Current flash layout doesn't support the fsp debug builds since
the FW_MAIN_A/B doesn't have enough space to hold the fsp debug
binaries along with ME RW binaries.
This patch reduces the SI_ALL size to 3.5MiB and increase the
SI_BIOS to 12.5MiB to include both ME RW and FSP debug binaries.
BRANCH=dedede
TEST=Build and Boot jslrvp with fsp debug enabled coreboot.
Cq-Depend: chrome-internal:3425366
Change-Id: I6f6354b0c80791f626c09dabafe33eefccedb9c2
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48154
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
AGESA checks to make sure that the firmware version reading the MRC
cache is the same version that wrote it, so it doesn't need to be
erased during a firmware update.
BUG=b:173724014
TEST=Flash firmware to DUT, update firmware, check RW_MRC_CACHE was
not erased
BRANCH=Zork
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ice3d1d467c25366b7ef678cd6481d043f62644ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
As per latest schematics GPP_A15 is not used for EC_SYNC_IRQ
hence remove the unused GPIO.
Wrong GPIO configuration is causing platform reboot issue on
ADLRVP with Chrome SKU.
Change-Id: I704cd722683258c80197d8872d3bdaafb7c923dc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
List of changes in SPD:
1. SPD Revision (of JEDEC spec)
2. SDRAM Maximum Cycle Time (tCKAVGmax) (MTB)
3. MSB -> CAS Latencies Supported, First Byte
4. CAS Latencies Supported, Second Byte
5. CAS Latencies Supported, Third Byte
6. LSB -> CAS Latencies Supported, Fourth Byte
7. Minimum CAS Latency Time (tAAmin)
8. Fine Offset for SDRAM Maximum Cycle Time (tCKAVGmax)
9. Fine Offset for SDRAM Minimum Cycle Time (tCKAVGmin)
10.Cyclical Redundancy Code (0- 125 byte)
TEST=Able to build and boot with updated SPD.
Change-Id: Iae7f2693e87bffb2dfa20bd07b22f4a4768c56cb
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
When the global variable of a "struct" CBFS file is zero (for example,
CB:47696), the binary will appear in the .bss* section in the ELF file
(instead of .data). This results in an empty binary file added to CBFS,
so that file size check will fail when reading it at runtime.
BUG=b:173751635
TEST=emerge-asurada coreboot
TEST=Check sdram-lpddr4x-KMDP6001DA-B425-4GB is non-empty in CBFS
BRANCH=none
Change-Id: Idfd17d10101a948de0eb0522a672afd5c2f83b04
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47903
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The template for overridetree.cb includes HeciEnabled, which has
been removed from the CNL config struct, so remove it from the
overridetree.
BUG=b:174360951
TEST=`new_variant_fulltest.sh puff` succeeds
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: I87f67c53cc75d9ddd40b4960739180a95de6ecd6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Hook up the mainboard_ops driver and configure the GPIOs using .init,
since mainboard_silicon_init_params() is meant for the configuration of
the FSP, not the GPIOs.
Change-Id: I6ab8d258c6f81c90d835cb8d07c6387d3de76d85
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47850
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's no need to have the bootblock in its own sub-directory, so move
it to each SoC's main directory to avoid clutter. This makes soc/amd
more consistent with the coreboot code base in src/northbridge,
src/southbridge and src/soc with the exception of src/soc/intel.
Change-Id: I78a9ce1cd0d790250a66c82bb1d8aa6c3b4f7162
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47982
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the drobit variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171947885
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I63b7312bba236bd5af028359804d042f6850d8ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47787
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a Kconfig symbol for including the PCIe MMCONF setup function in the
build and select it when SOC_AMD_COMMON_BLOCK_PCI is selected and in the
southbridges call enable_pci_mmconf(), but don't select
SOC_AMD_COMMON_BLOCK_PCI.
Change-Id: I32de7450bff5b231442f9f2094a18ebe01874ee7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47878
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tiger Lake introduces new wake-capable devices, including thunderbolt
ports, TCSS XHCI & XDCI as well as DMA ports. Add new ELOG_WAKE_SOURCE
macros for each of these types of devices.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie5dae6514c2776b30418a390c4da53bda0b2d456
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add MT53D512M64D4NW-046 WT:F memory part to LP4x global list of
available LP4x parts and to the global JSON file containing LP4x parts
and their characteristics.
BUG=b:172993397
TEST=none
Change-Id: I09c6eab640c169dbdb451964967d14a31e314496
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Print whether the SOC supports TME/MKTME. If the SOC supports the
feature, print the status of enable and lock bit from TME_ACTIVATE
MSR. -t option prints this status.
Sample output:
If TME/MKTME is supported:
============= Dumping INTEL TME/MKTME status =============
TME supported : YES
TME locked : YES
TME enabled : YES
====================================================
If TME/MKTME is not supported:
============= Dumping INTEL TME status =============
TME supported : NO
====================================================
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I584ac4b045ba80998d454283e02d3f28ef45692d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If there are multiple statements that are conditional on the same
Kconfig option, group them and move the condition check around the
statement. If there's only one statement depending on one condition, use
the short form instead.
Change-Id: I89cb17954150c146ffc762d8cb2e3b3b374924de
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47876
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since there are sub-directories for both the cache-as-RAM case and the
non-CAR case where the RAM is already initialized when the x86 cores are
released from reset, move the CAR-specific parts of the Makefile.inc to
another Makefile.inc in the car sub-directory. Further patches will add
a Makefile.inc to the non-CAR directory.
Change-Id: I43a3039237d96e02baa33488e71c5f24effe8359
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47875
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit bd31642ad8 (intel/i210: Set bus master bit in command register)
is only necessary because a buggy OS expects Bus Master to be set, not
because the hardware requires Bus Master during initialization. It is
thus safe to defer the Bus Master request into the .final callback.
Change-Id: Iecfa6366eb4b1438fd12cd9ebb1a77ada97fa2f6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47401
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: siemens-bot
This change updates bootblock_pch_early_init() to perform P2SB
configuration before any other PCH controllers are initialized. This
is done because the other controllers might perform PCR settings which
requires the PCR base address to be configured. As the PCR base
address configuration happens during P2SB initialization, this change
moves the p2sb init calls before any other PCH controller
initialization.
BUG=b:171534504
Change-Id: I485556be003ff5338b4e2046768fe4f6d8a619a3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47885
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIO needs to be initialized before the IPMI device gets initialized,
so the GPIOs can be read/set by the code in CB:48096 and CB:48094. Thus,
use mainboard_ops.init for GPIO configuration instead of using the
indirection via a mainboard_enable function.
To make it more visible, that we use chip.init, rename `mainboard_init`
to `mainboard_chip_init`.
Tested successfully on X11SSM-F including the IPMI changes.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I192e69a34fa262b38bc40a95fb11c22a4041d0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Commit 056d552 introduced a bug where 0xFF gets set as OC pin value to
supposedly skip programming an OC pin for a disabled USB port. While the
value is correct for the other platforms, Skylake uses 0x08 for this
purpose. Correct this by using the enum value OC_SKIP (0x08) instead.
Change-Id: I41a8df3dce3712b4ab27c4e6e10160b2207406d1
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
- Drop vanished issue on PCIe warning
- Drop TODO section, since the TODOs are done
- Document the jumper J6, that was not documented by the vendor. Its
function has been determined by dissecting a dead board.
- The flash is not socketed anymore. Drop that note and compress the
whole paragraph. Also add a note about flashing via the BMC web
interface.
Change-Id: I2b5a08a6b6d80717621d6a30f31829fe4b84891a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Update UPDs required for the creation of DMAR table.
By default coreboot was not generating DMAR table for IOMMU which
was resulting in below error message in kernel:
DMAR: [Firmware Bug]: No DRHD structure found in DMAR table
DMAR: No DMAR devices found
These changes will publish DMAR table through ACPI and will not
result in the above error.
BUG=b:170261791
BRANCH=dedede
TEST=Build Dedede, boot to kernel and check dmesg if DMAR
table exists.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I97a9f2df185002a4e58eaa910f867acd0b97ec2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Currently, setting a custom FSP binary is only possible by using split
FSP-T/M/S FD files. This change introduces the possibility to pass a
combined FD file (the "standard" FSP format).
This is done by adding a new boolean Kconfig FSP_FULL_FD, specifying
that the FSP is a single FD file instead of split FSP-T/M/S FD files,
and making FSP_FD_PATH user-visible when the option is chosen. In this
case, the other options for split files get hidden.
When the user chooses to use a full FD file instead of the split ones,
the FD file gets split during build, just like it is done when selecting
the Github FSP repo (FSP_USE_REPO).
Test: Supermicro X11SSM-F builds and boots fine with custom FSP FD set.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I1cb98c1ff319823a2a8a95444c9b4f3d96162a02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Create the galtic variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.3.1).
BUG=b:170913840
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_GALTIC
Signed-off-by: FrankChu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Ie7534d56bc67aca4484f40af1221d669addc01fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47900
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id 9d4053d:
2020-11-20 01:51:08 +0000 - (Revert "Reland: Clean up implicit fall through.")
to commit id 48195e5:
2020-11-24 10:23:45 +0000 - (Makefile: Test for warning flags before using them)
This brings in 3 new commits.
Change-Id: I64f27f346df264cb6eeeb4e3203fcca7d35f7e83
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
RasModesEnabled
Use RasModesEnabled from SystemMemoryMapHob to define SMBIOS type
16 error correction type
Tested=Execute "dmidecode -t 16" to check if error correction type
is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I3636fcc4a874261cf484c10e2db15015ac5d7e68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Selecting SOC_INTEL_CSE_LITE_SKU without conditioning on CHROMEOS
force-selects CHROMEOS, per src/soc/intel/common/block/cse/Kconfig.
Conditioning on CHROMEOS allows for non-ChromeOS targets to be built.
Test: build wyvern variant with CONFIG_CHROMEOS=n
Change-Id: I61c9c78a3b02d64bab2813b7a80915b7ecf7f934
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Our current cbfstool has always added a compression attribute to the
CBFS file header for all files that used the cbfstool_convert_raw()
function (basically anything other than a stage or payload), even if the
compression type was NONE. This was likely some sort of oversight, since
coreboot CBFS reading code has always accepted the absence of a
compression attribute to mean "no compression". This patch fixes the
behavior to avoid adding the attribute in these cases.
Change-Id: Ic4a41152db9df66376fa26096d6f3a53baea51de
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Hook up the mainboard_ops driver and configure the GPIOs using .init,
since mainboard_silicon_init_params() is meant for the configuration of
the FSP, not the GPIOs.
Change-Id: I82f1eaf6693d9b117fb211776047058cdc787288
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
SMI handler was not installed for Xeon_sp platforms. This enables SMM
relocation and SMI handling.
TESTED:
- SMRR are correctly set
- The save state revision is correct (0x00030101)
- SMI's are properly generated and handled
- SMM MSR save state are not supported, so relocate SMM on all cores
in series
- Verified on OCP/Deltalake mainboard.
NOTE:
- Code for accessing a CPU save state is not working for SMMLOADERV2,
so some SMM features like GSMI, SMMSTORE, updating the ACPI GNVS
pointer are not supported.
- This hooks up to some soc/intel/common like TCO and ACPI GNVS. GNVS
is broken and needs to be fixed separately. It is unknown if TCO is
supported. This might require a cleanup in the future.
Change-Id: Iabee5c72f0245ab988d477ac8df3d8d655a2a506
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46231
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allows advertising support for a 1ch array DMIC in the NHLT table.
Boards use the NHLT if a microphone is connected to the DSP.
Tested on an Acer Aspire VN7-572G (Skylake-U) on Windows 10.
A custom ALSA topology will be required for Linux.
Change-Id: Idba3a714faab5ca1958de7dcfc0fc667c60ea7fd
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
According to the NHLT specification[1], PDM_DEV is defined as "1" on
Kabylake based platforms. coreboot currently sets it to "0" on
all platforms. Add an entry to the enum and use it to define
NHLT_PDM_DEV for Kabylake.
"Device Type" will resume from "2" on all platforms, but entries are
currently reserved.
Tested on an Acer Aspire VN7-572G (Skylake-U), which has a 1ch array
DMIC, on Windows 10.
1. https://01.org/sites/default/files/595976_intel_sst_nhlt.pdf
Change-Id: Ifbc67228c9e7af7db5154d597ca8d67860cfd2ed
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45010
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Split up gpio.h into two seperate compilation units, gpio.c and
gpio_early.c, containing the complete configuration and a minimal
configuration used in early stages.
Tested on clevo/l140cu and it still boots.
Change-Id: I5b056e8faac0c426a37501dbc175373c22dde339
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Get rid of cnl_configure_pads() since it is a hack for the FSP. Instead,
hook up to the mainboard_ops driver and configure the GPIOs using .init.
Tested on clevo/l140cu and it still boots.
Change-Id: I75dd15ab6d2b3b72b3ad0398df87b349fd00bc3c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Most of these comments have been copy-pasted or serve no purpose other
than to eventually turn into misleading info. While the description of
the first 120 bits of CMOS could be useful, it should instead be added
to the documentation for the CMOS option infrastructure, or /dev/null.
Moreover, trim down newlines to no more than two consecutive newlines.
Change-Id: I119b248821221e68c4e31edba71ba83b7d2e14e9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
List of changes:
1. Configure CTRLCLK and CTRLDATA for HDMI
2. Enable Ddc and HPD for Port-B
3. Disable dual eDP configuration for Port-A and B
TEST=Able to see depthcharge pre-boot screens over HDMI-B port.
Change-Id: I7509b981f35fc60a7885b2b07067cb0d35ec625f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
According to the latest Alderlake Platform FSP Integration Guide, the
minimum amount of stack needed for FSP-M is 512KiB. Change
DCACHE_RAM_SIZE and DCACHE_BSP_STACK_SIZE to reflect that (plus 1KB
previously determined empirically).
TEST=Able to pass FSP-M MRC training on LPDDR5 SKU without any hang.
Change-Id: Ic831ca9110a15fdb48ad31a7db396740811bf0f2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This turns on the compiler's printf style format string checker.
BUG=b:167517417
TEST=enabled all USB controllers on volteer and fixed resulting
compiler errors when USB_DEBUG is enabled.
Change-Id: Ic94ebcbafdde8a5f79278b5635111b99af40f892
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45025
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This fixes format string mismatch errors in the USB subsystem found by
the compiler's format string checker.
BUG=b:167517417
TEST=enabled all USB controllers on volteer and fixed resulting
compiler errors when USB_DEBUG is enabled.
Change-Id: I4dc70baefb3cd82fcc915cc2e7f68719cf6870cc
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
BAR address used during early initilization of GPSI 2 is overlapping with UART bar.
//For GSPI2 this is the address calculated
GSPI_BUS_BASE(0xFE030000,2)=0xFE032000
GSPI_BUS_BASE(bar, bus) ((bar) + (bus) * 4 * KiB)
//overlaps with
CONSOLE_UART_BASE_ADDRESS -> 0xfe032000
TEST=none
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I3249a91df8a2e319aff6303ef9400e74163afe93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
BAR address used during early initilization of GPSI 2 is overlapping with UART bar.
//For GSPI2 this is the address calculated
GSPI_BUS_BASE(0xFE030000,2)=0xFE032000
GSPI_BUS_BASE(bar, bus) ((bar) + (bus) * 4 * KiB)
//overlaps with
CONSOLE_UART_BASE_ADDRESS -> 0xfe032000
Change-Id: Id9f2140a6dd21c2cb8d75823cc83cced0c660179
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Enables the MMU primarily to allow the unaligned word reads that the
FMAP code requires. Without enabling this, the chip gets data access
exceptions.
Enabling the MMU also gives some advantages in allowing the icache and
dcache to be enabled, so is probably worth doing regardless.
Change-Id: Ic571570cc44b0696ea61cc76e3bce7167a3256cf
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Introduce a weak function to let the platform code provide the processor
voltage in 100mV units.
Implement the function on Intel platforms using the MSR_PERF_STATUS msr.
On other platforms the processor voltage still reads as unknown.
Tested on Intel CFL. The CPU voltage is correctly advertised.
Change-Id: I31a7efcbeede50d986a1c096a4a59a316e09f825
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
- Update url for docker install instructions.
- Update docker-cleanall target to require verification.
- Update docker-jenkins-attach target to check for docker and
use docker variable.
- Update spaces to tabs in the docs targets.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ic1e1a545024fe1fdc37d7d8c7e6f54f124d1697b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Changes (https://nasm.us/doc/nasmdocc.html):
Version 2.15.05:
Correct %ifid $ and %ifid $$ being treated as true.
Add --reproducible option to suppress NASM version numbers and
timestamps in output files.
Version 2.15.04:
Correct the encoding of the ENQCMDS and TILELOADT1 instructions.
Fix case where the COFF backend (the coff, win32 and win64 output
formats) would add padding bytes in the middle of a section if a
SECTION/SEGMENT directive was provided which repeated an
ALIGN= attribute. This neither matched legacy behavior, other
backends, or user expectations.
Fix SSE instructions not being recognized with an explicit memory
operation size (e.g. movsd qword [eax],xmm0).
Change-Id: I3f9aa8e743f2dc50fce1ce68718c0ae17209a509
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44694
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Subitem for VENDORCODE_ELTAN_VBOOT and VENDORCODE_ELTAN_MBOOT are
always displayed.
Add dependency and display these items when feature is enabled only.
Tested on Facebook FBG1701.
Change-Id: I51e47efddbcf51d87439bec33b85432da56fa4c6
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The CPX FSP-T does not respect the FSP2.x spec and uses registers where
coreboot has its initial timestamp stored.
If the initial timestamp is later than some other timestamps this
messes up the timestamps 'cbmem -t' reports as it thinks they are a
result from a timestamp overflow (reporting that it took 100k years to
boot).
TEST: The ocp/deltalake boots within the span of a lifetime.
Change-Id: I4ba15decec22cd473e63149ec399d82c5e3fd214
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch adds support for the Kontron mAL10 COMe module with the
Apollo Lake SoC together with Kontron T10-TNI carrierboard.
Working:
- UART console and I2C on Kontron kempld;
- USB2/3
- Ethernet controller
- eMMC
- SATA
- PCIe ports
- IGD/DP
- SMBus
- HWM
Not tested:
- IGD/LVDS
- SDIO
TODO:
- HDA (codec IDT 92HD73C1X5, currently disabled)
Tested payloads:
- SeaBIOS
- Tianocore, UEFIPayload - without video, EFI-shell in console only
Tested on COMe module with Intel Atom x5-E3940 processor (4 Core,
1.6/1.8GHz, 9.5W TDP). Xubuntu 18.04.2 was used as a bootable OS
(5.0.0-32-generic linux kernel)
Change-Id: Ib8432e10396f77eb05a71af1ccaaa4437a2e43ea
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
If AGESA is added as a raw binary (and not a stage), then cbfstool
does not perform relocation. In this case, it should be added only to
COREBOOT (i.e. default) CBFS since the binary needs to be present only
in one specific location that is present in the default CBFS.
Change-Id: I7a7edc217663f9d1d36b05308bbd35f56a28b9b1
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This register needs to be updated differently depending on the CPU
generation and stepping. Handle this as per reference code. Further,
introduce a bitfield for the register to make the code easier to read.
Change-Id: I51649cb2fd06c5896f90559f59f25d49a8e6695e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Values differ between Sandy and Ivy Bridge. Remove the lookup table,
since it contains duplicated values and is hard to see which values
correspond to which frequencies. New values come from reference code.
Change-Id: I3b28568f0053f1b39618e16bdffc24207547d81f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This is actually aggressive write training, similar to aggressive read
training. Rename it accordingly and refactor it to improve clarity.
Enabling IOSAV_n_SPECIAL_COMMAND_ADDR optimizations must only be done
for later Ivy Bridge steppings. Therefore, guard the code accordingly.
Change-Id: Ia3331b95c265113d94cb5d66c57a97cb77fc3dc9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
When memory is running at fast frequencies, power-down modes can lessen
system stability. Check tXP and tXPDLL values and use safer power down
modes if their values are high. Do not use APD with DLL-off on mobile:
vendor firmware does not use it, and it can influence system stability.
Change-Id: Ic8e98162ca86ae454a8c951be163d58960940e0e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This is actually an (incomplete) aggressive read training algorithm.
Rename functions and variables accordingly, and tidy up declarations.
Tested on Asus P8H61-M PRO, still boots.
Change-Id: I8a4900f8e3acffe4e4d75a51a2588ad6b65eb411
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The byte-wise error mask only needs to be set for certain corner cases
in read MPR training. Thus, minimize writes to this register.
Tested on Asus P8H61-M PRO, still boots.
Change-Id: I0bb8d99ad60c4964f896d303878e5982ae1dcdbe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Create and rename a few functions to contain the entire JEDEC write
leveling algorithm. Not all write training is JEDEC write leveling.
Tested on Asus P8H61-M PRO, still boots.
Change-Id: Ie9c6315340164029e30354723b4103d906633602
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
There's no need to reprogram the exact same sequence over a hundred
times. Move it out of the timB loop, and drop the `test_timB` function.
Tested on Asus P8H61-M PRO, still boots.
Change-Id: I375e325cf8b5369889b9cb059c3675cd00bdbb3f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Given that it sets the receive enable mode bit in the GDCRTRAININGMOD
register, it's clear that this is about receive enable calibration.
Remove a potentially-outdated comment. Proper documentation will be
written once code refactoring and various improvements are complete.
Change-Id: Iaefc8905adf2878bec3b43494dc53530064a9f5d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47576
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to run a write leveling test, one needs to unset the Qoff bit
in MR1, then run the test, and finally set Qoff again. The current IOSAV
sequence uses two subsequences to perform the test, while the other two
are unused. It is possible to perform the two necessary MR1 updates in
the same sequence, which can potentially improve runtime (not measured).
Since `write_mrreg` is no longer used, it is necessary to handle address
mirroring explicitly. This can be accomplished with the recently-added
`ddr3_mirror_mrreg` function, which is also used in `write_mrreg`.
Tested on Asus P8H61-M PRO, still boots.
Change-Id: I65ca1aa32cdb177d2a9e27c3b02e74ac0c882794
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47614
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
AMD family 17h and newer don't use cache as RAM, since the RAM is
already initialized by the PSP when the x86 cores are released from
reset. Therefore they use a different linker script as the rest of the
x86 chips in coreboot do. Since there will be support for newer
generations than Picasso will be added, move those linker scripts from
soc/amd/picasso to soc/amd/common/block/cpu/noncar.
TEST=Timeless build of amd/mandolin and amd/gardenia result in identical
binaries.
Change-Id: Ie60372aa498b6e505708f97213b502c9d0b3534b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This patch adds a new CBFS "mcache" (metadata cache) -- a memory buffer
that stores the headers of all CBFS files. Similar to the existing FMAP
cache, this cache should reduce the amount of SPI accesses we need to do
every boot: rather than having to re-read all CBFS headers from SPI
flash every time we're looking for a file, we can just walk the same
list in this in-memory copy and finally use it to directly access the
flash at the right position for the file data.
This patch adds the code to support the cache but doesn't enable it on
any platform. The next one will turn it on by default.
Change-Id: I5b1084bfdad1c6ab0ee1b143ed8dd796827f4c65
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Updating from commit id 4c523ed1:
vboot2: Add support for modexp acceleration
to commit id 9d4053df:
Revert "Reland: Clean up implicit fall through."
This brings in 32 new commmits. Among the changes are restored support
for older GCC/clang versions that do not support
__attribute__((fallthrough)).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I1110664bf71b4376bcdd9ba934a95031ba872c1d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Create the gumboz variant of the dalboz reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:173536689
BRANCH=zork
TEST=util/abuild/abuild -p none -t google/zork -x -a
make sure the build includes GOOGLE_GUMBOZ
Change-Id: I48db7eba7864c18e7307b45fe9f84073bfca0155
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
As a part of trying to get our boot time as low as possible, any delays
in the code should try to be refactored out. This removes the 50ms
delay in the WIFI sequence by enabling power and putting the wifi module
into reset in bootblock, then bringing it out of reset in ramstage.
This is significantly longer than the 50ms requirement. The reset GPIO
was already being set high in ramstage, so that code didn't need to be
added.
BUG=b:171513520
TEST=Boot on boards with different module types, WIFI works on both.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I211d3da338ad368d1f011f03cf7d05121c057075
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Currently, the PCIe bridge 00:15.2 is not detected by coreboot, causing
the connected network device also to be missing.
This is caused by not configuring the third of the four PCIe General
Purpose Ports (GPP) of the AMD Fusion Controller Hub (FCH), which can be
exposed as one to four PCIe devices.
So, enable it in AGESA but disable enumeration in coreboot. Otherwise,
the serial console stops working in romstage after
[…]
PCI: 00:15.1 bridge ctrl <- 0013
PCI: 00:15.1 cmd <- 06
PCI: 00:15.2 bridge ctrl <- 0013
PCI: 00:15.2 cmd <- 07
and the system hangs in the payload (SeaBIOS banner is shown on VGA
attached monitor).
TEST=Serial console and payload works, and Linux 5.10-rc2 configures
PCIe bridge. Output of `lspci -t`:
-[0000:00]-+-00.0
+-00.2
+-01.0
+-01.1
+-10.0
+-10.1
+-11.0
+-12.0
+-12.2
+-13.0
+-13.2
+-14.0
+-14.2
+-14.3
+-14.4-[01]--
+-14.5
+-15.0-[02]--
+-15.1-[03]----00.0
+-15.2-[04]----00.0
+-18.0
+-18.1
+-18.2
+-18.3
+-18.4
\-18.5
Change-Id: Ia1d60a212b0d249c7d8b3f8ec16baf5e93c985da
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46527
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The idea is to split the “mainboard” category into “variants” and
“carrierboards”, in the case when we use the COMe module together
with the Carrier Board instead of a single monolithic motherboard.
Previously, the “variants” category defined the type of motherboard,
which has a number of differences from the base one, for example, it
differed in the size or type of memory, and in the configuration of
the interfaces. Thus, there is no need to create a separate directory
in src/mainboard for a board that is similar in configuration to the
base board. But for a COMe module, “variants” contains different
variants of only this module, and the entire Carrier Board configuration
is allocated to a separate category - “carrierboards”, and each of the
variants can be used with one of the many boards in “carrierboards”.
For example, in the case of the Kontron mAL10 COMe module, variant
refers to the COMe-mAL10 or COMe-m4AL10 module type. They differ in the
type of memory (DDR3L or DDR4), and maybe they differ in some chips (see
more in https://www.kontron.com/products). However, all variants contain
the same type of processor/SoC.
The "carrierboards" directory can be able contain both the Kontron's
Evalution carrier boards (such as Eval Carrier2 T10 and COMe
Ref.Carrier-i T10 TNI) and third party vendor backplanes that are
compatible with the COMe modules from “variants”.
Thus, the src/mainboard/<module-name> directory contains the common
configuration code for all variants from src/mainboard/<module-name>/
variants, which can be supplemented/redefined with a configuration from
src/mainboard/<module-name>/carrierboard/<vendor-carrierboard-name>.
This architectural solution will be able to systematize and simplify
understanding of the code structure for COMe modules and will allow
vendors to add/maintain their code in a separate directory.
This work is also the first step towards to union of all carrierboards
into the global category in src/carrierboard on a par with all boards
from src/mainboard.
The patch takes this into account in the build system and adds
CARRIER_DIR component to use the “carrierboards” category, as it has
done for VARIANT_DIR.
TEST = Build ROM image for Kontron mAL10 COMe module together with T10
TNI carrier board (https://review.coreboot.org/c/coreboot/+/39133).
Change-Id: Ic6b2f8994b1293ae6f5bda8c9cc95128ba0abf7a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42609
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Expose a config option that allows disabling the FSP UPD which controls
Precision Time Measurement for a particular PCIe root port. Since this
is enabled by default the option is inverted to allow disabling for
a particular port while not affecting others.
BUG=b:160996445
TEST=boot on volteer with PTM disabled for the NVMe root port
Change-Id: Icb51b256eb581d942b2d30fcabfae52fa90e48d4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
The device acceptable latency field is only valid for 'endpoints',
but not for bridge devices. Set the maximum acceptable latency on
such devices to allow ASPM being enabled if supported on both sides.
Allows the PCIe link on bridge devices to go into L0s/L1.
This allows the package to enter a deeper sleep state when all links
are idle.
WARNING: This might cause issues on PCIe bridge devices that doesn't
properly support ASPM. In addition it might decrease performance.
Change-Id: I277efe0bd1448ee8bff633428aa729aeedf04e28
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
The virtual/generic device under TBT PCIe root ports has path type as
DEVICE_PATH_GENERIC. While scanning the pcie bus, the generic device
blocks its root ports configuration. This change adds device path type
check and enables ASPM for TBT root ports.
BUG=b:173207454
TEST=Built image and booted to kernel on Voxel board. Verified both of
the TBT Root ports 00:07.0 and 00:07.1 ASPM are enabled.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I82ffaeb5a8821d9034d8dae9d98d3b5953a9608b
Replace the two obsolete LPID implementations with the new PEPD device.
The PEPD device gets included in the plaforms' `southbridge.asl`, since
it is required to load the `intel_pmc_core` module in Linux, which
checks for the _HID. (See CB:46469 for more info on that.)
There is no harm for mainboards not supporting S0ix, because the _DSM
function won't be called with the LPS0 UUID on such boards. Such boards
can use the debugging functionality of `intel_pmc_core`, too.
Change-Id: Ic8427db33286451618b50ca429d41b604dbb08a5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Add the _HID INT33A1 to PEPD to make Linux recognize it as "Intel Power
Engine" in the pmc core driver.
The _ADR gets dropped, because _HID and _ADR are mutually exclusive.
Change-Id: I7a0335681f1601f7fd8a9245a3dea72ffd100b55
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
The PEPD enum function returns a bitmask to announce supported/enabled
PEPD functions. Add a comment describing this bitmask and correct the
return value to announce function 1, 5 and 6 as supported.
Also add comments to the disabled functions 3 and 4.
Change-Id: Ib523a54f5ad695e79005aba422282e03f2bc4bed
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Windows does not comply with the Low Power Idle S0 specification and
crashes with an `INTERNAL_POWER_ERROR` bluescreen when function 1, does
not return at least one device constraint, even when function 1 is
announced as being not available by the enum function. Returning an
empty package does not work.
At least the following Windows versions were verified to be affected:
- Windows 8.1 x64, release 6.3.9600
- Windoes 10 x64, version 1809, build 17763.379
- Windows 10 x64, version 1903, build 18362.53
- Windows 10 x64, version 2004, build 19041.508
- Windows 10 x64, version 20H2 / 2009, build 19042.450
To make Windows work on S0ix-enabled boards, return a dummy constraint
package with a disabled dummy device.
Since the device constraints are only used for debugging low power
states in Linux and probably also in Windows, there shouldn't be any
negative effect to S0ix. Real device constraint entries could be added
at a later point, if needed.
Note: to fully prevent the BSOD mentioned above the LPIT table is
required on Windows, too. The patch for this is WIP, see CB:32350.
If you want to test this, you need to applie the whole ACPI patch
series including the hacky LPIT test implementation from CB:47242:
https://review.coreboot.org/q/topic:%22low_power_idle_fix%22
Test: no bluescreen anymore on Clevo L140CU on all Windows versions
listed above and S0ix gets detected in `powercfg -a`.
Change-Id: Icd08cbcb1dfcb8cbb23f4f4c902bf8c367c8e3ac
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
PEPD function 2 is currently unused and disabled. Thus, drop the return
value, which matches the default return value.
Change-Id: Ia95b8b36fcb78e8976b66de15ec214a38c178cda
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
`ARG2` in the macro's names does not really provide any useful
information. Drop it and add `LPI` to clarify the relation to only
low-power idle states.
Change-Id: I8d44c9e4974c7f34aa5c32ba00328725f536fda6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Rename LPID to PEPD for consistency. PEPD means "Power Engine Plug-In
Device" and is the name Intel and vendors usually use, so let's comply.
Change-Id: I1caa009a3946b1c55da8afbae058cafe98940c6d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Move the UUID to the condition, since there is no need to assign a name
when it is only used once. Also add a comment to make clear that the
functions inside that condition are only used by the Low Power Idle S0
functionality, while the PEPD in general can be present on boards
without S0ix capability, too. For details check CB:46469.
Change-Id: Ic62c37090ad1b747f9d7d204363cc58f96ef67ef
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
PEPD will get included directly in the southbridge. Thus, drop the
scope around it.
Change-Id: Icb7a40e476966a7aca36bee055ee71d181508b87
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
The various platform BARs are not always the same size across different
SOCs, so use the defined size rather than a hardcoded value.
This results in the following change on TGL which increased the MCHBAR
size to 128K:
-system 00:00: [mem 0xfedc0000-0xfeddffff] has been reserved
+system 00:00: [mem 0xfedc0000-0xfedc7fff] has been reserved
And fixes the following error output from the kernel:
resource sanity check: requesting [mem 0xfedc0000-0xfedcdfff],
which spans more than pnp 00:00 [mem 0xfedc0000-0xfedc7fff]
Change-Id: I82796c2fc81dec883f3c69ae7bdcedc7d3f16c64
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Enable SOC_INTEL_COMMON_BLOCK_GPIO_IOSTANDBY so the pads can be
configured with non-zero IOSSTATE values.
BUG=b:171993054
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I1f895dbdbb71a353a98272db6dc70b54e8e172a3
This SOC overrides the common PMC device and instantiates the PMC device
in the SSDT. It needs to call the common PMC function to provide the
IPC mailbox method.
The common PCIe RTD3 driver can also be enabled which will allow
mainboards to enable Runtime D3 power control for PCIe devices.
BUG=b:160996445
TEST=boot on volteer with this driver enabled for the NVMe device in the
devicetree and disassemble the SSDT to ensure the RTD3 code is present.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: Ifa54ec3b8cebcc2752916cc4f8616fcb6fd2fecc
This driver is for devices attached to a PCIe root port that support
Runtime D3. It creates the necessary PowerResource in the root port to
provide _ON/_OFF methods for which will turn off power and clocks to the
device when it is in the D3cold state.
The mainboard declares the driver in devicetree and provides the GPIOs
that control power/reset for the device attached to the root port and
the SRCCLK pin used for the PMC IPC mailbox to enable/disable the clock.
An additional device property is created for storage devices if it
matches the PCI storage class which is used to indicate that the storage
device should use D3 for power savings.
BUG=b:160996445
TEST=boot on volteer device with this driver enabled in the devicetree
and disassemble the SSDT to ensure this code exists.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I13e59c996b4f5e4c2657694bda9fad869b64ffde
Upstream has converted all uses of SUBSYSTEM_{VENDOR,DEVICE}_ID in
Kconfig to subsystemid in devicetree. It will soon produce a lint error
from Jenkins [1].
[1]: https://review.coreboot.org/c/coreboot/+/45513/
Change-Id: I66d5d5f23d3c8ab6ed79dad432a0773841147eea
Signed-off-by: Tim Crawford <tcrawford@system76.com>
On PCH-H the I2C4 0:19.0 device isn't usable and thus 0:19.1 and
0:19.2 can't be detected using standard PCI probing.
Remove I2C4, I2C5 and UART2 from generic ASL code on PCH-H platforms
that advertise its PCI conformance by the _ADR attribute.
Change-Id: I89f9ab7d4afb2e7d1b1e24d072adf99e0da6fecf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Following up 3ccae2b7, this patch adds Iccmax and AC/DC
loadlines and iPL2 for CML-S CPUs. The information is from
CML EDS volume 1, doc #606599 and pdg #610244.
Change-Id: Id2797a979a8b6a52a34baae66f95c7136ed1dc72
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Fixes FSP not finding a valid framebuffer on reboots, which resulted in
a black screen when running the edk2 payload.
Change-Id: I946adb0657c07cf6c5a9aeb369e4fdfd8826abb2
The USB table in the manuals incorrectly list the USB3 port as 5.
The labeled pins show it correctly as port 2.
Change-Id: I9a6a96af847ca66ad667738d83cfca7c3166956a
* Move most mainboard/system76 ACPI code to ec/system76
* Move drivers/system76_ec to ec/system76
* Include system76_ec.c when CONSOLE_SYSTEM76 is set
* Fix inclusion of system76 EC code
* Default CONSOLE_SYSTEM76_EC to n
* addw2: fix SSD2 clkreq
The System76 Lemur Pro (lemp9) is an upcoming laptop computer. Support
in coreboot is developed by System76 and provided as the default
firmware option. Testing is done on a pre-production model expected to
be identical from a firmware perspective to the production model.
Working:
- Payload
- Tianocore
- CPU
- Intel i7-10510U
- Intel i5-10210U
- EC
- ITE IT5570E running https://github.com/system76/ec
- Backlit Keyboard, with standard PS/2 keycodes and SCI hotkeys
- Battery
- Charger, using AC adapter or USB-C PD
- Suspend/resume
- Touchpad
- GPU
- Intel UHD Graphics 620
- GOP driver is recommended, VBT is provided
- eDP 14-inch 1920x1080 LCD
- HDMI video
- USB-C DisplayPort video
- Memory
- 8-GB DDR4 Samsung K4AAG165WA-BCTD (Channel 0)
- 8-GB/16-GB/32-GB DDR4 SO-DIMM (Channel 1)
- Networking
- M.2 PCIe/CNVi WiFi/Bluetooth
- Sound
- Realtek ALC293D
- Internal speaker
- Internal microphone
- Combined headphone/microphone 3.5-mm jack
- HDMI audio
- USB-C DisplayPort audio
- Storage
- M.2 PCIe/SATA SSD-1
- M.2 PCIe/SATA SSD-2
- RTS5227S MicroSD card reader
- USB
- 1280x720 CCD camera
- USB 3.1 Gen 2 Type-C (left)
- USB 3.1 Gen 2 Type-A (left)
- USB 3.1 Gen 1 Type-A (right)
Not working:
- TPM2 - SPI bus 0, chip select 2 is used. Chip selects other than 0
are not currently supported by the intel fast_spi driver.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ib0a32bbc6f89a662085ab4a254676bc1fad7dc60
This change adds support for allocating resources for PCI express hotplug
bridges when PCIEXP_HOTPLUG is selected. By default, this will add 32 PCI
subordinate numbers (buses), 256 MiB of prefetchable memory, 8 MiB of
non-prefetchable memory, and 8 KiB of I/O space to any device with the
PCI_EXP_SLTCAP_HPC bit set in the PCI_EXP_SLTCAP register, which
indicates hot-plugging capability. The resource allocation is configurable,
please see the PCIEXP_HOTPLUG_* variables in src/device/Kconfig.
In order to support the allocation of hotplugged PCI buses, a new field
is added to struct device called hotplug_buses. This is defaulted to
zero, but when set, it adds the hotplug_buses value to the subordinate
value of the PCI bridge. This allows devices to be plugged in and
unplugged after boot.
This code was tested on the System76 Darter Pro (darp6). Before this
change, there are not enough resources allocated to the Thunderbolt
PCI bridge to allow plugging in new devices after boot. This can be
worked around in the Linux kernel by passing a boot param such as:
pci=assign-busses,hpbussize=32,realloc
This change makes it possible to use Thunderbolt hotplugging without
kernel parameters, and attempts to match closely what our motherboard
manufacturer's firmware does by default.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I500191626584b83e6a8ae38417fd324b5e803afc
This implements soc_display_fspm_upd_params for soc/intel/cannonlake
Some parameters are available only on Coffee Lake FSP or Comet Lake FSP
Tested on System76 galp3-c (Coffee Lake FSP) and System76 galp4 (Comet
Lake FSP)
This fixes the following:
- Fix smmstore_read_region to actually read stuff
- Make the API ARCH independent (no dependency on size_t)
- clean up the code a little
- Change the loglevel for non error messages to BIOS_DEBUG
Change-Id: I629be25d2a9b65796ae8f7a700b6bdab57b91b22
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
2019-05-02 15:24:13 -06:00
883 changed files with 45987 additions and 13410 deletions
@@ -75,7 +75,8 @@ be more frequent than was needed, so we scaled it back to twice a year.
- [ ] Test the release from the actual release tarballs.
- [ ] Push signed Tag to repo.
- [ ] Announce that the release tag is done on IRC.
- [ ] Upload release files to web server
- [ ] Upload release files to web server.
- [ ] Also extract the release notes and place them on the web server.
- [ ] Upload crossgcc sources to web server.
- [ ] Update download page to point to files, push to repo.
- [ ] Write and publish blog post with release notes.
@@ -197,16 +198,16 @@ the coreboot server, and put them in the release directory at
````
People can now see the release tarballs on the website at
https://www.coreboot.org/releases/
<https://www.coreboot.org/releases/>
The downloads page is the official place to download the releases from, and it needs to be updated with links to the new release tarballs and .sig files. It can be found at https://review.coreboot.org/cgit/homepage.git/tree/downloads.html
The downloads page is the official place to download the releases from, and it needs to be updated with links to the new release tarballs and .sig files. It can be found at <https://review.coreboot.org/cgit/homepage.git/tree/downloads.html>
Here is an example commit to change it: https://review.coreboot.org/#/c/19515/
Here is an example commit to change it: <https://review.coreboot.org/c/homepage/+/19515>
## Upload crossgcc sources
Sometimes the source files for older revisions of
crossgcc disappear. To deal with that we maintain a mirror at
https://www.coreboot.org/releases/crossgcc-sources/ where we host the
<https://www.coreboot.org/releases/crossgcc-sources/> where we host the
sources used by the crossgcc scripts that are part of coreboot releases.
Run
@@ -220,7 +221,7 @@ sources. Download them yourself and copy them into the crossgcc-sources
directory on the server.
## After the release is complete
Post the release notes on https://blogs.coreboot.org
Post the release notes on <https://blogs.coreboot.org>
## Making a branch
At times we will need to create a branch, generally for patch fixes.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
