for
each variant that is used to include the proper EC firmware
image to match what the EC is expecting.
BUG=b:119490232
TEST=tested by faking the EC response to ensure that the OS
and firmware update tools are able to determine the correct
model based on the value returned by the EC.
Change-Id: Iaa677975e0bccbee5ec8a39821fe1637f08270fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This will be used to distinguish the mainboard SKU so that the
correct EC firmware can be bundled with the board.
This is read from EC RAM so it can be used by an ACPI method in
the future.
BUG=b:119490232
Change-Id: I71b8017fc4b88e793dfe709e1cb1ab0f0bcdc4fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Commit 41483c9 (soc/intel/cannonlake: Add required FSP UPD changes for
CML) changed the enum values for PCH_SERIAL_IO_MODE so that 0 is
invalid and valid values start from 1. However, get_param_value was
not updated to correctly subtract 1 before returning any value. This
change adds a macro PCH_SERIAL_IO_INDEX to apply the subtract 1
operation on any value that get_param_value needs to return.
BUG=b:128946016
TEST=Verified that hatch boots successfully.
Change-Id: I4e32fcd1efe4a535251f0ec58662a2dc5f70e8b0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Create a new cbtable entry called VBOOT_WORKBUF for
storing a pointer to the vboot workbuf within the
vboot_working_data structure.
BUG=b:124141368, b:124192753
TEST=Build and deploy to eve
TEST=util/lint/checkpatch.pl -g origin/master..HEAD
TEST=util/abuild/abuild -B -e -y -c 50 -p none -x
BRANCH=none
Change-Id: Id68f43c282939d9e1b419e927a14fe8baa290d91
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31887
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support for FSP2.1 Kconfig which is backward compatible
with FSP2.0 specification and added below coreboot impacted features as below:
1. Remove FSP stack switch and use the same stack with boot firmware
2. FSP should support external PPI interface pulled in via
FSP_PEIM_TO_PEIM_INTERFACE
Change-Id: I2fef95a783a08d85a7dc2987f804a931613f5524
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30310
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ensures to have below listed features:
1. All required APIs to create MP service structure.
2. Function to get MP service PPI status
MP specification here:
http://github.com/tianocore/edk2/blob/master/MdePkg/Include/Ppi/MpServices.h
coreboot design document here:
../Documentation/soc/intel/icelake/MultiProcessorInit.md
Supported platform will call fill mp_services structure so that FSP can
install the required PPI based on coreboot published structure.
BRANCH=none
BUG=b:74436746
TEST=Able to publish MP service PPI in coreboot.
Change-Id: Ie844e3f15f759ea09a8f3fd24825ee740151c956
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25634
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
RK3399 SoC code still manually excludes the BL31 region from the memory
map, even though that is now automatically done with the BL31()
memlayout region. CB:31123 and CB:31538 just forgot to remove this line.
The resulting memory map stays the same.
Change-Id: I87458fa09f437b038af10e0fd9d76ef6d9394bc5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ting Shen <phoenixshen@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This board is compatible with Intel Skylake and Kaby Lake generation
processors. This patch contains the minimum configuration for booting
and stable operation of the Ubuntu OS (18.04.1, Linux kernel 4.15).
It is based on Intel RVP8 mainboard.
Intel Kaby Lake FSP 3.6.0 is used to initialize CPU and PCH.
Graphics init with libgfxinit.
Works:
- Integrated graphics (only DVI port, tested with 1920x1080);
- PEG x16 (FSP must be configured with BCT to enable PEG);
- all PCIe x1 slots;
- all USB and SATA ports;
- SuperIO COM port for console;
- onboard audio.
TODO:
- other SuperIO functions;
- onboard network chip;
- suspend and resume;
- documentation.
Tested on Intel Core i5-6600 processor with Seabios (rel-1.12.0-10-
g171fc89) and Tianocore/edk2 (vUDK2018-8-ge6eccfc) as a payload.
Change-Id: I69396edc50948cf1d0da649241ce92171d32daf7
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The mmio resouces IOAPIC and ROM area not reserved.
Reserve IOAPIC and ROM resources.
BUG=N/A
TEST=Intel CherryHill CRB booting Embedded Linux
Change-Id: I917c30892b46ac1d964e7bab339082d17a1e706d
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
coreboot have an option to use legacy UART or LPSS UART. FSP will use the
UART initialized by coreboot and we can choose an option to skip Uart
initialization by FSP.
For this, we need to pass correct debug interface flag to FSP through
which FSP will know which UART port to use. If we don't pass correct
interface information, FSP may try to dump logs on that port and it may
slow down the system.
BUG=none
BRANCH=none
TEST=Compile and boot with coreboot. Check FSP and coreboot logs are
coming on serial port.
Change-Id: I1ebb20c93e2c15ec085538509099de72bc9dd62c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable software sync by default if VBOOT is enabled.
The slow update option is also needed, but this is moving
to depthcharge so it is not defined here.
Change-Id: I046661fae7315f84e96293532b4e1568558df962
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
If the command does not respond the driver should not wait for
it to complete before returning.
Tested with SMI debug enabled to ensure that the final command
does not report a failure.
Change-Id: I7c1bfa19a92e8332ac1aa6ff95f94ff4cbdf789d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update the Kconfig option for disabling ESPI SMI source
to disable it entirely, not just when ACPI mode is disabled.
For the situations where this is needed (just the sarien
board) it is better to completely stop the EC from sending
any SMI events as no actions are taken.
Change-Id: Id94481bb2f0cfc948f350be45d360bfe40ddf018
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add bluetooth Rfkill function to recover the Bluetooth controller in
cases where itself has entered a bad state and needs to be recovered.
Bug=b:123342945
TEST=Boot up into OS and dump SSDT table, check there's _DSD entry under
Bluetooth devices with GPIO in.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibbe67887227af42b6c040deade7bf5da4ce3227f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds required FSP UPD changes for CometLake SoC.
Also this patch tries to create common parse logic for CometLake as
well as cannonlake SOC.
We parse device tree parameters for PCI devices and fill values in FSP
UPDs. We fill UPDs based on pci device config as well as SerialIoDev
config of devicetree.
For PCI devices, if PCI device is disabled from devicetree, we'll assign
disable value to FSP UPD.
In case devicetree doesn't fill this parameter or value is invalid in
SerialIoDev config, default mode will be set to PCI.
In case of valid value, we'll fill the same value into FSP UPD.
BUG=none
BRANCH=none
TEST=check if CML board boots and proper UPD values are filled.
Change-Id: Ib92b660409ab01d70358042b2ed29b8bf9cab26d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
In the current state of the tree we do not utilise the
mechanism of having per-device overrides for PCI bus
ops.
This change effectively inlines all PCI config accessors
for ramstage as well.
Change-Id: I11c37cadfcbef8fb5657dec6d620e6bccab311a4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This reverts commit 626ba097a2.
This change was submitted under the incorrect assumption that there was
agreement on a coding style change. There wasn't, so while the issue is
under discussion we should revert to the previous status quo.
Making clang-format honor the line length is a separate issue from
changing the line length, and can be reuploaded as a separate CL.
Change-Id: I433c82c95a897b3113cace3668cc8ce0f1ab75bf
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit b3a8cc54db.
This change was submitted under the incorrect assumption that there was
agreement on a coding style change. There wasn't, so while the issue is
under discussion we should revert to the previous status quo.
Change-Id: I37a5585764346af11a98bdf58c810dd3cf5bfe40
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When VBOOT_STARTS_IN_BOOTBLOCK is selected, the tpm_setup call
in memory_init.c is not used.
When VBOOT_STARTS_IN_ROMSTAGE is selected, the tpm_setup call
in memory_init.c is triggered. However, when verstage runs,
tpm_setup is called yet again, and an error is triggered from
the multiple initialization calls.
Since there are currently no boards using
VBOOT_STARTS_IN_ROMSTAGE + FSP2_0_USES_TPM_MRC_HASH, disable
this combination via Kconfig, and remove the tpm_setup call
from Intel FSP memory initializion code.
* VBOOT=y VBOOT_STARTS_IN_BOOTBLOCK=y
vboot is enabled, and TPM is setup prior to Intel FSP memory
initialization. Allow FSP2_0_USES_TPM_MRC_HASH option.
* VBOOT=y VBOOT_STARTS_IN_BOOTBLOCK=n
vboot is enabled, but TPM is setup in romstage, after Intel
FSP memory initialization. Disallow FSP2_0_USES_TPM_MRC_HASH
option.
* VBOOT=n
vboot is disabled. Disallow FSP2_0_USES_TPM_MRC_HASH option.
See bug for more information:
https://bugs.chromium.org/p/chromium/issues/detail?id=940377
BUG=chromium:940377
TEST=util/lint/checkpatch.pl -g origin/master..HEAD
TEST=util/abuild/abuild -B -e -y -c 50 -p none -x
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I4ba91c275c33245be61041cb592e52f861dbafe6
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31837
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CNL PCH has PWR_FLR, SUS_PWR_FLR and HOST_RST_STS bits in GEN_PMCON_A
and so this change updates the check for these bits to use GEN_PMCON_A
instead of GEN_PMCON_B.
BUG=b:128482282
TEST=Verified that prev_sleep_state is reported correctly when booting
from S5.
Change-Id: I75780a004ded8f282ffb3feb0cdc76233ebfd4f2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31908
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To ensure the power button functions as expected in firmware ensure
that the EC is not in "S0ix supported OS" mode and expecting the
power button to be handled by the virtual button interface.
BUG=b:128409889
TEST=Verify that the power button works at the developer screen
when the system is rebooted from within Chrome OS. Also ensure
that it works when external warm reset signal is asserted by H1.
Change-Id: Ic323515e3b8be08bac4f0f82e25f2f78c2f22833
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Symbols prefixed with vb2_ should be reserved for internal
vboot library use.
Anything outside of that may choose some other prefix.
Here, we choose vboot_ instead.
Also, add some documentation to security/vboot/misc.h,
which provides headers for a number of different C files.
BUG=b:124141368
TEST=Build and deploy to eve
TEST=util/lint/checkpatch.pl -g origin/master..HEAD
TEST=util/abuild/abuild -B -e -y -c 50 -p none -x
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I5d9154fd2d5df25ee254bd5ce4a173afaa6588be
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31886
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Values from
- Intel doc 337347 rev4
- coreboot soc/intel/cannonlake/include/soc/gpio_soc_defs_cnp_h.h
On Coffeelake H (using Cannonlake / Cannonpoint PCH) p2sb is not
accessible. Using a static value instead. 0xfd000000 is a common value
chosen by coreboot and non-coreboot firmware.
Change-Id: Id637f703ab0a99eb0908ecdc3da27ba80db1c6b8
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
A side effect of the change 8e0dca05
"util/amdfwtool: Add generic image copy function"
was to treat a read operation of zero bytes as a failure. Some
implementations exist that use zero length files as a means of
removing functionality. This causes amdfwtool to exit with an
error.
Put the zero length capability back in, and generate the requested
table entry with a length field of 0x0.
TEST=Boot google/grunt, inspect PSP directory table
BUG=b:128507639
Change-Id: Ifc9204dbbf6b107f06116362358ab9d22caa71df
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31891
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In case PCI_IO_CFG_EXT=n parameter 'reg' was not
properly truncated to 8 bits and it would overflow
to dev.fn part of the register.
A similar thing could happen with 'dev' but that
value originates from PCI_DEV() macro unlike 'reg'.
Change-Id: Id2888e07fc0f2b182b4633a747c1786e5c560678
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31847
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For platforms that do not employ VBOOT_STARTS_IN_ROMSTAGE,
vboot verification occurs before CBMEM is brought online.
In order to make vboot data structures available downstream,
copy vb2_working_data from CAR/SRAM into CBMEM when CBMEM
comes online. Create VBOOT_MIGRATE_WORKING_DATA config
option to toggle this functionality.
BUG=b:124141368, b:124192753
TEST=Built and deployed on eve with STARTS_IN_BOOTBLOCK
TEST=Built and deployed on eve with STARTS_IN_ROMSTAGE
TEST=util/lint/checkpatch.pl -g origin/master..HEAD
TEST=util/abuild/abuild -B -e -y -c 50 -p none -x
BRANCH=none
Change-Id: I62c11268a83927bc00ae9bd93b1b31363b38e8cf
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Updating from commit id 1e177741:
2019-02-14 05:27:16 -0800 - (vboot: rename VB2_DISABLE_DEVELOPER_MODE)
to commit id 304aa429:
2019-03-12 10:38:56 -0700 - (futility: updater: Unit test for preserving sections using FMAP flags)
This brings in 18 new commits.
Change-Id: Ie2889ed0217c38734eb2c496ca20f95b6a12b102
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31872
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
By design only 'reg' parameter can have the two least-
significant bits set. As 'reg' is often a constant,
'0xCFC + (reg & 3)' resolves to an immediate value
already at buildtime, unlike (addr & 3) which depends
of a constant (but non-immediate) value of 'dev' in
ramstage.
Change-Id: I6e729fe800c92b1ce4994ad2b4203072fa75a958
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31754
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
From doc#573387 CML System Memory DQ DQS Rcomp Mapping Information
User Guide, RCompResistor[0] should be 121.
BUG=b:122959294
BRANCH=None
TEST=emerge coreboot and make sure boots up
Change-Id: If69e7fb41e79d88d21b0e50fb65107a1686d696a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31868
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MEM_CH_SEL is used to indicate whether we are on a single or dual
channel device, where MEM_CH_SEL = 1 for single channel skus and
MEM_CH_SEL = 0 for dual channel skus. Initialize single_channel field
(from GPP_F2), which will in turn initialize MemorySpdPtr pointers in
cannonlake soc code. In the first build, we did not use GPP_F2, so we
need to add an internal pulldown as those early devices were all dual
channel devices.
BUG=b:123062346, b:122959294
BRANCH=None
TEST=Boot into current boards and ensure that we have 2 channels as expected
Also, verify that GPP_F2 is set to 0.
Change-Id: I89d022793580be603a93d0b177d73ce968529b5c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Port commit f1395d82: "ec/lenovo/h8: Add USB Always On" to the Thinkpad
x1_carbon_gen1 board as well, as it seems to work fine on all
generations.
See also commit 7ffb329f with Change-Id
I6dcbfaae2a444d9a679ecb64a87dc2a59b8fd281 ("mb/lenovo/*/cmos: Port USB
Always On").
Note that we don't need to call h8_usb_always_on() directly since commit
4f4322dd with Change-Id If812cd1ef8fb1a24d7fadbe834f574b40cbcd56a
("lenovo/h8,thinkpads: Re-do USB Always On").
Change-Id: Ib9070b659b0c9ad5dde4200ec2845c6fa2b78b25
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicola Corna <nicola@corna.info>
Like with any other Thinkpad, call MUTE(1) and USBP(0) on _PTS on the
Lenovo Thinkpad X1 Carbon 1st generation.
Without MUTE(1) the speakers sometimes glitch before going into S3 (if not
muted), while without USBP(0) the USB ports are always powered in S3,
regardless of the USB Always-On mode selected.
Change-Id: I86f3c5a72e2589c5570303bf68f39df3ef874cb8
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This change reads DRAM part number from EEPROM if available and
returns it using the SoC callback (mainboard_get_dram_part_number).
BUG=b:127609572
TEST=Verify that DRAM part number from EEPROM is added to DMI table
17 (dmidecode -t 17).
Change-Id: I6ade6999828b6d67aa78d04199138f195a97ba8c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In order to support mainboards that do not store DRAM part number in
the traditional way i.e. within the CBFS SPD for soldered memory, this
change provides a runtime callback to allow mainboards to provide DRAM
part number from a custom location e.g. external EEPROM on hatch.
For other boards it should be a NOP since the weak implementation of
mainboard_get_dram_part_num does nothing.
BUG=b:127609572
Change-Id: I9b2d4c33fc378b9a24b111971ec2bfdb5f8d57d0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31850
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adding Hatch_whl as a variant of hatch. This is a snapshot of the WHL
version of hatch so that we can rebuild the bios images for Hatch with
WHL SoC.
BUG=b:127310803
BRANCH=NONE
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
make sure HATCH_WHL is built as well.
Change-Id: I24510fa226878582a61f1846f0b56a2c65204a92
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Following changes are done to enable audio support on hatch
1. Enable I2C4 device at 400Khz at 1.8V
2. Configure GPIO for HP INT and SPKR_PA_EN
3. Add ACPI entry for RT5682 and MAX98357A
4. Enable I2S0 and I2S1 lines
5. Enable generic max98357a driver in Kconfig
BUG=b:123738217
BRANCH=none
TEST=Check SSDT table for RT5682 & MAX98357a entry.
Verify audio using Sound Open firmware (SOF)
Change-Id: I93f3917c19cc3f0f8fd7b5e1b4d9b24a59f45f84
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The r8152 kernel driver is expecting the AMAC() method to return
a raw buffer, not a string. To fix this simply remove the
ToString() in the return statement that was converting the buffer
to a string.
BUG=b:123925776
Change-Id: I7cd4244a1ccc7397d5969b817a52ea48867b4d17
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31807
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some Apollo Lake mainboards use SeaBIOS as payload. SeaBIOS requires the
initialization of the programmable interrupt controller (PIC) for
faultless operation. The PIC mode is need for USB support (e.g.
keyboard, memory stick) and for some Option ROMs (e.g. PXE ROM).
Therefore add setup_lapic() to configure the APIC.
Change-Id: I00b339ce1850729023db74da7f8845927a95dcc6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31802
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates the Kconfig linter to support the new CONFIG() macro
in the same manner that IS_ENABLED() was previously supported. It will
be flagged when it is used on non-bool Kconfigs or used with #ifdef, and
it is supported for checking used Kconfigs. Remaining uses of
IS_ENABLED() are flagged with a deprecation warning.
Change-Id: I171ea8bc8e2d22abab7fc4d87ff4cf8aad21084f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31776
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In preparation for the transition of hatch from WHL to CML, we are
creating a checkpoint called hatch_whl that we can use for creating
firmware compatible with the WHL hatch variant.
BUG=b:127310803
BRANCH=NONE
TEST=NONE
Change-Id: Iecae584ee6feefcf29955a4720e9c24bdc8abe6d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds support for logging wake source information in gsmi
callbacks. With this change, all the elog logging infrastructure can
be used for S0ix as well as S3 on cannonlake.
BUG=b:124131938
BRANCH=none
TEST=Verified that the wake events are logged during the S0ix resume:
6 | 2019-03-04 17:03:13 | S0ix Enter
7 | 2019-03-04 17:03:17 | S0ix Exit
8 | 2019-03-04 17:03:17 | Wake Source | RTC Alarm | 0
9 | 2019-03-04 17:03:55 | S0ix Enter
10 | 2019-03-04 17:03:56 | S0ix Exit
11 | 2019-03-04 17:03:56 | Wake Source | GPE # | 21
12 | 2019-03-04 17:04:36 | S0ix Enter
13 | 2019-03-04 17:04:45 | S0ix Exit
14 | 2019-03-04 17:04:45 | Wake Source | GPE # | 112
15 | 2019-03-04 17:05:01 | S0ix Enter
16 | 2019-03-04 17:05:09 | S0ix Exit
17 | 2019-03-04 17:05:09 | Wake Source | Power Button | 0
Change-Id: Id627843e22c2524dfa94395b780cf2134f386137
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change moves soc_fill_power_state and soc_prev_sleep_state to
pmutil.c. It allows the functions to be used across romstage and smm.
BUG=b:124131938
BRANCH=none
TEST=none
Change-Id: If24c3feeb77f4fb692ef0bf38d537b2b54de3c36
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Create the way of adding the discrete VGA OpROM at config UI (alternative to
./cbfstool ./cb.rom add -f vgabios_dgpu.bin -n pci1002,6663.rom -t optionrom )
DGPU options are accessible only if CONFIG_VGA_BIOS is enabled.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I0a7bf0fe95c833cf3df0c7cb20fc27b6ab218c5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Some of the older chipsets that are known not to have ME at all
were removed for some reason, add them back in.
Also some newer chipsets/ME models were missing, add them in.
Change-Id: Iaed9a342e478a483113bf81d25042a6041fbc4ba
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
This patch adds timestamp for "end of romstage" with postcar if platform
has selected postcar as dedicated stage.
If postcar stage doesn't exist then "end of romstage" timestamp will get
call while starting of ramstage as exist today.
TEST=It's been observed that "end of romstage" timestamp doesn't appear
in "cbmem -t" log when ramstage is not getting executed. As part of this fix
"end of romstage" timestamp is showing in "cbmem -t" log on Intel platform
where POSTCAR is a dedicated stage.
Change-Id: I17fd89296354b66a5538f85737c79145232593d3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds dedicated timestamp value for postcar stage.
TEST=Able to see "start of postcar" and "end of postcar" timestamp
while executing cbmem -t after booting to chrome console.
> cbmem -t
951:returning from FspMemoryInit 20,485,324 (20,103,067)
4:end of romstage 20,559,235 (73,910)
100:start of postcar 20,560,266 (1,031)
101:end of postcar 20,570,038 (9,772)
Change-Id: I084f66949667ad598f811d4233b4e639bc4c113e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CPU PM TIMER EMULATION logic will help UEFI payload to execute rather
wait for time tick in absence of TCO and ACPI PM timer after FSP-S.
BUG=N/A
TEST=Able to build and boot with tianocore payload.
Change-Id: I7fd11e728b7a14f41f08bc39bcd92a42a8aa6cff
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Rename VB2_DISABLE_DEVELOPER_MODE to VB2_CONTEXT_DISABLE_DEVELOPER_MODE.
See CL in CQ-DEPEND for details.
BUG=b:124141368
TEST=Build locally
CQ-DEPEND=CL:1460645
BRANCH=none
Change-Id: Ib9754425dc2f346e8edac584c4d076d13ae31d2d
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Rename VB2_SD_DEV_MODE_ENABLED to VB2_SD_FLAG_DEV_MODE_ENABLED.
See CL in CQ-DEPEND for details.
BUG=b:124141368
TEST=Build locally
CQ-DEPEND=CL:1460644
BRANCH=none
Change-Id: I298cd3a5026055e439de1ce409e61f1feb24369b
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The IS_ENABLED() macro is pretty long and unwieldy for something so
widely used, and often forces line breaks just for checking two Kconfigs
in a row. Let's replace it with something that takes up less space to
make our code more readable. From now on,
if (IS_ENABLED(CONFIG_XXX))
#if IS_ENABLED(CONFIG_XXX)
shall become
if (CONFIG(XXX))
#if CONFIG(XXX)
Change-Id: I2468427b569b974303084574125a9e1d9f6db596
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Separate the type field for the PSP directory table to better match the
AMD Platform Security Processor BIOS Architecture Guide (order #55758,
NDA only). Instead of a 32-bit type, change to an 8-bit value and an
8-bit subprogram field to allow for a more generic application across
family/model products.
This patch also eliminates the "fanless" types, previously added for
stoneyridge, and converts the --smufnfirmware and --smufnfirmware2
arguments to use a subprogram value of 1.
Subsequent patches will change the stoneyridge makefile to use the
new option, and eliminate the fanless arguments.
TEST=Boot google/grunt, confirm no difference in amdfw.rom file.
BUG=b:126691068
Change-Id: If8f33000c31cba21f286f54459de185c21e46268
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31735
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Replace variables and function arguments with a context that may be
maintained and passed. Add macros to clarify the pointer math. Add
functions to generate tables instead of relying on correct ordering
and math. Use defined sizes for tables instead of arbitrary additions
to an index.
TEST=Verify no difference in amdfw.rom for google/grunt before and
after, and verify a grunt build with PSP_COMBO=1 runs.
Change-Id: I7ad12fa5d615d1aa3648db40e3ea75f8cf2ed59a
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Consolidate the code that opens, stats, copies, and closes the
individual files into a single function.
TEST=Verify no difference in amdfw.rom for google/grunt before
and after the patch is applied
Change-Id: I2da0dd79186ccc8c762b58cf3decb9980378a5f7
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
There are effectively two unique sets of arguments for the utility,
causing one of two tables to be constructed. Both tables are
identical, however, and therefore the only practical difference is
the offset in the Embedded Firmware Structure which holds the pointer
to the table.
This patch is part 2 of 2 to reduce the number of command-line options
to amdfwtool. Part 1 added the --combo-capable option that helps
put the PSP directory pointer in the correct location. Part 2
removes the duplicated table, the support code, options, and updates
the usage text.
TEST=Build before/after images for grunt, bettong, apu2, and diff
hexdumps of the amdfw.rom files. Built/ran grunt with PSP_COMBO
defined as 1.
BUG=b:126691068
Change-Id: I542a7f5023137f30fbe00533452d4448117df487
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
To prepare for consolidating amdfwtool command-line options, change
the stoneyridge makefile to use the ones that will be kept. By using
the new --combo-capable option, the PSP directory's pointer still
appears in the correct location within the the Embedded Firmware
structure.
TEST=Confirm amdfw.rom file is unchanged before/after when building
google/grunt
BUG=b:126691068
Change-Id: Ia31ebdcb8c392d75c56811b60f1ae673f7ba79cb
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31730
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are effectively two unique sets of arguments for the utility,
causing one of two tables to be constructed. Both tables are
identical, however, and therefore the only practical difference is
the offset in the Embedded Firmware Structure which holds the pointer
to the table.
This patch is part 1 of 2 to reduce the number of command-line options
to amdfwtool. Create a new option that is used as an indicator for
which Embedded Firmware offset to use. Part 2 will be added once
makefiles no longer use the duplicated options.
This patch also adds two new options for fanless SMU firmware to be
used instead of the ones that will be removed in part 2.
TEST=Verify no difference in amdfw.rom for google/grunt before
and after the patch is applied
BUG=b:126691068
Change-Id: I249700c6addad1c0ecb495a406ffe7a022dd920b
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The fletcher32 algorithm generates a sum over a range of 16-bit
WORDs. Change the function's interface to be more generic,
accepting a more intuitive size in BYTEs. Don't require the
caller to understand the nature of the algorithm and convert to
WORDs prior to calling.
TEST=Verify no difference in amdfw.rom for google/grunt before
and after the patch is applied
Change-Id: Iad70558347cbdb3c51bd598479ee4484219c0869
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31728
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Replace the use of multiples of DWORDs with structures that
describe the Embedded Firmware Table, and PSP directory
headers & entries.
TEST=Verify no difference in amdfw.rom for google/grunt build
(Family 15h Models 70h-7Fh), amd/bettong (F15h 60h-6Fh),
and pcengines/apu2 (F16h 30h-3Fh). PSP_COMBO builds but
was not verified.
Change-Id: If05952d9282a0fa5a397984eaae671fb33f6134a
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Correct an oversight in the utility that attempts to match up eligible
PSP directory table entries with blob names passed on the command
line. A 1:1 matchup of items shouldn't be assumed, so the i iterator
shouldn't be used to walk both lists.
This change has no effect on google/grunt (Family 15h Models 70h-7Fh),
but eliminates blank entries of all FF's on builds of amd/bettong
(F15h 60h-6Fh) and pcengines/apu2 (F16h 30h-3Fh). Removal of entries
also affects the checksum accordingly.
TEST=Build before/after images for grunt, bettong, apu2, and diff
hexdumps of the amdfw.rom files
Change-Id: I13e359d3cc6f5ce408bbf077feec3707ee2b3838
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31726
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Until now the TCPA log wasn't working correctly.
* Refactor TCPA log code.
* Add TCPA log dump fucntion.
* Make TCPA log available in bootblock.
* Fix TCPA log formatting.
* Add x86 and Cavium memory for early log.
Change-Id: Ic93133531b84318f48940d34bded48cbae739c44
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
We want to publish "arcada_ish.bin" as the fw name for Integrated
Sensor Hub (ISH) so the kernel shim loader code can use it to
construct the correct path in /lib/firmware/intel for the firmware
load process.
BUG=b:122722008
TEST=Verify that shim loader CLs use new value when constructing
firmware path
Change-Id: I6299de82566a3bad8521f8158bb047d5c1ff0cf8
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We want to be able to specify the firmware variant suffix
in the devicetree.cb configuration for particular firmware
builds. This driver allows us to specify the firmware_variant
property in the device tree and have it populate a _DST table
in the SSDT ACPI table for the ISH device, thus making the
suffix available to the kernel (See crrev.com/c/1433482 for kernel
change that uses the value)
BUG=b:122722008
TEST=decompile DDST table and verify that new firmware-variant value
is present. Also verfied that kernel can access this new field using
the shim loader kernel CLs
Change-Id: Id8be986185282521aee574027503eaf8968e1508
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The __pci_driver and __cpu_driver uses variable length arrays which are
constructed by the linker at build-time.
The linker always place the structs at 16-byte boundary, as per
"System V ABI". That's not a problem on x86, as the struct is exactly
16 Bytes in size. On other platforms, like x86_64 it breaks, because the
default data alignment isn't SysV compatible.
Set -malign-data=abi to make x86_64 gcc use the SysV psABI.
Fixes broken __pci_driver and __cpu_driver on x86_64.
Change-Id: I2491d47ed03dcfd8db110dfb181b2c5281449591
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30116
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are two known reverse-engineered ways to manage battery
thresholds.
This patch implements them and adds a way to enable them for
different mainboards.
Tested on W530 with 4.18.3-gentoo kernel and X220 with 4.20.11.
Works fine with new Linux userspace API for controlling battery
thresholds, available since 4.17.
(/sys/class/power_supply/BAT0/charge_(start|stop)_threshold).
The new API is supported by TLP (you might need to set NATACPI_ENABLE=1
in /etc/tlp.conf).
tpacpi-bat works fine too.
Signed-off-by: Alexey Kharlamov <der@2-47.ru>
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Change-Id: I2a90f9e9b32462b8a5e9bc8d3087ae0fea563ea5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/23178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This change adds support for the SuperIO chip IT8613E. This chip uses
FANs 2-5 and has SmartGuardian always enabled (no ON/OFF control) so
it relies on support in common ITE code. LDNs were taken from IT8613E
Preliminary Specification V0.3.
Change-Id: I73c083b7019163c1203a5aabbef7d9d8f5ccb16a
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This is a great check, but unfortunately it's currently not effective
because most uses of IS_ENABLED() do not have whitespace in front of
them (they're mostly used as part of an if (IS_ENABLED(...)) condition).
This patch makes the linter a little more generous in what it considers
in scope to avoid these false negatives in the future.
Change-Id: I2296410c73cd6e918465c90db33e782936bec0f9
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31746
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This IS_ENABLED(XXX) line should've clearly been IS_ENABLED(CONFIG_XXX).
This patch can fix that. However, I don't have (and don't plan to
acquire) an affected system to test, so approve at your own risk (or
let me know if I should just remove that check instead).
Change-Id: I79a0fca65853798ee45c3779b437864ba3cf2b1e
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This IS_ENABLED(XXX) line should've clearly been IS_ENABLED(CONFIG_XXX).
This patch fixes the issue. Not tested on a real board, but looking at
the affected code paths suggests that this will result in no effective
change anywhere (since CAR should already be torn down by the time this
is called on FSP1.0 boards, so do_car_migrate_variables() would have
immediately exited anyway).
Change-Id: I74e0ed4d04471ee521ff5c69a74a6f4c949e5847
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
For Chrome OS (or vboot), The PRESERVE flags should be applied on
following sections:
RO_PRESERVE, RO_VPD, RW_PRESERVE, RW_ELOG, RW_NVRAM, RW_SMMSTORE,
RW_VPD, RO_FSG (b:116326638), SI_GBE (chromium:936768),
SI_PDR (chromium:936768)
With the new PRESERVE flag, we don't need RO_PRESERVE and RW_PRESERVE in
the future. But it's still no harm to use it if there are multiple
sections all needing to be preserved.
BUG=chromium:936768
TEST=Builds google/eve and google/kukui inside Chrome OS source tree.
Also boots successfully on eve and kukui devices.
Change-Id: I6664ae3d955001ed14374e2788d400ba5fb9b7f8
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
When updating firmware, it is very often that we may want to preserve
few sections, for example vital product data (VPD) including serial
number, calibration data and cache. A firmware updater has to hard-code
the section names that need to be preserved and is hard to maintain.
A better approach is to specify that in FMAP area flags (the `area_flag`
field) using FMAP_AREA_PRESERVE. With this patchset, a FMD parser flag
"PRESERVE" is introduced and will be converted to FMAP_AREA_PRESERVE
when generating FMAP data (by fmap_from_fmd.c).
For example, The FMD statement:
RO_VPD(PRESERVE)@0x0 16k
will generate an FMAP firmware section that:
area_name = "RO_VPD"
area_offset = 0
area_size = 16384
area_flags = FMAP_AREA_PRESERVE
BUG=chromium:936768
TEST=make; boots on x86 "google/eve" and arm "google/kukui" devices
Manually added 'PRESERVE' to some FMD files, and verify (by running
fmap.py) the output coreboot.rom has FMAP_AREA_PRESERVE set
Change-Id: I51e7d31029b98868a1cab0d26bf04a14db01b1c0
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The recent toolchain update also updated binutils, which has a new
relocation type, introduced with commit bd7ab16b
(x86-64: Generate branch with PLT32 relocation).
Add support for R_X86_64_PLT32, which is handled as R_X86_64_PC32.
Add comment explaining the situation.
Fixes build error on x86_64.
Change-Id: I81350d2728c20ac72cc865e7ba92319858352632
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31468
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Qemu does not have a real CAR but postcar stage is still useful
for testing the stage.
The postcar stage is also mandatory for x86_64 to setup
pagetables for x86_64 ramstage.
Do not set up MTRRs, as qemu ignores them anyways.
Tested on qemu-i440fx and qemu-q35.
Change-Id: I6638534d99fde312e55b6a6be8c95e4cb25cca80
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The idea of "annotation" for firmware sections was pretty flexible, but
in future we will want multiple attributes applied to same area. For
example, indicate the section must be preserved when updating firmware
so serial number or MAC address can be preserved.
The solution here is to extend annotation so it can take multiple
identifiers (flags) in a row. For example, to declare a 64KB COREBOOT
section as CBFS using annotation:
COREBOOT(CBFS)@0x0 64k
If there's a new flag "PRESERVE" indicating the section must be
preserved before update, we can declare it following CBFS flag:
COREBOOT(CBFS PRESERVE)@0x0 64k
The flags are directly parsed in fmd_parser, and stored in an union
flashmap_flags. Output modules can choose to ignore or process the
flags.
Currently the only supported flag is "CBFS" (for backward compatible
with annotation). There will be more new flags in follow up patches.
BUG=chromium:936768
TEST=make; boots on x86 "google/eve" and arm "google/kukui" devices
Change-Id: Ie2d99f570e6faff6ed3a4344d6af7526a4515fae
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31706
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
git diff needed to emit diffs without prefix (e.g. a/ and b/) for
clang-format-diff to be able to work.
Also require that the test succeeds, but note that it only runs on
trees whitelisted in $(top)/.clang-format-scope.
Change-Id: I7e9a32eb9281b5cb0b45506a206500fd1d315372
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Intel Braswell SoC contains SMBus controller but no support
is available for this controller.
This controller is compatible with the Intel SMBus support in the
southbridge common directory.
To be able using smbus support from the Intel common directory
the smbus.c is moved outside SOUTHBRIDGE_INTEL_COMMON
dependency block.
Use SOUTHBRIDGE_INTEL_COMMON_SMBUS to include support.
BUG=N/A
TEST= Facebook FBG-1710 LCD panel
Change-Id: Ie3d4f657558a1aed21b083ef5cad08ea96e629c3
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Apollo Lake has four GPIO communities each with a single group named
after the physical location of the pads (I guess): North West, North,
West and South West.
Also add some logic to be able to tag the default function of a pad
(with an asterisk before its name). This seems easier to review in the
tables, but we could also encode the number of the default explicitly
instead.
Used Intel documents:
- 334817-001 (datasheet vol. 1)
- 334819-001 (datasheet vol. 3)
Change-Id: I5cd687fdc1d2ae81f2e948178bf319897b47f031
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Felix Singer <migy@darmstadt.ccc.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Enable the support for providing a MAC address for a dock to use based on
the VPD values set in the platform.
BUG=b:123925776
TEST=tested on sarien by setting VPD values and observing the string
returned by the AMAC() method:
> vpd -i RO_VPD -s "ethernet_mac0"="AA:AA:AA:AA:AA:AA"
> vpd -i RO_VPD -s "dock_mac"="BB:BB:BB:BB:BB:BB"
1) Test with no policy set, returns "dock_mac"
ACPI Debug: "VPD region RW did not verify"
ACPI Debug: "Found VPD KEY dock_mac = BB:BB:BB:BB:BB:BB"
ACPI Debug: "MAC address returned from VPD: BB:BB:BB:BB:BB:BB"
ACPI Debug: "AMAC = _AUXMAC_#BBBBBBBBBBBB#"
2) Test with policy set to "builtin", returns nothing
> vpd -i RW_VPD -s "dock_passthru"="builtin"
ACPI Debug: "Found VPD KEY dock_passthru = builtin" [AMAC returns Zero]
3) Test with policy set to "ethernet_mac0"
> vpd -i RW_VPD -s "dock_passthru"="ethernet_mac0"
ACPI Debug: "Found VPD KEY dock_passthru = ethernet_mac0"
ACPI Debug: "Found VPD KEY ethernet_mac0 = AA:AA:AA:AA:AA:AA"
ACPI Debug: "MAC address returned from VPD: AA:AA:AA:AA:AA:AA"
ACPI Debug: "AMAC = _AUXMAC_#AAAAAAAAAAAA#"
4) Test with policy set to "dock_mac"
> vpd -i RW_VPD -s "dock_passthru"="dock_mac"
ACPI Debug: "Found VPD KEY dock_passthru = dock_mac"
ACPI Debug: "Found VPD KEY dock_mac = BB:BB:BB:BB:BB:BB"
ACPI Debug: "MAC address returned from VPD: BB:BB:BB:BB:BB:BB"
ACPI Debug: "AMAC = _AUXMAC_#BBBBBBBBBBBB#"
Change-Id: I90474e264cc433c0fd1a4b0dbaf98e5f74180d54
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
This change adds support for providing a MAC address that can be used
by the OS network drivers to change the MAC address that a NIC uses.
The Realtek r8152 driver in the Linux kernel supports a MAC address
passthru feature which can result in the dock ethernet port using the
same MAC address that is assigned to the internal NIC. This is done
by calling an ACPI method at \_SB.AMAC() which returns a formatted
string containing the MAC address for the dock to use.
The Linux kernel implementation can be found at
drivers/net/usb/r8152.c:vendor_mac_passthru_addr_read()
This is implemented specifically for Chrome OS as it relies on VPD
to determine the MAC address to supply.
The policy which controls where the dock MAC address comes from is
written into RW_VPD property "dock_passthru":
"dock_mac" or empty: Use MAC address from RO_VPD value "dock_mac"
"ethernet_mac0": Use MAC address from RO_VPD value "ethernet_mac0"
"builtin": existing dock MAC address (return nothing)
The MAC address in VPD is the standard format AA:BB:CC:DD:EE:FF and
it must be converted into the string format expected by the OS which
involves some string manipulation which ACPI is not great at handling.
BUG=b:123925776
TEST=this was tested on a sarien board by setting the VPD keys to
their expected values and observing if the AMAC() method returns the
expected string.
Change-Id: I3335e5d924155431e299844e2aaace62168294e0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
This ACPI device presents an interface that allows other ACPI devices
or methods to read VPD strings. The VPDF() method is provided the
VPD partition to look in, and the name of the VPD key to find and it
will return the VPD string if it exists.
For example: VPD.VPDF ("RO", "serial_number")
BUG=b:123925776
TEST=this was tested on a sarien platform by adding ACPI code that
searches for a VPD key and returns the value it finds, and then setting
that VPD string from the OS with the Chrome OS 'vpd' utility to ensure
the ACPI method returns the correct value.
Change-Id: I4668f66d7f7f364ac8c3b064d406b24135abb0f6
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Store the memory address of VPD region start and length for the memory
mapped RO_VPD and RW_VPD into GNVS so they can be used by ACPI code.
BUG=b:123925776
TEST=boot on sarien and verify VPD start/length in GNVS
Change-Id: I39073a9d78f5ff60bfe088860c087a5167f05fdf
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Create the ISH ACPI device so we can hang fields off of a _DSD table.
Since this is also a PCI device that has run time probing, we can always
emit the ACPI device and let the device tree turn the device on or off.
BRANCH=none
BUG=b:122722008
TEST=verify that _DSD table gets publish under ISH device in kernel ACPI
tables. Also verified that device is still turned off if device tree for
ISH is off.
Change-Id: Ic0231f1ac637fea0e251eb3ac84f0fd8d64c12b2
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31681
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The following remarks show up during cannonlake based platform coreboot
build:
dsdt.asl 55: Offset (0x00),
Remark 2158 - ^ Unnecessary/redundant use of Offset operator
dsdt.asl 136: Offset (0xa8),
Remark 2158 - ^ Unnecessary/redundant use of Offset operator
Address those two remarks in coreboot.
BUG=N/A
TEST=Build coreboot and check build log to see no more remark.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Iad660347b32d90ac1176654820375e30a21b5ffe
Reviewed-on: https://review.coreboot.org/c/31666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Using ACPICA version 20180927 or greater, IASL detects Unnecessary/redundant
uses of the Offset() operator within a Field Unit list.
It then sends a remark "^ Unnecessary/redundant use of Offset".
Offsets refer to the current offset are unnecessary.
example:
OperationRegion (OPR1, SystemMemory, 0x100, 0x100)
Field (OPR1)
{
Offset (0), // Never needed
FLD1, 32,
Offset (4), // Redundant, offset is already 4 (bytes)
FLD2, 8,
Offset (64), // OK use of Offset.
FLD3, 16,
}
We will have those remarks:
dsdt.asl 14: Offset (0),
Remark 2158 - ^ Unnecessary/redundant use of Offset
operator
dsdt.asl 16: Offset (4),
Remark 2158 - ^ Unnecessary/redundant use of Offset
operator
Change-Id: If53072c6a91dd794c70d1fab8697b1713d400fe8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
IASL version 20180927 and greater, detects Unnecessary/redundant uses of
the Offset() operator within a Field Unit list.
It then sends a remark "^ Unnecessary/redundant use of Offset"
example:
OperationRegion (OPR1, SystemMemory, 0x100, 0x100)
Field (OPR1)
{
Offset (0), // Never needed
FLD1, 32,
Offset (4), // Redundant, offset is already 4 (bytes)
FLD2, 8,
Offset (64), // OK use of Offset.
FLD3, 16,
}
We will have those remarks:
dsdt.asl 14: Offset (0),
Remark 2158 - ^ Unnecessary/redundant use of Offset
operator
dsdt.asl 16: Offset (4),
Remark 2158 - ^ Unnecessary/redundant use of Offset
operator
Change-Id: Ie1f2a2ace335af7984209c9e286b9f85e5342a7e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31671
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
using '--single-branch' when cloning the tianocore repo
prevents the use of other branches/commits outside of the
checked-out coreboot_fb branch, so remove it.
Test: build with TIANOCORE_REVISION selected and revision
set to origin/master, verify checkout succeeds
Change-Id: If8c93aa87957ba2ff9ab7a58e84d2a25b48ec346
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
When updating firmware, we may need to preserve some sections like VPD,
calibration data, ... etc. The logic can be hard-coded in updater as a
list of known names, but a better solution is to have that directly
declared inside FMAP area flags.
To do that, the first step is to apply the changes in flash map
(http://crosreview.com/1493767). A new FMAP_AREA_PRESERVE is now
defined and will be set in future with new syntax in FMD parser.
BUG=chromium:936768
TEST=make; boots an x86 image.
Change-Id: Idba5c8d4a4c5d272f22be85d2054c6c0ce020b1b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Local APIC was not configured.
Add setup_lapic() to configure the APIC.
BUG=N/A
TEST= Ubuntu 4.15.0 reports correct local APIC information
on Intel CherryHill CRB
Change-Id: Ic1da5b1bf235f34b957142e86c70a9dbfa3ded1d
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
HDA support did not configure the codecs correclty.
Use Intel common block support to configure the codecs.
To use common Intel HDA support file hda.c file has been
removed and Braswell HDA device ID is added to list of
supported PCI devices in intel/common/block/hda/hda.c.
CONFIG_SOC_INTEL_COMMON_BLOCK and
CONFIG_SOC_INTEL_COMMON_BLOCK_HDA are enabled
to include hda.c in build.
When codec table is available at board level
SOC_INTEL_COMMON_BLOCK_HDA_VERB must be enabled
and a codec table must be supplied.
BUG=N/A
TEST=Facebook FBG-1701 ALC298 configuration
Change-Id: I5c23ec311e5b5a6dfd6f031aa19617407fe8ed63
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Since ACPI v2.c, this field is access_size.
Currently, coreboot is using ACPI v3,so we can drop '.resv' field.
Change-Id: I7b3b930861669bb05cdc8e81f6502476a0568fe0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch makes the way to protect flash regions selectable. If you
don't want to use ifdtool for modification of flash descriptor, enable
the new option. Otherwise, the previous config settings for all
mainboards will be retained.
Change-Id: I46ec6339008edcc78fe76682eed5714f85354937
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/31639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
We load it once for the BSP in advance and let the MP init handle it for
the APs. The BSP load could also be done earlier, e.g. before CAR setup,
to align with other platforms.
TEST=Booted ThinkPad X200s and checked log: Microcode is loaded
correctly on the BSP before SMM setup, and reported to be up
to date on all cores after.
Change-Id: I85adb22a608ca3e7355bd486ebba52ec8fdd396c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/31664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Some ITEs have more than 3 independent FAN controller outputs. As the
initial implementation assumed only 3 outputs some registers are not
consequently numbered. This change adds macros for accessing those
registers.
Additionally some chips have SmartGuardian always enabled, without the
option for turning it off. For these chips bits that were responsible
for ON/OFF control are either reserved or have different meaning.
Another Kconfig option is added to disable ON/OFF functionality on
platforms that do not support it.
Change-Id: Icd60a16b6b5583a3b981bdc220aac472c2a8f40f
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/31616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
In order to prevent keyboard keys pressed at boot from causing issues
in the payload remove the PS2 keyboard driver so it does not get
initialized until it is needed in libpayload.
This was enabled initially because the keyboard controller on this
platform does not come up in translated mode, so unless coreboot
called keyboard_init() the keyboard would never work properly in the
kernel because it would come up as an "AT Raw" device instead of an
"AT Translated" device.
Instead of initializing the keyboard in coreboot a workaround is
added to the payload to put the keyboard into translated mode.
BUG=b:126633269
TEST=boot on sarien while pressing keys and ensure libpayload and/or
the kernel does not have any issues initializing the keyboard.
Change-Id: I765e808f0d2589cf23c0349798a07e2706a2a7a4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
If a PS/2 AUX device is not present then the AUX test command
during i8042_probe() will time out and add ~500ms to the boot time.
In order to avoid this only test the PS/2 AUX port if
CONFIG_LP_PC_MOUSE is enabled.
BUG=b:126633269
TEST=boot on device without AUX port and check that this command
does not get executed, saving ~500ms at boot.
Change-Id: I2ebdecc66933bd33d320b17aa4608caf4aaf54aa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
If keys are pressed at boot some keyboard controllers will not
properly respond with an ACK to commands, which results in the
keyboard_init function aborting before it adds the keyboard to the
input device list.
This same keyboard controller will manage to properly return keyboard
data when keys are pressed later, so it is possible for it to be
functional in the payload even if it does not respond properly to
every command during initialization.
In order to allow payloads to use the keyboard when this happens a
new Kconfig option is added to ignore the keyboard ACK response and
always add the keyboard to the input device list. This option is
disabled by default and must be enabled by the specific boards that
need it.
BUG=b:126633269
TEST=boot on device with this controller and press keys during boot
and see that the keyboard is still functional in the payload.
Change-Id: Icc6053f99804f1b57d785cb04235b5c4b8d5426f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We had two ways to configure the serial IRQ mode. One time in the
devicetree for FSP and one time through Kconfig for coreboot. We'll
use `enum serirq_mode` from soc/intel/common/ as a devicetree option
instead. As the default is `quiet mode` here and that is the most
common mode, this saves us a lot of lines.
In four cases kblrvp8, 11 and librem 13v2, 15v3, we had conflicting
settings in devicetree and Kconfig. We'll maintain the `continuous`
selection, although it might be that coreboot overrode this earlier
on the kblrvps.
Note: A lot of Google boards have serial IRQ enabled, while the pin
seems to be unconnected?
Change-Id: I79f0cd302e335d8dcf8bf6bc32f3d40ca6713e5c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/31596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add Kconfig options to use custom bootsplash file,
dependent on using MrChromebox's stable branch, with
help info conveying required file format.
Adjust Makefile to copy the custom bootsplash and
overwrite the default Logo.bmp file, handling both
absolute and relative paths, and restore the original
logo file after building so as to keep the working
directory clean.
Test: build with and without custom bootsplash, ensure
correct bootsplash displayed
Change-Id: I164f46777169801cff56633fd920bc81b7c8129a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
INT_MODEL defined in ACPI 1.0 and renamed to reserved since V 2.0.
The value for this field is zero but 1 is allowed to maintain
compatibility with ACPI 1.0.
So set this value to zero as we are using greater version than ACPI 1.0.
Change-Id: I910ead4e5618c958a7989f4c309a3a4bb938e31a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29986
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: David Guckian
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On Sarien, change pin config of 0x19 (headset mic) and
0x21(headset headphone) to change jack location so that naming does
not use "Front" in the name."Front Headphone" --> "Headphone" so it
matches naming on Arcada.
BUG=b:126334749
TEST= verify with 'evtest' command that jack name is
"HDA Intel PCH Headphone" not "HDA Intel PCH Front Headphone"
Change-Id: I36ccf0c0a3952ab363fe6ee313fac8f0cce4dd61
Signed-off-by: Joyce Toh <joyce.toh@intel.com>
Reviewed-on: https://review.coreboot.org/c/31624
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The fdt in the maskrom cannot be used to start linux. The correct fdt
is dumped by replacing the bbl of the original firmware and used in
coreboot.
Correct the mac address in fdt by reading otp
Change-Id: Ic29f0e590311360b85fafd12ebc36cd189fbbc38
Signed-off-by: Xiang Wang <wxjstz@126.com>
Reviewed-on: https://review.coreboot.org/c/31047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Calculation of memory reserved by FSP is incorrect.
Use CBMEM_ID_FSP_RESERVED_MEMORY to determine the memory area
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: If68bda39ba2b1f3be4ed4bc872710be7bbd4948b
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Preliminary dptf change for Atlas
- Throttle charger using all temp sensors (not just ambient)
- Throttle charger with higher priority than CPU
- Update throttle temperature using data from surface thermistor
in thermal chamber test
BUG=b:113101335
BRANCH=None
TEST=based on preliminary data from thermal chamber test
Change-Id: Ic1ab72f569e8a4f7bffc5560518fb703d32f4b21
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Caveh Jalali <caveh@google.com>
The level/edge mode of PIRQ is not configured and i8259 PIC not initialized.
Add calls to:
- i8259_configure_irq_trigger()
- setup_i8259()
- write_pci_config_irqs()
to correct the configuration of interrupts.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: I128cb35dd0e348a9cd9fb162651e0aa2b7e4a3ef
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Static scan does not know the contents of the fixed MTRR descriptor, so
it has no way to eval the result for variable num_ranges. If num_ranges
is less or equal to 0, the for loop will not be entered, and the values
of fixed_msrs will not be set. Asserting that num_ranges is greater than
0 ensures the loop enters at least once.
BUG=b:112253891
TEST=build grunt
Change-Id: Ieec0ac432c745bde4b1700539c266625da6cfd77
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/31527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
After loading compressed files in CBFS, we should check the decompressed
size is equal to the expected size. This might help us detect file
content corruption or compressor/decompressor bugs.
BUG=none
BRANCH=none
TEST=manually (we can still boot into kernel on Kukui, and verify that
loading files from CBFS still works by seeing ChromiumOS firmware
screen).
Change-Id: Ia756cc5477670dd0d1d8aa59d4160ab4233c6795
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/31564
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, cbfs_decompress() calls ulzma() and ulz4f() for LZMA/LZ4
decompression. These two functions don't accept input/output size as
parameters. We can make cbfs_decompress more robust by calling ulzman()
and ulz4fn() instead. This could prevent us from overflowing destination
buffer.
BUG=none
BRANCH=none
TEST=boot into kernel on Kukui with COMPRESSED_PAYLOAD_LZMA /
COMPRESSED_PAYLOAD_LZ4.
Change-Id: Ibe617825bd000ed618791d8e3c5f65bbbd5f7e33
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/31606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
The name was wrong. mFCPGA478 is actually a pseudonym for mPGA478MN,
the successor of the socket that was meant.
The official name of this socket is mPGA478MT. But "Socket M" is much
easier to distinguish.
Change-Id: I4efeaca69acddfcdc5e957b0b521544314d46eeb
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/31642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
coreboot did not program all GPIOs from C0 to C7 correctly which are
SMBUS GPIO. Some of the GPIOs are left in default mode which is
native function but we need to configure as GPIO mode and provide proper
configuration as per schematic.
After fixing GPIO, CSME power gating issue also gets fixed since SMBUS was not
getting idle due to GPIO configuration and CSME was not getting power
gated due to SMBUS.
BUG=b:123702553
BRANCH=none
TEST=Check on hatch board. CSME was not getting power gated for s0ix.
After applying this patch CSME is power gated now
Change-Id: I5c6b9310dcc7bade0023abd5524781ce71df28be
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Change ac8c60e (soc/intel/cannonlake: Disable ACPI mode as part of
pmc_soc_init) moved disabling of ACPI mode to pmc_soc_init to keep it
more aligned with the behavior on other Intel SoCs. However, as the
PMC device is hidden, it never gets enumerated and so init function
does not get called for it. This change moves the call to disable ACPI
mode to exit of BS_DEV_INIT instead.
BUG=b:126016602
TEST=Verified that:
1. pmc_set_acpi_mode is actually getting called.
2. EC panic event gets logged to eventlog correctly.
Change-Id: Ie7025e322fa0abc21367a520184a4c7741eba1e6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31633
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch implements RTC initialization.
1. initialization dcxo
2. rtc clock using dcxo 32k
3. export RTC_32K1V8_0 to SOC, export RTC_32K1V8_1 to WLAN
4. rtc register initialization
5. refactor the driver common part
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Icccb9360a507fcbfd865b107cd3630e71c810d55
Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Because coreboot's asserts aren't fatal by default, scan-build finds
problems in code that is actually protected by an assert. This
change fixes that and allows us to add asserts to protect
against other failures.
Change-Id: I9fa605d6309bb40a9cef33b434c9256bf731f457
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/31650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Instead of using 2, 0 is now used for non-CBI provisioned board or
corrupted CBI board to confrom to the sku encoding.
BUG=b:123676982
BRANCH=kukui
TEST=test with un-provisioned board to verify the sku_id.
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: I66f29f8a46cd774b40354def7d3623ec44cb96ce
Reviewed-on: https://review.coreboot.org/c/31623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Various instances of google_chromeec_command() can return non-zero number
(both positive and negative) to indicate error -- fixing cbi_get_uint32()
and cbi_get_string() so they follow the same convention.
BUG=b:123676982
BRANCH=kukui
TEST=build with kukui/flapjack configurations
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: I7f0a8a61d01d942cba57036a17dd527fdbbf940c
Reviewed-on: https://review.coreboot.org/c/31585
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This function appeared previously unused (called only from rtc_display, also unused),
but it returned an incorrect weekday. Change the algorithm to use Zeller's Rule, a
well-known algorithm for calculuating weekdays.
Change-Id: Ibce6822942f8d9d9f39c2b6065cd785dca9e8e09
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Hatch implements active high SD_PWR_EN and requires a workaround
in _PS0 and _PS3 control methods to make sure SD_PWR_EN stays low
in D3. Select MB_HAS_ACTIVE_HIGH_SD_PWR_ENABLE to enable the same.
BUG=b:123350329
Change-Id: I96ab9660eb50100207fe9a237f5924b65eae0928
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
SD controller in CNL-PCH provides a ability to configure the behavior of
SD_VDD1_PWR_EN# as an active high or low signal. FSP provides an UPD
"SdCardPowerEnableActiveHigh" to control the same.
However, for platforms using SD_VDD1_PWR_EN# as active high, the SDXC
card connector is always powered and may impact system power. This is because
SD_VDD1_PWR_EN# does not de-assert during SDXC D3 or when SD card is not
inserted.
Workaround is to change the pad ownership of SD_VDD1_PWR_EN to GPIO and
force the TX buffer to low in _PS3. And restore the pad mode to native
function in _PS0.
Hence add a Kconfig option to update the UPD, which the board can select
based on how the SD_VDD1_PWR_EN is implemented on it. And, the workaround
gets applied based on this config.
BUG=b:123350329
Change-Id: Iee262d7ecdf8c31362aec3d95dd9b3e8359e0c25
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31445
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SD_CD# in Cannonlake PCH is also wired to an internal virtual GPIO,
expose that GPIO for kernel to configure card detect IRQ.
BUG=b:123350329
Change-Id: I566cc2eb11dc257366897a1efba905b8ddcf493d
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Adapted from Chromium commit 5351dc0d
[Edgar: To set the RX ODT limit and dram geometry with RAMID detection]
Several cyan variants require memory init parameters be passed to FSP
for handling of specific Micron modules; without these, RAM init will
fail when loading training data from the MRC cache, and boot will halt.
This was missed when I upstreamed edgar along with the other cyan
variants, so add the required memory init parameters for edgar as per
its source Chromium branch.
Test: build/boot on edgar board with affected Micron memory
modules, verify boot successful with populated MRC cache.
Change-Id: I6a2bc30b54ff1a17c854a90dfcb2308d27ee2be7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31615
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PMC initialization on Cannon Lake happens earlier in the boot sequence
than other SoCs because FSP-Silicon init hides PMC from PCI bus. As
ACPI disabling was done as part of PMC init, it was being called
earlier than what other SoCs do. This resulted in a different order of
events for some drivers e.g. ChromeOS EC. In case of ChromeOS EC, it
ended up clearing EC events (which happens as part of ACPI disabling
in SMM) before logging any events of interest that happen during
mainboard initialization.
This change moves the call to disable ACPI to pmc_soc_init just like
other SoCs to keep the order of events more aligned.
BUG=b:126016602
TEST=Verified that EC panic event gets logged to eventlog correctly.
Change-Id: Ib73883424a8dfd315893ca712ca86c7c08cee551
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Each smbios entry should be followed with two null bytes. In other
structures it's done by adding `u8 eos[2]` extra bytes at the end, it
was omitted in type38 (IPMI) though. This change fixes this - tables
decodes nicely:
```
IPMI Device Information
Interface Type: KCS (Keyboard Control Style)
Specification Version: 2.0
I2C Slave Address: 0x10
NV Storage Device: Not Present
Base Address: 0x0000000000000CA2 (I/O)
Register Spacing: 32-bit Boundaries
```
Signed-off-by: Lukasz Siudut <lsiudut@fb.com>
Change-Id: I8efea9612448f48e23e7b2226aea2a9f3bc21824
Reviewed-on: https://review.coreboot.org/c/31482
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This documents the API exposed by the x86 system management based
storage driver.
## SMMSTORE
SMMSTORE is a SMM mediated driver to read from, write to and erase a
predefined region in flash. It can be enabled by setting
`CONFIG_SMMSTORE=y` in menuconfig.
This can be used by the OS or the payload to implement persistent
storage to hold for instance configuration data, without needing
to implement a (platform specific) storage driver in the payload
itself.
The API provides append-only semantics for key/value pairs.
## API
### Storage region
By default SMMSTORE will operate on a separate FMAP region called
`SMMSTORE`. The default generated FMAP will include such a region.
On systems with a locked FMAP, e.g. in an existing vboot setup
with a locked RO region, the option exists to add a cbfsfile
called `smm_store` in the `RW_LEGACY` (if CHROMEOS) or in the
`COREBOOT` FMAP regions. It is recommended for new builds using
a handcrafted FMD that intend to make use of SMMSTORE to include a
sufficiently large `SMMSTORE` FMAP region. It is recommended to
align the `SMMSTORE` region to 64KiB for the largest flash erase
op compatibility.
When a default generated FMAP is used the size of the FMAP region
is equal to `CONFIG_SMMSTORE_SIZE`. UEFI payloads expect at least
64KiB. Given that the current implementation lacks a way to rewrite
key-value pairs at least a multiple of this is recommended.
### generating the SMI
SMMSTORE is called via an SMI, which is generated via a write to the
IO port defined in the smi_cmd entry of the FADT ACPI table. `%al`
contains `APM_CNT_SMMSTORE=0xed` and is written to the smi_cmd IO
port. `%ah` contains the SMMSTORE command. `%ebx` contains the
parameter buffer to the SMMSTORE command.
### Return values
If a command succeeds, SMMSTORE will return with
`SMMSTORE_RET_SUCCESS=0` on `%eax`. On failure SMMSTORE will return
`SMMSTORE_RET_FAILURE=1`. For unsupported SMMSTORE commands
`SMMSTORE_REG_UNSUPPORTED=2` is returned.
**NOTE1**: The caller **must** check the return value and should make
no assumption on the returned data if `%eax` does not contain
`SMMSTORE_RET_SUCCESS`.
**NOTE2**: If the SMI returns without changing `%ax` assume that the
SMMSTORE feature is not installed.
### Calling arguments
SMMSTORE supports 3 subcommands that are passed via `%ah`, the additional
calling arguments are passed via `%ebx`.
**NOTE**: The size of the struct entries are in the native word size of
smihandler. This means 32 bits in almost all cases.
#### - SMMSTORE_CMD_CLEAR = 1
This clears the `SMMSTORE` storage region. The argument in `%ebx` is
unused.
#### - SMMSTORE_CMD_READ = 2
The additional parameter buffer `%ebx` contains a pointer to
the following struct:
```C
structsmmstore_params_read{
void*buf;
ssize_tbufsize;
};
```
INPUT:
-`buf`: is a pointer to where the data needs to be read
-`bufsize`: is the size of the buffer
OUTPUT:
-`buf`
-`bufsize`: returns the amount of data that has actually been read.
#### - SMMSTORE_CMD_APPEND = 3
SMMSTORE takes a key-value approach to appending data. key-value pairs
are never updated, they are always appended. It is up to the caller to
walk through the key-value pairs after reading SMMSTORE to find the
latest one.
The additional parameter buffer `%ebx` contains a pointer to
the following struct:
```C
structsmmstore_params_append{
void*key;
size_tkeysize;
void*val;
size_tvalsize;
};
```
INPUT:
-`key`: pointer to the key data
-`keysize`: size of the key data
-`val`: pointer to the value data
-`valsize`: size of the value data
## External links
* [A Tour Beyond BIOS Implementing UEFI Authenticated Variables in SMM with EDKI](https://software.intel.com/sites/default/files/managed/cf/ea/a_tour_beyond_bios_implementing_uefi_authenticated_variables_in_smm_with_edkii.pdf)
Note, this differs significantly from coreboot's implementation.
Steps to access the flash IC are described here [T4xx series].
[T4xx series]: t4xx_series.md
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
