Begin rewriting the ACPI support according to the Design Guide.
Partially implements Low Power States and GPU Boost methods.
Change-Id: I119f3206685ad337dcbb73d55cc807d00d5659fb
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The addw1 supports an i9-9980HK and the addw2 uses an i7-10875H.
These CPUs have 8 cores and 16 threads. Fixes booting on addw2.
Change-Id: I4639b40c3ab9c6d6ad5abbbb3618c750c7d40695
Fixes: 6a93a45242 ("mb/system76/addw1: Add System76 Adder Workstation 1")
Signed-off-by: Tim Crawford <tcrawford@system76.com>
The option table is shrunk 1 byte to force coreboot to invalid the table
and write the new defaults. This will ensure the IME is in the correct
mode on the next update.
Change-Id: I805c53fee55fea69fa3363fea0609858cc88f2d3
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Add CMOS option to set IME mode. Default to "Disable" for CNL and TGL-H,
and "Enable" for TGL-U. Not set for KBL, which uses ME_CLEANER.
The HECI device must be enabled in devicetree for switching modes to
function correctly.
Change-Id: I3163dcb0a4af020c2cf6f94f2bb26380f17c253e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Add .enable method that will set the CSME state. The state is based on
the new CMOS option me_state, with values of 0 and 1. The method is very
stable when switching between different firmware platforms.
This method should not be used in combination with USE_ME_CLEANER.
State 1 will result in:
ME: Current Working State : 4
ME: Current Operation State : 1
ME: Current Operation Mode : 3
ME: Error Code : 2
State 0 will result in:
ME: Current Working State : 5
ME: Current Operation State : 1
ME: Current Operation Mode : 0
ME: Error Code : 0
Tested on:
KBL-R: i7-8550u
CML: i3-10110u, i7-10710u
TGL: i3-1110G4, i7-1165G7
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I374db3b7c0ded71cdc18f27970252fec7220cc20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add a driver for systems with NVIDIA Optimus (hybrid) graphics using
GC6 3.0. The driver provides ACPI support for dynamically powering on
and off the GPU, and a function for enabling the GPU power in romstage.
Tested on system76/gaze15.
Change-Id: I2dec7aa2c8db7994f78a7cc1220502676e248465
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Software Connection Manager doesn't work with Linux 5.13 or later and
results in TBT ports timing out. Not advertising this results in
Firmware Connection Manager being used and TBT works correctly.
Linux patch:
c6da62a219
Tested on:
* StarBook Mk V
* System76 Oryx Pro 8
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ib947c3c9cd843e54d4664509c15336178c0bc99e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
1. Turn off L2C SRAM and reconfigure as L2 cache
Mediatek SoC uses part of the L2 cache as SRAM before DRAM is ready.
After DRAM is ready, we should invoke disable_l2c_sram to reconfigure
the L2C SRAM as L2 cache.
2. Configure DMA buffer in DRAM
Set DRAM DMA to be non-cacheable to load blob correctly.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: If56d29cdd7d9dfaed05e129754aa1f887a581482
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
CONFIG(SMP) was an invalid condition to use in cases where one
stage requires spinlocks and another one does not. The
stage not requiring spinlock still required <smp/spinlock.h>
to be implemented with no-op stubs.
This reverts commit 037ee4b556
soc/amd/picasso: Add dummy spinlock for psp_verstage
Change-Id: Iba52febdeee78294f916775ee9ce8a82d6203570
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add separate gpio table for early eSPI bus init. Remove espi GPIO from
early_gpio_table. This allows for initializing eSPI separately from
other GPIOs. Simplify verstage_mainboard_early_init.
BUG=b:200578885
BRANCH=None
TEST=Build and boot guybrush
Change-Id: I0cd439f207df7c27575ae363b207293d40485bf8
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
This change adds about 30 KiB to FSP-M. When not using the SPI DMA
controller, this change actually has a ~7 ms boot time penalty. When
we use the DMA engine, we end up with about a 5 ms decrease. Once we
switch to 100 MHz SPI this will help even more since we have effectively
eliminated the decompression time.
BUG=b:179699789
TEST=Boot nipperkin to OS and take boot time measurements
fspm.bin 0x2efc0 fsp 90953 LZMA (233472 decompressed)
fspm.bin 0x2cfc0 fsp 121156 LZ4 (233472 decompressed)
- FSP-M / no async -
| 508 - finished loading body | 177.019 | 179.384 Δ( 2.36, 0.16%) |
...
| 970 - loading FSP-M | 0.346 | 0.346 Δ( 0.00, 0.00%) |
| 17 - starting LZ4 decompress (ignore for x86) | 0.009 | 0.01 Δ( 0.00, 0.00%) |
| 18 - finished LZ4 decompress (ignore for x86) | 53.916 | 59.475 Δ( 5.56, 0.37%) |
- FSP-M / async -
| 508 - finished loading body | 177.185 | 179.689 Δ( 2.50, 0.18%) |
...
| 970 - loading FSP-M | 0.989 | 0.99 Δ( 0.00, 0.00%) |
| 17 - starting LZ4 decompress (ignore for x86) | 9.483 | 12.877 Δ( 3.39, 0.24%) |
| 18 - finished LZ4 decompress (ignore for x86) | 10.833 | 0.312 Δ(-10.52, -0.75%) |
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I7d0363d27d98d4ed3afc6f802a13ff7986391921
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Calling reboot_into_recovery with NULL context fails. Initializing ctx
early also fails because the cmos is not ready until after
verstage_soc_early_init. So just reboot and hope for the best.
BUG=None
TEST=Boot guybrush, suspend/resume guybrush
BRANCH=None
Change-Id: I7267a14ab048781b8998d3a6f4220de10e7df250
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The 64-bit compiler x86_64-linux-gnu-gcc-10 aborts the build with the format
warning below:
CC romstage/soc/intel/xeon_sp/memmap.o
src/soc/intel/xeon_sp/memmap.c: In function 'fill_postcar_frame':
src/soc/intel/xeon_sp/memmap.c:39:62: error: format '%lx' expects argument of type 'long unsigned int', but argument 4 has type 'size_t' {aka 'unsigned int'} [-Werror=format=]
39 | printk(BIOS_DEBUG, "cbmem base_ptr: 0x%lx, size: 0x%lx\n", cbmem_base, cbmem_size);
| ~~^ ~~~~~~~~~~
| | |
| long unsigned int size_t {aka unsigned int}
| %x
As `cbmem_size` is of type `size_t` use the appropriate length modifier
`z`.
Change-Id: I1ca77de1ce33ce1e97d7c8895c6e75424f0769f5
Found-by: gcc (Debian 11.2.0-10) 11.2.0
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Lance Zhao
Do not place console output in low-level GPIO functions.
The caller of get_recovery_mode_switch() is in vboot_logic.c
that is linked in romstage. So presumably recovery mode
is broken and is not fixed with this commit either.
Change-Id: I2a0fdbb370d54898c72adb29a0e9b990a5fc0ce1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add APU device apc driver and set up permissions.
APU has its own device apc for control access by domains.
For Domain 0, the access to the following slaves are restricted to
security read and write:
apusys_ao-2, apusys_ao-4, apusys_ao-5, apu_sctrl_reviser,
apu_iommu0_r1 apu_iommu0_r2, apu_iommu0_r3, apu_iommu0_r4
apu_iommu1_r1, apu_iommu1_r2, apu_iommu1_r3,apu_iommu1_r4
For VPU, D0/D5 are set as no protection, other domains are forbidden.
For other slaves, the D0 is no protection, other domains are forbidden.
BUG=b:203145462
BRANCH=cherry
TEST=boot cherry, check dump log and test permissions
Signed-off-by: Flora Fu <flora.fu@mediatek.com>
Change-Id: If92d3b02ac4966332315b85d68e0f48c6a9fce85
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
FSP-S is normally memmapped and then decompressed. There are about 7 ms
between starting ramstage, and loading FSP-S. By preloading we can
ensure the fsps.bin is already in RAM by the time we need it. This
reduces boot time by about 7 ms.
BUG=b:
TEST=Boot nipperkin and see ~7ms reduction in boot time
| 10 - start of ramstage | 0.044 | 0.044 Δ( 0.00, 0.00%) |
| 30 - device enumeration | 1.899 | 2.073 Δ( 0.17, 0.01%) |
| 971 - loading FSP-S | 6.645 | 6.628 Δ( -0.02, -0.00%) |
| 15 - starting LZMA decompress (ignore for x86) | 0.016 | 0.01 Δ( -0.01, -0.00%) |
| 16 - finished LZMA decompress (ignore for x86) | 15.266 | 8.316 Δ( -6.95, -0.47%) |
| 954 - calling FspSiliconInit | 0.08 | 0.09 Δ( 0.01, 0.00%) |
CBFS DEBUG: _cbfs_alloc(name='fsps.bin', alloc=0xc9761e5c(0xc97a3f0c), force_ro=false, type=-1)
CBFS: Found 'fsps.bin' @0x1a1fc0 size 0x102cd in mcache @0xc97dd208
waiting for thread
took 1 us <-- fsps.bin was preloaded
CBFS DEBUG: get_preload_rdev(name='fsps.bin') preload successful
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5a728047b8ad92d70bba8485017579aa3df48d95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
This will enable reading FSP-S/M using the SPI DMA controller.
BUG=B:179699789
TEST=Build guybrush with SPI DMA enabled and verify alignment is set
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I282b9989d8e95c93603c6f69616a8f236a4e2e35
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Used H1 firmware where the last version number is 0.0.22, 0.3.22 or
less to production that will need to disable autonomous GPIO power
management and then can get H1 version by gsctool -a -f -M
BUG=b:201054849
TEST=USE="project_primus emerge-brya coreboot" and verify it builds
without error.
Change-Id: If5a99a96e5d4b84be3f2c1165283ce249ca75d58
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Make the `codec_init()` function non-static so that it can be used in
other places. Rename it to `azalia_codec_init()` for consistency with
the other functions of the API.
Also, update the function's signature to make it more flexible. Remove
the unused `dev` parameter and allow callers to pass the verb table to
use. Update the original call site to preserve behavior.
Change-Id: I5343796242065b5fedc78cd95bcf010c9e2623dd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59117
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make the `codecs_init()` function non-static so that it can be used in
other places. Rename it to `azalia_codecs_init()` to avoid name clashes
with static definitions in southbridge code (which will be removed in
subsequent commits).
Change-Id: I080a73102b0c4f9f8a283cd93bba9b3b23169be0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
For consistency with other Intel southbridges, program PC BEEP verbs.
None of the boards in the tree using this southbridge provide PC BEEP
verbs, so this change makes no difference.
Change-Id: I94d24999af819cf3951510586fd4864d1ed3f2f1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Use the `azalia_program_verb_table()` function in preparation to
deduplicate Azalia init code.
With this change, the "Azalia: verb loaded." message is now printed when
programming the verbs failed. This will be addressed once `codec_init()`
has been deduplicated.
Change-Id: I5d9e0f19429620166f2a6ef48ec7c963ee64b59c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59105
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Currently all the power sequencing for FPMCU is done explicitly in
different stages of coreboot. This can all be done by adding ACPI power
resources for FPMCU and clean up the unused code. Here is the expected
power sequence:
PowerUp : Assert EN_PWR_FP -> 3 ms delay -> De-assert FPMCU_RST_ODL
Shutdown : De-assert EN_PWR_FP -> Assert FPMCU_RST_ODL
Reboot : Shutdown -> 200 ms delay -> PowerUp
BUG=None
TEST=Build and boot to OS in Guybrush. Ensure that the FP is able to
unlock the system after the first login attempt. Ensure that the FP is
able to wakeup the system. Observed that the power resource is added
correctly in the FPMCU ACPI object
Name (_PR0, Package (0x01) // _PR0: Power Resources for D0
{
PR01
})
Name (_PR3, Package (0x01) // _PR3: Power Resources for D3hot
{
PR01
})
PowerResource (PR01, 0x00, 0x0000)
{
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x01)
}
Method (_ON, 0, Serialized) // _ON_: Power On
{
\_SB.CTXS (0x0B)
\_SB.STXS (0x20)
\_SB.STXS (0x0B)
}
Method (_OFF, 0, Serialized) // _OFF: Power Off
{
\_SB.CTXS (0x0B)
\_SB.CTXS (0x20)
}
}
Change-Id: I52322eaecf6961ff9a196ca9ab2d58b7d4599d4f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
We need to put USB setting in mux order.
BUG=b:204230406
TEST=Type C mux configuration is correct.
Wrong:
added type-c port0 info to cbmem: usb2:2 usb3:2 sbu:0 data:0
added type-c port1 info to cbmem: usb2:3 usb3:3 sbu:0 data:0
Correct:
added type-c port0 info to cbmem: usb2:3 usb3:3 sbu:0 data:0
added type-c port1 info to cbmem: usb2:2 usb3:2 sbu:0 data:0
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I19338e162db6145dbeb5830de1a372cf98f779a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Add wifi sar for galtic/galtic360/galith360
Using convertible mode of SKU ID to load wifi table.
Each Project and SKU ID correspond as below
galtic (sku id:0x120000)
galith (sku id:0x130000)
gallop (sku id:0x150000)
galtic360 (sku id:0x260000)
galith360 (sku id:0x270000)
BUG=b:203741126
TEST=emerge-dedede coreboot chromeos-bootimage \
coreboot-private-files-baseboard-dedede
verify the SAR table is correct in each project
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: If4203d176dd717fa62c88d9b4fab8a53847213fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
List of changes:
1. Create Module Type macros as per Memory Type
(i.e. DDR2/DDR3/DDR4/DDR5/LPDDR4/LPDDR5) and fix compilation
issue due to renaming of existing macros due to scoping the Memory
Type.
2. Use dedicated Memory Type and Module type for `Form Factor`
and `TypeDetail` conversion using `get_spd_info()` function.
3. Create a new API (convert_form_factor_to_module_type()) for
`Form Factor` to 'Module type' conversion as per `Memory Type`.
4. Add new argument as `Memory Type` to
smbios_form_factor_to_spd_mod_type() so that it can internally
call convert_form_factor_to_module_type() for `Module Type`
conversion.
5. Update `test_smbios_form_factor_to_spd_mod_type()` to
accommodate different memory types.
6. Skip fixed module type to form factor conversion using DDR2 SPD4
specification (inside dimm_info_fill()).
Refer to datasheet SPD4.1.2.M-1 for LPDDRx and SPD4.1.2.L-3 for DDRx.
BUG=b:194659789
TEST=Refer to dmidecode -t 17 output as below:
Without this code change:
Handle 0x0012, DMI type 17, 40 bytes
Memory Device
Array Handle: 0x000A
Error Information Handle: Not Provided
Total Width: 16 bits
Data Width: 16 bits
Size: 2048 MB
Form Factor: Unknown
....
With this code change:
Handle 0x0012, DMI type 17, 40 bytes
Memory Device
Array Handle: 0x000A
Error Information Handle: Not Provided
Total Width: 16 bits
Data Width: 16 bits
Size: 2048 MB
Form Factor: Row Of Chips
....
Change-Id: Ia337ac8f50b61ae78d86a07c7a86aa9c248bad50
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
We are currently counting how long it takes to print the waiting
message, in addition to the actual time we spent waiting. This results
in inflating the measurement by 1.7ms when the serial console is
enabled. This CL makes it so the print happens before the stopwatch
starts.
BUG=b:179699789
TEST=No longer see printk time taken into account on serial console
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib48e37c1b2cb462d634141bf767673936aa2dd26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Currently, the MMCONF Kconfigs only support the Enhanced Configuration
Access mechanism (ECAM) method for accessing the PCI config address
space. Some platforms have a different way of mapping the PCI config
space to memory. This patch renames the following configs to
make it clear that these configs are ECAM-specific:
- NO_MMCONF_SUPPORT --> NO_ECAM_MMCONF_SUPPORT
- MMCONF_SUPPORT --> ECAM_MMCONF_SUPPORT
- MMCONF_BASE_ADDRESS --> ECAM_MMCONF_BASE_ADDRESS
- MMCONF_BUS_NUMBER --> ECAM_MMCONF_BUS_NUMBER
- MMCONF_LENGTH --> ECAM_MMCONF_LENGTH
Please refer to CB:57861 "Proposed coreboot Changes" for more
details.
BUG=b:181098581
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_KOHAKU -x -a -c max
Make sure Jenkins verifies that builds on other boards
Change-Id: I1e196a1ed52d131a71f00cba1d93a23e54aca3e2
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add documentation describing how to add support for a new memory
technology to spd_tools:
- Add a section to the README.
- Document the memTech interface in spd_gen.go.
BUG=b:191776301
TEST=None
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Ie710c1c686ddf5288db35cf43e5f1ac9b1974305
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59005
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In both the Picasso PPR (rev 3.16) and the Cezanne PPR (rev 3.03) bit 16
of the misc I2C pad control registers is defined as BiasCrtEn, so rename
I2C_PAD_CTRL_BIOS_CRT_EN to I2C_PAD_CTRL_BIAS_CRT_EN.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If39ac17a433cb90c944fdde038cd246a995e193a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59028
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update charger performance control table of DPTF for bugzzy.
Since the EC change chromium:197776876 modified maximum charging current
to reduce skin temperature, this change adjusts the charging performance
table with the modified value.
BUG=b:197776876
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: I33e176fcf5d380b315ff352c6c65af3b8b93c4b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This drops VBOOT_NO_BOARD_SUPPORT.
There is little impact of always having recovery_mode_switch()
implemented in bootmode.c. A weak write_protect_state() is not
necessary as there is no BOOT_DEVICE_SPI_FLASH with the emulation.
Call to fill_lb_gpios() is already guarded with CONFIG(CHROMEOS)
so the weak implementation would not be referenced.
Change-Id: I3c00b30c5233ae3556b7622f97c3166668c8ab12
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This error prevented the last line of the Kconfig tree from being
printed or added to the output file. This is a significant problem if
you try to use the generated file as the kconfig source, because it
changes CONFIG_HAVE_RAMSTAGE from defaulting to yes to defaulting to
NO. This causes the build to stop working.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I3ec11f1ac59533a078fd3bd4d0dbee9df825a97a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Technically, it's not depending on the hardware but on the software
(OS/payload), if the PM Timer is optional. OSes with ACPI >= 5.0A
support disabling of the PM Timer, when the respective FADT flag is
unset. Thus, drop this guard.
For platforms without hardware PM Timer (Apollo Lake, Gemini Lake) the
Kconfig `USE_PM_ACPI_TIMER` depends on `!NO_PM_ACPI_TIMER`.
As of this change, new platforms must either implement code for
disabling the hardware PM timer or select `NO_PM_ACPI_TIMER` if no such
is present.
Change-Id: I973ad418ba43cbd80b023abf94d3548edc53a561
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lance Zhao
In the non-XIP world, FSP is normally memmapped and then decompressed.
The AMD SPI DMA controller can actually read faster than mmap. So by
reading the contents into a buffer and then decompressing we reduce boot
time.
BUG=b:179699789
TEST=Boot guybrush and see 30ms reduction in boot time
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I28d7530ae9e50f743e3d6c86a5a29b1fa85cacb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
AMD platforms pass in the base address to cbfs tool:
fspm.bin-options: -b $(CONFIG_FSP_M_ADDR)
There is no technical reason not to allow FSP-M to be relocated when
!XIP. By allowing this, we no longer need to pass in the base address
into cbfstool when adding fspm.bin. This enables passing in the
`--alignment` argument to cbfs tool instead. cbfstool currently has a
check that prevents both `-b` and `-a` from being passed in.
BUG=b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I797fb319333c53ad0bbf7340924f7d07dfc7de30
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The follow up CLs will use CBFS_PRELOAD. The default CBFS_CACHE_SIZE was
derived by examining the `cbfstool print` output and summing the files
we intend to preload.
BUG=b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I208067e6ceec6ffb602a87bee3bf99a0a75c822d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Add the parts below which will be used by the brya variant Vell. Add
the parts to memory_parts.json and generate the SPDs using spd_gen.
Micron MT62F512M32D2DR-031 WT:B
Micron MT62F1G32D4DR-031 WT:B
Hynix H9JCNNNCP3MLYR-N6E
Generated using:
util/spd_tools/bin/spd_gen spd/lp5/memory_parts.json lp5
BUG=b:204284866
TEST=None
Change-Id: Ifbcadfb78281b2b78a61a9b61180c421748193a0
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Read fw_config value from VPD.
This new option can be used where chrome EC is not supported like
pre-silicon platform and fw_config can be updated by VPD tool in OS.
TEST= boot to OS and read fw_config from vpd
1. Boot to OS
2. Write "fw_config" in VPD
ex) vpd -i "RW_VPD" -s "fw_config"="1"
3. reboot and check fw_config value from coreboot log
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I4df7d5612e18957416a40ab854fa63c8b11b4216
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Request fw_config values from various sources (as enabled via Kconfig)
until a valid value has been read.
With this change, Chrome EC CBI takes precedence over CBFS fw_config.
TEST=select both configs and check fallback behavior.
1. select both FW_CONFIG_SOURCE_CHROMEEC_CBI and FW_CONFIG_SOURCE_CBFS
2. check log for reading fw_config from CBI and CBFS
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I215c13a4fcb9dc3b94f73c770e704d4e353e9cff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
elog init requires doing a lot of SPI transactions. This change makes it
clear how long we spend initializing elog.
BUG=b:179699789
TEST=Boot guybrush and see elog init timestamps
114:started elog init 3,029,116 (88)
115:finished elog init 3,071,281 (42,165)
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia92372dd76535e06eb3b8a08b53e80ddb38b7a8f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58957
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This gives us a knob that can be controlled via a .config to
enable/disable file preloading. I left the option disabled because
there is currently a race condition that can cause data corruption when
using the SPI DMA controller. The fix will actually introduce a
boot time regression because the preloads are happening at the same time
as the elog init. I want to keep preloading disabled for now until
I get all the sequencing worked out.
BUG=b:179699789
TEST=Boot guybrush and verify no preloading happens.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ie839e54fa38b81a5d18715f190c0c92467bd9371
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This adds the following commits from the submodule:
* cezanne: Upgrade blobs to 1.0.0.5
* cezanne: Upgrade ABL to ver. 0x19036070
* cezanne: Upgrade SMU FW to 64.52.0
* cezanne: Upgrade SMU to 64.57.0
* cezanne: Update ABLs to 0x1A296070
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id7b3f5d38d34c2714548dff92b7b83fb2628e936
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58989
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SCIMAPS is the total number of SCI to GEVENT mappings. configure_scimap
returns early when the scimap is greater or equal than SCIMAPS, so for
SMITYPE_ACDC_TIMER it returned early without doing what was expected
from it to do despite that being a valid value, so fix this off-by-one.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ibaf8c5618ddbf0b8d4cd612a7f1347d8562bbfcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
EINT event mask register is used to mask EINT wakeup source.
All wakeup sources are masked by default. Since most MediaTek SoCs do
not have this design, we can't modify the kernel EINT upstream driver to
solve the issue 'Can't wake using power button (cros_ec) or touchpad'.
So we add a driver here to unmask all wakeup sources.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I84946c2c74dd233419cb94f013a42c734363baf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The NOR-Flash can be configured on SPI0 or TDM-RX GPIOs so we have to
provide an init function in SoC for the mainboard to select right
configuration.
TEST=boot to romstage
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I285ec64ace8b72a48ef1d481d366bd67cb9b0337
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add spd/lp5/memory_parts.json with an empty parts list, then run spd_gen
to generate the manifests and empty SPD.
Generated using:
util/spd_tools/bin/spd_gen spd/lp5/memory_parts.json lp5
BUG=b:204284866
TEST=None
Change-Id: I0314314130a1ccc58fb5a0416b110e7a86338fd0
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add COV=1 and the `coverage-report` target to unit test build rules
in `what-jenkins-does` so that we get code coverage data from the
coreboot and libpayload unit tests.
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: I96669c47d1a48e9ab678a4b9cb1d0c8032d727f0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The `find_resource` function will never return null (will die instead).
In cases where the existing code already accounts for null pointers, it
is better to use `probe_resource` instead, which returns a null pointer
instead of dying.
Change-Id: I329efcb42a444b097794fde4f40acf5ececaea8c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lance Zhao
The `find_resource` function will never return null (will die instead).
In cases where the existing code already accounts for null pointers, it
is better to use `probe_resource` instead, which returns a null pointer
instead of dying.
Change-Id: Ic6e28add78f686fc9ab4556eddbedf7828fba9ef
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The `find_resource` function will never return null (will die instead).
In cases where the existing code already accounts for null pointers, it
is better to use `probe_resource` instead, which returns a null pointer
instead of dying.
Change-Id: Ia9a4b62c857f7362d67aee4f9de3bb2da1838394
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The `find_resource` function will never return null (will die instead).
In cases where the existing code already accounts for null pointers, it
is better to use `probe_resource` instead, which returns a null pointer
instead of dying.
Change-Id: I2a57ea1c2f5b156afd0724829e5b1880246f351f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The `find_resource` function will never return null (will die instead).
In cases where the existing code already accounts for null pointers, it
is better to use `probe_resource` instead, which returns a null pointer
instead of dying.
Change-Id: I617fea8a09049e9a87130640835ea6c3e2faec60
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The `find_resource` function will never return null (will die instead).
In cases where the existing code already accounts for null pointers, it
is better to use `probe_resource` instead, which returns a null pointer
instead of dying.
Change-Id: I13c7ebeba2e5a896d46231b5e176e5470da97343
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This API will hide all the complexity of preloading a CBFS file. It
makes it so the callers simply specify the file to preload and CBFS
takes care of the rest. It will start a new thread to read the file into
the cbfs_cache. When the file is actually required (i.e., cbfs_load,
etc) it will wait for the preload thread to complete (if it hasn't
already) and perform verification/decompression using the preloaded
buffer. This design allows decompression/verification to happen in the
main BSP thread so that timestamps are correctly reflected.
BUG=b:179699789
TEST=Test with whole CL chain, verify VGA bios was preloaded and boot
time was reduced by 12ms.
Logs:
Preloading VGA ROM
CBFS DEBUG: _cbfs_preload(name='pci1002,1638.rom', force_ro=false)
CBFS: Found 'pci1002,1638.rom' @0x20ac40 size 0xd800 in mcache @0xcb7dd0f0
spi_dma_readat_dma: start: dest: 0x021c0000, source: 0x51cc80, size: 55296
took 0 us to acquire mutex
start_spi_dma_transaction: dest: 0x021c0000, source: 0x51cc80, remaining: 55296
...
spi_dma_readat_dma: end: dest: 0x021c0000, source: 0x51cc80, remaining: 0
...
CBFS DEBUG: _cbfs_alloc(name='pci1002,1638.rom', alloc=0x00000000(0x00000000), force_ro=false, type=-1)
CBFS: Found 'pci1002,1638.rom' @0x20ac40 size 0xd800 in mcache @0xcb7dd0f0
waiting for thread
took 0 us
CBFS DEBUG: get_preload_rdev(name='pci1002,1638.rom', force_ro=false) preload successful
In CBFS, ROM address for PCI: 03:00.0 = 0x021c0000
PCI expansion ROM, signature 0xaa55, INIT size 0xd800, data ptr 0x01b0
PCI ROM image, vendor ID 1002, device ID 1638,
PCI ROM image, Class Code 030000, Code Type 00
Copying VGA ROM Image from 0x021c0000 to 0xc0000, 0xd800 bytes
$ cbmem
...
40:device configuration 5,399,404 (8,575)
65:Option ROM initialization 5,403,474 (4,070)
66:Option ROM copy done 5,403,488 (14)
...
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I879fc1316f97417a4b82483d353abdbd02b98a31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This cleans up the warning message:
WARNING: Prefer using '"%s...", __func__' to using 'thread_run', this function's name, in a string
BUG=b:179699789
TEST=boot guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I85bacb7b2d9ebec40b6b05edc2ecf0ca1fc8ceee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Move th x86 I/O functions declarations from tests mocks to the mock
architecture io.h. This will make x86 I/O-dependent tests simpler,
because the x86_io.h from mocks will not have to be included manually.
Change-Id: Ie7f06c992be306d2523f2079bc90adf114b93946
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add LP5 support to spd_tools. Currently, only Intel Alder Lake (ADL) is
supported.
The SPDs are generated based on a combination of:
- The LPDDR5 spec JESD209-5B.
- The SPD spec SPD4.1.2.M-2 (the LPDDR3/4 spec is used since JEDEC has
not released an SPD spec for LPDDR5).
- Intel recommendations in advisory #616599.
BUG=b:201234943, b:198704251
TEST=Generate the SPD and manifests for a test part, and check that the
SPD matches Intel's expectation. More details in CB:58680.
Change-Id: Ic1e68d44f7c0ad64aa9904b7e1297d24bd5db56e
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
There are a bunch of devices in the devicetree that are disabled in
FSP-S and not used on this board. Having them around in the devicetree,
even if disabled, is not necessary and leads to a message in the log
(left over static devices...check your devicetree).
This commit cleans up devicetree.cb and removes all unused and disabled
devices.
Change-Id: I7486f9ba362c80b43b6c888a3b40a4c947218299
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58887
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
AMD platforms require the SPI contents to be 64 byte aligned in order to
use the SPI DMA controller.
BUG=b:179699789
TEST=Build guybrush and verify cbfs was invoked with -a 64
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I842c85288acd8f7ac99b127c94b1cf235e264ea2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
AMD platforms require the destination to be 64 byte aligned in order to
use the SPI DMA controller. This is enforced by the destination address
register because the first 6 bits are marked as reserved.
This change adds an option to the mem_pool so the alignment can be
configured.
BUG=b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8d77ffe4411f86c54450305320c9f52ab41a3075
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56580
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently link_speed_capability is not specified within the DXIO
descriptors sent to FSP. This value specifies the maximum speed that
a PCIe device should train up to. The only device on Monkey Island that
is not currently running at full speed is the NVME but this may not
always be the case.
BUG=b:204791296
TEST=Boot to OS and check link speed with LSPCI to verify
NVME link speed goes from 2.5 GT/s to 5 GT/s
Change-Id: Ibeac4b9e6a60567fb513e157d854399f5d12aee9
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Introduce the `smbios_dev_info` devicetree keyword to specify the
instance ID and RefDes (Reference Designation) of onboard devices.
Example syntax:
device pci 1c.0 on # PCIe Port #1
device pci 00.0 on
smbios_dev_info 6
end
end
device pci 1c.1 on # PCIe Port #2
device pci 00.0 on
smbios_dev_info 42 "PCIe-PCI Time Machine"
end
end
The `SMBIOS_TYPE41_PROVIDED_BY_DEVTREE` Kconfig option enables using
this syntax to control the generated Type 41 entries. When this option
is enabled, Type 41 entries are only autogenerated for devices with a
defined instance ID. This avoids having to keep track of which instance
IDs have been used for every device class.
Using `smbios_dev_info` when `SMBIOS_TYPE41_PROVIDED_BY_DEVTREE` is not
enabled will result in a build-time error, as the syntax is meaningless
in this case. This is done with preprocessor guards around the Type 41
members in `struct device` and the code which uses the guarded members.
Although the preprocessor usage isn't particularly elegant, adjusting
the devicetree syntax and/or grammar depending on a Kconfig option is
probably even worse.
Change-Id: Iecca9ada6ee1000674cb5dd7afd5c309d8e1a64b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
PCIe root ports #4 (00:1c.3) and #6 (00:1c.5) are currently not used on
this mainboard and are not routed either, so remove them from the
devicetree completely. PCIe root port #7 (00:1c.6) is connected and
used. Add the missing settings for L1 substates and latency reporting to
disable these features for this port as well.
Change-Id: I47e8528bea993ed527a0aecdbc93b94bbd9a7a49
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
On mc_ehl2 there are currently four of the six PCIe clocks used to drive
PCIe devices. None of the used clock output is dedicated to a special
device. Therefore do not use a port mapping of the clocks to avoid a
stopping clock once a device is missing and the matching root port is
disabled. Instead set the mapping to 'PCIE_CLK_FREE' to have a free
running clock.
In addition, use the defined constant 'PCIE_CLK_NOTUSED' instead of the
value 0xFF to disable the CLKREQ-feature and unused clocks.
Change-Id: I81419887b7f463a937917b971465245c1cb46b94
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
When the mp_init_with_smm call returns a failure, coreboot can't just
continue with the initialization and boot process due to the system
being in a bad state. Ignoring the failure here would just cause the
boot process failing elsewhere where it may not be obvious that the
failed multi-processor initialization step was the root cause of that.
I'm not 100% sure if calling do_cold_reset or calling die_with_post_code
is the better option here. Calling do_cold_reset likely here would
likely result in a boot-failure loop, so I call die_with_post_code here.
BUG=b:193809448
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifeadffb3bae749c4bbd7ad2f3f395201e67d9e28
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Disable the PM ACPI timer during PMC init, when `USE_PM_ACPI_TIMER` is
disabled. This is done to bring SKL, CNL, DNV in line with the other
platforms, in order to transition handling of the PM timer from FSP to
coreboot in the follow-up changes.
Disabling is done in `finalize` since FSP makes use of the PMtimer.
Without PM Timer emulation disabling it too early would block.
Change-Id: If85c64ba578991a1b112ceac7dd10276b58b0900
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Add new folder and basic drivers for Mediatek SoC 'MT8186'.
Difference of modules including in this patch between MT8186 and existing SoCs:
Timer:
Similar to MT8195, MT8186 uses v2 timer.
EMI/PLL/SPI:
Different from existing SoCs.
TEST=boot from SPI-NOR and show uart log on MT8186 EVB
BUG=b:200134633
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I579f79c15f4bf5e1daf6b35c70cfd00a985a0b81
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58640
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On mc_ehl1 there are three of the 6 PCIe clocks used to drive PCIe
devices. None of the used clock output is dedicated to a special device
(CLK0 drives several devices on the mainboard, CLK1 and CLK2 are
connected to a PCIe switch). Therefore do not use a port mapping of the
clocks to avoid a stopping clock once a device is missing and the
matching root port is disabled. Instead set the mapping to
'PCIE_CLK_FREE' to have a free running clock.
In addition, use the defined constant 'PCIE_CLK_NOTUSED' instead of the
value 0xFF to disable the CLKREQ-feature and unused clocks.
Change-Id: I2beea76ff8fefd79f476bef343d13495b45cdfcf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58740
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Oryx Pro 6 has the same board layout as the next model in series,
Oryx Pro 7. The primary difference between the two is the dGPU (20
series to 30 series). Convert oryp6 to a variant setup in preparation
for adding the oryp7.
Change-Id: I976750c7724d23b303d0012f2d83c21a459e5eed
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Order functionally:
* first "all" and build-$tools
* followed by clean
* followed by the architecture targets
The order was chosen this way because the architecture targets are
the mostly likely to continue to grow.
While at it, also fix the build_nasm mention (it was build-nasm)
and add build_make.
Change-Id: Id58338a512d44111b41503d4c14c08be50d51cde
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58796
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PCI_DEVICE_ID_AMD_FAM17H_LPC and PCI_DEVICE_ID_AMD_FAM17H_SMBUS redefine
the same values that are already defined by PCI_DEVICE_ID_AMD_CZ_LPC and
PCI_DEVICE_ID_AMD_CZ_SMBUS, so drop PCI_DEVICE_ID_AMD_FAM17H_LPC and
PCI_DEVICE_ID_AMD_FAM17H_SMBUS. Also add some comments to the places in
the code where the defines are used to clarify which ID is used on which
hardware generation.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id0b3d7b5a886ccc76d82ada6be4145e85fd51ede
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Enable MKBP (Matrix Keyboard Protocol) interface for all volteer family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:171365305
TEST=manual test on Volteer:
Volume Up/Down and Power buttons, Tablet Mode switch
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I2bb2e895af17fa4280113e57e2b0ca780af8840e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Boris Mittelberg <bmbm@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
EC_IN_RW signal from EC GPIO is connected to GPIO E7 of SOC. This GPIO
can be used to check EC status
trusted (LOW: in RO) or untrusted (HIGH: in RW).
Branch=none
Bug=none
Test=Issue manual recovery and confirm DUT is entering recovery mode on
ADL-M RVP.
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I20804db450ab0b3ebe19c51ba2b294a0137d81a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change adds the cbfs_cache region into the x86 memlayout. The SoC
or mainboard can decide how big the region should be by specifying
CBFS_CACHE_SIZE.
BUG=b:179699789
TEST=Build guybrush and verify cbfs_cache region wasn't added.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I268b6bc10906932ee94f795684a28cfac247a68c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Addresses in AMD fw table with EFS gen2 are relative addresses, but
PSP doesn't accept relative addresses in update_psp_bios_dir().
Check for EFS gen2 and convert them as needed.
BUG=b:194263115
TEST=build and boot on guybrush and shuboz
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I95813beba7278480e6640599fcf7445923259361
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Currently, the address size field of AT24 NVM is incorrect, and
Linux v5.10 kernel logs the message below:
at24 i2c-PRP0001:01: Bad "address-width" property: 14
The valid size of the AT24 NVM is 16 bits so modify the value from
0x0E to 0x10.
TEST=Boot brya and check the kernel log and see "Bad address-width"
error message is not shown.
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I6c1ed5334396e0ca09ea0078426a7b5039ae4e8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
In order to let the ec passing the key event like recovery and power key
to the OS, we need to include EC_ENABLE_MKBP_DEVICE to generate the MKBP
device.
BUG=b:204519353, b:204512547
BRANCH=None
TEST=pressed recovery key and power button in the OS and checked the UI
behavior.
Change-Id: Ia1d0b9b301994ad9a0f4bf28b75ab0310a1d63a0
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
PCIe root ports #5 (00:1c.4) and #6 (00:1c.5) are not used on this
mainboard and are not routed either, so remove them from the devicetree
completely. PCIe root port #7 (00:1c.6) is connected and used. Add the
missing settings for L1 substates and latency reporting to disable these
features for this port as well.
Change-Id: I06f59f0369ffcd958b5fe12bb3c646d37103811f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58568
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are a bunch of devices in the devicetree that are disabled in
FSP-S and not used on this board. Having them around in the devicetree,
even if disabled, is not necessary and leads to a message in the log
(left over static devices...check your devicetree).
This commit cleans up devicetree.cb and removes all unused and disabled
devices.
Change-Id: Ia5ffb382e3524e61b8583aca801063942fe2f247
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Add DDR5 and LPDDR5 memory type checks while calculating bus width
extension (in bits).
Additionally, update all caller functions of
smbios_bus_width_to_spd_width() to pass `MemoryType` as argument.
Update `test_smbios_bus_width_to_spd_width()` to accommodate
different memory types.
Create new macro to fix incorrect bus width reporting
on platform with DDR5 and LPDDR5 memory.
With this code changes, on DDR5 system with 2 Ch per DIMM, 32 bit
primary bus width per Ch showed the Total width as:
Handle 0x000F, DMI type 17, 40 bytes
Memory Device
Array Handle: 0x0009
Error Information Handle: Not Provided
Total Width: 80 bits
Data Width: 64 bits
Size: 16 GB
...
BUG=b:194659789
Tested=On Alder Lake DDR5 RVP, SMBIOS type 17 shows expected `Total Width`.
Change-Id: I79ec64c9d522a34cb44b3f575725571823048380
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Upstream's changes have been minimal, to the perl script that we
don't use and a constness change, so I expect no harm. Still, this
keeps us in sync with the official version.
Change-Id: I5e5a2400bc3323938da4b946930e2ec119819672
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Some older devices, like the x230 Thinkpad, do not boot with the
newer Tianocore UefiPayloadPkg build target, and cannot easily be
debugged without serial UART output. As a stopgap solution, re-add
the older (now deprecated/removed) CorebootPayloadPkg build target.
This partially reverts commit d3b49b4c,
"payloads/Tianocore: Update default build target, simplify build options"
Change-Id: I81490c277626fc69d95920868d80cb24c0763de4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Some brya0 units have HPS fitted and connected to PCH I2C2, rather than
a user-facing camera.
Because HPS uses I2C address 0x51, which may conflict with the
user-facing camera EEPROM, introduce a new fw_config bit to indicate
whether HPS is present.
BUG=b:202784200
TEST=FW_NAME=brya0 emerge-brya coreboot chromeos-bootimage
TEST=ectool cbi set 6 0x28191 4 # set bit 17 for HPS
TEST=flashrom -p internal -w image-brya0.serial.bin
Signed-off-by: Dan Callaghan <dcallagh@google.com>
Change-Id: I322548bcfccf16ba571396bc88fd6fc03c036a4e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58646
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make use of `smbios_bus_width_to_spd_width()` for filling DIMM info.
Additionally, ensures dimm_info_util.c file is getting compiled for
romstage.
TEST=dmidecode -t 17 output Total Width and Data Width as expected.
Change-Id: I7fdc19fadc576dec43e12f182fe088707e6654d9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The reason cbfs_cache was disabled on x86 was due to the lack of
.data sections in the pre-RAM stages. By using
ENV_STAGE_HAS_DATA_SECTION we enable x86 to start using the cbfs_cache.
We still need to add a cbfs_cache region into the memlayout for it to
be enabled.
BUG=b:179699789
TEST=Build guybrush and verify cbfs_cache.size == 0.
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I74434ef9250ff059e7587147b1456aeabbee33aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56577
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The PCI-SIG engineering change requirement provides the ACPI additions
for firmware latency optimization. This change adds additional ACPI DSM
function with both of FW_RESET_TIME and FW_D3HOT_TO_D0_TIME to the
USB4/TBT topology which has the same implementation on Tiger Lake in
commit I5a19118b75ed0a78b7436f2f90295c03928300d7.
BUG=b:199757442
TEST= It was validated that the first connected device waits only 50ms
instead of 100ms and all functions work on Alder Lake platform boards.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I0c8977c96de27ab0e554469eba658660975b8493
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Used H1 firmware where the last version number is 0.0.22, 0.3.22 or
less to production that will need to disable autonomous GPIO power
management and then can get H1 version by gsctool -a -f -M
BUG=b:201266532
TEST=FW_NAME=kano emerge-brya coreboot and verify it builds
without error.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: If6783e0df1404c9a353061fb564210aa0d12896e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Set the `PcieRpLtrEnable` option to enable the LTR capability on all PCH
PCIe root ports.
TEST=Verify LTR capability enabled in `DevCap2` using `lspci -vv`
Change-Id: I07ea37d178ea61d904c4f131fdea31479e899ef3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58326
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Map each PCIe clock source to the corresponding root port. Also, correct
the CLKREQ# mapping for clock sources not associated to any CLKREQ# pin.
The default `PcieClkSrcClkReq` value of 0 corresponds to CLKREQ# 0.
TEST=Check that Linux sees the same PCIe devices with this commit:
- All 5 onboard Ethernet NICs
- BMC
- Two random graphics cards in PEG0 and PEG1 slots
- M.2 M NVMe SSD
Change-Id: I0515877a36d42fb8858a0f0b3c0af1199a18d9af
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The current check for XDCI enabled uses a static device path to an
internal PCI device at a very late point in the boot flow. At this
time the devicetree has been processed and disabled devices have been
already removed. If this device (00:15.1, XDCI) is disabled in
devicetree this will trigger the message
'BUG: check_xdci_enable requests hidden 00:15.1' in the log.
This looks weird and is wrong since it is not a bug to disable this
device when it is not needed.
To avoid this look up the devicetree by a tree walk instead of using
a static value for the devicetree.
Change-Id: If193be724299c4017e7e10142fac8db9fac44383
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Correct the PCIe clock source configuration as per the schematics.
Apparently, FSP does not turn off unused PCIe clock sources when using
SPS (Server Platform Services) firmware, but it does when using CSME
firmware.
TEST=BMC and Ethernet NICs get detected when using CSME firmware.
Change-Id: Id25a34816f512510640db95251a7a792c1eebe62
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
As per MP service specification, EDK2 is allowed to specify the mode
in which a 'func' routine should be executed on APs.
`SingleThread` sets to 'true' meaning to execute the function one by
one (serially) or sets to 'false' meaning to execute the function
simultaneously.
MP service API `StartupAllAPs` was designed to pass such options as
part of function argument.
But another MP service API `StartupAllCPUs` doesn't specify any such
requirement. Running the `func` simultaneously on APs results in
a coherency issue (hang while executing `func`) due to lack of
acquiring a spin lock while accessing common data structure in
multiprocessor environment.
BUG=b:199246420
Change-Id: Ia95d11408f663212fd40daa9fd9b0881a07f1ce7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This reverts commit 0a1602217f.
EC region is required in order to provide unified coreboot image for
Chrome and Windows SKU RVP's. Also removing EC region causes a regression
for ADL-P platforms.
With this patch EC region is included back into flash map.
Change-Id: I0f7f2b5dd392b08e1978a3b3f3236eac0dab1f12
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Not all platforms need to generate power resources, but the code does
not get optimized out at build time because the devicetree gets
compiled into a linked list. As this code pulls in some heavy ACPI
dependencies that is even implemented with weak empty function it
makes sense to optimize out this code using a Kconfig constant.
This saves 1.5K in ramstage size on gigabyte/ga-945gcm-s2l.
Change-Id: I82289aa7e6e82318417f3b827b86182891dfc2a6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58657
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, the AMD SDLE stardust test fails with incorrect VDD/SOC
scale/offset value, it needs to update the two load line slope
settings for the telemetry.
AGESA sends these values to the SMU, which accepts them as units of
current. Proper calibration is determined by the AMD SDLE tool and the
Stardust test.
VDD scale: 92165 -> 73457
VDD offset: 412 -> 291
SOC scale: 30233 -> 30761
SOC offset: 457 -> 834
BUG=b:200194315
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
pass AMD SDLE/Stardust test
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: If53c173000a276a80247ccb08736280a25948939
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
EN_PWR_FP is used to enable power to the FPMCU. This frees up GPIO_32
for other uses.
This move applies to all board except:
* Guybrush
* Nipperkin board version 1
Add callbacks for variants to override fpmcu shtudown gpio table and
fpmcu disable gpio table.
BUG=b:202992077
TEST=Build and boot to OS in Guybrush and Nipperkin. Ensure fingerprint
still works.
Change-Id: I4501554da0fab0cb35684735e7d1da6f20e255eb
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
GSC_SOC_INT_L gpio is used by Google Security Chip (GSC) to interrupt
SoC when the SoC is in S0 state. Hence use GPIO_85 which is in S0 domain
and save the GPIO_3 in S5 domain for other use-cases. This move applies
to all board except:
* Guybrush
* Nipperkin board version 1
Update the GPIO configuration, device tree configuration accordingly.
BUG=b:202992077
TEST=Build and boot to OS in Guybrush and Nipperkin. Ensure that the SoC
<-> TPM communication is working fine.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I019f10f2f457ab81bcff77ce8ca609b2b40cb2ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
GPIO overrides are defined for verstage. But the overrides are neither
enabled nor applied during verstage. Enable the overrides and apply them
during verstage.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform suspend/stress, warm and
cold reboot cycling for 10 iterations each. Ensure that all the PCIe
devices are enumerated fine.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I510313bf860d8d55ec3b04a9cfdfa942373163f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Used H1 firmware where the last version number is 0.0.22, 0.3.22 or
less to production that will need to disable autonomous GPIO power
management and then can get H1 version by gsctool -a -f -M
BUG=b:200918380
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I83cc1a5d80bf23d052e83c9791ef866966a3d9b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58626
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the iGPU PCI device IDs for AMD Renoir (family 17h, model 60h) and
Lucienne (family 17h, model 68h) are already defined in pci_ids.h, also
add them to the pci_device_ids list in the common AMD graphics support
block.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1c554d21eece182ecea7b09b45b7aa8a733425d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
In-band controls work to enable/disable the WWAN module. Hence
WWAN_DISABLE_GPIO is not critical and can be marked as not connected.
BUG=b:188415287
TEST=Build and boot to OS in Guybrush. Ensure that the WWAN module is
enumerated on boot and reboot.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I7fefba3de9c749971911b21ed4712e950cef5a6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
On all upcoming variants and board versions of existing variants,
SD_AUX_RESET_L signal moves from GPIO_69 to GPIO_5. This means all
boards except:
* All board versions of Guybrush
* Nipperkin Board Version 1.
Also in Nipperkin, LCD_PRIVACY_PCH signal moves from GPIO_5 to GPIO_18.
Configure the gpios accordingly in baseboard, guybrush and nipperkin
variants accordingly. Also update the DXIO port descriptor for SD PCIe
engine with the corresponding AUX reset GPIO.
BUG=b:202992077
TEST=Build and boot to OS in Guybrush & Nipperkin. Ensure that the SD
Controller and SD Card are enumerated fine. Ensure that the enumeration
is successful after a suspend/resume cycle.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: If28810747e6b4eaae2a693a98e1adc830f80bcf6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
The baseboard enables PCIe RPs 6, 8 and 9, but kano doesn't use
these. Having them enabled will occasionally cause suspend
attempts to fail, therefore disable them in the overridetree.
BUG=b:203389490 b:192370253
TEST=FW_NAME=kano emerge-brya coreboot and verify it builds
without error.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ie2b82cff6d910c961eeb56704dcbae2bdc2a8c53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58566
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
On Guybrush, pen is stuffed and GPIO_5 is used to enable Pen power. On
Nipperkin board version 1, pen is not stuffed and instead the GPIO is
used to control LCD Privacy settings. On upcoming Nipperkin board
versions and other variants, GPIO_5 is not used. Configure GPIO_5
accordingly.
BUG=b:202992077
TEST=Build and boot to OS in Guybrush. Ensure that the configuration is
retained on existing boards.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I2aa2f16282b91f157701212ee27ddd2e89918767
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
The `SMBIOS_PROVIDED_BY_MOBO` Kconfig option is already selected through
the `SECUNET_DMI` option. So, there's no need to select both of them.
Change-Id: I784df87893043a011906af8808aff27d636c7626
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58625
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FMAP was developed with assumption about endianness of the target machine.
This broke the parsing of the structure on big endian architectures. This
patch converts the endianness of the fields where applicable.
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Change-Id: I8784ac29101531db757249496315f43e4008de4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
As of 2020-07-21 their website says "we'll stop any device produce
and won't have a date to return (if we return)."
While wishing them best of luck (and welcome them back to the list
of distributors), let's take them off the list while they don't
ship hardawre.
Change-Id: Ia110d0e25bf73c3d7db270b0c2c0e23b99fc36ef
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Selecting CPU_X86_CACHE_HELPER only added the x86_enable_cache wrapper
function around enable_cache which additionally wrote a POST code to
port 0x80 and printed a message to the console. This function was only
called during multi-processor initialization in ramstage via the init
function pointer in the CPU's device operations struct and was run on
all cores, so the message on the console was printed once per CPU core.
This patch replaces all x86_enable_cache calls by calls to enable_cache
and removes the wrapper function and the Kconfig symbol
CPU_X86_CACHE_HELPER which was used to only add this when the
corresponding CPUs used the x86_enable_cache wrapper function.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Angel Pons <th3fanbus@gmail.com>
Change-Id: I5866b6bf014821ff9e3a48052a5eaf69319b003a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58579
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since all x86 CPUs in tree have MTRR support, there is no need to guard
the DISPLAY_MTRRS option with HAVE_DISPLAY_MTRRS. Also all x86 CPUs/SoCs
have a display_mtrrs call at least somewhere in their code, so selecting
the DISPLAY_MTRRS option will always have an effect. All SoCs that don't
select RESET_VECTOR_IN_RAM have the postcar stage where it gets called.
The two AMD SoCs that select RESET_VECTOR_IN_RAM use the FSP2 driver
which contains plenty of display_mtrrs calls.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2894689ce58e7404d9d5a894f3c288bc4016ea19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The Intel Quark SoC does have a LAPIC on its x86 CPU core, so we should
select CPU_X86_LAPIC. This will additionally include the Makefile from
cpu/x86/lapic. Since none of AP_IN_SIPI_WAIT, LEGACY_SMP_INIT and
UDELAY_LAPIC gets selected, only the boot_cpu.c and lapic.c targets will
be added to the build. Since SMP isn't set, adding the boot_cpu.c target
won't change the resulting binary of a timeless build, since the only
function inside will be removed by the compiler's pre-processor in the
!SMP case. So the only thing that will change the resulting binary is
the addition of the lapic.c target. From this target only the function
cpu_get_lapic_addr will be used which overrides the weak implementation
in acpi/acpi.c. The call in arch/x86/mpspec.c can be ignored, since
GENERATE_MP_TABLE isn't selected. So this change will result in the
LAPIC address in the MADT being changed from 0 to to LAPIC_DEFAULT_BASE.
Since the documentation of the Quark SoC mentions that it has a LAPIC on
its one x86 core, this should work.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2f163bd608f0548abb0e8de90843d2a796b8ef6c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Half of the AMD PCI device ID definitions were below the ATI vendor ID,
so move those below the AMD PCI vendor ID definition. The entries are
kept in the order they were before and added before the existing AMD
device ID definitions below the AMD vendor ID definition.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I34ffdc49884737541b8653bebf023a68050375d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Initialize the pad_cfg_lock_offset field for the various gpio
pad_community structures in the adl_communities.
BUG=b:201430600
TEST='emerge-brya coreboot' and verify it compiles successfully.
Change-Id: I2cd3e43a84b0140bb2aeae5de1e299db714d419b
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update api name and comments to be more generic as spi destination
id is not DMI specific.
Update api name as soc_get_spi_psf_destination_id and comments.
And move PSF definition from pcr_ids.h as it's not pcr id.
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ie338d05649d23bddae5355dc6ce8440dfb183073
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
With using a Kconfig option to add the x86 LAPIC support code to the
build, there's no need for adding the corresponding directory to subdirs
in the CPU/SoC Makefile. Comparing which CPU/SoC Makefiles added
(cpu/)x86/mtrr and (cpu/)x86/lapic before this and the corresponding
MTRR code selection patch and having verified that all platforms
added the MTRR code on that patch shows that soc/example/min86 and
soc/intel/quark are the only platforms that don't end up selecting the
LAPIC code. So for now the default value of CPU_X86_LAPIC is chosen as y
which gets overridden to n in the Kconfig of the two SoCs mentioned
above.
Change-Id: I6f683ea7ba92c91117017ebc6ad063ec54902b0a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change is required as part of HECI Interface initialization in order
to put the host and CSE into a known good state for communication. Please
refer ME BIOS specification for more details. The change adds HECI
interface reset flow in the CSE driver. It enables coreboot to send HECI
commands before DRAM Init.
BUG=b:175516533
TEST=Run 50 cold reset cycles on Brya
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ie078beaa33c6a35ae8f5f460d4354766aa710fba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
MBP Hob is being generated by FSP after getting data from ME.
coreboot does not consume this HOB and FSP provides an option
for bootloader to skip generation of MBP HOB. This will help in
saving ~14 ms of boot time.
Here is the data from Brya P1 Board:
Before: 955 returning from FspSiliconInit 879,432 (99,156)
After: 955 returning from FspSiliconInit 1,177,513 (84,506)
BUG=b:188577893
BRANCH=None
TEST=No functional impact on Brya system and boot time is reduced
with this patch.
Change-Id: Ibb64e4d0f4ae7212defb6704b05a78e754f75cd7
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58289
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
turn off WLAN ASPM L1.1/L1.2 as a short-term w/a for WLAN AP probe failure.
BUG=b:198258604
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
AP is able to be probed by wlan module
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Ic7be523626b0ff6e4b1c66ba6af13b15061ef4cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
All x86-based CPUs and SoCs in the coreboot tree end up including the
Makefile in cpu/x86/mtrr, so include this directly in the Makefile in
cpu/x86 to add it for all x86 CPUs/SoCs. In the unlikely case that a new
x86 CPU/SoC will be added, a CPU_X86_MTRR Kconfig option that is
selected be default could be added and the new CPU/SoC without MTRR
support can override this option that then will be used in the Makefile
to guard adding the Makefile from the cpu/x86/mtrr sub-directory.
In cpu/intel all models except model 2065X and 206AX are selcted by a
socket and rely on the socket's Makefile.inc to add x86/mtrr to the
subdirs, so those models don't add x86/mtrr themselves. The Intel
Broadwell SoC selects CPU_INTEL_HASWELL and which added x86/mtrr to the
subdirs. The Intel Xeon SP SoC directory contains two sub-folders for
different versions or generations which both add x86/mtrr to the subdirs
in their Makefiles.
Change-Id: I743eaac99a85a5c712241ba48a320243c5a51f76
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch fixes regression introduced by commit bee4bb5f0
(soc/intel/common/cse: Late sending EOP msg if !HECI_DISABLE_USING_SMM)
FAFT test case fail when doing `firmware_DevMode` test.
If CSE is already hidden then accessing CSE registers would be wrong
and will receive junk, hence, return as CSE is already disabled.
BUG=b:203061531
TEST=Brya system can boot to OS with recovery mode.
Change-Id: I2046eb19716c397a066c2c41e1b027a256bd6cf9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
There are manual timeout-loops which use a fixed value and udelay().
In all cases there is a debug printk() inside this loop which, when
enabled, takes way longer than the counted microsecond delay. This
leads to the result that e.g. a 1 second delay takes nearly an eternity
if the debug messages are enabled due to the longer function execution
time.
This patch uses the stopwatch scheme for the timeout-loops which still
makes sure that the timeout period is maintained while it takes longer
function calls like printk() into account. In order to keep the minimum
delay between two register accesses on the TPM keep the udelay(1)-call.
TEST=Enable TPM debug messages on a board where the TPM hits a timeout
by failure and make sure that the debug messages occur in the log
just in the timeout period. It still works as expected if the debug
messages are disabled.
Change-Id: I8fd261c9d60a9a60509c847dbc4983bc05f41d48
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This CL adds a python test for elogtool.
It tests the basic functionality of elogtool: list, clear and add.
A future CL will include more complex tests.
BUG=b:172210863
TEST=pytest elogtool_test.py
Change-Id: If1241ad070d1c690c84f5ca61c0487ba27c2a287
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
After adding code to handle the case of missing the link/bus on the CPU
cluster device in mp_cpu_bus_init, there's no need to have the LAPIC
device in the devicetree any more.
TEST=Mandolin still boots successfully.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Icfc4fb61b373129f3bf4f4de09c38076a8f66733
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
After adding the functionality to add a bus/link on the CPU cluster
device in mp_cpu_bus_init if it is missing due to no LAPIC device being
present in the devicetree below the CPU cluster device, we can use
mp_cpu_bus_init as init function in cpu_bus_ops and implement
mp_init_cpus.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I76aebeca1b3227cfd310b6c45f506c042b35ae04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
When a chipset or mainboard devicetree doesn't have any LAPIC devices in
its CPU cluster, not only the LAPIC device, but also the link/bus
between the CPU cluster device and the LAPIC devices will be missing and
the CPU cluster's dev->link_list will be NULL. This patch handles this
case in the common code like
commit 3c0ecd57c1 (soc/intel/common/cpu:
Handle non-zero BSP APIC ID in init_cpus) and
commit ba936ce5db (soc/intel/denverton_ns:
Ensure CPU device has a valid link) already did in the common Intel SoC
and the Denverton code. With this change all CPUs and SoC that use the
common mp_cpu_bus_init as init function in the CPU cluster's device
operations struct won't require having at least one LAPIC device in the
chipset or mainboard device tree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib0d85de5cafb6390b8fbd512186899d6a815e972
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
For coreboot proper, I/O APIC programming is not really required,
except for the APIC ID field. We generally do not guard the related
set_ioapic_id() or setup_ioapic() calls with CONFIG(IOAPIC).
In practice it's something one cannot leave unselected, but maintain
the Kconfig for the time being.
Change-Id: I6e83efafcf6e81d1dfd433fab1e89024d984cc1f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The number of redirection table entries (aka interrupt vectors) inside
an I/O APIC may depend of the SKU, with the related register being of
type read/write-once. Provide support utilities to either lock or set
this registers value.
Change-Id: I8da869ba390dd821b43032e4ccbc9291c39e6bab
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Each CPU/SoC checks the return value of the mp_init_with_smm and prints
the same error message if it wasn't successful, so move this check and
printk to mp_init_with_smm. For this the original mp_init_with_smm
function gets renamed to do_mp_init_with_smm and a new mp_init_with_smm
function is created which then calls do_mp_init_with_smm, prints the
error if it didn't return CB_SUCCESS and passes the return value of
do_mp_init_with_smm to its caller.
Since no CPU/SoC code handles a mp_init_with_smm failure apart from
printing a message, also add a comment at the mp_init_with_smm call
sites that the code might want to handle a failure.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I181602723c204f3e43eb43302921adf7a88c81ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Using cb_err as return type of mp_run_on_aps, mp_run_on_all_aps,
mp_run_on_all_cpus and mp_park_aps clarifies the meaning of the
different return values. This patch also adds the types.h include that
provides the definition of the cb_err enum and checks the return value
of all 4 functions listed above against the enum values instead of
either checking if it's non-zero or less than zero to handle the error
case.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4b3f03415a041d3ec9cd0e102980e53868b004b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Use a boolean type to store the information if any mp_run_on_all_cpus
call failed. This is a preparation to change the return type of
mp_run_on_all_cpus from int to enum cb_err which will be done in a
follow-up patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic04ad3e4a781a00ee6edcd7dbd24bc7601be1384
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Using cb_err as return type clarifies the meaning of the different
return values. This patch also adds the types.h include that provides
the definition of the cb_err enum and checks the return value of
mp_init_with_smm against the enum values instead of either checking if
it's non-zero or less than zero to handle the error case.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ibcd4a9a63cc87fe176ba885ced0f00832587d492
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Some elements in the ACPI CPPC table allow static DWORDs. Instead of
using a fake register resource, use a tagged union with the two types
"register" and "DWORD" and respective macros for CPPC table entries.
Test: dumped SSDT before and after do not differ.
Change-Id: Ib853261b5c0ea87ae2424fed188f2d1872be9a06
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
WWAN_AUX_RST_L is asserted during S0i3 entry. But it needs to be
de-asserted before PCIe link training during S0i3 resume. Otherwise the
concerned gpp_bridge_2 PCIe device is not enumerated on Soi3 resume.
This change feeds in the WWAN_AUX_RST_L GPIO in the DXIO descriptor so
that SMU de-asserts this reset on S0i3 resume.
BUG=b:199780346
TEST=Build and boot to OS in Guybrush. Perform suspend/resume cycles for
500 iterations. Ensure that the PCIe devices enumerate fine.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I588c490bf3f8a7beffefc3bfd8ca5167fcbcb9a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Instead of a const port descriptor, make it configurable. This will help
to avoid adding duplicate tables for every minor configuration updates.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform suspend/resume, warm and
cold reboot cycles for 10 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: If616a08ba54fddab25e5d0d860327255dfd43cbe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58378
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using cb_err as return type clarifies the meaning of the different
return values. To not change the return types of mp_run_on_aps which is
exposed outside of this compilation unit to keep the scope of this patch
limited, the return value of run_ap_work gets translated to the int
values in mp_run_on_aps. This could also be done by a cast of the
run_ap_work return value to int, but an explicit translation of the
return values should be clearer about what it does there.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id346c8edf06229a929b4783498d8c6774f54a8b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Using cb_err as return type clarifies the meaning of the different
return values. To not change the return types of mp_init_with_smm which
is exposed outside of this compilation unit to keep the scope of this
patch limited, the return value of mp_init gets translated to the int
values in mp_init_with_smm. This could also be done by a cast of the
mp_init return value to int, but an explicit translation of the return
values should be clearer about what it does there.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4129c1db06a877c47cca87782af965b62dcbbdc2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
We now pre-populate cpu_info before jumping to the C handler. We no
longer need this parameter.
I moved the stack alignment closer to the actual invocation of the C
handler so it's easier to reason about.
BUG=b:194391185, b:179699789
TEST=Boot guybrush to OS and verify all CPUs still function
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8997683b6613b7031784cabf7039a400f0efdea1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This will reduce the number of AP init paths we need to support.
BUG=b:194391185, b:179699789
TEST=Boot guybrush to OS and see all CPUs initialized correctly
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I05beb591bd7b3a26b6c51c10d4ffd6f8621c12eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
There are two possible code sections where the cpu_info macros can be
included: .code32 and .code64
Doing a `push %eax` while in a .code64 section will result in a compiler
error. This macro manually pushes the 32-bit register onto the stack so
we can share the code between 32 and 64 bit builds.
We also can't implicitly dereference per_cpu_segment_selector because
it's a 32-bit address. Trying to do this results in the following:
E: Invalid reloc type: 11
E: Illegal use of 32bit sign extended addressing at offset 0x1b2
If we load the address first, then dereference it, we can work around
the limitation.
With these fixes, 64-bit builds can now use CPU_INFO_V2.
BUG=b:179699789
TEST=Boot qemu 64 bit build with CPU_INFO_V2 and 4 CPUs. See AP init
work as expected.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4e72a808c9583bb2d0f697cbbd9cb9c0aa0ea2dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
For reproducibility, a version string is appended to the version of the
tools used in the cross-toolchain. Currently, git is used to determine
that version string at runtime of this script. There are cases, where
it's not possible to determine that version string, e.g. when a release
tarball is used, and if so, the version string is just `v_`.
Thus, allow pre-setting the variable `CROSSGCC_VERSION`.
Change-Id: I888ccd877c93436b5e033528c43bd8667b8d2f10
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
When CONFIG_X86_AMD_INIT_SIPI was set, the second/final SIPI that
afterwards checks if all APs have checked in was skipped and if it got
so far, start_aps returned CB_SUCCESS despite not having checked if all
APs had checked in after the SIPI. This patch makes start_aps skip the
first SIPI in the CONFIG_X86_AMD_INIT_SIPI case so we use the proper
timeouts and error handling for the final and this case only SIPI and
signal the caller an error when not all APs have checked in after the
SIPI.
A timeless build for lenovo/x230 which is a mainboard that doesn't
select X86_AMD_INIT_SIPI results in identical binary, so this doesn't
change the behavior of the !X86_AMD_INIT_SIPI case.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I39438229497c5d9c44dc7e247c7b2c81252b4bdb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Support Parade ps8640 as the second source edp bridge for some trogdor
board variants/revisions.
BUG=b:194741013
BRANCH=trogdor
TEST=verified firmware screen works on lazor rev9
Change-Id: Iae5ccd8d9d33d60e4c37011ecffdd7a05af59ab2
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
In preperation to CB:58396, add the parameter `-W|--print-version`,
which allows printing the content of `CROSSGCC_VERSION`. In
combination with CB:58396, this can be used to pre-set the variable
in case of the git history is not accessible.
Change-Id: I9a205ca0ecb0ece47eb5d8fa73706478354512ff
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
For reproducibility, the buildgcc script is copied to the destination
folder of the toolchain. `CROSSGCC_COMMIT` is used as a file name
extension for the script and was introduced when `CROSSGCC_VERSION`
didn't contain the commit yet. Since this is not the case anymore,
remove it.
Change-Id: Id0a0b657eb828b2728ff787228eaa38be83d9517
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58450
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Rework Kconfig file that each variant has its own config option with
their specific selects / configuration and move common selects to
`BOARD_INTEL_ADLRVP_COMMON`, which is used as base for each
variant.
Also, move selects from Kconfig.name to Kconfig that the configuration
is at one place and not distributed over two files.
Built each variant with `BUILD_TIMELESS=1` and all generated
coreboot.rom files remain identical. Excluded the .config file by
disabling `INCLUDE_CONFIG_FILE` to make this reproducible.
Change-Id: If68c118f22579cc0a3db570119798f0f535f9804
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56221
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since during AP startup it's not guaranteed that no AP console output
will be printed between consecutive printk calls in send_sipi_to_aps,
add a new line character to all printks to make sure to have the outputs
from the APs on separate lines. For consistency also add a final new
line character to the printk call in start_aps.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3983b8a0e6b272ba5fb2a90a108d17a0c480c8b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58454
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When using `DECLARE_OPTIONAL_REGION`, it is assumed that
REGION_SIZE(name) == 0 if the region was not defined in the memlayout.
When using non-rmodule stages (i.e., bootblock, romstage, etc), this
assumption holds true, but breaks down in rmodule (i.e., ramstage)
stages.
The rmodule tool is not currently omitting undefined externals from the
relocation table. e.g.,
extern u8 _##name##_size[];
This means that when the rmodule loader runs, it will rewrite the symbol
from 0 (which is the default the linker assumed) to 0 + offset. This is
wrong since the symbol doesn't actually exist. Instead we need to omit
the relocation so it continues to keep the default value of 0.
BUG=b:179699789
TEST=Print out REGION_SIZE(cbfs_cache) in ramstage and verify it is set
to 0.
I also see the following printed by the rmodtool now:
DEBUG: Omitting relocation for undefined extern: _watchdog_tombstone_size
DEBUG: Omitting relocation for undefined extern: _watchdog_tombstone
DEBUG: Omitting relocation for undefined extern: _watchdog_tombstone
DEBUG: Omitting relocation for absolute symbol: _stack_size
DEBUG: Omitting relocation for absolute symbol: _program_size
DEBUG: Omitting relocation for absolute symbol: _cbmem_init_hooks_size
DEBUG: Omitting relocation for absolute symbol: _payload_preload_cache_size
DEBUG: Omitting relocation for absolute symbol: _payload_preload_cache
DEBUG: Omitting relocation for absolute symbol: _payload_preload_cache_size
DEBUG: Omitting relocation for absolute symbol: _payload_preload_cache
DEBUG: Omitting relocation for undefined extern: _cbfs_cache
DEBUG: Omitting relocation for undefined extern: _cbfs_cache_size
As you can see the _watchdog_tombstone will also be fixed by this CL.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib57e263fa9014da4f6854637000c1c8ad8eb351a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Instead of using two variables, one for the boolean value and one for
the path, use just one with the path. Since an empty string evalutes to
false, this simplification does not change behaviour.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I2f1171789af6815094446f107f3c634332a3427e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The SPI DMA controller can only perform transactions on a cache line
boundary. This change removes the magic number and uses the #define to
make it clear.
BUG=b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ie7b851dc2433e44a23224c3ff733fdea5fbcca0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
psp_efs.h now has embedded_firmware struct which is copied from
amdfwtool. Remove psp_ef_table from psp_verstage and use it instead to
remove duplicates.
TEST=boot on zork and guybrush
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ia362445cb7fc565b2d963f264461d833dc0338d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
ALC5682-VD/ALC5682-VS load different kernel driver by different _HID.
Update the _HID depending on the AUDIO field of fw_config.Define fw
config bit 5-7 in coreboot for codec.
BUG=b:202913837
TEST=FW_NAME=taeko emerge-brya coreboot
Change-Id: I635b173e0fe4c46d28f2c29fecee1998b29499b1
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Rework Kconfig file that each variant has its own config option with
their specific selects / configuration and move common selects to
`BOARD_INTEL_JASPERLAKE_RVP_COMMON`, which is used as base for each
variant.
Also, move selects from Kconfig.name to Kconfig that the configuration
is at one place and not distributed over two files.
Built each variant with `BUILD_TIMELESS=1` and all generated
coreboot.rom files remain identical. Excluded the .config file by
disabling `INCLUDE_CONFIG_FILE` to make this reproducible.
Change-Id: Ic7552195ed5a3ae6ab8e456d7d38d5539a052009
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Rework Kconfig file that each variant has its own config option with
their specific selects / configuration and move common selects to
`BOARD_INTEL_KBLRVP_COMMON`, which is used as base for each
variant.
Built each variant with `BUILD_TIMELESS=1` and all generated
coreboot.rom files remain identical. Excluded the .config file by
disabling `INCLUDE_CONFIG_FILE` to make this reproducible.
Change-Id: I2a9c12a15c098fcb64c006a707c94a1aed93d73a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Rework Kconfig file that each variant has its own config option with
their specific selects / configuration and move common selects to
`BOARD_INTEL_COFFEELAKE_COMMON`, which is used as base for each
variant.
Also, move selects from Kconfig.name to Kconfig so that the
configuration is at one place and not distributed over two files.
Built each variant with `BUILD_TIMELESS=1` and all generated
coreboot.rom files remain identical. Excluded the .config file by
disabling `INCLUDE_CONFIG_FILE` to make this reproducible.
Change-Id: I3b3d3cff5ea7a3f4d1c4ddd911240763e4891e06
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Thomas Heijligen <src@posteo.de>
This change adds a new command `create-cse-region` to cse_serger tool
which takes as inputs offset:size and file for different CSE
partitions and generates the entire CSE region image.
BUG=b:189177186
Change-Id: Ib087f5516e5beb6390831ef4e34b0b067d3fbc8b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change replaces `struct cse_layout_regions` with an array of
`struct region` and introduces enums for DP and BP[1-4]. This makes it
easier to loop over the different regions in following changes.
BUG=b:189177186
Change-Id: If3cced4506d26dc534047cb9c385aaa9418d8522
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
CSE RW firmware from ME_RW_A/ME_RW_B is copied over to CSE_RW region
in case of firmware update. Ensure that the size of the regions match
so that we do not have situations where ME_RW_A/B firmware grows
bigger than what CSE_RW can hold.
BUG=b:189177538
Change-Id: I374db5d490292eeb98f67dc684c2106d42779dac
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change updates the STITCH_ME_BIN path to enable support for
including CSE RW update in CBFS. CSE_RW_FILE is set to either
CONFIG_SOC_INTEL_CSE_RW_FILE or CSE_BP2_BIN depending upon the
selection of STITCH_ME_BIN config.
BUG=b:189177580
Change-Id: I0478f6b2a3342ed29c7ca21aa8e26655c58265f4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change adds support for allowing mainboards to stitch CSE
components during build time instead of adding a pre-built CSE
binary. Several Kconfig options are added to allow mainboard to
provide the file names for different CSE region components. This makes
use of the newly added cse_serger and cse_fpt tools to create
following partitions:
1. BP1 - RO
2. BP2 - RW
3. Layout
In addition to this, it accepts CSE data partition as an input using
Kconfig CSE_DATA_FILE. All these partitions are then assembled
together as per the following mainboard FMAP regions:
1. BP1(RO) : CSE_RO
2. BP2(RW) : CSE_RW
3. Layout : CSE_LAYOUT
4. Data : CSE_DATA
Finally, it generates the target $(OBJ_ME_BIN) which is used to put
together the binary in final coreboot.rom image.
Several helper functions are added to soc/intel/Makefile.inc to allow
SoCs to define which components use:
1. Decomposed files: Files decomposed from Intel release CSE binary in
FPT format.
2. Input files: Mainboard provided input files using corresponding
Kconfigs.
3. Dummy: Components that are required to have dummy entries in
BPDT header.
These helpers are added to soc/intel/Makefile.inc to ensure that the
functions are defined by the time the invocations are encountered in
SoC Makefile.inc.
BUG=b:189177580
Change-Id: I8359cd49ad256703285e55bc4319c6e9c9fccb67
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
In the following changes, CSE binary for some platforms will be
stitched at build time instead of adding a pre-built binary. This
change adds a new Kconfig `STITCH_ME_BIN` which allows mainboard to
select if it wants to stitch CSE binary instead of adding a pre-built
one. In this case, ME_BIN_PATH is not visible to user and instead
mainboard and/or SoC code is expected to provide the recipe for
stitching the CSE image.
BUG=b:189177580
Change-Id: I78ab377e110610f9ef4d86a2b6eeb4113897df85
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change moves `read_member` and `write_member` helper functions
out of cse_fpt.c and cse_serger.c into cse_helpers.c to avoid
duplication.
BUG=b:189177186,b:189167923
Change-Id: I7b646b29c9058d892bb0fc9824ef1b4340d2510c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The `acpigen_write_CST_package` and `acpigen_write_CST_package_entry`
functions don't modify the provided C-state information. So, make the
pointer parameters read-only to enforce this. Also constify arguments
where possible.
Change-Id: I9e18d82ee6c16e4435b8fad6d467e58c33194cf4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
With the recent addition of SMBIOS table 20, the cbmem area on
google/brya0 overflows and
ERROR: Increase SMBIOS size
SMBIOS tables: 2128 bytes.
is seen in the logs.
Therefore, double the size of the SMBIOS area from 2 KiB to 4 KiB to
accomodate more tables as needed. This happens during ramstage so 2k
is not a big deal at this point.
Change-Id: I43aa6a88d176e783cc9a4441b35b8d608c4101cd
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The element at offset 0x14 in the embedded_firmware struct is the
pointer to the combo PSP directory header, so rename it from comboable
to combo_psp_directory to clarify that this is not a flag, but a pointer
to a data structure. Also rename psp_entry to psp_directory since it
points to the PSP directory table.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic6149c17ae813f4dcea71c308054849a1a2e4394
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
The element at offset 0x14 in the embedded_firmware struct is the
pointer to the combo PSP directory header, so rename it from comboable
to combo_psp_directory to clarify that this is not a flag, but a pointer
to a data structure. Also rename psp_entry to psp_directory since it
points to the PSP directory table.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia70e97f10f4fa0ac63cc65a33ecdc956538482b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
This change adds a helper function `buffer_from_file_aligned_size`
that loads a file into memory buffer by creating a memory buffer of
size rounded up to the provided `size_granularity` parameter.
BUG=b:189177186,b:189167923
Change-Id: Iad3430d476abcdad850505ac50e36cd5d5deecb4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This rule was creating trouble:
* A symbol may only be declared inside or outside a choice.
The linter treats every occurence of a `config` entry as a symbol
declaration, even when it's just setting a default or adding selects.
This is not easy to fix as the symbol objects are not created first
and then added to the $symbols array when we know what kind of decla-
ration we have, but are created incrementally inside this global
list.
Change-Id: I48a17f6403470251be6b6d44bb82a8bdcbefe9f6
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56410
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The push/pop of %ebx was only added because smm_stub saves the canary
value in it. Now that we no longer use cpu_info in smm, we no longer
need to save the register.
BUG=b:179699789
TEST=Boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I554dbe016db8b1c61246c8ffc7fa252b2542ba92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Now that cpu_info() is no longer used by COOP_MULTITASKING, we no
longer need to set up cpu_info in SMM. When using CPU_INFO_V2, if
something does manage to call cpu_info() while executing in SMM mode,
the %gs segment is disabled, so it will generate an exception.
BUG=b:179699789
TEST=Boot guybrush to OS with threads enabled
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id64f32cc63082880a92dab6deb473431b2238cd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Since cpu_info() is no longer required to use threads, we no longer need
to initialize it in romstage or earlier. This code was also incomplete
since it didn't initialize the %gs segment.
BUG=b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I615b718e9f035ca68ecca9f57d7f4121db0c83b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
We only ever start and execute threads on the BSP. By explicitly
checking to see if the CPU is the BSP we can remove the dependency on
cpu_info. With this change we can in theory enable threads in all
stages.
BUG=b:194391185, b:179699789
TEST=Boot guybrush to OS and verify coop multithreading still works
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iea4622d52c36d529e100b7ea55f32c334acfdf3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58199
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Retimer FORCE_PWR GPIO is a debug GPIO, that has to be set LOW, to allow Retimer LC Domain
to toggle during a switch from DP Alt to TBT Alt modes.
Contrary to DS specifying it may be left unconfigured, hence floating, there are instances
seen during boot, where it stays HIGH (adlmrvp) or LOW (adlprvp).
Hence configure it to LOW.
Branch=none
Bug=none
Test=Boot to OS, connect TBT dock which enumerates in DP Alt,
Login, TBT dock enumerates in TBT Alt
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I0ff58823785a31c70535ad9c913c06a653884a2c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
For older CPU models where CPUID leaf 0xb is not supported, use
initial LAPIC ID from CPUID instead of LAPIC register space to
to detect if logical CPU is a hyperthreading sibling. The one
in LAPIC space is more complex to read, and might not reflect
CPU topology as it can be modified in XAPIC mode.
Change-Id: I8c458824db1ea66948126622a3e0d0604e391e4b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Remove code, which was only needed for B and C2 stepping
of P54C. The linux kernel source has commentary on X86_BUG_11AP:
* See if we have a good local APIC by checking for buggy Pentia,
* i.e. all B steppings and the C2 stepping of P54C when using their
* integrated APIC (see 11AP erratum in "Pentium Processor
* Specification Update")
Change-Id: Iec10335f603674bcef2e7494831cf11200795d38
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
All boards with DRIVERS_GENERIC_IOAPIC select it.
Presumably the related configuration of routing IRQ0 when
IOAPIC is enabled should be always done to provide i8259
legacy compatibility for payloads.
Change-Id: Ie87816271fa63bba892c8615aa5e72ee68f6ba93
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use the common ACPI code to reduce code duplication.
After this change, `PSS_MAX_ENTRIES` is honored correctly in P-state
table generation (as of commit c2540a9) and the number reduces from 10
to 7 entries.
Also, remnants of P_BLK support missed in CB:58096 will vanish.
Tested on google/fizz: no errors in dmesg, ACPI tables remain the same
(except PSS, as mentioned above).
Change-Id: I1ec804ae4006a2d9b69c0d93a658eb3b84d60b40
Tested-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44138
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Apollo Lake and Gemini Lake do not have a hardware PM ACPI timer but
only uCode PM Timer emulation. Add a Kconfig `NO_PM_ACPI_TIMER` denoting
SoCs without PM Timer and make it mutually exclusive with the Kconfig
`USE_PM_ACPI_TIMER`.
This is partly redundant to `PM_ACPI_TIMER_OPTIONAL`, which will be
dropped in the follow-up change, though.
Change-Id: Ic323bbfb7089c53a6f22724910a0ff3df8904ebd
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
uCode PM Timer emulation is only needed when the hardware PM ACPI timer
is disabled. Also, since it redirects any register accesses to uCode,
it overrides the hardware PM Timer. Thus, only enable emulation
when required.
Change-Id: I60a775bd6eb4206750f606ce8a8777d2e2dfb579
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Set `EnableTcoTimer=1` in order to keep FSP from
1) enabling ACPI Timer emulation in uCode.
2) disabling the PM ACPI Timer.
Both actions are now done in coreboot.
`EnableTcoTimer=1` makes FSP skip these steps in any possible case
including `SkipMpInit=0`, `SkipMpInit=1`, use of the MP PPI or FSP
Multiphase Init. This way full control is left to coreboot.
Change-Id: I8005daed732c031980ccc379375ff5b09df8dac1
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lance Zhao
Disable the PM ACPI timer during PMC init, when `USE_PM_ACPI_TIMER` is
disabled. This is done to bring SKL, CNL, DNV in line with the other
platforms, in order to transition handling of the PM timer from FSP to
coreboot in the follow-up changes.
For SKL and CNL, this temporarly redundantly disables the PM Timer,
since FSP does that, too. This redundancy is resolved in the follow-up.
Change-Id: I47280cd670a96c8fa5af107986496234f04e1f77
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Move disabling of PM Timer to SoC PMC code.
The original reason for placing that in `finalize` [1] was FSP hanging
due to use of the PM timer without enabling timer emulation first in
coreboot, which was added later [2].
[1] commit 6c1bf27dae (intel/skylake: disable ACPI PM Timer to enable
XTAL OSC shutdown)
[2] commit f004f66ca7 (soc/intel/skylake: Enable ACPI PM timer emulation
on all CPUs)
Change-Id: I354c3aea0c8c1f8ff3d698e0636932b7b76125f7
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Currently, only the PM1_STS mask gets passed to `acpi_fill_soc_wake`. To
be able to override the GPE0_STS mask as well, also pass that one. To
accomplish that, pointers to the variables are passed now.
Change-Id: If9f28cf054ae8b602c0587e4dd4a13a4aba810c7
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
`RTC_EN` is in the RTC well* so we can rely on the actual register
content instead of statically overriding it. Drop it from the static
wake bits mask.
* Tested on clevo/l140cu
Change-Id: Ia0ae71f0a472513233bc0fd5625faf15bf86beaf
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The PM1_EN bits WAK_STS, RTC_EN, PWRBTN_EN don't need any SoC-specific
handling. Deduplicate `acpi_fill_soc_wake` by setting these bits in
common code.
Change-Id: I06628aeb5b82b30142a383b87c82a1e22a073ef5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The `IRQ_SLOT_COUNT` value is only meaningful when generating a PIRQ
table. None of these boards do it, so specifying this value achieves
absolutely nothing. Drop it to prevent further useless copy-pasting.
Change-Id: I2d63b850c03fc1471c0eef180e8b621311b2c336
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Picasso and Cezanne define and use APU_I2C[01234]_BASE for the base
addresses of the I2C controllers, so align Stoneyridge with this. The
ACPI device names aren't changed from I2C[ABCD] to I2C[0123] for now
since this might change behavior in the OS and would also change the
resulting binary of a timeless build.
TEST=Timeless build results in identical image for Google/Treeya.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9c400c073eba5c14bd35703b717f75df89a8719d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58370
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since ACPI 5.0A it is allowed to disable the ACPI Timer, when the
according FADT flag `ACPI_FADT_PLATFORM_CLOCK` is unset.
Starting with Skylake, most platforms (except Xeon-SP) support PM Timer
emulation, so even legacy OSes and payloads should work fine with the
hardware PM Timer disabled. However, when the `TMR_STS` functionality
is required, some legacy OSes might still not work (properly).
Add a note about this to the Kconfig help.
Change-Id: I53f1814113902124779ed85da030374439570688
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lance Zhao
The FADT contains a flag `ACPI_FADT_PLATFORM_CLOCK` telling the OSPM if
a specification-compliant PM Timer is present. Currently, this flag is
set regardless of the timer being enabled or disabled.
To be specification-compliant, only set that flag, when the hardware PM
Timer is enabled. This changes behaviour of all mainboards defaulting to
USE_PM_ACPI_TIMER=n.
Note: On platforms supporting uCode PM ACPI Timer emulation, this is
required, too, because emulation does not support `TMR_STS`. Any
OS or software checking this flag and thus relying on the overflow
flag would not work (properly).
Change-Id: Id2e5d69b5515c21e6ce922dab2cb88b494c65ebe
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The writes were originally added due to being part of the initialization
sequence in the reference code, but coreboot already has those registers
cleared by the time we reach this part of the code, so we can drop these
redundant writes.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I43344460e5355664841d77daf1df3fd386e047e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
If a system doesn't use eSPI or has the eSPI interface already
configured in verstage on PSP, not calling configure_espi_with_mb_hook
from fch_pre_init makes it a bit more obvious that the eSPI interface
initialization will be skipped.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia77b83d56a5dab1bac6cfbbd92d33aa60a9e8b89
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Now that the I2C[ABCD]_BASE_ADDRESS defines aren't macros that calculate
the MMIO addresses any more, those defines can also be used in the ACPI
code.
TEST=Timeless build results in identical image for Google/Treeya.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7de2f83dc2f8061d8f1735caf10314bcddb2d3fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The I2C_BUS_ADDRESS(x) macro isn't used to iterate over the I2C
controller base addresses, so drop this and use the fixed MMIO address
for the I2C[ABCD]_BASE_ADDRESS defines instead which also allows using
those defines in the ACPI code.
TEST=Timeless build results in identical image for Google/Treeya.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Idd7484a0322dc5167cbb7fdcd9a2583f0dbed50e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
I2C_BASE_ADDRESS is the beginning of the MMIO space that contains the
I2C controllers MMIO. I2C[ABCD]_BASE_ADDRESS are the base addresses of
the 4 I2C controllers, so use I2CA_BASE_ADDRESS instead here.
TEST=Timeless build results in identical image for Google/Treeya.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie8d6a438f76cd33929f5070f9ec6b2f280f471a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Before this patch the reservation of the MMIO region of the I2C
controllers was done in the LPC controller PCI device despite the I2C
controllers already being devices in the devicetree. This patch
implements this functionality as read_resources function of the I2C
device instead. This will only reserve the memory when the I2C devices
are enabled in devicetree which is a change from the previous behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I67c853df3be2f593ecfa113ae2f74e5df7cf74e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58307
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change splits CSE metadata structure (added to CBFS) into two
separate CBFS files (me_rw.hash and me_rw.version). Since `struct
cse_rw_metadata` is now used, it is dropped completely.
This change is being made in order to prepare for the upcoming changes
to stitch CSE binary at build time. Since the binary might not be
available pre-built, it complicates the order of operations for the
addition of CSE metadata structure and declaring hash and version as
CPPFLAGS_common. Instead rules can be enabled for individual CBFS file
targets for hash and version that ensure proper ordering as well.
BUG=b:184892226
TEST=Ensured that update works correctly on brya by forcing version
mismatch. In case of version match, no update is triggered.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7c9bb165e6a64415affcd0b3331628092195fa0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The SHRM region needs to be 4 byte aligned, which make enabling
compression slightly more complicated. We need to map it to cached
memory before loading it and flushing to memory (in aligned chunks)
then remapping the address space back to device memory before
beginning execution of the SHRM region.
Also, did some cleanup in this file based on comments in CB:49392.
BUG=b:182963902
BRANCH=None
TEST=Make sure we can still boot to kernel on herobrine
Change-Id: Iaad8a8a02abe40bd01766d94ef0b61aac7671936
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Configure I2C high / low time in the device tree to ensure Touchpad
I2C CLK runs accurately between 380 kHz and 400 kHz.
Measured I2C frequency just as below after tuning:
Touch Pad CLK: 389.2 KHz
BUG=b:202787528
TEST=Build and check after tuning I2C clock is between 380 kHz and 400 kHz
Change-Id: I0f9d062fc611de0062a39849aee1174268391682
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
If the VGA BIOS file path for `VGA_BIOS_FILE` in a mainboard's Kconfig
does not exist in the coreboot tree (including submodules), drop it.
These files should be stored in the `site-local` subdirectory and the
paths specified for each board in `site-local/Kconfig`. For example:
config VGA_BIOS_FILE
default "site-local/x200_vbios.bin" if BOARD_LENOVO_X200
Note that this is just an example. There are better ways to structure
one's `site-local` subfolder. Using the `CONFIG_MAINBOARD_DIR` option
would be one of them, though variants may still need special handling.
Also, update autoport to not generate `VGA_BIOS_FILE` defaults.
Change-Id: I1b5dfba035a42d7943f270f95fb7d32b285584d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
If available, use data from MEMINFO CBMEM table and saved handles
from type 17/19 tables to generate type 20 (Memory Device Mapped
Address) SMBIOS table.
Windows 10/11 and some other OSes use this table to report the total
memory available on a given device.
Change-Id: I2574d6209d973a8e7f112eb3ef61f5d26986e47b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58271
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
variant_has_pcie_wwan helper returns true if gpp_bridge_2 PCIe engine is
enabled. On some variants, this engine is used by storage controllers.
Fix it by adding a weak override that returns no PCIe WWAN by default.
BUG=None
TEST=Build and boot to OS in Guybrush. Ensure that PCIe WWAN is
enumerated on boards where it is stuffed.
Change-Id: I07b9dd8fc5c8c3e1557f9268c1176d4a3cade1af
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
S3 is not currently functional on Guybrush. Remove support from ACPI.
BUG=b:202401767 b:181766974
TEST=Boot Guybrush
Confirm 'deep' is not in /sys/power/mem_sleep
Confirm S0ix suspend/resume still works
BRANCH=None
Change-Id: I9ed3e051f7f2e411670649ac2528a6f40229bdc6
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Files used by this test are in: tests/data/lib/lzma-test/
file.bin - files with uncompressed data
file.lzma.bin - files with LZMA-compressed data from file.bin
How to prepare compressed file:
util/cbfs-compression-tool compress file.bin /tmp/file.lzma.bin lzma
dd if=/tmp/file.lzma.bin of=file.lzma.bin skip=8 ibs=1
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Id75e0b41991382d4c391b031862106de58eacdf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
`cse_fw_update()` is currently checking whether an update is required
by comparing versions once and then again comparing versions later in
`cse_is_downgrade_instance()` to determine if the update is an upgrade
or downgrade. Additionally, if CSE RW partition is corrupt (determined
based on `cse_is_rw_bp_sign_valid()`), `cse_is_downgrade_instance()`
ends up using the corrupted version information to determine if it is
a downgrade instance.
This change reorganizes the firmware update checks to return different
status values:
1. CSE_UPDATE_NOT_REQUIRED: No update required. Versions match.
2. CSE_UPDATE_UPGRADE: Update required and it is an upgrade.
3. CSE_UPDATE_DOWNGRADE: Update required and it is a
downgrade (requires data clear).
4. CSE_UPDATE_CORRUPTED: `cse_is_rw_bp_sign_valid()` failed and hence
requires data clear.
5. CSE_UPDATE_METADATA_ERROR: Unable to read CSE metadata from CBFS.
This change also prepares the file for follow up changes which
completely drop cse_rw_metadata structure.
BUG=b:184892226
Change-Id: Iabecab8e373e65a11ba7fe1bfc125467571a0588
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58157
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently WWAN_AUX_RST_L is in S5 domain and does not get asserted on
S0i3 entry. Based on the schematics, the pull-down on that signal leads
to 10 mW power leakage on S0i3 entry. Assert the signal on S0i3 entry to
achieve some power savings and de-assert it on S0i3 exit.
BUG=b:195748540
TEST=Build and boot to OS in Guybrush. Ensure that the signal gets
asserted on S0i3 entry and de-asserted on S0i3 exit. Trigger
suspend/resume cycles and ensure that the WWAN module is enumerated
after each cycle.
Change-Id: I43c8655ee5209779748e4365db973e094cb08aca
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58275
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support to handle S0ix entry and exit notifications by adding the
corresponding _DSM functions. The function indices are chosen based on
the Modern Standby BIOS Implementation Guide 56358 Rev. 1.04. Inside
the notification functions perform any mainboard specific S0ix entry and
exit actions.
BUG=b:195748540
TEST=Build and boot to OS in Guybrush. Ensure that the notification
functions are invoked on S0ix entry and exit. Perform suspend/resume
cycles for multiple iterations.
Change-Id: I3014551f6e281d466628559453a0141a3dd6abad
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58274
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Init overridetree based on the schematics.
Refer to brya0/overridetree.cb to update the settings of the devices
including DPTF, WIFI, NAU8825 and etc.
Refer to kano/overridetree.cb to update the SSD settings (pcie4_0).
TODO: DPTF and USB positions will be further updated later.
BUG=none
TEST=Build Pass
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Change-Id: I30d26a47fe93736c63b578c9180b148ef73e8b9f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
HPD event may not be ready when configuring TCSS mux for DP,
check if any DP device is connected and wait for HPD ready before
TCSS configuration. Remove unnecessary dependency on mainboard
functions, use generic interface which provides USB-C mux
operations.
BUG=b:192947843
TEST=select ENABLE_TCSS_DISPLAY_DETECTION in Kconfig.name for
Brya. Build coreboot and update your Brya. Boot Brya with USB-C
display connected, you should find `HPD ready after %lu ms` and
`Port C%zd is configured to DP mode!` in coreboot log. Display
should show screen in developer mode or recovery mode.
Signed-off-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Change-Id: Ia7e6dd952d3183ecb76de6d4887ee573ef89bb50
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Currently override speed config is applied only for non EM100 cases.
For EM100 case, override speed board version defaults to 0 leading to
"comparison of unsigned expression >= 0 is always true" error. Fix this
error by defining the override speed config for both EM100 and non-EM100
use-cases.
BUG=None
TEST=Build Guybrush for both EM100 and non-EM100 cases.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Id8ee7b01c69c4555d6e6a7b0d5f095ea3aaf3405
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58309
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
P_BLK is legacy and superseded by ACPI _CST. Also, the implementation
for most platforms in soc/intel is broken. Thus, drop it.
For APL the IO redirection is kept since it's used as replacement for
the broken MWAIT instructions.
Change-Id: I489aa7886dd9a4c1e6c12542bc2a1feba245ec36
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add support to override SPI fast speeds based on board version from both
bootblock and verstage. Overrides apply for Guybrush only and SPI speed
is overridden from 66 MHz to 100 MHz starting board version 4. This will
help to improve the boot time on board version by ~60 ms and still allow
the old boards to boot with 66 MHz.
BUG=b:199779306
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5bf03ab8772f27aca346589e9c5662caf014d0d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add support to override SPI ROM fast speed based on board version. This
will allow boards to start at lower speeds during bringup and then
switch to higher speeds after assessing the signal integrity. Also
implement a default no-op override.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ia8ff3b3bdb53fee142527ae63aa7785945909304
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Currently all SPI speed configurations are done through EFS at build
time. There is a need to apply SPI speed overrides at run-time - eg.
based on board version after assessing the signal integrity. This
override configuration can be carried out by PSP verstage and bootblock.
Export the APIs to set and read SPI speeds from both PSP verstage and
bootblock.
BUG=None
TEST=Build and boot to OS in guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I281531e506b56173471b918c746f58d1ad97162c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
eSPI is setup in two different locations in bootblock depending on early
port80 routing configuration. Also eSPI is setup in PSP, if verified
boot starts before bootblock. Consolidate all the scenarios by
initializating eSPI very early in fch_pre_init if verified boot starts
after bootblock and eSPI is enabled.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Icfeba17dae0a964c9ca73686e29c18d965589934
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since the GPIO mux/control MMIO regions are within the ACPIMMIO region,
we need to call enable_acpimmio_decode_pm04 here first so that accessing
the GPIO registers will work.
BUG=None
TEST=Build and boot to OS in Guybrush.
Change-Id: I4bc076261c72cf999a5f2464b74cff6bf694d473
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
There is the wrong register offset printed in the debug log when the
data register is written:
'lpc_tpm: Write reg 0x18 with 0xnn' should be
'lpc_tpm: Write reg 0x24 with 0xnn' for data FIFO access.
This can be confusing when searching for issues with the help of the
TPM debug messages since the code itself is correct. Fix this error.
Change-Id: Ic28ee5a07146e804574b887ea05c62e7e88e9078
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Some poppy variants did not select a system type, which led to the
default desktop type being set. Select the best fit enclosure type
for each variant.
Alphabetize the variant-specific options for improved readability.
Change-Id: I7c23f8fa3ae1de67f7a68b8a4e9ec16c4e8044df
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Make use of the newly introduced ACPI macros for CPPC table generation
that currently exists of a bunch of confusing assignments of structs
that only get partially filled.
Test: dumped SSDT before and after do not differ.
Change-Id: I844d191b1134b98e409240ede71e2751e51e2159
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lance Zhao
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The preferred location for the SPD data on mc_ehl based boards is the
HW-Info data structure. Inside this structure there is a field of 128
bytes available for the SPD data. So in order to use it construct a
buffer in memory which is 256 bytes long (as FSP requests minimum 256
bytes for the SPD data) and where the upper 128 bytes are taken from
HW-Info holding the needed timing parameters for LPDDR4.
If there is a case where HW-Info is not accessible or where the
contained SPD data is not valid (by checking the CRC in HW-Info SPD)
fall back to fixed SPD data set in CBFS.
Change-Id: I2b6a1bde0306ba84f5214b876eaf76ca12d8f058
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
For 1 bit long bit fields an unsigned type should be used. In this case
uint32_t is used instead of a generic unsigned int for both consistency
reasons with the rest of the file and to clarify that the bits will be
packed into a 32 bit memory location.
TEST=Resulting image of a timeless build for google/guybrush results in
identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic630d1709174d90336746bc37da504437c12643c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Replace the dt option `PmTimerDisabled` with use of the Kconfig option
`USE_PM_ACPI_TIMER` for enabling/disabling the PM Timer.
A default value representing the prior devicetree value was added to the
boards system76/{lemp10,galp5,darp7}, so this change will not alter
behaviour.
Change-Id: If1811c6b98847b22272acfa35ca44f4fbca68947
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
coreboot normally owns PCIe resets for all Cezanne based systems.
However during S0i3 resume coreboot cannot intervene for S0 GPIOs
(S5 carry over fine) so we needed an alternate way to de-assert
this reset on guybrush. This change feeds in the given S0 reset
GPIO (69 in this case) so that SMU may de-assert this reset on
S0i3 resume.
BUG=b:199780346
TEST=With latest FSP verify SD device trains each of 10 cycles
Cq-Depend: chrome-internal:4157948
Change-Id: Ieee31651db30147fda84ee1aa31df7cb1c206356
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58198
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update UPD to include option for FSP to de-assert PCIe reset GPIOs as
specified in the DXIO descriptors. This change requires FSP version
1.0.4 revision 2 otherwise setting this value does affect any FSP
behavior.
BUG=b:199780346
TEST=Verify toggling this value is reflected in FSP
Cq-Depend: chrome-internal:4170351
Change-Id: I0dee05fb0a650f026c2f09581117fa7fb5f6a90a
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Document what setting the PM_ACPI_S5_LPC_PIN_MODE and
PM_ACPI_S5_LPC_PIN_MODE_SEL bits causes. The corresponding code will
eventually be factored out and moved to the Cezanne SoC code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I10e3eee5cfc1c5ba2c88b8b7e83e96e481f787e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since the LPC_LDRQ0_PD_EN gets set right after it got cleared, we can
remove the clearing of that bit. This is split off from the previous
patch to be able to use timeless build to verify that the previous patch
didn't change any behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieb300e7c7ce7e74c32ebdade0360ee4bd499b11a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
It's hard to understand what this code is doing because it uses hard
coded values, so use the register and bit defines instead.
BUG=none
TEST=Timeless build for guybrush results in identical binary.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2d74ed3b9b4984ab1e2a22c50375baf9c9589df0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The definitions of bit 9 and 10 somehow got swapped between Picasso and
Renoir/Cezanne, so put those in the Cezanne-specific header file. The
reference code writes the same values to the raw bits in both, so we
probably would still get away with putting this into the common header,
but it's better to keep the defines consistent with the documentation in
all cases.
Register and bit definitions are from the Cezanne PPR #56569 Rev 3.03
and cross-checked to be compatible with the Picasso PPR #55570 Rev 3.16.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3a033d63eeb06eed6783e4c3797ad8dea490db8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Mock architecture can be used to build libpayload using host compiler.
It can be enabled by setting ARCH_MOCK=y in the dotconfig. It sets
LITTLE_ENDIAN=y, as most machines these days use little-endian CPUs.
Libpayload will use HOSTCC as CC, HOSTLD as LD, etc. instead of tools
provided by xcompile.
Mock architecture configuration can be used by payloads for testing
purposes. Thanks to it, tests can be architecture-independent,
and can be executed without requiring compatible Kconfig options,
e.g. ARCH_ARM64=y for ARM64 machine. However, one has to provide
implementation for most architecture-specific functions present
in arch/* directories.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Ie3a6e6f6cad2f8a2e48a8e546d3b79c577653080
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This change adds src/soc/* to subdirs before src/soc/*/* to allow
Makefile in src/soc/* to provide any common helpers that will be
useful for any src/soc/*/*. This is done to primarily ensure that the
helpers are defined before being invoked by the SoC Makefile.inc. This
is utilized by Intel CSE stitching mechanism in following changes.
BUG=b:189177580
Change-Id: I91579a87016fdc2b9ca2d798b81969c21c18b4a3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Fizz's USB ACPI code is intended to allow the OS to control port
charging power, but since Fizz's ports are dumb (vs smart), it
controls power to the port itself. The end result is that active
ports become disabled when rebooting from Windows (10/11), and
power is not restored until the device is powered down (a warm
reboot is not sufficient).
Subsequent Chromebox models (eg, Puff-based variants) don't bother
with EC-controlled USB port power, so just drop it since it's
problematic and provides no benefit.
Test: boot Windows 10/11, reboot, observe active USB ports still
functional (eg, USB KB still works)
Change-Id: I2c13d49b3ce8de8b0a38512db3c57d0c8ecbf0ad
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Populate a memory_info struct with PEI and SPD data, in order to inject
the CBMEM_INFO table necessary to populate a type17 SMBIOS table.
On Broadwell, this is done by the MRC binary, but the older Sandy Bridge
MRC binary doesn't populate the pei_data struct with all the info
needed, so we have to pull it from the SPD.
Some values are hardcoded based on platform specifications.
Change-Id: I15e00a01121150b778cfa684b9147d0cac97beb8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
CB:57144 broke JUNIT_OUTPUT=y, and unit-tests were writing to stderr
instead of selected XML files, because test name used for XML file
creation contains test path. Build system did not create necessary
directiories, which CMocka required to create output files.
This commit fixes writing to XML files with JUNIT_OUTPUT=y, but had to
sacrifice path in test name, as it was causing a lot of problems
(because CMocka does not know, how to write multiple test groups to one
XML file, so it uses test group name [here __TEST_NAME__(test_group)] as
part of output filename).
Example:
Test: tests/lib/rtc-test
Output file:
`build/tests/junit-tests_lib_rtc-test(tests).xml
Change-Id: I09891aca923bf1271cafeaa09f89b6539022709c
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
1. Fix PCIe slot capabilities not being really read from an IIO root
port device. The Hot-Plug capability of IIO root port cannot be
enabled due to FSP limitation (v2.1-0.2.2.0), but the code should
reflect the true capabilities by reading the root port device's CSR.
2. Initialize the characteristics flags to 0 in the for-loop to fix the
issue of the flags values persists to the next iterations.
Tested=On OCP Delta Lake, dmidecode -t 9 shows the expected results.
For example without the fix it shows 'Hot-plug devices are supported'
but in fact it's not:
System Slot Information
Designation: SSD1_M2_Data_Drive
Type: x4 PCI Express 3 x4
Current Usage: Available
Length: Short
ID: 1
Characteristics:
3.3 V is provided
PME signal is supported
Hot-plug devices are supported
Bus Address: 0000:00:1d.0
With the fix it shows the correct result:
Handle 0x0016, DMI type 9, 19 bytes
System Slot Information
Designation: SSD1_M2_Data_Drive
Type: x4 PCI Express 3 x4
Current Usage: Available
Length: Short
ID: 1
Characteristics:
3.3 V is provided
PME signal is supported
Bus Address: 0000:00:1d.0
Change-Id: Iea437cdf3da5410b6b7a749a1be970f0948d92d9
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58100
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On this mainboard there is a legacy PCI device, which is connected to
the PCIe root port via a PCIe-2-PCI bridge. This device only supports
legacy interrupt routing. For this reason, we have to adjust the PIR8
register (0x3150) which is responsible for PCIe device 25h. The bridge
is connected to PCIe root port 7.
The following routing is required:
INTA#->PIRQC#, INTB#->PIRQD#, INTC#->PIRQA#, INTD#-> PIRQB#
TEST:
- Boot into system software
Change-Id: Id6bb8d00458c4d1e3fefd01ac3848078355868d9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This board has the RTC RX6110SA connected to the I2C2 instead of SMBus
as in mc_ehl1. Set the bus speed for I2C2 to 100 kHz, since this RTC
only supports the standard speed.
TEST:
- Console Log shows no errors for RX6110SA during I2C2 init
- Finalize device for I2C 00:32 shows correct date and time
Change-Id: I679c6397fa0d213a25eebaf8a9e0bda9941acd26
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Since this variant uses different DDR4 devices compared to mc_ehl1 in a
memory down configuration, the SPD data file must be adapted.
In a first configuration we use Micron MT53D512M32D2NP modules.
Following values were adjusted according to this board characteristic
and with help of Serial Presence Detect (SPD) for LPDDR3 and LPDDR4
SDRAM Modules JEDEC Spec and the Specification for this Micron modules
itself:
- SPD Byte 4 - only 4Gb density instead of 8Gb for mc_ehl1
- SPD Byte 5 - different Row and Column Address Bits
- SPD Byte 29/30 - 4Gb LPDDR4 needs 130ns tRFCab
- SPD Byte 31/32 - 4Gb LPDDR4 needs 60ns tRFCpb
Change-Id: Icb25f418952f0c96117140863d0d9c897d814ac5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Return the package with a value for the dptf user space service.
This is required in write tpch method for pch device under dptf
driver.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I64e1bb04a6115c7f93c84a5d6644101ac1d3d8ba
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The PCI-SIG engineering change requirement provides the ACPI additions
for firmware latency optimization. This change adds additional ACPI DSM
function with both of FW_RESET_TIME and FW_D3HOT_TO_D0_TIME to the
USB4/TBT topology. The OS is informed to reduce latency for upstream
ports while connecting USB4/TBT devices.
BUG=b:199757442
TEST=It was validated that the first connected device waits only 50ms
instead of 100ms and all functions work on Voxel board.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I5a19118b75ed0a78b7436f2f90295c03928300d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add ALC5682-VS codec support in corori.
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO field of ssfc.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:201372531, b:194436265
TEST=ALC5682-VD/ALC5682-VS audio codec can work.
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I2f3edb0b594066714b42050a411103a215e68b12
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
nipperkin has different H/W topology to guybrush that the eMMC device
is on a different GPP:
guybrush: GPP3
nipperkin: GPP2
Hence we need to enable RTD3 for nipperkin additionally which refers
to this one:
https://review.coreboot.org/c/coreboot/+/54967
BUG=b:200246826
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
run suspend test on eMMC sku
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I1dca8f9e4739514d2d024374d8686f27b25582a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
BT offload hardware design is using only i2s0 pins. Need to disable
i2s2 pins which are not used. As per the hardware spec there is an OR
operation between vgpio and physical gpio pins related to i2s2. During
BT offload configuring the i2s2 pins to its native function is causing
offload issue on proto 2 boards.
BUG=b:201736222
TEST=Verified BT offload on brya on proto 1 and proto 2.
Change-Id: Ifbc53848c6ad12e537216cac3c2871088c094f3d
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
As we checked the panel doesn't display firmware screen if we hold
GPP_D5(TOUCHSCREEN_RESET) low on bugzzy. It's because of that bugzzy
uses the built-in touch screen on the panel, the panel seems like
under reset state by the TOUCHSCREEN_RESET signal.
This change sets default GPP_D5 level to high for bugzzy.
BUG=b:None
BRANCH=dedede
TEST=built and verified bugzzy showed firmware screen
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: I53e4fc52ceb14ba23c22d3c105f65634b09029f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward Doan <edoan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This patch adds the setting of PsysPmax to 145W according to
the brya board design.
BUG=b:195615830
TEST=emerge-brya coreboot chromeos-bootimage & ensure the value is
passed to FSP by enabling FSP log & Boot into the OS
Change-Id: I996a11f76fdc0c8babe0037219f5b43e45e459dd
Signed-off-by: Ryan Lin <ryan.lin@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Instead of setting each pixel in the framebuffer, use memcpy() to clear
screen faster. As this method should be fast enough, remove the fast
path using memset().
The speed of clear_screen() on brya (x_resolution = 1920,
bytes_per_line = 7680):
- Using memset(): 15ms
- Setting each pixel: 25ms
- Using memcpy(): 14ms
Also remove set_pixel_raw() since it's now used in only one place.
BUG=none
TEST=emerge-brya libpayload
TEST=Saw developer screen on brya
BRANCH=none
Change-Id: I5f08fb50faab48d3db6b61ae022af3226914f72b
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Add function needed to generate ACPI backlight control SSDT, along with
Kconfig values for accessing the registers.
Tested by adding gfx register on system76/gaze16 and booting Windows.
Display settings has a brightness setting, and can change the brightness
level.
Change-Id: Id8b14c0b4a7a681dc6cb95778c12a006a7e31373
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
SHRM is a system hardware resource manager. It is used to manage run time
DDRSS activities. DDRSS stands for DDR subsystem.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
by trying DDR clocks which through SHRM RSI command.
Change-Id: I44484573a829eaefbd34907c6fe78d427506a762
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Now that the vb2ex_hwcrypto_* stub functions are included in vboot fwlib
(CL:2353775), we can remove the same stubs from coreboot.
BUG=none
TEST=emerge-brya coreboot
TEST=emerge-cherry coreboot
BRANCH=none
Change-Id: I62bdc647eb3e34c581cc1b8d15e7f271211e6156
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
There are 4 GPE0 STS/EN register pairs, each 32 bit wide. However, SoC
code sets a GPE0 block size of 4 byte length instead of 32 byte.
The resulting value of `x_gpe0_blk.bit_with` is wrong, too (32 bit
instead of 256 bit).
Drop the overrides and let common ACPI code set the correct values based
on `GPE0_REG_MAX`.
Change-Id: I45ee0f6678784c292ee3ed3446bf3c0f2d53b633
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
When "SpeedStep" is disabled on an Intel Atom C3538,
the maximum CPU clock speed is always 800 MHz(min CPU clock).
Оperating system cannot change the frequency.
Avoid this issue allow "Intel Speed step" technology
for processors that do not have "Intel Turbo Boost".
Signed-off-by: Dmitry Ponamorev <dponamorev@gmail.com>
Change-Id: Ia922e45c12e4239f1d59617193cdbde2a813e7d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: King Sumo <kingsumos@gmail.com>
Add API to allow AP to send the command to EC to enter DP ALT mode
and API to wait for DP HPD event.
BUG=b:192947843
TEST=select ENABLE_TCSS_DISPLAY_DETECTION in Kconfig.name. Build
coreboot and update your system. Boot the system you will find below
message in the coreboot log with or without USB-C display connected:
'HPD ready after %lu ms' or 'HPD not ready after %ldms. Abort.'.
Signed-off-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Change-Id: Id11510c1ff58579ae2cddfe5a4d69646fd84f5c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57138
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
1. Update google_chromeec_pd_get_amode() to return bitmask.
2. Update google_chromeec_wait_for_displayport() to handle the
updated return value of google_chromeec_pd_get_amode().
3. Drop google_chromeec_pd_get_amode() from ec.h and make it static
because it's not used outside of ec.c.
BUG=b:192947843
Signed-off-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Change-Id: I6020c4305e30018d4c97d862c16e8d642c951765
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add parameter `active_cable` to obtain the cable type
(active or passive) which is needed for USB-C configuration for
some SoCs (at least Intel TGL and ADL), change the function name to
google_chromeec_usb_pd_get_info() for better understanding.
BUG=b:192947843
Signed-off-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Change-Id: Ie91a3096d49d5dde75e60ab0f2f38152cef720f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
`heci_finalize` ensures to put all heci devices to D3 by setting the
D0i3 bit prior to booting to the OS.
BUG=b:200644229
TEST=Verified D0i3 bit is set for all HECI devices prior to booting
to OS.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I86d5959646522f9a2169bf13ae04d88b8f685e14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch creates a helper function in cse common code block to check
the status of any CSE `devfn`. Example: CSE, CSE_2, IDER, KT, CSE_3 and
CSE_4.
Currently cse common code is only able to read the device state of
`PCH_DEVFN_CSE` CSE device alone.
Additionally, print `slot` and 'func' number of CSE devices in case
the device is either disable or hidden.
BUG=b:200644229
TEST=Able to build and boot ADLRVP-P with this patch where the serial
message listed the CSE devices that are disabled in the device tree
as below:
HECI: CSE device 16.01 is disabled
HECI: CSE device 16.04 is disabled
HECI: CSE device 16.05 is disabled
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I208b07e89e3aa9d682837380809fbff01ea225b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch ensures to pass cse device function number as argument for
`set_cse_device_state()` to allow coreboot to perform enable/disable of
D0i3 bit for all CSE devices to put the CSE device to Idle state or
Active state.
BUG=b:200644229
TEST= Able to build and boot ADLRVP where `set_cse_device_state()` is
able to put the CSE device toidle state or active state based on `devfn`
as argument.
Change-Id: Ibe819e690c47453eaee02e435525a25b576232b5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
CPU_INFO_V2 now encapsulates the cpu_info requirements. They no longer
need to leak through to thread.c. This allows us to remove the alignment
requirement.
BUG=b:179699789
TEST=Reboot stress test guybrush 50 times.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0af91feddcbd93b7f7d0f17009034bd1868d5aef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This reverts commit 5f80e7c764.
The smm_do_relocation failure has been fixed. I also added CPU_INFO_V2
into this patch to satisfy the dependency.
BUG=b:194391185, b:179699789
TEST=reboot stress test guybrush for 50 iterations.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I134c14748711a9c9865e0cc3e3185825f85248ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
CPU_INFO_V2 changes the behavior of cpu_info(). There is now only 1
cpu_info struct per cpu. This means that we no longer need to allocate
it at the top of each threads stack.
We can now in theory remove the CONFIG_STACK_SIZE alignment on the
thread stack sizes. We can also in theory use threads in SMM if you are
feeling venturesome.
BUG=b:194391185, b:179699789
TEST=Perform reboot stress test on guybrush with COOP_MULTITASKING
enabled.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5e04d254a00db43714ec60ebed7c4aa90e23190a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
There is currently a fundamental flaw in the current cpu_info()
implementation. It assumes that current stack is CONFIG_STACK_SIZE
aligned. This assumption breaks down when performing SMM relocation.
The first step in performing SMM relocation is changing the SMBASE. This
is accomplished by installing the smmstub at 0x00038000, which is the
default SMM entry point. The stub is configured to set up a new stack
with the size of 1 KiB (CONFIG_SMM_STUB_STACK_SIZE), and an entry point
of smm_do_relocation located in RAMSTAGE RAM.
This means that when smm_do_relocation is executed, it is running in SMM
with a different sized stack. When cpu_info() gets called it will be
using CONFIG_STACK_SIZE to calculate the location of the cpu_info
struct. This results in reading random memory. Since cpu_info() has to
run in multiple environments, we can't use a compile time constant to
locate the cpu_info struct.
This CL introduces a new way of locating cpu_info. It uses a per-cpu
segment descriptor that points to a per-cpu segment that is allocated on
the stack. By using a segment descriptor to point to the per-cpu data,
we no longer need to calculate the location of the cpu_info struct. This
has the following advantages:
* Stacks no longer need to be CONFIG_STACK_SIZE aligned.
* Accessing an unconfigured segment will result in an exception. This
ensures no one can call cpu_info() from an unsupported environment.
* Segment selectors are cleared when entering SMM and restored when
leaving SMM.
* There is a 1:1 mapping between cpu and cpu_info. When using
COOP_MULTITASKING, a new cpu_info is currently allocated at the top of
each thread's stack. This no longer needs to happen.
This CL guards most of the code with CONFIG(CPU_INFO_V2). I did this so
reviewers can feel more comfortable knowing most of the CL is a no-op. I
would eventually like to remove most of the guards though.
This CL does not touch the LEGACY_SMP_INIT code path. I don't have any
way of testing it.
The %gs segment was chosen over the %fs segment because it's what the
linux kernel uses for per-cpu data in x86_64 mode.
BUG=b:194391185, b:179699789
TEST=Boot guybrush with CPU_INFO_V2 and verify BSP and APs have correct
%gs segment. Verify cpu_info looks sane. Verify booting to the OS
works correctly with COOP_MULTITASKING enabled.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I79dce9597cb784acb39a96897fb3c2f2973bfd98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Some distributions (e.g. NixOS, Debian) are actively working on getting
rid of EOL Python 2. Since `SplitFspBin.py` supports both Python 2 and
Python 3 as of upstream commit 0bc2b07, use whatever version is present
by utilizing `python`.
Change-Id: I2a657d0d4fc1899266a9574cfdfec1380828d72d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
This change adds type-c port information for USB type-c ports to cbmem.
BUG=b:149830546
TEST='emerge-volteer coreboot chromeos-bootimage', flash and boot
volteer2 to kernel, log in and check cbmem for type-c info exported to
the payload:
localhost ~ # cbmem -c | grep type-c
added type-c port0 info to cbmem: usb2:9 usb3:1 sbu:0 data:0
added type-c port1 info to cbmem: usb2:4 usb3:2 sbu:1 data:0
Change-Id: Ic56a1ad1b617e3af000664147d21165e6ea3a742
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
GPIO PM was disabled for brask to evaluate if longer interrupt pulses
are required for ADL. Since ADL requires 4us long pulses (EDS:626817),
GPIO PM can be enabled. This change drops the GPIO PM override and
re-enables dynamic GPIO PM.
TEST=Boot brask to OS, ensure no TPM errors.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0b8b66b5526d8b80775cb7588ce6b12181af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
GPIO PM was disabled for adlrvp to evaluate if longer interrupt pulses
are required for ADL. Since ADL requires 4us long pulses (EDS:626817),
GPIO PM can be enabled. This change drops the GPIO PM override and
re-enables dynamic GPIO PM.
TEST=Boot adlrvp to OS, ensure no TPM timeout errors.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0b7b66b5525d8b80775ab7578ce6b12181af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable SMBus to support DDR4 SODIMM for brask. Enable 'smbus' in
brask device tree and add SPD addressese for the two DIMMs.
Separate the Kconfig items of brya and brask. Move
HAVE_SPD_IN_CBFS and CHROMEOS_DRAM_PART_NUMBER_IN_CBI to brya
and add config SPD_CACHE_IN_FMAP to brask.
Add a new section RW_SPD_CACHE to fmd for caching SPD data.
The renamed romstage.c is used by both brya and brask and a new
function variant_get_spd_info is provided to support the different
SPD source types.
BUG=b:194055762
BRANCH=None
TEST=build pass
Change-Id: I41c57a3df127356b8c7e619c4d6144dc73aeac72
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch feeds PsysPmax setting to FSP through UPD and adds a
PsysPmax member in chip information so that we can set PsysPmax
through devicetree. The PsysPmax needs to be set correctly mapping
to maximum system power. Otherwise, system performance would be limited
due to the default PsysPmax setting in FSP is only 21W.
BUG=b:193864533, b:195615830
TEST=Set PsysPmax to an example value eg 145 in devicetree &&
put debug code in FSP to print the PsysPmax value before sending
to Pcode, ensure the setting is correctly programmed.
Change-Id: Ia07aa815f90739240f110cab984068237c02d896
Signed-off-by: Ryan Lin <ryan.lin@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Move the locally declared typec_orientation enum from chip.h to
coreboot_tables.h.
Change enum typec_orientation name to type_c_orientation for consistency
with contents of coreboot_tables.h.
Rename TYPEC_ORIENTATION_FOLLOW_CC to TYPEC_ORIENTATION_NONE.
BUG=b:149830546
TEST="emerge-volteer coreboot" and make sure it compiles successfully.
Change-Id: I24c9177be72b0c9831791aa7d1f7b1236309c9cd
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds type-c port information for USB Type-C ports to the
coreboot table. This allows depthcharge to know the usb2 and usb3
port number assignments for each available port, as well as the SBU
and data line orientation for the board.
BUG=b:149830546
TEST='emerge-volteer coreboot chromeos-bootimage' and verify it builds
successfully. Cherry-pick CL to enable this feature for volteer,
flash and boot volteer2 to kernel, log in and check cbmem for type-c
info exported to the payload:
localhost ~ # cbmem -c | grep type-c
added type-c port0 info to cbmem: usb2:9 usb3:1 sbu:0 data:0
added type-c port1 info to cbmem: usb2:4 usb3:2 sbu:1 data:0
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Change-Id: Ice732be2fa634dbf31ec620552b383c4a5b41451
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
A signed bitfield with a length of 1 bit can only have the values 0 and
-1. Assigning a 1 ends up behaving as expected, but it's not the
semantically correct thing to do there. Changing the type of the element
to an unsigned bitfield with a length of 1 would fix that, but since
this is used as a boolean value, just change it to bool type.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I230804335e7a15a8a9489859b20846988ba6c5cd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Correct OVTI2740 information for Kano:
MIPI camera CIO port, HID and Link Freq
BUG=b:200974074
TEST=Build and boot on Kano
camera driver is not probed before,
and it can now be probed properly
after this change.
Signed-off-by: Lai, Jim <jim.lai@intel.com>
Change-Id: I4612c9d42cd59cba0991b763224f77b7af33770b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Round the PM Timer emulation frequency multiplier to the closest value
to increase precision.
Test: compared hexdumps of CML binaries for the expected result:
before: 0x262E8B51, after: 0x262E8B52
Change-Id: Iafd645c248fc17943ea4be558ed7d01a301ba809
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57943
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ensures all attempts to read CSE BAR is performing PCI config
space read and returning the BAR value rather than using cached value.
This refactoring is useful to read BAR of all CSE devices rather than
just HECI 1 alone.
Additionally, change the return type of get_cse_bar() from `uintptr_t`
to `void *` to avoid typecasting while calling read32/write32 functions.
BUG=b:200644229
TEST=Able to build and boot ADLRVP where CSE is able to perform PCI
enumeration and send the EOP message at post.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Id4ecc9006d6323b7c9d7a6af1afa5cfe63d933e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
There are two different types of 282 SKU available with TDP
of 15W and 12W for Alder Lake-M SoC. This patch adds support
for these TDP values for 282 SKU as per document 643782.
BUG=None
BRANCH=None
TEST=Build FW and test on adlrvp board
Change-Id: I553b2362b7bf811e6bf02fd9d68f78c2caeb7398
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
Set PL4 value dynamically for adlrvp board based on CPU SKUs
which is detectable at runtime. These values are based on
platform design specification.
BUG=None
BRANCH=None
TEST=Build FW and test on adlrvp board
On 682:
Overriding power limits PL1 (4000, 28000) PL2 (64000, 64000) PL4 (140000)
Change-Id: I9c0c418e2548cc7f9aa647a5ad98123b33e9f9b8
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
There are currently two variants for mc_ehl where different UARTs are
used for the console. Move the Kconfig switch UART_FOR_CONSOLE to the
Kconfig of the variant and select the matching value there.
Change-Id: I7152013a0e32ff151b92932a47953705e591dc0d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58052
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a new variant of the mc_ehl board called mc_ehl2. This patch just
copies the files and renames things where needed.
Following patches will adapt the needed features for this new variant.
Change-Id: I3ec3c091017fd66fe6a09216203cdc7c9e833846
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Pushing EOP msg post FSP notify helps to save ~30ms+ boot time across
various warm reboots.
This patch ensures late sending EOP msg when function disabling of CSE
is no longer a requirement.
BUG=b:200644229
TEST=Able to save ~30ms+ of boot time
Without this code change EOP sending timestamp as below:
943:after sending EOP to ME 1,248,328(61,954))
With this code change EOP sending timestamp as below:
943:after sending EOP to ME 1,231,660 (2,754)
Change-Id: I2b78a1c07803aacfb34dce9e94b2a05a2491aabc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch ensures soc_finalize() is getting called at the entry of
BS_PAYLOAD_BOOT boot state instead of BS_PAYLOAD_LOAD, BS_ON_EXIT.
The purpose of this change is to accommodate more time to push out
sending CSE EOP messages at post.
BUG=b:200644229
TEST=coreboot serial log suggests soc_finalize() is getting called
as part of the BS_PAYLOAD_BOOT entry.
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
BS: BS_PAYLOAD_BOOT entry times (exec / console): 21 / 15 ms
Change-Id: I8632eca057255d7f4a38b64fd17c1f3d84123051
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Prior to coreboot sending EOP messages during post, it's important to
ensure that CSE is not in Idle state. In case CSE is in Dev Idle
state (which means D0I3 bit is set), reset this bit before sending
EOP command.
This patch ensures coreboot has provision to send CSE EOP messages even
after the FSP Notify phase without any delays waiting for the device
to respond or timeout.
BUG=b:200644229
TEST=Able to send CSE EOP message even after FSP Notify phase.
Attempting CSE EOP msg sending post FSP notify without this code change
causes `timeout` issue as below:
BS: BS_PAYLOAD_LOAD exit times (exec / console): 171 / 0 ms
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
HECI: Sending End-of-Post
HECI: timed out reading answer!
HECI: Failed to receive!
HECI: receive Failed
HECI: EOP send/receive fail
ERROR: Failed to send EOP to CSE, 2
cse: CSE status registers: HFSTS1: 0x90000255, HFSTS2: 0xf10516 HFSTS3:
0x20
VB2:vb2api_fail() Need recovery, reason: 0x31 / 0xc
Saving nvdata
board_reset() called!
full_reset() called!
Attempting CSE EOP msg sending post FSP notify with this code change
is `successful` as below:
BS: BS_PAYLOAD_LOAD exit times (exec / console): 170 / 0 ms
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
HECI: Sending End-of-Post
CSE: EOP requested action: continue boot
CSE EOP successful, continuing boot
Change-Id: Iae1bc52e94b08f97004424ea0c147d6da8aca6e2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
In CB:52662 when MIPI display support was added, we accidentally changed
the code flow for eDP displays such that i2c_init() will no longer be
called when display_init_required() is false. This is a problem because
on this platform, i2c_init() does not just prepare the I2C controller
for firmware use, it also loads firmware to the controller that makes it
behave like an I2C device in the first place -- a step that the kernel
cannot later do on its own if the firmware didn't already do it.
Skipping this initialization means the I2C controller becomes unusable
to the kernel.
This patch fixes the issue by making the i2c_init() unconditional again.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie4546c31d87d91113eeef7dc7a18599a87e6d6eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58026
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For Herobrine variants that include a finger print sensor, we will
need to power sequence it. We are using the same FP sensor as
trogdor, so we will follow the timings used for trogdor from
CL:2695676.
BUG=b:198474942
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_HEROBRINE -x -a -c max -B
Change-Id: Ica6eafc47cf1b95eeb8d94c6e0a8c88519665e3f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58021
Reviewed-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id c5a482ed:
2021-09-08 17:16:59 +0000 - (sign_official_build: disable gsetup for reven)
to commit id 13f601f:
13f601f vboot: boot from miniOS recovery kernels on disk b
This brings in 14 new commits.
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Change-Id: I66788ea434a6000435b97ce64107f3b5da882414
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57994
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define SSFC bit 9-11 in coreboot for codec within ec.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:193694180
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Iba91b51cbbe7adc502372c9a026867de61d8035d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The %fs and %gs segment are typically used to implement thread local
storage or cpu local storage. We don't currently use these in coreboot,
so there is no reason to map them. By setting the segment index to 0,
it disables the segment. If an instruction tries to read from one of
these segments an exception will be raised.
The end goal is to make cpu_info() use the %gs segment. This will remove
the stack alignment requirements and fix smm_do_relocation.
BUG=b:194391185, b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iaa376e562acc6bd1dfffb7a23bdec82aa474c1d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The voltage rail discharge times have been measured, so therefore
the boot time on a cold boot when the CSE must go through a global reset
and thus a trip to S5 can be optimized. Select the lowest applicable
value for each PchPmSlp UPD that can be used with these measurements.
This is programmed in the baseboard because the measured discharge times
leave (what should be) plenty of margin for variants to also not violate
any power sequencing guidelines from the PDG.
BUG=b:184799383
TEST=verified time in S5 during a global reset is ~1s instead of 4s
Change-Id: Ia373c47b3967d68ddac21707c6eb4565d9d6519e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
NVMe needs extra time to run boot process, enable power and deassert
reset for NVMe earlier in the boot flow that taeko can successfully
boot into OS with non-serial coreboot.
BUG=b:199969366 & b:200711149
TEST=Build FW and test with non-serial FW reboot 20 times pass.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I032c5b90fb2148c4075d6ead3e4161c0cc659b20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Currently, static analyzers don't recognize that hlt() doesn't return,
so they show errors like uninitialized variables assuming that it does
return. This takes care of that problem.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ia2325700b10fe1f89d749edfe5aee72b47d02f2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The current MRC binaries for Bay Trail are always ELF files. Always
adjust the position in CBFS using the ELF header regardless of file
names. Without adjusting the position, the system hangs right after
calling into MRC.
TEST: MRC position in CBFS does not change for bostentech/gbyt4.
Change-Id: I74e1246a5fac3f3649be9842ff13c2fc70f72a20
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57989
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Refactor DPTF section of code under the kracko overridetree. This makes kracko override dptf section of dedede/baseboard, because the DPTF tool's CRT, PSV and TSR3 settings are different than expected.
BUG=b:187482019
BRANCH=dedede
TEST=Built and tested on dedede system
Change-Id: Iacc543f961a7f4652ee8583920b1794f916c7ec9
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This file does not exist in the coreboot tree. One should place this
file in the `site-local` subdirectory and specify the paths by means
of `site-local/Kconfig`.
Change-Id: I86ac2a6176947f12194bec6b63bedd7db79820a0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This will help reduce duplication and make it easier to add new members
to the cpu_info struct.
BUG=b:194391185, b:179699789
TEST=Compare assembly of romstage and ramstage before and after
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I31f264f4bb8b605fa3cb3bfff0d9bf79224072aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Enable CCP DMA use in PSP verstage. This helps to reduce the boot time.
BUG=b:194990811
TEST=Build and boot to OS in Guybrush. Observed a 35 - 40 ms improvement
in the boot time.
Before CCP DMA:
508:finished loading body 898,286 (287,576)
Total Time: 2,146,182
After CCP DMA:
508:finished loading body 853,627 (240,061)
Total Time: 2,110,117
Cq-Depend: chrome-internal:4116566
Change-Id: I6e4f081622a2ec78763adf56548204efc1bccf39
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
PSP verstage can access the boot device either in Programmed I/O mode or
DMA mode. Introduce a boot device driver and use the appropriate mode
based on the SoC support.
BUG=b:194990811
TEST=Build and boot to OS in Guybrush.
Change-Id: I8ca5290156199548916852e48f4e11de7cb886fb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57563
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support to access the boot device from PSP through Crypto
Co-Processor (CCP) DMA. Implement a SVC call to use CCP DMA on SoCs
where it is supported and a stub on SoCs where it is not supported. This
provides an improved performance while accessing the boot device and
reduces the boot time by ~45 ms.
BUG=b:194990811
TEST=Build and boot to OS in guybrush. Perform cold and warm reboot
cycling for 250 iterations.
Change-Id: I02b94a842190ac4dcf45ff2d846b8665f06a9c75
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Move includes using library paths to the top and remove unnecessary
comments. Also, get rid of that unnecessary _SB scope. Use an absolute
path for the PCI0 device instead.
Change-Id: Ibb63f3ecd9cfbb6f564e0a9968c2776c25d84f79
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Move includes using library paths to the top and remove unnecessary
comments. Also, get rid of that unnecessary _SB scope. Use an absolute
path for the PCI0 device instead.
Change-Id: I7255ac1ec6c43dd4b21325ae60e117458bea956d
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Move includes using library paths to the top and remove unnecessary
comments. Also, get rid of that unnecessary _SB scope. Use an absolute
path for the PCI0 device instead.
Change-Id: I375ab879dd95d6a7a20644dc36312a1e62f58226
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Move includes using library paths to the top and remove unnecessary
comments. Also, get rid of that unnecessary _SB scope. Use an absolute
path for the PCI0 device instead.
Change-Id: I730cd3eeffff60b3b569bfb748febbdc8ca85990
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
guybrush does not have a light sensor, do not include ACPI0008
ACPI device (Light sensor that will be managed by acpi-als IIO
kernel driver).
BUG=b:200823325
TEST=Check on Guybrush360 the sensor is not presented.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Change-Id: Id1dcb3a01ee43f780e4b118d88a0351e4c543f5a
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
AMD Firmware tool allows configuring the directory table level in which
the binaries have to be added. This helps to achieve space and boot time
savings.
BUG=b:195329409
TEST=Build and boot to OS in Guybrush. Achieve a boot time savings of
~75 ms and space savings of ~600 KB per RW section.
Change-Id: Idc212b8c4f8aacfb0132983a8055f1e97af42983
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bao Zheng <fishbaozi@gmail.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
elogtool was setting the timestamp with the wrong value in the month.
This CL fixes that by incrementing the month by one. This is needed
since gmtime() returns the month value starting at 0.
TEST=pytest elogtool_test.py (see next CL in relation chain)
Change-Id: I00f89ed99b049caafba2e47feae3c068245f9021
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
When the entry delay of L0s is less than the entry delay of L1, GL9755
will enter L0s state first. When it exits from L0s state, the time of L1
entry will be reset. Therefore, the conditions for entering L1 state
cannot be met. In order to enter L1 state, L0s needs to be disabled.
BUG=b:195611000
TEST=Verify GL9755 enters L1 by observing CLKREQ# de-asserts.
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Change-Id: If121b5cb534eb32bac8992683c3f0eee8946acec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Since the binaryPI glue code is specific to a binary interface, but not
for a hardware block, move it out of the common blocks directory. This
also brings the binaryPI support in line with the FSP support which is
used on the newer generations. This also drops the
SOC_AMD_COMMON_BLOCK_PI Kconfig option and makes use of the already
existing SOC_AMD_PI Kconfig option instead.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I014e538f2772938031950475e456cc40dd05d74c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The code in soc/amd/common/block/s3 is specific to the AMD binaryPI
coreboot integration, so move the code to soc/amd/common/block/pi. This
drops the SOC_AMD_COMMON_BLOCK_S3 Kconfig option and integrates the
dependencies and selections into the SOC_AMD_COMMON_BLOCK_PI Kconfig
option. Since only selecting SOC_AMD_COMMON_BLOCK_PI but not
SOC_AMD_COMMON_BLOCK_S3 resulted in missing functions in the linking
process, we don't lose support for any working configuration by only
having one Kconfig option for both parts.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib2bd99a88d8b05216688bc45d9c4f23a007ce870
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Use the same function name as in soc/intel for this functionality. This
also brings the function name more in line with the extended version of
this function gpio_configure_pads_with_override which additionally
supports passing a GPIO override configuration.
This might cause some pain for out-of-tree boards, but at some point
this should be made more consistent, so I don't see a too strong reason
not to do this.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I88852e040f79861ce7d190bf2203f9e0ce156690
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Various fixes to gnat and the improved nds32 backend have been merged
into gcc by now, so we don't need to carry those patches anymore.
Change-Id: Icdee2a8beedd109ee1f0eef6f32f7accbf66674b
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Ensure that the order of entries in each platform manifest is consistent
every time spd_gen is run.
BUG=b:191776301
TEST=Run spd_gen for lp4x and ddr4, check that the manifests are
unchanged.
Change-Id: I7bfea65c8fc781df80a8725c0cf20c7547c857e8
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Update the new variant templates to refer to the new unified version
of spd_tools:
- Update the comments in mem_parts_used.txt
- Change the placeholder SPD in Makefile.inc to 'placeholder'
BUG=b:191776301
TEST=None
Change-Id: I03265de0d1182da81dd25a2fe6f940a0b82e5fa4
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The variant creation script creates a placeholder file called
mem_parts_used.txt, with the intent that variant owners will populate
this file with memory parts as needed. But instead, some partners have
been adding the parts in a new file called mem_list_variant.txt and
removing the placeholder file. E.g. https://review.coreboot.org/55735.
There's nothing wrong with this, but it's confusing to have two
different file names which serve the same purpose. Bulk rename all the
mem_list_variant.txt files to mem_parts_used.txt. The only time these
file names are used is as an argument to the spd_tools part_id_gen
script, so no other changes are necessary.
BUG=None
TEST=Re-run part_id_gen for all variants of
brya/volteer/dedede/guybrush/zork. Check that the only change is to the
"Generated by" comment in Makefile.inc and dram_id.generated.txt.
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Icdeee78ae5c01e97f66c759c127175b4962d5635
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The copano and collis variants have both a mem_parts_used.txt and a
mem_list_variant.txt. The mem_parts_used.txt files are empty, so delete
them.
BUG=None
TEST=None
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Ia98aad7238b0173b8d5c048d89637bc297d02283
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all zork variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for dalboz:
util/spd_tools/bin/part_id_gen \
PCO \
ddr4 \
src/mainboard/google/zork/variants/dalboz/spd \
src/mainboard/google/zork/variants/dalboz/spd/mem_parts_used.txt
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using:
abuild -p none -t google/zork -a -x --timeless
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I305a24f9345bab28ff35e317b6e7fd7efba22413
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57772
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is another gpio group, namely HVCMOS, between GPP_C and GPP_E. Add
it, so the group index calculation for GPI/SMI/NMI results in the
correct value.
Reference: Linux linux/drivers/pinctrl/intel/pinctrl-icelake.c
Change-Id: I7725191173ddc0d43bbe940cdf3b0dc2aa3e5f8d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The moonbuggy pcie topology is the same as genesis so copy from its
device tree and gpios in order to enable these devices.
BUG=b:199746414
TEST=lspci
Change-Id: I4e916a95047b9f955734f164d7578c520478f5af
Signed-off-by: Jeff Chase <jnchase@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The value of level defined in table is the default one. We now give an
extra option in config file to change this value so some FWs can be
dropped in a more optimized way.
For the non A/B recovery mode, The value could be L1, L2, Lb or Lx,
which are level 1, leve 2, level both and using default value. If it
is empty or Lx, left the level in table unchanged.
Give a redundant field [12bxBX] in regular exprssion for A/B recovery
which will be done later.
Change-Id: I0847bc3793467a2299f14d1d2d2486f3f858d7f3
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This CL uses a 16-bit value (instead of an 8-bit value) for the year.
This is needed because the function internally does a "year % 100", so
the year should not be truncated to 8-bit before applying the modulo.
This fixes a regression introduced in commit e929a75.
BUG=b:200538760
TEST=deployed coreboot. Manually verified that year is correct using
"elogtool list"
TEST=test_that -b $BOARD $DUT firmware_EventLog
Change-Id: I17578ff99af5b31b216ac53c22e53b1b70df5084
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently spd_tools treats PCO and PLK as separate platforms. This is
unnecessary since they have the same SPD requirements. Remove PLK, and
use PCO as the platform for all zork variants.
BUG=b:191776301
TEST=None
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I7eeeab53fb3e0d92c3675fb80b4747297d4257ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all guybrush variants
to use this new location. The contents of the new SPDs are identical,
only their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for guybrush:
util/spd_tools/bin/part_id_gen \
CZN \
lp4x \
src/mainboard/google/guybrush/variants/guybrush/memory \
src/mainboard/google/guybrush/variants/guybrush/memory/mem_list_variant.txt
For dewatt, the Makefile.inc was manually modified to use the new
placeholder value.
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using:
abuild -p none -t google/guybrush -a -x --timeless
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I48ca430b80b892d68dad582b1d9937a9edafa5d4
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all dedede variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for cret:
util/spd_tools/bin/part_id_gen \
JSL \
lp4x \
src/mainboard/google/dedede/variants/cret/memory \
src/mainboard/google/dedede/variants/cret/memory/mem_parts_used.txt
For cappy, the Makefile.inc was manually modified to use the new
placeholder value.
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using:
abuild -p none -t google/dedede -a -x --timeless
Change-Id: I2871ff45d6202520d4466b68a4d5bb283faf2b63
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently, trying to regenerate the galtic Makefile.inc and
dram_id.generated.txt using part_id_gen fails due to duplicate fixed IDs
in the mem_parts_used.txt file.
Remove the fixed IDs since they aren't needed. The part IDs assigned are
the same either way.
Also delete the comments from mem_parts_used.txt, since lp4x/gen_part_id
currently doesn't support comments.
BUG=b:191776301
Regenerate the Makefile.inc and dram_id.generated.txt using gen_part_id,
and check that the part IDs don't changed. Command used:
util/spd_tools/lp4x/gen_part_id \
src/soc/intel/jasperlake/spd \
src/mainboard/google/dedede/variants/galtic/memory \
src/mainboard/google/dedede/variants/galtic/memory/mem_parts_used.txt
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Ida83814b2f19b4a56eb9fde5939fa6c7874803c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all volteer variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for voema:
util/spd_tools/bin/part_id_gen \
TGL \
lp4x \
src/mainboard/google/volteer/variants/voema/memory \
src/mainboard/google/volteer/variants/voema/memory/mem_parts_used.txt
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using:
abuild -p none -t google/volteer -a -x --timeless
Change-Id: Ibd4f42fd421bfa58354b532fe7a67ee59dac5e1d
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all brya variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for anahera:
util/spd_tools/bin/part_id_gen \
ADL \
lp4x \
src/mainboard/google/brya/variants/anahera/memory \
src/mainboard/google/brya/variants/anahera/memory/mem_parts_used.txt
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using: abuild -p none -t google/brya -a -x --timeless
Change-Id: I08efe1d75438c81161d9b496af2fa30ce6f59ade
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
When a new variant is created, it needs to have a path to its SPD binary
defined. Currently, this is done by setting SPD_SOURCES to a placeholder
SPD file, which just contains zero bytes.
To remove the need for a placeholder file, automatically generate a
single-byte spd.bin in lib/Makefile.inc when SPD_SOURCES is set to the
marker value 'placeholder'.
BUG=b:191776301
TEST=Change cappy/memory/Makefile to `SPD_SOURCES = placeholder`. Build
and check that spd.bin contains a single zero byte.
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I11f8f9b7ea3bc32aa5c7a617558572a5c1c74c72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Before this patch, gpio_configure_pads_with_override called
program_gpios once for each GPIO that needed to be configured which
resulted in base_num_pads - 1 unneeded master_switch_set/
master_switch_clr sequences for the gpio_configure_pads_with_override
call. Instead implement gpio_configure_pads_with_override as the more
generic function and program_gpios as a special case of that which
passes an empty override configuration and override pad number to
gpio_configure_pads_with_override.
TEST=GPIO configuration and multiplexer register values are the same for
all GPIOs on google/guybrush right before jumping to the payload before
and after the patch.
Change-Id: Ia8e47b2a278a1887db5406c1f863ddafa6a68675
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Earlier generation platform used `HeciEnabled` chip config (set to 0)
and HECI_DISABLE_USING_SMM Kconfig to make the CSE function disable at
the end of the post. `HeciEnabled` chip config remains enabled in all
latest generation platforms hence drop HECI_DISABLE_USING_SMM Kconfig
selection from SoC Kconfig as CSE remains default enabled.
BUG=b:200644229
TEST=No functional impact during boot as CSE (B:0, D:0x16, F:0) device
is listed with `lspci`.
Change-Id: I5278e5c2e015b91bb3df3a3c73a6c659a56794b5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
The current power sequencing for the SSD does not work in a non-serial
enabled BIOS image. It appears that the FSP scans the PCIe RPs before
the SSD has time to prepare itself for PCIe, so the FSP disables the RP
and so depthcharge cannot find a boot disk.
Changing the power sequence timing to enable power in bootblock and
deassert reset in ramstage follows the SSD's power sequence and
allows it to be discovered by the FSP so the RP does not get disabled.
BUG=b:199714453
TEST=build, boot into SSD, and run reboot stress test.
Change-Id: I5e7943a6cc88bc02bcbd97a1086b2d8044d7b1c3
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
In this file bool, uint8_t and uint32_t are used, so include types.h
directly to have those types defined instead of relying to have those
included indirectly via amdblocks/gpio_banks.h.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6f4626a50219fab818e8bc5087961a731b44e71b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Loading QUP FW as per herobrine and piglin configuration
for I2C, SPI and UART.
As part of the code clean up, update the header files of the
QUP drivers with the correct path.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: Ic218c6a91ffc4484830446d707d1f3403e2dc46b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Currently, if LIB_SPD_DEPS contains an SPD file which doesn't exist, the
file is silently skipped when creating spd.bin. Instead, fail the build.
BUG=b:191776301
TEST=Build test on brya. Build fails if a non-existent file is included
in LIB_SPD_DEPS.
Change-Id: I1bdadb72e087c2ee7a88fbab2f3607bd400fa2e4
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add a 'Generated by' string to the generated Makefile.inc and
dram_id.generated.txt, showing the command used to generate the files.
BUG=b:191776301
TEST=Run part_id_gen, check that the generated files contain the string
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Ic9a7826212a732288f36f111b7bc20365a1f702d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently, one of the arguments to part_id_gen is the directory
containing the SPD files, e.g. spd/lp4x/set-0. This requires the user of
the tool to understand the spd/ directory structure, and manually look
up the set number corresponding to their platform.
Change part_id_gen to take the platform and memory technology as
arguments instead of the SPD directory, and automatically determine the
SPD directory by reading the platforms manifest file generated by
spd_gen.go.
BUG=b:191776301
TEST=Run part_id_gen and check that the generated Makefile.inc and
dram_id.generated.txt are the same as before. Example:
util/spd_tools/bin/part_id_gen \
ADL \
lp4x \
src/mainboard/google/brya/variants/kano/memory \
src/mainboard/google/brya/variants/kano/memory/mem_parts_used.txt
Change-Id: I7cd7243d76b5769e8a15daa56b8438274bdd8e96
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Currently, the maximum part ID of 15 is enforced only for manually
assigned IDs. Also enforce it for automatically assigned IDs.
BUG=b:191776301
TEST=part_id_gen fails when the number of part IDs which would be
assigned is greater than MaxMemoryId.
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I802190a13b68439ccbcdb28300ccc5fd1b38a9c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57691
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Remove the override in guybrush devicetree that configured in-band eSPI
alerts. This will result in guybrush using dedicated open-drain eSPI
alerts. Guybrush boards must be reworked to connect the eSPI alert line,
otherwise they will not boot with this change
BUG=b:198596430
TEST=Boot on reworked guybrush
BRANCH=None
Change-Id: I185eec773336fb662d9fe7f4c11991813e4d7cd6
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57778
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change replaces the device tree walks with device pointers by
adding alias for following devices:
1. FPMCU
2. WWAN
Additionally, this change drops the __weak attribute for variant_has_*
functions as there is no need for different implementations for the
variants.
Change-Id: I8af5e27f226270e6b40a50640c87de99a5a703f7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
On some dedede variants, USB port 2.3/3.3 might be connected to either
LTE device or Type-A external port depending upon FW_CONFIG. Commit
856b579 ("mb/google/dedede/var/kracko: Update LTE USB port
configuration") enabled Type-A external port by default in override
tree and updated the config dynamically for LTE USB device if
FW_CONFIG indicated support for it. This was required because sconfig
lacked the support for multiple override devices. Commit
b9c22e0 ("util/sconfig: Compare probe conditions for override device
match") fixed this behavior in sconfig and now we can add multiple
override devices using different FW_CONFIG probe statements in
override tree. Hence, this change moves the LTE USB device to override
tree for metaknight, kracko and drawcia variants.
In addition to that, drawcia needs to be update reset_gpio depending
upon board_id. Thus, alias `lte_usb2` is used in drawcia override tree
to fix the reset_gpio for older boards i.e. board_id <= 9.
Change-Id: Ie5b205594680d9c2b8543c5c99325d95620cafd2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
On sasukette, codec device might be either 10EC5682 or RTL5682
depending upon the provisioned FW_CONFIG value for
AUDIO_CODEC_SOURCE. The HID for the device was updated in ramstage.c
because sconfig lacked the support for multiple override
devices. Commit b9c22e0 ("util/sconfig: Compare probe conditions for
override device match") fixed this behavior in sconfig and now we can
add multiple override devices using different FW_CONFIG probe
statements in override tree. Hence, this change moves the codec device
to override tree and drops the special handling in ramstage.c
This change also probes for UNPROVISIONED value of FW_CONFIG for
"10EC5682" device since some devices might have shipped with
UNPROVISIONED value and using "10EC5682" device.
Change-Id: I909a29c3df0cbb7ac3c07ca7663a49ad47007232
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This CL fixes a compilation error that happens in 32-bit platforms.
This error happens because printf() was using %ld instead of %zu to
print size_t variables.
This CL fixes it.
BUG=b:200608182
TEST=emerge-kevin (ARM 32-bit)
TEST=emerge-eve (Intel 64-bit)
Change-Id: I340e108361c052601f2b126db45caf2e35ee7ace
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Currently there are two versions of gen_part_id.go, one for LP4x and one
DDR4. This change implements a unified version of this tool.
The new part_id_gen.go is almost identical to the existing
ddr4/gen_part_id.go. The new version was based on the ddr4 version and
not the lp4x version, since the ddr4 version contains extra logic to
support fixed IDs in the mem_parts_used files.
The only non-trivial change from ddr4/gen_part_id.go is to include the
full paths of SPD files in the generated Makefile.inc. E.g. instead of
SPD_SOURCES += lp4x-spd-1.hex
the full path relative to the coreboot root directory is included:
SPD_SOURCES += spd/lp4x/set-0/spd-1.hex
BUG=b:191776301
TEST=For each variant of brya/volteer/dedede/guybrush/zork, run
part_id_gen and verify that the generated Makefile.inc and
dram_id.generated.txt are identical to those currently in the src tree,
except for the modified SPD file paths in Makefile.inc.
Example:
util/spd_tools/bin/part_id_gen \
spd/lp4x/set-0 \
src/mainboard/google/brya/variants/kano/memory \
src/mainboard/google/brya/variants/kano/memory/mem_parts_used.txt
Change-Id: Ib33d09076f340f688519dae7956a2b27af090c0b
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
When a new variant is created, its SPD_SOURCES contains a placeholder
file, to avoid a build failure due to SPD_SOURCES being empty. Currently
these placeholder files live with the rest of the SPD files in soc and
mainboard directories, e.g.
src/soc/intel/alderlake/spd/placeholder.spd.hex
Add a similar placeholder SPD file to the new spd/ directory.
BUG=b:191776301
TEST=None
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Ia6d76ed512a7e44221fc93ad960790be575c44c2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the new unified version of the spd_gen tool to generate all LP4x and
DDR4 SPDs, storing them in a new spd/ directory. Storing them in a
common location allows platforms with the same SPD requirements to share
SPD files, reducing duplication compared to storing SPDs in soc/ and
mainboard/ directories.
For each memory technology there are multiple sets of SPDs. Each set
corresponds to a set of platforms with different SPD requirements, e.g.
due to different memory training code expectations. A manifest file
(platforms_manifest.generated.txt) lists the platform -> set mappings.
Commands used to generate SPDs:
cp util/spd_tools/lp4x/global_lp4x_mem_parts.json.txt \
spd/lp4x/memory_parts.json
cp util/spd_tools/ddr4/global_ddr4_mem_parts.json.txt \
spd/ddr4/memory_parts.json
util/spd_tools/bin/spd_gen spd/lp4x/memory_parts.json lp4x
util/spd_tools/bin/spd_gen spd/ddr4/memory_parts.json ddr4
BUG=b:191776301
TEST=None
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Iac82847a1a0c1f2e7271d0d3b3a7261849813a24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: I95753fa536fae8ca4bb95007419875815c1bcb06
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: I1a55df754c711b2afb8939b442019831c25cce29
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: Idfaa9a24f7b7fefa4f63ab8e3bc4ee6a0f1faedf
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: Ie86822f22aa5899a7e446398370424ca5a4ca43d
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Fix the two issues below.
SB800: sb_Before_Pci_Init
shift out of bounds src/vendorcode/amd/cimx/sb800/PCILIB.c:49:18
ubsan: unrecoverable error.
SB800: sb_Before_Pci_Init
shift out of bounds src/vendorcode/amd/cimx/sb800/PCILIB.c:66:18
ubsan: unrecoverable error.
Found by: UBSAN
Change-Id: Id42e62d35f59793bad10998f14422ab7fb4fc029
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Currently, running abuild in a fresh checkout without having built the
toolchain results in the following confusing behaviour:
1. Run abuild. It fails due to the missing coreboot toolchain, and the
error message suggests running `make crossgcc`.
2. Run `make crossgcc`. It succeeds.
3. Re-run abuild. It still fails due to a missing coreboot toolchain.
This happens because the first abuild run generates an xcompile file
which uses the system toolchain. The second abuild run doesn't
regenerate the xcompile, so it still fails due to the non-coreboot
toolchain.
To avoid this confusing behaviour, regenerate the xcompile file every
time abuild is run.
BUG=None
TEST=Perform the steps above in a clean checkout. The second abuild run
now succeeds.
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I78a7702c45cecbfe8460ec55df03741e5ced94b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This change provides helper macros for generating pointer name and
weak pointer definition for devices using alias names. This will be
helpful for developers to reference the device pointer with alias
names used in the device tree.
Change-Id: I3a5a3c7fdc2c521bac9ab3336f5a6ebecd621e04
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change uses _dev_${ALIAS_NAME} as the name for `struct device` if
the device has an alias. In addition to that, it emits
_dev_${ALIAS_NAME}_ptr which points to the device structure. This
allows developers to directly reference a particular device in the tree
using alias name without having to walk the entire path. In later CLs,
mainboards are transitioned to use this newly emitted device structure
pointers.
Change-Id: I8306d9efba8e5ca5c0bda41baac9c90ad8b73ece
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The input buffer to the buffer_to_fifo family of functions is only read,
so it can be a const pointer. (Also, remove the MIPS check in libpayload
for these functions... the MIPS architecture has been removed a while
ago.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I021069680cf691590fdacc3d51f747f12ae3df31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
SBI comes with its own memset implementation (under a slightly
different name) that gcc11 "helpfully" tries to replace with a call
to memset(). Since we don't provide a memset, the linker isn't happy,
so prevent gcc from doing that.
Change-Id: I3459a519d46a123f873306000b8b2261bd64e0c3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We never call console_init from asm, so we don't need the asmlinkage.
This allows us to remove the arch/cpu.h include since we only needed it
for the asmlinkage #define.
BUG=b:179699789
TEST=build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9a7895d4f5cba59f6b05915fa4d6c6fd6ab85773
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57568
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
NVMe needs extra time to run boot process, enable power and deassert
reset for NVMe earlier in the boot flow that primus can successfully
boot into OS with non-serial coreboot.
BUG=b:199967106
TEST=USE="project_primus" emerge-brya coreboot and verify it builds
without error.
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I9c66efe96515347502d059556052c764c1be5d09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
When the century byte was reserved, the debug_level was accidentally
converted from an enum to a hidden value. Change it back to an enum.
Fixes: f05bd8830d ("mb/system76/*: cmos.layout: Reserve century byte")
Change-Id: Id88a7aed7b2fc793fd003db5b45f3f201b1a7630
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
When using a debug build of the FSP, the FSP-M binary is larger than the
memory region we have allocated for it, so increase the size to make the
binary of the debug build fit in there. Also adjust the VERSTAGE_ADDR so
that it starts right after the the FSP-M memory region.
TEST=coreboot builds now successfully when using a debug version of the
FSP
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib64806bcf948d5ed4bcf8e1f50004091f125dc7e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Currently there are two versions of spd_tools: one for LP4x and one for
DDR4. This change is the first step in unifying these into a single
tool.
This change implements a unified version of the spd_gen tool, by
combining the functionality currently in lp4x/gen_spd.go and
ddr4/gen_spd.go. The unified version takes the memory technology as an
argument, and generates SPD files for all platforms supporting that
technology.
BUG=b:191776301
TEST=Compare the SPDs generated by the old and new versions of the tool
for all supported platforms. For reference, the test script used is
here: https://review.coreboot.org/c/coreboot/+/57511
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I7fc036996dbafbb54e075da0c3ac2ea0886a6db2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
To save the space for FW, some of the FWs are going to be defined as
LVL2 entries. To be compatible to "flattened" layout, we still drop
the LVL2 entry to level1 if there is only one level.
Change-Id: Ibe8cdd5c14225899352b02bb19aae6059d56d428
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The `CaVrefConfig` FSP-M UPD describes how the on-die Vref generators
are connected to the DRAM. With the exception of an early Skylake RVP
board (which doesn't have coreboot support), mainboards using DDR3 or
LPDDR3 memory should set `CaVrefConfig` to 0, whereas mainboards with
DDR4 should set `CaVrefConfig` to 2. MRC uses this information during
memory training, so it is important to use the correct value to avoid
any issues, such as increased power usage, system instability or even
boot failures.
However, several Skylake DDR4 mainboards don't set `CaVrefConfig` to 2.
Although they can boot successfully, it's not optimal. For boards that
set `DIMM_SPD_SIZE` to 512 (DDR4 SPD size), set `CaVrefConfig` to 2.
Change-Id: Idab77daff311584b3e3061e9bf107c2fc1b7bdf1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
vboot_reference is introducing a new field (ctx) to store the current
boot mode in crrev/c/2944250 (ctx->bootmode), which will be leveraged
in both vboot flow and elog_add_boot_reason in coreboot.
In current steps of deciding bootmode, a function vb2ex_ec_trusted
is required. This function checks gpio EC_IN_RW pin and will return
'trusted' only if EC is not in RW. Therefore, we need to implement
similar utilities in coreboot.
We will deprecate vb2ex_ec_trusted and use the flag,
VB2_CONTEXT_EC_TRUSTED, in vboot, vb2api_fw_phase1 and set that flag
in coreboot, verstage_main.
Also add a help function get_ec_is_trusted which needed to be
implemented per mainboard.
BUG=b:177196147, b:181931817
BRANCH=none
TEST=Test on trogdor if manual recovery works
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: I479c8f80e45cc524ba87db4293d19b29bdfa2192
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57048
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make neovim the default editor and create an alias for vim.
The NixOS module for neovim is currently broken. Thus, add a note to
`description.md` to switch to that later.
Change-Id: I9345a6e32f3035565e55e50579c97121b4987d83
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57393
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a Nix shell file which provides an environment for compilation of
the coreboot toolchain. The Nix shell can be used by running the
following command:
$ nix-shell --pure util/nixshell/toolchain.nix
The `--pure` parameter is optional, but it makes sure that the
environment is as minimal as possible and does not contain any unrelated
or unneeded software or configuration.
Once compiled, the coreboot toolchain can be used without loading the
shell environment.
If `--pure` is used, SSL connections won't work since the
`SSL_CERT_FILE` environment variable is not configured, which makes the
build tool unable to download the source files. Thus, let it point to
the system certificate store.
Change-Id: I341ee28c5451d2c6cb4ff22de67161d99f4ca77a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Since the PCIE training for the USB WWAN card is no longer being run,
we can initialize the GPIOs the same for all WWAN cards.
BUG=b:193036827
TEST=Boot and reboot with fibocom FM350-GL & L850GL modules
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Idc9a7cb883fc8dd6bbc6077b8ea99182f17f888b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57317
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Check to see if the PCIe slot needs to be activated for the WWAN card.
If it doesn't, leave it unused so it will be powered off and not do
the PCIe training.
BUG=b:193036827
TEST=Boot & Reboot guybrush with both PCIe & USB WWAN cards.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I79c32e4814672c03ee0821786d5be1c77fd1b410
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO field of fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:200009010
TEST=ALC5682-VD/ALC5682-VS audio codec can work
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I09c7830fff6b318cf1a1f4a44ee0a819691f7c58
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57673
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PCIe WWAN module used on brya0 requires control over 4 signals to
successfully power it on. It is desirable to do this before passing
control to the payload, because the modem requires a ~10 seconds
initialization phase before it can be used.
The corrected sequence looks like:
1) Drive device into full reset and enable power in bootblock
2) Deassert FCPO in romstage, after power rails stabilize
3) Deassert WLAN_RST#, then WLAN_PERST# in ramstage
BUG=b:187691798
Change-Id: I10f15a4dcfd86216c334fb24b4693ea250d35ee4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This GPIO is used to force the USB retimers on Type-C ports to stay in a
powered state and can be used e.g., during a firmware update to the
retimer to force power on even when no device may be connected to the
port. However, its power rail is controlled elsewhere and coreboot is
not applying a FW update, so this GPIO should be driven low instead.
BUG=b:193402306
TEST=compile
Change-Id: I976a0b8252b31aacef476d5ee4bcf6b1ef2e79de
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Adds "add" command to elogtool. This command allows adding elog events
manually. It supports event type and, optionally, event data.
If the free buffer space is < 1/4 of the total space, it shrinks the
buffer, making sure that ~1/4 of the free space is available.
BUG=b:172210863
TEST=./elogtool add 0x17 0101
./elogtool add 0x18
Repeated the same tests on buffers that needed to be shrunk.
Change-Id: Ia6fdf4f951565f842d1bff52173811b52f617f66
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add mipi panel support for wormdingler
- Add the following panel for wormdingler:
INX P110ZZD-DF0
BOE TV110C9M-LL0
- Use panel_id to distinguish which mipi panel to use.
- Setup panel orientation
BUG=b:195898400,b:198548221
BRANCH=none
TEST=emerge-strongbad coreboot
Change-Id: I8cd28e024ecbfdcd473bc39efb529eb4aca1b5d0
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Configure I2C high / low time in the device tree to ensure I2C
CLK runs accurately between 380 kHz and 400 kHz.
Measured I2C frequency just as below after tuning:
touchpad:390kHz
codec:395.8kHz
BUG=b:199481261
BRANCH=dedede
TEST=Build and check after tuning I2C clock is between 380 kHz and 400 kHz
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: Ifadc3d19eb57fe6f67504be154c30df7bc0fee71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
All variants originally had been changed to start with an arrow with
two spaces following it to line up with the platform name. A number
of recent platforms were added only using a single space. This change
updates them all to have two spaces so they line up again.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Iab9e6207fff5a7d2f6d76e5ca33eeaca721a224f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
FspMultiPhaseSiInit API was introduced with FSP 2.2 specification
onwards. EnableMultiPhaseSiliconInit is an arch UPD also introduced
as part of FSP 2.2 specification to allow calling FspMultiPhaseSiInit
API.
However, some platforms adhere to the FSP specification but
don't have arch UPD structure, for example : JSL, TGL and Xeon-SP.
Out of these platforms, TGL supports calling of FspMultiPhaseSiInit
API and considered EnableMultiPhaseSiliconInit as a platform-specific
UPD rather than an arch UPD to allow calling into FspMultiPhaseSiInit
API.
It is important to ensure that the UPD setting and the callback for
MultiPhaseInit are kept in sync, else it could result in broken
behavior e.g. a hang is seen in FSP if EnableMultiPhaseSiliconInit
UPD is set to 1 but the FspMultiPhaseSiInit API call is skipped.
This patch provides an option for users to choose to bypass calling
into MultiPhaseSiInit API and ensures the EnableMultiPhaseSiliconInit
UPD is set to its default state as `disable` so that FSP-S don't
consider MultiPhaseSiInit API is a mandatory entry point prior to
calling other FSP API entry points.
List of changes:
1. Add `FSPS_HAS_ARCH_UPD` Kconfig for SoC to select if
`FSPS_ARCH_UPD` structure is part of `FSPS_UPD` structure.
2. Drop `soc_fsp_multi_phase_init_is_enable()` from JSL and Xeon-SP
SoCs, a SoC override to callout that SoC doesn't support calling
MultiPhase Si Init is no longer required.
3. Add `FSPS_USE_MULTI_PHASE_INIT` Kconfig for SoC to specify if
SoC users want to enable `EnableMultiPhaseSiliconInit` arch UPD (using
`fsp_fill_common_arch_params()`) and execute FspMultiPhaseSiInit() API.
4. Presently selects `FSPS_USE_MULTI_PHASE_INIT` from IA TCSS common
code.
5. Add `fsp_is_multi_phase_init_enabled()` that check applicability of
MultiPhase Si Init prior calling FspMultiPhaseSiInit() API to
honor SoC users' decision.
6. Drop `arch_silicon_init_params()` from SoC as FSP driver (FSP 2.2)
would check the applicability of MultiPhase Si Init prior calling
FspMultiPhaseSiInit() API.
Additionally, selects FSPS_HAS_ARCH_UPD for Alder Lake as Alder Lake
FSPS_UPD structure has `FSPS_ARCH_UPD` structure and drops
`arch_silicon_init_params()` from SoC
`platform_fsp_silicon_init_params_cb()`.
Skip EnableMultiPhaseSiliconInit hardcoding for Tiger Lake and uses
the fsp_is_multi_phase_init_enabled() function to override
EnableMultiPhaseSiliconInit UPD prior calling MultiPhaseSiInit FSP API.
TEST=EnableMultiPhaseSiliconInit UPD is getting set or reset based on
SoC user selects FSPS_USE_MULTI_PHASE_INIT Kconfig.
Change-Id: I019fa8364605f5061d56e2d80b20e1a91857c423
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch selects SOC_INTEL_COMMON_BLOCK_TCSS from Alder Lake SoC
Kconfig and drops SOC_INTEL_COMMON_BLOCK_TCSS Kconfig selection from
specific mainboard (brya) to ensure all Alder Lake mainboards can make
use of common TCSS block.
BUG=b:187385592
TEST=Type-C pendrive/Gen-2 SSD detected as Super speed.
Change-Id: I85f6a967eb34ea760418131a9586bfdeb13c9b5d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch allows ADL-RVP mainboards to set AUX GPIO PADs based
on the board id value.
Various ADL-P and ADL-M RVPs SKUs demand different GPIO AUX programming
hence, this patch implements a helper function inside `adlrvp` mainboard
to override devicetree chip config.
Note: Different ADL-P/M SKUs (LP4/LP5/DDR4/DDR5) don't have dedicated
devicetree for overrides hence, board id is being used for unique SKU
identification.
Additionally, skip AUX GPIO PAD filling up for Windows SKUs.
TEST=Able to override AUX GPIO PADs based on ADL-P RVP board id.
Change-Id: I2f0a37c7a8bd69af715551df2a93e6eed89e954a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This function is "extracted" from cmd_clear().
This new function will be called from cmd_add(), and new command that
will be added in a future CL (see CL chain).
Additional minor fixes:
- calls usage() if no valid commands are passed.
- Slightly improves usage() output. Needed for cmd_clear()
BUG=b:172210863
TEST=elogtool clear
Change-Id: I0d8ecc893675758d7f90845282a588d367b55567
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Commit 2eb100dd12 added PMC LPM requirements to the the PEP ACPI
objects, but it was not made clear that one of the pointer arguments to
the mentioned function is not supposed to be NULL and Coverity
complained. Make the intention clear by instead asserting that `info`
cannot be NULL.
Fixes: Coverity CID 1462119
Change-Id: I9e8862a100d92f4a7ed1826d3970a5110b47f4c4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This change uses a static 8-bit counter in
`acpi_device_add_power_res()` to generate the name of power resource
object rather using a default name "PRIC". This makes it easier to
identify which power resource Linux kernel logs are referring to. If
more than 256 power resources are used in the system, then the counter
will wrap around to 0. However, 256 seems to be a large enough number
for the power resource count.
TEST=Verified that Power Resources are named as expected:
```
dmesg | grep ACPI | grep PR
[ 0.550921] ACPI: Power Resource [PR00] (on)
[ 0.869960] ACPI: Power Resource [PR01] (on)
[ 1.013973] ACPI: Power Resource [PR02] (on)
```
No new ACPI errors are seen in dmesg on brya.
Change-Id: Ia18f7177b03821ce0f8c989ae5d258f2f83517a5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
copy existing QUP driver from /soc/qualcomm/sc7180 to common folder.
This QUP common driver provide QUP configurations, GPI and SE
firmware loading and initializations.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I95a0fcf97b3b3a6ed26e62b3084feb4a2369cdc9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
SPI NOR size should match with coreboot ROM size. On QCOM Piglin board SPI
NOR size is 64MB and the default coreboot ROM size is 8MB. So, update the
coreboot ROM size to match with SPI NOR size.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board and checked
basic boot up.
Change-Id: I78f3f402b383bbad303f26c31d3d973c5f20d172
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Buggzy's panel is oriented with its "right" side facing upwards, therefore
the firmware screens in depthcharge were incorrectly rotated. This patch
changes the orientation of the framebuffer provided by the FSP.
BUG=b:194967458
BRANCH=dedede
Change-Id: I4a5fbfcfc1c362da1bddd23c7d132416db3691c9
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
When the FSP driver fills out framebuffer information for the coreboot
tables, it assumes the orientation is always normal. This patch provides
a field for a mainboard to override the panel orientation from the
default (LB_FB_ORIENTATION_NORMAL). Later patches will have the FSP
driver use this value when filling out framebuffer information.
BUG=b:194967458
BRANCH=dedede
Change-Id: I559b3d6a076112a1c020ce5e296430d7ccba9ee4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Updating from commit id 4423276b:
2021-08-31 17:41:34 +0000 - (crossystem: add a hwid override mechanism from chromeos-config)
to commit id c5a482ed:
2021-09-08 17:16:59 +0000 - (sign_official_build: disable gsetup for reven)
This brings in 10 new commits.
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: I67d4bfa182eae98bb23ae487f117c991502b66ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Currently, check_boot_mode is called after vb2api_fw_phase1, which
makes verstage_main exit before reaching check_boot_mode if recovery
mode is manually requested. Thus, recovery mode isn't able to test
whether VB2_CONTEXT_EC_TRUSTED is set or not.
This patch makes verstage_main call check_boot_mode before
vb2api_fw_phase1 to fix the issue.
BUG=b:180927027, b:187871195
BRANCH=none
TEST=build
Change-Id: If8524d1513b13fd79320a116a83f6729a820f61f
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
CB:57324 moved panel orientation from panel_serializable_data to the
responsibility of the mainboard, but in parallel to that patch we landed
support for some new panels on the Trogdor mainboard that should be
pointing LEFT_UP. This patch fixes up the panel orientation for those.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I416b6c8804a88b36f723c4690ed78aff928a0f8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
There's dead links, CorebootPayloadPkg was replaced by UEFIPayloadPkg,
the development procedures are severely out-of-date, the only FSP 1.1
platform is Braswell (which is no longer actively developed), and the
pages don't appear in doc.coreboot.org (which uses Sphinx to generate
HTML pages from .md files). Oh, and it doesn't seem to have a license
associated to it.
Get rid of outdated documentation.
Change-Id: If359f554e85d32cdb65c3d928b5155db30bc40a5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
https://tech-docs.system76.com/models/lemp10/README.html
Tested with TianoCore (UefiPayloadPkg).
Working:
- PS/2 keyboard, touchpad
- DIMM slot and onboard RAM
- Both M.2 NVMe SSDs
- MicroSD card reader
- All USB ports
- USB-PD
- Webcam
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- HDMI output
- DP over USB-C output
- Internal microphone
- Internal speakers
- Combined 3.5mm headphone/microphone jack
- S0ix suspend*
- Booting to Pop!_OS Linux 21.04 and Windows 10
- Flashing with flashrom
Not working:
- S0ix when a device is attached to the TBT port
Change-Id: I15f7a3b6e9af07fcfde9a71d3f4a84ed625159b7
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fixes:
27c51a0 ("Revert "soc/intel/broadwell/pch: Replace ACPI device NVS"")
which reverted the removal of device NVS, but was not boot tested on any
Broadwell Chromebooks. It was recently discovered that the DNVS
object was not being loaded, due to a weak function setting the size
as zero not being defined for the platform/soc. Add the missing
overloaded function and required headers.
Test: build/boot google/auron variants LULU ans SAMUS, verify
touchpad functional and no ACPI errors in kernel boot log.
Change-Id: Icd317d117dbb068bb6da80fe56c06c0267c7b2ae
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
1. The video output now works correctly with Intel IGD (tested with
TianoCore, edk2-stable201903-3392-gf7fe27d686).
2. The kempld EC driver now supports GPIO configuration since
commit 9941e5a5e6 (ec/kontron/kempld: Add minimal GPIO driver).
3. CorebootPayloadPkg is practically dead by now, so delete the comment
about the problem with it.
Change-Id: Ic216c3437b2670638c845ee8964f831b80e18fce
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57461
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Install both versions of UEFITool, the one with the old engine and the
new one.
It's not possible to use both packages in the same environment, since
there is a collision between the names of the binary files. To make sure
a specific package is used, a new environment needs to be spawned with
the following command:
$ nix-shell -p <package_name>
The UEFITool binaries can be executed from the shell then.
Change-Id: Ia5d679c6e7cd01c2ab819bd6c085596a926c494d
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This patch fixes a few minor CBFS parsing edge cases that could lead to
unintended behavior: the CBFS attribute parser could have run into an
infinite loop if an attribute's length was (accidentally or maliciously)
invalid. A length of 0 would have caused it to read the same attribute
over and over again without making forward progress, while a very large
length could have caused an overflow that makes it go backwards to find
the next attribute. Also, the filename was not guaranteed to be
null-terminated which could have resulted in out-of-bounds reads on a
few error messages.
Finally, clarify the validity guarantees for CBFS header fields offered
by cbfs_walk() in the comment explaining cbfs_mdata.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie569786e5bec355b522f6580f53bdd8b16a4d726
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Intel TGL BIOS specification (doc ##611569) Revision 0.7.6 Section
7.2.5.1.5 recommends reserving the following resources for each PCIe
USB4 root port:
- 42 buses
- 194 MiB Non-prefetchable memory
- 448 MiB Prefetchable memory
This change enables reserving of resources for USB4 when mainboard
selects the newly added Kconfig SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES.
This is similar to the change for ADL in commit 8d11cdc6fa
("soc/intel/alderlake: Add Kconfig for recommended PCIe TBT resources").
Change-Id: I25ec3f74ebd5727fa4b13f5a3b11050f77ecb008
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
CBFS file with lenth of (UINT32_MAX - cbfs_file.offset + 1) causes
overflow, making cbfs_walk() being stuck in an infinite loop, and
checking the same file. This patch makes cbfs_walk() skip file headers
with incorrect data_offset or data_length.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I70020e347087cbd8134a1a60177fa9eef63fb7bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
It avoids the dependency on bison/flex, minimally speeds up the build
and also works around weird race conditions in some versions of bison
that need more investigation.
The issue this avoids manifests as a build error when creating
parser.tab.c:
input in flex scanner failed
make: *** [util/kconfig/Makefile.inc:66: build/util/kconfig/parser.tab.c] Error 2
Since the error happens within bison the alternative would be to make
bison part of our crossgcc environment to ensure that no broken OS
build is used.
BUG=b:197515860
TEST=things build with bison not installed
Change-Id: Ib35dfb7beafc0a09dc333e962b1e3f33df46a854
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
With parser.tab.h depending on parser.tab.c it's possible for make
to initiate the creation of parser.tab.c, then try to compile it,
even though parser.tab.h is still missing.
This isn't normally an issue yet because bison creates them both at
a time but with pre-compiled files this will become a problem.
Pattern rules support (until recently as a special case that no other
type of rule could implement) multiple targets that are actually
treated as "one command creates multiple output files" so use that
to state the relationship properly.
Change-Id: I4aa7eca9d3123808e0665a15a99c04fac7384940
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
By adding TEST_PRINT=1 to <test-name>-config field or by passing it as
a parameter to make one can enable printing in printk() and vprintk().
This can be helpful when developing unit tests.
Note, that to effectively enable or disable printk() printing to stdout,
test(s) have to be recompiled.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Ibdec8bb128f42ba4d9cb8bbb4a8c5159a2b52ac5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Manually maintaining a list of fields just to avoid printing some
unnecessary CPP guards isn't worth the maintenance burden. Instead,
always generate these guards, even if they guard nothing.
Change-Id: I6c84180d83ac39a895e02d196acb7074eb052d7f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57459
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The call to the `get_smbios_data` device operation is followed by
calls to unconditional default functions, which lacks flexibility.
Instead, have devices that implement `get_smbios_data` call these
default functions as needed.
Most `get_smbios_data` implementations are in mainboard code, and are
bound to the root device. The default functions only operate with PCI
devices because of the `dev->path.type != DEVICE_PATH_PCI` checks, so
calling these functions for non-PCI devices is unnecessary. QEMU also
implements `get_smbios_data` but binds it to the domain device, which
isn't PCI either.
Change-Id: Iefbf072b1203d04a98c9d26a30f22cfebe769eb4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Avoid SMBIOS type 16 Maximum Capacity showing incorrect
information when value of maximum capacity exceeds 32 bits by
extending the type.
Handle 0x0009, DMI type 16, 23 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: Single-bit ECC
Maximum Capacity: 4 TB
Error Information Handle: Not Provided
Number Of Devices: 6
Tested=On OCP Crater Lake, the SMBIOS type 16 shows expected
Maximum Capacity.
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Change-Id: Iaa79cc587808f1eab0a48e2ce1dab089e84e9721
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Daocheng Bu <daocheng.bu@intel.com>
Add additonal LPDDR4 speed grades. This is needed because the limited
set has casued confusion when the reported speed did not match
expectations. There does not seem to be a definitive list of LPDDR4
speed grades, so this list is derieved from JEDEC 209-4C and a survey
of commonly used LPDDR4 speed grades.
BUG=b:194184950
TEST=Boot, dmidecode -t 17 reports correct speed
BRANCH=None
Change-Id: Ie7706fd4ad5a7df68c07b8ca43261429ba140c61
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
1. K4U6E3S4AA-MGCR (Samsung)
BUG=b:192521391
BRANCH=dedede
TEST=Build and boot bugzzy board
Change-Id: Ic0b02559c671845a73a71bd57cd7237850c76645
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The MIPI source video data has a large variation (e.g. 59Hz ~ 61Hz),
anx7625 defines K ratio for matching MIPI input video clock and
DP output video clock. A bigger k value can match a bigger video data
variation. IVO panel has smaller variation than DP CTS spec, so decrease
k value to 0x3b.
BUG=b:194659777
BRANCH=none
TEST=Display is normal on Asurada
Change-Id: If3a09811999babda45e9a9a559dd447920109204
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Add mipi panel support for mrbland
- Setup gpio and modify LCD sequence.
- Use the following panel for mrbland:
AUO B101UAN08.3
BOE TV101WUM-N53
- Use panel_id to distinguish which mipi panel to use.
BUG=b:195516474,b:197300875,b:197300876
BRANCH=none
TEST=emerge-strongbad coreboot
Change-Id: Ib7cd2da429b114bf6bad5af312044a0f01319b46
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57336
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Our MIPI panel initialization framework differentiates between DCS and
GENERIC commands, but the exact interpretation of those terms is left to
the platform drivers. In practice, the MIPI DSI transaction codes for
these are standardized and platforms always need to do the same
operation of combining the command length and transfer type into a
correct DSI protocol code. This patch factors out the various
platform-specific DSI protocol definitions into a single global one and
moves the transaction type calculation into the common panel framework.
The Qualcomm SC7180 implementation which previously only supported DCS
commands is enhanced to (hopefully? untested for now...) also support
GENERIC commands. While we're rewriting that whole section also fix some
other issues about how exactly long and short commands need to be passed
to that hardware which we identified in the meantime.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I09ade7857ca04e89d286cf538b1a5ebb1eeb8c04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Moves MAX_EVENT_SIZE to commonlib/bsd/include, and renames it
ELOG_MAX_EVENT_SIZE to give it an "scoped" name.
The moving is needed because this defined will be used from
util/cbfstool (see next CL in the chain).
BUG=b:172210863
TEST=compiles Ok
Change-Id: I86b06d257dda5b325a8478a044045b2a63fb1a84
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Adds "clear" command to cbfsutil/elogtool tool.
"clear" clears the RW_ELOG region by using either:
* flashrom if no file is provided
* or using file write if an input file is provided.
The region is filled with ELOG_TYPE_EOL. And a
ELOG_TYPE_LOG_CLEAR event is inserted.
Additionally, it does a minor cleanup to command "list", like:
* use buffer_end()
* add "list" to the cmds struct
* and make elog_read() very similar to elog_write()
Usage:
$ elogtool clear
BUG=b:172210863
TEST=elogtool clear && elogtool list
elogtool clear -f invalid.raw
elogtool clear -f valid.raw
Change-Id: Ia28a6eb34c82103ab078a0841b022e2e5e430585
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
In order to get rid of pep.asl, skylake also needs to support runtime
generation of the Intel Power Engine, therefore add this support to
devices that have a discoverable PMC as well.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4bf0c4a338301b335fa78617e0f2ed5a9f4360ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Now that the PMC device is marked as hidden in devicetrees, the device
callbacks can be used instead of BOOT_STATE_INIT_ENTRY callbacks.
Note that this moves PMC initialization from BS_DEV_INIT_CHIPS to
BS_DEV_ENUMERATE, which aligns with other Intel SoCs.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: If292728ad975ba803fed6abea879f6f634470a11
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
FSP-S hides the PMC from the PCI bus when it runs, but there are still
initialization steps coreboot programs for the PMC. Therefore, change
all of the cannonlake mainboards to set the PMC as hidden in the
devicetree, which means the device will be skipped during enumeration,
but device callbacks are still issued as if the device were enabled.
TEST=Ran full patch train on google/dratini, disassembled SSDT and the
PEPD device matches what is in pep.asl. Also verified via dmesg that the
INT33A1 device is still initialized by the kernel.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib4a20ce9075ce7653388a5d3e281fe774bf89355
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
There is a use-case for generating the AML bytecode at runtime for the
Intel Power Engine device, which comes in a followup patch.
BUG=b:185437326
TEST=verified on google/brya and google/dratini by dumping SSDT and
verifying the PEPD device matches what was previously in the DSDT:
Scope (\_SB.PCI0)
{
Device (PEPD)
{
Name (_HID, "INT33A1")
Name (_CID, EisaId ("PNP0D80")
Method (_DSM, 4, Serialized)
{
ToBuffer (Arg0, Local0)
If ((Local0 == ToUUID ("c4eb40a0-6cd2-11e2-bcfd-0800200c9a66")))
{
ToInteger (Arg2, Local1)
If ((Local1 == Zero))
{
Return (Buffer (One)
{
0x63
})
}
If ((Local1 == One))
{
Return (Package (0x01)
{
Package (0x03)
{
\NULL,
Zero,
Package (0x02)
{
Zero,
Package (0x02)
{
0xFF,
Zero
}
}
}
})
}
If ((Local1 == 0x02)){}
If ((Local1 == 0x03)){}
If ((Local1 == 0x04)){}
If ((Local1 == 0x05))
{
If (CondRefOf (\_SB.PCI0.LPCB.EC0.S0IX))
{
\_SB.PCI0.LPCB.EC0.S0IX (One)
}
If (CondRefOf (\_SB.MS0X))
{
\_SB.MS0X (One)
}
If (CondRefOf (\_SB.PCI0.EGPM))
{
\_SB.PCI0.EGPM ()
}
}
If ((Local1 == 0x06))
{
If (CondRefOf (\_SB.PCI0.LPCB.EC0.S0IX))
{
\_SB.PCI0.LPCB.EC0.S0IX (Zero)
}
If (CondRefOf (\_SB.MS0X))
{
\_SB.MS0X (Zero)
}
If (CondRefOf (\_SB.PCI0.RGPM))
{
\_SB.PCI0.RGPM ()
}
}
Return (Buffer (One)
{
0x00
})
}
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie83722e0ed5792e338fc5c39a57eef43b7464e3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the get_supported_lpm_states() function to set the respective FSP
UPD.
TEST=with patchtrain on brya0,
/sys/kernel/debug/pmc_core/substate_requirements shows only the
substates that are applicable to the design (S0i2.0, S0i3.0).
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I5bb8b3671e78c5f2706db2d3a21b25cf90a14275
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
On some platforms, runtime firmware crashes write logs to the CBMEM
console. For those, since a crash reboots the system, by the time we
have a chance to run `cbmem` again the boot where the crash happened
will be the one before the "last" (current) boot. So cbmem -1 doesn't
show the interesting part, and cbmem -c potentially shows a lot that is
cumbersome to dig through. This patch introduces a new option cbmem -2
to explicitly show only the boot cycle before the last one.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I6725698f4c9ae07011cbacf0928544cebb4ad6f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
This reverts commit b90e6fdd25. Latest
releases of PSP does not load PSP verstage on S0i3 resume. Hence no need
to skip PSP verstage on S0i3 resume.
BUG=b:196400450
TEST=Build and boot to OS in Guybrush. Trigger a suspend/resume cycle
and then a reboot and ensure that the system boots to OS.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Iaeb92edb69662e6c06f4d0e3d7b760d4597bf650
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
ALC5682-VD/ALC5682-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define SSFC bit 9-11 in coreboot for codec within ec.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:193694180
TEST=ALC5682-VD/ALC5682-VS audio codec can work
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Ib458cf47909a2d7a65f086c5f30f85a16f78d589
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add the pin definitions for the remote GPIOs and the GPIO pin mux values
for the GPIO mode of those pins. For now, accessing the remote GPIOs is
only supported from the native coreboot code running on the x86 cores
and not from verstage on PSP or ACPI.
BUG=b:194524995
TEST=On Majolica with a Cezanne APU configuring GPIO 262 as output and
then toggling that GPIO in an infinite loop in the mainboard's bootblock
code results in GPIO 262 toggling as expected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0e57042e74da88503b36d6065e9500876287f8bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Some AMD SoCs have a 5th GPIO bank, the remote GPIO bank, which isn't
located right after the 4th GPIO bank, but instead at a different
location inside the APCIMMIO region. A difference to the first 4 GPIO
banks is that the corresponding GPIO MUX registers aren't in a separate
bank, but at the end of the remote GPIO region. So this remote GPIO
region only supports 48 GPIOs with a 32 bit configuration register each
and has the 8 bit GPIO MUX registers beginning at offset 0xc0 in the
remote GPIO region.
For now using the remote GPIOs from verstage on PSP isn't supported. To
support this, it would need to map acpimmio_remote_gpio and update the
pointer like it already does for acpimmio_gpio0, acpimmio_iomux and a
few others.
BUG=b:194524995
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic8d7ff677a99381a5558782b80b0c4cae67602db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Default VBOOT_HASH_BLOCK_SIZE is 1 KiB and increasing it to 4 KiB
helps in improving overall boot time since it reduces hashing and
body loading time.
Increasing it over 4 KiB doesn't result in significant improvement,
thus keeping the value at 4 KiB as of now.
Timing data:
Note that before Data is with 1 KiB block size.
|------------------------------------------------------|
| Stage | Block Size | Before | After |
|finished loading body| 4 KiB | 205,187 | 189,947 |
|finished loading body| 8 KiB | 205,187 | 188,708 |
|finished loading body| 16 KiB | 205,187 | 188,085 |
|finished loading body| 32 KiB | 205,187 | 187,793 |
|------------------------------------------------------|
BUG=b:188577893
BRANCH=None
TEST=Boot time for Brya improves by 20 - 25 msec
Change-Id: I9222761c7d58e4a370d3a41c651b6c169599d792
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change sets Irms config in FSP if TdcTimeWindow and TdcCurrentLimit
is set to non zero. It results VR TDC Input current to be treated as it
is root mean square.
This change also optimizes the check of TdcTimeWindow and TdcCurrentLimit
for TdcEnable UPD.
BRANCH=None
TEST=Build and boot brya with debug FSP and verify Irms UPD value
from logs
Change-Id: Ice5c775ef9560503109957a1ed994af1d287aafc
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
From ACPI specification, version 6.2 Errata A:
A `duty_width` value of 0 indicates that processor duty cycle is not
supported and the processor continuously runs at its base frequency.
Because Broadwell sets `duty_width` to 0, processor duty cycle is not
supported, and the value of `duty_offset` is ignored. For consistency
with Lynx Point, set `duty_offset` to 0.
Change-Id: I68cb85ec32a6cceda0cea29d76df6c6219b78a40
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Currently coreboot for the AMD SOCs only supports accessing the up to 4
main GPIO banks of up to 64 GPIOs each. Some AMD SoCs including Cezanne
have another GPIO bank in the ACPIMMIO region that can contain up to 48
GPIOs beginning with GPIO 256 which is called the remote GPIO bank. The
first 48 DWORDs of that ACPIMMIO bank are the 32 bit wide GPIO registers
and beginning at offset 0xc0 it has the corresponding 8 bit wide GPIO
MUX registers.
BUG=b:194524995
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ice4e3358de17ac2601621814978cdb70e6f2c926
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add and use the I2C_RESET_SCL_PIN macro for populating the i2c_scl_pins
array that is used for the sb_reset_i2c_peripherals call to bring the
I2C buses into a defined state.
TEST=Timeless build results in identical image for Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ifedc09d0bf745545fa0510df7d5037f02b9012a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Setting the usb_phy version and length in the soc code instead of devicetree.
That way the devicetree code does not have to reapeat it for different
AMD Cezanne based systems.
Tested on guybrush by changing phy settings in devicetree and then checking
the usb phy register.
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: I2db49e095672054b9b15042fb003a93b67e3a4c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The AMD Cezanne FSP expects a usb phy config structure ID of 0xd 0x6.
If the ID does not match, the FSP USB will not set up the phy.
Tested on guybrush by changing phy settings in devicetree and then checking
the usb phy register.
Cq-Depend: chrome-internal:4087511
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: I4fdb5af1cbc3c70cc113ef6f0fd9332e1a27f142
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The update_efs_spi_speed allows changing the SPI speed manually in a
binary that has already been built. This will allow binaries not built
for the EM100 SPI ROM emulator to be updated so that they will work.
There is a corresponding change that will check to see if the EFS value
has been modified from the original speed and will prevent coreboot from
updating the SPI speed and mode.
BUG=b:177233017
TEST=Update SPI speed in existing binary. See that SPI speed has
changed.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I905a9fd8bd93a28aab927dffecbbcf24934b9e03
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56644
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Even though `device` entries are children of `chip` entries in the
devicetree source format, the chips in the translated C structures
are only hooked up to device nodes. Hence, any chip with all its
settings will be silently dropped by sconfig if there is no device
node below it.
Let's adapt the parser to ensure that there is at least one `device`
entry. The intermediate `chipchildren_dev` rule applies until the
first `device` entry is found, then everything continues as before
with the `chipchildren` rule.
Change-Id: I54830bc1fc7d00a0605f3fe4d36a83ef57ef3312
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51119
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There was no code attached to this driver and hence one couldn't hook
it up to any device. Even if mentioned in the `devicetree.cb` it was
still dead code.
Change-Id: I12415ea9e0120b1d00524f8f39f9b2d02f46ba05
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set GPIO GPP_A8 as high to enable EN_PP3300_TOUCHSCREEN.
also reduce enable delay time for meet panel power sequence.
BUG=b:197668845
BRANCH=volteer
TEST=FW_NAME=chronicler emerge-volteer coreboot chromeos-bootimage
Verify no corruption is seen on the screen
panel power sequence meet spec
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I9a0c1d0afafb2c446fcb3d18e1a67573218614e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57103
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code under `cpu/x86/tsc` is only compiled in when its `Makefile.inc`
is included from platform (CPU/SoC) code and the `UDELAY_TSC` Kconfig
option is enabled.
Include `cpu/x86/tsc/Makefile.inc` once from `cpu/x86/Makefile.inc` and
drop the now-redundant inclusions from platform code. Also, deduplicate
the `UDELAY_TSC` guards.
Change-Id: I41e96026f37f19de954fd5985b92a08cb97876c1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57456
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allow to select the primary graphics device between the IGD and the
external PCIe GPU depending on the ONBOARD_VGA_IS_PRIMARY config.
The option sets the priority only. This means that if a high priority
is set for an external PCI device and it is not connected/not enabled,
then the device with a lower priority will be used, in our case it is
IGD.
TEST = Set PRIMARY_PCI and boot Linux on the Kontron mAL10 [1] with
the miniPCIe video adapter on the Silicon Motion SM750 controller. As
a result, the display connected to an external GPU device shows the
Tianocore logo + setup menu and the desktop.
[1] https://review.coreboot.org/c/coreboot/+/39133
Change-Id: Idcd117217cf412ee0722aff52db4b3c8ec2a226c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The eventlog requires RTC to provide correct timestamps, so we have to
turn on the config and add the common drivers.
BUG=b:199003609
TEST=check timestamp in 'mosys eventlog list'
BRANCH=none
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Change-Id: Ia382cd023fcbfdf2c1efeb7b32c0b99feb71effa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
A chip entry in the devicetree is not hooked up without a device
beneath it. It seems the intention was to leave these superio
drivers unconfigured, so there should be no harm to turn the
entries into comments.
Change-Id: I6b606f35eba089b74c562084772d95be41cac39c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add Kconfig option TIANOCORE_ABOVE_4G_DECODE to pass build option to
edk2 to enable or disable "Above 4G Decode". Disabling allows certain Linux
distributions to boot such as Qubes, Zorin and Proxmox.
Requires commit `2f6d4cbcc7fa49462e607baed7626524ccd59ad3` that is
present in the `uefipayload_202107` branch of MrChromebox's edk2
repository.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ia3b1d15196c0ec611431af29031682fea626d19d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
This aligns the GPIO MUX access more with the GPIO control register
access and will facilitate adding support for the remote GPIO bank. Also
change the GPIO number argument type to gpio_t.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4054656c5cc23ea942e8dd370fbbffca304755d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Introduce amdblocks/acpimmio_legacy_gpio100.h so that the old pre-SoC
chipsets can still access the raw GPIO100 and IOMUX ACPIMMIO registers
while only allowing GPIO accesses through the GPIO API on the SoCs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I18872dfa40d53ba8b0d7802eec52ede5e2ae617a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Since the raw GPIO MMIO register access is now only used inside the
gpio_banks block, the gpio_read32 and gpio_write32 functions can be
moved to that block to reduce the visibility and enforce the usage of
the functions provided by the gpio_banks block.
The iomux_read8 and iomux_write8 functions can't be easily moved to the
gpio_banks block, since it's also used in the pre-SOC AMD chipsets that
use the ACPIMMIO access functions directly.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia0d6dea72c6bebbbe6ce545bedfc74f91e0042c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
No need to do raw GPIO MMIO accesses when basically the same
functionality can be achieved by using existing APIs. Using the existing
GPIO API instead of raw GPIO MMIO register accesses allows containing
all direct GPIO MMIO accesses inside the common AMD GPIO code which will
be done in subsequent patches. Since the value parameter of gpio_set is
int, change the type of the val parameter of drive_scl to int as well
even though I'm not sure why a signed integer was used for this in the
common GPIO API. Since program_gpios already configures the SCL GPIOs as
outputs, gpio_set can be used in drive_scl which only sets the output
value, but doesn't configure the direction.
TEST=The waveform on the SCL pin of I2C3 on a barla/careena Chromebook
looks similar to the same as before during the reset_i2c_peripherals
call, but due to the additional overhead of the read-modify-write to the
GPIO register instead of just a write, the pulse width gets about 50%
longer. Since the udelay call in drive_scl still has an open TODO to
make this configurable and the pulses being longer is in the safe side,
this side-effect can be addressed in a follow-up patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic323cebc1c83ecd6f0e1fbab419c69489d77face
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
drive_scl in soc/amd/common/block/i2c/i2c.c writes the raw GPIO MMIO
configuration register and drives it as output, so don't initially
configure the GPIO as input with no pull up/down. This is a preparation
to use the common AMD GPIO access functions instead of the raw register
accesses, since the gpio_set function only sets the output value, but
doesn't reconfigure the direction. Using gpio_output there instead would
reconfigure the direction as well, but would result in doubling the
number of MMIO accesses, so just configure the GPIOs correctly right
away to avoid that.
TEST=The waveform on the SCL pin of I2C3 on a barla/careena Chromebook
looks exactly the same as before during the reset_i2c_peripherals call.
This was probed at the SCL pad of the unpopulated I2C level shifter on
the side that is connected to the SoC.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8e94afe0c755a02abcc722d5094e220d8781f8f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56807
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
NVMe needs extra time to run boot process, enable power and deassert reset for NVMe earlier in the boot flow that gimble can successfully boot into OS with non-serial coreboot.
BUG=b:198405404
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ib76965db2a6cd0c19be4043fec73af297a619c7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57359
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
copy config from guybrush reference board.
remove wwan & speaker amp due to the different solution is
used on nipperkin.
BUG=b:194031783
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I58a9b8393a965a9c793802d3e660829863b74375
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The COMe module connector implements 8 GPIO lines from the CPLD/EC pins.
Use the Kempld GPIO driver[1] to configure these pins in accordance with
the COM Express Module Base Specification [2].
TEST = Set different logic states for the pin configured as outputs and
check them with an oscilloscope.
[1] CB:47595 , Change-Id: Id767aa451fbf2ca1c0dccfc9aa2c024c6f37c1bb
[2] page 79-81, PICMG (R) COM.0 Revision 3.0 COM Express (R) Base
Specification - March 31, 2017.
Change-Id: I7d354aa32ac8c64f54b2bcbdb4f1b8915f55264e
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54380
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All KBLRVP variants select the `INTEL_LPSS_UART_FOR_CONSOLE` Kconfig
option and set `UART_FOR_CONSOLE` to `2`, so that UART #2 is used as
coreboot console. However, the LPSS console driver requires the LPSS
UART to be memory-mapped (and not I/O-mapped, like Super I/O UARTs).
KBLRVP variant RVP8 uses `PchSerialIoLegacyUart` for UART #2, which
makes FSP-S configure UART #2 in legacy, I/O-mapped mode. This most
likely results in the UART console not working after FSP-S has run.
This change updates RVP8 to use `PchSerialIoSkipInit` for UART #2, like
the other KBLRVP variants do.
Change-Id: Ic5c78f5895fe1dd5e7be6ef7aec3de6940dd2475
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
The I2C #4 and I2C #5 devices do not exist on PCH-H. Disable the devices
using the PCH-H variants' overridetrees (the base devicetree enables I2C
#4), set the `SerialIoDevMode` entries to `PchSerialIoDisabled` and drop
inapplicable I2C #4 voltage settings.
Change-Id: I56f34fa2004993d2123ccd5c1008fd71682ec2bd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Get rid of several unused PCH PCI device macros. These macros expand to
a call to the `pcidev_path_on_root_debug()` function, which only exists
to debug bad code. If needed, these macros should be reimplemented with
the `pcidev_path_on_root()` function instead.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I366e064f3fe708b55fb381aee25b2795b1c61142
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55529
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change adds a new Kconfig `SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES`
that can be selected by mainboard to reserve hotplug resources for
USB4 at the SoC level. `ADL_ENABLE_USB4_PCIE_RESOURCES` is dropped
from soc/intel/alderlake and instead the newly added Kconfig is now
used. This new Kconfig is added so that the same config can be used
across different platforms. In following changes, this Kconfig is
utilized by TGL as well.
Change-Id: Id7c359a0e255c43c2732f6cbe287bc7da14a46e3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
There are multiple HECI clients in the CSE. heci_send_receive() is
sending HECI messages to only the MKHI client. Add an argument to
heci_send_receive() function to provide flexibility to the caller to
select the client for which the message is intended.
With the above change heci_send() and heci_receive() functions are
no longer required to be exposed.
In the follow-up patches there will be messages sent to one other
client.
BUG=None
BRANCH=None
TEST=Build and boot brya. HECI message send and receive to MKHI client
is working. Also, MEI BUS message to disable bus is working.
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: Icde6d0155b62472b6a7caadc5fc8ea2e2ba6eb0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add new thermal control mechanism for pch device under dptf driver.
This provides support of different control knobs for FIVR.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I035d2844b9ba6a9532ae006fc1c43e34cb94328a
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Configure I2C high / low time in device tree to ensure I2C
CLK runs under I2C_SPEED_FAST (400 kHz).
Measured I2C frequency just as below after tuning:
Touchpad: 386.7kHz
Touchscreen: 387.4kHz
Audio: 385.7kHz
P-sensor: 378.1kHz
BaUG=b:197247706
BRANCH=dedede
TEST=Build and check I2C clock is under 400kHz
Signed-off-by: stanley.wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Ic5d5660181f36f161ae04cbf5003f6d7ad4bc16f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add MT53E512M32D1NP-046 WT:B supported memory part in the
mem_parts_used.txt and generate the SPD ID for the part. Manufacturer
is Micron, and the memory part is 1anm Tech, difference to 1xnm Tech
on MT53E512M32D2NP-046.
BUG=b:194223174
BRANCH=dedede
TEST=Build the gooey board.
Change-Id: I7b83126a2bf98bb9d0ca05d397c288e0d99ed781
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57310
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently maximum VBT data size for Jasper Lake is 8KB, but Bugzzy
would use VBT data over 8KB. This change makes use of Kconfig option to
increase the maximum VBT data size to 9KB for Jasper Lake.
BUG=b:194029827
BRANCH=dedede
TEST=build and boot bugzzy and verify fw screen is loaded
Change-Id: I0abe1ba5609b48a8a8b15f88bec28342ce26c78f
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57201
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Guybrush based boards must usa a dedicated eSPI alert#.
Must be open drain to prevent power leaks.
Keep guybrush reference board in-band since alert# may not be connected.
BUG=b:198409370
TEST=Build guybrush and nipperkin, boot guybrush
BRANCH=None
Change-Id: I4b23bfc6a1167aebfde5acd524fda043b63163dc
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Rename two functions that have `walk` in their name but do not perform
any walk. The new names are derived from the comments just above these
functions' definitions. Also, remove these now-redundant comments.
Change-Id: I380a5b60b3f4e820e8f6d6f960826de97c0446be
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57361
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Like USE_AMD_BLOBS and USE_QC_BLOBS in the case of the AMD and Qualcomm
repos, FSP_USE_REPO controls if the Intel FSP repo will get checked out
and will be available during the Jenkins runs. ADD_FSP_BINARIES will get
selected in drivers/intel/fsp2_0/Kconfig when FSP_USE_REPO is selected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I72faa6f9e5f2b06ab7cd43595ae0b49bf4d39630
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Normally, selecting FSP_USE_REPO will select FSP_FULL_FD which then will
configure the proper paths for FSP_M_FILE and FSP_S_FILE. The override
in these two boards caused FSP_M_FILE and FSP_S_FILE being empty despite
ADD_FSP_BINARIES being selected by FSP_USE_REPO which is an invalid case
that needs to be avoided, so remove the board-level override of those
two options.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I20c8cebea8327d59f0f33d05b824a74bf2121f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The ADD_FSP_BINARIES override in the mainboard's Kconfig caused this
option to not be selected when FSP_USE_REPO is selected. Remove the
override to fix this problem. These two boards are the only ones in tree
that had an override for this option, so now the ADD_FSP_BINARIES option
is only defined in drivers/intel/fsp2_0/Kconfig.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I23439f3134eef9460625addbff7efd64c5f65ae5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This option is neither selected nor usable for the only remaining SoC
that uses this code, so drop the remaining parts. configure_hudson_uart
isn't called anywhere and isn't even compiled, since it's guarded by an
#if CONFIG(HUDSON_UART) block and the HUDSON_UART Kconfig option isn't
selected anywhere. Both the offsets used in the iomux_write8 calls and
the UART controller itself aren't listed in the BKDG #52740 Rev 3.05 for
the AMD Family 16h Models 30h-3Fh APUs which is the only SoC that uses
this code, so the code didn't even apply for this chip.
TEST=Timeless build for pcengines/apu2 results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3f462d1f83a0f1ba851329ebebb1f3263267fdc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This config selected ADD_FSP_BINARIES even though HAVE_INTEL_FSP_REPO is
only defined for Apollolake and not Geminilake that resides in the same
SoC directory and uses the same Kconfig file. This results in the paths
to the FSP binaries not being defined, in which case the
ADD_FSP_BINARIES option shouldn't be selected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I95123c4930b44a3b76c87768e130eb7359bbf625
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
EGPIO132 is the last documented GPIO on the GPIO controller in the NDA
version of the BKDG for AMD Family 16h Models 30h-3Fh Processors (#52740
Rev 3.06) which is the only SoC using this code, so define
SOC_GPIO_TOTAL_PINS as 133, since the internal GPIO numbers are
0-indexed. This definition will be needed the subsequent patch that'll
add the remote GPIO support to the common AMD GPIO code to make sure
that the compiler can optimize out the code path needed to support the
remote GPIO access which isn't available on this platform anyway.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I877d462c5e753c9bbb3461dbb10cde2adc2cb12c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
If a USB_MUX_EVENT happens while the AP is in S3 during powerdown
transtion (S0->S3->S5), this will cause the device to boot again after
it has finished sequencing down to S5. Since S3 is not POR for ChromeOS
devices anymore, change this event to wake from S3 and S0ix to just
S0ix.
BUG=b:197039097
TEST=abuild
Change-Id: I91e5e0ab8301377817875b6fa9e3c0e1f96c1465
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Add NixOS configurations for bootable live systems containing a set of
tools which might be useful for firmware development in general and for
working on coreboot.
There are two configurations provided. One for console-only and a
graphical one, which is mostly the same as the console image but it
comes with Gnome Shell as window manager and some graphical tools in
addition.
An image can be built using `build-console.sh`, respectively
`build-graphical.sh`. The resulting iso image can be found in
`result/iso/`.
The console image results in ~700MB, while the graphical one results in
~2GB.
Change-Id: Iaf49d198e99781434bd89d2a8a125a4988b77e1c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This patch updates debug message to specifically the case when SMBIOS
table 7 write would abort due to either `unknown` CPU or CPU `doesn't
have support for deterministic cache cpuid leaf`.
Change-Id: I288593b3f78ab858bf66c689e7cfb6ba2ff746d0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
`cpu_get_cache_info_leaf()` function is responsible to report leaf
value for CPU that have support for deterministic cache cpuid. As per
available datasheets from AMD and Intel the supported CPUID leafs are
0x8000_001d for AMD and 0x04 for Intel. Hence, this CL skips returning
default leaf value as `0`.
TEST=Verified fixes: e2b5fee3b0 (arch/x86: smbios write 7 table using
deterministic cache functions) hang issue on ASRock E350M1.
Change-Id: Iee33b39298e7821ac5280d998172b58a70c8715b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57305
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are two different types of 682 SKU available with TDP
of 28W and 45W. This patch fix override values for power
limits for these 682 SKU. This patch also sets power limit
values dynamically based on machine ID and CPU TDP of SKU.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I796e56321ae9c8312530a4b8986cd73a2245f5fa
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57290
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
copy existing QSPI driver from /soc/qualcomm/sc7180 to common folder.
This common QSPI driver works in master mode and provides read/write
operation for the slave devices like flash.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I5b3816b823e14db1dd13f1eb4a6761c7a61604b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Introduce DDR One-Time-Training Support
Device reboots without training from second iteration
and also DDR training data is 32kb size, hence update
required in memlayout and to sync with upstream changes
the Fmap size even got bumped up.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: I81038c5c7802c154f4310509c6c64710580b8ce4
Signed-off-by: Sudheer Kumar Amrabadi <samrabad@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
It supports the clock consumers for QUP, SDCC, PCIE, Display to be able
to configure & enable the desired clocks.
The clock driver also supports reset of subsystems like AOP and SHRM.
Also add support for Zonda PLL enable for CPU in common clock driver.
Refactor the SC7280 clock driver to use the common clock driver APIs.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: I590a93cda0d6eccb51b54692b620d43ccacede77
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50580
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
southbridge/amd/pi/hudson uses the common GPIO bank access code from
soc/amd, but doesn't provide all functionality that would be needed to
use the full functionality. Add a Kconfig option that switches off some
functionality in the common SoC GPIO access code, so that more of the
functionality proviced by the common SoC GPIO code can be used in the
AMD binaryPI chipset and board code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib10d5d5580aab30a359aa001bb6fc7e9fdb8fc41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56783
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The mapping of the package GPIO numbers to the GPIO numbers on the GPIO
controller isn't a 1:1 one, so add a comment about that to avoid
confusion. Also change the comment style to match the style guide.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie30bf5483ea2e2516d7e3fdd21ea9338362e526e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Make adding the FSP-T file to CBFS depend on both ADD_FSP_BINARIES and
FSP_CAR Kconfig options being set. The FSP_T_FILE Kconfig option depends
on both, so also check if both are selected in the Makefile where it
tries to add the FSP-T to the CBFS.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Furquan Shaikh <furquan@google.com>
Change-Id: Id347336f2751c6d871f31d89c30a1222037c2d69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The clock driver supports configuring the general purpose PLLs,
configuring the root clock generator (RCG), enable clock branch, enable
gdsc and also the block resets.
The common clock driver exposes PLL configuration functions and also
different Agera PLL enable functions for the CPU PLLs.
While at it, the common driver also supports reset of subsystems like
AOP and SHRM.
SC7180 clock driver is also refactored to use the common clock
driver APIs.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Change-Id: I03d1b4a2fb90303c7259ec08f312d78b4e33ec39
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
As we move to use the common clock driver, the sc7180 clock driver,
watchdog and display drivers requires few cleanups, thus update the
impacted drivers.
Earlier the display client is expected to provide 2n divider value,
as the divider value in register is in form "2n-1".
mdss_clk_cfg.div = half_divider ? (half_divider - 1) : 0;
The older convention in the upcoming patches would be replaced with
the common macro of QCOM_CLOCK_DIV, thus need the divider needs to
be updated.
mdss_clk_cfg.div = half_divider ? QCOM_CLOCK_DIV(half_divider) : 0;
To accommodate impacting the functionality, the half_divider is taken
care in the clock driver.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 development board
Change-Id: Ic334fd0d43e5b4b1e43a27d5db7665f0bc151d66
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
CONFIG_DRIVERS_INTEL_MIPI_CAMERA and CONFIG_SOC_INTEL_COMMON_BLOCK_IPU
are getting selected for all ADLRVPs irrespective of ADL-P and ADL-M
(internal and external EC SKUs) hence, select those Kconfigs from
mainboard Kconfig rather Kconfig.name.
Also, select DRIVERS_INTEL_SOUNDWIRE as per alphabetical order.
TEST=No changes are seen while the .config file is getting auto
generated.
Change-Id: I62d5ec19c3364da79ebe7287b1b3d6eb2a0efca0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
variant_has_pcie_wwan() was always coming back as disabled because
find_dev_nested_path() couldn't find the device until the domain was
added to the array.
BUG=b:193036827
TEST=Boot guybrush with PCIe & USB WWAN devices.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Id94fa0b0ff5c29fa447e869220d27ccfe61438c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add support for DSM methods as per the connectivity document
559910_Intel_Connectivity_Platforms_BIOS_Guidelines_Rev6_4.pdf
BUG=b:191720858
TEST=Check the generated SSDT tables for DSM methods
Change-Id: Ie154edf188531fe6c260274edaa694cf3b3605d3
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add support for the WTAS ACPI BIOS configuration table as per the
connectivity document:
559910_Intel_Connectivity_Platforms_BIOS_Guidelines_Rev6_4.pdf
BUG=b:193665559
TEST=Generated SAR file with the WTAS related configuration values and
verified that the SSDT has the WTAS ACPI table.
Change-Id: I42cf3cba7974e6db0e05de30846ef103a15fd584
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add support for the PPAG ACPI BIOS configuration table as per the
connectivity document:
559910_Intel_Connectivity_Platforms_BIOS_Guidelines_Rev6_4.pdf
BUG=b:193665559
TEST=Generated SAR file with the PPAG related configuration values and
verified that the SSDT has the PPAG ACPI table.
Change-Id: Ie8d25113feeeb4a4242cfd7d72a5091d2d5fb389
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Existing SAR infrastructure supports only revision 0 of the SAR tables.
This patch modifies it to extend support for intel wifi 6 and wifi 6e
configurations as per the connectivity document:
559910_Intel_Connectivity_Platforms_BIOS_Guidelines_Rev6_4.pdf
The SAR table and WGDS configuration block sizes were static in the
legacy SAR file format. Following is the format of the new binary file.
+------------------------------------------------------------+
| Field | Size | Description |
+------------------------------------------------------------+
| Marker | 4 bytes | "$SAR" |
+------------------------------------------------------------+
| Version | 1 byte | Current version = 1 |
+------------------------------------------------------------+
| SAR table | 2 bytes | Offset of SAR table from start of |
| offset | | the header |
+------------------------------------------------------------+
| WGDS | 2 bytes | Offset of WGDS table from start of |
| offset | | the header |
+------------------------------------------------------------+
| Data | n bytes | Data for the different tables |
+------------------------------------------------------------+
This change supports both the legacy and the new format of SAR file
BUG=b:193665559
TEST=Checked the SSDT entries for WRDS, EWRD and WGDS with different
binaries generated by setting different versions in the config.star
Change-Id: I08c3f321938eba04e8bcff4d87cb215422715bb2
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
GPIO PM was disabled for brya to evaluate if longer interrupt pulses
are required for ADL. Since ADL requires 4us long pulses (EDS:626817),
GPIO PM can be enabled. All devices currently tested on brya support 4us
long pulses. This change drops the GPIO PM override and re-enables
dynamic GPIO PM.
TEST=Boot brya to OS, ensure no TPM errors.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0c7b66b5514d8b80775ab7578ce7b12181af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56926
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It doesn't make sense to store the orientation field directly in the
panel information structure, which is supposed to be reuseable between
different boards. The thing that determines orientation is how that
panel is built into the board in question, which only the board itself
can know. The same portrait panel could be rotated left to be used as
landscape in one board and rotated right to be used as landscape in
another. This patch moves the orientation field out of the panel
structure back into the mainboards to reflect this.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If2b716aa4dae036515730c12961fdd8a9ac34753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57324
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Windows will write to the century byte (0x32), causing the option table
checksum to be invalid and reset all options to their default values.
Move options and checksum to start after the century byte.
Change-Id: Ia395acacda1e251251c880587bbf61d7ee81ba3d
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
It turns out that putting a device ref in an overridetree at a different
point in the tree will generate a duplicate device definition, such that
the change introducing this support was ignoring the device presence
specified by overridetree.cb and only using the baseboard configuration.
I believe testing of that change was not redone after the baseboard was
changed to disable the MST, so that conflicting behavior was not
noticed.
The incorrect behavior generated a disabled device for the MST at the
location specified by the baseboard, and one with the probe as a child
of the soc. At runtime this did a fw_config probe of the "I2C 00:4a"
device, and later probed a different "I2C 00:4a" which was already
disabled. As the disabled one came later, it seems to have completely
disabled the MST, discarding the results of the variant-specific probe.
BUG=b:185862297
TEST=10EC2141 device is now present on a Dali berknip
BRANCH=zork
Change-Id: I2a8feb544f3fc198fe6313b226ad8995aad31c3e
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57298
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The patch is to fix "Not a usable UEFI firmware volume" issue when
creating CBFS/flash image. This issue is caused by adding FvNameGuid
in UefiPayloadEntry.fdf in EDKII. There is an ext header between header
of Fv and header of PayloadEntry in Fv with FvNameGuid. The ext header
causes the UefiPayloadEntry to be found incorrectly when parsing Fv.
Commit in EDKII: 4bac086e8e007c7143e33f87bb96238326d1d6ba
Bugzila: https://bugzilla.tianocore.org/show_bug.cgi?id=3585
Signed-off-by: Dun Tan <dun.tan@intel.com>
Change-Id: Id063efb1c8e6c7a96ec2182e87b71c7e8b7b6423
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57296
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: King Sumo <kingsumos@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The new CBFS stack was written to try to isolate cases of single file
corruption as far as possible and still make other files avaialble (at
least as long as verification is disabled and they can still be found at
all). For most cases of header corruption, it will just continue trying
to parse the next file. However, in cases where parts of the file extend
beyond the end of the rdev, we have been relying on the range checking
of the rdev API rather than doing it explicitly.
This is fine in general, but it causes the problem that these errors
cannot be distinguished from I/O errors, and I/O errors always make the
whole cbfs_walk() fail. That means we will not return a successful
result from cbfs_mcache_build(), and leads to an odd discrepancy in how
certain kinds of corrupted CBFSes are treated with and without mcache.
This patch adds an explicit range check to make the behavior consistent.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ice2b6960284bd0c19be35b0607e5e32791e7a64c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
When running multiple tests, e.g. by using unit-tests target, it is hard
to differentiate, which output comes from which file and/or
configuration. This patch makes the output easier to analyze and
understand by using new wrapper macro cb_run_group_tests(). This macro
uses __TEST_NAME__ value (containing test path and Makefile test name)
as a group name when calling cmocka group runner.
Example:
Test path: tests/lib/
Makefile test name: cbmem_stage_cache-test
Test group array name: tests
Result: tests/lib/cbmem_stage_cache-test(tests)
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I4fd936d00d77cbe2637b857ba03b4a208428ea0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
On mainboards with Cezanne SOC, serial enabled FSP_M binary size is
greater than the size allocated in DRAM. Increase the allocated size for
FSP_M binary in DRAM to handle both debug and release FSP_M binaries.
Also adjust the verstage load address accordingly.
BUG=None
TEST=Build and boot to OS in guybrush with both debug and release FSP_M.
Perform warm, cold reboot and suspend/resume cycling for 10 iterations.
Change-Id: Ic6f90041e258039e691cbdb3a978cfe1f782642a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57293
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Before this patch EXTRA_CFLAGS were placed before many other options.
This made overriding impossible even, when necessary. This patch moves
EXTRA_CFLAGS to be placed after original CFLAGS, thus making option
overriding possible.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: If8394b151696eee4bd736d2fb1ad340209e05fbb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57181
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable this feature, and it can use the probe statement in devicetree
to cache of fw_config field as oem string.
BUG=b:191931762
TEST=With CBI FW_CONFIG field set to 0x8,
set probe AUDIO MAX98390_ALC5682I_I2S_4SPK in devicetree
dmidecode -t 11
OEM Strings
AUDIO-MAX98390_ALC5682I_I2S_4SPK
Change-Id: I93cd9ef2d1ad963e66c422cff17b083abf731046
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
When the override functionality looks for device match, check that
the probe list for both the devices matches exactly if probe list
exists for the base device. This ensures that if there are two devices
with same identity (e.g. I2C address or USB port #) but using
different properties (registers) controlled by different probe
statements, then the two devices are not incorrectly matched as the
same device.
The check for base device having a probe list is performed before
comparing the probe lists because a base device might not really have
any probe requirements at all. So, when overriding such a device,
there is no need to check for the probe list match.
BUG=b:187193527
TEST=Verified by adding two I2C devices in the override tree with the
same I2C address and chip but different probe statements and confirmed
that both the devices are present in generated static.c file.
Change-Id: Ib18868b336cf4ffc9aa38aee7c6f333a35d32fce
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change moves the hda device enabling from baseboard device tree
to override tree for the variants that did not provide any hda
specific nodes. This ensures that the probe statements are correctly
selected by the variant depending upon the configurations it
supports.
Change-Id: Ib7b36468f17fbd65eb3d7d9355fcf78148aeb44a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57123
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
volteer baseboard was currently enabling TBT(USB4) devices in
baseboard devicetree and also selecting the Kconfigs required for
resource allocation above 4G for the USB4 controllers. However, not
all volteer devices have USB4 support. This change fixes USB4 enabling
for volteer family by making the following udpates:
1. TBT devices are moved from baseboard devicetree to individual
override trees for the variants that actually support USB4.
2. When moving TBT devices to override tree, tbt_pcie_rp0 is marked as
on instead of hidden for all variants other than volteer
reference. This is because volteer reference is the only device that
has an asymmetric support for USB4 (i.e. does not support USB4 on C0
port).
3. Kconfig selection for PCIEXP_HOTPLUG is moved to Kconfig.name for
these variants.
Change-Id: If380dcb1ea1633b3a1d6932e769cb6ed0a2761c7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57112
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Processor hang is observed while hot plug unplug of TBT device. BIOS
should execute TBT PCIe RP RTD3 flow based on the value of
TBT_DMA_CFG_VS_CAP_9[30]. It should skip TBT PCIe RP RTD3 flow, if
BIT30 in TBT FW version is not set.
BUG=b:194880254
Change-Id: Ie3577df519f64c6f7270dc5537278af76536774e
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56503
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In CB:56884 we discussed changing the default fast_read speed from
66MHz, which some platforms may not be capable of running, to 33MHz,
which should be generally suitable for all platforms. This same
change has been applied to the default for all SPI speeds.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ibf926df6829ffdcbae947aaa245356f219615ce8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57148
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add buffer_end() function to common.h. This function returns a
pointer to the end of the buffer (exclusive).
This is needed by elogtool util. (See the next CL in the chain).
BUG=b:172210863
Change-Id: I380eecbc89c13f5fe5ab4c31d7a4fef97690a791
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
FSP-S configures the GPIOs for enabled SerialIO devices. However, Poppy
boards only enable UART 0 because it's function 0 of PCI device 30, and
the PCI specification requires that function 0 of multifunction devices
be implemented if other functions are implemented as well.
Nautilus got remedied in commit 8a1f095e50
(mb/google/poppy/variants/nautilus: Update camera power enable GPIOs) by
using `PchSerialIoSkipInit` for UART 0, which tells FSP to not touch the
SerialIO device. This way, it remains enabled and the GPIO settings will
not be overwritten by FSP.
However, not all variants do this, but use some UART 0 pads as GPIOs. To
prevent any issues, configure UART 0 as `PchSerialIoSkipInit` on all the
variants.
Change-Id: I7e3a61769ef9e3b348ce84c663f67d3c4c5d9485
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55236
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make sure that the 48MHz clock output that is typically used as a clock
source for an I2S audio codec or a Super I/O chip.
TEST=On Guybrush before and after this patch the final state of
MISC_CLK_CNTL0 is 0x1006044, so BP_X48M0_OUTPUT_EN is set in both cases.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I38be344a95ccf166c344b2bddcb388fea437a4df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56528
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds code to print the current SPI speeds for each of the 4
different speeds, Normal, Fast-read, Alt-mode, & TPM. It also displays
the SPI mode and whether or not SPI100 mode is enabled.
BUG=b:194919326
TEST: Display the speed, change speeds, show that new speeds are the
expected values.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I7825a9337474c147b803c85c9af7f9dc24670459
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Get the settings for fast-read and mode from EFS, and reprogram those.
Program Normal reads, Alt-mode, and TPM speeds from Kconfig settings.
BUG=b:195943311
TEST=Boot and see that SPI was set to the correct speed & mode
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I8a24f637b2a0061f60a8f736121d224d4c4ba69b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The common_i2c_save struct isn't specific to the I2C code and since it
contains the state of the GPIO control & status register and the state
of the GPIO MUX register, move it to include/amdblocks/gpio_banks.h and
rename it to soc_amd_gpio_register_save.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If7cd47e5a32427d856948e319de8dfad8c928e96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
No need to strip the quotes of the FSP-M file path in the size check and
it's always a good idea to not remove the quotes around file paths that
will get passed as parameters to shell programs so that spaces in the
path can't cause malfunction.
TEST=All cases still behave as expected for Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Nico Huber <nico.h@gmx.de>
Change-Id: Ieeea84b5861f9d15b2472208432169dc8e3f0049
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This fix will enable PCIe x1 slot for ADL-M LP4 and LP5 RVPs.
The BDF for this PCIe slot is pci is: 0000:00:1d.0
TEST = show device command:
$ lspci -s 00:19.0
expect this:
00:19.0 Serial bus controller [0c80]: Intel Corporation Device 51c5
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ia988fa0b5d8fefe68503b39843aab06c4229b36f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57053
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Power down the eMMC controller via the AOAC interface when it's not
enabled in the devicetree.
BUG=b:184978118
TEST=On guybrush the unused eMMC controller is disabled in AOAC after
applying this patch. Before this patch it was enabled.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I18f4626a29fdc422218777058341b0eae401bcd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55537
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
NCT6776's data sheet does say that the virtual LDN of GPIO base should
be 0x308, and most mainboards using it usually correctly config it in
devicetree.cb under the path 2e.308, but in nct6776.h it used to be
defined as 8 from the beginning (an ancient commit 1e3a22649a, lately
revived in commit f95daa510d), identical to the LDN of WDT, which
eliminates the definition of value 2e.308, and makes related resource
allocations unable to take effect. (in log we can find "PNP: 002e.308
missing read_resources" if 2e.308 is enabled and assigned with
resources)
In this commit, NCT6776_GPIOBASE is set to a value consistent with the
data sheet.
With this commit, resources under 2e.308 of NCT6776 can be allocated
successfully.
Change-Id: I604bad7ab34a8f57262fdec508e5952cf8eabf1c
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
When CONFIG_FSP_M_FILE isn't defined, the parameter of the file-size
call evaluates to an empty string, so the file-size call will run
"cat | wc -c" which will cause make to get stuck in there. Also print a
message when no FSP-M file is specified that the resulting image won't
boot successfully.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b02774e2c79d12554fd076aa01bbe972176f372
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Since all mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, make it the
default by changing its enum value to 0 and remove its configuration
from all related devicetrees.
If `common_soc_config.chipset_lockdown` is not configured with
something else in the devicetree, then `CHIPSET_LOCKDOWN_COREBOOT`
is used.
Also, add a release note for the upcoming 4.15 release.
Change-Id: I369f01d3da2e901e2fb57f2c83bd07380f3946a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO_CODEC_SOURCE field of fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:194356991
TEST=ALC5682-VD/ALC5682-VS audio codec can work
Change-Id: I71b824c42c13cc2a8bebe0072de4a65ce238f074
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Update the USB port configuration based on driblee schematic.
USB2 [0]: USB Type C Port 0
USB2 [1]: None
USB2 [2]: USB Type A Port 1
USB2 [3]: None
USB2 [4]: None
USB2 [5]: Camera UFC
USB2 [6]: None
USB2 [7]: None
USB3 [0]: USB Type C Port 0 (M/B side)
USB3 [1]: None
USB3 [2]: USB Type A Port 0 (M/B side)
USB3 [3]: None
BUG=b:195622487, b:191732473
BRANCH=keeby
TEST=FW_NAME="driblee" emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Id9f4f8db98cb20db1c3936c65689a847a7802b9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56997
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will add ACPI information to enable WACOM touchscreen.
TEST=Boot DUT and issue command:
$ ls -al /sys/bus/i2c/devices
WACOM PWB-D893 device should be listed and touchscreen should be functional.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I37c0831485135fda3284dda6b61f4825b7fc51a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Add the support RAM parts for Corori.
Here is the ram part number list:
DRAM Part Name ID to assign
H9HCNNNBKMMLXR-NEE 0 (0000)
K4U6E3S4AA-MGCR 0 (0000)
lp4x-spd-1.hex # ID = 0(0b0000) Parts = H9HCNNNBKMMLXR-NEE, K4U6E3S4AA-MGCR
BUG=b:196744958
BRANCH=keeby
TEST=emerge-keeby coreboot
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: Ia11b5db145deeea838a8f5949accdb11e13342f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56988
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Follow schematic to modify USB port settings.
USB2 [0]: USB Type C Port 0
USB2 [1]: None
USB2 [2]: USB Type A Port 0
USB2 [3]: None
USB2 [4]: None
USB2 [5]: Camera UFC
USB2 [6]: None
USB2 [7]: Integrated Bluetooth
USB3 [0]: USB Type C Port 0 (M/B side)
USB3 [1]: None
USB3 [2]: USB Type A Port 0 (M/B side)
USB3 [3]: None
BUG=b:196998272
BRANCH=keeby
TEST=FW_NAME="corori" emerge-keeby coreboot
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I2045b2be9d79bfd394fa4520faa0fb552a704206
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57010
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the anahera variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:197850509
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_ANAHERA
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Id7649d56a8d6f85d12208f7ddaf2f71a7fe98e8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This keeps the default of EFS_SPI_SPEED at 66.66Mhz for the non-EM100
case, but switches the EFS_SPI_READ_MODE setting from Dual IO (1-1-2) to
Quad IO (1-1-4) for the non-EM100 case. This patch adds a special config
for the EM100 emulator case that has limited SPI frequency support.
Tested on Majolica by Martin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8996c2bf606ccd21686092beac8d96b22c0b7869
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56815
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Variants only need to provide the SPD index and whether said index
corresponds to a dual-channel configuration, which can be achieved
without using `pei_data`. Add two functions that return the values
and use them in `spd.c` at mainboard level.
Change-Id: I9bc4527057d4a771883c8cc60da2501516d6fb94
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Add GPIO "rt1011 reset" and i2c2 initialization for RT1011.
Add CHERRY_USE_RT1011 and CHERRY_USE_RT1019 to Kconfig, so we can
spearate code for the specific codec by config.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Change-Id: I18939a2a2caae0444ce17f4712764647975121ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57157
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently clear_screen() calls set_pixel() to set all pixels. However,
the actual order of pixels being set depends on the framebuffer
orientation. With NORMAL orientation, the framebuffer is accessed
sequentially; with LEFT_UP/RIGHT_UP orientation, it is accessed back and
forth, leading to performance drop (>1 second on bugzzy).
Therefore, ensure sequential access to the framebuffer, regardless of
the orientation.
BUG=b:194967458
TEST=emerge-cherry libpayload
BRANCH=dedede
Change-Id: Iecaff5b6abc24ba4b3859cbc44c0d61b2a90b2d9
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57104
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, The SPI speed/mode configuration is split between Kconfig
and devicetree. We'd like to have everything in one place. Since we
need the fast-read speed and the mode available in the Makefile to build
the AMD EFS table, we currently need it in Kconfig. Move all of the
settings to Kconfig and remove them from Devicetree in a later commit.
BUG=b:195943311
TEST=boot majolica & guybrush, verify spi settings
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I8f29e49e886bd99b39172905e21bfd392c6c10e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56884
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add SPD support to drawcia for MT53E512M32D1NP-046 WT:B.
This part is already in global_lp4x_mem_parts.json.txt, and use
/util/spd_tool/lp4x/gen_part_id to assigns DRAM IDs.
BUG=b:196951879
BRANCH=firmware-dedede-13606.B
TEST=FW_NAME=drawcia emerge-dedede coreboot chromeos-bootimage
Change-Id: Ic42e6357943ba651ffd92fb2974e9ea52fa19020
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56905
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When modules are added to the FSP and they won't fit into the FSP binary
any more, the size can be increased in the FSP build. Especially in the
case of debug builds the increased size might not fit into the memory
region it gets decompressed into which starts at FSP_M_ADDR and has a
size of FSP_M_SIZE. SoCs can implement the soc_validate_fspm_header
function that ends up being called by the FSP driver in romstage to do
some additional checks on the FSP binary's header that includes the
version number and the image size. We can use the image size field to
check if it fits into the reserved region. Since the FSP-M memory region
is located after romstage loading it won't clobber the romstage code
where we do the check.
This runtime check is added in addition to the build-time check to also
cover the case when the FSP binaries in CBFS get replaced with ones that
don't fit into the reserved memory region after the coreboot build.
BUG=b:186149011
TEST=Mandolin still boots fine with the patch applied. When as a test
the FSP_M_SIZE Kconfig option in soc/amd/picasso is decreased to 0x10000
which is by far not enough for the decompressed FSP-M binary to fit into
it prints the newly added error message on the console and then stops.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9b74a2d03993ba50b166eb6e87d4e57b93afc069
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57068
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This CL indroduces the ELOG_RW_REGION_NAME. This constant replaced the
hardcoded "RW_ELOG" value. This constant will be used also by elogtool
(see CL in the commit chain).
BUG=b:172210863
Change-Id: Ie8d31204e65fd67d52b0f8ced7b8c1ffdcf5b539
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56986
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit moves some drivers/elog/ functionality to commonlib/bsd
since they will be called from util/cbfstool/.
In particular:
* elog_fill_timestamp(), elog_update_checksum(), elog_checksum_event()
were moved to commonlib/bsd/elog
* elog_fill_timestamp() receives the time parameters and updates the
event based on the "time" arguments.
The original elog_*() functions were written by Duncan Laurie
(see CB:1311) and he gave permission to re-license the code to BSD.
BUG=b:172210863
Change-Id: I67d5ad6e7c4d486b3d4ebb25be77998173cee5a9
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the support from the previous patch to have coreboot lock the PAM
registers instead of the FSP when the lockdown configuration is set to
coreboot.
TEST=boot to OS, read PCI 0:0.0 config register 0x80, value is 0x31
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I0c3e16edeab6f85a79eb10e1477d95952b554a18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Rename soc_validate_fsp_version to soc_validate_fspm_header, since it
can not only be used to check the version info in the FSP-M binary's
header, but also to check every other field in the binary's header. This
is a preparation for a follow-up patch that implements this function to
check the FSP-M binary's size.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ifadcfd1869bea0774dc17b69c5d1e1c241a45de1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The FSP-M binary needs to fit into the memory region that starts at
FSP_M_ADDR and is FSP_M_SIZE bytes large, so error out during build time
if the uncompressed FSP-M file is larger than the size of the region it
will be copied into.
BUG=b:186149011
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ice4a59e5a723c3c0a40b1f3f3227aee6b9dcb39a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Create the dewatt variant of the guybrush reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:196460993
BRANCH=None
TEST=util/abuild/abuild -p none -t google/guybrush -x -a
make sure the build includes GOOGLE_DEWATT
Signed-off-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Change-Id: I57860a7cad1bf202bd3ef3eed5f498fbf1d29af8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57108
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
clang seems to like to do some aggressive optimizations that break our
approach of mocking functions for test by using objcopy to turn them
weak after the fact on individual compiled object files. For example, in
CB:56601 the function cbfs_get_boot_device() is mocked this way. When
compiling the cbfs_boot_lookup() function in src/lib/cbfs.c with clang,
it will generate a normal callq instruction to a relocation for
cbfs_boot_lookup(), which can then later be pointed to the mocked
version of that function. However, it will also somehow infer that the
version of cbfs_boot_lookup() in that file can only ever return a
pointer to the static local `ro` variable (because CONFIG_VBOOT is
disabled in the environment for that particular test), and instead
generate instructions that directly load the address of a relocation for
that variable into %rdi for the following call to cbfs_lookup(), rather
than using the real function return value. (Why it would do that is
anyone's guess because this seems unlikely to be faster than just moving
the function return value from %rax into %rdi like a normal compiler.)
Long story short, this optimization breaks our tests because
cbfs_lookup() will be called with the wrong pointer. clang doesn't
provide many options to disable individual optimizations, so the only
solution seems to be to make clang aware that the function is weak
during the compilation stage already, so it can be aware that it may get
replaced. This patch implements that by marking the mocked functions
weak via #pragma weak lines in the per-test autogenerated config header.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I1f9011f444248544de7a71bbefc54edc006ae0cd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Cannon Point PCH-H does not implement the eMMC, I2C4 and I2C5 devices.
Guard the IRQ constraints for these devices to prevent FSP assertions.
Tested on Prodrive Hermes, debug FSP builds no longer fail to boot.
Change-Id: I58674d1c3c5fe4535c022020674d48d6a5315bf9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
1. According to the Maxim's comment and schematic diagram of proto, Modify I2C slave address to 0x38, 0x3c.
2. According to the schematic diagram of proto, Change GPD11 to NC.
BUG=b:191811888, b:1191213263
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ibf8adf2ed8dda9ae6da06e7e995bef9395cdee35
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57059
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Touchscreen will be no function with R93-14092.19.0 image or be later.
It just happened to work because elants_i2c driver would bind
to the device first based on "ELAN0001" HID ID
BUG=b:195994810
TEST= verify only update RW FW can fix touchscreen no function issue
1.Build test firmware
2.prepare DUT enviroment (R93 image + update RW to test firmware)
3.verify touchscreen function normally
Signed-off-by: FrankChu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Ie9e0fe726854d0128ad1bb430544640dc8f034ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Add the support RAM parts for felwinter.
Here is the ram part number list:
DRAM Part Name ID to assign
K4U6E3S4AA-MGCR 0 (0000)
K4UBE3D4AA-MGCR 1 (0001)
H9HCNNNBKMMLXR-NEE 0 (0000)
MT53E1G32D2NP-046 WT:A 2 (0010)
BUG=b:197308861
BRANCH=None
TEST=emerge-brya coreboot
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I76febefc251b02a047819242e23c02dc50891c2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Create the moonbuggy variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=191356135
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_MOONBUGGY
Signed-off-by: Rehan Ghori <rehang@google.com>
Change-Id: Iaf545dcd5ff537afdf029f510553d16a1239763e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change enables L1.1 and L1.2 on all real Guybrush PCIe devices.
BUG=b:188123142
TEST=Boot to ChromeOS and verify L1SS are functional by dumping the
settings with "lspci -vv". Leave system on for 20 minutes and no hang.
Also perform 20 reboots and suspend operations
Cq-Depend: chrome-internal:4012927
Change-Id: I40d19be78bfcb9a30fb59f48530a4413dadbefbc
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
To reduce suspend power consumption,
1. Disable unused CLKSQ2.
2. Set CLKSQ_EN to sleep control for SPM 26M sleep control.
No bus clock when enter 26m sleep control, and only control
clock square by side band.
Signed-off-by: Chun-Jie Chen <chun-jie.chen@mediatek.com>
Change-Id: Ia9a1735d6f508ce35b9af2d67831a3474255198b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57043
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
IDS (Integrated Debug Services) options are meant to be enabled when one
wants to debug AGESA. Since they are compile-time options, using Kconfig
is the logical choice. Currently, none of the options builds.
Tested with BUILD_TIMELESS=1 without adding the configuration options
into the binary, and Asus A88XM-E does not change.
Change-Id: I465627c19c9856e58ca94aa0efedbddb6baaf3f6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
The `ASSERT` macro is already defined in `src/include/assert.h`, and
AGESA's definition is never used. On Asus A88XM-E, toggling the value of
the `IDSOPT_ASSERT_ENABLED` macro does not change the resulting binary
when using reproducible builds. Attempting to use AGESA's definition of
the `ASSERT` macro results in build errors:
In file included from src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuDmi.c:56:
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuDmi.c: In function 'GetType4Type7Info':
src/vendorcode/amd/agesa/f15tn/Include/Ids.h:371:33: error: statement with no effect [-Werror=unused-value]
#define ASSERT(conditional) ((conditional) ? 0 : IdsAssert (STOP_CODE));
Given that coreboot's definition of `ASSERT` is more useful, drop
AGESA's broken definition and the useless `IDSOPT_ASSERT_ENABLED` macro.
Also remove the `IdsAssert` function, as it is no longer used anywhere.
Tested with BUILD_TIMELESS=1, Asus A88XM-E remains identical.
Change-Id: Ia4e5dbfd3d2e5cec979b8b16fbc11d1ca8a0661e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
In preparation to replace OptionsIds.h with Kconfig options, use the
same settings on all AGESA f15tn boards. The only difference this makes
is that the `IDS_LATE_RUN_AP_TASK` macro no longer expands to nothing.
It is expected that the impact this difference makes is minimal.
Note that the `IDSOPT_TRACING_ENABLED` option currently fails to build.
Tested on asus/f2a85-m, still boots.
Change-Id: Iedd4d1f255650012f3efd9a27718e18c1c904dc1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53982
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch changes the sc7180 boards to use the new common MIPI panel
framework, which allows more flexible initialization command packing and
sharing panel definitions between boards. (I'm taking the lane count
control back out again for now, since it seems we only ever want 4 for
now anyway, and if we ever have a need for a different lane count it's
not clear whether that should be a property of the board or the panel or
both. Better to leave that decision until we have a real use case.)
Also, the code was not written to deal with DCS commands that were not a
length divisible by 4 (it would read over the end of the command
buffer). The corresponding kernel driver seems to pad the command with
0xff instead, let's do the same here. (Also increase the maximum allowed
command length to 256 bytes, as per Qualcomm's recommendation.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I78f6efbaa9da88a3574d5c6a51061e308412340e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56966
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
An MST hub is only present on some devices that are configured with a
particular daughterboard indicated by EC fw_config, so add a fw_config
probe that matches the USB daughterboard ID from CBI to only enable it
on devices where present, using variant-specific daughterboard IDs.
BUG=b:185862297
TEST=RTD2141 remains in ACPI tables on a berknip with Dali DB, and is
not present on the same system if probe is changed to enable it
for picasso DB.
BRANCH=zork
Change-Id: I4ada9b492ab221fa98350bf2faf27a23342f3a55
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
PSP_Verstage will take almost the entire time to run that
is allotted to S0i3 resume. Since coreboot isn't running,
the PSP needs to handle any security requirements. The long-
term plan is that the PSP won't even load psp_verstage on S0i3
resume, but when it is loaded, this makes sure we exit
immediately
BUG=b:177064859
TEST=Verify that PSP_verstage doesn't run on S0i3 resume
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ia7b2560ff3d7621922ec4bc0e8793961f5d7550f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This reverts commit 66dbb0c5d6.
The numbers were meant for Cannon Lake, but the code was also meant
to be used for all other platforms using the Cannon Point PCH. Now
Cannon Lake support is even dropped, so we can cleanly revert to the
recommended values for the other platforms.
Change-Id: Iea56c6a29ca4b34c9852393fed2e3be4de128ec6
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56662
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to received feedback, FSP-T enables MMCONF at address
0xe0000000 with 256 busses. Sanity-check that Kconfig matches that.
Add MMCONF_BUS_NUMBER such that MCFG in ACPI will be correct.
Change-Id: I01309638a9f4ada71e5e3789db34892ed4abfa3b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch enables eNEM flow for Alder Lake SoC hence drop INTEL_CAR_NEM
Kconfig from ADL-P RVP. ALDERLAKE_CAR_ENHANCED_NEM Kconfig will select all
relevant Kconfig required to enable eNEM for Alder Lake.
Additionally, select INTEL_CAR_NEM Kconfig for ADL-M RVPs from Kconfig.name.
BUG=b:168820083
TEST=Able to build and boot ADL-P RVP using eNEM mode.
Change-Id: I08561c8f50bbc4afe2bcdff4cc50e74d8fa2f68e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48345
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch decouples the selection of eNEM feature enablement from SoC
to ensure the ADLRVP does the validation first prior enabling this
feature on OEM/ODM reference designs.
BUG=b:168820083
TEST=No changing is being observed in .config with and without this CL.
Change-Id: I709185159d9869501b1d8e8d00f6d25ec77838bf
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
There are gremlins in the system. thread_coop_enable has an assert. This
is currently problematic for two reasons.
assert(current->can_yield <= 0);
When doing smm_do_relocate we are entering a deadlock. The root cause
hasn't been quite found yet, but it's related to co-op multi-threading.
For some reason the assert in thread_coop_enable is firing when
releasing the console_lock spin lock. I'm assuming cpu_info hasn't been
initialized yet. The assert tries to perform a printk, but since the
console_lock is still held we end up in a dead lock. This dead lock will
generally not happen after a warm reset. Again I'm assuming because the
cpu_info struct has some valid values at this point.
For now disable multi-tasking until we fix the cpu_info initialization.
BUG=b:194391185
TEST=Boot guybrush to OS
Co-developed-by: nikolai.vyssotski@amd.corp-partner.google.com
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia3143f538a31b5aaaea104aa1d8bcf44e6dcb528
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57005
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update the `_HID` value of device in SSDT depending on the fw_config.
According to value of AUDIO_CODEC_SOURCE field in fw_config(SSFC) which
stored in CBI:
AUDIO_CODEC_ALC5682: _HID = "10EC5682" /* ALC5682I-VD */
AUDIO_CODEC_ALC5682I_VS: _HID = "RTL5682" /* ALC5682I-VS */
BUG=b:193623380
BRANCH=dedede
TEST=ALC5682I-VD or VS audio codec can work normally
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: Ic8840454e4934162ea59c742634a56f70b153238
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
All boards that are trying to use MIPI panels eventually run into the
problem that they need to store physical parameters and a list of DCS
initialization commands for each panel, and these commands can be very
different (e.g. a large amount of very short commands, a few very large
commands, etc.). Finding a data format to fit all these different cases
efficiently into the same structures keeps being a challenge, and the
Kukui mainboard already once put a lot of effort into designing a
clean, flexible and efficient solution for this. This patch moves that
framework into a common src/device/mipi/ library where it can be used by
other boards as well. (Also, this will hopefully allow us to save some
duplicated work when using the same panel on different boards at some
point.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I877f2b0c7ab984412b288e2ed27f37cd93c70863
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The change from Synaptics S7817 to Elan 3915N and pin distribution
of touch IC is the same.
The original Elan section was copied from reference design and
was never used before.
According to vendor spec definition IRQ trigger method needs to
change to level.
BUG=b:190574692
TEST=Build coreboot and check that device works
Change-Id: I44ee779242779c78ceafdddd34dca2571e714dd3
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56380
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adds the ability to output MSRs dump for the specified range of CPU
cores. This makes it easier to reverse engineer server multicore
processors using the inteltool utility.
The range is set using --cpu-range <start>[-<end>] command line option:
$ sudo ./inteltool -M --cpu-range 0-7
$ sudo ./inteltool -M --cpu-range 7-15
$ sudo ./inteltool -M --cpu-range 32
$ sudo ./inteltool -M will print a register dump for all cores, just
as before.
Change-Id: I3a037cf7ac270d2b51d6e453334c358ff47b4105
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35919
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
"Latched" GPIOs like this one are a virtual representation of the
pending interrupt flag for the edge-triggered pin and not a direct
representation of line state, so they should always be marked
ACTIVE_HIGH or depthcharge will incorrectly negate them. This has always
been wrong and meant that depthcharge doesn't correctly wait for Cr50
flow control responses on these platforms. Thankfully it doesn't seem
like we've seen any practical issues from this, but it's still very
wrong.
BRANCH=trogdor
BUG=none
TEST=Booted CoachZ (no visible difference)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie1586b0e10b64df0712e28552411c4d540a7e457
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Setting the clock source depends on clock request pin for WLAN/SD/SSD device. Also turn off the unused (4/5/6) clock sources.
In guybrush, clock source 0/1/2/3 are routed for WLAN/SD/WWAN/SSD device.
BUG=b:186384256
BRANCH=none
TEST=Verify the config setting can update to the GPPCLKCONTROL registers.
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Change-Id: I240543e92cbc178cee034c37d7c26da0a6bbb7f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56895
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I20bf1a87c7a9b343a86053692617c127a1a3250d
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56955
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: I175ae26f934f08e125bea7cc3195bdb5792c2360
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56954
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the driblee variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:191732473
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_DRIBLEE
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I1ad9a4e0cf7999337b55d62d5cc94e4f6c2e98f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Create the corori variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:194356176
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CORORI
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I8380d5aab61c99d545625789ff1251ec1caa84a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56796
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All Atlas devices have the touchscreen controller, so probing for its
presence is unnecessary. Removing the probe requirement allows the
touchscreen ACPI device in Linux to re-enumerate when rebinding its
I2C adapter device.
Without this change, after rebinding the touchscreen's I2C adapter
device using sysfs the touchscreen ACPI and HID devices are absent, and
the touchscreen is unresponsive.
With this change, the touchscreen ACPI and HID devices are re-created
after rebinding its I2C adapter device, and the touchscreen becomes
responsive again.
BUG=b:177350937
TEST=Tested on 2 Atlas DUTs running Chrome OS R94 top-of-tree builds
with Linux 4.4 and 5.4.
Built new AP FW from Atlas Chrome OS firmware branch with this change
applied. Tested shipping RO + new RW, and new RO + new RW.
Test sequence:
1) Boot DUT, verify basic touchscreen functionality.
2) $ cd /sys/bus/platform/drivers/i2c_designware
3) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00{,/0018:0483:1058.*{,/hidraw{,/hidraw*}}}}}
lrwxrwxrwx. 1 root root 0 Aug 12 01:07 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 5 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6
drwxr-xr-x. 4 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00
drwxr-xr-x. 5 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002
drwxr-xr-x. 3 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002/hidraw
drwxr-xr-x. 3 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002/hidraw/hidraw1
4) $ echo i2c_designware.0 > unbind
5) Verify touchscreen is unresponsive (as expected after unbind).
6) $ ls -ld i2c_designware.0
ls: cannot access 'i2c_designware.0': No such file or directory
7) $ echo i2c_designware.0 > bind
*** Without this change: ***
8) Touchscreen remains unresponsive.
9) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00}}
ls: cannot access 'i2c_designware.0/i2c-6/i2c-ACPI0C50:00': No such file or directory
lrwxrwxrwx. 1 root root 0 Aug 12 01:18 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 4 root root 0 Aug 12 01:18 i2c_designware.0/i2c-6
*** With this change: ***
8) Touchscreen is functional again.
9) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00{,/0018:0483:1058.*{,/hidraw{,/hidraw*}}}}}
lrwxrwxrwx. 1 root root 0 Aug 12 01:09 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 5 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6
drwxr-xr-x. 4 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00
drwxr-xr-x. 5 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003
drwxr-xr-x. 3 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003/hidraw
drwxr-xr-x. 3 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003/hidraw/hidraw1
Signed-off-by: Matthew Blecker <matthewb@chromium.org>
Change-Id: I7b90690b0591e8748d7a007f8cc9688d393e59db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56928
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Recent change "7a8c68a: mb/google/brya: Configure H21 as GPO and A17
as low" turned EN_FCAM_PWR low since EN_FCAM_PWR is turned ON and
OFF by IPU driver while MIPI UFC probing. However USB UFC also
requires 3.3V which is enabled by A17. This caused USB UFC
enumeration to fail
BUG=b:196014678
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I88c204ec07b1f7511f0d88074e336cfc9116a7d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56882
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable MKBP (Matrix Keyboard Protocol) interface for all Brya family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:170966461
TEST=manual test on Brya P1: Volume Up/Down buttons
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: Ic9c707f57871f388c363e01c9ab78a3b358ce728
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Versions of expat before 2.4.0 have been renamed to prevent their
use, due to some kind of vulnerability. without updating this
dependency it is currently not possible to build crossgcc with GDB.
Change-Id: Iec2cf560902dc556a41206d7dcd65c22cf3e1215
Signed-off-by: Mackenzie May <ky0ko@disroot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56868
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Alder Lake SoC specific Kconfig that internally selects all eNEM
related Kconfig. CONFIG_ALDERLAKE_CAR_ENHANCED_NEM will get
autoselected if platform doesn't have INTEL_CAR_NEM Kconfig selected
explicitly.
BUG=b:168820083
TEST=Verified CONFIG_INTEL_CAR_NEM is still enable.
Change-Id: Ife1c7d2036cece4598275dfc26ed138fb46bd881
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56090
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Alder Lake onwards IA SoC to select CAR_HAS_L3_PROTECTED_WAYS from SoC
Kconfig and here is modified flow as below:
Add new MSR 0xc85 IA32_L3_PROTECTED_WAYS
Update eNEM init flow:
- Set MSR 0xC85 L3_Protected_ways = (1 << data ways) - 1
Update eNEM teardown flow:
- Set MSR 0xC85 L3_Protected_ways = 0x00000
BUG=b:168820083
TEST=Verified filling up the entire cache with memcpy at the beginning
itself and then running the entire bootblock, verstage, debug FSP-M
without running into any issue. This proves that code caching and
eviction is working as expected in eNEM mode.
Change-Id: Idb5a9ec74c50bda371c30e13aeadbb4326887fd6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
MSR IA_SF_QOS_INFO (0xc87) has been introduced since TGL and is used
to find out the NUM_SNOOP_FILTER_WAYS. Bit[5:0] of MSR 0xc87 indicates
the maximum number of bits that may be set in any of the SF MASK
register. Hence, this patch calculates SF way count using below logic:
Calculate SF masks 1:
1. Calculate SFWayCnt = (MSR 0xC87) & 0x3f
2. if CONFIG_SF_MASK_2WAYS_PER_BIT:
a. SFWayCnt = SFWayCnt / 2
3. Set SF_MASK_1 = ((1 << SFWayCnt) - 1) - SF_MASK_2
Change-Id: Ifd0b7e1a90cad4a4837adf6067fe8301dcd0a941
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
As per TGL EDS, two ways will be controlled with one bit of SF QoS
register hence, this patch introduces SF_MASK_2WAYS_PER_BIT Kconfig to
allow SoC users to select SF_MASK_2WAYS_PER_BIT to follow the EDS
recommendation.
Calculate SF masks 2:
1. if CONFIG_SF_MASK_2WAYS_PER_BIT:
a. data_ways = data_ways / 2
Also, program SF Mask#2 using below logic:
2. Set SF_MASK_2 = (1 << data_ways) - 1
Change-Id: I442bed75f13d26f357cfb32c54c5fe9efa4b474b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Set PL4 value dynamically for brya board based on CPU SKUs
which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000) PL4 (100000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000) PL4 (105000)
Change-Id: I20b98ccd8493ed238de647cda8ceb25f62029133
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Create the nipperkin variant of the guybrush reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/guybrush -x -a
make sure the build includes GOOGLE_NIPPERKIN
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ie525ea501e6c3d5d94e67c1db1d4e307fb7ccba7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56921
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Hook up microcode from 3rdparty repo for:
- TGL-U: 06-8c-01 (CPUID signature: 0x806c1)
- TGL-R: 06-8c-02 (CPUID signature: 0x806c2)
Verified microcode blob was found in CBFS on system76/darp7 (TGL-U).
CBFS: Found 'cpu_microcode_blob.bin' @0x103c0 size 0x31c00 in mcache @0x76c2d0ac
microcode: sig=0x806c1 pf=0x80 revision=0x88
coreboot reports the correct revision for the microcode.
Change-Id: I210c0133dad7ade63b9f7177aaa9a69b019469af
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56862
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update submodule pointer to include microcode for TGL and others.
Tested the following still boot:
- galp3-c (WHL-U): sig=0x806eb pf=0x80 revision=0xe9
- oryp5 (CFL-H): sig=0x906ea pf=0x20 revision=0xe9
- gaze15 (CML-H): sig=0xa0652 pf=0x20 revision=0xe9
coreboot reports the revision as -1 from what it actually is. i.e.,
these should report revision=0xea (and that is what Linux reports).
However, this behavior is not new.
Change-Id: I084ba67e8eaf7383f1c05fa5589b63c92ff900b1
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56861
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable MKBP (Matrix Keyboard Protocol) interface for all dedede family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:170966461
TEST=manual test on Madoo:
Volume Up/Down and Power buttons, Tablet Mode switch
Cq-Depend: chromium:3069163
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: I9d1f43e4dd56318af4c1d5f5c1c3a2c237a05c5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56840
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With current setting Display audio codec probe fails.
Hence HDMI/DP audio fails.
Earlier, with FSP 2037 was used the mode was incorrectly programmed to 4T
This setting was carried ahead with below change:
Commit : 50f8b4ebdd
The issue was fixed in later FSPs and with current
FSP v2237, we need to set the TMODE to 8T as per spec.
TEST=Verify HDMI/DP Playback on ADL P RVP
Fixes: 50f8b4ebdd
(soc/intel/alderlake: Add enum for HDA audio configuration)
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Change-Id: Ia39a33f5da2fea0dc2eaf4eae45999a711c61c33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56208
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Balaji Manigandan <balaji.manigandan@intel.com>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-clause and adjust comments.
This changes behavior since now related options are always set,
depending on if coreboot or the FSP should be responsible for the
chipset lockdown. This ensures a defined state independent from the
default configuration of the FSP.
Change-Id: I0c43a11a40a474de4af22aa5506b1d387809bda2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause and adjust comments.
Change-Id: I202c212ec8e9ac63f5512c2e74040c23e1562b9a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This patch updates the VccIn Aux Imon IccMax for ADL-P to SOC SKU
specific values from the FSP default value 160.
* ADL-P 682(45W) = 137.
* ADL-P 482(28W) = 128.
* ADL-P 282(15W) = 128.
These config values are generated iPDG application with ADL-P platform
package tool and supports 15W/28W/45W SKU's.
RDC Kit ID for the iPDG tools,
* Intel(R) Platform Design Studio Installer: 610905.
* Intel(R) Platform Design Studio - Platform ADL-P (Partial): 627345.
* Intel(R) Platform Design Studio - Platform ADL-P (Full): 630261.
BUG=b:195033556
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I6c159035cba781d3661a0a0cef16f9591a583912
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56176
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Originally we use rank_density=0 to mean disable the channel, but actually
rank_density=0 means 4Gb density in the FSP.
This patch changes the LPDDR4 enum values to the real density number and
adds a switch statement to mapping the density define in the FSP.
BUG=b:178665760
BRANCH=NONE
TEST=build fw and flash to the dut, the dut can boot up successfully.
Change-Id: I36dba2cef130211e7aea9e2a4f82c5db78f82a83
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56805
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
System76 uses several custom CMOS values downstream. Reduce our diff by
providing a generic layout with the defaults:
boot_option=Fallback
debug_level=Debug
power_on_after_fail=Enable
Tested on galp3-c, gaze15, oryp5, oryp6. All boards boot multiple times
with USE_OPTION_TABLE selected.
Change-Id: Ie57b0e5713bba8ad46e1a4123a3ddd43e0eea964
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Prevent the FSP from writing its default SVID SDID values of 8086:7270
for internal devices as this locks most of the registers. Allows the
subsystemid values set in devicetree to be used.
A description of this SSID table override behavior, along with example
code, is provided in the TigerLake FSP Integration Guide, section
15.178 ("SI_CONFIG Struct Reference").
The xHCI and HDA devices have RW/L registers rather than RW/O registers.
They can be written to multiple times but cannot be modified after
being locked, which happens during FspSiliconInit. Because coreboot
populates subsystem IDs after SiliconInit, these devices specifically
must be written beforehand or will otherwise be locked with their
default values of 0:0.
TGL also introduces parameters for customizing the default SVID:SSID.
These must be set or it will still use the FSP defaults.
Tested by checking lspci output on System76 darp7 (TGL-U).
References:
- b1fa231d76 ("soc/intel/cnl: Allow setting PCIe subsystem IDs after FSP-S")
- TigerLake FSP Integration Guide
- Intel Document #631120-001
Change-Id: I391b9fd0dc9dda925c1c8fe52bff153fe044d73e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Make use of deterministic cache helper functions from Alder Lake
SoC code to print useful information during boot as below:
Cache: Level 3: Associativity = 12 Partitions = 1 Line Size=64 Sets=16384
Cache size = 12 MiB
Change-Id: I30a56266015d69abccb885b3f230689488ee0360
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch creates helper function that internally detects the CPU
type (AMD or Intel) and pick the leaf to send CPUID instruction with
different cache level to retrieve deterministic cache parameters.
Lists of helper functions generated as part of this CL :
1. cpu_check_deterministic_cache_cpuid_supported => if CPU has support
for deterministic cache using CPUID instruction.
2. cpu_get_cache_ways_assoc_info => Get cache ways for associativity.
3. cpu_get_cache_type => Get cache type.
4. cpu_get_cache_level => Get cache level.
5. cpu_get_cache_phy_partition_info => Get cache physical partitions.
6. cpu_get_cache_line_size => Get cache line size.
7. cpu_get_cache_sets => Get cache number of sets.
8. cpu_is_cache_full_assoc => Check if cache is fully associative.
9. cpu_get_max_cache_share => Cores are sharing this cache.
10. get_cache_size => Calculate the cache size.
11. fill_cpu_cache_info => Fill cpu_cache_info structure.
Change-Id: I0dd701fb47460092448b64c7fa2162f762bf3095
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
TSR2 thermal sensor doesn't define in cret. Fix DPTF passive and
critical policies for getting negative temperatures in OS.
BUG=b:195868075
BRANCH=dedede
TEST=Build and boot to OS in cret. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I849662cbb3adc8e528d65af2c90e7c8e4880d607
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I8f7c3184b62f8d84ca4605fb9f2a1cc569f1f964
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56853
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: Ibc60494b0032a3139c1e6c79251fb2da750c8de8
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Keep the clock source for PCIe slots as always on. Also turn off the
unused (0/1/5/6) clock sources. Currently bilby only uses clock sources
2, 3 and 4, out of which clock source 3 and 4 are routed for PCIe
external slot. And clock source 2 is routed for M.2 PCIe slot.
TEST:Verify end devices enumerate on D:F 1.1/1.2 RPs over warm reboot.
Signed-off-by: Aamir Bohra <aamirbohra@gmail.com>
Change-Id: Ida485b06279b0a8659c8d00873c3d6023d1e542f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56826
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch extends mocks functionality to allowing wrapping of mocked
functions. Original function name will be prefixed with `__real_`.
Example:
- Mocked function: cbfs_lookup()
- New function name: __real_cbfs_lookup()
- Mock name: cbfs_lookup()
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I7cd0d66a17029955cbf75c8b155a7ebb7f5513aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56719
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set power limits for brya0 variant board based on CPU SKUs
which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 variant board with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000)
Change-Id: I4c07319af756b10e5d22f320e97ff956fb4a14c6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56622
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to support wake from D3cold, most devices require extra
circuitry and possibly out-of-band communications to the host.
Therefore, assume that most UARTs that do have wake capabilities support
wake from D3hot rather than D3cold.
BUG=b:187228954
TEST=compile
Change-Id: I24d6d0e81d980fc9c910d8f47f557c88990b6400
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In order to support wake from D3cold, most devices require extra
circuitry and possibly out-of-band communications to the host.
Therefore, assume that most SPI peripherals that do have wake
capabilities support wake from D3hot rather than D3cold.
This also allows coreboot to expose a power resource to perform power
sequencing for a SPI peripheral that is intended to retain power in
S3/S0ix.
If support for a device with d3cold wake support is needed, it could be
added in later as an option.
BUG=b:187228954
TEST=compile
Change-Id: I1d739b49c1a43007eb0199fe39b3b7d7375e6577
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add dynamic power limits selection mechanism for brya board based on
CPU SKUs which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000)
Change-Id: I86619516adeec13642f02ba7faf9fc4945ad774e
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: I726d70b4ffc35a28a654abbd20c866f1410e1aee
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
coreboot always assumes that BSP APIC ID will always be 0 but as
per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, it says that BSP can
be any processor whose index/APIC ID might not be 0.
To handle this situation, init_cpu call is required to modify to
handle dynamic detection of APIC ID from BSP instead of hardcoding
always through devicetree. Function has been updated to create
a new node with actual BSP APIC ID when devicetree doesn't contain
APIC ID defined. In case APID ID is defined, function will use a
node with the APIC ID defined in devicetree.
Changes also requires to remove "lapic 0" hardcoding from devicetree
to allow code to fill BSP APIC ID dynamically. Otherwise coreboot
will create an extra node for CPU with APIC ID 0 and it'll show as a
extra node in kernel. This will cause kernel to report wrong (extra)
core count information then actually present.
BUG=None
BRANCH=None
TEST=Boot the JSL system and observe there is no functional impacts.
Without this CL kernel core count in `lscpu` = 3
With this CL, kernel core count is corrected to 2.
Change-Id: Ib14a5c31b3afb0d773284c684bd1994a78b94445
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Lulu is the only variant that does not disable channel 1 in pei_data
when the SPD index indicates it is unused. For consistency with the
other variants that use SPD files, disable channel 1 explicitly.
Change-Id: I8c613c5d90075495d2f76d33abf15d74ac63c125
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55802
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Chromebook have some platform need support MICMUTE and KBDILLUMTOGGLE.
- Sync ec_commands.h
This change syncs the coreboot version of google ec_commands.h with the
ec_commands.h from the google ec repository. This is a straight copy
except for the the copyright header.
BUG=b:194146863
BRANCH=none
TEST=check on evtest
type 4 (EV_MSC), code 4 (MSC_SCAN), value 9e
type 1 (EV_KEY), code 228 (KEY_KBDILLUMTOGGLE), 1
type 4 (EV_MSC), code 4 (MSC_SCAN), value 9b
type 1 (EV_KEY), code 248 (KEY_MICMUTE), value 1
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: Ie4fa3e627f448265f72279704d258b2d3fe8fc17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56710
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Even though pkg-config might be installed, it might or will not return
true in the checks whether 'PKG' or 'PKG2' is installed.
Extend the script to look in another location for ncurses.h
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: I4344ba2116c0b8618357db4248d993509cbb666e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
DFD (Design for Debug) is a debugging tool, which scans
flip-flops and dumps to internal RAM on the WDT reset.
After system reboots, those values could be showed for
debugging.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I39a4391c1d1e832d77b709f8f899bb1c6dcacd69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add a new Kconfig option to enable or disable the 4 DWORD burst support
of the SPI controller and use this setting to determine if the
corresponding feature bit in SPI100_HOST_PREF_CONFIG will be set or
cleared. Since fch_spi_disable_4dw_burst can now enable or disable the
feature, rename it to fch_spi_configure_4dw_burst. On Stoneyridge the
SPI_RD4DW_EN_HOST bit needs to be cleared (see the Rd4dw_en_host bit
definition in the SPIx2C SPI100 Host Prefetch Config register in the
public BKDG #55072 Rev 3.09), so add a SoC dependency to the Kconfig
option.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id754fa8d5f9554ed25cf9f3341bfdd1968693788
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Add a new tool that that prints elog events.
The tool, as input, accepts either a file with the RW_ELOG contents, or
if the file is not provided it reads the contents of RW_ELOG by calling
the "flashrom" tool.
The tool is based on "mosys eventlog list"[1]. For the moment it only
supports "list", but future commits will add additional functionality.
This commit also adds missing ELOG defines needed for the tool. These
defines are added with the rest of the ELOG defines, in
include/commonlib/bsd/elog.h
The tool is placed inside util/cbfstool. The rationale behind the
decision, is that this tool shares a lot in common with the other tools
located in cbfstool: vboot dependency, shared files like common.o and
valstr.o, and in spirit is similar to some of the tools located in
cbfstool/.
As an example, you call the tool like the following:
$ elogtool list -f rw_elog_dump.bin
[1]: https://chromium.googlesource.com/chromiumos/platform/mosys/+/refs/heads/main/lib/eventlog/elog.c
BUG=b:172210863
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Change-Id: Ia1fe1c9ed3c4c6bda846055d4b10943b54463935
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Move ELOG defines and structs from include/elog.h to
include/comonlib/bsd/elog.h.
This is needed because the will be used from util/
(in a future commit).
It also replaces uNN types with uintNN_t types, for the reason described
above.
BUG=b:172210863
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Change-Id: I4f307f599a311810df2367b7c888f650cff1214a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Gimble don't have retimer on port0, the port need to be configured for the SOC to handle Aux orientation flipping.
Also add "typec_aux_bias_pads" lets the SoC IOM firmware control the Aux DC bias voltages.
BUG=b:195087071
BRANCH=none
TEST=check both orientation can output display on type-c monitor.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I057048c14110bb81bf5b5fd0e3151deb031ca5d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Create the bugzzy variant of the waddledoo reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:192521391
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_BUGZZY
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Change-Id: I851b9a75c387586d2fb84b762788e962f33472b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add current maintainers for vboot-related code, and combine the vboot
and vboot2 sections which are not really separate anymore. What's left
in vendorcode/google/chromeos isn't really related to vboot anymore
since the vboot code was moved under src/security, so take it out of
there.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I59a2df9c1580291a6d29537868aab0e1b339a2ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56728
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The all shipped magolor and maglia has SSFC= 0x840.
The value is defined as 5M MIPI camera.But the value:0x840 will
conflict with the updated touchscreen field.
It will cause some touchscreen no function if make auto-update new
firmware.The CL would correct the field error.
The original fields:
CAMERA_WFC 38 40
TS_SOURCE 41 44
Correct fields:
MIPI Cam
CAMERA_WFC 38 40
CAMERA_UFC 41 42
CAMERA_VCM 43 44
Touch-screen
TS_SOURCE 45 48
The SSFC value of Magolor:
CAMERA_OVTI5675 5M AF (SSFC = 0x840)
CAMERA_OVTI8856 8M AF (SSFC = 0x880)
BUG=b:194639170
TEST=Build firmware and verify on camera and touch-screen devices
Change-Id: I13d76ce8b932f483e20ca5388f1c67eb39ba12a1
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56685
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
DDI 0/1 ports are shared for DP and HDMI. This implementation
adds support for HDMI display when HDMI is set as connector type
in ddi descriptors.
TEST=verify display over HDMI(0 and 1) in OS.
Signed-off-by: Aamir Bohra <aamirbohra@gmail.com>
Change-Id: I9697211c556f12d1fc0d49418b227fbe6b342673
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Move elog_internal.h to commonlib/bsd/include/bsd/.
And rename it from elog_internal.h to elog.h.
Since this file will be included from util/ it also converts the "uNN"
types into "uintNN_t" types.
The two defines that are not used by util/ are moved to
drivers/elog/elog.c, the only file that includes them.
Move also the function elog_verify_header() from drivers/elog/, to
commonlib/bsd/elog.c since this function will be called from util/
as well.
The rationale behind moving elog's defines & structs to
commonlib/bsd/include is to make them available to util/ tools and/or
payloads (should it be needed in the future).
The files that are being relicensed to BSD were coded by Duncan Laurie,
and he is Ok with the relicense.
BUG=b:172210863
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Change-Id: Ia1aefea705ddd417a1d9e978bb18ab6d9a60cad6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Move post_codes.h from include/console to
commonlib/include/commonlib/console.
This is because post_codes.h is needed by code from util/
(util/ code in different commit).
Also, it sorts the #include statements in the files that were
modified.
BUG=b:172210863
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Change-Id: Ie48c4b1d01474237d007c47832613cf1d4a86ae1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56403
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sometimes it's preferable or even necessary (e.g. stability issues) to
limit the maximum package C state. Let's add a devicetree option that
keeps the current behavior if it is left unset.
Change-Id: I0dc254d34f46de4c65cb85cc92e4b7f26618888d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add basic devapc (device access permission control) drivers.
DAPC driver is used to set up bus fabric security and data protection
among hardwares. DAPC driver groups the master hardwares into different
domains and gives secure and non-secure property. The slave hardware can
configure different access permissions for different domains via DAPC
driver.
1. Initialize devapc.
2. Set master domain and secure side band.
3. Set domain remap.
4. Set default permission.
Change-Id: I3677657a117caed0d73526f78b0ebe8180148335
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Enable the PCIe RTD3 driver for WWAN device attached to PCIe Root
Port 6 and provide the reset GPIO / src clk pins.
BUG=None
BRANCH=None
TEST=Build and boot the coreboot image, check if device is enumerated
in the lspci list after warm/cold reboot cycles, run suspend cycles and
check if WWAN is entering L2 LPM.
Signed-off-by: Thejaswani Putta <thejaswani.putta@intel.com>
Change-Id: Ie9d1ce55cc1297ea0e1069979bbecfaac8f8de05
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
- configure TROGDOR_HAS_MIPI_PANEL to "n" by default, it can be updated for mipi panels.
- add simple rm69299 panel as an example to append new mipi panels.
- use existing edid struct to update mipi panel parameters.
- add dsi command tx interface for mipi panel on commands.
Change-Id: Id698265a4e2399ad1c26e026e9a5f8ecd305467f
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52662
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, the `USE_LEGACY_8254_TIMER` Kconfig option is the only way
to enable or disable the legacy 8254 timer. Add the `legacy_8254_timer`
CMOS option to allow enabling and disabling the 8254 timer without
having to rebuild and reflash coreboot. If options are not enabled or
the option is missing in cmos.layout, the Kconfig setting is used.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ic82c7f25cdf6587de5c40f59441579cfc92ff2f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Crashlog is a debug feature and not used in normal mode of operation.
Disabling this feature will allow us to disable unused IPs and also
provide boot time savings of ~5-7 ms.
BUG=b:195327879
BRANCH=None
TEST=Platform boots and no function impact
Change-Id: I1f7def4ea41ff7a566aada080be1e791c11766e6
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56654
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This file only contains the `broadwell_run_reference_code()` function
prototype (either a declaration or an inline stub definition). Rename
this file to refcode.h and only include it where necessary.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I6513f45b8914a84312b27ef4860870a89fd0aab3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55582
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update tianocore branch used with default UEFIPAYLOAD option to
mrchromebox/uefipayload_202107 (July 2021) branch. This branch is
rebased on edk2 upstream commit 12e34cd2f7900578ee83cb01b8f1696a7bb7511b
[OvmfPkg/Bhyve: clean up TPM_ENABLE remnants] vs tag edk2-stable202105.
The main changes are fixes for e820 table parsing and support to disable
"Above 4G decode", which is required to boot distros with bootloaders
that expect to be loaded into RAM below 4G. This fixes booting with
Qubes, ZorinOS, Proxmox, among others.
Additionally, several commits on top of upstream have been consolidated,
reworked, and/or reordered for readability and maintainability.
Change-Id: I6f04fd027a0599ca6892a1376938108a2e402ac2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Some legacy devices need to have the master bit set in the PCI config
due to old drivers not setting it correctly. Set the master bit if the
feature is enabled via Kconfig switch PCI_ALLOW_BUS_MASTER_ANY_DEVICE.
For now, the PCI devices with the ID 110a:403e and 110a:403f needs this
master bit to be set.
Change-Id: Id3f6bda97e5f47d0613a1db8f8adac0b158ab8b1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56632
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Boards based on mc_ehl have, just like some mc_apl variants, legacy
devices on the PCI bus which take longer to boot. In order to ensure
that they will be enumerated correctly wait for them to come up before
PCI scan starts.
TEST=Checked that the new message is visible in the log.
Change-Id: If2f935b69ddaa9364566deacfada5e7d41fcdabd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56631
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GENMASK is defined in multiple files (with various names such as
MASKBIT), which sets certain consecutive bits to 1 and leaves the others
to 0. To avoid duplicate macros, add GENMASK macro to helpers.h.
GENMASK(high, low) sets bits from `high` to `low` (inclusive) to 1. For
example, GENMASK(39, 21) gives us the 64-bit vector 0x000000ffffe00000.
Remove duplicate macro definitions. Also utilize GENMASK for _BF_MASK in
mmio.h.
BUG=none
TEST=make tests/commonlib/bsd/helpers-test
TEST=emerge-cherry coreboot
BRANCH=none
Change-Id: If2e7c4827d8a7d27688534593b556a72f16f0c2b
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
As per the schematics, UFC has on card oscillator so we donot need
H21 in NF1 that is IMGCLKOUT
H21 is used to enable this oscialltor so configuring it as 1
A17 is configured as high while _ON method is called by driver and
it is configured as low when _OFF method is called by driver.
Hence coreboot should configure it as low on boot.
BUG=b:190674542
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I745169a5ab6a9c20b6e1bda792a43193d04ac48d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56655
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Chromebook have some platform need support MICMUTE and KBDILLUMTOGGLE.
BUG=b:194146863
BRANCH=none
TEST=check on evtest
type 4 (EV_MSC), code 4 (MSC_SCAN), value ab
type 1 (EV_KEY), code 228 (KEY_KBDILLUMTOGGLE), 1
type 4 (EV_MSC), code 4 (MSC_SCAN), value 9b
type 1 (EV_KEY), code 248 (KEY_MICMUTE), value 1
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: Ic39ecb3118e885c9e6d84d7b78bf435cb903d17e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
LTE module L850-GL may encounter U3 wakeup race condition with the host.
Setting xHCI LFPS periodic sampling off time to 0ms so that the host would not
miss the device-initiated U3 wakeup thus avoid the race condition.
BUG=b:187801363
BRANCH=dedede
TEST=flash the image to the device. Run following command to check the bits[7:4] is 0x0:
iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: stanley.wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I9328e758ed92389e44b25ff4daf6ec19b37ae7d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ben Kao <ben.kao@intel.corp-partner.google.com>
A valid GEVENT number is never negative. The local variable in
set_single_gpio still needs to be a signed integer, since the return
value of get_gpio_gevent being -1 indicates that the GPIO can't generate
a GEVENT. The check for that makes the function return before calling
program_smi of program_sci, so the parameter of those functions can be
changed to unsigned.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6ce23ceed1585589932824b8cab2a138328672a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56705
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Each bit in the GPIO wake status index registers is set to 1 when at
least one of 4 corresponding GPIO pins has its wake status register set.
Added the comment since the gpio_base + i * 4 in the next line looked as
if it calculates some absolute register value which is not what the code
does or should be doing.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2fc8e9c5bd7c1b011f364b05d0cfdeb0df88ada6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56703
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Realtek speaker amplifiers under auto mode operation have Absolute Max
Rating (AMR) at 1.98 V. Hence probe the firmware config for speaker
amplifier and program the VCCIOSEL accordingly.
BUG=b:194120188
TEST=Build and boot to OS in Storo. Ensure that the VCCIO selection is
configured as expected and probing the GPIO reads the configured
voltage.
Change-Id: Ibd3bc90bd0bbc9a35922b29e3d1e106321bc7a06
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56616
Reviewed-by: Evan Green <evgreen@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
L1 substates of a PCIe link are meant to save some power when the link
is not active but have the drawback that the PCIe latency is increased
as PLLs are switched on and off as needed.
In order to get a better realtime performance, disable all substates for
every PCIe root port.
Change-Id: Ic5bc8410709d0f0094810bc11a7723e88c30e397
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
All the boards based on the mc_ehl baseboard have a TPM which is
connected to SPI but mapped into the address space of the x86 so that
it acts like a LPC attached TPM. Enable the TPM driver so that it will
be used. In addition add the needed entry in devicetree.
Change-Id: I301d0ed4a108bac45d95eced120e7ba280945d9c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
All the mainboards based on mc_ehl use the external RTC RX6110SA.
Enable the driver in Kconfig for all boards based on mc_ehl. In
addition, as mc_ehl1 has the RTC attached to the SMBus, add the
devicetree entry on behalf of the SMBus device 00:1f.4 for this variant.
Change-Id: Ie1f45d0e6f9063c00253fe58a6268d40de91cf63
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56523
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
LTE module L850-GL may encounter U3 wakeup race condition with the host.
Setting xHCI LFPS periodic sampling off time to 0ms so that the host would not
miss the device-initiated U3 wakeup thus avoid the race condition.
BUG=b:193898133
BRANCH=dedede
TEST=flash the image to the device. Run following command to check the bits[7:4] is 0x0:
iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ic84dc83b749cf3c6029a06730096b64ef8cb8cd9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
TEST=Refer to `cbmem -t` output below:
Without this code changes, timestamp ids 962 and 963 are listed as
`unknown`.
962:<unknown> 1,704,863 (157)
963:<unknown> 1,704,878 (14)
With this code changes, lists the timestamps along with the timestamp
strings.
962:calling FspMultiPhaseSiInit 1,704,863 (157)
963:returning from FspMultiPhaseSiInit 1,704,878 (14)
Change-Id: I528567e4cc630e15dffffd1c7684798fcdde4535
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56641
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When looking for C compilers, xcompile uses the "" prefix to "gcc" and
"clang" as a last-resort option. This fails in environments where such
default names are blocked to prevent "unclean" builds - such as Chrome
OS.
Allow overriding this prefix using the GENERIC_COMPILER_PREFIX variable
that is hopefully both descriptive enough to suggest what it is for and
unusual enough to not trigger by chance.
Change-Id: I16239f66730f1dbcb7482f223cea4ee5957af10c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Updating from commit id 1e800ac83:
2021-03-01 22:59:54 +0000 - (docs: point md files in master to main/HEAD)
to commit id 4c21b57eb:
2021-07-19 11:36:07 +0000 - (pd: Fix missing polarity_rm_dts in some conditions)
This brings in 3145 new commits.
Change-Id: Iff2e9f766e750070d71644c2f9895ad10e8b1c9a
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56431
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id 96404aa27:
2021-05-13 18:27:27 +0200 - (Merge "build(hooks): update Commitizen to ^4.2.4" into integration)
to commit id 586aafa3a:
2021-07-19 05:36:18 +0200 - (Merge "errata: workaround for Neoverse V1 errata 1791573" into integration)
This brings in 207 new commits.
Change-Id: Iaf8af5ffaf377070ee1430ed7cfdc51001a1ba6b
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56416
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 4c569b52f6. This has
introduced a regression in mainboards using JSL SoC such that it
overrides the soft straps for all the GPIOs. This in turn has led to
some of the peripherals not working.
BUG=None
TEST=Build and boot to OS in Storo. Ensure that the regressed
peripherals are working back again.
Change-Id: Ibfeed1075fe28051b926ddd7ca771693dc19dae8
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56613
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add wifi sar for magister.
Due to fw-config cannot distinguish between magolor and magister.
Using sku_id to decide to load magister custom wifi sar.
BUG=b:192290227
TEST=build and test on magolor/magister
Cq-Depend: chrome-internal:3986580
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I4510cc2ad42a11ec802ecd439b353f8e87d63868
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This patch adds device tree settings to control pcie modphy tuning
FSP UPDs. With this patch, the pcie modphy can be tuned per board.
BUG=b:192716633
BRANCH=NONE
TEST=build dedede variant coreboot with fw_debug enable and check if
these settings have been changed successfully on fsp debug log.
Change-Id: I80a91d45f9dd8ef218846e1284fdad309313e831
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
LTE module L850-GL may encounter U3 wakeup race condition with the host.
Setting xHCI LFPS periodic sampling off time to 0ms so that the host would not
miss the device-initiated U3 wakeup thus avoid the race condition.
BUG=b:191426542
BRANCH=dedede
TEST=flash the image to the device. Run following command to check the bits[7:4] is 0x0:
iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I3be7adad49f87956a6764ad91fec6e76681b393f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Chiasheng Lee <chiasheng.lee@intel.com>
Since current AMD SoCs don't need some wait time between INIT and SIPI,
we can skip the 10ms wait there, which improves the boot time a bit.
before: CPU_CLUSTER: 0 init finished in 632 msecs
after: CPU_CLUSTER: 0 init finished in 619 msecs
mpinit still works on Mandolin and all CPU cores show up and are usable.
This also doesn't change the binary in a timeless build for boards/SoCs
that don't select X86_AMD_INIT_SIPI which I verified for lenovo/x230.
BUG=b:193885336
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1e044776f45021742a88a5e369a74383c1baaab6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The biosram accessor support in soc/amd/common/block/acpimmio/biosram.c
is only used on Stoneyridge and the old amd/southbridge code and not on
Picasso or Cezanne. It also only builds as a 32 bit binary and breaks
when trying to build as a 64 bit binary, since the size of an uintptr_t
is different on those two. There is no support for using the 32 bit
binaryPI with a 64 bit coreboot while there is code to use a 32 bit FSP
with 64 bit coreboot, so not building this for FSP-based SoC support
moves us one step closer to be able to build coreboot as 64 bit binary
for Picasso and Cezanne.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2d87ec2fa1b217eaf55d865e4390308812502e56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change does the following:
* Pushes the cpu_info struct into the top of the stack (just like
c_start.S). This is required so the cpu_info function works correctly.
* Adds the thread.c to the romstage build.
I only enabled this for romstage since I haven't done any tests in other
stages, but in theory it should work for other stages.
BUG=b:179699789
TEST=Boot guybrush with threads enabled in romstage
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8e32e1c54dea0d0c85dd6d6753147099aa54b9b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The alignment for `struct cpu_info` is wrong on x86_64. c_start.S uses
the `push` instruction when setting up the cpu_info struct. This
instruction will push 8 bytes but `unsigned int` is 4 bytes. By making
it a `size_t` we get the correct size for both x86_32 and x86_64.
BUG=b:179699789
TEST=Boot guybrush to the OS
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8ef311aaa8333ccf8a5b3f1f0e852bb26777671c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The structure and function are not currently used or implemented. x86 is
the only arch that currently implements it. It is currently used for
COOP_MULTITASKING and mp_init.
Keeping around the unused definitions leads to confusion.
BUG=b:179699789
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0775ef03168f7f9c41b1b05cb8f12724d0458ba5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
There is no reason this needs to be done in asm. It also allows
different stages to use threads. If threads are no used in a specific
stage, the compiler will garbage collect the space.
BUG=b:179699789
TEST=Boot guybrush to the OS
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib5a84a62fdc75db8ef0358ae16ff69c20cbafd5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56531
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It can be nice to update the TPM firmware without having to clear the
TPM owner. However, in order to do so would require platformHierarchy
to be enabled which would leave the kernel antirollback space a bit
vulnerable. To protect the kernel antirollback space from being written
to by the OS, we can use the WriteLock command. In order to do so we
need to add the WRITE_STCLEAR TPM attribute.
This commit adds the WRITE_STCLEAR TPM attribute to the rw antirollback
spaces. This includes the kernel antirollback space along with the MRC
space. When an STCLEAR attribute is set, this indicates that the TPM
object will need to be reloaded after any TPM Startup (CLEAR).
BUG=b:186029006
BRANCH=None
TEST=Build and flash a chromebook with no kernel antirollback space set
up, boot to Chrome OS, run `tpm_manager_client get_space_info
--index=0x1007` and verify that the WRITE_STCLEAR attribute is present.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I3181b4c18acd908e924ad858b677e891312423fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56358
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Realtek speaker amplifiers under auto mode operation have Absolute Max
Rating (AMR) at 1.98 V. Hence probe the firmware config for speaker
amplifier and program the VCCIOSEL accordingly.
BUG=b:194120188
TEST=Build and boot to OS in Gallop. Ensure that the VCCIO selection is
configured as expected and probing the GPIO reads the configured
voltage.
Change-Id: Ifa0b272c23bc70d9b0b23f9cc9222d875cd24921
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Jasperlake is one of the few SoCs that support programmable VCCIO
selection and this support is used by Dedede mainboard.
BUG=b:194120188
TEST=Build and boot to OS in Gallop. Ensure that the VCCIO selection is
configured as expected and probing the GPIO reads the configured
voltage.
Change-Id: I54def27a499ccba7fd25cab1048fdca06dbc535f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56536
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some of the Intel SoCs with more than 2 PAD configuration registers
support programming VCCIO selection. Add a pad configuration macro to
program VCCIO selection when the GPIO is an output pin.
BUG=b:194120188
TEST=Build and boot to OS in Gallop. Ensure that the VCCIO selection is
configured as expected and probing the GPIO reads the configured
voltage.
Change-Id: Icda33b3cc84f42ab87ca174b1fe12a5fa2184061
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56507
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Verstage even fits in 44K so one can comfortably increase the
bootblock size. This is need for the followup patches that turn
console methods into drivers, which increase the bootblock a little,
but still too much for the the bootblock to fit in the alloted size on
this platform.
Change-Id: If1eaf2b495e3032d156433fd0728134a66f4e49b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56521
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Provide an option to set xHCI LFPS period sampling off time
(SS_U3_LFPS_PRDC_SAMPLING_OFFTIME_CTRL in JSL EDS revision 2.0).
If the option is set in the devicetree, the bits[7:4] in
xHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated.
The host will sample LFPS for U3 wake-up detection when suspended, but
it doesn't sample LFPS at all time due to power management, the
default xHCI LFPS period sampling off time is 9ms. If the xHCI LFPS
period sampling off time is not 0ms, the host may miss the
device-initiated U3 wake-up and causes some kind of race condition for
U3 wake-up between the host and the device.
BUG=b:187801363, b:191426542
TEST=build coreboot with xhci_lfps_sampling_offtime_ms and flash
the image to the device. Run following command to check the bits[7:4]:
iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Ben Kao <ben.kao@intel.com>
Change-Id: I0e13b7f51771dc185a105c5a84a8e377ee4d7d73
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Currently, BT offload is disabled/enabled unconditionally based on the
devicetree settings. BT offload uses I2S lines and cannot be enabled
when a I2S based audio daughter card is active. So we need to enable
BT offload only while using soundwire based audio daugther card.
BUG=b:175701262
TEST=Verified BT offload on brya with soundwire audio daughter card
BT offload enabled
Change-Id: I6a9ad463e13e2cfcfc3b7de5a61a25cdef0641f7
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Move the event logging helpers defined in acpi into a separate library.
This will allow logging power management and GPE events for both S3 and
Modern Standby. Introduce a single helper acpi_log_events function to
log both PM and GPE events.
BUG=None
TEST=Build and boot to OS in Guybrush.
Change-Id: I96df66edfc824eb3db108098a560d33d758f55ba
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
It appears the pspp_policy enum is not the same as the FSP definition
currently being used. This means that the incorrect PSPP value setting
would get read by FSP. For Zork programs this meant we actually were
setting links as DXIO_PSPP_BALANCED instead of DXIO_PSPP_POWERSAVE.
This change adds DXIO_PSPP_DISABLED as the first enum value to properly
match the FSP definition and adjusts non AMD Customer Reference Boards
that reference the enum to still send the same value even though it has
now change definitions. If we actually want DXIO_PSPP_POWERSAVE for
those boards that can be adjusted in a future change.
BUG=b:193495634
TEST=Boot to OS with Majolica and Guybrush and run 10G iperf on wifi
with other server on local network.
Change-Id: I287b6d3168697793a2ae8d8e68b4ec824f2ca5ef
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
- The WWAN card was being disabled later than desired.
- The SD card was never being placed into reset on BoardID 1.
- Enable Touchscreen power
- Enable PCIe_RST1 at the same points as PCIe_RST
- Remove Redundant Bootblock settings
BUG=b:193036827
TEST=Build & Boot, look at GPIO states through boot process
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I5431da755d98e4ad0b300d01cac562d61db0bc08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This is in preparation for migrating EDK2 to more recent version(s). In
EDK2 repo commit f2cdb268ef appended an additional field to FSP 2.0
header (FspMultiPhaseSiInitEntryOffset). This increases the length of
the header from 72 to 76. Instead of checking for exact length check
reported header length against known minimum length for a given FSP
version.
BUG=b:180186886
TEST=build/boot with both header flavors
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Change-Id: Ie8422447b2cff0a6c536e13014905ffa15c70586
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56190
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
New binutils versions automatically resolve references to debug symbol
files and parse their content as well when objdump'ing data. This leads
to multiple mentions of symbols, so deduplicate references.
Change-Id: I5d597399c515904313ba36d7aab9178bc0dade14
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Set the bus master bit only if the global Kconfig switch
PCI_ALLOW_BUS_MASTER_ANY_DEVICE is enabled. For now the bus master bit
is needed for i210 because of some old OS drivers that do not set it
and won't work properly without it.
Change-Id: I6f727e7f513f4320740fbf49e741cea86edb3247
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This legacy alt-century byte sits amidst CMOS and conflicts many option
tables. It usually has no meaning to the hardware and needs to be main-
tained manually. Let's disable its usage by default if the CMOS option
table is enabled.
Change-Id: Ifba3d77120c2474393ac5e64faac1baeeb58c893
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Chrome EC is relatively quick with retiring "old" boards from their
tree so when upreving it, the last veyron in that list that wasn't
commented out is gone as well.
Change-Id: Ie1ef693c8d0947396ee01e5aa5f40ef36c8a317a
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56430
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
EC_IN_RW_OD signal is routed from Google Security Chip to GPIO_91 in the
upcoming hardware build. The existing SD_EX_PRSNT signal is dropped in
the upcoming hardware build because SD7 support is dropped. Export the
EC_IN_RW GPIO for use by payload.
BUG=None
TEST=Build and boot to OS in Guybrush. Ensure that the device can boot
successfully in both recovery and normal mode.
Cq-Depend: chromium:3043702
Change-Id: I8986ba007a2d899c510be61664d90430b8d2d384
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56493
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
While the gcc(1) driver has the `-nostartfiles` option, ld(1), the
program the coreboot toolchain uses to link the object files, doesn't
have it.
In binutils before 2.36, this option is interpreted as `-n -o
startfiles`, in which the `-o` option is overridden by a later `-o`
option, so only the `-n` option has effect, which is the `--nmagic`
long option of ld(1). So the correct linker option in this place is
`--nmagic`.
It is tested that without `--nmagic`, ld can generate a much bigger
x86_64 romstage, so this option is still needed.
This error is found when trying to update binutils to 2.36 and later
versions, where ld(1) is unable to disambiguate options and reports an
error.
Change-Id: I27dc2209abdc6fec866716a252736c5cf236a347
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
There are in total three USB ports that are used on mc_ehl1:
- Port 1: Type A connector connected to USB2/USB3 port 0
- Port 2: Type A connector connected to USB2/USB3 port 1
- Onboard: connected to USB2 port 2
None of the ports supports overcurrent reporting.
Adjust the appropriate UPDs in devicetree to match the hardware
configuration.
Change-Id: I220637b8e9f03efccacd0955e82cfc0c7a6f53ee
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56454
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Without this configuration, even though there is no SD card it shows as
SD card is present and host controller waits for card to respond.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board with SD card and
without SD card, make sure if SD card not present then host controller
should not wait for card to respond.
Change-Id: I5dc5ba10c98d606d98e7d4f4c41c3e4f45e94452
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
The common gpio driver can be re-used for SC7180,
thus remove the existing gpio driver support and
also clean up the common macro definitions.
Add GPIO pin details specific to SC7180 chipset
for the consumers to be able to request for the
gpio functionality as per their requirement.
TEST=Validated on qualcomm sc7180 development board
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Change-Id: Ifd206e6bc9a549706e7a2c4bde0b7d5527ca6268
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
This enables the MCAX checking and BERT entry generation for Cezanne.
TEST=When printing all registers of all MCAX banks of core 0 on a
google/guybrush device, the registers have values that look correctly
and there is no general protection fault, so all MCAX MSRs that could be
accessed exist on Cezanne.
BUG=b:192997706
Change-Id: Ibe8047ce5bb5e7136a8786693bcced4d2225b1fd
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56345
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable RSA and SHA for cezanne since support has been added to the PSP.
Also picasso and cezanne have different enums definitions for
hash algorithm, so split that out into chipset.c.
BUG=b:187906425
TEST=boot guybrush, check cbmem -t and the logs
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I725b0cac801ac0429f362a83aa58a8b9de158550
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Create the taeko variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:193685558
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_TAEKO
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: If738849bc3103c52a4c4d8a8aaef3f90a62ad5c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56385
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch makes Ampton EC wake up AP from s0ix when the state of
charge drops to 2%.
Demonstrated as follows:
1. Boot Ampton.
2. Run powerd_dbus_suspend.
3. On EC, run battfake 2.
4. System resumes.
BUG=b:189540432
BRANCH=Octopus
TEST=Verified on Ampton.
Change-Id: I98d8e6ea185e8782ad675d4668678b341ca5d350
Signed-off-by: James Chao <james_chao@asus.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56341
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The dependency file, generated by
$(HOSTCC) ... -MMD -MT $@ -c $< -o $@.orig
is determined by replacing the suffix of "$@.orig" with ".d", resulting
in "$@.d" (which is *.o.d). The file name was accidentally changed in
CB:55360. Now explicitly specify the path by the "-MF" option.
BUG=none
TEST=make unit-tests; find build/tests/ -name "*.d"
BRANCH=none
Change-Id: I01f77ebaaae78dd9e69394a49e524f1013857195
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
As part of GPIO driver cleanup across qcom chipsets,
GPIO_OUTPUT_ENABLE has been renamed to GPIO_OUTPUT.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 development board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I51eedc722a91c5ea8e009fb8468a60667d374b49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
This patch sets the optimized FIVR configs for ehlcrb customized
based on the performance measurements to achieve the better power
savings in sleep states.
- Enable the external V1p05, Vnn, VnnSx rails in S0i3, S3, S4, S5
states.
- Update the supported voltage states.
- Update max supported current, voltage transition time and RFI
spread spectrum.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I1e30ff6d84bfe078fcce0f968fce6aaab7fd575b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55981
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These methods are oprom specific. Move them out of CBFS. I also deleted
the tohex methods and replaced them with snprintf.
BUG=b:179699789
TEST=Boot guybrush and see oprom still loads
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I03791f19c93fabfe62d9ecd4f9b4fad0e6a6146e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56393
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
If we don't escape the $ then the actual $(obj) path will be written
into the .config file. With this change `$(obj)` is written into the
.config file. The Makefile then does:
PSP_VERSTAGE_FILE=$(call strip_quotes,$(CONFIG_PSP_VERSTAGE_FILE))
Since this is a recursive assignment the $(obj) will be expanded at that
point.
This change makes it easier to compare full .config files.
BUG=none
TEST=Build ezkinil
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic961df148d3f22585f3441d75c3f2454329c678a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
This change allows preloading the payload.
BUG=b:179699789
TEST=Boot guybrush and see payload read/decompress drop by 20 ms. We
now spend 7ms decompression from RAM. By switching to LZ4 we drop that
to 500us.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3ec78e628f24f2ba0c9fcf2a9e3bde64687eec44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
FILO allows to configure a line to autoboot. Hook this up into
coreboot’s build system.
TEST=Configure coreboot for QEMU i440fx with FILO as payload and
configure:
CONFIG_FILO_MASTER=y
CONFIG_FILO_USE_AUTOBOOT=y
CONFIG_FILO_AUTOBOOT_FILE="hda1:/vmlinuz root=/dev/sda1 console=tty0 console=ttyS0,115200 initrd=hda1:/initrd.img"
CONFIG_FILO_AUTOBOOT_DELAY=5
Boot Debian image with:
qemu-system-x86_64 -bios /dev/shm/coreboot/build/coreboot.rom -L /dev/shm -enable-kvm -smp cpus=2 -m 1G -hda /dev/shm/debian-32.img -serial stdio -net nic -net user,hostfwd=tcp::22222-:22
Change-Id: Id167e9a144bf466da87469108002672b299b702a
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This CL adds a method that can start the processes of reading the APOB
from SPI. It does require more RAM in ramstage since we no longer mmap
the buffer in the happy path. This will allow us to reduce our
boot time by ~10ms. The SoC code will need to be updated to call
start_apob_cache_read at a point where it makes sense.
BUG=b:179699789
TEST=With this and the patches above I can see a 10 ms reduction in
boot time on guybrush.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I930d58b76eb4558bc4f48ed928c4d6538fefb1e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56232
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If a thread wants to block a state transition it can use
thread_run_until. Otherwise just let the thread run. `thread_join` can
be used to block on the thread. Boot states are also a ramstage concept.
If we want to use this API in any other stage, we need a way of starting
a thread without talking about stages.
BUG=b:179699789
TEST=verify thread_run no longer blocks the current state
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3e5b0aed70385ddcd23ffcf7b063f8ccb547fc05
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56351
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The thread_handle can be used to wait for a thread to exit. I also added
a return value to the thread function that will be stored on the handle
after it completes. This makes it easy for the callers to check if the
thread completed successfully or had an error. The thread_join
method uses the handle to block until the thread completes.
BUG=b:179699789
TEST=See thread_handle state update and see error code set correctly.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ie6f64d0c5a5acad4431a605f0b0b5100dc5358ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56229
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is no telling when the next udelay will be, so explicitly call
`thread_yield()` after completing a transaction. This will allow any
pending transactions to immediately start.
BUG=b:179699789
TEST=Verify new transaction is enqueued right after another.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9c1272bde46c3e0c15305b76c2ea7a6dde5ed0b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56321
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Once we enable COOP_MULTITASKING, we need to guarantee that we don't
have multiple threads trying to access the DMA hardware.
BUG=b:179699789
TEST=Boot guybrush with APOB patches.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ibb8e31c95d6722521425772f4210af45626c8e09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56231
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Switching threads while holding a spinlock can lead to a deadlock. This
happens if you have two thread trying to print to the serial console
because the uart code uses udelay.
BUG=b:179699789
TEST=Boot guybrush and no longer see a deadlock when printing to
console from a second thread.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1b929070b7f175965d4f37be693462fef26be052
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change allows nesting critical sections, and frees the caller from
having to keep track of whether the thread has coop enabled.
BUG=b:179699789
TEST=Boot guybrush with SPI DMA
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I325ab6181b17c5c084ca1e2c181b4df235020557
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56350
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
idle_thread_init was actually configuring the BSP thread at the end.
We can instead do this in threads_initialize. This now lets us set
initialized after the idle thread has been set up.
BUG=b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I7f1d6afac3b0622612565b37c61fbd2cd2481552
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56356
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change will make it so the standard rdev readat call will use the
SPI DMA controller if the alignment is correct, and the transfer size is
larger than 64 bytes.
There is a magic bit that needs to be set for the SPI DMA controller to
function correctly. This is only available in RN/CZN+.
BUG=b:179699789
TEST=Boot guybrush to OS. This reduces loading verstage by 40ms,
verifying RW by 500us and loading romstage by 500 us.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0be555956581fd82bbe1482d8afa8828c61aaa01
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Elkhart Lake provides option to configure FIVR (Fully Integrated
Voltage Regulators) via parameters in FSP-S.
This CL removes fixed FIVR config values and expose these parameters
to the devicetree so that they can be configured on mainboard level
as needed.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ie1b0e0cc908ba69805dec7682100dfccb3b9d8b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The patch updates PMC Descriptor which is part of Descriptor Region if
system equipped with Alder lake A0 silicon. This change allows to use
unified Descriptor Region for Alder lake A0(CPU ID:0x906a0) and B0
(CPUD ID:0x906a1) silicons. The change has to be reverted before EOM is
enableda on the system.
BUG=B:187431859
TEST=Verified PMC Descriptor getting modified for Alder lake B0 silicon
if not updated.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I2a1f60fda7575212bb694fc423bd229452515903
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch removes all local `CPUID_` macros from SoC directories and
creates a common cpu_ids.h inside include/cpu/intel/cpu_ids.h. SoC
users are expected to add any new CPUID support into cpu_ids.h and
include 'cpu/intel/cpu_ids.h' into respective files that look for
`CPUID_` macro.
Note: CPUIDs for HSW, BDW and Quark are still inside the respective
directory.
Change-Id: Id88e038c5d8b1ae077c822554582410de6f4a7ca
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The setting `chipset_lockdown` has the same configuration for all
variants and they also match with the baseboard configuration. Thus,
remove it from the variant overridetrees.
Built google/delbin with `BUILD_TIMELESS=1` and coreboot.rom
remains the same.
Change-Id: I597e4487e7a0e1848d2a2f2c8f8ebd552994aac2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56199
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The configuration of the setting `chipset_lockdown` doesn't have any
effect for most of the variants since their configuration of
`common_soc_config` overwrites the configuration of the baseboard's
devicetree. If `chipset_lockdown` is configured separately in the
baseboard devicetree, the variant overridetrees reuse its
configuration.
Thus, move `chipset_lockdown` out of `common_soc_config` in the
baseboard devicetree and configure it separately.
Change-Id: I595c042cf62680d61f60965710d382bfdcd81671
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56209
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure GPIO DGI_D4 (AP_XHCI_INIT_DONE) as output, so that payloads
(for example depthcharge) can assert it to notify EC to enable USB VBUS.
BUG=b:193499785
TEST=emerge-cherry coreboot
BRANCH=none
Change-Id: I21b7b811b8138cb3f71efecb0a0a886905c65a9c
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The patch adds an interface for configuring GPIOs inside the Kontron
CPLD/EC. This allows to statically define the mode for each GPIO pin
in devicetree.cb of the motherboard or carrier board. For example:
chip ec/kontron/kempld
device gpio 0 on
register "gpio[0]" = "KEMPLD_GPIO_INPUT"
register "gpio[4]" = "KEMPLD_GPIO_OUTPUT_LOW"
register "gpio[5]" = "KEMPLD_GPIO_OUTPUT_HIGH"
register "gpio[11]" = "KEMPLD_GPIO_DEFAULT"
end
end
In this case, <device gpio 0>, like all other devices, is not a real
device inside the EC. These definitions are used to understand the EC
resources and systematize configuration options, but if mark this as
<off>, the initialization step will be skipped in the driver code.
Use KEMPLD_GPIO_DEFAULT or skip it in devicetree.cb to not configure
the GPIO and keep the default mode after CPLD reset.
This work is based on code from the drivers/gpio/gpio-kempld.c linux
driver. Tested on Kontron mAL-10 COMe module [1].
[1] CB:54380 , Change-Id: I7d354aa32ac8c64f54b2bcbdb4f1b8915f55264e
Change-Id: Id767aa451fbf2ca1c0dccfc9aa2c024c6f37c1bb
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47595
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In hardwaremain.c we call console_init before threads_initialize. Part
of setting up the uart requires calling udelay which then calls
thread_yield_microseconds. Since threads have not been set up, trying to
yield will result in bad things happening. This change guards the thread
methods by making current_thread return NULL if the structures have not
been initialized.
BUG=b:179699789
TEST=Ramstage no longer hangs with serial enabled
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If9e1eedfaebe584901d2937c8aa24e158706fa43
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56318
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This aligns the mca_check_all_banks implementation in the common mca.c
with the one in the common mcax.c file. Do the MCA bank count check
before the !is_warm_reset() check, so that a mismatch also gets printed
on the cold boot path.
Change-Id: Idbd3e9ce9c7483f84f87adab7adac47335cd59aa
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
For Cezanne stubs are added for the functions that the SoC-specific code
needs to provide. Since the mca_is_valid_bank stub on Cezanne always
returns false, the checks get skipped for it at the moment. The actual
functionality will be added in a later patch.
Change-Id: Ic31e9b1ca7f8fac0721c95935c79150d7f774aa4
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
To factor out the rest of the common MCAX code, mca_bank_name[] may only
be accessed by accessor functions, so implement this for the last place
that still accessed mca_bank_name[] directly.
Change-Id: Ic6548d3ceeb9c00ad344fc0bb3d97893e17a43a9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56294
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Alder Lake SoC has virtual GPIOs for community 1 which was being
programmed by FSP and hence was skipped by coreboot. As part of
moving most of the GPIO programming to coreboot, we're skipping this
programming in FSP now.
TEST=Check register offset to see if programming is correct.
Change-Id: I4d48553d14465df50e5aaaf27ab26c6a1b70d4cf
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55270
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Fast Read Dual Output and Fast Read Dual I/O commands are
practically identical, the only difference being how the read address is
transferred (saving a whooping 2 bytes which is totally irrelevant for
the amounts of data coreboot tends to read). We originally implemented
Fast Read Dual Output since it's the older command and some older
Winbond chips only supported that one... but it seems that some older
Macronix parts for whatever reason chose to only support Fast Read Dual
I/O instead. So in order to make this work for as many parts as
possible, I guess we'll have to implement both. (Also, the Macronix
device ID situation is utter madness with different chips with different
capabilities often having the same ID, so we basically have to make a
best-effort guess to strike a trade-off between fast speeds and best
chance at supporting all chips. If this turns out to be a problem later,
we may have to add Kconfig overrides for this or resort to SFDP parsing,
although that would defeat the whole point of trying to be fast.)
BUG=b:193486682
TEST=Booted CoachZ (with Dual I/O)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ia1a20581f251615127f132eadea367b7b66c4709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
To be able to enable & disable PSP_verstage in the saved .config file,
the symbol VBOOT_STARTS_BEFORE_BOOTBLOCK needs to be changed from a
select to a default with a prompt.
BUG=182477057
TEST=Build, get PSP_verstage, disable VBOOT_STARTS_BEFORE_BOOTBLOCK,
verify that VBOOT_STARTS_IN_BOOTBLOCK is set.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iba735f33f9b079c9868ef2fff099c5298ff72b6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56289
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initially APL was considered as IFDv2 platform irrespective being
added into ifd_2_platforms[], hence commit hash 621ed4c had migrated
APL into IFDv1 which break its FLMSTR1/FLMSTR2/FLMSTR3 Read/Write
access. This change adds APL into the list of IFDv2 platforms to fix
booting issue on the LeafHill board.
Change-Id: Ied59ddb2fe05b421266a6b119fd6eab17b8beedc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56300
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rick Lee <rick.lee@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch changes the way how the not implemented MCA bank 3 gets
skipped. For the not implemented bank 3 the name gets set to NULL
resulting in mca_is_valid_bank returning false causing the bank to get
skipped. This is a preparation for commonizing the MCA(X) handing in the
soc/amd sub-tree.
Change-Id: I40d6a6752504d804c45b445fce7e763e80161211
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
In mca_check_all_banks only check valid MCA banks for errors. This
aligns the Picasso code a bit more with the Stoneyridge code base which
will be updated in a follow-up patch. This is a preparation for
commonizing the MCA(X) handing in the soc/amd sub-tree.
Change-Id: I0c7f3066afd220e6b8bf8308a321189d7a2679f6
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56275
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A regular assignment works just as well and also allows type-checking.
It also avoids a common mistake where `sizeof` is applied to a pointer
to obtain the size of the data it points to, without dereferencing it.
Found-by: Coverity CID 1458231
Change-Id: I7ed05322c3c911f3da4145f81e4d9760a275fec2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56265
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ESPI & LPC keywords were added for the zork program, but it was
found that they weren't needed, so they were never used. The previous
patch removes them from sconfig, so now they aren't needed in coreboot.
BUG=None
TEST=Build
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I9ae7817bb63d69ee272103b2d1186f125e188950
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56278
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to the AMD FCH architects, we should be using the default
value for the NO_HOG bit. This fixes a problem where the SPI DMA no
longer functions after the LPC init runs.
BUG=b:179699789, b:192373221
TEST=Boot guybrush and see SPI DMA working
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If015869657f36d3533f4ab9ebd1f54b0d4eb283a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
There is no technical reason this needs to be done in romstage. Moving
it into ramstage allow us (in future CLs) to use threads to pre-load
the apob from SPI.
BUG=b:179699789
TEST=Boot and Ezkinil and Guybrush and verify APOB update still work
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I960437ff4400645de5a3e7447fcdbc52de85943e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The %p format specifier already prints out 0x, so remove the 0x from the
string. I also updated the other format specifiers to use the %# syntax
to print out the 0x.
BUG=b:179699789
TEST=see correct format.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5b00d2c06687e549f69486eb5e18f7bed560b2ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56225
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Building nvramcui with i386-elf-gcc (coreboot toolchain
v2021-04-06_7014f8258e) 8.3.0 and Link Time Optimization (LTO) enabled
in libpayload (`CONFIG_LP_LTO=y`) fails with the error below.
LPGCC nvramcui.bin
curses/PDCurses/pdcurses/refresh.c: In function 'wrefresh':
curses/pdcurses-backend/pdcdisp.c:217:4: error: 'bg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
curses/pdcurses-backend/pdcdisp.c:214:18: note: 'bg' was declared here
curses/pdcurses-backend/pdcdisp.c:217:4: error: 'fg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
curses/pdcurses-backend/pdcdisp.c:214:14: note: 'fg' was declared here
lto1: all warnings being treated as errors
lto-wrapper: fatal error: i386-elf-gcc returned 1 exit status
compilation terminated.
/opt/xgcc/lib/gcc/i386-elf/8.3.0/../../../../i386-elf/bin/ld.bfd: error: lto-wrapper failed
collect2: error: ld returned 1 exit status
`pair_content()` returns in case `PAIR_NUMBER(attr)` is invalid, so
guard the usage of `serial_set_color()`.
if (pair < 0 || pair >= COLOR_PAIRS || !fg || !bg)
return ERR;
Note, building with x86_64-linux-gnu-gcc-10 (Debian 10.2.1-6) 10.2.1
20210110 does *not* fail.
Change-Id: Ic63e34f2b5bc9f826db37597bebc6b20542481d7
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch replaces the usage of GPR (General Purpose Registers) like
ECX and EBX for backing up data way and non-eviction mask with SPR
(Special Purpose Registers) EDI and ESI.
Purpose of this change is to ensure the safety while developers might
use ECX often while doing rdmsr/wrmsr rather than making use of EDI.
TEST=Able to boot JSL and TGL platform without any hang using eNEM.
Change-Id: I12e0cb7bb050e4f7b17ecf30108db335d1d82ab7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56161
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SaGv is only available on ULT/ULX processors, which use PCH-LP. Given
that the Siemens Chili board selects `SOC_INTEL_CANNONLAKE_PCH_H`, it
does not use ULT/ULX processors, and thus does not support SaGv. Drop
the `SaGv` setting from the devicetrees, as it has no effect.
Change-Id: I5be518cce08206ad149efd1665e44a7111b24202
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56205
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the common mca_get_bank_count function instead of open-coding the
functionality to get the MCA bank number. Also re-type the num_banks
variable from signed in to unsigned int, since the number of MCA bank is
always positive, and make it constant.
Change-Id: I449c74629ff16057c4559d7fd3620208230560f5
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56245
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the common mca_get_bank_count function instead of open-coding the
functionality to get the MCA bank number. Also re-type the num_banks
variable from signed in to unsigned int, since the number of MCA bank is
always positive, and make it constant.
In the case of Intel model 2065x the mca_get_bank_count() call replaces
a magic number.
Change-Id: I245b15f57e77edca179e9e28965383a227617174
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56244
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When accessing the MCA MSRs, the MCA bank number gets multiplied by 4
and added to the IA32_MC0_* define to get the MSR number. Add a macro
that already does this calculation to avoid open coding this repeatedly.
Change-Id: I2de753b8c8ac8dcff5a94d5bba43aa13bbf94b99
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56243
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Only the fields bank and sts from the mca_bank struct were used outside
a local scope, so remove the rest. Also rename the struct that now only
contains the bank number and the status MSR content to mca_bank_status.
Change-Id: I925347dff950ac2bd021635ca988c02fba48df7f
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56237
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Those registers are architectural MSR and this also gets them in line
with IA32_MC0_CTL and IA32_MC0_STATUS. Also move them below the
definitions for IA32_MC0_STATUS, so that the numbers of the MSRs are
ascending.
Change-Id: Icef6526c896720248f5b648ddf1a271bdf46917c
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56235
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since initial_lapicid() returns an unsigned int, change the type of the
local variables the return value gets assigned to to unsigned int as
well if applicable. Also change the printk format strings for printing
the variable's contents to %u where it was %d before.
Change-Id: I289015b81b2a9d915c4cab9b0544fc19b85df7a3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55063
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This was originally several commits that had to be squashed into one
because the intermediate states weren't able to build coreboot:
- one to remove everything that wasn't our own code, leaving only
regex.[ch], toada.c, description.md and Makefile.inc.
- one to copy in Linux 5.13's scripts/kconfig and adapt Makefile.inc
to make the original Makefile work again.
- adapt abuild to use olddefconfig, simplifying matters.
- apply patches in util/kconfig/patches.
- Some more adaptations to the libpayload build system.
The patches are now in util/kconfig/patches/, reverse applying them
should lead to a util/kconfig/ tree that contains exactly the Linux
version + our own 5 files.
Change-Id: Ia0e8fe4e9022b278f34ab113a433ef4d45e5c355
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
I a file in configs/* has no suffix, then the default configuration
will override the results of the build generated by the configfile
from configs/*. Fix this by adding a '_' to the buildname.
Change-Id: Ic47105fafca41f1905a6569943079623bec5405a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Clean up lockdown configuration and move it to the baseboard's
devicetree.
Since most of the mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, use it
for the rvp8 variant for consistency as well.
Built intel/rvp11 with `BUILD_TIMELESS=1` and coreboot.rom remains
identical. intel/rvp8 changes, as expected.
Change-Id: I78e847c321c61c3a974b26f30bc2823ff84df651
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56212
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The headers added are generated as per FSP v2237_00.
Previous FSP version was v2207_01.
Changes Include:
- Add VccInAuxImonIccImax in FspsUpd.h
- Adjust Reserved UPD Offset in FspmUpd.h and FspsUpd.h
- Few UPDs description update in FspmUpd.h and FspsUpd.h
BUG=b:192199787
BRANCH=None
TEST=Build and boot brya
Change-Id: Ie291204a3fa0b9451c418c84bd40a17ef08a436c
Cq-Depend:chrome-internal:3970327,chrome-internal:3925290
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55896
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The coreboot SMBus driver requires additional changes to accomodate
the DDR5 EEPROM read which has resulted in a broken code flow for boot.
This CL serves as a temp WA to let FSP perform the SPD read for DDR5
and pass SPD addresses to FSP UPD array.
BUG=b:180458099
TEST=Build and boot DDR5 adlrvp to OS
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I9998bfcd12b81c11fcc9f791da2a27d3c788e48a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50996
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some devices were missing from the IRQ table, and this lack of
IRQ programming for the devices (although unused), was causing S0ix
entry to fail.
BUG=b:176858827
TEST=suspend_stress_test -c10 passes, EC observes SLP_S0IX# toggle
correctly upon entry/exit from S0ix
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ia7612ee008842ba2b8dcd36deb201f4f26130660
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
This reverts commit ce0e2a0140 which was
originally introduced as a workaround for the bug that the Linux kernel
doesn't know what to do with type 16 memory region in the e820 table
where CBMEM resides and disallowed accessing it. After depthcharge was
patched to mark the type 16 region as a normal reserved region, the
Linux kernel now can access the BERT region and print BERT errors. When
SeaBIOS was used as payload it already marked the memory region
correctly, so it already worked in that case.
After commit 8c3a8df102 that removed the
usage of the BERT memory region reserved by the FSP driver by the AMD
Picasso and Cezanne SoCs and made them use CBMEM for the BERT region,
no other SoC code uses this functionality. The Intel Alderlake and
Tigerlake SoCs put the BERT region in CBMEM and never used this reserved
memory region and the change for the Intel server CPU to use this was
abandoned and never landed in upstream coreboot. AMD Stoneyridge is the
only other SoC/chipset that selects ACPI_BERT, but since it doesn't
select or use the FSP driver, it also won't be affected by this change.
TEST=Behavior of the BERT code doesn't change on Mandolin
Change-Id: I6ca095ca327cbf925edb59b89fff42ff9f96de5d
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56163
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the common mca_get_bank_count function instead of open-coding the
functionality to get the MCA bank number. Also re-type the num_banks
variable from signed in to unsigned int, since the number of MCA bank is
always positive.
Change-Id: I126767cf9ad468cab6d6537dd73e9b2dc377b5c4
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
If two generic devices use the same number, device coming later
overrides the earlier device, as a result of this the static.c has
only one device.
In the case where we have UFC set to UFC_USB, this will result in
no IPU device scope in SSDT, since its entry will be set to disbled
after UFC probe.
TEST=Build, Boot and Check UFC camera preview with UFC=UFC_USB
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I034cb7da787313d1cb53484922149589ac0f1c5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Use the common mca_get_bank_count function instead of open-coding the
functionality to get the MCA bank number. Also re-type the num_banks
variable from signed in to unsigned int, since the number of MCA bank is
always positive.
Change-Id: I70ad423aab484cf4ec8f51b43624cd434647aad4
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
In multiple locations within the coreboot tree the IA32_MCG_CAP MSR gets
read and masked with MCA_BANKS_MASK to get the number of available MCA
banks on the CPU, so add this to the common code to avoid duplication
of code.
Change-Id: Id118a900edbe1f67aabcd109d2654c167b6345ea
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This change only enables the IOMMU device. We still require the IVRS
table to take advantage of the IOMMU. This will happen when the picasso
IVRS code is moved into common.
BUG=b:190515051
TEST=lspci shows IOMMU device
00:00.2 IOMMU: Advanced Micro Devices, Inc. [AMD] Device 1631
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5c7cae3d25af5a45d48658ffa948a2856adc4346
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
We need to reference correct USB port number for driver to
identify type-C port number correctly.
BUG=b:189476816
BRANCH=None
TEST=Check the transactions are happening on correct port. Also checked
retimer firmware update on both the ports.
Change-Id: I20c088ee81610155067abad086eba8d72f73ad60
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Since TBT controller can have maximum 2 ports per controller, our
code will loop over DFP structure twice and determine port number.
Retimer driver used to assign port number as below:
1. Check if power GPIO is assigned for particular DFP entry or not
2. If entry is there, assign loop count as port number
Since loop count is 2, retimer will never assign port number = 2
even if it's present. In case of more than 1 controller, port number
assigned will still be 0 or 1 even though actual port index might
be 2 or 3. This will create an issue where even if you do transaction
on device on controller 2 (port index 2 or 3), EC will route it on
port 0 or 1 due to incorrect port index.
Update the driver flow as per below to handle this scenario:
1. Check if power GPIO is assigned for particular DFP entry or not
2. Get USB port number from config since it's stored in usb port
information under devicetree
3. Pass the port number to ACPI SSDT and EC code
Above changes will ensure that we're assigning correct port
number as per calculation and EC will use correct port index.
BUG=b:189476816
BRANCH=None
TEST=Checked that retimer firmware update works on both ports and update
happens on correct port index.
Change-Id: Ib11637ae39046e0afdacd33bc34e8a59e6f2bfb1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Create a separate function to get PLD information from USB device.
This is helpful in retimer driver where we can attach same USB
port information to retimer instance and we can avoid duplication
of information.
BUG=None
BRANCH=None
TEST=Check if code compiles and function returns correct value
Change-Id: Iaaf140ce1965dce3a812aa2701ce0e29b34ab3e7
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The Majolica UEFI ACPI tables have this listed as shared. It's already a
level interrupt, so no reason it shouldn't be shared.
This change makes it so Windows can correctly initialize the GPIO
controller.
BUG=b:186212501
TEST=Boot guybrush to windows and see GPIO controller functional. Also
boot guybrush to windows and verify GPIO controller still works.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I48c6d548a2a8d67599f25e37eeafc90764d9e2d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Create the kano variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:193052432
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_KANO
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ib0670e346c113291054cb92fb57aae52f844e8c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56155
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 1aa60a95bd broke microcode loading for chipsets that have a
microcode blob with a total_size field set to 0. This appears to be
support for older chipsets, where the size was set to 0 and assumed to
be 2048 bytes. The fix is to change the result of the subtraction to a
signed type, and ensure the following comparison is done without
promoting the signed type to an unsigned one.
Resolves: https://ticket.coreboot.org/issues/313
Change-Id: I62def8014fd3f3bbf607b4d58ddc4dca4c695622
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56153
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Stefan Ott <coreboot@desire.ch>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All of the build configuration is set to produce big endian image on PPC64.
In addition, the toolchain produced by coreboot-sdk does not include little
endian libraries so it is not possible to build LE image even when that
configuration is changed.
This patch changes byte order definition which is required for proper work
of functions that deal with endianness, like read_{le,be}*() or
{le,be}*toh().
It also revealed bugs related to the endianness on BE targets that are
addressed in the following patches.
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Change-Id: Id31328a832d11db20822733304b0ae477e858d25
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The second generation EFS (offset 0x24[0]=0) uses
"binary relative" offsets and not "x86 physical
MMIO address" like gen1.
Chips like Cezanne can run in both cases, so no problem
comes up so far.
BUG=b:188754219
Test=Majolica (Cezanne)
Change-Id: I3a54f8ce5004915a7fa407dcd7d59a64d88aad0d
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Create the redrix variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:192052098
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_REDRIX
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I4cfa0bd84e1ba9f8140f95d18a6da960da8124ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Update Power Limit2 (PL2) minimum value to the same as maximum value.
DTT does not throttle PL2, so this minimum value change here does not
impact any existing behavior on the system.
BUG=None
BRANCH=None
TEST=Build and test on tglrvp system
Change-Id: I6bbbfa8e43a241df721b91425294983c1d561f2c
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Coverity detects dereference pointers req and res that are NULL when
calling the pmc_send_ipc_cmd function. This change prevents NULL
pointers dereference.
Found-by: Coverity CID 1458077, 1458078
TEST=None
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I151157e7a9a90c43075f431933ac44f29fd25127
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Configure I2C high / low time in the device tree to ensure I2C
CLK runs accurately between 380 kHz and 400 kHz.
Measured I2C frequency just as below after tuning:
touchpad:390.4 kHz
BUG=b:192601250
BRANCH=dedede
TEST=Build and check after tuning I2C clock is between 380 kHz and 400 kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ibe1603a48a3e841b6a50aa0c703697ec615b2854
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
There is a 16 MB flash chip on mc_ehl. Set the ROM size accordingly and
provide a flashmap for partitioning. Select the used flashmap on variant
level to allow different layouts for different variants.
Change-Id: I694729ad98f91e27308220903c49e7cb7fc436b4
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Currently ifdtool breaks the descriptor because it treats it as IFDv1.
This change adds it to the list of IFDv2 platforms.
Fixes boot for X11SSH-LN4F.
Fixes: 8c082e5fef ("util/ifdtool: Use -p platform name to detect IFDv2 platform and chipset")
Change-Id: I3f92b090e929336b5c18b442d1504ee1000f5594
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56070
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In x86_64, the first function parameter is passed in rdi register, and
the 32-bit code after exiting long mode reads the resume vector in
4(%esp), so it's needed to save the resume vector from rdi to 4(%rsp).
Also note that the function attribute "regparm" only works on x86-32
targets according to the GCC manual, so "asmlinkage" doesn't change
the ABI of an x86_64 function.
Tested on HP EliteBook 2560p. The laptop can resume from S3 in x86_64
mode after this change.
Change-Id: I45f2678071b2511c0af5dce9d9b73ac70dfd7252
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55947
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The pointer to the header has a x86 top mmaped address even though the
boot medium is not mapped that way. If no pointer is used to find the
header FMAP is needed. If FMAP is used anyway there is no need for a
cbfs master header.
Change-Id: I6d693bdd4ddaf4c9b3cffb4ea9879c761200aca9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Relying on the implicit defaults for these settings can cause issues in
the future. For example, commit 8cc4c5a1e7
(config.dell_optiplex_9010_sff: Specify board model) was done to prevent
a build failure when adding support for other Dell mainboards which make
the default board change.
Change-Id: Ie0da6254def8b38e9fb053fc7d530dfb46760861
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56079
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allow hot plug devices to subscribe to IOMMU services. Currently the
IOMMU end range is limited to device B:0 D:1f F:6. This prevents the
devices on bus 1 and higher to subscribe to IOMMU services. As per AMD
IOMMU spec v3 section 5.2.2.1 all possible device IDs must be defined,
whether the device ID is actually populated or not. Device entries are
used to report ranges when hot-plug and SR-IOV devices are possible.
With this change the hot plug devices can now bind to IOMMU services
(as tested on kernel v5.4), and below errors are not seen in dmesg.
AMD-Vi: Event logged [IO_PAGE_FAULT device=04:00.3 domain=0x0000]
AMD-Vi: Event logged [IO_PAGE_FAULT device=05:00.0 domain=0x0000]
AMD-Vi: Event logged [IO_PAGE_FAULT device=04:00.4 domain=0x0000]
TEST= Verify dGPU can enumerate on hotplug. No IO page fault errors seen.
The hot plug devices can successfully bind to IOMMU services in
kernel.
Signed-off-by: Aamir Bohra <aamirbohra@gmail.com>
Change-Id: I256c0f8032662674a4d75746de49c250e341c579
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55816
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: ritul guru <ritul.bits@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a new mainboard called mc_ehl which is based on Intel's
'elkhartlake_crb'. This commit simply copies the mainboard directory and
adjusts the naming to match the new board's name. Follow-up commits will
introduce the needed changes for the new mainboard.
Change-Id: Ia7c0616098046d975aa698910ac81f435d7882cb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
This change updates device tree to enable SSDT generation for
world facing camera and user facing camera for ADLRVP.
Also reverts DSDT changes related to both camera.
TEST=Build and Boot aldrvp check i2c enumeration and output of media-ctl
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I39f82dc9eb91496d80479ae3f59ca5e03402a599
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This change updates device tree to enable SSDT generation for
world facing camera and user facing camera for ADLRVP.
Also reverts DSDT changes related to both camera.
TEST=Build and Boot aldrvp check i2c enumeration and output of media-ctl
Compared SSDT with this patch against DSDT without this patch, they are same
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I08834bbcf80dc46737de07f69a2402ed6bf93d4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Redirect stdout and stderr from grep to check for unknown timestamps,
when no timestamps are stored, which is already logged earlier.
Failed to run "/root/coreboot/util/cbmem/cbmem -t", ignoring
Getting remote dmesg
grep: /tmp/coreboot_board_status.dXmbUIBP/emulation/qemu-i440fx/4.14-876-gdb28040ee1/2021-07-02T23_14_33Z/coreboot_timestamps.txt: No such file or directory
Change-Id: Ib5400d4bd17e957b4cc1bf75bbd332d60ad226f5
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The caller is already passing the address to the required LTE reset and
enable GPIO. During memcpy, the address to that pointer is used which
will lead to copying undefined data. Fix the pointer/address used in
memcpy.
BUG=None
BRANCH=dedede
TEST=Build Kracko, Drawcia and Metaknight mainboards which use this
function.
Change-Id: I79d6d9af03acd59ab5e1cd7df97bf451011dfeaa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Found-by: Coverity CID 1458053, 1458054.
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56046
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch sets the optimized FIVR configuration for adlrvp cutomized
based on the pnp measurements to achieve the better power savings in
sleep states.
* Enable the external V1p05, Vnn, VnnSx rails in S0i1, S0i2, S0i3, S3,
S4, S5 states.
* Update the supported voltage states.
* Set the ICC max to 500mA for v1p05 and vnn.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I83e6910502d5cf9d4c26fa581272f59ac483ae19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
The brya EC supports S0ix hang detection, but it was not enabled in
coreboot as well, masking that event out of S0ix, therefore add it in to
the EC S0ix wake mask.
TEST=After EC prints "Warning: Detected sleep hang! Waking host up!",
the host actually wakes up
Change-Id: I2c699114abcd9a045a41858c731e4b6fe99d3000
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The -a flag was already implemented, it just wasn't exposed for the
add-payload command.
Setting the alignment of the payload will enable using the SPI DMA
controller to read the payload on AMD devices.
BUG=b:179699789
TEST=cbfstool foo.bin add-payload -a 64 ...
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9f4aea5f0cbeaa8e761212041099b37f4718ac39
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
We are currently reading the uCode for each CPU. This is unnecessary
since the uCode never changes.
BUG=b:177909625
TEST=Boot guybrush and see "microcode: being updated to patch id" for
each CPU. I no longer see CBFS access for each CPU. This drops device
initialization time by 32 ms.
Also boot Ezkinil and verify microcode was also updated.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I98b9d4ce8290a1f08063176809e903e671663208
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This is a copy of mmap_boot.c and mem_rdev_ro_ops. I split it up so it
was easier to review.
The next patches will add support for the SPI DMA controller. This will
provide a minor speed up vs using mmap reads. It will also provide the
facilities to perform asynchronous SPI loading.
BUG=b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id26e2a69601d0f31e256d0010008904a447c8e21
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
In order to disable X86_TOP4G_BOOTMEDIA_MAP it requires the definition
to be overridden. This makes it a little less ergonomic to use. Instead
introduce the inverse option that can be selected. I chose to leave
X86_TOP4G_BOOTMEDIA_MAP since it keeps the Makefiles simple.
BUG=b:179699789
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I65bbc118bde88687a7d7749c87acf1cbdc56a269
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Introduce `USE_EXP_X86_64_SUPPORT` in `src/arch/x86/Kconfig` and guard
it with `HAVE_EXP_X86_64_SUPPORT`. Replace the per-CPU implementations
of the same functionality with the newly-added Kconfig options. Update
documentation and the config file for QEMU accordingly.
Change-Id: I550216fd2a8323342d6b605306b0b95ffd5dcd1c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Introduce the `ARCH_ALL_STAGES_X86` Kconfig symbol to automatically
select the per-stage arch options. Subsequent commits will leverage
this to allow choosing between 32-bit and 64-bit coreboot where all
stages are x86. AMD Picasso and AMD Cezanne are the only exceptions
to this rule: they disable `ARCH_ALL_STAGES_X86` and explicitly set
the per-stage arch options accordingly.
Change-Id: Ia2ddbae8c0dfb5301352d725032f6ebd370428c9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add SPD support to eldrid for DDR4 memory part MT40A512M16TB-062E:R.
Eldrid should use DRAM_ID strap ID 0 (0000) on SKUs populated
with MT40A512M16TB-062E:R DDR4 memory parts.
BUG=b:192380070
TEST="FW_NAME=eldrid emerge-volteer coreboot" and verify it builds
successfully.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I4d07727c9c41bf494fbef373abce0ac1fc65c316
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55983
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to detect USB Type C device port as Super Speed, we need to set
corresponding bit in UPD UsbTcPortEn. This patch will use device path
to determine which port should be enabled.
BUG=b:184324979
Test=Boot board, USB Type C must be functional and operate at Super Speed.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I7da63f21d51889a888699540f780cb26b480c26d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Since bootmem is not available in romstage, calls to bootmem APIs need
to be compile-time eliminated in order to avoid linker error:
undefined reference to `bootmem_region_targets_type
BUG=None
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_HEROBRINE -x -a -B
cherry-picked on top of CB:49392 and verified successful
compilation.
Change-Id: I8dfa2f2079a9a2859114c53c22bf7ef466ac2ad9
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55865
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently the flow for opregion init is as below:
1. Allocate memory for opregion first (cbmem_add(opregion))
2. Check if VBT size > 6 KiB (this requires extended VBT support)
3. In case of extended VBT requirement, we allocate another chunk
of memory which is equal to size of VBT (cbmem_add(extended_vbt))
4. Pass physical address pointer to OS via RVDA
We can optimize the above flow to allocate single chunk of memory by
checking VBT size in earlier step. The new optimized flow for opregion
init is as below:
1. Check if VBT size > 6 KiB (this requires extended VBT support)
2. In case of extended VBT requirement, total memory to be allocated
is calculated as sizeof(opregion) + sizeof (extended_vbt)
In case where VBT size is < 6 KiB, total memory requirement would
be equal to sizeof(opregion)
3. Based on above calculation, allocate single chunk of memory based on
total size.
This will also be helpful for the case of virtualization where guest
users don't have access to physical address and when it needs relative
address of VBT compared to absolute address.
In case of opregion 2.1 spec, we need to pass relative address of
VBT from opregion base in RVDA. This optimization will help in meeting
this requirement since relative address of extended VBT is easy to get.
This change will ensure that it meets opregion specification
requirement and will be compatible with future versions as well.
BUG=b:190019970
BRANCH=None
TEST=check the address of extended VBT region and address is coming
correctly.
Change-Id: Ic0e255df63145409096b0b9312c6c51c05f49931
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This adds OEM variables feature under DPTF as per BWG doc #541817. Using
this, platform vendors can expose an array of OEM-specific values as OEM
variables to be used in determining DPTF policy. These are obtained via
the ODVP method, and then simply exposed under sysfs. In addition, these
gets updated when a notification is received or when the DPTF policy is
changed by userspace.
BRANCH=None
BUG=b:187253038
TEST=Built and tested on dedede board
Change-Id: Iaf3cf7b40e9a441b41d0c659d76895a58669c2fb
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tidy up the code that programs the PAM (Programmable Attribute Map)
registers. Introduce the `D0F0_PAM` macro and use it to replace the
magic `0x59` and `0x5a` values in the code. Adjust the range of the
for-loop to work with the `D0F0_PAM` macro, and properly indent the
loop's body.
Change-Id: I9036425d726ffb69737ea6ed36c7a8f61d9d040a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Create the cappy2 variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:192035460
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CAPPY2
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I772801152b9ca9c2c6afe76a353cb2b62d6210ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add LTE modem to devicetree.
Configure GPIO control for LTE modem by fw_config.
Update LTE USB port configuration at run-time after probing FW_CONFIG.
By default the concerned USB port takes the Type-A port configuration.
BUG=b:186393848
TEST=Build image and check with command modem status
Change-Id: I20450ae37e5047dba67211316515994bd2a09600
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Update LTE USB port configuration at run-time after probing FW_CONFIG.
By default the concerned USB port takes the Type-A port configuration.
BUG=b:178092096
BRANCH=dedede
TEST=Build and boot to OS to check LTE by modem status
Change-Id: If12cc29ddda6d5c32c0bda840a3680e7bf932f89
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54671
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
By enabling the flag alderlake platform will use hardware sha
instruction instead of software implementation for sha256.
This will speed up firmware verification especially on low-performance
device.
Change-Id: Ie8ab02360fdceafab257e9a301e6a89d3a22c3ae
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add Kconfig option for VBOOT_X86_SHA256_ACCELERATION, which will
use x86-sha extension for SHA256 instead of software implementation.
TEST=Able to call vb2ex_hwcrypto_digest_init() and perform SHA
using HW crypto engine.
Change-Id: Idc8be8711c69f4ebc489cd37cc3749c0b257c610
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
All SMBIOS `type X` tables start with the same 4-byte header. Add a
struct definition for it, and use it where applicable. The union is
temporary and allows doing the necessary changes in smaller commits.
Change-Id: Ibd9a80010f83fd7ebefc014b981d430f5723808c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reduce the scope or remove some `len` variables. This is done to ease
replacing `sizeof` on struct types in a follow-up commit, by ensuring
that all to-be-replaced appearances follow the variable declarations.
Change-Id: Ied38fcaf87ef5b1e4f93076b4ba2898ad1f98a72
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This is done to ensure the CSE will not execute any pre-boot commands
after it receives this command. Verified EOP and error recovery sequence
from Intel doc#612229
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iae6b2eac11c065749e57c5337d81ed20044fc903
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is done to ensure the CSE will not execute any pre-boot commands
after it receives this command. Verified EOP and error recovery sequence
from Intel doc#627331.
TEST=on brya, autotest firmware_CheckEOPState confirms ME is in
post-boot state
Change-Id: Iee8c29f81d5d04852ae3f16dc8a9ff0fa59f056a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds functionality to attempt to allow booting in a secure
configuration (albeit with potentially reduced functionality) when the
CSE EOP message fails in any way. These steps come from the CSME BWG
(13.5, 15.0, 16.), and tell the CSE to disable the MEI bus, which
disables further communication from the host. This is followed by
requesting the PMC to disable the MEI devices. If these steps are
successful, then the boot firmware can continue to boot to the
OS. Otherwise, die() is called, prefering not to boot over leaving the
insecure MEI bus available.
BUG=b:191362590
TEST=Set FSP UPD to disable sending EOP; called this function from a
BS_PAYLOAD_LOAD, ON_ENTRY entry; observed that with just
cse_mei_bus_disable() called, Linux can no longer communicate over MEI:
[ 16.198759] mei_me 0000:00:16.0: wait hw ready failed
[ 16.204488] mei_me 0000:00:16.0: hw_start failed ret = -62
[ 16.210804] mei_me 0000:00:16.0: H_RST is set = 0x80000031
[ 18.245909] mei_me 0000:00:16.0: wait hw ready failed
[ 18.251601] mei_me 0000:00:16.0: hw_start failed ret = -62
[ 18.257785] mei_me 0000:00:16.0: reset: reached maximal consecutive..
[ 18.267622] mei_me 0000:00:16.0: reset failed ret = -19
[ 18.273580] mei_me 0000:00:16.0: link layer initialization failed.
[ 18.280521] mei_me 0000:00:16.0: init hw failure.
[ 18.285880] mei_me 0000:00:16.0: initialization failed.
Calling both error recovery functions causes all of the slot 16 devices
to fail to enumerate in the OS
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I06abf36a9d9d8a5f2afba6002dd5695dd2107db1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55675
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable PCH GBE with following changes:
1. Configure PCH GBE related FSP UPD flags
2. Use EHL own GBE ACPI instead of common code version due to
different B:D.F from the usual GBE
3. Add kconfig PMC_EPOC to use the PMC XTAL read function
Due to EHL GBE comes with time sensitive networking (TSN)
capability integrated, EHL FSP is using 'PchTsn' instead of the
usual 'PchLan' naming convention across the board.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I6b0108e892064e804693a34e360034ae7dbee68f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
1. Remove 'PCH_EPOC_XTAL_FREQ(__epoc)' macro since it only be used
in 1 place.
2. Transform macro into more readable C code.
3. Add additional case check to make sure the returned value is
defined in the 'pch_pmc_xtal' enum.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: If57a99bf8e837a6eb8f225297399b1f5363cfa85
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Move PMC EPOC related code to intel/common/block because it is
generic for most Intel platforms and ADL, TGL & EHL use it.
Add a kconfig 'PMC_EPOC' to guard this common EPOC code.
The PMC EPOC register indicates which external crystal oscillator is
connected to the PCH. This frequency is important for determining the
IP clock of internal PCH devices.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ib5fd3c4a648964678ee40ed0f60ca10fe7953f56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change syncs the coreboot version of google ec_commands.h with the
ec_commands.h from the google ec repository. This is a straight copy
except for the the copyright header.
BUG=b:184074997
TEST=Build and boot guybrush
BRANCH=None
Change-Id: I095c3316d720328cb7b8dd1b72ffc108208b14bd
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
To generalise the choice of 32-bit or 64-bit coreboot on x86 hardware,
have platforms select `ARCH_X86` directly instead of through per-stage
Kconfig options, effectively reversing the dependency order.
Change-Id: If15436817ba664398055e9efc6c7c656de3bf3e4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The results of the PCI IRQ assignments are used in several places, so
it makes for a nicer API to cache the results and provide simpler
functions for the SoCs to call.
BUG=b:130217151, b:171580862, b:176858827
Change-Id: Id79eae3f2360cd64f66e7f53e1d78a23cfe5e9df
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55825
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Because the FSP interface for PCI IRQs only includes the PCH devices,
this function is the complement to that, taking the list of irq entries,
and programming the PCI_INTERRUPT_LINE registers.
BUG=b:130217151, b:171580862, b:176858827
TEST=boot brya with patch train, verify with `lspci -vvv` that for all
the north PCI devices, their IRQ was either the one programmed by this
function, or an MSI was used.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I81cf7b25f115e41deb25767669b5466b5712b177
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55817
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Intel FSP provides a default set of IO-APIC IRQs for PCI devices, if
the DevIntConfigPtr UPD is not filled in. However, the FSP has a list of
rules that the input IRQ table must conform to:
1) One entry per slot/function
2) Functions using PIRQs must use IOxAPIC IRQs 16-23
3) Single-function devices must use INTA
4) Each slot must have consistent INTx<->PIRQy mappings
5) Some functions have special interrupt pin requirements
6) PCI Express RPs must be assigned in a special way (FIXED_INT_PIN)
7) Some functions require a unique IRQ number
8) PCI functions must avoid sharing an IRQ with a GPIO pad which routes
its IRQ through IO-APIC.
Since the FSP has no visibility into the actual GPIOs used on the board
when GpioOverride is selected, IRQ conflicts can occur between PCI
devices and GPIOs. This patch gives SoC code the ability to generate a
table of PCI IRQs that will meet the BWG/FSP rules and also not conflict
with GPIO IRQs.
BUG=b:130217151, b:171580862, b:176858827
TEST=Boot with patch series on volteer, verify IO-APIC IRQs in
`/proc/interrupts` match what is expected. No `GSI INT` or
`could not derive routing` messages seen in `dmesg` output.
Verified TPM, touchpad, touchscreen IRQs all function as expected.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I0c22a08ce589fa80d0bb1e637422304a3af2045c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49408
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To set the Fibocom 850-GL module to USB mode, it needs to be disabled
when PCIe training happens, or it will automatically switch to PCIe
mode. This patch makes sure it's shut down when training happens in
FSP-M. It will be brought up in ramstage and will be available for USB
enumeration later.
BUG=b:187316460
TEST=Run lsusb from the OS and see that the Fibocom module is present
on USB.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I153eb6cd7c3a0e2cc3b71c99f76db3e565173cfe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This configures the romstage portion of the PCIe GPIOs in the correct
sequence to meet the power-on timings.
The PCIe_RST line is anded with the Aux reset lines, so to take the PCIe
devices out of reset, both need to be brought hign.
BUG=b:184796302, b:184598323
TEST=Verify timings between GPIO init sections. All available modules
are present after training.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ib1990bba31c84827467d4ff8a15f1e0682501e70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54741
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This configures the bootblock portion of the PCIe GPIOs in the correct
sequence to meet the power-on timings.
Setting the PCIE Reset happens in coreboot instead of in the FSP.
The Aux reset lines are anded with the PCIe RST line, so both have
to be brought up together. On v1 of guybrush, the PCIe reset line
also resets EC communication, so it must be brought up immediately on
that version.
BUG=b:184796302, b:184598323
TEST=Verify timings between GPIO init sections. All available modules
are present after training.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I2d0b812b654b0cd317a2c8c1ce554e850c96be44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add configs for Herobrine variants. Also enable ec sw sync as this
should not be disabled by default.
BUG=b:182963902
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_SENOR -x -a -B
./util/abuild/abuild -p none -t GOOGLE_PIGLIN -x -a -B
Change-Id: Ide4e375aa0236dce65a954a2f68455d05fa841eb
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
When initializing eSPI early, guybrush has requirements to configure the
bus properly. Those are normally run in bootblock_mainboard_early_init,
but when setting up eSPI early, those have not run yet.
BUG=192100564
TEST=Build along with previous patch, eSPI works on guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ifec6113d48aea0bb5efe47909e4faf0161148a99
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55864
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To reduce power load, set unused GPIOs to NC and close
unused interface in devicetree. GPIOs and
interfaces are as below:
GPIO: GPP_C18/C19/D12/D14/D15/D19/D20/D21/E00/E02/H06/H07
Interface: I2C1/I2C3/I2C5
USB: port2_3/2_4/2_6
BUG=b:185044041
BRANCH=dedede
TEST=Built bios and test, it reduces power load without affecting
device function.
Change-Id: Ib5999f0e129bf3e660fe293eda7af3e8e1426151
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ben Kao <ben.kao@intel.com>
The `soc_read_pmc_base()` function returns an `uintptr_t`, which is then
casted to a pointer type for use with `read32()` and/or `write32()`. But
since commit b324df6a54 (arch/x86: Provide
readXp/writeXp helpers in arch/mmio.h), the `read32p()` and `write32p()`
functions live in `arch/mmio.h`. These functions use the `uintptr_t type
for the address parameter instead of a pointer type, and using them with
the `soc_read_pmc_base()` function allows dropping the casts to pointer.
Change-Id: Iaf16e6f23d139e6f79360d9a29576406b7b15b07
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Introduce a macro retry(attempts, condition, expr) for retrying a
condition, which is extensively used in coreboot.
Example usage:
if (!retry(3, read32(REG) == 0, mdelay(1))
printk(BIOS_ERR, "Error waiting for REG to be 0\n");
BUG=none
TEST=make tests/commonlib/bsd/helpers-test
TEST=emerge-cherry coreboot
BRANCH=none
Change-Id: I421e4dcab949616bd68b3a14231da744b9f74eeb
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Vboot's Makefile is controlled by a ${DEBUG} environment variable.
As the name is very generic, it may be set by accident without any
intention to change the build. Having it set would break reproduci-
bility at least but it also turns out that the hostlib build would
be incomplete so that linking cbfstool fails due to internal calls
to vb2api_fail() which is not built in.
Change-Id: I2a9eb9a645c70451a320c455b8f24bfed197117c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
FirmwareVersionInfoHob.h is removed in JSL FSP v2376 so
remove it from Jasper Lake vendorcode.
BUG=b:153038236
BRANCH=None
TEST=Verify JSLRVP build with all the patch in relation chain
and verify the version output prints no junk data observed.
couple of lines from logs are as below.
Display FSP Version Info HOB
Reference Code - CPU = 8.7.16.10
uCode Version = 0.0.0.1
Change-Id: Iad0429630665f50dbc1541487c9061dd1a19907c
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45908
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Select DISPLAY_FSP_VERSION_INFO_2 for Jasper Lake soc.
BUG=b:153038236
BRANCH=None
TEST=Verify JSLRVP build with all the patch in relation chain
and verify the version output prints no junk data observed.
couple of lines from logs are as below.
Display FSP Version Info HOB
Reference Code - CPU = 8.7.16.10
uCode Version = 0.0.0.1
Change-Id: If68b704c4304357b0046a510545fc213d7ed5887
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45907
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:55452 uses FMAP instead of "cbfs master header".
The flash size statement in vboot-rw.fmd does not contain the start
address, resulting in a non-booting system.
Add start address to FLASH statement.
BUG = N/A
TEST = Boot Facebook FBG1701
Change-Id: Id05ad33babb416a37c657b25cdb1e98d47c1a56d
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
0xf7f000 - 0x1000 = 0xf7e000, not 0xf6f000.
This fixes build failure when selecting the option to validate the
layout using the flash descriptor (CONFIG_VALIDATE_INTEL_DESCRIPTOR)
Test: build google/casta successfully with IFD validation selected
Change-Id: I6df67f76f5d766a9f4f85ffc3e1f0de4a241f509
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55815
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `xdci_can_enable()` function is called earlier to configure FSP-S
UPDs. If it returned false, then the xDCI device will be disabled and
the second `xdci_can_enable()` call will never be evaluated.
Change-Id: I4bd08e3194ffccc79c8feaf8f34b2bb4077f760a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55789
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The null-termination of `filetypes` was added after the code was
written, obviously resulting in NULL dereferences. As some more
code has grown around the termination, it's hard to revert the
regression, so let's update the code that still used the array
length.
This fixes commit 7f5f9331d1 (util/cbfstool: fix buffer over-read)
which actually did fix something, but only one path while it broke
two others. We should be careful with fixes, they can always break
something else. Especially when a dumb tool triggered the patching
it seems likely that fewer people looked into related code.
Change-Id: If2ece1f5ad62952ed2e57769702e318ba5468f0c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Error Could not add [key.vbpubk]: too big occurs, when Eltan verified boot is enabled.
Update value of VENDORCODE_ELTAN_VBOOT_KEY_LOCATION.
BUG = N/A
TEST = Boot Facebook FBG1701 with Eltan verified boot enabled.
Change-Id: I1faecd189915985df633ac74627fd872ce8867f0
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
BUG=b:191213716
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682 or DA7219 then check
whether device tree is updated correspondingly by disabling unselected
one.
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I2d5738442d2c173fd5b4802d8b5dff76b428c6f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55564
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update MdePkg/Include/IndustryStandard/SmBios.h to avoid compilation
errors through safeguarding definitions with DISPLAY_FSP_VERSION_INFO_2
Kconfig.
BUG=b:153038236
BRANCH=None
TEST=Verify JSLRVP build with all the patches in relation chain
and verify the version output prints no junk data observed.
Couple of lines from logs are as below.
Display FSP Version Info HOB
Reference Code - CPU = 8.7.16.10
uCode Version = 0.0.0.1
Change-Id: I9698861be1f969ddca7f171767a54ac486502c74
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45906
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The CSE expects the boot firmware to send it an End-of-Post message
before loading the OS. This is a security feature, and is done to ensure
that the CSE will no longer perform certain sensitive commands that are
not intended to be exposed to the OS.
If processing the EOP message fails in any way on a ChromeOS build, (and
not already in recovery mode), recovery mode will be triggered,
otherwise the CSME BWG will be followed, which is in the following
commit.
BUG=b:191362590
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6f667905f759cc2337daca4cc6e09694e68ab7e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
To avoid from using same the name AMDI5682 as Zork, changing to use
AMDI1019. The corresponding kernel change is on CL:2929864
BUG=b:189297564
TEST=Audio works with the corresponding kernel change.
Cq-Depend: chromium:2929864
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@google.com>
Change-Id: Ie89302f3b6cd3edb8253b909fde4722c2ea1e102
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55508
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This motherboard is almost identical to the ASUS P5QL PRO,
with the only noticeable difference being that the ASUS P5Q SE
has a P45 MCH while the P5QL PRO has a P43 MCH. Few changes were
required.
Signed-off-by: Hunter Sell <alicelyralain@gmail.com>
Change-Id: I36612bac16a79f05f3fe57e535e4ba3c73790a86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add Makefile.inc to include three generic LPDDR4 SPDs for the following
parts for Gimble:
DRAM Part Name DRAM ID to assign
MT53E512M32D2NP-046 WT:E 0 (0000)
H9HCNNNCPMMLXR-NEE 1 (0001)
H9HCNNNBKMMLXR-NEE 0 (0000)
BUG=b:191574298
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I60f95ac5ed7f3134882f6580335ec33632676796
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This patch updates mainboard_memory_init_params() function argument from
FSPM_UPD to FSP_M_CONFIG. Ideally mainboard_memory_init_params()
function don't need to override anything other than FSP_M_CONFIG UPDs
hence passing config block alone rather passing entire FSP-M UPD
structure.
Change-Id: I238870478a1427918abf888d71ba9c9fa80d3427
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch create separate helper functions to fill-in required
FSP-S UPDs as per IP initialization categories.
This would help to increase the code readability and in future
meaningful addition of FSP-S UPDs is possible rather adding UPDs randomly.
TEST=FSP-S UPD dump shows no change without and with this code change.
Change-Id: Iba51aebc74456449e24e51e2f309f14f951464a0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55233
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Temporarily set eSPI mux in verstage_mainboard_early_init.
Ideally cezanne code should have common function to do this and
mb-specific code would just call it, but for now PCI access doesn't work
in the PSP so we can't do it.
AMD team confirmed that the current PSP doesn't configure LPC so we
don't have to disable LPC when configuring eSPI mux so we can
temporarliy skip the LPC part here.
BUG=b:183149183
TEST=boot guybrush with psp_verstage
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I8317409fa5efd1adffc184d75affbb4d305183f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
In order to enable ACP DMIC hardware runtime detection, indicate that
ACP DMIC is present.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the _WOV ACPI method
is populated in the ACP device.
Change-Id: I9a53d158ed08a6b46c29bcb8fe3a2a0d108bd6cd
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55030
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to support Audio Co-processor (ACP) DMIC hardware runtime
detection on the platform, ACPI _WOV method is populated on the
concerned ACP device. This method returns the ACPI Integer value as 1
if ACP DMIC exists on the platform.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the _WOV ACPI method
is populated under the scope of ACP device.
Scope (\_SB.PCI0.GP41.ACPD)
{
Method (_WOV, 0, NotSerialized)
{
Return (One)
}
}
Change-Id: Ide84f45f5ea2ae42d5efe71ac6d1595886157045
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55029
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If the NO_EARLY_BOOTBLOCK_POSTCODES config option is enabled, configure
eSPI as early as possible in the x86 boot sequence.
We found that there are situations that can cause the system to hang if
there are any port80h postcodes sent out before eSPI is initialized.
BUG=b:191370340
TEST=Build & Boot with and without NO_EARLY_BOOTBLOCK_POSTCODES enabled.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I0badb1c529e96ee4f81134287db53ce32473de6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55732
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The original reason the BERT table was moved out of CBMEM was because
the OS was not able to access the region. This happened because the
CBMEM region was marked as type 16 in the e820 table. The OS isn't aware
of this type, so it prevents any drivers from accessing it. Depthcharge
now correctly labels the CBMEM region as reserved in the e820 table so
we can move the BERT table into CBMEM.
TEST=BERT ACPI table generation still works on AMD/Mandolin with SeaBIOS
as payload and BERT region inside CBMEM is inside a BIOS-e820 reserved
range. BERT generation also works on Zork with depthcharge.
Link: https://crrev.com/c/2939677
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie640e91c19ae5f9b275cc333284b4be34211fbf6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Config items depends on USE_VENDORCODE_ELTAN but are VBOOT specific.
Correct dependency of these items on VENDORCODE_ELTAN_VBOOT.
BUG = NA
TEST = Boot facebook FBG-1701 with possible combinations of Eltan
security.
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Change-Id: Icd1c3e5c70ca562190308752f45aac734826649a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52132
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use devfn_disable() for disabling a PCI device rather than
using `dev->enabled = 0`.
Also, use is_devfn_enabled() to get the device current state prior
updating the FSP-S UPD for XDCI.
TEST=FSP-S disabled XDCI when `xdci_can_enable` returns 0 and XDCI
is disabled at PCI enumeration `PCI: 00:14.1: enabled 0`.
Change-Id: I5e10e5d0b80986e1e73573a86a957985840fe0b3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55727
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use devfn_disable() for disabling a PCI device rather than
using `dev->enabled = 0`.
Also, use is_devfn_enabled() to get the device current state prior
updating the FSP-S UPD for XDCI.
TEST=FSP-S disabled XDCI when `xdci_can_enable` returns 0 and XDCI
is disabled at PCI enumeration `PCI: 00:14.1: enabled 0`.
Change-Id: I64ab77bc49d93aca1da0126d849e69ff75b182a3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55726
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use devfn_disable() for disabling a PCI device rather than
using `dev->enabled = 0`.
Also, use is_devfn_enabled() to get the device current state prior
updating the FSP-S UPD for XDCI.
TEST=FSP-S disabled XDCI when `xdci_can_enable` returns 0 and XDCI
is disabled at PCI enumeration `PCI: 00:14.1: enabled 0`.
Change-Id: I8ca0813e18da0f95eb9293b6d0bbdf933a1e7039
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55725
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use devfn_disable() for disabling a PCI device rather than
using `dev->enabled = 0`.
Also, use is_devfn_enabled() to get the device current state prior
updating the FSP-S UPD for XDCI.
TEST=FSP-S disabled XDCI when `xdci_can_enable` returns 0 and XDCI
is disabled at PCI enumeration `PCI: 00:14.1: enabled 0`.
Change-Id: I568cd39792eba1bbace4901e96d708d80f73c60a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55724
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use devfn_disable() for disabling a PCI device rather than
using `dev->enabled = 0`.
Also, use is_devfn_enabled() to get the device current state prior
updating the FSP-S UPD for XDCI.
TEST=FSP-S disabled XDCI when `xdci_can_enable` returns 0 and XDCI
is disabled at PCI enumeration `PCI: 00:14.1: enabled 0`.
Change-Id: I038e43deead70d598cf26f320dd9993f17591b88
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55723
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use devfn_disable() for disabling a PCI device rather than
using `dev->enabled = 0`.
Also, use is_devfn_enabled() to get the device current state prior
updating the FSP-S UPD for XDCI.
TEST=FSP-S disabled XDCI when `xdci_can_enable` returns 0 and XDCI
is disabled at PCI enumeration `PCI: 00:14.1: enabled 0`.
Change-Id: I0e400ded7ba268a5f289b0ac568598e0dad1899a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55722
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Replace all pcidev_path_on_root() and is_dev_enabled() functions
combination with is_devfn_enabled().
2. Remove unused local variable of device structure type
(struct device *).
3. Replace pcidev_path_on_root() and dev->enabled check with
is_devfn_enabled() call.
4. Leave SATA, eMMC controller FSP UPDs at default state if
controller is not enabled and FSP UPDs are set to disable.
TEST=Able to build and boot without any regression seen on ICLRVP.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Id6861af3b5d1ce4f44b6d2109301bd4f5857f324
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Our existing native function gpio configuration macro (PAD_NF) only sets
the pull. For PCIe reset, we now need to be able to set it to its
native function (PCIE_RST_L), and drive it low, then high.
BUG=b:182805349
TEST=Configure GPIO, see correct behavior.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I636371517c99f94f76834abc4575795d51aa0368
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55652
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PSP_Verstage will enable eSPI early in the boot sequence. If the
platform isn't using psp_verstage, the system can hang on the first
port 80h postcode that comes out because they aren't routed to an
active device until eSPI is configured.
BUG=b:191370340
TEST=Build without PSP_Verstage, verify system doesn't hang.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I37fbb251cd79609b856c4480ca29ce94b08897d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55738
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
One of the reason FSP-T support had to be kept in place was for
Intel Bootguard. This now works with native CAR code, so there is no
reason to keep FSP-T as an option for these platforms.
APL did not even build with FSP_CAR and finding FSP-T using walkcbfs
was only recently fixed using FMAP, so there can be no doubt that this
option was never used with coreboot master.
Change-Id: I0d5844b5a6fd291a13e5f467f4fc682b17eafa63
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Bootguard sets up CAR/NEM on its own so the only thing needed is to
find free MTRRs for our own CAR region and clear that area to fill in
cache lines.
TESTED on prodrive/hermes with bootguard enabled.
Change-Id: Ifac5267f8f4b820a61519fb4a497e2ce7075cc40
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This adds a macro to find an available MTRR(s) to set up CAR.
This added complexity is not required on bootpaths without bootguard
but with bootguard MTRR's have already been set up by the ACM so
we need to figure out at runtime which ones are available.
Change-Id: I7d5442c75464cfb2b3611c63a472c8ee521c014d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This motherboard is somewhat similar to the p8h61-m_pro, but also different.
It has two exposed RAM slots with a pinout for four, and it's an OEM
variant used in PCs ASUS sold in stores.
Signed-off-by: Hunter Sell <alicelyralain@gmail.com>
Change-Id: Id08349feb0aeaf21406f814f6d19bbe0d9312a4d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Using `config_of(dev)` to access `dev->chip_info` will make coreboot die
if the latter is NULL, which is the case for devices detected at runtime
(i.e. not statically declared in the devicetree). Given that the code is
designed to work when the PEG config is all-zeroes (devicetree default),
dying because `dev->chip_info` is NULL is foolish and unwarranted.
Introduce a helper function that returns a pointer to devicetree config
when available, and otherwise returns a pointer to a zero-filled static
struct. In addition, avoid an out-of-bounds access in the very unlikely
case where the device's function is too large.
Tested on Asrock B85M Pro4, can now boot when `device pci 01.0 on end`
is commented out in its devicetree. Without this commit, it could not.
Change-Id: Ia2d3a03da9eab601fb834b0c51a8a51c9ae14c33
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
PEG bifurcation is strapped to x8/x8 on this board, but only the first
port is used. Disable the PEG device at 00:01.1 because it is unused.
Should fix booting with commit ae999503f6
(nb/intel/haswell/pcie.c: Add missing pre-ASPM init). The `config_of()`
function call added in that commit makes coreboot die if any PEG device
that is enabled by strapping is not present in the devicetree. While it
is true that the PEG code should not use `config_of()`, this PEG device
should still be disabled on this board as it is never used.
Change-Id: I16809e081f9a56ba2f1fdfcb4b8289d75161056b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Máté Kukri <kukri.mate@gmail.com>
Remove some redundant parts of devicetree comments. This used to happen
when using autoport, but has been fixed at some point.
Tested with BUILD_TIMELESS=1, Lenovo T440p remains identical.
Change-Id: Ie24b5430c7771c9ce4dda6c9a10d70ee9000df7c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
An error in script did not set the attribute properly:
- Entry CS0 is not used as sensor, but as ground,
- Entry CS1 is used as the startup sensor.
This fixes a regression caused by commit
689c25b9d6 (drivers/i2c: sx9310: Replace register map with descriptive names)
EQ=b:173341604
BRANCH=volteer
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Change-Id: I92c01209031e9a917d95b1cb2537b0ce7b93e66d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51893
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We moved from gitweb to cgit to gitiles and some of the URL schemes
were lost during the transitions. Update to the gitiles scheme so
board-status links work again.
Change-Id: Id2a840bf89fab172e0eab21e303ac0c4666b6751
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The patch moves CSE Lite RW status check out of CSE RW update logic as
the RW sanity check has to be done irrespective of CSE RW update logic
is enabled or not. If coreboot detects CSE Lite RW status is not good,
the coreboot triggers recovery.
TEST=Verified boot on Brya
Signed-off-by: Sridahr Siricilla <sridhar.siricilla@intel.com>
Change-Id: I582b6cf24f8894c80ab461ca21f7c6e8caa738bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55619
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Pass the info if the non-graphics HD audio controller device is enabled
or disabled in the board's devicetree via a UPD to the FSP so that it
knows if it should enable or disable the corresponding device.
TEST=When adding "device ref hda on end" to the devicetree of
amd/majolica the non-graphics HD Audio controller shows up in lspci and
when that line isn't added the PCIe device doesn't show up.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9f5e164d308906bfc788e5c2674c13c7b2ebf471
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Currently the FSP only has one switch to disable both AHCI controllers.
If at least one of the two AHCI controller devices is enabled in the
board's devicetree, set the SATA enable UPD to 1 and otherwise set it to
0. Setting the UPD value to 0 when both AHCI controllers are disabled
saves around 60ms in boot time.
BUG=b:191385289
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I84e7c8bf2ab08c8254271ddfefd2e4e7d8c2e87b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55669
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use devfn_disable() for disabling a PCI device rather than
using `dev->enabled = 0`.
Also, use is_devfn_enabled() to get the device current state prior
updating the FSP-S UPD for XDCI.
TEST=FSP-S disabled XDCI when `xdci_can_enable` returns 0 and XDCI
is disabled at PCI enumeration `PCI: 00:15.1: enabled 0`.
Change-Id: I449beae59d2f578c027d8110c03fa79f516c3fe9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
On platforms where the boot media can be updated externally, e.g.
using a BMC, add the possibility to enable writes in SMM only. This
allows to protect the BIOS region even without the use of vboot, but
keeps SMMSTORE working for use in payloads. Note that this breaks
flashconsole, since the flash becomes read-only.
Tested on Asrock B85M Pro4 and HP 280 G2, SMM BIOS write protection
works as expected, and SMMSTORE can still be used.
Change-Id: I157db885b5f1d0f74009ede6fb2342b20d9429fa
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Elkhart Lake provides a feature called "In-Band ECC" which uses a piece
of system DRAM to store the ECC information in. There are a few
parameters in FSP-M to set this feature up as needed.
This patch adds code to expose these parameters to the devicetree so
that they can be configured on mainboard level as needed.
Change-Id: I7a4953d7b35277de01daff04211450e3d1bd8103
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55668
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- set subsystem/subvendor ID to Realtek default, as the one dumped
from the vendor UEFI firmware provides no advantages
- Add a codec reset before setting the subvendor ID using the Azalia macro
for consistency with all other Realtek HDA codecs
- disable jack detect for the external mic on the 3.5mm jack, since it's not
currently working, so that the external microphone can be manually selected
Change-Id: Ib0f99e5088973a721c0a295899012c9aea5009cf
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
- set subsystem/subvendor ID to Realtek default, as the one dumped
from the vendor UEFI firmware provides no advantages
- fix the number of verb entries, which excluded the 4 following the
pin configs
- issue the reset *before* setting the subvendor, and use the Azalia macro
- disable jack detect for the 3.5mm jack, both line out and mic, since
it's not currently working, so that the outputs can be manually selected
Change-Id: Icd961c3c5aec23cf61d6a9ad65c603c6dc04697a
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enable FastPkgCRampDisable for all domains, set SlowSlewRate to fast/16
for all domains. This aligns the settings with the Librem 14.
Test: boot Librem Mini v2, observe high frequency acoustic noise reduced.
Change-Id: I10bc2a3e6b631b8c0b430e204f376aa9a81ac683
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Somehow, enabling the notification to the OS driver breaks the
functionality it was meant to enable. Until this can be resolved,
disable the driver notification, so that the key functions as intended.
Test: build/boot librem_bdw and librem_skl boards, verify trackpad
enable toggle via Fn+F1 works properly.
Change-Id: Ic7bdb3154a87c4202b5ee1fd333281ef78db1104
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55657
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CSE error codes may be applicable to move than just CSE Lite SKU errors,
therefore move this enum to the intelblocks/cse.h file so that it can be
used in other CSE-related code. While copying, remove `LITE_SKU` from a few
of the enum values that are not necessarily CSE Lite SKU-specific.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I0351587c67ce12f781c536998ca18a6a804d080a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55672
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ifdtool uses `chipset` information to determine how certain straps
are decoded. This has been used for IFDv1 platforms as well as IFDv2
platforms (CHIPSET_500_600_SERIES_TIGER_ALDER_POINT).
IFDv2 platforms are all expected to pass in `-p` argument to identify
the platform. This platform information can be used to identify the
appropriate chipset information. For IFDv1 since `-p` argument is not
provided, ifdtool needs to use certain fields in the descriptor
(e.g. strap length) for unique identification of IFDv1 chipset.
This change updates `check_ifd_version()` function to:
1. Determine if IFD version is v1 or v2 based on `-p` argument.
If `-p` is not provided, it assumes that the platform is using IFDv1.
2. Based on IFD version, it calls either `ifd2_platform_to_chipset()`
or `ifd1_guess_chipset()` to determine chipset information.
This fixes the issue reported with CB:44815, where ifdtool is unable
to identify Alder Lake chipsets.
BUG=b:153888802
TEST=Able to dump FD contains correctly with platform quirks on Brya Platform.
> ifdtool -d coreboot.rom -p adl
PCH Revision: 500 series Tiger Point/ 600 series Alder Point
Change-Id: I25f69ce775454409974056d8326c02e29038ec8a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54305
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On dedede boards without Cr50, the CrOS Board Info (CBI) EEPROM write
protect signal is decoupled from the hardware write protect signal.
Instead, we'd like for it to mirror the software write protect status.
This commit simply checks the software write protect status of the SPI
flash and sets the CBI EEPROM write protect if it's enabled. To prevent
changing the WP signal at run-time, the GPIO configuration is also
locked down after the level has been set. If HW WP is deasserted, the
CBI EEPROM WP will be deasserted as well.
BUG=b:191189275,b:184592299
BRANCH=None
TEST=Build and flash lalala, disable SW WP by running `flashrom -p host
--wp-disable` from a root shell and verify that the GPIO is asserted
after a reboot. Export the gpio via sysfs and verify that attempting to
change the value of the GPIO is futile. Enable SW WP via `flashrom -p
host --wp-enable` and reboot the DUT. Again, export the GPIO via sysfs
and verify that attempts to change the GPIO value are futile.
localhost ~ # iotools mem_read32 0xfd6e08d0
0x44000200
localhost ~ # cd /sys/class/gpio/
localhost /sys/class/gpio # echo 217 > export
localhost /sys/class/gpio # cd gpio217/
localhost /sys/class/gpio/gpio217 # echo out > direction
localhost /sys/class/gpio/gpio217 # cat value
0
localhost /sys/class/gpio/gpio217 # echo 1 > value
localhost /sys/class/gpio/gpio217 # cat value
1
localhost /sys/class/gpio/gpio217 # iotools mem_read32 0xfd6e08d0
0x44000200
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: Ic103037921ec7d2f96f86178675c11a3a1357d1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This commit adds a method called `mainboard_smi_finalize` which provides
a mechanism for a mainboard to execute some code as part of the finalize
method in the SMM stage before SoC does its finalization.
BUG=b:191189275
BRANCH=None
TEST=Implement `mainboard_smi_finalize` on lalala and verify that the
code executes in SMM.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: If1ee63431e3c2a5831a4656c3a361229acff3f42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This commit simply adds the offset for the PADCFGLOCK register for the
Intel Jasper Lake platform. This enables pads to be locked.
BUG=b:191189275
BRANCH=None
TEST=Enable pad locking on lalala by calling `gpio_lock_pad` and verify
that the pad configuration is locked and cannot be manipulated from the
OS.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: Iccfe536b4a881f081f22bcc258a375caad3ffcb3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55648
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit adds a method for locking a GPIO pad configuration and its
TX state. When the configuration is locked, the following registers
become Read-Only and software writes to these registers have no effect.
Pad Configuration registers
GPI_NMI_EN
GPI_SMI_EN
GPI_GPE_EN
Note that this is only effective if the pad is owned by the host (set in
the PAD_OWN register).
Intel platforms that wish to leverage this function need to define the
PADCFGLOCK offset for their platform.
BUG=b:191189275
BRANCH=None
TEST=With some other code, call gpio_lock_pad() against a pad and verify
that the pad configuration is locked and the state of the pad cannot be
changed from the OS.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: Id3c0da2f6942099c0289ca1e33a33c176f49d380
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Per the Intel External Design Specification (doc #618876), the opcode
for GPIO_LOCK_UNLOCK is 0x13. This commit fixes a bug where the opcode
was defined as 13 decimal instead of hexadecimal. Additionally, it
fixes another issue where the `pcr_execute_sideband_msg()` function
doesn't actually write the data when this opcode is selected.
BUG=b:191189275
BRANCH=None
TEST=With additional code that uses this opcode, verify that the lock
functionality works by locking a pad in firmware and attempting to
modify the configuration of the pad from the OS.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: Ie14fff595474cdfd647c2b36f1eeb5e018f67375
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55556
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:51638 separated Chrome OS NVS from global NVS by allocating it
separately in CBMEM. CNVS is used in depthcharge to fill firmware
information at boot time. Thus, location of CNVS needs to be shared in
coreboot tables for depthcharge to use.
This change adds a new coreboot table tag
`CB_TAG_ACPI_CNVS`/`CB_TAG_ACPI_CNVS`(0x41) which provides the
location of CNVS in CBMEM to payload (depthcharge).
Additionally, CB:51639 refactored device nvs(DNVS) and moved it to the
end of GNVS instead of the fixed offset 0x1000. DNVS is used on older
Intel platforms like baytrail, braswell and broadwell and depthcharge
fills this at boot time as well. Since DNVS is no longer used on any
new platforms, this information is not passed in coreboot
tables. Instead depthcharge is being updated to use statically defined
offsets for DNVS.
BUG=b:191324611, b:191324611
TEST=Verified that `crossystem fwid` which reads fwid information from
CNVS is reported correctly on brya.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I3815d5ecb5f0b534ead61836c2d275083e397ff0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55665
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using existing defines instead of magic values improves readability of
the code. Also add comments to the MADT IRQ overrides to make it clearer
what those actually do.
TEST=Timeless build results in identical binary for amd/gardenia
(Stoneyridge), amd/mandolin (Picasso) and amd/majolica (Cezanne)
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I224ffbe8eb65bcdd5fc70c0ff8b15d55b3f6be01
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55613
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_A19(DP_HPD1) and GPP_A20(DP_HPD2) were configured native function
(NF1), this causes redundancy with legacy HPD interruption.
This change configures GPP_A19 and GPP_A20 to be no connection and
disables DdiPort1Hpd and DdiPort2Hpd.
BUG=None
TEST=Boot to kernel and verified no kernel HPD pins assertion message.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I80ef40a1aca19cd6ad56219175d2fd40890a393d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sanrio Alvares <sanrio.alvares@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
google_chromeec_get_event returns an event number and 0 when there's no event.
This function is usually called in a loop until there are no more events, so
it makes sense to return 0 (i.e. no event) when there's an error.
BUG=b:184074997
TEST=Boot guybrush, no ec errors
Change-Id: I6c0186e4637af9ae24f45cce3638f0913227d6a7
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Defining the memory mapped base in fmap for example "FLASH@0xff800000
0x80000" for a 8M flash is optional in fmap files. This will also
reflect in the generated fmap_config.h. Fix the assembly cbfs walker
walkcbfs.S for fmap lacking a definition of the flash base.
Change-Id: I96b18f675e625abee503648ffdc6031978a4269a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
pmc_set_power_failure_state() is usually called twice, once upon boot
(with `target_on == true`) and once from SMM when the system is shut
down (with `target_on == false`). Assuming settings didn't change
between these calls, there is only one case where we actually need
to write the register value: when updating the state for the
MAINBOARD_POWER_STATE_PREVIOUS feature.
This suits us well as we want to avoid unnecessary writes so we
don't clobber the value set upon boot from within SMM. Due to
inaccessible option backends, SMM might not know the current
option state.
The assumption above, that the option value didn't change, may not
be true if the user changed the option on purpose. In the future,
one would have to reboot the machine for option changes to take
effect. However, this doesn't seem to make a huge difference: One
already needed a controlled shutdown for the update to take effect
before. A reboot doesn't seem much more expensive.
Change-Id: I58dd74b8b073f4f07db090bf7fddb14b5df8239a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55539
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch create separate helper functions to fill-in required
FSP-M UPDs as per IP initialization categories.
This would help to increase the code readability and in future
meaningful addition of FSP-M UPDs is possible rather adding UPDs randomly.
TEST=FSP-M UPD dump shows no change without and with this code change.
Change-Id: I5f23292fd1bd44d0cd55fbefd490b090ccd48365
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55225
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating the APOB takes a considerable amount of time. I decided to be
granular and split out the operations so we know when we read vs read +
erase + write.
BUG=b:179092979
TEST=Boot guybrush and dump timestamps
3:after RAM initialization 3,025,425 (44)
920:starting APOB read 3,025,430 (5)
921:starting APOB erase 3,025,478 (48)
922:starting APOB write 3,027,727 (2,249)
923:finished APOB 3,210,965 (183,238)
4:end of romstage 3,210,971 (6)
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I08e371873112e38f623f452af0eb946f5471c399
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
APIC Serial Bus pins were removed with ICH5 already, so a choice
'irq_on_fsb = 0' would not take effect. The related register BOOT_CONFIG
0x3 is also not documented since ICH5.
For emulation/qemu-q35 with ICH9 the choice INTERRUPT_ON_APIC_BUS was
wrong and ignored as BOOT_CONFIG register emulation was never implemented.
For ICH4 and earlier, the choice to use FSB can be made based on the
installed CPU model but this is now just hardwired to match P4 CPUs of
aopen/dxplplusu.
For sb/intel/i82371eb register BOOT_CONFIG 0x3 is also not defined
and the only possible operation mode there is APIC Serial Bus, which
requires no configuration.
Change-Id: Id433e0e67cb83b44a3041250481f307b2ed1ad18
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55257
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In acpi_soc_get_bert_region after the bert_errors_region call is was
checked if the region parameter is NULL after the call; since region is
a parameter of acpi_soc_get_bert_region, it's non-NULL. What we should
be checking here is if region points to a non-NULL pointer.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Coverity (CID:1457506)
Change-Id: I0523504d65725ab2d2df4db28a5dedd90697b917
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Split up PCH Kconfig into a separate file. While we're at it, also sort
selected options alphabetically.
Tested with BUILD_TIMELESS=1, coreboot.rom for the Purism Librem 13 v1
remains identical when not adding the .config file in it.
Change-Id: Ic3ff982e7108bf2d25a22e56ac2fbb93070df164
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
These macros were used to generate ACPI P-state entries, but Broadwell
now uses Haswell CPU code. These macros are unused and can be removed.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: Ib2baca2964d9177e7ab6630d4ced22c5d332fb6e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Keep deduplicating code. Have Broadwell PCH ASL borrow some equivalent
Lynx Point ASL files, and drop the now-unused files from Broadwell PCH.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: If5a8712a846bbf7c42db92167763935dee74c26f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Use hostbridge.asl from Haswell instead of Broadwell. Both files are
equivalent. Then, drop the now-unused hostbridge.asl from Broadwell.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I87d51727b75a9c59e2f5f3ba8d48c575ce93c78c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Include Haswell memmap.h from Broadwell iomap.h to deduplicate identical
definitions. This also prevents the definitions from falling out of sync
while the unification process is ongoing.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I850e5521effba3818f4e2a13b94281bf07857d50
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
GDXCBAR and EDRAMBAR are accounted for when reporting resources to the
allocator, but they are not present in the DSDT. In addition, coreboot
does not enable either range, but MRC.bin sets up GDXCBAR and does not
disable it afterwards. Not reporting GDXCBAR in the DSDT can result in
resource conflicts, and not enabling EDRAMBAR can cause issues on CPUs
with eDRAM.
Enable both GDXCBAR and EDRAMBAR in coreboot code, and report these
ranges in the DSDT. This matches what Broadwell does. The value for
the `GDXC_BASE_ADDRESS` macro matches what MRC.bin programs as well.
Tested on Asrock B85M Pro4 with an i7-4770S (no eDRAM):
- Still boots
- EDRAMBAR is now enabled with base address of 0xfed80000
- GDXCBAR is still mapped with base address of 0xfed84000
Change-Id: I5538873b30e3d02053e4ba125528d32453ef6572
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add defines for the sizes of northbridge MMIO windows and use them where
applicable. The macro names have been taken from Broadwell.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I845cba8acbd478cd325d2e364138336d985f9c34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Avoid using deprecated macros, where possible.
"GpioResetPwrGood" represents multiple valid updated values, depending
on the GPIO community and will be more difficult to update.
While Kabylake supports both sets of macros, it will cause build errors
on Coffeelake. In the GPD group, replace with "GpioDswReset."
Replace with "GpioResumeReset" in any GPP group.
Change-Id: Iab0bb09adad997bef3a2133c443471d4c634f423
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Move locking CPU MSRs during CPU init instead of using
CONFIG_PARALLEL_MP_AP_WORK functions.
The AES Lock enable bit caused CPU exception errors as this should not
run on HT siblings. The set_aesni_lock() function takes care of that.
Change-Id: I21598c3e9a153dce25a09b187ddf9cf6363039d3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55098
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disable all display related UPDs if IGD is not enabled as FSP
don't need to perform display port initialization while IGD itself
is disabled else assign UPDs based on devicetree config.
TEST=Dump FSP-M display related UPDs with IGD enable and disable
to ensure patch integrity.
Change-Id: I0479904141dfc5e707679109aa18b7ef4264cf96
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
1. Replace all pcidev_path_on_root() and is_dev_enabled() functions
combination with is_devfn_enabled().
2. Remove unused local variable of device structure type
(struct device *).
3. Replace pcidev_path_on_root() and dev->enabled check with
is_devfn_enabled() call.
TEST=Able to build and boot without any regression seen on ADL.
Change-Id: I92671992ec14fd2adca1635b0791ac8b456332e9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55292
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Replace all pcidev_path_on_root() and is_dev_enabled() functions
combination with is_devfn_enabled().
2. Remove unused local variable of device structure type (struct device *).
3. Replace pcidev_path_on_root() and dev->enabled check with is_devfn_enabled()
call.
TEST=Able to build and boot without any regression seen on EHL.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Iadf9145a11f27ff0e182f146b6fe5a01e6cf3ed8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
1. Replace all pcidev_path_on_root() and is_dev_enabled() functions
combination with is_devfn_enabled().
2. Remove unused local variable of device structure type (struct device *).
3. Replace pcidev_path_on_root() and dev->enabled check with is_devfn_enabled()
call.
TEST=Able to build and boot without any regression seen on TGLRVP.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Ic9d91b711bab83de1911e0b7ea876f2ad018c937
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55330
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Replace all pcidev_path_on_root() and is_dev_enabled() functions
combination with is_devfn_enabled().
2. Remove unused local variable of device structure type (struct device *).
3. Replace pcidev_path_on_root() and dev->enabled check with is_devfn_enabled()
call.
TEST=Able to build and boot without any regression seen on dedede
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I4919a1ec02df50bc41fd66d5f3a352108a7aa04c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
1. Replace all pcidev_path_on_root() and is_dev_enabled() functions
combination with is_devfn_enabled().
2. Remove unused local variable of device structure type (struct device *).
3. Replace pcidev_path_on_root() and dev->enabled check with is_devfn_enabled()
call.
TEST=Able to build and boot without any regression seen on CML.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Ib5df5fd32e2e2742d349754a942bf81ca505dd39
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
1. Replace all pcidev_path_on_root() and is_dev_enabled() functions
combination with is_devfn_enabled().
2. Remove unused local variable of device structure type
(struct device *).
3. Replace pcidev_path_on_root() and dev->enabled check with
is_devfn_enabled() call.
TEST=Able to build and boot without any regression seen on Reef.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I900038dd4b2e2d89b1236bbd26bec5f34483b9f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Trigger mode LAPIC_INT_LEVELTRIG was only used with LAPIC_DM_INIT,
specifically for (obsolete) Init Level De-assert.
Level LAPIC_INT_ASSERT is required to be set for all other delivery
modes other than LAPIC_DM_INIT.
This reverts the two above changes that X2APIC mode support introduced
to the IPI for LAPIC_DM_SMI.
Change-Id: I7264f39143cc6edb7a9687d0bd763cb2703a8265
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Depending on how the "middle-end" (yes, the gcc developers are
serious about that) optimizer ends up mangling the code, there may
or may not be a complaint about x being used uninitialized when it's
clearly not used at all.
So instead, why keep x in the first place? memcpy(foo, NULL, 0) is
the same as memcpy(foo, some_uninitialized_variable, 0) in that it
does nothing.
Change-Id: Ib0a97c3e3fd1a2a6aff37da63376373c88ac595d
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
CB:55356 removed static inline declarations from get_log_level(). This
commit puts them back. It also changes the method of accessing static
symbols in tests/console/routing-test to source file inclusion like
in CB:46458 to avoid changing tested source file.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Iaa5dcbccb327f819374967be51ef642b1fb25e7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55473
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for the ThinkPad W541 based on Peter Lemenkov's initial W541
port. Compiled and tested with SeaBIOS and Tianocore booting into Arch
Linux 5.10.32-lts. The Haswell mrc.bin blob is required.
Tested working:
- SATA SSD
- SATA DVD drive
- M.2 SATA
- All USB ports
- SD card reader
- Speakers/headphone jack
- Keyboard/touchpad
- libgfxinit
- VGA
- mini DisplayPort (Thunderbolt untested)
- eDP laptop screen
- NVIDIA GPU in Linux
- Camera/Mic
- Smartcard reader
- Internal flashing when IFD is unlocked
- ThinkPad basic dock (VGA, USB, Ethernet)
- CMOS options
- WLAN
- Bluetooth
- Ethernet
- Using me_cleaner
- All DDR3 slots
Not working:
- Keyboard backlight
- First boot can take up to 20s (MRC.bin is slow)
Untested:
- Thunderbolt
- Internal flashing when IFD is locked
- Other ThinkPad docks (DisplayPort, DVI, Audio)
- ExpressCard slot
- Battery thresholds
- WWAN card
- Fingerprint reader
- USB Debug console
Signed-off-by: Justin Wu <amersel@runbox.me>
Change-Id: Ia43070f51bba3cf59ba9b7d9e29e4e778efbeb08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52659
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Peter Lemenkov <lemenkov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In x86_64 code every function call consumes 32byte of stack with
no stack local variables being used. That limits the function call depth
in SMM to 32 or less.
Double the stack size to prevent overwriting the stack canary as seen
on HP8200 and x86_64 enabled.
Change-Id: Iee202ba2ae609a474d0eb3b06f49690f33f4eda8
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This fixes a hard to debug hang that could occur in any stage, but in
the end it follows simple rules and is easy to fix.
In long mode the 32bit displacement addressing used on 'mov' and 'lea'
instructions is sign-extended. Those instructions can be found using
readelf on the stage and searching for relocation type R_X86_64_32S.
The sign extension is no issue when either running in protected mode or
the code module and thus the address is below 2GiB. If the address is
greater than 2GiB, as usually the case for code in TSEG, the higher
address bits [64:32] are all set to 1 and the effective address is
pointing to memory not paged. Accessing this memory will cause a page
fault, which isn't handled either.
To prevent such problems
- disable R_AMD64_32S relocations in rmodtool
- add comment explaining why it's not allowed
- use the pseudo op movabs, which doesn't use 32bit displacement addressing
- Print a useful error message if such a reloc is present in the code
Fixes a crash in TSEG and when in long mode seen on Intel Sandybridge.
Change-Id: Ia5f5a9cde7c325f67b12e3a8e9a76283cc3870a3
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
After ChromeOS NVS was moved to a separate allocation and the use
of multiple OperationRegions, maintaining the fixed offsets is not
necessary.
Use actual structure size for OperationRegions, but align the
allocations to 8 bytes or sizeof(uint64_t).
Change-Id: I9c73b7c44d234af42c571b23187b924ca2c3894a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The system will hang when resuming from S3 if the SSD reset gpio is not
reset early enough.
Change GPP_A11 in baseboard to PLTRST to avoid an S3 resume hang.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: Ia78d813cb6bc689b07e8d8ead1ade6e77f925ce1
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Part of the soc/amd/stoneyridge code already uses the FCH_IOAPIC_ID and
GNB_IOAPIC_ID defines. Use those defines in the remaining location to
make sure that the IOAPIC IDs are always consistent between the hardware
register, the MADT and the IVRS ACPI tables.
TEST=Timeless build of amd/gardenia results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I410a6560de66889b153c8a66b8dc5474ac114ba7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Now that device NVS is no longer used as such, stop using it to store
ACPI device settings consumed by the SSDT generator. Instead, provide
the get_acpi_device_state() function to allow saving ACPI device BARs
and activation state from other compilation units. Also, introduce an
enum and a struct to ease handling device state.
Tested on out-of-tree Compal LA-A992P, SerialIO SSDT does not change.
Change-Id: I9e70bf71e808651cb504399dcee489a4d1a70e67
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52521
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The same functionality can be provided through a runtime-generated SSDT.
The remaining parts of device NVS are removed in a follow-up.
Since the SSDTs are only loaded after the DSDT (if loaded at all), using
SSDT-provided objects outside method bodies is not possible: the objects
are not yet in OSPM's ACPI namespace, which causes in ACPI errors. Owing
to this, the operation regions used by the _PS0 and _PS3 methods need to
be moved into the SSDT, as they depend on the SSDT-provided BAR1 values.
Tested on out-of-tree Compal LA-A992P, generated SSDT disassembles with
no errors and contains expected values. Linux does not complain either.
Change-Id: I89fb658fbb10a8769ebea2e6535c45cd7c212d06
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Use the same code from Lynx Point on Broadwell, and adjust as needed.
Also add a config file to ensure the code gets build-tested.
Tested on out-of-tree Compal LA-A992P (Haswell ULT), UART 0 works.
Change-Id: I527024098738700d5fbaf3e27cf4db331a0322bd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
In ACPI mode the device cannot be enumerated and thus the payload and
bootloader doesn't know about the active resources.
An ACPI aware OS can use the _CRS to determine the active MMIO window.
Mark the BAR0 as reserved if the device is in ACPI mode to make sure the
BAR is reserved in e820 tables.
Change-Id: I6079b1eb7b0c87c752515340aac8776244b30ca0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Create the gimble variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:190334274
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_GIMBLE
Change-Id: If425571d95b3b20910f890428fb5726ebad2fdf4
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55300
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `location` member of `struct boot_state_callback` is conditionally
guarded depending on `CONFIG(DEBUG_BOOT_STATE)` using preprocessor. It
is probably intended to save some space when the `location` strings do
not get printed. However, directly using the `location` member without
any guards will cause a compile-time error. Plus, preprocessor-guarded
code gets nasty really quickly.
In order to minimise preprocessor usage, introduce the `bscb_location`
inline helper function, which transforms the compile-time error into a
link-time error. It is then possible to substitute preprocessor guards
with an ordinary C `if` statement.
Change-Id: I40b7f29f96ea96a5977b55760f0fcebf3a0df733
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Create the scout variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:187080143
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_SCOUT
Signed-off-by: Jeff Chase <jnchase@google.com>
Change-Id: I3be9d2d30821c2c9132ed94c9faf1f33b62bbc7e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
We are not currently tracking how long it takes to load verstage. The
enum values already exist, they just weren't used.
BUG=b:179092979
TEST=Dump timestamps
501:starting to load verstage 2,280,656 (1)
502:finished loading verstage 2,340,845 (60,189)
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I2cde58cb8aa796829a4e054e6925e2394973484b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The warm reset bit in the NCP_ERR register doesn't behave as the PPR [1]
suggested; no matter if something was written to the register, the
NCP_WARM_BOOT bit never got set and the NCP_ERR register in I/O-space
always reads back as 0x7f.
[1] checked with PPR for AMD Family 19h Model 51h A1 (CZN) #56569 Rev
3.01
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I569372db9f36ec7bbc741f4d7312ade312daa70b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55101
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Order of bits in bitfields is implementation-defined. This makes them
non-portable, especially across systems using different endianness.
This change removes bitfields and uses masking and shifting instead.
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Change-Id: Ief7d87ddb25c9baa931f27dbd54a4ca730b6ece7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Restructuring opregion VBT related code to make it more generalize
for future revision of opregion spec.
Moved logic to locate VBT from different region (CBMEM, PCI option
ROM or VBIOS) into separate function.
Created a new function to check if extended VBT region is required.
This will be helpful in the subsequent changes to determine if
extended VBT region is needed and handle memory allocation
accordingly.
BUG=None
BRANCH=None
TEST=check the address of extended VBT region and address is coming
correctly.
Change-Id: I479d57cd326567192a3cd1969f8125ffe1934399
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
On Linux, in order to set wake alarms >24 hours, the RTC Date Alarm
field must be set to a valid non-zero value. If not, there are two
consequences:
1. Alarms >24 hours don't work
2. The kernel will refuse to enter suspend because it can't resume as
expected to service the alarm.
Since the RTC Date Alarm and RTC AltCentury fields are supported on
Stoneyridge, set them.
This is a mirror of commit 041fcf5902
("soc/amd/picasso/acpi: Set missing RTC offsets") for picasso.
BUG=b:187516317
TEST=On a Chrome OS 'grunt' device, run
`time powerd_dbus_suspend --suspend_for_sec=172800`
and verify the system suspended and woke up after 48 hours
BRANCH=grunt
Signed-off-by: Anand K Mistry <amistry@google.com>
Change-Id: I10831b982662e680fa71aa81d02935e1b7e7a7a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add EC_HOST_EVENT_HANG_DETECT to S3/S5/S0ix wake mask. This event is
sent when the EC detects the AP didn't fully enter a sleep state.
BUG=b:186571086
TEST=Trigger hang detect while AP is in S0ix, AP wakes from S0ix
Change-Id: I09ccf609fc453c19b4fb1ddaa5a0c86d7a85aad1
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add GPIO pin details specific to SC7280 chipset
for the consumers to be able to request for the
gpio functionality as per their requirement.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Change-Id: I63bcaed78a6eeb0e6fad857b89d40181613e50cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
The patch updates PMC Descriptor which is part of Descriptor Region if
system equipped with Alder lake A0 silicon. This change allows to use
unified Descriptor Region for Alder lake A0(CPU ID:0x906a0) and B0
(CPUD ID:0x906a1) silicons.
BUG=B:187431859
TEST=Verified PMC Descriptor getting modified for Alder lake B0 silicon if
not updated.
coreboot logs appear as below with this patch:
On First boot after flashing the image:
coreboot-coreboot-unknown.9999.4589c0f Wed Jun 9 18:23:43 UTC 2021 bootblock starting (log level: 8)...
CPU: Genuine Intel(R) 0000
CPU: ID 906a0, Alderlake Platform, ucode: 0000001a
..
FMAP: Found "FLASH" version 1.1 at 0x1804000.
FMAP: base = 0x0 size = 0x2000000 #areas = 32
FMAP: area SI_DESC found @ 0 (4096 bytes)
SF: Detected 00 0000 with sector size 0x1000, total 0x2000000
Erasing flash addr 0 + 4 KiB
Update of PMC Descriptor successful, trigger GLOBAL RESET
Next boot after GLOBAL RESET:
coreboot-coreboot-unknown.9999.4589c0f Wed Jun 9 18:23:43 UTC 2021 bootblock starting (log level: 8)...
..
FMAP: area SI_DESC found @ 0 (4096 bytes)
SF: Detected 00 0000 with sector size 0x1000, total 0x2000000
Update of PMC Descriptor is not required!
VBOOT: Loading verstage.
..
CBFS: Found 'fallback/verstage' @0x2264c0 size 0x16b08 in mcache @0xfef84d38
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I6d9a2ce0f0b3e386eefa1962ce706b58f31a8576
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Since common CPU ID between ADL-P and ADL-M CPU IDs, the patch renames all
ADL-P and ADL-M Silicon CPUID macros and defines generic name
"Alderlake Platform" as macro value. Also, this will avoid log ADL-M for
ADL-P CPU and vice-versa. Although currently name field of "cpu_table"
points to only "Alderlake Platform, but it is retained asa placeholder in
future difference platforms.
Please refer EDS doc# 619501 for more details.
The macros are renamed as below:
CPUID_ALDERLAKE_P_A0 -> CPUID_ALDERLAKE_A0
CPUID_ALDERLAKE_M_A0 -> CPUID_ALDERLAKE_A1
CPUID_ALDERLAKE_P_B0 -> CPUID_ALDERLAKE_A2
TEST=Verify boot on Brya. After change, relevent coreboot logs appear as
below:
CPU: ID 906a1, Alderlake Platform, ucode: 00000119
CPU: AES supported, TXT supported, VT supported
MCH: device id 4601 (rev 03) is Alderlake-P
PCH: device id 5181 (rev 00) is Alderlake-P SKU
IGD: device id 46b0 (rev 04) is Alderlake P GT2
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ia06d2b62d4194edd4e104d49b340ac23305a4c15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55252
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit adds support for the Chrome OS Zero-Touch Enrollment related
spaces. For TPM 2.0 devices which don't use Cr50, coreboot will define
the RMA+SN Bits, Board ID, and RMA Bytes counter spaces.
The RMA+SN Bits space is 16 bytes initialized to all 0xFFs.
The Board ID space is 12 bytes initialized to all 0xFFs.
The RMA Bytes counter space is 8 bytes intialized to 0.
BUG=b:184676425
BRANCH=None
TEST=Build and flash lalala, verify that the ZTE spaces are created
successfully by undefining the firmware antirollback space in the TPM
such that the TPM undergoes factory initialization in coreboot. Reboot
the DUT. Boot to CrOS and run `tpm_manager_client list_spaces` and
verify that the ZTE spaces are listed. Run `tpm_manager_client
read_space` with the various indices and verify that the sizes and
initial values of the spaces are correct.
TEST=Attempt to undefine the ZTE spaces and verify that it fails due to
the unsatisfiable policy.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I97e3ae7e18fc9ee9a02afadbbafeb226b41af0eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55242
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit adds support for the TPM2_NV_SetBits command to the TLCL.
This command is used to set bits in an NV index that was created as a
bit field. Any number of bits from 0 to 64 may be set. The contents of
bits are ORed with the current contents of the NV index.
The following is an excerpt from lalala undergoing TPM factory
initialization which exercises this function in a child commit:
```
antirollback_read_space_firmware():566: TPM: Not initialized yet.
factory_initialize_tpm():530: TPM: factory initialization
tlcl_self_test_full: response is 0
tlcl_force_clear: response is 0
tlcl_define_space: response is 14c
define_space():197: define_space: kernel space already exists
tlcl_write: response is 0
tlcl_define_space: response is 14c
define_space():197: define_space: RO MRC Hash space already exists
tlcl_write: response is 0
tlcl_define_space: response is 14c
define_space():197: define_space: FWMP space already exists
tlcl_write: response is 0
tlcl_define_space: response is 0
tlcl_write: response is 0
tlcl_define_space: response is 0
tlcl_write: response is 0
tlcl_define_space: response is 0
tlcl_set_bits: response is 0
tlcl_define_space: response is 0
tlcl_write: response is 0
factory_initialize_tpm():553: TPM: factory initialization successful
```
BUG=b:184676425
BRANCH=None
TEST=With other changes, create a NVMEM space in a TPM 2.0 TPM with the
bits attribute. Issue the command and verify that the TPM command
succeeds.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I6ca6376bb9f7ed8fd1167c2c80f1e8d3c3f46653
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55241
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently variant_has_fpmcu() is called very early in bootblock, before
eSPI is initialized. When checking CBI for its presence, that causes
an error and nothing else can be read from CBI in bootblock.
Moving it slightly later in bootblock doesn't hurt anything from a
timing standpoint, and allows CBI to be read.
BUG=None
TEST=See CBI get read and the FPMCU field read correctly.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I6de44119e92c8820b266f9f07287706c7d4eb505
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch assings 2 to EC_EFS_BOOT_MODE_TRUSTED_RO to make coreboot
set VB2_CONTEXT_EC_TRUSTED when the GSC reports TRUSTED_RO.
Old GSC doesn't use 2. So, the new BIOS won't mistakenly set
VB2_CONTEXT_EC_TRUSTED.
BUG=b:180927027, b:187871195
BRANCH=none
TEST=build
Change-Id: I11a09d0035a4bd59f80018c647ca17e3318be81e
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55373
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The loads of the FSPM and FSPS binaries are not insignificant amounts of
time, and without these timestamps, it's not clear what's going on in
those time blocks. For FSPM, the timestamps can run together to make it
look like that time is still part of the romstage init time.
Example:
6:end of verified boot 387,390 (5,402)
13:starting to load romstage 401,931 (14,541)
14:finished loading romstage 420,560 (18,629)
970:loading FSP-M 450,698 (30,138)
15:starting LZMA decompress (ignore for x86) 464,173 (13,475)
16:finished LZMA decompress (ignore for x86) 517,860 (53,687)
...
9:finished loading ramstage 737,191 (18,377)
10:start of ramstage 757,584 (20,393)
30:device enumeration 790,382 (32,798)
971:loading FSP-S 840,186 (49,804)
15:starting LZMA decompress (ignore for x86) 853,834 (13,648)
16:finished LZMA decompress (ignore for x86) 888,830 (34,996)
BUG=b:188981986
TEST=Build & Boot guybrush, look at timestamps.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I5796d4cdd512799c2eafee45a8ef561de5258b91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Using the linker's --wrap feature has the downside that it only covers
references across object files: If foo.c defines a() and b(), with b
calling a, --wrap=a does nothing to that call.
Instead, use objcopy to mark a weak and global so it can be overridden
by another implementation, but only for files originating in src/.
That way mocks - implemented in tests/ - become the source of truth.
TEST=Had such an issue with get_log_level() in a follow-up commit, and
the mock now takes over. Also, all existing unit tests still pass.
Change-Id: I99c6d6e44ecfc73366bf464d9c51c7da3f8db388
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
ptrdiff_t, wchar_t, and wint_t are all integer types built-in to the C
language (as opposed to being library-only types defined in a header).
In the past we had to define these typedefs ourselves because of romcc,
but now that it's gone we should use the GCC-provided macros to select
the types the compiler expects.
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I0874eddf780b6e41ce773ad8b4faa595e4bbd8a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Select `HAVE_INTEL_FSP_REPO` so that the FSP binary from the FSP
repository is used by default. Also, use the FSP headers from the FSP
repository and adjust some UPD names so that coreboot is able to use
them.
Also added new config FSP_TYPE_CLIENT/IOT. Respective mainboard Kconfigs
to select right FSP_TYPE when using FSP repository.
BUG=b:175957775
BRANCH=none
Change-Id: I5e694b91be7734dd98665051a6a3d9eccab7dac7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
The 3rdparty submodule 'intel-microcode' has changed the branch from
'master' to 'main'. As we do not set any specific branch name in our
config, it defaults to 'master' which makes
"git submodule update --remote --rebase 3rdparty/intel-microcode"
to fail.
This patch adds the branch name in .gitmodules to match the upstream
name.
Change-Id: I7b6d7921a21af4eb3bcc7ce4e5a8ea21c38c89a3
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55304
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: siemens-bot
Add lpddr4.c utility file with lpddr4_speed_mhz_to_reported_mts.
Fill in lpddr4_speeds using JDEC 209-4C table 210.
LPDDR4 SPD decoding utilities are not included since there isn't
a present need.
BUG=b:184124605
TEST=Build and run on guybrush
Change-Id: Id8ddfc98fff4255670c50e1ddd4d0a1326265772
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Derived from Broadwell and adapted to follow what soc/intel does. Note
that SERIALIO_UART_CONSOLE is meant to be selected from the mainboards
which expose a SerialIO UART. UART_FOR_CONSOLE also needs to be set in
mainboard Kconfig accordingly.
It is possible that some of the UART configuration steps in bootblock
are unnecessary. However, some of the steps turn off power management
features and others are undocumented: omitting them could cause weird
issues.
Finally, add a config file to ensure the code gets build-tested.
Tested on out-of-tree Compal LA-A992P, SerialIO UART 0 can be used to
receive coreboot and SeaBIOS logs.
Change-Id: Ifb3460dd50ed03421a38f03c80f91ae9fd604022
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52489
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allows compile-time optimisation on platforms that do not wish
to enable runtime checking of X2APIC.
Legacy lapic_cpu_init() is incompatible so there is dependency
on PARALLEL_MP. Also stop_this_cpu() is incompatible, so there
is dependency on !AP_IN_SIPI_WAIT.
Since the code actually lacks enablement of X2APIC (apparently
assuming the blob has done it) and the other small flaws pointed
out in earlier reviews, X2APIC_RUNTIME is not selected per
default on any platform yet.
Change-Id: I8269f9639ee3e89a2c2b4178d266ba2dac46db3f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
All functions in ec_skuid.c except google_chromeec_get_board_sku()
are for SMBIOS platforms. Move these functions to a new file to allow
non-SMBIOS platforms to use google_chromeec_get_board_sku() without
having to declare MAINBOARD_SMBIOS_MANUFACTURER.
BUG=none
TEST=emerge-cherry coreboot
BRANCH=none
Change-Id: I8916223f5f04afe4761be4ad3313e900efae90d4
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add function to force memory training and add VPD variable to operate
this function.
Tested=On OCP Delta Lake, memory training can be forced via VPD.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I53a923b51b36f9f5db491ef142109f58f9a4611d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Correct GPIO settings as below reason:
1. GPP_D19/GPP_D20/GPP_D21 not being used but set to NF.
2. GPP_B7 should configure as WWAN SAR detect ODL, but set to GPI
BUG=b:188956448
BRANCH=dedede
TEST=The LTE DPR pin can be pulled down normally when someone
get close to the P-sensor antenna.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Idc214fcd9c4631368a71f4d59bb644df739982ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This patch adds a new test to checkpatch that identifies cases where a
line after a conditional statement is incorrectly intended (possibly
indicating the mistake of forgetting to add braces), like this:
if (a)
b;
c;
Unfortunately, it seems like checkpatch is partially unmaintained in
upstream Linux at the moment with maintainers either not responding at
all or not even willing to look at new patches [1]. Since detecting this
error class is important to coreboot, let's just carry this feature
locally for now.
[1] https://lkml.org/lkml/2021/4/15/1488
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I7bb90b56dfc7582271d2b82cb42a2c1df477054f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
acpi_soc_get_bert_region only gets called when a chipset's Kconfig
selects the ACPI_BERT option in which case the chipset code needs to
implement this function. In the case of acpi_soc_get_bert_region not
being implemented, but ACPI_BERT being selected for a chipset this patch
changes the behavior from never generating a BERT ACPI table to a build
error which is more obvious and easier to catch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id479fce823d8534a7790f39125d1a2b3635fc029
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55277
Reviewed-by: Lance Zhao
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This also adds BERT table gerenation support for Cezanne, but since the
functionality to populate the BERT memory region isn't implemented yet,
this won't result in a BERT table being generated on Cezanne, since
bert_generate_ssdt will always return false there.
TEST=BERT ACPI table generation still works on AMD/Mandolin
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I69b4a9a7432041e1f4902436fa4e6dee5332dbd2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The CrashLog raw_data_length, previously used to track the length for
the Intel CrashLog decoder, is causing noises in the Linux kernel
for AMD. Hence this update made at the soc level which will enable the
pulling put of the tracking from x86/acpi_bert_storage.c.
BUG=None
TEST=Built, and BERT successfully generated in the crashLog flow.
Signed-off-by: Francois Toguo Fotso <francois.toguo.fotso@intel.com>
Change-Id: I97ff14d62bda69389c7647fcbbf23d5cab2b36e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55006
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since bert_errors_present() is only available when ACPI_BERT is selected
the ACPI table generation code needs to check that before calling the
function, so add bert_should_generate_acpi_table that returns false when
ACPI_BERT isn't selected or the return value of bert_errors_present()
when ACPI_BERT is selected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia955f627c190ea38e05b5aaedc7cb2d030274e83
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55024
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Check if the ACPI_BERT Kconfig option is selected and only then try to
generate the BERT table. Also remove the acpi_is_boot_error_src_present
weak function from the ACPI global compilation unit and use the return
value of acpi_soc_get_bert_region to determine if there is a valid BERT
region with logged errors.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2a281f5f636010ba3b2e7e097e9cf53683022aea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This will tell the kernel to ignore PCI ASPM when suspending the device
and instead place the device into D3. We don't actually have a pin to
control power to the NVMe so we leave it in D3Hot. I'm not sure if
`PCI_RST#` is working correctly on S0i3 suspend/resume. If it's not
acting as expected we can add the reset GPIO and have the OS do it.
BUG=b:184617186
TEST=Run suspend_stress_test on guybrush for 10 cycles
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I29539ac120a9f1b7c1bfeaca745cfc82acfa461a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54967
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Power limits (PL1 and PL2) depend on the specific SKU of the CPU.
By expanding the SoC chip config power_limits_config member to
an array indexed by ADL_*_POWER_LIMITS_*_CORE macros, the
appropriate power limits are applied. Using this the correct
set of power limits are being selected from the array based on
system agent PCI ID. Based on this, chipset.cb file contains
the set of power limits being used by varieties of ADL boards.
These power limit values are as per document 619501.
BUG=None
BRANCH=None
TEST=Built and verified the following console output on below boards
On adlrvp (482):
CPU PL1 = 28 Watts
CPU PL2 = 64 Watts
On adlrvp (682):
CPU PL1 = 45 Watts
CPU PL2 = 115 Watts
On brya (282):
CPU PL1 = 15 Watts
CPU PL2 = 55 Watts
Change-Id: Ic1676e2b4d611cdc85e770f131d5b6d5ecd180be
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
The return value indicates if the function has found valid BERT data and
wrote them to the region and length parameters. This will be used in a
follow-up patch to remove the acpi_is_boot_error_src_present function
call in the common code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaaa3eed51645e1b3bc904c6279d171e3a10d59be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55053
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ACPI device ID of IOM device has been changed for Alder Lake.
Updating it to make it compatible with kernel
TEST=ACPI ID is updated and kernel driver works as expected
Cq-Depend: chromium:2936144
Change-Id: Ifdfcd0c1534e8204719e59e718688cd42e846e84
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
EDK2 mandates HOB to be in increments of qword (8). This HOB has 13
elements which causes it be padded with 4 bytes of garbage. This
results in coreboot failing intermittently with invalid data. Add
"number of entries" field to specify the number of valid entries in
the table.
BUG=b:190153208
Cq-depend: chrome-internal:3889619
TEST=verify HOB is present and correct size (13) is reported
Change-Id: Iaafae304f04a5f26d75a41a6d6fcb4ee69954d20
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55237
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This driver was inspired from soc/intel/common/block/pci/rtd3. I decided
to copy and modify it because the Intel driver has a lot of Intel
specific code.
This driver has been stripped down to only provide a power resource and
set the StorageD3Enable property. This driver is SoC agnostic and does
not handle suspending the actual PCIe root port. That should be
implemented by an SoC specific driver.
This is required for Guybrush to suspend/resume properly because the
NVMe power is tied to the S0 power rails, so the kernel needs to place
the device into D3.
BUG=b:184617186
TEST=Guybrush is able to suspend/resume properly. Also see power
resource get enabled / disabled.
[ 56.075559] power-0416 __acpi_power_off : Power resource [RTD3] turned off
[ 56.075562] device_pm-0279 device_set_power : Device [PXSX] transitioned to D3cold
[ 56.075567] pci_pm_suspend_noirq: nvme 0000:02:00.0: PCI PM: Suspend power state: D3cold
[ 56.075569] nvme 0000:02:00.0: pci_pm_suspend_noirq+0x0/0x413 returned 0 after 15978 usecs
[ 123.464874] nvme 0000:02:00.0: calling pci_pm_resume_noirq+0x0/0x11d @ 7, parent: 0000:00:02.4
[ 123.464891] acpi_device_set_power: ACPI: \_SB_.PCI0.GP14.PXSX: Power state change: D3cold -> D0
[ 123.464982] power-0360 __acpi_power_on : Power resource [RTD3] turned on
[ 123.464984] device_pm-0279 device_set_power : Device [PXSX] transitioned to D0
[ 123.465039] nvme 0000:02:00.0: pci_pm_resume_noirq+0x0/0x11d returned 0 after 158 usecs
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I2adfc925183ff7a19ab97e89212bc87c40d552d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change drops the following unused lpss functions and related
code:
* soc_lpss_controllers_list
* is_dev_lpss
These functions were added to determine if a controller is LPSS for
performing IRQ configuration. But, these never got used and hence are
being dropped.
Change-Id: I27bdfbca7c199e823a0e4fdb277e3f22fb6bae7a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
commit d3b49b4
[payloads/Tianocore: Update default build target, simplify build options]
simplified the build string and removed the bootloader Makefile variable,
but one reference was missed. Luckily the variable being empty didn't
break things, but correct it regardless.
Change-Id: If37b291dda59c20bfe4c6e5b9100fac52d11a2f4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55239
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
acpi_device_add_power_res currently generates a `_STA` method hardcoded
to ON. This change enables the ability to generate a `_STA` method that
queries the status of the GPIOs to determine if the power resource is ON
or OFF.
BUG=b:184617186
TEST=Dump SSDT table for guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I91410556db002c620fd9aaa99981457808da93a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Some of the I2C buses are required to operate at different voltage level
compared to other I2C buses eg. I2C bus to Google Security Chip (GSC)
should be at 1.8V level. By default, all the I2C buses are initialized
to operate at 3.3 V. Add support to configure I2C pad RX select through
devicetree and update the concerned devicetree.
BUG=b:188538373
TEST=Build and boot to OS in Guybrush. Ensure that the communication
with GSC is fine. Build Majolica mainboard.
Change-Id: I595a64736fdac0274abffb68c5e521302275b845
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some of the GPIOs are either re-purposed for different use-cases or are
unused in upcoming board phase (board version 2). Update the GPIO
configuration accordingly. Here are the GPIOs that are updated:
GPIO Board Id 1 Board Id 2
=============================================
GPIO31 TP183 EN_SPKR
GPIO69 EN_SPKR SD_AUX_REST_L
GPIO70 SD_AUX_RESET_L Unused TP27
GPIO74 RAM_ID_CHAN_SEL Unused TP49
BUG=b:189327557, b:188542649, b:188542497
TEST=Build Guybrush mainboard. Verify Audio is audible and SD card is
detected fine in Board ID 1.
Change-Id: I31523b3e03d2b59577f33eae548747834cfc98aa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Logging to coreboot cbmem, instead of a serial console, was
added to MrChromebox's uefipayloadpkg branch. Add a Kconfig
option to enable this, and restrict it to the UEFIPAYLOAD
payload option, since this feature does not exist in upstream
edk2.
Change-Id: Idef125235dc7ba885eb22ac69c6f752588a9e295
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
IO MWAIT redirection is disabled, which means reads to the P_LVL2 and
P_LVL3 "registers" will never produce any C-state transition requests.
Moreover, the register resource descriptors for all reported C-states
use the FFixedHW address space, not I/O.
Change-Id: I026835dd24d7ac1e1bae2d851e011e1670abaad4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Even if IO MWAIT redirection were enabled, the base address is wrong.
Moreover, the register resource descriptors for all reported C-states
use the FFixedHW address space, not I/O.
Change-Id: Ic2faaafbe4928994aeeab8098d8e0fb6703d203d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
bin/{foo,bar,baz} can fail if one of the files doesn't exist (depending
on the shell in use). Instead, cd into the directory and list the
files individually.
Change-Id: I042b2e45fded1b63551d8e65ead2a7bbbf96b1e7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Use the device aliases provided by alderlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
shadowmountain board variants.
TEST=Dump devicetree device enable list without and with this CL, no
difference observed.
Change-Id: I2b769d653ad8ad8ff069a0787d00ff33ead5c912
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Use the device aliases provided by alderlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
different adlrvp boards.
TEST=Dump devicetree device enable list without and with this CL, no
difference observed.
Change-Id: Ib9e82d953416c076588974f3167d00ae96f01bb5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55205
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch makes coreboot set VB2_CONTEXT_EC_TRUSTED based on the EC"s
boot mode. Vboot will check VB2_CONTEXT_EC_TRUSTED to determine
whether it can enter recovery mode or not.
BUG=b:180927027, b:187871195
BRANCH=none
TEST=build
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I9fa09dd7ae5baa1efb4e1ed4f0fe9a6803167c93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add common gpio functionalities across qualcomm soc targets.
This common gpio driver would allow the consumers to be able to
configure gpio function, set/get gpio direction as input/output,
configure the gpio as pull-up/pull-down, configure the gpio as an
IRQ and also query the gpio irq status.
The GPIO pin definition would be SoC specific.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Change-Id: Ia672130c6ca938d9284cae5071307637709480d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55076
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The I2C bus at which the external RTC is attached to is operated at
standard speed (100 kHz) at coreboot runtime. The OS can choose to run it
at fast speed since it uses its own driver and controller setup.
Report additional bus timings for fast mode so that OS can do it right.
Change-Id: I82e11e5dde8ad1047713f105c5a6d020eebf1ffd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55089
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the OS provides its own driver for the I2C controller it can
choose to use a bus speed other than the one used at coreboot runtime.
In this case it would be good to provide a way how the needed bus
timings are communicated to the OS, since these are very board-specific
and there is no way that the OS can know them other than read the
appropriate ACPI reported timings.
This patch adds some code to report additional bus speed timings if
there are some defined in the devicetree.
Change-Id: If921e0613864660dc1bb8d7c1b30fb9db8ac655d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This patch adds the ACPI hardware error source table (HEST) support.
This involves a few different parts: (1) The ACPI HEST table which is filled
with the appropriate fields (2) Reserved memory which is used by runtime
SW to provide error information. OS will not accept a HEST table with
this memory set to 0.
The ASL code to enable APEI bit will be submitted in a separate patch.
Tested on DeltaLake mainboard with following options enabled
SOC_INTEL_XEON_RAS
After boot to Linux, the following will show in dmesg:
HEST: Table parsing has been initialized
Change-Id: If76b2af153616182cc053ca878f30fe056e9c8bd
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
For all of the audio devices in overridetree.cb add the probe matches
that will determine if the device should be enabled or not based on the
selected audio daughter board type.
AUDIO=MAX98357_ALC5682I_I2S: enable max98357, dmic1 and alc5682i
AUDIO=MAX98373_ALC5682_SNDW: enable max98373, dmic2 and alc5682
BUG=b:188696010
TEST=test different audio devices based on fw_config value:
> AUDIO=UNKNOWN
ectool cbi set 6 0x00000000 4 2
> AUDIO=MAX98357_ALC5682I_I2S
ectool cbi set 6 0x00000100 4 2
> AUDIO=MAX98373_ALC5682_SNDW
ectool cbi set 6 0x00000200 4 2
Change-Id: I6f159442516830f9d304d78c83f070e4fcff4a37
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (<400 kHz).
Measured I2C frequency changes are just as below after tuning:
touchpad: 434kHz ---> 391kHz
touchpanel: 439kHz ---> 382kHz
audio codec RT5682: 445kHz ---> 385kHz
BUG=b:187555396
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400 kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I8438e37be49f8a74f53fd8460110dac1a3f06993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The entries in the ACPI tables for the fingerprint module's SPI
configuration were incorrect.
1) The GPIO is routed to IOAPIC (and SCI), therefore in ACPI, it must be
described by Interrupt(), not GpioInt()
2) The chip-select signal was selected as 1, not 0 `device spi 0/1 on`
BUG=b:181635081
TEST=verified in kernel logs:
localhost # ~ dmesg|egrep 'cros-ec-dev|cros-ec-spi'
[ 4.569412] cros-ec-dev cros-ec-dev.1.auto: CrOS Fingerprint MCU detected
[ 4.575303] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I9ef6c99f011969fc444e0c12b806529cb82bba3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55147
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 255b6f8646.
No longer needed after commit dd01e0131a
(Revert "util/lint: Add test for documentation in util dirs") has been
submitted. Plus, `util/vboot_lib/description.md` gets deleted whenever
one runs `make -C util/cbfstool clean`, which is rather annoying.
Change-Id: Ic93da096b6186d1d2af12243a74ec597694960c4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55162
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are two touch pads that Sasukette used have the same I2C address.
It will show "/dev/input/event4: SPPT2600:00 06CB:CE9D Touchpad" when
the Synaptics touch pad is connected after running evtest under VT2.
BUG=b:189520603
BRANCH=dedede
TEST=It will show "/dev/input/event4: SYNA0A00:00 06CB:CE9D Touchpad"
when the Synaptics touch pad is connected after running evtest under VT2.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: If0bd80baa27dfeb7bcb43f0ca4b02e1228e372a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55035
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the primus variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0)
BUG=b:188272162
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_PRIMUS
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I26787f296793b281b7f1ee1a7d240006163c6015
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
CB:52586 ("util/spd_tools: Add MT53E1G32D2NP-046 WT:B LPDDR4 config")
incorrectly set ranks per channel to 1. However, MT53E1G32D2NP-046 WT:B
part has 2 channels per die and 2 physical dies. Each channel in each die shares DQ-DQS lines with the channel in other die and uses separate CS lines. Thus, number of ranks per channel is 2.
This change fixes the attribute ranksPerChannel for MT53E1G32D2NP-046 WT:B in LP4x global config by setting it to 2.
BUG=b:186616388
Change-Id: Iba87754ca04c2e026a9cbc8ef07412b467140cba
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Since the MCA(X) registers have defined values on the cold boot path,
the is_warm_reset check can be dropped. Also the warm reset bit in the
NCP_ERR register doesn't behave as the PPR [1] suggested; no matter if
something was written to the register or the machine went through a warm
reset cycle, the NCP_WARM_BOOT bit never got set.
[1] checked with PPR for AMD Family 17h Models 11h,18h B1 (RV,PCO)
#55570 Rev 3.15
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4e6df98ffd5d15ca204c9847a76c19c753726737
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The chipset devicetree only has the essential PCIe devices enabled that
are needed for the SoC code to work. It also defines aliases for all
PCIe devices that can be used to reference the devices in the mainboard-
specific devicetrees and devicetree overrides. To make the change easier
to review that part will be done in a follow-up patch.
Despite missing in the PPR, device pci 18.7 exists on Picasso.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b7c3fd32579a23539594672593a243172c161c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
OCP Delta Lake is developed and validated against LinuxBoot payload.
Need to put the respective binary blobs in site-local/deltalake to
build the final coreboot image.
Add LINUX_COMMAND_LINE for LinuxBoot payload kernel cmdline,
CPU_UCODE_BINARIES for CPU microcode binary, CONSOLE_SERIAL_57600 is
the serial baud rate used by OCP Delta Lake, DEFAULT_CONSOLE_LOGLEVEL_4
is for a faster boot time.
Tested=On OCP Delta Lake it can boot up target CentOS 8 GNU/Linux OS.
Change-Id: Ib494e4170a7ebb445d9e11df83c370b40a9e5194
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55058
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PLTRST# is currently asserted and latched when eSPI_RST# gets asserted.
If eSPI_RST# isn't used on a platform or it doesn't properly assert
in all cases, then PLTRST# will never be asserted. This could result in
the AP and EC being out of sync.
BUG=b:188188172, b:188935533
TEST=Warm reset guybrush with partial #22 rework. Verify that peripheral
channel is correctly reset.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I20d12edf3efc6100096e24aa8d1aec76bbde264f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Test-local config override headers were generated to paths missing
/tests/ infix, thus creating divergent tree in build output directory.
This patch fixes it moving generated config headers to the test-local
build directory.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Ic5f3ba287ba3e9f5897cbaac64e88c2809f52d73
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
There are cases where the RTC_VRT bit in register D stays set after a
power failure while the real date and time registers can contain rubbish
values (can happen when RTC is not buffered). If we do not detect this
invalid date and/or time here and keep it, Linux will use these bad
values for the initial timekeeper init. This in turn can lead to dates
before 1970 in user land which can break a lot assumptions.
To fix this, check date and time sanity when the RTC is initialized and
reset the values if needed.
Change-Id: I5bc600c78bab50c70372600347f63156df127012
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54914
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Already released Linux versions did not have the needed ACPI-extension
in the RTC driver. If the ACPI-Support is enabled for the RTC, this
older Linux will not be able to use this device as it will be claimed by
the PNP-drivers. As there is no way to avoid that an older Linux kernel
meets a newer coreboot in the field, we need to disable the ACPI
support for the RTC for the mc_apl-based mainboards.
Change-Id: I9f9939ba3234dc3654a4ef8a498649453941ebdf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55004
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In commit b64db833d6 a basic ACPI support was added to the driver.
With this support an SSDT-entry is created for this RTC and it is now
visible to the OS via ACPI. In Linux the PNP-devices, which are
reported over ACPI, are scanned rather early and if the entry is found,
the device is claimed even if there is no driver available yet.
In this case, when the native RTC-driver without ACPI-support is loaded
and tries to register this device, the RTC is already blocked by the
PNP-drivers and cannot be used anymore. This leads to a non-usable RTC
on kernels where the needed ACPI-extension is not yet merged into the
RTC driver.
This patch provides a way to disable the ACPI-support for the RTC if
needed.
Change-Id: Ic65794d409d13a78d17275c86ec14ee6f04cd2a6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55003
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The 64-bit compiler x86_64-linux-gnu-gcc-10 aborts the build with the
format warning below:
CC ramstage/cpu/x86/smm/smm_module_loader.o
src/cpu/x86/smm/smm_module_loader.c:415:42: error: format '%lx' expects argument of type 'long unsigned int', but argument 4 has type 'u32' {aka 'unsigned int'} [-Werror=format=]
415 | printk(BIOS_DEBUG, "%s: stack_end = 0x%lx\n",
| ~~^
| |
| long unsigned int
| %x
416 | __func__, stub_params->stack_top - total_stack_size);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| |
| u32 {aka unsigned int}
The size of `size_t` differs between i386-elf (32-bit) and
x86_64-elf/x86_64-linux-gnu (64-bit).
Unfortunately, coreboot hardcodes
src/include/inttypes.h:#define PRIx32 "x"
so `PRIx32` cannot be used.
There use `z` as length modifier, as size_t should be always big enough
to hold the value.
Found-by: x86_64-linux-gnu-gcc-10 (Debian 10.2.1-6) 10.2.1 20210110
Fixes: afb7a814 ("cpu/x86/smm: Introduce SMM module loader version 2")
Change-Id: Ib504bc5e5b19f62d4702b7f485522a2ee3d26685
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The 64-bit compiler x86_64-linux-gnu-gcc-10 aborts the build with the
format warning below:
CC ramstage/cpu/x86/smm/smm_module_loader.o
src/cpu/x86/smm/smm_module_loader.c: In function 'smm_module_setup_stub':
src/cpu/x86/smm/smm_module_loader.c:360:70: error: format '%lx' expects argument of type 'long unsigned int', but argument 5 has type 'unsigned int' [-Werror=format=]
360 | printk(BIOS_ERR, "%s: state save size: %zx : smm_entry_offset -> %lx\n",
| ~~^
| |
| long unsigned int
| %x
As `size_t` is defined as `long unsigned int` in i386-elf (32-bit), the
length modifier `l` matches there. With x86_64-elf/x86_64-linux-gnu
(64-bit) and `-m32` `size_t` is defined as `unsigned int` resulting in a
type mismatch. So, use the correct length modifier `z` for the type
`size_t`.
Found-by: x86_64-linux-gnu-gcc-10 (Debian 10.2.1-6) 10.2.1 20210110
Fixes: afb7a814 ("cpu/x86/smm: Introduce SMM module loader version 2")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Change-Id: I4172e0f4dc40437250da89b7720a5c1e5fbab709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The 64-bit compiler x86_64-linux-gnu-gcc-10 aborts the build with the
format warning below:
CC ramstage/cpu/x86/smm/smm_module_loader.o
src/cpu/x86/smm/smm_module_loader.c: In function 'smm_create_map':
src/cpu/x86/smm/smm_module_loader.c:146:19: error: format '%zx' expects argument of type 'size_t', but argument 3 has type 'uintptr_t' {aka 'long unsigned int'} [-Werror=format=]
146 | " smbase %zx entry %zx\n",
| ~~^
| |
| unsigned int
| %lx
147 | cpus[i].smbase, cpus[i].entry);
| ~~~~~~~~~~~~~~
| |
| uintptr_t {aka long unsigned int}
In coreboot `uintptr_t` is defined in `src/include/stdint.h`:
typedef unsigned long uintptr_t;
As `size_t` is defined as `long unsigned int` in i386-elf (32-bit), the
length modifier `z` matches there. With x86_64-elf/x86_64-linux-gnu
(64-bit) and `-m32` `size_t` is defined as `unsigned int` resulting in a
type mismatch. Normally, `PRIxPTR` would need to be used as a length
modifier, but as coreboot always defines `uintptr_t` to `unsigned long`
(and in `src/include/inttypes.h` also defines `PRIxPTR` as `"lx"`), use
the length modifier `l` to make the code more readable.
Found-by: x86_64-linux-gnu-gcc-10 (Debian 10.2.1-6) 10.2.1 20210110
Fixes: afb7a814 ("cpu/x86/smm: Introduce SMM module loader version 2")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Change-Id: I32bff397c8a033fe34390e6c1a7dfe773707a4e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
With commit 405f229689 (soc/intel/*: drop UART pad configuration from
common code) the UART pad configuration was dropped from common SoC
code. Through a second commit 5ff17ed393 (mb/siemens/mc_apl1: do UART
pad configuration at board-level) the UART pad configuration was made
for mc_apl1 baseboard. This change is also needed for all other mc_apl
boards.
Change-Id: If78726d9b141e4e7580cca3267f49c1a5b95d7fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Update FADT table per relevant PM settings:
Fix PM Timer block access size and disable C2 and C3 states for the CPU.
Further on, set the century byte offset in FADT to point to the common location in CMOS.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I72a57bf8ec61c3eabc4522c2695ae4b16979f188
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54958
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
fsp_temp_ram_exit() function is only getting called by
late_car_teardown() function inside temp_ram_exit.c file.
Hence, make function as static and removed from include/fsp/api.h.
Change-Id: I2239400e475482bc21f771d41a5ac524222d40fc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update devicetree and gpio driving of storo that enable stylus
Updates the GPIO configuration for GPP_C12 to
PAD_CFG_GPI_GPIO_DRIVER and device tree entry for PENH device to
use WAKEUP_ROUTE_GPIO_IRQ.
BUG=b:188519508,b:188365033
BRANCH=dedede
TEST=build bios and the pen behavior can be detected.
Change-Id: I2ffc969569b3ca29ba76326140f958a9707199f7
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On RW boot path psp_verstage call cbfs_map which calls chain of
_cbfs_alloc, cbfs_boot_lookup and cbfs_get_boot_device. Then
cbfs_get_boot_device initializes MCACHE which is used later.
However on RO boot path psp_verstage doesn't try to find anything in the
CBFS which results RO MCACHE not to be initialized. Add
cbfs_get_boot_device(true) to explicitly initialize MCACHE on recovery
boot.
BUG=b:177091575
BRANCH=none
TEST=build and boot jelboz
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I6c4b522fef5a4affd215faa122bdf6b53190cf3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54711
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some mainboards need a mainboard-specific mechanism to access option
values. Allow mainboards to implement the option API. Also, add some
documentation about the current option API, and describe when should
one reimplement the option API in mainboard code: only when the code
is mainboard-specific to comply with externally-imposed constraints.
Change-Id: Idccdb9a008b1ebb89821961659f27b1c0b17d29c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Intel CBnT (and Boot Guard) makes the chain of trust TOCTOU safe by
setting up NEM (non eviction mode) in the ACM. The CBnT IBB (Initial
BootBlock) therefore should not disable caching.
Sidenote: the MSR macros are taken from the slimbootloader project.
TESTED: ocp/Deltalake boot with and without CBnT and also a broken
CBnT setup.
Change-Id: Id2031e4e406655e14198e45f137ba152f8b6f567
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Over the last couple of years we have continuously added more and more
CBMEM init hooks related to different independent components. One
disadvantage of the API is that it can not model any dependencies
between the different hooks, and their order is essentially undefined
(based on link order). For most hooks this is not a problem, and in fact
it's probably not a bad thing to discourage implicit dependencies
between unrelated components like this... but one resource the
components obviously all share is CBMEM, and since many CBMEM init hooks
are used to create new CBMEM areas, the arbitrary order means that the
order of these areas becomes unpredictable.
Generally code using CBMEM should not care where exactly an area is
allocated, but one exception is the persistent CBMEM console which
relies (on a best effort basis) on always getting allocated at the same
address on every boot. This is, technically, a hack, but it's a pretty
harmless hack that has served us reasonably well so far and would be
difficult to realize in a more robust way (without adding a lot of new
infrastructure). Most of the time, coreboot will allocate the same CBMEM
areas in the same order with the same sizes on every boot, and this all
kinda works out (and since it's only a debug console, we don't need to
be afraid of the odd one-in-a-million edge case breaking it).
But one reproducible difference we can have between boots is the vboot
boot mode (e.g. normal vs. recovery boot), and we had just kinda gotten
lucky in the past that we didn't have differences in CBMEM allocations
in different boot modes. With the recent addition of the RW_MCACHE
(which does not get allocated in recovery mode), this is no longer true,
and as a result CBMEM consoles can no longer persist between normal and
recovery modes.
The somewhat kludgy but simple solution is to just create a new class of
specifically "early" CBMEM init hooks that will always run before all
the others. While arbitrarily partitioning hooks into "early" and "not
early" without any precise definition of what these things mean may seem
a bit haphazard, I think it will be good enough in practice for the very
few cases where this matters and beats building anything much more
complicated (FWIW Linux has been doing something similar for years with
device suspend/resume ordering). Since the current use case only relates
to CBMEM allocation ordering and you can only really be "first" if you
allocate in romstage, the "early" hook is only available in romstage for
now (could be expanded later if we find a use case for it).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If2c849a89f07a87d448ec1edbad4ce404afb0746
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We would like to have an easy way to completely disable TPM support on a
board. For boards that don't pre-select a TPM protocol via the
MAINBOARD_HAS_TPMx options, this is already possible with the
USER_NO_TPM option. In order to make this available for all boards, this
patch just removes the whole USER_TPMx option group and directly makes
the TPM1 and TPM2 options visible to menuconfig. The MAINBOARD_HAS_TPMx
options can still be used to select defaults and to prevent selection of
a protocol that the TPM is known to not support, but the NO_TPM option
always remains available.
Also fix some mainboards that selected TPM2 directly, which they're not
supposed to do (that's what MAINBOARD_HAS_TPM2 is for), and add a
missing dependency to TPM_CR50 so it is set correctly for a NO_TPM
scenario.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib0a73da3c42fa4e8deffecb53f29ee38cbb51a93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Since the default for the corresponding UPD of the Picasso FSP is
DXIO_PSPP_POWERSAVE and the devicetree default is DXIO_PSPP_PERFORMANCE,
add a deviectree setting for each board that's using the Picasso SoC
code to not change the setting for the existing boards.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0008ebb0c0f339ed3bdf24ab95a20aa83d5be2c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
hexdump and hexdump32 do similar things, but hexdump32 is mostly a
reimplementation that has additional support to configure the console
log level, but has a very unexpected len parameter that isn't in bytes,
but in DWORDs.
With the move to hexdump() the console log level for the hexdump is
changed to BIOS_DEBUG.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6138d17f0ce8e4a14f22d132bf5c64d0c343b80d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54925
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The only FSP 1.1 platform is Braswell, which has a non-weak definition
for the `soc_silicon_init_params` function. This changes the resulting
BUILD_TIMELESS=1 coreboot image for Facebook fbg1701, for some reason.
Change-Id: I2a1b51cda9eb21d7af8372c16a43195a4bdd9543
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The only FSP 1.1 platform is Braswell. Drop unused weak definitions for
functions where a non-weak definition always exists.
Tested with BUILD_TIMELESS=1, Facebook fbg1701 remains identical.
Change-Id: Ifaf40a1cd661b123911fbeaafeb2b7002559a435
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This allows boards to specify which PSPP policy (basically a dynamic
trade-off between power consumption and PCIe link speed) should be used
and also makes sure that the boards are using the expected PSPP policy
and not just the UPD default from the FSP binary that has already
changed once during the development.
BUG=b:188793754
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1b6459b2984711e72b79f5d4d90e04cb4b78d512
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54930
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TBT PowerResource _ON/_OFF methods are currently invoked by _PS0 and
_PS3 respectively. It is defined for ACPI driver to call _ON and _OFF
methods. This change drops the _PS0 and _PS3 call for _ON/_OFF and
returns TBT PowerResource declaration in the _PR0 and _PR3, then ACPI
driver will call the TBT PowerResource _ON and _OFF methods.
BUG=b:188891878
TEST=Traced both of TBT _ON and _OFF methods invocation and execution
at run time. Verified TBT's power_state to be D3Cold.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I398b3f58ec89f98673cbbe633149d31188ec3351
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Generic Initiator Affinity structure is introdcued in ACPI spec 6.3.
This structure is used to define NUMA affinity domain which is
established by generic initiator (such as by CXL device).
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Ic6ef01c59e02f30dc290f27e741027e16f5d8359
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
No board uses AMD PI 00630F01, so drop it. And drop a single reference
to the now-removed `NORTHBRIDGE_AMD_PI_00630F01` Kconfig option inside
the `drivers/amd/agesa/acpi_tables.c` file.
Change-Id: Ibc45a4a6041220ed22273c1d41f9b796e1acb901
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54897
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Microcode header supports advertising support for only one CPU
signature and processor flags. If there are multiple processor
families supported by this microcode blob, they are mentioned in
the extended signature table.
Add support to parse the extended processor signature table to
determine if the microcode blob supports the currently running CPU.
BUG=b:182234962
TEST=Booted ADL brya system with a processor whose signature/pf are
in the extended signature table of a microcode patch. Was able to
match and load the patch appropriately.
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: I1466caf4a4ba1f9a0214bdde19cce57dd65dacbd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
After Thunderbolt firmware is downloaded to IMR, its authentication
validity needs to be checked. This change implements the valid_tbt_auth
function. Thunderbolt DSD and its corresponding IMR_VAID will be
present to kernel only if its authentication is successful.
BUG=b:188695995
TEST=Validated TGL TBT firmware authentication and its IMR_VALID
into SSDT which is properly present to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I3c9dda341ae6f19a2a8c85f92edda3dfa08c917a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
After Thunderbolt firmware is downloaded to IMR, its authentication
validity needs to be checked. This change adds the TBT firmware IMR
status register offset and its authentication valid bit for
valid_tbt_auth function usage.
BUG=b:188695995
TEST=Built coreboot image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I742a00b6b58c45c1261f06b06a94346ad0a74829
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54888
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After Thunderbolt firmware is downloaded to IMR, its authentication
validity needs to be checked. This change adds the TBT firmware IMR
status register offset and its authentication valid bit for
valid_tbt_auth function usage.
BUG=b:188695995
TEST=Built Voxel coreboot image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia25827f18a10bf4d2dcabfe81565ac326851af3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54709
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Building google/sarien with a 64-bit compiler (x86_64-linux-gnu) fails
with the error below.
src/ec/google/wilco/mailbox.c: In function 'wilco_ec_transfer':
src/ec/google/wilco/mailbox.c:184:43: error: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type 'size_t' {aka 'unsigned int'} [-Werror=format=]
184 | printk(BIOS_ERR, "%s: data too short (%lu bytes, expected %zu)",
| ~~^
| |
| long unsigned int
| %u
185 | __func__, rs.data_size - skip_size, msg->response_size);
| ~~~~~~~~~~~~~~~~~~~~~~~~
| |
| size_t {aka unsigned int}
`data_size` has type `uint16_t`, and `skip_size` has type `size_t`,
whose size differs in 32-bit (unsigned int) and 64-bit (unsigned long).
So use the length modifier `z` for a `size_t` argument.
Found-by: x86_64-linux-gnu-gcc-10 (Debian 10.2.1-6) 10.2.1 20210110
Change-Id: Ida27323daeed9b8ff487302d0f3d6fcce0bbb705
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie
Coverity found resource leak in test setup function in error block.
Add malloc result check and free in error handling to silence Coverity.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Found-by: Coverity CID 1446760
Change-Id: Icf746df27167047fa3cf8f5df09fced20863f76d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Configure GPIO CAM_PDN5 (AP_XHCI_INIT_DONE) as output, so that
payloads (for example depthcharge) can assert it to notify EC to enable
USB VBUS.
BUG=b:187149602
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: I3bf63f91b8057e35be2780024a8b398c3044729b
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54902
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Incorrect size of the einj structure was being used, which created an
invalid checksum message by the OS. This patch fixes the issue.
Test=Booted to Linux on Deltalake mainboard and verified invalid checksum
message is not logged in syslog. Exact message -> 'ACPI BIOS Warning
(bug): Incorrect checksum in table [EINJ] - 0xDA, should be 0xD9'
Change-Id: I2b1722d6960d4a62d14fb02ac5e8838397e12f92
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54787
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
scan-build found a dead assignment, that the value stored to `res` is
never read. Use `pci_dev_read_resources()` instead, as done in
`sb/intel/common/smbus_ops.c` since commit 5f734327
(sb/intel/common/smbus_ops.c: Clean up read resources) avoiding the
assignment.
Change-Id: Ic59063b05a45dca411bf5b56c1abf3dd66ff0437
Found-by: scan-build (coreboot toolchain v0ad5fbd48d 2020-12-24 - clang version 11.0.0)
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54904
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ESPI_SLAVE_CHANNEL_READY is a read-only bit from the host perspective.
It is set when the eSPI peripheral has configured the channel.
We actually want to set the ESPI_SLAVE_CHANNEL_ENABLE flag. This never
caused an issue before because the peripheral channel is enabled by
default after PLTRST# is deasserted. This does fix the case where
periph_ch_en == 0. It now properly clears the enable flag.
BUG=b:188188172, b:188935533
TEST=Boot guybrush to OS, perform warm reset
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I24e0734d5652601ae9c967da528fec5e3f780991
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The ChromeEC might take longer than 1ms for the peripheral channel to be
enabled. The PLTRST# interrupt handler takes about ~539us.
This doesn't account for the time it takes for the interrupt handler
to be scheduled. Increasing the timeout to 10ms gives ample time.
BUG=b:188188172, b:188935533
TEST=Boot guybrush and no longer see channel enable errors
Suggested-by: Rob Barnes <robbarnes@google.com>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib6db577bf06175ceb17b446af706ad8c9f891481
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54788
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With the introduction of fw_config support in coreboot, it is possible
for mainboards to control the state of a device (on/off) in ramstage
using fw_config probe conditions. However, the device tree in
immutable in all other stages and hence `is_dev_enabled()` does not
really reflect the true state as in ramstage.
This change adds a call to `fw_config_probe_dev()` in
`is_dev_enabled()` when device tree is immutable (by checking
DEVTREE_EARLY) to first check if device is disabled because of device
probe conditions. If so, then it reports device as being
disabled. Else, dev->enabled is used to report the device state.
This allows early stages (bootblock, romstage) to use
`is_dev_enabled()` to get the true state of the device by taking probe
conditions into account and eliminates the need for each caller to
perform their own separate probing.
Change-Id: Ifede6775bda245cba199d3419aebd782dc690f2c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54752
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a helper function `fw_config_probe_dev()` that allows
the caller to check if any of the probe conditions are true for any
given device. If device has no probe conditions or a matching probe
condition, then it returns true and provides the matching probe
condition back to caller (if provided with a valid pointer). Else, it
returns false. When fw_config support is disabled, this function
always returns true.
Change-Id: Ic2dae338e6fbd7755feb23ca86c50c42103f349b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54751
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
`probe_list` member in `struct device` is present in all stages,
however, util/sconfig emits the list only when !DEVTREE_EARLY. This
change ensures that `probe_list` is emitted in all stages. In follow
up changes, this is used to get the correct device state using probe
conditions.
Change-Id: I61f7e909d48b616ac2127a5a9f36bdf4817a5165
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
fw_config is unprovisioned in the factory for the first boot. This is
the only case where fw_config is left unprovisioned. On first boot in
factory, fw_config gets correctly provisioned by the factory
toolkit. When fw_config is unprovisioned, it is not always possible to
make a guess which device to enable/disable since there can be certain
conflicting devices which can never be enabled at the same time. That
is the reason the original implementation of fw_config library kept
fw_config as 0 when it was unprovisioned.
CB:47956 ("fw_config: Use UNDEFINED_FW_CONFIG to mean unprovisioned")
added support for a special unprovisioned value to allow any callers
to identify this factory boot condition and take any appropriate
action required for this boot (Ideally, this would just involve
configuring any boot devices essential to getting to OS. All other
non-essential devices can be kept disabled until fw_config is properly
provisioned). However, CB:47956 missed handling the
`fw_config_probe()` function and resulted in silent change in behavior.
This change fixes the regression introduced by CB:47956 and returns
`false` in `fw_config_probe()` if fw_config is not provisioned yet.
Change-Id: Ic22cd650d3eb3a6016fa2e2775ea8272405ee23b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54750
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
commit ce0e2a0140 (drivers/intel/fsp2_0:
use FSP to allocate APEI BERT memory region) adds a mechanism to reserve
the BERT region inside the coreboot code, so we can get rid of the
workaround to reserve it in the FSP and return the location in a HOB.
mcfg->bert_size defaults to 0 which makes the FSP not generate the
corresponding HOB, but that field is planned to be removed at least on
Cezanne, so don't explicitly set it to 0.
BUG=b:169934025
TEST=BERT table that gets generated in a follow-up patch for Picasso
points to expected BERT region and Linux is able to access, decode and
display it.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaca89b47793bf9982181560f026459a18e7db134
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52584
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Most of the time when INIT_BOOTBLOCK is selected, the cache should be
empty here anyway, so this is a no-op. But when it's not empty that
means the bootblock loaded some other file before it got to the TPM
init part (which is possible, for example, if hooks like
bootblock_soc_init() load something).
Change-Id: I4aea86c094abc951d7670838f12371fddaffaa90
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
In order to fill out static entries for a _PRT table for
soc/intel/common, the PIRQ<->IRQ mapping is required. This patch adds
a function lpc_get_pch_pirq_routing() which returns this mapping.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib215fba54573c50a88aa4584442bd8d27ae017be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enable ASPM, Common Clock and Clock Power Managment. Accomplish this
by adding the options in the platform Kconfig as well as dxio
descriptors.
BUG=b:187743927
TEST=Boot to ChromeOS and see ASPM, CC and Clock PM enabled with lspci
Change-Id: I9d6e606763798afc6b797d7d24ee7cae09f9e33f
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54681
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable ASPM, Common Clock and Clock Power Managment. Accomplish this
by adding the options in the platform Kconfig as well as dxio
descriptors.
BUG=b:187743927
TEST=Boot to ChromeOS and see ASPM, CC and Clock PM enabled with lspci
Change-Id: Iefc4b5b489cb8caf59f21dd4333d7af66ba47c32
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54282
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UI monitors this input event and sends global mic mute command to CRAS
when the physical switch is toggled.
BUG=b:184593945
BRANCH=puff
TEST=build image and verify with evtest on DUT.
Apply crrev.com/c/2870806 with chrome cmdline flag and verify global
mute is triggered.
Verify sequences of switch toggle and suspend/resume.
Change-Id: Id89947885fdd96c5b5d598bda6db127daf298dc3
Signed-off-by: Ben Zhang <benzh@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Added SW_MUTE_DEVICE event type for mic mute switch.
BUG=b:184593945
BRANCH=puff
TEST=build image and verify with evtest on puff:
/dev/input/event3: mic_mute_switch
UI event_device_info receives the proper name.
Change-Id: I09c52dc3df63e266c73741b102a22f8a2b896791
Signed-off-by: Ben Zhang <benzh@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Added the label field to the gpio_keys _DSD so that the kernel driver
can use a meaningful name instead of the generic _HID PRP0001.
BUG=b:184593945
BRANCH=puff
TEST=build image and verify with evtest on puff:
/dev/input/event3: mic_mute_switch
UI event_device_info receives the proper name.
Change-Id: I0377851b9cf23bab31930aed6e7de91b4ac3505b
Signed-off-by: Ben Zhang <benzh@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The mainboard.c guard was only added to preserve reproducibility when
unifying the boards. The `install_intel_vga_int15_handler` function does
nothing when `VGA_ROM_RUN` is not selected. Remove the guard and always
select `INTEL_INT15` for simplicity.
Change-Id: If38ca49dba81921a3e7abe22542ae74d8914a38d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
To preserve reproducibility, temporarily guard mainboard.c contents.
Tested with BUILD_TIMELESS=1, coreboot.rom for the Asus P8Z77-M PRO
remains identical when not adding the .config file in it.
Change-Id: I05e272690ca78f6b9e22b1db1c36cb9e5a7afe3c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Get ready to squash all Asus Z77 boards together, so as to factor out
some redundant code.
Tested with BUILD_TIMELESS=1, coreboot.rom for the Asus P8Z77-V LX2
remains identical when not adding the .config file in it.
Change-Id: I701ec4adbc65732ffc0a60d311bf07bf7f414ebf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The mainboard.c guard was only added to preserve reproducibility when
unifying the boards. The `install_intel_vga_int15_handler` function does
nothing when `VGA_ROM_RUN` is not selected. Remove the guard and always
select `INTEL_INT15` for simplicity.
Change-Id: If51a0ab1c57b0856018a62cf669e5d1b53e5333c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
I added these devicetrees in commit 65ddbb720b (mb/asus/p8h61-m_pro:
Add new mainboard) and commit fe7c2b996b (mb/asus/p8h61-m_lx3_r2_0:
Add new mainboard). To ease licensing matters when transforming these
boards to use overridetrees, relicense the devicetrees so that all of
them use the GPL-2.0-or-later license.
Change-Id: Id26d0d9dd6cbb81d6a6a263feab7f36ddb4ff6e6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Handle some differences in the DSDT code using preprocessor.
Tested with BUILD_TIMELESS=1, coreboot.rom for the Asus P8H61-M LX
remains identical when not adding the .config file in it.
Change-Id: I2a02f32dfd9fa9c1adce3baf0d279ea19db5883f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The time constant values were taken from the zork thermal.asl.
BUG=b:186166365
TEST=Boot guybrush to OS and verify logs look correct
thermal-0294 thermal_trips_update : Found critical threshold [3641]
thermal-0321 thermal_trips_update : No hot threshold
thermal-0200 thermal_get_temperatur: Temperature is 3060 dK
thermal-0219 thermal_get_polling_fr: Polling frequency is 100 dS
thermal-0200 thermal_get_temperatur: Temperature is 3060 dK
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [TM00] (33 C)
thermal-0200 thermal_get_temperatur: Temperature is 3070 dK
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iaeed75bdaa16b117d0fa7144ede98db1388f74f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This adds the required method to access temperature data from the
ChromeEC.
BUG=b:186166365
TEST=Boot guybrush to the OS and verify temperatures
$ tail /sys/devices/virtual/thermal/thermal_zone*/temp
==> /sys/devices/virtual/thermal/thermal_zone0/temp <==
31900
==> /sys/devices/virtual/thermal/thermal_zone1/temp <==
34900
==> /sys/devices/virtual/thermal/thermal_zone2/temp <==
31900
==> /sys/devices/virtual/thermal/thermal_zone3/temp <==
33900
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I418b6691a7d00a4c2d89c9c1fe8f9416602be0f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54133
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct the Realtek ALC3254 codec name in the comment. The name is used
in the original commit message, and is also present in the Linux kernel
(`sound/pci/hda/patch_realtek.c`).
The file was an exact copy of
`src/mainboard/google/sarien/variants/arcada/include/variant/hda_verb.h`
added in commit 95370e1f (mb/google/sarien: Add HD Audio verb table).
Change-Id: I43cd73a14e07eb4518e3d44b6f81dff5016da721
Fixes: e3443d87 ("mb/google/drallion: Add new mainboard")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Correct the Realtek ALC3254 codec name in the comment. The name is used
in the original commit message, and is also present in the Linux kernel
(`sound/pci/hda/patch_realtek.c`).
Change-Id: Id8a099297bd8bcebf9734e1beee2449fdcca75c5
Fixes: 95370e1f ("mb/google/sarien: Add HD Audio verb table")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54589
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Enable AMD I2S machine driver and configure the devicetree with HID
information so that the machine driver ACPI objects can be passed to the
kernel. Also configure Audio Co-processor(ACP) to operate in I2S TDM mode.
BUG=b:187860242
TEST=Build and boot to OS in Guybrush. Ensure that the ACPD device is
enabled in the appropriate scope in SSDT.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I528f90d81a418236e512a1e0840ff44c3a3a983e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Move discrete TPM in the devicetree to avoid emitting the following
message: "Using default TPM ACPI path: '\_SB_.PCI0.LPCB'"
There is no corresonding ACPI device for 1f.5 PCI device. Therefore,
move the discrete TPM to a device that has the corresponding ACPI
device node. Functionality should remain the same.
BUG=b:187518267
Change-Id: Ie9ec70336d5651c87f06f8b357abd1bfdb1cc06b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Fix the exclusion path for lcov; it should exclude the directory
with source code, not object files.
Use the COV environment variable to
* control whether we build for coverage or not
* select the output directory
Add a separate target for generating the report, so we can get a
report for all of the tests together or just a single test.
Add documentation.
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: I2bd2bfdedfab291aabeaa968c10b17e9b61c9c0a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
When performing an in-band reset the host controller and the
peripheral can have mismatched IO configs.
i.e., The eSPI peripheral can be in IO-4 mode while, the
eSPI host will be in IO-1. This results in the peripheral
getting invalid packets and thus not responding. This causes the
NO_RESPONSE status bit to be set and cause eSPI init to fail.
If the peripheral is alerting when we perform an in-band
reset, there is a race condition in espi_send_command.
1) espi_send_command clears the interrupt status.
2) eSPI host controller hardware notices the alert and sends
a GET_STATUS.
3) espi_send_command writes the in-band reset command.
4) eSPI hardware enqueues the in-band reset until GET_STATUS
is complete.
5) GET_STATUS fails with NO_RESPONSE and sets the interrupt
status.
6) eSPI hardware performs in-band reset.
7) espi_send_command checks the status and sees a
NO_RESPONSE bit.
As a workaround we allow the NO_RESPONSE status code when
we perform an in-band reset.
BUG=b:186135022
TEST=suspend_stress_test and S5->S0 tests on guybrush and zork.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I71271377f20eaf29032214be98794e1645d9b70a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Rob Barnes <robbarnes@google.com>
I'm not 100% sure if this should rather be duplicated from Picasso or
commonized. Checked with the docs and this won't be compatible with
Stoneyridge and one future product's PPR lacked the corresponding
register. Some other chip has a compatible register layout, but a
different number of PCIe GPP clock outputs, so the common code would
need to use some SoC-dependent defines and possibly a SoC-specific
lookup table for the mapping which is also not that great.
TEST=Checked Cezanne PPR
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b6d0cb8d7eb0288d8a18fcb975dc377b2c6846a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54685
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to use the USB WWAN module in USB mode (as opposed to PCIe),
the PCIe RP must be turned off at the FSP level. The `probe` statement
in the devicetree unfortunately takes effect too late, because the UPDs
for disabling/enabling PCIE RP belong to FSP-M (romstage), whereas
fw_config probing for devicetree is done in ramstage.
Add a new variant-specific file which will handle manually setting the
UPD based on FW_CONFIG instead.
BUG=b:180166408
TEST=set CBI FW_CONFIG field to LTE_USB, see message in console,
set field to LTE_PCIE, do not see message in console.
Change-Id: Ica2f64ec99fa547e233012dc201577a14f6aa7d7
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54633
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot needs to access EC RFWU entry in order to suspend and resume PD
and modes setting. This change adds ec_retimer_fw_update implementation
for retimer firmware upgrade.
BUG=b:186521258
TEST=Build image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ib937d8bd72fc39487854773573b435bf2add672a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52713
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This changes updates mainboard properties by adding DFP number, PLD
and power_gpio for each DFP.
BUG=b:186521258
TEST=Validated Retimer firmware upgrade along with upstream kernel under
no device attached scenario.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I18f29ce5f8450a8b0f8208a60b8b607f9f0d8817
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52714
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Along with upstream kernel for Retimer firmware upgrade, coreboot
provides DFPx under host router where each DFP has its PLD and DSM. The
DFPx's functions encapsulates power control through GPIO, PD
suspend/resume and modes setting for Retimer firmware update under NDA
scenario.
BUG=b:186521258
TEST=Booted to kernel and validated host router's DFPx properties after
decomposing SSDT table.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I81bef80729f6df57119f5523358620cb015e5406
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52712
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Along with upstream kernel for Retimer firmware update, coreboot defines
power control for each DFP respectively under host router. This change
removes the power_gpio from the baseboard. Individual DFPx power_gpio
will be added once the dependent definition is complete.
BUG=b:186521258
TEST=Build image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I819d2900afabbfdb2713fa8eee35d3c90cb904fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Along with upstream kernel for Retimer firmware update, coreboot defines
power control for each DFP respectively under host router. This change
removes the power_gpio from baseboard. Individual DFPx power_gpio will
be added once the dependent definition is complete.
BUG=b:186521258
TEST=Build image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Iec2437ab20d283d080752a80aa4514aa9af6897e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52711
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Along with upstream kernel for Retimer firmware update, coreboot changes
the ec_retimer_fw_update format. This change removes this API and will
add implementation later once the dependent definition is complete.
BUG=b:186521258
TEST=Build image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I2d074b84fb3cb87b443871104b72b6c316af5279
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
We were not adding power management handling of GPIO_COM3 in gpio.asl
This can affect s0ix flow where platform won't go into s0ix since
GPIO_COM3 is not power gated.
BUG=b:188392183
BRANCH=None
TEST=Platform should enter to s0ix and GPIO COMM3 should not block an
entry to s0ix.
Change-Id: I3f269c66bdd6337adb0d2bd29d0b7d72ced19ec4
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
We recently added GPIO definition for PCIE vGPIO for Alder Lake.
We also need to disable GPIO dynamic PM for this community which is
already done for other communities as well.
BUG=b:188392183
BRANCH=None
TEST=Code compiles and Check if dynamic PM for GPIO COMM3 is also
disabled
Change-Id: I2f8645b8f4a9995e727a7623af97531c5de52892
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54383
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The new kernel secdata v1 stores the last read EC hash, and reboots the
device during EC software sync when that hash didn't match the currently
active hash on the EC (this is used with TPM_CR50 to support EC-EFS2 and
pretty much a no-op for other devices). Generally, of course the whole
point of secdata is always that it persists across reboots, but with
MOCK_SECDATA we can't do that. Previously we always happened to somewhat
get away with presenting freshly-reinitialized data for MOCK_SECDATA on
every boot, but with the EC hash feature in secdata v1, that would cause
a reboot loop. The simplest solution is to just pretend we're a secdata
v0 device when using MOCK_SECDATA.
This was encountered on using a firmware built with MOCK_SECDATA but had
EC software sync enabled.
BUG=b:187843114
BRANCH=None
TEST=`USE=mocktpm cros build-ap -b keeby`; Flash keeby device, verify
that DUT does not continuously reboot with EC software sync enabled.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: Id8e81afcddadf27d9eec274f7f85ff1520315aaa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
To preserve reproducibility, temporarily guard mainboard.c contents.
This will be removed once all boards have become variants.
Tested with BUILD_TIMELESS=1, coreboot.rom for the Asus H61M-CS
remains identical when not adding the .config file in it.
Change-Id: I1ffb41470d24713a4a7f0689958b733d4b1bdf52
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Get ready to squash all Asus H61 boards together, so as to factor out
lots of redundant code.
Tested with BUILD_TIMELESS=1, coreboot.rom for the Asus P8H61-M LX3 R2.0
remains identical when not adding the .config file in it.
Change-Id: I738197bf4d5ea8b879ae26ecbcb0cf3714316662
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Commit 65ddbb720b (mb/asus/p8h61-m_pro: Add new mainboard) added this
file, and I authored this commit. Since most gma-mainboard.ads files are
licensed as GPL-2.0-or-later, relicense this one for consistency.
Change-Id: I2d28150f4c97ba600cb46fead7bb29cdc65c5baf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54362
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mainboards with variants may not always use the same cmos.layout file.
Turn the hardcoded path into a Kconfig symbol to allow changing it.
Tested with BUILD_TIMELESS=1: Without including the config file in the
coreboot.rom and with `USE_OPTION_TABLE` selected, building for the Asus
P8H61-M PRO produces an identical coreboot image.
Change-Id: I4cc622dcb70855c06cb8a816c34406f8421180df
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54366
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Definition for NAV_FWE BIT was added in commit e6e8b3d
Even if try to set this BIT it was not getting set since PAD_CFG_DW0
mask will make it 0 since this bit was not part of mask.
Adding NAV_FWE to mask will resolve this issue and BIT will be set/unset
as per programming in mainboard.
TEST=Check GPIO register dump and see if BIT is getting set properly.
Change-Id: I970ae81ed36da45c3acc61814980b2e6ff889445
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54350
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot test targets help section was missing an empty line at the end.
This caused the next help section to be visually merged with it.
Empty line makes help output more aesthetic.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I2f7202b0a636f62b60788215058611c9c86183de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Coverity reported unitialized array spd_block.addr_map which values are
not used. Add initialization to silence Coverity and avoid errors in
the future.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Found-by: Coverity CID 1453145 1453146 1453147 1453148 1453149
Change-Id: If301f9e5d9e06ad26769bd0717f1f906e620d82d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Enable/disable LTE function based on LTE bit of FW_CONFIG.
The LTE function settings are included GPIO settings, USB port settings and
power off sequence.
BUG=b:187797408
BRANCH=dedede
TEST=Build and test the change on cret.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib926e99aaf9df433a7cff71180ee55431d69f718
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The `tcrt` and `tpsv` values in GNVS can be used to implement thermal
management in ACPI. However, not all mainboards use these values.
On mainboards where `tcrt` and `tpsv` are not used in ACPI tables and
are the only values set in the `mainboard_fill_gnvs` function, remove
them as well as the entire `acpi_tables.c` file. Most files come from
autoport, which unconditionally generates this file.
Change-Id: If2315ddd9700e2da0a24ffecc20acb5c1a1d688e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
PSP_SOFTFUSE_BITS used to be like this:
15 0 29 "28 6"
It causes internal shell report error:
/bin/sh: -c: line 0: unexpected EOF while looking for matching `"'
/bin/sh: -c: line 1: syntax error: unexpected end of file
/bin/sh: -c: line 0: unexpected EOF while looking for matching `"'
/bin/sh: -c: line 1: syntax error: unexpected end of file
Change-Id: I716f19d37fb57b9ef3fc7259c6dcca7d21022d32
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
DisableDimmMc0Ch0 upds changed to DisableMc0Ch0 in new FSP releases. The definition
of the upd also changed. Changed FSP meminit code to work based on new definition of the UPDs.
Before:
0:Enable both DIMMs, 1:Disable DIMM0, 2:Disable DIMM1, 3:Disable both DIMMs
After:
0:Enable, 1:Disable
TEST=Boot to OS
Cq-Depend: chrome-internal:3831865, chrome-internal:3831864, chrome-internal:3831913
Cq-Depend: chromium:TODO
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I5af11ae99db3bbe3373a9bd4ce36453b58d62fec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54036
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The headers added are generated as per FSP v2162_00.
Previous FSP version was v2117_00.
Changes Include:
- Adjust UPD Offset in FspmUpd.h and FspsUpd.h
- Remove DisableDimmMc*Ch* Upds in FspmUpd.h
- Add DisableMc*Ch* Upds in FspmUpd.h
- Few UPDs description update in FspmUpd.h and FspsUpd.h
Change DisableDimmMc*Ch* to DisableMc*Ch* in meminit.c to avoid
compilation failure other change related to UPDs name change will be
part of next patch in relation chain.
BUG=b:187189546
BRANCH=None
TEST=Build and boot ADLRVP using all the patch in relation chain.
Change-Id: Ic8d7980146f1bfc96472ef504cf9f16eee63a13e
Cq-Depend: chrome-internal:3831865, chrome-internal:3831864, chrome-internal:3831913
Cq-Depend: chromium:TODO
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54083
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit has coreboot create the Chrome OS Firmware Management
Parameters (FWMP) space in the TPM. The space will be defined and the
contents initialized to the defaults.
BUG=b:184677625
BRANCH=None
TEST=emerge-keeby coreboot
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I1f566e00f11046ff9a9891c65660af50fbb83675
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Andrey Pronin <apronin@chromium.org>
The name `set_space()` seems to imply that it's writing to a TPM space
when actually, the function can create a space and write to it. This
commit attempts to make that a bit more clear. Additionally, in order
to use the correct sizes when creating the space, this commit also
refactors the functions slightly to incorporate the vboot context object
such that the correct sizes are used. The various vboot APIs will
return the size of the created object that we can then create the space
with.
BUG=b:184677625
BRANCH=None
TEST=`emerge-keeby coreboot`
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I80a8342c51d7bfaa0cb2eb3fd37240425d5901be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54308
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit updates the vboot submodule from commit 57c0c5b:
cgpt: Move all GPT on SPI-NOR infra behind a flag
to e681c37:
change node locked version expectations
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: Ifd130e3f66f1819f59f00703f0ad0c2278b544bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Updating from commit id 7ad39818b:
2020-10-12 09:16:21 +0000 - (Merge "mediatek: mt8192: add GIC600 support" into integration)
to commit id 96404aa27:
2021-05-13 18:27:27 +0200 - (Merge "build(hooks): update Commitizen to ^4.2.4" into integration)
This brings in 861 new commits.
Change-Id: I912545022e4320b86ab8a382144c02e315d0c835
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
TCSS OC pins have not been correctly configured for volteer.
This patch fills the value from devicetree to correct the OC pins
mapping.
BUG=b:184660529
BRANCH=None
TEST="emerge-volteer coreboot chromeos-bootimage", flash volteer2 and
verify CpuUsb3OverCurrentPin UPDs get set correctly.
Change-Id: I12da755a1d3b9ec3ed0a2dbfb0782313dd49c7e9
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
We need to change OC pin for type C USB3 ports and it depends
on the board design. Allowing it to be filled by devicetree will
make it easier to change the mapping based on the board design.
BUG=b:184660529
TEST="emerge-volteer coreboot" compiles without error.
Change-Id: I5058a18b1f4d11701cebbba85734fbc279539e52
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
I suspect there is additional initialization required to enable the
8042 keyboard controller on the EC. By removing the range we no longer
encounter long 20 second delays when reading the IO ports. Since
depthcharge polls the IO ports it makes it seem like depthcharge locked
up.
BUG=b:182100027
TEST=Boot majolica with depthcharge to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I56a7eb4200e4615e1b4d9f14594d64f93e031a54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
GPIO communities 0, 1, and 4 have virtual wire indexes & bits for at
least some of their groups; add the known information into the community
definitions. This patch is ported form tigerlake.
Change-Id: I2f1e2413d06e8afe4233d7111763cb45b78f845b
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add initial HMAT (Heterogeneous Memory Attribute Table) support based
on ACPI spec 6.4 section 5.2.27.
Add functions to create HMAT table (revision 2) and create HMAT Memory
Proximity Domain Attribute (MPDA) Structure.
TESTED=Simulated HMAT table creation on OCP DeltaLake server, dumped
the HMAT table and exmained the content. HMAT table and one MPDA
structure are added.
OCP Delatake server is based on Intel CooperLake Scalable Processor
which does not support CXL (Compute Express Link). Therefore solution
level testing is not done.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: I5ee60ff990c3cea799c5cbdf7eead818b1bb4f9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This is the DRAM initialization code from the reference
implementation released by Mediatek for MT8195.
The DRAM calibration code can be taken as a standalone
library, used by different boot loaders for initializing
DRAM and following a different coding style (coreboot was
using Linux Kernel coding style), so we have to put it
in vendor code folder.
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.com>
Change-Id: Iada3ec5ae8a39a8e9253caba550c834d486dddcd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
By default, FSP disables the GFX HDA. Enable it to support HDMI Audio
functionality.
BUG=b:186479763
TEST=Build and boot to OS in guybrush. Ensure that the GFX HDA is
enumerated in lspci output.
04:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Device 1637
Change-Id: I42cb26c44bbca3d937c5d52736c42468139f7b07
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54100
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The CBFS mcache size default was eyeballed to what should be "hopefully
enough" for most users, but some recent Chrome OS devices have already
hit the limit. Since most current (and probably all future) x86 chipsets
likely have the CAR space to spare, let's just double the size default
for all supporting chipsets right now so that we hopefully won't run
into these issues again any time soon.
The CBFS_MCACHE_RW_PERCENTAGE default for CHROMEOS was set to 25 under
the assumption that Chrome OS images have historically always had a lot
more files in their RO CBFS than the RW (because l10n assets were only
in RO). Unfortunately, this has recently changed with the introduction
of updateable assets. While hopefully not that many boards will need
these, the whole idea is that you won't know whether you need them yet
at the time the RO image is frozen, and mcache layout parameters cannot
be changed in an RW update. So better to use the normal 50/50 split on
Chrome OS devices going forward so we are prepared for the eventuality
of needing RW assets again.
The RW percentage should really also be menuconfig-controllable, because
this is something the user may want to change on the fly depending on
their payload requirements. Move the option to the vboot Kconfigs
because it also kinda belongs there anyway and this makes it fit in
better in menuconfig. (I haven't made the mcache size
menuconfig-controllable because if anyone needs to increase this, they
can just override the default in the chipset Kconfig for everyone using
that chipset, under the assumption that all boards of that chipset have
the same amount of available CAR space and there's no reason not to use
up the available space. This seems more in line with how this would work
on non-x86 platforms that define this directly in their memlayout.ld.)
Also add explicit warnings to both options that they mustn't be changed
in an RW update to an older RO image.
BUG=b:187561710
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I046ae18c9db9a5d682384edde303c07e0be9d790
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
While memcpy(foo, bar, 0) should be a no-op, that's hard to prove for a
compiler and so gcc 11.1 complains about the use of an uninitialized
"bar" even though it's harmless in this case.
Change-Id: Idbffa508c2cd68790efbc0b4ab97ae1b4d85ad51
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Create the correct MTRR solution based on the physical address space
provided by RESOURCE_ALLOCATOR_V4. Previously CPU initialization did not
account for lost C6 DRAM storage MTRR during postcar frame creation.
The BSP on 2GB has been stripped from UC MTRR covering C6 DRAM and
overlapping with usable DRAM WB MTRR. However this UC MTRR remained on
APs which caused inconsistent MTRRs warning in Linux. Use generic MTRR
function to create correct MTRR solution that propagates to APs. This
also fixes the inconsistent MTRRs warning.
TEST=boot Debian with Linux 4.14 on apu2 4GB ECC and apu3 2GB no-ECC
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Ie2d7a75affd7d3d3a1bc6327fb423e206b28562f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52762
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Select touchscreen(s) based on touchscreen source provisioned in SSFC of CBI (higher 32 bits of FW_CONFIG in coreboot).
The reason is to avoid to enable multiple touchscreen ICs with the same slave address.
BUG=b:186609348
TEST=build and boot to OS.
Change-Id: I087ea677a8865fc8c5b3f7c9773bd7f97924dbb3
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Drop the deprecated COREBOOTPAYLOAD option, and replace it with MrChromebox's
updated UefiPayloadPkg option. Simplify the Kconfig options to make it easier
to build from upstream edk2 master. Drop the TIANOCORE_USE_8254_TIMER Kconfig
option since it applied only to CorebootPayloadPkg. Clean up the Makefile now
that we're only building from a single Tianocore package/target.
Test: build/boot qemu Q35 target with both UefiPayload and Upstream options.
Change-Id: If545fbd0c30be6dcc6ff43107b80980fa23a527e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54019
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Hermes can be used with either CSME or SPS firmware. However, the SPS
(Server Platform Services) firmware does not support ACPI S3 and S4
sleep states, and coreboot should not report S3 and S4 as supported.
Add a Kconfig option to be selected when building coreboot to use with
SPS firmware, which allows disabling ACPI S3 and S4 sleep state support.
Change-Id: I9d0fa8530e198e86415f92da6719d2fb0d2401ec
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
vpp_sel and ethdr_sel are vdosys clock source select mux.
Steps to change to support 4K source.
1. Change vpp_sel source to mainpll_d4 to run at 546MHz
2. Change ethdr_sel source to univpll_d6 to run at 416MHz
Signed-off-by: Nancy Lin <nancy.lin@mediatek.com>
Change-Id: Ib6518ed6204528489c41e7161534bbd3734ac851
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54082
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds support for convertible devices to support different maximum
power and thermal configurations. The dynamic power and thermal
configuration (DPTC) via ACPI ALIB calls allows to change the parameters
during runtime. This code contains the assumption that
\_SB.PCI0.LPCB.EC0.TBMD exists when ACPI code calls the DPTC method. At
the moment only chromeec declares EC0.TBMD, but it's also the only code
that calls the DPTC method. The definition of DPTC_INPUTS isn't moved to
the common code directory, since it's currently unsure if we might need
to configure more than those 4 parameters for Cezanne.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ibdfc056cb325a32d87505dd93e01c9af81dfd6c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Some tests require to change kconfig symbols values to cover the code.
This patch enables one to set these vaues using <test-name>-config
variable.
Example for integer values.
timestamp-test-config += CONFIG_HAVE_MONOTONIC_TIMER=1
Example for string values. Notice escaped quotes.
spd_cache-test-config += CONFIG_SPD_CACHE_FMAP_NAME=\"SPD_CACHE_FMAP_NAME\"
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I1aeb78362c2609fbefbfd91c0f58ec19ed258ee1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
In order to support wake on WLAN events, configure the wake resource.
BUG=b:186011392
TEST=Build and boot to OS in guybrush. Ensure that WiFi power resource
is added to SSDT.
Device (\_SB.PCI0.GP20.WF00)
{
Name (_UID, 0x38B82CBC) // _UID: Unique ID
Name (_DDN, "WIFI Device") // _DDN: DOS Device Name
Name (_ADR, 0x0000000000000000) // _ADR: Address
}
Scope (\_SB.PCI0.GP20.WF00)
{
Name (_PRW, Package (0x02) // _PRW: Power Resources for Wake
{
0x08,
0x03
})
}
Change-Id: Ic238d9606aea20c058e9b47093693f10b14e6288
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Cezanne PSP is missing implementations for some svc apis. Do not
include files related to missing svc apis.
This CL should be reverted after the cezanne PSP supports these
functions.
BUG=b:187906425
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ibaab4e8435624d403ef18e980146ebfd1598b61b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Update the iasl path finding code to use XGCCPATH if it's set, and to
look for iasl on the path if it's not set and not under util/crossgcc.
On the jenkins builders, iasl is in the path, not in util/crossgcc/xgcc.
On the systems of people who have multiple copies of coreboot, it makes
sense to just have a single copy of the toolchain and define XGCCPATH in
the environment to point to it.
Previously, either of these situations resulted in a warning from the
genbuild_h tool that iasl was not found under util/crossgcc, which was
true, but not particularly relevant, and generated confusion.
If xcompile already existed before make was run, the correct path would
be found, but on an initial build, this check couldn't find iasl.
BUG=None
TEST=Build with iasl in /util/crossgcc/xgcc/bin, in the path and in a
directory pointed to with XGCCPATH.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ic2f8dca0be8bfb54d3c672fab6cf6f005bb394c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
genbuild_h was being run on every make invocation - clean, distclean,
etc. to get the source date epoch value. This value isn't used unless
a build is being done, so don't run it on non-compile make invocations.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I2afc0affc17116e0db849ea968474bc19dbb0ae1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add audio codec module RT5682 in project and define GPIO_137 in the
override_table for SSFC framework to adjust IRQ configuration.
BUG=b:182221327
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682I or DA7219 then check whether device tree is updated correspondingly by disabling unselected one.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I202f71f57ad2db84fb90b52f9ffd7a1fd05494a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Remove obsolete resource assigning functions. IO and MMIO address
registers are currently set by amd_initcpuio to cover whole PCI hole
under 4G to MMIO and IO 0x0000-0xFFFF is configured to be routed to
southbridge already. Use generic PCI and resource allocation functions
wherever possible to set northbridge resources.
TEST=boot Debian with Linux 4.14 on apu2 4GB ECC and apu3 2GB no ECC
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I8dd5e40bce513c5ba7f1d42a06e7ab0846666942
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Create the chronicler variant of the volteer reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:187318819
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_CHRONICLER
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Iebfea87b7c4cfc2a83e88a6c479a0842774ae018
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
We need to configure CPU PCIE root port related gpios in early
boot block stage for CPU root ports to work due to the dependency on
FSP-M PCIe configuration. Since we're removing this programming from
FSP, coreboot needs to take care of programming this GPIOs. Also we
need to enable virtual wire messaging for native gpios for CPU PCIE
root ports.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I27c898943471d834bd82e3c7e8b36cceb12de099
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52865
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
HSBIAS_SENSE_EN configures HSBIAS output current sense through
the external 2.21-k resistor. HSBIAS_SENSE is hardware feature to reduce
the potential pop noise during the headset plug out slowly. But on some
platforms ESD voltage will affect it causing test to fail, especially
with CTIA headset type. For different hardware setups, a designer might
want to tweak default behavior.
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Change-Id: I87c6f01af1bdb5b1cb8e399191519598d7fbe9ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52981
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since we want commits to go through 24 hours of review, move the
vboot list update a week earlier. Also point more directly at the
right script to execute.
Change-Id: I49e6dfe22894402d5a0526588f8a04595ac88862
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
List of changes:
1. Make the FSP notify phases name prior in comments section.
2. Fix discrepancies in FSP notify before and after postcode comments.
3. Add FSP notify postcode macros for after pci enumeration(0xa2)
and ready to boot(0xa3) call.
Change-Id: Ib4c825d5f1f31f80ad2a03ff5d6006daa7104d23
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52894
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ADL-M LP4 RVP has command mirror enabled and we need to fill correct
value of this UPD to pass the MRC.
Also, Value of TxDqDqsRetraining is set to 1 by default and we need to
disable it for only ADL-M LP5 RVP.
BUG=None
BRANCH=None
TEST=UPD values has been pass correctly and MRC passes on LP4/LP5 board
Change-Id: I3e16b9a3d3e6a92dacba9d38782df408596ed5e1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Soft straps, that can be configured by the vendor in the Intel Flash
Image Tool (FIT), can influence some pads' default state. It is possible
to select either a native function or GPIO mode for some pads on
non-server SoCs, while on server SoCs most pads can be controlled.
Thus, add a recommendation to always configure all pads for a board to
guarantee integrity between different board or vendor firmware revisions
where the soft straps might have been changed.
Change-Id: I33063a3f6a1c9cd5267d85f7da84deb554489a26
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Intel PDGs starting from Skylake / Sunrise Point state that, different
from the general recommendation in digital electronics, unconnected
GPIOs defaulting to GPIO mode do explicitly not require termination.
The reason for this is, that these GPIOs have the `GPIORXDIS` bit set,
which effectively disconnects the pad from the internal logic by
disabling the input buffer.
This bit - besides `GPIOTXDIS` - can also be set explicitly by using
the gpio macro `PAD_NC(pad, NONE)`.
In some cases, a pull resistor may be required due to bad board design
or when a vendor sets the RX/TX disable bits together with a pull
resistor and schematics are not available to check if the pad is really
unconnected or just unused. In this case the pull resistor should be
kept.
Pads defaulting to native functions usually don't need special handling.
However, when pads requiring external pull-ups are missing these due to
bad board design, they should be configured with `PAD_NC` to disconnect
them internally.
Rewrite the documentation to reflect these new findings.
Also clarify the comment in soc/intel gpio code accordingly.
Change-Id: Id01b197ebe8f2b8bb4ecf3d119ec2298b26d9be0
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52139
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is still causing boot errors on zork:
coreboot-4.13-3659-g269e03d5c42f Fri May 7 22:03:11 UTC 2021 bootblock starting (log level: 8)...
Family_Model: 00820f01
PSP boot mode: Development
Silicon level: Pre-Production
Set power off after power failure.
PMxC0 STATUS: 0x800 BIT11
I2C bus 3 version 0x3132322a
DW I2C bus 3 at 0xfedc5000 (400 KHz)
FMAP: area COREBOOT found @ 875000 (7909376 bytes)
ASSERTION ERROR: file 'src/commonlib/bsd/cbfs_mcache.c', line 106
BUG=b:177323348
TEST=Boot ezkinil to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I68b4b73670e750207414f0d85ff96f21481be8ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53933
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Building the cbnt-prov tool requires godeps which does not work if
offline. Therefore, add an option to provide this binary via Kconfig.
It's the responsibility of the user to use a compatible binary then.
Change-Id: I06ff4ee01bf58cae45648ddb8a30a30b9a7e027a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
eint event mask register is used to mask eint wakeup source.
All wakeup sources are masked by default. Since most MediaTek SoCs do
not have this design, we can't modify the kernel eint upstream driver to
solve the issue 'Can't wake using power button (cros_ec) or touchpad'.
So we add a driver here to unmask all wakeup sources.
Change-Id: I703d87e3dc49cf4e0b7ff0c75a6ea80245dd73d3
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54007
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UFS reference clock (refclk) is enabled by default, which will cause
the UFSHCI to hold the SPM signal and lead to suspend failure. Since
UFS kernel driver is not built-in, disable refclk in coreboot stage.
Change UFSHCI base register to 0x11270000.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I1386e59f802a9e3c938a7e8dbeea547fbcb02709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Fixes compilation on FreeBSD CURRENT, and possibly other releases.
The compiler, clang, complained about:
util/cbfstool/cbfstool.c:181:40: error: implicit declaration of function 'memmem' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
util/cbfstool/cbfstool.c:181:31: error: incompatible integer to pointer conversion initializing 'struct metadata_hash_anchor *' with an expression of type 'int' [-Werror,-Wint-conversion]
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: I45c02a21709160df44fc8da329f6c4a9bad24478
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53996
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix booting issues on google/kahlee introduced by CB:51723.
Update use inital apic id in smm_stub.S to support xapic mode error.
Check more bits(LAPIC_BASE_MSR BIT10 and BIT11) for x2apic mode.
TEST=Boot to OS and check apicid, debug log for CPUIDs
cpuid_ebx(1), cpuid_ext(0xb, 0), cpuid_edx(0xb) etc
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ia28f60a077182c3753f6ba9fbdd141f951d39b37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
soc_memory_init_params() does not only configure memory init parameters.
Despite its name, it also configures many other things. Therefore, merge
it into its caller function platform_fsp_memory_init_params_cb() to
prevent confusions.
Built clevo/l140cu with BUILD_TIMELESS=1. coreboot.rom remains the same.
Change-Id: Id3b6395ea5d5cb714a412c856d66d4a9bcbd9c12
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52491
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The values were copied from Foxconn D41S, which uses a different codec.
Adjust the codec config as per the settings dumped from vendor firmware.
Change-Id: If6a4c41b5d424adb23ebef402d2d2ad21269fe25
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Some changes:
- bg-prov got renamed to cbnt-prov
- cbfs support was added which means that providing IBB.Base/Size
separatly is not required anymore. Also fspt.bin gets added as an
IBB to secure the root of trust.
Change-Id: I20379e9723fa18e0ebfb0622c050524d4e6d2717
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52971
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This prepares for updating the intel-sec-tools submodule pointer. In
that submodule bg-prov got renamed to cbnt-prov as Intel Bootguard
uses different structures and will require a different tool.
Change-Id: I54a9f458e124d355d50b5edd8694dee39657bc0d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We need to modify update CmdMirror and LpDdrDqDqsRetraining parameters
for ADLRVP board.
Allowing this parameters to be filled by devicetree will allow
flexibility to update values as per board designs.
Note that both UPDs are applicable for both DDR and Lpddr memory types.
BUG=None
BRANCH=None
TEST=Build works and UPD values have been filled correctly
Change-Id: I55b4b4aee46231c8c38e208c357b4376ecf6e9d9
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This reverts commit 6eced03b25.
This prevents zork from booting. We get the following error:
eSPI cmd0-cmd2: 00080009 00000000 00000000 data: 00000000.
Error: unexpected eSPI status register bits set (Status = 0x10000010)
Error: Slave GET_CONFIGURATION failed!
This isn't a pure revert. It is more of a fix that keeps the old
behavior.
BUG=b:187122344
TEST=Boot zork an no longer see eSPI error
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If75a35d3994b0fd23945a450032d3cc81abeb136
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53932
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Cezanne must use cold resets. Change the warm reset request to always
set TOGGLE_ALL_PWR_GOOD. And, since the bit is sticky across power
cycles, set it early for good measure.
BUG=b:184281092
TEST=Majolica successfully resets using 0xcf9
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I7d4ca5665335b20100a5c802d12d79c0d0597ad9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
AMDFW tool stores bios dir entry to bios1_entry in picasso but
bios3_entry in cezanne. Separate getting bios_dir_addr into a function
and implement it on each platforms.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ie18ed7979a04319c074b9b251130d419dc7f22dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52964
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move all platform-specific code except direct svc calls to chipset.c.
There will be differences between each platforms and we can't put
everything into svc.c.
TEST=build firmware for zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ie7a71d1632800072a17c26591e13e09e0269cf75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52963
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To configure and enable the IOAPIC in the graphics and northbridge (GNB)
container, FSP needs to write an undocumented register, so pass the GNB
IOAPIC MMIO base address to make it show up at that address.
BUG=b:187083211
TEST=Boot guybrush and see IO-APIC initialized
IOAPIC[0]: apic_id 16, version 33, address 0xfec00000, GSI 0-23
IOAPIC[1]: apic_id 17, version 33, address 0xfec01000, GSI 24-55
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1e127ce500d052783f0a6e13fb2ad16a8e408b0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52905
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PIC IRQs are required so we can correctly set up the PCI_INT
registers. This only matters when booting in PIC mode. We don't need to
set the IO-APIC registers since the linux kernel will auto-assign those
to reduce conflicts.
BUG=b:184766519
TEST=Boot guybrush with `pci=nomsi,noacpi amd_iommu=off noapic` and
verify xhci and graphics continue to work.
$ cat /proc/interrupts
12: 285064 XT-PIC nvme0q0, nvme0q1, rtw88_pci
13: 100000 XT-PIC xhci-hcd:usb1
14: 4032 XT-PIC amdgpu, xhci-hcd:usb3
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1d66ccd08a86a64242dbc909c57ff9685828f61f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52915
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This uses the new FSP PCI methods to pull the routing table and populate
the pirq data structure.
BUG=b:184766519
TEST=Boot guybrush and verify we get Got IRQ 0x1F (disabled) messages
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ie21229cc2fb4fd5b85c0b9e933f7b43af24864b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This is loosely based off of picasso/pcie_gpp.c. This version uses the
acpigen_write_PRT_X methods to write the actual records. There are also
two functions, 1 for using the GNB, and one for using the FCH. The FCH
one is useful when the GNB IO-APIC has not been initialized.
BUG=b:184766519
TEST=Dump guybrush ACPI and verify it looks correct
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I926430074acb969ceb11fdb60ab56dcf91ac4c76
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This allows us to use the common get_pci_routing_info and
pci_calculate_irq. The IRQ field in the struct was also filled in from
the PPR.
BUG=b:184766519
TEST=Boot ezkinil and verify SSDT table is identical.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I16d90d8c89bfcf48878c0741154290ebc52a4120
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53923
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This struct is similar to `struct pci_routing` defined in
picasso/pcie_gpp.c. It additionally contains the irq used for the bridge
and is structured in a way that the FSP can provide via HOB.
The next set of CLs will migrate the pci routing functions used by
picasso into common and enable pci routing table generation for cezanne.
BUG=b:184766519
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1a8d988d125f407f0aa7bc1722d432446aa9aff8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
These parameter IDs are defined in the AGESA Interface specification
#55483. This patch also adds a ALIB_DPTC_ prefix to the IDs and makes
the names more consistent.
TEST=Timeless build for Mandolin results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I75e0504f6274ad50c53faa8fcbde4d6821d85a04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53917
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The other enum entries are control IDs for the
ALIB_FUNCTION_DYNAMIC_POWER_THERMAL_CONFIG ALIB function while
DPTC_TOTAL_UPDATE_PARAMS is the total number of configuration settings
that will get passed as parameter in the ALIB call, so it shouldn't be
part of that enum.
TEST=Timeless build for Mandolin results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0cb9e9d2ba579a74d916011b4ead71cc86d69a24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53916
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ACPI ALIB function numbers are defined in the AMD Generic
Encapsulated Software Architecture (AGESA™) Interface Specification
(document #55483).
TEST=Timeless build stays the same for Mandolin (Picasso) and Gardenia
(Stoneyridge).
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I290ef0db32c65ebb2bbbe4f65db4df772b884161
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53915
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The mcache is overflowed in the latest build. In order
to fix the mcache overflow, we increase the mcache size
to 0x4000 and adjust the percentage to 50% for the ro/rw
mcache. This change is for all of the volteer variants
as we see many of the volteer variants which use the
latest bios having the mcache overflow issue.
BUG=b:187095474, b:187095765, b:187234881, b:162052593
TEST=no mcache overflow in the bios log
Change-Id: If9552bc9fa5d36b1ca662c9da030ae7b137b60a8
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
The SN65DSI86 eDP bridge supports two ways to read the EDID: for now
we've been using "direct mode", which works by basically making the
bridge I2C device listen to another chip address besides its own and
proxy all requests received there directly to the eDP AUX channel. The
great part about that mode is that it is super easy and hassle-free to
use. The not so great part about it is that it doesn't work: for EDID
extensions, the last byte (which happens to contain the checksum) is
somehow always read as zero. We presume this is a hardware bug in the
bridge part.
The other, much more annoying way is "indirect mode", where each byte
transmitted over the AUX channel has to be manually set up in the I2C
registers of the bridge, just like we're already doing with DPCD
transactions. Thankfully, we can reuse most of the DPCD code for this so
it's not a lot of extra code. It's a bit slower but not as much as you'd
expect (26ms instead of 18ms on my board), and the difference is not
very relevant compared to common total times for display init.
Also, some of the (previously unused) enum definitions for the AUX_CMD
mode field of the bridge had just been plain wrong for some reason, and
needed to be fixed to make this work.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I65f80193380d3c3841f9f5c26897ed672f45e15a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52959
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the volet variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:186334008
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOLET
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ic6ca9a78494e3819b0fb39c0bcc70fed95c2c589
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Bank interleaving does not work on this platform, disable it.
Additionally enable ECC feature on SKUs supporting it. AmdIntPost
returns success thanks to these settings.
TEST=boot apu2 4GB ECC and apu3 2GB no ECC and see AGESA_SUCCESS after
AmdInitPost
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I010645f53b404341895d0545855905e81c89165e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
We need to configure CPU PCIE root port related gpios in early
boot block stage for CPU root ports to work. Since we're removing
this programming from FSP, coreboot needs to take care of programming
this GPIOs. Also we need to enable virtual wire messaging for native
gpios for CPU PCIE root ports.
Change-Id: Ieda6b6c31ce5bd5e84e4efe544bfc659283ce6f1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52270
Reviewed-by: Balaji Manigandan <balaji.manigandan@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On tgl, we noticed system hang if a shutdown is triggered before fsps.
The dut is unable to shutdown properly due to tcss is stuck before
tcss_init in fsps.
This change enable power button smi on jsl, tgl, adl after fsps.
it can also prevent a shutdown failure due to lack of fsps init on
certain ip.
BUG=b:186194102, b:186815114
TEST=Power on the system and pressing power button repeatedly doesn't
cause the system hang during shutdown.
Change-Id: I70b871f2676a89bc782116e02beba5c20ec51eef
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
If a power button SMI is triggered between where it is currently
enabled and before FSP-S exits, when the SMI handler disables
bus mastering for all devices, it inadvertently also disables
the PMC's I/O decoding, so the register write to actually go into
S5 does not succeed, and the system hangs.
This can be solved by skipping the PMC when disabling bus
mastering in the SMI handler, for which a callback,
smihandler_soc_disable_busmaster is provided.
BUG=b:186194102, b:186815114
TEST=Power on the system and pressing power button repeatedly doesn't
cause the system hang during shutdown.
Change-Id: I1cf5cf91ebad4a49df6679e01fc88ff60c81526c
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Mancomb uses DDR4 SODIMMs, but the default cezanne configuration is for
the LPDDR4 version. This changes to use SODIMMS.
Further changes may be needed for platform customization, so I put the
config file in variants/baseboard instead of the root mancomb directory.
BUG=b:187094481
TEST=Build only
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Icc4dc8aec2053cb177765f57e57cac7a099508fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
DISABLE_KEYBOARD_RESET_PIN - This pin goes to a test point and is not
used for the reset.
DRIVERS_UART_ACPI - Add the UART ACPI code
FW_CONFIG - Mancomb uses the firmware config interface
PSP_DISABLE_POSTCODES - The PSP is not yet initializing eSPI correctly
to send post codes to the EC, so disable them for now.
BUG=None
Test=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I39efcc8d1e0fb1e7ac0b0541a49db0ac0ee56481
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change fixes two problems:
1) We had the enum values for .direction and .level swapped. The naming
is very confusing...
2) ESPI_SYS is not a good event to use for EC SCI. It is a level/low
event that is only cleared by reading the eSPI status register 0x9C.
Cezanne has added a new event source that directly exposes the SCI bit.
This is the correct event source to use for EC SCI.
This same patch was added for Guybrush at CB:52673
BUG=b:186045622, b:181139095
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iac86d2ef5bdd21fbb0a0d4e235efe4fe621023b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52948
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using the push-pull alert was causing leakages when in S0i3. This is
because the EC drives ALERT#, so when the AP enters S0i3, the extra
current leaks into the SoC and ends up turning on the power regulators.
By using in-band ALERT#, the EC no longer drives this pin high, thus
fixing the leak. We could also have used an open drain alert, but the
rise time is less than ideal.
BUG=b:187122344, b:186135022
TEST=Measure S0i3 power on guybrush and validate it's no longer high.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6de771aeda8feca062652f0ea9eb57d31cb68562
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Some designs might wish to use an open drain eSPI ALERT#. This change
adds an enum that allows setting the eSPI alert mode.
BUG=b:187122344, b:186135022
TEST=Boot guybrush using all 3 alert modes
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia35fc59a699cf9444b53aad5c9bb71aa27ce9251
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The eSPI spec says that the Alert Mode defaults to in-band on reset.
This change ensures the controller is in sync with the eSPI peripheral.
The configured alert mode is configured in
espi_set_general_configuration.
BUG=b:187122344, b:186135022
TEST=Boot guybrush and make sure we don't get any eSPI errors.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib43e190d08d77ecfcd22ead2bf42e5de2202b555
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52953
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will print the config we are setting on the eSPI peripheral.
e.g.,
Setting general configuration: slave: 0x98a00000 controller: 0xe2000000
eSPI Slave configuration:
CRC checking enabled
Dedicated Alert# used to signal alert event
eSPI quad IO mode selected
Only eSPI single IO mode supported
Alert# pin is open-drain
eSPI 33MHz selected
eSPI up to 20MHz supported
Maximum Wait state: 0
BUG=b:187122344, b:186135022
TEST=Boot guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1a2382d8ab3d3f0d14a139c57470cb895112eca9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52952
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
None of the options accessed within coreboot is a string, and there are
no guarantees that the code works as intended with them. Given that the
current option API only supports integers for now, do not try to access
options whose type is 's' (string).
Change-Id: Ib67b126d972c6d55b77ea5ecfb862b4e9c766fe5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Do not use get_dram_base_mask to calculate system DRAM limits. Shift
operation around values operating on base and mask were causing
overflows and thus incorrect system DRAM limit. Another function
returning base and limit in KiB has been developed to avoid data loss.
Keep DRAM high base and limit in calculations only for Trinity where
the physical CPU address bits is 48. Although it is almost impossible
to have a non-zero value there, the platform would have to support
nearly 256GB of RAM.
TEST=boot PC Engines apu1 2GB, apu2 4GB and apu3 2GB and boot Debian
with Linux 4.14
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I3b5c1df96c308ff50c8de104e213219a98f25e10
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested on qemu/i440fx on X86_64:
- Page tables are found in cbfs (finding a file works)
- returns 0 when a file is not found
- works when there is no cbfs file at the start of the FMAP, e.g. with
the cbfs master header removed.
Change-Id: Ibab657cc40cd5c09c3a73c54950b98ac45a98dbf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52879
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TGL boards using the Type-C subsystem for USB Type-C ports without a
retimer attached may require a DC bias on the aux lines for certain
modes to work. This patch adds native coreboot support for programming
the IOM to handle this DC bias via a simple devicetree
setting. Previously a UPD was required to tell the FSP which GPIOs were
used for the pullup and pulldown biases, but the API for this UPD was
effectively undocumented.
BUG=b:174116646
TEST=Verified on volteer2 that a Type-C flash drive is enumerated
succesfully on all ports. Verified all major power flows (boot, reboot,
powerdown and S0ix/suspend) still work as expected.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I70e36a41e760f4a435511c147cc5744a77dbccc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The CPU can have its own Port IDs when addressing GPIO communities, which
differ from the PCH PCR IDs.
1) Add a field to `struct pad_community` that can hold this value when
known.
2) Add a function to return this value for a given GPIO pad.
Change-Id: I007c01758ae3026fe4dfef07b6a3a269ee3f9e33
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some SoCs may define virtual wire entries for certain GPIOs. This patch
allows SoC code to provide the mappings from GPIO pads to virtual wire
indexes and bits when they are provided. Also a function
`gpio_get_vw_info` is added to return this information.
Change-Id: I87adf0ca06cb5b7969bb2c258d6daebd44bb9748
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52588
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the pirika variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:184157747
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_PIRIKA
Signed-off-by: kirk_wang <kirk_wang@pegatron.corp-partner.google.com>
Change-Id: I57bf33deeadacc88800f9ce1d3d54385ba56c798
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52626
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adding GPIO definition for community 3 which is CPU reserved GPIO used
by CPU side PCIe root ports. We did not have this definition since
FSP used to program this GPIOs. Now, instead of FSP, coreboot programs
CPU PCIe GPIOs for CLKSRC and lanes to put GPIOs in native mode.
Thus adding definition of this virtual GPIOs in this CL.
BUG=None
BRANCH=None
TEST=Check if correct registers are being programmed
Change-Id: I481ea7e3ba948bf6d37b97d08c675a18ee68125d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Earlier we did not have definition for BIT27 for PAD_CFG0 register, we
will use this BIT to enable "virtual wire messaging for native function"
If this bit is enabled, whenever change is detected on the pad, virtual
wire message is generated and sent to destination set by native function.
This bit must be set while enabling CPU PCIe root port programming for
ADL and thus defining a new macro to set native pad function along with
NAF_VWE bit to make GPIO programming easier from coreboot.
BUG=None
BRANCH=None
TEST=Code compilation works fine and if we use this macro to program
GPIO, proper bit is getting set in PAD_CFG register
Change-Id: I732e68b413eb01b8ae1a4927836762c8875b73d2
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52782
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Pen Detect GPIO is exported through GPIO keys driver to the kernel so
that stylus tools is popped on pen eject event. Hence enable the GPIO
keys driver and configure the devicetree.
BUG=b:186011392
TEST=Build and boot to OS in guybrush. Ensure that PRP0001 device is
added to the ACPI SSDT table. Ensure that the Pen Eject events are
detected.
Event: time 1620159356.243180, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: time 1620159356.243180, -------------- SYN_REPORT ------------
Event: time 1620159356.735316, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Ensure that when the device is suspended, it wake on Pen Eject event and
does not wake on Pen Insert event.
Change-Id: I4d2aa29c0f1839c563b40734527a687a5618ba5c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Should use `name` instead of `field->name`, because `field is supposed
to be NULL at this point.
TEST=add new field from bits 29-64 to volteer, ensure sconfig prints an
error instead of segfaulting.
Change-Id: I933330494e0b10e8494a92e93d6beb58fbec0bc1
Found-by: Coverity CID 1452916
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52888
Reviewed-by: Duncan Laurie
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using PAD_WAKE is actually wrong. The wake bits are only supposed to be
set when using the GPIO controller to wake the system. coreboot's
current architecture relies on using GPEs to wake the system.
BUG=b:186011392
TEST=Wake system from S0i3 with EC and see GPE 3 increment.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If7f9d2c13503c01fb9d834c436dac723f2c3b24c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The only use case for FSP-T in coreboot is for 'Intel Bootguard'
support at the moment. Bootguard can do verification FSP-T but there
is no verification on whether the FSP found by walkcbfs_asm is the one
actually verified as an IBB by Bootguard. A fixed pointer needs to be
used.
TESTED on OCP/Deltalake, still boots.
Change-Id: I1ec8b238384684dccf39e5da902d426d3a32b9db
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
From tests this does not lock down SMRAM and it's also not possible to
read back what is written, be it via PCI mmconfig or io ops. The
FSP integration can be assumed to be bogus on this point.
Change-Id: Ia0526774f7b201d2a3c0eefb578bf0a19dae9212
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51532
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some crc16_byte() and crc32_byte() tests had uint8_t instead of uint16_t
or uint32_t. That caused CRC values to be truncated and made tests
incorrect.
Also fix incorrect pre-calculated CRC values and change test buffer name
to more the accurate.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I61ee029a6950a8dfeb54520b634eaf4ed6bac576
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
This patch removes a call to console_init() and debug print message since
the code is not thread safe. This prevents system hangs (soft hangs)
while in SMM if user drops in a new SOC with more cores or another
socket or as a result of bad configuration. Console is already
initialized after the lock has been acquired so this does not affect any
other functionality.
Tested on DeltaLake mainboard with SMM enabled and 52 CPU threads.
Change-Id: I7e8af35d1cde78b327144b6a9da528ae7870e874
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In follow-up patches, we need to set multiple power domains to
power on the display and audio on MT8195.
Move the power domain data under each SoC and make power_on() API
to support multiple settings.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Change-Id: I8c3d19f1e9a4e516d674d68989ad509f37e5b593
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
MT8195 also uses mt6359p so we can reuse most drivers.
The only differences are IO configuaration, clock setting, and PMIC
internal setting related to soc.
Reference datasheet: MT6315 datasheet v1.4.2.pdf, RH-D-2019-0616.
Reference datasheet: MT6359_PMIC_Data_Sheet_V1.5.docx, RH-D-2018-0205.
Change-Id: I73f9c9bf92837f262c15758f16dacf52261dd3a3
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
If device is supported as a wake source, _S0W should be set to D3hot.
This ensures that the device is put into D3hot by the OSPM.
Power resource(PRIC) for the device is listed in both _PR0 and _PR3. Thus, it ensures that the OSPM does not turn off power resource when device is put into D0 and D3hot. Hence, it is capable of waking the system from D3hot state. However, if it is put into D3cold, then the power resource is turned off by the OSPM.
The devices we are currently looking at for touchscreen/touchpad
do not really support auxiliary power and so do not support wake from D3cold.
BUG=b:186070097
TEST=build and check device wake state _S0W set to 3 in ssdt table.
Change-Id: I34e4b2350875530d3337be700276bcc4fb1f810a
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Using PAD_WAKE is actually wrong. The wake bits are only supposed to be
set when using the GPIO controller to wake the system. coreboot's
current architecture relies on using GPEs to wake the system.
BUG=b:186011392
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib956fc299fe21cd7ea0b465cbdc5c8da830a668d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
The usage of `pci_devfn_t` here is misleading, as these intentionally
store the `PCH_DEVFN_*` macros so they can be used across `smm` and
`ramstage` without requiring the device model. Update to `unsigned int`
instead, as `pci_devfn_t` implies the data is an MMCONF-compatible PCI
devfn offset.
Change-Id: Ic8880de984e6eceda4cbe141e118f3a5fdd672a2
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52808
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With the recent switch to SMM module loader v2, the size of the SMM for
module google/volteer increased to above 64K in size, and thus failed to
install the permanent SMM handler. Turns out, the devicetree is all
pulled into the SMM build because of elog, which calls
`pci_dev_is_wake_source`, and is the only user of `struct device` in
SMM. Changing this function to take a pci_devfn_t instead allows the
linker to remove almost the entire devicetree from SMM (only usage left
is when disabling HECI via SMM).
BUG=b:186661594
TEST=Verify loaded program size of `smm.elf` for google/volteer is
almost ~50% smaller.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4c39e5188321c8711d6479b15065e5aaedad8f38
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add a Kconfig option to set the keyboard translation state on exit and
set the default to true. This restores the keyboard to the power-up
defaults for firmware that does not always run libpayload keyboard init
to have consistent state, and provides an option to disable translation
for keyboards that might need it.
Change-Id: I25dfe3f425a5bb57e97476564886672b707aa3bd
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
While building adlrvp board with chromeos.fmd and adding all chromeos
related artifacts, RO region is running out of space. Also, we need
to increase RW region size to accommodate all binaries and artifacts.
Aligning chromeos.fmd with Brya will help in solving this issue, thus
aligning chromeos.fmd with Brya.
BUG=b:184997582
BRANCH=NONE
TEST=Code compiles fine and able to boot adlrvp platform
Change-Id: I644e2e5ba06d2b816d413a7cc9f5f248d8a6fee8
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52732
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Kconfig change which enables the hwp cppc acpi support is to get the
maximum performance of each CPU to check and enable Intel Turbo Boost
Max Technology.
BUG=none
BRANCH=none
TEST=check GCPC and CPC generated in acpi tables for each CPU
Change-Id: I5d93774e8025466f1911cf77459910fe872bfcc8
Signed-off-by: ravindr1 <ravindra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51795
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sooner or later, some board was going to need extra FW_CONFIG bits for
a field that was already in production, so this patch adds support for
adding extra (unused) bits to a field.
The extra are appended via a syntax like:
`field FIELD_NAME START0 END0 | START1 END1 | START2 END2 ...`
and the suffixed bits are all treated as if they are contiguous when
defining option values.
BUG=b:185190978
TEST=Modified volteer fw_config to the following:
field AUDIO 8 10 | 29 29 | 31 31
option NONE 0
option MAX98357_ALC5682I_I2S 1
option MAX98373_ALC5682I_I2S 2
option MAX98373_ALC5682_SNDW 3
option MAX98373_ALC5682I_I2S_UP4 4
option MAX98360_ALC5682I_I2S 5
option RT1011_ALC5682I_I2S 6
option AUDIO_FOO 7
option AUDIO_BAR 8
option AUDIO_QUUX 9
option AUDIO_BLAH1 10
option AUDIO_BLAH2 15
option AUDIO_BLAH3 16
option AUDIO_BLAH4 31
end
which yielded (in static_fw_config.h):
FW_CONFIG_FIELD_AUDIO_MASK 0xa0000700
FW_CONFIG_FIELD_AUDIO_OPTION_NONE_VALUE 0x0
FW_CONFIG_FIELD_AUDIO_OPTION_MAX98357_ALC5682I_I2S_VALUE 0x100
FW_CONFIG_FIELD_AUDIO_OPTION_MAX98373_ALC5682I_I2S_VALUE 0x200
FW_CONFIG_FIELD_AUDIO_OPTION_MAX98373_ALC5682_SNDW_VALUE 0x300
FW_CONFIG_FIELD_AUDIO_OPTION_MAX98373_ALC5682I_I2S_UP4_VALUE 0x400
FW_CONFIG_FIELD_AUDIO_OPTION_MAX98360_ALC5682I_I2S_VALUE 0x500
FW_CONFIG_FIELD_AUDIO_OPTION_RT1011_ALC5682I_I2S_VALUE 0x600
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_FOO_VALUE 0x700
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_BAR_VALUE 0x20000000
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_QUUX_VALUE 0x20000100
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_BLAH1_VALUE 0x20000200
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_BLAH2_VALUE 0x20000700
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_BLAH3_VALUE 0x80000000
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_BLAH4_VALUE 0xa0000700
Change-Id: I5ed76706347ee9642198efc77139abdc3af1b8a6
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52747
Reviewed-by: Duncan Laurie <duncan@iceblink.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This macro contains a cast on the and-mask, which can suppress actual
type overflow issues. Replace it with wrapper functions around the
existing macros in device/mmio.h which still contain a type cast, but
it is a non-issue because the wrapper functions now allow compilers to
check for overflows.
Change-Id: I975bf8152fc961767f0292bff4a03aecd8c65f56
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51886
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that all code has been switched to make use of the new accessors,
the old ones can be dropped. Follow-ups will clean up bitwise accessors.
Change-Id: Ib4cb24ca71f3c3717ea50d147ddca74aaf0288fa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
To keep the "main" haswell.h header short and simple, move PEG register
definitions into a separate file, as done with most other registers.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: Ibfca00456115a4a0c861dd6738605214a7d43fd9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51891
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These accessors were defined as macros in order to allow verifying the
patches that replaced the accessors using BUILD_TIMELESS=1. Now that all
replacement is done, turn the new accessors into static functions to let
the compiler perform overflow checks on the arguments.
Change-Id: Iaa2ba208fba11c4a00f2b8a05eb1129a32c6c092
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52816
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove leading and trailing underscores and change `RAMINIT_H` to be
more consistent with other headers.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: Ie20fcaa0f9393eb0a34054eda53b9bade63cc0d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51890
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop unused chipset type macros, remove unnecessary guards and
reorganize contents so that headers can be included at the top.
Also drop the inclusion from ASL, as it is no longer necessary.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I6fcc0d428d0fdbf410bcbeb6ae4809870b7b498f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51889
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All the boards in the patch have a constraint for the I2C bus to operate
on 100 kHz. Provide dedicated values for rise time, fall time and data
hold time on mainboard level to get a proper timing which takes the bus
load into account. Giving these values the driver computes the needed
timings correctly.
TEST=Measure I2C frequency on all boards while coreboot accesses
external RTC and make sure it is 100 kHz.
Change-Id: Iab634190bda5fa2a4fdf2ebaa1e45ac897d84deb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52721
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Default VBT supports only integrated Display port. Magister supports a
HDMI port and hence support a separate VBT for Magister.
BUG=b:180666608
BRANCH=dedede
TEST=Build and boot to OS.
Cq-Depend: chrome-internal:3661227
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I52c10452887312959f68cfc4e25d5897dae388f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51279
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Provide a SOC_INTEL_SKYLAKE_LGA1151_V2 option to select correct defaults
for the combination of a Union Point PCH with LGA1151v2.
As of the year 2021 it's common for motherboards with Z370, H310C
or B365 PCHs, which are meant to be paired with Coffee Lake CPUs.
Intel provides AmberLakeFspBinPkg to support this combination,
which implements Intel FSP External Architecture Specification v2.1.
Details:
1) Provide SOC_INTEL_SKYLAKE_LGA1151_V2 option that selects
PLATFORM_USES_FSP2_1, SOC_INTEL_COMMON_SKYLAKE_BASE and
SKYLAKE_SOC_PCH_H.
2) Add Amberlake FSP support.
If SOC_INTEL_SKYLAKE_LGA1151_V2 is set, use AbmerLakeFspBinPkg instead
of KabylakeFspBinPkg.
3) Enable Coffee Lake CPUs support.
If SOC_INTEL_SKYLAKE_LGA1151_V2 is set, select
MAINBOARD_SUPPORTS_COFFEELAKE_CPU.
4) Increase stack and heap size in CAR.
If FSP_USES_CB_STACK is set (it's selected by PLATFORM_USES_FSP2_1),
update DCACHE_BSP_STACK_SIZE and FSP_TEMP_RAM_SIZE values.
5) Update maximal number of supported CPUs.
If MAINBOARD_SUPPORTS_COFFEELAKE_CPU is set, set MAX_CPUS to 16.
Signed-off-by: Timofey Komarov <happycorsair@yandex.ru>
Change-Id: I7b6b9c676da55088cb5a12a218ea58d349ee440c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The Z370, H310C and B365 PCHs use the same silicon as 200-series
PCHs and they are supported by soc/intel/skylake codebase
(not by soc/intel/cannonlake). Mentioned PCHs are meant to be paired
with Coffee Lake CPUs, so add the corresponding microcodes.
Signed-off-by: Timofey Komarov <happycorsair@yandex.ru>
Change-Id: I479c648e40c4c607d29f8cdd913fdbd6d7d7d991
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Inspired by discussion in CB:22822.
If I2C bus step response has not been measured, assume the layout to
have been designed with a minimal capacitance and SCL rise and fall
times of 0 ns. The calculations will add the required amount of
reference clocks for the host to drive SCL high or low, such that the
maximum bus frequency specification is met.
Change-Id: Icbafae22c83ffbc16c179fb5412fb4fd6b70813a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52723
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The usage of external oscillator has got nothing to do with Audio
Co-processor (ACP). Hence move it out of common config and put it into
the SoC config where it is being used.
BUG=None
TEST=Build Dalboz and Vilboz mainboards.
Change-Id: I8c5d98addfba750f9ddb87a846599541b4a8340a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
cmocka is currently ignoring the UPDATED_SUBMODULES flag. Move the
cmocka checkout with the other submodule checkouts.
BUG=none
TEST=Make sure cmocka is not checked out if UPDATED_SUBMODULES=1
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I2a1db809368a77d2c0f9c9a796d62555ec476dc7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
The existing helpers for reading/writing MSRs (rdmsr, wrmsr) require use
of the struct `msr_t`, which splits the MSR value into two 32 bit parts.
In many cases, where simple 32 bit or 64 bit values are written, this
bloats the code by unnecessarly having to use that struct.
Thus, introduce the helpers `msr_read` and `msr_write`, which take or
return `uint64_t` values, so the code condenses to a single line or two,
without having to deal with `msr_t`.
Example 1:
~~~
msr_t msr = {
.lo = read32((void *)(uintptr_t)0xfed30880),
.hi = 0,
};
msr.lo |= 1;
wrmsr(0x123, msr);
~~~
becomes
~~~
uint32_t foo = read32((void *)(uintptr_t)0xfed30880);
msr_write(0x123, foo | 1)
~~~
Example 2:
~~~
msr_t msr = rdmsr(0xff);
uint64_t msr_val = (msr.hi << 32) | msr.lo;
~~~
becomes
~~~
uint64_t msr_val = msr_read(0xff);
~~~
Change-Id: I27333a4bdfe3c8cebfe49a16a4f1a066f558c4ce
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52548
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds full EINJ support with trigger action tables. The actual
error injection functionality is HW specific. Therefore, HW specific
code should call acpi_create_einj with an address where action table
resides. The default params of the action table are filled out by the
common code. Control is then returned back to the caller to modify or
override default parameters. If no changes are needed, caller can
simply add the acpi table. At runtime, FW is responsible for filling
out the action table with the proper entries. The action table memory
is shared between FW and OS. This memory should be marked as reserved
in E820 table.
Tested on Deltalake mainboard. Boot to OS, load the EINJ driver (
modprobe EINJ) and verify EINJ memory entries are in /proc/iomem.
Further tested by injecting errors via the APEI file nodes. More
information on error injection can be referenced in the latest ACPI
spec.
Change-Id: I29c6a861c564ec104f2c097f3e49b3e6d38b040e
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Rocky Phagura
guybrush and mancomb don't configure any GPIO as PAD_SMI. Since
mainboard_smi_gpi will only get called for a GEVENT that will cause a
non-SCI SMI, this isn't expected to be called. For the unexpected and
very unlikely case that it still does get called, put a printk into
mainboard_smi_gpi to see what is happening there.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifd6e3348ecc078932bf6cf5b0830b4b034d274bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52360
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
zork doesn't configure any GPIO as PAD_SMI. Since mainboard_smi_gpi will
only get called for a GEVENT that will cause a non-SCI SMI, this isn't
expected to be called. For the unexpected and very unlikely case that it
still does get called, put a printk into mainboard_smi_gpi to see what
is happening there.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I14c67b21a83b334558cdd54ebf700924aa9d0808
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52359
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
From cezanne we have enough space in PSP so we don't have to worry about
workbuf size. Hence the function only exists in picasso and deprecated
for later platforms.
So wrap svc_get_max_workbuf_size and provide default weak function so
future platforms don't have to implement dumb function for it.
TEST=build and boot zork, check weak function is not called in zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I16e8edf8070aaacb3a6a6a8adc92b44a230c3139
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Configure Audio Co-processor(ACP) to operate in I2S TDM mode. Also fix
the scope in which ACP is defined in the devicetree.
BUG=b:182960979
TEST=Build and boot to OS in Guybrush. Ensure that the ACPD device is
enabled in the appropriate scope in SSDT.
Change-Id: Ic90fd82e5c34a9feb9a80c4538a45e7c2fb91add
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Audio Co-processor driver is similar for both Picasso and Cezanne SoCs.
Hence move it to the common location.
BUG=None.
TEST=Builds Dalboz, Trembyle, Vilboz, Mandolin and Bilby mainboards.
Change-Id: I91470ff68d1c183df9a2927d71b03371b535186a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Some platforms which have large amounts of RAM and also write-combining
regions may decide to drop the WC regions in favor of the default when
preserving MTRRs for the OS. From a data safety perspective, this is
safe to do, but if, say, the graphics framebuffer is the region that is
changed from WC to UC/WB, then the performance of writing to the
framebuffer will decrease dramatically.
Modern OSes typically use Page Attribute Tables (PAT) to determine the
cacheability on a page level and usually do not touch the MTRRs. Thus,
it is believed to be safe to stop reserving MTRRs for the OS, in
general; PentiumII is the exception here in that OSes that still
support that may still require MTRRs to be available. In any case, if
the OS wants to reprogram all of the MTRRs, it is of course still free
to do so (after consulting the e820 table).
BUG=b:185452338
TEST=Verify MTRR programming on a brya (where `sa_add_dram_resources`
was faked to think it had 32 GiB of DRAM installed) and variable MTRR
map includes a WC entry for the framebuffer (and all the RAM):
MTRR: default type WB/UC MTRR counts: 13/9.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x00003fff80000000 type 6
MTRR: 1 base 0x0000000077000000 mask 0x00003fffff000000 type 0
MTRR: 2 base 0x0000000078000000 mask 0x00003ffff8000000 type 0
MTRR: 3 base 0x0000000090000000 mask 0x00003ffff0000000 type 1
MTRR: 4 base 0x0000000100000000 mask 0x00003fff00000000 type 6
MTRR: 5 base 0x0000000200000000 mask 0x00003ffe00000000 type 6
MTRR: 6 base 0x0000000400000000 mask 0x00003ffc00000000 type 6
MTRR: 7 base 0x0000000800000000 mask 0x00003fff80000000 type 6
MTRR: 8 base 0x000000087fc00000 mask 0x00003fffffc00000 type 0
ADL has 9 variable-range MTRRs, previously 8 of them were used, and
there was no separate entry for the framebuffer, thus leaving the
default MTRR in place of uncached.
Change-Id: I2ae2851248c95fd516627b101ebcb36ec59c29c3
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
From ANX7625 spec, the delay between powering on power supplies and GPIO
should be larger than 10ms. Since it takes about 4ms for the previous
GPIO EN_PP3300_EDP_DX to be pulled up, increase the delay from 2ms to
14ms.
BUG=b:157716104
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: If73747bdaec5ac069b048920d27e27178bc3cedc
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This change is needed to update the option API to use unsigned integers.
The CMOS option system does not support negative numbers.
The volume field is only 8 bits long. Do not set the volume if it is out
of range. Also, use an out-of-range value as fallback to skip setting
the volume when it cannot be read using the option API, to preserve the
current behavior.
Change-Id: I7af68bb5c1ecd4489ab4b826b9a5e7999c77b1ff
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Rewrite google_chromeec_status_check to use stopwatch instead of a
delay in a while loop. In practice the while loop ends up taking
much longer than one second to timeout. Using stopwatch library will
accurately timeout after one second.
BUG=b:183524609
TEST=Build and run on guybrush
BRANCH=None
Change-Id: I363ff7453bcf81581884f92797629a6f96d42580
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
vboot has been updated to track main branch, however the
.gitmodules defaults to master branch following the
coreboot default. This impacts the rebase of submodule
git submodule update --remote --rebase 3rdparty/vboot/
With this change the rebase to latest commit is successful
Signed-off-by: Balaji Manigandan B <balaji.manigandan@intel.com>
Change-Id: I7713aecdec43a5d5623ef81803ac0fc02ce14070
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52664
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code is already compiled in on all platforms. Use it as it provides
the same functionality. Note that GCAP is no longer R/WO on these
platforms. However, select `AZALIA_LOCK_DOWN_R_WO_GCAP` just in case.
This will be dropped in a follow-up.
Tested on Prodrive Hermes, still detects and initializes both codecs.
Change-Id: I75424559b2b4aca63fb23bf4f8d5074aa1e1bb31
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50795
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We don't have any infrastructure setup to handle SCI SMIs. Instead of
just silently ignoring the SMI, print a warning saying that it is
being ignored.
BUG=none
TEST=Trigger an SCI SMI and see warning printed.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I803e572250925b7d5ffdbb3e8958f9aff1f808df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52674
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change is needed to update the option API to use unsigned integers.
The CMOS option system does not support negative numbers. So, adjust the
call to get_int_option() to use 3 as fallback instead of -1.
Change-Id: I46c5f5c6f47f99379cbafc0d60258b99dc512e9d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Always print the chosen fan mode, not only when get_int_option() returns
the fallback value. Callers of get_int_option() should not try to handle
option-related errors, and simply proceed using the fallback value.
This change is needed to update the option API to use unsigned integers.
The CMOS option system does not support negative numbers.
Change-Id: Ic8adbe557b48a46f785d82fddb16383678705e87
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The code name for these PCHs is Union Point, abbreviated as `UPT`. There
are some 300-series Union Point PCHs (H310C, B365, Z370) which are meant
to be paired with Coffee Lake CPUs instead of Skylake or Kaby Lake CPUs,
and referring to them as `KBP` (Kaby Point, I guess) would be confusing.
Tested with BUILD_TIMELESS=1, HP 280 G2 remains identical.
Change-Id: I1a49115ae7ac37e76ce8d440910fb59926f34fac
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52700
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Timofey Komarov <happycorsair@yandex.ru>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
AMD GPIO driver will not load if IRQ is not set. As a consequence,
it does not clear the interrupt when waking from S0i3.
BUG=178728116
TEST=Perform 2 S0i3 cycles, confirming second cycle does not return
instantly due to first interrupt not being cleared.
Change-Id: I3072263e8e68f939a47ed4125444c60133087824
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This change fixes two problems:
1) We had the enum values for .direction and .level swapped. The naming
is very confusing...
2) ESPI_SYS is not a good event to use for EC SCI. It is a level/low
event that is only cleared by reading the eSPI status register 0x9C.
Cezanne has added a new event source that directly exposes the SCI bit.
This is the correct event source to use for EC SCI.
BUG=b:186045622, b:181139095
TEST=`lpc sci` on EC console and see /proc/interrupts increase by 1
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I764b9ec202376d5124331a320767cbf79371dc07
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Newer Intel SoCs also support _PRT tables, but they route PCI devices to
more than just PIRQs, and statically specify IRQs instead of using link
devices. Extend/refactor intel_acpi_gen_def_acpi_pirq to support this
additional use case.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ica420a3d12fd1d64c8fe6e4b326fd779b3f10868
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
https://tech-docs.system76.com/models/oryp6/README.html
Tested with TianoCore (UefiPayloadPkg).
Working:
- PS/2 keyboard, touchpad
- Both DIMM slots
- M.2 NVMe
- M.2 SATA
- MicroSD card slot
- All USB ports
- Integrated graphics using Intel GOP driver
- Webcam
- Ethernet
- Internal microphone
- Combined headphone + mic 3.5mm jack
- Combined microphone + S/PDIF 3.5mm jack
- Booting to Ubuntu Linux 20.10 and Windows 10
- Flashing with flashrom
Not working:
- S3 suspend/resume: System hangs on wake from S3
- Discrete/Hybrid graphics: Requires a new driver
- Internal speakers: Enabled in separate patch
Not tested:
- Thunderbolt functionality
- S/PDIF output
Change-Id: If017d65ca6cb36fe1f631d4dadd050a1547c93fa
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47768
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIOs are divided into different communities. Each community
consists of one or more GPIO groups. We need to configure the
groups in coreboot so that they are mapped properly.
GPIO communities should be properly configured in GPIO_CFG and
MISCCFG registers. GPP_* defines in gpio_soc_defs.h are configured
in GPIO_CFG register while the PMC_GPP_* in pmc.h.
GPIO communities in coreboot should match with the kernel gpio
communities also. Kernel reads the ASL file from coreboot. This
patch adds the proper community mapping in ASL code to match with
kernel code. In gpio_soc_defs.c file we are indexing the groups
correctly. In gpio.h file we define all the gpio devices as kernel
populates sysfs with separate gpio device for each community. This
patch is created based on Intel EHL PCH Datasheet with Document
number 614109 and Chapter 21.
Also update GPIO COM3 Port ID and 2 GPIO register values
(HOSTSW_OWN_REG_0 & PAD_CFG_BASE) respectively.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ifc609b3d6ab9ea2b807dc0f178ec99f95d2db4cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
To train PCIe devices, the devices need to be enabled and taken out of
reset. This patch does the bare minimum needed to train PCIe. It is
not intended to handle timings, which will be addressed later.
Copy the enables for WLAN into early GPIO Init so that they're
enabled before FSP-M runs and trains the PCIe busses.
Again, this patch is the minimum to let the FSP train the PCIe busses.
BUG=b:182202136
TEST=Boot guybrush from NVME.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I5e3e9fe21f44b832e26b0942759ae2ec96ec6c82
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
The VT-d specification states that device scope for remapping hardware
unit which has DRHD_INCLUDE_PCI_ALL flags must be the last in the list
of hardware unit definition structure. This change fixes the devices
list in the DMAR DRHD structure.
BUG=None
TEST=Built image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I14c34ad66a5ee8c30acabd8fe5a05c22087f9120
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52477
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MT8195 requires writing speical value to mode register to clear
status register. This value is invalid on other platforms. We can
do this safely in the common watchdog driver.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Iba5b41f426fc38719bb343a220e0724bff229c79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Currently, some of the PSP Soft Fuse bits are hardcoded in the Cezanne
and Picasso makefiles.
This makes it impossible for platforms to change them. This change puts
the hardcoded bits in Kconfig, allowing them to be modified by the
platform.
BUG=b:185514903
TEST=Verify that the correct Soft Fuse bits are set.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I190ebf47cb7ae46983733dc6541776bf19a2382f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52422
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 4447996cc5.
It looks like the patch repurposed the `memory_reserved_for_heci_mb`
variable as an indicator if the ME firmware is fine. The change to
setup_heci_uma() made it bail out early, even though the implementation
is obviously prepared to set things up even if the requested UMA
size is 0. This also leaves the code in an inconsistent state: The
second if's condition is always true.
Resolves: https://ticket.coreboot.org/issues/305
Change-Id: Ie5a98be3f660078a85a79b5551e86f90f148974f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52426
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Stefan Ott <coreboot@desire.ch>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MC0_CTL_MASK is no longer available in fam 17h and newer and will result
in a general protection fault when accessed. This register was moved, so
use the one that is correct for this CPU generation.
BUG=b:186038401
TEST=Mandolin no longer crashes in the machine check error handling path
with a general protection fault.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ibb042635d917dfcb2121849e2913aa62eca09dd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Currently, it fails to dump the nvme data by test command.
It reports the following error:
cat: '/sys/bus/i2c/devices/i2c-PRP0001:01/eeprom': Connection timed out
So increase the value from 0x0400 to 0x2000 and double the address width from 0x08 to 0x10 to solve this problem.
BUG=b:177393430
TEST=1. cat /sys/bus/i2c/devices/i2c-PRP0001:01/eeprom > /tmp/ov8856_eeprom.bin
2. hexdump -C /tmp/ov8856_eeprom.bin > ov8856_eeprom_dump.log
3. cat ov8856_eeprom_dump.log
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ia933927981f07e0f7954a4bc6d82f0bdd70181f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52048
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: ShawnX Tu <shawnx.tu@intel.com>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Trying to limit the number of available cores by setting the MAX_CPUS
Kconfig option to a lower value than the SoC's default might result in
cores being enabled in the FSP-S, but not fully initialized in coreboot
which will cause some malfunction. Add a static assert to make sure
that this option isn't changed from the default. To limit the maximum
number of cores, use the downcore_mode and disable_smt devicetree
settings instead.
TEST=Build fails if MAX_CPUS isn't the expected default.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3cfe09f8bb89a2154d37a37398df982828c824f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52611
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Trying to limit the number of available cores by setting the MAX_CPUS
Kconfig option to a lower value than the SoC's default might result in
cores being enabled in the FSP-S, but not fully initialized in coreboot
which will cause some malfunction. Add a static assert to make sure
that this option isn't changed from the default. To limit the maximum
number of cores, use the downcore_mode and disable_smt devicetree
settings instead.
BUG=b:184162768
TEST=Build fails if MAX_CPUS isn't the expected default.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Idd6aa1d99128b17218a8e910c33415218a58578f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52606
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
bl_syscall_public.h is a header file for PSP app, but was used for x86
code to get the definition of PSP_INFO. Move the definition into
psp_transfer.h and do not include bl_syscall_public.h from x86 code.
BUG=none
TEST=build psp_verstage on zork
BRANCH=none
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I0fe011652a47d0ba2939dc31ee3b83f0718a61dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52537
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The next guybrush build uses 2 new LPDDR4X memory chips:
- Micro MT53E1G32D2NP-046 WT:B
- Hynix H9HCNNNBKMMLXR-NEE
The MT53E2G32D4NQ-046 WT:A chip has been added to the global LPDDR4X
list since the last time guybrush was updated, so that's brought into
the guybrush SPD directory as lp4x-spd-10.hex, but it's not used.
BUG=b:186027256
TEST=Build only
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ia5efd548f8b9442fb3703518387175aba8933a33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The revision B version of the MT53E1G32D2NP-046 memory chip will be used
in the next guybrush build. It has a different internal layout than the
Revision A part, with 2 ZQ lines per module instead of 1.
BUG=b:186027256
TEST=Build only
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I066f40eb890648a9be17cfe0cee20d299000c11a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Remove the unneeded pull up, as leaving them unterminated disconnects
them from internal logic.
Also replace use of PAD_CFG_TERM_GPO with PAD_CFG_GPO where no
termination is used.
Change-Id: Ia85ea39d46d7d9584b94726a7d601ca06826b1d1
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Coverity detects the control flow UNREACHABLE issue for the printk
usage. This change adds rc to keep the smm_module_setup_stub function
call and returns rc after printk usage.
Found-by: Coverity CID 1452602
TEST=None
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ie3b90a8197c3b84c5a1dbca8a9ef566bef35c9ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52574
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The VT-d specification states that device scope for remapping hardware
unit which has DRHD_INCLUDE_PCI_ALL flags must be the last in the list
of hardware unit definition structure. This change fixes the devices
list in the DMAR DRHD structure.
Change-Id: Ia5fedb6148409f9c72848c9e227e19bedebb5823
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Remove the unneeded pull up, as leaving them unterminated disconnects
them from internal logic.
Also replace use of PAD_CFG_TERM_GPO with PAD_CFG_GPO, as none configure
termination.
Change-Id: I28549a89a885598ba2d5111a9974356562a03cde
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
FSP does not set the MSR LT_LOCK_MEMORY when SkipMpInit=1. Therefore,
set LT_LOCK_MEMORY at end of POST, when native MP init is used, to
protect SMM in accordance to Intel BWG.
Test on clevo/cml-u: chipsec says LT_LOCK_MEMORY is locked.
Change-Id: Iaadd4996653c4f27d268b1c4773c1e2e86114912
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36356
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP uses PchHdaAudioLink{Hda|Dmic|Ssp|Sndw}Enable UPDs to configure
GPIO pads for audio. However, mainboard is expected to perform all
GPIO configration in coreboot and hence these UPDs must be set to
0. There is no need to expose these UPDs in chip.h and provide
mainboard an option to set these in devicetree.
This change drops PchHdaAudioLink{Hda|Dmic|Ssp|Sndw}Enable UPDs from
chip.h and the corresponding devicetree in mainboards. Currently,
shadowmountain already set these UPDs to 0, whereas adlrvp set these
to 1. But all the ADL boards are correctly configuring the GPIO pads
for audio, so this change should not impact audio for any of these
boards.
BUG=b:183482000
TEST=adlrvp and shadowmountain build successfully.
Change-Id: I90e4eb5cc242a789800f4c9f8c71e9d8c8a2becf
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52559
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add PSP_DISABLE_POSTCODES and PSP_POSTCODES_ON_ESPI kconfig options for
cezanne. Select PSP_DISABLE_DISABLE_POSTCODES and unselect
PSP_POSTCODES_ON_ESPI for guybrush. Port80 codes from PSP can cause bus
errors on guybrush.
BUG=b:185514903, b:184356693
TEST=Boot guybrush, observe no port80 codes from PSP
Change-Id: I7241e47ec1b89782e699135370c796eb251afcaa
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52401
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id 9d4053df:
2020-11-20 01:51:08 +0000 - (Revert "Reland: Clean up implicit fall through.")
to commit id 57c0c5be:
2021-04-09 11:45:39 +0800 - (cgpt: Move all GPT on SPI-NOR infra behind a flag)
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Id50a892f12ff3c4147c422c98b640ac047143128
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52453
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The slot ID can be passed in from the function caller but
parsing slot ID from devicetree is not yet supported and
would still be 0.
Add Slot ID in SMBIOS type 9 for Delta Lake.
Tested=Execute "dmidecode -t 9" to verify.
Signed-off-by: JingleHsuWiwynn <jingle_hsu@wiwynn.com>
Change-Id: I9bf2e3b1232637a25ee595d08f8fbbc2283fcd5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change adds the ATC_REQUIRED flag for the address translation cache
indicator and fixes the devices scope entry in the SATC reporting
structure. The SoC integrated devices in the specified PCI segment
with address translation caches are a type of PCI Endpoint Device.
BUG=None
TEST=Built image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I57b3551f11502da48f3951da59d9426df5a40723
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Nico Huber <nico.h@gmx.de>
When using references to a FieldUnit, DeRefOf is not used when storing a
value into the referenced FieldUnit, only when reading its value.
Tested on out-of-tree Compal LA-A992P, Linux 5.11.15-arch1-2 no longer
spews errors like these in dmesg:
ACPI Error: Needed type [Reference], found [Integer] 000000006cbcc5d8 (20201113/exresop-66)
ACPI Error: AE_AML_OPERAND_TYPE, While resolving operands for [And] (20201113/dswexec-431)
ACPI Error: Aborting method \_SB.PCI0.LPD0 due to previous error (AE_AML_OPERAND_TYPE) (20201113/psparse-529)
ACPI Error: Aborting method \_SB.PCI0.I2C0._PS0 due to previous error (AE_AML_OPERAND_TYPE) (20201113/psparse-529)
Change-Id: I60c40452f8b5bdbec76264b578957396de8676ea
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52519
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Replace CONFIG(CHROMEOS) with CONFIG(CHROMEOS_NVS) for cases where
the conditional and dependency are clearly about the presence of
an ACPI NVS table specified by vendorcode. For couple locations also
CONFIG(HAVE_ACPI_TABLES) changes to CONFIG(CHROMEOS_NVS).
This also helps find some of the CONFIG(CHROMEOS) cases that might
be more FMAP and VPD related and not about ChromeOS per-se, as
suggested by followup works.
Change-Id: Ife888ae43093949bb2d3e397565033037396f434
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50611
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CONFIG_MAX_PCIE_CLOCKS renamed to MAX_PCIE_CLOCK_SRC to make it clear that this config
is for the number of PCIe Clock sources available which is different from PCIe clock reqs.
This is more relevant in alderlake, as the number clock source and clock reqs differ.
However since this is a better name, renaming it throughout the soc/intel tree.
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: I747c94331b68c4ec0b6b5a04149856a4bb384829
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52194
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 2c26108208 moved this function to
pmutil.c for Tiger Lake. Do this to all other platforms for consistency.
For Skylake, __SIMPLE_DEVICE__ preprocessor guards are no longer needed.
With this change, pmc.c is only needed in ramstage. Adjust Makefile.inc
accordingly, and drop ENV_RAMSTAGE guards from Skylake.
Change-Id: I424eb359c898f155659d085b888410b6bb58b9ed
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
The VT-d specification states that device scope for remapping hardware
unit which has DRHD_INCLUDE_PCI_ALL flags must be the last in the list
of hardware unit definition structure. This change fixes the devices
list in the DMAR DRHD structure.
BUG=b:185631878
TEST=Built image and booted to kernel on Voxel board.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I408fac7ff1185f4aa87bc4ffac7f25e31a4802b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
- remove unused Kconfig options
- change ACPI device name and HID
- remove ACPI for unused color keyboard backlight
- add support for RGB notification LED
- rename Wifi LED ACPI variable
- set some battery info defaults not populated by the EC
Change-Id: I72eca9deb83e5a6d919d6fcbd3b354fbf6e7a925
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The {get,set}_option() functions are not type-safe: they take a pointer
to void, without an associated length/size. Moreover, cmos_get_option()
does not always fully initialise the destination value (it has no means
to know how large it is), which can cause issues if the caller does not
initialise the value beforehand.
The idea behind this patch series is to replace the current type-unsafe
API with a type-safe equivalent, and ultimately decouple the option API
from CMOS. This would allow using different storage mechanisms with the
same option system, maximising flexibility.
Most, if not all users of get_option() have a value to fall back to, in
case the option could not be read. Thus, get_int_option() takes a value
to fall back to, which avoids repeating the same logic on call-sites.
These new functions will be put to use in subsequent commits.
Change-Id: I6bbc51135216f34518cfd05c3dc90fb68404c1cc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The name of the and_mask parameter was a bit misleading, due to the
function inverting the value. Renaming this into clear and set makes it
more obvious what those parameters will actually do.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If307ab4858541861e22f8ff24ed178d47ba70fe5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52524
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We had the addrspace_32bit rdev in prog_loaders.c for a while to help
represent memory ranges as an rdev, and we've found it useful for a
couple of things that have nothing to do with program loading. This
patch moves the concept straight into commonlib/region.c so it is no
longer anchored in such a weird place, and easier to use in unit tests.
Also expand the concept to the whole address space (there's no real need
to restrict it to 32 bits in 64-bit environments) and introduce an
rdev_chain_mem() helper function to make it a bit easier to use. Replace
some direct uses of struct mem_region_device with this new API where it
seems to make sense.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie4c763b77f77d227768556a9528681d771a08dca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There was a bug in the UPDs for STAPM settings that required one UPD
field to be extended from 8 to 32 bits, so this patch is a breaking
change to the binary layout, but since the UPD struct fields for the SMU
SoC power and performance tuning parameters aren't populated by the
coreboot code yet and we added some padding after each logical section
in the UPD, this isn't expected to cause too much trouble; the only
thing that is required is that a very recent build of the FSP binaries
need to be used in combination with the new coreboot code that will
populate the struct fields in follow-up patches.
BUG=b:182297189
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If39aaf64e8e1b4c0426f22ce8ed07707c2a31e61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The uPEP device is required to support S0i3. The device has been written
in ASL to make it easier to read and maintain. The device constraints
are purely informational. We use a dummy constraint like the Intel
platforms to keep both linux and Windows functional.
In order for this device to be used by the linux kernel the
ACPI_FADT_LOW_PWR_IDLE_S0 flag must be set. So including it
unconditionally doesn't cause any problems.
The AMD Modern Standby BIOS Implementation Guide defines two UUIDs,
one for getting the device constraints, and one for handling
notifications. This differs from the Intel specification and the linux
driver implementation. For this reason I haven't implemented any of the
notification callbacks yet.
BUG=b:178728116
TEST=Boot OS and verify _DSM is called:
[ 0.226701] lps0_device_attach: ACPI: \_SB_.PEP_: _DSM function mask: 0x3
[ 0.226722] lpi_device_get_constraints_amd: ACPI: \_SB_.PEP_: _DSM function 1 eval successful
[ 0.226723] lpi_device_get_constraints_amd: ACPI: \_SB_.PEP_: LPI: constraints list begin:
[ 0.226724] lpi_device_get_constraints_amd: ACPI: \_SB_.PEP_: LPI: constraints list end
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I2deef47eabe702efe1a0f3747c9f27bcec37464b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52445
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On Intel 6-series PCHs, the GCAP register is R/WO (Read / Write Once),
and needs to be written to after the HD Audio controller is taken out
of reset. Add a Kconfig option to read and write back GCAP in order to
lock it down. Follow-up commits will select this option when switching
platforms to use common Azalia code, to preserve original behaviour.
Change-Id: I70bab20816fb6c0bf7bff35c3d2f5828cd96172d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
To make the L140CU able to be selected by other OEMs, use
BOARD_CLEVO_L140CU_BASE for OEM independent options.
BOARD_CLEVO_L140CU represents the standard Clevo mainboard without any
OEM modifications, while BOARD_CLEVO_L140CU_BASE is used for the
baseboard.
Change-Id: Iee82eadebfc851619dbb64de09283c5ee55a499f
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52241
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The macro definitions depend on __SIMPLE_DEVICE__ and are only used in
the get_gpio_base() or lpc_get_pmbase() functions, which already guard
PCH_LPC_DEV usage using __SIMPLE_DEVICE__ in preprocessor.
Change-Id: I5d3681debe29471dfa143ba100eb9060f6364c93
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Hook up FSP-M configuration on mainboard level instead of variant level
being able to do common configuration there.
Also, hook up variant romstage.c on mainboard level for variant
specific configurations.
Change-Id: Ic161f83cb629b1e70ca670e10975a25bc0949656
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Use the same stack location during relocation as for the permanent
handler.
When the number of CPUs is too large the stacks during relocation
don't fit inside the default SMRAM segment at 0x30000. Currently the
code would just let the CPU stack base grow downwards outside of the
default SMM segment which would corrupt lower memory if S3 is
implemented.
Also update the comment on smm_module_setup_stub().
Change-Id: I6a0a890e8b1c2408301564c22772032cfee4d296
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This reverts commit ad7c33abd2. With EFS2
already enabled in EC, enabling early EC sync is not required. Also a
workaround has been added in payload to address any boot issues.
BUG=b:185277224
TEST=Build and boot to OS in Guybrush in both normal and recovery mode.
Cq-Depend: chromium:2832032
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I34f8433739754365c8e5a10fdf7e58e3d1e7e797
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52419
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 1e36dc078e. With EFS2
already enabled in EC, enabling early EC sync is not required. Also a
workaround has been added in payload to address any boot issues.
BUG=b:185277224
TEST=Build and boot to OS in Guybrush in both normal and recovery mode.
Cq-Depend: chromium:2832032
Change-Id: I921dc5c814e5187dce283eeff43075b59885723a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52418
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If we select scancode set #1 and keep that, it can confuse Linux
with keyboards that don't return to set #2 when asked to load the
defaults. This happens for instance with various integrated Think-
Pad keyboards but was also seen with an external PS/2 one.
The chosen configuration, scancode set #2 without translation, seems
to be the default for many systems. So we can expect other payloads
and kernels to work with it.
Change-Id: I28d74590e9f04d32bb2bbd461b67f15014f927ec
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47594
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of ignoring keyboards indefinitely when they failed to
initialize, we wait 5s and then start over with the hotplug
detection. As we always assume a present keyboard at first,
we'd otherwise never have a chance to hot plug a device after
the initial 30s timer ran out.
Change-Id: I8dec4921b2e932442d52b5118cdcf27090633498
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
While we assume a keyboard is attached, we send an echo command every
500ms. If there is no data coming from the keyboard within 200ms, we
assume it was detached.
Correspondingly, if we assume no keyboard is attached, we run an echo
command once per second.
Change-Id: I2c75182761729bf30711305f3d8b9d43eafad675
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47593
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
EN_SPKR is routed to SD pin in the ALC1019 speaker amplifier. The
concerned pin has a voltage rating of 1.8V whereas the EN_SPKR GPIO has
a voltage rating of 3.3 V. The schematics has been updated to bridge the
gap. So enable the speaker amplifier by default and add a gpio override
table to disable the speakers before board version 2.
Also update the codec ACPI HID name for the kernel machine driver to
probe the codec successfully.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the GPIO output state
is high.
Change-Id: I32b29bfae9bc94b5119b33a535d8bc825ef89445
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52355
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable AMD I2S machine driver and configure the devicetree with HID
information so that the machine driver ACPI objects can be passed to the
kernel.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the ACPI objects for
machine driver is populated.
Change-Id: I8ed474d25273082d1e0742ba93746d97930deb19
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The selector component in Sound Open Firmware (SOF) can consume all the
mics and use the configuration in the Use Case Manager (UCM) to select
the right channel. Hence dmic select gpio configuration is optional.
BUG=b:182960979
TEST=Build and boot to OS in Guybrush. Ensure that the machine driver
ACPI object is populated without DMIC select GPIO.
Change-Id: Iba00b07c3656c487e33bab184fefee7037745e2d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52393
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:31250 ("soc/intel/cannonlake: Configure GPIOs again after FSP-S is
done") introduced a workaround in coreboot for `soc/intel/cannonlake`
platforms to save and restore GPIO configuration performed by
mainboard across call to FSP Silicon Init (FSP-S). This workaround was
required because FSP-S was configuring GPIOs differently than
mainboard resulting in boot and runtime issues because of
misconfigured GPIOs.
This issue has since been fixed in FSP (verified with FSP v1263 on
hatch). However, there were still 4 boards in coreboot using
`cnl_configure_pads()`. As part of RFC CB:50829, librem_cnl, clevo/cml-u
and system76/lemp9 were tested to ensure that this workaround is no
longer required.
This change drops the workaround using `cnl_configure_pads()` and
updates all mainboards to use `gpio_configure_pads()` instead.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Angel Pons <th3fanbus@gmail.com>
(Tested purism/librem_cnl)
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
(Tested clevo/cml-u which is similar to system76/lemp9)
Change-Id: I7a4facbf23fc81707cb111859600e641fde34fc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52248
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update GPIO config based on review of latest schematics:
- LAN/WLAN reset lines are NC
- SDIO lines configured via GPP_G0-G7
- DMIC lines are wired directly to codec, not PCH, so GPP_D17-20
are set to NC
- Pads GPP_H0-H3 are configured for I2S2
- Pads GPP_H7-H9 are straps for board revision, so treated as GPI
- CPU_C10_GATE# is NC
- PWRBTN# does not need an internal pull-up
- GPP_C20-23 are configured for M.2 UART
- SATAXPCIE1/2 and EC SCI/SMI lines do not need internal pull ups
- GPP_C6/C7 set to I2C1 for future use
- GPP_E15 changed from SCI to SMI, edge triggered
Change-Id: If113cfeadf093e10dd84ab827ead594088f02ba1
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52389
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The default of 32 buses per hotplug bridge is rather high. Especially
for platforms that limit MMConf space to 64 buses: they run out of
numbers if there is more than a single hotplug bridge.
Lower the default to
* 8 if MMConf is limited to 64 or less buses,
* 16 if MMConf is limited to 128 or less buses.
Change-Id: I06d522dd92ceea9f4798273b26f947a5333800c3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52069
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I wished there was a way to do this in smaller steps, but with
every line fixed an error somewhere else became visible. Here
is a (probably incomplete) list of the issues:
* Only one set of parentheses was supported. This is a hard
to solve problem without a real parser (one solution is to
use an recursive RE, see below).
* The precedence order was wrong. Might have been adapted just
to give a positive result for the arbitrary state of the tree.
* Numbered match variables (e.g. $1, $2, etc.) are not local.
Calling handle_expressions() recursively once with $1, then
with $2, resulted in using the final $2 after the first
recursive call (garbage, practically).
Also, symbol and expression parsing was mixed, making things
harder to follow.
To remedy the issues:
* Split handle_symbol() out. It is called with whitespace
stripped, to keep the uglier REs in handle_expressions().
* Match balanced parentheses and quotes when splitting
expressions. In this recursive RE
/(\((?:[^\(\)]++|(?-1))*\))/
the `(?-1)` references the outer-most group, thus the whole
expression itself. So it matches a pair of parentheses with
a mix of non-parentheses and the recursive rule itself inside.
This allows us to:
* Order the expression matches according to their precedence
rules. Now we can match `<expr> '||' <expr>` first as we should
and everything else falls into its place.
* Remove the bail-out that silenced the undefined behavior.
Change-Id: Ibc1be79adc07792f0721f0dc08b50422b6da88a9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Since there are some differences between picasso PSP svc and cezanne PSP
svc, each platform should have their own svc wrapper.
Moreover cezanne PSP will drop unused parameters from
update_psp_bios_dir and save_uapp_data so make wrapper around it.
BUG=b:182477057
BRANCH=none
TEST=build psp_verstage and boot on zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I69f998865fc3184ea8900a431924a315c5ee9133
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52307
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
psp_verstage is not specific to picasso. There might be picasso-specific
code but move everything into common as a first step. While developing
psp_verstage for cezanne picasso-specific code will move back to picasso
directory.
BUG=b:182477057
BRANCH=none
TEST=build psp_verstage on zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ifb1df0d82b972f28be2ffebd476c2553cbda9810
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This change implements `gpio_snapshot()` and `gpio_verify_snapshot()`
callbacks that are useful for debugging any GPIO configuration changes
across FSP-S. These can be utilized by all Intel SoCs that make use of
the common block GPIO driver.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I82a1f125c490b9d6e26e6e9527c2fcd55bb9d429
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Traditionally, for each Intel platform using FSP, FSP-S has at some
point configured GPIOs differently than the mainboard configuration in
coreboot. This has resulted in various side-effects in coreboot,
payload and OS because of misconfigured GPIOs. On more recent Intel
platforms, a UPD `GpioOverride` is added that coreboot can use to
ensure that FSP does not touch any GPIO configuration.
This change adds a debug option `CHECK_GPIO_CONFIG_CHANGES` to fsp2_0
driver in coreboot that makes a platform callback `gpio_snapshot` to
snapshot GPIO configuration before making a call to FSP SiliconInit
and Notify phases. This snapshot is then compared against the GPIO
configuration using platform callback `gpio_verify_snapshot` after
returning from FSP. The callbacks are not added to romstage (FSP-M)
because mainboard configures all pads in ramstage.
This debug hook allows developers to dump information about any pads
that have a different configuration after call to FSP in ramstage. It
is useful to identify missed UPD configurations or bugs in FSP that
might not honor the UPDs set by coreboot.
This debug hook expects the platform to implement the callbacks
`gpio_snapshot` and `gpio_verify_snapshot`. These can be implemented
as part of the common GPIO driver for platforms using
FSP2.0+. Platforms that implement this support must select the config
`HAVE_GPIO_SNAPSHOT_VERIFY_SUPPORT` to make the debug config
`CHECK_GPIO_CONFIG_CHANGES` visible to user.
Proposal for the GPIO snapshot/verify support was discussed in the RFC
CB:50829.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I5326fc98b6eba0f8ba946842253b288c0d42c523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50989
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both touchpads supported by zork use level-triggered wakeup signal.
BRANCH=zork
BUG=b:172846122,b:182911201
TEST=1. cros build-ap -b zork
2. both Synaptics and ELAN touchpads work fine on Vilboz
3. Wakeup source is correctly reported on Vilboz
Signed-off-by: Victor Ding <victording@google.com>
Change-Id: Icc2b5ad3bd434c9759a0fdfc121aa3c94f46630e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52367
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the datasheet provided by ELAN, the /INT pin is "low active"
and "indicates touchpad likes to send data to system(host) when low".
The signal is level-triggered.
BRANCH=zork
BUG=b:172846122
TEST=cros build-ap -b zork
Signed-off-by: Victor Ding <victording@google.com>
Change-Id: I1f2182aaf483932304591ab14592f35214ea6efd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52366
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The headers added are generated as per FSP v2117_00.
Previous FSP version was v2081_02.
Changes Include:
- Adjust Reserved UPD Offset in FspmUpd.h and FspsUpd.h
- Remove FivrFaults and FivrEfficiency Upds from FspmUpd.h
- Few UPDs description update in FspmUpd.h and FspsUpd.h
BUG=b:184129128
BRANCH=None
TEST=Build and boot ADLRVP
Change-Id: I068552084b1ef3e5c4fba7a46240d116c92c7b5b
Cq-Depend: TBD
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
TPM_INIT_RAMSTAGE needs to be enabled for measured boot only
configuration.
Remove TPM_INIT_RAMSTAGE disable.
BUG = NA
TEST = Boot possible combinations of VBOOT, measured boot and vendorcode
security.
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Change-Id: I91bde691d445d4210429c928e90e16653092f1cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Three stages of the new tint build system:
1) generate_core.sh extracts the core part from buildgcc script,
most importantly the checksum calculation/verification functions.
2) tintify_core.sh adds the tint-specific footer/header to the core,
such as the properties of current version including its checksum.
3) tint.sh - generated and "tintified" core script - builds a tint.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: Ib71f5b861ecf91949a5af12812258e60873f0498
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We need to change OC pin for type C USB3 ports and it depends
on the board design. Allowing it to be filled by devicetree will
make it easier to change the mapping based on the board design
BUG=b:184653645
BRANCH=None
TEST=compilation works fine and value of UPD is getting reflected.
Change-Id: I61faa661c12dced27c6cdd7005a61ae8de8621e1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
When MRC cache region type is not found (for example, in recovery mode
with !HAS_RECOVERY_MRC_CACHE), mrc_cache_stash_data() will return 0.
Therefore, the platform code is not able to tell from the return value
if the MRC cache data is actually written to flash or not. Since the MRC
driver is already pretty verbose, ignore the return value and remove the
misleading memory logs.
BUG=none
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: I6b411664ca91b9be2d4518a09e9734d26db02d6e
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52361
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is no need to stash the SCI trigger register configuration and
apply it at the end. Remove this to make SCI and SMI programming more
symmetrical and to use available configure_scimap function instead of
implementing it again, but without the additional checks. Using this
function also allows removing soc_route_sci.
Change-Id: Ie23da79546858282910db65182a6315ade506279
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This adds a driver for the TI TAS5825M smart amplifier [1].
The driver expects the mainboard using it to define tas5825m_setup(),
which uses the tas5825m_* functions to set configuration data. Each
mainboard may have very different configuration data, depending on
its audio hardware.
Tested on System76 addw1, bonw14, oryp5, and oryp6.
[1]: https://www.ti.com/product/TAS5825M
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Change-Id: I896e8f272f18e64bfc90f406e7d4163010800aaf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The new discovery from Google & AMD, the value currently used
STAPM Time Constant of 1640 is reducing real PPT TSP from the
target 4.8W to 4.68W.
Furthermore, when using the "default" STAPM Time Constant of 1400,
the actual real PPT TSP becomes 4.89W.
Operating at this default settings therefore uses a higher real PPT TSP,
which results in a significant performance improvement.
BUG=b:175364713,b:184902568
BRANCH=zork
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I9cf4d51f42fe250340bcb642db07796c9a480c34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52312
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The new discovery from Google & AMD, the value currently used
STAPM Time Constant of 1640 is reducing real PPT TSP from the
target 4.8W to 4.68W.
Furthermore, when using the "default" STAPM Time Constant of 1400,
the actual real PPT TSP becomes 4.89W.
Operating at this default settings therefore uses a higher real PPT TSP,
which results in a significant performance improvement.
BUG=b:184902568
BRANCH=zork
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I102c1c5f8215a6c5f7a4451f5731167c32e27c90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52313
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add wifi sar for botenflex.
Due to fw-config cannot distinguish between boten and botenflex.
Using sku_id to decide to load botenflex custom wifi sar.
Detail reason for using sku_id in b:182433707.
BUG=b:182433707
TEST=build and test on boten/botenflex
Cq-Depend: chrome-internal:3686313
Change-Id: Id3f2529a7ad56ff306df98f77cda556656da52a5
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested with TianoCore payload (UefiPayloadPkg).
Working:
- PS/2 keyboard, touchpad
- Both DIMM slots
- NVMe port
- SATA port
- SD card slot
- Left USB 3 Type-A port
- Right USB 3 Type-A port
- Right USB 3 Type-C port
- Webcam
- Ethernet
- Integrated graphics using Intel GOP driver
- mDP output
- HDMI output
- Internal microphone
- Internal speakers
- 3.5mm audio input
- 3.5mm audio output
- S3 suspend/resume
- Flashing with flashrom
- Booting to Ubuntu Linux 20.10 and Windows 10
Not tested:
- Thunderbolt functionality
Change-Id: I5c992e603dbd57ae1b4ddc3a0f9bfc92d6acc813
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The functionality to restore the previous power state after power was
lost that could previously be enabled by selecting
MAINBOARD_POWER_RESTORE in the mainboard's Kconfig can now be achieved
by selecting POWER_STATE_PREVIOUS_AFTER_FAILURE in the mainboard's
Kconfig instead.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I49c4a44ca2c4fa937a823c4eddf1618739c15114
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The functionality to restore the previous power state after power was
lost that could previously be enabled by selecting
MAINBOARD_POWER_RESTORE in the mainboard's Kconfig can now be achieved
by selecting POWER_STATE_PREVIOUS_AFTER_FAILURE in the mainboard's
Kconfig instead.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iab9578ebea89651dc2389bf6ca93ca3f3507eb47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Picasso and Stoneyridge didn't do a read-modify-write operation on the
lower nibble of PM_RTC_SHADOW_REG, but just wrote the upper nibble as
all zeros. Since the upper nibble might be uninitialized before the
lower nibble gets written, do what Picasso and Stoneyridge did here
instead of what the reference code does. Also add a comment why and how
this register behaves a bit weird.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0bda2349e3ae84cba50b187cc773fd8a5b17f4e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Not selecting POWER_STATE_DEFAULT_ON_AFTER_FAILURE brings Cezanne that
is currently the only SoC using this functionality in line with Picasso
where the default is that the board remains in power off mode after
power was lost and later restored. Boards can change this behavior by
selecting POWER_STATE_OFF_AFTER_FAILURE, POWER_STATE_ON_AFTER_FAILURE or
POWER_STATE_PREVIOUS_AFTER_FAILURE.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic96f40e3c9867cd821e58d752f58b763930f6d0f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The first CSE Lite SKU is available, therefore enable the Kconfig
option to have the CSE reboot the system into its RW FW during a cold
boot.
BUG=b:183826781
TEST=50 cold reboot cycles
Cq-Depend: chrome-internal:3758108
Change-Id: Ib3a1a9f8ac51bdab8858b2764d5bc0f6f07987cc
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Gerrit is able to add reviewers based on entries in the `MAINTAINERS`
file. For inclusion and exclusion matches either paths or regular
expressions can be used. The syntax is described in the header of the
file.
When matching a path, there are two sensible possibilities:
- `path/to/file` matches a file.
- `path/to/dir/` matches a folder including its contents recursively.
- `path/to/dir/*` matches all files in that folder, without recursing
into its subfolders.
The trailing slash in the second example is essential. Without it, only
the directory entry itself matches when, for example, the folder gets
deleted, renamed or its permissions get modified. Reviewers in the list
won't get added to changes of any files or directories below that path.
However, from time to time entries get added without this trailing
slash. Thus, implement a workaround in `maintainers.go` to check, if a
path entry is actually a directory. In such case a trailing slash gets
appended, so that the contents will match, too.
Example: `path/to/dir` will become `path/to/dir/`
Tests:
1. output before and after does not differ
2. manual test of resulting regex when running `maintainers.go`
Change-Id: Ic712aacb0c5c50380fa9beeccf5161501f1cd8ea
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52276
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
maintainers.go does not handle globs as described in MAINTAINERS.
Instead of only matching the files inside a directory, it also matches
everything below. Also, a glob used in between (`e.g. path/to/*/dir`)
could lead to matching many more paths unexpectedly.
This is caused by the way paths using globs are converted to regegular
expressions for use with gerrit:
1. The script converts all paths with trailing slash to a path with
trailing glob. That means, a recursive match on a directory gets
converted to match only the files in the directory (at least
according to the documentation - if there wasn't 2).
Example: `path/to/dir/` becomes `path/to/dir/*`
2. When converting the path to a regex, all globs get converted to
prefix matching by replacing the glob by `.*`. Instead of only
matching the files in the directory, everything below matches,
which is a) not what the documentation states and b) the opposite
of what 1. did first.
Example: `path/to/dir/*` becomes `^path/to/dir/.*$`
In sum, this leads to all sorts of issues. Examples:
- `path/*/dir` becomes `^path/.*/dir$`
- `path/to/dir/*` becomes `^path/to/dir/.*$`
- `path/to/*.c` becomes `^path/to/.*\.c$`
This change fixes that behaviour by:
- dropping the wrong conversion from 1. above.
- fixing glob matching by replacing `*` by `[^/]`.
- handling paths with trailing `/` as prefix, as documented.
The change was not split because these changes depend on each other and
splitting would break recursive matching between the commits.
Tests:
1. diffed output before and after is equal (!= the same)
2. manual testing of glob matching
Change-Id: I4347a60874e4f07e41bdee43cc312547bea99008
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch ports the last remaining use of cbfs_boot_locate() in the
Intel FSP drivers to the new CBFS API. As a consequence, there is no
longer a reason for fsp_validate_component() to operate on rdevs, and
the function is simplified to take a direct void pointer and size to a
memory-mapping of the FSP blob instead.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If1f0239eefa4542e4d23f6e2e3ff19106f2e3c0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52281
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch changes the vboot EC sync code to use the new CBFS API. As a
consequence, we have to map the whole EC image file at once (because the
new API doesn't support partial mapping). This should be fine on the
only platform that uses this code (Google_Volteer/_Dedede family)
because they are x86 devices that support direct mapping from flash, but
the code was originally written to more carefully map the file in
smaller steps to be theoretically able to support Arm devices.
EC sync in romstage for devices without memory-mapped flash would be
hard to combine with CBFS verification because there's not enough SRAM
to ever hold the whole file in memory at once, but we can't validate the
file hash until we have loaded the whole file and for performance (or
TOCTOU-safety, if applicable) reasons we wouldn't want to load anything
more than once. The "good" solution for this would be to introduce a
CBFS streaming API can slowly feed chunks of the file into a callback
but in the end still return a "hash valid/invalid" result to the caller.
If use cases like this become pressing in the future, we may have to
implement such an API.
However, for now this code is the only part of coreboot with constraints
like that, it was only ever used on platforms that do support
memory-mapped flash, and due to the new EC-EFS2 model used on more
recent Chrome OS devices we don't currently anticipate this to ever be
needed again. Therefore this patch goes the easier way of just papering
over the problem and punting the work of implementing a more generic
solution until we actually have a real need for it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I7e263272aef3463f3b2924887d96de9b2607f5e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52280
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Gerrit is able to add reviewers based on entries in the `MAINTAINERS`
file. For inclusion and exclusion matches either paths or regular
expressions can be used. The syntax is described in the header of the
file.
When matching a path, there are two sensible possibilities:
- `path/to/file` matches a file.
- `path/to/dir/` matches a folder including its contents recursively.
- `path/to/dir/*` matches all files in that folder, without recursing
into its subfolders.
The trailing slash in the second example is essential. Without it, only
the directory entry itself matches when, for example, the folder gets
deleted, renamed or its permissions get modified. Reviewers in the list
won't get added to changes of any files or directories below that path.
Thus, add a linter script to ensure a path match on a directory always
ends with `/` or `/*` as shown above.
Change-Id: I9873184c0df4a0b4455f803828e2719887e545db
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Instead of counting consecutive matches (in `j`), check for a second
match directly in the control flow. Also, add some dedicated variables:
* `tap`: Keeps track of the tap value that resulted in a match and
is eventually programmed into the hardware.
* `tap2`: Is just temporarily used to search for another edge.
Keeping `tap` sync'ed with the hardware has the benefit that we don't
need to read the programmed value back for later fixups.
Change-Id: I3ae541c39efdc695f5ca74bc757b2f009239ec93
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
When EC_GOOGLE_CHROMEEC_INCLUDE_SSFC_IN_FW_CONFIG is enabled and SSFC is
not set, all fw_config is invalidated. But for some platform this may
not be necessary, we can treat missing SSFC as zero and use other 32
bits of firmware config.
BUG=b:184809649
TEST=boot and check fw_config is not -1 even if ssfc is not set
BRANCH=zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I21c7b0d449a694d28ad7b3f14b035e3a5830030a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This commit enables HECI such that interface can be used from
userspace on the dedede mainboards.
BUG=b:184219504
TEST=Build and flash drawcia, verify that Intel Flash Programming Tool
can communicate with the Converged Security Engine.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I5b28c471d6554a5e14538073d48ef47da05936fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Verified that all accessed registers exist in all SoCs that use this
code (Carrizo, Mullins, Stoneyridge, Picasso and Cezanne at the moment)
and that the bit definitions match as well. Also at the time of writing
this patch only Picasso calls gpio_fill_wake_state, so dropping the
check won't change behavior. This also avoids having SoC specific code
that doesn't get selected by Kconfig options in the common AMD SoC
directory and also avoids having to add a check for SOC_AMD_CEZANNE to
support this functionality on Cezanne in a follow-up patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If770780a67776daf81744db1b635ffd402653a47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52223
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is no nb/amd/pi northbridge left in coreboot that could be paired
with the Bolton FCH, since the remaining nb/amd/pi northbridges all use
an integrated FCH (Avalon on Mullins and Kern on Carrizo) while Bolton
is a discrete FCH. I ran into this when verifying if the common soc/amd
GPIO functionality that gets added by selecting
SOC_AMD_COMMON_BLOCK_BANKED_GPIOS is valid for all chips selecting it
and that code isn't valid for Bolton that uses the old GPIO 100
interface.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iffe876bee96e42645e1be10730b78959b1c06d59
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52222
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Coverity reported false-positive possible memory overrun
in setup_calloc_test(). Change memset address to use actual
buffer instead of pointer stored in symbol value in order
to silence Coverity.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I19f0718c657d565e515157e66367573e08f51254
Found-by: Coverity CID 1452005
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52136
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The patch enables Bluetooth config in the devicetree and removes
non-existent Bluetooth PCI interface.
TEST=Verified by checking Garfield Peak controller's PID:VID(8087:0033) in
the lsusb ouput.
Output of lsusb:
Bus 004 Device 003: ID 0bda:8153 Realtek Semiconductor Corp. USB 10/100/1000 LAN
Bus 004 Device 002: ID 0bda:0411 Realtek Semiconductor Corp. 4-Port USB 3.0 Hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 003: ID 0781:55a9 SanDisk Corp. Dual Drive
Bus 003 Device 004: ID 413c:2113 Dell Computer Corp. Dell KB216 Wired Keyboard
Bus 003 Device 002: ID 0bda:5411 Realtek Semiconductor Corp. 4-Port USB 2.0 Hub
Bus 003 Device 005: ID 8087:0033 Intel Corp.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I7a54d344ef1b0418bee56e7308977a61604b954a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52182
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the power state to return to when the power is re-applied
after power failure.
BUG=b:183739671
TEST=Build and Boot to OS in Majolica and Guybrush. By default when the
power fails the device turns on after power is re-applied. When the
POWER_ON_AFTER_POWER_FAILURE is disabled, the device remains off even
after the power is re-applied.
Change-Id: I21c5da08c82156d6239450ef6921771da74cbaa1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52049
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Introduce a power management library to handle the power resume after
power failure. Enable HAVE_POWER_STATE_AFTER_FAILURE config when this
library is enabled.
BUG=b:183739671
TEST=Build Guybrush and Majolica mainboard.
Change-Id: Iea4ea57d747425fe6714d40ba6e60f2447febf28
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Wrap `r` in parentheses to avoid unexpected behavior with compound
expressions. Fortunately, all uses of this macro do not cause issues.
Tested with BUILD_TIMELESS=1, Roda RK9 remains identical.
Change-Id: Id0f05a507c5e7e8c50e9765261d86bae73c7b5a6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The `CLKCFG_UPDATE` macro is copied from gm45 and unused. Correct it and
use the CLKCFG macros instead of magic values.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: I17e972eba21282ac84c7afe10b7149cd1131fd07
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51877
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Breaking strings across multiple lines hurts greppability. Refactor the
code a bit to drop one indentation level, and then reflow the strings.
Change-Id: I0accdfd0d2c5f58e4da493ba0d4b5c6a067d92c3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51876
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are some cases in `northbridge_topology_init` where condensing the
operation using one macro changes the binary, and have been left as-is.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I59c7d1f8d816b95e86d39dcbf7bc7ce8c34f0770
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51865
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The {MCH,DMI,EP}BAR macros can be used for both reading and writing.
While this can sometimes be useful, compile-time overflow checking is
limited. Moreover, and-masks need to be bit-wise negated, which is easy
to forget and may result in spurious overflow warnings, and silencing
them with a cast also suppresses true integer overflow issues.
To address these limitations and for consistency with the existing MMIO
API (arch/mmio.h and device/mmio.h), these macros will be replaced with
prefixed wrappers around MMIO API functions. However, existing platform
code needs to be refactored, and the risk of introducing regressions is
substantial. To minimize the risk of breakage, the bulk of the platform
code changes will be verified using reproducible builds.
This patch introduces the new accessors, to be put to use in follow-ups.
These accessors are implemented as macros so that subsequent commits can
be verified using reproducible builds. They will be replaced with actual
functions after refactoring all platforms.
Change-Id: I85376a9e2f6cd042b41036f90de7f9edc7ad4508
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51864
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
cbfs_mcache_real_size() has a subtle flaw: when the cache is perfectly
full to the end (so that the termination token sits exactly at the end
of the available space), the loop counting the size ends prematurely.
This means that when migrating the cache to CBMEM the terminating token
is not copied, which isn't actually noticeable unless you're looking for
a file that's not in the cache (because it doesn't exist or because not
all files fit when building).
This patch fixes the problem and slightly changes the error message for
when a cache isn't terminated (to make it more clear that this is a
different condition from a "normal" cache overflow that can happen when
building if there's not enough room to fit all files).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I8d89e7dadc958f97b173b3a2352f2010c8a3d1d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Rename the Kconfig parameter to more accurately reflect what it does.
TPM can be initialised in a different stage too, for instance with
VBOOT it is done in verstage.
Change-Id: Ic0126b356e8430c04c7c9fd46d4e20022a648738
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Some tests have to be able to catch assertion errors.
Adding CMocka mock_assert() enables that.
Additionally fix test_imd_create_tiered_empty(),
test_full_stack() and test_incorrectly_initialized_stack()
by adding missing expect_assert_failure().
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I5e8dd1b198ee6fab61e2be3f92baf1178f79bf18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
LANG LC_ALL TZ are required for reproducible builds. Those environment should
be always used for all builds in coreboot and for payloads.
By using COREBOOT_EXPORTS those would be removed in payload builds.
Change-Id: Iea965abbce23bf6ec408ef587da0a4c4ebc65a27
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some eMMCs need 80+ms for CMD1 to complete. And the payload may need to
access eMMC in the very early stage (for example, Depthcharge needs it
20ms after started) so we have to start initialization in coreboot.
On Hayato Chromebook this can save ~100ms in total.
BUG=b:177389446
TEST=emerge-asurada coreboot
BRANCH=asurada
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I2f58d203e969dc1a13a479d7dc63b1b162a9ae3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51973
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The conversion to ASL 2.0 syntax in commit 81d55cf introduced a
regression triggering a BUG in Linux when reading the battery current.
Correct the wrongly-converted calculation.
Fixes: 81d55cf ("src/ec/lenovo/h8/acpi/battery.asl: Convert to ASL 2.0")
Tested-by: Andrew A. I. <aidron@yandex.ru>
Change-Id: I1cea8f56eb0a674005582c87cad89f10a02d0701
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52144
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When GPIO_2 was configured as PAD_NF with the WAKE_L function selected
the GPIO_2 override in soc_gpio_hook called soc_route_sci that wrote the
corresponding SCI mapping register, but didn't set up the SCI level and
trigger type, so that couldn't have worked on most of the boards. The
only boards where I think this was actually tested are the google/zork
ones and they configured GPIO_2 as PAD_SCI where the GPIO mux setting is
GPIO mode instead of the WAKE_L mode, but at least the SCI was
configured correctly. The new PAD_NF_SCI macro can configure both the
right GPIO mux setting and set up the SCI configuration correctly, so
use this new macro for the GPIO_2 pin. For test purposes I also added
the corresponding GPIO_2 configuration to amd/mandolin to see if the
affected registers end up having the expected value using the HDT
debugger to look at the registers, but didn't test the wake-up
functionality, since S3 resume isn't working on amd/mandolin yet.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: Ic069e46b759fb6746645faccd254263c49a892d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51756
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit includes makefile cleanup to exclude common source file
compilation in each stage by using all-y flag.
BUG=b:182963902
TEST=trogdor validated on limozeen
Change-Id: I48464567974a0729c1c6b6157bcce4fac39a8b38
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
To train PCIe devices, the devices need to be enabled and taken out of
reset. This patch does the bare minimum needed to train PCIe. It is
not intended to handle timings, which will be addressed later.
Copy the enables for WWAN & WLAN into early GPIO Init so that they're
enabled before FSP-M runs and trains the PCIe busses.
Again, this patch is the minimum to let the FSP train the PCIe busses.
BUG=b:182202136
TEST=Boot guybrush from NVME.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3807e02de1e9ae40b0a4162217afd6aabb5b04ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52115
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds the functionality to write the DXIO and DDI descriptors
to the UPD data structure to the SoC code and adds the
mainboard_get_dxio_ddi_descriptors function to each mainboard using the
Cezanne SoC that gets called to get the descriptors from the board code.
Change-Id: I1cb36addcf0202cd56ce99e610a13d6d230bc981
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51948
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The UPD header files get generated as part of the FSP build process. For
the initial Cezanne development we took the Picasso UPD data structures
as a starting point. This patch replaces it with the first version of
the Cezanne-specific UPD data structures that is present in version 12
of the internal work-in-progress FSP binary drops.
The serial_port_stride UPD-M field is removed, since the information is
already given by serial_port_use_mmio. The stride is 4 bytes for the
MMIO UART case and 1 byte for the legacy I/O case.
BUG=b:182524631
TEST=NVMe works on google/guybrush when the rest of the patch train is
applied as well.
Change-Id: Idca235029bf2e68d403230d55308820cab61a6c0
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
mb/google/guybrush: Update APCB - disable debug
mb/google/guybrush: Add APCB to get through memory training
soc/mediatek/mt8192: Add EMI Settings of 8GB Normal Mode
soc/mediatek/mt8192: Update MCUPM firmware
soc/mediatek/mt8192: Add version info for SSPM
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I445d753c712670fe80efcdf29459736df2b76666
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
On VCCin there was an oscillation which occurred just as the kernel
started (kernel starting... message). On some devices, this behavior
seems even worse. In previous platforms VCCin toggled for a few ms
and then was stable. For volteer, this happens at the same point in
time for around 40ms. However, it starts oscillating again later in
the boot sequence. Once at the root shell, it seems to oscillate
indefinitely at around 100-200Hz (very variable though). To fix this
we need to control the deep C-state voltage slew rate.We have options
for controlling the deep C-state voltage slew rate through FSP UPDs.
This patch expose the following FSP UPD interface into coreboot:
- AcousticNoiseMitigation
- FastPkgCRampDisable
- SlowSlewRate
We are setting SlowSlewRate for all volteer boards to 2 which is Fast/8.
TGL has a single VR domain(Vccin). Hence, the chip config is updated to
allow mainboards to set a single value instead of an array and FSP UPDs
are accordingly set.
BUG=b:153015585
BRANCH=firmware-volteer-13672.B
TEST= Measure the change in noise level by changing the UPD values.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: Ica7f1f29995df33bdebb1fd55169cdb36f329ff8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
From Skylake/Sunrise Point onwards, there are two BIOS_CNTL registers:
one on the LPC/eSPI PCI device, and another on the SPI PCI device. When
the WPD bit changes from 0 to 1 and the LE bit is set, the PCH raises a
TCO SMI with the BIOSWR_STS bit set. However, the BIOSWR_STS bit is not
set when the TCO SMI comes from the SPI or eSPI controller instead, but
a status bit in the BIOS_CNTL register gets set. If the SMI cause is not
handled, another SMI will happen immediately after returning from the
SMI handler, which results in a deadlock.
Prevent deadlocks by clearing the SPI synchronous SMI status bit in the
SMI handler. When SPI raises a synchronous SMI, the TCO_STS bit in the
SMI_STS register is continously set until the SPI synchronous SMI status
bit is cleared. To not risk missing any other TCO SMIs, do not clear the
TCO_STS bit again in the same SMI handler invocation. If the TCO_STS bit
remains set when returning from SMM, another SMI immediately happens and
clears the TCO_STS bit, handling any pending events.
SPI can also generate asynchronous SMIs when the WPD bit is cleared and
one attempts to write to flash using SPI hardware sequencing. This patch
does not account for SPI asynchronous SMIs, because they are disabled by
default and cannot be enabled once the BIOS Interface Lock-Down bit in
the BIOS_CNTL register has been set, which coreboot already does. These
asynchronous SMIs set the SPI_STS bit of the SMI_STS register. Clearing
the SPI asynchronous SMI source should be done inside the SPI_STS SMI
handler, which is currently not implemented. All of this goes out of the
scope of this patch, and is currently not necessary anyway.
This patch does not handle eSPI because I cannot test it, and knowing if
a board uses LPC or eSPI from common code is currently not possible, and
this is beyond the scope of what this commit tries to achieve (fix SPI).
Tested on HP 280 G2, no longer deadlocks when SMM BIOS write protection
is on. Write protection will be enforced in a follow-up.
Change-Id: Iec498674ae70f6590c33a6bf4967876268f2b0c8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50754
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some of the src/vendorcode/ directories are used to import a whole
codebase from somewhere else which uses a completely different coding
style. For those directories, excluding them from checkpatch makes
sense. However, other directories are simply implementing
vendor-specific extensions that were written by coreboot developers
specifically for coreboot in coreboot's coding style. Those directories
should be covered by checkpatch.
This patch narrows the existing blanket exception of src/vendorcode/ to
the amd, cavium, intel and mediatek directories (which actually include
large amounts of foreign source). The eltan, google and siemens
directories (which seem to contain code specifically written for
coreboot) will now be covered by checkpatch.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I1feaba37c469714217fff4d160e595849e0230b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51827
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch disables checkpatch warnings about two style constructs that
are not illegal in coreboot style and can in my opinion be useful in
certain situations.
The first is an assignment in if conditions like this:
if ((ret = func()))
return ret;
This can save a line compared to the alternative construct which may
help readability, especially in functions that need to do a lot of
these. More importantly, the while-equivalent of this construct is not
forbidden (and a lot more useful, because certain things become very
complicated to write without it), and it seems weird to forbid one but
not the other. We already have GCC warnings that enforce an extra set
of parenthesis to highlight that this is an assignment instead of a
comparison, so the risk of typos or confusion between those two is
already mitigated anyway.
The second is the use of `else` after return like this:
if (CONFIG(TYPE_A))
return response_for_type_a;
else
return response_for_type_b;
While the else is redundant in this case, it serves to highlight the
symmetry and equivalence in importance of the two paths. There are
certainly other situations where the construct of
if (something_went_wrong)
return error;
if (something_else_went_wrong)
return other_error;
if (...)
is more useful, but this usually suggests an "either abort here or
continue on the main path" style flow, whereas the code with `else` is
more suitable to highlight an "either one or the other" flow with two
equal-weighted options. I think the programmer should pick which style
best represents the intentions of their code in these cases, and don't
understand why one of the two should be categorically forbidden.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I130598057c1800277a129ae6b927e961d6e26e42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51551
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With the current version method, it's not possible to determine if
a different version is older or newer than the current version without
digging into the repository and finding the dates for the version
numbers.
This change adds the commit date to the start of the toolchain version
which will let us tell at a glance how old or new the toolchain is.
It's not perfect because multiple toolchain commits can go in on the
same day, but adding the time made the string even longer, and really
doesn't help that much.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I9c6d27667b922dc15e7a6e132e1beff69eed839c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
TPM_INIT is disabled by default. This prevents TPM to be operational
when VBOOT is disabled.
Remove the TPM_INIT disable.
BUG=N/A
TEST=tested on facebook monolith with VBOOT disabled.
Change-Id: I84d525a18c84643903922fef0a11dcf98abbbe4d
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52052
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
This patch changes the mem_pool implementation to track the last two
allocations (instead of just the last) and allow them both to be freed
if the mem_pool_free() calls come in in reverse order. This is intended
as a specific optimization for the CBFS cache case when a compressed
file is mapped on a platform that doesn't natively support
memory-mapping flash. In this case, cbfs_map() (chaining through to
_cbfs_alloc() with allocator == NULL) will call
mem_pool_alloc(&cbfs_cache) to allocate space for the uncompressed file
data. It will then call cbfs_load_and_decompress() to fill that
allocation, which will notice the compression and in turn call
rdev_mmap_full() to map the compressed data (which on platforms without
memory-mapped flash usually results in a second call to
mem_pool_alloc(&cbfs_cache)). It then runs the decompression algorithm
and calls rdev_munmap() on the compressed data buffer (the latter one in
the allocation sequence), leading to a mem_pool_free(). The remaining
buffer with the uncompressed data is returned out of cbfs_map() to the
caller, which should eventually call cbfs_unmap() to mem_pool_free()
that as well. This patch allows this simple case to succeed without
leaking any permanent allocations on the cache. (More complicated cases
where the caller maps other files before cbfs_unmap()ing the first one
may still lead to leaks, but those are very rare in practice.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ic5c4c56a8482752ed65e10cf35565f9b2d3e4b17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
RETURN_FROM_VERSTAGE is a somewhat tricky construct that we don't
normally do otherwise in coreboot. While it works remarkably well in
general, new development can lead to unintentional interactions with
confusing results. This patch adds a debug print to the verstage right
before returning to the bootblock so that it's obvious this happens,
because otherwise in some cases the last printout in the verstage is
about some TPM commands which can be misleading when execution hangs
after that point.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9ca68a32d7a50c95d9a6948d35816fee583611bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52086
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CBFS_VERIFICATION requires the CBFS metadata hash anchor to be linked
into an uncompressed stage, but for platforms using COMPRESS_BOOTBLOCK,
this is only the decompressor stage. The first CBFS accesses are made in
the bootblock stage after decompression, so if we want to make
CBFS_VERIFICATION work on those platforms, we have to pass the metadata
hash anchor from the decompressor into the bootblock. This patch does
just that. (Note that this relies on the decompressor data remaining
valid in memory for as long as the metadata hash anchor is needed. This
is always true even for OVERLAP_DECOMPRESSOR_ROMSTAGE() situations
because the FMAP and CBFS metadata necessarily need to have finished
verification before a new stage could be loaded.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I2e6d7384cfb8339a24369eb6c01fc12f911c974e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52085
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds file data hashing for CONFIG_CBFS_VERIFICATION. With
this, all CBFS accesses using the new CBFS APIs (cbfs_load/_map/_alloc
and variants) will be fully verified when verification is enabled. (Note
that some use of legacy APIs remains and thus the CBFS_VERIFICATION
feature is not fully finished.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ic9fff279f69cf3b7c38a0dc2ff3c970eaa756aa8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
With the last external user to cbfs_load_and_decompress() gone, we can
stop exporting this function to the rest of coreboot and make it local
to cbfs.c. Also remove a couple of arguments that no longer really make
a difference and fold the stage-specific code for in-place LZ4
decompression into cbfs_prog_stage_load().
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I4b459650a28e020c4342a66090f55264fbd26363
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
These p-suffixed helpers allow dropping pointer casts in call-sites,
which is particularly useful when accessing registers at an offset from
a base address. Move existing helpers in chipset code to arch/mmio.h and
create the rest accordingly.
Change-Id: I36a015456f7b0af1f1bf2fdff9e1ccd1e3b11747
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51862
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 023fdaffd1 (mb/asus/p2b: Refactor southbridge ACPI stuff)
moved the southbridge ACPI stuff to its own file. It also
(prematurely) listed PM and SMBus I/O port ranges as a #defined
fixed value.
Since these two ranges are not expected to change at runtime anyway,
we can simply drop the ASL code doing the read.
Change-Id: Id5adb37d047621d7c8faf81607ceea4cbcac3d34
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41093
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Haswell MRC.bin can return zero even when raminit did not complete
successfully. When this happens, the memory controller will not have
acknowledged raminit: the mc_init_done_ack bit in the MC_INIT_STATE_G
register will be zero, and memory accesses will lock up the system.
To handle this situation more gracefully, check the mc_init_done_ack bit
after running MRC. If the bit is not set, log a fatal error and halt.
Tested on Asrock B85M Pro4:
- With badly-seated DIMMs, MRC raminit fails and coreboot dies.
- After reseating the DIMMs, the board still boots successfully.
Change-Id: I144bf827f65cd0be319c44bf3d407ddc116b129d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Each TCSS DMA is grouped together with two PCIe RPs in terms of PM flow.
This change ensures that SD3C is updated for the TCSS DMA devices
corresponding to the TBT RP ports. If TBT port is 0 or 1, SD3C for DMA0
is updated, else for DMA1.
BUG=None
TEST=Built Alderlake image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia3462dfbb287a374960a57bb4c3541db2a435611
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51965
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current get panel_id is over sku_id() >> 4, but sku_id is combined with
wfc_id/lcm_id/sku_id, so the panel_id value is wfc_id << 4 | lcm_id()
in fact. When wfc_id is not 0, the panel_id will be wrong. So only get
the low 4 bits for the panel_id.
BUG=b:183779755
BRANCH=kukui
TEST=emerge-kukui
Change-Id: I63e0c8a2719462a9b979afe52a27c78b9fc804e8
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
It is a bug acknowledged by Intel (IPS case 00600003) that has been
fixed for SRP but won't be fixed for CPX.
This fixes field offsets for fields that follow SYSTEM_STATUS.RcVersion
Change-Id: I5248734e2f086d39bb75b7b1359e60dfd8704200
Signed-off-by: Deomid "rojer" Ryabkov <rojer9@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
VENDORCODE_ELTAN_MBOOT should not be used when VBOOT is enabled.
Hide VENDOCODE_ELTAN_MBOOT when VBOOT is enabled.
BUG = N/A
TEST = run `make menuconfig` and boot Facebook FBG1701
Change-Id: Iac57103431cc7efac5b6019f180572d255e683ab
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
All known on-chip PCI devices are disabled in the chipset devicetree.
So they are removed from the mainboard devicetree.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: Ie67cd8afc9ea92e9fd7caed4338cb25a68d94cb1
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Some functions/macros like assert() require redefinition for testing
purposes. ENV_TEST is introduced to make it possible without using
bypass hacks.
This patch also adds a global __TEST__ define to TEST_CFLAGS for
all test targets in order to enable ENV_TEST.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Ib8f2932902a73a7dbe181adc82cc18437abb48e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Replace the mainboard-specific code for "POST complete" signalling with
devicetree entries for using the newly introduced IPMI driver
functionality.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Change-Id: I7503dec4e72810db8dfe74f72638b466a3d66748
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48671
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On OCP Tioga Pass the pad GPP_B20 is used as output for signalling "POST
complete" to the BMC. According to the schematics and the code in
`ramstage.c`, the signal is active-low. There is an external pull-up
resistor.
To make the signalling work as it should, set the initial output value
to `high`.
Change-Id: I82fbda1caba9163ba3b2e38f494a0cefa27e657f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48670
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TPM_INIT depends on VBOOT but should also depend on
VENDORCODE_ELTAN_xBOOT.
Add dependency. TPM_INIT will be enable for measured boot only.
BUG = NA
TEST = Boot Facebook FB1701 with possible combinaties of VBOOT, measured
boot and eltan security.
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Change-Id: I03f8457731c73c653bd82b1042bda3fc2d797feb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
The recent refactor of console UART GPIOs to mainboard's bootblock
caused brya boards to lose the first ~5 lines of the logs from
bootblock. Rename bootblock_mainboard_init to
bootblock_mainboard_early_init so that the UART pads will be ready
by the time the console is initialized.
BUG=b:184319828
TEST=First lines from report_platform.c are now seen in UART output
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4a4fadcc091bf9b1c9894f9afaf42baff63c73a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Background story (I think that's what great in opensource -
ppl leave there part of their lives): ;-)
While trying to fix audio jack not working with coreboot and
Windows 10 with some help from hell__ and nico_h on IRC nico_h
discovered that t420 and t430 hda_verb.c are the same:
<nico_h> oddly, in coreboot source T420 and T430 have the same
numbers for very different codecs... I suspect copy-pasta
Difference between /sys/class/sound/cardX/hwCXDY/init_pin_config
in vendor BIOS helped with the updated config. Connecting audio
jack now works flawless both in Linux and Windows.
Audio-related keyboard buttons: volup, voldown, mute works fine
both in Linux (Debian-based) and Windows 10. mutemic button works
(tested ie. with xev) but both in Linux and Windows 10 wont light
up or makes any effect.
+-----------------------------------+
| init_pin_config dump from: |
+----= VENDOR =---+---= coreboot =--+
| 0x19 0x04211040 | 0x19 0x04211040 |
| 0x1a 0x61a19050 | 0x1a 0x61a19050 |
| 0x1b 0x04a11060 | 0x1b 0x04a11060 |
| 0x1c 0x6121401f | 0x1c 0x6121401f |
| 0x1d 0x40f001f0 | 0x1d 0x40f001f0 |
| 0x1e 0x40f001f0 | 0x1e 0x40f001f0 |
| 0x1f 0x90170110 | 0x1f 0x90170110 |
| 0x20 0x40f001f0 | 0x20 0x40f001f0 |
| 0x22 0x40f001f0 | 0x22 0x40f001f0 |
| 0x23 0x90a60170 | 0x23 0x90a60170 |
+-----------------+-----------------+
Tested-by: Piotr Szymaniak
Signed-off-by: Piotr Szymaniak <szarpaj@grubelek.pl>
Change-Id: Ie5eba84e5ea590b7db00e189cd68e714bee7e410
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51612
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Intel FSP 2.0 driver contains a custom construct that basically
serves the same purpose as the new CBFS allocator concept: a callback
function to customize placement of a loaded CBFS file whose size is
initially unknown. This patch removes the existing implementation and
replaces it with a CBFS allocator.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0b7b446a0d2af87ec337fb80ad54f2d404e69668
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Right before CB:49334 was submitted, I changed the signature of
cbfs_allocator_t function pointers to include another argument passing
in the already loaded CBFS metadata (to allow for the rare edge case of
allocators needing to read CBFS attributes). This interface is not meant
to be able to modify the passed-in metadata, so to clarify that and
prevent potential errors, we should declare the argument const.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I7e3756490b9ad7ded91268c61797cef36c4118ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable I2C2 in devicetree and fill ACPI information for Codec and
Speaker amplifiers. Pass correct IRQ GPIO for headset jack.
BUG=None
BRANCH=None
TEST=Ensure that the Codec and Speaker Amplifiers are detected in
i2cdetect.
Change-Id: I1ae52a8bbaa0181c906cd14a94de22e0250ed4c1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52046
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the BT disable GPIO to logic low in order to enable Bluetooth.
Add USB ACPI configuration for BT device.
BUG=b:182201890
TEST=Build and boot to OS.
Change-Id: I647c301e2db6d4a7c5c8cb31cbc47a44cba5e734
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Initialize all eSPI signals including PCIE_RST0_L early for EC
communication.
- Set PCIE_RST0_L to a GPIO and set it high to release the bus. This is
a temporary workaround until PCIE_RST_L comes up on its own.
- Make sure all GPIO muxes initialized early are re-initialized.
BUG=b:183340503
TEST=Boot Guybrush
Change-Id: I512cb8b435dc8412cd46189e741ad94e5a24699e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51675
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Enable warnings
- Enable warnings as errors
- Remove debug flag -g
- Add targets for all, distclean, and help
- Add dependency of the bincfg file for output targets
- Add all phony targets to .PHONY
BUG=None
TEST=Build all targets
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ic0302f663cbc931325334d0cce93d3b0bf937cc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50654
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
espi_setup already clears most of the controller registers. So this
change consolidates the clear logic into one spot.
This shouldn't result in a behavior change on Picasso. Picasso already
has the eSPI decodes clear on boot, so this change is a nop.
BUG=b:183524609
TEST=Boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic57689e50febd29796d8ac8d99c81e41fee5b41c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is only ever called after espi_setup.
55861 - AMD System Peripheral Bus Overview also says that io ranges
should be configured before enabling the BUS_MASTER bit.
BUG=b:183524609
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I074e487d8768a578ee889a125b9948e3aa6c7269
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Configure I2C rise/fall time in device tree to ensure I2C CLK runs
accurately at I2C_SPEED_FAST (< 400 kHz).
Measured I2C frequency just as below after tuning:
I2C0(touchpad): 385 kHz
I2C4(audio): 380 kHz
BUG=b:180335053
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400kHz
Change-Id: Ic92ee0379456e80260a8026bc38ee41325dad6d2
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This sets the eSPI registers to the reset values specified in the PPR.
On Cezanne, the PSP modifies these registers such that the eSPI
peripheral cannot send DEFER packets. This causes random bus errors.
These reset values are identical to what is currently used on Zork.
I didn't clear out ESPI_DECODE because it's currently being done by
cb:51749.
BUG=b:183524609
TEST=Boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic3a9860747aac78121358b4499d8a38052236c0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There are forthcoming designs that will be utilizing
a discrete TPM 2.0 solution. Split the existing dedede
configuration options so future mainboard variants can
easily select the appropriate Kconfig option using the
newly introduced options:
- BOARD_GOOGLE_BASEBOARD_DEDEDE_CR50
- BOARD_GOOGLE_BASEBOARD_DEDEDE_TPM2
The existing variants all select the former option,
BOARD_GOOGLE_BASEBOARD_DEDEDE_CR50 since all those
designs currently utilize Cr50.
BUG=b:184151664
Change-Id: I2bdb1ca4fd78cc0628256d49678ea042c55f6fba
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52030
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP v2081 has a bug where it uses the information about south XHCI
ports to enable TCSS XHCI ports. This change works around this bug by
enabling south XHCI ports 1 and 2 in brya baseboard devicetree. brya0
already enables south XHCI port 1 in overridetree.cb, however, it is
still enabled in baseboard/devicetree in case more variants are added
to brya before FSP is fixed.
BUG=b:184324979
TEST=Verified that TCSS XHCI ports 1 and 2 are now enabled.
Change-Id: I4b86a98b18234ba309ddf2f30b80d78472951637
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
There's no good reason to use values smaller than 2 GiB here. Well, it
increases available DRAM in 32-bit space. However, as this is a 64-bit
platform, it's highly unlikely that 32-bit limitations would cause any
issues anymore. It's more likely to have the allocator give up because
memory-mapped resources in 32-bit space don't fit within the specified
MMIO size, which can easily occur when using a discrete graphics card.
Change-Id: If585b6044f58b1e5397457f3bfa906aafc7f9297
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52072
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's no good reason to use values smaller than 2 GiB here. Well, it
increases available DRAM in 32-bit space. However, as this is a 64-bit
platform, it's highly unlikely that 32-bit limitations would cause any
issues anymore. It's more likely to have the allocator give up because
memory-mapped resources in 32-bit space don't fit within the specified
MMIO size, which can easily occur when using a discrete graphics card.
Change-Id: I6cdce5f56bc94cca7065ee3e38af60d1de66e45c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52070
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop unnecessary typedefs and rename DDR4-specific definitions to avoid
name clashes, as done for DDR3 in earlier commits. This allows including
and using both DDR3 and DDR4 headers in the same compilation unit.
Change-Id: I17f1cd88f83251ec23e9783a617f4d2ed41b07f0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51898
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Cezanne PSP configures the eSPI with the assumption that it's a
majolica, setting up both the serial port and the majolica EC IO decode
ranges. Since guybrush is NOT a majolica, this doesn't work very well
there. Clearing the decode ranges allows the guybrush platform to set
the decode ranges needed for its EC.
BUG=b:183524609
TEST=Set up eSPI on Guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I77cfb948cb9ae6d1cf001bd9e66cede8d93f50b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Previously, the eSPI code would only add to existing decode ranges, and
there wasn't any way to clear ranges. This clears all the ranges so
the eSPI configuration can start fresh.
BUG=b:183207262, b:183974365
TEST=Verify on Guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ic4e67c40d34915505bdd5b431a064d2c7b6bbc70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
These used to be printed before CB:46605. Having them in the logs can be
a huge timesaver when debugging logs sent to you by other people
(especially from systems that don't boot all the way). Let's add them
back.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ifdbfdd29d25a0937c27113ace776f7aec231a57d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Ideally we would like to perform EC Software Sync in payload. But with
the hardware requirement (EC_IN_RW) and firmware requirement (TPM
command to get EC execution environment) not met yet, adding the support
to perform early EC Software sync. With EFS2 enabled, this will also
help cr50 to set the boot mode as NORMAL instead of NO_BOOT.
BUG=None
TEST=Build and Boot to OS in Guybrush. Ensure that the EC software sync
is successfully complete.
CBFS: Found 'ecrw.hash' @0x50400 size 0x20 in mcache @0x020171ec
VB2:check_ec_hash() Hexp RW(active): 2dd8dbb78d0c626358a626037973a3d81982f88f3f38e7f759039bf84e05ccc6
VB2:check_ec_hash() Hmir: 2dd8dbb78d0c626358a626037973a3d81982f88f3f38e7f759039bf84e05ccc6
<snip>
VB2:check_ec_hash() Heff RW(active): 2dd8dbb78d0c626358a626037973a3d81982f88f3f38e7f759039bf84e05ccc6
VB2:sync_ec() select_rw=RW(active)
Change-Id: I820e651c6b22a833fef6f17a4ceb5a8cfb6f1616
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Enable Touchpad by configuring the enable GPIO to logic high. Add
touchpad configuration for ELAN touchpad.
BUG=b:182207444
TEST=Build and boot to OS in Guybrush. Ensure that the trackpad events
are detected using evtest.
Change-Id: Ib47fbb33f2b181eb85f6ded98a5b0ce08fbc7b64
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51962
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change disables touchpad interrupt, as it sends spurious wake signal
via GPP_F14 and immediately wakes the system from S3. It happens because
touchpad's power is gated by deassertion of PLTRST#. The behaviour for
S0ix is unchanged.
BUG=183738135
TEST=manually
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: Ia7d282f38d205a94cc43eaa1832729f4606437c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51831
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PCH_INT_ODL (GPP_F17) is used to wake AP from S3, however it was configured
to reset state on PLT reset assertion. This change reconfigures the pad
using DEEP instead of PLTRST to retain pad configuration across S3.
BUG=b:178545523
TEST=manual: verified that asserting PCH_INT_ODL wakes system and the wake
source is GPP_F17
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: I8df5dafedabc7b6af74c39621f0e1eb7019a9a17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reference code does an and-or operation with zero as or-value, reading
and writing to the same address. The accessed register is 32-bit, and
reference code programs bits 22, 21, 20, 16 to zero. However, coreboot
code reads the value from bits 7..0 instead. Correct this.
Change-Id: I33bf268449c2f799321be81a02bbccff855ee1fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51861
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We've mostly stopped using Trogdor-rev0 now and are starting to bring up
rev2 instead. Therefore, the default revisions this builds for should be
the newer ones.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie433ebb2a03fb1636b5012b4a0567ba6f982579d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52007
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The is used for AMD Grunt board which uses ALC5682 and MAX98357 codec.
kernel driver will need to retrieve MISC FCH memory resource for CLK
enabling per different CID/HID.
BUG=b:171755306
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I5f29a2d784a9fc749fff61a9c96c0a487b71a2d7
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51659
Reviewed-by: Yu-hsuan Hsu <yuhsuan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable Acoustic noise mitigation for lantis and set slew rate to 1/4
which is calibrated value for the board. Other values like PreWake,
Rampup and RampDown are 0 by default.
BUG=b:183561593
BRANCH=dedede
TEST=EE verify acoustic noise test passes.
Change-Id: I5e5f24ed934910726c220678068d085b6ee2bcf6
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Needed so get_lid_switch will actually call the EC. Otherwise it
returns -1.
BUG=b:183524609
TEST=Depthcharge no longer halts complaining that coreboot didn't sample
the pin
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4639b3713d726192e251dcffa14381dd92518fa2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
It looks like we are having SI issues on eSPI at 33 MHz. Switching to 16
MHz makes everything a lot more stable.
BUG=b:183524609
TEST=Boot to OS and run `ectool version` 1000 times and see no problems.
Before with 33 MHz there was an error every few cycles.
declare -i i=0; while ectool version; do i+=1; echo "$i"; sleep .11; done; echo "Finished: $i"
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6ab515629703a157c1d1ac6adcf5cf379e80f8ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Causing the AOAC register access as part of system suspend (S3) causes
the suspend procedure to be stuck. Comment it for now to unblock
entering S3 and collecting the power numbers.
BUG=b:181766974
TEST=Build and boot to OS in Majolica. Enter S3 through "echo mem >
/sys/power/state".
Change-Id: Ie93bbe393b209b784b9a2257f3916b29d84b25d1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51926
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PCR algorithms used for vboot are frequently causing confusion (e.g.
see CB:35645) because depending on the circumstances sometimes a
(zero-extended) SHA1 value is interpreted as a SHA256, and sometimes a
SHA256 is interpreted as a SHA1. We can't really "fix" anything here
because the resulting digests are hardcoded in many generations of
Chromebooks, but we can document and isolate it better to reduce
confusion. This patch adds an explanatory comment and fixes both
algorithms and size passed into the lower-level TPM APIs to their actual
values (whereas it previously still relied on the TPM 1.2 TSS not
checking the algorithm type, and the TPM 2.0 TSS only using the size
value for the TCPA log and not the actual TPM operation).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib0b6ecb8c7e9a405ae966f1049158f1d3820f7e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Pronin <apronin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This add an option to generate BPM using the 9elements bg-prov tool
using a json config file.
A template for the json config file can be obtained via
"bg-prov template".
Another option is to extract it from a working configuration:
"bg-prov read-config".
The option to just include a provided BPM binary is kept.
Change-Id: I38808ca56953b80bac36bd186932d6286a79bebe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50411
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adds initialisation of 512MB of DDR memory on the BBB to the romstage.
The parameters for the DDR peripherals are taken from U-Boot.
TEST: Booted from romstage into ramstage. Also successfully managed to
run the "ram_check" in lib.h.
Change-Id: I692bfd913c8217a78d073d19c5344c9bb40722a8
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Adds code taken and (barely) adapted from U-Boot (release 2020.04,
commit 36fec02b1f90b92cf51ec531564f9284eae27ab4) for SDRAM initialization.
This should in theory work for other configurations than the Beaglebone
Black's DRAM configuration, but hasn't been tested.
Change-Id: Ib1bc2fa606f7010c8c789aa7a5c37cd41bc484b9
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44386
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adds a "sd_media" boot_device to allow booting from the SD card. This
assumes that the generated "MLO" file is placed at a 128KB offset from
the start of the SD card, to allow for the MBR etc. to be at the start
of the SD card. Placing the MLO file here allows the AM335x boot ROM to
load and execute the bootblock stage as well, as 128KB is one of the
offsets the boot ROM checks when looking for the next stage to execute.
As part of this, a FMD for the Beaglebone has also been defined. It's
sized at 32M somewhat arbitrarily, as SD cards could allow for much
bigger payloads.
TEST: Beaglebone boots from bootblock into romstage. Romstage to
ramstage still doesn't work as it needs RAM initialization first.
Change-Id: I5f6901217fb974808e84aeb679af2f47eeae30fd
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44385
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adds a driver for the am335x MMC peripheral. This has only been tested
with SD cards and probably needs some modification to use eMMC or MMC
cards.
It's also currently a little slow as it only supports reading a block at
a time.
Change-Id: I5c2b250782cddca17aa46cc8222b9aebef505fb2
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Fix the format warning below by using `PRIxPTR`, which is defined as
unsigned long.
src/soc/amd/common/block/smbus/smbus.c:33:56: error: format specifies type 'size_t' (aka 'unsigned int') but the argument has type 'uintptr_t' (aka 'unsigned long') [-Werror,-Wformat]
printk(BIOS_ERR, "Invalid SMBus or ASF base %#zx\n", mmio);
~~~~ ^~~~
%#lx
src/include/console/console.h:60:61: note: expanded from macro 'printk'
#define printk(LEVEL, fmt, args...) do_printk(LEVEL, fmt, ##args)
~~~ ^~~~
1 error generated.
Change-Id: I727c490d3097dcf36cdbcd4db2852cd49d11785f
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Move the parts of romstage.c that populate the UPD-M data structure to
the newly created fsp_m_params.c file. Since
platform_fsp_memory_init_params_cb gets called from the FSP driver and
not directly from car_stage_entry the two code parts in romstage.c
weren't directly interacting.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1f7f5879ac318372042ff703ebbe584ce1c32c91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Move the parts of romstage.c that populate the UPD-M data structure to
the newly created fsp_m_params.c file. Since
platform_fsp_memory_init_params_cb gets called from the FSP driver and
not directly from car_stage_entry the two code parts in romstage.c
weren't directly interacting. Since soc/romstage.h only contains the
mainboard_updm_update function prototype, rename it to soc/fsp.h. This
patch also removes a few unused includes.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I52c21f13520dbdfab37587d17b3a8a3b1a780f36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This file populates the UPD-S data structure that gets passed to the
FSP-S, so add that s part to make it a bit clearer which FSP parameters
it'll set up. This is also a preparation to add a fsp_m_params.c file in
the following patches.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I53786df0909055e66eac675b5580909b7960944f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The KBRST_L pin will cause a reset when driven or pulled low even when
the GPIO mux is set to GPIO and not native function. So when you want to
use that pin as general purpose output the keyboard reset input
functionality needs to be disabled by selecting this option in the
board's Kconfig file to avoid causing a reset by writing a 0 to the
output level bit when it's configured as an output.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Furquan Shaikh <furquan@google.com>
Change-Id: I517ad551db9321f26afdba15d97ddb61be1f7d51
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51757
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This was copied from Sandy Bridge and does not apply to Ironlake. These
offsets go past the MCHBAR window (MCHBAR size is 16 KiB on Ironlake).
Some of these writes would have collided with `DEFAULT_HECIBAR` if the
PCI resource had been reported as fixed. Remove the copy-pasted code.
Change-Id: I7688921ad7517cbd68a0c48262b29ecf7b4c396c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51856
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
While 64-bit writes seem to work properly, there could be unknown
side-effects in some cases, e.g. when running in long mode. Since
reference code uses two 32-bit writes, follow suit.
Change-Id: I48ed3d94c7865b3a3cce52108e99cf1656b57fc2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51855
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Thermal sensor2 defined in baseboard do not exist in boten.
With the format the DPTF policies are defined in boten, all the entries
from the baseboard are included and then the overrides applied.
This causes the non-existent DPTF devices to be exported in the ACPI table
and in turn OS reading invalid temperatures. Fix the format for
DPTF passive and critical policies.
BUG=None
BRANCH=dedede
TEST=Build and boot to OS in boten. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Change-Id: I63c781e0a439f1e7a3525fa7cf290fa9300cb066
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ben Kao <ben.kao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Original Stamp_boost parameter will cause boost time over 2500sec(3960sec)
To pass balance performance and skin temperature test, decrease stamp_boost:
2500 -> 1640
BUG=b:182753072
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test
Change-Id: I43c104ef912aafecadf9497f9ea20c8478c0e920
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Updating from commit id 3a9d7cd:
2021-03-03 15:37:08 -0700 - (picasso: Update Dali SMU firmware)
to commit id dded82f:
2021-03-23 15:36:36 -0600 - (picasso: Update Dali SMU firmware)
This brings in 2 new commits.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: If71e52a2a3e50aeb8599798de7b49bc71ed26a04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
REG_BASE_SIZE is supposed to represent the size of the REGBAR MMIO space
in KiB. It is currently sized at 4MiB, but this is incorrect, EDS Vol. 2
indicates REGBAR is 16MiB in size, therefore update the constant to
reflect this.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I0cfbe5b8bb07faa854efd4bf70640daa117f2bb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The Type-C subsystem ("TCSS") IP block is similar between TGL and
ADL. For pre-boot purposes, the limited amount of functionality required
appears to be common between the two, therefore move the functionality
to intel/common/block and rename from `early_tcss to `tcss` along the way.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I1c6bb9c7098691f0c828f9d5ab4bd522515ae966
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51753
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds a pin configuration macro that supports both switching a
pin to its native function and configuring it as a SCI source. This is a
preparation to remove the GPIO2 soc_gpio_hook.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If0da5c010f35fd902f6b8857368daec93c12394a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50373
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Caroline has a Wacom W9013 digitizer on I2C2, which was
incorrectly disabled in commit d957d12e6
[mb/google/glados: clean up variant devicetrees]
as part of preparation for converting to overridetree format.
Test: build/boot, verify digitizer now available under Linux
Change-Id: I234bc0126b5d13c22a663d6544382890b312ce63
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
List of changes:
1. Add correct board Id for ADL-M LP5 configuration
2. Add spd hex files for LP5 Micron part
3. Update memory.c file with correct Dq-dqs and byte mapping for LP5
BUG=None
BRANCH=None
TEST=Build is successful for ADL-M RVP
Change-Id: I0bbd3f5b56bf7fbe918cc599d32a01dcae896ddd
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
During the initial phases, the development and validation teams have to
deal with both Consumer SKU and Lite SKU firmware. Having the support for
CSE Lite enabled by default in coreboot helps in integrating both the SKUs.
With this we only have to interchange the CSE region in the full BIOS image
without having to worry about Kconfigs. Eases the build and integration
flow.
TEST=Verified build for Shadowmountain
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I2ebf4da1b8c1df2e9c43b6e3bb688a9f8db652d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51496
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
During the initial phases, the development and validation teams have to
deal with both Consumer SKU and Lite SKU firmware. Having the support for
CSE Lite enabled by default in coreboot helps in integrating both the SKUs.
With this we only have to interchange the CSE region in the full BIOS image
without having to worry about Kconfigs. Eases the build and integration
flow.
TEST= Built and booted on ADL-P LP4 RVP
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ia92c7b71c69a23104ace9fc53fd39f01120fa751
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51567
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some tested modules require regions to be defined but do not necessarily
access them. TEST_REGION_UNALLOCATED() combined with DECLARE_REGION()
are sufficient for most cases that require symbols only.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I51c5f6ce56575021c6e4277a9ed17263cd2e3bb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51769
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This add an option to generate KM using the 9elements bg-prov tool
using a json config file.
The option to just include a provided KM binary is kept.
A template for the json config file can be obtained via
"bg-prov template".
Another option is to extract it from a working configuration:
"bg-prov read-config".
Change-Id: I18bbdd13047be634b8ee280a6b902096a65836e4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50409
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We use `additional-dirs` for a single `mkdir -p` invocation for all
directiories. I don't see why these two, $(objcbfs) and $(objgenerated),
should be an exception.
Fixes clean builds for targets that don't include the phony `coreboot`
target, e.g. `make qemu`.
Change-Id: I85abaa74cddefd2bd669e2b5c8934352775070fe
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch allows overriding GPIO PM miscconfig register for each
GPIO community to avoid dynamic clock gating.
TEST=Dump GPIO Community MISCCFG register to ensure all Bit [7:0]
are set to '0'.
Change-Id: I9aca9cb0641e2731c028ea5ed76c563da3400b74
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Lists of changes:
1. Rename MISCCFG_ENABLE_GPIO_PM_CONFIG -> MISCCFG_GPIO_PM_CONFIG_BITS
2. Move MISCCFG_GPIO_PM_CONFIG_BITS definition from intelblock/gpio.h to
soc/gpio.h. Refer to detailed description below to understand the
motivation behind this change.
An advanced GPIO PM capabilities has been introduced since CNP PCH,
refer to 'include/intelblock/gpio.h' for detailed GPIO PM bit definitions.
Now with TGP PCH, additional bits are defined in the MISCCFG register
for GPIO PM control. This results in different SoCs supporting
different number of bits. The bits defined in earlier platforms
(CNL, CML, ICL) are present on TGL, JSL and ADL too. Hence, refactor the
common GPIO code to keep the bit definitions in intelblock/gpio.h, but
the definition of MISCCFG_GPIO_PM_CONFIG_BITS is moved to soc/gpio.h so
that each SoC can provide this as per hardware support.
TEST=On ADL, TGL and JSL platform.
Without this CL :
GPIO COMM 0 MISCCFG:0xC0 (Bit 6 and 7 enable)
With this CL :
GPIO COMM 0 MISCCFG: 0x00 (Bit 6 and 7 disable)
Change-Id: Ie027cbd7b99b39752941384339a34f8995c10c94
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
List of changes:
1. Update GPIO Group to GPE DWx assignment encoding as per MISCCFG
register per GPIO Community.
2. PMC_GPP_* macros are also updated as per GPIO_CFG register
in PMC space.
BUG=b:183464235
TEST=Able to fix the TPM IRQ issue on SM.
Change-Id: Id9f57b0b5726315f5ebba013f11d52ed3ee34484
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51789
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, we used to stitch extra VBT files to ADLRVP build using
Makefile. With enablement of emerge build, we should be able to
integrate more than 1 VBT binaries using ebuild.
This removing these lines to avoid compilation issues in emerge builds
BUG=None
BRANCH=None
TEST=Check if compilation passes on emerge build. Stitched additional
VBT files using emerge and checked that coreboot picks up correct VBT.
Change-Id: I69f1cc6c07415515ff85180fdd7cc5de11b4d805
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This patch adds a bit of a "preamble" to the coding style to provide
guideance on how it should be applied and how style questions that
aren't mentioned should be handled.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I88efd5f1006bd1fd82cea14ea65422d9958dc197
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add function to allow overriding the RcompResistor and
RcompTarget UPDs from mainboard if required.
Mainboard users can pass required rcomp from memory.c file.
Refactor ddr_config structure to take out rcomp related variable
outside for all memory type to override if required.
BUG=b:182772421
TEST=Able to override the default RcompResistor and RcompTarget
values.
Change-Id: Ie8528bbf0517728534d47f9adaabfc9a2c469609
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
List of changes:
1. Alder Lake MRC is expecting a RcompResistor value of word width.
Reference RCOMP resistors on motherboard are ~ 100 Ohms but coreboot
is passing an array of RcompResistor which is not completely in use.
Note: Rcomp resistor value represents rcomp resistor attached to
the DDR_COMP pins on the SoC.
2. Also, remove usage of '&' with memcpy the required value into
RcompTarget array.
3. Also, update RcompResistor value for ADLRVP.
BUG=b:183341229
TEST=Enable FSP debug log to verify the override value for
RcompResistor is reflecting correctly.
Change-Id: I69c7cec55b65036fc039c33374a3fd363ef7004e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set default USB2 HS disconnect threshold to maximum to avoid false
disconnects that eventually lock up the xHCI controller
BUG=b:174538960
TEST=suspend_stress_test -c 50 on vilboz and morphius.
Sample set of USB2 HS devices connect and disconnect
successfully
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: Ic921d850a0bdd717a2a7e50e9e6f65e39e0607bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51265
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
commit 4f87ae1d4a introduced a regression
in the I2C initialization resulting in soc_i2c_misc_init never getting
called, since the continue statement was indented like it belonged to
the if above, but due to the missing curly braces it was outside the if
block.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Found-by: Coverity CID 1451395, 1451387
Change-Id: Id1f17ad59cba44e96881f5511df303ae90841ab3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51786
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The previous "PCIe port" numbering was incorrect and resulted in several
PCIe devices failing to enumerate. With lane reversal, these numbers are
all backwards. This explains the confusing mapping of Clock Source #1 to
Root Port #9 in https://review.coreboot.org/c/coreboot/+/50101. We were
confusing "Root Port" vs "PCIe Lane".
This change addresses the port vs. lane confusion in the device tree
configurations. It also adds more detailed documentation to a future
reader (i.e., me) to avoid this blunder.
BUG=b:181633452,b:181635072,b:177752570
TEST=build AP firmware; flash device
BRANCH=none
Change-Id: I47edf0b0af1bdcf86b89f17ad2a1f128ef9e9f7a
Signed-off-by: Joe Tessler <jrt@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
After revisiting the genesis GPIO table and schematics for EVT closure,
I discovered several missing and/or incorrectly documented GPIO pin
mappings.
Now the GPIO pin names and functions should match what's written in the
latest schematics.
BUG=b:181633452,b:181635072,b:177752570
TEST=build AP firmware; flash device
BRANCH=none
Change-Id: I73e6733bce761b00717091834c7a49e85154f80b
Signed-off-by: Joe Tessler <jrt@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51677
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both EHCI and xHCI USB controllers are inside the PCH (southbridge).
Now that mainboard USB configuration no longer depends on pei_data.h
definitions, the API declarations can be placed in southbridge code.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: Ia21991b225482b33c5bc0dc52884674d301b28ba
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
With this change, only raminit.c uses pei_data.h definitions. With MRC
cornered, making it optional is just a matter of writing a replacement.
USB config definitions will be moved to Lynx Point code in a follow-up.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: I4bc405213e9b0828d9ced18677335533c7dd381d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add memory table to "mem_list_variant.txt", and command to generate files:
go run ./util/spd_tools/lp4x/gen_part_id.go src/soc/intel/tigerlake/spd src/mainboard/google/volteer/variants/collis/memory/ src/mainboard/google/volteer/variants/collis/memory/mem_list_variant.txt
DRAM Part Name ID to assign
MT53D512M64D4NW-046 WT:F 0 (0000)
H9HCNNNCRMBLPR-NEE 0 (0000)
MT53D1G64D4NW-046 WT:A 1 (0001)
H9HCNNNFBMBLPR-NEE 2 (0010)
BUG=b:182227204
TEST=emerge-volteer coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I773c65c0b6d5e868572530305ab8a61a0dd1532d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Follow schematic to modify USB port settings.
USB2 [0]: USB Type C Port 0
USB2 [1]: None
USB2 [2]: USB Type A Port 0
USB2 [3]: LTE
USB2 [4]: None
USB2 [5]: Camera UFC
USB2 [6]: Camera WFC
USB2 [7]: Integrated Bluetooth
USB3 [0]: USB Type C Port 0 (M/B side)
USB3 [1]: None
USB3 [2]: USB Type A Port 0 (M/B side)
USB3 [3]: LTE
BUG=b:182973703
BRANCH=dedede
TEST=Build the coreboot image.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I80447d6ac3422f858a9022f550b4f42353819405
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The 'device pci 00.0 on end' entries are not necessary for socketed
devices unless a chip driver needs to be bound to a device, so remove
them from the devicetree. Also remove the `drivers/wifi/generic` chip
driver as it was not necessary either.
Change-Id: Id5f2e34d98b236f9cfac9f0afd8a8017e349603f
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The timeout is never reached when the codec is functioning properly.
Using a small timeout value can result in spurious errors with some
codecs, e.g. a codec that is slow to respond but operates correctly.
When a codec is non-operative, the timeout is only reached once per
verb table, thus the impact on booting time is relatively small. So,
use a reasonably long enough timeout to cover all possible cases.
Remove the unconditional 25 µs delay and increase the timeout delay.
The new value of 1 ms is the maximum of all existing implementations.
Currently, the only boards using this code are AMD reference boards:
- AMD Bilby
- AMD Mandolin
- AMD Padmelon
Change-Id: Ia5e4829d404dcecdb9e7a377e896a319cb38531a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested with TianoCore payload (UefiPayloadPkg).
Working:
- PS/2 keyboard, touchpad
- Both DIMM slots
- Both NVMe ports
- SATA port
- All USB ports
- Webcam
- Ethernet
- Integrated graphics using Intel GOP driver
- Internal microphone
- Internal speakers
- S3 suspend/resume
- Flashing with flashrom
- Booting to Ubuntu Linux 20.10 and Windows 10
Not working:
- Discrete/Hybrid graphics
This requires a new driver to work correctly, which will be added and
enabled later.
Change-Id: I10667fa26ac7c4b8eb67da11f3e963062bd0db47
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47822
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the MRC cache API for asurada, and sync dramc_param.h with dram
blob (CL:*3674585). With this change, the checksum, originally stored in
flash, is replaced with a hash in TPM. In addition, in recovery boot,
full calibration will always ne performed, and the cached calibration
data will be cleared from flash.
This change increases ROMSTAGE size from 236K to 264K. Most of the
increase is caused by TPM-related functions.
Add new API mtk_dram_init() to emi.h, so that 'dramc_parameter' can be
moved to soc folder.
With this CL, there is no significant change in boot time. Normal AP
reboot time (fast calibration) is consistently 0.98s as before, so
this change should not affect the result of platform_BootPerf.
BUG=b:170687062
TEST=emerge-asurada coreboot
TEST=Hayato boots with both full and fast calibration
BRANCH=none
Cq-Depend: chrome-internal:3674585, chrome-internal:3704751
Change-Id: Ief942048ce530433a57e8205d3a68ad56235b427
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Enlarge ROMSTAGE from 256K to 272K for the upcoming change of MRC cache
(CB:51620). To have more compact space usage, reduce BOOTBLOCK size from
64K to 60K (only 44K needed), and move starting address of DRAM blob
(DRAM_INIT_CODE) to 0x210000 (64K-aligned).
BUG=b:170687062
TEST=emerge-asurada coreboot
TEST=Hayato boots
BRANCH=asurada
Cq-Depend: chrome-internal:3704751
Change-Id: I7aaf9faf048e0adcb3a7d856d40891762c9a6604
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51730
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The headers added are generated as per FSP v2081_02.
Previous FSP version was v2081_02.
Changes Include:
- Adjust UPD Offset in FspmUpd.h and FspsUpd.h
- Add UPDs in Fsps.h and Fspm.h
BUG=b:180918805
BRANCH=None
TEST=Build and boot ADLRVP
Change-Id: I69611de8286a570c59a6b4a44b9164384e9be81f
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51632
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This makes the EM100 option visible in Kconfig that makes sure that the
SPI settings that coreboot applies are valid for the EM100 that has some
limitations on the maximum SPI frequency and possibly on the supported
SPI modes. For the PSP SPI settings, the mainboard still might need to
provide EM100-specific settings for EFS_SPI_READ_MODE, EFS_SPI_SPEED and
EFS_SPI_MICRON_FLAG. Haven't checked if those PSP settings are correctly
integrated for Cezanne.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5dec9ce69628ca3623b5009d47f4b3dc020a3dad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
There are at most 14 USB2 ports and 6 USB3 ports on LynxPoint-H, and
there are at most 10 USB2 ports and 4 USB3 ports on LynxPoint-LP. Limit
the array lengths accordingly to cause build errors on invalid configs.
Change-Id: Ieda7a1320d78dbbcb651f1715a87cd1d202a79f2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51451
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's common to use the raw, unshifted I2C address in coreboot. Adapt
mainboards accordingly and perform the shift in MRC glue code.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: I4e4978772744ea27f4c5a88def60a8ded66520e1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51458
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reorganize romstage.c to resemble sandybridge, and move everything that
needs `pei_data` into raminit.c function `perform_raminit`. Barring USB
settings, coreboot code no longer depends on pei_data.h definitions. It
still depends on MRC, though. For now.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: I433f88db5fe7a7533ab6837015647ec31fb45e88
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51449
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
eDP panel flicker during system idle state is observed.
Disabling USB2 SUS well power gating can remove flicker symptom.
Please refer to doc#634894 for more details.
BUG=b:182323059
BRANCH=None
TEST=Boot and confirm no display flicker.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: Icadf9c494fab82b219317c3ca3b04f633b543083
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add SPD support to eldrid for DDR4 memory part H4AAG165WB-BCWE.
Eldrid should use DRAM_ID strap ID 4 (0100) on SKUs populated
with H4AAG165WB-BCWE DDR4 memory parts.
BUG=b:181732562
TEST="FW_NAME=eldrid emerge-volteer coreboot" and verify it builds
successfully.
Change-Id: I38cfe3eb26b00563ce17df3a3ac2a0a846f2ae00
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51667
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the cret variant of the waddledoo reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:181325655
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CRET
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I700201cf81b25c6776df3ec9fc843cd9bd8c88c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
When the soc_get_mbox_address functions returns 0 after not being able
to find an initialized PSP base address MSR or in case of Stoneyridge
the PSP's BAR3, the code will print an error string. This string needs
to reference both PSP_ADDR_MSR and PSP BAR3 and not only the latter one,
since in Picasso and Cezanne only the former one is present.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I32a1e87e2a7d89c7b53f47c987e7bf0556154cf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Lynx Point reference code version 1.9.1 and soc/intel/common/hda_verb.c
perform these steps. Add them to Lynx Point as well. With this change,
Lynx Point and soc/intel/common hda_verb.c files are now identical.
Change-Id: I2fc592f73697a43bd5a3315ac80c77ff9f00da9b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch is trying to address some of the concerns raised in CB:50247
after the patch had landed. The preference for alphabetized headers was
just supposed to discourage leaving headers completely unordered, and
wasn't intended to disallow other intentional include orderings such as
grouping local includes after system ones or specific ordering
constraints that exist for technical reasons. This patch adds a few more
sentences to try to clarify that.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I6825f4a57613fabb88a00ae46679b4774ef7110b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Do not use the same name as the non-LP GPIO config. This allows checking
at build-time that a mainboard uses the correct GPIO config format.
Without this commit, there are no build-time errors when using the wrong
format of GPIO config, but there would be undefined behavior at runtime.
Tested by trying to build asrock/b85m_pro4 and hp/folio_9480m after
toggling the `INTEL_LYNXPOINT_LP` Kconfig option (and trimming down the
USB config arrays for asrock/b85m_pro4). In both cases, building failed
because the necessary GPIO config global is not defined, as expected.
Change-Id: Ib06507ef8179da22bdb27593daf972e788051f3a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51661
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use timer.h helpers instead of open-coding timeout handling in polling
loops. The 25-microsecond delay in `wait_for_valid` looks odd, and may
be removed in subsequent commits. For now, preserve existing behavior.
Change-Id: Id1227c6812618597c37408a7bf53bcbcae97374a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50789
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Until now every AML package had to be closed using acpigen_pop_len().
This commit introduces set of package closing functions corresponding
with their opening function names. For example acpigen_write_if()
opens if-statement package, acpigen_write_if_end() closes it.
Now acpigen_write_else() closes previously opened acpigen_write_if(),
so acpigen_pop_len() is not required before it.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Icfdc3804cd93bde049cd11dec98758b3a639eafd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add I2C initialization in romstage and ramstage.
TEST=To test the I2C connection on Majolica, which doesn't have SPD
connection, call the function below after i2c_soc_init is called.
i2c_read_bytes(2, 0x4d, addr, data, 1);/* Read out 1 byte one time */
It can get the register values of TMP432B.
Or
/* Override EC port in ec.h */
#define EC_DATA 0x662
#define EC_SC 0x666
ec_write(0xA9, 0x40);
i2c_read_bytes(1, 0x10, addr, data, 2);/* Read out 2 bytes one time */
It can get the register values of CM32181A3OP(ALS).
Change-Id: I3a2a1494b44b68e8d8204fba0c90e769e0256e6f
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51029
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The logic behind I2C bus initialization, I2C MMIO base address getter
and setter, I2C bus ACPI name resolution are identical for all the AMD
SoCs. Hence moving all the SoC agnotic parts of the driver into the
common driver and just configure the SoC specific parts into individual
I2C drivers.
BUG=None
TEST=Build Dalboz and Grunt. Boot to OS in Dalboz. Ensure that the I2C
peripherals are detected as earlier in Dalboz. Verify some I2C
peripheral functionality like trackpad and touchscreen.
Change-Id: Ic9c99ec769d7d8ad7e1e566fdf42a5206657183d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Suggested-by: Kyosti Malkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51509
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I2C driver is replicated in each generation of AMD SoCs. Introduce a
common I2C driver that can be used across all the AMD SoCs. To begin
with, peripheral reset functionality is moved into this common driver.
SoC specific I2C driver passes the SCL pin configuration in order for
the common driver to reset the peripherals. More functionality can be
moved here in subsequent changes.
Also sb_reset_i2c_slaves() is renamed as sb_reset_i2c_peripherals() as
an effort towards using inclusive language.
BUG=None
TEST=Build Dalboz and Grunt. Boot to OS in Dalboz. Ensure that the I2C
peripherals are detected as earlier in Dalboz.
localhost ~ # i2cdetect -y 0
Warning: Can't use SMBus Quick Write command, will skip some addresses
0 1 2 3 4 5 6 7 8 9 a b c d e f
00:
10:
20:
30: -- -- -- -- -- -- -- --
40:
50: 50 51 -- -- -- -- -- -- 58 59 -- -- -- -- -- --
60:
70:
localhost ~ # i2cdetect -y 1
Warning: Can't use SMBus Quick Write command, will skip some addresses
0 1 2 3 4 5 6 7 8 9 a b c d e f
00:
10:
20:
30: -- -- -- -- -- -- -- --
40:
50: UU -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60:
70:
Change-Id: I9f735dcfe8375abdc88ff06e8c4f8a6b741bc085
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Suggested-by: Kyosti Malkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The X200 would undock itself when waking up from S3, requiring a
physical reconnection before the dock would work again.
Similar to 4611ad8, this reintroduces h8_mb_init() for the X200. A hook
function h8_mb_init() will be called at the end of h8_enable(), in place
of the ancient h8_mainboard_init_dock().
This should fix the regression the X201 and T410 also suffered from for
the X200.
Change-Id: Icb6dd145e56b90e0e04133810c5e9ac7b641ad68
Signed-off-by: Kevin Keijzer <kevin@quietlife.nl>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51123
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit c4aa24fc12 (doc/mb/lenovo/montevina: Clarify use of bincfg)
renamed a section, and the link referencing it by its old title no
longer works. Update the link, and remove the `a completely new one`
part from it as well, for consistency with the aforementioned commit.
Change-Id: I22e8b3237dafb3397bc901804a57e905f806839d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51482
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This will not enable M.2 SATA drive if the ME config was lost
(For instance after flashing a full flash factory image)
This is required so that the system can boot without FIA MUX error
during flash update procedure.
Change-Id: I55a8bcdc30bc67af2d3e9ccb8844eac599727108
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/25443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Make sure the bytes in RTC cmos used by CBNT don't collide with the
option table. This depends on what is set up in the BPM, Boot Policy
Manifest. When the BPM is provided as a binary the Kconfig needs to be
adapted accordingly. A later patch will use this when generating the
BPM.
Change-Id: I246ada8a64ad5f831705a4293d87ab7adc5ef3aa
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Global variables are located in .bss and not on the CPU stack.
Overwriting them a per CPU case is bound to cause race conditions. In
this case it is even just plainly wrong.
Note: This variable is set up in the get_smm_info() function.
Change-Id: Iaef26fa996f7e30b6e4c4941683026b8a29a5fd1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The permanent handler module argument 'save_state_size' now holds the
meaning of the real save state size which is then substracted from the
CPUs save state 'top' to get the save state base.
TESTED with qemu Q35 on x86_64 where the stub size exceeds the AMD64
save state size.
Change-Id: I55d7611a17b6d0a39aee1c56318539232a9bb781
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
With the smm_module_loaderv2 the save state map is not linear so copy
a map from ramstage into the smihandler.
TESTED on QEMU q35: Both SMMLOADER V1 and V2 handle save states properly.
Change-Id: I31c57b59559ad4ee98500d83969424e5345881ee
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Move out smm_create_map as this was not run if concurrent_save_states
is 1. The cpus struct array is used in the smm_get_cpu_smbase()
callback so it is necessary to create this.
TEST: run qemu/q35 with -smp 1 (or no -smp argument)
Change-Id: I07a98bbc9ff6dce548171ee6cd0c303db94087aa
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50783
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The parameters that the permanent handler requires are pushed directly
to the permanent handlers relocatable module params.
The paremeters that the relocation handler requires are not passed on
via arguments but are copied inside the ramstage. This is ok as the
relocation handler calls into ramstage.
Change-Id: Ice311d05e2eb0e95122312511d83683d7f0dee58
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
struct smm_loader_params is a struct that is passed around in the
ramstage code to set up either the relocation handler or the permanent
handler. At the moment no parameters in the stub 'smm_runtime' are
referenced so it can be dropped. The purpose is to drop the
smm_runtime struct from the stub as it is already located in the
permanent handler.
Change-Id: I09c1b649b5991f55b5ccf57f22e4a3ad4c9e4f03
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Instead of passing on parameters from the stub to the permanent
handler, add them directly to the permanent handler.
The parameters in the stub will be removed in a later patch.
Change-Id: Ib3bde78dd9e0c02dd1d86e03665fa9c65e3d07eb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
With CBnT a digest needs to be made of the IBB, Initial BootBlock, in
this case the bootblock. After that a pointer to the BPM, Boot Policy
Manifest, containing the IBB digest needs to be added to the FIT
table.
If the fit table is inside the IBB, updating it with a pointer to the
BPM, would make the digest invalid.
The proper solution is to move the FIT table out of the bootblock.
The FIT table itself does not need to be covered by the digest as it
just contains pointers to structures that can by verified by the
hardware itself, such as microcode and ACMs (Authenticated Code
Modules).
Change-Id: I352e11d5f7717147a877be16a87e9ae35ae14856
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50926
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The purpose of this is to eventually move the FIT table out of the
bootblock, generate it separately as a cbfs file and then have the FIT
pointer point to that cbfs file.
TESTED: extracted a FIT table using dd, added it as a cbfs file and see
that the FIT pointer correctly points to it. Also test that trying to
add a non valid FIT cbfs file results in an error.
Change-Id: I6e38b7df31e6b30f75b0ae57a5332f386e00f16b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
elemi does not use the GPP_B7/GPP_B8, so config to NC.
Currently, there is no functional impact.
BUG=b:182981460
TEST=emerge-volteer coreboot, boot into OS, and suspend/resume
successfully.
Change-Id: I7b491fd595b0e77e6dcce08e3172dbe592f63c37
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Mainboards do not need to know about `pei_data` to tell northbridge code
where to find the SPD data. Adjust `mb_get_spd_map` to take a pointer to
a struct instead of an array, and update all the mainboards accordingly.
Currently, the only board with memory-down in the tree is google/slippy.
Mainboard code now obtains the SPD index in `mb_get_spd_map` and adjusts
the channel population accordingly. Then, northbridge code reads the SPD
file and uses the index that was read in `mb_get_spd_map`, and copies it
to channel 0 slot 0 unconditionally. MRC only uses the first position of
the `spd_data` array, and ignores the other positions. In coreboot code,
`setup_sdram_meminfo` uses the data of each SPD index, so `copy_spd` has
to account for this.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: Ibaed5c6de9853db6abd08f53bbfda8800d207c3e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51448
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MRC only uses the SPD data for the first index, and ignores the rest.
Moreover, index 1 corresponds to the second DIMM on the first channel,
which does not exist on ULT (only one DIMM per channel is supported).
Copy the SPD to the first DIMM on channel 1 instead. Adjust northbridge
code to retrieve the serial number from the correct SPD data block.
Tested on Google Wolf, both channels are still correctly detected.
Change-Id: Ic60ff75043e6b96a59baa9e5ebffb712a100a934
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The SLP_S0_GATE# signal is used in conjunction with the PCH's SLP_S0# to
provide an indication to the rest of the platform when the system is
entering its software-initiated low-power state (i.e. S0ix). This lets
the platform distinguish between opportunistic S0ix entry and the runtime
suspend mechanism.
BUG=b:180401723
TEST=abuild
Change-Id: I7fe2e3707465778baf56283617a8485a94f2dbca
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50881
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When running coreboot unit tests on a recent clang version, it helpfully
throws an error on memset(..., 0xAA, 0) because it thinks you probably
made a typo and meant to write memset(..., 0, 0xAA) instead. I mean, who
would ever memset() a buffer of zero bytes, right? Unfortunately, unit
tests for memset() want to do exactly that. Wrapping the argument in
parenthesis silences the warning.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I21aeb5ec4d6ce74d5df2d21e2f9084b17b3ac6e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Don't use 'is' and 'is not' for comparison with literals. This fixes
warnings like:
.../mbn_tools.py:1097: SyntaxWarning: "is not" with a literal. Did you mean "!="?
if int(off) is not 0:
Change-Id: Idd68acfcbd1a07cbbb9ab41d9581c4850a431445
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The data needed to compute the permanent smbase for a core, when
relocating, is present in the ramstage data which the stub located at
DEFAULT_SMBASE (0x30000) calls back to. There is no need to fetch this
from via the stub params.
Change-Id: I3894c39ec8cae3ecc46b469a0fdddcad2a8f26c4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50763
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These stub params need to be synced with the code in smm_stub.S and
are consumed by both the smmloader and smmloader_v2. So it is better
to have the definition located in one place.
Change-Id: Ide3e0cb6dea3359fa9ae660eab627499832817c9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50761
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We are currently writing invalid ACPI tables. We are missing the GPP
ACPI names. There is an assert in acpi_device_write_pci_dev that checks
to see if we have a scope, but by default asserts don't halt, so we were
writing a NULL scope.
BUG=b:171234996
TEST=Boot majolica and dump ACPI tables
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6a861ad1b9259ac3b79af76e18a9354997b0491e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
In pursuit of the goal of eliminating the proliferation of raw region
devices to represent CBFS files outside of the CBFS core code, this
patch removes the get_spd_cbfs_rdev() API and instead replaces it with
spd_cbfs_map() which will find and map the SPD file in one go and return
a pointer to the relevant section. (This makes it impossible to unmap
the mapping again, which all but one of the users didn't bother to do
anyway since the API is only used on platforms with memory-mapped
flash. Presumably this will stay that way in the future so this is not
something worth worrying about.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Iec7571bec809f2f0712e7a97b4c853b8b40702d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch rewrites some parts of the Agesa refcode loader to eliminate
the passing of raw rdevs between functions, so that we can get rid of
cbfs_boot_locate() in favor of more high-level APIs.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I2a6e1158ed7425c69c214462bc52e8694a69997a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In pursuit of the eventual goal of removing cbfs_boot_locate() (and
direct rdev access) from CBFS APIs, this patch replaces all remaining
"simple" uses of the function call that can easily be replaced by the
newer APIs (like cbfs_load() or cbfs_map()). Some cases of
cbfs_boot_locate() remain that will be more complicated to solve.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Icd0f21e2fa49c7cc834523578b7b45b5482cb1a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The CBFS stage header is part of the file data (not the header) from
CBFS's point of view, which is problematic for verification: in pre-RAM
environments, there's usually not enough scratch space in CBFS_CACHE to
load the full stage into memory, so it must be directly loaded into its
final destination. However, that destination is decided from reading the
stage header. There's no way we can verify the stage header without
loading the whole file and we can't load the file without trusting the
information in the stage header.
To solve this problem, this patch changes the CBFS stage format to move
the stage header out of the file contents and into a separate CBFS
attribute. Attributes are part of the metadata, so they have already
been verified before the file is loaded.
Since CBFS stages are generally only meant to be used by coreboot itself
and the coreboot build system builds cbfstool and all stages together in
one go, maintaining backwards-compatibility should not be necessary. An
older version of coreboot will build the old version of cbfstool and a
newer version of coreboot will build the new version of cbfstool before
using it to add stages to the final image, thus cbfstool and coreboot's
stage loader should stay in sync. This only causes problems when someone
stashes away a copy of cbfstool somewhere and later uses it to try to
extract stages from a coreboot image built from a different revision...
a debugging use-case that is hopefully rare enough that affected users
can manually deal with finding a matching version of cbfstool.
The SELF (payload) format, on the other hand, is designed to be used for
binaries outside of coreboot that may use independent build systems and
are more likely to be added with a potentially stale copy of cbfstool,
so it would be more problematic to make a similar change for SELFs. It
is not necessary for verification either, since they're usually only
used in post-RAM environments and selfload() already maps SELFs to
CBFS_CACHE before loading them to their final destination anyway (so
they can be hashed at that time).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I8471ad7494b07599e24e82b81e507fcafbad808a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since prog_locate() was eliminated, prog_rdev() only ever represents the
loaded program in memory now. Using the rdev API for this is unnecessary
if we know that the "device" is always just memory. This patch changes
it to be represented by a simple pointer and size. Since some code still
really wants this to be an rdev, introduce a prog_chain_rdev() helper to
translate back to that if necessary.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If7c0f1c5698fa0c326e23c553ea0fe928b25d202
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
IPMI OEM command set processor information has already been implemented
in u-root payload:
efdc3a30ec
Also this command has a higher chance to see BMC KCS timeout issue when
coreboot log level is 4, which can be avoided if this command is run at
a later stage such as LinuxBoot.
Signed-off-by: JingleHsuWiwynn <jingle_hsu@wiwynn.com>
Change-Id: If0081e5195cbd605e062723c197ac74343f79a13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51276
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates the release notes for coreboot-4.14 to add
deprecation notice for SAR support in VPD for Chrome OS platforms.
BUG=b:173465272
Change-Id: If6d511a22a3a2a31671dac91e57e801134d4ecf8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51486
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, if `get_wifi_sar_cbfs_filename()` returns NULL, then
`get_wifi_sar_limits()` assumes that the default filename is used for
CBFS SAR file. This prevents a board from supporting different models
using the same firmware -- some which require SAR support and some
which don't.
This change updates the logic in `get_wifi_sar_limits()` to return
early if filename is not provided by the mainboard. In order to
maintain the same logic as before, current mainboards are updated to
return WIFI_SAR_CBFS_DEFAULT_FILENAME instead of NULL in default
case.
Change-Id: I68b5bdd213767a3cd81fe41ace66540acd68e26a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51485
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that SAR support in VPD is deprecated in coreboot, there is no
need for a separate Kconfig `WIFI_SAR_CBFS` as the SAR table is only
supported as a CBFS file. This change drops the config `WIFI_SAR_CBFS`
from drivers/wifi/generic/Kconfig and its selection in
mb/google/.../Kconfig.
wifi_sar_defaults.hex is added to CBFS only if
CONFIG_WIFI_SAR_CBFS_FILEPATH is not empty because current mainboards
do not provide a default SAR file in
coreboot. Thus, CONFIG_WIFI_SAR_CBFS_FILEPATH is updated to have a
default value of "".
BUG=b:173465272
Cq-Depend: chromium:2757781
Change-Id: I0bb8f6e2511596e4503fe4d8c34439228ceaa3c7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
SAR table in VPD has been deprecated for Chrome OS platforms for > 1
year now. All new Chrome OS platforms have switched to using SAR
tables from CBFS.
This change drops the support for SAR table in VPD from coreboot to
align with the factory changes. `get_wifi_sar_limits()` is thus
updated to look for SAR file in CBFS only.
Anyone building ToT coreboot for an already released Chrome OS
platform with SAR table in VPD will have to extract the "wifi_sar" key
from VPD and add it as a file to CBFS using following steps:
- On DUT, read SAR value using `vpd -i RO_VPD -g wifi_sar`
- In coreboot repo, generate CBFS SAR file using:
`echo ${SAR_STRING} > site-local/${BOARD}-sar.hex`
- Add to site-local/Kconfig:
```
config WIFI_SAR_CBFS_FILEPATH
string
default "site-local/${BOARD}-sar.hex"
```
BUG=b:173465272
Change-Id: I21d190dcc9f3554fab6e21b4498e7588a32bb1f0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch rewrites the last few users of prog_locate() to access CBFS
APIs directly and removes the call. This eliminates the double-meaning
of prog_rdev() (referring to both the boot medium where the program is
stored before loading, and the memory area where it is loaded after) and
makes sure that programs are always located and loaded in a single
operation. This makes CBFS verification easier to implement and secure
because it avoids leaking a raw rdev of unverified data outside the CBFS
core code.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I7a5525f66e1d5f3a632e8f6f0ed9e116e3cebfcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch removes the prog_locate() step for stages and rmodules.
Instead, the stage and rmodule loading functions will now perform the
locate step directly together with the actual loading. The long-term
goal of this is to eliminate prog_locate() (and the rdev member in
struct prog that it fills) completely in order to make CBFS verification
code safer and its security guarantees easier to follow. prog_locate()
is the main remaining use case where a raw rdev of CBFS file data
"leaks" out of cbfs.c into other code, and that other code needs to
manually make sure that the contents of the rdev get verified during
loading. By eliminating this step and moving all code that directly
deals with file data into cbfs.c, we can concentrate the code that needs
to worry about file data hashing (and needs access to cbfs_private.h
APIs) into one file, making it easier to keep track of and reason about.
This patch is the first step of this move, later patches will do the
same for SELFs and other program types.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ia600e55f77c2549a00e2606f09befc1f92594a3a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49335
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The --alignment flag is currently only handled by cbfstool add, but
there seems little reason to not handle it for all file-adding commands
(the help text actually mentions it for add-stage as well but it doesn't
currently work there). This patch moves the related code (and the
related baseaddress handling) into cbfs_add_component(). As a nice side
effect this allows us to rearrange cbfs_add_component() such that we can
conclusively determine whether we need a hash attribute before trying to
align the file, allowing that code to correctly infer the final header
size even when a hash attribute was implicitly added (for an image built
with CBFS verification enabled).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Idc6d68b2c7f30e5d136433adb3aec5a87053f992
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47823
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Originally, log macro names are too long, and they use
double parentheses style: ((...)), which causes compile
or runtime error easily.
Now, change them to single parenthesis mode (...), and
use shorter name.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I2959dc1ba0dd40a8fb954406072f31cf14c26667
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The i2c actiming with the default reg setting cannot meet spec,
so we need to set some regs.
1. adjust the ratio of SCL high and low level, to adjust "tLOW".
2. modify ext_conf reg to adjust "tSU,STO".
BUG=b:179000159
TEST=Test on asurada (MT8192), boot pass,
timing pass.
Signed-off-by: Daolong Zhu <jg_daolongzhu@mediatek.corp-partner.google.com>
Change-Id: Ifbe97edbc38972af5b782fb93342ee0616127dd8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51024
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id a2390f3c5:
2020-12-01 08:35:44 +0000 - (servo_v4/usb_pd_policy: Reject SNK->SRC power swap if CC_ALLOW_SRC not set)
to commit id 1e800ac83:
2021-03-01 22:59:54 +0000 - (docs: point md files in master to main/HEAD)
This brings in 188 new commits.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5c276d7839e0bdbf14ac56f16c231d75a6ea4c3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Configuring GPP_B7 as GPO_HIGH.
Sasuke doesn't have SAR sensor, GPP_B7 is routed to the LTE module
and is kept high so that the LTE module uses the default emission power.
BUG=b:180492044
BRANCH=firmware-dedede-13606.B
TEST="FW_NAME=sasuke emerge-dedede coreboot"
Change-Id: Ib38c649830db2291b3a2a771f5c884acf37dcbeb
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51049
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some of the temperature sensors defined in baseboard do not exist in
magolor. With the format the DPTF policies are defined in magolor, all
the entries from the baseboard are included and then the overrides
applied. This causes the non-existent DPTF devices to be exported in
the ACPI table and in turn OS reading invalid temperatures. Fix the
format for DPTF passive and critical policies.
BUG=None
BRANCH=dedede
TEST=Build and boot to OS in magolor. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I43f0b188e49e24657db055ce898ce159d499a22e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Some of the temperature sensors defined in baseboard do not exist in
madoo. With the format the DPTF policies are defined in madoo, all the
entries from the baseboard are included and then the overrides applied.
This causes the non-existent DPTF devices to be exported in the ACPI
table and in turn OS reading invalid temperatures. Fix the format for
DPTF passive and critical policies.
BUG=b:182513022
BRANCH=dedede
TEST=Build and boot to OS in madoo. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Idc5d0b357d61b9346b4d20ec8322b124c9655b4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Ben Kao <ben.kao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
The X11SSH-LN4F and X11SSH-F are very similiar. They both use the same
PCB and use the same Supermicro BIOS ID. The X11SSH-LN4F has 4 NICs in
difference to the X11SSH-F which only has 2 NICs. The two additional
NICs aren't populated on the X11SSH-F. Enable the PCIe root ports
connected to the two additional Intel NICs.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Change-Id: Id4e66be47ceef75905ba760b8d5a14284e130f63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Drop the 100ms delay in the _PS0 method because kernel already adds this
100ms. This change also drops polling TBT PCIe root ports Link Active
State because this scheme is not applicable for SW CM.
BUG=None
TEST=Built Alderlake coreboot image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I792d3c8ca4249ed74d4090ec1efba5a180429c75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51191
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable the PCIe RTD3 driver for WWAN device attached to PCIe Root
Port 4 and provide the reset GPIO / src clk pin.
BUG=none
TEST=Boot to OS, verify the link is in L2 state during S0ix.
Change-Id: I669e02bd02e3af878648a6f3cf4fbb4d06c9857f
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Remove the CNVi BT PCI config and add BT flag. There is no PCI host interface
in this version of CNVi.
TEST: BT is checked using 'lsusb -d 8087:0026' from OS to make sure BT is
enumerated.
Change-Id: I8de5615235f24e6169bf67dbbadb92e69437bc4e
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50899
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the CNVi BT PCI config and add BT flag. There is no PCI host interface
in this version of CNVi.
TEST: BT is checked using 'lsusb -d 8087:0026' from OS to make sure BT is
enumerated.
Change-Id: Ic700021d7a09be63ffc2715f31992257e2e893af
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50898
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the CNVi BT PCI config and add Bt flag.
There is no PCI host interface in this version of CNVi.
TEST: BT is checked using 'lsusb -d 8087:0026' from OS.
Change-Id: I7e8ca1bb6a57721a72478137612d7a9c391ca0b2
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
FSP has added the Cnvi BT Core enabling in addition to the existing
CnviMode. This change adds the flag at the soc config side (i.e.
soc_intel_tigerlake_config for devicetree). Also, there is no longer PCI host
interface for BT. Therefore, BT core should not use the pci port status to turn
on/off.
TEST: BT enumeration is checked using 'lsusb -d 8087:0026' from OS to make
sure BT is turned on.
Change-Id: I71c512fe884060e23ee26e7334c575c4c517b78d
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use VPD of "coreboot_uart_io" to select uart io if
OVERRIDE_UART_FOR_CONSOLE is selected.
Tested=On OCP Delta Lake, console messages correctly output to uart
port which is defined in VPD.
Signed-off-by: Bryant Ou <Bryant.Ou.Q@gmail.com>
Change-Id: I55a85d6f137ef1aba95466e7b094740b685bf9bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Create the collis variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:182227204
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_COLLIS
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ibcf8b59b38d02517cea0a3ee474ff82fc0a2a958
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Override SMBIOS type 2 board feature flags. For Delta Lake, board is
replaceable and is a hosting board.
Tested=Execute "dmidecode -t 2" to check info is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I4469360ec51369dbf8179b3cbac0519ead7f0382
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
This patch overrides the get_wifi_sar_cbfs_filename()
to return different sar table according to the sku id.
BUG=b:173465272
TEST=checked bios log and the correct sar table was loaded.
Change-Id: Ia30d760b1a029197d470818c73bfd2c00514652d
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update GPP_A10 and GPP_H17 configuration to meet LTE power sequence
specification.
- FCPO (GPP_A10) should not turned off during warm reset.
BUG=b:177177967
BRANCH=dedede
TEST=Verified LTE power signal waveforms during powering on and off
Change-Id: I469f9c94ebd6bf2b68a0edc74f229158d82d0ef8
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
I was bugged by spurious "Failed to enable LTR" messages for years.
Looking at the the current algorithm, it is flawed in multiple ways:
* It looks like the author didn't know they implemented a
recursive algorithm (pciexp_enable_ltr()) inside another
recursive algorithm (pciexp_scan_bridge()). Thus, at every
tree level, everything is run again for the whole sub-
tree.
* LTR is enabled no matter if `.set_ltr_max_latencies` is
implemented or not. Leaving the endpoints' LTR settings
at 0: They are told to always report zero tolerance.
In theory, depending on the root-complex implementation,
this may result in higher power consumption than without
LTR messages.
* `.set_ltr_max_latencies` is only considered for the direct
parent of a device. Thus, even with it implemented, an
endpoint below a (non-root) bridge may suffer from the 0
settings as described above.
* Due to the double-recursive nature, LTR is enabled starting
with the endpoints, then moving up the tree, while the PCIe
spec tells us to do it in the exact opposite order.
With the current implementation of pciexp_scan_bridge(), it is
hard to hook anything in that runs for each device from top to
bottom. So the proposed solution still adds some redundancy:
First, for every device that uses pciexp_scan_bus(), we enable
LTR if possible (see below). Then, when returning from the bus-
scanning recursion, we enable LTR for every device and configure
the maximum latencies (if supported). The latter runs again on
all bridges, because it's hard to know if pciexp_scan_bus() was
used for them.
When to enable LTR:
* For all devices that implement `.set_ltr_max_latencies`.
* For all devices below a bridge that has it enabled already.
Change-Id: I2c5b8658f1fc8cec15e8b0824464c6fc9bee7e0e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51328
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change select the Kconfig to pre-allocate the Intel-recommended bus
and memory resources per-PCIe TBT root port for the brya0 mainboard.
TEST=snippet from dmesg logs shows the correct resources being allocated:
PCI: 00:07.0 resource base 27fc00000 size 1c000000 align 20 gran 20 limit 29bbfffff flags 60181202 index 24
PCI: 00:07.0 resource base 83000000 size c200000 align 20 gran 20 limit 8f1fffff flags 60080202 index 20
PCI: 00:07.1 resource base 29bc00000 size 1c000000 align 20 gran 20 limit 2b7bfffff flags 60181202 index 24
PCI: 00:07.1 resource base a0000000 size c200000 align 20 gran 20 limit ac1fffff flags 60080202 index 20
PCI: 00:07.2 resource base 2b7c00000 size 1c000000 align 20 gran 20 limit 2d3bfffff flags 60181202 index 24
PCI: 00:07.2 resource base ac200000 size c200000 align 20 gran 20 limit b83fffff flags 60080202 index 20
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6b520ae50f19a730263de7918594718f3b4b1c1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51455
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Intel ADL BIOS specification #627270 recommends reserving the
following resources for each PCIe TBT root port:
- 42 buses
- 192 MiB Non-prefetchable memory
- 448 MiB Prefetchable memory
Add a mainboard Kconfig which will auto-select these recommended values,
in addition to PCIEXP_HOTPLUG.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Icdfa2688d69c2db0f98d0523d5aba42eec1824db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51460
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Done for consistency with other platforms. This also drops redundant S3
resume logging, as `southbridge_detect_s3_resume` already prints it.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: Id96c5aedad80702ebf343dd0a351fbd4e7b1c6c1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
MT8192 devapc supports remapping domains.
There may be different domain bit for different subsys.
For example, domain bit in INFRA is 4-bit, while in MMSYS,
domain bit is 2-bit. For INFRA master to access MM registers,
the domain bit will change from 4 to 2 and need to be remapped.
In this patch we have remapped:
1. TINYSYS (3-bit to 4-bit)
- domain 3 to domain 3
- others to domain 15
2. MMSYS slave (4-bit to 2-bit)
- domain X to domain X, for X = 0 ~ 3
- others to domain 0
Change-Id: Id10a4c0bdf141cc76a386159896c861d0dc302aa
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Move the initialization from bootblock to romstage for following reasons:
- Follow MT8183 initialization sequence.
- PMIC and RTC functions are only called after verstage.
- Reduce bootblock size.
- PMIC initialization setting is complex and may need to be changed by
an RW firmware update.
TEST=boot to kernel successfully
Change-Id: I3e4c3f918639590ffc73076450235771d06aae91
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xi Chen <xixi.chen@mediatek.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Updating from commit id 4fdfa1c:
2021-03-05 13:10:22 -0600 - (mb/amd/majolica: Update to use proper APCBs built for Majolica)
to commit id fc2d4e2:
2021-03-12 10:31:48 -0700 - (mb/google/guybrush: Add initial APCB)
This brings in 1 new commit.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I3003fdb8ba0bcfbc33452999c35a9a21775ecc10
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Currently, `check-fmap-16mib-crossing` compares the offset and end of
each SPI flash region to 16MiB to ensure that no region is placed
across this 16MiB boundary from the start of SPI flash. What really
needs to be checked is that the region isn't placed across the 16MiB
boundary from the end of BIOS region. Thus, current check works only
if the SPI flash is 32MiB under the assumption that the BIOS region
is mapped at the top of SPI flash. However, this check will not work
if a flash part greater than 32MiB is used.
This change replaces the hardcoded boundary value of 16MiB with a
value calculated by subtracting 16MiB from the SPI flash size (if it
is greater than 16MiB). This calculated value is used as the boundary
that no region defined in the flashmap should be placed across.
The assumption here is that BIOS region is always placed at the top of
SPI flash. Hence, the standard decode window would be from
end_of_flash - 16M to end_of_flash (because end_of_flash =
end_of_bios_region). Currently, there is no consistency in the name
used for BIOS region in flashmap layout for boards in
coreboot. But all Intel-based boards (except APL and GLK) place BIOS
region at the end of SPI flash. Since APL and GLK do not support the
extended window, this check does not matter for these platforms.
Change-Id: Icff83e5bffacfd443c1c3fbc101675c4a6f75e24
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51359
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Perform some cosmetical changes:
* Override the first prerequisite so we can use `$<`.
* Add/remove whitspace to align things (recipe needs to be indented
by a single tab only).
* We can use shell variables inside double quotes. To make the
end of the variable name clear, use braces, e.g. "${x}".
NB. Most of the double quotes are unnecessary. They only change
the way the script would be failing in case of spurious whitespace.
* Break some lines doing multiple things at once.
* To reduce remaining clutter, put reading numbers into a shell
function.
And functional changes:
* No need to spawn `cat`, the shell can redirect input as well as
output (using `<`).
* To read a number from the `fmap_config.h`, we spawned 4 processes
where a single one can achieve the same. With one exception: GNU
awk refuses to parse hex numbers by default. Luckily, it turned
out that we don't need intermediate decimal numbers: Shells can
do arithmetic with hex values as well.
Change-Id: Ia7bfba0d7864fc091ee6003e09b705fd7254e99b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently, if everything worked fine, `$fail` will be unset, leading
to the following `if` statement:
if [ -eq 1 ]
Resulting in the error message:
/bin/sh: line 9: [: -eq: unary operator expected
Fix this by removing the whole `if`, we can just use `exit`.
Change-Id: I1bc7508d2a45a2bec07ef46b9c5d9d0b740fbc74
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
To support the new CONFIG_CBFS_VERIFICATION feature, cbfstool needs to
update the metadata hash embedded in the bootblock code every time it
adds or removes a CBFS file. This can lead to problems on certain
platforms where the bootblock needs to be specially wrapped in some
platform-specific data structure so that the platform's masked ROM can
recognize it. If that data structure contains any form of hash or
signature of the bootblock code that is checked on every boot, it will
no longer match if cbfstool modifies it after the fact.
In general, we should always try to disable these kinds of features
where possible (they're not super useful anyway). But for platforms
where the hardware simply doesn't allow that, this patch introduces the
concept of "platform fixups" to cbfstool. Whenever cbfstool finds a
metadata hash anchor in a CBFS image, it will run all built-in "fixup
probe" functions on that bootblock to check if it can recognize it as
the wrapper format for a platform known to have such an issue. If so, it
will register a corresponding fixup function that will run whenever it
tries to write back modified data to that bootblock. The function can
then modify any platform-specific headers as necessary.
As first supported platform, this patch adds a fixup for Qualcomm
platforms (specifically the header format used by sc7180), which
recalculates the bootblock body hash originally added by
util/qualcomm/createxbl.py.
(Note that this feature is not intended to support platform-specific
signature schemes like BootGuard directly in cbfstool. For anything that
requires an actual secret key, it should be okay if the user needs to
run a platform-specific signing tool on the final CBFS image before
flashing. This feature is intended for the normal unsigned case (which
on some platforms may be implemented as signing with a well-known key)
so that on a board that is not "locked down" in any way the normal use
case of manipulating an image with cbfstool and then directly flashing
the output file stays working with CONFIG_CBFS_VERIFICATION.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I02a83a40f1d0009e6f9561ae5d2d9f37a510549a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41122
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support for the new CONFIG_CBFS_VERIFICATION feature to
cbfstool. When CBFS verification is enabled, cbfstool must automatically
add a hash attribute to every CBFS file it adds (with a handful of
exceptions like bootblock and "header" pseudofiles that are never read
by coreboot code itself). It must also automatically update the metadata
hash that is embedded in the bootblock code. It will automatically find
the metadata hash by scanning the bootblock for its magic number and use
its presence to auto-detect whether CBFS verification is enabled for an
image (and which hash algorithm to use).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I61a84add8654f60c683ef213b844a11b145a5cb7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41121
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `q35-alpine.cfg` adds a lot of PCIe devices to resemble the
topology inside an Intel Alpine Ridge Thunderbolt controller.
By no means could this be detected as such a controller. But
having a real-world example of such a topology can help to
test the allocator and other algorithms on a deeper tree.
It adds two levels of PCIe switches (`alpine-root` and
`alpine-1`), and two endpoints (a `pci-testdev` and an xHCI
controller).
It can be added to the default `q35-base.cfg` config, e.g.
with:
$ make qemu QEMU_EXTRA_CFGS=util/qemu/q35-alpine.cfg
Change-Id: Ieab09c5b67a5aafa986e7d68a6c1a974530408b0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51329
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:49896 added support in `intel_microcode_find()` to cache the found
microcode for faster subsequent accesses. This works okay when the
function succeeds in finding the microcode on BSP. However, if for any
reason, `cpu_microcode_blob.bin` does not contain a valid microcode
for the given processor, then the logic ends up attempting to find
microcode again and again every time it is called (because
`ucode_updates` is set to NULL on failed find, thus retriggering the
whole find sequence every time). This leads to a weird race condition
when multiple APs are running in parallel and executing this
function.
A snippet of the issues observed in the scenario described above:
```
...
microcode: Update skipped, already up-to-date
...
Microcode header corrupted!
...
```
1. AP reports that microcode update is being skipped since the current
version matches the version in CBFS (even though there is no matching
microcode update in CBFS).
2. AP reports microcode header is corrupted because it thinks that the
data size reported in the microcode is larger than the file read from
CBFS.
Above issues occur because each time an AP calls
`intel_microcode_find()`, it might end up seeing some intermittent
state of `ucode_updates` and taking incorrect action.
This change fixes this race condition by separating the logic for
finding microcode into an internal function `find_cbfs_microcode()`
and maintaining the caching logic in `intel_microcode_find()` using a
boolean flag `microcode_checked`.
BUG=b:182232187
TEST=Verified that `intel_microcode_find()` no longer makes repeated
attempts to find microcode from CBFS if it failed the first time.
Change-Id: I8600c830ba029e5cb9c0d7e0f1af18d87c61ad3a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51371
Reviewed-by: Patrick Rudolph
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Follow GT7375P Programming Guide_Rev.0.6 to increase
reset delay to 180ms.
2. Add TOUCH_RPT_EN pin(GPP_A11) control to fix TOUCH_RPT_EN pin
keep high after system suspend.
BUG=b:181711141
TEST=Build and boot boten to OS.
Confirm TOUCH_RPT_EN pin keep low after system suspend.
Change-Id: I98efbe68dab538906802647582eba0e068d9c11f
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51254
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index.
Since all boards do pad setup on their own now, finally drop the pad
configuration from SoC common code.
Change-Id: Id03719eb8bd0414083148471ed05dea62a895126
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I55815a824ea3a77e6e603ba4beb17457f37c48f5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch adds the changes to enable the TCSS.
BUG=b:175808146
TEST= Boot shadowmountain board, Test the functionality of the Type-C
ports on both the mainboard and daughterboard by plugging in the Type-C
devices and verified the devices are detected via EC console and in the
OS.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: Ieaf1170ca718a14d24b773a4a85516e0bbfbb569
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51026
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configuring touch controllers to use edge-triggered interrupts is not
recommended as it is very easy to lose an edge when kernel drivers
disable the interrupt for one reason or another, and recovering from
this condition requires workarounds in the kernel.
Unfortunately the example setting up a touchpad used edge-triggered
interrupts, and this set up has been propagating through the boards.
Let's switch the example to use level interrupts instead.
Change-Id: I4dc8b91ed070ce117553b00a087ad709aeaf16af
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
EFI_PEI_MP_SERVICES_STARTUP_ALL_APS passes in a boolean flag singlethread
which indicates whether the work should be scheduled in a serially on all APs
or in parallel. Current implementation of this function mp_startup_all_aps
always schedules work in parallel on all APs. This implementation ensures
mp_startup_all_aps honors to run serialized request.
BUG=b:169114674
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I4d85dd2ce9115f0186790c62c8dcc75f12412e92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51085
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PSP_SHAREDMEM_BASE made the assumption that _psp_sharedmem_dram would
only match once. With CB:49332 there are now two symbols, and it was
grabbing the wrong one.
This change makes it so we match the exact symbol. It also switches to
using awk to simplify the code.
The bootblock.elf target that is added to the list of prerequisites also
creates the bootblock.map file that gets used to extract the base
address of the _psp_sharedmem_dram symbol.
BUG=b:181354692
TEST=Boot zork past bootblock
Fixes: 82d16b150c ("memlayout: Store region sizes as separate symbols")
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I79675bd73f964282b54bca858830e26de64037c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Some of the previous binaries were incorrect and should not be used
for Majolica because they are templates instead of APCBs specifically
built for the board. This APCB update also places the UMA region under
4G and size 32 MB which is essential for video output.
TEST=Boot with UEFI BIOS and verify we can get to OS. Also verify memory
region size, base and alignment.
Change-Id: Id797e2ad5bd67815c09752aedc19dad7dcf8ad12
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The headers added are generated as per FSP v2081_02.
Previous FSP version was v2037.
Changes Include:
- Adjust UPD Offset in FspmUpd.h and FspsUpd.h
- Add DevIntConfigPtr and NumOfDevIntConfig UPDs in Fsps.h
BUG=b:180758116
BRANCH=None
TEST=Build and boot ADLRVP
Cq-Depend: chrome-internal:3669105
Change-Id: Ib99748a428709ffad27d47f600e00bd91b70d8f3
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51248
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Until now output of all test groups run in single unit test were
saved in the same file which caused Jenkins to fail because
of existence of multiple root XML elements.
Now each test group is saved to its own file containing its name
at the end of the filename.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I21ba512073bc8d8693daad8a9b86d5b076bea03f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
The current driver is using chip registers map to configure the SAR
sensor, which is opaque, especially when the datasheet is not published
widely.
Use more descriptive names, as defined in Linux kernel documentation at
https://www.kernel.org/doc/Documentation/devicetree/bindings/iio/proximity/semtech%2Csx9310.yaml
BUG=b:173341604
BRANCH=volteer
TEST=Dump all tables, check semtech property:
for i in $(find /sys/firmware/acpi/tables/ -type f) ; do
f=$(basename $i); cat $i > /tmp/$f.dat ; iasl -d /tmp/$f.dat
done
In SSDT.dsl, we have:
Package (0x06)
{
Package (0x02)
{
"semtech,cs0-ground",
Zero
},
Package (0x02)
{
"semtech,startup-sensor",
Zero
},
Package (0x02)
{
"semtech,proxraw-strength",
Zero
},
Package (0x02)
{
"semtech,avg-pos-strength",
0x0200
},
Package (0x02)
{
"semtech,combined-sensors",
Package (0x03)
{
Zero,
One,
0x02
}
},
Package (0x02)
{
"semtech,resolution",
"finest"
}
}
Change-Id: I8d1c81b56eaeef1dbb0f73c1d74c3a20e8b2fd7b
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There's no need to finalize the northbridge in SMM. This also makes
unification with Broadwell easier.
Tested on Asrock B85M Pro4, still boots and registers get locked.
Change-Id: I8b2c0d14a79e4fcd2e8985ce58542791cef9b1fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add devicetree configuration parameters for mainboard-specific settings,
and provide reasonable defaults, which should usually be good enough.
This is based on Haswell SA Reference Code version 1.9.0 (Nov 2014).
Tested on Asrock B85M Pro4, registers now have the expected values.
Change-Id: I0dcdd4ca431c2ae1e62f2719c376d8bdef3054bd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47223
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When the SCI_EN bit is set, PM1 and GPE0 events will trigger a SCI
instead of a SMI#. However, SMI_STS bits PM1_STS and GPE0_STS can
still be set. Therefore, when SCI_EN is set, ignore PM1 and GPE0
events in the SMI# handler, as these events have triggered a SCI.
Do not ignore any other SMI# types, since they cannot cause a SCI.
Note that these bits are reserved on APL and GLK. However, SoC-specific
code already accounts for it. Thus, no special handling is needed here.
Change-Id: I5998b6bd61d796101786b57f9094cdaf0c3dfbaa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We saw EXT_PMIC_EN1 and PPVAR_DVDD_PROC_BC power off sequence
failure, and after checking MT6315 MT6315 PMIC protection key
summary.xlsx and MT6315 Top and CLK programming guide.docx,
we found there are something wrong about the sequence of magic
key protection flow and clk setting. Update correct initial
flow.
BUG=b:179000151
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I1b7f970a44904fda09a97f4064eef7c95feefad7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51245
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The initial settings for MT6315 were not applied correctly
because the setup process didn't specify correct slave id
(incorrectly always sending 0), and may cause failure in
power off sequence.
BUG=b:179000151
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: Ifd04da8ac55bcc9f9fdbc088d430522c2725ad47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Intel ADL-P supports an additional memory-mapped 16MiB window into the
platform SPI flash. Support for this window already exists at the SoC
level, so all that is needed is to properly organize the flash map to
take advantage of this. FW_SECTION_A moves down to the bottom of the
available space in the lower 16MiB half, and FW_SECTION_B moves to the
bottom of the top 16MiB half. RW_LEGACY is squashed down to 2M.
BUG=b:182088676
TEST=build and boot to OS from FW_MAIN_A
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I60483b7e638c0a7e41f1f7e2b5503ae02e9906bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Add SOC_INTEL_COMMON_PCH_LOCKDOWN and PMC_GLOBAL_RESET_ENABLE_LOCK
to meet device security requirements.
LOCKDOWN has dependencies on SOC_INTEL_COMMON_PCH_BASE and
several other common block devices. Add COMMON_PCH_BASE and
COMMON_PCH_SERVER to pick up LOCKDOWN and the dependencies.
COMMON_PCH_SERVER adds the following common devices that were not
previously included by XEON_SP:
SOC_INTEL_COMMON_BLOCK_CHIP_CONFIG
SOC_INTEL_COMMON_BLOCK_CSE
SOC_INTEL_COMMON_BLOCK_GPIO_ITSS_POL_CFG
SOC_INTEL_COMMON_BLOCK_ITSS
SOC_INTEL_COMMON_PCH_LOCKDOWN
SOC_INTEL_COMMON_BLOCK_SATA
SOC_INTEL_COMMON_BLOCK_SMBUS
SOC_INTEL_COMMON_BLOCK_XHCI
Change-Id: Iab97123e487f4f13f874f364a9c51723d234d4f0
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Enlarge CONSOLE_CBMEM_BUFFER_SIZE from 128K (default) to 512K, so that
more DRAM calibration logs can be stored in CBMEM console.
BUG=b:181933863
TEST=emerge-asurada coreboot
TEST="cbmem -c" shows the whole full calibration log
BRANCH=none
Change-Id: If82cbee5d2d5e97d98cbdaecda739d91a7cca0f8
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51275
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patchs adds a new CBFS primitive that allows callers to pass in an
allocator function that will be called once the size of the file to load
is known, to decide on its final location. This can be useful for
loading a CBFS file straight into CBMEM, for example. The new primitive
is combined with cbfs_map() and cbfs_load() into a single underlying
function that can handle all operations, to reduce the amount of code
that needs to be duplicated (especially later when file verification is
added). Also add a new variation that allows restraining or querying the
CBFS type of a file as it is being loaded, and reorganize the
documentation/definition of all these accessors and variations in the
header file a little.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I5fe0645387c0e9053ad5c15744437940fc904392
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch pulls control of the memory pool serving allocations from the
CBFS_CACHE memlayout area into cbfs.c and makes it a core part of the
CBFS API. Previously, platforms would independently instantiate this as
part of boot_device_ro() (mostly through cbfs_spi.c). The new cbfs_cache
pool is exported as a global so these platforms can still use it to
directly back rdev_mmap() on their boot device, but the cbfs_cache can
now also use it to directly make allocations itself. This is used to
allow transparent decompression support in cbfs_map().
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0d52b6a8f582a81a19fd0fd663bb89eab55a49d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The new CBFS API contains a couple of trivial wrappers that all just
call the same base functions with slightly different predetermined
arguments, and I'm planning to add several more of them as well. This
patch changes these functions to become static inlines, and reorganizes
the cbfs.h header a bit for better readability while I'm at it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If0170401b2a70c158691b6eb56c7e312553afad1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
If bit 0 of byte 0x47 is set FSP will perform full memory training
even if previously saved data is supplied.
Up to and including FSP 2021 WW01 it was reset internally at the end
of PostMemoryInit. Starting with WW03 this is no longer the case and
Intel advised that this bit should be reset externally if valid MRC
data is present.
Change-Id: I9c4191d2fa2e0203b3464dcf40d845ede5f14c6b
Signed-off-by: Deomid "rojer" Ryabkov <rojer9@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The default value for the LidStatus is "LidClosed" mean 0
Because of this GOP skips graphics initialization assuming
lid is closed even though lid is open. This Patch is to set
LidStatus UPD to 1 whenever RUN_FSP_GOP config is selected.
BUG=b:178461282
BRANCH=None
TEST=Build and boot ADLRVP and verify eDP is coming up in
depthcharge
Change-Id: I1648ae0f06e414b2a686e325acf803deb702b7a5
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Move PRERAM_CBMEM_CONSOLE to SRAM L2C and increase its size from 15K to
400K. With this change, most part of the DRAM full calibration log can
be stored in CBMEM console.
BUG=b:181933863
TEST=emerge-asurada coreboot
TEST=Hayato boots
BRANCH=none
Change-Id: I896884d298e197149f75865e9d00579124a34404
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
To reduce qualification effort, we want to pre-populate DRAM by their
size, package type and geometry so when a new DRAM is introduced we
don't need to spin off a new firmware release.
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I42ee170c159e551e840ab4e748f18f5149506b4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51202
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mediatek has released the reference implementation for DRAM
initialization in vendorcode/mediatek/mt8192/dramc (CB:50294)
so we want to use it to replace the derived calibration code
in soc folder.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I2b2f41d774c6b85f106867144fb0b29a4a1bdfcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This is the DRAM initialization code from the reference
implementation released by Mediatek for MT8192.
The DRAM calibration code can be taken as a standalone
library, used by different boot loaders for initializing
DRAM and following a different coding style (coreboot was
using Linux Kernel coding style), so we have to put it
in vendor code folder.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I3853204578069c6abf52689ea6f5d88841414bd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use the common PCIEXP_HOTPLUG code to generate a dummy device for PCIe
ports supporting hotplug. This allows to have control over how much
resources are allocated to hotplug ports.
Tested on thinkpad X220: now hotplugging a dGPU via the expresscard
slot sometimes works.
Change-Id: I3eec5214c9d200ef97d1ccfdc00e8ea0ee7cfbc6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph
This change moves GPE configuration from brya0/overridetree.cb to
baseboard/devicetree.cb since all variants will end up using the same
configuration.
TEST=Verified using "abuild -p none -t google/brya -b brya0
--timeless" that coreboot.rom generated with and without this change
is the same.
Change-Id: Ie31bf2bf8a91da82fca77c78fb0a735a2645de55
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Implement the mainboard_tcss_get_port_info weak function so that the TCSS
muxes can be properly configured to ensure mapping is correct in mux. This
ensures that any devices that are connected during boot are not improperly
configured by the Kernel.
BUG=b:180426950
BRANCH=firmare-volteer-13672.B
TEST= Verified that the SOC code that initialized TCSS muxes to disconnect
mode is executing properly for all TCSS ports and verified that USB3 devices
are no longer downgrading to USB2 speed if connected during boot.
Change-Id: I59e5c5a7d2ab5ef5293abe6c59c3a585b25f7b75
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
TCSS muxes being left uninitialized during boot is causing some USB3
devices to downgrade to USB2 speed. To properly configure the Type C ports
the muxes should be set to disconnected state during boot so that the port
mapping of USB2/3 devices is properly setup prior to Kernel initializing
devices.
BUG=b:180426950
BRANCH=firmware-volteer-13672.B
TEST= Connected USB3 storage device and rebooted the system multiple
times to verify that devices were no longer downgrading to USB2 speed.
Change-Id: I4352072a4a7d6ccb1364b38377831f3c22ae8fb4
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Continue unifying Lynx Point and Wildcat Point (PCH for Broadwell) code.
Define the WPT-LP SMBus PCI device ID, add it to smbus.c of Lynx Point,
and drop all now-unnecessary SMBus code from Broadwell.
Change-Id: I864d7c2dd47895a3c559e2f1219425cda9fd0c17
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add marshaling and unmarshaling support for cr50 vendor sub-command to
reset EC and a interface function to exchange the same.
BUG=b:181051734
TEST=Build and boot to OS in drawlat. Ensure that when the command is
issued, EC reset is triggered.
Change-Id: I46063678511d27fea5eabbd12fc3af0b1df68143
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The datasheet indicates that this bit is reserved. However, subsequent
patches need to use this macro in common code, or else builds fail. To
iron out this difference, mask out the bit in `soc_get_smi_status`, so
that common code always sees it as zero. Finally, add an entry for the
bit in `smi_sts_bits` for debugging usage, noting that it is reserved.
Change-Id: Ib4408e016ba29cf8f7b125c95bfa668136b9eb93
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
1. No gpio control in bootblock
2. Power on and then deassert reset at the end of ramstage gpio
3. Disable power and assert reset when entering S5
On "reboot", the amount of time the power is disabled for is
equivalent to the amount of time between triggering #3 and wrapping
around to #2.
This change affects the following volteer variants that include an FPMCU:
1. Drobit
2. Eldrid
3. Elemi
4. Halvor
5. Malefor
6. Terrador
7. Trondo
8. Voema
9. Volteer2
10. Voxel
BUG=b:178094376
TEST=none
Change-Id: Ib51815349cea299907c10d6c56c27bd239e499e7
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The original implementation of early tcss resulted in calling to mainboard
then back to soc then back to mainboard to properly configure the muxes.
This patch addresses that issue and instead just gets all the mux
information from mainboard and does all config in the soc code.
BUG=none
BRANCH=firmware-volteer-13672.B
TEST=Verified functionality is not effected and early TCSS still functions
Change-Id: Idd50b0ffe1d56dffc3698e07c6e4bc4540d45e73
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
`pmc_send_ipc_cmd()` expects the caller to pass in a pointer to a valid
request and response buffer. However, early_tcss driver was passing in
a NULL pointer for response buffer which would result in invalid
access by `pmc_send_ipc_cmd()`.
Currently, the response buffer is not used in `update_tcss_mux()`. So,
this change drops the passing of `rbuf` parameter to `send_pmc*`
helpers and instead uses a local `rsp` variable in the respective
functions. All the PMC functions used in early_tcss driver return some
kind of response. These should be checked to return appropriate
response code back to the caller. However, this needs to be done as a
separate change.
Change-Id: I215af85feed60b6beee17f28e3d65daa9ad4ae69
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
In commit 2609eaaa8f (src/drivers/i2c/rx6110sa: Omit _HID temporarily)
the randomly assigned and therefore wrong ACPI ID for RTC RX6110SA was
removed. In the meantime Seiko-Epson did a great job and registered an
official vendor ID in the ACPI database [1]. Further on, Seiko-Epson
has now assigned the unique Product Identifier for the RX6110SA, which
is '6110'. The assignment of the Product Identifier is controlled by
the vendor and there is no official database where this ID is stored
in. It is up to the vendor to make sure that this ID stays unique.
This patch adds this new vendor and product ID to the driver. Together
with a pending Linux patch this RTC is now useable as ACPI device in
Linux.
[1] https://uefi.org/ACPI_ID_List?search=SECC
Change-Id: I45838162f014a760520692c6dcaae329ad98547d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51176
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Johannes Hahn <johannes-hahn@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This lock bit can be set later, and should also be set for LynxPoint-H.
This eases merging with Broadwell, which already sets this lock bit
after `spi_finalize_ops()` in a dedicated finalisation function.
Tested on Asrock B85M Pro4 (LynxPoint-H), the lock bit is now set.
Change-Id: I5c32127f2b4cfdfeb0e30a64e5bdda89958933cb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47036
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ASL+ Optimizing Compiler/Disassembler version 20200925 remarks:
IASL build/dsdt.aml
Intel ACPI Component Architecture
ASL+ Optimizing Compiler/Disassembler version 20200925
Copyright (c) 2000 - 2020 Intel Corporation
dsdt.asl 222: Name(PSa, Package(){
Remark 2182 - ^ At least one lower case letter found in NameSeg, ASL is case insensitive - converting to upper case (PSA_)
dsdt.asl 228: Name(APSa, Package(){
Remark 2182 - ^ At least one lower case letter found in NameSeg, ASL is case insensitive - converting to upper case (APSA)
Execute the command below to fix all occurences:
git grep -l PSa | xargs sed -i 's/PSa/PSA/g'
Change-Id: Ia458c98a4774fb5745825aecf996a476e66eaa3f
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The `FORCE_ENABLE` and `FORCE_DISABLE` names do not match what FSP UPDs
say, and can be confused with the `PchHdaTestPowerClockGating` UPD.
Replace the enum with a bool, and drop the confusing names. Note that
the enum for Ice Lake was incorrect, but no mainboards used the option.
Change-Id: I2c9b4c6a2f210ffca946ca196299fa672a06ccc7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51154
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make the SATA LED blink when coreboot dies. GPIO functions aren't
compiled in for postcar, so add a check to prevent linker failures.
TEST: Try to boot Librem Mini WHL without RAM, observe blinking (and
also blinding LED). Re-install RAM (and re-seat RAM a few times),
boot to OS, and observe SATA LED operating normally, as expected.
Change-Id: I0ffac0ab02e52e9fbba7990f401d87e50a1b5154
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50013
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Backport commit 0cded1f116 (soc/intel/tigerlake: Add SMRR Locking
support) to other client platforms. The SMRR MSRs are core-scoped on
Skylake and Ice Lake, at least. Older platforms do not support SMRR
locking, but now there's seven copies of the same file in the tree. A
follow-up will deduplicate smmrelocate.c files into common CPU code.
I cannot test Jasper Lake nor Elkhart Lake, but they should still work.
As per documentation I do not have access to, Elkhart Lake seems to
support SMRR locking. However, Jasper Lake documentation is unclear.
Tested on Purism Librem Mini v1 (WHL-U i7-8565U), still boots and SMRR
MSRs have the same value on all cores/threads (i7-8565U supports HT).
Change-Id: Icbee0985b04418e83cbf41b81f00934f5a663e30
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Booted fine on the first try. Most things work properly, but I haven't
tested them thoroughly. Native raminit chokes with a DIMM in the second
slot, but the first slot works properly.
Change-Id: I2126c7d31e0d8a8f80df69fdcdcd202b87f219a4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
There is going to be an upcoming board version for Drawlat/man and
Drawcia. Hence apply the override GPIO table without pad termination for
board versions 6 or 8 alone.
BUG=None
BRANCH=dedede
TEST=Build and boot to OS in Drawcia.
Change-Id: I320de9a0c37ac033f3efda74eeb8f36e34667fd4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Looks like I forgot about trogdor-rev1 in CB:51004. Unlike rev0 (other
special case) or rev2 (works like CoachZ/Homestar), rev1 used the same
pin as Lazor and Pompom for EN_PP3300_DX_EDP. Apparently there are still
some people using these, so add in another special case for that.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I7093aa63778d69fde240af3b0c62b97ac99c28dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51196
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The legacy DMA is not used by linux. This change frees up those IO
ports.
When FSP-S runs, it re-enables the legacy DMA IO region, so we need to
disable it again.
BOOTBLOCK: PMx00: 0xe3060bf3
ROMSTAGE - Before FSP: PMx00: 0xe3060bf3
ROMSTAGE - After FSP: PMx00: 0xe3060bf7
BUG=b:180949454
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I7792d1f8ea40eb1c7f6cca67e9907208884ac694
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51076
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Even though `device` entries are children of `chip` entries in the
devicetree source format, the chips in the translated C structures
are only hooked up to device nodes. Hence, to configure a chip in
a device- or overridetree, it always needs a `device` below it.
This should fix docking events for the X200 ThinkPad.
Change-Id: I561e7ae81f2e096a091868ce51daa1c8f66af067
Signed-off-by: Nico Huber <nico.h@gmx.de>
Found-by: Kevin Keijzer <kevin@quietlife.nl>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kevin Keijzer
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This function returns true if any GPIO pad is programmed to route the
given IRQ to the IO-APIC. It does so by keeping track of which pads are
routed to IOxAPIC and looking this up in the new function.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iceda89cb111caa15056c204b143b4a17d59e523e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There are platforms that support error correction types other than
single-bit ECC. Extend meminfo to accomodate additional ECC types.
It is assumed that `struct memory_info` is packed to save space. Thus,
use `uint8_t` instead of an enum type (which are usually 4 bytes wide).
Change-Id: I863f8e34c84841d931dfb8d7067af0f12a437e36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50178
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure I2C high / low time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (400 kHz).
Measured I2C frequency just as below after tuning:
touchpad:372 kHz
audio codec RT5682:386.8 kHz
speaker AMP L:387.5 kHz
speaker AMP R:388.9 kHz
BUG=b:181342340
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I05d78c088190e349281a34b2aeed39ae8d867dc2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51112
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If a previous build failed or the build dir is still around for other
reasons (e.g. buildgcc's `-t`) the symbolic link to our `bin` dir we
create there is also still around and can't be created again without
removing it first. Attempts to use `ln -f` also fail as the existing
destination is treated as directory and a new symbolic link would be
created inside.
Change-Id: I7a2720b0286e33d1ba26ea01f323dbf4f8afaea0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch adds new soundwire device ALC1308
The codec properties are filled out as best as possible
with the datasheet as a reference.
The ACPI address for the codec is calculated with the information in
the codec driver combined with the devicetree.cb hierarchy where the
link and unique IDs are extracted from the device path.
The unique ID is calculated from schematics by referring to ASEL[1:0]
strap settings. Datasheet of ALC1308 provides info about the mapping of
ASEL strap settings to unique ID
For example this device is connected to master link ID 1 and has strap
settings configuring it for unique ID 2.
chip drivers/soundwire/alc1308
register "desc" = ""Left Speaker""
device generic 1.2 on end
end
Bug=None
Test=Build and boot on TGLRVP.Extract SSDT and confirm that the entries for
PCI0.HDAS.SNDW are present for ALC1308
Test speaker out functionality
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: Ibf3f1d5c6881cbd106e96ad1ff17ca216aa272ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51042
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sathyanarayana Nujella
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, this function is only invoked for the SPI device through
common SoC code. Since both Intel Harcuvar and Scaleway Tagada have
enabled the SPI device in the devicetree, there's no need to use the
debug version of `pcidev_path_on_root`.
Change-Id: I4340d5860d23c2fa230105f7a7d345c367b2b2aa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50128
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Suresh Bellampalli <suresh.bellampalli@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 15e379aaf3.
It triggers on directories that only contain artifacts and no
checked in code. As this happens a lot when switching branches,
it makes it impossible to commit new code.
Change-Id: I38a86c8a5d5dc14ca5f6cba789bcb8c0fcaefb0b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Taken from document 322170-028 (5 series specification update).
Tested on out-of-tree HP ProBook 6550b (HM57), fixes several issues.
Without this patch, EHCI controllers had no IRQ assigned and there were
unexpected exceptions about NMIs. With this patch, the issues are gone.
Change-Id: Icd31dd89ba49e38a5e4c108a8361dbf636332ab8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51066
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fetch second source factory cache configuration (SSFC) as an optional
element to the firmware config interface. Introduce a Kconfig so that it
can be enabled and used on required mainboards.
BUG=b:177055126
TEST=Build and Boot to OS in Magolor.
Change-Id: I81137406d21e77b5d58a33f66778e13cf16c85c7
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51094
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To supply memory information for Guybrush, the lpddr4x script for
generating SPDs needs to be updated for Cezanne.
BUG=b:178722935
TEST=Add the part used on Majolica to the global lpddr4x json file
and verify that the output is similar to the actual SPD used for
Majolica.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I1f522cb4a92b4fe4c26cad0689437c33ec44befe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51015
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With this change NMI works in the kernel:
----------------
| NMI testsuite:
--------------------
remote IPI: ok |
local IPI: ok |
--------------------
Good, all 2 testcases passed! |
---------------------------------
See setup_lapic() for where this gets configured.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia391ec5a015d909462ff8aaf3cb047c6fd45fe0a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
This function should be using the RK_CLRSETBITS() macros to access the
special Rockchip write-mask registers, like the rest of our code. Also,
there were already existing bit field definitions for these bits that
should be used (although it makes sense to adjust them a bit to allow
passing in the channel number).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If1f5c06aabb16045d890df3bbd271f08a2cdf390
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51080
Reviewed-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
From JSL FSP v2376 "FirmwareVersionInfo.h" header file is
added and "FirmwareVersionInfoHob.h" is deprecated. This patch
adds support to display firmware version information using
"FirmwareVersionInfo.h" header file.
Changes included in this patch:
- Add Kconfig to select FirmwareVersionInfo.h
- Add code change to display firmware version info using
FirmwareVersionInfo.h header
No change in version info print format.
BUG=b:153038236
BRANCH=None
TEST=Verify JSLRVP build with all the patch in relation chain
and verify the version output prints no junk data observed.
couple of lines from logs are as below.
Display FSP Version Info HOB
Reference Code - CPU = 8.7.16.10
uCode Version = 0.0.0.1
Change-Id: I50f7cae9ed4fac60f91d86bdd3e884956627e4b5
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Add the missing PM initialization for Lynxpoint-H. There are some small
changes to Lynxpoint-LP, since some register writes are common among
both PCH variants. This is based on version 1.9.1 of reference code.
Remove the `pch_fixups()` function. The DMI configuration is specific to
Lynxpoint-H. It is not valid for Lynxpoint-LP, which does not have DMI.
Tested on Asrock B85M Pro4, still boots. Registers have the new values.
Without this patch, nearly all registers don't have the expected values.
Change-Id: Ie3f96f2106f3c23aeb694dd6fb343099fc5784e5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47208
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the blipper variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:179648964
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_BLIPPER
Signed-off-by: chenzanxi <chenzanxi@huaqin.corp-partner.google.com>
Change-Id: I8e67521bd9ab05c257cb3d5d5d4cf506f258bfa7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
CB:50863 refactored the data_training() function to split out read gate
training into a separate function, but in the course of this forgot to
correctly initialize the local obs_err varible in the new function to 0.
This means that it will be used uninitialized, and when it happens to be
non-zero it makes the training process fail. Due to the convoluted
control flow in the function, it seems that GCC's static analyzer
couldn't pick up on this uninitialized use.
The whole variable is unnecessary anyway, all it's used for is to force
the function to return two lines below without doing anything with
side-effects in between. This patch removes the variable and simplifies
the code in all three training functions to avoid this uninitialized use
issue and make everything a bit more readable. (Also restore the
original pre-clang-format continuation line intendations for more
readability.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ia475d64c06f2ec1bf9295742d173ce66717b821c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51079
Reviewed-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This causes the linux kernel to complain:
32/64X address mismatch in FADT/Pm1aEventBlock: 0x00000400/0x00000000FED80800
32/64X address mismatch in FADT/Pm1aControlBlock: 0x00000404/0x00000000FED80804
32/64X address mismatch in FADT/PmTimerBlock: 0x00000408/0x00000000FED80808
32/64X address mismatch in FADT/Gpe0Block: 0x00000420/0x00000000FED80814
The linux kernel also verifies that the PM Timer block only uses IO
ports.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I612b6bfb67d8559127ab2ee8a2fb828493820e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Stamp_boost 1640 parameter is too short to keep APU performance.
Restore parameter to 2500 then APU could have longer boost time (~3xxx sec)
BUG=b:175364713
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Change-Id: Ie08394d0b1a693f71336cb4cb6ce9528dfdce14b
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Because the entries were formatted differently to the baseboard, the
devicetree overrides didn't work as intended, and all 5 entries from
the baseboard were included, and then the overrides were applied, but
the baseboard's entries were kept, so there were duplicate ACPI
entries, which causes errors when parsing the table.
Fixes: 5f30ae3714 ("mb/google/volteer: update thermal table for Eldrid")
BUG=b:181034399
TEST=compile, verify static.c is correct now
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I32fe2eae591ed4d3c08378977c463327f7ee1100
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51044
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The codebase currently has only unix line endings, so add a lint tool
to check for windows line endings.
BUG=None
TEST=Verify that line endings are caught both inside and outside a git
repo.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I6faf99a3184e4843640fb8965f8124de0bc52ce7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This fixes the following 2 complaints:
bucts.c: In function ‘main’:
error: unused parameter ‘envp’
error: ‘bucts_state’ may be used uninitialized in this function.
The bucts_state wasn't real, but the compiler couldn't tell, so use
one variable to check for modifications instead of two.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Iff1aae3441ec366d272e88b6b6634980d61cb8ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Rewrite early QPI initialisation to account for variables in the
register values. Trace replays did not capture these relationships.
Tested on out-of-tree HP 630, still boots.
Change-Id: I5d393e8222be286ab4d4dc074d85f721b07bbca4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49586
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
DPR size is in MiB, but the range boundaries are expressed in KiB. In
addition, DPR and TSEG use the same attributes, so unify both regions.
Also improve a comment about DPR, since `is special` is uninformative.
Change-Id: I4479483e17890b5a4c39165138fa1c5f8215bc84
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46987
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The per-lane registers need to be modified in some cases. Also, MRC
does not have any delay after the loop, so remove it.
Tested on out-of-tree HP 630, still boots.
Change-Id: If02e171d2e999f4a5be5b43ecc5aafe8ca092951
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49585
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Given that the PCI devices/registers being accessed are about QuickPath,
this code must be part of QuickPath init. Move it with the other code.
Tested on out-of-tree HP 630, still boots.
Change-Id: I0854e7f0ce3070eed1adc0603f68a9d1552204d4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49584
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Transform the existing functions so that their functionality does not
overlap. Also, deduplicate printing these values in debug builds.
Tested on out-of-tree HP 630, still boots.
Change-Id: I3f50dcf56284c9648b116bc5aacc0adf2d863b5d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49583
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The platform performs a CPU-only reset after initializing QPI (QuickPath
Interconnect) and before actually performing raminit. The state is saved
in the sticky scratchpad register at MCHBAR + 0x2ca8.
Relocate some QuickPath init to a separate file. All moved functions are
only used within QPI init code, and had to be relocated in one commit.
Tested on out-of-tree HP 630, still boots.
Change-Id: I48e3517285d8fd4b448add131cd8bfb80641e7ef
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49582
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Introduce the `get_bits_420` helper to avoid doing the same thing in
three different ways, and also correct a related register write.
Tested on out-of-tree HP 630, still boots.
Change-Id: Iec87f080714f0f07f5d43200ec01d6d3f31e8120
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49579
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Dummy reads followed by writes are actually read-modify-write operations
in disassembled binaries. Handling of the scratchpad register 0x2ca8 is
still nonsense, but that should be taken care of in a separate commit.
Tested on out-of-tree HP 630, still boots.
Change-Id: Ie33f42ecdb25febf3c82febeca13662232dea9ec
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45606
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We only need to toggle one bit at a time. Introduce `rmw_500` to
simplify the code. The rank population doesn't seem to matter.
Tested on out-of-tree HP 630, still boots.
Change-Id: Ic1a680dae90889c84c9b2c536745e254475ff878
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49577
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since Elkhart Lake and Alder Lake use alphabetical ordering, apply that
to the other platforms. Now there are only two versions of smmrelocate.c
across seven different platforms. They will be unified in follow-ups.
Change-Id: I5425323a6d4eecaa97916b6f2683dff57392157c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50935
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The array was copied from Broadwell, which uses a different bit layout
for SMI_STS. Copy the array from Cannonlake instead, because Skylake
uses the same bit layout. This could be deduplicated in the future.
Change-Id: I1c4df727c549eac6f361754d6011bf302da64c5a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50929
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use different verb tables depending on board revision.
For board revision R03 and older use the existing verb tables.
For revisions newer than R03 use the new verb tables and also
apply the dynamic audio configuration recently added.
Also do the following:
* Use correct NID port mapping
* Fix verb count in ALC888 header
* Fix NID in Intel codec verbs
Change-Id: I24ea9149eb2cddb815ff82744a351c926a94aaef
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
List of changes:
1. Add mainboard Kconfig to Kconfig.name files
2. Handle mainboard names in Kconfig file for adlrvp
3. Created a new devicetree.cb for Adlrvp-m.
3. Add override devicetree for ADL-M RVP.
4. Configure proper PCI and USB ports as per schematics for ADL-M
BUG=None
BRANCH=None
TEST=Able to build ADL-M RVP variants adlrvp_m and adlrvp_m_ext_ec.
Signed-0ff-by: Maulik Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I997b89ba87fb03dfa6a836caec51efd05baa2e8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49871
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Due to some change, the test-toolchain was no longer working, and was
always reporting that the toolchain is out of date.
This fixes the failure, and prints both the expected versions of Clang,
GCC, and IASL on failures.
Additional changes fix some indentation issues and skip trying to update
submodules when the test is run.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ia350f279c3fd3533523996327cc6b2304e0bead4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This adds functionality to mask certain IIO errors on the root complex as recommended by HW vendor.
Tested on DeltaLake mainboard. Boot to OS, verify IIO mask registers are programmed correctly.
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Change-Id: I99f05928930bbf1f617c2d8ce31e8df2a6fd15e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tigerlake TBT only has SW CM support. The polling for "LA == 1" is not
applicable for SW CM platform at the resume sequence. This change
removes the pollng for "LA == 1" to improve resume performance.
BUG=b:177519081
TEST=Boot to kernel and validated s0ix on Voxel board.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I886001f71bf893dc7eda98403fa4e1a3de6b958e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Recommendation from SOC to config IQ=8 for U3 port0,
vboost for all U3 ports for passing ESD pin test.
BUG=b:173476380
BRANCH=zork
TEST=1. emerge-zork coreboot
2. run U3 SI/ESD pin test => pass
Change-Id: I0e6414f686a995536a0fd8aa0f6f70e5a36718a3
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50992
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP expects mp_get_processor_info to give processor specfic apic ID,
core(zero-indexed), package(zero-indexed) and thread(zero-indexed) info.
This function is run from BSP for all logical processor, With current
implementation the location information returned is incorrect per logical
processor. Also the processor id returned does not correspond to the
processor index, rather is returned only for the BSP.
BUG=b:179113790
Change-Id: Ief8677e4830a765af61a0df9621ecaa372730fca
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50880
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If the UPD size in coreboot sizes mismatches the one from the FSP-M
binary, we're running into trouble. If the expected size is smaller than
the UPD size the FSP provides, call die(), since the target buffer isn't
large enough so only the beginning of the UPD defaults from the FSP will
get copied into the buffer. We ran into the issue in soc/amd/cezanne,
where the UPD struct in coreboot was smaller than the one in the FSP, so
the defaults didn't get completely copied.
TEST=Mandolin still boots.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia7e9f6f20d0091bbb4abfd42abb40b485da2079d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Send end of post message to CSME in FSP, by selecting EndOfPost
message in PEI phase. In API mode which coreboot currently uses,
sending EndOfPost message in DXE phase is not applicable.
BUG=b:180755397
TEST=Extract and copy MEInfo tool from CSME Fit Kit to voxel, execute
./MEInfo | grep "BIOS Boot State"
and confirm response shows BIOS Boot State to be "Post Boot".
Change-Id: I1ad0d7cc06e79b2fe1e53d49c8e838f4d91af736
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51012
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
EC does not exist in Bilby platform, so removing EC size from board.fmd
and updating bilby fmap size to 0xfef000.
Removing unused EC FW config options MANDOLIN_HAVE_MCHP_FW and
MANDOLIN_MCHP_FW_FILE.
Change-Id: I9ca4e421b0d80d041ed4046fa20cc16e24a776d0
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Picasso currently declares the BAR region between TOM and IO_APIC_ADDR.
This region includes MMCONF. We don't want to map any PCI BARs in this
region. This also matches what intel does.
See soc/intel/braswell/acpi/southcluster.asl for an example.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9474fd6ac75a7245b3c35151c38186e913219bb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This differs slightly from picasso. The PCI BAR region is between TOM1
and CONFIG_MMCONF_BASE_ADDRESS. This matches what the Intel platforms
are doing. It also matches what linux derives from the e820 tables:
> [mem 0xd0000000-0xf7ffffff] available for PCI devices
Picasso currently declares the region between TOM and IO_APIC_ADDR.
This region includes MMCONF. We don't want to map any PCI BARs in this
region.
TEST=Boot majolica and check logs
pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
pci_bus 0000:00: root bus resource [mem 0xd0000000-0xf7ffffff]
pci_bus 0000:00: root bus resource [bus 00-3f]
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4ff02012795e2166e3a4197071b1136727089318
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50893
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will also be used for cezanne. Stoney also has a similar function,
but it hard codes the scope path. I didn't have a device setup to test
if switching to this function was a no-op. So I left it.
TOM2 isn't used by any ASL, so we could remove it later.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I7c8f476a7735fea61a3244b97988e3ead3b42e79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Move wait for TXT and early ME init out of `collect_system_info`, and
then drop the first call to it. Also drop a useless register read.
Tested on out-of-tree HP 630, still boots.
Change-Id: I9b167f44cbd96864bf1e8b616576af19cbbfd90c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49581
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CrashLog is a diagnostic feature for Intel TGL based platforms.
It is meant to capture the state of the platform before a crash.
The state of relevant registers is preserved across a warm reset.
BUG=None
TEST=CrashLog data generated, extracted, processed, decoded sucessfully on delbin.
Signed-off-by: Francois Toguo <francois.toguo.fotso@intel.com>
Change-Id: Ie3763cebcd1178709cc8597710bf062a30901809
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Added file acpi/sleep.asl is really a copy from persimmon with debug
statement and some comments removed.
Added file acpi/gpe.asl is slightly modified copy from persimmon with
changes that seem valid, considering the other changes present in ASL
for the board.
Rename existing usb.asl to usb_oc.asl for consistency.
Change-Id: I493ad1c110380378bad80e49cd888f47fbe41a92
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Variable OSVR had a static value of 3 and OSFL() did not
actually call _OSI or _OS methods.
The conditional in HDA _INI method of OSVR is dropped and
use of DMA NoSnoop attribute remains disabled to retain
previous behaviour. For soc/amd/picasso a different decision
was made in CB:40782 as HDA _INI method was just dropped and
default configuration enables use of DMA NoSnoop attribute.
Change-Id: I967b7b2afbb43253cccb4b77f6c44db45e2989e4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50592
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:40785 ("soc/amd/hda: Move HDA PCI device from DSDT to SSDT") moved
the HDA device in ACPI from DSDT to SSDT. During this, _INI method
generated in SSDT incorrectly inverted the values for NSEN, NSDO and
NSDI. This change fixes the mistake so that the _INI in SSDT matches
the original _INI in DSDT for HDA device.
Change-Id: I294b561a479b77ab8afb5f3e0de367ad24f3a764
Reported-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
coreboot sets up CLK_PM, ASPM, and L1ss automatically based on related
bits in "Link Capability Register" and "L1 PM Substates Capabilities
Register". coreboot overrides these configs even if the driver sets
them. Therefore, setting up CLK_PM, ASPM, and L1ss in the driver is
redundant and useless.
BUG=b:177955523
BRANCH=zork
TEST="lspci -vvvv" prints are identical with and without this patch;
LV2_LINK_CTRL(0x90) is 0x00110102 with and without this patch.
Signed-off-by: Victor Ding <victording@google.com>
Change-Id: I17c19f4271da426ac2b926b948378dc88131e95a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Now that multiple device trees are supported (chipset, base,
override), base_chip_instance parameter for override device needs to
be set to the base chip instance of the corresponding device in
base/primary tree. This can be achieved by using `get_chip_instance()`
instead of using base_dev->chip_instance in `update_device()`.
TEST=Verified that coreboot.rom generated using timeless shows no
change for all boards.
Change-Id: I42e3f4b83c55f3479b95dbbd7a3721558c32b1c8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
coreboot sets up certain configs (e.g. L1ss) based on the device's
reported capacities; however, this BayHub lv2 driver modifies some
of its capacities after coreboot uses them. Therefore, coreboot may
make incorrect configs based on out-of-date capacities.
This patch moves the driver from ".init" to ".enable" so that the
capacities are set before the rest of coreboot queries them.
BUG=b:177955523
BRANCH=zork
TEST="lspci -vvvv" reported "PCI-PM_L1.2-" and "ASPM_L1.2-" on L1SubCtl1
of both PCI device "00:01.3" and "02.00.0"
Signed-off-by: Victor Ding <victording@google.com>
Change-Id: I857b7c7c6732bbd26de561052affa3a3e7e25737
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This is a µATX mainboard with a LGA1151 socket and two DDR4 DIMM slots.
There are two possible BOM configurations: Sid has no legacy devices,
whereas Manny provides two serial ports, a parallel port, a PCI slot
and PS/2 keyboard/mouse connectors. These boards also have different
Super I/O models: Manny uses an ITE IT8625E, whereas legacy-free Sid
comes with an ITE IT8656E instead.
This coreboot port has been done using a Sid board, thus support for
Manny-specific features is missing. Booting should still be possible,
though: none of these legacy features is essential.
The board has an unpopulated 6-pin header, wired to PCH UART 2. This
can be used to retrieve coreboot logs.
Working:
- Both DIMM slots (Micron CT4G4DFS8213.8FA11, Hynix HMA851U6AFR6N-UH)
- PCH SerialIO UART 2 to get coreboot logs
- Rear USB ports
- Realtek RTL8111 GbE NIC
- Integrated graphics on DVI with libgfxinit
- At least one SATA port
- Flashing internally with flashrom
- S3 suspend/resume
- VBT
- SeaBIOS 1.14 to boot Arch Linux (kernel linux-5.10.15.arch1-1)
Untested:
- Audio
- VGA: DP2VGA chip uses DDI E, and libgfxinit doesn't support DDI E yet
- Front USB headers
- Non-Linux OSes
- PCI slot
- IT8625E peripherals: serial, parallel and PS/2 ports
Change-Id: Iadf11c187307a24b15039a5a716737d9d74944e6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48386
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch changes the memlayout macro infrastructure so that the size
of a region "xxx" (i.e. the distance between the symbols _xxx and _exxx)
is stored in a separate _xxx_size symbol. This has the advantage that
region sizes can be used inside static initializers, and also saves an
extra subtraction at runtime. Since linker symbols can only be treated
as addresses (not as raw integers) by C, retain the REGION_SIZE()
accessor macro to hide the necessary typecast.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ifd89708ca9bd3937d0db7308959231106a6aa373
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This adds initial support for the Pine64 ROCKPro64 board.
The ROCKPro64 (http://pine64.org/rockpro64) is a SBC using the
RK3399 SoC with up to 4GB LPDDR4.
So far only the bootblock part works, the romstage starts to execute,
though.
For ramstage to work we'll need to port some of the changes required
for LPDDR4 vs LPDDR3. This will be addressed in follow up changes.
UART2 on the PI-2 connector can be used as a coreboot console.
GND is pin 6
TXD is pin 8
RXD is pin 10
Flashing:
I used an OpenWRT nightly for the ROCKPro64 and its builtin tool.
$ mtd write coreboot.rom /dev/mtd0
Recovering from a bad flash:
To recover from a bad flash bridging pins 23 and 25 on the PI-2
connector will make the board boot from SD card.
Signed-off-by: Moritz Fischer <moritzf@google.com>
Change-Id: I47d0031fff8ee10b11ad74935eaeb05f1f7eb4b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50625
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Building with LLVM/clang (`COMPILER_LLVM_CLANG=y`), Debian clang version
11.0.1-2 fails due to unknown warning options.
error: unknown warning option '-Wlogical-op'; did you mean '-Wlong-long'? [-Werror,-Wunknown-warning-option]
error: unknown warning option '-Wduplicated-cond' [-Werror,-Wunknown-warning-option]
As these are GCC specific, only add them, when building with GCC (and
not scan-build).
Fixes: 04e0712f46 ("Treewide: Add some gcc's warning options")
Change-Id: I6190c1f3df97fb0be51f8dab7e1f5f2a033f5d86
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The thing that this function initializes is the MPLL (Memory PLL). So,
call it by its name. Also add a missing newline in a printk, and update
a comment on the callsite of this function.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: I86ab643bc87253554346dfed3630eb9ddbd44eb3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This write was copied from Sandy Bridge. Neither Haswell reference code
nor Broadwell perform this write. Therefore, it seems safe to remove it.
Change-Id: I8869ff3e66362d9910235c554c3a07e91f479a82
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46994
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
cbfstool has always had a CBFS_FILENAME_ALIGN that forces the filename
field to be aligned upwards to the next 16-byte boundary. This was
presumably done to align the file contents (which used to come
immediately after the filename field).
However, this hasn't really worked right ever since we introduced CBFS
attributes. Attributes come between the filename and the contents, so
what this code currently does is fill up the filename field with extra
NUL-bytes to the boundary, and then just put the attributes behind it
with whatever size they may be. The file contents don't end up with any
alignment guarantee and the filename field is just wasting space.
This patch removes the old FILENAME_ALIGN, and instead adds a new
alignment of 4 for the attributes. 4 seems like a reasonable alignment
to enforce since all existing attributes (with the exception of weird
edge cases with the padding attribute) already use sizes divisible by 4
anyway, and the common attribute header fields have a natural alignment
of 4. This means file contents will also have a minimum alignment
guarantee of 4 -- files requiring a larger guarantee can still be added
with the --alignment flag as usual.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I43f3906977094df87fdc283221d8971a6df01b53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In a rare placement edge case when adding a file with alignment
requirements, cbfstool may need to generate a CBFS header that's
slightly larger than it needs to be. The way we do this is by just
increasing the data offset field in the CBFS header until the data falls
to the desired value.
This approach works but it may confuse parsing code in the presence of
CBFS attributes. Normally, the whole area between the attribute offset
and the data offset is filled with valid attributes written back to
back, but when this header expansion occurs the attributes are followed
by some garbage data (usually 0xff). Parsers are resilient against this
but may show unexpected error messages.
This patch solves the problem by moving the attribute offset forwards
together with the data offset, so that the total area used for
attributes doesn't change. Instead, the filename field becomes the
expanded area, which is a closer match to how this worked when it was
originally implemented (before attributes existed) and is less confusing
for parsers since filenames are zero-terminated anyway.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I3dd503dd5c9e6c4be437f694a7f8993a57168c2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The *location argument to parse_elf_to_stage() is a relic from code all
the way back to 2009 where this function was still used to parse XIP
stages. Nowadays we have a separate parse_elf_to_xip_stage() for that,
so there is no need to heed XIP concerns here. Having a pointer to
represent the location in flash is absolutely irrelevant to a non-XIP
stage, and it is used incorrectly -- we just get lucky that no code path
in cbfstool can currently lead to that value being anything other than
0, otherwise the adjustment of data_start to be no lower than *location
could easily screw things up. This patch removes it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ia7f850c0edd7536ed3bef643efaae7271599313d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Memlayout is a mechanism to define memory areas outside the normal
program segment constructed by the linker. Therefore, it generally
doesn't make sense to relocate memlayout symbols when the program is
relocated. They tend to refer to things that are always in one specific
spot, independent of where the program is loaded.
This hasn't really hurt us in the past because the use case we have for
rmodules (ramstage on x86) just happens to not really need to refer to
any memlayout-defined areas at the moment. But that use case may come up
in the future so it's still worth fixing.
This patch declares all memlayout-defined symbols as ABSOLUTE() in the
linker, which is then reflected in the symbol table of the generated
ELF. We can then use that distinction to have rmodtool skip them when
generating the relocation table for an rmodule. (Also rearrange rmodtool
a little to make the primary string table more easily accessible to the
rest of the code, so we can refer to symbol names in debug output.)
A similar problem can come up with userspace unit tests, but we cannot
modify the userspace relocation toolchain (and for unfortunate
historical reasons, it tries to relocate even absolute symbols). We'll
just disable PIC and make those binaries fully static to avoid that
issue.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ic51d9add3dc463495282b365c1b6d4a9bf11dbf2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Now that all ACPI names are moved to the corresponding PCI devices, the
functionality in the chip code isn't needed any more.
TEST=No warnings or errors on coreboot console or in the Linux ACPI
parser.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2d39b6d4bd53cd0ca189fb6f55ca26dab68793fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50822
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clang doesn't seem to get along with some of the symbol magic we use for
memlayout and throws -Winline-asm warnings. Since we want to be
compatible with as many host compilers as possible (within reason),
let's disable that warning.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If1d88ed0bb2d10acfadcf8dec74fa3d227e0f790
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Dabros <jsd@semihalf.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Both the IO-APIC and PIC mode PCI IRQ tables are incorrect for ADL; the
2nd field in each package is supposed to be pin, not function number,
and some of the IRQ #s differ from what the FSP programs, therefore
align the ACPI table to match what the FSP is currently programming.
BUG=b:180105941
TEST=boot brya, no more `GSI INT` or `failed to derive IRQ routing`
errors seen in dmesg
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I182be69e8d9ebd854ed74dbb69f4d1f1a539cf2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Bilby is the reference board for AMD Raven, Raven2 and Picasso APUs.
Bilby mainboard code is taken from mandolin variant Cereme.
These new files are a renamed copy and subsequent patches will be
applied to create a working bilby implementation.
Change-Id: I426966d782e259a971ec36bac2498bc62b4ce7e2
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
TEST=Boot majolica to linux and see IO-APIC logs
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
IOAPIC[0]: apic_id 16, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib8094c3edf401659d9d740e2cc6266ddd5f91da9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Enforcing the exact match of FSPS UPD block size between FSP and
coreboot mandates simultaneous updates to coreboot and FSP repos. Allow
coreboot to proceed if its UPD structure is smaller than FSP one. This
usually indicates that FSPS has an updated (larger) UPD structure which
should be soon matched/updated on the coreboot side to keep them in
sync.
While this is an undesirable situation that should be corrected
ASAP, it is safe from coreboot perspective. It is safe (as long as
default values in FSP UPD are sane enough to boot) because FSPS UPD
buffer is allocated on the heap with the size specified in FSPS
(larger) and filled with FSPS default values. This allows FSP UPD
changes to be submitted first followed by changes in coreboot repo.
Note that this only applies to the case when entire FSPS UPD structure
grows which should be rare as FSP should allocate enough reserve space,
anticipating future expansion, to keep the structure from growing when
new members are added.
BUG=b:171234996
BRANCH=Zork
TEST=build Trembyle
Change-Id: I557fd3a1f208b5b444ccf76e1552e74ecf4decad
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Martin Roth <martinroth@google.com>
Without the cast the left shift is done on a 32 bit variable that gets
extended to 64 bits afterwards which results in missing MSBs. To avoid
this, do the cast to 64 bits before the left shift.
Found-by: Coverity CID 1443793, 1443794
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7cfa5b9b6ad71f36445ae2fa35140a8713288267
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The I2C EEPROM on SMBUS needs to be updated with the current board
layout, so that the BMC knows the actual configuration.
Collect all needed information and update the EEPROM if something
changed. Every byte written add a delay of 5 msec.
Change-Id: Ic8485e6c700eede75b1e829238ee70da65118ace
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This only makes sense if relocation via MSR is possible, to relocate
APs in parallel. xeon_sp hardware does not support these MSR.
TESTED: ocp/deltalake boots fine. SMM is relocated on CPU 0 just like
all other cores.
Change-Id: Ic45e6985093b8c9a1cee13c87bc0f09c77aaa0d2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enable Refresh2X to mitigate RAM corruption during long
(> 1hr) periods of S3/suspend, which leads to failure to
successfully resume from S3. Unknown if an issue with all
DRAM types, but tested w/Kingston KVR24S17D8 16GiB DDR4 SODIMMs.
Test: Build/boot Librem Mini v1/v2, put device in suspend,
wait > 1hr, ensure resume from S3 successful 100% of the time.
Change-Id: Ie8e3ebbb1ebdcd98813b5f36f580a235712d2f97
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50756
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To build a CrOS-style zephyr, we need a couple of u-boot tools, so add
them here instead of rebuilding them on every zephyr build (which is
also harder to get right because search paths are no strength of python)
Change-Id: Ib95fcb644ac87c5f35f2228fe081c922452b5213
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
* Check and print errors returned from reading from I2C
* Rework offset calculation by using more macros
* Get rid of stage-specific preprocessor code
* Define the EEPROM layout as struct
* Make use of the defined EEPROM layout to calculate offsets
* Read the UPD to disable VT-d from EEPROM
Change-Id: Iad77811318c7dfd3a3a4f8d523cfa0f457f168b6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48808
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This fixes the following issues:
bincfg.l: In function ‘parsehex’:
error: declaration of ‘val’ shadows a global declaration
bincfg.y: In function ‘generate_binary_with_gbe_checksum’:
error: comparison of integer expressions of different signedness
bincfg.y: In function ‘yyerror’:
bincfg.y:408:28: error: unused parameter ‘fp’
bincfg.y: In function ‘main’:
bincfg.y:452:15: error: unused variable ‘pos’
bincfg.y:451:16: error: unused variable ‘c’
BUG=None
TEST=Build outputs and make sure they're identical.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I60039b741c226a6b6ba53306f6fa293da89e5355
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Gets rid of these 4 warnings:
archive.c: In function ‘set_file_name’:
warning: comparison of integer expressions of different signedness
archive.c: In function ‘add_file’:
warning: comparison of integer expressions of different signedness
archive.c: In function ‘archive_files’:
warning: comparison of integer expressions of different signedness
archive.c: In function ‘convert_endian’:
warning: comparison of integer expressions of different signedness
BUG=None
TEST=Build and run
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I57ee8b31bbc9e97168e3b818c4d053eadf8a4f84
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Fixes these warnings:
warning: alignment 1 of 'struct _psp_directory_table' is less
than 16 [-Wpacked-not-aligned]
warning: alignment 1 of 'struct _psp_combo_directory' is less
than 16 [-Wpacked-not-aligned]
In function 'find_register_fw_filename_bios_dir':
warning: implicit conversion from 'enum _amd_fw_type' to
'amd_bios_type' {aka 'enum _amd_bios_type'} [-Wenum-conversion]
BUG=None
TEST=Build and verify binaries are identical.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I761d9893ac6737b42af96c4b2a57c5a4fc61ab05
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Additionally to the PCI IDs of Cezanne it also handles the Renoir ones.
The main difference between those two is that Renoir has two core
complexes while Cezanne only has one core complex. I haven't seen
incompatible changes between those two though, so for example the fabric
IDs are the same and the one that's only present in Renoir is just not
used in Cezanne. Also adding the ACPI parts for those don't have
anything to do with those differences.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3b2517bc15d872f41183a33857333f1972ff2cb9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Only the call in `spi_flash_cmd_write_page_program` uses non-constant
values for the array length. However, the value for `data_len` has an
upper bound: `flash->page_size` is set to `1U << vi->page_size_shift`
which depends on the flash chip vendor info, and the largest value it
can currently have is 8. Thus, the maximum page size is currently 256.
Define the `MAX_FLASH_CMD_DATA_SIZE` macro to place an upper bound on
the amount of data that can be written in one command. Then, use this
value to allocate a fixed-size buffer in `spi_flash_cmd_write`. Also,
add a check to prevent buffer overflow problems. Finally, ensure that
the `spi_flash_cmd_write_page_program` function always writes no more
than 256 bytes of data when using the `spi_flash_cmd_write` function.
Tested on Asrock B85M Pro4 (Winbond W25Q64FV), MRC cache still works.
Change-Id: Ib630bff1b496bc276616989d4506a3c96f242e26
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Move `CROS_GPIO_DEVICE_NAME` to a new `chromeos.h` header, because
Lynxpoint uses a different value. Also drop unnecessary includes.
Tested with BUILD_TIMELESS=1, Google Tidus remains identical.
Change-Id: I38baed2c114fb93cfb82535a6ec00fb67e596d64
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50080
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use `lp_gpio.h` from Lynxpoint instead. Subsequent commits will update
the mainboards and then drop all GPIO code from Broadwell.
Tested with BUILD_TIMELESS=1, Google Tidus remains identical.
Change-Id: Idef89037c2ca781ac3e921abb4b3dc3f7c4b3b5f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50079
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move prmrr_core_configure before clearing MCEs.
This is required for the following patch in order to update microcode
after PRMRR has been configured, but before MCEs have been cleared.
According to Document 565432 this should be no issue in regards to
SGX activation.
Change-Id: Id2808a3989adff493aaf4175cbeccd080efaaedf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Leverage the existing `acpigen_write_CST_package` function.
Yes, bad devicetree values can trigger undefined behavior. The old code
already had this issue, and will be addressed in subsequent commits.
Change-Id: Icec5431987d91242930efcea0c8ea4e3df3182fd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49093
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I'm not 100% sure yet if this code will be common for all AMD SoCs, so
I'll add a copy for Cezanne for now. This part of the code should
probably be reworked after the initial bringup of Cezanne anyway.
DF MMIO register configuration at the beginning of
data_fabric_set_mmio_np:
=== Data Fabric MMIO configuration registers ===
Addresses are shifted to the right by 16 bits.
idx control base limit
0 a3 fc00 febf
1 a3 1000000 fffcffff
2 a3 d000 f7ff
3 a0 0 0
4 a3 fed0 fed0
5 a0 0 0
6 a0 0 0
7 a0 0 0
DF MMIO register configuration at the end of data_fabric_set_mmio_np:
=== Data Fabric MMIO configuration registers ===
Addresses are shifted to the right by 16 bits.
idx control base limit
0 a3 fc00 febf
1 a3 1000000 fffcffff
2 a3 d000 f7ff
3 10a3 fed0 fedf
4 a0 0 0
5 a0 0 0
6 a0 0 0
7 a0 0 0
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia243a0cad311eb210d14d6242c52f599db22515c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50624
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix regression from commit 0dcc0662f3 util/cbfstool: Introduce
concept of mmap_window.
Use of region_end() wraps around at 4 GiB, if utility is run in
32bit userspace. The build completes with an invalid coreboot.rom,
while one can find error message in stdout or make.log:
E: Host address(ffc002e4) not in any mmap window!
Change-Id: Ib9b6b60c7b5031122901aabad7b3aa8d59f1bc68
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Fix regression with commit aa969e887a ACPI: Move PICM declaration.
While mentioned in the commit message there already, the default
value for AMD boards changed from IOAPIC mode to PIC mode.
ACPI 6.3 spec has this text regarding _PIC method:
If the platform CPU architecture supports PIC mode and the method
is never called, the platform runtime firmware must assume PIC mode.
If MADT has IOAPIC entries, OS will want to change to APIC model. But
the method _PIC was not in the global scope so it could not be called
and therefore _PRT continued to report PIC model interrupt routing.
Already fixed for soc/amd/picasso in commit 839f668.
Change-Id: I7f3bb0d45946cec315694de1d540fea4d828348e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
TEST=Boot majolica and see microcode update
CBFS: Found 'cpu_microcode_blob.bin' @0x6900 size 0x15c0 in mcache @0xcf7fe9d8
microcode: patch id to apply = 0x0a50000b
microcode: being updated to patch id = 0x0a50000b succeeded
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If50b1d8b3ebf4b3e6f8a9dd3ab96073e0cb92424
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Stoneyridge used CONFIG_MAX_CPUS and CONFIG_MAX_CPUS + 1 directly as
IOAPIC IDs and Picasso had Kconfig options to configure that, but still
used the common SMBus controller code that used CONFIG_MAX_CPUS as ID
for the FCH IOAPIC. If a board overrides the PICASSO_FCH_IOAPIC_ID
Kconfig option to a value that isn't CONFIG_MAX_CPUS, we'll get a
mismatch between the ID that gets written into the FCH IOAPIC register
and the ID in the corresponding ACPI table. In order to avoid that add
defines to each SOC's southbridge.c and use them in all soc/amd code.
Change-Id: I94f54d3e6d284391ae6ecad00a76de18dcdd4669
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50575
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This allows dropping some preprocessor usage. The `mkhi_end_of_post`
static functions had to be renamed to avoid a name clash. A follow-up
will tidy up the code in me_smm.c to reduce some duplication.
Change-Id: I6357fed3540be87f42d1fd59534666b9092d0652
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49991
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Evgeny Zinoviev <me@ch1p.io>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This allows us to get rid of the `__unused` attributes. Subsequent
commits will separate ramstage and SMM code into separate files.
Tested with BUILD_TIMELESS=1, Asus P8Z77-V LX2 remains identical.
Change-Id: I1aaef5aa23561bee04f8dd9ddca66738bca91bb4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49990
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Evgeny Zinoviev <me@ch1p.io>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Platforms with bd82x6x do not initialise OSYS, so HPET is
always hidden.
The two boards lenovo/x201 and packardbell/ms2290 using
sb/intel/ibexpeak but still including <bd8x62x/acpi/lpc.asl>
initialised OSYS using _OSI() method and showed HPET selectively.
Change-Id: I02fffd439be2a5a9d22afd67e68abce888361214
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49486
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some Trogdor variants will include a fingerprint sensor, so this patch
adds support for its power sequencing. There is a requirement that the
fingerprint power needs to be *off* for at least 200ms, and when it is
turned back on it needs to stabilize for at least 3.5ms before taking
the FPMCU out of reset. We meet these timing requirements by splitting
the sequence across bootblock, romstage and ramstage. On current Trogdor
boards we measured <end of bootblock> to <end of romstage> at ~430ms and
<end of romstage> to <start of ramstage> at 12ms, so we easily meet the
required numbers this way.
BRANCH=trogdor
BUG=b:170284663
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Iccd77e6e1c378110fca2b2b7ff1f534fce54f8ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
On Picasso we missed setting this bit in coreboot and since the default
after reset is 0, we had to rely on the FSP to set this bit. Stoneyridge
and Cezanne have the HPET decode enable bit in the same position in the
same register. In the ACPI table entry written by
southbridge_write_acpi_tables the HPET entry gets added, so we should
make sure that we enable the decode.
TEST=HPET still works on Mandolin.
Change-Id: Ie98dae1d6036748f700f884d4b9653f2e59c24da
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50512
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These definitions were identical to picasso. The only thing I changed
was that I renamed Misc1 and Misc2 to HPET_L and HPET_H.
This change still doesn't write the PCI_IRQ register for all the PCI
devices. We need to refactor the picasso pci_gpp code first.
TEST=Boot majolica and see FCH IRQs being programmed.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic7e637f234d3af426959a9bbd82a0dcf25bb3c8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50451
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use global variables to provide mainboard USB settings, and have the
northbridge code copy it into the `pei_data` struct. For now.
To minimize diffstat noise, this patch does not reindent the now-global
mainboard USB configuration arrays. This is cleaned up in a follow-up.
Change-Id: I273c7a6cd46734ae25b95fc11b5e188d63cac32e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50538
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a µATX mainboard with a LGA1150 socket and two DDR3 DIMM slots.
Working:
- Both DIMM slots
- Serial port to emit spam
- Some USB ports
- Integrated graphics (libgfxinit)
- DVI
- Realtek GbE
- All PCIe ports
- At least one SATA port
- RAM initialization with MRC binary
- Flashing with flashrom
- S3 suspend/resume
- VBT
- SeaBIOS 1.14 to boot Arch Linux (kernel linux-5.10.15.arch1-1)
Broken:
- Audio. It doesn't work on stock firmware either.
I suspect the codec hardware on my board is dead.
Untested:
- PS/2 mouse
- EHCI debug
- Front USB headers
- Non-Linux OSes
- TPM header
- VGA
Change-Id: I9e47747a99c65e488487fbbcac1de15b9bf5c235
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41260
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CPUID result does not change when HyperThreading is disabled on
HT-enabled CPUs, which breaks `generate_cpu_entries`. Use MSR 0x35
instead, which returns the currently-enabled core and thread count.
Also rename the function to `get_logical_cores_per_package, which is
more accurate. Based on commit 920d2b77f2 (cpu/intel/206ax/acpi.c: Fix
get_cores_per_package). The MSR definition is the same for Sandy Bridge
and Haswell.
Change-Id: I5e1789d3037780b4285c9e367ff0e2b0d4365b39
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49099
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, the address size field of AT24 NVM is incorrect, and
Linux v5.4 kernel logs the message below:
at24 i2c-PRP0001:02: Bad "address-width" property: 13
The valid size of the AT24 NVM is 16 bits so modify the value from
0x0D to 0x10.
BUG=b:177655681
BRANCH=none
TEST=Boot volteer and check the kernel log and see "Bad address-width"
error message is not shown.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Ice6c3eac1e023b981217e1d7dc06587fc46b1a02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Bingbu Cao <bingbu.cao@linux.intel.com>
TEST=Majolica still gets to SeaBIOS. Like before this patch the PSP
still has the recovery flag set in its return value, but we likely still
have some problem in the amdfw part or miss some PSP initialization in
FSP.
Change-Id: I9f343452ef2ea6b01f9b2fd0cf6371218d046046
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50537
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This reverts commit 3ac3c4ebac ("abuild: Allow disabling mainboards").
This mechanism helped getting Chrome OS' coreboot divergence sorted
out in the 2015/2016 timeframe but hasn't been used by anybody since
then. Let's not encourage people to push non-working builds without
good reason and discussion (the result of which could be that we
re-introduce this mechanism).
Change-Id: I8e2f2e1a5d4617baa49cbcb1a640a1ea270007ef
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50518
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Not all TCO status bits have a corresponding enable bit. Masking out the
status register with the enable register causes these events to be lost.
Tested on Asrock B85M Pro4, BIOSWR_STS events are now detected.
Change-Id: I49abb5a4a99e943e57e0aaa6f06ff63bdf957cd3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Datasheet is not publicly available. Derive which registers to dump from
IT8625E, since there are mainboards that can use either chip depending
on BOM configuration. Default values are taken from an HP 280 G2 running
a coreboot build that does not configure the Super I/O.
Change-Id: Icc8c56e9cd19e940e85176ac51b8ef978275eb71
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Sometimes boards enable it by default, making the Kconfig option
impossible to disable without messing with the Kconfig files. This
shouldn't happen, so report on such occurrences early.
TEST=Tried building GOOGLE_KOHAKU through abuild with -x, without
-x and both cases after having added a "select CHROMEOS" for testing
and it failed in the "without -x with select" scenario while properly
configuring and passing all other builds.
Change-Id: Ieb6bcbf3e9ca8cd4ced85c7c9ffaa39505f5a9b7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Was copy-pasted from bd82x6x and no mainboard actually needs it.
The few globals moved outside the GNVS will be removed, relocated or
replaced with acpigen later.
Change-Id: I590a355f1bd1e54365b2e329cfdc62384446a15c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49280
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Variable PICM was not inside GNVS region and can use a static
initialisation value.
For most AMD platforms PICM default changes from 1 to 0.
Fix comments about PICM==0 used to indicate use of i8259 PIC for
interrupt delivery.
Change-Id: I525ef8353514ec32941c4d0c37cab38aa320cb20
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49905
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The value should be set by OSPM using some combination of
_OSI() queris in the \_SB._INI() method.
To maintain previous behaviour with this commit, boards where
GNVS osys initialisation was removed now do the same in ASL.
Change-Id: Id4957b12a72fbf7fa988e7ff039e47abcc072e1c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49353
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change enables vboot support. To use it add CHROMEOS=y to your
config.
TEST=Boot majolica and see verstage run, and then see depthcharge load.
coreboot-4.13-1730-g881092709a5e Fri Feb 5 23:50:28 UTC 2021 verstage starting (log level: 8)...
Phase 1
FMAP: area GBB found @ 805000 (458752 bytes)
VB2:vb2_check_recovery() Recovery reason from previous boot: 0x0 / 0x0
Phase 2
Phase 3
FMAP: area GBB found @ 805000 (458752 bytes)
FMAP: area VBLOCK_A found @ 30000 (8192 bytes)
FMAP: area VBLOCK_A found @ 30000 (8192 bytes)
VB2:vb2_verify_keyblock() Checking keyblock signature...
VB2:vb2_verify_digest() HW RSA forbidden, using SW
VB2:vb2_rsa_verify_digest() HW modexp forbidden, using SW
FMAP: area VBLOCK_A found @ 30000 (8192 bytes)
FMAP: area VBLOCK_A found @ 30000 (8192 bytes)
VB2:vb2_verify_fw_preamble() Verifying preamble.
VB2:vb2_verify_digest() HW RSA forbidden, using SW
VB2:vb2_rsa_verify_digest() HW modexp forbidden, using SW
Phase 4
FMAP: area FW_MAIN_A found @ 32000 (3137280 bytes)
VB2:vb2api_init_hash() HW crypto forbidden by TPM flag, using SW
VB2:vb2_verify_digest() HW RSA forbidden, using SW
VB2:vb2_rsa_verify_digest() HW modexp forbidden, using SW
Saving secdata firmware
Saving secdata kernel
Saving nvdata
Slot A is selected
FMAP: area FW_MAIN_A found @ 32000 (3137280 bytes)
CBFS: mcache @0x02017000 built for 9 files, used 0x1ec of 0x800 bytes
CBFS: Found 'fallback/romstage' @0x0 size 0x753c in mcache @0x02017000
BS: verstage times (exec / console): total (unknown) / 116 ms
coreboot-4.13-1730-g881092709a5e Fri Feb 5 23:50:28 UTC 2021 romstage starting (log level: 8)...
Family_Model: 00a50f00
FMAP: area FW_MAIN_A found @ 32000 (3137280 bytes)
CBFS: Found 'fspm.bin' @0x15440 size 0x2257d in mcache @0x02017138
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I43f0c6e33649332057f41f8813a86571b06032f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This doesn't select HAVE_ACPI_TABLES, so no ACPI tables will be
generated for now. There's also no globalnvs.asl that corresponds to
nvs.h yet. The added nvs.h has some currently unused fields, but still
having them in the struct aligns it with Picasso and also might reduce
the noise in future ACPI patches a bit. When most of the ACPI code for
Cezanne has landed, we need to do a cleanup though.
Change-Id: I3d658d284fa67e4da43a89d74686445fd5e93b1f
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
SerialIO is in ACPI mode for google/auron and intel/wtm2, and is
disabled for google/jecht and purism/librem_bdw. Since Broadwell
SerialIO is never used in PCI mode, _ADR can safely be dropped.
Change-Id: I9a99b8209b5c139146012aa4a92f563692b62c5e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This reverts commit 2151f7561d.
Reason for revert: It depends on the shadowmountain ramstage patch.
Error on the builder:
IASL /cb-build/coreboot.0/default/INTEL_SHADOWMOUNTAIN/dsdt.aml
src/mainboard/intel/shadowmountain/dsdt.asl:4:10: fatal error: baseboard/ec.h: No such file or directory
#include <baseboard/ec.h>
^~~~~~~~~~~~~~~~
compilation terminated.
Change-Id: I9fa5e8cc2ad485bf82bfbda151bc46d26faef7ab
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The common code gets moved to soc/amd/common/block/cpu/smm, since it is
related to the CPU cores and soc/amd/common/block/smi is about the SMI/
SCI functionality in the FCH part. Also relocation_handler gets renamed
to smm_relocation_handler to keep it clear what it does, since it got
moved to another compilation unit.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I45224131dfd52247018c5ca19cb37c44062b03eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50462
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Add comments to mem_parts_used.txt to point out that the order of
the entries matters when assigning IDs, so always add a new part
to the end of the file.
* Update existing mem_parts_used.txt to add the same comment.
* No updates to Zork variants, because they use an optional ID, so
the order actually doesn't matter there.
BUG=b:175898902
TEST=create a new variant of dalboz, trembyle, volteer, waddledee,
or waddledoo, and observe that mem_parts_used.txt has the new
verbiage.
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: Iffbd8e69a89b1b7c810c5d25c7a6148d459d8b02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
PEP table is applicable to Skylake platform as well. It is required to
make the kernel load `intel_pmc_core`. Skylake boards can also use S0ix
hooks.
Tested on an out-of-tree Acer Aspire VN7-572G (Skylake-U),
intel_pmc_core kernel module is loaded and reports statuses predictably
via debugfs.
Change-Id: I08d8c1fde4f447e9292a0508649f802fdc2721e1
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49140
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
EDGE IRQ from TS might be invalid to HOST, configure IRQs
as level triggered to prevent TS lost.
BUG=b:179594439
BRANCH=zork
TEST=1. emerge-zork coreboot chromeos-bootimage
2. power on, suspend DUT to check TS is functional
Change-Id: Ibbbc73b37932ba1359ffe6f572a15564bb341025
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50416
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since Jelboz support number pad,
due to one single coreboot for both Jelboz and Shuboz,
modify "overridetree.cb" setting to number pad support for Jelboz.
BUG=b:174964012
BRANCH=master
TEST=emerge-zork coreboot chromeos-bootimage
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ie0219419834b34b6eac589f28d3604f5f1b65679
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
The lb_gpio coreboot table entries use name fields fixed to 16 bytes.
GCC will not allow creating a static initializer for such a field with a
string of more than 16 characters... but exactly 16 characters is fine,
meaning there's no room for the terminating NUL byte. The payloads (at
least depthcharge) can deal with this as well because they're checking
the size when looking at that table entry, but our printk("%16s") does
not and will happily walk over the end until somewhere else in memory we
finally find the next NUL byte.
We should probably try to avoid strings of exactly 16 characters in this
field anyway, just in case -- but since GCC doesn't warn about them they
can easily slip back in. So solve this bug by also adding a precision
field to the printk, which will make it stop overrunning the string.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ifd7beef00d828f9dc2faa4747eace6ac4ca41899
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change uses the following information to determine the
appropriate S0ix states to enable as per PDG document: 607872
for TGL UP3 UP Rev2p2 (section 10.13):
1. SoC - UP3 v/s UP4
2. H/W design - external phy gating, external clk gating, external bypass
3. Devices enabled at runtime - CNVi, ISH
In some cases, it is recommended to use a shallower state for
S0ix even if the higher state can be achieved (e.g. with external
gating not enabled). This recommendation is because the shallower
state is determined to provide better power savings as per the
above document. Deepest state expected on tigerlake up3 based
platforms is S0i3.2.
BUG=b:177821896
TEST=Build coreboot for volteer. Verify that deepest
S0ix substate that is enabled is S0i3.1
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Change-Id: I5f2ac8b72d0c9b05bc02c092188d0c742cc83af9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49766
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implement `mainboard_azalia_program_runtime_verbs` to configure the
Realtek ALC888 codec according to the settings in the EEPROM. The
encoding of the `internal_audio_connection` field is:
0: Disabled
1: Front HP out
2: Internal speaker
Change-Id: I5e0013217838888977aaa9259e0cfb78c82f719f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
On some mainboards, codec configuration depends on settings that are
only known at runtime, which is impossible to specify using one verb
table. Add an optional `mainboard_azalia_program_runtime_verbs` hook
where mainboards can program runtime-dependent codec verbs.
Change-Id: I7efeba5c26051aeb5061cce191ace08c304a6c70
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
On some boards, Azalia configuration depends on config settings that are
not known at compile-time. Expose a function to program a verb table, to
be used in subsequent commits.
Change-Id: Ie9607f6e733df66f0ca26a4bb70e0864ce1d4512
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Recommendation from SOC to config IQ=8 for U3 port0,
vboost for all U3 ports for passing ESD pin test.
BUG=b:175192931
BRANCH=zork
TEST=1. emerge-zork coreboot
2. run U3 SI/ESD pin test => pass
Change-Id: I42a94e03fb6f8230d4356d16b8e0d2164bc61e3f
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
This is a copy/paste of picasso with a few things removed. With this
change we can jump into depthcharge.
Allocated resources:
PCI: 00:00.0 resource base 0 size a0000 align 0 gran 0 limit 0 flags e0004200 index 0
PCI: 00:00.0 resource base a0000 size 20000 align 0 gran 0 limit 0 flags f0000200 index 1
PCI: 00:00.0 resource base c0000 size 40000 align 0 gran 0 limit 0 flags f0004200 index 2
PCI: 00:00.0 resource base 100000 size 1f00000 align 0 gran 0 limit 0 flags e0004200 index 3
PCI: 00:00.0 resource base 2000000 size 1c0000 align 0 gran 0 limit 0 flags f0004200 index 4
PCI: 00:00.0 resource base 21c0000 size cde40000 align 0 gran 0 limit 0 flags e0004200 index 5
PCI: 00:00.0 resource base f8000000 size 4000000 align 0 gran 0 limit 0 flags f0000200 index c0010058
PCI: 00:00.0 resource base 100000000 size 30e340000 align 0 gran 0 limit 0 flags e0004200 index 6
PCI: 00:00.0 resource base 40e340000 size cc0000 align 0 gran 0 limit 0 flags f0004200 index 7
PCI: 00:00.0 resource base 40f000000 size 1000000 align 0 gran 0 limit 0 flags f0004200 index 8
PCI: 00:00.0 resource base 410000000 size 20000000 align 0 gran 0 limit 0 flags f0004200 index 9
PCI: 00:00.0 resource base cfffe000 size 2000 align 0 gran 0 limit 0 flags f0004200 index a
PCI: 00:00.0 resource base ceffe000 size 1000000 align 0 gran 0 limit 0 flags f0004200 index b
TEST=Boot majolica and see depthcharge finally loading:
Starting depthcharge on MAJOLICA...
new_rt5682_codec: chip = 0x1A
Looking for NVMe Controller 0x3004cac8 @ 00:01:07
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I52682ec2a06c7e219c221648f241e18e26a9358e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50339
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Hide the detail of allocation from cbmem from the FSP.
Loading of a BMP logo file from CBFS is not tied to FSP
version and we do not need two copies of the code, move
it under lib/.
Change-Id: I909f2771af534993cf8ba99ff0acd0bbd2c78f04
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
- Add support for ME Soft Temporary Disable Mode. In this mode, ME
doesn't load its kernel and freezes at Bring UP (BUP) phase. This mode
is saved in ME NVRAM (and thus will remain for next reboots and
poweroffs).
- Add support of new CMOS option for Sandy Bridge and Ivy Bridge
ThinkPads.
HOW TO USE
To disable ME:
1. nvramtool -w me_state=Disabled
2. reboot
To enable it back:
1. nvramtool -w me_state=Normal
2. reboot
To check current status:
intelmetool -m
Tested on ThinkPad X230 and ThinkPad X220.
BACKGROUND
There's no Intel documentation that would explain how this should be
implemented, in public. Working binary sequence for MKHI command to put
ME in Soft Temporary Disable Mode, as well as a way to bring ME out of
it (by writing to H_GS register), was found and published by researchers
from PT Security:
1. To disable ME, BIOS issues the disable command (before End of Post)
and reboots. ME is supposed to be disabled on the next boot after
DID (DRAM Init Done).
My numerous tests show that issuing the command and rebooting is not
enough. If we reboot too early, ME will not be disabled. Apparently,
it is doing something in background after receiving the command. It
works with a delay of 500-1000 ms.
I also tried to dump all known (documented) registers, such as GMES
and HFS, before and during the next 2 seconds after execution of the
disable command to find a possible indication that something's
changed in ME and we're ready to reboot. Found nothing
unfortunately.
2. To enable ME back, host writes value 0x20000000 to H_GS.
PT slides don't contain any more information on it, but my tests
show, that after writing this value, GMES[31:28] is changing from
0x01 (BUP phase) to 0x03 (Policy Module) to 0x06 (Host
Communication). Then, after some more time, fw_init_complete bit of
HFS becomes 1.
This means that ME starts loading its kernel immediately, without
reboot.
On the other hand, Lenovo BIOS clearly perform a reboot after
enabling it (one reboot after saving the settings, then ThinkPad
logo appears, and then one more reboot). I'm assuming we have to
reset too.
Change-Id: Ic01526c9731cbef4e8552bbc352133a2415787c2
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Old archive is not available anymore. The tint sources inside the new
archive are the same (something changed in a debian subdirectory but
we aren't using it), so a libpayload_tint.patch is still valid.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: If556fac7d1d8379a022f59ed6aee1450b7bc5aa7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48616
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using MCHBAR32_AND_OR() in these two cases changes the order of
additions slightly. Originally, the MCHBAR offset and the base
register offset (0x5a4/0x5b4) were added first. Due to the added
parentheses in the register macros, now the complete register
offset is calculated first and then added to MCHBAR. Associativity
tells us that this doesn't change the result.
Changes in the resulting binary were verified manually on the
object file.
Change-Id: Id10882225c8e82b02583aa73e73d661c25abdef9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50355
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clean up cosmetics after refactoring the code. Reflow long lines and
align values in the tables, and also remove a now-unnecessary scope.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: I2712c1ad5404d6968d18d762e6048c5da120ff78
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The first RCOMP group (data) is programmed differently, and has its own
tables. Remove the unused first index from the other tables, and adjust
the loop bound accordingly. Cosmetics are cleaned up in a follow-up.
Tested on Asus P5QL PRO (DDR2), still boots.
Change-Id: I3010acbd00f762c91aebeaf1625ed7543b14bf74
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The RCOMP data group is special and is programmed differently. Prepare
to simplify the code by programming it outside of the loop. Subsequent
commits will simplify the logic even further, then clean up cosmetics.
The special DDR3 case in the loop overwrites the command group strength
multiplier value. It doesn't need to be programmed for each RCOMP group.
Add a comment to justify not programming this register while programming
the settings for the RCOMP data group.
Tested on Asus P5QL PRO (DDR2), still boots.
Change-Id: I5c2484f48e3c07e8e787b1894932e342e8e8a75c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
These settings can be programmed with a single register write. Factor
the writes out into a single function to avoid some redundancy.
Tested on Asus P5QL PRO, still boots.
Change-Id: I3a08c255dd2b0deae650c7fe2ba4e1f4d1cef581
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
MRC uses an incorrect mask when programming this register, but the reset
default value is zero and it is only programmed once. As it makes no
difference, we can safely use the correct mask. Document this difference
in a comment to indicate the deviation from MRC behavior is intentional.
The default value for this register was dumped from Asus P5QL PRO.
Change-Id: I93b0c382f76e141b319414258e40a8bfe6c7848a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Consistently use commas after the last element of arrays, and also align
columns of values and comments. Remove `MHz` units from DDR speed values
to avoid confusion, as the memory's actual clock speed is half of these.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: Id13022483c6221ce87d21dd21a5cfe4317a55ccd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Alderlake includes latest VBT (version 237 onwards),which has size of
8.5 KiB. This change is specific to alderlake so utilizing Kconfig option
to increase VBT size specifically for ADL platforms.
BUG=None
BRANCH=None
TEST=Include new VBT and boot the platform. Able to see firmware screen
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Change-Id: I438f4bce0a2dfa208e1cd59d1cd5dd1c5ad50833
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Since I'm not sure if there are non-upstream boards that change the
default of the Kconfig value and the comment says that it needs to match
the binaryPI build, I'll do that change in a follow-up patch to allow
easy local reverts of that.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic0f08c6cb951994be6db19e10f73f0c621521c70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The sub-process calls break make's dependency tracking, hence we have
to always perform the calls if we want to allow automatic, incremental
builds.
We let each rule depend on a new, phony target `force-payload`. It has
roughly the same effect as tagging all the targets as phony, but doing
so would feel wrong as some of them are actual files.
Change-Id: I1bc2406db371e8dddbfdf71f68a6665a5b558f5e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The new `Makefile.payload` can be included by the Makefiles of pay-
loads for in-tree builds. The basic idea is to use libpayload's
build results without the `make install` step, and to ensure that
incremental builds work. For instance, if libpayload's code changes,
a `make` for the payload would automatically update the libpayload
build and rebuild the payload. But if there are no code changes in
libpayload, only updated files of the payload will be re-built.
The configuration of libpayload is supposed to be automatically
generated from a `defconfig` file. If this `defconfig` changes,
libpayload and the payload will be re-built.
Change-Id: If5319f1bf0bcd09964416237c5cf7f8e59f487a2
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47633
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot's Makefile exports a lot of variables that influence make sub-
processes (e.g. for Kconfig). We don't want these variables leak into
sub-processes for (lib)payload builds, hence unexport them.
Change-Id: I8da2d8db6238d456723b9c22bee80c62e97027b0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48940
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot's Makefile exports a lot of variables that influence make sub-
processes (e.g. for Kconfig). We don't want these variables leak into
sub-processes for (lib)payload builds, hence unexport them.
Change-Id: I7d65c0aa6d4550bd6600c437e838339af69496da
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48939
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mark TSEG as reserved, which is done on other platforms as well.
For some reason CorebootPayloadPkg crashes when using the region where
TSEG typically resides, which is basically RAM.
UefiPayloadPkg doesn't show this issue.
Change-Id: I3ae3659349d2a88bc3575fe9675433c054e28832
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
- Add Kconfig option to hide the Management Engine Interface device so
the OS doesn't try to access it, if the Management Engine is in an
inoperable mode, e.g. if me_cleaner is used.
- Also hide the MEI if the ME is in Soft Temp Disable mode.
Change-Id: Ie4a35bf5fc196e0a02b7591cdb8633d38f0c7f3e
Signed-off-by: James Ye <jye836@gmail.com>
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39074
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id a1afae4:
2019-10-02 11:47:45 +0000 - (juniper: initial setup)
to commit id a2390f3:
2020-12-01 08:35:44 +0000 - (servo_v4/usb_pd_policy: Reject SNK->SRC power swap if CC_ALLOW_SRC not set)
This brings in 4022 new commits.
Change-Id: Ib13921aa78a60f88455223eff602296abc424ca8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48212
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There has been some repeated discussion about how header includes should
be formatted, specifically on the topic of chain-including. The coding
style currently doesn't say anything about the topic but clearly people
have some basic assumptions. This patch tries to codify some common
ground rules that are supposed to reflect the existing practice.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ibbcde306a814f52b3a41b58c7a33bdd99b0187e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add support for MP services2 PPIs, which is slight modification
over MP services 1 PPIs. A new API StartupAllCPUs have been added
to allow running a task on BSP and all APs. Also the EFI_PEI_SERVICES
parameter has been removed from all MP PPI APIs.
This implementation also selects the respective MP services PPI version
supported for SoCs
BUG=b:169196864
Change-Id: Id74baf17fb90147d229c78be90268fdc3ec1badc
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change drops the config FSP_PEIM_TO_PEIM_INTERFACE.
FSP_PEIM_TO_PEIM_INTERFACE is used for:
* Auto-selecting FSP_USES_MP_SERVICES_PPI
* Including src/drivers/intel/fsp2_0/ppi/Kconfig
* Adding ppi to subdirs-y
* Setting USE_INTEL_FSP_TO_CALL_COREBOOT_PUBLISH_MP_PPI to y
and is selected by SoCs that want to enable MP PPI services.
Instead of using the indirect path of selecting MP PPI services, this
change allows SoC to select FSP_USES_MP_SERVICES_PPI directly. The
above uses are handled as follows:
* Auto-selecting FSP_USES_MP_SERVICES_PPI
--> This is handled by SoC selection of FSP_USES_MP_SERVICES_PPI.
* Including src/drivers/intel/fsp2_0/ppi/Kconfig
--> The guard isn't really required. The Kconfig options in this
file don't present user prompts and don't really need to be guarded.
* Adding ppi to subdirs-y
--> Makefile under ppi/ already has conditional inclusion of files
and does not require a top-level conditional.
* Setting USE_INTEL_FSP_TO_CALL_COREBOOT_PUBLISH_MP_PPI to y
--> This is set to y if FSP_USES_MP_SERVICES_PPI is selected by SoC.
TEST=Verified that timeless build for brya, volteer, icelake_rvp,
elkhartlake_crb and waddledee shows no change in generated coreboot.rom
Change-Id: I0664f09d85f5be372d19925d47034c76aeeef2ae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50274
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It was commented that the need for the delay was mainly related
to external displays and only with VBIOS execution. Move the
delay such that it is done only when we actually need to execute
the VBIOS aka option rom.
A delay is currently only defined for librem/purism_bdw in
its Kconfig. As the description of the issue sounds like it
would equally happen on other platforms when VBIOS is involved,
promote the Kconfig visible option to global scope.
Change-Id: I4503158576f35057373f003586bbf76af4d59b3d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
For the moment, these are most not used but become a necessity
for a unified <soc/nvs.h> approach.
They would be required for the implementation of _SWS method
for OSPM to determine the reason for system waking up. The related
hardware registers are present with these platforms.
It's expected that ACPI power-management related GNVS entries are
grouped together to form a single struct in later works.
Change-Id: I6d31d39ac1017cd6fdf0ac66b418d1fbb1edf8e0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50193
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
add UPD for RV2 USB3 phy setting adjust.
Note: it only for RV2 silicon and not available for RV/PCO.
Usb 3.1 PHY Parameters:
1. RX_EQ_DELTA_IQ_OVRD_VAL
-Override value for rx_eq_delta_iq. Range 0-0xF
2. RX_EQ_DELTA_IQ_OVRD_EN
-Enable override value for rx_eq_delta_iq. Range 0-0x1
3. Override value for rx_vref_ctrl. Range 0 - 0x1F
4. Enable override value for rx_vref_ctrl. Range 0 - 0x1
5. Override value for tx_vboost_lvl: 0 - 0x7.
6. Enable override value for tx_vboost_lvl. Range: 0 - 0x1
7. Override value for rx_vref_ctrl. Range 0 - 0x1F
8. Enable override value for rx_vref_ctrl. Range 0 - 0x1
9. Override value for tx_vboost_lvl: 0 - 0x7.
10. Enable override value for tx_vboost_lvl. Range: 0 - 0x1
BUG=b:175192931
TEST=Build/verify the valule will been apply on dirinboz
Change-Id: I1d5f69e840952cc5171af1ce8597628d1bede5cb
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50240
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The offsets of ACPI_CPU_CONTROL and ACPI_GPE0_BLK match the ones from
the reference code, but not the PPR. I've submitted a change request for
the PPR, so this mismatch might go away in the future. The case for
HAVE_SMI_HANDLER will be implemented in a future patch. If that one ends
up being identical to the function in soc/amd/picasso, I'll move it to
the common AMD SoC code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If80b841df12d351d5a0c1e0d2e7bf1e31b03447f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This was the only I/O base address in Kconfig, no board changed it and
if a board changed it, it needs to make sure that it won't overlap with
other I/O resources, so just use the same value as constant in the
define instead of the value from Kconfig. Also remove the PICASSO_
prefix from ACPI_IO_BASE.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7ea62f1101ddefa8785da92de5ba2aaf7945694a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
For MT8192 MCUs, replace LZMA compression with LZ4 to speed up boot
process. The loading (plus decompression) time of mcupm.bin and sspm.bin
is consistently reduced by 8ms, respectively.
BUG=b:177389446
TEST=emerge-asurada coreboot
TEST=Hayato booted up
BRANCH=none
Change-Id: Ida35e7f6e0572ad43082e53bcc69bc708cf7da44
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Revise the following aspects to follow coreboot's coding style:
- Drop braces for single-statement condition and loop bodies.
- Use `__func__` to print the current function's name.
- Reflow pointer dereferences to fit in a single line.
- Adjust the `*` position in pointer variable declarations.
- Drop unnecessary `else` statements.
BUG = N/A
TEST = Build Compulab Intense-PC with secure oprom enabled
Change-Id: I780251d946d5bea97658476d61d25555ec768dfc
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Override SMBIOS type 4 max speed. This field should be maximum speed
supported by the system. 3900MHz is expected for Cooper Lake.
Tested=Execute "dmidecode -t 4" to check max speed is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I67edf657a2fe66b38e08056d558e1b360c4b8adc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Now smbios type 4 max speed field will use the maximum speed of
processor itself if CPUID value can be accessed. However, this field
should be the maximum processor speed supported by the system. Here
we use smbios_cpu_get_max_speed_mhz only to get correct value.
Tested=Execute "dmidecode -t 4" to check max speed is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: Iae8e01a5e455709a57d60a840f279685c8aab80f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48636
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ACPI support for battery, AC and lid.
I don't have MacBook Air 4,2 to test, but:
- I tested it on 5,2;
- I found decompiled DSDT for 4,2 and compared registers and bits,
they are the same as on 5,2.
So it should work.
Change-Id: I592cb4501c878fe46684a524e729d32fb1d7920c
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
- Move ACPI code for Apple MacBooks to a separate directory to avoid
its duplication in mainboards
- Add AC and lid implementations for newer generations
- Rewrite old code using the new ASL syntax
Tested on MBA 5,2, MBP 8,1 and MBP 10,1.
Change-Id: I3d4585aac8e3ebbfed6ce4d4e39fbc33ac983069
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Create `FIXED_RCBA_MMIO_BASE` and use it everywhere, except in cases
where a pointer cast would be necessary. Instances in Sandy Bridge MRC
code were left as-is intentionally, so as not to collide with another
cleanup patch train.
Tested with BUILD_TIMELESS=1, these boards remain identical:
- Asus P8Z77-V LX2
- Packard Bell MS2290
Change-Id: I642958fbd6f02dbf54812d6a75d6bc3087acc77a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50036
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the kracko variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:178092096
BRANCH=dedede
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_KRACKO
Change-Id: I7f8c7a4d4967e99896166ec9dd6b7381b7f6e5ed
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add new Kconfig symbols to mark FSP binary as x86_32.
Fix the FSP headers and replace void pointers by fixed sized integers
depending on the used mode to compile the FSP.
This issue has been reported here:
https://github.com/intel/FSP/issues/59
This is necessary to run on x86_64, as pointers have different size.
Add preprocessor error to warn that x86_64 FSP isn't supported by the
current code.
Tested on Intel Skylake. FSP-M no longer returns the error "Invalid
Parameter".
Change-Id: I6015005c4ee3fc2f361985cf8cff896bcefd04fb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Cache the board settings in memory to avoid having to read them from the
EEPROM multiple times. For now, configure the following settings:
- DeepSx
- USB power in S5
- Power state after G3
Change-Id: Id88529a0b064c54fdf341de3856a8877109d4b14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Hermes has an EEPROM with firmware configuration data. Add definitions
to read and verify the `board settings` from the EEPROM. Subsequent
commits will hook up these EEPROM settings.
Change-Id: Id86632192ae53fd6b0e4df5b26b5a0a81e972818
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
A minimum of 100ms delay is required before sending a configuration
request to the downstream components. Since the kernel already adds
100ms, this change drops the extra 100ms delay in TBT PCIe root ports
_PS0 method in order to improve resume time.
BUG=b:177519081
TEST=Boot to kernel and validated various tests on Voxel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ic392f9af6cd739507a80a4ca3fd126088b513304
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50086
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to Tigerlake TDP specifications (doc #575683, table 4-2),
TGL supports different TDP levels depends on CPU segement/package,
IA Cores and graphics configuration. For example, UP3 4-Core GT2
suppots base TDP=28W, Configurable TDP-Down_1=15W and Configurable
TDP-Down_2=12W. This configurable value can be used to select
suitable TDP level
Change-Id: I4242575807caac172b6cbe667839bf6c9241f3c5
Signed-off-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This fixes the fan always running at full speed on ProBook 6360b,
EliteBook 8470p and ProBook 640 G1 (because the fan control command was
not sent).
On the ProBook 6360b, the EC needs about 30 ms to process the first
command on a cold boot, but other models such as the ProBook 640 G1 need
more time.
Change-Id: I8623af75c062d6aa69d4412e0627d426c69019fb
Signed-off-by: Pablo Stebler <pablo@stebler.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
* Use probe_resource instead of find_resource. This prevents
a call to die and instead returns NULL.
* Handle the case where BAR2 isn't present
* Don't hardcode legacy VGA when BAR2 is present. This fixes
graphic initialisation when the Aspeed isn't the primary GPU
and thus doesn't decode VGA cycles.
This makes the coreboot code more similar to the Linux kernel code.
Change-Id: I2a99712a562a57c65f1cd0df7b1d7606681afe9b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50195
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Iac8a6e386b708ae5c4dbf0677bfe05f1358bf8fd
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49442
Tested-by: siemens-bot
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Baytrail had (only) occurence of DwordMemory vs DWordMemory.
Braswell one had bogus comments about the PCI memory range.
The actual region details are dynamically filled in _CRS.
Change-Id: I8d1bf45c6e5520c0b7643602843c665bfb81f9da
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
From the output of 'objdump -x dram.elf', the DRAM blob needs 222K
memory, but currently only 208K is reserved for it. Since MT8192 has 1MB
SRAM L2C, increase SRAM_L2C_END to 0x00300000, and reorganize regions in
SRAM_L2C to have larger DRAM_INIT_CODE (256K). The size of
OVERLAP_DECOMPRESSOR_VERSTAGE_ROMSTAGE is also increased to 252K.
BUG=b:170687062
TEST=emerge-asurada coreboot
TEST=Asurada booted successfully
BRANCH=none
Cq-Depend: chrome-internal:3568265
Change-Id: I062f00739b72cf6b1bb7ac3318b91721fbe226cc
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This change adds the missing `GBB_FLAG_ENABLE_UDC` as a config in
vboot/Kconfig (just like the other GBB flags) and uses its value to
configure GBB_FLAGS Makefile variable. This is done to allow the
mainboard to configure GBB flags by selecting appropriate configs in
Kconfig.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I6b397713d643cf9461294e6928596dc847ace6bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50110
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UPD PlatformDebugConsent field is not configured.
The config SOC_INTEL_ELKHARTLAKE_DEBUG_CONSENT is available but not
used. Use this config value for PlatformDebugConsent.
BUG= N/A
TEST= Build Intel Elkhart Lake
Change-Id: I697fb611dfb23e107fa8ef1543424b9797a7d027
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50108
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add device ID of Cannon Lake PCH-H Mobile HALO SATA controller
in supported device table.
Bug=N/A
TEST=Build of Intel Coffeelake H SO-DIMM DDR4 RVP11 successfully
completed
Change-Id: Ie1c2aa8273a53c47d7b3571394bcd85b59ab1142
Signed-off-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Add SATA controller ID for Cannon Lake PCH-H Mobile HALO
(see document number: 571182)
Add SPDX license header
Bug=N/A
TEST=Build of Intel Coffeelake H SO-DIMM DDR4 RVP11 successfully
completed
Change-Id: Ic7e6ace2a24b4278b04caa58be907d38f4d117cd
Signed-off-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
It is useful to know if MCU have been applied successfully.
On the start of MP init lines similar to:
"AP: slot 1 apic_id 1, MCU rev: 0x0700001d" will be printed.
The example is taken from the log of an ocp/deltalake.
Change-Id: Ia0a6428b41d07f87943f3aa7736b8cb457fdd15a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49840
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change moves the selection of SOC_INTEL_CSE_LITE_SKU into Kconfig
under BOARD_GOOGLE_BASEBOARD_VOLTEER instead of requiring each
individual board to select it.
TEST=Verified that timeless build does not result in any changes.
Change-Id: I2d94931fdc3077794bed5cc51708b5a5d9e64972
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
A new schematic revision indicates that the old wake pin is not used,
and brya will only use 1 IRQ pin from EC, routed to GPP_F17
BUG=b:178605367
TEST=Build test
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: Ia2bc5b1562ab30b4461fc7e3b1a4bc3e370db588
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
1. These are common OCP/Facebook IPMI OEM commands, move from mainboard
into drivers/ipmi/ocp to avoid code duplication and provide better
reusability.
2. OCP Tioga Pass enables IPMI_OCP driver.
Tested=On OCP Delta Lake and Tioga Pass verify the commands still work
correctly.
Change-Id: Idd116a89239273fd5cc7b06c7768146085a3ed69
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
This cleans up the postcar frame setup, which now gets used instead of
just going with TempRamExit MTRR's.
Note that ramstage CPU init sets up different final MTRRs anyway.
TESTED on ocp/deltalake and ocp/tiogapass.
Change-Id: I756c2d479fef859a460696300422f08013a300f1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Allow platforms to use the coreboot postcar code instead of calling
into FSP-M TempRamExit API.
There are several reasons to do this:
- Tearing down CAR is easy.
- Allows having control over MTRR's and caching in general.
- The MTRR's set up in postcar be it by coreboot or FSP-M are
overwritten later on during CPU init so it does not matter.
- Avoids having to find a CBFS file before cbmem is up (this
causes problems with cbfs_mcache)
Change-Id: I6cf10c7580f3183bfee1cd3c827901cbcf695db7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48466
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Before enabling IO decode ranges, current code checks if the DMI SRLOCK
is set to prevent inconsistencies between LPC PCI cfg registers and LPC
DMI registers, when the latter are locked.
DMI SRLOCK only applies to PCHs with on-package DMI, but not to PCH-H,
PCH-S and others with discrete PCH packages. So this check is at least
incomplete.
Further, the lock gets applied by FSP and gets reset on a warm reset.
Thus, there is no case where the lock would be already set at the
places where the DMI registers get written currently.
Drop the checks for the reasons mentioned above.
Change-Id: I59554ce96bce7f7d1a4ba9b098be9e8466c68eac
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49885
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The function to get the PSP mailbox address is the same on Picasso and
Cezanne, so move it to the common PSP generation 2 code. The function is
only used in the same compilation unit, but it can't be marked as static
due to the function prototype in amdblocks/psp.h that is still needed
for Stoneyridge.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieea91ef76523d303f948d29ef48e3b2e56293f26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Was copied from bd82x6x and none of the PCI IDs matches that of Ibex
Peak (PCI_DID_INTEL_IBEXPEAK_HECI1 = 0x3b64). Remove the code. This
allows dropping the me_8.x.c dependency, which never made sense.
Change-Id: I54df1e080048c0599dbee687ec617fb724cb6634
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Note that bootblock.c originally wrote a reserved bit of the PCIEXBAR
register. The `length` bitfield was set to 0, so assume 256 busses.
Moreover, the ASL reservation for MMCONFIG was only for 64 busses.
Change-Id: I7366a5096aacd92401535be020358447650b4247
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49759
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Bootblock enabling needs some special handling. Also, the definition of
the `get_pcie_bar` function is incorrect for Ironlake, so remove it.
With this patch, using 64 and 128 for MMCONF_BUS_NUMBER should work.
However, it has not been tested. Using 256 busses should still work.
Change-Id: Ic466ddc7b80f60af5cbff53583281440f02974c7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49761
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is necessary because ASL Memory32Fixed values cannot contain
operations, even if they can be evaluated to constants. Add a sanity
check in pci_mmio_cfg.h to ensure consistency with MMCONF_BUS_NUMBER.
Change-Id: I8f0b5edf166580cc12c1363d8d6b6ef0f2854be9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50033
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Because the refcode blobs are not redistributable, refcode.c is not
build-tested. Commit 6271dd8459 (soc/intel/baytrail,broadwell: Use
resume_from_stage_cache()) broke building with refcode blobs. Fix a
variable redeclaration error by swapping the order of the code, and
use consistent names for the variables.
Change-Id: Ic8dda8d35086d977b536686e8c80b7961c37860c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use proper types in readXp functions, define `PCH_THERMAL_DEV`, clean up
comments a bit, and use `RCBA32_AND_OR` instead of read32/write32.
Tested with BUILD_TIMELESS=1, Asus P8Z77-V LX2 remains identical.
Change-Id: I95e054d6e52706e06e313068e61484f6cb9a64e5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50038
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With SOC_INTEL_COMMON_BLOCK_ACPI=y the call was made twice,
possibly in the order:
common/block/acpi.c: acpi_wake_source()
common/acpi_wake_source.c: acpi_wake_source()
In this order later call would reset pm1i and gpei in GNVS.
Remove the implementation in block/acpi.c and rename existing
acpi_wake_source.c to block/acpi_wake_source.c.
Change-Id: I74fdae63111e3ea09000d888a918ebe70d711801
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Move all Q35 register definitions into the q35.h header. Note that real
hardware does not have EXT_TSEG_MBYTES, because it is QEMU-specific.
Change-Id: I4c86ac0bb05563dee111b9b4a4a71c1c31198acd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50024
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We want to add some function declarations as static_testable to this
header but including it in a .c file outside of tests will yield a gcc
warning like:
error: 'function' declared 'static' but never defined
[-Werror=unused-function]
It seems these includes aren't necessary anyways so we just remove
them.
Change-Id: I17147136579140b94728ceb1c369b1348714bc53
Signed-off-by: Daniel Gröber <dxld@darkboxed.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
There are efforts to replace Chrome EC with Zephyr. To ensure
Chromebook specific Zephyr developments (that can eventually be
built as part of a coreboot build just like Chrome EC now, and are
built with coreboot-sdk) don't break with Zephyr's toolchain, add
the toolchain to our builders so we can do some sanity checking.
Change-Id: I645a298bc350ebe7651c08aea630bdc6b93856aa
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The patch removes selection of ME_REGION_ALLOW_CPU_READ_ACCESS config in
the SOC_INTEL_CSE_LITE_SKU Kconfig definition since the
ME_REGION_ALLOW_CPU_READ_ACCESS Kconfig selection is done based on the
SOC_INTEL_CSE_LITE_SKU Kconfig in the
southbridge/intel/common/firmware/Kconfig.
TEST=Verified build for JSL
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I9969cce0d433657dd27bab71c132356fb28a35c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50012
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The patch defines default value for ME_REGION_ALLOW_CPU_READ_ACCESS config.
It sets value 'y' if CSE Lite SKU is integrated, otherwise value 'n'. The
config ME_REGION_ALLOW_CPU_READ_ACCESS ensures host has read access to ME
region when the LOCK_MANAGEMENT_ENGINE is enabled and CSE Lite SKU is
integrated.
TEST=Verified build for JSL
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I680a23e27ae2bf4d85bf919134c47882f308af56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49891
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
lint-001-no-global-config-in-romstage error on
D0F0_PCIEXBAR_LO.
DOF0_PCIEXBAR_LO is defined in bootblock.c and
romstage.c.
Place D0F0_PCIEXBAR_XX in local gm35.h.
BUG = N/A
TEST = Build and boot QEMU x86 q35/ich9
Change-Id: Ia5ac9eb797de996186282193647313b9f7b42624
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
The values can be used during SMBIOS type 16 creation.
Tested=On OCP Delta Lake, dmidecode -t 16 to verify.
Handle 0x000A, DMI type 16, 23 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: Single-bit ECC
Maximum Capacity: 1146 GB
Error Information Handle: Not Provided
Number Of Devices: 6
Change-Id: Id8f92dc96a7a3eb2e6db330adda98a7fe6d516c8
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add wifi sar for galith
Using convertible mode of fw config to decide to load custom wifi sar or not.
BUG=b:176206495
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Cq-Depend: chromium:2649378,chrome-internal:3559387
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I0f9a7ddedef550317da4bf798317619ffd1fa979
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Configuring GPP_G7 as NC causes SD card detection issue on sasuke.
So we'd like to remove the GPP_G7 override and keep the baseboard
configuration as native function (SDIO_WP).
BUG=b:175831709
BRANCH=firmware-dedede-13606.B
TEST=Built and verified SDR104 SD card operation on sasuke
Change-Id: If73337b482f04fd263caaa6fed0e54aa87bd876e
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Added device hid info to the MST RTD2141b device on
trembyle.
BRANCH=zork
BUG=b:147402710
TEST=Build and flash BIOS image, see 10EC2141 appears
under /sys/bus/i2c/devices
Signed-off-by: Shiyu Sun <sshiyu@chromium.org>
Change-Id: I97a67f9dbc31cd788d579252d7d355b24d97ca30
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested with TianoCore payload (UefiPayloadPkg).
Working:
- PS/2 keyboard, touchpad
- Both DIMM slots
- Both NVMe ports
- SATA port
- All USB ports
- Webcam
- Ethernet
- Integrated graphics
- Internal microphone
- S3 suspend/resume
- Flashing with flashrom
- Booting to Ubuntu Linux and Windows
Not working:
- Discrete/Hybrid graphics
- Internal speakers
These two require new drivers to work correctly, which will be added and
enabled later.
Change-Id: Iae6e530dcd52df3642cdfe74b65bfff5aa0dd402
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update Extended Maximum Capacity field in SMBIOS type 16 so that
maximum dimm size can be over 2TB.
Tested=Execute "dmidecode -t 16" to check maximum capacity is over 2TB.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I61901c815f9d0daae102e5077a116c0de87240ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
acpigen_write_name_zero() and acpigen_write_name_one() are not
implemented correctly, and are not used anywhere. Drop them in
favor of the more flexible acpigen_write_name_integer() function.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I116fd41624a8e8b536d18d747f21d3131b734dfc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
For builds with MAINBOARD_HAS_CHROMEOS=y but CHROMEOS=n, there
is reduced dsdt.aml size and reduced GNVS allocation from cbmem.
More importantly, it's less error-prone when the OperationRegion
size is not hard-coded inside the .asl files.
Change-Id: I54b0d63a41561f9a5d9ebde77967e6d21ee014cd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49477
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With top-aligned bootblock this is no longer globally needed.
The default maximum is now a generous 256 KiB with couple
platforms having lower limits of 32 KiB and 64 KiB.
Change-Id: Ib1aee44908c0dcbc17978d3ee53bd05a6200410c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The PCI0 MMIO window was defined between TOM and 4 GiB. This was
overlapping with the FCH MMIO devices. The first MMIO device after TOM
is the FCH IOAPIC.
This wasn't causing a problem for linux other than the fact that
/proc/iomem showed all the MMIO devices under the PCI root bridge.
On Windows this was causing all the MMIO devices to have conflicting
resource errors.
BUG=b:175146875
BRANCH=zork
TEST=Boot linux and verify peripherals all work. Boot windows and
verify the i2c controllers show up. The GPIO controller still has a
problem related to power.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Idc409f1318e6da5a693ccbb3da74aafd13f1e058
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49853
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Zork platform was not booting with MCACHE enabled since psp_verstage
had following issues with MCACHE.
Fix all the issues and re-enable MCACHE for Zork.
* psp_verstage should call vboot_run_logic, not verstage_main.
vboot_run_logic calls after_verstage which handles RW MCACHE build.
* It should avoid low-level apis for cbfs access.
cbfs_map will build RO MCACHE if it's the first stage, while other
low-level apis won't.
* It should call update_boot_region before save_buffers
MCACHE should be transferred to x86 so we should build it before
calling save_buffers
BUG=b:177323348
BRANCH=none
TEST=boot Ezkinil
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I08c5f8474600a06e3a08358733a38f70787e944a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49468
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is not the correct way to specify the FixedDMA devices. I'm
removing for now since it adds confusion.
BUG=none
BRANCH=zork
TEST=Boot zork to linux and make sure UART still works
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I17b9c8dbe4f9c4b64ee1bd69cb9b30998e727632
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
In ./include/device/device.h, the struct device_operations is defined
as below.
------------------------------------
#if CONFIG(HAVE_ACPI_TABLES)
unsigned long (*write_acpi_tables)(const struct device *dev,
unsigned long start, struct acpi_rsdp *rsdp);
void (*acpi_fill_ssdt)(const struct device *dev);
void (*acpi_inject_dsdt)(const struct device *dev);
const char *(*acpi_name)(const struct device *dev);
/* Returns the optional _HID (Hardware ID) */
const char *(*acpi_hid)(const struct device *dev);
#endif
------------------------------------
So we also need to add the same #if in the C source.
Change-Id: I488eceacb260ebe091495cdc3448c931cc4a1ae3
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Systems can boot to the OS without a display. Don't kill the boot
process based on a vBIOS error, instead just display a warning.
If the issue is actually fatal for some reason, it's going to die
at some point anyway.
BUG=b:175843172
TEST=Boot morphius to OS without a display
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I7d261321cdbe423dd754f6a354e5f50b53563fcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Like Haswell, Broadwell has a "FSB" speed of 100 MHz. Add the IDs for
both the traditional and ULT variants of Broadwell, because the CPU
driver for Haswell already contains CPUIDs for both Broadwell types.
Without this patch, Broadwell CPUs would hang when trying to print the
first console log message, but only if flashconsole was not enabled.
This was missed in commit f542b7bcef (cpu/intel/haswell: Add Broadwell
CPUIDs and microcode) and went unnoticed until now because the tests
were done with flashconsole enabled, which somehow boots properly even
though the console time tracking would not work (depends on TSC).
Tested on out-of-tree Acer E5-573, fixes booting without flashconsole.
Change-Id: I78a1696771d4d6d2138ec432dc0d8e030f14293b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49939
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do not pass ACPI S3 state as a parameter, by locally
calling acpi_is_wakeup_s3() compiler has better chance
for optimizing HAVE_ACPI_RESUME=n case.
Test for acpi_s3_allowed() is already included in the
implementation of acpi_is_wakeup_s3() and is removed
as redunandant.
For ramstage, acpi_is_wakeup_s3() evaluates to
romstage_handoff_if_resume().
Change-Id: I6c1e00ec3d5be9a47b9d911c73965bc0c2b17624
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49838
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is the new _HID that was used for Raven. It matches the _HID used
by the picasso UEFI bios.
This does change the fixed clock used by linux from 133 MHz to 150 MHz.
BUG=none
BRANCH=zork
TEST=boot linux and verify touch screen and touchpad still function
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I37fcb4a4f0148f4843d026902d694c03aeed3c3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
For board version 6 afterward, it will have external pull-up for
GPP_C12, and remove internal pull-up.
BUG=b:177618684
TEST=emerge-dedede coreboot, check evtest if SW_PEN_INSERTED event
(value:1/0) when insert/eject pen, and eject pen to wake system from s0ix
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I503873afb48384168dcd8a822c7246655898356e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reference code does not run any DMI recipe for Sandy Bridge. Create a
helper function and exit early for Sandy Bridge. The CPUID value will
be used in a follow-up, since DMI setup has stepping-specific steps.
Change-Id: I5d7afb1ef516f447b4988dd5c2f0295771d5888e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48413
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop the old, redundant code for mirroring LPC registers to DMI and make
use of the new common code.
Select the new Kconfig option for LPC DMI mirroring by the option
SOC_INTEL_COMMON_PCH_BASE, which is selected by platforms starting with
SPT, except APL and Xeon-SP. For Xeon-SP, select DMI and the new Kconfig
directly.
APL, even though it's younger than SPT, does not need mirroring.
Test: Set LGMR address by calling `lpc_open_mmio_window` and check that
both the PCI cfg and DMI LGMR register get written correctly.
Tested successfully on clevo/cml-u.
Change-Id: Ibd834f1474d986646bcebb754a17db97831a651f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49593
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Starting with SPT, LPC registers IOD, IOE, LGIR* and LGMR need to be
mirrored to their corresponding DMI registers. Add the required writes
to DMI registers, where the PCI config registers get written.
This is already done in soc code for IOD, IOE and LGIR* by mirroring
the registers later, during PCH init. Also the code mostly matches
accross the platforms. This common implementation will avoid delayed
mirroring of the registers and also deduplicate the code.
This change also adds a new Kconfig that will be selected by platforms
requiring mirroring of LPC IO/MMIO registers to their corresponding DMI
registers.
For making use of this common code, the redundant soc code needs to be
dropped and the newly introduced Kconfig option has to be selected. This
is done in the follow-up change.
Change-Id: I39f3bf4c486a1bbc112b2b453381de6da4bbac4d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Instead of hardcoding paths to the executables, use the version in the
path. This allows the scripts to work on more systems, and allows the
binary version to be changed more easily if needed.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ifcc56aa21092cd3866eacb6a02d198110ec6051d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
"usb2_ports[7]" for internal bluetooth device was configured as
'USB2_PORT_EMPTY' mistakenly in previous patch, so we need to enable
it again.
BUG=None
BRANCH=firmware-dedede-13606.B
TEST=Built and verified BT device existence with lsusb
Change-Id: Id2900152e23bbc2f454d064dc86a9e45e934ea0f
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch adds explicit initializations for the remaining named display
(power) control GPIOs to the bootblock GPIO init code. These pins are
usually mapped to pins that are already configured to pull-downs on
power-on reset so this wasn't really required, but we have already moved
them around so often that you never know when EEs might one day move
them to a pin with a different power-on reset configuration, so it's
better to be explicit.
In one particular case, GPIO(67) (used by CoachZ rev1+ but not by
anything else for the EN_PP3300_DX_EDP pin) is not actually a pull-down
on boot, even though that is claimed by the datasheet. This is likely
due to the fact that it can serve as the SPI_HOLD pin for the boot flash
QSPI bus, so even though our board's boot flash doesn't really use that
pin, it seems that the boot ROM still configures it as such.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I533baa962d2dfc87cfa510f442ed2e8912e0e5b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: mturney mturney <mturney@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Commit 393992f (cpu/mp_init: Fix microcode lock) fixed the semantics
of parallel loading microcode updates.
So now '*parallel = 1' really means loading MCU in parallel, which
seems to fail inconsistently on around 10% of the APs.
Change-Id: I755dd302abbb58537d840852e8e290bea282a674
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49671
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When MAINBOARD_HAS_SPEAKER is false, the SPKR gets _HID PNP0C02. This
conflicts with the LDRC device. PNP0C02 is also used other places in the
picasso code base, so I chose a random _UID for each device. The _UIDs
are unique in the code base so it's easy to search for duplicates.
BUG=b:175146875
TEST=Boot trembyle to linux
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I01be41515e011293e90a6b42b8e34de8ec3ffc18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
From AMD USB phy specialist recommended that for DB port2 (type-A), port3 (type-C C1)
the most effective corrections for the depressed eye are
tx_rise_tune=0x0
tx_pre_emp_amp_tune=0x3
tx_fsls_tune = 0x3
BUG=b:173476380
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass USB 2.0 SI eye diagram verification
Change-Id: Ib31c5d55e30b958d3e552e8d0b4a160947444636
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
From AMD USB phy specialist recommended that for DB port2 (type-A), port3 (type-C C1)
the most effective corrections for the depressed eye are:
tx_rise_tune=0x0
tx_pre_emp_amp_tune=0x3
tx_fsls_tune = 0x3
BUG=b:165209698
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass USB 2.0 SI eye diagram verification
Change-Id: I80afd6bf1257b9a72d0d7651b48d243ebaf5de2f
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
This change adds support for a common block memory driver that can be
used for performing the required operations to read SPD data for
different memory channel DIMMs. This data can then be used by the SoC
code to populate different memory related UPDs.
Most recent Intel platforms follow a similar pattern for configuring
FSP-M UPDs for initializing memory. These platforms use one of the
following topologies:
1. Memory down
2. DIMM modules
3. Mixed
Thus, SPD data is either obtained from CBFS (for memory down topology)
or from on-module EEPROM (for DIMM modules). This SPD data read from
CBFS or EEPROM is then passed into FSP-M using SPD UPDs for different
channels/DIMMs as per the memory organization.
Similarly, DQ/DQS configuration is accepted from mainboard and passed
into FSP-M using UPDs as per the FSP-M/MRC organization of memory
channels.
Different memory technologies on a platform support physical channels
of different widths. Since the data bus width is fixed for a platform,
the number of physical channels is determined by data bus width /
physical channel width. The number of physical channels are different
depending upon the size of physical channel supported by the memory
technology. FSP-M for a platform uses the same set of UPDs for
different memory technologies and aims at providing maximum
flexibility. Thus, the platform code needs to format mainboard inputs
for DQ, DQS and SPD into the UPDs appropriately as per the memory
technology used by the board.
Example: DDR4 on TGL supports 2 physical channels each 64-bit
wide. However, FSP-M UPDs assume channels 16-bit wide. Thus, FSP-M
provides 16 UPDs for SPDs (considering 2 DIMMs per channel and 8
channels with each channel 16-bit wide). Hence, for DDR4, only the SPD
UPDs for MRC channel 0 and 4 are supposed to be used.
This common driver allows the SoC to define the attributes of the
platform:
1. DIMMS_PER_CHANNEL: Maximum DIMMs that are supported per channel by
any memory technology on the platform
2. DATA_BUS_WIDTH: Width of the data bus.
3. MRC_CHANNEL_WIDTH: Width of the channel as used by the MRC to
define UPDs.
In addition to this, the SoC can define different attributes of each
memory technology supported by the platform using `struct
soc_mem_cfg`:
1. Number of physical channels
2. Physical channel to MRC channel mapping
3. Masks for memory down topologies
Using the above information about different memory technologies
supported by the platform and the mainboard configuration for SPD,
the common block memory driver reads SPD data and provides pointers to
this data for each dimm within each channel back to the SoC code. SoC
code can then use this information to configure FSP-M UPDs
accordingly. In addition to that, the common block driver also returns
information about how the channels are populated so that the SoC code
can use this information to expose DQ/DQS information in FSP-M UPDs.
This driver aims at minimizing the effort required for supporting
different memory technologies on any new Intel SoC by reducing per-SoC
effort to a table of configurations rather than having to implement
similar logic for each SoC.
BUG=b:172978729
Change-Id: I256747f0ffc49fb326cd8bc54a6a7b493af139c0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49040
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
None of the mainboards have the magic SpeedStep device, so the C-state
generation function bails out without doing anything. Moreover, this
code is broken and was copied from Sandy Bridge. Thus, drop it.
Change-Id: I580157ee33c599af5fc48b06eeb39cb32c9831ec
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
When SerialIO devices are disabled, their _STA method evaluates to 0,
which means the device is not present. It is expected that OSPM would
not attempt to change the power state of a device that is not present.
Lynxpoint does not have these checks, thus remove them from Broadwell.
Also remove the now-unused Arg1 parameter to avoid warnings from IASL.
Change-Id: Ic5e999ac1171ce49db66bec45c58d8aa5711ec53
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Unlike Ivy Bridge series, there isn't a method to flash coreboot
internally when running vendor firmware (yet). Until someone finds a way
to bypass flash protections, the first flash has to be done externally.
Change-Id: Idaff264f2b7277516d69d1323f1a0c885b28c3db
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This is a trimmed-down version of the Cezanne FSP integration code, so
for example the UPD definitions are empty, which will be addressed
later. Since coreboot just leaves the UPD values at their default, this
is not a problem during the initial platform bring-up.
Change-Id: Ie0fc30120c2455aa2160708251e9d2f229984305
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49445
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The xeon_sp/cpx has a second 'rc' heap inside FSP-M that is statically
allocated at the start of CAR. This breaks FSP 2.0 specification. This
can be worked around in the linker scripts to make sure coreboot and
FSP-M don't fight over the same memory.
Tested
- on ocp/deltalake: boot and the "Smashed stack detected in
romstage!" message at the end of romstage is gone.
- qemu/i440fx: BUILD_TIMELESS=1 results in the same binary.
Change-Id: I6d02b8a46a2a8ef00f34d8f257595d43f5d3d590
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
All Broadwell boards only use the `mainboard_pre_raminit` function to
call `mainboard_fill_pei_data` and optionally `mainboard_fill_spd_data`.
Move the declaration and weak definition of `mainboard_fill_spd_data` to
platform code, replace the call to `mainboard_pre_raminit` in romstage.c
with calls to `mainboard_fill_pei_data` and `mainboard_fill_spd_data`,
and delete all other instances of `mainboard_pre_raminit` for Broadwell.
Finally, delete now-empty romstage.c and spd.h files from mainboards.
Change-Id: I3334b20bd7138bb753b996a137ff106e87c6e8a5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This allows us to drop many now-redundant Kconfig options.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
The default configuration file also remains identical, as expected.
Change-Id: I20b0200550508679bf2533342ce918b221dcf81e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The Picasso VBIOS is not setting the reserved_mask_size correctly. This
change relaxes the constraint to allow bpp_mask <= bits_per_pixel. This
is how the code previously used to work before CB:39002.
BUG=b:177094598, b:177422379
TEST=boot zork and see depthcharge working
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I2e67532fa949fbd673269d8d7f1c0d8af6124ac9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The dummy AOAC parent device was nice because it grouped all the AOAC
devices. Unfortunately windows doesn't like this dummy device and causes
"Not Found" errors. This change moves the AOAC devices to the actual
devices that use them.
BUG=b:175146875
TEST=Boot linux and make sure power resources are enabled/disabled.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Idd4a94baa4358ee4f15c461a5bb54ca925023a13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ib827e9b2919dbd0e16f30b8dfde46348365d9622
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Drop LPC pad configuration code since all boards now do pad
configuration on their own. The comment about LPC_CLKRUNB when using
eSPI is moved to `Documentation/getting_started/gpio.md`.
Change-Id: I710d6aee8c3b2c8282cd321cd0688b9b26abea07
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49410
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CSE Firmware Sync is being performed in romstage currently. But the CSE
board reset is not included as part of romstage. This causes the CSE
firmware sync to use global reset instead of EC assisted AP reset with
the old Cr50 Firmware version. Include the board specific CSE reset in
romstage.
BUG=b:171731175,b:177795247
BRANCH=dedede,volteer,puff
TEST=Ensured that the Drawlat boots to OS with both old(0.0.22) and
new(0.6.7) Cr50 FW versions.
Change-Id: I5e362271ffb68ffd5884279acd1ab0a462195a8a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49850
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Kernel needs to access EC RFWU entry in order to retrieve from EC about
port and mux info and set EC operations like modes change. This change
provides EC RFWU path and update for Retimer driver usage.
BUG=b:162528867
TEST=Booted to kernel and verified EC RFWU path from ACPI SSDT table.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I3817d93cfdeedf15825dab6c537b151fd063338b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49257
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The RFWU byte is defined as Bits[3:0] for port number and Bits[7:4] for
operations. The supported operations are:
RETIMER_FW_UPDATE_PORT_INFO 0
RETIMER_FW_UPDATE_PD_SUSPEND 1
RETIMER_FW_UPDATE_PD_RESUME 2
RETIMER_FW_UPDATE_GET_MUX 3
RETIMER_FW_UPDATE_SET_USB 4
RETIMER_FW_UPDATE_SET_SAFE 5
RETIMER_FW_UPDATE_SET_TBT 6
RETIMER_FW_UPDATE_DISCONNECT 7
BUG=b:162528867
TEST=Booted to kernel and verified RFWU entry from ACPI DSDT ERAM field.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I1ba04c6357b6fd0cc33ffce33e7e430539bace79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49051
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to update the BB retimers for usb4/tbt they need to be turned
on and into TBT mode. Expand the current DSM to allow for the use of an
EC RAM byte RFWU to get the current state of each port and whether or
not it has a retimer. It also allows Kernel to issue state transitions
for the retimer to be put into TBT mode for firmware update.
BUG=b:162528867
TEST=Along with work in progress kernel and EC patches, the Retimer
firmware update is verified under device attached and no device attached
scenarios.
Change-Id: I768cfb56790049c231173b0ea0f8e08fe6b64b93
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
SMBIOS slot information in overrridetree is not overriden
if device already exist in devicetree.
Add support to handle this information from override.
BUG= N/A
TEST= Verify generated static.c on Intel Coffee Lake CRB
Change-Id: I532436aee1d71b79171463124f7b205c145d5b05
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49738
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PMC doesn't response any more due to invalid CNVi GPIO
configuration. This caused a 30 second boot delay in FSP-S.
Use the same values as FSP-S does. Always disable external I2S BT
audio and use NF3 for pad GPP_D5 and GPP_D6.
Tested on Prodrive hermes:
No boot delay can be observed any more.
Change-Id: I6f4a954786ec21512b0dce908d333952e96de048
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49678
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some efuse settings would not be applied automatically, so we need
set the settings manually. The low power consumption would not be
optimal without correct efuse settings.
BUG=b:172636735
BRANCH=none
TEST=see 'pmic_efuse_setting: Set efuses in 11 msecs'
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: Ideb862c3cb0f1fee183804aed74fcf141bf1f5df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
For pq module size registers such as DISP_AAL_SIZE, the high bits
should be HSIZE, while low bits should be VSIZE. Fix the incorrect
settings for these registers where width and height are reversed.
According to MediaTek, there is no practical impact on mt8183 devices,
but it's still nice to get this fixed to avoid future confusion.
BUG=b:171167210
TEST=none
BRANCH=kukui
Change-Id: I4b6aedf9a3ca133fcbe9cb88b99a13d228233e24
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46626
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TSEG is located below TOLUD. The size is configured in ESMRAMC but can
also be configured with "-global mch.extended-tseg-mbytes=5" command
line argument. Note that the size in ESMRAMC needs to be 'invalid' (3)
for this to take action.
coreboot will leave TSEG at the default 1MiB.
Note that even if TSEG does not end up being used, it is likely a good
idea to not put anything there as if SMM gets locked down by something
else it will suddenly be inaccessible.
Change-Id: I5fd82a42d6602f1369bb3c69556c46f537542705
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Broadwell code unconditionally enables timed MWAIT, but not all Haswell
steppings support it. In preparation for merging Haswell and Broadwell,
also enable timed MWAIT on Haswell code, but only if it is supported.
Change-Id: I1d11d62f1801d65ae4d5623994fd55fd35e8f34a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46916
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The old code was broken and register 0x90 didn't even exist any more in
the config space of the SMBus PCI device, so just always return the MMIO
base address of the SMBus controller. As far as I've seen, no board in
tree uses this functionality at the moment.
Change-Id: Ib80d5c928da6022427afb8ccc969fb2aac953c2d
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
There seems to be a bug[1] in the GNU linker for the RISC-V architecture
triggered by symbols that are more than 2GB offset from the program
counter. My next patch is introducing symbols like that and stuck on
this problem. The code path that runs into the issue is only taken when
passing the --emit-relocs flag, which is really only needed for building
rmodules. Since RISC-V platforms don't use any rmodules at the moment,
let's disable the flag on RISC-V until the issue can be fixed in the
toolchain.
[1]: https://sourceware.org/bugzilla/show_bug.cgi?id=27180
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I784a506034325c0ba937589416acaafbf80080e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49449
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to a bootblock gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Change-Id: Iad40b6315a29e7aea612a3e1a169372d296d1d6c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49443
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I357099f797be178543a9e6637335cd0a68633071
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49441
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I8b30eb5d70c34ae3e2ed24ab52dd1357a54c5ae7
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49439
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I0b956427a9cec56d06b03f7f05138f75137b4ea3
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49437
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ibc727302109456eb1d86652c947ce85b3a64c5b2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49436
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I80369ab70d5510cb4f388f3029119e7148361af4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49435
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to a early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Id6b55d7f3d3fbfc5b55497708f24006614760d03
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49434
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I130fd26944169430a84c3609432b1b5283581c99
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49432
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ie3878b47b8e20c51b928a38df9ccedf2d50d478e
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49431
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ib19a4f64eaf25bf2eb47ee60748a68538fc0729a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49430
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I279956f30cbb6fb031cdfe6aaa09b644b6b7d3e7
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49427
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms by
adding an appropriate early gpio table in the bootblock.
The soc code gets dropped in CB:49410.
Change-Id: Ie1e53e72c65fdcfe4be2e01134873aa7858c28ff
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49416
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms.
This is done by adding one missing pad to the early gpio table and
dropping the call to the soc function.
The soc code gets dropped in CB:49410.
Change-Id: I210633d4520fcfab59f68268bd7991557433ce38
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49415
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms by
adding an appropriate early gpio table in the bootblock.
The soc code gets dropped in CB:49410.
Change-Id: If0693a4419c58dde3c4536698940f03c30304b9d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49414
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms.
This is done by adding missing pads to the bootblock gpio table.
The soc code gets dropped in CB:49410.
Change-Id: I95993b1bd4f1fd8b4ac7b21fb89ec4d196b0240a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49412
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I62ffbe36bd7b7675aa0f41a8c6e9214d04ad4ae5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49428
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I6fedcebea3bb31d992bac1e3b21382fea93a8b82
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49429
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ieeb738afd54e77ee853ee109009f611411aa0d4a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49426
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5482f44b361925b7d2dbcbf1065c1be035c68b0b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49424
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I7dcf88d61c305f0598a0a79f8cfa46ef5009564b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do LPC/eSPI pad configuration at board-level to match other platforms by
adding an appropriate early gpio table in the bootblock.
The soc code gets dropped in CB:49410.
Change-Id: Ie33bae481f430a1c4410a0a4e2b2a34a3e78adaa
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49411
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `mobile` suffix is misleading, since desktop CPUs share the same
CPUIDs. Remove unused stepping IDs and add the full CPUIDs instead.
Finally, add Broadwell CPUIDs in preparation for merging CPU code.
Note that steppings for Haswell in various comments are incorrect.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I19e56b8826b1514550ae95e6363b0df2d08e3cb7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46915
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Backport Broadwell's s0ix support to Haswell in preparation to unify
both platforms' CPU code. Note that only ULT variants support s0ix.
This option is currently unused, but will be put to use in subsequent
commits, when switching Broadwell mainboards to use Haswell's CPU code.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I91c6f937c09c9254a6f698f3a6fb6366364e3b2b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46924
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On FSP1.1 platform cbmem_initiailze() is called in
chipset_teardown_car_main(). This causes double
call op cbmem_initialize().
Add call to cbmem_online() to avoid double CBMEM init.
BUG = N/A
TEST = Build and boot on Facebook FBG1701
Change-Id: I449ddfc94f1099d7c0e9005e6a5cf509e1433bb1
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
prog_locate() will load FSP, before CBMEM is initialized.
The vboot workbuffer is used for loading, but
CBMEM_ID_VBOOT_WORKBUF is not available.
A NULL pointer is returned as workbuffer resulting in error
'Ramstage was not loaded!' at second boot.
Initialize CBMEM before calling prog_locate().
BUG = N/A
TEST = Build and boot on Facebook FBG1701
Change-Id: I2f04a326a95840937b71f6ad65a7c011268ec6d6
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
[ 84s] /usr/lib/gcc/i586-suse-linux/10/../../../../i586-suse-linux/bin/ld: msrutils.o:(.bss+0x0): multiple definition of `PresentTypes'; msrtool.o:(.bss+0x14): first defined here
[ 84s] /usr/lib/gcc/i586-suse-linux/10/../../../../i586-suse-linux/bin/ld: msrutils.o:(.bss+0x4): multiple definition of `MsrTypes'; msrtool.o:(.bss+0x18): first defined here
There should be typedefs, not variable definitions.
Change-Id: I663a011e9f1fc169126570d5eac7abe82d204a90
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Increase DCACHE_RAM_SIZE to 32kB and remove "NO_CBFS_MCACHE".
It’s quite safe to increase DCACHE_RAM_SIZE. All LGA775 targets
should have at least 256K L2 cache. That is plenty for XIP RO cache of
bootblock + romstage and a 32K CAR.
Change-Id: I393b2727bd90a990c3108a4dbead62b17d7fc531
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Correct GPIO settings as below reason:
1. GPP_D19/GPP_D20/GPP_D21 not being used but set to NF.
2. GPP_B7 should configure as WWAN SAR detect ODL, but set to NC
BUG=b:175932166
BRANCH=dedede
TEST=emerge-dedede coreboot chromeos-bootimage and boot into emmc
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Id7780d5332551ed3fd20ef14f8b5d31164f16385
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This SOC_INTEL_DISABLE_IGD Kconfig will allow to skip IGD
initialization using FSP GOP and eventually disable the IGD.
TEST=Able to get depthcharge pre-OS splash screen when mainboard
user selects SOC_INTEL_DISABLE_IGD with below HW/FW/SW
configuration:
HW: ADLRVP + AMD Radeon RX 5700 PCI-E DGPU
FW: coreboot with depthcharge as payload for ADLRVP and OpRom for
AMD PCI-E DGPU
SW: Chrome OS RC10 release
Change-Id: I465541cb45c9022d53a5beb3fff1f80660c357c9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Change-Id: I5b99a66fb64683f3647ebff3ab01ceb52058f79c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The code for setting the LPC generic memory range uses an array of fixed
address ranges not needing explicit decoding, to decide if the address
needs to be written to the LGMR register. Most platforms only mistakenly
add the PCH reserved mmio range, that is not decoded generally,
effectively breaking the mechanism. Only APL uses the array correctly.
That code, in it's current state, does not work (except for APL) and
currently, there is not a single user. Thus, drop it before people start
using it.
Change-Id: I723415fedd1b1d95c502badf7b0510a1338b11ac
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I795b8da3c5e1efb51c8fe4673f025839a1c630bc
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I2f484d232a46214ff98168f41f96d56b047892e2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I67bdd9a96928b77a9a178afea7dab03dc370312c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I342b9217af0288a3b525e629aac791eb0f880442
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
We need to write some special values to key protection registers before
applying init_setting table and lp_setting table to PMIC. Otherwise,
those settings won't take effect.
After applying init_setting table and lp_setting table, we lock the
settings by writing zero to key protection registers.
Reference datasheet: MT6359_PMIC_Data_Sheet_V1.5.docx, RH-D-2018-0205.
BUG=b:172636735
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I593d4e02bf0b62ac297957caf4ae1c1837f1f38d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Until now some FSP-S parameters were configured for Siemens APL
mainboards via the Binary Configuration Tool (BCT). For simplification,
the original APL FSP binary should now be used. For this purpose, the
corresponding FSP-S parameters are set via devicetree, respectively via
mainboard_silicon_init_params accordingly.
The following parameters are affected:
- Disable CPU power states (C-states)
- Set lowest Max Pkg Cstate - PkgC0C1
- Disable PCIe Hot Plug for all enabled RPs
- Disable PCIe Transmitter Half Swing for all RPs
- Disable PCIe Active State Power Management (ASPM) for all RPs
- Disable PCIe L1 Substates for all RPs
TEST:
- Compare old with new coreboot log on mc_apl5, found no differences
- Boot Linux v4.4 and check output of 'lspci'
Change-Id: I5af627defd6426140cc9a74bb18db400a8971d72
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
APIC was not referenced anywhere in ASL.
MPEN has references under boards:
getac/p470, roda/rk9, roda/rk886ex.
MPEN has reference also in Intel SpeedStep ASL.
Replace static MPEN with detection of multiple CPUs
installed.
Change-Id: Ib5f06416b23196b7227ccd5814162925c31c084b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The BACKLIGHT_ENABLE pin on this board unfortunately defaults to a
pull-up on power on, meaning the backlight is immediately enabled. Best
we can do about that is to turn it off again early and wait until it is
actually correct in the panel power sequence to turn it back on.
Some panels want an explicit 80ms delay after training the eDP
connection before the backlight is turned on (this is probably just to
avoid temporary display artifacts, but whatever). We don't want to
busy-wait that extra time, so instead just delegate turning on that GPIO
to the payload (which is also in charge of the backlight PWM already).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id8dafbdcb40175fbc9205276eee698583b971873
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
This pulls in the following changes:
* Drop geode_lx
* cpu/amd/model_fxx: Drop unused microcode
* cpu/amd/model_10xx: Drop unused microcode
* soc/mediatek/mt8192: Add dram.elf for DRAM full calibration
* soc/mediatek/mt8192: Add dpm binary
* soc/mediatek/mt8192: Add 4266Mbps flag for dpm & dram blob
* soc/mediatek/mt8192: add SPM firmware
* soc/mediatek/mt8192: Support 26M clock off in SPM
* soc/mediatek/mt8192: Add SSPM firmware
* soc/mediatek/mt8192: Add MCUPM firmware
* soc/mediatek/mt8192: Update MCUPM firmware
* soc/mediatek/mt8192: Support discrete DRAM modules
* mb/amd/majolica: Add APCB configuration files
Change-Id: I5c18349307421707fac71f392b785f3e2bef3acb
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
In order to use the function smbios_mainboard_version()
to query the board revision from the EC.
we need to select GOOGLE_SMBIOS_MAINBOARD_VERSION.
BUG=b:177818769
TEST=1. emerge-volteer coreboot chromeos-bootimage
2. flash the image to the device and check board rev
by using command `dmidecode -t 1 | grep Version`
Change-Id: I2474ee03845356d0775f6da25274f696ad33f935
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Create the sasukette variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:175848514
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_SASUKETTE
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I0a554efe0919dc2f5880f0f7817a37bd4be88ed9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change enables LTE modem for sasuke.
- Add LTE modem device into devicetree
- Add GPIO control for LTE modem power on and off
BUG=177177967
TEST=Built and verified modem device existence with lsusb
Change-Id: I34ba8ab00b73f24d1786ab014e9981b172a63a27
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49163
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Writing 0 to MSR IA32_BIOS_SIGN_ID before fetching this MSRs content
is required. This is how things are done in
cpu/intel/microcode/microcode.c.
The "Intel® 64 and IA-32 Architectures Software Developer’s Manual"
also recommends this: "It is recommended that this field be preloaded
with 0 prior to executing CPUID" (this field being %edx).
Change-Id: I24a87aff9a699ed8ab2598007c8b8562d0555ac5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
- Return the busno based on the stack number.
- Replace pci_mmio_read_config32 with pci_io_read_config32 to get the
register value before mapping the MMIOCFG space.
- Remove the plural `s` as the function now provides one bus number.
Change-Id: I6e78e31b8ab89b1bdcfdeffae2e193e698385186
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Dalboz variants do not use an MST hub; remove the i2c tunnel for it.
That bus is actually connected to the battery on these devices, which
should not be exposed to the AP.
BUG=b:175658311
TEST=builds
BRANCH=zork
Change-Id: If1714a5c441bf185efd2517c7c94e57b5f351f5a
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49628
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We found that the switch frequency of vgpu is at 4~5Mhz with high
current case (> 3.5A) and is at 2.5Mhz with low current case(< 2.8A).
The switch frequency of vgpu should be kept at 2.5Mhz.
The root cause is that phase config of vcore is not disabled, it will
affect the switch frequency of vgpu. Corret the phase setting at
initialization.
BUG=b:172636735
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I48d3729302de9e3343dce79fe6f5ed045d0296a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49005
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It looks like we didn't care to reserve the VGA MMIO (a & b segments)
and the c..f segments, initially. It was probably never needed until
the new resource allocator that will make use of any unclaimed space.
Change-Id: Iebdae64914d9f8301cafc67a5aba933c11294707
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The layout of GNVS has expectation for a fixed size
array for chromeos_acpi_t. This allows us to reduce
the exposure of <chromeos/gnvs.h>.
If chromeos_acpi_t was the last entry in struct global_nvs
padding at the end is also removed.
If device_nvs_t exists, place a properly sized reserve for
chromeos_acpi_t in the middle.
Allocation from cbmem is adjusted such that it matches exactly
the OperationRegion size defined inside the ASL.
Change-Id: If234075e11335ce958ce136dd3fe162f7e5afdf7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Disable all NIDs other than those for the front combo jack.
Adjust attributes to match jack physical location, appearance, etc.
Correct group number for verbs for HDMI output.
Test: run hdajackretask, verify NID characteristics correct for each
verb. Verify headphone detection and output functional.
Change-Id: If9fca5d9795d56bd38c8ea47f8de985c14ac8fab
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49464
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In case of CPU PCIe RPs, the RP numbers might not be contiguous for
all the functions in a slot.
Example: In ADL, RP1 is 00:06.0, RP2 is 00:01.0 and RP3 is 00:06.2 as
per the FSP expectations.
Hence, this change updates the defintion of `struct pcie_rp_group` to
include a `start` member which indicates the starting PCI function
number within the group. All common functions for PCIe RP are
accordingly updated to take the `start` member into account.
Thus, in the above example, ADL can provide a cpu_rp_table as follows:
{
{ .slot = PCIE_SLOT_6, .start = 0, .count = 1 },
{ .slot = PCIE_SLOT_1, .start = 0, .count = 1 },
{ .slot = PCIE_SLOT_6, .start = 2, .count = 1 },
}
Since start defaults to 0 when uninitialized, current PCH RP group
tables don't need to be updated.
Change-Id: Idf80a0f29e7c315105f76a7460c8e1e8f9a10d25
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49370
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Having some symmetry with <soc/nvs.h> now allows to reduce
the amount of gluelogic to determine the size and cbmc field
of struct global_nvs.
Since GNVS creation is now controlled by ACPI_SOC_NVS,
drivers/amd/agesa/nvs.c becomes obsolete and soc/amd/cezanne
cannot have this selected until <soc/nvs.h> exists.
Change-Id: Ia9ec853ff7f5e7908f7e8fc179ac27d0da08e19d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
It would seem that `pres` is an abbreviation for `presence`. Personally,
over the last ~2.5 years, I have seen checkpatch complaints about `pres`
on several occasions, and all of them were abbreviations for `presence`.
Given the high false positive rate for this entry, comment it out.
Change-Id: I72f1811fb1f766e7de7c4957fd9ba844c0728029
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49463
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5e07584d7857052c7a9388331a475f5a073af038
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: Ie122a441145383b820d96e32ce1581dfc27fa57b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
We no longer need the IO-APIC assignments since we use the GNB IO-APIC.
We were also missing the E-H IRQ mapping. I also renumbered them since
IRQ 8 is used by the rtc.
TEST=none
BRANCH=zork
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia956ae457669aeda6fa49e127373aad3807f7b9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
<td><atarget="_blank"href="http://www.mouser.com/images/microsites/Intel_Galileo2_lrg.jpg"><imgalt="Galileo Gen 2"src="http://www.mouser.com/images/microsites/Intel_Galileo2_lrg.jpg"width=500></a></td>
<td>
The Intel® Galileo Gen 2 mainboard code was developed along with the Intel®
<li>Quadruple Bus Buffer: Texas Instruments <atarget="_blank"href="http://www.ti.com/lit/ds/symlink/sn74lv125a.pdf">SN74LV125A</a></li>
<li>Quadruple Bus Buffer with 3-State Outputs: Texas Instruments <atarget="_blank"href="http://www.ti.com/lit/ds/symlink/sn74lvc126a.pdf">SN74LVC126A</a></li>
<li>Serial EEPROM (1 KiB): ON Semiconductor®<atarget="_blank"href="http://www.onsemi.com/pub_link/Collateral/CAT24C01-D.PDF">CAT24C08</a></li>
<li><atarget="_blank"href="http://download.intel.com/support/processors/quark/sb/sourcedebugusingopenocd_quark_appnote_330015_003.pdf">Hardware Setup and Software Installation</a></li>
<li>USB Serial cable: FTDI <atarget="_blank"href="https://www.google.com/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=FTDI+TTL-232R-3V3">TTL-232R-3V3</a></li>
set PACKAGES_PATH=%WORKSPACE%\edk2;%WORKSPACE%\edk2-non-osi
set EDK_TOOLS_BIN=%WORKSPACE%\edk2-BaseTools-win32
cd edk2
edksetup.bat
</code></pre>
</li>
</ul>
</li>
</ol>
<hr>
<h2><aname="QuarkFsp">Quark™ FSP</a></h2>
<p>
Getting the Quark FSP source:
</p>
<ol>
<li>Set up an EDK-II <ahref="#BuildEnvironment">Build Environment</a></li>
<li>cd edk2</li>
<li>mkdir QuarkFspPkg</li>
<li>cd QuarkFspPkg</li>
<li>Use git to clone <atarget="_blank"href="https://review.gerrithub.io/#/admin/projects/LeeLeahy/quarkfsp">QuarkFspPkg</a> into the QuarkFpsPkg directory (.)</li>
</ol>
<h3>Building QuarkFspPkg</h3>
<p>
There are two versions of FSP: FSP 1.1 and FSP 2.0. There are also two
different implementations of FSP, one using subroutines without SEC and
PEI core and the original implementation which relies on SEC and PEI core.
Finally there are two different build x86 types release (r32) and debug (d32).
</p>
<p>Note that the subroutine implementations are a <b>work in progress</b>.</p>
<li><atarget="_blank"href="https://github.com/tianocore/edk2/tree/master/QuarkPlatformPkg">EDK II firmware for Intel® Quark™ SoC X1000 based platforms</a></li>
added by <atarget="_blank"href="https://review.coreboot.org/gitweb?p=coreboot.git;a=blob;f=src/arch/x86/Makefile.inc;hb=HEAD#l133">src/arch/x86/Makefile.inc</a>
added by <atarget="_blank"href="https://review.coreboot.org/gitweb?p=coreboot.git;a=blob;f=src/arch/x86/Makefile.inc;hb=HEAD#l110">src/arch/x86/Makefile.inc</a>
added by <atarget="_blank"href="https://review.coreboot.org/gitweb?p=coreboot.git;a=blob;f=src/cpu/intel/fit/Makefile.inc;hb=HEAD">src/cpu/intel/fit/Makefile.inc</a>
added by <atarget="_blank"href="https://review.coreboot.org/gitweb?p=coreboot.git;a=blob;f=src/arch/x86/Makefile.inc;hb=HEAD#l137">src/arch/x86/Makefile.inc</a>
</li>
</ul>
<hr>
<h2><aname="TempRamInit">TempRamInit</a></h2>
<p>
Enable the call to TempRamInit in two stages:
</p>
<ol>
<li>Finding the FSP binary in the read-only CBFS region</li>
<li>Call TempRamInit</li>
</ol>
<h3>Find FSP Binary</h3>
<p>
Use the following steps to locate the FSP binary:
</p>
<ol>
<li>Edit the src/soc/<Vendor>/<Chip Family>/Kconfig file
<oltype="A">
<li>Add "select USE_GENERIC_FSP_CAR_INC" to enable the use of
<td>coreboot displays the memory map correctly during the BS_WRITE_TABLES state</td>
</tr>
<tr>
<td>MTRRs</td>
<td>
Set values: src/drivers/intel/fsp1_1/stack.c/<atarget="_blank"href="https://review.coreboot.org/gitweb?p=coreboot.git;a=blob;f=src/drivers/intel/fsp1_1/stack.c;hb=HEAD#l42">setup_stack_and_mtrrs</a><br>
FSP 1.1 MemoryInit called from src/drivers/intel/fsp1_1/<atarget="_blank"href="https://review.coreboot.org/gitweb?p=coreboot.git;a=blob;f=src/drivers/intel/fsp1_1/raminit.c;hb=HEAD#l126">raminit.c</a>
</td>
<td>Select the following Kconfig values
<ul>
<li>DISPLAY_HOBS</li>
<li>DISPLAY_UPD_DATA</li>
</ul>
Testing successful if:
<ul>
<li>MemoryInit UPD values are correct</li>
<li>MemoryInit returns 0 (success) and</li>
<li>The message "ERROR - coreboot's requirements not met by FSP binary!"
<li><atarget="_blank"href="https://github.com/tianocore/tianocore.github.io/wiki/EDK-II-Development-Process">EDK II Development Process</a></li>
<li>EDK II <atarget="_blank"href="https://github.com/tianocore/tianocore.github.io/wiki/EDK%20II%20White%20papers">White Papers</a></li>
<li><atarget="_blank"href="https://github.com/tianocore/tianocore.github.io/wiki/SourceForge-to-Github-Quick-Start">SourceForge to Github Quick Start</a></li>
If access error appeared, then add `iomem=relaxed` to Linux kernel parameters and restart your Linux system.
You can also repeat backup and compare checksums manually.
Backup file should be stored elsewhere, so that in case the coreboot build is faulty, some external procedure can be used without having to extract the backup from the target device first.
### Write new flash image
Let's write new image into SPI flash chip, verify checksum again and erase second flash chip:
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
